Download ALPHARD SR / SA / S - Wald International

ALPHARD SR / SA / S
AGH30W/35W
GGH30W/35W
AYH30W
INSTALLATION MANUAL
(2015y～)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD SIDE STEPS FOR TOYOTA 30 ALPHARD SR/SA/S.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
PARTS
SIDE STEP
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
QUANTITIES
1SET
SIDE STEPS
Use caulking glue
to fill the gap
between the product
and the body.
SIDE STEP
【BEFORE PAINTING】
１） Remove OEM sidesteps according to the TOYOTA service manual.
２） Use OEM anchors to temporarily install WALD Side Steps to the body.
※ Adjust the details of WALD Sides Steps to fit the body by rasps or sandpapers.
３） Mark the location of WALD Side Steps with the masking tape after checking the balance.
４） Paint WALD Side Steps according to the picture.
【AFTER PAINTING】
５） Remove OEM inner panel from OEM side steps, then replace to WALD Side Steps. (As per enclosure)
６） Completely degrease the installation position.
７） Use caulking glue to install WALD Side Steps to the body.
８） Use OEM tapping screws to fix WALD Side Steps tightly.
※ After completely fixed, use OEM tapping screws on the slide door.
９） Leave them till completely fixed.
※WALD SHOWCAR IS PAINTED LIKE THE PICTURE (STEP 4)
OEM
TAPPING SCREWS
MATTE BLACK
※ The edge of WALD Side Steps has
the concave shape to make the space
to dodge OEM rear fender.
OEM TAPPING SCREW
※After completely fixed with caulking glue,
use OEM tapping screws on the slide door.
ATTENTION
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK. DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
OEM ANCHOR
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
2015/10