Download CD-IB100/XM/E - Wiki Karat

Service
Manual
ORDER NO.
CD-IB100/XM/E
CRT3422
iPod ADAPTER
CD-IB100
/XM/E
For details, refer to "Important check points for good servicing".
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.
PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
C PIONEER CORPORATION 2005
K-ZZB. MAR. 2005 Printed in Japan
1
A
2
3
4
SAFETY INFORMATION
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
B
- Service Precaution
You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
C
D
E
F
2
CD-IB100/XM/E
1
2
3
4
5
6
7
8
[Important Check Points for Good Servicing]
A
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
B
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
C
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
D
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts
E
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
3
CD-IB100/XM/E
5
6
F
7
8
1
A
2
3
4
CONTENTS
SAFETY INFORMATION............................................2
1. SPECIFICATIONS .......................................................4
2. EXPLODED VIEWS AND PARTS LIST ......................5
2.1 PACKING..............................................................5
2.2 EXTERIOR ............................................................6
3. SCHEMATIC DIAGRAM.............................................8
3.1 SCHEMATIC DIAGRAM (GUIDE PAGE) .............8
4. PCB CONNECTION DIAGRAM................................14
4.1 MAIN PCB UNIT ................................................14
B
5. ELECTRICAL PARTS LIST........................................16
6. ADJUSTMENT .........................................................18
7. GENERAL INFORMATION.......................................20
7.1 DIAGNOSIS .......................................................20
7.1.1 DISASSEMBLY.........................................20
7.1.2 CONNECTOR FUNCTION DESCRIPTION ......21
7.2 IC ........................................................................22
8. OPERATIONS ...........................................................24
C
1. SPECIFICATIONS
D
Power source . . . . . . . . . . . . .14.4 V DC (10.8 - 15.1 V allowable )
Grounding system . . . . . . . . .Negative type
Max. current consumption . . .2.0 A
Dimensions ( W x H x D ) . . . .95 x 25 x 91 mm
(3-3/4 x 1 x 3-5/8 in.)
Weight . . . . . . . . . . . . . . . . . . .0.32 kg ( 0.7 lbs )
E
F
4
CD-IB100/XM/E
1
2
3
4
6
5
8
7
2. EXPLODED VIEWS AND PARTS LIST
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
- Screws adjacent to ∇ mark on the product are used for disassembly.
- For the applying amount of lubricants or glue, follow the instructions in this manual.
( In the case of no amount instructions, apply as you think it appropriate.)
2.1 PACKING
14
12
13
1
11
B
5
2
6
2
7
8
C
9
3
4
10
D
- PACKING SECTION PARTS LIST
Mark No. Description
1
2
3
4
5
6
7
8
9
10
Part No.
Protect Bag
Spacer(S)
Spacer(L)
Carton
DC Cord Assy
CZE2966
CZH6631
CZH6632
CZH6635
CZD2993
BUS Cord Assy
Owner’s Manual
Owner’s Manual
Polyethylene Bag
Contain Box
CZD2995
CZR2983
CZR2984
CZE2962
CZH6636
Mark No. Description
*
*
*
11
12
13
14
Velcro Fastener(Hard)
Velcro Fastener(Soft)
Polyethylene Bag
Polyethylene Bag
Part No.
CZE2964
CZE2965
CZE2967
CZE2970
E
- Owner's Manual
Part No.
CZR2983
CZR2984
Language
English, Spanish, German, French, Italian
Dutch, Portuguese(B), Chainese(T), Arabic
F
5
CD-IB100/XM/E
5
6
7
8
1
A
2
3
4
2.2 EXTERIOR
1
14
B
2
3
1
13
12
C
8
4
7
11
10
A
9
D
6
1
1
1
E
5
1
F
6
CD-IB100/XM/E
1
2
3
4
6
5
7
8
- EXTERIOR SECTION PARTS LIST
Mark No. Description
A
Part No.
1
2
3
4
5
Screw
DC Cord Assy
BUS Cord Assy
I/P Cord Assy
Chassis(Bottom)
BSZ26P060FTC
CZD2993
CZD2995
CZD2996
CZN6966
6
7
8
9
10
Insulator
Main PWB Unit
Plug(CN1)
Connector(CN4)
Connector(CN3)
CZN6969
CZW5553
CZK2960
CKS3409
CKS3414
11
12
13
14
Connector(CN2)
Holder(BUS)
Holder(Power Supply)
Chassis(Top)
CKS4833
CZN6967
CZN6968
CZN6999
B
C
D
E
F
7
CD-IB100/XM/E
5
6
7
8
1
2
3
4
3. SCHEMATIC DIAGRAM
3.1 SCHEMATIC DIAGRAM (GUIDE PAGE)
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A
A-a
A-b
A-a
Large size
SCH diagram
F/W POWER
I-POD ISOR
A-a
A-b
A-a
A-b
ACC ID
Guide page
Detailed page
I-POD
I-POD:+1.35dBs
( )
B
PSENS
3.3V
PSENSG
5V
5V
3.3V
NC
NC
NC
NC
NC
NC
NC
IC
NC
NC
NC
NC
NC
TESTO
TESTSI
TESTSCK
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
( )
C
D
NC
NC
NC
NC
NC
NC
PPOWER
NC
NC
VDD
VSS
TESTIN
psensg
NC
NC
NC
NC
NC
NC
NC
SYSTEM CONTROLLER
NC
NC
ROMDATA
NC
NC
NC
NC
NC
NC
NC
reset
NC
NC
VSS
X2
X1
REGOFF
REGC
VDD
MODEL
SYSPW
DALMON
NC
IPPW
IPSELECT
PID
NC
R37 MUTE
NC
47K
NC
NC
AVDD
AVREF1
AVSS
RX
TX
nmi
NC
NC
psens
NC
asens
bsens
NC
RXIPOD
TXIPOD
NC
NC
NC
NC
E
F
A
8
CD-IB100/XM/E
1
2
3
4
6
5
8
7
A-b
A
CD-CH
CD-CH ISOR
A
MAIN PWB UNIT
IP-BUS:+2.00dBs
SW AMP
IP-BUS IN
B
MUTE
IP-BUS:+2.21dBs
I-POD:+2.21dBs
C
IP-BUS OUT
ASENS
8.1V
(
)
D
BSENS
BU
>
)
FUSE
530µH
5.0V
E
(
)
(
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
6
A
9
CD-IB100/XM/E
5
F
7
8
I-POD:+1.35dBs
PSENS
D
3.3V
5V
C
10
1
2
5V
( )
3.3V
I-POD ISOR
B
PSENSG
I-POD
E
ACC ID
F/W POWER
A-a A-b
1
2
3
3
4
A
A-b
F
A-a
CD-IB100/XM/E
4
( )
5
6
7
8
CD-IB100/XM/E
11
A-a
F
E
D
A-a A-b
NC
AVDD
AVREF1
AVSS
RX
TX
nmi
NC
NC
psens
NC
asens
bsens
NC
RXIPOD
TXIPOD
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
IC
NC
NC
NC
NC
NC
TESTO
TESTSI
TESTSCK
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
SYSTEM CONTROLLER
NC
NC
ROMDATA
NC
NC
NC
NC
NC
NC
NC
reset
NC
NC
VSS
X2
X1
REGOFF
REGC
VDD
MODEL
SYSPW
DALMON
NC
IPPW
IPSELECT
PID
NC
MUTE
NC
NC
C
B
R37
47K
NC
NC
NC
NC
NC
NC
PPOWER
NC
NC
VDD
VSS
TESTIN
psensg
NC
NC
NC
NC
NC
NC
NC
A-b
5
7
6
A
8
E
SW AMP
D
ASENS
A
B
1
CD-CH
MAIN PWB UNIT
12
2
2
3
IP-BUS OUT
IP-BUS:+2.21dBs
I-POD:+2.21dBs
IP-BUS IN
IP-BUS:+2.00dBs
A
MUTE
CD-CH ISOR
A-a A-b
1
3
4
C
F
A-b
CD-IB100/XM/E
4
)
BSENS
(
5
6
(
)
8.1V
FUSE
7
7
A-a A-b
>
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
530µH
BU
6
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
5.0V
ASENS
)
(
5
8
CD-IB100/XM/E
8
A
B
C
D
E
F
A-b
13
1
2
3
4
4. PCB CONNECTION DIAGRAM
A
4.1 Main PWB Unit
NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
several destination.
For further information for
respective destinations, be sure
to check with the schematic diagram.
2.Viewpoint of PCB diagrams
Connector
Capacitor
SIDE A
P.C.Board
Chip Part
SIDE B
B
A
MAIN PWB UNIT
SIDE A
IC,Q
DC CONNECTOR
C
D
E
IP-OUT
IP-IN
F
A
14
CD-IB100/XM/E
1
2
3
4
5
6
7
8
A
A
B
MAIN PWB UNIT
SIDE B
IC,Q
C
D
E
F
A
15
CD-IB100/XM/E
5
6
7
8
1
A
2
3
4
5. ELECTRICAL PARTS LIST
NOTE:
Parts whose parts numbers are omitted are subject to being not supplied.
The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
The > mark found on some component parts indicatesthe importance of the safety factor of the part.
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
B
Part No.
-------------------------
Unit Number : CZW5553
: Main PWB Unit
A Unit Name
MISCELLANEOUS
C
D
E
IC
IC
IC
IC
IC
1
2
3
4
5
IC
IC
IC
IC
IC
BA3131FS
TA2050FS1
HA12240FP
PE5483A
TC7SET08FUS1
IC
IC
IC
Q
Q
6
7
9
1
2
IC
IC
IC
Transistor
Transistor
TC7SH08FUS1
PST3433UL
TA2050FS1
IMH3A
DTA114EU
Q
Q
Q
Q
Q
3
4
5
6
7
Transistor
Transistor
Transistor
Transistor
Transistor
DTC124EU
2SD1767
2SC2412K
2SA1162
DTC144EU
Q
Q
Q
Q
Q
8
9
10
11
15
Transistor
Transistor
Transistor
Transistor
Transistor
DTC144EK
2SD1767
DTC124EU
DTA114EU
DTC124EU
Q
Q
Q
Q
Q
16
17
18
19
20
Transistor
Transistor
Transistor
Transistor
Transistor
2SC4081
DTC114EU
2SB1708
2SA1162
DTC124EU
Q
Q
Q
Q
Q
23
25
27
28
29
Transistor
Transistor
Transistor
Transistor
Transistor
DTC114EU
DTC114EU
2SB1708
DTA114EU
DTC124EU
D
D
D
D
D
1
2
3
4
5
Diode
Diode
Diode
Diode
Diode
1SR154-400
HZS6L(B1)
HZS7L(C2)
1SS355
HZS9L(B2)
D
D
D
D
D
7
9
14
25
29
Diode
Diode
Diode
Diode
Diode
HZS4LL(B)
1SR139-400
HZM6.2ZMWA
1SS355
HZM6.2ZMWA
D
L
L
X
30
1
2
1
Diode
Choke Coil 530µH
Inductor
Radiator 12.583MHz
HZS22L(1)
CTH1282
CZT2935
CSS1601
RESISTORS
F
R
R
R
R
R
1
2
3
4
5
RS1/16S103J
RS1/16S0R0J
RS1/16S124J
RS1/16S124J
RS1/16S181J
16
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
R
R
R
R
R
6
7
8
9
10
RS1/16S181J
RS1/16S223J
RS1/16S223J
RS1/16S102J
RS1/16S102J
R
R
R
R
R
11
12
13
14
15
RS1/16S223J
RS1/16S223J
RS1/16S473J
RS1/16S473J
RS1/16S473J
R
R
R
R
R
16
17
18
19
20
RS1/16S562J
RS1/16S123J
RS1/16S912J
RS1/16S473J
RS1/16S473J
R
R
R
R
R
21
22
23
24
25
RS1/16S473J
RS1/16S123J
RS1/16S562J
RS1/16S473J
RS1/16S821J
R
R
R
R
R
26
27
28
29
30
RS1/16S821J
RS1/16S101J
RS1/16S101J
RS1/16S103J
RS1/16S333J
R
R
R
R
R
31
32
34
35
36
RS1/16S102J
RS1/16S103J
RS1/16S912J
RS1/16S473J
RS1/16S104J
R
R
R
R
R
37
38
39
43
44
RS1/16S473J
RS1/16S473J
RS1/16S103J
RS1/16S0R0J
RS1/16S222J
R
R
R
R
R
45
46
47
48
49
RS1/16S622J
RS1/16S0R0J
RS1/16S101J
RS1/16S104J
RS1/16S223J
R
R
R
R
R
50
51
52
53
54
RS1/16S0R0J
RS1/16S102J
BPR26CR39J
RS1/16S0R0J
RS1/16S101J
R
R
R
R
R
55
56
58
59
60
RS1/16S104J
RS1/16S103J
RS1/16S473J
RS1/16S473J
RS1/16S222J
R
R
R
R
R
61
62
63
64
65
RS1/16S103J
RS1/16S473J
RS1/16S103J
RS1/16S473J
RS1/16S473J
CD-IB100/XM/E
1
2
3
4
5
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
6
Part No.
-------------------------
7
8
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
R
R
R
R
R
66
67
70
72
73
RS1/16S104J
RS1/16S472J
RS1/16S0R0J
RS1/16S514J
RS1/16S393J
C
C
C
C
C
35
37
39
41
42
CKSRYB103K50
CKSRYB103K50
CKSRYB103K50
CEAT1R0M50
CKSQYB104K50
R
R
R
R
R
74
75
76
77
80
RS1/16S102J
RS1/16S102J
RS1/16S102J
RS1/16S102J
RS1/16S103J
C
C
C
C
C
43
44
47
48
49
CKSRYB104K50
CKSRYB104K50
CKSRYB104K50
CKSRYB104K50
CKSRYB104K50
R
R
R
R
R
82
83
84
86
87
RS1/16S102J
RS1/16S133J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
C
C
C
C
C
50
51
52
53
54
CKSRYB104K50
CKSRYB104K50
CKSRYB104K50
CCSRCH102J50
CCSRCH102J50
R
R
R
R
R
88
89
91
94
97
RS1/16S102J
RS1/16S102J
RS1/16S102J
RS1/16S473J
RS1/16S473J
C
C
C
C
C
59
60
61
62
63
CEAL4R7M25
CEAL4R7M25
CEAL4R7M25
CEAL4R7M25
CEAL220M10
R
R
R
R
R
98
99
100
101
103
RS1/16S124J
RS1/16S103J
RS1/16S223J
RS1/16S223J
RS1/16S102J
C
C
C
C
C
64
70
71
72
73
CEAL220M10
CKSRYB104K50
CKSRYB104K50
CEAT101M10
CKSRYB103K50
R
R
R
R
R
106
107
108
109
110
RS1/16S103J
RS1/10S220J
RS1/10S220J
RS1/8S0R0J
RS1/16S472J
R
R
R
R
111
112
113
114
RS1/16S472J
RS1/16S104J
RS1/16S104J
RS1/8S0R0J
A
B
C
CAPACITORS
C
C
C
C
C
1
2
3
4
7
1000µF/16V
470µF/16V
CCH1234
CCH1080
CEAT101M10
CKSRYB103K50
CKSRYB104K50
C
C
C
C
C
8
9
10
11
12
CEAT1R0M50
CEAT1R0M50
CEAT1R0M50
CEAT1R0M50
CEALNP100M10
C
C
C
C
C
13
14
15
16
17
CEALNP100M10
CEAT220M10
CEAT220M10
CEAT220M10
CEAT101M10
C
C
C
C
C
18
19
20
21
22
CEAT470M10
CEALNP100M10
CEALNP100M10
CEAT470M6R3
CKSRYB103K50
C
C
C
C
C
23
24
25
26
27
CKSRYB102K50
CKSRYB102K50
CEAL470M6R3
CKSRYB103K50
CKSRYB104K50
C
C
C
C
C
28
30
31
32
33
CEAL470M6R3
CEAT100M35
CEAT100M35
CKSRYB104K50
CEAT101M10
D
E
F
17
CD-IB100/XM/E
5
6
7
8
1
2
3
4
6. ADJUSTMENT
A
Test mode
Test mode is the special mode used for the check of the failure state of an iPod adapter, or isolation of failure with iPod.
-Test mode function
(1) Check of communication between an iPod adapter and a main unit
(2) Check of charge function
(3) Change of test mode cancellation trigger
(4) Check of voice line of an iPod adapter (iPod is required)
B
<How to enter in the test mode>
By putting a main unit into the test mode, an iPod adapter also enters in the test mode operation.
(The way to enter in the test mode is according to the specification of a main unit.)
Example) In the case of DEH-P6700MP/XN/UC (IP-BUS model) pressing 4 + 6 Key simultaneously Reset
<How to cancel the test mode >
AccOFF/RESET (main unit) cancels the test mode.
Connect an iPod adapter to a main unit and enter in the test mode.
(1) Check of communication between an iPod adapter and a main unit
C
When switching source of a main unit to EXT (iPod), the following displays appear.
- It is possible to check whether communication between an iPod adapter and a IP-BUS is normal.
- It is possible to identify which one of "unexpected connection" or "connection in a schedule" the model is in the
state of a display.
Display at the time of unexpected connection
i
P o d
- 0
0 These 8 figures are displayed.
D
Display at the time of connection in a schedule
* *
*
*
*
* 0
0 is displayed.
Note * portion may change with models and may be blank.
(2) Check of charge function
When pressing 1 key of 1 - 6 keys of a main unit, it is possible to turn ON/OFF of a charge circuit of the iPod adapter.
By checking ON/OFF of the No. 1 pin of a DOCK connector at the iPod adapter side and a backup power supply in
the No. 11 or 12 pin at an iPod side, it is possible to check whether the charge circuit system is running normally.
Since the state of charging is displayed if an iPod is connected, it is also possible to check whether charging is performed
normally.
E
Display sample (in the case of an unexpected connection unit).
i
P o
d
- 0
0 Charge circuit OFF
i
P
o
d
-
-
1
0
Charge circuit ON
(3) Change of test mode cancellation trigger
When pressing 2 key of 1 - 6 keys of a main unit, it is possible to change the cancellation trigger in test mode to either
AccOFF or RESET.
Display sample (in the case of a connection unit in a schedule)
*
*
*
*
* *
0 0 Cancellation trigger Acc OFF
F
*
*
*
*
* *
0 1 Cancellation trigger RESET
Although it is not usually used in the service, if setting up accidentally, cancel it by Backup OFF.
18
CD-IB100/XM/E
1
2
3
4
5
6
7
8
(4) Check of voice line of an iPod adapter (iPod is required)
A
Usually, when iPod is connected, it becomes impossible to use the key of iPod except RESET, but if it enters in this mode,
it is possible to operate the other keys.
- An iPod adapter does not check whether the iPod has been connected, and it is possible to operate on an IP-BUS.
- Since communication with an iPod is not performed, a logo (pioneer) is not displayed on the iPod.
Since it is possible to produce a sound by playing an iPod, when the sound of the iPod does not come out from a main unit,
it shows that the iPod is out of order.
In the normal mode, since communication of data and charging are performed, a logo (pioneer) and "now charging" are
displayed in the window of the iPod.
By checking whether the keys of an iPod are operatable or not, it is possible to see if it is normal or not.
B
C
D
E
F
19
CD-IB100/XM/E
5
6
7
8
1
A
2
3
4
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
- Removing the Chassis (Fig.1)
Chassis
1
Remove the two screws and then
remove the Chassis.
B
1
1
C
Fig.1
- Removing the Main PWB Unit (Fig.2)
2
1
2
Straighten the tab at location indicated.
1
2
D
Remove the four screws and then remove
the Main PWB Unit.
2
2
E
Fig.2
Main PWB Unit
F
20
CD-IB100/XM/E
1
2
3
4
6
5
8
7
7.1.2 CONNECTOR FUNCTION DESCRIPTION
A
B
11
7
4
1
10
3
2
9
9
2
3
10
6
6
5
8
PIN 30
C
PIN 1
5
8
1
11P CONNECTOR IP-BUS BLUE
1
2
3
4
5
6
7
8
9
10
11
BUS +
BUSG1
BUSG1
NC
BUS BUSG1
BUSL1
ASENS
BUSR1
BUSR2
BUSL2
4
7
11
1
11P CONNECTOR IP-BUS BLACK
1
2
3
4
5
6
7
8
9
10
11
CORD ASSY CONNECTOR
BUS +
BUSG5
BUSG5
NC
BUS BUSG5
BUSL3
ASENS
BUSR3
BUSAG1
BUSAG1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
F/W GND
F/W GND
ACC ID
F/W PWR
F/W PWR
ACC PW
USB/DGND
USB/DGND
DOCK TX
DOCK RX
USB/DGND
AUDIO L
AUDIO R
AUDIO GND
SGND
3
2
DC CONNECTOR
1
2
3
GND
B.U
D
E
F
21
CD-IB100/XM/E
5
6
7
8
1
2
3
4
7.2 IC
Pin Functions (PE5483A)
A
B
C
D
E
Pin No.
1,2
3
4-10
11
12,13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29-37
38
39
40
41
42,43
44
45-64
65
66
67
68-72
73
74-81
82
83
84
85
86
87
88,89
90
91
92
93
94
95
96
97-100
Pin Name
NC
ROMDATA
NC
reset
NC
VSS
X2
X1
REGOFF
REGC
VDD
MODEL
SYSPW
DALMON
NC
IPPW
IPSELECT
PID
NC
MUTE
NC
psensg
TESTIN
VSS
VDD
NC
PPOWER
NC
TESTSCK
TESTSI
TESTO
NC
IC
NC
AVDD
AVREF1
AVSS
RX
TX
nmi
NC
psens
NC
asens
bsens
NC
RXIPOD
TXIPOD
NC
I/O
I/O
I
I
I
O
O
O
O
O
O
I
I
O
O
I
O
I
I
O
I
I
I
I
I
O
Function and Operation
Not used
ROM data input / output
Not used
Chip reset input
Not used
GND
Crystal connection for system clock oscillation
Crystal connection for system clock oscillation
Regulator operation specification signal
Capacity connection for regulator output stability
Power supply
Model select input
System power control output
System operation situation output
Not used
Driver power control output
Selector switch output
Communication mode (UART) notification output
Not used
Mute output
Not used
Connection sense input
Chip test input
GND
Power supply
Not used
Power control output
Not used
Serial clock output
Serial data input
Serial data output
Not used
GND
Not used
Power supply for A/D converter
Standard voltage for A/D converter
GND for A/D converter
Data input (IE-BUS)
Data output (IE-BUS)
NMI input
Not used
Connection sense input
Not used
ACC sense input
Backup sense input
Not used
Serial data input
Serial data output
Not used
*PE5483A
80
51
81
50
100
31
IC's marked by * are MOS type.
Be careful in handling them because they are
very liable to be damaged by electrostatic
induction.
F
1
30
22
CD-IB100/XM/E
1
2
3
4
6
5
7
8
PST3433UL
A
4 VSS
VOUT 1
B
VDD 2
Vref
3 NC
TC7SET08FUS1, TC7SH08FUS1
5 VCC
IN B 1
C
IN A 2
4 OUT Y
GND 3
D
E
F
23
CD-IB100/XM/E
5
6
7
8
1
A
2
3
4
8. OPERATIONS
Multi-CD player
(sold separately)
Head unit
IP-BUS cable
B
IP-BUS cable
1.5 m (4 ft. 11 in.)
Black
To IP-BUS input
(blue)
Blue
This unit
iPod, iPod mini or iPod Photo
C
Dock connector port
Label
(+Battery)
1.5 m (4 ft. 11 in.)
Dock connector
D
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Fuse (2 A)
E
Black (ground)
To vehicle (metal) body.
F
24
CD-IB100/XM/E
1
2
3
4
5
6
7
8
A
B
C
D
E
F
25
CD-IB100/XM/E
5
6
7
8
1
2
1
2
3
4
3
4
A
B
C
D
E
F
26
CD-IB100/XM/E