Download service manual super audio cd player

SCD-XE600
SERVICE MANUAL
E Model
Ver 1.0 2004.10
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM66D-DVBU50
Base Unit Name
DVBU50
Optical Traverse Unit Name
DBU-3
SPECIFICATIONS
When a Super Audio CD is played
General
Playing frequency range 2 Hz to 100 kHz
Frequency response
2 Hz to 40 kHz (–3 dB)
Dynamic range
100 dB or more
Total harmonic distortion rate
0.0035 % or less
Wow and flutter
Value of measurable limit
(±0.001 % W. PEAK) or
less
Laser
When a CD is played
Mass (approx.)
Frequency response
2 Hz to 20 kHz
Dynamic range
96 dB or more
Total harmonic distortion rate
0.0039 % or less
Wow and flutter
Value of measurable limit
(±0.001 % W. PEAK) or
less
Power requirements
Power consumption
Dimensions (w/h/d)
Semiconductor laser
(Super Audio CD: λ= 650
nm) (CD: λ= 780 nm)
Emission duration:
continuous
110 V AC, 60 Hz
15 W
430 × 95 × 283 mm incl.
projecting parts
3.1 kg
Supplied accessories
Audio connecting cord
Remote commander
Battery
Red and White 2 (1)
RM-SX800 (1)
R6 (size-AA) (2)
Design and specifications are subject to change
without notice.
Output connector
Jack type Output
level
Load
impedance
ANALOG Phono
5.1CH OUT jacks
2 Vrms (at Over 10
50 kilohms) kilohms
DIGITAL
Square
(CD) OUT optical
OPTICAL* output
connector
–18 dBm
(Light
emitting
wave length:
660 nm)
* Output only the audio signals of the CD
SUPER AUDIO CD PLAYER
9-879-168-01
2004J0579-1
© 2004.10
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
SCD-XE600
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
TABLE OF CONTENTS
1. SERVICING NOTES ......................................................... 3
2. GENERAL ............................................................................ 4
3. DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
Disassembly Flow .............................................................. 6
Case (408226) ..................................................................... 6
Main Board ......................................................................... 7
Panel Loading ..................................................................... 7
Front Panel Block ............................................................... 8
CD Mechanism Deck (CDM66D-DVBU50) ..................... 8
Base Unit (DVBU50) ......................................................... 9
RF Board, Optical Traverse Unit ........................................ 9
Loading Board, Motor (L) Assy (Loading) (M151) ......... 10
4. TEST MODE ...................................................................... 11
This appliance is classified as a CLASS 1
LASER product.
This label is located on the rear exterior.
5. DIAGRAMS
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
5-8.
5-9.
Block Diagram ................................................................. 12
Printed Wiring Board – RF Board – ................................. 14
Schematic Diagram – RF Board – .................................... 15
Printed Wiring Boards – MAIN Board – .......................... 16
Schematic Diagram – MAIN Board (1/4) – ..................... 17
Schematic Diagram – MAIN Board (2/4) – ..................... 18
Schematic Diagram – MAIN Board (3/4) – ..................... 19
Schematic Diagram – MAIN Board (4/4) – ..................... 20
Printed Wiring Boards
– Display, Power Supply Section – .................................. 21
5-10. Schematic Diagram
– Display, Power Supply Section – .................................. 22
6. EXPLODED VIEWS
6-1. Main Section ..................................................................... 28
6-2. Front Panel Section .......................................................... 29
6-3. CD Mechanism Deck Section
(CDM66D-DVBU50) ....................................................... 30
6-4. Base Unit Section (DVBU50) .......................................... 31
7. ELECTRICAL PARTS LIST ......................................... 32
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
SCD-XE600
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
CLEANING OF OPTICAL PICK-UP LENS
In cleaning the lens of optical pick-up, use the air blower.
Never use a cotton swab for cleaning the lens of optical pick-up,
which otherwise causes a trouble.
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURNS OFF
cam (66)
2 Pull out the tray in the
direction of arrow B.
B
A
1 Insert a flat-head screwdriver in to a hole
at the bottom, and rotate the cam (66) in
the direction of arrow A.
3
SCD-XE600
SECTION 2
GENERAL
This section is extracted from
instruction manual.
Index to Parts and Controls
Further details are provided on the pages indicated in parentheses.
Instructions in this manual describe the controls on the player. You can also use the controls on the
remote if they have the same or similar names as those on the player.
Front Panel
1
2
3
4
5
6
7
8
l
qh
qg
qf qd
qa q;
A POWER switch
J X button
B SA-CD/CD button
Each time you press the button while playing back
a hybrid disc, the layer to be played back switches
between the SA-CD layer and the CD layer.
K H button
C PLAY MODE button
Press to select the play mode.
D Disc tray
E MULTI CHANNEL DECODING indicator
Turns on when you turn on the player, or when the
Multi-channel Super Audio CD is loaded and
select the multi-channel playback area by pressing
MULTI/2CH.
F A button
G x button
H m/M buttons
I l AMS L dial
(AMS: Automatic Music Sensor)
4
qs
L
9
L Display window
M Remote sensor
N TIME/TEXT button
Each time you press the button, the playing time of
the track, the remaining time of the disc, or TEXT
information appears in the display.
O MULTI/2CH button
Press to select the playback area when a disc with
the 2 channel area and the multi-channel area is
loaded.
P MENU button
Press to enter the menu.
Press to exit from the menu and return to the
normal display.
SCD-XE600
A CD1/2 (command mode) switch
Select the command mode.
Remote
1
qg
2
qf
3
qd
4
qs
5
B CONTINUE button
Press to resume Continuous Play from Shuffle Play
or Program Play.
SHUFFLE button
PROGRAM button
C TIME/TEXT button
Each time you press the button, the playing time of
the track, the remaining time of the disc, or TEXT
information appears in the display.
D DISPLAY MODE button
Press to turn the display information off or on.
E m/M buttons
F CLEAR button
Press to delete a programed track number.
G LEVEL ADJ button
Press to adjust the output level balance for the
Multi-channel management function.
qa
H ENTER button
q;
9
6
7
8
I CHECK button
Press to check the programed order.
J REPEAT button
K H button
X button
x button
L AMS ./> buttons
(AMS: Automatic Music Sensor)
M SA-CD/CD button
Each time you press the button while playing back
a hybrid disc, the layer to be played back switches
between the SA-CD layer and the CD layer.
N MULTI/2CH button
Press to select the playback area when a disc with
the 2 channel area and the multi-channel area
(page 5) is loaded.
O DISC SKIP +/– buttons*
Press to select the disc.
*This button cannot be used in this player.
5
SCD-XE600
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
Note 1: The process described in
can be performed in any order.
Note 2: Without completing the process described in
, the next process can not be performed.
SET
3-2. CASE (408226)
(Page 6)
3-4. PANEL LOADING
(Page 7)
3-3. MAIN BOARD
(Page 7)
3-5. FRONT PANEL BLOCK
(Page 8)
3-6. CD MECHANISM DECK
(CDM66D-DVBU50)
(Page 8)
3-7. BASE UNIT (DVBU50)
(Page 9)
3-9. LOADING BOARD,
MOTOR (L) ASSY
(LOADING) (M151)
(Page 10)
3-8. RF BOARD,
OPTICAL TRAVERSE
UNIT (DBU-3)
(Page 9)
Note: Follow the disassembly procedure in the numerical order given.
3-2.
CASE (408226)
4 case (408226)
1 two screws
(case 3 TP2)
3 screw
(BVTP 3 × 8)
2 two screws
(case 3 TP2)
6
SCD-XE600
3-3.
MAIN BOARD
1 wire (flat type) (13 core)
(CN301)
2 connector
(CN901)
1 wire (flat type) (31 core)
(CN702)
3 screw
(BVTP 3 × 8)
6 MAIN board
4 three screws
(BVTP 3 × 8)
2 connector
(CN151)
3-4.
5 PC board holder
PANEL LOADING
4 panel loading
3 tow claws
cam (66)
2 Pull out the tray in the
direction of arrow B.
B
A
1 Insert a flat-head screw driver in to
a hold at the bottom, and rotate the
cam (66) in the direction of arrow A.
7
SCD-XE600
3-5.
FRONT PANEL BLOCK
2 connector
(CN101)
1 wire (flat type) (31 core)
(CN301)
4 claw
2 connector
(CN891)
5 front panel block
4 claw
3 three screws
(BVTP 3 × 8)
3-6.
CD MECHANISM DECK (CDM66D-DVBU50)
3 three screws
(BVTP 3 × 8)
4 CD mechanism deck
(CDM66D-DVBU50)
2 connector (CN151)
1 wire (flat type) (31 core)
(CN702)
8
SCD-XE600
3-7.
BASE UNIT (DVBU50)
2 optical pick-up block
(DVBU50)
1 floating screw
(DIA. 12)
3-8.
RF BOARD, OPTICAL TRAVERSE UNIT
6 three step screws (M3)
7 optical traverse unit
(DBU-3)
2 claw
3 flexible flat cable (24 core)
(CN001)
5 RF board
4 flexible board
(CN003)
1 two screws
(BTTP M2.6)
9
SCD-XE600
3-9.
LOADING BOARD, MOTOR (L) ASSY (LOADING) (M151)
5 belt (LD)
4 gear (LD)
6 two screws
(B2.6 × 4)
1 two claws
3 tray (66)
9 motor (L) assy (loading)
(M151)
8 LOADING board
2
7 Remove two solders.
10
SCD-XE600
SECTION 4
TEST MODE
PANEL CHECK MODE
Procedure:
1. While pressing the m button and l AMS L knob, press the [POWER] button to turn the power on.
2. When enter the Panel Check mode, fluorescent indicator tube and LED all lights up for 5 seconds.
3. Press the H key of remote commander to enter the Key Check mode and display “KEY CHECK 12”.(*1)
4. Each button is pressed, the display number of “KEY CHECK” is increases.
5. All buttons of twelve are pressed, exit the Key Check mode and enter the Jog Check mode, then display “JOG CHECK”.
6. Turn the l AMS L knob clockwise until “15” is displayed on the calendar area.
7. Turn the l AMS L knob counterclockwise until “1” is black out on the calendar area and jog check is OK and display “TEST
END”.
8. Press the [POWER] button to turn the power off and release the Panel Check mode.
*1) If press the x key, it displays “KEY CHECK 19”. However, this mode is for the model with changer. Therefore, it does not become OK
unless 19 buttons are pressed. If entered to this mode by mistake, press the [POWER] button to turn the power off and repeat operation
form step 1.
TEST MODE
1. Entering The Test Mode
While press the [MENU] button and l AMS L knob, press the [POWER] button to turn the power on and enter the Test Mode and
display “DIAG MODE”.
2. Operating The Test Mode
Procedure:
1. Turn the l AMS L knob to select the command number (hexadecimal number) (refer to the following table for command
number).
2. Press the l AMS L knob to execute the selected command item.
3. Releasing The Test Mode
Press the [POWER] button to turn the power off.
4. The Commands in Test Mode
Command No.
12
Command name
LD ON/OFF
Item
Turn on/off the laser diode
13
SPIN ON/OFF
Turn on/off the spindle motor
14
FSRV ON/OFF
Turn on/off the focus servo
15
TSRV ON/OFF
Turn on/off the tracking servo
16
CLV ON/OFF
Turn on/off the spindle CLV servo, when both focus servo and tracking servo are on
17
SSRV ON/OFF
Turn on/off the spindle CLV servo, when all servo of focus servo, tracking servo and spindle
servo are on
18
ALL SRV ON
Turn on all servo
19
ALL SRV OFF
Turn off all servo
1A
DISC STOP
Stop the disc rotation (useful as overdrived)
24
ADJ FCSBIAS
Automatically adjust the focus bias (*2)
27
FOCUS AGC
Automatically adjust the focus servo gain (*2)
31
PI/FE OFSET
Automatically adjust the offset signal of PI, PE and TE (*2)
45
TRACKING AGC
Automatically adjust the focus servo gain (*2)
61
DISC DETECT
Judge the disc type (when SA-CD, “SL” or “DL” is displayed)
7C
FJUMP TEST
Focus jump test mode
81
SYSTEM VERSION
Display the version of system microcomputer for 2 seconds
82
I/F VERSION
Display the version of IF microcomputer for 2 seconds
92
ERR CHECK
Error rate display (to stop, press the x button)
for CD display “92 C1 C2 0xff”
for SA-CD display “92 PI1 PO PI2”
93
WATER MARK
WaterMark display
display “93
xxxx” (“xxxx” is value of pspamp)
9D
PLAY&RFD ON
Measuring the jitter (to stop, press the x button)
display: “9D xx 0xff 0xff” (“xx” is measuring value of jitter)
*2) Not used in servicing
11
SCD-XE600
SECTION 5
DIAGRAMS
5-1.
BLOCK DIAGRAM
OPTICAL TRAVERSE UNIT (DBU-3)
VCC
6,14
A5V
VC
5
3
9
1 RFIP
A
14 A
B
13 B
2
C
1
7
D
12 C
11 D
E
15 E
F
10
16 F
Q001
17
LD
DRIVE
DVDLD
25 DVDLD
190 RFAC
SIGO 59
15
12
LD
DRIVE
CDLD
SW
26 CDLD
2 PD
200 TEI
CDBCK 95
FE 42
201 FEI
CDLRCK 94
PI 36
202 PI
4
PDATA VOUTL 9
DSALS 85
3
PBCK
TZC 37
230 TZC
DSARS 86
5
PLRCK
DFT 38
229 DFCTI
DSAC 89
1
DSDL
2
DSDR
SRD 45
245 SSI
SWD 46
246 SSO
SCLK 47
247 SCK
SDEN 48
244 SCS
LDON 27
234 INLIM
DSPHREFO 78
LIMIT
IN
SWITCH
IC712
MOTOR/COIL DRIVER
FOCUS
COIL
37 DO1+
IC705
MASTER CONTROL
MCKI 3
21-29
D0-7
11-18
XINT 32
92 XINT0
XCS 33
87 XCS
73 XWAIT
215 FDOP
71 XWR
XWR 35
XRD 36
FCSTR+
TRACKING
COIL
36 DO1-
IN1- 1
216 FDON
35 DO2+
IN2+ 3
213 TDOP
D511
XRST 37
IC701
RESET
OUT 6
TR-
34 DO2-
203 SEI
IC702
EEPROM
IN3+ 6
M902
(SLED)
SLASLB+
M
SLB-
30 DO4+
220 SLDB
IN3- 7
29 DO432 DO3+
IN4+ 9
SPMM901
(SPINDLE)
28 DO5+
IN5+ 12
206 VCO
SPM+
27 DO546 OPIN147 OPIN1+
MD0-15
222 MDP0
XRAS,
XCAS,
XMWR,
MCKE,
MMCK,
LDQM,
UDQM
IN5- 13
204 SP RV
OPOUT1 45
235 FGMODE
LOADP
M151
M
(LOADING)
LOADN
MA0-10,BA
221 MDS0
14 ZEROR
MZL 95
13 ZEROL
24 DO6-
12
16
R MUTE
Q305
R MUTE 97
M/2 100
IC230
DAC
LOAD S0 25
IN
LOAD S1 27
OUT
DSDR
SL
SR
MUTE
IC430(2/2) Q431,432
AMP
2
1
MUTE
Q531,532
16 MC
15 MD
IC200
DAC
7
PBCK
DQ0-15
PLRCK VOUTR 10
1
DSDL
2
DSDR
RAS,
CAS,
WE,
CKE,
CLK,
LDQM,
UDQM
EXTAL 65
RESET 6
17 SIRCS
SO1 9
SI1 8
3
ANI1-3
6
7
CENTER
SW
SW
MUTE
IC460(2/2) Q462,463
AMP
2
1
18 PSCK
IC801
DISPLAY CONTROLLER
RM 1
CENTER
20 DBCK
X321
11.2896MHz
5
6
9
D509
IC802
SIRCS
VOUTL 9
IC460(1/2)
AMP
19 DSCK
MUTE5 21
ACK 12
SCK1 7
REQ 15
17 MS
8
3
4
11
10
13
12
1
2
15 MD
VF2
VFL
IC703
+1.8V REG
+1.8V
3
IC920
+3.3V REG
+3.3V
1
3
VFL REG
Q971
RECT
D921-924
1
84 IFSI
IC950
+5V REG
83 IFSO
91 XIFINT
85 IFSC
+5V
3
+12V
RECT
D931-934
1
96 XIFCS
IC985
AU+ REG
MUTE
11 P23
AU+
D801
SCD-XE600
12
12
T101
POWER TRANSFORMER
VF1
IC320
INVERTER
36 SP ON
MUTE
Q562,563
16 MC
INDICATION TUBE
FL801
LED
Q826
7
17 MS
35 DRV ON
: CD DIGITAL OUT (OPTICAL)
DSDL
2
6
18 PSCK
PS 39
: SACD
1
SL
MUTE
Q301
SR
19 DSCK
30 TRAY IN
KEY
VOUTL 9
5
FWD 16
: CD
PLRCK VOUTR 10
3
MUTE12 19
• Signal Path
PBCK
5
IC430(1/2)
AMP
20 DBCK
EPR/B,
XEPCS,
XEWC,
EEPSO,
EEPSI,
EEPSCK
33 TRAY OUT
S841-845,
S851,855,
S861-865
3
A0-10,BA
REV 17
MUTE34 20
L MUTE
Q303
L MUTE 98
38 XLDON
25 DO6+
ANALOG
5.1CH OUT
MZR 94
IC708
16M SDRAM
219 SLDA
M
MUTE
Q501,502
74 SMUTE
SMUTE 61
IN4- 10
1
15 MD
52 JIT
JIT 226
31 DO3-
2
16 MC
72 XWRST
59 XRST
R
MUTE
IC400(2/2) Q401,402
AMP
17 MS
214 TDON
IN2- 4
OUT2 5
SLA+
70 XRD
L
VOUTR 10
18 PSCK
13,15-22 CA0-8 SLATR DAC 3
SCLK DAC 2
4-11 CD0-7
SDATA DAC 1
8
J351
7
19 DSCK
9
A0-8
6
20 DBCK
XWAIT 34
IN1+ 48
IC400(1/2)
AMP
DSAL 83
231 MIRR
MIRR 33
GND
FCS+
IC260
DAC
DSAR 84
VCI 39
4
DIGITAL
OUT
OPTICAL
1
PCMD1 96
TE 41
DSASW 90
24 LDSELO
PD
VR
D OUT
DOUT958 100
Q002
19
IC330
OPTICAL OUT
19 VC
RF
8
IC706
DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC001
RF AMP
3
1
MUTE REG
Q961
RECT
D960,961
RECT
D936,937
D971
S891
POWER
SCD-XE600
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Circuit Boards Location
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
LED board
PT board
POWER SWITCH board
RF board
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• Indication of transistor
C
Q
B E
These are omitted.
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : SACD PLAY
(
) : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : SACD
J : CD
c : CD DIGITAL OUT (OPTICAL)
KEY board
MAIN board
DISPLAY board
LOADING board
SCD-XE600
13
13
SCD-XE600
5-2.
PRINTED WIRING BOARD – RF BOARD –
• See page 13 for Circuit Boards Location.
: Uses unleaded solder.
RF BOARD (SIDE A)
RF BOARD (SIDE B)
OPTICAL
TRAVERSE
UNIT
(DBU-3)
A
MAIN BOARD
CN702
(Page 16)
M901
SPINDLE MOTOR
M902
SLED MOTOR
SCD-XE600
14
14
IC001
SCD-XE600
5-3.
SCHEMATIC DIAGRAM – RF BOARD – • See page 23 for Waveforms.
RF BOARD
C011
0.01
C001
0.01
C004
22
6.3V
C035 0.1
C044
10
16V
R037 12k
C033 0.001
C031 0.1
C028 0.1
C025 0.1
C022 0.1
R002 100
C032 0.1
C027 0.01
C002
0.01
C039
0.01
(Page 17)
CN001
24P
JL003
JL004
R045
220
JL005
JL006
R009
820
C016
C015
0.0047
JW001
0.0047
JW002
JL007
C019
560p
JL008
JL009
JL011
OPTICAL
TRAVERSE
UNIT
(DBU-3)
JL012
R003
100
JL013
C005
0.0022
C006
0.0022
C007
0.0022
CN002
31PIN
C043
0.1
IC001
SP3726A
JL010
R004
C047
0.1
C048
0.22
0
C008 0.0022
JL014
R052 0
JL015
R053
0
R054 0
JL016
R055 0
JL017
JW003
JL018
JW004
C046
JL020
R006
27k
JL021
JL022
R018
10k
C026
0.01
R008
33
R010
47k
C017
100
6.3V
R011
100
R023
33
R020
33
JL002
R013
10k
Q001
2SB1132-T100-QR
C034
0.022
R025
47k
C023
100 6.3V
R007
33
JL001
Q002
2SB1132-T100-QR
CN003
9P
JL025
JL026
L002
L001
JL024
D001
1SS355TE-17
C009
10
16V
C018
0.001
D004
1SS355TE-17
C024
0.001
C021
10
16V
JL027
JL028
JL029
JL030
JL031
SCD-XE600
15
C038 0.047
C036 0.047
JL023
15
R029
100
C040
150p
R038
2.2M
R005
100k
JL019
0.01
SCD-XE600
5-4.
PRINTED WIRING BOARDS – MAIN BOARD –
• See page 13 for Circuit Boards Location.
: Uses unleaded solder.
DISPLAY BOARD
CN801
(Page 21)
B
IC950
IC985
C
PT BOARD
CN102
(Page 21)
IC200
IC400
L
FRONT
IC920
R
IC230
IC702
L
IC430
SURR
R
IC320
CENTER
IC460
IC260
IC701
IC705
SUB WOOFER
IC703
IC712
IC706
DIGITAL (CD)
OUT OPTICAL
IC330
IC708
A
LOADING BOARD
RF BOARD
CN002
(Page 14)
CN151
5
S272
LOADING
IN
S271
LOADING
OUT
M
M151
(LOADING)
1
21
1-645-721-
SCD-XE600
16
16
(21)
ANALOG
5.1CH OUT
SCD-XE600
• See page 23 for IC Block Diagram.
C706
0.1
CL771
CL847
CL848
CL770
CL846
C714
220
4V
C762 0.1
CL844
0.1
C761
CL845
0.1
C759
CL842
CL841
CL838
CL839
CL840
CL836
CL843
C757
0.1
C755
0.1
CL837
R783
10k
CL835
SL798
C751
2.2k
R781 1k
CL723
C745
0.1
0.1
C746
0.1
C733
0.047
0.1
CL724
C788
STP702
XX
C749
CN702
31P
0.1
C754
220
4V
C789
0.1
C753
• See page 23 for Waveforms.
47k
SCHEMATIC DIAGRAM – MAIN BOARD (1/4) –
R782
5-5.
IC703
µPC2918T-E1
RB604
4.7k
SL897
0.1
C771
CL877
CL876
SL896
C736 0.1
CL721
CL875
CL874
TP713
RB603
470
SL774
C731
0.0047
C730
0.0047
C723
1
C726
0.001
C722
0.1
C727
0.0047
SL773
RF
BOARD
CN002
(Page 15)
C729
0.001
SL772
CL804
SL771
CL803
CL830
CL802
CL829
CL801
CL828
CL800
CL754
CL799
CL753
CL798
CL752
CL797
CL751
R752
0
RB602
1k
CL796
C769
0.1
0.1
C743
SL778
CL795
SL777
CL794
SL776
CL793
SL775
C742
C770
0.1
CL792
CL791
0.1
CL790
CL834
C768
0.1
CL833
CL832
CL831
IC706
CXD2754Q
256-QFP(0.4)
0.1
C741
RB617
470
CL789
CL788
CL873
CL787
CL767
C734
0.1
CL872
SL770
CL871
0.1
CL870
C740
CL786
CL827
CL826
C767
0.1
RB616
470
CL869
CL825
C739 0.1
C766 0.1
CL867
CL866
CL824
CL823
CL766
CL765
CL865
CL764
CL864
CL763
CL785
CL762
CL784
C765
0.1
C738 0.1
CL822
SL871
CL821
SL875
CL820
CL782
CL819
SL872
CL776
CL755
CL775
TP729
CL861
CL862
CL863
CL860
CL859
CL856
CL857
CL858
C760
CL854
CL855
CL852
CL853
CL850
CL851
SL856
SL845
TP715
SL848
CL849
SL840
SL841
SL843
SL839
SL837
C758 0.1
0.1
C756
TP714
SL800
C744
1
CL773
CL777
CL756
TP730
XX
(Page 18)
SCD-XE600
17
17
CL774
CL778
CL757
CL772
CL779
CL758
C763 0.1
CL759
0.1
CL780
C752 0.1
CL781
CL760
C750 1
CL761
CL737
RB613
10k
0.1
SL799
C737
C764
0.1
RB615
470
(Page 19)
SCD-XE600
5-6.
SCHEMATIC DIAGRAM – MAIN BOARD (2/4) – • See page 23 for IC Block Diagram.
• See page 25 for IC Pin Function Description.
(Page 17)
(Page 19)
CN703
13P
FB703
0UH
FB710
0UH
(Page 22)
RB612
10k
RB601
10k
RB607
10k
RB606
10k
FL606
0UH
C715
CL883
CL880
CL881
CL882
CL748
CL879
CL746
CL740
C713
100 16V
CL878
C721 0.1
(Page 20)
0.1
(Page 20)
R731
10k
R708
100
CL734
CL769
CL768
C712
0.1
CL731
C711
0.1
C748
0.1
CL891
IC705
HD6432238RN57TEV
CL890
CL889
CL888
D511
DAP202UT106
(Page 20)
CL733
CL732
C704 0.1
STP703
XX
R701 1k
CL743
CL708
C702 1
CL730
C705
0.1
C701
R703 10k
0.1
R702 10k
RB611
10k
C703
0.1
IC702
BR9040F-WE2
CL722
RB605
10k
CL726
SCD-XE600
18
18
SL790
SL792
SL757
SL759
SL753
SL751
SL749
CL747
SL746
CL742
CL745
CL741
SL742
CL894
CL739
CL892
CL893
CL738
SL732
CL725
SL730
R707
1k
CL736
CL709
CL710
CL735
IC701
M51957BFP-600C
SCD-XE600
5-7.
SCHEMATIC DIAGRAM – MAIN BOARD (3/4) –
CL712
CL727
C709
220
4V
CL713
C716
100
16V
CL711
STP701
XX
CL728
CL729
R861
270k
C815
0.015
C814
0.22
C793
0.1
R878
470k
(Page 20)
C825
0.0015
R858
120k
R877
470k
R860
680k
CL809
C796
100
16V
CL808
R831
10k
R840
CL807
R852
100k
100k
D509
DAP202UT106
C800 0.1
CN705
5P
RB610
47k
CL818
R897
470k
C832
0.0047
CL812
CL813
RB609
10k
R899
220k
C817
0.001
IC712
FAN8035L
R870
33k
C772 0.1
(Page 17)
R869
56k
SL891
C816
0.001
SL898
R866
33k
C775
0.1
R865
56k
R889
0
CL805
C776
0.1
R876
82k
R791 47
R895
56k
C828
0.068
C821
100p
CL806
SL895
R894
56k
SL894
SL892
C794
0.1
C795
100
16V
R846
56k
C787
0.1
R872
10k
R871
10k
R804
330
C819
1
C781
0.1
C785
220
4V
C782
0.1
C783
100
16V
IC708
HY57V161610ETP-7DR
TP733
XX
R880
100k
C804 0.1
R820 150k
R819
150k
(Page 18)
SCD-XE600
19
19
R853
56k
C813
0.033
R857
33k
CL814
C829 0.068
R893
110k
M151
CN151
5P
15k
C809
0.033
C779
0.1
C780
0.1
S272
C820
220p
SL893
C778
0.1
S271
R874
33k
R888
CL815
R886 82k
R806 10
C822
220p
C777
10p
R885
15k
R892
110k
C830
100p
SCD-XE600
5-8.
SCHEMATIC DIAGRAM – MAIN BOARD (4/4) –
• See page 23 for Waveforms.
• See page 23 for IC Block Diagram.
IC985
BA12FP-E2
C934
470
16V
C933
0.1
C953
0.1
D960
DAN202UT106
D936
C932 1SR154-400TE25
470
35V
D937
1SR154-400TE25
C954
470
10V
C935
1000
16V
D933
1SR154-400TE25
D931
1SR154-400TE25
(Page 19)
C901
0.01
IC950
BA50BC0FPE2
C324
1
C923 0.1
C325
100
6.3V
R330 22
22
Q961
DTC143TKAT146
C961
10
50V
C910 0.001
R963
1k
R323
1k
R961
R962
1k
ETP910
EARTH PLATE
D963
UDZSTE -173.0B
D923
1SR154-400TE25
D921
1SR154-400TE25
R322
0
IC320
SN74LVU04APWR
C920 0.01
D922
1SR154-400TE25
C322
15p
C321
15p
CN901
8P
C962 0.1
R321
1M
Q305
UN5116-TX
C281
2200p
X321
11.2896M
IC920
BA33BC0T
D924
1SR154-400TE25
(Page 22)
D971
1SR154-400TE25
R324
100
(Page 18)
D934
1SR154-400TE25
D961
DAN202UT106
1k
R328
C921
10000
10V
C924
470
10V
D932
1SR154-400TE25
Q303
UN5116-TX
CL301
C302
0.1
(Page 18)
C212
10
50V
Q301
UN5116-TX
C970
C305
0.1
C303
0.1
(Page 18)
RB301
4.7k
CL302
RB302
220k
SL215
Q971
2SB1260
SL216
C971
47
63V
SL217
R326 22
SL220
C406
47 25V
IC200
DSD1751DBQR
C405
0.1
C404
1
C504 1
C208 1
C206 1
C402
0.001
RB402
6.8k
C403
150p
C362
0.1
R407
100k
R975
33k
R977
100
R979
10k
R978
22k
C973
22
16V
100
R411
R409
220
Q401
2SC3624AT1L15L16
C972
10
50V
R976
100
Q402
2SC3624A-T
1L15L16
R404
3.3k
R504
3.3k
C502
0.001
R973
3.3k
D972
UDZSTE-17-33B
R408
330
C201
1000
6.3V
R972
10k
R971
10k
IC400(2/2)
NJM4565M(T
E2)
SL201
0.01
D973
UDZSTE-179.1B
D321
1SS357-TPH3
C931
10000
16V
RB410
2.2k
R507
100k
C503
150p
Q501
2SC3624AT1L15L16
RB502
6.8k
IC400(1/2)
NJM4565M(T
E2)
CL245
IC430(2/2)
NJM4565M(T
E2)
C534 1
C238 1
C236 1
SL231
CL275
C436
47
25V
33k
C433 150p
R202
C434 1
R201 10k
CL274
J351
6P
R509
220
R508
330
R511
100
0UH
C202
47
6.3V
IC230
DSD1751DBQR
C505
0.1
C506
47 25V
FB201
Q502
2SC3624A-T
1L15L16
C432
0.001
RB432
6.8k
C532
0.001
RB532
6.8k
R439
220
Q431
2SC3624AT1L15L16
C435
0.1
C364
0.1
C533
150p
C272
10
50V
R438
330
Q432
2SC3624AT1L15L16
R434
3.3k
R437
100k
R534
3.3k
R537
100k
Q532
2SC3624AT1L15L16
C535
0.1
C462
0.001
SL261
C562
0.001
CL868
C366
0.1
C463 150p
C464 1
IC260
DSD1751DBQR
C536
47
25V
C466
47
25V
C564
1
C266 C268
1
1
C351
0.1
CL202
Q531
2SC3624AT1L15L16
R468
330
C331
0.1
R469
220
C465
0.1
RB462
6.8k
RB562
6.8k
R464
3.3k
R467
100k
R564
3.3k
R567
100k
Q463
2SC3624A-T
1L15L16
Q462
2SC3624AT1L15L16
Q563
2SC3624A-T
1L15L16
SL262
CL201
RB442
2.2k
R539
220
R538
330
IC430(1/2)
NJM4565M(T
E2)
IC460(2/2)
NJM4565M(T
E2)
ANALOG
5.1CH OUT
RB441
2.2k
C565
0.1
C563
150p
IC460(1/2)
NJM4565M(T
E2)
C566
47
25V
Q562
2SC3624AT1L15L16
R569
220
R568
330
SCD-XE600
20
20
IC330
IC TOTX141L
CL244
C242
10
50V
SCD-XE600
5-9.
PRINTED WIRING BOARDS – DISPLAY, POWER SUPPLY SECTION –
B
• See page 13 for Circuit Boards Location.
: Uses unleaded solder.
MAIN BOARD
CN703
(Page 16)
MULTI CHANNEL DECODING
M
m
A
FLUORESCENT INDICATOR TUBE
IC801
. AMS >
PUSH ENTER
x
X
H
IC802
ROTARY ENCODER
POWER TRANSFORMER
C
TIME/TEXT
MAIN BOARD
CN901
(Page 16)
S891
POWER
AC IN
SCD-XE600
21
21
PLAY MODE
MULTI/2CH
SA-SD/CD
MENU
SCD-XE600
5-10. SCHEMATIC DIAGRAM – DISPLAY, POWER SUPPLY SECTION –
• See page 23 for Waveforms. • See page 27 for IC Pin Function Description.
C819
0.01
CN805
2P
R832
100
R862
2.2k
R861
1k
C831
47
6.3V
C832
0.01
S861
S862
S863
S864
S865
R841
1k
TP126
CN813
2P
IC802
NJL73H400A
R831
47
R826
10k
TP26
R842
2.2k
R843
2.2k
R844
4.7k
R845
10k
R819
10k
C804
0.1
R817 10k
R863
2.2k
R818 10k
R864
4.7k
R820
10k
S841
S842
S843
C816
0.001
0.01
R853
2.2k
R854
4.7k
S851
S855
ENCORDER
Q826
2SC3624AT1L15L16
C812
0.001
R858
82
CN804
2P
C813
0.001
IC801
mPD780232GC-706-8BT-A
R852
2.2k
S845
C817
C818 0.01
C803 0.1
R851
1k
S844
C811
0.001
R856
10k
FB801
FB
R857
10k
TP5
X801
5MHz
R805
10k
C802
0.1
C805
0.1
(Page 18)
C806
0.1
C801
100
6.3V
Q824
DTC114EKA
-T146
CN801
13P
Q821
DTC114EKA-T146
Q825
DTC114EKA
-T146
Q822
DTC114EKA-T146
R821
100k
R822
100k
Q823
DTC114EKA
-T146
C822
R823
0.001
100k
C823
0.001
R824
100k
C824
0.001
R825
100k
C825
0.001
C821
0.001
C827
0.1
C829
0.1
FL801
T101
MULTI
CHANNEL
DECODING
D801
SEL5E20C-STP15
BLUE
S891
C891
0.0022
250V
C101
0.0022
250V
CN101
2P
CN892
2P
CN891
2P
(Page 20)
CN102
8P
SCD-XE600
22
22
C833
0.1
R834
10k
CN814
2P
SCD-XE600
• Waveforms
• IC Block Diagrams
3.5 Vp-p
1.4 Vp-p
354 ns
500 mV/DIV, 200 ns/DIV
8
7
6
5
1 V/DIV, 100 ns/DIV
ADDRESS
DECODER
3
IC706 <z./ (RF IN)
(SACD play mode)
ADDRESS
BUFFER
HIGH VOLTAGE
GENERATOR
R/W
AMP
POWER
SUPPLY
VOLTAGE
DETECTOR
COMMAND DECODE
CONTROL CLOCK
GENERATION
DATA
REGISTER
1
500 mV/DIV, 40 ns/DIV
4
R/B
500 mV/DIV, 40 ns/DIV
2
3
4
SK
1.4 Vp-p
CS
1.4 Vp-p
WRITE
DISABLE
VCC
IC001 tl (SIGO)
(SACD play mode)
8bit
1
COMMAND
REGISTER
4096bit
EEPROM ARRAY
3.5 Vp-p
200 ns
1 V/DIV, 100 ns/DIV
BR9040F-WE2
DI
IC702
IC801 5 (IC)
DO
5
GND
IC706 uk (DSPHREFO)
16bit
2
– RF Board –
16bit
IC001 tl (SIGO)
(CD play mode)
– DISPLAY Board –
8bit
1
– MAIN Board –
WC
– RF Board –
IC320 2, 4, 6, q;, qs
– MAIN Board –
3.3 Vp-p
IC200, IC230, IC260
88.6 ns
DSD1751DBQR
1 V/DIV, 50 ns/DIV
DSDL 1
DSDR 2
DSD
I/F
20 DBCK
DSD
FILTER
MUX
PBCK 3
PDATA 4
MUX
PCM
I/F
PLRCK 5
PCM
FILTER
(X8 DF)
MULTI-LEVEL
DELTA-SIGMA
MODULATOR
DGND 6
VDD 7
VCC 8
VOUTL 9
VOUTR 10
19 DSCK
18 PSCK
17 MS
MODE
CONTROL
16 MC
15 MD
14 ZEROR/ZEROA
13 ZEROL/NA
ANALOG
LPF
MULTI-LEVEL
DAC
12 VCOM
11 AGND
SCD-XE600
23
23
SCD-XE600
DQ15
DQ14
VSSQ
DQ13
DQ12
VCCQ
DQ11
DQ10
VSSQ
DQ9
DQ8
VDDQ
NC
UDQM
CLK
CKE
NC
A9
A8
A7
A6
A5
A4
VSS
HY57V161610ETP-7DR
VSS
IC708
50
49 48
47
46 45
44
43 42
41
40 39
38
37
36 35 34
33
32 31 30 29 28 27
26
TIMING
REGISTER
OUTPUT
BUFFERS
PROGRAMING
REGISTER
READ
DATA
REGISTER
LATENCY
&
BURST
CONTROLLER
INTERNAL
COLUMN
ADDRESS
COUNTOR
SENSE
AMPLIFIER
VCC
OUT
C
7
6
5
1
2
3
4
IN
NC
GND
1.25V
–
+
24
11 12
13
14 15 16 17 18
19 20 21 22 23 24
25
A11-BA
A10/AP
A0
A1
A2
A3
VDD
RAS
CS
10
LDQM
WE
CAS
ROW
DECODERS
VDDQ
DQ4
DQ5
NC
8
NC
M51957BFP-600C
WORD
DRIVERS
DQ6
DQ7
8 9
– DISPLAY Board –
IC701
COLUMN
DECODERS
VSSQ
7
VCCQ
DQ2
DQ3
DQ0
DQ1
5 6
VSSQ
VDD
MEMORY
CELLS
4
INTERNAL
ROW
ADDRESS
COUNTOR
BANK
CONTROLLER
INPUT
BUFFERS
2 3
ROW
ADDRESS
BUFFERS
I/O
CONTROLLER
INPUT
DATA
REGISTER
1
COLUMN
ADDRESS
BUFFERS
SCD-XE600
• IC Pin Function Description
MAIN BOARD IC705 HD6432238RN57TEV (MASTER CONTROL)
Pin No.
Pin Name
I/O
Description
1
SDATA_DAC
O
Serial data output to the D/A converter
2
SCLK_DAC
O
Serial data transfer clock signal output to the D/A converter
3
SLATR_DAC
O
Serial data latch pulse output to the D/A converter
4 to 11
CD0 to CD7
I/O
12
CVCC
–
Power supply terminal (+3.3V)
13
CA0
O
Address signal output to the DSP
14
VSS0
–
Ground terminal
15 to 22
CA1 to CA8
O
Address signal output to the DSP
23, 24
PB1, PB2
O
Not used
25
LOAD_S0
I
Loading in switch input terminal
26
LOAD_S2
I
Detection signal input for disc tray open
27
LOAD_S1
I
Loading out switch input terminal
28
TSENS
I
Not used
29
DSENS
I
Disc in detection signal input terminal
30
TRAY_IN
O
Control signal for loading motor drive
31
RS232CTx
O
Not used
32
RS232CRx
I
Not used
33
TRAY_OUT
O
Control signal for loading motor drive
34
P10
O
Not used
35
DRV_ON
O
Stop signal output for the sled motor and focus/tracking coil
36
SP_ON
O
Stop signal output for the spindle motor
37
P13
O
Not used
38
XLDON
O
Laser diode on/off control signal output to the RF amplifier
39, 40
TRMP, TRMM
O
Tray motor control signal output terminal
41
P17
O
Not used
42
AVSS
–
Ground terminal
43
DIAG
I
Not used
44
P96
I
Not used
45 to 50
P47 to 42
I
Not used
51
MODEL
I
Setting terminal for model discrimination
52
JIT
I
Jitter value input from the DSP
Two-way data bus with the DSP
Not used
Not used
Not used
53
VREF
I
Reference voltage input terminal
54
AVCC
–
Power supply terminal (+3.3V)
55, 56
MD0, MD1
I
Setting terminal for the CPU operational mode
57
OSC2
O
Sub system clock output terminal
58
OSC1
I
Sub system clock input terminal
59
XRES
I
60
XNMI
I
61
XSTBY
I
Standby on/off control signal input terminal
62
VCC
–
Power supply terminal (+3.3V)
63
XTAL
–
System clock terminal (12.5 MHz)
64
VSS1
–
Ground terminal
65
EXTAL
I
System clock input terminal (11.2896 MHz)
66
FWE
I
Write enable signal input for flash memory
67
MD2
I
Setting terminal for the CPU operational mode
68
PF7
I
Not used
Not used
Not used
System reset signal input from the reset signal generator
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it
changes to “H”
Non-maskable interrupt signal input terminal
Not used
Not used
Not used
Not used
25
SCD-XE600
Pin No.
Pin Name
I/O
Description
70
XRD
O
Data read strobe signal output to the DSP
71
XWR
O
Write strobe signal output to the DSP
72
XWRST
O
Reset signal output to the DSP
73
XWAIT
I
Wait request signal input for bus cycle
74
SMUTE
O
Muting on/off control signal output to the DSP
75
EPR/B
I
Read/busy signal input from the EEPROM
76
XEPCS
O
Chip select signal output to the EEPROM
77
XEWC
O
WC signal output to the EEPROM
78
P32
O
Not used
79
EEPSO
O
Serial data output to the EEPROM
80
EEPSI
I
Serial data input from the EEPROM
81
EEPSCK
O
Serial data transfer clock signal output to the EEPROM
82
P36
O
Not used
83
IFSO
O
Serial data output to the display controller
84
IFSI
I
Serial data input from the display controller
85
IFSC
O
Serial data transfer clock signal output to the display controller
86
P74
O
Not used
87
XCS
O
Chip select signal output to the display controller
88 to 90
P72 to P70
I
Not used
91
XIFINT
I
Busy signal input from the display controller
92
XINT0
I
Interrupt request signal input from the DSP
26
93
PG2
I
Not used
94
MZR
I
Zero data (R-CH) flag detection signal input from the D/A converter
95
MZL
I
Zero data (L-CH) flag detection signal input from the D/A converter
96
XIFCS
O
Chip select signal output to the display controller
97
R_MUTE
O
Muting on/off control signal output terminal
98
L_MUTE
O
Muting on/off control signal output terminal
99
INIT_DAC
O
Not used
100
M/2
O
Muting on/off control signal output terminal
SCD-XE600
DISPLAY BOARD IC801 µPD780232GC-706-8BT (DISPLAY CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
VDD1
–
Power supply terminal (+3.3V)
2
VSS1
–
Ground terminal
3
X1
I
System clock input terminal (5 MHz)
4
X2
O
System clock output terminal (5 MHz)
5
IC
–
Not used
6
RESET
I
System reset signal input from the reset signal generator
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it
changes to “H”
7
P27/SCK1
I
Serial data transfer clock signal input from the master controller
8
P26/SI1
I
Serial data input from the master controller
9
P25/SO1
O
Serial data output to the master controller
10
P24/BUSY
I/O
Not used
11
P23
O
LED drive signal output terminal
12
ACK P22
O
Busy signal output to the master controller
13
P21/SO3
I/O
Not used
14
SCK3
I/O
Not used
15
REC P00/INTP0
I
16
P01/INTP1
I/O
17
SIRCS P02/TI
I
SIRCS signal input terminal
Chip select signal input from the master controller
Not used
18
AVSS
–
Ground terminal
19 to 21
ANI3 to ANI1
I
Front panel keys input terminal (A/D input)
22
ANI0
I
Key input terminal (A/D input)
23
VSS0
–
Ground terminal
24
AVDD
–
Power supply terminal (+3.3V)
Power supply terminal (+3.3V)
Not used
25
VDD0
–
26
TEST FIP52
I/O
Test mode setting terminal
27 to 44
FIP51 to FIP34
I/O
Not used
45 to 58
FIP33 to FIP20
O
Segments drive signal output to the fluorescent indicator tube
59
VDD2
–
Power supply terminal (+3.3V)
“L”: test mode, normally fixed at “H”
60
VLOAD
–
Pull down resistor connection terminal of VFD controller and driver
61 to 64
FIP19 to FIP16
O
Segments drive signal output to the fluorescent indicator tube
65 to 80
FIP15 to FIP0
O
Grid drive signal output to the fluorescent indicator tube
27
SCD-XE600
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Accessories are given in the last of the electrical parts list.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
6-1. MAIN SECTION
3
2
#1
10
2
12
#1
4
CD mechanism deck
section
(CDM66D-DVBU50)
6
11
5
T101
not supplied
8
7
#1
front panel section
not supplied
#1
9
1
#1
Ref. No.
Part No.
Description
1
2
3
4
* 5
4-255-243-21
3-363-099-11
4-232-580-91
1-862-181-11
3-703-244-00
PANEL LOADING
SCREW (CASE 3 TP2)
CASE (408226)
PT BOARD
BUSHING (2104), CORD
06
* 7
1-827-597-11 CORD, POWER
4-954-051-51 HOLDER, PC BOARD
28
Remark
Ref. No.
8
9
10
11
12
0 T101
#1
Part No.
Description
A-4752-595-A
X-2022-049-1
3-077-331-01
1-829-172-11
1-828-333-11
MAIN BOARD, COMPLETE
FOOT ASSY
+BV3 (3-CR)
WIRE (FLAT TYPE) (31 CORE)
WIRE (FLAT TYPE) (13 CORE)
1-443-403-11 TRANSFORMER, POWER
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
Remark
SCD-XE600
6-2. FRONT PANEL SECTION
not
supplied
56
56
not
supplied
(LED board)
56
57
54
56
56
55
56
56
53
not
supplied
59
not
supplied
60
51
52
Ref. No.
51
52
53
54
55
Part No.
Description
4-232-622-21
3-354-981-11
X-2022-056-1
4-255-244-21
1-862-182-11
KNOB (AMS)
SPRING (SUS), RING
PANEL, FRONT ASSY
BUTTON, POWER
POWER SWITCH BOARD
Remark
Ref. No.
56
57
59
60
Part No.
Description
3-087-053-01
1-862-179-11
A-4752-665-A
4-977-358-01
+BVTP2-6 (3CR)
KEY BOARD
DISPLAY BOARD, COMPLETE
CUSHION
Remark
29
SCD-XE600
6-3. CD MECHANISM DECK SECTION (CDM66D-DVBU50)
not supplied
208
not supplied
207
#2
209
206
205
204
optical pick-up section
(DVBU50)
210
M151
203
201
202
Ref. No.
Part No.
Description
201
202
203
204
205
4-227-899-01
1-645-721-11
4-231-530-05
4-232-712-01
4-232-710-01
SCREW (DIA. 12), FROATING
LOADING BOARD
TRAY (66)
CAM (66)
PULLEY (LD)
206
4-232-713-01 BELT (LD)
30
Remark
Ref. No.
Part No.
Description
207
208
209
210
M151
4-232-711-01
3-053-844-01
4-231-529-01
4-232-682-01
A-4604-363-A
GEAR (LD)
YOKE
CHASSIS (66)
CUSHION (66)
MOTOR (L) ASSY (LOADING)
#2
7-621-775-10 SCREW +B 2.6X4
Remark
SCD-XE600
6-4. BASE UNIT SECTION (DVBU50)
257
257
256
255
256
257
256
254
258
252
251
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
251
252
254
0 255
4-218-253-52
A-4750-527-A
4-240-953-05
1-478-637-31
SCREW (M2.6), +BTTP
RF BOARD, COMPLETE
HOLDER (66D)
OPTICAL TRAVERSE UNIT (DBU-3)
Remark
Ref. No.
256
257
258
Part No.
Description
Remark
3-053-847-31 INSULATOR
4-981-923-01 SCREW (M), STEP
1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)
31
SCD-XE600
SECTION 7
ELECTRICAL PARTS LIST
DISPLAY
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
Description
Remark
Ref. No.
Part No.
A-4752-665-A DISPLAY BOARD, COMPLETE
************************
< CAPACITOR >
C801
C802
C803
C804
C805
1-124-584-00
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
C806
C811
C812
C813
C816
1-165-319-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
50V
50V
50V
50V
50V
C817
C818
C819
C821
C822
1-162-970-11
1-162-970-11
1-162-970-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
25V
25V
25V
50V
50V
C823
C824
C825
C827
C829
1-162-964-11
1-162-964-11
1-162-964-11
1-165-319-11
1-165-319-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.1uF
0.1uF
10%
10%
10%
50V
50V
50V
50V
50V
C831
C832
1-124-589-11 ELECT
1-162-970-11 CERAMIC CHIP
47uF
0.01uF
20%
10%
16V
25V
20%
< CONNECTOR >
1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P
< FERRITE BEAD >
FB801
1-414-595-11 INDUCTOR, FERRITE BEAD
1-518-992-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC801
IC802
32
6-804-318-01 IC uPD780232GC-706-8BT-A
8-759-826-33 IC NJL73H400A
Description
6.3V
25V
25V
25V
25V
Q821
Q822
Q823
Q824
Q825
8-729-027-43
8-729-027-43
8-729-027-43
8-729-027-43
8-729-027-43
Q826
8-729-141-73 TRANSISTOR
Remark
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
2SC3624A-T1L15L16
< RESISTOR >
R805
R817
R818
R819
R820
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R821
R822
R823
R824
R825
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R826
R831
R832
R841
R842
1-216-833-11
1-216-805-11
1-216-809-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
47
100
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R843
R844
R845
R851
R852
1-216-825-11
1-216-829-11
1-216-833-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
4.7K
10K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R853
R854
R856
R857
R858
1-216-825-11
1-216-829-11
1-216-833-11
1-216-833-11
1-216-808-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
4.7K
10K
10K
82
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
< FLUORESCENT INDICATOR >
FL801
When indicating parts by reference
number, please include the board.
< TRANSISTOR >
4-949-935-41 CUSHION (FL)
CN801
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
S841
S842
S843
S844
S845
1-771-349-21
1-771-349-21
1-771-349-21
1-771-349-21
1-771-349-21
SWITCH, KEYBOARD (x)
SWITCH, KEYBOARD (H)
SWITCH, KEYBOARD (X)
SWITCH, KEYBOARD (m)
SWITCH, KEYBOARD (M)
S851
1-771-349-21 SWITCH, KEYBOARD (A)
SCD-XE600
DISPLAY
Ref. No.
S855
Part No.
Description
Remark
Ref. No.
1-478-268-11 ENCODER, ROTARY
(. AMS >, PUSH ENTER)
Part No.
1-862-179-11 KEY BOARD
**********
< CONNECTOR >
1-506-481-11 PIN, CONNECTOR 2P
< RESISTOR >
1-216-821-11
1-216-825-11
1-216-825-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
Description
Remark
< CAPACITOR >
X801
1-795-058-21 VIBRATOR, CERAMIC (5MHz)
*************************************************************
R861
R862
R863
R864
LED LOADING MAIN
A-4752-595-A MAIN BOARD, COMPLETE
*********************
< VIBRATOR >
CN813
KEY
1K
2.2K
2.2K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
C201
C202
C206
C208
C212
1-126-916-11
1-126-205-11
1-115-156-11
1-115-156-11
1-128-991-21
ELECT
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
1000uF
47uF
1uF
1uF
10uF
20%
20%
C236
C238
C242
C266
C268
1-115-156-11
1-115-156-11
1-128-991-21
1-115-156-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
10uF
1uF
1uF
20%
10V
10V
50V
10V
10V
C272
C281
C302
C303
C305
1-128-991-21
1-162-966-11
1-164-156-11
1-164-156-11
1-164-156-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
20%
0.0022uF 10%
0.1uF
0.1uF
0.1uF
50V
50V
25V
25V
25V
C321
C322
C324
C325
C331
1-162-917-11
1-162-917-11
1-115-156-11
1-126-206-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
15PF
15PF
1uF
100uF
0.1uF
50V
50V
10V
6.3V
25V
C351
C362
C364
C366
C402
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.001uF
C403
C404
C405
C406
C432
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C433
C434
C435
C436
C462
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C463
C464
C465
C466
C502
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C503
C504
C505
C506
C532
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C533
C534
C535
C536
C562
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C563
C564
C565
C566
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
150PF
1uF
0.1uF
47uF
5%
20%
6.3V
6.3V
10V
10V
50V
< SWITCH >
S861
1-771-349-21 SWITCH, KEYBOARD (MENU)
S862
1-771-349-21 SWITCH, KEYBOARD (SA-CD/CD)
S863
1-771-349-21 SWITCH, KEYBOARD (MULTI/2CH)
S864
1-771-349-21 SWITCH, KEYBOARD (PLAY MODE)
S865
1-771-349-21 SWITCH, KEYBOARD (TIME/TEXT)
*************************************************************
LED BOARD
**********
5%
5%
20%
5%
25V
25V
25V
25V
25V
< CAPACITOR >
C833
1-164-156-11 CERAMIC CHIP
0.1uF
25V
< CONNECTOR >
CN814
1-506-481-11 PIN, CONNECTOR 2P
< LED >
D801
6-500-647-01 LED SEL5E20C-STP15
(MULTI CHANNEL DECORDING)
< RESISTOR >
R834
1-216-833-11 METAL CHIP
10K
5%
1/10W
*************************************************************
1-645-721-11 LOADING BOARD
**************
< CONNECTOR >
* CN151
10%
20%
5%
50V
10V
16V
25V
25V
1-568-943-11 PIN, CONNECTOR 5P
< SWITCH >
S271
1-572-086-11 SWITCH, LEAF (LOADING OUT)
S272
1-572-086-11 SWITCH, LEAF (LOADING IN)
*************************************************************
10%
20%
5%
10%
20%
5%
10%
20%
5%
10%
20%
5%
10%
20%
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
33
SCD-XE600
MAIN
Ref. No.
Part No.
Description
Remark
C701
1-164-156-11 CERAMIC CHIP
0.1uF
C702
C703
C704
C705
C706
1-125-837-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
C709
C711
C712
C713
C714
1-126-246-11
1-164-156-11
1-164-156-11
1-117-681-11
1-126-246-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
220uF
0.1uF
0.1uF
100uF
220uF
20%
C715
C716
C721
C722
C723
1-164-156-11
1-117-681-11
1-164-156-11
1-107-826-11
1-125-837-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.1uF
0.1uF
1uF
10%
10%
25V
16V
25V
16V
6.3V
C726
C727
C729
C730
C731
1-162-964-11
1-162-968-11
1-162-964-11
1-162-968-11
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0047uF
0.001uF
0.0047uF
0.0047uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C733
C734
C736
C737
C738
1-165-176-11
1-107-826-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
16V
16V
25V
25V
25V
C739
C740
C741
C742
C743
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C744
C745
C746
C748
C749
1-115-156-11
1-107-826-11
1-164-156-11
1-164-156-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
0.1uF
0.1uF
0.1uF
C750
C751
C752
C753
C754
1-115-156-11
1-216-825-11
1-164-156-11
1-164-156-11
1-126-246-11
CERAMIC CHIP
METAL CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
1uF
2.2K
0.1uF
0.1uF
220uF
C755
C756
C757
C758
C759
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
C760
C761
C762
C763
C764
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
C765
C766
C767
C768
C769
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
C770
1-164-156-11 CERAMIC CHIP
0.1uF
25V
34
25V
20%
20%
20%
6.3V
25V
25V
25V
25V
4V
25V
25V
16V
4V
25V
25V
25V
25V
25V
10%
10%
5%
20%
10V
16V
25V
25V
16V
10V
1/10W
25V
25V
4V
Ref. No.
Part No.
Description
C771
C772
C775
C776
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
Remark
C777
C778
C779
C780
C781
1-162-915-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
0.1uF
0.1uF
0.1uF
0.1uF
C782
C783
C785
C787
C788
1-164-156-11
1-117-681-11
1-126-246-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
220uF
0.1uF
0.1uF
C789
C793
C794
C795
C796
1-164-156-11
1-164-156-11
1-164-156-11
1-117-681-11
1-117-681-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
100uF
100uF
C800
C804
C809
C813
C814
1-164-156-11
1-164-156-11
1-164-677-11
1-164-677-11
1-115-467-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.033uF
0.033uF
0.22uF
C815
C816
C817
C819
C820
1-164-245-11
1-162-964-11
1-162-964-11
1-115-156-11
1-164-816-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.015uF
0.001uF
0.001uF
1uF
220PF
10%
10%
10%
2%
25V
50V
50V
10V
50V
C821
C822
C825
C828
C829
1-162-927-11
1-164-816-11
1-162-965-11
1-110-563-11
1-110-563-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
220PF
0.0015uF
0.068uF
0.068uF
5%
2%
10%
10%
10%
50V
50V
50V
16V
16V
C830
C832
C901
C910
C920
1-162-927-11
1-162-968-11
1-162-970-11
1-162-964-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.0047uF
0.01uF
0.001uF
0.01uF
5%
10%
10%
10%
10%
50V
50V
25V
50V
25V
C921
C923
C924
C931
C932
1-128-546-11
1-164-156-11
1-126-935-11
1-126-939-11
1-126-951-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
10000uF
0.1uF
470uF
10000uF
470uF
20%
10V
25V
16V
16V
35V
C933
C934
C935
C953
C954
1-164-156-11
1-126-935-11
1-126-767-11
1-164-156-11
1-126-935-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.1uF
470uF
1000uF
0.1uF
470uF
C961
C962
C970
C971
C972
1-128-991-21
1-164-156-11
1-162-970-11
1-128-552-51
1-128-991-21
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT CHIP
10uF
0.1uF
0.01uF
47uF
10uF
10%
20%
20%
50V
25V
25V
63V
50V
C973
1-126-395-11 ELECT CHIP
22uF
20%
16V
25V
25V
25V
25V
0.5PF
20%
20%
50V
25V
25V
25V
25V
25V
16V
4V
25V
25V
20%
20%
25V
25V
25V
16V
16V
10%
10%
10%
25V
25V
16V
16V
10V
20%
20%
20%
20%
20%
20%
20%
25V
16V
16V
25V
16V
SCD-XE600
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
< CONNECTOR >
CN702
CN703
CN901
1-784-387-11 CONNECTOR, FFC/FPC 31P
1-793-989-21 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 13P
1-784-924-11 PIN, CONNECTOR 8P
< DIODE >
D321
D509
D511
D921
D922
8-719-027-76
8-719-941-09
8-719-941-09
8-719-053-18
8-719-053-18
DIODE
DIODE
DIODE
DIODE
DIODE
1SS357-TPH3
DAP202U
DAP202U
1SR154-400TE-25
1SR154-400TE-25
D923
D924
D931
D932
D933
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
D934
D936
D937
D960
D961
8-719-053-18
8-719-053-18
8-719-053-18
8-719-941-86
8-719-941-86
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
DAN202U
DAN202U
D963
D971
D972
D973
6-500-696-01
8-719-053-18
8-719-083-87
8-719-069-60
DIODE
DIODE
DIODE
DIODE
UDZSTE-173.0B
1SR154-400TE-25
UDZSTE-1733B
UDZSTE-179.1B
J351
1-785-536-11 JACK, PIN 6P (ANALOG 5.1CH OUT)
< TRANSISTOR >
Q301
Q303
Q305
Q401
Q402
8-729-924-04
8-729-924-04
8-729-924-04
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA143TU
DTA143TU
DTA143TU
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q431
Q432
Q462
Q463
Q501
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q502
Q531
Q532
Q562
Q563
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q961
Q971
8-729-027-56 TRANSISTOR
8-729-019-72 TRANSISTOR
DTC143TKA-T146
2SB1260
< RESISTOR >
1-216-833-11
1-216-839-11
1-216-857-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
33K
1M
0
1K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R324
R326
R328
R330
R404
1-216-809-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
22
22
22
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< IC >
R407
R408
R409
R411
R434
1-216-845-11
1-216-815-11
1-216-813-11
1-216-809-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
330
220
100
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
ETP910 1-537-771-21 TERMINAL BOARD, GROUND
< FERRITE BEAD >
1-500-283-11 INDUCTOR, FERRITE BEAD
1-414-595-11 INDUCTOR, FERRITE BEAD
1-414-595-11 INDUCTOR, FERRITE BEAD
< FILTER >
FL606
Remark
< JACK >
R201
R202
R321
R322
R323
< GROUND TERMINAL >
FB201
FB703
FB710
Description
1-234-177-21 FILTER, CHIP EMI
IC200
IC230
IC260
IC320
IC330
6-703-420-01
6-703-420-01
6-703-420-01
8-759-549-25
6-600-012-01
IC
IC
IC
IC
IC
DSD1751DBQR
DSD1751DBQR
DSD1751DBQR
SN74LVU04APWR
TOTX141L (DIGITAL (CD), OUT OPTICAL)
R437
R438
R439
R464
R467
1-216-845-11
1-216-815-11
1-216-813-11
1-216-827-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
330
220
3.3K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC400
IC430
IC460
IC701
* IC702
8-759-710-97
8-759-710-97
8-759-710-97
8-759-636-64
6-703-671-01
IC
IC
IC
IC
IC
NJM4565M-D
NJM4565M-D
NJM4565M-D
M51957BFP-600C
BR9040F-WE2
R468
R469
R504
R507
R508
1-216-815-11
1-216-813-11
1-216-827-11
1-216-845-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
220
3.3K
100K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC703
IC705
IC706
IC708
IC712
6-700-398-01
6-805-043-01
8-752-420-59
6-705-992-11
6-702-157-01
IC
IC
IC
IC
IC
uPC2918T-E1
HD6432238RN57TEV
CXD2754Q
HY57V161610ETP-7DR
FAN8035L
R509
R511
R534
R537
R538
1-216-813-11
1-216-809-11
1-216-827-11
1-216-845-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
100
3.3K
100K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC920
IC950
IC985
6-705-463-01 IC BA33BC0T
6-705-469-01 IC BA50BC0FP-E2
8-759-460-81 IC BA12FP-E2
R539
R564
R567
R568
1-216-813-11
1-216-827-11
1-216-845-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
3.3K
100K
330
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
35
SCD-XE600
MAIN
Ref. No.
POWER SWITCH
Part No.
PT
Description
Remark
Ref. No.
Part No.
Description
Remark
< COMPOSITION CIRCUIT BLOCK >
R569
1-216-813-11 METAL CHIP
220
5%
1/10W
R701
R702
R703
R707
R708
1-216-821-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10K
1K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB301
RB302
RB402
RB410
RB432
1-233-414-11
1-233-873-21
1-233-419-21
1-233-413-11
1-233-419-21
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
4.7K (3216)
220K (3216)
6.8K (3216)
2.2K (3216)
6.8K (3216)
R731
R752
R781
R782
R783
1-216-833-11
1-216-864-11
1-216-821-11
1-216-841-11
1-216-833-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
1K
47K
10K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
RB441
RB442
RB462
RB502
RB532
1-233-413-11
1-233-413-11
1-233-419-21
1-233-419-21
1-233-419-21
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
2.2K (3216)
2.2K (3216)
6.8K (3216)
6.8K (3216)
6.8K (3216)
R791
R804
R806
R819
R820
1-216-805-11
1-216-815-11
1-216-150-11
1-216-847-11
1-216-847-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
47
330
10
150K
150K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
RB562
RB601
RB602
RB603
RB604
1-233-419-21
1-236-908-11
1-233-412-11
1-233-577-11
1-233-414-11
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
6.8K (3216)
10K (3216)
1.0K (3216)
470 (3216)
4.7K (3216)
R831
R840
R846
R852
R853
1-216-833-11
1-216-845-11
1-216-842-11
1-216-845-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
56K
100K
56K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB605
RB606
RB607
RB609
RB610
1-236-908-11
1-236-908-11
1-236-908-11
1-236-908-11
1-233-578-11
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
10K (3216)
10K (3216)
10K (3216)
10K (3216)
47K (3216)
R857
R858
R860
R861
R865
1-218-883-11
1-216-846-11
1-216-855-11
1-216-850-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
120K
680K
270K
56K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB611
RB612
RB613
RB615
RB616
1-236-908-11
1-236-908-11
1-236-908-11
1-233-577-11
1-233-577-11
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
10K (3216)
10K (3216)
10K (3216)
470 (3216)
470 (3216)
R866
R869
R870
R871
R872
1-216-839-11
1-216-842-11
1-216-839-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
56K
33K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB617
1-233-577-11 RES, CHIP NETWORK
470 (3216)
R874
R876
R877
R878
R880
1-218-883-11
1-216-844-11
1-216-853-11
1-216-853-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
82K
470K
470K
100K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R885
R886
R888
R889
R892
1-216-835-11
1-216-844-11
1-216-835-11
1-216-864-11
1-218-896-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
15K
82K
15K
0
110K
5%
5%
5%
1/10W
1/10W
1/10W
0 C891
0.5%
1/10W
* CN891
R893
R894
R895
R897
R899
1-218-896-11
1-216-842-11
1-216-842-11
1-216-853-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
110K
56K
56K
470K
220K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R961
R962
R963
R971
R972
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R973
R975
R976
R977
R978
1-216-827-11
1-216-839-11
1-216-809-11
1-216-809-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
33K
100
100
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R979
1-216-833-11 METAL CHIP
10K
5%
1/10W
36
< VIBRATOR >
X321
1-795-535-21 VIBRATOR, CRYSTAL (11.2896MHz)
*************************************************************
1-862-182-11 POWER SWITCH BOARD
********************
< CAPACITOR >
1-113-920-11 CERAMIC
0.0022uF 20%
250V
< CONNECTOR >
1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P
< SWITCH >
0 S891
1-762-581-11 SWITCH, AC POWER PUSH (1 KEY) (POWER)
*************************************************************
1-862-181-11 PT BOARD
********
< CAPACITOR >
0 C101
1-113-920-11 CERAMIC
0.0022uF 20%
250V
< CONNECTOR >
* CN101 1-568-226-11 PIN, CONNECTOR (3.96mm PITCH) 2P
*************************************************************
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
SCD-XE600
RF
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Q001
Q002
< CAPACITOR >
C001
C002
C004
C005
C006
1-107-726-91
1-107-726-91
1-124-778-00
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
22uF
0.0022uF
0.0022uF
10%
10%
20%
10%
10%
16V
16V
6.3V
50V
50V
C007
C008
C009
C011
C015
1-162-966-11
1-162-966-11
1-124-779-00
1-107-726-91
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
10uF
0.01uF
0.0047uF
10%
10%
20%
10%
10%
50V
50V
16V
16V
50V
C016
C017
C018
C019
C021
1-162-968-11
1-126-206-11
1-115-416-11
1-164-739-11
1-124-779-00
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.0047uF
100uF
0.001uF
560PF
10uF
10%
20%
5%
5%
20%
50V
6.3V
25V
50V
16V
C022
C023
C024
C025
C026
1-107-826-11
1-126-206-11
1-115-416-11
1-107-826-11
1-107-726-91
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.001uF
0.1uF
0.01uF
10%
20%
5%
10%
10%
16V
6.3V
25V
16V
16V
C027
C028
C031
C032
C033
1-107-726-91
1-107-826-11
1-107-826-11
1-107-826-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
50V
C034
C035
C036
C038
C039
1-164-227-11
1-107-826-11
1-165-176-11
1-165-176-11
1-107-726-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.1uF
0.047uF
0.047uF
0.01uF
10%
10%
10%
10%
10%
25V
16V
16V
16V
16V
C040
C043
C044
C046
C047
1-164-217-11
1-107-826-11
1-124-779-00
1-107-726-91
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
0.1uF
10uF
0.01uF
0.1uF
5%
10%
20%
10%
10%
50V
16V
16V
16V
16V
C048
1-127-715-11 CERAMIC CHIP
0.22uF
10%
16V
< CONNECTOR >
CN001
CN002
CN003
Remark
8-729-903-46 TRANSISTOR
8-729-903-46 TRANSISTOR
2SB1132-P
2SB1132-P
< RESISTOR >
R002
R003
R004
R005
R006
1-216-809-11
1-216-809-11
1-216-864-11
1-216-845-11
1-216-838-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
100
100
0
100K
27K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R007
R008
R009
R010
R011
1-216-803-11
1-216-803-11
1-216-820-11
1-216-841-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33
33
820
47K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R013
R018
R020
R023
R025
1-216-833-11
1-216-833-11
1-216-803-11
1-216-803-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
33
33
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R029
R037
R038
R045
R052
1-216-809-11
1-216-834-11
1-216-861-11
1-216-813-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
100
12K
2.2M
220
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R053
1-216-864-11 SHORT CHIP
0
R054
1-216-864-11 SHORT CHIP
0
R055
1-216-864-11 SHORT CHIP
0
*************************************************************
MISCELLANEOUS
**************
06
11
12
0 255
258
1-827-597-11
1-829-172-11
1-828-333-11
1-478-637-31
1-824-106-12
CORD, POWER
WIRE (FLAT TYPE) (31 CORE)
WIRE (FLAT TYPE) (13 CORE)
DEVICE, OPTICAL (DBU-3)
CABLE, FLEXIBLE FLAT (24 CORE)
M151
A-4604-363-A MOTOR (L) ASSY (LOADING)
0 T101
1-443-403-11 TRANSFORMER, POWER
*************************************************************
ACCESSORIESE
*************
1-815-031-11 CONNECTOR, FFC/FPC (ZIF) 24P
1-784-879-21 CONNECTOR, FFC (LIF (NON-ZIF)) 31P
1-784-861-21 CONNECTOR, FFC (LIF (NON-ZIF)) 9P
< DIODE >
D001
D004
Description
< TRANSISTOR >
A-4750-527-A RF BOARD, COMPLETE
*******************
1-478-636-11 REMOTE COMMANDER (RM-SX800)
1-790-735-12 CORD, CONNECTION (Audio Connecting Cord)
2-021-059-61 MANUAL, INSTRUCTION
(ENGLISH, TRADITIONAL CHINESE)
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< IC >
IC001
6-703-445-01 IC SP3726A
< COIL >
L001
L002
1-412-031-11 INDUCTOR
1-412-031-11 INDUCTOR
47uH
47uH
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
37
SCD-XE600
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
1.0
2
Date
2004.10
Description of Revision
New