Download KDC-9090R

Transcript
KDC-9090R
MICROCOMPUTER'S TERMINAL DESCRIPTION
4
Pin
47
48
49
Function
IC2TYPE1
CH-REQH
CH-RST
I/O
I
O
O
Description
IC2 destination terminal
Request output to changer
Reset output to changer
50
51
52
53
54
55
56
57
CH-MUTE
CH-CON
ILL-ON
M-MUTE L
M-MUTE R
BVdd
BVss
M-RST
I
O
O
I
I
O
Mute request from changer
Changer control output
FL, illumination output
Mute request from CD mechanism
Mute request from CD mechanism
+B terminal
GND terminal
Reset output to CD mechanism
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
M-STOP
N.C
LO/EJ
MOSW
N.C
CD-SW3
PAN-RESET
MC-REQ/PAN
N.C
N.C
N.C
N.C
AVCONT
Avdd
Avss
Avref
PHONE
SRM-SW3
SRM-SW1
SRM-SW2
SRM-DET
NOISE
S-METER
R-DATA
O
O
I/O
O
O
I
O
I/O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
Stop request to CD mechanism
Open (not used)
CD mechanism, LODING, EJECT selector
CD mechanism, MOTOR, SW
Open (not used)
CD down SW detection terminal
Reset output to panel microprocessor
REQ terminal/panel detection for panel microprocessor
Open (not used)
Open (not used)
Open (not used)
Open (not used)
AD reference voltage control output
+B terminal
GND terminal
Reference voltage supply terminal for A/D converter
PHONE detection terminal
Mask mechanism position detection input
Mask mechanism position detection input
Mask mechanism position detection input
Mask mechanism detection input
FM noise detection terminal
S meter detection terminal
RDS DECODER DATA input terminal
82
R-QUAL
I
RDS DECODER QUAL input terminal
83
84
85
86
87
IFC-OUT
N.C
N.C
SRM-B
R-CLK
I
I
I
O
I
F/E IFC OUT input terminal
Open (not used)
Open (not used)
SRM mechanical submotor output terminal
RDS DECODER CLK input terminal
88
89
90
91
92
93
94
95
96
97
98
99
100
CH-REQC
SC-REQ
CD-SW1
CD-SW2
SRM+B
BU-DET
CH-DATAC
CH-DATAH
CH-CLK
SC-DATA
MC-DATA
MC-CLK
PAN5V
I
I
I
I
O
I
I
O
I/O
I
I/O
O
O
Input request from changer
Communication request from panel microprocessor
LOADING SW detection terminal
12cm disk detection switch terminal
SRM mechanical submotor output terminal
Momentary power down detection terminal
Data input terminal from changer
Data input terminal to changer
CLK I/O terminal used with changer
Data line from panel microprocessor
Data line to panel microprocessor
CLK terminal to panel microprocessor
Panel 5 volt control terminal
Processing Operation
L: During default
Normally L, after system RST reset is ”H” for
400ms and then ”L”
ON: H
OFF: L
ON: H
OFF: L
ON: H
OFF: L
ON: L
ON: L
Normally H,
L:During reset
Per mechanical control specs.
Stop: L
H: During CD
Stop, Brake: Hi-z, LOADING: L, EJECT: H
LOADING, EJECT, Brake: H
Chucking: H
Normally H, L: During reset, momentary power down
L: During panel use
Same timing as P ON
H: During operation
Tel mute: Min 1 volt, Navi mute: Max.2.5 volt
See 01mask mechanical position detection chart
See 01mask mechanical position detection chart
See 01mask mechanical position detection chart
L: Mechanism
H: No mechanism
Connect to GND: On models without RDS,
RBDS
Connect to GND: On models without RDS,
RBDS
L: When station present
Connect to GND
Connect to GND
Connect to GHD: On models without RDS,
RBDS
ON: L
LOADING start: L
12cm DISC: L
L: B.U
H: No B.U (momentary power down)
L: Panel
H: No panel