Download XEA101 Service Manual - Great Lakes Business Equipment

SERVICE MANUAL
ELECTRONIC
CASH REGISTER
MODEL
XE-A101
SRV KEY : Not necessary
PRINTER : M-31
(U and A version)
CONTENTS
CHAPTER 1. SPECIFICATIONS ..................................................................... 1
CHAPTER 2. OPTIONS ................................................................................... 4
CHAPTER 3. MASTER RESET ....................................................................... 4
CHAPTER 4. HARDWARE DESCRIPTION..................................................... 5
CHAPTER 5. TEST FUNCTION....................................................................... 8
CHAPTER 6. SERVICE PRECAUTION ......................................................... 10
CHAPTER 7. CIRCUIT DIAGRAM AND PWB LAYOUT ................................ 11
PARTS GUIDE
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
>>>>> USE FONT <<<<<
Helvetica/ Helvetica-Condensed/ Century-Schoolbook/ Symbol & OriginalFonts: (RingWorld2/RingFont2/Pa
Symbol/PartsCod)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
CHAPTER 1. SPECIFICATIONS
2) KEY LIST
1. APPEARANCE
Keytop
Front view
Description
0-9,00
Display
Printer cover
Numeric keys
CL
Clear key
@/TM
Multiplication & Time display key
Keyboard
Paper feed key
Tax 1 Shift/RA
Tax 1 shift and Received on account key
Tax 2 Shift/PO
Tax 2 shift and Paid out key
%
Percent keys
ESC
Mode switch
Drawer
Drawer lock
2. RATING
Error escape key
VOID
Void key
CLK#
Clerk code Entry key
PLU
PLU code entry key
SHIFT
Department shift key
#/SBTL
Non-add code & Tax Included subtotal key
CHK
Check key
CH
Charge key
Weight
Approx 5.0kg
External dimension
(Including the drawer)
330 (W) x 363 (D) x 253 (H) mm
13 (W) x 14.3 (D) x 9.96 (H) inches
Power source
AC 120V ( 10%), 60Hz
Power consumption
Stand-by 4W
Operating 12.5W
4. MODE SWITCH
Working temperature
0~40°C (32 to 104°F)
1) LAYOUT
• Slid type
CA/AT/NS
Cash sale Amount tender and No Sale key
Dept1-8
Department key
VOID
3. KEYBOARD
OFF
REG
X/F
Z/PGM
1) KEYBOARD LAYOUT
Type
Normal keyboard
Key position
STD/MAX 30
Key pitch
19 (W) x 19 (H) mm
Key layout
Fixed type
5. DISPLAY
1) OPERATOR DISPLAY
SHIFT
TAX1
SHIFT
/RA
@/TM
TAX2
SHIFT
/PO
%
VOID ESC
PLU
7
3
8
4
CHK
#/
SBTL
CLK#
CH
6
2
CA/AT/NS
5
1
Display device:
LED numeric display
Number of line:
1 line
Number of positions:
8 positions numeric display
Color of display:
Yellow / Green
Character size:
Numeric 14 (H) x 8 (W) mm
(Layout)
Department code
PLU code
Repeat
2) DISPLAY CONTENTS
6. PRINTER
Departments/PLU Code:
The department code or PLU code entered appears on the left.
For example, if the key for department 1 is pressed, "1" would appear in the extreme left position.
Repeat:
Indicates the number of times the same department key is
pressed. If an entry is repeated more than ten times, only the first
digit is displayed (12 displays as "2").
(E) Error:
This symbol appears, accompanied by a warning beep, when an
error is made. If this occurs during a transaction because of an excessive digit entry, simply press CL and re-enter correctly.
(P) Program:
This symbol remains on the display when the cash register is being programmed in the Z/PGM mode.
(F) Finalization:
This symbol appears when a transaction is finalized by pressing
CA/AT/NS , CH or CHK .
(o) Subtotal:
This symbol appears when #/SBTL is pressed and the cash
register computes the subtotal, and also when the amount tendered is less than the total sale amount.
(C) Change:
This symbol appears whenever the change due amount is displayed.
(L) Low battery:
This symbol appears when the power of the installed batteries is
below a certain level or you need to replace the batteries with
new ones. (see the "Maintenance" section for explanation.)
(L) No battery:
This symbol appears when no batteries are installed. (see "Maintenance" and "Getting Started" sections for explanation.)
In addition, the following appear when appropriate:
• The minus sign (-) can appear in positions 2 to 8.
• The decimal point appears in positions 1 to 3.
• When entry of the secret code is necessary, "---"appears in positions 1 to 4.
1) PRINTER
• Model name:
M-31
• No. of stations:
1
• Printing system:
Print wheel selective type
• Printing capacity: max. 13 characters
• Character size:
1.6mm (W) x 2.8mm (H)
• Print pitch:
Column distance 2.1mm (numeric to numeric),
2.6mm (numeric to symbol)
Row distance 4.6mm
• Print speed:
Approximate 1.4 lines/s (6 digits/line)
• Paper feed speed: Approximate 4.3 lines/s
• Reliability:
MCBF 0.3 million lines
2) PAPER
• Paper roll dimension:
57.5 0.5mm
max. 80mm in diameter
• Paper quality:
Bond paper (paper thickness: 0.06 to
0.085mm paper weight: 47 to 64g/m2)
3) INKING
• Ink supply system: Ink rill
• From:
Roller
• Specification:
Material - rubber
• Ribbon life:
0.7 million characters
• Print color:
purple
4) LOGO STAMP (No)
5) CUTTER
• Manual cutter
6) PRINTING WHEEL LAYOUT
1
2
3
4
5
6
7
8
9 10 11 12 13
0
0
0
0
0
0
0
0
0
0
0
0
0
X
1
1
1
1
1
1
1
1
1
1
1
1
1
Z
2
2
2
2
2
2
2
2
2
2
2
2
2 RA
3
3
3
3
3
3
3
3
3
3
3
3
3 PO
4
4
4
4
4
4
4
4
4
4
4
4
4 VD
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6 @
7
7
7
7
7
7
7
7
7
7
7
7
7 ST
8
8
8
8
8
8
8
8
8
8
8
8
8 TX
9
9
9
9
9
9
9
9
9
9
9
9
9 CA
%
10
11
CH
12
13 #
CK
#
#
#
#
#
#
#
#
#
#
# CG
2) LOW BATTERY
7. DRAWER
Low battery indication will appear on the left side of display when the
battery voltage is low.
[OUTLINE]
Yes (1)
• Standard equipment:
• Max. number of drawers: 1
• The drawer consists of:
CASE 1: When sitting idle or after completion of transaction.
The machine can indicate the low battery condition (Always)
CASE 2: Low battery indication will not appear during key operations, but will appear after power up of the cash register.
(1) Drawer box (outer case) and drawer
(2) Money case
(3) Coin case
(4) Lock (attached to the drawer)
[Display sample]
" 0.00" : Battery is OK.
"L 0.00" : Low battery (You have to change the batteries.)
[SPECIFICATION]
After finalization
"F 12.34" : Battery is OK.
"L 12.34" : Low battery ("L" indicate instead of "F".)
1) DRAWER BOX AND DRAWER
Size
Material
Bell
Release lever
Drawer open sensor
330 (W) x 363 (D) x 98 (H) mm
13 (W) x 14.3 (D) x 3.9 (H) inches
Plastic
–
Standard equipment: situated at the bottom
–
2) MONEY CASE
Separation from the drawer
Separation of the bill compartments from the coin
compartments
Bill separator
Number of compartments
Disallowed
Allowed
–
4B/5C
Layout:
3) NO BATTERY
If the user forgets to replace the battery and the battery voltage falls
below a certain level, or if a power failure occurs with no batteries
installed, the memory contents cannot be retained. The CPU judges it
as no battery and performs the master reset. In this case, all the
settings and registrations are cleared. If, however, the power is continuously supplied to the AC cord, the memory contents are retained.
Low battery : Batteries are installed, but the voltage is low.
Memory back up can be done.
No battery
: Batteries are not installed or the voltage is extremely
low.
The master reset is executed when a power failure
occurs, when the batteries are not properly charged.
Low battery & No battery indication will appear at the most left position of display when the battery voltage is low.
CASE 1: When any numeric entry & item entry is not done or just
after finalization.
The machine can indicate the battery condition. (Always)
4B/5C
3) LOCK (LOCK KEY : LKGIM7331BHZZ)
• Location of the lock: Front
• Method of locking and unlocking:
• Key No:
To lock, insert the drawer lock key into the
lock and turn it 90 degrees counter clockwise.
To unlock, insert the drawer lock key and turn
it 90 degrees clockwise.
SK1-1
8. BATTERY
1) MEMORY BACK UP BATTERY
For memory back up, the dry battery ULM-3 (3 pieces) are needed.
1. Memory holding time:
Approx. 1 year after New dry batteries are installed.
2. Battery exchange method:
When the low battery symbol "L" lights up, replace the batteries (3
AA) replaced by the following method;
1) Power on the ECR.
2) Mode switch turn to "REG" mode.
3) Remove the OLD dry batteries (3 pieces).
4) Insert the NEW dry batteries (3 pieces).
5) Confirm the low battery symbol "L" is off.
CASE 2: When numeric entry or item entry is done.
Battery condition is not appeared.
Exceptionally, at the power is restored after power failure, the
low battery & No battery indication will appear on the display
only when the battery voltage is low.
And the indication will disappear after any key entry.
[Display sample]
" 0.00" : Battery is OK.
"L 0.00" : Low battery
"L 0.00" : No battery
After finalization
"F 12.34" : Battery is OK.
"L 12.34" : Low battery ("L" indicate instead of "F".)
"L 12.34" : No battery ("L" indicate instead of "F".)
L
L
CHAPTER 2. OPTIONS
1. OPTIONS (No)
2. SERVICE OPTIONS (No)
3. SUPPLIES
NO
NAME
PARTS CODE
PRICE RANK
1
ROLL PAPER
AS
2
INK ROLLER
AF
4 SPECIAL SERVICE TOOLS (No)
CHAPTER 3. MASTER RESET
Master reset: Clears all the memory and initializes each preset parameter.
The master reset should be performed by using the following procedure.
1. Turn off the power (Power OFF). (See Note 1.)
2. Let the ECR be without the memory back up battery.
3. Turn the mode switch to the others of Power-off position.
4. Turn on the power (Power ON). (See Note 2.)
When the master rest is completed, the buzzer sounds intermittently
three times.
5. Attach the memory back up battery to the ECR.
The master reset can also be accomplished in the following case.
(See Note 3.)
Note 1) Power OFF: Means disconnecting the AC power supply to
the machine.
(Specifically, unplugging the machine.)
Note 2) Power ON:
Means connecting the AC power to the machine.
(Specifically, plugging in the machine.)
Note 3) In case a power failure occurs when the machine has no
battery installed, the master reset operation is automatically
performed after the power has been restored.
DESCRIPTION
5 ROLLS/PACK
CHAPTER 4. HARDWARE DESCRIPTION
1. OUTLINE
2) KEYBOARD and MODE SW
• CPU:
MODE SW, KEY MATRIX is follows.
uPD780023A (ROM 24KB, RAM 1024B)
Note: Although the XE-A101 has 30 keys, the keyboard circuit is
actually 32 keys (+) the PF key.
• KEY BOARD: 30key including PF key
• MODE SW: 5position slide SW
POWER
OFF
DISPLAY: 7seg.+DP x 8digit LED (YELLOW GREEN) FRONT only
• DRAWER:
1ch, no open sensor
REG
• BUZZER:
1beep, piezo buzzer
• PRINTER:
M-31(no EURO SYMBOL)
1
VOID
X/F
Z/PGM
3
4
5
2
SLIDE SW
2. BLOCK DIAGRAM
AC
POWER
SUPPLY
6V
5V
MA IN
For Clock
4.19MHz
32.768kHz
FRONT display :8digit
ST1-
ST4-,ST5
22
26
1
2
3
4
5
6
31
7
8
9
10
11
12
13
14
15
16
17
18
19
21
24
25
27
28
30
32
8. 8. 8. 8. 8. 8. 8. 8.
Printer
M-31
CPU
A1
uPD 780023A
SW1
G1,DP1,A2 ~ G2,DP2
KST1
KST2
1
KST8
KE Y
KR1
KR6
BOARD
D RAWER
KR1
2
&
MODE SW
KST3
3
Battery
BU ZZER
5V
KST4
4
3. DISCRIPTION
KST5
5
MODE SW
1) DISPLAY
KR2 KR6 KR5 KR4 KR3
KCN2
6
7
13
25
1
1
2
8
14
2
11
12
19
9
3
17
18
3
23
4
28
24
20
10
5
30
26
21
4
6
ST3-
32
22
15
5
7
ST4-
29
31
27
16
8
ST4-
ST3-
(Output Timing of STROBE signal)
1ms
30~100us
ST2-
ST1-
ST1Display
strobe
ST2-
D13
1SS133 KST1
D14
1SS133 KST2
D15
1SS133 KST3
D16
1SS133 KST4
D17
1SS133 KST5
D18
1SS133 KST6
D19
1SS133 KST7
D20
1SS133 KST8
9
KEYBOARD
3) BUZZER
The BUZZER is driven by the P75/BUZ signal of the CPU.
Frequency : 4.095kHz
KST1
4) REWIND MOTOR
When the rewind motor is driven by the signal of the CPU.
PRINTER
MOTOR
REWIND
MOTOR
5ms 10ms
15ms
5) DRAWER
DRAWER OPEN signal :Output high signal between 50ms
6) DETECTING "LOW VOLTAGE"
• Values obtained by AD conversion and averaging
Register value: 138 ( 2.7V) or less
139 - 154 ( 2.7V - 3.0V)
more than 154
7) DESTINATION DETECTION port
U and A version
P66
L
No voltage
Low voltage
OK
4. CPU PORT TABLE
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
PIN Name
P50/A8
P51/A9
P52/A10
P53/A11
P54/A12
P55/A13
P56/A14
P57/A15
Vss0
Vdd0
P30
P31
P32
P33
P34/SI31
P35/SO31
P36/SCK31P20/SI30
P21/SO30
P22/SCK30P23/RXD0
P24/TXD0
P25/ASCK0
Vdd1
Avss
P17/ANI7
P16/ANI6
P15/ANI5
P14/ANI4
P13/ANI3
P12/ANI2
P11/ANI1
P10/ANI0
Avref
Avdd
RESETXT2
XT1
IC/VPP
X2
X1
Vss1
P00/INTP0
P01/INTP1
P02/INTP2
P03/INTP3/ADTRG
P70/TI00/TO0
P71/TI01
P72/TI50/TO50
P73/TI51/TO51
P74/PCL
P75/BUZ
P64/RDP65/WRP66/WAITP67/ASTB
P40/AD0
P41/AD1
P42/AD2
P43/AD3
P44/AD4
P45/AD5
P46/AD6
P47/AD7
Signal Name
RWND
DR
SA2
SB2
SC2
SD2
SE2
SF2
GND
VDD
ST1ST2ST3ST4ST5
NU
NU
SA1
SB1
SC1
SD1
SE1
SF1
VDD
GND
VBAT
NU
KR6
KR5
KR4
KR3
KR2
KR1
VCC
VDD
RESETXT2
XT1
GND
X2
X1
GND
/POF
T
t
R
SG1
SDP1
SG2
SDP2
NU
BUZ
MTR
TRG
MSL1
MSL2
KST1
KST2
KST3
KST4
KST5
KST6
KST7
KST8
Description
REWIND MOTOR
To DRAWER
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
Output/Input
O
O
O
O
O
O
O
O
Initial state
L
L
L
L
L
L
L
L
When STBY
O/L
O/L
O/L
O/L
O/L
O/L
O/L
O/L
DISPLAY STROBE N-Ch O.D.
DISPLAY STROBE N-Ch O.D.
DISPLAY STROBE N-Ch O.D.
DISPLAY STROBE N-Ch O.D.
DISPLAY STROBE (H ACTIVE)
(GND via 56k)
(GND via 56k)
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
O
O
O
O
O
I
I
O
O
O
O
O
O
H
H
H
H
L
I
I
I
I
O/L
I
I
O/L
O/L
O/L
O/L
O/L
O/L
BATTERY voltage
RESERVE FOR KEY RETURN
KEY RETURN
KEY RETURN
KEY RETURN
KEY RETURN
KEY RETURN
KEY RETURN
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
O
O
O
O
O
O
O
O
I
I
O
O
O
O
O
O
O
O
I
I
I
I
O/L
O/L
O/L
O/L
O/L
O/L
O/L
O/L
I
I
O/L
O/L
O/L
O/L
O/L
O/L
O/L
O/L
L
L
L
L
L
L
32.768Khz Xtal
32.768Khz Xtal
SYSTEM CLOCK
SYSTEM CLOCK
POWER OFF
From PRINTER
From PRINTER
From PRINTER
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
DISPLAY SEGMENT
BUZZER
To PRINTER
To PRINTER
MODEL SELECT1
MODEL SELECT2
KEY STROBE
KEY STROBE
KEY STROBE
KEY STROBE
KEY STROBE
KEY STROBE
KEY STROBE
KEY STROBE
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
CHAPTER 5.TEST FUNCTION
1) To execute the diag test, set the mode switch to Z/PGM. Enter the
desired JOB code, and press the PO (paid out) key.
2. KEY TEST
2) The test message is printed by the printer.
1) KEY OPERATION
3) Test contents and key operations.
NO.
Test contents
1
Mode switch test
2
Key test
3
Display buzzer test
4
Key operations
02
PO
1
PO
02
PO
2) TEST PROCEDURE
3
PO
Perform the keyboard check with the sum check data of the key code.
Drawer test
4
PO
5
Printer test
5
PO
6
CPU version NO. print
6
PO
Enter the sum check data of each model in the four digits preceding
the diag number 02, and compare the data with the key position code
which is added until the CA/AT/NS key is pressed.
7
Battery level test
7
PO
8
Time display test
8
PO
9
Destination display
9
PO
1. MODE SWITCH TEST
If the data coincides with the code, the completion print is performed.
If not, the error print is performed.
Completion print
Error print
–––
02
02
XXXX
Sum data
3. DISPLAY BUZZER TEST
1) KEY OPERATION
1) KEY OPERATION
1
PO
3
PO
2) TEST PROCEDURE
Change over the mode switch as follows. If the mode switch data in
the proper sequence is not read with the above operation, an error is
printed.
To cancel this test mode, set the mode switch to any a position other
than Z/PGM to Z/PGM. In this case, the completion print is performed.
During the test , the display indicates hard codes which correspond to
the switch positions.
Display:
Z/PGM
X/FLASH
VOID
(04)
(03)
(02)
Completion print
Error print
–––
Check the continuous buzzer sound and the display state.
Display state:
8. 7. 6. 5. 4. 3. 2. 1.
The decimal point will shift from the lower digit to the upper, step by
step (500mSEC). To cancel the test mode, press any key, and the
buzzer will stop and the completion print is performed.
Completion print
3) MODE SWITCH OPERATION
Mode:
2) TEST PROCEDURE
OFF
REG
(01)
01
01
03
4. DRAWER TEST
1) KEY OPERATION
4
PO
2) TEST PROCEDURE
The drawer opens with the above key operation. Check that the
drawer is open. Press any key to terminate the test.
Completion print
04
5. PRINTER TEST
8. TIME DISPLAY TEST
1) KEY OPERATION
1) KEY OPERATION
5
PO
2) TEST PROCEDURE
8
PO
2) TEST PROCEDURE
With the above key operation , the print test pattern is repeatedly
printed.
Pressing any key will terminate the test after the completion of one
cycle print. (The receipt is issued at the end.)
8
6
7
5
4
3
2
1
Display
Hour
Second
Minute
Turn on and off(0.5s)
To terminate the test and print the date and time, press any key.
Print
X X X X X X
Year Month Date
X X X X X X
Hour Minute Second
0 8
9. DESTINATION DISPLAY
1) KEY OPERATION
9
PO
2) TEST PROCEDURE
6. CPU VERSION NO. PRINT
Display the destination code as follows.
1) KEY OPERATION
U and A version
V version
Japan
0
1
2
Display
6
PO
Display
2) DESCRIPTION
The CPU version No. are printed with above key operation.
(Print example)
0101
CPU version NO.
06
This test is terminated when printing is completed.
7. BATTERY VOLTAGE SENSOR TEST
1) KEY OPERATION
7
PO
2) TEST PROCEDURE
Displays A/D conversion port read value.
0155 or greater: Normal
0154 or smaller: Low battery display
0138 or smaller: No battery display and MSR is done when power on.
To terminate the test, press any key.
Completion print
07
X (X:0)
To terminate the test, press any key.
Completion print
09
CHAPTER 6. SERVICE PRECAUTION
1. PRINTER
Since there are no service parts for this model printer, only the printer
unit is supplied. Therefore, the printer component parts are not supplied and no service document is issued.
For troubleshooting of the printer, refer to the table below:
Printer life: 300 thousand lines (XE-A101: M-31)
Ink roll life: 1 million characters
Phenomena
Check point/possible cause
• The printer motor is locked and the • Check if the printer cable is disconnected.
Repair
• Check and repair the printer cable.
buzzer sounds intermittently.
• The printer does not work properly
• Check if the printer life is reached.
• Replace the printer.
• Check if any foreign material is attached to the • Remove the foreign material. (After removing
printing type wheel or the gear section.
• Defective print (Lack on the upper/ • Check if the printing type is worn down.
lower or left/right side)
• Uneven pitch of print paper feed
• Replace the printer.
• Check if any foreign material is attached to the • Remove the foreign material. (After removing
printing type wheel.
• Thin print
the foreign material, set the mode switch to
"REG" and press "CL" key.)
the foreign material, set the mode switch to
"REG" and press "CL" key.)
• Check if the ink roll life is reached.
• Replace the ink roll.
• Check if the ink roll is properly installed.
• Install the ink roll properly.
• Check if the printing type wheel is worn down.
• Replace the printer.
• Check if the roll paper size is proper.
• Use roll paper as specified below;
Paper width:
Outside diameter:
Inside diameter of paper tube:
Paper thickness:
• Check if a load is applied to the roll paper during • Remove any foreign material.
paper feeding. This may result from a foreign
materials attached to the roll paper.
57.5 0.5mm
ϕ80mm or less
ϕ12mm or less
0.06~0.085mm
A
B
C
D
7
6
5
8
D11
SO30
1N4002
HOLE only
PRINTER I/F PWB
52011-0810
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
VDD
VDD
CON3A
VSS
SI30
CN5
(for PRINTER)
KR1-KR6
56K
R14
R13
56K
R12
56K
5267-02
MOTOR CN
Q2
2SD2170
1
2
CN4
DR
MAIN PWB
+6V
KR6
KR5
KR4
KR3
KR2
VBAT
SA1
SB1
SC1
SD1
SE1
SF1
/ST1
/ST2
/ST3
/ST4
ST5
SA2
SB2
SC2
SD2
SE2
SF2
RWND
VDD
HOLE only
1
2
3
4
5
6
7
8
CON3
R8
1K
(F3:JUMPER)
/SCK30
VDD
F3
T1.0AL/250V
5273-02A
1
2
CN1
1) MAIN CIRCUIT
VCC
VDD
1K
R30
R28
TRG
MTR
47K*6
R15
R16
R17
R18
R19
R20
7
1K
R29
1K
LB1268(DIP)
1 NC
2 I1
3 I2
4 GND
IC3
uPD780023A (QFP)
NC 8
O1 7
O2 6
VCC 5
D12
1SS133
22uF
50V
C9
D4
D3
1N4002x4
D2
D1
1 P50/A8
2 P51/A9
3 P52/A10
4 P53/A11
5 P54/A12
6 P55/A13
7 P56/A14
8 P57/A15
9 VSS0
10 VDD0
11 P30
12 P31
13 P32
14 P33
15 P34/SI31
16 P35/SO31
17 P36/-SCK31
18 P20/SI30
19 P21/SO30
20 P22/-SCK30
21 P23/RXD0
22 P24/TXD0
23 P25/ASCK0
24 VDD1
25 AVSS
26 P17/AN17
27 P16/AN16
28 P15/AN15
29 P14/AN14
30 P13/AN13
31 P12/AN12
32 P11/AN11
IC2
VO
C1
MYLOR
0.033uF
F1
T1.25AL/125V
T1.0AL/250V
1. CIRCUIT DIAGRAM
R10
2.7K
1K
R11
VPP
+6V
C14
0.1uF
KR1
Q3
C3198
C10
MYLOR
0.1uF
6
C15
0.1uF
R31
10K
VCC
SP1
SHORTPIN
/RESET
47K
R23
t
T
R
R33
10K
VDD
VCC
R21
R24
47K
NOT USE
KST1-KST8
R22
J6
7mm
/RESET
C16
0.1uF
R32
10K
P74
SDP2
SG2
SDP1
SG1
R
t
T
/POF
TRG
MTR
KST8
KST7
KST6
KST5
KST4
KST3
KST2
KST1
C11
MULTI
0.1uF
/RESET
1 2 3
IC1
KIA7806P
C3
330uF
25V
STROBE [/ST1-/ST4,ST5]
P47/AD7 64
P46/AD6 63
P45/AD5 62
P44/AD4 61
P43/AD3 60
P42/AD2 59
P41/AD1 58
P40/AD0 57
P67/ASTB 56
P66/-WAIT 55
P65/-WR 54
P64/-RD 53
P75/BUZ 52
P74/PCL 51
P73/TI51/TO51 50
P72/TI50/TO50 49
P71/TI01 48
P70/TI00/TO0 47
P03/INTP3/ADTRG 46
P02/INTP2 45
P01/INTP1 44
P00/INTP0 43
VSS1 42
X1 41
X2 40
IC 39
XT1 38
XT2 37
-RESET 36
AVDD 35
AVREF 34
P10/AN10 33
4.7K
R9
1N4002
1N4002
C2
3300uF
25V
D6
D5
VO
R26
330K
(0)
SA2
SB2
SC2
SD2
SE2
SF2
SG2
DP2
SA1
SB1
SC1
SD1
SE1
SF1
SG1
DP1
C12
22pF
(18pF)
47K
47K
VCC
C4
100uF
25V
D8
D7
1
2
CN2
8
6
4
2
8
7
5
3
1
7
5
3
1
IC5G
IC4A
5
9PIN :GND
10PIN:N.C
IC5
KID65083
IC5H
11
13
15
17
11
13
15
4
6
17
12
14
16
18
12
14
16
2
1M
R27
3
18
BUZZER
C13
30pF
(22pF)
2
IC4B
9PIN :GND
10PIN:N.C
IC4
KID65083
R70
100
BZ
X1
32.768KHz
470
R25
5267-02BL
BATTERY CN
1SS133
1SS133
VCC
+6V
1
R2
1M
D9
a2
b2
c2
d2
e2
f2
g2
dp2
a1
b1
c1
d1
e1
f1
g1
dp1
X2
4.19MHz
XE-A101
R34
R35
R36
R37
R38
R39
R40
R41
R42
R43
R44
R45
R46
R47
R48
R49
R50
110
110
110
110
110
110
110
110
110
110
110
110
110
110
110
110
4.7K
X
O
4
R51
12K
330
Q4
2SC3198
R53
6.8K
3 8
Q5
KTA1271
(G3)
R54
330
VDD
VCC
R55
6.8K
3
1
3
Q6
KTA1271
3
4 1 1 1 2 3 1 1 9 7 1 5 6 8 1 1
7 8
5 6
2
0 1
1
4
LED4
D568GWA
C26
47uF/16V
5 1 9 1 2 4 6 7
0
LED5
S568GWA
C6
47uF/16V
VBAT
R52
(XE-A101V only)
R21
68K
R3
R24
4
1SS133
*CAUTION*
C5
MYLOR
0.1uF
220
R1
CHAPTER 7. CIRCUIT DIAGRAM AND PWB LAYOUT
8
R57
6.8K
R6
C7
MULTI
0.1uF
100K
R5
56K
1
3
Q7
KTA1271
VCC
4 1 1 1 2 3 1 1 9 7 1 5 6 8 1 1
7 8
5 6
2
0 1
1
4
D10
1SS133
R4
5.6K
R56
330
VO
LED3
D568GWA
ZD1
MTZ7.5B
/POF
R59
6.8K
1
3
2
R60
330
R61
6.8K
D30
JUMPER WIRE
(1N4002)
1
3
Q9
KTA1271
+6V
Q1
2SD2170
1
2
3
(for DRAWER)
1/2
CN3
5045-03A
1
1
4 1 1 1 2 3 1 1 9 7 1 5 6 8 1 1
7 8
5 6
2
0 1
1
4
LED1
D568GWA
1K
R7
C8
MULTI
0.1uF
Q8
KTA1271
DR
F2
T400mA/250V
4 1 1 1 2 3 1 1 9 7 1 5 6 8 1 1
7 8
5 6
2
0 1
1
4
VO
R58
330
LED2
D568GWA
2
A
B
C
D
A
B
C
D
22
31
29
8
KEYBOARD
26
32
18
17
30
12
11
24
2
1
28
7
6
27
15
21
20
3
19
8
13
16
5
4
10
23
9
14
25
KCN2
52045-0945
(5597-09CPB)
9
8
7
6
5
4
3
2
1
5
Z/PGM(4)
1SS133
1SS133
D19
D20
7
1SS133
1SS133
D16
D18
1SS133
D15
1SS133
1SS133
D14
D17
1SS133
D13
MODE SW
4
X/FLASH(3)
2
SLIDE SW PWB
5229-05APB
5
4
3
1
2
KCN3
1
SW1
3
7
VOID(2)
REG(1)
2) KEY INTERFACE
8
6
10
9
8
7
6
5
4
3
2
1
KCN1
MAIN PWB
52045-1045
(MAIN PWB)
KST1
KST8
KST7
KST6
KST5
KST4
KST3
KST2
KST1
KST5
KST4
KST3
KST2
KR1
6
KST4
KST5
JUMPER WIRE
JP4
JUMPER WIRE
JP5
KST1-KST8
5
KST3
JUMPER WIRE
JP3
JUMPER WIRE
KST2
KR1
JUMPER WIRE
JP2
JP1
KR3
KR4
KR5
KR6
KR2
5
KR1-KR6
3300pF
C25
3300pF
C24
3300pF
C23
330OpF
C22
330OpF
C29
100pF
C21
100pF
C20
100pF
C19
100pF
C18
100pF
C17
4
24
15
31
4
25
16
7
22
17
8
26
REG(1)
3
27
18
9
1
3
2
28
19
10
POWER
OFF
3
29
20
11
SLIDE SW
XE-A101
VOID(2)
2
30
21
12
4
X/F(3)
2
Z/PGM(4)
13
5
32
23
14
6
1
1
2/2
A
B
C
D
1) A side
2. PWB LAYOUTUT
1) B side
XE-A101U/A
PARTS GUIDE
MODEL
XE-A101
PRINTER:M-31
(for U.S.A,Canada)
CONTENTS
1
2
3
4
5
6
■
Exteriors
Drawer box unit(SK1-1 type)
Packing material & Accessories
Main PWB unit
Slide SW I/F PWB unit
Articles for consumption
Index
Parts marked with "!" are important for maintaining the safety of the set.Be sure replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be
used for after sales service only.
The contents are subject to change without
notice.
XE-A101U/A
1 Exteriors
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
32
33
34
35
36
37
38
40
PARTS CODE
GCOVB2523BHZZ
PCUT-6652BHZZ
XJBSD20P04000
GCABB2567BHZZ
XJPSD30P10X00
PGIDH2403BHZZ
PFILW2010BHZZ
HDECP2370BHZZ
GFTAB2445BHZZ
QTANZ2351BHZZ
QTANZ2349BHZZ
QTANZ2350BHZZ
QTANZ2348BHZZ
KI-OB6774BHZZ
XEBSD30P08000
GCOVB2524BHZZ
XBPSD26P04000
LHLDZ2388BHZZ
PGUMM2446BHZZ
RMOTM2321BHZZ
QCNW-3153BHZZ
CPWBF2915BH01
JKNBZ2428BHZZ
XBBSD30P06000
KI-OK2369BHZZ
CPWBF2916BH01
LANGK2904BHZZ
LFRM-2365BHZZ
PGUMM2445BHZZ
CSHEP2942BHZZ
LPLTM2365BHZZ
XJPSD30P06000
CKNBZ2427BHZZ
QCNW-3154BHZZ
QCNCW6882BH0H
PRICE NEW
RANK MARK
AS
N
AF
AA
BD
N
AC
AG
N
AP
N
AM
N
AG
N
AE
N
AG
N
AG
N
AF
N
BE
AA
AS
N
AA
AE
N
AC
N
AS
N
AF
N
BP
N
AE
N
AA
BF
N
AV
N
AH
N
AW
N
AY
N
AZ
N
AV
N
AA
BD
N
AF
N
AF
PART
RANK
D
C
C
D
C
C
D
D
D
C
C
C
C
E
C
D
C
C
C
B
C
E
C
C
E
E
C
D
C
B
C
C
C
C
C
DESCRIPTION
PRINTER COVER (GRAY-559)
Paper cutter
Screw (2×4)
TOP CABINET (GRAY(PB-N8.0))
Screw (3×10X)
PAPER GUIDE (GRAY(PB-N8.0))
FRONT FILTER
DECO PANEL (GRAY(PB-N8.0))
BATTERY COVER (GRAY(PB-N8.0))
BATTERY TERMINAL d
BATTERY TERMINAL A
BATTERY TERMINAL B
BATTERY TERMINAL c
Printer (M-31)
Screw (3×8)
DISPLAY COVER (GRAY-559)
Screw (2.6×4)
MOTOR HOLDER (GRAY(PB-N8.0))
MOTOR GUM
MOTOR
MOTOR CABLE
MAIN PWB UNIT
SLIDE S/W KNOB (GRAY(PB-N8.0))
Screw (3×6)
KEY BOARD
SLIDE SW I/F PWB UNIT
HEAT SINK
KEY FRAME
KEY RUBBER
KEY SHEET UNIT
BASE PLATE
Screw (3×6)
KEY TOP UNIT (KEY FRAME+KEY TOP)
BATTERY CABLE
Connector (52011-0810)
–1–
[PAPER CUTTER]
[SET]
[MOTOR]
[HEAT SINK]
[KEY BOARD]
(for Printer)
XE-A101U/A
1 Exteriors
16
7
6
8
9
1
24
5
4
2
10 11
12
13
3
26
17
19
38
22
20
37
25
18
15
15
14
32
15
21
28
36
36
25
36
33
27
15
34
40
35
15
36
RCP00399
36
15
15
15
15
–2–
XE-A101U/A
2 Drawer box unit(SK1-1 type)
NO.
!
!
PARTS CODE
XJPSD30P10X00
RTRNP2426BHZZ
QACCD1010CCN1
QCNW-3152BHZZ
GCOVH2525BHZZ
LPLTM2366BHZZ
GCABM2568BHZZ
PSHEP6826BHZZ
RPLU-6644BHZA
LX-BZ6775BHZZ
MLEVF2338BHZZ
MSPRT6742BHZZ
XBPSD40P06K00
NROLP6657BHZZ
MSPRC6743BHZZ
LBRC-2002BHZZ
MLEVF6699BHSA
MSPRT6731BHZZ
XNESD60-50000
NROLP6655BHZA
GCAS-2333BHZZ
LKGIW7330BHZZ
LKGIM7331BHZZ
PRNGT6637BHZZ
MSPRK6718BHZZ
MCAMM6633BHZA
XRESJ50-06000
DUNT-1306BHZA
XEBSD30P08000
LPLTM2367BHZZ
LPLTM2372BHZZ
LANGK2905BHZZ
MSPRC6748BHZZ
NSFTA6655BHZZ
GCAS-2335BHZZ
CCAS-2333BHZZ
CLOK-6673BHZZ
(Unit)
901 G B O X D 7 1 5 7 B H Z Z
1
2
3
5
7
8
13
14
15
16
17
18
19
20
21
22
23
24
25
26
28
29
30
31
32
33
34
35
36
37
38
40
41
44
45
501
502
PRICE NEW
RANK MARK
AC
AX
N
AP
AH
N
AG
N
AM
N
BE
N
AE
AX
N
AA
AF
N
AD
AA
AN
AG
AN
N
AF
N
AD
AA
AF
BA
N
AY
AE
AA
AF
AE
AA
AX
AA
AW
N
AQ
N
AN
N
AD
AE
AU
N
BF
N
BA
N
BT
N
PART
RANK
C
B
B
C
D
C
D
C
B
C
C
C
C
C
C
C
C
C
C
C
D
B
B
C
C
C
C
E
C
C
C
C
C
C
D
E
E
E
DESCRIPTION
Screw (3×10X)
POWER TRANS (U)
AC cord
PS CABLE
TRANS COVER (GRAY(PB-N8.0))
EARTH PLATE
DRAWER CABINET (PB-N8.0)
Gum sheet
SOLENOID
Screw (3×5)
LOCK LEVER
Open spring
Screw (4×6K)
Roller
Push out spring
BRACKET (4B)
BILL LEVER
Bill spring
Nut (M6)
Roller
MONEY CASE (4B GRAY)
Lock key (body)
Lock key (1pc)
Key ring
Lock key spring
Lock cam
E type ring (5mm)
Lock key unit
Screw (3×8)
BOTTOM PLATE
BALANCE PLATE
LOCK ANGLE
Plunger spring
Roller shaft
COIN CASE (5C GRAY)
MONEY CASE UNIT (4B/5C GRAY)
LOCK UNIT
DRAWER BOX (4B/5C GRAY)
–3–
[TRANS]
[except No.1∼8]
XE-A101U/A
2 Drawer box unit(SK1-1 type)
3
1
2
5
7
8
501
38
13
22
23
36
14
502
16
24
45
20
21
17
26
25
14
44
14
40
19
28
25
26
18
41
37
44
29 31
30
15
34
33
32
35
RCP00400
36
–4–
XE-A101U/A
3 Packing material & Accessories
NO.
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
20
PRICE NEW
RANK MARK
BC
N
BC
N
AX
N
AN
AF
N
AX
N
AA
AA
AR
N
AR
N
AR
N
AR
N
AD
AA
AE
AG
N
AG
N
AL
N
AL
N
AE
AQ
N
AQ
N
AQ
N
AC
PARTS CODE
SPAKC3176BHZZ
SPAKC3176BHSA
SPAKA3175BHZL
UREL-6629BHZZ
PSHEP6828BHZZ
SPAKA3175BHZR
SSAKH4231CCZZ
SSAKH3015CCZZ
TINSE2457BHZZ
TINSS2458BHZZ
TINSE2464BHZZ
TINSF2465BHZZ
TCAUZ6681BHZZ
SSAKH3012CCZZ
LKGIM7331BHZZ
TLABR2549BHZZ
TLABR2550BHZZ
TLABZ2548BHZZ
TLABZ2548BHSA
TGANE6644BHSC
TCADH2395BHZZ
TCADH2402BHZZ
TCADH2403BHZZ
SPAKA8339BHZZ
PART
RANK
D
D
D
C
D
D
D
D
D
D
D
D
D
D
B
D
D
D
D
D
D
D
D
D
DESCRIPTION
PACKING CASE
PACKING CASE
PACKING ADD L
Spool
Packing sheet
PACKING ADD R
Vinyl bag (140×500mm)
Vinyl bag (200×300mm)
INST BOOK
INST BOOK (S)
INST BOOK (E)
INST BOOK (F)
Battery caution label
Vinyl bag (80×120mm)
Lock key (1pc)
BAR CODE LABEL
BAR CODE LABEL
POP LABEL
POP LABEL
WARRANT CARD
SET UP GUIDE
SET UP GUIDE(E)
SET UP GUIDE(F)
Paper pad
(U.S.A)
(CANADA)
(U.S.A)
(U.S.A)
(CANADA)
(CANADA)
(U.S.A)
(CANADA)
(U.S.A)
(CANADA)
(CANADA)
(U.S.A)
(CANADA)
(CANADA)
3 Packing material & Accessories
4
7
10
6
9
16
15
11
3
20
8
5
14
2
13
1
RCP00401
4 Main PWB unit
NO.
!
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PARTS CODE
LANGK2904BHZZ
QCNCM1060AC03
QCNCM1101BHZZ
QCNCM6865BH0B
QCNCM7057BHZZ
QCNCW1057ACZZ
QCNCW2908BHZZ
QCNCW2943BHZZ
QCNCW2942BHZZ
QCNCW6882BH0H
QCNCW7081BHZZ
QCNW-3155BHZZ
QCNW-3181BHZZ
QFS-H0002QCZZ
QFSHD2109AFZZ
PRICE NEW
RANK MARK
AH
N
AB
AC
AB
AB
AB
AG
N
AF
N
AF
N
AF
AB
AH
N
AF
N
AF
N
AC
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
A
C
DESCRIPTION
HEAT SINK
Connector (Short Pin 3P)
Connector (5273-2)(2P)
Connector (5267-02A)
Connector (5045-3)(3pin)
Connector (Short socket)
CONNECTOR (5229-05APB)
K/B CONNECTOR (5597-09CPB)
K/B CONNECTOR (52045-1045)
Connector (52011-0810)
Connector (2P)(5267-02A)(Blue)
PRINTER I/F CABLE (8P)
GND WIRE (G6-G8-G10-G12)
FUSE (51S 1.25AL/125V)
Fuse holder (HD2109AF)
–5–
[IC1]
[SP1]
[CN1]
[CN4]
[CN3]
[SP1]
[KCN3]
[KCN1]
[KCN2]
[CN5]
[CN2]
[CON3-CON3A]
[G6-G8-G10-G12]
[F1]
[F1]
XE-A101U/A
4 Main PWB unit
NO.
!
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
901
PARTS CODE
QFS-K2005BHZZ
QSW-S2411BHZZ
RALMB5006SCZZ
RC-EZ0011QCZZ
RC-KZ1054CCZZ
RCRMZ6007RCZZ
RCRSP6676RCZZ
RH-IX2004BHZZ
VCCCPU1HH101J
VCCCTV1HH180J
VCCCTV1HH220J
VCEAGA1CW476M
VCEAGA1CW476M
VCEAGA1EW107M
VCEAGA1HW226M
VCEAGA1EW337M
VCKYPU1HB332K
VCKYPU1HB332K
VCKYTV1HF104Z
VCQYNA1HM333K
VCQYNU1HM104K
VHD1N4002G/-1
VHDDSS133HV-1
VHDDSS133HV-1
VHDDSS133HV-1
VHEMTZJ7R5B-1
VHIKID65083AP
VHILB1268//-1
VHIMC7806CT-1
VHPD5680GL2-1
VRD-RC2EY101J
VRD-RC2EY102J
VRD-RC2EY103J
VRD-RC2EY105J
VRD-RC2EY221J
VRD-RC2EY272J
VRD-RC2EY331J
VRD-RC2EY471J
VRD-RC2EY473J
VRD-RC2EY473J
VRD-RC2EY562J
VRD-RC2EY563J
VRD-RC2EY682J
VRD-RC2EY683J
VRS-CY1JD000J
VRS-CY1JD102J
VRS-CY1JD104J
VRS-CY1JD472J
VRS-CY1JD563J
VRS-CY2AY111J
VRS-CY2AY111J
VRS-CY2AY111J
VRS-CY2AY111J
VS2SC3198-/-1
VS2SD2170//-1
VSKTA1271//-1
XBBSD30P06000
(Unit)
CPWBF2915BH01
PRICE NEW
RANK MARK
AF
AK
N
AD
AH
N
AB
AD
AG
BA
N
AB
AA
AA
AB
AB
AB
AB
AC
AA
AA
AA
AA
AB
AA
AA
AA
AA
AC
N
AM
AK
AG
N
AQ
N
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
AA
N
AA
N
AA
N
AL
AH
AE
AA
BP
N
PART
RANK
A
B
B
C
C
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
C
E
DESCRIPTION
FUSE (LT-5 T400mAL/250V)
SLIDE SWITCH (JSS2601CS)
Buzzer (EFB-RD22C01)
CAPACITOR (3300µF/25V)
Capacitor (50WV 0.1µF)
Resonator (4.19MHz)
X-TAL (32.768KHz)
CPU (uPD780023A)
Capacitor (50WV 100pF)
Capacitor (50WV 18pF)
Capacitor (50WV 22PF)
Capacitor (16WV 47µF)
Capacitor (16WV 47µF)
Capacitor (25WV 100µF)
Capacitor (50WV 22µF)
Capacitor (330µF/25V SD)(VCEAGD1EW337M)
Capacitor (50WV 3300pF)(VCKYPA1HB332K)
Capacitor (50WV 3300pF)(VCKYPA1HB332K)
Capacitor (50WV 0.10µF)
Capacitor (50WV 0.033µF)
Capacitor (50WV 0.10µF)
Diode (1N4002G)
Diode (DSS133HV)
Diode (DSS133HV)
Diode (DSS133HV)
ZENER DIODE (MTZJ 7.5B)
IC (KID65083AP)
IC (LB1268)
REGULATOR IC (MCT7806CT)
LED (2 SEGMENT)(D568GWA)
Resistor (1/4W 100Ω ±5%)
Resistor (1/4W 1.0KΩ ±5%)
Resistor (1/4W 10KΩ ±5%)
Resistor (1/4W 1.0MΩ ±5%)
Resistor (1/4W 22Ω ±5%)
Resistor (1/4W 2.7KΩ ±5%)
Resistor (1/4W 330KΩ ±5%)
Resistor (1/4W 470Ω ±5%)
Resistor (1/4W 47KΩ ±5%)
Resistor (1/4W 47KΩ ±5%)
Resistor (1/4W 5.6KΩ ±5%)
Resistor (1/4W 56KΩ ±5%)
Resistor (1/4W 6.8KΩ ±5%)
Resistor (1/4W 68KΩ ±5%)
Resistor (1/16W 0Ω ±5%)(Jumper/1608Type)
Resistor (1/16W 1.0KΩ ±5%)
Resistor (1/16W 100KΩ ±5%)
Resistor (1/16W 4.7KΩ ±5%)
Resistor (1/16W 56KΩ ±5%)
CHIP RESISTOR (1/10W 110Ω ±5% 1608)
CHIP RESISTOR (1/10W 110Ω ±5% 1608)
CHIP RESISTOR (1/10W 110Ω ±5% 1608)
CHIP RESISTOR (1/10W 110Ω ±5% 1608)
Transistor (2SC3198)
Transistor (2SD2170)
Transistor (KTA1271)(VS2SA1271-/-1)
Screw (3×6)
MAIN PWB UNIT
5 Slide SW I/F PWB unit
NO.
PARTS CODE
1 QCNCW2908BHZZ
(Unit)
901 C P W B F 2 9 1 6 B H 0 1
PRICE NEW
RANK MARK
AG
N
AV
N
PART
RANK
C
SW CONNECTOR (5229-05APB)
E
DESCRIPTION
SLIDE SW I/F PWB UNIT
6 Articles for consumption
NO.
PARTS CODE
1 DPAPR1025CSZZ
2 NROLR1022CC05
PRICE NEW
RANK MARK
AV
BA
PART
RANK
S
Roll paper (5 rolls/pack)
S
Ink roller
–6–
DESCRIPTION
[F2]
[SW1]
[BZ]
[C2]
[C7,C11,C14,C15,C16]
[X2]
[X1]
[IC2]
[C17,C18,C19,C20,C21]
[C12]
[C13]
[C30 (G3-VDD JUMPER)]
[C6]
[C4]
[C9]
[C3]
[C22,C23,C24,C25]
[C29 (G3-JP1)]
[C8]
[C1]
[C5,C10]
[D1,D2,D3,D4,D5,D6]
[D7,D8,D9,D10,D12]
[D13,D14,D15,D16,D17]
[D18,D19,D20]
[ZD1]
[IC4,IC5]
[IC3]
[IC1]
[LED1,LED2,LED3,LED4]
[R70]
[R11,R28,R29,R30]
[R31,R32,R33]
[R2]
[R1]
[R10]
[R54,R56,R58,R60]
[R25]
[R15,R16,R17,R18]
[R19,R20,R23,R24]
[R4]
[R5,R12,R13]
[R55,R57,R59,R61]
[R3]
[R26]
[R7,R8]
[R6]
[R9]
[R14]
[R34,R35,R36,R37,R38]
[R39,R40,R41,R42,R43]
[R44,R45,R46,R47,R48]
[R49]
[Q3]
[Q1,Q2]
[Q6,Q7,Q8,Q9]
[IC1]
XE-A101U/A
■
Index
PARTS CODE
[C]
CCAS-2333BHZZ
CKNBZ2427BHZZ
CLOK-6673BHZZ
CPWBF2915BH01
"
CPWBF2916BH01
"
CSHEP2942BHZZ
[D]
DPAPR1025CSZZ
DUNT-1306BHZA
[G]
GBOXD7157BHZZ
GCABB2567BHZZ
GCABM2568BHZZ
GCAS-2333BHZZ
GCAS-2335BHZZ
GCOVB2523BHZZ
GCOVB2524BHZZ
GCOVH2525BHZZ
GFTAB2445BHZZ
[H]
HDECP2370BHZZ
[J]
JKNBZ2428BHZZ
[K]
KI-OB6774BHZZ
KI-OK2369BHZZ
[L]
LANGK2904BHZZ
"
LANGK2905BHZZ
LBRC-2002BHZZ
LFRM-2365BHZZ
LHLDZ2388BHZZ
LKGIM7331BHZZ
"
LKGIW7330BHZZ
LPLTM2365BHZZ
LPLTM2366BHZZ
LPLTM2367BHZZ
LPLTM2372BHZZ
LX-BZ6775BHZZ
[M]
MCAMM6633BHZA
MLEVF2338BHZZ
MLEVF6699BHSA
MSPRC6743BHZZ
MSPRC6748BHZZ
MSPRK6718BHZZ
MSPRT6731BHZZ
MSPRT6742BHZZ
[N]
NROLP6655BHZA
NROLP6657BHZZ
NROLR1022CC05
NSFTA6655BHZZ
[P]
PCUT-6652BHZZ
PFILW2010BHZZ
PGIDH2403BHZZ
PGUMM2445BHZZ
PGUMM2446BHZZ
PRNGT6637BHZZ
PSHEP6826BHZZ
PSHEP6828BHZZ
[Q]
QACCD1010CCN1
QCNCM1060AC03
QCNCM1101BHZZ
QCNCM6865BH0B
QCNCM7057BHZZ
QCNCW1057ACZZ
QCNCW2908BHZZ
"
QCNCW2942BHZZ
QCNCW2943BHZZ
QCNCW6882BH0H
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
2-501
1- 37
2-502
1- 22
4-901
1- 27
5-901
1- 34
BF
BD
BA
BP
BP
AV
AV
AZ
N
N
N
N
N
N
N
N
E
C
E
E
E
E
E
B
6- 1
2- 35
AV
AX
2-901
1- 4
2- 13
2- 28
2- 45
1- 1
1- 16
2- 7
1- 9
BT
BD
BE
BA
AU
AS
AS
AG
AG
N
N
N
N
N
N
N
N
N
E
D
D
D
D
D
D
D
D
1-
8
AM
N
D
1- 24
AE
N
C
1- 14
1- 26
BE
BF
N
E
E
14221123212222-
28
1
40
22
32
18
30
11
29
35
8
37
38
16
AH
AH
AN
AN
AW
AE
AE
AE
AY
AV
AM
AW
AQ
AA
22222222-
33
17
23
21
41
32
24
18
AE
AF
AF
AG
AD
AF
AD
AD
2- 26
2- 20
6- 2
2- 44
AF
AN
BA
AE
11111223-
2
7
6
33
19
31
14
4
AF
AP
AG
AY
AC
AA
AE
AF
2- 3
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
5- 1
4- 9
4- 8
1- 40
AP
AB
AC
AB
AB
AB
AG
AG
AF
AF
AF
QCNCW6882BH0H
QCNCW7081BHZZ
QCNW-3152BHZZ
QCNW-3153BHZZ
QCNW-3154BHZZ
QCNW-3155BHZZ
QCNW-3181BHZZ
QFS-H0002QCZZ
QFSHD2109AFZZ
QFS-K2005BHZZ
QSW-S2411BHZZ
QTANZ2348BHZZ
QTANZ2349BHZZ
QTANZ2350BHZZ
QTANZ2351BHZZ
[R]
RALMB5006SCZZ
RC-EZ0011QCZZ
RC-KZ1054CCZZ
RCRMZ6007RCZZ
RCRSP6676RCZZ
RH-IX2004BHZZ
RMOTM2321BHZZ
RPLU-6644BHZA
RTRNP2426BHZZ
[S]
SPAKA3175BHZL
SPAKA3175BHZR
SPAKA8339BHZZ
SPAKC3176BHSA
SPAKC3176BHZZ
SSAKH3012CCZZ
SSAKH3015CCZZ
SSAKH4231CCZZ
[T]
TCADH2395BHZZ
TCADH2402BHZZ
TCADH2403BHZZ
TCAUZ6681BHZZ
TGANE6644BHSC
TINSE2457BHZZ
TINSE2464BHZZ
TINSF2465BHZZ
TINSS2458BHZZ
TLABR2549BHZZ
TLABR2550BHZZ
TLABZ2548BHSA
TLABZ2548BHZZ
[U]
UREL-6629BHZZ
[V]
VCCCPU1HH101J
VCCCTV1HH180J
VCCCTV1HH220J
VCEAGA1CW476M
VCEAGA1EW107M
VCEAGA1EW337M
VCEAGA1HW226M
VCKYPU1HB332K
VCKYTV1HF104Z
VCQYNA1HM333K
VCQYNU1HM104K
VHD1N4002G/-1
VHDDSS133HV-1
VHEMTZJ7R5B-1
VHIKID65083AP
VHILB1268//-1
VHIMC7806CT-1
VHPD5680GL2-1
VRD-RC2EY101J
VRD-RC2EY102J
VRD-RC2EY103J
VRD-RC2EY105J
VRD-RC2EY221J
VRD-RC2EY272J
VRD-RC2EY331J
VRD-RC2EY471J
VRD-RC2EY473J
VRD-RC2EY562J
VRD-RC2EY563J
VRD-RC2EY682J
S
E
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
D
C
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
S
C
N
N
N
N
N
N
N
N
N
C
D
C
C
C
C
C
D
B
C
C
C
C
C
C
C
C
C
C
–7–
NO.
PRICE
RANK
NEW
MARK
PART
RANK
442114444441111-
10
11
5
21
38
12
13
14
15
16
17
13
11
12
10
AF
AB
AH
AF
AF
AH
AF
AF
AC
AF
AK
AF
AG
AG
AE
444444122-
18
19
20
21
22
23
20
15
2
AD
AH
AB
AD
AG
BA
AS
AX
AX
3- 2
3- 5
3- 20
3- 1
3- 1
3- 10
3- 7
3- 6
AX
AX
AC
BC
BC
AA
AA
AA
N
N
3333333333333-
16
16
16
9
15
8
8
8
8
13
13
14
14
AQ
AQ
AQ
AD
AE
AR
AR
AR
AR
AG
AG
AL
AL
N
N
N
3-
3
AN
C
444444444444444444444444444444-
24
25
26
27
28
30
29
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
AB
AA
AA
AB
AB
AC
AB
AA
AA
AA
AB
AA
AA
AC
AM
AK
AG
AQ
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
A
C
A
B
C
C
C
C
B
C
C
B
B
B
B
B
B
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
XE-A101U/A
PARTS CODE
VRD-RC2EY683J
VRS-CY1JD000J
VRS-CY1JD102J
VRS-CY1JD104J
VRS-CY1JD472J
VRS-CY1JD563J
VRS-CY2AY111J
VS2SC3198-/-1
VS2SD2170//-1
VSKTA1271//-1
[X]
XBBSD30P06000
"
XBPSD26P04000
XBPSD40P06K00
XEBSD30P08000
"
XJBSD20P04000
XJPSD30P06000
XJPSD30P10X00
"
XNESD60-50000
XRESJ50-06000
NO.
PRICE
RANK
4444444444-
54
55
56
57
58
59
60
61
62
63
AA
AA
AA
AA
AA
AA
AA
AL
AH
AE
141212111222-
25
64
17
19
15
36
3
36
5
1
25
34
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AA
AA
NEW
MARK
N
PART
RANK
PARTS CODE
C
C
C
C
C
C
C
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
–8–
NO.
PRICE
RANK
NEW
MARK
PART
RANK
COPYRIGHT  2001 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Digital Document Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-1186, Japan
2001 August Printed in Japan