Download SLV-798HF/998HF

SLV-798HF/998HF
RMT-V229/V232C
SERVICE MANUAL
US Model
SLV-798HF/998HF
Canadian Model
SLV-798HF/998HF
G
j
Chilean Model
Mexican Model
PX Model
SLV-998HF
Photo : SLV-998HF
• Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENT for MECHANICAL ADJUSTMENTS.
(9-921-647-11)
S MECHANISM
SPECIFICATIONS
VIDEO CASSETTE RECORDER
MICROFILM
DIFFERENT SPECIFICATIONS
MODEL
SPECIFICATIONS
FLYING ERASE HEAD
BODY COLOR
REMOTE COMMANDER
SLV-798HF
SLV-998HF
—
BUILT-IN
BLACK
BLACK
RMT-V232C
RMT-V229
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
—2—
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
7.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the
customer.
Check the B+ voltage to see it is at the values specified.
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
2.
3.
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
—3—
A commercial leakage tester, such as the Simpson 229 or RCA
TW-540A. Follow the manufacturers' instructions to use these
instruments.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
TABLE OF CONTENTS
SERVICE NOTE
1.
2.
2-1.
2-2.
ERROR CODE INDICATION ··········································· 6
HOW TO REPLACE A ROTARY UPPER DRUM ··········· 7
HOW TO REMOVE A ROTARY UPPER DRUM ············ 7
HOW TO ATTACH A NEW ROTARY UPPER DRUM ···· 7
1.
GENERAL
Getting Started
Unpacking ·············································································· 1-1
Setting up the remote commander ········································· 1-1
Hookups ················································································· 1-1
Selecting a language ······························································ 1-7
Setting the clock ···································································· 1-7
Setting up cable box control ·················································· 1-9
Presetting channels ······························································ 1-10
Setting up VCR Plus+ ·························································· 1-11
Basic Operations
Playing a tape ······································································· 1-12
Recording TV programs ······················································ 1-13
Recording TV programs using VCR Plus+ ························· 1-14
Setting the timer manually ··················································· 1-14
Additional Operations
Playing/searching at various speeds ···································· 1-15
Searching for a selected point on the tape ··························· 1-16
Skip-searching automatically ··············································· 1-16
Recording TV programs using the quick timer ··················· 1-16
Checking/changing/cancelling timer settings ······················ 1-17
Recording stereo and bilingual programs ···························· 1-17
Adjusting the picture ··························································· 1-18
Changing menu options ······················································· 1-18
Editing with another VCR ··················································· 1-18
Additional Information
General setup information ··················································· 1-19
Index to parts and controls ··················································· 1-19
2.
DISASSEMBLY
2-1. UPPER CASE,
FRONT PANEL BLOCK ASSEMBLY ·························· 2-1
2-2. FR-130 BOARD, DM-74 BOARD ································· 2-1
2-3. REAR PANEL ································································· 2-1
2-4. POWER BLOCK, MA-318 BOARD
(WITH S MECHANISM DECK) ··································· 2-2
2-5. S MECHANISM DECK ················································· 2-2
2-6. INTERNAL VIEWS ························································ 2-3
2-7. INTERNAL VIEWS ························································ 2-4
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
OVERALL BLOCK DIAGRAM ···································· 3-1
VIDEO BLOCK DIAGRAM ·········································· 3-3
SERVO/SYSTEM CONTROL BLOCK DIAGRAM ····· 3-5
AUDIO BLOCK DIAGRAM ·········································· 3-7
MODE CONTROL BLOCK DIAGRAM ······················· 3-9
TUNER BLOCK DIAGRAM ······································· 3-11
POWER SUPPLY BLOCK DIAGRAM ······················· 3-13
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS ············································ 4-2
• MA-318
(REC/PB AMP, VIDEO, SERVO/SYSTEM CONTROL,
AUDIO, TUNER)
PRINTED WIRING BOARD ························· 4-2
• MA-318 (REC/PB AMP) SCHEMATIC DIAGRAM ·· 4-5
• MA-318 (VIDEO, NORMAL AUDIO)
SCHEMATIC DIAGRAM ······························ 4-8
• MA-318 (SERVO/SYSTEM CONTROL)
SCHEMATIC DIAGRAM ···························· 4-11
• MA-318 (ON SCREEN DISPLAY)
SCHEMATIC DIAGRAM ···························· 4-15
• MA-318 (DSF) SCHEMATIC DIAGRAM ················ 4-17
• MA-318 (V-SET) SCHEMATIC DIAGRAM ············ 4-19
• MA-318 (AFM AUDIO)
SCHEMATIC DIAGRAM ···························· 4-21
• MA-318 (TUNER) SCHEMATIC DIAGRAM ·········· 4-23
• MA-318 (POWER SUPPLY, AV-BUS)
SCHEMATIC DIAGRAM ···························· 4-25
• FR-130 (MODE CONTROL)
PRINTED WIRING BOARD ······················· 4-27
• FR-130 (MODE CONTROL)
SCHEMATIC DIAGRAM ···························· 4-29
• DM-74 (OPERATION SWITCHES)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ···························· 4-31
• JK-159 (LINE-2 IN)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ···························· 4-33
• POWER BLOCK SR801 (SWITCHING REGULATOR)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ···························· 4-35
• POWER BLOCK SR709 (SWITCHING REGULATOR)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ···························· 4-37
5.
INTERFACE, IC PIN FUNCTION
DESCRIPTION
5-1. SYSTEM CONTROL —
VIDEO BLOCK INTERFACE
(MA-318 BOARD IC161) ··············································· 5-1
5-2. SYSTEM CONTROL —
SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-318 BOARD IC161) ··············································· 5-1
5-3. SYSTEM CONTROL —
MECHANISM INTERFACE
(MA-318 BOARD IC161) ··············································· 5-2
5-4. SYSTEM CONTROL —
SYSTEM CONTROL PERIPHERAL
CIRCUIT INTERFACE (MA-318 BOARD IC161) ······· 5-2
5-5. SYSTEM CONTROL —
AUDIO BLOCK INTERFACE
(MA-318 BOARD IC161) ··············································· 5-2
5-6. SERVO/SYSTEM CONTROL MICROPROCESSOR
PIN FUNCTIONS (MA-318 BOARD IC161) ················ 5-3
5-7. TUNER/TIMER MODE CONTROL PIN FUNCTIONS
(FR-130 BOARD IC460) ················································ 5-4
6.
ADJUSTMENTS
6-1 MECHANICAL ADJUSTMENTS ································· 6-1
6-2. ELECTRICAL ADJUSTMENTS ··································· 6-1
2-1. PREPARATION BEFORE ADJUSTMENT ··················· 6-1
2-1-1. Equipment Required ························································ 6-1
2-1-2. Equipment Connection ···················································· 6-1
2-1-3. Input Signal Check ·························································· 6-1
2-1-4. Alignment Tape ······························································· 6-1
2-1-5. Input/Output Levels and Impedance ······························· 6-2
2-1-6. Adjustment Sequence ······················································ 6-2
2-2. POWER SUPPLY CHECK ············································· 6-2
2-2-1. Output Voltage Check (MA-318 Board) ························· 6-2
2-3. SERVO SYSTEM CHECK ············································· 6-3
2-3-1. RF Switching Position/
AF Switching Position Adjustments (MA-318 Board) ··· 6-3
2-4. VIDEO SYSTEM CHECKS AND ADJUSTMENT ······· 6-4
2-4-1. X’tal OSC Check (MA-318 Board) ································· 6-4
—4—
2-4-2. SYNC AGC Check (MA-318 Board) ······························ 6-4
2-4-3. Recording Y Level Check (MA-318 Board) ··················· 6-4
2-4-4. Recording Chroma Level Check (MA-318 Board) ········· 6-5
2-4-5. Playback Level Check (MA-318 Board) ························· 6-5
2-5. AUDIO SYSTEM ADJUSTMENT ································· 6-5
2-5-1. ACE Head Adjustment ···················································· 6-5
2-5-2. E-E Output Level Check ················································· 6-5
2-5-3. Overall Output Level and Distortion Factor Check ········· 6-6
2-5-4. Overall Noise Level Check ·············································· 6-6
2-6. TUNER SYSTEM ADJUSTMENT ································ 6-6
2-6-1. Separation Adjustment (MA-318 Board) ························ 6-6
2-7. ADJUSTING PARTS LOCATION DIAGRAM ············· 6-8
7.
REPAIR PARTS LIST
7-1. EXPLODED VIEWS ······················································ 7-1
7-1-1. FRONT PANEL ASSEMBLY AND UPPER CASE
SECTION ········································································ 7-1
7-1-2. CHASSIS SECTION ······················································· 7-2
7-1-3. MECHANISM DECK-1 ················································· 7-3
7-1-4. MECHANISM DECK-2 ················································· 7-4
7-1-5. MECHANISM DECK-3 ················································· 7-5
7-2. ELECTRICAL PARTS LIST ·········································· 7-6
—5—
SLV-798HF/998HF
SERVICE NOTE
1. ERROR CODE INDICATION
• Error codes are indicated using the lower 5 digits in the fluorescent display tube.
“At this time, Colon “:” between character is not indicated.”
Mode code indication when the error has occurred.
Error code
ERROR CODE
0 No error
1 Cam encoder error Loading direction
2 Cam encoder error Unloading direction
3 T reel error
4 S reel error
5 Capstan error
6 Drum error
7 Error on initializing
8 Cassette loading error
9 Reserve
MODE CODE
0 Power-on eject
1 Power-on initial
2 Power-off eject
3 Power-off stop
4 FF
5 REW
6 REC
7 REC- pause
8 Power-on stop
9 PB
10
11
12
13
14
15
16
17
18
19
FWD x1
FWD x2
CUE
PB-pause
RVS-pause
RVS x1
RVS x2
REV
Power-off initial
Mecha. error (Power off)
—6—
20
21
22
23
24
25
26
27
28
REW play
Cas. loading
Tape loading
Power-off loading
Mecha. error (Power on)
Power-on eject initial
Power-off eject initial
APC REC
Cas. loading
(No auto PB check)
2.
HOW TO REPLACE A ROTARY
UPPER DRUM
See below for note.
2-1.
1)
2)
3)
HOW TO REMOVE A ROTARY UPPER DRUM
Remove screw 1 (+P3 × 8) and remove the ground shaft
assembly 2. (Refer to Fig. 4.)
Remove soldering which is marked by arrow and remove the
rotary upper drum board completely.
Remove two screws 3 (PSW3 × 8) and remove the rotary
upper drum in the direction of A. (Refer to Fig. 5.)
If removal is difficult, remove it while rotating it slowly.
Note: If removal is difficult, check again if soldering is removed
completely.
2 Ground shaft assembly
1 Screw (+P3 × 8)
Soldering
2-2.
1)
2)
3)
Soldering
Pay attention so that finger print or like must not be put when
inserting a new upper drum into lower drum.
Align mark of the rotary upper drum board with the mark of
the rotary transformer board so that the screw hole on the upper
drum and that on the lower drum are aligned. (Refer to Fig. 5.)
If attaching is difficult, attach a upper drum while rotating it
slowly.
Note: Pay attention not to damage the video heads.
Confirm that the upper drum is inserted completely.
4)
5)
Drum when viewed
from the top
HOW TO ATTACH A NEW ROTARY UPPER
DRUM
Tighten the two screws 3 (PSW3 × 8). (Refer to Fig. 5.)
Fix the earth shaft 2 by tightening the screw 1 (+P3 × 8) so
that protrusion at the tip of the earth shaft contacts the center
of the drum shaft.
Note: When attaching the ground shaft assembly 2, never give
force to the plate spring 4.
4 Plate
spring
3 PSW3 × 8
Upper drum assembly
DZR-51-R (8-848-594-02)
(998HF)
DZR-45-R (8-848-576-02)
(EXCEPT 998HF)
A
Align the two arrow marks.
Fig. 4
Lower drum assembly
DZL-51B/J-RP (8-848-666-11)
Fig. 5
Note : There are two types of drum assembly built in models.
UPPER DRUM ASSEMBLY
DZR-51-R (998HF)
(8-848-594-02)
DZR-45-R (Except 998HF)
(8-848-576-02)
DRUM ASSEMBLY
DZH-96A-R (998HF)
(8-839-046-02)
DZH-94A/Z-RP (Except 998HF)
(8-839-044-02)
—Top View—
—Top View—
There are two printed circuit boards
on the top.
There is no printed circuit board.
[Discrimination]
Note: It cannot be divided to two parts, the upper and
the lower drum assemblies.
—7—
SECTION 1
GENERAL
1-1
SLV-798HF/998HF
This section is extracted from the
SLV-998HF instruction manual.
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20E
SLV-798HF/998HF
SECTION 2
DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE, FRONT PANEL BLOCK ASSEMBLY
1 Screws (case)
Upper case
3 Connector
From CN423 on
MA-318 board
2
4 Hooks
1 Screws (case)
3 Flat cable
From CN162 on
MA-318 board
5 Front panel
block assembly
4 Hooks
4 Hooks
2-2. FR-130 BOARD, DM-74 BOARD
5 JK insulated plate
3 Flat cable
2 FR-130 board
From CN140 on
FR-130 board
1 Screws (B2.6 × 8)
6 Screw (B2.6 × 8)
1 Screws (B2.6 × 8)
7 JK ground plate
4 Screw (B2.6 × 8)
2 DM-74 board
8 JK-159 board
Front panel assembly
3 Frexible board
From CN441 on
DM-74 board
2-3. REAR PANEL
2 Hooks
2 Hooks
2 Hooks
3 Rear panel
2 Hooks
1 Release cable stopper
from rear panel
2-1
2-4. POWER BLOCK, MA-318 BOARD (WITH S MECHANISM DECK)
Connector
(From CN201 on power block)
2 Screws
a
3 Power block
1
4 Screws
5 MA-318 board
(with S mechanism deck)
1
a
2-5. S MECHANISM DECK
1 Flexible board
From CN260 on
MA-318 board
2 Screws
4 Screws
S mechanism deck
5
MA-318 board
MD base (R)
MD base (M)
MD base (R)
2-2
2-6. INTERNAL VIEWS
— Top View —
M901 (Note)
Upper drum assembly DZR-45-R
8-848-576-02 (Except 998HF)
Upper drum assenbly DZR-51-R
Note : See page 7 for the note about drum
8-848-594-02 (998HF)
assembly.
Lower drum assembly DZL-51B/J-RP
8-848-666-11
Drum Assembly DZH-94A/Z-RP (Except 998HF)
8-839-044-02
Drum Assembly DZH-96A-R (998HF)
8-839-046-02
ACE head block assembly
A-6759-620-A
Pinch press block assembly
A-6759-615-A
FE head
1-500-144-11
FL complete assembly
A-6759-619-C
Reel (T) table
3-977-508-01
Reel (S) table
3-977-507-01
— Bottom View —
M902
DC motor (capstan)
1-698-971-11
M901 (Note)
Lower drum assembly
DZL-51B/J-RP
8-848-666-11
Rubber belt
3-977-510-01
M903
Cam motor assembly
X-3947-577-1
2-3
2-7. INTERNAL VIEWS
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
2-4E
SLV-798HF/998HF
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
(SEE PAGE 4-5, 8, 11, 15, 17, 19, 21, 23, 25)
AFC
IC871
VD
SYNC
DET/SET
MEDIA VIDEO
LINE 1
IN
L VIDEO 1
VIDEO
TUNER/MOD/IF
4CH
R
S701
SI 0
RF CH
SO 0
SCK 0
DRUM MOTOR
IC161
IC100
SYSTEM
CONTROL
TV/VTR
DRUM
SERVO
D VS
M
PLL CLOCK
D PG
DRUM
PG
D FG
DRUM
FG
AFT
Q VD
Q VD
I2C DATA VIDEO
SP
CH 2
IC260
REC Y/C
IC202
VIDEO
REC/PB
QAMP
C ROT
1H
DELAY
EP
CH 1
EP
CH 2
V SET CS
I2C CLOCK VIDEO
PB Y/C
SP
CH 1
CAPSTAN
SERVO
CAPSTAN MOTOR
IC100
CAP VS
C SYNC
C SYNC
S OUT 1
S CLK 1
S OUT 1
S CLK 1
RF SWP
RF SWP
RF ENV
RF ENV
M
CAP FG
FM PB
CH 1
IC340
IC140
CTL REC/PB
AFM
REC/PB
QAMP
CH 2
AUDIO
PROCESSOR
(HIFI)
AF REC
AF SWP
REC P
L
LINE 1
IN
RF AUDIO
IC733
TU L
M
MODE1-4
SAP,STEREO
LOADING
MOTOR
ROTARY
SWITCH
I2C DATA 1
I2C CLOCK 1
AF ENV
AF ENV
AF SWP
AF SWP
T REEL FG
SW12V
PH102
T REEL
T831,Q830
BIAS
ERASE
OSC
988HF ONLY
(SEE PAGE 4-33)
NORM OUT
S REEL FG
NORM IN
FULL
ERASE
HEAD
LOADING
MOTOR
F MONO,MAIN/SAP
ST/BILNG
PROCESSOR
I2C CLOCK 1
L 1(R)
R
CAM +,-
MPX
I2C DATA 1
AUDIO
CTL
AMP
IC101
AR
TU R
L 1(L)
IC141
CTL
AMP
AL
IC360
FM REC
CAPSTAN
MOTOR
CAPSTAN
FG
AUDIO
HEAD
CJ570
DRUM
MOTOR
PLL DATA
PLL ENB
TU VIDEO
VIDEO
HEAD
TU700
RF
3CH
AUDIO
H DET
CJ570
LINE
OUT
L
HD
Y/C
PROCESSOR
CJ570
AFT
SCK 0
IC501
(1/2)
SO 0
OUT
MPX
IC201
VIDEO
RF AUDIO
OSD
L VIDEO 2
VIDEO
VHF/
UHF
Q560
RF VIDEO
CJ801
LINE 2
IN
IN
IC500
VIDEO
TU VIDEO
MA-318 BOARD
JK-159
BOARD
RF VIDEO
(SEE PAGE 4-33)
PH101
S REEL
SIGNAL
CONTROL
T SENS
JK-159
BOARD
CJ801
Q101
T SENS
(2/2)
AUDIO
PROCESSOR
(MONO)
L 2(L)
L
LINE 2
IN
IC201
D103
(T/S LED)
S SENS
AF REC
AUDIO
L 2(R)
R
Q102
S SENS
AF SWP
Q103
REC P
T/S LED
FE ON
LED
DRIVE
IC980
IC403
REC/
PB
A HEAD REC
NORMAL
AUDIO
CNJ981
IN
A HEAD PB
VIDEO
AMP
NICOLON
CDC POWER
CABLE BOX
CONTROL/
CNJ980 CONTROL S
OUT
SIRCS
CBC I/O
T331,Q330
BIAS
ERASE
OSC
ERASE
HEAD
FR-130 BOARD
FULL
ERASE
HEAD
(SEE PAGE 4-29)
ND420
EXCEPT 998HF
IC461
SI 0
SO 0
T931,Q930
FULL
ERASE
HEAD
SCK 0
BIAS
ERASE
OSC
FLUORESCENT
INDICATOR TUBE
REMOTE
CONTROL
RECEIVER
SIRCS IN
IC460
FULL ERS
-F
+F
SIRCS OUT
988HF ONLY
MODE
CONTROL
IC462
EEPROM
998HF ONLY
IC463
S403-406,409,410
(SEE PAFE 4-32)
S407,408
POWER
FAIL DET
RESET
PULSE GEN
SI 0
SO 0
SCK 0
VSET CS
H DET
16
3-1
3-2
A/D0-2
FUNCTION
KEY
A/D3
FUNCTION
KEY
DM-74
BOARD
S441-443
S411,412
DMS1,2
PAUSE
FUNCTION
KEY
DMS
BLOCK
SLV-798HF/998HF
3-2. VIDEO BLOCK DIAGRAM
CJ570
MA-318 BOARD
(SEE PAGE 4-5, 8, 15, 17, 19)
Q502
BUFFER
IC501 !º REC/PB
Q560
LINE
OUT
BUFFER
VIDEO
Q503
IC871
503.5kHz
0.65Vp-p
Q871,872
Q875
VIDEO
AMP
IC500 3, @∞ REC/PB
BUFFER
IC501
AFC
IC201 #• REC/PB
(SEE PAGE 4-33)
LINE 2
IN
IC201
(1/2)
L2 V
VIDEO
CN423
1
Y/C 1
1
FROM/TO
TUNER
BLOCK
TU700 36
Y/C 2
TU V
(SEE PAGE 3-12)
Y/C 3
30
CLP
32
CLP
28
L206
R
CLP
VIDEO
AMP
QH/QV
INS
P
P
4Vp-p
SEP
3
11
SP
CH1
SW5V
IC260
H
VIDEO REC/PB AMP
2
DET 8
IC871 #º REC/PB
(1/2)
H SUNC 12
V SET CS
CN162 18
IRQ 32
SYS RESET CN162 20
31
X871
HPF
CN162 2
CG CS
CN164 12
CG V
CN164 23
S IN 23
P
5
1H
DL
CS 24
V SYNC 11
BUFFER
7
Q211
R
12
FROM/TO
SYSCON
BLOCK
BUFFER
CLK 10
Q VD
33
200mV/Div
FSC
BPF
46
ENV
DET
IC201 $∞ PB
26
PB
EP
CH1
C ROT
14
COMP
PB
11
13
EP
CH2
C SYNC
LOGIC
SW10 SW6
8
DATA
CLOCK
10
RF SWP
SW9 SW5
12
IC202
21
18
R
19
R
20
4
ACC
AMP
P
17
R
PB RF
22
BUFFER
15
PB Y/C
BPF
P
MAIN
COMV.
DL
EQ
50
1
48
3
Q210
1H
DL
13
BUFFER
R
P
52
R
P
Q208
C
LPF
R
Q260
REC
IDEL
25
P
KIL
DE
EMPH.
26
R,A
B
VXO1
56
55
CLP
C
TRAP
AGC
24
27
REC
VCA
REC RF
Q801
Q805
BUFFER
SP
SW
SW2
28
Q201
Q802,803
BUFFER
PB RF
EQ AMP
30
CN261
1
CHECK
PIN
2
3
Q851-854
Q855-857
CLAMP
WAVE
SHAPER
S
Q810
BUFFER
Q809
N
FM
AGC
H
DEM
340mVp-p
H
3.579545MHz
500mVp-p
0.23Vp-p
IC201 @∞ REC
20
SERIAL
DECODER
SW
H
18
Q810 E PB
Q802 B PB
IC201 $• PB
IC201 %º PB
21
Q804,D801
Q806-808
BUFFER
IC201 %§ PB
IC201 $• REC
IC201 %º REC
REC CURR
PB RF
REC RF
REC
EQ
FM
MOD
0.5Vp-p
DE
EMPH.
RF SWP
IC260 @™ PB
CN261 2 PB
0.2V/Div
0.1µsec/div
IC260 #º REC
CN261 1 REC
200mV/Div
0.1µsec/div
200mV/Div
0.1µsec/div
0.5V/Div
0.1µsec/div
0.1V/Div
0.1µsec/div
RF ENV
IC161 60
C SYNC
IC161 66
S OUT1
IC161 80
S CLK1
IC161 81
RF SWP
IC161
1
FROM/TO
SYSCON
BLOCK
(SEE PAGE 3-6)
IC260 @• REC
CN261 3 PB
20mV/Div
0.1µsec/div
5Vp-p
30Hz
16
3-3
IC201 %§ REC
3.579545MHz
550mVp-p
14
1V/Div
0.1µsec/div
12
X201
3.579MHz
SEQ
SW1
IC260 4 REC
500mVp-p
H
(2/2)
66 C ROT
P
REC
4
5Vp-p
30Hz
13
9
IC161
45
0.1µsec/div
L262
SW8 SW4
HDET
S CLK 22
2.3Vp-p
IC260 !¶ REC/PB
6
6
CN162 7
4.8Vp-p
8MHz
16
PB
CN162 6
5
7
SP
CH2
CN162 8
SCK0
IC201 !∞ PB
L263
29
SW7 SW3
10
42
Y NR
NT 43
IC260 !• REC/PB
SO0
V SYNC 13
8 EXS
IC202
SI0
SI 16
Q209
R
P
PB
3 V IN
9 XS
X500
14.318MHz
CLP
Y/C
MIX
VIDEO
CN260
BUFFER
40
R
SUNC
SEP
37
CN162 21
TO
TUNER
BLOCK
YOUT 25
Q505
38
P CONT1
SO 17
SCK 15
RESET 19
OSD
C VCC 47
VIDEO
AGC
35
IC201 #¶ REC/PB
DRUM
VIDEO
HEAD
29 V SYNC
30
Y VCC 36
34
H
WAVE
SHAPER
IC500
L204
1Vp-p
H
LINE 1
IN
Q873,874
SW5V
IC201 @• REC
CJ570
VD 5
11 VCO O
5Vp-p
14.31818MHz
Y/C PROCESSOR
CN801
10 VCO I
28 H SYNC
X501
2Vp-p
H
HD 9
H
1Vp-p
H
JK-159
BOARD
CJ801
IC500 9 REC/PB
2 VIDEO
TU700 5
(SEE PAGE
3-11)
26 VIDEO
IC201 #∞ REC
2Vp-p
RF VIDEO
SYNC
DET/SET
3-4
64
I2C DATA VIDEO
IC161 28
63
I2C CLOCK VIDEO
IC161 30
(SEE PAGE
3-6)
SLV-798HF/998HF
3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM
MA-318 BOARD
(SEE PAGE 4-8, 11, 26)
IC161
(2/2)
SYSTEM CONTROL
M12V
DRUM MOTOR
CN101
M901
1
VCC
D161
IC100
OUTPUT
REF 2.5V
IC161
90 5V
(1/2)
SERVO CONTROL
6
SW12V
HALL
DEVICE
64 T REEL FG
A MUTE
IC201 70
AF ENV 59
AF ENV
IC360 39
AF SWP 100
AF SWP
IC340
1
AF REC P
IC340
4
AF REC
IC340
5
FE ON
Q832
FULL ERS
Q932
FULL ERS 36
3
3
D PG
63 S REEL FG
4
4
D FG
PH101
S REEL
FG
69 DRUM FG
5Vp-p
30Hz
IC260 26
IC201 37 ,IC260 18
DATA(SSB) 80
S OUT1
IC260 19
CLOCK(SSB) 81
S CLK1
IC260 20
RF SWP
IC260 17
Q VD
IC201 33
61 T SENS
UV+
7
7
VCC
1
1
TL
6
6
Q101
TAKE END
SENSOR
D6V
CN102
VM
5Vp-p
360Hz
LIMITER
D103
84 CAP TRQ PWM
T/S LED
99 STEP PLS
V-
62 S SENS
35 CAP STOP
W+
W-
IC100
D107
(2/2)
CAP ERR
INTEG
U
5
V
5
2
W
CAPSTAN
FG
2
3
3
CVS
Q102
SUPPLY END
SENSOR
IC161 &£ REC/PB
REF 2.5V
Q103
3
1
2
73 CAP DA
CAP RVS
LED
DRIVE
5Vp-p
360Hz
72 CAP RVS
CAP FG
IC201 64
IC201 63
C SYNC
Q VD 4
SW5V
PS101
U+
I2C DATA VIDEO
I2C CLOCK VIED
70 CAP FG
32 T/E LED
SI0
IC871 17
SO0
IC500 23 ,IC871 16
S CK 0
IC500 22 ,IC871 15
SYS RESET
IC871 19
VSET CS
IC871 32
H DET
IC501
CG CS
IC500 24
CG V
IC500 11
P CONT1
Q503
P CONT1
Q604
P CONT2
IC601
REC
PROOF
IC161 7 REC
15 REC PRF
REG OUT
1
6 STATUS
CONTROL
S OUT
9
42 XTAL
X160
16MHz
30Hz
7 REC CTL
CN301
CTL
HEAD
CNJ980
OUT
5 S OUT
CNJ981
CONTROL 11
S IN
IN
IC140
3
CTL
2 REC/PB
AMP
5
7
CN162
67 PB CTL
SIRCS OUT
3Vp-p
16MHz
5Vp-p
30Hz
SIRCS IN
Q140
GAIN
SW
P CONT2
P CONT1
IC101
92 CTL HYSHIGH
CG V
LOADING
MOTOR DRIVE
8 CTL RESET
CG CS
L101
M12V
H DET
8 VCC1
VSET CS
9 VCC2
LOADING
MOTOR
SYS RESET
ASURA RESET 40
CN103
2 CAM+
1
M
IN1 3
S CK 0
S CLK 47
2
SO0
S IN 0 45
10 CAM-
3
9 CAM2
IN2 4
SI0
S OUT 0 46
ASURA CS
ASURA CS 44
PLL ENABLE
CAM
ENCODER
4
MECHA
(POSITION
(
2
3
1
CABLE BOX
CONTROL/
CONTROL S
CTL AMP
1
6
TO
POWER
BLOCK
4 S IN
43 EXTAL
IC161 $£ REC/PB
IC161 ^¶ REC
4
REG
ON/OFF
12
CDC POWER 49
4Vp-p
8
SIRCS/CBC
I/O
NICOLON 48
5Vp-p
1.078kHz
(SEE PAGE
3-3, 4)
IC980
S101
IC161 &º REC/ PB
IC141
FROM/TO
VIDEO
BLOCK
REC CONT 77
CAPSTAN MOTOR
SW5V
FROM/TO
AUDIO
BLOCK
(SEE PAGE 3-8)
RF ENV
RF SWP 1
IC161 ^ª REC/PB
M12V
,IC360 40
V SYNC 66
RF ENV 60
68 DRUM PG
PG
FG
IC360 41
IC161 1 REC/PB
IC161 100
5Vp-p
360Hz
5Vp-p
30Hz
HALL
DEVICE
IC360 42
A MUTE 31
PH102
T REEL
FG
MATRIX
M902
I2C CLOCK1
FE ON 6
IC161 &¢ REC/PB
IC161 ^• REC/PB
I2C DATA1
SCL 0 30
AF REC 96
74 DRUM DA
OUTPUT
M
SDA 0 28
AF REC P 2
5
7
D VS
89 VDD
(1/2)
CAP ERR
INTEG
2
53 AVREF
54 AVDD
1
2
L161
D6V
D109
MODE1
MODE1
MODE2
MODE2
MODE3
MODE3
MODE4
MODE4
PLL CLOCK
22 MODE1
PLL DATA
21 MODE2
TU AFT
20 MODE3
MAIN/SAP
19 MODE4
SAP
STEREO
LANC IN
STEREO
IC733 11
SAP
IC733 10
MAIN/SAP
IC733
TU AFT
TU700 33
PLL DATA
TU700 21
PLL CLOCK
TU700 20
LANC OUT
8
PLL ENABLE
TU700 22
F MONO 50
F MONO
IC733
7
TA MUTE 11
TA MUTE
IC733
5
TV/VTR
TU700 4
16
3-5
3-6
22
21
23
12
2
18
20
6
TO/FROM
MODE
CONTROL
BLOCK
8
7
(SEE PAGE 3-9)
19
15
14
13
11
16
17
4
9
10
CN165
2
3
FROM/TO
TUNER
BLOCK
(SEE PAGE 3-12)
TV/VTR 26
5
3
D6V
4
FOR
CHECK
SLV-798HF/998HF
3-4. AUDIO BLOCK DIAGRAM
(SEE PAGE 4-5, 21)
MA-318 BOARD
FOR
CHECK
3
1
FM PB
HF ADJ
CN341
SW5V
IC340
CN260
3
AUDIO
PROCESSOR
(HIFI)
L341
AFM
REC/PB
AMP
DRUM
AUDIO
HEAD
IC360
SW12V
35
14
SW12V
15
VCC
HA
17
MUTE
EP
HF
LPF
CH1
PNR
L
VCO
18
2
3
VCC
REC ON
24
FM PB
37
OUTPUT
SEL
AGC
AMP
HA
20
1
MUTE
R
Q387
17
RF AUDIO
TU700 1
1
TU AUDIO L
IC733
3
2
TU AUDIO R
IC733
4
MUTE
13
FROM/TO
TUNER
BLOCK
CA
AGC
AMP
16
PB ON
9
H SW
1
FM REC
HF
LPF
36
Q386
MUTE
Q379
(SEE PAGE 3-11, 12)
MUTE
SW
NORMAL IN
40 AF SWP
21
AGC
DET
13
REC MUTE 4
LEVEL
DET
NORMAL OUT
REC 5
INPUT SEL
Q830,831
FULL
ERASE
HEAD
DRUM
AUDIO
HEAD
39
BIAS
ERASE
OSC
4
SEL
20
IC201
SDA
SCL
998HF MODEL
42 41
5
6
3
(2/2)
SW5V
AUDIO
PROCESSOR
(MONO)
4
76
REC
Q832
EQ
AVCC
10
7
11
PB:
LP,SP
PB
LINE
AMP
PB
MUTE
77
9
8
CJ570
LINE 1
IN
L
73
R
REC
71
80 A-H SW
LINE 2
IN
Q301
CN423
CN801
L
3
3
R
1
79
5
5
6
70
4
BIAS
SW
AUDIO
L2 R
3
REC:EP,LP
PB:EP
JK-159
BOARD
L2 L
REC
AUTO
BIAS
5
(SEE PAGE 4-33)
CJ801
MUTE
CTL
ALC
75
AUDIO
CN301
1
AUDIO
REC/PB
HEAD
IC301
2
NOMAL
AUDIO
2
HEAD
4
SW
FULL
4
HEAD
T331,Q331
FULL
ERASE
HEAD
BIAS
ERASE
OSC
1
CN302
IC161 31
I2C DATA1
IC161 28
I2C CLOCK1 IC161 30
SW12V
T931,Q931
FULL
ERASE
HEAD
A MUTE
SW5V
EXCEPT 998HF MODEL
1
CN931
BIAS
ERASE
OSC
Q932
998HF MODEL
AF ENV
IC161 59
AF SWP
IC161 100
FROM/TO
SYSCON
BLOCK
AF REC P
IC161
(SEE PAGE 3-6)
AF REC
IC161 96
2
FE ON
IC161
FULL ERS
IC161 36
16
3-7
CJ570
AUDIO
12
PNR
R
VCO
14
16
MUTE
SP
CH2
L
3-8
6
LINE
OUT
SLV-798HF/998HF
3-5. MODE CONTROL BLOCK DIAGRAM
FR-130 BOARD
(SEE PAGE 4-29)
IC460
TIMER/TUNER
MODE CONTROL
ND420
L182
D463
VACUUM FLUORESCENT
INDICATOR TUBE
24 AVDD
D6V
72 VDD
75 VPP
IC463
F+
5
D462
7
RESET
PULSE
GEN.
6
POWER
FAIL
DET.
8
27
29
10
11
9
20
30
14
12
FROM/TO
SYSCON
BLOCK
26
24
(SEE PAGE 3-6)
25
13
17
18
19
21
16
15
28
23
22
REMOTE
CONTROL
RECEIVER
G1
71
G6
66
SEG1
44
SEG16
59
1
FROM
POWER
BLOCK
-30V
2 POWER FAIL
IC461
2
F-
34 RST
EXTAL 43
X460
16MHz
CN460
SIRCS OUT
SIRCS IN
P CONT 2
6
SIRCS OUT
4
SIRCS IN
XTAL 42
79 P CONT 2
P CONT 1
78 P CONT 1
CG V
80 CG V
CG CS
TX 55
X461
32.768kHz
27 CG CS
H DET
VSET CS
3
H DET
TEX 54
40 VSET CS
SYS RESET
DM -74 BOARD
(SEE PAGE 4-32)
77 SYS RESET
S CK 0
10 S CK 0
SO0
12 S O 0
SI0
11 S I 0
ASURA CS
76 ASURA CS
PLL ENABLE
37 PLL ENABLE
PLL CLOCK
36 PLL CLOCK
PLL DATA
CN461
JOG LED 29
A/D 4 20
4
A/D 3 19
3
DMS 2 42
1
DMS 1 41
2
35 PLL DATA
TU AFT
S411
S412
REW
FF
Q440
CN440
5
JOG LED
PAUSE
A/D 4
DMS 2
DMS 1
D440
LED
DRIVE
5
JOG
4
3
1
S444
2
PAUSE
23 TU AFT
MAIN/SAP
988HF ONLY
38 MAIN/SAP
SAP
39 SAP DET
STEREO
5
LANC IN
A/D 2 18
STEREO DET
S441
S442
S443
EJECT
REC
JOG
14 LANC IN
LANC OUT
DMS BLOCK
QUICK SHUTTLE
CN441
1
15 LANC OUT
S406
S404
INPUT
SELECT
S403
EDIT
SP/EP
S407
S408
2
COMMAND
MODE
EASY
SETUP
3
4
5
IC462
EEPROM
SDA 5
SCL 6
MODE 7
28 EEP SDA
26 EEP SCL
13 WP
A/D 1 17
A/D 0 16
S405
S409
S410
CH
CH+
TV/VTR
BZ460
7 BUZZER
D460
Q460
LED
DRIVE
POWER ON
D5V
16
3-9
3-10
PLAY
STOP
PLAY
COM
DMS 2
DMS 1
STOP
SLV-798HF/998HF
3-6. TUNER BLOCK DIAGRAM
MA-318 BOARD
30V
(SEE PAGE 4-23)
SW5V
L704
L731
L703
IN
19
3
5V
5V
IF
RF
SPLITTER
VHF/
UHF
18
30V
TU700
TUNER/MOD/IF
TU VIDEO
36
IC733
TV
1 VCC
MPX
12 MPX IN
S701
AFT
DATA
CH 3
CLOCK
ENABLE
2
L 3
TU AUDIO L
IC360
1
R 4
TU AUDIO R
IC360
2
35
VTR
RF
MOD
33
RV731
SEPARATION
5
1
4
22
20
21
TO
AUDIO
BLOCK
(SEE PAGE 3-8)
ST IND 11
STEREO
CN162 4
SAP
CN162 17
MAIN/SAP
CN162 16
F MONO 7
F MONO
IC161 50
MUTE 5
TA MUTE
IC161 11
TU AFT
CN162 11
PLL DATA
CN162 13
PLL CLOCK
CN162 14
PLL ENABLE
CN162 15
TV/VTR
IC161 26
SAP IND 10
RF CH
TO
VIDEO
BLOCK
(SEE PAGE 3-3)
ST/BILINGUAL
PROCESSOR
OUT
CH 4
IC201 32
MS0 8
MS1 5
Q731
FROM
VIDEO
BLOCK
Q560
RF VIDEO
(SEE PAGE 3-4)
FROM
AUDIO
BLOCK
IC360 12
RF AUDIO
(SEE PAGE 3-8)
16
3-11
3-12
FROM/TO
SYSCON
BLOCK
(SEE PAGE
3-6)
SLV-798HF/998HF
3-7. POWER SUPPLY BLOCK DIAGRAM
(SEE PAGE 4-5, 8, 11, 15, 19, 21, 23, 25)
L604
1
5V
VCC
5V
5V
1
T931,Q932
2
SW12V
PS331
FE
BIAS
L731
12V
REG
3 19 32
R705
+30V
IC601
9. 13V
10
18
L704
CN603
30V
ST/BILNG
PROCESSOR
L703
EXCEPT
988HF Chilean, PX
MODEL
11
IC733
TU700
30V
MA-318 BOARD
IC201
OSC
POWER
BLOCK
4.
5
6V
P CONT 2
36 Y VCC
2
3
L206
-F(0V)
2.
3
13V
7.
8
6V
11
9
CHECK
PIN
AFC
L503
13 VCC
2 VDD
Q603,606
PS600
SW 5V
REG
CN162
D6V
D 6V
JS609
IC340
AFM
REC/PB AMP
IC360
IC201
AUDIO PROC.
(HIFI)
L341
+F
Q604,605
MOTOR
12V SW
988HF Chilean, PX
MODEL
T331,Q331
M12V
L331
P CONT 2
BIAS
ERASE
OSC
F+
L605
F-
L606
-30V
REC +B
SW
L607
D463
24 AVDD
35 AVREF
D462
72 VDD
75 VPP
76 AVCC
43 VFDP
P CONT 1
P CONT 2
IC301
21
11
22
10
78 POWER CONT 1
79 POWER CONT 2
IC461
HEAD SW
EEPROM
IC871
8 VCC
SYNC
DET/SET
Q830,831
BIAS
ERASE
OSC
IC161
20 VDD
SERVO/SYSTEM
CONTROL
D161
REMOTE
CONTROL
RECEIVER
IC462
1 VCC
998HF MODEL
Q833,834
L182
8.
7
AUDIO PROC.
(MONO)
35 12V
797HF/798HF MODEL
-F(10V)
CN460
24
.
25
(SEE PAGE 4-29)
TIMER/TUNER
MODE CONT.
(2/2)
L301
-30V
FR-130 BOARD
IC460
SW5V
14 VCC
10
4
IC501
1H DELAY
29 VCC
1
CN163
7 VCC
IC202
16 VCC
L263
CN602
30V
L502
D 6V
L202
-30V
4 AVCC
47 C VCC
VIDEO
REC/PB AMP
+F
OSD
L204
998HF MODEL
IC260
1
IC500
(1/2)
Y/C PROC.
4
IC100
D460
DRUM
CAPSTAN
AMP
POWER
ON
IC463
53 AVREF
54 AVDD
Q101,102
89 VDD
T/S
SENSOR
90 5V
ND420
RESET
5 VCC2 PULSE
GEN.
8 VCC
L160
2 VCC
FLUORESCENT
INDICATOR TUBE
POWER
7 VCC1 FAIL
DET.
F+
PH100,101
D420
T/S
REEL
IC980
-30V
+F
SIRCS/CBC
I/O
3
30
2
31
1
D5V
-F
29
14 REG IN
CN461
D982
13 VCC
6
IC140
IC101
CTL AMP
8 VCC
IC141
L101
8 VCC1
9 VCC2
DM-74 BOARD
L140
LOADING
MOTOR
DRIVE
CTL AMP
(SEE PAGE 4-32)
CN101
MTR 12V
1
DRUM
MOTOR
6
D109
L141
8 VCC
CN102
MTR 12V
SW 5V
7
1
CAPSTAN
MOTOR
PS101
16
3-13
CN440
3-14E
Q440
LED
DRIVE
D440
JOG
F-
SLV-798HF/998HF
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
(Chilean, PX)
(EXCEPT Chilean, PX)
(Chilean, PX)
(EXCEPT Chilean, PX)
4-1
4-2
FRAME SCHEMATIC DIAGRAM
SLV-798HF/998HF
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
MA-318 (REC/PB AMP, VIDEO, SERVO/SYSTEM CONTROL, AUDIO, TUNER) PRINTED WIRING BOARD
— Ref. No.: MA-318 Board; 1,000 Series —
REC/PB AMP, VIDEO, SERVO/SYSTEM CONTROL, AUDIO, TUNER
MA-318
4-3
There are few cases that the part printed on this diagram isn’t mounted in this model.
4-4
SLV-798HF/998HF
MA-318 (REC/PB AMP) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
MA-318 BOARD
MA-318 BOARD
CJ570
A-3
CN101
CN102
CN103
CN162
CN163
CN260
CN261
CN301
CN302
CN341
CN423
CN602
CN603
CN931
C-7
E-2
I-4
J-12
I-12
B-9
B-7
B-4
B-5
B-10
C-12
F-1
H-1
D-10
CNJ980
CNJ981
A-2
A-1
D103
D107
D109
D161
D370
D379
D502
D503
D504
D560
D561
D611
D612
D614
D702
D801
D802
D980
D981
D982
F-6
G-8
F-4
J-8
C-10
A-11
C-1
C-2
C-2
B-3
A-10
J-3
J-3
J-3
F-12
D-9
D-9
A-2
A-2
B-1
D983
D984
A-1
A-1
IC100
IC101
IC140
IC141
IC161
IC201
IC202
IC260
IC301
IC340
IC360
IC500
IC501
IC601
IC733
IC871
IC980
G-6
I-3
H-11
A-5
I-9
D-5
E-5
B-8
B-5
B-10
B-11
C-1
D-1
E-12
H-13
I-6
B-1
PH101
PH102
H-8
H-4
Q101
Q102
Q103
Q140
Q201
Q205
Q208
Q209
Q210
Q211
Q260
Q301
Q331
Q379
Q386
Q387
F-1
F-10
F-5
H-10
C-3
C-3
D-4
E-4
E-5
D-6
B-7
C-5
C-6
A-11
A-11
A-11
Q502
Q503
Q505
Q560
Q603
Q604
Q605
Q606
Q731
Q801
Q802
Q803
Q804
Q805
Q806
Q807
Q808
Q809
Q810
Q830
Q831
Q832
Q833
Q834
Q851
Q852
Q853
Q854
Q855
Q856
Q857
Q871
Q872
Q873
Q874
Q875
Q931
Q932
B-2
B-2
D-1
B-3
J-2
J-3
J-4
J-2
H-13
B-8
E-10
D-9
E-9
E-9
E-8
E-8
E-8
D-8
E-8
C-9
C-9
D-10
C-10
C-9
C-8
C-8
D-8
D-8
D-8
D-8
D-8
I-5
I-5
I-5
I-5
H-5
D-11
D-10
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
1 IC260 4 REC
• For printed wiring boards.
• b : Pattern from the side which enables seeing.
1V/Div
0.1µsec/div
Caution :
Pattern face side:
(Conductor Side)
Parts on the pattern face side
seen from the pattern face are
indicated.
Pattern face side: parts on the parts face side seen
(Component Side) from the parts face are indicated.
2 IC260 #º REC
CN261 1 REC
0.5V/Div
0.1µsec/div
• For schematic diagrams.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, because it is damaged by the heat.
• All resistor are in ohms, 1/4W unless otherwise noted.
Chip resistor are 1/10W unless otherwise noted.
kΩ: 1000Ω, MΩ, : 1000kΩ.
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50V or less are not indicated except for electrolytics
and tantalums.
• C: panel designation.
: internal component.
•
• A: B+ Line. *
• B: B– Line. *
• J : IN/OUT direction of (+,–) B LINE. *
• Circled numbers refer to waveforms. *
• Readings are taken with a color-bar signal input.
• Voltage are dc between ground and measurement
points.*
• Readings are taken with a digital multimeter (DC10MΩ).*
• Voltage variations may be noted due to normal production
tolerances.*
3 IC260 @• REC
20mV/Div
0.1µsec/div
4 IC260 @™ PB
200mV/Div
0.1µsec/div
5 IC260 !• REC/PB
H
2.3Vp-p
6 IC260 !¶ REC/PB
When indicating parts by reference number, please
include the board name.
CN261 3 REC/PB
• * : indicated by the color red.
5Vp-p
30Hz
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
4-5
4-6
4-7
REC/PB AMP
MA-318 (1/10)
SLV-798HF/998HF
MA-318 (VIDEO, NORMAL AUDIO) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
• See page 4-3 for MA-318 BOARD printed wiring board.
MA-318 BOARD
7 IC201 !∞ PB
!£ IC201 #• REC/ PB
CN261 2 PB
2Vp-p
H
200mV/Div
0.1µsec/div
8 IC201 @º PB
!¢ IC201 $∞ PB
9 IC201 @∞ REC
H
500mVp-p
H
0.1V/div
0.1µsec/div
!∞ IC201 %§ REC
0.5Vp-p
!º IC201 @• REC
3.579545MHz
550mVp-p
!∞ IC201 %§ PB
1Vp-p
H
3.579545MHz
500mVp-p
!¡ IC201 #∞ REC
!§ IC201 $• REC
IC201 %º REC
1Vp-p
H
H
!™ IC201 #¶ REC/PB
340mVp-p
!§ IC201 $• PB
IC201 %º PB
H
4Vp-p
H
VIDEO, NORMAL AUDIO
MA-318 (2/10)
0.23Vp-p
4-8
4-9
4-10
SLV-798HF/998HF
MA-318 (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
• See page 4-3 for MA-318 BOARD printed wiring board.
MA-318 BOARD
!¶ IC161 1 REC/PB
!• IC161 100
5Vp-p
30Hz
!ª IC161 $£ REC/PB
3Vp-p
16MHz
@º IC161 &º REC/ PB
5Vp-p
1.078kHz
@¡ IC161 &£ REC/PB
5Vp-p
360Hz
@£ IC161 ^• REC/PB
5Vp-p
30Hz
@¢ IC161 ^ª REC/PB
5Vp-p
360Hz
@∞ IC161 7 REC
4Vp-p
30Hz
@§ IC161 ^¶ REC
5Vp-p
30Hz
@™ IC161 &¢ REC/PB
5Vp-p
360Hz
4-11
4-12
4-13
SERVO/SYSTEM CONTROL
MA-318 (3/10)
SLV-798HF/998HF
SLV-798HF/998HF
• See page 4-3 for MA-318 BOARD printed wiring board.
MA-318 (ON SCREEN DISPLAY) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
MA-318 BOARD
@¶ IC501 !º REC/PB
@• IC500 9 REC/PB
@ª IC500 3, @∞ REC/PB
2Vp-p
5Vp-p
14.31818MHz
503.5kHz
0.65Vp-p
ON SCREEN DISPLAY
MA-318 (4/10)
4-15
4-16
H
SLV-798HF/998HF
MA-318 (DSF) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
• See page 4-3 for MA-318 BOARD printed wiring board.
MA-318
BOARD
#º Q802 B PB
0.2V/div
0.1µsec/div
4-17
4-18
#¡ Q810 E PB
0.1V/div
0.1µsec/div
DSF
MA-318 (5/10)
SLV-798HF/998HF
MA-318 (V-SET) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
• See page 4-3 for MA-318 BOARD printed wiring board.
MA-318
BOARD
#™ IC871 #º REC/PB
4.8Vp-p
8MHz
V-SET
MA-318 (6/10)
4-19
4-20
SLV-798HF/998HF
MA-318 (AFM AUDIO) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
• See page 4-3 for MA-318 BOARD printed wiring board.
4-21
4-22
AFM AUDIO
MA-318 (7/10)
SLV-798HF/998HF
MA-318 (TUNER) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
TUNER
MA-318 (8/10)
• See page 4-3 for MA-318 BOARD printed wiring board.
4-23
4-24
SLV-798HF/998HF
MA-318 (POWER SUPPLY, AV-BUS) SCHEMATIC DIAGRAM
— Ref. No.: MA-318 Board; 1,000 Series —
4-25
• See page 4-3 for MA-318 BOARD printed wiring board.
4-26
POWER SUPPLY, AV-BUS
MA-318 (9/10) (10/10)
SLV-798HF/998HF
FR-130 (MODE CONTROL) PRINTED WIRING BOARD
— Ref. No.: FR-130 Board; 2,000 Series —
FR-130 BOARD
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
MODE CONTROL
FR-130
There are few cases that the part printed on this diagram isn’t mounted in this model.
CN460
CN461
A-11
D-1
D420
D460
D462
D463
B-10
A-13
B-10
B-10
IC460
IC461
IC462
IC463
B-11
B-13
C-13
D-13
Q460
B-13
4-27
FR-130 BOARD
1 IC460 #™ REC/PB
4Vp-p
16MHz
2 IC460 $¡ REC/PB
2Vp-p
32.768kHz
4-28
SLV-798HF/998HF
FR-130 (MODE CONTROL) SCHEMATIC DIAGRAM
— Ref. No.: FR-130 Board; 2,000 Series —
4-29
4-30
MODE CONTROL
FR-130
SLV-798HF/998HF
DM-74 (OPERATION SWITCHES) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
— Ref. No.: DM-74 Board; 2,000 Series —
There are few cases that the part printed on this diagram isn’t mounted in this model.
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
OPERATION SWITCHES
DM-74
4-31
4-32
SLV-798HF/998HF
There are few cases that the part printed on this diagram isn’t mounted in this model.
JK-159 (LINE-2 IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
— Ref. No.: JK-159 Board; 2,000 Series —
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
4-33
LINE-2 IN
JK-159
SLV-798HF/998HF
SLV-798HF/998HF
POWER BLOCK SR801 (SWITCHING REGULATOR) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
— Ref. No.: SR801 Board; 8,000 Series —
2
3
4
5
6
POWER BLOCK (SR801)
A
T101 POWER TRANSFORMER
(EXCEPT Chilean, PX MODEL)
P1
B
L101
C102
0.1/250
L
C101
0.1/250
AC IN
120VAC
D107-110
1N4005
H
D110
D102
EG01
R103
100K
D107
R101
6.8M
1/2
C
C105
1500P
125
D205
RD51F
C205
470/10
S1
*R207
C110
0.047
D
B1
+
11 +38
10 +13
9 +13
8 GND
7 GND
6 GND
5 +6V
4 +6V
SHUNT REG.
AN1431T
Q102
2SC4040
D103
ERA15-02
+
CN201
IC201
Q101
2SC4054
C112
0.0047
C203
220/16
D204
D3S4M
C204
1000/10 +
R104
10K
C104
470P
125
+
L203
20uH
C107
4.7/50
C103
0.1/125
12
L202
20uH
S3
Q101,102
SWITCHING
CN101
11
R201
10 1/2
C202
1000/16
P2
10
C201
47/50
FB1
+ C106
120/200
D108
D201
PR1003
D202
S3L20U
R102
100K
D109
S5
9
S4
R106
33K/3
C109
0.033
400
D106
1N4005
F101
2A 125V
8
7
C208
1/50
PC101
ON3131
C206
47/50
+
3 -30V
2 -F(0V)
1 +F(4.5V)
R206
1.8K
+
1
There are few cases that the part printed on this diagram isn’t mounted in this model.
*R107
GND
D108
MA165
C111
0.047
R108
22
C209
0.01
VR201
500
R205
47
1/2
PC101
ON3131
*R109
E
D104
RD3.0ES
S6
B2
R208
10
1/2
D206
PR1003
S8
+
Ref. No
R107
F
min
typ
max
R109
100/1
560
120/1
620
120/1
680
R207
1.2k
1.5k
2.2k
D207
PR1003
S7
16
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
C207
470/10
R204
0.47
R209
2.7
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
SWITCHING REGULATOR
POWER BLOCK SR801
4-35
4-36
TO
MA-318 BOARD
CN603
(SEE PAGE 4-25)
SLV-798HF/998HF
POWER BLOCK SR709 (SWITCHING REGULATOR) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
— Ref. No.: SR709 Board; 9,000 Series —
2
3
4
5
6
8
7
POWER BLOCK (SR709)
A
T101 POWER TRANSFORMER
(Chilean, PX MODEL)
P1
B
C102
L101
0.1/250
L102
D102
L
C101
0.1/250
AC IN
110-240VAC
D101 - 104
1N4005
1
R101
1M
1/2W
D204
RD56FB
L202
10uH
C203
220/16
H
D103
D104
C116
47p
1k
+
C
C109
180
400
R108
47
1
+
C112
0.1
C107
1000p
250
C108
1000p
250
GND
min
typ
max
R104
0
10k
6.8
10k
100
15k
R106
100k
120k
220k
R202
47
470
470
R205
1k
10k
47k
R207
0
2.7
4.7
R208
10
47
R209
10
V1
CN201
+
C205
470/10
C204
1000/16
*R204
D108
D107 V2
PR1003 PR1003
PC101
PC123
C206
47/50
+
1
2
3
4
5
6
7
8
+
*R205
VR201
5k
R203
18k
+38
+13
+13
GND
GND
GND
+6V
+6V
TO
MA-318 BOARD
CN602
(SEE PAGE 4-25)
9 -27V
10 -F(0V)
11 +F(4.6V)
C208
0.1
R107
6.8
C209
0.047
*R202
D205
PR1003
*R106
R105
3.3k
IC201
C210
1000p
1k
SHUNT REG.
AN1431T
PC101
PC123
*R104
D
D203
D3S6M
C111
47
35
*R103
C104
1000p
250
+
L203
10uH
P2
C103
1000p
250
E
+
C202
1000/16
D105
EG01C
D101
13
12
R201
4.7 1/2
C201
47/63
5
CN101
Ref. No
R103
D201
EG01C
D202
S3L20U
MIP184
2 3 4
11
10
C110
0.01
400
R102
47k
3
IC101
F101
T2AL 250V
9
C113
0.01
*R208
C114
0.1
C115
0.1
+
1
There are few cases that the part printed on this diagram isn’t mounted in this model.
C207
470/10
D206
PR1003
F
R206
0.47
16
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
R207
2.7
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-318
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
JK-159
(LINE-2 IN)
FR-130
(MODE CONTROL)
POWER BLOCK
DM-74
(OPERATION SWITCHES)
4-37
4-38E
SWITCHING REGULATOR
POWER BLOCK SR709
O
I
O
4
^§
!£
QVD
V SYNC
NT JUDGE
STOP
L
*4
L
*1
FF/REW
TAPE
TAPE
L
*5
L
*1
L
*5
*2
*1
PB
L
*5
*3
*1
PB PAUSE
L
*5
*3
*1
SLOW
L
*5
*2
*1
x2
L
*5
*3
*1
CUE
L
*5
*3
*1
REVIEW
L
*5
L
*1
REC
I/O
O
O (O.D)
O
I
I
I
I
Pin No.
7
#∞
(ª
^¶
^•
^ª
&º
REC CTL
CAP STOP
STEP PLS
PB CTL
DRM PG
DRM FG
CAP FG
5-1
O
I/O
&¢
8
DRM DA
CTL RESET
Hi-Z
*10
*8
H/L
*4
*4
H
L
L
Hi-Z
STOP
*1. 30Hz pulse.
*2. Pulse at tape running.
*3. Reverse logic pulse of STEP PLS.
*4. “L” when drum rotation stops.
*5. Unstable period pulse.
*6. Pulse in period in proportional to tape speed.
*7. 360Hz pulse.
*8. Pulse at tape running.
*9. Approx. 2 msec period “H” or “L” pulse.
*10. Approx. 1.5 msec period “H” or “L” pulse.
*11. “L” when FWD SLOW, “H” when RVS SLOW.
O
&£
CAP DA
Signal
Hi-Z
*10
*8
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
FF
Hi-Z
*10
*8
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
REW
TAPE
TAPE
Hi-Z
*10
*8
*5
*5
*5
L
Hi-Z (O.D)
Hi-Z
Hi-Z
*10
*8
*5
*5
*5
L
Hi-Z (O.D)
Hi-Z
THREADING UNTHREADING
PB
Hi-Z
*10
*9
*6
*7
*1
*1
L
Hi-Z (O.D)
Hi-Z
Hi-Z
*10
*8
H/L
*7
*1
H/L
L
L
Hi-Z
PB PAUSE
*11
*10
*8
*2
*7
*1
*2
*2
*3
Hi-Z
SLOW
Hi-Z
*10
*9
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
CUE
x2
Hi-Z
*10
*8
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
Hi-Z
*10
*9
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
REVIEW
L
*5
L
*1
REC PAUSE
5-2. SYSTEM CONTROL — SERVO PERIPHERAL CIRCUIT INTERFACE (MA-318 BOARD IC161)
L
*5
L
*1
THREADING UNTHREADING
Synchronized with drum rotation. 30Hz 50% duty cycle.
Normally “L“. “H“ when CTL signal is not generated.
V period “H“ pulse.
Selected by REC mode. “H“ in LP mode.“
Composite sync signal (positive).
O
1
RF SWP
*1
*2
*3
*4
*5
I/O
Pin No.
Signal
5-1. SYSTEM CONTROL — VIDEO BLOCK INTERFACE (MA-318 BOARD IC161)
Hi-Z
*10
*9
*6
*7
*1
*1
L
Hi-Z (O.D)
*1
REC
Hi-Z
*10
*8
H/L
*7
*1
H
L
Hi-Z (O.D)
Hi-Z
REC PAUSE
SECTION 5
INTERFACE, IC PIN FUNCTION DESCRIPTION
SLV-798HF/998HF
5-2
I
I
I
I
I
I
I
O (O.D)
O (O.D)
O
I
I
@™
@¡
@º
!ª
!∞
^¢
^£
#™
#∞
&™
^¡
^™
MODE 1 (*8)
MODE 2 (*8)
MODE 3 (*8)
MODE 4 (*8)
(IN REC PRF)
T REEL FG
S REEL FG
T/E LED
CAP STOP
CAP RVS
T SENS
S SENS
*4
*4
H
L
*4
H/L
H/L
H
L
L
H
H
L
EJECTED
*4
*4
L
*4
H/L
H/L
*2
H
L
L
L
H
LOADING
TAPE
TAPE
*4
*4
L
*4
H/L
H/L
*2
H
L
L
L
L
L
*6
*6
H
H
*4
*3
H/L
*2
*1
*1
*1
*1
*6
*6
H/L
L
*4
H/L
H/L
*2
L
H
H
H
*7
STOP
*6
*6
L
H
*4
*3
*3
*2
H
L
H
H
*7
FF
*6
*6
H
H
*4
*3
*3
*2
H
L
H
H
*7
REW
*6
*6
L
H
*4
*3
*3
*2
H
L
L
H
*7
PB
*6
*6
L
L
*4
H/L
H/L
*2
L
L
L
H
*7
PB PAUSE
*6
*6
L/*5
*5
*4
*3
*3
*2
L
L
L
H
*7
SLOW
*6
*6
L
H
*4
*3
*3
*2
L
L
L
H
*7
x2
*6
*6
L
H
*4
*3
*3
*2
L
L
L
H
*7
CUE
*6
*6
H
H
*4
*3
*3
*2
L
H
L
L
*7
REVIEW
I
I
I
O
I
$º
$¢
$∞
$§
$¶
ASURA CS
S IN 0
S OUT 0
S CLK
I/O Level
Serial communication clock from timer microprocessor. V period “L” pulse.
Serial communication data to timer microprocessor. V period “L” pulse.
Serial communication data from timer microprocessor. V period “ L” pulse.
Chip select signal from timer microprocessor. V period “L” pulse.
Normally “H”, “L” when service interruption is detected or restored.
I
O (O.D)
O
O
O (O.D)
%ª
#¡
2
`⁄‚‚
#§
AF ENV
A MUTE
AF REC P
AF SWP
FULL ERS
TAPE
LOADING
TAPE
UNLOADING
PB
H
*1
L
L
H
*1
L
L
H
*1
L
L
H
*1
L
*1
H
*1
L
H
PB PAUSE
AF RF envelope signal input terminal for automatic tracking.
REW
STOP/FF/
*1. 30 Hz 50 % duty pulse approx. 5 msec delayed from RF SW P.
I/O
Pin No.
Signal
H
*1
L
H
SLOW
H
*1
L
H
x2
H
*1
L
H
CUE
5-5. SYSTEM CONTROL — AUDIO BLOCK INTERFACE (MA-318 BOARD IC161)
I/O
Pin No.
Signal
ASURA RESET
H
*1
L
H
REVIEW
L
*1
H
L
REC
H
*1
L
L
REC PAUSE
5-4. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE (MA-318 BOARD IC161)
*7. When transition to UNLOADING direction : “L”.
When transition to LOADING direction : “H”.
When CAM MOTOR is stopped : Hi-Z.
*8. When RVS slow : Mode 1=”L”
When RVS slow : Mode 2=”L”
When RVS slow : Mode 3=”H”
When RVS slow : Mode 4=”L”
*6
*6
L
H
*4
*3
H/L
*2
*1
*1
*1
*1
H
UNLOADING THREADING UNTHREADING
CASSETTE CASSETTE
Uncertainly.
“L” when erasing protection tab is bent. “H” when not bent.
Pause of period in proportion to reel rotating speed.
Approx. 2 msec period “H” pulse.
Pulse at tape running.
Normally “L”. 2 msec period “H” pulse when tape top or tape end is detected.
HI-Z
9
CAM2
*1.
*2.
*3.
*4.
*5.
*6.
I/O
Pin No.
Signal
5-3. SYSTEM CONTROL — MECHANISM INTERFACE (MA-318 BOARD IC161)
*6
*6
L
H
*4
*3
*3
*2
L
L
L
H
*7
REC
REC
*6
*6
L
L
*4
H/L
H/L
*2
L
L
L
H
*7
PAUSE
5-6. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS
(MA-318 BOARD IC161)
8
CTL RESET
O
9
10
11
12
13
14
CAM 2
N.C.
TA MUTE
S-VHS
NT JUDGE
MESECAM DET
I
—
O
I
I
I
15
CIN (REC PRF)
I
16
17
18
19
20
21
22
O
—
—
I
I
I
I
O
Not used.
O
Not used.
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
AV CONT
SECAM ON
SW1
MODE 4
MODE 3
MODE 2
MODE 1
POWER SAVE
CONT 1
POWER SAVE
C+
MOD CONT
TV/VTR
N.C.
SDA 0
N.C.
SCL 0
A MUTE
T/E LED
N.C.
N.C.
CAP STOP
FULL ERS
N.C.
N.C.
MP
ASURA RESET
VSS
XTAL
EXTAL
Function
RF switching pulse output.
“H” when HiFi audio REC.
Not used.
Quasi VD pulse output.
“H” during auto preset.
Flying erase ON/OFF
REC CTL signal output.
Capstan current control. “H” during
slow mode.
Cam motor control.
Not used.
Tuner audio mute. H: Mute
Not used.
Not used.
Not used.
Erasing protection tab, cassette in
detection signal input.
Not used.
Not used.
Not used.
Cam encoder signal input.
Cam encoder signal input.
Cam encoder signal input.
Cam encoder signal input.
44
ASURA CS
I
45
46
47
48
49
50
S IN 0
S OUT 0
SCLK
NICOL ON
CBC POWER
F. MONO
I
O
I
O
O
O
Pin No.
1
2
3
4
5
6
7
23
24
Pin Name
RF SWP
AF REC P
N.C.
QVD
AUTO PRESET
FE ON
REC CTL
I/O
O
O
—
O
O
O
O
O
O
—
I/O
—
I/O
O
O
—
—
O
O
—
—
I
I
—
O
I
Pin No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
Not used.
TV/VTR control signal output.
Not used.
I2C data.
Not used.
I2C clock.
“H” when audio mute.
Tape top/end sensors driver.
Not used.
Not used.
Capstan stop signal output.
Full erase control.
Not used.
Not used.
Fixed to “L”.
System reset signal.
Ground.
System clock 16MHz.
System clock 16MHz.
Servo/system control microcomputer
chip select signal.
Serial communication signal.
Serial communication signal.
Serial communication signal.
NICOL control signal out.
Cable box control signal out.
Forced mono.
5-3
Pin Name
SW2
AVSS
AVREF
AVDD
NTPB SW
AV ADJ
FOLLOW TV
N.C.
AF ENV
RF ENV
T SENS
S SENS
S REEL FG
T REEL FG
N.C.
VSYNC
PB CTL
DRM PG
DRM FG
CAP FG
BLUE BACK
ON
I/O
O
—
—
—
I
I
I
—
I
I
I
I
I
I
—
I
I
I
I
I
O
72
CAP RVS
O
73
74
75
76
77
78
79
80
81
82
83
CAP DA
DRM DA
N.C.
N.C.
REC COUNT
C PLUS DET
N.C.
DATA (SSB)
CLOCK (SSB)
N.C.
N.C.
O
O
—
—
I
O
—
O
O
—
—
84
CAP TRQ PWM
O
85
86
87
88
89
90
91
92
93
94
95
96
97
98
N.C.
N.C.
N.C.
VSS
VDD
5V
N.C.
CTL HYS HIGH
N.C.
N.C.
N.C.
AF REC
N.C.
N.C.
—
—
—
—
—
—
—
O
—
—
—
O
—
—
99
STEP PLS
O
100
AF SWP
O
Function
Not used.
Unswitched ground.
AD port reference input UNSW 5V.
UNSW 5V.
Not used.
Adjustment mode.
Not used.
Not used.
HiFi audio playback signal envelope.
Video playback signal envelope.
Take-up end sensor.
Supply end sensor.
Supply reel FG input.
Take-up reel FG input.
Not used.
Composite sync. signal input.
Playback CTL input.
Drum PG input.
Drum FG input.
Capstan FG input.
Not used.
Capstan reverse control “H” when
reverse.
Capstan error D/A output.
Drum PG output.
Not used.
Not used.
Counter signal input when recording.
Not used.
Not used.
Serial communication data.
Serial communication clock.
Not used.
Not used.
PWM output for capstan torque
control.
Not used.
Not used.
Not used.
Ground.
5V.
5V.
Not used.
CTL amp gain control.
Not used.
Not used.
Not used.
“H” output when hifi audio recording.
Not used.
Not used.
Step pulse “H” when capstan step
driving.
AF switching pulse output.
5-7. TUNER/TIMER MODE CONTROL PIN FUNCTIONS (FR-130 BOARD IC460)
Pin No.
Pin Name
1
N.C.
2
POWER FAIL
Pin No.
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
I/O
Function
I Not used.
I Power failure detect signal input.
H DET_(TUNER H SYNC detect
I
input).
Remote control signal (SIRCS)
I
input.
I Stereo judge input.
Remote control signal (SIRCS)
O
output.
O Buzzer signal output.
O Not used.
O Not used.
Serial communication signal (Serial
I
clock).
Serial communication signal (Data
I
input).
Serial communication signal (Data
O
output).
3
H DET
4
SIRCS IN
5
STEREO DET
6
SW1 SIRCS OUT
7
8
9
BUZZER
N.C.
N.C.
10
SCK 0
11
SI 0
12
SO 0
13
14
15
16
17
18
19
20
21
22
23
24
25
26
WP
LANC IN
LANC OUT
A/D 0
A/D 1
A/D 2
A/D 3
A/D 4
N.C.
N.C.
AFT
AVDD
AV REF
SCL 0
O
I
O
I
I
I
I
I
I
I
I
27
CG CS
O
28
29
30
31
32
33
34
35
36
37
SDA 0
JOG LED
AVSS
EXTAL
XTAL
VSS
RST
PLL CLK
PLL DATA
PLL ENABLE
O
O
I
38
MAIN/SAP
O
39
40
41
42
43
44
45
46
47
48
49
SAP DET
V SET CS
DMS 1
DMS 2
VFDP
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
O
O
I
I
I
O
O
O
O
O
O
O
I
O
O
O
EEP mode control.
LANC input.
LANC output.
Analog voltage (KEY) input.
Analog voltage (KEY) input.
Analog voltage (KEY) Input.
Analog voltage (KEY) Input.
Analog voltage (KEY) Input.
Not used.
Not used.
AFT (Auto fine tuning signal input).
A/D port reference input.
UNSW 5V.
T BUS (clock) /IIC BUS (clock).
Character generator chip select
signal.
IIC BUS (data).
JOG LED control signal output.
UNSW GND
System clock terminal (16MHz).
System clock terminal (16MHz).
GND
RESET input.
TUNER PLL clock.
TUNER PLL data.
TUNER chip select.
NO USE (MAIN/SAP judge signal
output).
MAIN/SAP judge input.
V SET IC chip select signal.
DMS forward/reverse signal input.
DMS forward/reverse signal input.
VFDP.
Segment terminal 1
Segment terminal 2
Segment terminal 3
Segment terminal 4
Segment terminal 5
Segment terminal 6
5-4E
Pin Name
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
NC
NC
NC
NC
NC
NC
GRID6
GRID5
I/O
O
O
O
O
O
O
O
O
O
O
68
69
70
71
72
73
74
75
GRID4
GRID3
GRID2
GRID1
VDD
TX
TEX
NC/VPP
O
O
O
O
76
ASURA CS
O
77
78
79
80
SYS RESET
POWER CONT 1
POWER CONT 2
CG V
O
O
O
I
O
O
O
Function
Segment terminal 7
Segment terminal 8.
Segment terminal 9.
Segment terminal 10.
Segment terminal 11.
Segment terminal 12.
Segment terminal 13.
Segment terminal 14.
Segment terminal 15.
Segment terminal 16.
Non Connect.
Non Connect.
Non Connect.
Non Connect.
Non Connect.
Non Connect.
Grid terminal 6.
Grid terminal 5.
Grid terminal 4.
Grid terminal 3.
Grid terminal 2.
Grid terminal 1.
D5V
Timer clock terminal (32.768kHz).
Timer clock terminal (32.768kHz).
D5V
S/S microcomputer chip select
signal.
System reset output.
Power supply control signal.
Power supply control signal.
Composite sync input.
SLV-798HF/998HF
SECTION 6
ADJUSTMENTS
2-1-3. Input Signal Check
Video signal produced by a pattern generator is used as an adjustment
signal to perform electrical alignment for this unit. This video signal
must satisfy the specification.
6-1 MECHANICAL ADJUSTMENTS
For the mechanical adjustments, please refer to the
“VHS MECHANICAL ADJUSTMENT MANUAL
(S MECHANISM)” (9-921-647-11).
Unless otherwise specified, place the switches and controls of this
unit in the following positions:
• INPUT SELECT switch ............................. LINE or LINE 1
(Remote commander)
6-2. ELECTRICAL ADJUSTMENTS
See the adjusting parts location diagram from on page 6-8
for the adjustment.
Connect an oscilloscope to the Video Input terminal. Check that the
synchronizing signal of the Y signal has an amplitude of
approximately 0.7V and that the burst signal has an amplitude of
approximately 0.3V and its waveform is flat. And check that the
level ratio of burst signal to “red” signal is 0.30 : 0.66. The video
signal (color bar) used for electrical aligning this unit is shown in
Fig. 6-2-2.
2-1. PREPARATION BEFORE ADJUSTMENT
2-1-1. Equipment Required
The measuring instruments used for this alignment include:
1) Monitor TV
2) Oscilloscope, dual-trace, bandwidth of 30MHz or more, with
delay mode (A probe 10:1 should be used unless otherwise
specified.)
3) Frequency counter
4) Pattern generator
5) Digital voltmeter
6) Audio generator
7) Audio level meter
8) Audio distortion meter
9) Audio attenuator
10) Alignment tapes
KRV-51N2
Part No.: 8-192-605-32
White (100%)
About 0.7 V
About
0.3 V
About
0.3 V
Red
Horizontal sync signal
2-1-2. Equipment Connection
Unless otherwise specified, connect and adjust the measuring
instruments as shown in the following diagram.
Fig. 6-2-2. Color Bar Signals of Pattern Generator
2-1-4. Alignment Tape
• Contents of KRV-51N2
VIDEO LINE IN
Pattern generator
Video output
(75Ω)
Burst signal
(It must be flat.)
VCR
Mode
Monitor TV
1
2
3
4
VIDEO LINE OUT
Fig. 6-2-1.
6-1
SP
EP
Period
Video signal
Audio signal
Normal
Hi-Fi
7 minutes
3 minutes
7 minutes
3 minutes
Color bar
Monoscope
Color bar
Monoscope
400Hz
400Hz
2-1-5. Input/Output Levels and Impedance
Video input: LINE IN
Input signal: 1Vp-p, 75ohms, unbalanced,
sync negative
Video output: LINE OUT
Output signal: 1Vp-p, 75ohms, unbalanced,
sync negative
Audio input: LINE IN
Input level: –7.5 dBs
(0dBs= 0.775Vrms)
Input impedance: more than 47 kilohms
Audio output: LINE OUT
Standard level: –7.5dBs at load impedance 47
kilohms
Output impedance: less than 10 kilohms
2-2. POWER SUPPLY CHECK
2-2-1. Output Voltage Check (MA-318 Board)
Mode
E-E
2-1-6. Adjustment Sequence
The adjustments should be performed in the following sequence.
Measuring Instrument
SW 12V Check
Digital voltmeter
Measurement point
Specified value
IC601 pin 2
12.0 ± 0.3V
MTR12V Check
Measurement point
Q605 C
Specified value
SW5V Check
13.2 ± 1.0V
Measurement point
Specified value
Q603 E
5.1 ± 0.3V
[Check Method]
1) Each of these supply voltages must meet its specified value.
Power Supply Check
Servo System Adjustments
Audio System Adjustments
Video System Adjustments
Tuner System Adjustments
6-2
2-3. SERVO SYSTEM CHECK
Unless otherwise specified, set the switches to the following
positions.
•
INPUT SELECT
switch ............................. LINE or LINE 1
(Remote commander)
switch ...................... SP (Remote commander)
•
TAPE SPEED
2-3-1. RF Switching Position/
AF Switching Position Adjustments
(MA-318 Board)
[Adjustment Purpose]
To adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.
Mode
Playback
Signal
Measurement point
Alignment tape: SP color bar portion
CH1: Video LINE OUT
(RF switching position)
CN341 pin 1 (HF ADJ)
(AF switching position)
CH2: CN261 pin 3 (RF SWP)
Measuring instrument
Specified value
Oscilloscope
6.5 ± 0.5H (410 ± 32 µsec)
[Adjustment Method]
1) Short-circuit between JS161 and ground for about 1 second to
activate the RF switching position adjustment mode.
2) Check that “AP” is indicated on FL display.
3) Using the channel + and – buttons, adjust to 410 ± 32 µsec (6.5
± 0.5H).
4) Press the PAUSE button. (Adjustment is over for mono models.)
5) The set goes to the AF switching position adjustment mode.
CH1
Approx.
1Vp-p
CH2
Approx.
5Vp-p
6)
7)
Check that “AH” is indicated on FL display.
Using the channel + and – buttons, minimize a chipped portion.
At this time, confirm that a noisy sound is not heard.
8) Press the PAUSE button.
9) Check that “AH” indication is disappeared. When it is not
disappeared, repeat from the item 1).
10) Press the STOP button.
11) Press the EJECT button.
CH2
RF SWP
CN261 pin 3
V
OK
CH1
REC AFM
CN341
pin 1
Enlarrgement
Vertical sync. signal
NG
CH1
CH2
CN261 pin 3
Should be minimized
6.5 ± 0.5H
RF signal dropout
Fig. 6-2-3.
Fig. 6-2-4.
6-3
2-4. VIDEO SYSTEM CHECKS AND ADJUSTMENT
For the video system checks, follow the checking procedures given
below as a rule. The color bar video signal supplied from the pattern
generator is used as the video input signal for the video system
adjustment of the recording mode. Check that the signal satisfies
the specified value designated in the “Check of input signal” (Fig.
6-2-2)
Unless otherwise specified, set the switches to the following
positions.
•
INPUT SELECT
•
TAPE SPEED
2-4-2. SYNC AGC Check (MA-318 Board)
Mode
E-E
Signal
Measurement point
Color bar
IC201 pin #•
Measuring instrument
Specified value
Oscilloscope
A=2.10 ± 0.10Vp-p
[Check Method]
1) Check that the Video signal level (A) satisfies the specified
value.
switch ............................. LINE or LINE 1
(Remote commander)
switch ...................... SP (Remote commander)
White (100%)
[Checking Sequence]
1) X’tal OSC Check
2) SYNC AGC Check
3) Recording Y Level Check
4) Recording Chroma Level Check
5) Playback Level Check
A
2-4-1. X’tal OSC Check (MA-318 Board)
Mode
Playback
Signal
Measurement point
Alignment tape: SP Color bar portion
IC201 pin %§
Measuring instrument
Specified value
Oscilloscope and Frequency counter
3,579,545 ± 70Hz
H
Fig. 6-2-6.
2-4-3. Recording Y Level Check (MA-318 Board)
Mode
E-E (SP)
Note: A frequency counter should be connected through a buffer
amplifier (oscilloscope, etc.) having a high impedance and
a low capacitance.
[Check Method]
1) Check that the oscillation frequency satisfies the specified value
and that the oscillation voltage is 500 ± 200mVp-p.
Signal
Measurement point
No-signal
IC201 pin !•
Measuring instrument
Specified value
Oscilloscope
A=290 ± 70mVp-p
[Check Method]
1) Check that the recording RF signal satisfies the specified value.
A
500 ± 200mVp-p
3,579,545 ± 70Hz
Fig. 6-2-8.
Fig. 6-2-5.
6-4
2-4-4. Recording Chroma Level Check
(MA-318 Board)
Mode
Recording (SP)
Signal
Measurement point
Color bar
IC201 pin !¢
Measuring instrument
Specified value
Oscilloscope
A=380 ± 70mVp-p
2-5. AUDIO SYSTEM ADJUSTMENT
• For the adjustment of the audio system, perform in the SP mode
if there is no special notes. Use the alignment tape.
[Connecting Instruments]
Audio line OUTPUT L/R
Audio line INPUT L/R
[Check Method]
1) Confirm the amplitude of recording chroma level becomes the
specified value.
Audio
oscillator
600 Ω
Audio level
meter
or
distortion
meter
47 kΩ
Attenuator
VTR
A
Fig. 6-2-11.
• Adjust in the SP mode if there is no special indications.
• Perform the adjustment setting the switch on the following
positions.
• INPUT SELECT switch .............................. LINE or LINE 1
(Remote commander)
Fig. 6-2-9.
2-4-5. Playback Level Check (MA-318 Board)
Mode
Playback
Signal Alignment
Measurement point
Alignment tape : SP mode color bar
portion
Video LINE OUT terminal
Measuring instrument
Specified value
Oscilloscope
A=1.0 ± 0.1Vp-p (75Ω terminated)
[Adjustment Method]
1. ACE head adjustment.....Refer to the VHS mechanical
adjustment manual (S MECHANISM)(9-921-647-11).
2. E-E output level check
3. Overall Output level and distortion factor check
4. Overall noise level check.
2-5-1. ACE Head Adjustment
Refer to the VHS mechanical adjustment manual
MECHANISM)(9-921-647-11).
[Check Method]
1) Check that the playback level satisfies the specified value.
White (100%)
2-5-2. E-E Output Level Check
A
Mode
Signal
E-E
400Hz, –7.5dBs : CJ570
Measurement point
Measuring instrument
CJ570
Audio level meter
Specified value
–7.5 ± 2dBs
[Check Method]
1) Input signal of 400Hz and –7.5dBs to the CJ461 L/R.
2) Check that the audio output level is –7.5 ± 3dBs.
H
Fig. 6-2-10.
6-5
(S
2-5-3. Overall Output Level and Distortion Factor
Check
Mode
Self-record playback
Signal
Measurement point
400Hz, –7.5dBs : CJ570
CJ570
Measuring instrument
Audio level meter and Distortion
meter
Playback Level: –7.5 ± 3dBs
Distortion: 4.0% or less
Specified value
[Check Method]
1) Input signal of 400Hz and –7.5dBs to the audio input.
2) Record signal.
3) Playback the recorded portion.
4) Check that the output level is –7.5 ± 3dBs.
5) Check that the distortion factor is 4.0% or less.
2-5-4. Overall Noise Level Check
Mode
Self-record playback
Signal
Measurement point
No signal (Insert a shorting plug into
the Audio LINE IN terminal)
CJ570
Measuring instrument
Specified value
Audio level meter
– 45.5dBs or less
[Check Method]
1) Record.
2) Playback recorded portion.
3) Check that noise level is – 45.5dBs or less.
2-6. TUNER SYSTEM ADJUSTMENT
2-6-1. Separation Adjustment (MA-318 Board)
Mode
Signal
E-E
RF signal
Video : Color bar
white (100%) modulation
Audio : L: 400Hz, R: 2kHz
30% modulation
Electrical field:
60-80dBm/75Ω terminated
Measuring instrument
Measuring point
Audio level meter
LINE OUT L
Adjusting element
Specified value
RV731
2kHz component minimum
[Adjustment Method]
1) Connect an audio level meter to LINE OUT L channel via HPF.
2) Feed the RF signal from RF IN terminal.
3) Adjust with RV731 so that the output level satisfies the specified
value.
6-6
2-7. ADJUSTING PARTS LOCATION DIAGRAM
MA-318 BOARD (CONDUCTOR SIDE)
CJ570 LINE IN/OUT
4
CN261
1 RF SW POS
AF SW POS
V
ste
Sy
o Adj
e
id
m
IC
20
1
40
41
25 2
4
64 6
5
1
CN341
AF SW POS
80
3
1
1
4
JS161
Q605
MTR12V
E
Q603
SW5V
RF SW POS
AF SW POS
E
6-8E
IC601
SW12V
RV731
SEPARATION
SLV-798HF/998HF
SECTION 7
REPAIR PARTS LIST
7-1. EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
Hardware (#mark) list is given in the last of
this parts list.
•
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
7-1-1. FRONT PANEL ASSEMBLY AND UPPER CASE SECTION
SLV-998HF
SLV-798HF
19
24
21
8
7
23
22
20
not supplied
not supplied
15
15
14
4
7
15
3
5
13
15
9
15
6
15
10
11
2
1
16
Ref. No.
Part No.
Description
1
2
3
3
* 4
3-979-310-01
3-979-309-01
X-3947-898-2
X-3947-899-2
A-6791-466-A
RING (AV), JOG
BUTTON (AV), CENTER
PANEL ASSY, FRONT (798HF)
PANEL ASSY, FRONT (998HF)
JK-159 BOARD, COMPLETE
Remarks
5
6
7
8
!9
3-953-432-01
3-979-302-02
3-710-901-11
3-979-313-01
1-777-854-21
SPRING (GE), FL
DOOR (AV), CASSETTE
SCREW, TAPPING
CASE, UPPER
CORD, POWER
* 10
11
* 13
A-6791-467-A DM-74 BOARD, COMPLETE
1-762-844-21 SWITCH, ROTARY
A-6791-465-A FR-130(A) BOARD, COMPLETE (798HF)
Ref. No.
Part No.
Description
* 13
14
15
16
19
A-6791-469-A
1-783-131-11
4-921-277-41
4-977-593-21
1-475-554-41
FR-130(B) BOARD, COMPLETE (998HF)
CABLE, FLAT (FFM-16)
SCREW (B2.6X8), TAPPING, BIND
RING (DIA. 50), ORNAMENTAL (797HF)
COMMANDER, STANDARD(RMT-V232C)
(798HF)
Remarks
20
21
3-709-129-01 COVER, BATTERY (798HF)
1-475-605-11 COMMANDER, STANDARD (RMT-V229)
22
23
24
3-709-126-01 COVER, BATTERY (998HF)
3-973-077-31 RING, CHANGE SPEED (998HF)
3-972-850-01 BUTTON, FUNCTION (998HF)
(998HF)
7-1
7-1-2. CHASSIS SECTION
57
#1
#2
54
#1
#1
Q102
53
56
Q101
53
57
52
55
57
51
51
Not supplied
Ref. No.
Part No.
51
* 52
* 52
3-979-314-01 BASE (R), MD
A-6791-464-A MA-318(A) BOARD, COMPLETE (798HF)
A-6791-468-A MA-318(B) BOARD, COMPLETE
(998HF; US, Canadian, Mexican)
A-6791-541-A MA-318(B) BOARD, COMPLETE
(998HF; Chilean, PX)
3-960-273-01 SPACER, TOP END
* 52
53
Description
Remarks
Ref. No.
Part No.
Description
! 54
! 54
* 55
56
57
1-468-281-11
1-468-282-11
3-979-564-01
1-779-725-11
3-970-608-21
POWER BLOCK SR801 (EXCEPT Chilean, PX)
POWER BLOCK SR709 (Chilean, PX)
PANEL, REAR
CONNECTOR, BOARD TO BOARD 5P
SUMITITE (B3), +BV
7-2
Q101
Q102
Remarks
8-729-043-84 TRANSISTOR PT380F3
8-729-043-84 TRANSISTOR PT380F3
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
7-1-3. MECHANISM DECK-1
707
#701
710
708
709
706
not
supplied
723
704
712
711
703
705
702
722
701
713
720
701
716
721
714
719
715
717
718
#701
Ref. No.
724
Part No.
Description
Part No.
Description
701
702
703
704
705
3-977-509-01
3-977-507-01
3-977-508-01
1-500-144-11
3-977-495-01
WASHER, THRUST
TABLE, REEL (S) (GRAY)
TABLE, REEL (T) (BLACK)
HEAD, FE
SHAFT TG2
Remarks
Ref. No.
713
714
715
716
717
3-977-447-01
3-977-514-01
3-977-441-01
3-977-445-01
3-977-465-01
GEAR, ELEVATOR
OPENER, LID
GEAR, PINCH PRESSING
GEAR, TG8 ARM DRIVING
SPRING,EXTENSION(RVS BRAKE)
706
707
708
709
710
3-977-494-01
A-6759-619-C
3-977-535-01
3-977-536-01
3-970-471-01
HOLDER, FEH
FL COMPLETE ASSY
PLATE, LUMINOUS(END SENSOR)
PLATE, LUMINOUS(TOP SENSOR)
SPRING (DECK OPEN), TORSION
718
719
720
721
722
X-3947-582-1
3-977-446-01
X-3947-590-1
A-6759-620-A
3-974-556-01
ARM ASSY, RVS BRAKE
GEAR, TG8 ARM
TG8 ASSY
HEAD BLOCK ASSY, ACE (TDK)
+ HEXA TT 2.6X9 (TAPER)
711
712
A-6759-615-A PRESS BLOCK ASSY, PINCH
3-958-455-01 SPRING (PINCH), TENSION
723
724
3-979-508-01 SCREW
3-978-485-01 PLATE, GUIDE CASSETTE
7-3
Remarks
7-1-4. MECHANISM DECK-2
Note: There are two types of drum assembly in models for
service.
#701
[Discrimination]
767
No. 768-770
—Top View—
776 (Note)
768
771
769
772
770
773
There are two printed circuit
boards on the top.
761
No. 776
—Top View—
764
760
763
758
759
#701
762
762
774
763
757
There is no printed circuit board.
766
756
Note: It cannot be divided to two
parts, the upper and the
lower drum assemblies.
#702
775
765
755
754
752
753
751
Ref. No.
Part No.
Description
751
752
753
754
755
X-3947-581-1
3-977-462-01
X-3947-573-1
X-3947-580-2
3-977-513-02
BRAKE ASSY,MAIN(T)
SPRING,EXTENTION. (MAIN BRAKE)
ARM ASSY, PENDULUM
BRAKE ASSY, MAIN(S)
LEVER, REC. PROOF
756
757
758
759
760
3-976-767-01
3-977-487-01
X-3947-587-1
X-3947-589-1
3-977-488-01
SPRING, TENS. (REC. PROOF)
BOSS, TG1 FULCRUM
TG1 ASSY
BAND ASSY, TG1
SPRING (POWER TENSION)
761
762
763
764
765
A-6750-324-A
X-3944-378-1
3-965-178-01
3-969-632-04
A-6750-325-A
SHUTTLE (S) BLOCK ASSY
ROLLER ASSY, GUIDE
SPRING
BASE, DRUM
SHUTTLE (T) BLOCK ASSY
Remarks
Ref. No.
766
767
768
769
Description
Remarks
769
PLATE, LUMINOUS
GROUND ASSY, SHAFT
SCREW
DRUM ASSY, UPPER DZR-45-R
(EXCEPT 998HF)(Note)
8-848-594-02 DRUM ASSY, UPPER DZR-51-R (998HF)(Note)
770
771
772
773
774
8-848-666-11
A-6746-074-G
X-3947-255-1
3-975-724-07
X-3946-855-1
775
776
X-3946-856-1 SHUTTLE (T) ASSY
8-839-044-02 DRUM ASSY DZH-94A/Z-RP (M901)
(EXCEPT 998HF)(Note)
8-839-046-02 DRUM ASSY DZH-96A-R (M901)(998HF)(Note)
776
7-4
Part No.
3-977-501-01
X-3943-899-8
2-643-205-01
8-848-576-02
DRUM ASSY, LOWER DZL-51B/J-RP (M901)
ROLLER BLOCK ASSY, HC
ROLLER ASSY, HC
ARM, HC
SHUTTLE (S) ASSY
7-1-5. MECHANISM DECK-3
816
815
817
M902
803
818
803
814
#701
812
813
828
811
829
820
810
808
809
819
827
821
826
807
805
822
806
804
823
824
830
M903
803
801
825
802
Ref. No.
Remarks
#703
Ref. No.
Part No.
Description
Part No.
Description
801
802
803
804
805
3-977-437-01
X-3947-584-1
3-977-443-01
3-977-438-01
3-977-506-01
RETAINER,CAM MOTOR
ASSY, REEL DIRECT
WASHER, STOPPER
WORM - WHEEL
ARM, LIMITTER SELECTION
817
818
819
820
821
3-977-439-01
3-977-442-01
3-977-455-01
3-977-456-03
X-3947-579-1
GEAR, CAM
SLIDER
GEAR, LOADING(T)
SPRING, TORSION (LOAD T)
LEVER ASSY, LOADING(T)
806
807
808
809
810
3-977-444-01
3-977-515-01
3-977-517-01
3-977-519-01
3-977-518-02
GEAR, PINCH TRANSMISSION
GUIDE, FL SLIDER
PLATE, SLIDE, FL
SPRING, TENS. (LIMIT, FL)
PLATE, LIMITTER, FL
822
823
824
825
826
3-977-451-01
3-977-452-01
X-3947-578-1
X-3947-576-2
3-977-468-01
GEAR, LOADING(S)
SPRING, TORSION (LOAD S)
LEVER ASSY, LOADING(S)
CHASSIS ASSY, MECHANICAL
SHAFT, CAPSTAN BRAKE
811
812
813
814
815
3-977-516-01
3-977-877-01
3-977-504-01
X-3947-585-1
3-977-510-01
HOLDER, FL SLIDER
PLATE, RETAINER
GEAR, CLUTCH
GEAR ASSY, PULLEY
BELT, RUBBER
827
828
829
830
M902
3-977-467-02
X-3947-583-1
3-977-489-01
A-6759-616-A
1-698-971-11
SPRING, CAP BRAKE
BRAKE ASSY, CAPSTAN
ARM, TG1 DRIVING
GEAR BLOCK ASSY, LOADING
MOTOR, DC
816
3-977-440-01 WASHER, STOPPER
M903
X-3947-577-1 MOTOR ASSY, CAM
7-5
Remarks
DM-74
FR-130
7-2. ELECTRICAL PARTS LIST
NOTE:
•
When indicating parts by reference number,
please include the board name.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
•
•
•
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
-XX, -X mean standardized parts, so they may
have some difference from the original one.
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
CAPACITORS:
uF: µF
Ref. No.
Part No.
Description
Remarks
Ref. No.
*
A-6791-467-A DM-74 BOARD, COMPLETE
*********************
(Ref.No.: 2,000 Series)
< CONNECTOR >
CN440
CN441
1-770-031-11 CONNECTOR, BOARD TO BOARD 7P
1-770-514-41 CONNECTOR, FFC/FPC 5P
< DIODE >
D440
8-729-424-08 TRANSISTOR UN2111
R441
R442
R443
R444
R445
1-216-057-00
1-216-057-00
1-216-061-00
1-216-065-91
1-216-057-00
R446
1-216-029-00 METAL CHIP
Description
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
2.2K
2.2K
3.3K
4.7K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C465
C466
C467
C468
C469
1-126-916-11
1-163-038-00
1-126-935-11
1-163-038-00
1-104-905-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CAPACITOR
1000uF
0.1uF
470uF
0.1uF
0.22F
20%
6.3V
25V
6.3V
25V
5.5V
C471
C472
C473
C474
C475
1-164-232-11
1-164-004-11
1-163-235-11
1-163-102-00
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
22PF
24PF
0.01uF
10%
5%
5%
50V
25V
50V
50V
50V
C476
C477
C478
C479
1-163-038-00
1-163-229-11
1-163-229-11
1-126-096-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
12PF
12PF
10uF
150
5%
1/10W
CN460
* CN461
20%
5%
5%
20%
25V
50V
50V
35V
1-695-392-31 PIN, CONNECTOR (PC BOARD) 31P
1-691-406-11 CONNECTOR, BOARD TO BOARD 7P
< DIODE >
D420
D460
D462
D463
8-719-110-03
8-719-056-07
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
RD7.5ES-B2
SLR-342MCT31
11ES2
11ES2
< IC >
S441
1-762-196-21 SWITCH, TACT (EJECT)
S442
1-762-196-21 SWITCH, TACT (REC)
S443
1-762-196-21 SWITCH, TACT (JOG)
S444
1-762-196-21 SWITCH, TACT (PAUSE)
************************************************************
IC460
IC461
IC462
IC463
A-6791-465-A FR-130(A) BOARD, COMPLETE (798HF)
*************************
A-6791-469-A FR-130(B) BOARD, COMPLETE (998HF)
*************************
(Ref.No.: 2,000 Series)
3-972-815-01 HOLDER (100), FL
*
Remarks
< CONNECTOR >
< SWITCH >
*
•
Part No.
< RESISTOR >
*
•
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
8-719-056-06 DIODE SLR-342DC3F
< TRANSISTOR >
Q440
•
8-752-891-14
8-749-011-22
8-759-432-34
8-759-248-87
IC
IC
IC
IC
CXP82960-057Q
GP1U27X
ST24W16FM6TR
MM1256XF-BE
< JUMPER RESISTOR >
JR401
JR402
JR403
JR404
JR405
1-216-296-00
1-216-295-00
1-216-296-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/8W
1/10W
1/10W
JR406
JR407
JR408
1-216-295-00 METAL CHIP
1-216-295-00 METAL CHIP
1-216-296-00 METAL CHIP
0
0
0
5%
5%
5%
1/10W
1/10W
1/8W
< BUZZER >
BZ460
1-529-104-11 BUZZER, PIEZOELECTRIC
< CAPACITOR >
< COIL >
C460
C461
C462
C463
C464
1-163-809-11
1-164-232-11
1-164-232-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
25V
50V
50V
50V
50V
L181
1-410-509-11 INDUCTOR
10uH
< FLUORESCENT INDICATOR >
ND420
7-6
1-517-716-11 INDICATOR TUBE, FLUORESCENT
FR-130
Ref. No.
Part No.
Description
Remarks
Ref. No.
< TRANSISTOR >
Q460
8-729-421-22 TRANSISTOR UN2211
< RESISTOR >
R404
R405
R406
R407
1-216-089-00
1-216-075-00
1-216-057-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
12K
2.2K
2.2K
R407
1-216-073-00 METAL CHIP
10K
R408
1-216-061-00 METAL CHIP
R409
5%
5%
5%
5%
JK-159
MA-318
Part No.
Description
S407
S408
S409
S410
S411
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (COMMAND MODE)(998HF)
SWITCH, TACT (EASY SET UP) (998HF)
SWITCH, TACT (CHANNEL:-)
SWITCH, TACT (CHANNEL:+)
SWITCH, TACT (REW)
Remarks
S412
1-762-196-21 SWITCH, TACT (FF)
1/10W
1/10W
1/10W
1/10W
(998HF)
5%
1/10W
(797HF,798HF)
X460
1-760-494-11 VIBRATOR, CRYSTAL 16MHz
X461
1-579-463-11 VIBRATOR, CRYSTAL 32.768kHz
************************************************************
3.3K
5%
*
1-216-065-91 RES,CHIP
4.7K
5%
R410
R411
1-216-075-00 METAL CHIP
1-216-057-00 METAL CHIP
12K
2.2K
5%
5%
1/10W
(998HF)
1/10W
(998HF)
1/10W
1/10W
R412
R413
R415
R416
R417
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R420
R460
R461
R462
R463
1-216-069-00
1-216-029-00
1-216-089-00
1-216-049-00
1-216-089-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.8K
150
47K
1K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R464
R465
R466
R467
R468
1-216-049-00
1-216-049-00
1-216-073-00
1-216-073-00
1-216-113-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R469
R470
R471
R472
R474
1-216-073-00
1-216-073-00
1-216-025-91
1-216-025-91
1-216-113-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
10K
10K
100
100
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R475
R476
R477
R478
R479
1-216-295-00
1-216-295-00
1-216-095-00
1-216-113-00
1-216-049-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
82K
470K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R480
R481
R482
R483
R484
1-216-049-00
1-216-049-00
1-216-049-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R485
1-216-113-00 METAL CHIP
470K
5%
1/10W
< VIBRATOR >
A-6791-466-A JK-159 BOARD, COMPLETE
**********************
(Ref.No.: 2,000 Series)
< CAPACITOR >
C806
1-163-009-11 CERAMIC CHIP
0.001uF
10%
50V
< JACK >
CJ801
1-774-509-11 JACK, PIN 3P (VIDEO,AUDIO LINE-2 IN)
< CONNECTOR >
CN801
1-506-484-11 PIN, CONNECTOR 5P
< DIODE >
D801
D802
D803
D804
8-719-108-12
8-719-108-12
8-719-109-84
8-719-108-12
DIODE
DIODE
DIODE
DIODE
RD9.1E-W
RD9.1E-W
RD5.1ES-B1
RD9.1E-W
< RESISTOR >
R801
1-216-295-00 METAL CHIP
0
5%
1/10W
R802
1-216-295-00 METAL CHIP
0
5%
1/10W
R803
1-216-022-00 METAL CHIP
75
5%
1/10W
************************************************************
A-6791-464-A MA-318(A) BOARD, COMPLETE (798HF)
*************************
A-6791-468-A MA-318(B) BOARD, COMPLETE
*************************
(998HF: US, Canadian, Mexican)
*
*
*
A-6791-541-A MA-318(B) BOARD, COMPLETE
*************************
(998HF: Chilean, PX)
(Ref.No.: 1,000 Series)
*
*
3-960-273-01 SPACER, TOP END
3-960-274-01 SPACER, LED
< CAPACITOR >
< SWITCH >
S402
S403
S404
S405
S406
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (POWER)
SWITCH, TACT (EDIT)
SWITCH, TACT (SP/EP)
SWITCH, TACT (TV/VIDEO)
SWITCH, TACT (INPUT SELECT)
7-7
C101
C102
C103
C104
C105
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-128-057-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
0.001uF
0.001uF
0.001uF
330uF
10%
10%
10%
10%
20%
50V
50V
50V
50V
6.3V
C106
C108
C109
C118
C119
1-124-589-11
1-164-004-11
1-164-004-11
1-137-441-11
1-126-157-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
47uF
0.1uF
0.1uF
0.027uF
10uF
20%
10%
10%
5%
20%
16V
25V
25V
50V
16V
MA-318
Ref. No.
Part No.
Description
C120
C121
C122
C123
C140
1-164-232-11
1-124-463-00
1-126-154-11
1-130-489-00
1-126-933-11
CERAMIC CHIP
ELECT
ELECT
MYLAR
ELECT
0.01uF
0.1uF
47uF
0.033uF
100uF
Remarks
Part No.
Description
20%
20%
5%
20%
50V
50V
6.3V
50V
16V
C142
C143
C144
C145
C146
1-126-933-11
1-109-982-11
1-163-018-00
1-126-967-11
1-163-263-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
C147
C149
C150
C151
C152
1-109-982-11
1-164-232-11
1-126-967-11
1-163-121-00
1-164-161-11
C252
C253
C254
C255
C256
1-164-232-11
1-164-004-11
1-163-038-00
1-163-038-00
1-163-038-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
1uF
0.0056uF
47uF
330PF
20%
10%
5%
20%
5%
16V
10V
50V
16V
50V
C260
C261
C262
1-163-229-11 CERAMIC CHIP
1-163-229-11 CERAMIC CHIP
1-163-099-00 CERAMIC CHIP
12PF
12PF
18PF
5%
5%
5%
C263
1-163-099-00 CERAMIC CHIP
18PF
5%
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
0.01uF
47uF
150PF
0.0022uF
10%
10V
50V
16V
50V
100V
C264
C265
C266
C267
1-163-037-11
1-163-037-11
1-164-232-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.01uF
0.022uF
10%
10%
10%
25V
25V
50V
25V
C153
C160
C161
C162
C163
1-164-161-11
1-164-232-11
1-163-229-11
1-163-229-11
1-126-154-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.0022uF
0.01uF
12PF
12PF
47uF
5%
5%
20%
100V
50V
50V
50V
6.3V
C268
C269
C270
C271
C272
1-163-235-11
1-163-235-11
1-163-037-11
1-163-037-11
1-163-099-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
22PF
0.022uF
0.022uF
18PF
5%
5%
10%
10%
5%
50V
50V
25V
25V
50V
C164
C165
C166
C172
C201
1-164-232-11
1-163-038-00
1-164-004-11
1-124-584-00
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
100uF
1uF
10%
20%
10%
50V
25V
25V
10V
10V
C273
C274
C276
C277
C278
1-163-099-00
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
18PF
0.022uF
0.022uF
0.022uF
0.022uF
5%
10%
10%
10%
10%
50V
25V
25V
25V
25V
C202
C204
C205
C206
C207
1-163-809-11
1-164-232-11
1-163-037-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.01uF
0.022uF
0.01uF
0.01uF
10%
25V
50V
25V
50V
50V
C279
C280
C281
C282
C283
1-163-037-11
1-124-584-00
1-164-346-11
1-164-232-11
1-163-038-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
100uF
1uF
0.01uF
0.1uF
10%
20%
25V
10V
16V
50V
25V
C209
C210
C214
C217
C219
1-124-248-00
1-163-131-00
1-163-124-00
1-109-982-11
1-164-159-21
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
22uF
390PF
200PF
1uF
0.1uF
20%
5%
5%
10%
35V
50V
50V
10V
50V
C284
C285
C286
C287
C288
1-163-038-00
1-162-306-11
1-124-584-00
1-163-227-11
1-163-227-11
CERAMIC CHIP
CERAMIC
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
100uF
10PF
10PF
C220
C222
C223
C226
C228
1-109-982-11
1-163-038-00
1-124-589-11
1-163-038-00
1-124-261-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
1uF
0.1uF
47uF
0.1uF
10uF
10%
20%
10V
25V
16V
25V
50V
C289
C301
C305
C306
C307
1-163-038-00
1-164-159-21
1-126-160-11
1-126-160-11
1-126-964-11
CERAMIC CHIP
CERAMIC
ELECT
ELECT
ELECT
0.1uF
0.1uF
1uF
1uF
10uF
C229
C230
C231
C232
C233
1-164-159-21
1-124-589-11
1-124-261-00
1-109-982-11
1-109-982-11
CERAMIC
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
47uF
10uF
1uF
1uF
20%
20%
10%
10%
50V
16V
50V
10V
10V
C308
C309
C310
C311
C312
1-126-967-11
1-126-963-11
1-163-009-11
1-163-014-00
1-164-232-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
4.7uF
0.001uF
0.0027uF
0.01uF
20%
20%
10%
10%
16V
50V
50V
50V
50V
C234
C235
C236
C237
C238
1-164-232-11
1-164-232-11
1-109-982-11
1-164-232-11
1-164-159-21
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
0.01uF
0.01uF
1uF
0.01uF
0.1uF
50V
50V
10V
50V
50V
C313
C314
C315
C317
C318
1-124-261-00
1-164-232-11
1-126-160-11
1-126-163-11
1-126-967-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
10uF
0.01uF
1uF
4.7uF
47uF
20%
50V
50V
50V
50V
16V
C240
C241
C242
C243
C245
1-109-982-11
1-163-037-11
1-109-982-11
1-164-232-11
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.022uF
1uF
0.01uF
0.047uF
10%
10%
10%
10V
25V
10V
50V
25V
C331
C332
C333
C334
1-164-232-11
1-164-232-11
1-124-589-11
1-137-374-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
FILM
0.01uF
0.01uF
47uF
0.047uF
20%
5%
C246
C247
C248
C250
C251
1-109-982-11
1-163-809-11
1-164-232-11
1-163-038-00
1-163-038-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.047uF
0.01uF
0.1uF
0.1uF
10%
10%
10V
25V
50V
25V
25V
C334
1-137-462-11 FILM
0.018uF
5%
C340
C341
C342
1-164-232-11 CERAMIC CHIP
1-124-589-11 ELECT
1-164-004-11 CERAMIC CHIP
0.01uF
47uF
0.1uF
20%
10%
20%
5%
10%
10%
10%
20%
10%
10%
Ref. No.
7-8
Remarks
0.01uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
50V
25V
25V
25V
25V
50V
50V
50V
(998HF)
50V
(998HF)
30%
20%
0.5PF
0.5PF
25V
16V
10V
50V
50V
20%
20%
20%
25V
50V
50V
50V
50V
20%
20%
20%
50V
50V
16V
50V
(798HF)
100V
(998HF)
50V
16V
25V
MA-318
Ref. No.
Part No.
Description
C346
C350
C352
C353
C357
1-164-232-11
1-164-004-11
1-163-009-11
1-163-038-00
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.001uF
0.1uF
0.001uF
Remarks
Part No.
Description
50V
25V
50V
25V
50V
C623
C624
C625
C626
C627
1-126-967-11
1-124-589-11
1-126-967-11
1-128-131-11
1-128-131-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
47uF
47uF
22uF
22uF
C358
C359
C361
C362
C363
1-164-004-11
1-164-232-11
1-164-222-11
1-164-222-11
1-126-960-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.01uF
0.22uF
0.22uF
1uF
20%
25V
50V
25V
25V
50V
C628
C629
C701
C704
C706
1-164-232-11
1-126-966-11
1-126-967-11
1-164-232-11
1-126-963-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.01uF
33uF
47uF
0.01uF
4.7uF
C364
C365
C366
C369
C370
1-126-960-11
1-126-960-11
1-126-960-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
1uF
1uF
1uF
10uF
10uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C707
C709
C710
C712
C735
1-164-161-11
1-126-933-11
1-164-232-11
1-126-933-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.0022uF
100uF
0.01uF
100uF
10uF
10%
20%
C371
C372
C373
C374
C375
1-126-964-11
1-126-964-11
1-126-964-11
1-126-960-11
1-164-004-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
10uF
10uF
10uF
1uF
0.1uF
20%
20%
20%
20%
10%
50V
50V
50V
50V
25V
C736
C802
C803
C804
C805
1-126-967-11
1-163-263-11
1-163-243-11
1-163-091-00
1-163-037-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
330PF
47PF
8PF
0.022uF
20%
5%
5%
C377
C378
C379
C380
C381
1-126-967-11
1-126-964-11
1-126-961-11
1-126-964-11
1-126-967-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
10uF
2.2uF
10uF
47uF
20%
20%
20%
20%
20%
16V
50V
50V
50V
16V
C806
C807
C808
C809
C810
1-163-087-00
1-164-232-11
1-163-127-00
1-163-037-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4PF
0.01uF
270PF
0.022uF
0.01uF
C383
C384
C385
C386
C391
1-164-004-11
1-164-232-11
1-126-967-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
47uF
0.01uF
0.01uF
10%
25V
50V
16V
50V
50V
C811
C812
C813
C814
C815
1-163-038-00
1-163-237-11
1-164-232-11
1-163-257-11
1-124-589-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
27PF
0.01uF
180PF
47uF
C398
C399
C501
C502
C503
1-163-016-00
1-163-016-00
1-164-489-11
1-124-589-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.0039uF
0.0039uF
0.22uF
47uF
0.01uF
10%
10%
10%
20%
50V
50V
16V
16V
50V
C816
C817
C830
1-163-038-00 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
0.1uF
0.01uF
0.01uF
C832
1-163-251-11 CERAMIC CHIP
100PF
5%
C504
C505
C506
C507
C508
1-164-004-11
1-126-157-11
1-164-232-11
1-163-038-00
1-163-239-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.01uF
0.1uF
33PF
10%
20%
25V
16V
50V
25V
50V
C833
1-163-121-00 CERAMIC CHIP
150PF
5%
C834
1-163-245-11 CERAMIC CHIP
56PF
5%
C509
C511
C512
C513
C514
1-164-505-11
1-163-229-11
1-163-235-11
1-164-232-11
1-163-235-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
12PF
22PF
0.01uF
22PF
C835
1-163-038-00 CERAMIC CHIP
0.1uF
C836
1-124-589-11 ELECT
47uF
C837
1-163-038-00 CERAMIC CHIP
0.1uF
C515
C516
C517
C518
C519
1-124-589-11
1-126-160-11
1-163-239-11
1-124-257-00
1-163-139-00
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
47uF
1uF
33PF
2.2uF
820PF
C520
C521
C522
C523
C560
1-163-038-00
1-164-232-11
1-163-037-11
1-163-037-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.022uF
0.022uF
0.001uF
C561
C563
C564
C621
C622
1-126-935-11
1-124-589-11
1-164-232-11
1-164-232-11
1-126-965-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
470uF
47uF
0.01uF
0.01uF
22uF
10%
10%
10%
10%
20%
5%
Ref. No.
Remarks
5%
16V
50V
50V
50V
50V
20%
20%
5%
20%
5%
16V
50V
50V
50V
50V
C851
C852
C853
C854
1-164-232-11
1-163-038-00
1-163-243-11
1-163-239-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
47PF
33PF
10%
10%
10%
25V
50V
25V
25V
50V
C855
C859
C871
C872
C873
1-163-243-11
1-124-589-11
1-124-589-11
1-163-019-00
1-164-232-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
47PF
47uF
47uF
0.0068uF
0.01uF
6.3V
16V
50V
50V
50V
C874
C875
C876
C878
C880
1-163-038-00
1-164-346-11
1-163-135-00
1-163-038-00
1-163-099-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
560PF
0.1uF
18PF
5%
5%
20%
20%
20%
7-9
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
10%
5%
10%
5%
5%
20%
16V
16V
16V
50V
50V
50V
16V
16V
50V
50V
100V
16V
50V
16V
50V
16V
50V
50V
50V
25V
50V
50V
50V
25V
50V
25V
50V
50V
50V
16V
25V
50V
50V
(998HF)
20%
5%
5%
5%
20%
20%
10%
5%
5%
50V
(998HF)
50V
(998HF)
50V
(998HF)
25V
(998HF)
16V
(998HF)
25V
(998HF)
50V
25V
50V
50V
50V
16V
16V
50V
50V
25V
16V
50V
25V
50V
MA-318
Ref. No.
Part No.
Description
C881
C913
1-163-099-00 CERAMIC CHIP
1-163-011-11 CERAMIC CHIP
18PF
5%
0.0015uF 10%
C932
1-164-232-11 CERAMIC CHIP
0.01uF
C933
1-126-967-11 ELECT
47uF
20%
C934
1-104-697-11 FILM
0.047uF
5%
C935
1-163-251-11 CERAMIC CHIP
100PF
5%
C980
C981
C982
C983
1-163-038-00
1-126-967-11
1-163-038-00
1-163-038-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
C984
C985
C986
1-163-009-11 CERAMIC CHIP
1-163-017-00 CERAMIC CHIP
1-163-038-00 CERAMIC CHIP
0.1uF
47uF
0.1uF
0.1uF
20%
0.001uF 10%
0.0047uF 5%
0.1uF
Remarks
Ref. No.
Part No.
Description
50V
50V
(998HF)
50V
(998HF)
D801
D802
D980
D981
D982
8-719-971-05
8-719-911-19
8-719-110-08
8-719-110-08
8-719-911-19
DIODE
DIODE
DIODE
DIODE
DIODE
16V
(998HF)
100V
(998HF)
50V
(998HF)
D983
D984
8-719-110-08 DIODE RD8.2ES-B2
8-719-110-08 DIODE RD8.2ES-B2
25V
16V
25V
25V
50V
50V
25V
Remarks
HSM123
1SS119
RD8.2ES-B2
RD8.2ES-B2
1SS119
< IC >
IC100
IC101
IC140
IC141
IC161
8-759-702-02
8-759-481-46
8-759-100-93
8-759-438-83
8-752-891-10
IC
IC
IC
IC
IC
NJM062M
LB1943
uPC393G2
BA6305F-E2
CXP87948-006Q
IC201
IC202
IC260
IC301
IC340
8-759-488-74
8-759-439-51
8-759-352-17
8-759-499-30
8-759-486-92
IC
IC
IC
IC
IC
LA71534M-MPB
LC89978M-TE-L
HA118195NT
BA7755AF-E2
LA7256
IC360
IC500
IC501
IC601
IC733
8-759-486-64
8-759-443-82
8-759-164-09
8-759-438-18
8-742-037-00
IC
IC
IC
IC
HY
TDA9615H/N1,557
MB90089PF-G-178-ER-JK
LA7218M-TE-R
PQ12RD08
B IC SBX1837-51
IC871
IC980
8-759-430-84 IC MC68HC05CCVFB-LSC86145FB
8-759-356-27 IC NJM2129M-TE2
< JACK >
CJ570
1-779-011-11 JACK, PIN 6P
(VIDEO,AUDIO LINE-1 IN/LINE OUT)
< CONNECTOR >
CN101
CN102
* CN103
CN162
CN163
1-779-724-11
1-779-723-11
1-766-716-11
1-568-845-11
1-506-469-11
CONNECTOR, BOARD TO BOARD 5P
CONNECTOR, BOARD TO BOARD 9P
CONNECTOR, BOARD TO BOARD 3P
PIN, CONNECTOR (PC BOARD) 31P
PIN, CONNECTOR 4P
CN260
* CN261
CN301
CN302
* CN341
1-766-986-11
1-560-892-00
1-506-471-11
1-506-468-11
1-560-891-00
CONNECTOR, FFC/FPC 13P
PIN, CONNECTOR 4P
PIN, CONNECTOR 6P
PIN, CONNECTOR 3P (798HF)
PIN, CONNECTOR 3P
CN423
* CN602
CN603
1-506-470-11 PIN, CONNECTOR 5P
1-568-938-11 PIN, CONNECTOR 11P (998HF: Chilean, PX)
1-569-337-11 CONNECTOR, BOARD TO BOARD 11P
(EXCEPT 998HF: Chilean, PX)
1-506-468-11 PIN, CONNECTOR 3P (998HF)
CN931
< JUMPER RESISTOR >
< JACK >
CNJ980 1-779-013-11 JACK, MINIATURE (CONTROL S IN)
CNJ981 1-784-598-11 JACK (CONTROL S OUT)
< DIODE >
D103
D107
D109
D161
D370
8-719-048-26
8-719-911-19
8-719-200-82
8-719-200-82
8-719-110-08
DIODE
DIODE
DIODE
DIODE
DIODE
GL528V1
1SS119
11ES2
11ES2
RD8.2ES-B2
D379
D502
D503
D504
D560
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
8-719-109-74
DIODE
DIODE
DIODE
DIODE
DIODE
1SS119
1SS119
1SS119
1SS119
RD4.3ES-B1
D561
D611
D612
D614
D702
8-719-109-74
8-719-911-19
8-719-109-85
8-719-911-19
8-719-150-92
DIODE
DIODE
DIODE
DIODE
DIODE
RD4.3ES-B1
1SS119
RD5.1ES-B2
1SS119
RD33ES-T1B
7-10
JR001
JR002
JR004
JR005
JR006
1-216-295-00
1-216-296-00
1-216-295-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/8W
1/10W
1/8W
1/8W
JR007
JR008
JR009
JR010
JR011
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/8W
1/8W
JR012
JR013
JR014
JR015
JR016
1-216-296-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/8W
1/8W
1/10W
JR017
JR018
JR019
JR020
JR021
1-216-296-00
1-216-296-00
1-216-295-00
1-216-296-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/10W
1/8W
1/10W
JR022
JR023
JR024
JR025
JR026
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/10W
1/10W
JR027
JR028
JR029
JR030
JR031
1-216-295-00
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/8W
MA-318
Ref. No.
Part No.
Description
JR032
JR033
JR034
JR035
JR036
1-216-296-00
1-216-295-00
1-216-296-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
Remarks
1/8W
1/10W
1/8W
1/10W
1/8W
JR037
JR038
JR039
JR040
JR041
1-216-296-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/8W
1/8W
1/8W
JR043
JR044
JR045
JR046
JR047
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/10W
1/8W
JR048
JR049
JR050
1-216-296-00 METAL CHIP
1-216-296-00 METAL CHIP
1-216-295-00 METAL CHIP
0
0
0
5%
5%
5%
1/8W
1/8W
1/10W
5%
1/10W
Ref. No.
1-216-295-00 METAL CHIP
0
! PS101
! PS331
! PS600
1-414-936-21
1-414-189-31
1-414-189-31
1-414-934-21
1-414-940-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
22uH
100uH
100uH
10uH
100uH
L260
L262
L263
L264
L331
1-414-934-21
1-414-940-21
1-414-940-21
1-414-934-21
1-414-940-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH (998HF)
100uH
100uH
10uH (998HF)
100uH
L341
L501
L502
L503
L560
1-414-940-21
1-414-936-21
1-414-940-21
1-414-940-21
1-414-940-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
22uH
100uH
100uH
100uH
L604
L605
L606
L607
L703
1-410-519-11
1-414-930-21
1-414-934-21
1-414-930-21
1-414-930-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
68uH
2.2uH
10uH
2.2uH
2.2uH
L704
L731
L801
L803
L804
1-414-938-21
1-414-938-21
1-410-524-41
1-414-946-21
1-414-946-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
47uH
47uH
180uH
39uH
39uH
L805
L830
L831
L871
L931
1-414-939-21
1-414-933-11
1-414-940-21
1-414-934-21
1-410-687-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
68uH
6.8uH (998HF)
100uH (998HF)
10uH
1.2mH (998HF)
< PHOTO INTERRUPTER >
PH101
PH102
Remarks
1-533-586-31 LINK, IC
1-533-586-31 LINK, IC
1-532-841-21 LINK, IC
(998HF)
< TRANSISTOR >
< COIL >
L101
L140
L141
L160
L204
Description
< IC LINK >
< JUMPER RESISTOR >
JS609
Part No.
8-749-013-23 PHOTO INTERRUPTER GP3S120
8-749-013-23 PHOTO INTERRUPTER GP3S120
7-11
Q101
Q102
Q103
Q140
Q201
8-729-043-84
8-729-043-84
8-729-281-53
8-729-901-06
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
PT380F3
PT380F3
2SC1815-GR
DTA144EK
2SC2712-G
Q205
Q208
Q209
Q210
Q211
8-729-421-19
8-729-230-49
8-729-216-21
8-729-230-49
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN2213
2SC2712-G
2SA1162Y-TE85L
2SC2712-G
2SC2712-G
Q260
Q301
Q331
Q379
Q386
8-729-230-49
8-729-281-53
8-729-802-91
8-729-216-22
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712-G
2SC1815-GR
2SD879
2SA1162
2SC2712-G
Q387
Q502
Q503
Q505
Q560
8-729-230-49
8-729-010-05
8-729-010-05
8-729-010-05
8-729-010-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712-G
MSB709-RT1
MSB709-RT1
MSB709-RT1
MSB709-RT1
Q603
Q604
Q605
Q606
Q731
8-729-018-99
8-729-010-29
8-729-140-93
8-729-119-78
8-729-421-19
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2394-F
MSD601-RST1
2SB733-34
2SC2785-HFE
UN2213
Q801
Q802
Q803
Q804
Q805
8-729-216-21
8-729-230-49
8-729-216-21
8-729-230-49
8-729-900-51
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1162Y-TE85L
2SC2712-G
2SA1162Y-TE85L
2SC2712-G
DTA114TK
Q806
Q807
Q808
Q809
Q810
8-729-230-49
8-729-230-49
8-729-230-49
8-729-900-51
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712-G
2SC2712-G
2SC2712-G
DTA114TK
2SC2712-G
Q830
Q831
Q832
Q833
Q834
8-729-216-22
8-729-216-22
8-729-421-19
8-729-804-41
8-729-421-19
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1162 (998HF)
2SA1162 (998HF)
UN2213 (998HF)
2SB1122-S (998HF)
UN2213 (998HF)
Q851
Q852
Q853
Q854
Q855
8-729-230-49
8-729-230-49
8-729-216-21
8-729-216-21
8-729-230-49
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712-G
2SC2712-G
2SA1162Y-TE85L
2SA1162Y-TE85L
2SC2712-G
Q856
Q857
Q871
Q872
Q873
8-729-230-49
8-729-216-21
8-729-010-05
8-729-010-29
8-729-010-29
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712-G
2SA1162Y-TE85L
MSB709-RT1
MSD601-RST1
MSD601-RST1
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
MA-318
Ref. No.
Q874
Q875
Q931
Q932
Part No.
Description
8-729-424-08
8-729-010-29
8-729-012-31
8-729-900-51
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Remarks
Ref. No.
UN2111
MSD601-RST1
2SC4040-TL2-Q (998HF)
DTA114TK (998HF)
Part No.
Description
R210
R213
R218
R219
R221
1-216-295-00
1-249-429-11
1-208-798-11
1-216-053-00
1-216-057-00
METAL CHIP
CARBON
RES,CHIP
METAL CHIP
METAL CHIP
0
10K
4.7K
1.5K
2.2K
5%
5%
0.50%
5%
5%
Remarks
1/10W
1/4W
1/10W
1/10W
1/10W
R222
R228
R229
R230
R231
1-216-051-00
1-216-057-00
1-216-055-00
1-216-045-00
1-216-071-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.2K
2.2K
1.8K
680
8.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R232
R234
R235
R236
R239
1-249-420-11
1-216-049-00
1-216-295-00
1-216-049-00
1-216-057-00
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.8K
1K
0
1K
2.2K
5%
5%
5%
5%
5%
1/4W F
1/10W
1/10W
1/10W
1/10W
R240
R247
R260
R261
R262
1-216-049-00
1-216-025-91
1-216-044-00
1-216-044-00
1-216-295-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
620
620
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R263
R264
R265
R266
R267
1-216-295-00
1-216-295-00
1-216-295-00
1-216-053-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
1.5K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R268
R269
R270
R271
R272
1-216-081-00
1-249-421-11
1-247-863-91
1-216-049-00
1-216-077-00
METAL CHIP
CARBON
CARBON
METAL CHIP
METAL CHIP
22K
2.2K
22K
1K
15K
5%
5%
5%
5%
5%
1/10W
1/4W F
1/4W
1/10W
1/10W
R273
R274
R275
R276
R301
1-216-077-00
1-216-073-00
1-216-073-00
1-216-049-00
1-216-093-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
10K
10K
1K
68K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R302
R306
R307
R309
R310
1-216-067-00
1-216-073-00
1-216-061-00
1-216-067-00
1-216-129-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
5.6K
10K
3.3K
5.6K
2.2M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R311
R312
R313
R314
R315
1-216-051-00
1-216-079-00
1-216-109-00
1-216-035-00
1-216-067-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.2K
18K
330K
270
5.6K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R316
R317
R318
R320
R331
1-216-071-00
1-216-079-00
1-216-075-00
1-216-047-91
1-217-671-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
8.2K
18K
12K
820
1
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R332
1-216-063-91 RES,CHIP
3.9K
5%
R332
1-216-067-00 METAL CHIP
5.6K
5%
R333
R334
1-249-401-11 CARBON
1-216-031-00 METAL CHIP
47
180
5%
5%
1/10W
(798HF)
1/10W
(998HF)
1/4W F
1/10W
R335
1-249-396-11 CARBON
18
5%
R341
R342
R344
1-216-049-00 METAL CHIP
1-216-049-00 METAL CHIP
1-216-055-00 METAL CHIP
1K
1K
1.8K
5%
5%
5%
< RESISTOR >
R101
R102
R103
R104
R105
1-249-413-11
1-216-089-00
1-249-437-11
1-216-085-00
1-216-085-00
CARBON
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
470
47K
47K
33K
33K
5%
5%
5%
5%
5%
1/4W F
1/10W
1/4W
1/10W
1/10W
R106
R107
R108
R109
R110
1-249-400-11
1-249-400-11
1-249-421-11
1-216-041-00
1-216-041-00
CARBON
CARBON
CARBON
METAL CHIP
METAL CHIP
39
39
2.2K
470
470
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W F
1/10W
1/10W
R111
R118
R119
R124
R125
1-216-041-00
1-216-089-00
1-216-077-00
1-249-421-11
1-249-421-11
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
CARBON
470
47K
15K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W F
1/4W F
R126
R127
R128
R129
R130
1-247-885-00
1-249-429-11
1-216-065-91
1-216-073-00
1-216-073-00
CARBON
CARBON
RES,CHIP
METAL CHIP
METAL CHIP
180K
10K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
1/10W
R131
R132
R133
R134
R135
1-208-806-11
1-208-806-11
1-249-436-11
1-216-089-00
1-216-089-00
RES,CHIP
RES,CHIP
CARBON
METAL CHIP
METAL CHIP
10K
10K
39K
47K
47K
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
R136
R137
R140
R141
R143
1-216-089-00
1-216-089-00
1-208-830-11
1-208-830-11
1-216-057-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
47K
47K
100K
100K
2.2K
5%
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R144
R145
R146
R148
R149
1-216-065-91
1-208-830-11
1-208-830-11
1-249-414-11
1-216-065-91
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
RES,CHIP
4.7K
100K
100K
560
4.7K
5%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/4W F
1/10W
R150
R151
R152
R153
R154
1-216-049-00
1-216-037-00
1-216-117-00
1-216-057-00
1-216-111-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
330
680K
2.2K
390K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R155
R160
R161
R162
R163
1-216-105-91
1-216-077-00
1-216-073-00
1-216-089-00
1-216-073-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
15K
10K
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R164
R165
R166
R167
R168
1-216-073-00
1-216-295-00
1-216-057-00
1-216-097-91
1-249-417-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
CARBON
10K
0
2.2K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W F
R169
R170
R201
R202
R203
1-216-073-00
1-216-073-00
1-216-041-00
1-216-069-00
1-216-049-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
470
6.8K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
7-12
1/4W F
(998HF)
1/10W
1/10W
1/10W
MA-318
Ref. No.
Part No.
Description
Part No.
Description
R346
R347
R348
R368
R370
1-216-065-91
1-216-065-91
1-216-033-00
1-216-133-00
1-216-065-91
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
4.7K
4.7K
220
3.3M
4.7K
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
R705
R706
R709
R710
R711
1-212-893-00
1-216-113-00
1-216-295-00
1-216-295-00
1-216-295-00
FUSIBLE
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
470K
0
0
0
5%
5%
5%
5%
5%
1/4W F
1/10W
1/10W
1/10W
1/10W
R371
R372
R373
R374
R378
1-208-820-11
1-216-065-91
1-216-033-00
1-216-033-00
1-249-434-11
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
CARBON
39K
4.7K
220
220
27K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
R712
R731
R732
R733
R735
1-216-295-00
1-216-049-00
1-216-049-00
1-249-425-11
1-216-049-00
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
0
1K
1K
4.7K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W F
1/10W
R379
R380
R381
R382
R383
1-216-049-00
1-216-025-91
1-216-025-91
1-216-295-00
1-216-295-00
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
1K
100
100
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R736
R737
R738
R739
R748
1-216-295-00
1-216-081-00
1-216-081-00
1-249-429-11
1-216-065-91
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
RES,CHIP
0
22K
22K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/10W
R384
R385
R386
R387
R389
1-216-091-00
1-216-091-00
1-216-049-00
1-216-049-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
56K
56K
1K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R749
R801
R802
R803
R804
1-216-049-00
1-216-049-00
1-216-049-00
1-216-039-00
1-216-039-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
390
390
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R391
R392
R393
R501
R502
1-216-049-00
1-216-049-00
1-216-295-00
1-216-295-00
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
0
0
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R805
R806
R807
R808
R809
1-216-049-00
1-216-043-91
1-216-039-00
1-216-033-00
1-216-077-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
560
390
220
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R505
R506
R507
R508
R510
1-216-059-00
1-216-051-00
1-216-081-00
1-216-049-00
1-216-081-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.7K
1.2K
22K
1K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R810
R811
R812
R813
R814
1-216-075-00
1-216-033-00
1-216-043-91
1-216-069-00
1-216-057-00
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
12K
220
560
6.8K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R514
R515
R517
R518
R519
1-216-073-00
1-216-101-00
1-216-063-91
1-216-043-91
1-216-043-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
150K
3.9K
560
560
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R815
R816
R817
R818
R819
1-216-067-00
1-216-075-00
1-216-077-00
1-216-039-00
1-216-045-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
5.6K
12K
15K
390
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R520
R521
R522
R523
R560
1-216-033-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-022-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
10K
10K
10K
75
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R820
R821
R822
R823
R824
1-216-039-00
1-216-045-00
1-216-049-00
1-216-041-00
1-216-043-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
390
680
1K
470
560
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R561
R562
R563
R565
R615
1-216-021-00
1-249-407-11
1-249-407-11
1-216-037-00
1-216-399-00
METAL CHIP
CARBON
CARBON
METAL CHIP
METAL OXIDE
68
150
150
330
6.8
5%
5%
5%
5%
5%
1/10W
1/4W F
1/4W F
1/10W
3W
F
R825
R826
R827
R828
R830
1-216-057-00
1-216-025-91
1-216-045-00
1-216-043-91
1-216-011-00
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
2.2K
100
680
560
27
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(998HF)
R617
R618
1-249-417-11 CARBON
1-249-413-11 CARBON
1K
470
R831
1-216-041-00 METAL CHIP
470
5%
R619
1-249-413-11 CARBON
470
R832
1-208-787-11 RES,CHIP
1.6K
R833
1-216-095-00 METAL CHIP
82K
R621
R622
R623
R624
R625
1-216-089-00
1-216-057-00
1-247-843-11
1-216-430-11
1-249-429-11
METAL CHIP
METAL CHIP
CARBON
METAL OXIDE
CARBON
47K
2.2K
3.3K
390
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1W
F
1/4W
R834
1-216-089-00 METAL CHIP
47K
R835
1-216-689-11 METAL CHIP
39K
R626
R627
R628
R701
R702
1-249-417-11
1-247-815-91
1-247-815-91
1-216-049-00
1-216-061-00
CARBON
CARBON
CARBON
METAL CHIP
METAL CHIP
1K
220
220
1K
3.3K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/10W
1/10W
5%
1/4W F
5%
1/4W F
(998HF: Chilean, PX)
5%
1/4W F
(998HF: Chilean, PX)
7-13
Remarks
1/10W
(998HF)
0.50% 1/10W
(998HF)
5%
1/10W
(998HF)
5%
1/10W
(998HF)
0.5% 1/10W
(998HF)
MA-318
Ref. No.
POWER BLOCK SR801
Part No.
Description
Remarks
R836
1-216-061-00 METAL CHIP
3.3K
5%
R837
1-216-073-00 METAL CHIP
10K 5%
1/10W
Ref. No.
Part No.
Description
Remarks
< TUNER >
1/10W
(998HF)
TU700
8-598-289-00 TUNER, FSS BTF-MA401
R844
R851
R852
1-216-069-00 METAL CHIP
1-208-820-11 RES,CHIP
1-208-802-11 RES,CHIP
6.8K
39K
6.8K
(998HF)
5%
1/10W
0.50% 1/10W
0.50% 1/10W
R853
R855
R856
R857
R858
1-208-792-11
1-208-770-11
1-208-758-11
1-208-790-11
1-216-051-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
2.7K
330
100
2.2K
1.2K
0.50%
0.50%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R859
R860
R861
R862
R864
1-208-800-11
1-216-057-00
1-216-065-91
1-208-806-11
1-216-057-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
5.6K
2.2K
4.7K
10K
2.2K
0.50%
5%
5%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R865
R871
R872
R873
R874
1-216-107-00
1-249-429-11
1-247-807-31
1-247-807-31
1-247-807-31
METAL CHIP
CARBON
CARBON
CARBON
CARBON
270K
10K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/4W
1/4W
R875
R876
R877
R878
R879
1-247-807-31
1-216-081-00
1-216-057-00
1-216-073-00
1-249-417-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
100
22K
2.2K
10K
1K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/4W F
R880
R881
R882
R883
R884
1-249-429-11
1-216-043-91
1-216-049-00
1-216-053-00
1-216-047-91
CARBON
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
10K
560
1K
1.5K
820
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
R885
R886
R887
R888
R889
1-247-807-31
1-216-073-00
1-216-081-00
1-216-081-00
1-247-807-31
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
100
10K
22K
22K
100
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/4W
D103
D104
D105
D106
D107
8-719-920-32
8-719-109-61
8-719-911-19
8-719-904-05
8-719-904-05
DIODE
DIODE
DIODE
DIODE
DIODE
ERA15-02
RD3.0ES
1SS119
1N4005
1N4005
R890
R931
1-216-049-00 METAL CHIP
1-249-394-11 CARBON
1K
12
5%
5%
R932
1-216-083-00 METAL CHIP
27K
5%
D108
D109
D110
D201
D202
8-719-904-05
8-719-904-05
8-719-904-05
8-719-061-02
8-719-510-73
DIODE
DIODE
DIODE
DIODE
DIODE
1N4005
1N4005
1N4005
PR1003
S3L20U
R934
1-216-073-00 METAL CHIP
10K
5%
1/10W
1/4W F
(998HF)
1/10W
(998HF)
1/10W
(998HF)
D204
D205
D206
D207
8-719-027-20
8-719-058-08
8-719-061-02
8-719-061-02
DIODE
DIODE
DIODE
DIODE
D3S4M
RD51F
PR1003
PR1003
< VIBRATOR >
X160
1-760-494-11 VIBRATOR, CRYSTAL 16MHz
X202
1-577-380-11 VIBRATOR, CRYSTAL 3.579545MHz
X500
1-577-381-11 VIBRATOR, CRYSTAL 14.31818MHz
X501
1-577-165-11 VIBLATOR, CERAMIC
X871
1-577-133-21 VIBRATOR, CRYSTAL
************************************************************
1-468-281-11 POWER BLOCK SR801 (EXCEPT Chilean, PX)
******************
(Ref. No.: 8,000 Series)
!
R980
R981
1-216-049-00 METAL CHIP
1-216-295-00 METAL CHIP
1K
0
5%
5%
< CAPACITOR >
! C101
! C102
C106
C107
C110
1-104-705-51
1-104-705-51
1-119-882-41
1-126-963-11
1-130-491-51
FILM
FILM
ELECT
ELECT
FILM
0.1uF
0.1uF
120uF
4.7uF
0.047uF
250V
250V
200V
50V
50V
C111
C201
C202
C203
C204
1-130-491-51
1-126-967-11
1-126-183-11
1-126-934-11
1-126-797-11
FILM
ELECT
ELECT
ELECT
ELECT
0.047uF
47uF
1000uF
220uF
1000uF
50V
50V
16V
16V
10V
C205
C206
C207
C208
1-126-925-11
1-126-967-11
1-126-925-11
1-126-960-11
ELECT
ELECT
ELECT
ELECT
470uF
47uF
470uF
1uF
10V
50V
10V
50V
< DIODE >
1/10W
1/10W
< VARIABLE RESISTOR >
RV731
1-241-766-11 RES, ADJ, CERMET 47K
< FUSE >
! F101
< SWITCH >
S101
S102
S701
T331
T331
T931
2A
125V
< FERRITE BEAD >
1-762-108-11 SWITCH, PUSH (1 KEY)(REC PROOF)
1-771-155-11 SWITCH, ROTARY (MECHANISM MODE)
1-571-588-11 SWITCH, SLIDE (3CH/4CH)
< TRANSFORMER >
1-533-296-11 FUSE
FB1
9-902-053-01 FERRITE BEAD
< IC >
! IC201
1-431-097-11 TRANSFORMER, BIAS OSCILLATION (798HF)
1-431-100-11 TRANSFORMER, BIAS OSCILLATION (998HF)
1-423-415-11 TRANSFORMER, BIAS OSCILLATION (998HF)
7-14
8-759-420-19 IC
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
AN1431T
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
POWER BLOCK SR801
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
1-777-854-21
1-762-844-21
1-783-131-11
1-468-281-11
1-468-282-11
MISCELLANEOUS
*************
CORD, POWER
SWITCH, ROTARY
CABLE, FLAT (FFM-16)
POWER BLOCK SR801 (EXCEPT Chilean, PX)
POWER BLOCK SR709 (Chilean, PX)
< PHOTOCOUPLER >
! PC101
8-719-018-29 PHOTOCOUPLER ON3131
!9
11
14
! 54
! 54
< TRANSISTOR >
Q101
Q102
8-729-904-98 TRANSISTOR
8-729-012-31 TRANSISTOR
2SC4054
2SC4040
56
704
721
769
< RESISTOR >
! R101
1-219-779-51 CARBON
6.8M
10%
1/2W
************************************************************
769
1-465-282-11 POWER BLOCK SR709 (Chilean, PX)
*******************
(Ref. No.: 9,000 Series)
!
< CAPACITOR >
! C101
! C102
C111
C112
C114
1-104-705-51
1-104-705-51
1-126-947-11
1-130-491-51
1-130-491-51
FILM
FILM
ELECT
FILM
FILM
0.1uF
0.1uF
47uF
0.1uF
0.1uF
250V
250V
35V
50V
50V
C115
C201
C202
C203
C204
1-130-491-51
1-128-552-11
1-126-183-11
1-126-934-11
1-126-183-11
FILM
ELECT
ELECT
ELECT
ELECT
0.1uF
47uF
1000uF
220uF
1000uF
50V
63V
16V
16V
16V
C205
C206
C207
1-126-925-11 ELECT
1-126-967-11 ELECT
1-126-925-11 ELECT
470uF
47uF
470uF
10V
50V
10V
8-719-904-05
8-719-904-05
8-719-904-05
8-719-904-05
8-719-030-24
DIODE
DIODE
DIODE
DIODE
DIODE
1N4005
1N4005
1N4005
1N4005
EG01C
D107
D108
D201
D202
D203
8-719-061-02
8-719-061-02
8-719-030-24
8-719-510-73
8-719-027-22
DIODE
DIODE
DIODE
DIODE
DIODE
PR1003
PR1003
EG01C
S3L20U
D3S6M
D205
D206
8-719-030-24 DIODE
8-719-061-02 DIODE
EG01C
PR1003
Remarks
1-779-725-11
1-500-144-11
A-6759-620-A
8-848-576-02
CONNECTOR, BOARD TO BOARD 5P
HEAD, FE
HEAD BLOCK ASSY, ACE (TDK)
DRUM ASSY, UPPER DZR-45-R
(EXCEPT 998HF)
8-848-594-02 DRUM ASSY, UPPER DZR-51-R (998HF)
770
776
8-848-666-11 DRUM ASSY, LOWER DZL-51B/J-RP
8-839-044-02 DRUM ASSY DZH-94A/Z-RP (M901)
(EXCEPT 998HF)
776
8-839-046-02 DRUM ASSY DZH-96A-R (M901)(998HF)
M902
1-698-971-11 MOTOR, DC
M903
X-3947-577-1 MOTOR ASSY, CAM
************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
1-475-554-41 COMMANDER, STANDARD (RMT-V232C)
(798HF)
1-475-605-11 COMMANDER, STANDARD (RMT-V229)
(998HF)
1-569-008-11 ADAPTOR, CONVERSION 2P
(998HF: Chilean, PX)
1-569-008-21 ADAPTOR, CONVERSION 2P
(998HF: Chilean, PX)
1-696-592-11 CORD, CONNECTION (NTSC) (FOR RF) 1.5m
< DIODE >
D101
D102
D103
D104
D105
POWER BLOCK SR709
1-776-258-11 CORD, AVC CONNECTION (FOR VIDEO/AUDIO)
1.5m
1-783-325-11 CORD, CONNECTION (CABLE MOUSE)
3-861-047-11 MANUAL, INSTRUCTION (ENGLISH)(798HF)
3-861-047-21 MANUAL, INSTRUCTION (FRENCH)
(798HF: Canadian)
3-861-048-11 MANUAL, INSTRUCTION (ENGLISH)
(998HF: US, Canadian, PX)
3-861-048-21 MANUAL, INSTRUCTION (FRENCH)
(998HF: Canadian)
3-861-048-31 MANUAL, INSTRUCTION (SPANISH)
(998HF: Chilean, Mexican)
3-979-315-01 COVER, JACK
3-979-316-12 INDIVIDUAL CARTON (798HF)
3-979-316-21 INDIVIDUAL CARTON
(998HF: US, Canadian, PX)
*
*
< FUSE >
! F101
1-532-388-31 FUSE
T2A
*
3-979-316-62 INDIVIDUAL CARTON(998HF: Chilean, Mexican)
*
3-979-317-01 CUSHION
*
3-979-512-01 SPACER
************************************************************
250V
< IC >
! IC201
8-759-420-19 IC AN1431T
**************
HARDWARE LIST
**************
< PHOTOCOUPLER >
! PC101
8-749-010-65 PHOTOCOUPLER PC123
< RESISTOR >
R201
1-260-336-51 CARBON
4.7
1/2W
R208
1-249-401-51 CARBON
47
5%
1/4W
R209
1-249-393-51 CARBON
10
5%
1/4W
************************************************************
7-15E
#1
#2
#702
#702
#703
7-685-648-79
7-685-646-79
7-685-646-79
7-682-547-04
7-685-133-19
SCREW +BVTP 3X12 TYPE2 IT-3
SCREW +BVTP 3X8 TYPE2 IT-3
SCREW +BVTP 3X8 TYPE2 IT-3
SCREW +P 3X6
SCREW (DIA. 2.6) (IT3B)
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
SLV-798HF/998HF
Sony Corporation
9-921-672-11
Home A&V Products Company
— 120 —
98C1637-1
Printed in Japan © 1998.3
Published by General Engineering Dept.
(Osaki East)