Download INSTALLATION MANuAL

6. ANTI HI-JACK MODE
There are three different ways to activate Anti Hi-Jack (AHJ).
1. By Ignition (Programmable Feature #7, Default setting is OFF)
When Programmable Feature #7 is ON, and the ignition is turned
on, the alarm will enter AHJ mode. The siren will chirp three times
and the LED will flash fast.
Note: If programmable feature #7 hi-jack through ignition is enabled
(ON) you must exit hi-jack mode using the valet button before
entering programming mode, see section 4 to enter programming
mode. Do not turn ignition off, leave ignition on, then press valet
button 5 times to enter programming mode.
2. By Door (Programmable Feature #8, Default setting is OFF)
When Programmable Feature #8 is ON, and when the Ignition is ON
AND the driver door is opened then closed, alarm will enter AHJ
mode. The siren will chirp three times and the LED will flash fast.
3. By Remote Control (Programmable Feature #9, Default setting is OFF)
When Programmable Feature #9 is ON and Ignition ON, Press and
hold PANIC and AUX together for 2 seconds – alarm will enter AHJ
mode. Siren will chirp three times and LED will flash fast.
NOTE: All three features can be set to ON.
ANTI HI-JACK MODE ACTIVATED STATUS
• From 0-60 sec LED will flash quickly.
• From 61-70 sec LED will flash quickly, siren chirps, and the
parking light will flash.
• From 71-80 sec LED will flash quickly, siren chirps, parking light
will flash, and ignition cut output constantly.
• After 81 sec LED will flash quickly, siren chirps, parking light will
flash and ignition cut output constantly.
EXIT ANTI HI-JACK MODE
• From 00-60 sec, Turn on the ignition, then press and hold UNLOCK
button for 2 sec. The system will be in disarm mode.
• After 60 sec, Turn on ignition, then press override switch for 1 sec.
The system will be in disarm mode.
REMOTE OPERATION
GUIDE
#6888 INSTALLATION
Manual
#6888
REMOTE
OPERATION
#6888
GUIDE
#6888 REMOTE OPERATION GUIDE
OPERATION GUIDE
#6888
REMOTE OPERATION GUIDE
#6888 REMOTE
LOCK BUTTON
LOCK BUTTON
LOCK BUTTON
• Press and release the LOCK button to ARM ALARM
and LOCK DOORS
• Press and release the LOCK button to ARM ALARM
•• and
Press
and
LOCKALARM
DOORS
LOCK
DOORSthe
Press
and release
release
the LOCK
LOCK button
button to
to ARM
•• and
Press
and
button
and to
press
it again
for
LOCK
DOORSLOCK
Press
and release
release
the LOCK
button
LOCK
DOORS
2 SECONDS to BYBASS
SHOCK
SENSOR
and
ARM
the LOCK
button
ARM
LOCK
DOORS
• Press and release LOCK
button
and to
press
it ALARM
again
for
ALARM
(Use
this to bypass shock sensor)
and
LOCK
DOORS
SECONDS
to BYBASS
SHOCK
SENSOR
ARM
•• 2
Press
and
LOCK
button
and
press
it and
again
for
Press
and release
release
the LOCK
button
to
ARM
ALARM
ALARM
(Use
this
tothe
bypass
shock
sensor)
• 2
Press
and
release
LOCK
button
to LOCKand
DOORS
SECONDS
to
BYBASS
SHOCK
SENSOR
ARM
and
LOCK
DOORS
(Use
this toLOCK
bypass
shock
sensor)
•• ALARM
Press
release
button
and
press
it again
for
Press and
and
release
the
LOCK
button
to
LOCK
DOORS
2Press
SECONDS
to BYBASS
SHOCK
SENSOR
ARM
and release
release
LOCK
button button
and
press
itand
again
for
•• Press
and
the
UNLOCK
to DISARM
ALARM
(UseUNLOCK
this
to bypass
shock sensor)
2 SECONDS
to BYBASS
SHOCK
SENSOR and ARM
ALARM
and
DOORS
• Press
and
release
the
UNLOCK
button
to
DISARM
ALARM (Use
this to
bypass shock
sensor)STOP
•• ALARM
Press
release
the
and
UNLOCK
DOORS button
Press and
and
release
the UNLOCK
UNLOCK
button to
to DISARM
ALARM TRIGGER
and
UNLOCK
DOORS button to STOP
• ALARM
Press and
release
the UNLOCK
•• ALARM
Press
and
release
the
UNLOCK
button
TRIGGER
Press and
release the UNLOCK button to
to UNLOCK
DISARM
STOP
DOOR TRIGGER
and
UNLOCK
DOORS
•• ALARM
Press
release
the
Press and
and
release
the UNLOCK
UNLOCK button
button to
to UNLOCK
DISARM
•• DOOR
Press
and
Hold
the
UNLOCK
button
for
2
SECONDS
Press
and
release
the UNLOCK
UNLOCK
ALARM
and
UNLOCK
DOORS button to STOP
to switchTRIGGER
ALARM to KEYLESS basic mode.
ALARM
DOOR
•• Press and Hold
thethe
UNLOCK
button
for to
2 SECONDS
release
UNLOCK
button
STOP
to
switch
ALARM
tothe
KEYLESS
basic
mode.
• Press
and
release
UNLOCK
button
to2 UNLOCK
Press
and
Hold the
UNLOCK
button
for
SECONDS
ALARM
TRIGGER
LOCK
to
switch
ALARM
KEYLESS
basic
mode.
• DOOR
Press
and
releasetothe
UNLOCK
button
to UNLOCK
LOCK
PRESS
•• Press
Press
andhold
Holdthe
thePANIC
UNLOCK
DOORand
TOGETHER •
LOCK
but- button for 2 SECONDS
switch
ALARM
to KEYLESS
basic mode.
• to
Press
and
Hold the
UNLOCK button
for 2 SECONDS
PRESS
LOCK BUTTON
LOCK BUTTON
UNLOCK BUTTON
UNLOCK BUTTON
UNLOCK BUTTON
UNLOCK BUTTON
UNLOCK BUTTON
PANIC BUTTON
PANIC BUTTON
BUTTON
tonPANIC
for 2 SECONDS
to TRIGGER
• Press
and ALARM
hold the to
PANIC
but- basic mode.
to switch
KEYLESS
HORN
/ SIREN
for and
2 SECONDS
to TRIGGER
• ton
Press
hold the
PANIC
butPANIC
BUTTON
HORN
ton
for 2/ SIREN
SECONDS to TRIGGER
PANIC
BUTTON
/ SIREN
• HORN
Press and
hold the PANIC butAUX
BUTTON
for 2and
SECONDS
to TRIGGER
•ton
Press
hold
the PANIC
butHORN
for /and
2SIREN
SECONDS
to TRIGGER
AUX
BUTTON
• ton
Press
release
the
AUX button for TRUNK
HORN
/ SIREN
AUX
BUTTON
RELEASE
TOGETHER
PRESS
LOCK
PANIC
TOGETHER
LOCK
PANIC
PRESS
TOGETHER
PANIC
PRESS
TOGETHER
PANIC
PANIC
Ignition must be OFF
Ignition must be OFF
During
IgnitionValet
must Mode
be OFF
Ignition
must Mode
be OFF
During Valet
Ignition
must Mode
be OFF
During Valet
Ignition
Ignition must
must be
be OFF
OFF
During Valet Mode
Ignition
must Mode
be OFF
During Valet
Ignition
must
OFF and
Alarm
must
bebe
ARMED
Ignition OFF
Alarm must be ARMED and
When
siren
/be
horn
is Sounding
Ignition
OFF
Alarm
must
ARMED
and
Ignition
OFF
When
siren
/ horn is Sounding
During
Driving
or
Valet
Mode
Alarm
must
ARMED
and
When siren
/be
horn
is Sounding
Ignition
OFF
During
Driving
Valet Mode
Alarm must
beor
ARMED
and
Alarm
must
be
DISARMED
When
siren
/ horn
is Sounding
During
Driving
or Valet
Mode
Ignition
OFF
and Ignition ON.
Alarm
DISARMED
When must
siren be
/ horn
is Sounding
and Ignition
During
Driving
or
Valet Mode
Alarm
must
beON.
DISARMED
and Ignition
During
DrivingON.
or Valet Mode
Alarm must be DISARMED
Press
LOCK and PANIC buttons
and Ignition
Alarm
must beON.
DISARMED
2nd AUXILIARY
2nd AUXILIARY
2nd
togetherAUXILIARY
to get AUX2 Output.
• Press
andON.
PANIC buttons
andLOCK
Ignition
Note: Contact installer to make sure this
together
to get
AUX2
Output.
• option
Press
LOCK
and
PANIC
buttons
2nd
AUXILIARY
is enabled.
Note:
Contactto
installer
to make Output.
sure this
together
get AUX2
2nd
AUXILIARY
option
is
enabled.
Contact
installer
make surebuttons
this
• Note:
Press
LOCK
andto PANIC
to getand
AUX2
Output.
• together
Press LOCK
PANIC
buttons
Note:
Contact to
installer
to make sure
this
together
get AUX2
Output.
option is enabled.
option is enabled.
Note: Contact installer to make sure this
• Press and release the AUX button for TRUNK
option is enabled.
•• Press
and
thethe
AUX
button
for for
2 SECONDS
Alarm must be DISARMED
RELEASE
Press
and hold
release
AUX
button
TRUNK for
SILENT
ARMING
and
Lock
Doors
and ignition OFF
RELEASE
• Press
and hold the AUX button for 2 SECONDS for
Alarm must be DISARMED
•• Press
and
hold
AUX
button
for
2
Alarm
must
ARMED
and
SILENT
ARMING
Lock
Doors
and ignition
Press
and
release
the
AUX
button
TRUNK for
hold the
theand
AUX
button
for for
2 SECONDS
SECONDS
for
Alarm
must be
beOFF
DISARMED
SILENT ARMING
DISARMING
and
Unlock
Doors
ignition
OFF
RELEASE
SILENT
Lock
Doors
and
ignition
•• Press
theand
AUX
button
for 2forSECONDS
Alarm
must beOFF
ARMED and
Press and
and hold
release
the
AUX
button
TRUNK for
SILENT
DISARMING
andbutton
Unlock
ignition
OFF
• Press
and
hold the AUX
forDoors
2 SECONDS for
Alarm
must
be ARMED
DISARMED
and
RELEASE
ARMING
and
Lock
Doors
and
ignition
DISARMING
and
Unlock
ignition
OFF
• SILENT
Press and
hold the
AUX
button
forDoors
2 SECONDS for
Alarm
must
beOFF
DISARMED
• Press
and
hold theand
AUX
button
for 2 SECONDS for
Alarm
beOFF
ARMED and
SILENT
ARMING
Lock
Doors
and must
ignition
USED FOR: 1. Stopping
horn/siren:
Turnthe
ignition
on,
pressfor
and
valet switch
stops.
DISARMING
and
Unlock
Doors
ignition
OFF
• SILENT
Press
and
hold
AUX
button
2 hold
SECONDS
for until horn/siren
Alarm
must
be ARMED and
2. To enter/exit
keyless
basic
mode
(LED
steady
on):
Ignition
on
and
hold
valet
switch
for
5
SILENT
DISARMING
and
Doors
ignitionstops.
OFF seconds.
USED FOR: 3.
1. Stopping
horn/siren:
Turn ignition
on,Unlock
press and
hold valet switch until horn/siren
Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on
To
enter/exit
keyless Turn
basicignition
mode (LED
steady
on):
Ignition
on anduntil
holdhorn/siren
valet switch
for 5 seconds.
USED FOR: 2.
1. each
Stopping
horn/siren:
on,
press
and
hold
valet
switch
stops.
remote to be programmed, turn ignition off. Up to 4 remotes may be programmed.
3.
Useenter/exit
to program
remotes:
ignition
press
and
release
switch
5 times,
buttons on
2. To
keyless
basicTurn
mode
(LED on,
steady
on):
Ignition
onvalet
and hold
valet
switchpress
for 5lock
seconds.
Most Common
Locations
(Ask
where
itignition
isturn
located.)
each
remote
to installer
be
programmed,
ignition
off. and
Up to
4 remotes
may
be 5programmed.
3.
Use
to
program
remotes:
Turn
on,
press
release
valet
switch
times,
press
USED
FOR:glove
1. Stopping
horn/siren:
Turn
ignition
on,behind
press the
and hold valet switch until horn/siren stops. lock buttons on
• Inside
compartment,
driver's
kick
panel,
each
remote
to
be
programmed,
turn
ignition
off.
Up
to
4
remotes
may
be
programmed.
Most
Common
Locations
(Ask
installer
where
it
is
located.)
2.
enter/exit
keyless
basic
mode (LED
steady
on):
Ignition
and until
hold horn/siren
valet switch
for 5 seconds.
USED
1.To
Stopping
horn/siren:
Turn ignition
on, press
and
hold
valet on
switch
stops.
fuseFOR:
panel
access
door,
underneath
• Inside
glove
driver's
kick
panel,
behind
the on):
3.
to front
program
remotes:
Turn
on,
press
andIgnition
releaseonvalet
5 times,
press
buttons on
Most
Locations
(Ask
installer
where
itignition
is(LED
located.)
2. Use
Tocompartment,
enter/exit
basic
mode
steady
and switch
hold valet
switch
for 5lock
seconds.
theCommon
dashboard
in
ofkeyless
the
driver.
panel
access
door, to
underneath
remote
be
programmed,
turnbehind
ignition
off. Up
4 remotes
be 5
programmed.
• fuse
Inside
glove
compartment,
driver's
kick
panel,
the
3. each
Use
to
program
remotes:
Turn
ignition
on, press
andtorelease
valetmay
switch
times, press lock buttons on
the
dashboard
in
front
of
the
driver.
fuse
panel access
door,
underneath
PARToff.
NUMBER:
each remote
to installer
beREPLACEMENT
programmed,
ignition
Up to 4#REMOTE-6888
remotes may be programmed.
Most
Common
Locations
(Ask
where it REMOTE
isturn
located.)
THIS
IS ONLY
dashboard
in front of the
driver.kick panel,
• the
Inside
glove compartment,
driver's
behind
the A GUIDE
AUX BUTTON
AUX BUTTON
VALET OVERRIDE SWITCH OPERATION
VALET OVERRIDE SWITCH OPERATION
VALET OVERRIDE SWITCH OPERATION
VALET OVERRIDE SWITCH OPERATION
VALET OVERRIDE SWITCH OPERATION
REPLACEMENT
PART NUMBER: #REMOTE-6888
Most Common
Locations (Ask installer
where itREMOTE
is located.)
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions.
panel
access
door, underneath
THIS
IS
ONLY
A• 6888-Op-oct2011.indd
GUIDE #REMOTE-6888
•fuse
Inside
glove
compartment,
driver's
kick
panel,
behind
the
REPLACEMENT
REMOTE
PART
NUMBER:
©2011
Micro
Alarm
Systems,
Inc.
the
in
front
of
theare
driver.
The button
operations
shown
a general guide. Consult
with
dealer that
installed your keyless entry to confirm these remote functions.
fusedashboard
panel
access
door,
underneath
THIS
IStheONLY
A GUIDE
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
the dashboard
in front shown
of thearedriver.
The button operations
a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions.
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
THIS IS ONLY A GUIDE
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions.
THIS IS ONLY A GUIDE
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions.
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
THIS IS ONLY A GUIDE
These instructions are a general guideline of possible applications. Specifications may change dependent
upon vehicle. Always review the vehicle’s service manual and wiring diagram when performing an
installation. Manufacturer does not assume any responsibility for damages to property or persons
which may occur due to incorrect applications or product failure. Not responsible for typographical
errors. Specifications are subject to change without notice.
8
Warranty void if not installed by authorized dealer.
Specification and date are subject to change or withdrawal without notice.
© 2011 Micro Alarm, Inc. • 6888-Inst-oct2011.indd
1. HOW TO “CODE LEARN” A REMOTE CONTROL:
5. 6888 ADDITIONAL INFORMATION
When Car Alarm is Disarmed and Ignition is off:
AUXILIARY ONE (Grey Wire) maybe used for either Trunk Release
(default) or Remote Starter. (Programmable feature #3)
1. Turn Ignition To ON Position.
2. Press Valet Override Switch 5 Times. Siren / Horn will Chirp Once
and Parking Light and LED will stay ON.
3. Press LOCK on each remote to be programmed. Siren / Horn
will chirp and parking light will flash to confirm remote has been
programmed.
4. Turn Ignition OFF.
Press and relase AUX button to release
trunk OR engage Remote Starter.
• If Gray Wire is used for Trunk Release:
the system will disarm and unlock
vehicle
• If Gray wire is connected to enable
Remote Starter, the system will bypass
sensor and ignition
• Programmable feature #3 must be
programmed to either Trunk Release
(default) or Remote Starter.
Note 1: After 10 seconds without any programming activity, or if the
ignition is turned OFF, the System will automatically exit Remote
Control Programming Mode.
Note 2: Up 4 Remote Controls can be programmed.
SECOND AUXILIARY or HORN OUTPUT (Brown/White Wire) has
four programmable options (programmable feature #4):
2. JUMPER PIN AND WIRING CONFIGURATION
JP1
JP2
JP3
JP4
#6888
REPLACEMENT REMOTE PART#:
REMOTE-6888
JP1 - OPEN = Last Door Arm/Auto Rearm = OFF
CLOSED = Last Door Arm/Auto Rearm = ON
JP2 - OPEN = Last Door Arm/Auto Rearm w/o Door Lock
CLOSED = Last Door Arm/Auto Rearm w/ Door Lock
JP3 - OPEN = Door Light Delay for 60 Sec = ON
CLOSED = Door Light Delay for 60 Sec = OFF
JP4 - OPEN = CDL Pulse Timer = 3.5 Sec
CLOSED = CDL Pulse Timer = 0.5 Sec
NOTE: DEFAULT FOR ALL JPS IS CLOSED
1. PULSE – Provides a negative output as long as “Lock” and “Panic”
are pressed and held together. (Default)
2. LATCH OUTPUT – Provides a negative output for 25 seconds
when “Lock” and “Panic” buttons are pressed together at the
same time and released.
3. HORN – Horn and siren work together only on all alarm events.
Siren will work on all events.
4. LIMITED HORN – Horn enables when alarm is triggered. Horn
does not activate when lock/unlock is pressed on the remote, only
the siren chirps.
6888 BRAINSTICKER
SHOCK SENSOR
(WHITE CONNECTOR)
DOOR LOCK
(RED CONNECTOR)
LED (WHITE CONNECTOR)
VALET SWITCH (BLUE CONNECTOR)
16 - N/A
15 - BLACK/WHITE WIRE (–) Dome Light Output
14 - N/A
13 - BROWN/WHITE WIRE (–) 2nd AUX / Horn
12 - BLUE WIRE (–) Hood Pin Input
11 - ORANGE WIRE (–) Starter Disable
10 - PURPLE WIRE (+) Door Trigger Input
9 - N/A
8 - GREEN WIRE (–) Door Trigger Input
7 - GREY WIRE (–) Trunk Release Output (Aux)
6 - YELLOW WIRE (+) Ignition Input
5 - BROWN WIRE (+) Siren Output (3 Amp)
4 - BLACK WIRE (–) Ground
3 - WHITE WIRE (+/–) Parking Light Output
2 - RED WIRE (+) 12 Volts
1 - RED/WHITE WIRE (+/–) Parking Light Input
2
5.3cm
16 15
14 13
12 11
10
9
8
7
6
5
4
3
2
1
6cm
NOTE: Programmable feature #4 must be programmed to how the
Brown/White wire is connected and intended to be used. ONLY
ONE OPTION MAY BE SELECTED AND PROGRAMMED.
AUXILIARY 2:
LOCK
IF LATCH IS WIRED /
CONFIGURED:
Press and Release
“Lock” and “Panic”
at same time to get a
negative output for 25
seconds
Press
TOGETHER
PANIC
7
IF PULSE IS WIRED /
CONFIGURED (Default):
A negative output will
be provided by pressing
and holding “Lock” and
“Panic” at the same time.
Output will be provided
as long as “Lock” and
“Panic” are held.
2A. JUMPER PIN INFORMATION
4.A PROGRAMMABLE FEATURE TABLE
FEATURES
LOCK:
Siren chirp
once
LED flash
once
1
Lock / Unlock
Pulse
Single*
Double
1 Short
Chirp
2
Disarm Parking
Light O/P
Flash
Twice*
Light
30 sec
1 Short
Chirp
3
Disarm
(1st AUX)
Trunk*
Car Start
(see Note 1)
1 Short
Chirp
4
2nd AUX / Horn
5
IGN Lock /
Unlock
On*
Off
1 Short
Chirp
6
Keyless Entry
Off*
On
1 Short
Chirp
7
IGN Anti
Hi-Jack
Off*
On
Note 6
1 Short
Chirp
8
Door
Anit Hi-Jack
Off*
On
1 Short
Chirp
9
Remote Anit
Hi-Jack
Off*
On
1 Short
Chirp
10
UNLOCK:
PANIC:
AUX:
Siren
Siren chirp Siren chirp Siren chirp
Chirp
twice
3 times
4 times
Indicator
LED flash LED flash 3 LED flash 4
twice
times
times
Pulse*
Latch
Horn
Limited Horn
(see Note 2) (see Note 3) (see Note 4) (see Note 5)
Back to
Press AUX for 3 seconds. Siren will chirp 6 times.
Factory Default Light will flash 6 times. All features will be returned
to default settings.
1 Short
Chirp
1 Short
Chirp
*All settings shaded in gray are factory default settings.
Note 1:CAR START – Press and release AUX button to get a 0.5 second negative output
on the 1st channel (trunk release wire). This will bypass the sensor and ignition.
Note 2:PULSE – Press and hold the LOCK and PANIC buttons, and the 2nd Channel
Output will send signal as long as the LOCK and PANIC buttons are held.
Note 3:LATCH – Press LOCK and PANIC buttons for a 30 second signal output.
Note 4:HORN – The Horn wire will have an output whenever the Siren wire has an output.
Note 5:Limited Horn – The Horn will sound only during Door Trigger, Ignition, or when
the Shock Sensor is triggered. The siren will sound/chirp on all events.
Note 6: If ignition hi-jack is enabled, you must disable hi-jack using the valet button before
entering programming mode. Leave ignition on after turning off hi-jack.
See ignition hi-jack on page 8.
4.B LED INDICATION TABLE
Type of Trigger in Armed Mode
LED Status
No Trigger
LED Flash rapidly (Auto Rearm Activated)
Ignition
1 Flash & 1 Pause
Pin Switch Zone
2 Flash & 1 Pause
Door Zone
3 Flash & 1 Pause
Sensor Zone
4 Flash & 1 Pause
6
Jumper 1
OPEN – Last Door Arm/Auto Rearm = OFF
CLOSE – Last Door Arm/Auto Rearm = ON
Jumper 2
OPEN – Last Door Arm/Auto Rearm without Door Lock
CLOSE – Last Door Arm/Auto Rearm with Door Lock
Jumper 3
OPEN – Dome Light Delay for 60sec = ON
CLOSE – Dome Light Delay for 60sec = OFF
Jumper 4
OPEN – Central Door Lock (CDL) Pulse Timer = 3.5sec
CLOSE – Central Door Lock (CDL) Pulse Timer = 0.5sec
Default setting for all jumpers is CLOSED.
2.B POWER HARNESS WIRING CONFIGURATION
Pin#1: RED/WHITE = PARKING LIGHT INPUT VOLTAGE (+/–)
• This Input will provide the Voltage and Polarity to White Wire,
fused at 10 Amps.
Pin#2: RED = MAIN POWER CONNECTION, 12V (+)
• Connect to the (+)12V Battery Terminal, Fused at 15 Amps.
Pin #3: WHITE = PARKING LIGHT OUTPUT (+/–)
• Connect this Wire to the Vehicle 12 Volts Parking Light Circuit.
• This Output will provide a Flashing 12 Volts fused at 10 Amps to
energize vehicle’s Parking Light.
Pin #4: BLACK = GROUND (–)
• Connect this wire to Chassis ground.
Pin #5: BROWN = SIREN OUTPUT (+)
• This wire will provide a (+)12Volts positive Output for
powering a Siren(3A).
Pin #6: YELLOW = IGNITION INPUT (+)
• Connect to the Vehicle (+)12 Volt Ignition Wire
Pin #7: GRAY = AUXILIARY/TRUNK RELEASE OUTPUT, 500mA (–)
• This wire will provide a 12V. Negative output.
• May be used for remote starter, see programmable feature #3.
3
2.B POWER HARNESS WIRING CONFIGURATION
CONTINUED
Pin #8: GREEN = Negative Trigger Door Input (–)
• This Input will trigger the Alarm if it becomes Grounded while
alarm is armed (if door is opened).
Pin #9: N/A
Pin #10: PURPLE = Positive Trigger Door Input (+)
• This Input will trigger the Alarm if it receive +12 Volts while alarm
is armed (if door is opened).
Pin #11: ORANGE = Starter Kill Output (–)
• This output needs to be used with a relay to be cut into the
vehicle starter wire.
Pin #12: BLUE = Hood Pin Input (–)
• This Input will trigger the Alarm if it becomes Grounded while
alarm is armed (if the hood is opened).
Pin #13: BROWN/WHITE = 2nd Auxiliary or horn honk output.
Note: Controlled through programmable feature #4.
Pin #14: N/A
Pin #15: BLACK/WHITE = Dome Light Supervision (–)
• This wire will provide a 0-60 sec for illuminated vehicle
when Alarm is Disarmed.
2.D 2 PIN HARNESS(LOCK/UNLOCK)
WIRING CONFIGURATION
GREEN:(-) Connect this Wire to Vehicle Lock Wire.
BLUE: (-) Connect this Wire to Vehicle Unlock Wire.
Note: For vacuum operated door lock system remove jumper pin #4.
Use Optional Part RRAL-DL to add door lock on-board relay interface.
3. VALET OVERRIDE SWITCH OPERATION
The Valet switch has five functions:
•To Program Remote Controls (see Section 1 – How to “Code
Learn” a Remote Control)
•To Program the “Programmable Features” (see Section 4 –
Programmable Features)
•Basic Keyless Entry Mode
• With Ignition ON, hold Valet switch for 5 seconds (repeat to exit).
• Only locks and unlocks doors; Horn and siren only work in
“Panic Mode”. LED steady on.
• NOTE: This is different from Programmable Feature #6, which
does Keyless Entry where all features work except door, hood,
and shock sensor triggers.
•To Stop Panic Mode if Remote is Lost or Not Present
• With Ignition ON, hold Valet switch until Horn/Siren stops.
Pin #16: N/A
• To Exit from Hi-jack mode
• Turn on ignition, then press override switch for 1 sec. The system will be in disarm mode.
2.C SHOCK SENSOR
4. PROGRAMMABLE FEATURES
Adjust Sensitivity for best protection.
To change any of the programmable features, please follow these steps.
1. If car receives light Impact, siren / horn will chirp 5 times in quick
succession and Parking Light will Flash once for warning purpose.
2. If car receives heavy impact, siren / horn will sound and Parking
Lights will Flash for 60 sec.
NOTE: Shock Sensor will sound maximum of 5 times, then will reset
to deactive until armed again.
4
1. Turn ignition ON.
2. Press Valet Override switch 5 times – the siren / horn will chirp
once and parking light and LED will stay on.
3. Press the Valet switch the number of times equal to the number of
the feature to be programmed
4. Press the button to be programmed (LOCK, UNLOCK, PANIC, AUX)
on the remote to choose the setting you desire.
5. Turn ignition OFF.
Note: If 10 seconds expire without any programming activity, the
parking light and LED will turn OFF, and the System will return to
Disarm mode.
5