Download 32Z3522 402S Service Manual USA issue 6.pub

Version 2.0
Merrychef
402s
US Models including WAWA
SE RV I CE & PA RT S M AN UA L
This manual covers US models manufactured from:
Version 2.0 Serial No. 000745 –001199
Version 3.0 Serial No. 001200 onwards
ISSUE 6
18.03.2008
SERVICE MANUAL
Version 3.0
CAUTION MICROWAVE EMISSIONS
DO NOT BECOME EXPOSED TO EMISSIONS FROM THE MICROWAVE
GENERATOR OR PARTS CONDUCTING MICROWAVE ENERGY
402s Ovens Pt. No. 32Z3522 Issue 6
1
TABLE OF CONTENTS
Microwave safety precautions .................................................3
Safety code..............................................................................4
Product specifications..............................................................5
Installation instructions ............................................................6
Main features ......................................................................7– 9
Principal components: RHS...................................................10
Principal components: LHS ...................................................11
Principal components: Top ....................................................12
Principal components: Back View..........................................13
Principal components: Power Supply ....................................14
Principal components: Cavity Parts .......................................15
Principal components: External Panels .................................16
Principal components: Control Panel.....................................17
Parts Matrix...................................................................... 18-19
Procedure for Microwave Emission test .......................... 20-21
Procedure for Power output measurement............................22
Procedures for Principal Component tests ..................... 23-24
Procedure for door interlock adjustment.......................... 25-26
Hot Air Motor and controller............................................. 27-28
Wiring Diagrams ....................................................................29
Trouble Shooting Guide................................................... 30-34
Appendix 1: Temperature Probe............................................35
Appendix 2: MenuKey Procedures .................................. 36-37
Appendix 3: Cleaning Procedure ..................................... 38-40
Appendix 4: Recommended Spares List ......................... 41-42
Appendix 5: PCB connection Points ................................ 43-44
Appendix 6: Engineering Test Settings..................................45
Appendix 7: Firmware revision guide............................... 46-51
Merrychef USA
1111 North Hadley RD
Fort Wayne
IN 46804
Phone: 800/678 - 9511
Fax: 800/285 - 9511
e-mail: [email protected]
402s Ovens Pt. No. 32Z3522 Issue 6
2
MICROWAVE SAFETY PRECAUTIONS
CAUTION
WARNING TO SERVICE TECHNICIANS
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING
SERVICING TO AVOID POSSIBLE EXPOSURE TO
EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before
activating the magnetron or other microwave source, and make repairs
as necessary:
1) interlock operation.
2) proper door closing.
3) seal and sealing surfaces (arcing, wear, and other damage).
4) damage to or loosening of hinges and latches.
5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection
within the microwave generating compartments, check the magnetron,
wave guide or transmission line, and cavity for proper alignment,
integrity and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door
seal, and microwave generation and transmission systems shall be
repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.
(e)(i) For U.S.A.
A microwave leakage check to verify compliance with the Federal
Performance Standard should be performed on each oven prior to
release to the owner.
(e)(ii) For CANADA.
A microwave leakage check to verify compliance with the Canadian
Regulation, HEALTH AND WELFARE, SOR/79 920 should be performed
on each oven prior to release to the owner.
402s Ovens Pt. No. 32Z3522 Issue 6
3
SAFETY CODE
This manual is designed to assist engineers who have been on a recognised product familiarisation
and training course run by Merrychef. It has been prepared to offer technical guidance for the 402s
range of Ovens.
Please remember that it is wiser not to attempt a service task if you are unsure of being able to
complete it competently, quickly, and above all safely.
To avoid injury to yourself, and to protect the appliance from possible damage, please follow this
Safety Code when servicing these ovens.
Before attempting to repair the oven, check it for microwave emission using a calibrated
emission detector.
Check that the oven is not emitting microwaves, even when supposedly not in operation.
Check that the oven is not operating continuously, whether the display indicates cooking or
not.
Always discharge the HT capacitors before working on the oven using a suitably insulated
10 MΩ Resistor.
When testing the oven with covers off run for short periods of time only or magnetrons will
overheat and the display will show Error condition.
Before removing any covers from the oven, do all of the following.
• Switch off the mains supply and remove the plug from the wall socket.
•
or
If the oven is hard wired, ensure that the power is turned off at the isolator switch.
Note:
The On/Off switch on the oven is not adequate protection against electric
shock, as it does not isolate all of the internal wiring from the mains.
Upon completion of a service the oven, or before reconnecting the appliance to the electrical
supply for testing, check all of the following points:
•
•
•
•
•
•
•
All internal electrical connections are correct (see wiring diagrams).
All wiring insulation is correct and is not touching a sharp edge.
All grounding connections are electrically and mechanically secure.
All door safety interlocks are secure and mechanically sound.
The door operation is smooth, and the arms run freely in the slots.
The door activates all four of the door interlock switches and in the correct order
The temperature sensor is correctly connected to the Power PCB.
Before finishing a service call, recheck the following points:
•
•
•
•
All of the electronics are functioning correctly and all of the touch pads are working.
Microwave emissions are below permissible limit of 4 mW/cm².
The power output of the oven is checked in accordance with the procedure page.
Oven has correct 2 inch ( 50mm ) air gap all round and 2 inches ( 50mm ) above.
Air flow should not be restricted.
402s Ovens Pt. No. 32Z3522 Issue 6
4
PRODUCT SPECIFICATIONS
Model Number:
402S VVV F P C R TT ZZ
Example 402S2086DK3GMUS
Model No. EC402s
208V, 60Hz, 2P + GND supply, MenuKey Revision 3, General Market, USA
Supply
Voltage
Freq.
Hz
Phase/Supply
Control
Type
Rev
Type
Country
/Region
VVV
F
P
C
R
TT
ZZ
1
2
3
GM =
General
Market
Voltage (ac)
208 = 208V
220 = 220-230V
240 = 230-240V
5=
50Hz
Phase Arrangement
A=
L + N + E (30 Amp)
6=
60Hz
B=
L1 + L2 + N + E
K=
Electronic
MenuKey
C=
2 P + Gnd (20 Amps)
D=
2 P + Gnd (30 Amps)
Power
Requirements
208Volts
240Volts
Power Output
Microwave 100% 1500watts
Convection
3250watts
External
Dimensions
Height
23.0 inches
Width
23.0 inches
Depth
27.5 inches
Weight
Nett
198lb.s ( 90kg )
Construction
Cavity
Casework
304 Stainless Steel
208V ac 60Hz 30Amp 2P & G
240V ac 60Hz 40Amp 2P & G
402s Ovens Pt. No. 32Z3522 Issue 6
5
US =
USA
INSTALLATION INSTRUCTIONS
Installation Instructions for Mealstream Combination Ovens
Power Supply Requirements
The Mealstream Series should be connected to a suitable electricity supply, which can cope
with the switching-on surge that occurs with certain types of catering equipment, including
microwaves. Because of this requirement, we strongly recommend that a separate, suitably
rated supply is installed for the oven.
The supply for the oven should be fitted with a Type "C" or Time Delay circuit breaker.
If the oven is hard-wired to the supply, a double-pole isolator switch with a contact gap of at
least 1/8 inch ( 3 mm ) should be fitted.
Grounding requirement
This appliance must be connected to a grounded, metallic, permanent wiring system, or an
equipment grounding conductor should be run with the circuit conductors and connected to the
equipment grounding terminal or lead on the appliance.
Positioning the Oven
In order to maintain adequate ventilation for air intake
and exhaust, and to allow access for cleaning filters,
you must allow a minimum of 2 inches ( 50 mm )
clearance at the sides and rear of the oven.
Air intake temperature should not exceed 110°F/45°C
excessive temperature will lead to reduced operating duty
cycle, or premature ageing of internal components.
Failure to comply with these conditions will invalidate the
warranty.
NEVER
Install an oven above fryers,
grills, griddles or any other
major heat source.
ALWAYS Place containers in the cavity
carefully - impact damage
may chip the vitreous enamel
coating on the runners and
baffle plate.
Note:
The minimum recommended
clearance required for air flow
402s Ovens Pt. No. 32Z3522 Issue 6
6
MAIN FEATURES
m
a
j
b
L
f
g
d
c
e
L
i
h
k
k
a On/Off SWITCH
h DOOR
This is used to turn the oven On or Off.
IT DOES NOT ISOLATE INTERNAL WIRING
FROM THE MAINS SUPPLY.
The door consists of a thermally insulated inner
section, and an additional air gap provided by a
twin skinned door front to lower the surface
temperature.
b MenuKey
i DOOR SEAL
The MenuKey System automatically changes
all the cooking programs with an electronic key
and allows program names to be identified.
These ensure a tight seal around the door.
They should be kept clean and checked
regularly for signs of damage. Replace if worn
or damaged.
c OVEN CAVITY
The oven cavity is mainly constructed from
stainless steel panels. It must be kept clean.
j ELECTRICAL SUPPLY CORD
Electrical supply cord is situated on the rear of
the oven,
d GREASE FILTER
The grease filter must be cleaned on a regular
basis, and kept free of debris.
k AIR FILTERS
Main intake for cooling air for internal
components. Must be clear of obstructions.
e RACK
The cooking rack should be removed daily and
cleaned
L
IMPINGER PLATES ( Upper & Lower)
Direct the air in the cavity. They must be
cleaned on a regular basis, and kept free of
debris
f HOT AIR FAN
Situated behind the grease filter and circulates
the hot air through the cavity.
m STEAM VENT PIPE
g RATING PLATE
Vents steam from the oven cavity
The rating plate is situated on the rear of the
oven, and states the Model, Serial Number,
Electrical Ratings and Manufacturers
telephone number.
402s Ovens Pt. No. 32Z3522 Issue 6
7
MAIN FEATURES
Electronic control panel: Version 2.0
FAN SPEED PADS
PREHEAT/ COOL DOWN
PROGRAM
MAIN DISPLAY
PANEL
POWER PADS
TIME/ PROGRAM PADS
CANCEL PAD
Cancels all timed cooking cycles, pre-programmed
operations and stops the microwave energy. It does
not alter the oven temperature. If the oven is hot,
food will continue to cook and should be removed
from the oven immediately. This pad will also cancel
any incorrect operations. It will not erase programs.
FAN SPEED PADS
The Fan speed can be increased and decreased in
5% steps ( 10% to 100% )
FUNCTION PADS
Move through control functions in the Main Display
MAIN DISPLAY PANEL
Shows the principal functions of the oven.
When cooking, the time remaining counts down.
Also displays error messages and oven temperature.
(See TROUBLESHOOTING )
When storing and recalling a program the display
indicates the program number and details
FUNCTION
PADS
START
MenuKey
CANCEL
PAD
MenuKey
The MenuKey System automatically changes all the
cooking programs with an electronic key and allows
program names to be identified.
POWER PADS
The microwave power can be increased or
decreased adjusted in 10% steps. ( 0% to 100% )
The default setting is 50% microwave power.
PREHEAT/ COOL DOWN
Commences main oven heating cycle to a preset
temperature. Press and hold for 5 seconds to
commence cool down procedure ( See CLEANING )
PROGRAM
Activates program mode for storing programs in
memory START PAD Commences a program
TIME/ PROGRAM PADS
These pads are used for setting the cooking time in
1 second steps to a maximum of 10 minutes.
They are also used for storing and recalling
programs from 0-499
Display Panel error messages
Message
Condition
Possible cause
ERROR MAGNETRON 1
Magnetron 1 has overheated
ERROR MAGNETRON 2
Magnetron 2 has overheated
ERROR MAGNETRON 1 & 2
Magnetron 1 and 2 have
overheated
Blocked Air filter(s)
Oven located near hot air sources
Oven being used empty
Cooling fan failure
Magnetron failure
CAVITY SENSOR ERROR
Cavity temperature exceeds
more than 90°F above
PREHEAT temperature
setting during cook cycle
Indicates combustion ( fire ) in
oven cavity
Note: In service operations when
PREHEAT is set to 0°F this
message can appear when the
oven is operated
402s Ovens Pt. No. 32Z3522 Issue 6
8
MAIN FEATURES
Electronic control panel: Version 3.0
MAIN DISPLAY
PANEL
COOL DOWN
FUNCTION
PADS
FUNCTION
PADS
MenuKey 2
The MenuKey System automatically changes all the
cooking programs with an electronic key and allows
program names to be identified
CANCEL PAD
Cancels all timed cooking cycles, pre-programmed
operations and stops the microwave energy. It does
not alter the oven temperature. If the oven is hot, food
will continue to cook and should be removed from the
oven immediately. This pad will also cancel any
incorrect operations. It will not erase programs.
FUNCTION
PADS
MenuKey
CANCEL
PAD
DISPLAY PANEL
Shows the principal functions of the oven.
When cooking, the time remaining counts down.
Also displays error messages and oven
temperature. When storing and recalling a
program the display indicates the program
number and details.
FUNCTION PADS
The function pads select options shown in the
DISPLAY PANEL.
COOL DOWN PAD
Puts the oven into Cool Down Mode prior to
cleaning
Error Message
Condition
Possible Cause
Magnetron 1 Overheat
Magnetron 1 has overheated
Magnetron 2 Overheat
Magnetron 2 has overheated
Magnetron 1 & 2 Overheat
Magnetron 1 & 2 have overheated
Blocked air filters
Ensure air filters are clean
Oven located near hot air source
Oven being used empty
Cooling fan failure
Magnetron failure
Allow oven to cool
Magnetron 1 FAILED
Magnetron 1 failed
No microwave output check power
supply
Magnetron 2 FAILED
Magnetron 2 failed
No microwave output check power
supply
Ambient Overheat
Temperature inside casing has
exceeded limit
Blocked air filters
Restricted airflow to air filters
Oven located near hot air source
Circulation fan failure
Combustion (fire) in cavity
Cavity Overheat
Cavity temperature has exceeded
more than 565°F
Blocked air filters
Restricted airflow to air filters
Combustion (fire) in cavity
Heater Failure
Cavity has not reached a
temperature of 100°F in 10 minutes
One or more heater elements have failed
and need to be replaced
402s Ovens Pt. No. 32Z3522 Issue 6
9
PRINCIPAL COMPONENTS: Right Side
1
5
6
6
7
2
8
3
25A
71
25
4
70
No.
Description
Part No.
1
Cavity High limit Stat
30Z1024
2
Motor Start Capacitor 2µF ( Blue )
30Z1298
3
Filter 16A
30Z1340
4
Air filter
SA276
5
Stirrer motor Assembly
SA288
5A
Stirrer (inside cavity)
SA291
5B
Stirrer Gear
6
6A
DV0552
Microswitch SW1
Microswitch SW2
30Z1294
Microswitch Assembly
SA212
7
Door Hinge Assembly RH
SA202
8
Magnetron Cooling Fan
30Z1295
25
HV Capacitor 2500V 0.88μF ( 60HZ models )
30Z1251
HV Capacitor clip
31Z1261
70
Fibre Optic Diode Board
11M0364
71
Solid State Relay
30Z1362
25A
402s Ovens Pt. No. 32Z3522 Issue 6
10
PRINCIPAL COMPONENTS: Left Side
5A
5
24
5B
6
6
9
3
25A
10
25
70
4
No.
Description
Part No.
3
Filter 16A
4
Air filter
SA276
5
Stirrer motor Assembly
SA288
5A
Stirrer (inside cavity)
SA291
5B
Stirrer Gear
6
6A
30Z1340
DV0552
Microswitch SW3
Microswitch SW4
30Z1294
Microswitch Assembly
SA212
9
Door Hinge Assembly LH
SA203
10
Motor Controller
30Z1293
25
HV Capacitor 2500V 0.88μF ( 60Hz models )
30Z1251
HV Capacitor clip
31Z1261
Fibre Optic Diode Board
11M0364
25A
70
402s Ovens Pt. No. 32Z3522 Issue 6
11
PRINCIPAL COMPONENTS: Control Box
See
Principal
components:
POWER
SUPPLY
11
12
11
16
13
17
13A
14
18
15
59
72
No.
Description
Part No.
11
Fuse 10A HRC
30Z0217
12
Gold resistor ( 220R )
30Z0235
13
Relay PCB Assembly
11K0004
14
Ribbon Cable 15way
11Z0298
15
Ribbon Cable 10way MenuKey
11M0117
16
Logic PCB Assembly Version 2.0
SA231
16
Logic PCB Assembly Version 3.0
SA260
17
Transformer LT (Low voltage)
30Z1155
18
Fuse 1A
30Z0957
59
Sounder
SA257
72
Fibre Optic Logic PCB
11K0013
75
Relay PCB Fuse
30Z0470
402s Ovens Pt. No. 32Z3522 Issue 6
12
PRINCIPAL COMPONENTS: Back view
73
74
20
21
21
22
22
23
20
28
27
27
No.
Description
Part No.
20
Heater Element 208V 650W 68Ω
DV0328
20
Heater Element 240V 650W 88Ω
DV0337
20A
Heater Element Collar
DV0058
21
Magnetron
22
Magnetron Thermistor Assembly ( Each magnetron)
SA234
23
Convection ( Hot Air ) Motor Assembly
SA208
24
Thermistor Cavity
30Z1315
27
Transformer 208/220/240V 60Hz
30Z1230
28
HT Rectifier (No Fibre Optic)
11H0010
73
Magnetron Cooling Duct LH
DV0039
74
Magnetron Cooling Duct RH
DV0040
30Z1349
402s Ovens Pt. No. 32Z3522 Issue 6
13
20A
PRINCIPAL COMPONENTS: Power Supply
19
3
29
31
32
30
11
34
No.
Description
Part No.
3
Filter 16A
30Z1340
11
Fuse 10A HRC
30Z0217
19
Cable Gland
31Z0500
19
Cable Gland Nut
31Z0499
29
Electrical Supply Lead Assembly
30
Terminal Block
31Z0447
31
Fuse 20A FLM
30Z1177
32
Fuse Holder 30A
30Z1178
34
Fuse Holder 10A
30Z0231
402s Ovens Pt. No. 32Z3522 Issue 6
14
SA217
PRINCIPAL COMPONENTS
Cavity parts
35
36
36
38
39
40
No.
Description
Part No.
35*
Grease Filter Cartridge
Filter Housing
36
Stirrer Glass
DV0492
37*
Rack Support V2.5 ( Not shown )
DV0114
38
Upper Impinger plate
39
Rack V3.0
Rack V2.5
40
Lower Impinger plate
SA340
SA339
SA211
DV0275
DV0158
SA266
* Parts 35 & 37 Contact Service Department
KFC Accessories
62
63
60
64
61
65 Chicken Griddle SA133
No.
Description
Part No.
60
Cool-down pan
32Z4028
61
Oven tray
MC3175
62
Handle
SA267
63
Griddle
DV0221
64
Griddle carrier
SA350
65
Chicken Griddle (SA350 + DV0221 + DV0267)
SA133
402s Ovens Pt. No. 32Z3522 Issue 6
15
PRINCIPAL COMPONENTS
External Parts
Control Panel
See page 15
41
52
51
42
50
43
4
52
4
Door Assembly
76
77
49
78
48
45
47
46
No.
Description
Part No.
4
Air Filter
SA276
41*
Top Trim
DV0187
42*
Rear Panel
43*
Side Panel LH
DV0091
45
Door Skin
DV0501
46
Door Handle
47*
Door Inner
48*
Door Choke
DV0168
49
Door Seal
DV0305
50*
Bottom Trim
DV0037
51*
Side Panel RH
DV0092
52*
Door Assembly
SA111
76
Cage Nut (Door Choke Plate)
77
Screw M3 Csunk ( Doorskin)
78
Door Handle spacer
SA329
32Z1066
SA331
105005
31Z3094
DV0309
*Note:
On Ovens with Serial No.s before 000745 ( WAWA Models )
External Panels Items 41,42, 43, 45, 47,48, 50, 51, 52 are only available to special order.
402s Ovens Pt. No. 32Z3522 Issue 6
16
PRINCIPAL COMPONENTS
Electronic Control Panel Assembly
Version 2.0/2.5 & WAWA
54
55
53
56
Version 3.0
57
58
66
54
53
*Note:
On Ovens with Serial No.s
before 000745
( WAWA Models)
External Panels Item 51 is
only available to special order.
67
68
58
No.
Description
Part No.
53
MenuKey Dust Cover
DV0052
54
Power switch (On/Off)
30Z1318
55
GM Membrane Version 2.0 & 2.5
DV0055
Membrane WAWA version
DV0192
56*
Front Panel Version 2.0
DV0036
57
Display Assembly & Header Version 2.0
30Z1299
58
MenuKey Socket
11K0005
66
GM Membrane Version 3.0
DV0254
67
Front Panel Version 3.0
DV0249
68
Display Assembly & Header Version 3.0
402s Ovens Pt. No. 32Z3522 Issue 6
17
30Z1324
Part number identification chart 1
Ref. No.
Description
Part No.
1
Cavity High limit Stat
30Z1024
2
Motor Start Capacitor 2µF ( Blue )
30Z1298
3
Filter 16A
30Z1340
4
Air filter
5
SA276
Stirrer motor Assembly
SA288
5A
Stirrer (inside cavity)
SA291
5B
Stirrer Gear
6
6A
DV0552
Microswitch SW1, SW2, SW3, SW4
30Z1294
Microswitch Assembly
SA212
7
Door Hinge Assembly RH
8
Magnetron Cooling Fan
9
Door Hinge Assembly LH
10
Motor Controller
30Z1293
11
Fuse 10A HRC
30Z0217
12
Gold resistor ( 220R )
30Z0235
13
Relay PCB Assembly
11K0004
14
Ribbon Cable 15way
11Z0298
15
Ribbon Cable 10way MenuKey
11M0117
16
Logic PCB Assembly Version 2.0
16
Logic PCB Assembly Version 3.0
17
Transformer LT (Low voltage)
30Z1155
18
Fuse 1A
30Z0957
19
Cable Gland
31Z0500
Cable Gland Nut
31Z0499
20
20A
SA202
30Z1295
SA203
SA231
SA260
Heater Element 208V 650W
DV0576
Heater Element 220V 650W
DV0606
Heater Element 240V 650W
DV0607
DV0058
Heater Element Collar
30Z1349
21
Magnetron
22
Magnetron Thermistor Assembly
23
Convection ( Hot Air ) Motor Assembly
24
Thermistor Cavity
30Z1315
25
HV Capacitor 2500V 0.88μF ( 60Hz Models )
30Z1251
HV Capacitor clip
31Z1261
27
Transformer 208/220/240V 60Hz
30Z1230
28
HT Rectifier
11H0010
29
Electrical Supply Lead Assembly
30
Terminal Block
31Z0447
31
Fuse 20A FLM
30Z1177
32
Fuse Holder 30A
30Z1178
34
Fuse Holder 10A
30Z0231
35*
Grease Filter ( 2 parts )
25A
SA234
SA208
SA217
SA339
SA340
402s Ovens Pt. No. 32Z3522 Issue 6
18
Part number identification chart 2
Ref. No.
Description
Part No.
36
Stirrer Glass
DV0492
37
Rack Support
DV0114
38
Upper Impinger plate
39
Rack
40
Lower Impinger plate
41*
Top Trim
42*
Rear Panel
43*
Side Panel LH
DV0091
45*
Door Skin
DV0501
SA211
DV0275
SA266
DV0187
SA329
46
Door Handle
47*
Door Inner
32Z1066
48*
Door Choke
DV0168
SA331
49
Door Seal
DV0305
50*
Bottom Trim
DV0037
51*
Side Panel RH
DV0092
52*
Door Assembly
SA111
53
MenuKey Dust Cover
DV0052
54
Power switch (On/Off)
30Z1318
55
Membrane WAWA version
DV0192
55
Membrane GM Version Version 2.0
DV0055
56
Front Panel Version Version 2.0
57
Display Assembly & Header Version 2.0
30Z1299
58
MenuKey Socket
11K0005
59
Sounder
60
Cool-down pan
32Z4028
61
Oven tray
MC3175
62
Handle
SA267
63
Griddle
DV0221
64
Griddle carrier
SA350
65
Chicken Griddle (SA350+DV0221+ DV0267)
SA133
66
GM Membrane Version 3.0
DV0254
67
Front Panel Version 3.0
DV0249
68
Display Assembly & Header Version 3.0
30Z1324
70
Fibre Optic Diode Board
11M0364
71
Solid State Relay
30Z1362
72
Fibre Optic Logic PCB
11K0013
73
Magnetron Cooling Duct LH
74
Magnetron Cooling Duct RH
75
Relay PCB Fuse
76
Cage Nut (Door Choke Plate)
77
Screw M3 Csunk ( Doorskin)
78
Door Handle spacer
DV0309
—
Stirrer cover sealant ( tube )
31Z0527
—
Grease Filter Cartridge
—
Microswitch interlock spring
DV0036
SA257
DV0039
DV0040
30Z0470
105005
31Z3094
SA340
31Z1247
402s Ovens Pt. No. 32Z3522 Issue 6
19
*Note:
On Ovens with
Serial No.s before 000745
( WAWA Models )
Grease Filter 35, Rack 39
External Panel Parts
41,42, 43, 45, 47, 48,
50, 51, 52
are only available
to special order.
PROCEDURE FOR MICROWAVE EMISSION TEST (1)
Warning
Check for radiation emission after servicing. Should the emission be more than 4mW/cm² Inform
Merrychef service centre immediately. After repairing or replacing any radiation safety device,
keep a written record for future reference, as required by D.H.H.S. and Health and Welfare
Canada regulation.
This requirement must be strictly observed. In addition, the emission reading must be recorded
on the service repair documentation while in the customer’s premises.
Please Note
DO NOT attempt to carry out the
following procedure unless you have
the following tools.
Tools required for microwave leakage test
1.0 Pint ( 600ml) glass beaker
Supply of cold water
Microwave leakage meter
Changing the Oven Profile
In order to carry out the test the oven PREHEAT
must be set to OFF[ V3.0 ] or 0ºF[ V2.0 ] to switch
off the convection heaters and the Manual
controls must be set to ON [ V3.0 ] or PROGRAM/
MANUAL[ V2.0 ].
When the test is completed the oven must be
returned to its original settings or the appropriate
MenuKey can be used to reset the oven
automatically.
See Appendix 6 for changing the Oven Profile
Read and understand all of these notes and procedure before carrying out this operation.
Note before measuring.
•
Make sure that the survey meter you are using has been calibrated and is suitable for
measuring frequencies of 2,450 MHz.
•
Do not exceed meter full scale deflection, leakage meter should initially be set to the highest
scale, then adjusted down as necessary to ensure that low readings are measured on the most
sensitive range.
•
To prevent false readings, hold the probe on the grip provided and move along the areas
indicated on the following page.
The probe should be moved at 1 inch/second (2.5cm/second)).
•
With any casework removed the leakage should not exceed 4mW/cm².
•
When measuring the leakage, always hold the probe at 2inches (50mm) from the test area
using the probe supplied with the instrument.
•
Always hold the probe at right angles to the oven and point of measurement
Procedure:
1. Place 0.5 pint (275ml) of cold water in the 1.0 Pint ( 600ml ) glass
beaker.
2. Place the 1.0 Pint ( 600ml ) glass beaker in the centre of oven.
3. Set the leakage meter to the appropriate scale/range.
4. Set a time of 30 seconds with Fan speed at 10% and Power at 100%.
5. Press Start and move the survey meter probe along the areas
indicated on page 21. Open the door at 30 seconds and taking care
change the water. If the water boils the meter readings will be
inaccurate.
On completing the test remember to return the Oven Profile and
PREHEAT temperature to the original settings.
402s Ovens Pt. No. 32Z3522 Issue 6
20
Manual Mode
If the manual mode
screen does not
appear it must be
changed in the
OVEN PROFILE see
Appendix 6
PROCEDURE FOR MICROWAVE EMISSION TEST (2)
•
Readings must be below 4mW/cm². If a level greater that 4mW/cm² is observed,
this should be reported to Merrychef Service Division immediately.
•
In any case, notes should be kept of the leakage that is observed. In terms of level and
position on the oven. This should be kept with the service documentation.
Test for microwave leakage at all points marked with a
Control Panel
Door Perimeter
Door Perimeter
Rear Cover/ vents
402s Ovens Pt. No. 32Z3522 Issue 6
21
PROCEDURE FOR POWER OUTPUT MEASUREMENT
The power output specification 1500W on this model is established under IEC 705 standard
method. This method is only workable in Laboratory controlled conditions.
An approximate method is as follows:
Ensure the oven is cold before commencing the test
Changing the Oven Profile
In order to carry out the test the oven PREHEAT
must be set to OFF[ V3.0 ] or 0ºF[ V2.0 ] to switch
off the convection heaters and the Manual
controls must be set to ON [ V3.0 ] or PROGRAM/
MANUAL[ V2.0 ]
When the test is completed the oven must be
returned to its original settings or the appropriate
MenuKey can be used to reset the oven
automatically.
See Appendix 6 for changing the Oven Profile
Test procedure:
1. Fill one beaker ( glass or plastic ) with 2.11 pints ( one litre ) of tap water
at about 68ºF ( 20ºC ) and measure the water temperature.
( Use a thermometer with a 1/10, 0.1 degree gauge ).
2. Place the beaker in the centre of the cold cavity.
3. Version 2.0 Press the Manual Function Pad to enter Manual Mode
Version 3.0 Press the lower RH function pad below the display to enter
Manual Mode
Set Time to 1 minute 3 seconds, Power to 100% and Fan to 0%.
Press the Start pad and wait until the counter reaches zero.
4. Take the beaker out immediately stir the water with a plastic implement
and measure the water temperature.
Manual Mode
If the manual mode
screen does not
appear it must be
changed in the
OVEN PROFILE see
Appendix 6
Calculate the temperature rise of water in the beaker.
The temperature rise of the water should be within the following range:
Temperature Rise
27ºF ( 15ºC ) Minimum
36ºF ( 20ºC ) Maximum
Note:
Power Output is affected by the line voltage under load.
For correct Power Output measurement the line voltage under load must be correct.
402s Ovens Pt. No. 32Z3522 Issue 6
22
PROCEDURES FOR PRINCIPAL COMPONENTS TEST (1)
1. Power Transformer Test
You will need:
A Digital Multi-meter (D.M.M.)
A Megger or similar resistance meter using 500V d.c.
WARNING: High voltages and large currents are present at the High Voltage Capacitor. It is very
dangerous to work near this part when the oven is on. NEVER make any voltage
measurements at the High Voltage circuits, including the magnetron filament.
WARNING: Even when the oven is not cooking, the High Voltage Capacitor has High Voltages
present because of the Soft Start circuit. Isolate the oven before testing.
See Safety Code ( Page 4 )
1
2
3
4
5
Isolate the oven from the mains supply.
Ensure that the High Voltage Capacitor is discharged before commencing work.
Remove all connections from the Power Transformer.
Using a D.M.M., check the resistance of the windings. Results should be as follows:
a
Mains winding between tags
Approx. 1.1 Ω
b
High Voltage winding
Approx. 60 Ω
c
Filament winding
between terminals
Less than 1 Ω
c
b
Using a Megger, test the insulation resistance between:
Primary winding and chassis
Pass if over 10 MΩ
Filament winding and chassis
Pass if over 10 MΩ
a
One end of the High Voltage winding is connected to the
chassis, so this is not tested.
2. High Voltage Capacitor Test
You will need:
A Digital Multi-meter (D.M.M.)
A Megger or similar resistance meter using 500V d.c.
WARNING: High voltages and large currents are present at the High Voltage Capacitor. It is very
dangerous to work near this part when the oven is on. NEVER make any voltage
measurements at the High Voltage circuits, including the magnetron filament.
WARNING: Even when the oven is not cooking, the High Voltage Capacitor has High Voltages
present because of the Soft Start circuit. Isolate the oven before testing.
See Safety Code ( Page 4 )
1. Isolate the oven from the mains supply.
2. Ensure that the High Voltage Capacitor is discharged before
commencing work.
3. Remove all connections from the High Voltage Capacitor.
4. Using a D.M.M., check for continuity between the terminals &
compare results with table on next page.
402s Ovens Pt. No. 32Z3522 Issue 6
23
PROCEDURES FOR PRINCIPAL COMPONENTS TEST (2)
( High Voltage Capacitor Test continued, ensure steps 1-4 on previous page have been completed)
Between Terminals
Pass if approximately 10 MΩ
Between Terminals and Case
Pass if open circuit
5. Using a Megger, test the insulation resistance between the
terminals and the case.
Between Terminals and Case
Pass if over 100 MΩ
3. High Voltage Rectifier Test
You will need:
A Megger or similar resistance meter using 500V d.c.
WARNING: High voltages and large currents are present at the High Voltage Capacitor. It is very
dangerous to work near this part when the oven is on. NEVER make any voltage
measurements at the High Voltage circuits, including the magnetron filament.
WARNING: Even when the oven is not cooking, the High Voltage Capacitor has High Voltages
present because of the Soft Start circuit. Isolate the oven before testing.
See Safety Code ( Page 4 )
1. Isolate the oven from the mains supply.
2. Ensure that the High Voltage Capacitor is
discharged before commencing work.
3. Remove all connections from the High Voltage
Rectifier.
4. Using the Megger, test for continuity in both
directions. Compare results with the table.
Open Circuit both ways
FAIL
Conducts one way only
PASS
Short Circuit both ways
FAIL
Conducts one way, leaks the other
FAIL
4. Magnetron Test
You will need:
A Megger or similar resistance meter using 500V d.c.
A Magnetron can be tested for an open filament or a short circuit
by carrying out a continuity check.
WARNING: High voltages and large currents are present at the High Voltage Capacitor. It is very
dangerous to work near this part when the oven is on. NEVER make any voltage
measurements at the High Voltage circuits, including the magnetron filament.
WARNING: Even when the oven is not cooking, the High Voltage Capacitor has High Voltages
present because of the Soft Start circuit. Isolate the oven before testing.
See Safety Code ( Page 4 )
1. Isolate the oven from the mains supply.
2. Ensure that the High Voltage Capacitor is discharged before
commencing work.
3. Remove all connections from the Magnetron.
4. A continuity check across the Filament terminals should be 1ohm or
less
5. A continuity check between each filament terminal and the
metal outer should read open.
402s Ovens Pt. No. 32Z3522 Issue 6
24
PROCEDURE FOR DOOR INTERLOCK ADJUSTMENT AND TEST 1
The door on the 402s oven is monitored by four microswitches. Three are used in the conventional
“Primary, Secondary and Monitor” switch arrangement shown below and the fourth sends a signal
to the Logic PCB. The switches operate as follows:
Door Interlock Arrangement: Switches shown in Door Closed position
LHS
RHS
L1
Power In
Primary
switch
Secondary
switch
Power
Out
Monitor
switch
Logic
PCB
L2
1. Monitor switch
The Monitor switch will produce a short circuit across the mains supply when the door
is opened if the Primary interlock switch is faulty, thus blowing the microwave fuse
and rendering the oven inoperative.
2. Primary Interlock and Secondary Interlock
The Primary switch will cut off the microwave emissions from the oven when the door
is opened by breaking the electrical supply circuit to the transformers. The Secondary
interlock switch will cut off the microwave emission if the Primary switch has failed.
Note:
If operation of the Monitor switch has caused the Microwave Fuse to blow, the
Primary and Monitor microswitches must be changed as they may have been
damaged by the high short-circuit currents involved.
Right Side
Monitor
SW1
Microswitches
RH side
Primary
SW2
Left Side
Door closed
Logic PCB
SW4
Secondary
SW3
402s Ovens Pt. No. 32Z3522 Issue 6
25
PROCEDURE FOR DOOR INTERLOCK ADJUSTMENT AND TEST 2
It is vital that the microswitches are adjusted to the correct position. There are two sets
switch assemblies located either side of the oven.
The interlocks ensure that the oven will not operate microwave with the door open.
WARNING
Before adjusting the microswitch
assemblies ensure that the oven
has been isolated from the
electrical supply.
Please note the terminals on the
microswitches remain live when
the oven is switched off, so
complete isolation is essential.
Objective
With a 1mm spacer located as shown, both
switches on both sides should be activated/ closed
position.
With a 5mm spacer located as shown SW2 and
SW3 should be open.
Method of adjustment.
By loosening the four screws on each mounting
bracket the microswitch assembly can be raised or
lowered and thereby the switches can be made to
operate at different door positions.
Procedure.
Spacer
1.
2.
Door seal
3.
4.
5.
6.
7.
8.
Isolate the oven from the Electrical supply.
Place a 1mm spacer between the cavity face
and the door seal as shown.
Working on the right hand side, adjust the
bracket so the SW2 ‘just’ operates.
Working on the left hand side, adjust the
bracket so that SW3 ‘just’ operates.
Remove the 1mm spacer and then place a
5mm spacer in the same position.
Check that SW2 and SW3 are open circuit and
not operated.
Repeat the steps above to ensure the setup is
correct.
Ensure that all the screws are tightened.
Reconnect the electrical supply.
402s Ovens Pt. No. 32Z3522 Issue 6
26
Door
PRINCIPAL COMPONENTS: Hot Air Motor & Controller 1
Convection and Fan Speed Control
The convection heat is provided by 5 elements located in the hot box at the rear of the oven
cavity. The hot air from the hot box passes over catalytic converters and is circulated into the
bottom and top of the cavity through the impinger plates. It returns through the removable grease
filter at the back of the cavity and into the fan.
Convection motor
The convection motor Is a 3-phase AC motor having a maximum speed of 7200 rpm controlled by
a motor speed controller.
The windings are thermally protected and in the event of a thermal fault a trip will operate and
shut down the motor speed controller.
Step
Motor/ controller fault finding
1
208V/240V, 60Hz Electrical supply into motor controller
2
Three phase connections to motor
3
Speed Controller connections to logic board
4
Motor thermal cut-out (short circuit)
5
Motor rotates freely/ not seized
6
Motor winding resistances:
Blue-Black 3 Ohms—4 Ohms
Black-Brown 3 Ohms—4 Ohms
Brown-Blue 3 Ohms—4 Ohms
Black or Brown or Blue to Earth (Open circuit)
No.
20
20
20A
23
Description
Part No.
DV0328
Heater Element 208V 650W 68Ω
Heater Element 240V 650W 88Ω
DV0337
Heater Element Collar
DV0058
Convection ( Hot Air ) Motor Assembly
SA208
Gasket Set
SA332
8x 31Z4016
M5 Flange nut
402s Ovens Pt. No. 32Z3522 Issue 6
27
PRINCIPAL COMPONENTS: Hot Air Motor & Controller 2
Motor Controller
Provides an AC, 3-phase switched mode drive to
the convection motor and is controlled by a 0 - 10
Volt signal from the logic board. This allows the
motor to be adjusted from approximately 1500
rpm to 7000 rpm in steps of 5%.
Door Open
Door Closed (not cooking)
Door Closed (cooking)
= 1500 RPM
= 3500 RPM
= as specified by
program or setting
Motor Speed and Logic board voltage table
Fan
speed %
Voltage
dc
RPM
Condition
100%
10V
7000
Full
Speed
50%
5V
3000
Door
Closed
20%
2V
1500
Door
Open
Power Terminals
Wire
27
Wire 26
Motor Terminals
Blue Black Brown
Blue 0V
V
Yellow 0-10V
Grey wire
to Motor
Red +10V
Displays and messages: LED status display
LED
Meaning
LED Off
Inverter Off / No supply
Long On & Off (1sec)
Power On / Ready
LED On steadily
Inverter Running
Long On (0.5 sec)/ short Off
General Warning
Position
LED
Very Short On & Off (0.1sec) Fault Condition
402s Ovens Pt. No. 32Z3522 Issue 6
28
CIRCUIT DIAGRAM: Issue 16
402s Ovens Pt. No. 32Z3522 Issue 6
29
Trouble-Shooting Guide
Is the problem Food Quality or Fundamental
Operational Issue?
Food Quality
Fundamental
Standard Food Quality Checks
Standard Electrical Checks
• Check that the PREHEAT temperature is
set correctly.
See User Manual.
• Check that the food being cooked has
been stored at the correct temperature.
• Check that the correct program is being
used.
• Check that oven is connected to an
Electricl Power supply and that any trip
that supplies the unit is not switched off.
• Check that the oven is switched on.
• Check the Electricl Power supply voltage
at the input terminal block.
• Check that all fuses are intact.
• Check that the overheat stat has not
tripped this can be checked by measuring
the voltage across the Auxiliary
transformer.
Still Have a problem:
Select a Category.
• Cold Food Page 32
Still Have a problem:
Select a Category.
• Core TemperaturesLow Page 32
• No Display Page 31
• Cavity Sensor Error Page 33
• Magnetron / Over heat errors Page 34
Note : The following Diagnosis procedures may not expose all possible errors but have
been included for general guidance.
402s Ovens Pt. No. 32Z3522 Issue 6
30
No Display
Is Logic PCB
Active ?
See D7 LED
OFF
OFF
ON
Is Relay PCB
Active see D27
ON
Check cable from logic PCB to
display is in place and no obvious
wires are disconnected or shorted.
Still Have a problem?
Check 15 Way Ribbon
Cable between
Logic and Relay PCB.
Still Have a Problem?
Using spare display
connect to Logic PCB
Still Dead
Spare Display
works
Replace
Display
Check Connection Output
at Aux Transformer.
Check Power supply to Relay PCB
Check Fuse on Relay PCB
Still Have a Problem?
Replace Logic PCB
402s Ovens Pt. No. 32Z3522 Issue 6
31
Cold Food
Check Convection
Temperature control
OK
NO
Possible Temperature Sensor Fault.
Assuming sensor Ok then make sure
door Light on logic PCB is on when
door closed. If this is working then
replace Logic PCB.
Check Current using clip on current
meter through F7 and F8. When
running Microwave only. You will
need to reset the pre-heat
temperature to 0 and enable manual
control via the profile setting. Make
sure that there is a water load in
the cavity.
Also, check that convection motor is
operational
More than
5 Amps
Less than
5 Amps
Check that the
stirrer is rotating.
Yes
Carry out Microwave Output Test
OK
LOW
Check Microwave Generating system
•
•
•
•
Transformer
Magnetron
Capacitor
Diode
32
Replace stirrer motor
and retest
Contact Merrychef Service
Department for Further
assistance.
402s Ovens Pt. No. 32Z3522 Issue 6
No
Cavity Sensor Error
Are there any Signs of
Cavity Fire
YES
Report to
Management and
Make Investigation
NO
Check Temperature
Sensor Resistance
OK
NOT
OK
Re-Start Oven
Activate Pre-heat
Is Led D19 on
relay PCB ON
Yes LED is on.
Check Heater
Elements
Replace if necessary
N
Check door Switch
LED on logic PCB
LED is on
Is the
temperature
display saying
too hot ?
N
Check the Door Interlock
Switch.
Check The interconnecting
lead to the logic PCB.
Cavity Sensor error is caused by one of the
following :1. The cavity did not heat by 180°F in the 10 Minutes
Assume the Cavity is
not too hot then:
Replace Sensor
2. The cavity exceeded the set point when cooking by
more than 72°F whilst cooking which indicates that
the food load was on fire
402s Ovens Pt. No. 32Z3522 Issue 6
33
Replace Sensor
Retest and calibrate
Oven.
Magnetron / Overheat issues
Remove and Clean Air Filters.
If Dirty—Advise operating staff of the need
for this to be carried out on regular basis.
See User Manual
Still have a problem.
Check Location of oven is away from any
major heat sources.
Recommend re-location if necessary
Location fine and still have a problem.
Check cooling fan operation. Make sure there is Noticeable airflow from
air vents at the rear of the oven.
If Not investigate and replace cooling fan if necessary.
Fan is fine and I still have a problem.
Magnetron
Error reported =
Magnetron or
Ambient
Note :- Each Magnetron
has a thermistor attached
to it. The control unit will
produce an error if the
temperature exceeds
235°F.
Establish if the magnetron
is actually getting hot.
Remember to take care
given the High Voltage in
the magnetron area.
Check sensor
connections.
Replace Magnetron.
Ambient
The Ambient Air Sensor is located on the
Relay PCB. Measure the temperature in
the area with all the case work in place
using a Thermocouple Meter
Less than 110°F
Check 15 ribbon Cable
Replace Relay PCB.
402s Ovens Pt. No. 32Z3522 Issue 6
34
Temperature
reading
More than
110°F
Cooling Air Flow
Problem into control
area.
Ambient Conditions
too hot
APPENDIX 1: TEMPERATURE SENSOR RESISTANCE DATA
Temperature Sensor Resistance
Temp °F
Temp °C
Min. Rate
kΩ
Standard
Rate kΩ
Max. Rate
kΩ
212
100
11.490
13.060
14.810
302
150
2.803
3.161
3.434
392
200
0.950
1.000
1.050
482
250
0.3572
0.3865
0.4171
R(200)°C = 1 kΩ ± 5%
Note:
These resistances will only be apparent in a stable cavity temperature as the
sensor has a slow response time.
402s Ovens Pt. No. 32Z3522 Issue 6
35
APPENDIX 2: MenuKey Version 2.0 models
The MenuKey System automatically changes all the cooking programs
on the oven from a pre-programmed electronic key.
Do not remove the key
during download sequence
as this could corrupt
the data on the key
To change the menus on the oven:
1 Ensure the power switch is OFF.
2 Lift the MenuKey cover in the
top front panel of the oven and
put the key in the slot.
MENUKEY2
3 With the key still in place switch
the power switch ON.
The oven will now go through the
program download sequence by
displaying the following:
The MenuKey Code.
4
e.g. 555
The MenuKey CS e.g.
0A06
MenuKey CS (checksum)
confirms the menus on this key
are valid for the MenuKey Code.
Confirm that the MenuKey Code
and MenuKey CS are correct
and press Download Function
key to load the programs into the
Oven memory.
Note: Downloading from a
MenuKey will clear all the
existing programs
MENUKEY2 DETECTED
MK CODE
555
MK CS 0A06
Download
Upload
Download
Download
The standby screen will then
display
Upload
WARNING
ALL OVEN PROGRAMS
WILL BE OVERWRITTEN
Exit
Continue
Check that the key is correct
then press the Continue
function key to proceed with the
Download
On completion of the download
press the Exit function key to
return the oven to standby mode.
The display briefly will show the
following:
Oven Model No. Software
& MenuKey serial No.
MENUKEY2 DETECTED
MK CODE
555
MK CS 0A06
MENUKEY2
DOWNLOADING
Continue
MENUKEY2
VERYIFYING
MENUKEY2 DOWNLOAD
COMPLETE
Exit
CHECKSUM:0A06
.
Model No. 402S
Software
MK serial No.
Remove the MenuKey and keep
in a safe place.
402s Ovens Part. No. 32Z3522 Issue 6
36
OVEN COLD
PRESS PREHEAT
Exit
APPENDIX 2: MenuKey Version 3.0 models
The MenuKey System automatically changes all the cooking programs
on the oven from a pre-programmed electronic key.
To change the menus on the oven:
WARNING
Downloading from a MenuKey will clear
all the existing programs
Do not remove the key
during download sequence
as this could corrupt
the data on the key
MENUKEY2
Check that the key has the correct
number/code for the programs you want
to load into the oven memory
1 Ensure the power switch is OFF.
2 Lift the MenuKey cover in the top front panel of
the oven and put the key in the slot.
3 With the key still in place switch the power switch ON.
The oven will now go through the program download
sequence by displaying the following:
Copying Programs from
MenuKey to Oven
MenuKey Detected
Please Wait
Verifying Programs
Copied Correctly
MenuKey Copied
Successfully
The display briefly will show the following : Oven Model No., Software & MenuKey serial No.
The Oven will then commence heating up to the PREHEAT temperature ready to cook.
4 Remove the MenuKey and keep in a safe place.
Saving Programs to a MenuKey
In the CATEGORIES screen select EDIT SCREEN ( Pad name hidden) then select CREATE MENUKEY
CAT 001
CAT 002
CAT 003
CAT 004
CATEGORIES
EDIT
CAT 005
CAT 006
CAT 007
CAT 008
EDIT CATEGORY NAME
EDIT A PROGRAM
CREATE MENUKEY
EDIT SCREEN
1 Enter a number for the MenuKey Code to identify
the new MenuKey, use the +/- Function Pads.
MENUKEY PROFILE
MenuKey Code: 000
Program Mode : ON
Temperature Scale : °C
Cooking Range: OFF
For an explanation of the following features see
Setting the Oven Profile Page 11
2
3
4
5
Cooking Range: OFF
Set the Program Mode to ON or OFF,
Set Manual Mode to ON or OFF:
Enter the Lower Band temperature setting 15-75°C
Set the oven Temperature Scale °C
Insert a MenuKey and press START to copy the programs.
The display shows the following:
Copying Programs from
Oven to MenuKey
Verifying Programs
Copied Correctly
START
WARNING
Any programs already
on the key will be deleted
MenuKey Copied
Successfully
The Display returns to the CATEGORIES screen and the Oven will heat up to the PREHEAT
temperature ready to cook.
402s Ovens Part. No. 32Z3522 Issue 6
37
APPENDIX 3: Cool Down Procedure
To cool down and clean a hot oven
Action
EC402s V2.0
EC 402s V3.0
COOL DOWN MODE
PLACE ICE IN CAVITY
COOL DOWN MODE
PLACE LOAD IN CAVITYAND
PRESS START
To commence Cool Down
procedure Press
Place Ice in cavity
Press
Continue
Start
The oven cools down for
approximately 30 minutes
Cycle ends
COOL DOWN MODE
OVEN HOT
PLEASE WAIT
( Also in Spanish)
COOL DOWN MODE
OVEN HOT
PLEASE WAIT
COOL DOWN COMPLETE
READY FOR CLEANING
Turn oven off and ensure
Air Filters are clean
Switch oven off ready for
cleaning
402s Ovens Pt. No. 32Z3522 Issue 6
38
APPENDIX 3: CLEANING: 1
For the oven to operate at peak efficiency, the cavity, door and air filters and grease filter must
be kept clean.
A daily cleaning routine will ensure that you comply with the required hygiene standards and will help
to maintain and prolong the efficiency of your oven.
Follow the SAFETY INSTRUCTIONS at the beginning of this manual.
WARNING: DO NOT use caustic cleaners on any part of the oven or oven
cavity as it will cause permanent damage to the Catalytic Convertors
• ALWAYS switch off at the electrical supply before
cleaning
• Complete COOL DOWN procedure and allow the
oven and accessories to cool before commencing
cleaning
Hot surface
Hazard
• As required wipe out spillages with disposable
paper wipes
• NEVER use steel wool, knives or harsh abrasives
on any part of the oven
As with all electrical appliances, it is wise to have the
electrical connections inspected periodically.
Faults arising from neglect or
misuse including use without clean
filters in place are not covered
by the guarantee. Service visits
as a result of such faults will be
chargeable.
DO NOT use the oven without clean air filters and cavity grease filter in place
START UP: OVEN COATING PROCEDURE ( clean, cold oven )
1.
With the oven clean and
cold, spray Merrychef
Oven Protector onto the
sponge
2.
Spread Oven Protector
lightly onto all internal
surfaces of the oven
3.
Spread Oven Protector
lightly onto the internal
surface of the oven door
Note: oven protector turns light brown when cured
402s Ovens Part. No. 32Z3522 Issue 6
39
4.
Switch the oven ON when
the oven has reached operating temperature it will
take 30 minutes to cure
the Oven Protector.
APPENDIX 3: CLEANING: 2
• ALWAYS switch off at the electrical supply and allow oven to cool before cleaning
• CAUTION: Allow the oven and accessories to cool before commencing cleaning
WARNING: DO NOT use caustic cleaners on any part of the oven or oven
cavity as it will cause permanent damage to the Catalytic Convertors
Equipment: Merrychef oven cleaner, Merrychef Oven Protector, heat proof gloves, protective rubber gloves,
non–abrasive nylon scrub pad, cleaning towel and cloths, eye protection and dust mask (optional)
COLD OVEN: CLEANING INSTRUCTIONS ( following cool down )
CAUTION: Wear protective rubber gloves when cleaning the oven
Oven Parts and filters
& Oven Cavity
Remove air filters
both sides
Wash all parts in warm soapy water. Wash off using a clean cloth and plenty of
clean, warm water. Dry using a fresh, clean cloth.
Remove the rack and lift
out bottom impinger plate
Remove top impinger plate
To remove grease filter
push down and lift out
Undo fasteners
If the door seals are damaged, the oven
must be repaired by an approved Servicer.
DO NOT spray directly into the fan opening at the rear of the oven
1.
Wear protective rubber
gloves and protective
glasses carefully spray
Merrychef Oven Cleaner
onto the internal surfaces
of the oven except door
seals.
DO NOT spray directly
into the fan opening at
the rear of the oven
2.
For difficult areas leave
to soak for 10 minutes.
Leave the oven door
open during cleaning.
Use a non–abrasive
nylon scrub pad/sponge
to clean all internal surfaces and the inside of
the door.
3.
Wash off using a clean
cloth and plenty of clean
warm water to rinse top,
sides and back of oven.
Dry using a fresh clean
cloth or paper towel.
Wipe the outside of the
oven with a damp cloth.
4.
Replace clean oven
parts
Grease Filter*
Top plate*
Bottom plate*
Air filters x2
DO NOT
USE TOOLS
*When replacing impinger plates and the cavity grease filter
use firm finger pressure to tighten fasteners
DO NOT USE TOOLS
DO NOT use the oven without clean
air filters and cavity grease filter in place
402s Ovens Part. No. 32Z3522 Issue 6
40
APPENDIX 4: Recommended spares lists
Part Number
Description
USA
Qty
Unit
First Aid
Kit
Service
Kit
1-5 Ovens
5-50
Ovens
50-100
Ovens
Piece Qty for 600
Ovens
2
11H0010
HT DIODE ASSY
2
EA
2
2
6
12
72
11K0002
LOGIC BOARD MAIN ASSY (V2 & V2.5)
1
EA
1
1
3
6
36
11K0004
MAI RELAY PCB
1
EA
1
1
3
6
36
11K0005
MENU KEY SOCKET ASSY
1
EA
1
3
6
36
11K0012
402s LD LOGIC PCB ASSY (V3)
1
EA
1
1
3
6
36
11K0013
402s FIBRE OPTIC BOARD ASSY
1
EA
1
1
3
6
36
11M0117
DC VOLTAGE CONNECTOR 10 WAY
1
EA
1
1
1
3
6
36
11M0367
VCK HT DIODE ASSEMBLY
2
EA
2
2
2
6
12
72
11Z0298
15 WAY 0.1 RIBBON CABLE ASSY
1
EA
1
1
1
3
6
36
30Z0217
FUSE 1in 10A HRC
5
EA
5
5
5
15
30
180
30Z0231
FUSE HOLDER 1IN (13A)
3
EA
3
3
3
9
18
108
30Z0235
GOLD RESISTOR (220R)
1
EA
1
1
3
6
36
30Z0957
FUSE 1x1/4in 1A HBC (MAINS)
1
EA
1
1
3
6
36
30Z1024
OVERHEAT SAFETY STAT
1
EA
1
1
3
6
36
30Z1155
BLOCK TRANSFORMER B0012024
1
EA
1
1
3
6
36
30Z1177
20 AMP LITTELFUSE FLM020
4
EA
4
4
4
12
24
144
30Z1178
30A FUSE HOLDER
4
EA
2
4
4
12
24
144
30Z1230
60HZ TRANS MULTI 208 220 240
2
EA
1
2
2
6
12
72
30Z1251
0.88uF 2500V CAPACITOR
2
EA
1
2
2
6
12
72
30Z1293
MOTOR SPEED CONTROLLER - US
1
EA
1
1
3
6
36
30Z1294
MICROSWITCH WITH ROLLER
2
EA
2
2
6
12
72
30Z1295
MAGNETRON COOLING FAN
1
EA
1
1
3
6
36
30Z1298
CAPACITOR - MOTOR START - 2uF
1
EA
1
1
3
6
36
30Z1299
DISPLAY ASSY + HEADER V2 - V2.5
1
EA
1
1
3
6
36
30Z1315
THERMISTOR 150MM + LEAD 900MM
1
EA
1
1
1
3
6
36
30Z1318
2 POLE ROUND ROCKER SWITCH
1
EA
1
1
1
3
6
36
30Z1324
DISPLAY ASSY + HEADER V3
1
EA
1
1
3
6
36
30Z1340
FILTER 16A SCREW MOUNT
2
EA
2
2
2
6
12
72
30Z1349
MAGNETRON 2M248H-B
2
EA
2
2
2
6
12
72
30Z1375
CRYDON SOLID STATE RELAY
1
EA
2
6
12
72
31Z0186
DOOR SEAL SEALANT - 1 TUBE
1
TUBE
2
6
12
72
31Z0477
4 WAY MAINS TERMINAL BLOCK
1
EA
2
6
12
72
31Z0499
CABLE GLAND NUT
1
EA
2
6
12
72
31Z0500
CABLE GLAND LARGE
1
EA
2
6
12
72
31Z0527
STIRRER COVER - SEALANT 1 TUBE
1
TUBE
1
1
2
6
12
72
31Z1247
MICROSWITCH SPRING INTERLOCK
1
EA
1
1
1
3
6
36
32Z1066
DOOR HANDLE
1
EA
1
3
6
36
DV0037
BOTTOM TRIM
1
EA
1
1
2
12
DV0052
MENUKEY DUST COVER
1
EA
1
3
6
36
DV0055
MEMBRANE PANEL - V2 - 2.5
1
EA
1
3
6
36
DV0091
SIDE PANEL L/H
1
EA
1
1
2
12
DV0092
SIDE PANEL RH
1
EA
1
1
2
12
DV0094
TOP TRIM - V1
1
EA
1
1
2
12
DV0168
DOOR CHOKE (PRESSED)
1
EA
1
3
6
36
DV0187
TOP PANEL (PRESSED)
1
EA
1
3
6
36
DV0192
WAWA MEMBRANE
1
EA
1
1
3
6
36
DV0203
SEAL - CERAMIC COVER
2
EA
2
2
6
12
72
DV0254
402s MEMBRANE V3
1
EA
1
1
3
6
36
DV0275
RACK V3
1
EA
1
3
6
36
DV0305
DOOR SEAL 402S
1
EA
2
6
12
72
1
2
1
2
1
1
1
402s Ovens Pt. No. 32Z3522 Issue 6
41
APPENDIX 4: Recommended spares lists
Part Number
Description
USA CONT.
Qty
Unit
First Aid
Kit
Service
Kit
1-5 Ovens
5-50
Ovens
50-100
Ovens
Piece Qty for 600
Ovens
DV0328
HEATER ELT 208V 650W WATLOW
5
EA
5
5
5
15
30
180
DV0337
HEATER ELT 240V 650W WATLOW
5
EA
5
5
5
15
30
180
DV0492
STIRRER COVER - CERAMIC
2
EA
2
2
2
6
12
72
DV0501
DOOR SKIN
1
EA
1
3
6
36
DV0504
DOOR CHOKE V1
1
EA
1
3
6
36
SA104
DOOR ASSEMBLY V1
1
EA
1
1
2
12
SA111
DOOR ASSEMBLY V2 - V3
1
EA
1
3
6
36
SA183
402s HOT AIR MOTOR SERVICE KIT
1
EA
1
3
6
36
SA202
DOOR HINGE ASSEMBLY RH
1
EA
1
3
6
36
SA203
DOOR HINGE ASSEMBLY LH
1
EA
1
3
6
36
SA211
IMPINGER PLATE UPPER ASSY
1
EA
1
3
6
36
SA212
M/SWITCH BRACKET ASSY
2
EA
2
6
12
72
SA213
STIRRER ASSEMBLY
2
EA
2
6
12
72
SA217
MAINS LEAD ASSY (US)
1
EA
1
1
2
4
24
SA234
THERMISTOR SENSOR 50K NTC
2
EA
2
2
6
12
72
SA250
402s GREASE FILTER UPGRADE KIT
1
EA
1
3
6
36
SA251
402s CERAMIC COVER UPGRADE KIT
1
EA
1
3
6
36
SA252
TOOL KIT FOR SA251
1
EA
1
3
6
36
SA253
402s IMPINGER UPGRADE KIT
1
EA
1
3
6
36
SA254
402s WHISTLE STOP UPGRADE KIT
1
EA
1
3
6
36
SA257
EC402s SOUNDER ASSY
1
EA
1
3
6
36
SA266
IMPINGER PLATE LOWER ASSY
1
EA
1
3
6
36
SA276
AIR FILTER ASSY
2
EA
2
2
6
12
72
SA288
STIRRER MOTOR ASSY (PINNED)
1
EA
1
1
3
6
36
SA311
IMPELLER - HOT AIR MOTOR
1
EA
1
3
6
36
SA314
CATALYST ASSY UPPER (V1 - V2.5)
1
EA
1
1
2
12
SA315
CATALYST ASSY LOWER V1 - V2.5)
1
EA
1
1
2
12
SA329
REAR PANEL
1
EA
1
1
2
12
SA332
GASKET SET
1
EA
1
3
6
36
SA339
GREASE FILTER HOUSING
1
EA
1
1
2
12
SA340
GREASE FILTER CARTRIDGE
1
EA
1
2
4
24
SA351
CATALYST ASSY UPPER (V3)
1
EA
1
1
2
12
SA353
CATALYST ASSY LOWER (V3)
1
EA
1
1
2
12
1
2
2
1
402s Ovens Pt. No. 32Z3522 Issue 6
42
APPENDIX 5: LOGIC PCB Connection Points and key features.
Spare input
not used
Display
Connecter
Temp Calibration
Relay PCB 15 way
Connecter
Door
Switch IP
Door switch
Indicator
ON when door
closed
Remote data
point
MenuKey
Sockect
Connector
Program
memory storage.
May be
exchanged
with New PCB if
PCB replaced.
Motor speed
controller
Membrane panel
connector
402s Ovens Pt. No. 32Z3522 Issue 6
43
D7 Power LED
Indicates Logic PCB
is powered
See Troubleshooting
Guide
APPENDIX 5: Relay PCB Connection Points and key features.
D15 Magnetron
active
Cavity
Temperature
Sensor
Input
D16 Magnetron
soft start
D19 Heater ON
Magentron
Overheat sensor
Inputs
D20 LED
ON
when power is on
OFF
when Microwave is
operated.
Connector To
Logic PCB
U1 Ambient air
temperature
sensor
Display
Fuse
Fuse
Not Used
AC input from
Aux Transformer
Piezo sounder
output
402s Ovens Pt. No. 32Z3522 Issue 6
44
APPENDIX 6: Engineering Test Settings
Engineering Test Settings - Changing the Oven Profile
In order to carry out an oven test procedure the oven PREHEAT must be set to 0ºF/OFF to
switch off the convection heaters and the Manual controls must be enabled.
When the test is completed the oven must be returned to its original settings or the
appropriate MenuKey can be used to reset the oven automatically.
To set the PREHEAT temperature to 0ºF/OFF
402s Version 3.0 models
402s Version 2.0/ 2.5
1. Switch the oven OFF
2. Switch ON and immediately press Edit Preheat
Temp.
1. Switch the oven OFF
2. Switch ON and
immediately press
Edit Preheat to show
the ENTER
PREHEAT TEMP
screen.
3. Make a note of the Preheat temperature in the
display.
merrychef
Edit Preheat
Profile
3. Make a note of the Preheat temperature in
the display.
4. Press 0, 0, 0 to overwrite the current
temperature setting.
Then press Save to
store this setting
ENTER PREHEAT TEMP
000ºF
Save
Press +>> for OFF
( note pressing either +>> or << - will cycle
through all the available temperatures)
Then Press Save to store this setting
To set the Oven controls to allow Manual operation
1. Switch the oven OFF then
2. Switch ON and immediately press the lower right
pad to display the OVEN PROFILE screen.
3. Press to set Manual Mode to ON Then Press Save
1. Switch the oven OFF
2. Switch ON and
immediately press
Profile to edit the oven
operating profile
3. Press Change to set
OVEN MODE to
PROGRAM/MANUAL
merrychef
Change
Profile
OVEN MODE
PROGRAM/MANUAL
Change
Next
Then press Next five times to return
to the OVEN COLD standby screen.
To use MANUAL MODE:
from the OVEN COLD/PRESS PREHEAT
standby screen press the PREHEAT/
COOL DOWN pad on the control panel
and then press Manual.
To use Manual Mode: from the CATEGORIES
standby screen press the lower centre right pad
To display the Manual mode screen.
READY
TO COOK AT 000ºF
Manual
402s Ovens Pt. No. 32Z3522 Issue 6
45
Run Prog
APPENDIX 7: Firmware revision guide.
As a result of on-going changes / upgrades to the 402s Oven, this Appendix has been produced
stating the following:
1.0 An overview of the control system for a 402s.
2.0 How to check your Firmware version
3.0 How to check your hardware fitted
4.0 CODEKEY firmware upgrade
5.0 MenuKey2 download
CODEKEY Reference ( See Table 1 for abbreviations description)
Version 3
Part No. 31Z7066 3.0LD 402s Large Display UK/EU (FO / EMD)
Part No. 31Z7068 3.0LD 402s Large Display French (FO / EMD)
Part No. 31Z7071 4.3LD 402s Large Display UK/EU (FO / SSR / EMD)
Part No. 31Z7072 4.3LD 402s Large Display French (FO / SSR / EMD)
Part No. 31Z7073 4.4LD 402s Large Display US/EU
(FO / SSR / EMD / NSS / NPM / NEPT / NEP)
For QSR restaurants
Version 2.5
Part No.
31Z7067
4.4SD 402s Small Display UK/EU (FO / EMD)
1.0 The 402s Control System
The control system of the 402s is based upon the following fundamentals:
Logic PCB:
Controls and monitors all aspects of the oven and stores all Firmware and Menu Data.
Convection Fan
Fibre Optic Expansion
Menus:
This is where all of the
Information for menus is
stored. It can be changed
manually or by a MenuKey
Firmware:
This is where all of the oven
operating instructions are
stored. It can be changed
by a CODEKEY
LOGIC PCB
Door Sensor
Solid State Relay
Microswitches
Relay PCB:
Driven by the Logic PCB the Relay PCB
controls all of the power around the oven.
Heater Elements
Magnetrons
Sensors
402s Ovens Pt. No. 32Z3522 Issue 6
46
2.0 How to check your Firmware Version:
2.1
Power up the oven and verify the Firmware version that is loaded into the oven.
OVEN INFORMATION
Oven On Time:
Magnetron On Time:
Door Operations:
Software Version:
MenuKey Code:
MenuKey Checksum
00028 Hours
00000 Hours
00049
4.1LD
002
F076
PAUSE>>
Check the Software Version on the Oven Start Up screen and refer to Table 1 below
Firmware Verification: Table 1
Firmware Version for 402s V3 ovens
Abbreviation Firmware Features
Code
Supported
NSS
NEPT
NEP
NPM
FO
2.8LD
or lower
3.0LD
4.0LD 4.1LD
4.2LD
4.3LD 4.4LD
GM
QSR
Screen Saver
No Screen Saver
Edit Pre-Heat
Hidden Edit Pre-Heat
Edit Profile
Hidden Edit Profile
Edit Programs
Hidden Edit Programs
*
Magnetron Detect
EMD
Extended Mag Detect
SSR
Solid State Relay
Note: this Table excludes KFC France ovens.
*IIf Fibre Optic hardware is fitted.
Please also be aware of the store you are visiting as this would dictate what version of Firmware
they would require. See below for clarification.
CODEKEY Version 4.3LD or lower (GM ovens)
CODEKEY Version 4.4LD (QSR ovens)
All ovens except ‘Quick Service Restaurants'’
Subway and KFC
‘Quick Service Restaurants’ only including
Subway and KFC
Note: ALL ovens that are lower than 3.0LD Firmware should be up-lifted to version
3.0LD or higher depending on what hardware is fitted. (Refer to Table 2a & Table 2b)
402s Ovens Pt. No. 32Z3522 Issue 6
47
3.0 How to check your hardware fitted:
3.1
Remove the oven lid to reveal the Logic PCB. See Table 2a below
Hardware fitted
against PCB visual
TABLE 2A
SSR
PCB Visual Check
Supports
Oven
Upgrade
to V3
Mag
Detect
Allowable
Version /
Firmware
Revision 1
ONLY ON
V2 ovens
4.4SD
Device
secured to
plate
No pin strip
ON V2.5
ovens
4.4SD
or higher
Revision 2
Device
free
standing
ON V3
Ovens
3.0LD
or higher
Pin strip fitted but no optics board
TABLE 2B Hardware Upgrade
Technical Bulletin
Required
V2
oven
V2.5
oven
V3
oven
Adding Magnetron Detect
TB114
TB114
Adding Solid State Relay
TB122
TB122
Hardware Upgrade
402s Ovens Pt. No. 32Z3522 Issue 6
48
Hardware fitted
against PCB visual
TABLE 2A
SSR
PCB Visual Check
Supports
Oven
Upgrade
to V3
Mag
Detect
Blue jumper
fitted
Allowable
Version /
Firmware
ON V2.5
ovens
4.4SD
Revision 3
ON V3
ovens
3.0LD
or higher
Optics
board fitted
SSR lead
SSR would be
fitted if lead is
present on PCB
ONLY ON
V3
ovens
3.0LD
or higher
Fibre Optics Board + leads fitted
TABLE 2b: Hardware Upgrade
Technical Bulletin
Required
V2
oven
V2.5
oven
V3
oven
Adding Magnetron Detect
TB114
TB114
Adding Solid State Relay
TB122
TB122
Hardware Upgrade
402s Ovens Pt. No. 32Z3522 Issue 6
49
4.0 CODEKEY Firmware upgrade
Procedure:
Before commencing an oven Firmware upgrade ensure the oven is switched off
4.1 Insert the appropriate CODEKEY (see Matrix 01 on page 2) into the Menukey receptacle on the
control panel.
Lift cover to insert CodeKey into
Menukey receptacle.
Oven power switch
4.2
Warning:
During the next step the display will be blank for approximately 1 minute.
DO NOT REMOVE THE CODEKEY/ DO NOT TURN THE OVEN OFF
this will damage the logic board.
Switch the oven ON to activate the CodeKey, the screen
will remain blank for approximately 1 minute before the
startup screen displays.
After I minute the Oven will boot-up immediately press the
PAUSE pad to hold the oven information screen.
OVEN INFORMATION
Oven On Time:
Magnetron On Time:
Door Operations:
Software Version:
MenuKey Code:
MenuKey Checksum
00028 Hours
00000 Hours
00049
4.0LD
002
F076
PAUSE>>
PAUSE pad
402s Ovens Pt. No. 32Z3522 Issue 6
50
4.3 To confirm a successful download check that the Software Version on
the oven and the CODEKEY fob Label are the same.
OVEN INFORMATION
Oven On Time:
Magnetron On Time:
Door Operations:
Software Version:
MenuKey Code:
MenuKey Checksum
00028 Hours
00000 Hours
00049
4.3LD
002
F076
EXIT>>
Software Version
CODEKEY
Fob
Label
Software: 4.3LD
Date:
00/00/07
CS:
0x9C71
4.4 Press exit and remove and retain the CODEKEY.
5.0 MenuKey2 download
Procedure:
Before commencing a MenuKey download ensure the oven is switched OFF
1.
2.
3.
Insert the appropriate MenuKey into the control panel
socket.
Switch the Oven ON
[DO NOT REMOVE the MenuKey as this will corrupt the
data on the key]
The display will show the following:
MenuKey Detected
Please Wait
4.
5.
Copying Programs from
MenuKey to Oven
Verifying Programs
Copied successfully
MenuKey Copied
Successfully
The display will show the start up sequence and the Oven will begin heating up.
Remove the MENUKEY
402s Ovens Pt. No. 32Z3522 Issue 6
51