Download COM SIKOSTART 3RW22 - Service, Support
Transcript
COM SIKOSTART 3RW22 Betriebsanleitung Instructions Bestell-Nr./ Order-Nr. GWA 4NEB 535 0464-10a Ausgabe / Edition 10/95 COM SIKOSTART 3RW22 3RW2701-0AA0 Betriebsanleitung HardwareVoraussetzungen Deutsch Welche Hardware ist erforderlich? 7 IBM-AT kompatibler Rechner 7 erforderlicher freier Arbeitsspeicher: min. 540 kB 7 Schnittstellenbaustein: xx86450 (oder kompatibel) 7 Schnittstellenleitung 3RW2920-1DA00 oder Leitung gemäß Betriebsanleitung 3ZX1012-0RW22 Nicht erforderlich sind: 7 Maus wird nicht unterstützt 7 Co-Prozessor beschleunigt den Programmablauf 7 EMS beschleunigt den Programmablauf Folgende Einstellungen erfolgen automatisch: 7 Bildschirm: wird automatisch erkannt. Falls Probleme auftreten, setzen Sie bei Hercules-, VGA/EGAoder Plasma-Bildschirmen den Hintergrund vor Programmstart auf Schwarz. 7 SHIFT-, NUM LOCK- und SCROLL-Tasten: Das Programm belegt die Tasten mit den erforderlichen Funktionen und setzt sie nach Verlassen des Programms wieder in den ursprünglichen Zustand. 7 Port-Leitungen: Die Zustände der Leitungen werden zu Programmstart gelesen und nach Verlassen des Programms wiederhergestellt. SoftwareVoraussetzungen Welche Software ist erforderlich? 7 Mindestens MS-DOS oder PC-DOS ab Version 3.xx. 1 Installation Beachten Sie bei der Installation die folgenden Punkte: 7 Beenden Sie alle laufenden Anwendungen, bevor Sie das Programm starten. 7 Starten Sie das Programm nicht unter WINDOWS (als DOS-Applikation). 7 Starten Sie das Programm immer nur von der Festplatte, nicht von der Diskette. Das Programm muß auf die Festplatte installiert werden. Es ist in gepackter Form (3RW22COM.EXE) auf der Diskette gespeichert. Während der Installation entpackt es sich selbst auf die Festplatte. Die Installation auf Diskette oder der Start von Diskette ist nicht möglich: Sie zerstören dabei die Daten auf der Diskette. Ab Version 4.00 ist das Programm nicht mehr kopiergeschützt. Installation: Befehle So installieren Sie das Programm: 1. Stecken Sie die Diskette in das Laufwerk. 2. Wählen Sie das Laufwerk an durch Eingabe von: A: < ↵ > bzw. B: < ↵ > 3. INSTALL A: C: \name< ↵ > Sprachen Die eingestellte Sprache können Sie durch Eingabe von SPRACHE2 ändern. 2 Änderungen Änderungen finden Sie in der Datei README2.DEU: 7 Geben Sie ein: TYPE README2.DEU ¦ MORE < ↵> Ermitteln des seriellen Ports So ermitteln Sie den seriellen Port: 1. Schließen Sie das Schnittstellenkabel an den freien seriellen Port an. 2. Verbinden Sie PIN 2 und PIN 3 des Steckers (z. B. mit einem Schraubendreher). 3. Geben Sie SERTEST < ↵ > ein und warten Sie am Bildschirm die Meldungen ab. ➨ Der belegte Port muß blinken. Merken Sie sich die Nummer des Ports. 4. Entfernen Sie die Verbindung zwischen PIN 2 und PIN 3 und stecken Sie das Kabel auf den Schnittstellenstecker des 3RW22. 5. Legen Sie den Starter an die Versorgungsspannung: ➨ Die oberste LED (Betriebsbereit) muß leuchten. Programmstart Geben Sie folgende Befehle ein: 6. Starten Sie das Programm durch Eingabe von RW22PC < ↵ >, bzw. RW22PC L< ↵ > bei monochromem Monitor. 7. Wählen Sie im Hauptmenü Punkt 1 (Konfiguration) an. 8. Gehen Sie in der Maske mit dem Cursor auf die Nummer des belegten Ports (➨ Punkt 3) und drücken Sie < ↵ >. 9. Drücken Sie <F2> zum Sichern der Einstellung. 10. Drücken Sie <ESC> zur Rückkehr in das Hauptmenü. 11. Kontrollieren Sie die Einstellung am Bildschirm. Achtung Die Steuer-Befehle START, STOPP und RESET (QUITT) dürfen nur vom PC oder nur von der Anlagensteuerung gegeben werden. Anderenfalls ist die Betriebssicherheit nicht gewährleistet. 3 Testsoftware Computer-Viren Die mitgelieferte Testsoftware behebt Probleme bei der Installation: 7 KARTE überprüft die vom Programm erkannten VIDEO-Konfigurationen 7 FREE_MEM überprüft den noch freien Arbeitsspeicher und die TSR-Programme (=speicherresidente Programme) 7 SERTEST überprüft die seriellen Schnittstellen Die Dateien auf der Diskette sind nach den McAfee Ass. bekannten Computer-Viren garantiert virenfrei. Hinweis: Wenn Sie den SIKOSTART 3RW22 ohne angeschlossenen Motor und Steuerverdrahtung parametrieren möchten, müssen sie die Klemme 9 und 11 brücken. 4 Betrieb mit verschiedenen Parametern Nach Auswahl der Funktion ”Parametrieren” im Hauptmenü müssen Sie in folgender Maske wählen, ob Sie 1, 2 oder 3 Motoren parametrieren wollen. Je nach Wahl haben die Steuereingänge IN 1, IN 2 und IN 3 unterschiedliche Funktion. (C) Siemens AG COM SIKOSTART - V xxx1 Einstellung des SIKOSTART 3RW22 für Standard Anwendung Polumschaltbare Motoren Dahlander Motoren Serielles Anlassen Serielles Anlassen ein Parametersatz zwei Parametersätze drei Parametersätze Zugehörige Funktion der Eingänge 1, 2 und 3: IN 1: EIN IN 2: AUS IN 3: RESET IN 1: EIN/AUS Parametersatz 1 IN 2: EIN/AUS Parametersatz 2 IN 3: RESET IN 1: EIN/AUS Parametersatz 1 IN 2: EIN/AUS Parametersatz 2 IN 3: EIN/AUS Parametersatz 3 1. entspricht der Versionsnummer: z.B. 3.0 oder 3.01 Die Funktion der Steuereingänge ist in dieser Einstellung wie in der Betriebsanleitung 3ZX10120RW22 beschrieben. In diesen Einstellungen hat jeder Steuereingang eine EIN/AUS Funktion, d.h., wenn der Kontakt zwischen OUT L+ DC 24 V (Klemme 11) und dem entsprechenden Eingang geschlossen ist, wird mit zugehörigem Parametersatz gestartet; bei Öffnen des Kontaktes schaltet SIKOSTART wieder ab. Werden mehr als ein Steuereingang betätigt, schaltet SIKOSTART ab. Bei Betrieb mit drei Parametersätzen ist die Quittierung einer Störung nur über den PC (F9) oder durch Abschalten der Versorgungsspannung möglich. HINWEIS: Verwenden Sie das entsprechende beiliegende Klebeschild zur richtigen Kennzeichnung der Steuereingänge. 5 Sanftanlauf von polumschaltbaren Motoren mit getrennten Wicklungen für zwei unterschiedliche Parametersätze Sie benötigen dazu eine SIKOSTART mit PC-Kommunikation. Beachten Sie die zuverlässigen Werte für Anlaufstrom und Anlaufzeit von SIKOSTART und Motor bei der Projektierung. 3/N/PE ~50Hz 230/400 V L1 L2 L3 N PE F6 F1 G1: SIKOSTART 3RW22 F1: Motorabzweigsicherungen F3: Halbleitersicherungen F6: Steuerspannungssicherung F7: Überlastrelais 1. Drehzahl F8: Überlastrelais 2. Drehzahl S1 K1: Netzschütz K5: Schütz 1. Drehzahl K6: Schütz 2. Drehzahl S1: Not-Aus-Einrichtung S2: Aus-Taster S5: Störung quittieren S7: Ein 1. Drehzahl S8: Ein 2. Drehzahl M1: Motor S5 K6 K1 F3 G1 15 14 13 12 11 K5 S2 F7 F8 S8 S7 L1 L2 L3 AC 380-415 V AC 200-240 V AC 100-120 V N/L. DC L+ 24 V 10 IN 1 9 IN 2 8 Reset 7 6 Störung 5 4 Anlauf3 ende 2 Brems1 schütz T1 T2 T3 S7 K5 K6 S8 K6 K5 S7 S8 K1 K5 K6 F7 K5 N K6 K1 F8 2W 2V 2U M 3~ M1 6 1W 1V 1U F12 K8 K30 K30 Ansprechverzögerung K10, K20, K30 ca. 200 ms K30 K20 K22 K10 N K22 K9 K32 K10 K8 S31 K22 K12 K20 F32 K12 K12 K9 S21 S30 K20 K10 F22 S20 K30 K20 K8 S11 S10 K32 K8 S1 L1 L2 L3 N PE K10 K9 K32 K20 G1: SIKOSTART 3RW22 F1: Motorabzweigsicherungen F3: Halbleitersicherungen F5: Steuerspannungssicherung F6: Steuerspannungssicherung F11, F21, F31: Motorabzweigsicherungen F12, F22, F32: Überlastrelais K1: Netzschütz K8: Hilfsschütz Störung K9: Hilfsschütz Anlauf-Ende K10, K20, K30: Motorschütz K12, K22, K32: Motorschütz S1: Not-Aus-Einrichtung S5: Störung quittieren S10, S20, S30: Aus-Taster S11, S21, S31: Ein-Taster M1: Motor F5 K9 S5 F6 K10 1 2 3 4 6 5 7 8 10 9 11 Störung K1 K10 BremsSchütz AnlaufEnde K20 K30 IN 3 IN 2 IN 1 L1 L2 L3 T1 T2 T3 M1 F12 K12 K1 F3 F11 F1 G1 15 AC 380-415V 14 AC 200-240V 13 AC 100-120V 12 N/L . DC L+ 24V 3/N/PE~ 50 Hz 230/400 V M 3~ U V W K20 M2 F22 K22 F21 M 3~ U V W K30 M3 F32 K32 F31 M 3~ U V W Sanftanlauf für serielles Anlassen von 3 Motoren mit 3 Parametersätzen Sie benötigen dazu einen SIKOSTART mit PC-Schnittstelle. Beachten Sie die zulässigen Werte für Anlaufstrom und Anlaufzeit von SIKOSTART und Motor bei der Projektierung. 7 COM SIKOSTART 3RW22 3RW2701-0AA0 Instructions Hardware requirements English What is the hardware requirement? 7 IBM-AT-compatible computer 7 Free space in the RAM: min. 540 kB 7 Interface module: xx86450 (or compatible) 7 Interface cable 3RW2920-1DA00 or cable according to Instructions 3ZX1012-0RW22 Not required: 7 Mouse Not supported 7 Co-processor Accelerates program execution 7 EMS Accelerates program execution The following settings take place automatically: 7 Display: Automatic In the case of Hercules, VGA/EGA or plasma displays: if problems occur, set the background to black before the program starts. 7 SHIFT, NUMLOCK und SCROLL keys: The program assigns the necessary functions to the keys and resets them again to their original status after the program is exited. 7 Port cables: The statuses of the cables are read at the start of the program and are restored when the program is executed. Software requirements 8 What is the software requirement? 7 Minimum MS-DOS or PC-DOS version 3.xx or higher Installation Please note the following points concerning installation: 7 Terminate all applications in progress before starting the program. 7 Do not start the program under WINDOWS (as DOS application). 7 Only start the program from the hard disk, not from the floppy disk. The program must be installed on the hard disk. It is stored on the floppy disk in compressed form (3RW22COM.EXE). During installation, it decompresses itself onto the hard disk. Installation on floppy disk or start from floppy disk is not possible: The data on the floppy disk will be destroyed. From version 4.00 the program is not protected against copying any more. Installation: Commands The program is installed as follows: 1. Insert the floppy disk in the drive. 2. Select the drive by entering: A: < ↵ > or B: < ↵ > 3. INSTALL A: C: \name< ↵ > Languages The selected language can be changed by entering SPRACHE2. 9 New versions You will find new versions in the file README2.ENG: 7 Enter: TYPE README2.ENG ¦ MORE < ↵> Location of the serial port The serial port is located as follows: 1. Connect the interface cable to the free serial port. 2. Connect PIN 2 and PIN 3 of the connector (e.g. using a screwdriver). 3.Enter SERTEST < ↵ > and wait for the messages on the screen. ➨ The assigned port must flash. Note the number of the port. 4. Remove the connection between PIN 2 and PIN 3 and plug the cable onto the interface connector of the 3RW22. 5. Connect the starter to the power supply: ➨ The top LED (Ready) must light up. Program start Enter the following commands: 6. Start the program by entering RW22PC < ↵ >,or RW22PC L< ↵ > for the monochrome monitor. 7. Select item 1 (configuration) of the main menu. 8. Using the cursor, move to the number of the assigned port (➨ item 3) and press < ↵ >. 9. Press <F2> to save the setting. 10. Press <ESC> to return to the main menu. 11.Check the setting on the display. Caution The control commands START, STOP and RESET (QUIT) may only be given by the PC or the system controller. Otherwise there is no assurance of operating safety. 10 Test software Computer viruses The test software supplied eliminates problems occurring on installation: 7 KARTE Checks the VIDEO configurations detected by the program 7 FREE_ MEM Checks the free memory and the TSR programs (=resident programs) 7 SERTEST Checks the serial interfaces The files on the diskette are guaranteed free of viruses according to the viruses known according to McAfee Ass. Note: If you wish to assign parameters to the SIKOSTART 3RW22 without a motor connected and without control wiring, you must bridge terminals 9 and 11. 11 Operation with different parameters After selecting the "parameter setting" function from the main menu, you must select whether you wish to set the parameters for 1, 2 or 3 motors in the following screen form. Depending on the selection you have made, control inputs IN 1, IN 2 and IN 3 have different functions. (C) Siemens AG COM SIKOSTART - V xxx1 Setting the SIKOSTART 3RW22 for Standard application Pole changing motors Dahlander motors Cascade starting Cascade starting One parameter set Two parameter sets Three parameter sets Function of the inputs 1, 2 and 3 in each case: IN 1: ON IN 2: OFF IN 3: RESET IN 1: ON/OFF Parameter set 1 IN2 ON/OFF Parameter set 2 IN 3: RESET IN 1: ON/OFF Parameter set 1 IN 2: ON/OFF Parameter set 2 IN 3: ON/OFF Parameter set 3 1. Corresponds to the Version No., e.g. 3.0 or 3.01 The function of the control inputs in this setting is as described in the 3ZX1012-0RW22 manual In these settings, every input has an ON/OFF function, i. e. if the contact between OUT L+ DC 24 V (terminal 11) and the corresponding input is closed, starting is performed with the appropriate parameter set; when the contact is opened, SIKOSTART switches off again. If more than one control input is used SIKOSTART switches itself off. If used with three parameter sets, it is only possible to acknowledge a fault via the PC (F9) or by switching off the power supply. NOTE: Use the correct label (enclosed) for the control inputs. 12 Soft starting of pole-changing motors with separate windings for two different parameter sets To do this you require a SIKOSTART with PC communication. Pay attention at the planning stage to the permissible starting-current and starting-time values of the SIKOSTART and the motor. 3/N/PE ~50Hz 230/400 V G1: SIKOSTART 3RW22 F1: Motor circuit fuses F3: Semiconductor fuses F6: Control voltage fuse F7: Overload relay, 1st speed L1 L2 L3 N PE F6 F8: Overload relay, 2nd speed K1: Line contactor K5: Contactor, 1st speed K6: Contactor, 2nd speed S1: EMERGENCY OFF device S2: OFF button S5: Acknowledge fault S7: ON, 1st speed S8: ON, 2nd speed M1: Motor F1 K1 S1 F3 G1 15 14 13 12 11 K5 K6 S5 S2 F7 F8 S8 S7 L1 L2 L3 AC 380-415 V AC 200-240 V AC 100-120 V N/L. DC L+ 24 V 10 IN 1 9 IN 2 8 Reset 7 6 Fault 5 4 End of 3 starting 2 Breaking 1 contactor T1 T2 T3 S7 K5 K6 S8 K6 K5 S7 S8 K1 K6 K5 F8 F7 K5 N K6 K1 2W 2V 2U M 3~ 1W 1V 1U M1 13 14 F12 K8 K30 K30 Response delay K10, K20, K30 approx. 200 ms K30 K20 K22 K10 N K22 K9 K32 K10 K8 K22 K12 S31 F32 K12 K12 K9 K20 S30 K20 K10 S21 F22 S20 K30 K20 K8 S11 S10 G1: SIKOSTART 3RW22 F1: Motor branch circuit fuses F3: Semiconductor fuses F5: Control voltage fuses F6: Control voltage fuses F11, F21, F31: Motor branch circuit fuses F12, F22, F32: Overload relay K1: Mains contactor K8: Auxiliary contactor fault K9: Auxiliary contactor end of starting K10, K20, K30: Motor contactor K12, K22, K32: Motor contactor S1: Emergency off device S5: Acknowledge fault S10, S20, S30: Off pushbutton S11, S21, S31: On pushbutton M1: Motor K10 K32 K9 K32 K20 K8 S1 L1 L2 L3 N PE F5 K9 S5 F6 5 6 K10 1 2 4 3 Fault K1 K10 Breaking contactor End of starting K20 K30 L1 L2 L3 T1 T2 T3 M1 F12 K12 K1 F3 F11 F1 G1 15 AC 380-415V 14 AC 200-240V 13 AC 100-120V 12 N/L . 11 DC L+ 24V 10 IN 1 9 IN 2 8 IN 3 7 3/N/PE~ 50 Hz 230/400 V M 3~ U V W K20 M2 F22 K22 F21 M 3~ U V W K30 M3 F32 K32 F31 M 3~ U V W Soft cascade starting of three motors with three parameter sets To do this you require a SIKOSTART with PC communication. Observe the permissible values for starting current and starting time of the SIKOSTART and the motor in your planning. COM SIKOSTART 3RW22 3RW2701-0AA0 Instrucciones de servicio Requerimientos hardware Español ¿Qué hardware se necesita? 7 Computador compatible IBM-AT 7 Memoria RAM libre necesaria: mín. 540 kB 7 Chip de comunicaciones: xx86450 (o compatible) 7 Cable de comunicación 3RW2920-1DA00 o cable según instrucciones 3ZX1012-0RW22 No se precisa: 7 Ratón no es soportado 7 Coprocesador acelera la ejecución del programa 7 EMS acelera la ejecución del programa Automáticamente se ajusta lo siguiente: 7 Pantalla: es reconocida automáticamente Si aparecen problemas, en caso de pantallas con controlador Hercules, VGA/EGA o tipo plasma, poner negro el fondo antes de comenzar el programa. 7 Teclas SHIFT, NUM LOCK y SCROLL: El programa asigna a dichas teclas las funciones correspondientes; al finalizar el programa vuelven a asignarse sus funciones primitivas. 7 Líneas de port: Al arrancar el programa se leen los estados de las líneas; al abandonarlo vuelve a restablecerse el estado primitivo. Requerimientos software ¿Qué software se necesita? 7 Como mínimo MS-DOS o PC-DOS a partir de la version 3.xx. 15 Instalación Al instalar es preciso observar los puntos siguientes: 7 Antes de arrancar el programa es preciso abandonar todas las aplicaciones en curso. 7 No arrancar el programa bajo WINDOWS (como aplicación DOS). 7 Arrancar el programa siempre desde el disco duro, no desde el disquete. El programa debe estar instalado en el disco duro. Tiene como nombre 3RW22COM y está comprimido en el disquete. Durante la instalación se descomprime automáticamente y se graba en el disco duro. No es posible instalarlo en un disquete o arrancarlo desde éste: al hacerlo se destruyen los datos contenidos en el disquete. A partir de la version 4.00 el programa se encuentra sin proteccion para copiado. Comandos de instalación: Forma de instalar el programa: 1. Insertar el disquete en la unidad. 2. Seleccionar la unidad correspondiente: A: < ↵ > o B: < ↵ > 3. INSTALL A: C: \nombre< ↵ > Idiomas Tecleando SPRACHE2 es posible modificar el idioma ajustado. 16 Cambios de versión Los cambios de versión figuran en el fichero README2.SPA: 7 Teclear: TYPE README2.SPA ¦ MORE < ↵> Localización del port serie Forma de localizar el port serie: 1. Conectar el cable de comunicación en el port serie libre. 2. Unir los PINES 2 y 3 del conector (p. ej. con un destornillador). 3. Teclear SERTEST < ↵ > y esperar los mensajes que aparecen en pantalla. ➨ deberá quedar intermitente el port ocupado. Anote el número del port. 4. Quitar la conexión entre los PINES 2 y 3 y conectar el cable en el conector de comunicación (interfase) del 3RW22. 5. Aplicar tensión de alimentación al arrancador: ➨ deberá lucir el LED superior (señaliza ”listo”). Arranque del programa Forma de proceder: 6. Arrancar el programa tecleando RW22PC <↵ >, o RW22PC L< ↵ > en caso de monitor monocromo. 7. Dentro del menú principal, elegir el punto 1 (configuración). 8. Llevar el cursor sobre el número del port ocupado ( ➨ punto 3) y pulsar < ↵ >. 9. Pulsar <F2> para salvaguardar los ajustes efectuados. 10. Pulsar <ESC> para retornar al menú principal. 11. Controlar el ajuste en pantalla. Atención Las órdenes START (MARCHA), STOPP (PARADA) y RESET (QUITT) solo deberán darse desde el PC o desde el equipo de control de la instalación. De lo contrario no queda garantizada la seguridad de funcionamiento. 17 Software de test Virus El software de test suministrado resuelve problemas durante la instalación: 7 KARTE verifica las configuraciones de VIDEO conocidas por el programa 7 FREE_MEM verifica el espacio aún libre en memoria y los programas TSR (=programa residente de memoria) 7 SERTEST verifica las interfases serie (ports) En los ficheros del disquete se garantiza la ausencia de virus de computador conocidos según McAfee Ass. Nota Si se desea parametrizar el SIKOSTART 3RW22 sin que esté conectado ni el motor ni el cableado de mando, entonces es necesario unir por un puente los bornes 9 y 11. 18 Funcionamiento con diferentes parámetros Una vez seleccionada la función "Parametrización" (ajuste de parámetros) en el menú básico es preciso seleccionar en la máscara siguiente si se desean parametrizar 1, 2 ó 3 motores. Dependiendo de dicha elección tienen diferente función las entradas de mando IN 1, IN 2 e IN3. (C) Siemens AG COM SIKOSTART - V xxx1 Parametrización del SIKOSTART 3RW22 para Aplicación estandar Motores de 2 bobinados Motores Dahlander Arranque en cascada Arranque en cascada un juego de parámetros dos juegos de parámetros tres juegos de parámetros Función correspondiente de las entradas 1, 2 y 3: IN 1: MARCHA IN 2: PARADA IN 3: RESET IN 1: MARCHA/ PARADA juego de parám.1 IN2 MARCHA/ PARADA juego de parám. 2 IN 3: RESET IN 1: MARCHA/ PARADA juego de parám. 1 IN 2: MARCHA/ PARADA juego de parám. 2 IN 3: MARCHA/ PARADA juego de parám. 3 1. se corresponde con el número de versión: p. ej. 3.0 ó 3.01 Para el caso de la figura, la función de las entradas de mando es idéntica a la descrita en las instrucciones 3ZX1012-0RW22 En estos dos casos, cada entrada tiene una función MARCHA/PARADA, es decir, cuando se cierre el contacto entre OUT DC L+ 24 V (borne 11) y una de las entradas, el arranque se realiza con el juego de parámetros correspondiente a dicha entrada. La apertura del contacto pone fuera de circuito el SIKOSTART. Si se activa mas de una entrada control se desconecta el SIKOSTART. Cuando se opera con tres juegos de parámetros, el acuse de un fallo solo puede realizarse desde el PC (F9) o cortando la tensión de alimentación. INDICACION: Utilice las etiquetas que se adjuntan para marcar correctamente las entradas de mando. 19 Arranque suave de motores de polos conmutables con devanado separado para dos juegos de parámetros diferentes Para ello se precisa un SIKOSTART que pueda comunicarse con un PC. Al diseñar, observar los valores admisibles para la intensidad y el tiempo de arranque tanto para el SIKOSTART como para el motor. 3/N/PE ~50Hz 230/400 V L1 L2 L3 N PE F6 G1: SIKOSTART 3RW22 F1: Fusibles derivación a motor F3: Fusibles para semiconductores F6: Fusible circuito de mando F1 F7: Relé de sobrecarga 1a veloc. F8: Relé de sobrecarga 2a veloc. S1 K1: Contactor de red K5: Contact. 1a veloc. K6: Contact. 2a veloc. S1: Disp. parada emerg. S2: Pulsador DES S5: Acuse de perturb. S7: Con 1a veloc. S5 K6 S8: Con 2a veloc. M1: Motor K1 F3 G1 15 14 13 12 11 K5 S2 F7 F8 S8 S7 L1 L2 L3 AC 380-415 V AC 200-240 V AC 100-120 V N/L. DC L+ 24 V 10 9 IN 1 IN 2 8 Reset 7 6 Fallo 5 4 Fin 3 arranque 2 Contact 1 frenado T1 T2 T3 S7 K5 K6 S8 K6 K5 S7 S8 K1 K6 K5 F8 F7 K5 N K6 K1 2W 2V 2U M 3~ M1 20 1W 1V 1U F12 K30 K30 K32 K8 S1 L1 L2 L3 N PE K10 K9 K32 K20 Retardo de respuesta de K10, K20, K30: aprox. 200 ms K30 K20 K8 K10 N K22 K32 K22 K9 K22 K10 K8 S31 F32 K12 K12 K9 K12 K20 S30 K20 K10 S21 F22 S20 K30 K20 K8 S11 S10 G1: SIKOSTART 3RW22 F1: Fusibles de salida al motor F3: Fusibles para tiristores F5: Fusible p. tensión mando F6: Fusible p. tensión mando F11, F21, F31: Fusibles salida motor F12, F22, F32: Relé de sobrecarga K1: Contactor de red K8: Contactor aux. fallo K9: Contactor aux. fin arranque K10, K20, K30: Contactor motor K12, K22, K32: Contactor motor S1: Parada de emergencia S5: Acuse de fallo S10, S20, S30: Pulsador PARADA S11, S21, S31: Pulsador MARCHA M1: Motor F5 K9 S5 F6 K10 1 2 4 3 5 6 K1 K10 Contact. frenado Fin arranque Fallo K20 K30 L1 L2 L3 T1 T2 T3 M1 F12 K12 K1 F3 F11 F1 G1 15 AC 380-415V 14 AC 200-240V 13 AC 100-120V 12 N/L . 11 DC L+ 24V 10 IN 1 9 IN 2 8 IN 3 7 3/N/PE~ 50 Hz 230/400 V M 3~ U V W K20 M2 F22 K22 F21 M 3~ U V W K30 M3 F32 K32 F31 M 3~ U V W Arranque suave en cascada de 3 motores con 3 juegos de parámetros Para ello se precisa un SIKOSTART que pueda comunicarse con un PC. Durante la parametrización considerar los valores admisibles para la corriente y la duración de arranque, tanto para el SIKOSTART como para el motor. 21 COM SIKOSTART 3RW22 3RW2701-0AA0 Instructions Matériel requis Français Quelle est la configuration matérielle nécessaire ? 7 ordinateur compatible IBM AT 7 espace libre nécessaire en mémoire vive : min. 540 KB 7 circuit interface : xx86450 (ou compatible) 7 câble d'interface 3RW2920-1DA00 ou câble conforme aux instructions 3ZX1012-0RW22 Ne sont pas nécessaire : 7 souris n'est pas supportée 7 coprozessor accélère l'exécution du programme 7 EMS accélère l'exécution du programme Les réglages suivants sont automatiques : 7 écran : est identifié automatiquement S'il y a des problèmes en liaison avec un écran Hercules, VGA/EGA ou plasma, réglez un fond noir avant de lancer le programme. 7 Touches SHIFT, NUM LOCK et SCROLL : Le programme affecte à ces touches certaines fonctions propres et rétablit l'affectation initiale au moment de quitter le programme. 7 Lignes de port : Les états des lignes sont lus lors du démarrage du programme et restaurés lorsqu'on le quitte. Logiciel requis Que faut-il comme logiciel ? 7 au moins le MS-DOS ou PC-DOS de version ≥ 3.xx. 22 Installation Points à respecter lors de l'installation : 7 Terminez toutes les applications en cours avant de lancer le programme. 7 Ne lancer pas le programme sous WINDOWS (en tant qu'application DOS). 7 Lancez toujours le programme à partir du disque dur et non pas depuis la disquette. Le programme doit être installé sur le disque dur. Le programme (3RW22COM.EXE) est sous forme comprimée sur la disquette. Durant l'installation, il se décomprime de lui-même sur le disque dur. Une installation sur disquette ou le lancement depuis la disquette ne sont pas possibles: cela se traduirait par une destruction des fichiers sur la disquette. A partir de la version 4.00 le programme n’est plus protégé contre la copie. Installation : Commandes Marche à suivre pour installer le programme : 1. Introduisez la disquette dans le lecteur. 2. Sélectionnez le lecteur comme le lecteur courant en tapant : A: < ↵ > ou B: < ↵ > 3. INSTALL A: C: \nom< ↵ > Langues Vous pouvez changer la langue des textes d'écran en tapant SPRACHE2. 23 Modifications Les modifications sont décrites dans le fichier README2.FRA : 7 tapez : TYPE README2.FRA ¦ MORE < ↵> Identification du port séri Procédure d'identification du port série : 1. Brancher le câble d'interface sur le port série libre. 2. Ponter les broches PIN 2 et PIN 3 du connecteur (par exemple avec un tournevis). 3. Tapez SERTEST < ↵ > et attendez l'affichage du message sur l'écran. ➨ Le port occupé doit clignoter. Notez bien le numéro du port. 4. Supprimer le pontage entre PIN 2 et PIN 3 et enficher le câble sur le connecteur d'interface du démarreur 3RW22. 5. Mettez le démarreur sous tension : ➨ la LED supérieure (prêt) doit s'allumer. Lancement du programme Entrez les commandes suivantes : 6. Lancez le programme en tapant RW22PC < ↵ >, ou RW22PC L< ↵ > si votre moniteur est monochrome. 7. Sélectionnez le point 1 (Configuration) dans le menu de base. 8. Dans le masque, pointez avec le curseur le numéro du port occupé (cf. point 3) et appuyez sur < ↵ >. 9. Appuyez sur <F2> pour sauvegarder vos réglages. 10. Appuyez sur <ESC> pour revenir au menu de base. 11. Contrôlez les réglages à l'écran. Attention Les ordres START, STOPP et RESET (QUITT) ne doivent être transmis que depuis l'ordinateur ou depuis la commande de l'installation. Sinon la sécurité de service est compromise. 24 Logiciel de test Virus Le logiciel de test joint sert au moment de l'installation : 7 KARTE vérifie les configurations VIDEO reconnues par le programme 7 FREE_MEM vérifie la place libre en mémoire vive ainsi que les programmes TSR (= résidents en mémoire) 7 SERTEST vérifie les interfaces série Les fichiers sur la disquette sont garantis exempts de virus connus selon McAfee Ass. Remarque: Si vous voulez paramétrer le SIKOSTART 3RW22 sans qu’il soit raccordé à un moteur et cans câblage de commande, il faut shunter les bornes 9 et 11. 25 Fonctionnement avec différents paramètres Après sélection de la fonction "Paramétrage" dans le menu de base, il faut que vous choisisez dans le masque suivant si vous désirez paramétrer 1, 2 ou 3 moteurs. Suivant votre choix, les entrées de commande IN 1, IN 2 et IN 3 auront des fonctions différentes. (C) Siemens AG COM SIKOSTART - V xxx1 Paramétrage du SIKOSTART 3RW22 pour Application standard Moteurs à 2 bobinages Moteurs Dahlander Démarrage en cascade Démarrage en cascade un jeux de paramètres deux jeux de paramètres trois jeux de paramètres Fonction correspondante des entrées 1, 2 et 3: IN 1: MARCHE IN 2: ARRET IN 3: RESET IN 1: MARCHE/ ARRET jeux de param. 1 IN2 MARCHE/ ARRET jeux de param. 2 IN 3: RESET IN 1: MARCHE/ ARRET jeux de param. 1 IN 2: MARCHE/ ARRET jeux de param. 2 IN 3: MARCHE/ ARRET jeux de param. 3 1. numéro de version, par exemple 3.0 ou 3.01 Pour ce cas de figure, la fonction des entrées de commande est identique à celle décrite aux instructions 3ZX1012-0RW22 26 Dans ces deux cas, chaque entrée a une fonction MARCHE/ARRET, c.-à-d. que lorsque le contact entre OUT DC L+ 24 V (borne 11) e l’une des entrées est fermé, le démarrage s’effectue avec le jeu de paramètres correspondant à cette entrée. L’ ouverture du contact remet le SIKOSTART hors circuit. L’activation simultanée de plusiers entrée de commande entraîne la coupure du SIKOSTART. Los de l’utilisation de trois jeux de paramètres, l’aquittement d’un défaut ne peut se faire que par le PC (F9) ou en coupant la tension d’alimentation. REMARQUE: Parmi les étiquettes jointes, choisissez la bonne pour repérer les entrées de commande. Démarrage progressif de moteurs à deux vitesses à deux bobinages pour deux jeux de paramètres différents Il vous faut un SIKOSTART pouvant communiquer avec un PC. Tenez compte dans le choix de la configuration des valeurs admissibles pour le courant et le temps de démarrage de SIKOSTART et du moteur. 3/N/PE ~50Hz 230/400 V L1 L2 L3 G1: SIKOSTART 3RW22 N F1: Fusibles du départ moteur PE F6 F3: Fusibles des semiconducteurs F6: Fusible tension de commande F7: Relais de surcharge vitesse 1 F8: Relais de surcharge vitesse 2 K1: Contacteur principal K5: Contacteur vitesse 1 S1 K6: Contacteur vitesse 2 S1: Arrêt d'urgence S2: Bouton d'arrêt S5: Acquittement défaut S7: Marche vitesse 1 S8: Marche vitesse 2 M1: Moteur S5 F1 K1 F3 G1 15 14 13 12 11 K5 K6 S2 F7 F8 S8 S7 L1 L2 L3 AC 380- 415 V AC 200- 240 V AC 100- 120 V N/L. DC L+ 24 V 9 IN 1 IN 2 8 Reset 7 6 Défaut 5 4 Fin dé3 marrage 2 Contact. 1 freinage 10 T1 T2 T3 S7 K5 K6 S8 K6 K5 S7 S8 K1 K5 K6 F7 K5 N K6 K1 F8 2W 2V 2U M 3~ 1W 1V 1U M1 27 28 F12 K8 K30 K30 Retard de résponse de K10, K20, K30: 200 ms env. K30 K20 K22 K10 N K22 K9 K32 K10 K8 K22 K12 S31 F32 K12 K12 K9 K20 S30 K20 K10 S21 F22 S20 K30 K20 K8 S11 S10 G1: SIKOSTART 3RW22 F1: Fusibles de départ moteur F3: Fusibles des thyristors F5: Fusibles p. tension de cde F6: Fusibles p. tension de cde F11, F21, F31: Fusibles de surcharge F12, F22, F32: Relais de surcharge K1: Contacteur réseau K8: Contacteur aux. défaut K9: Contacteur aux. fin démarrage K10, K20, K30: Contacteur moteur K12, K22, K32: Contacteur moteur S1: Arrêt d'urgence S5: Acquittement défaut S10, S20, S30: Boutons arrêt S11, S21, S31: Boutons marche M1: Moteur K10 K32 K9 K32 K20 K8 S1 L1 L2 L3 N PE F5 K9 S5 F6 K10 1 2 4 3 5 6 K1 K10 Contact. freinage Fin démarrage Défaut K20 K30 L1 L2 L3 T1 T2 T3 M1 F12 K12 K1 F3 F11 F1 G1 15 AC 380-415V 14 AC 200-240V 13 AC 100-120V 12 N/L . 11 DC L+ 24V 10 IN 1 9 IN 2 8 IN 3 7 3/N/PE~ 50 Hz 230/400 V M 3~ U V W K20 M2 F22 K22 F21 M 3~ U V W K30 M3 F32 K32 F31 M 3~ U V W Démarrage progressif en cascade de 3 moteurs avec 3 jeux de paramètres Il vous faut un SIKOSTART pouvant communiquer avec un PC. Lors du paramétrage, tenez compte des valeurs admises pour le courant et la durée de démarrage, pour le SIKOSTART et le moteur. COM SIKOSTART 3RW22 3RW2701-0AA0 Instruzioni d’uso Premesse hardware Italiano Quali premesse hardware sono necessarie? 7 Calcolatore compatibile IBM-AT 7 Memoria di lavoro libera necessaria: min. 540 kB 7 Scheda interfaccia: xx86450 (o compatibili) 7 Conduttore interfaccia 3RW2920-1DA00 oppure conduttore sec. istruzioni d'uso 3ZX1012-0RW22 Non sono necessari: 7 Mouse non è previsto 7 Coprocessore accelera lo svolgimento del programma 7 EMS accelera lo svolgimento del programma Le seguenti impostazioni sono automatiche: 7 Schermo: viene riconosciuto automaticamente. In caso di difficoltà, per schermi Hercules, VGA/EGA o plasma commutare prima dello start del programma commutare lo sfondo su nero. 7 Tasti SHIFT, NUM LOCK, SCROLL: Il programma assegna ai tasti le funzioni necessarie; dopo l'abbandono del programma riporta i tasti allo originale. 7 Conduttori Port: All'inizio del programma vengono letti gli stati dei conduttori e dopo l'abbandono del programma vengono riportati allo statooriginale. Premesse software Quali premesse software sono necessarie? 7 lmeno MS-DOS o PC-DOS dalla versione 3.xx. 29 Installazione Per l'installazione tenere conto di quanto segue: 7 Terminare tutte le operazioni in corso prima di iniziare il programma. 7 Non iniziare il programma in WINDOWS (come applicazione DOS). 7 Iniziare il programma sempre solo dal disco fisso, non dal dischetto. Il programma deve essere installato sul disco fisso. Il programma 3RW22COM.EXE si trova in formato compresso sul dischetto e deve essere installato sul disco fisso. Durante l'installazione il programma si decomprime automaticamente. Non sono possibili l'installazione e lo start direttamente dal dischetto, altrimenti vengono distrutti tutti i dati del dischetto. Dalla versione 4.00 programme mon piu protetto. Installazione: Comandi Così si installa il programma: 1. Inserire il dischetto nel drive. 2. Selezionare il drive impostando: A: < ↵ > opp. B: < ↵ > 3. INSTALL A: C: \nome< ↵ > Lingue Per cambiare la lingua impostata impostare SPRACHE2. 30 Modifica della versione Modifiche della versione sono contenute nel file README2.ITA: Ricerca del Port seriale Il Port seriale viene trovato nel modo seguente: 1. Allacciare il cavo dell'interfaccia al Port seriale libero. 2. Collegare PIN 2 e PIN 3 del connettore (per es. con un cacciavite). 3. Impostare SERTEST < ↵ > e attendere la segnalazione. ➨ il Port occupato deve lampeggiare. Tenere a mente il numero del Port. 4. Scollegare PIN 2 e PIN 3 e inserire il cavo nel connettore per l'interfaccia del 3RW22. 5. Collegare lo starter alla tensione di alimentazione: ➨ Il LED superiore deve essere acceso (pronto al funzionamento). Start del programma Impostare i seguenti comandi: 6. Avviare il programma impostando RW22PC < ↵ >oppure RW22PC L< ↵ > su monitor monocromatico. 7. Selezionare nel menu principale il punto 1 (configurazione). 8. Nella maschera posizionare il cursore sul numero del Port occupato (punto 3) e selezionare < ↵ >. 9. Azionare <F2> per salvare l'impostazione. 10. Azionare <ESC> per ritornare al menu principale. 11. Controllare le impostazioni sullo schermo. 7 Impostare: TYPE README2.ITA ¦ MORE < ↵> Attenzione Gli ordini START, STOP e RESET (QUITT) possono essere emessi solo dal PC oppure solo dal controllo dell'impianto. In caso contrario non viene più garantita la sicurezza operativa. 31 Software di prova Virus Il software di prova che viene fornito aiuta a risolvere problemi che sorgono al momento dell'installazione: 7 KARTE controlla le configurazioni VIDEO riconosciute dal programma 7 FREE_MEM controlla la memoria di lavoro ancora libera e i programmi TSR (=programmi residenti in memoria). 7 SERTEST controlla le interfacce seriali Viene garantito che i file contenuti nel dischetto sono privi di virus, sec. McAfee Ass. Avvertenza: Se desiderate parametrizzare il SIKOSTART 3RW22 prima di collegare il motore e di aver eseguito il cablaggio, è necessario ponticellare i morsetti 9 e 11. 32 Esercizio con parametri diversi Dopo aver selezionato la funzione "Memorizzazione" nel menu principale, nella seguente maschera bisogna scegliere se si vuole parametrizzare 1, 2 o 3 motori. A seconda della scelta, gli ingressi di comando IN 1, IN 2 e IN 3 hanno funzioni differenti. (C) Siemens AG COM SIKOSTART - V xxx1 Impostazione del SIKOSTART 3RW22 per Applicazioni standard Motori a poli conmutabili Motori Dahlander Avviamento seriale Avviamento seriale un blocco di parametri due blocci di parametri tre blocchi di param. Funzioni relative agli ingressi 1, 2 e3: IN 1: ON IN 2: OFF IN 3: RESET IN 1: ON/OFF Blocco parametri 1 IN2 ON/OFF Blocco parametri 2 IN 3: RESET IN 1: ON/OFF Blocco parametri 1 IN 2: ON/OFF Blocco parametri 2 IN 3: ON/OFF Blocco parametri 3 1. corrisponde al numero di esecuzione; per es. 3.0 oppure 3.01 La funzione degli ingressi di comando è impostata come descritto nel manuale 3ZX10120RW22 In queste impostazioni ogni ingresso ha una funzione ON/OFF; ciò significa che, se il contatto fra OUT L+ 24 V DC (morsetto 11) e il relativo ingresso è chiuso, lo start avviene mediante il blocco di parametri corrispondente; quando il contatto apre, il SIKOSTART disinserisce. Se venpona azionati pió de un ingresso de comando si disinserice automaticamente. Se vengono usati tre blocchi di parametri, eventuali errori possono essere tacitati solo da PC (F9) o disinserendo la tensione di alimentazione. Avviso: Per definire correttamente gli ingressi, utilizzare la targhetta adesiva allegata. 33 Avviamento dolce di motori a poli commutabili con avvolgimenti separati per due blocchi di parametri diversi Per poter fare questo è necessario un SIKOSTART con communicazione PC. Al momento della progettazione fare attenzione ai valori ammessi per la corrente di avviamento e per il tempo di avviamento di SIKOSTART e del motore. 3/N/PE ~50Hz 230/400 V L1 L2 L3 N PE G1: SIKOSTART 3RW22 F6 F1: Fusibili derivazione motore F3: Fusibili semiconduttori F6: Fusibile della tensione di comando F7: Relè di sovraccarico, 1a velocità F8: Relè di sovraccarico, 2a velocità K1: Contattore di rete F1 K1 S1 K5: Contattore, 1a velocità K6: Contattore, 2a velocità S1: Dispositivo per Off di emergenza S2: Pulsante di Off S5: Tacitazione guasto S7: On, 1a velocità S8: On, 2a velocità K6 S5 M1: Motore F3 G1 15 14 13 12 11 K5 S2 F7 F8 S8 S7 L1 L2 L3 AC 380-415 V AC 200-240 V AC 100-120 V N/L. DC L+ 24 V 10 IN 1 9 IN 2 8 Reset 7 6 Errore 5 4 Fine 3 avviam. 2 Contat1 tore frenat. T1 T2 T3 S7 K5 K6 S8 K6 K5 S7 S8 K1 K6 K5 F8 F7 K5 N K6 K1 2W 2V 2U M 3~ M1 34 1W 1V 1U F12 K30 K30 Ritardo all'eccitazione K10, K20, K30 ca. 200 ms K30 K20 K8 K10 N K22 K32 K22 K9 S31 K22 K10 K8 K20 F32 K12 K12 K9 K12 S21 S30 K20 K10 F22 S20 K30 K20 K8 S11 S10 K32 K8 S1 K10 K9 K32 K20 G1: SIKOSTART 3RW22 F1: Fusibili di derivazione motore F3: Fusibili dei semiconduttori F5: Fusibile tensione di comando F6: Fusibile tensione di comando F11, F21, F31: Fusibili di derivazione motore F12, F22, F32: Relè di sovraccarico K1: Contattore rete K8: Errore al contattore ausiliario K9: Fine avviamento del contattore ausialiario K10, K20, K30: Contattore del motore K12, K22, K32: Contattore del motore S1: Dispositivo OFF d'emergenza S5: Tacitare l'errore S10, S20, S30: Tasto OFF S11, S21, S31: Tasto ON M1: Motore L1 L2 L3 N PE F5 K9 S5 F6 K10 1 2 4 3 5 6 7 8 10 9 11 Errore K1 K10 Fine avviam. Contattore frenat. K20 K30 IN 3 IN 1 IN 2 DC L+ 24V L1 L2 L3 T1 T2 T3 M1 F12 K12 K1 F3 F11 F1 G1 15 AC 380-415V 14 AC 200-240V 13 AC 100-120V 12 N/L . 3/N/PE~ 50 Hz 230/400 V M 3~ U V W K20 M2 F22 K22 F21 M 3~ U V W K30 M3 F32 K32 F31 M 3~ U V W Avviamento dolce per avviamento seriale di 3 motori con 3 blocchi di parametri Per poter fare questo è necessario un SIKOSTART con communicazione PC. In fase di progettazione tenere conto dei valori ammessi per la corrente all’avviamento e il tempo di avviamento. 35 COM SIKOSTART 3RW22 3RW2701-0AA0 Driftsinstruktion Förutsättningar för maskinvaran Svenska Vilken maskinvara behövs? 7 IBM-AT eller kompatibel PC 7 Ledigt arbetsminne: min. 540 KB 7 Gränssnittsenhet: xx86450 (eller kompatibel) 7 Gränssnittledning 3RW2920-1DA00 eller ledning enl. driftsinstruktion 3ZX1012-0RW22 Erfordras ej: 7 Mus understöds ej 7 Co-processor accelererar programkörningen 7 EMS accelererar programkörningen Följande inställningar görs automatiskt: 7 Bildskärmen: uppfattas automatiskt Om problem förekommer, ställ in svart bakgrund på bildskärmar typ Hercules, VGA/EGA eller Plasma. 7 Tangenterna SHIFT, NUM LOCK och SCROLL: Programmet belägger tangenterna med erforderliga funktioner och återställer ursprungstillståndet när programmet avslutats. 7 Port-ledningar: Ledningarnas tillstånd avläses vid programstarten och återställs vid slutet av programmet. Förutsättningar för programvaran 36 Vilken programvara erfordras? 7 Minst MS-DOS eller PC-DOS f.o.m. version 3.xx. Installation Ge akt på följande punkter vid installationen: 7 Avsluta alla pågående tillämpningar innan programmet startas. 7 Starta ej programmet under WINDOWS (som DOS-tillämpning). 7 Starta alltid programmet från hårddisken, ej från disketten. Programmet måste installeras på hårddisken. Programmet är lagrat i packad form pä diskett(3RW22COM.EXE). Vid installationen packas det automatiskt upp på hårddisken. Installation på diskett eller start från diskett går ej: Försök att göra detta förstör data på disketten. From version 4.00 är imte programment skydat för kopiering. Installation: Kommandon Så installeras programmet: 1. Stick in disketten i diskettstationen. 2. Ange diskettstationen genom att skriva: A: < ↵ > resp. B: < ↵ > 3. INSTALL A: C: \namn< ↵ > Språk Man kan ändra det inställda språket genom att ange SPRACHE2. 37 Versionsändringar Versionsändringar beskrivs i filen README2.SWE: 7 Skriv: TYPE README2.SWE ¦ MORE < ↵> Identifikation av seriell port Så här fastställs den seriella porten: 1. Anslut gränssnittkabeln till den lediga seriella porten. 2. Koppla samman PIN 1 och PIN 3 på stiftdonet. 3. Skriv SERTEST< ↵ > e och vänta tills meddelandena tills meddelandena visas på bildskärmen. ➨ Den belagda porten måste blinka. Anteckna portens nummer. 4. Ta bort förbindelsen mellan PIN 2 och PIN 3 och sätt kabeln på gränssnittkontakten på 3RW22. 5. Slå på strömmen till startkopplaren: ➨ den översta lysdioden (driftklar) måste vara tänd. Programstart Skriv följande kommandon: 6. Starta programmet genom att skriva RW22PC < ↵ >, resp. RW22PC L< ↵ > för en svartvit monitor. 7. Välj Punkt 1 (konfigurering) i huvudmenyn. 8. Gå med markören till den belagda portens nummer (➨ punkt 3) och tryck < ↵ >. 9. Tryck <F2> för att bekräfta inställningen. 10. Tryck <ESC> för att återvända till huvudmenyn. 11. Kontrollera inställningen på bildskärmen. Observera Styrkommandona START, STOPP och RESET (QUITT) får bara ges från PC eller av systemstyrningen. I annan fall kan driftsäkerheten inte garanteras. 38 Testprogram Datorvirus De medföljande testprogrammen åtgärdar problem vid installationen: 7 KARTE kontrollerar de VIDEO-konfigurationer som programmet känner igen 7 FREE_MEM kontrollerar ledigt arbetsminne och TSR-program (fast lagrade program) 7 SERTEST kontrollerar de seriella gränssnitten Filerna på disketten är garantera virusfria enl. McAfee Ass.. OBS: Om parametrar för SIKOSTART 3RW22 skall sättas utan ansluten motor och utan uppkopplade manöverledningar, så måste klämmorna 9 och 11 byglas. 39 Drift med olika parametrar När du vlat funktionen "Parametrar" i huvudmenyn måste du välja om du vill sätta parametrar för 1, 2 eller 3 motorer. Beroende på valet har styringångarna IN 1, IN 2, IN 3 olikes function. (C) Siemens AG COM SIKOSTART - V xxx1 Inställning av SIKOSTART 3RW22 för Standardanvändning Polomkopplingsbara mot. Dahlandermotorer Seriell start Seriell start en parameterpost två parameterposter tre parameterposter Tillhörande funktion på ingångarna 1, 2 och 3: IN 1: TILL IN 2: FRÅN IN 3: RESET IN 1 TILL/FRÅN Parameterpost 1 IN 2: TILL/FRÅN Parameterpost 2 IN 3 RESET IN 1: TILL/FRÅN Parameterpost 1 IN 2: TILL/FRÅN Parameterpost 2 IN 3: TILL/FRÅN Paramerpost 3 1. Motsvarar versionsnumret, t. ex. 3.0 eller 3.01 Med denna inställning fungerar styringångarna enligt beskrivningen i driftsinstruktionen 3ZX1012-0RW22 Med dessa intällninger har varje styringång en IN / UT-funktion, d. v. s. när kontakten mellan OUT L+ DC 24 V (klämma 11) och motsvarande ingång är sluten, så starter motorn med tillhörande parameterpost. När kontakten öppnas kopplar SIKOSTART åter ifrån. Om mer än en styringgång påverkas kopplar SIKOSTART ifrån. Vid drift med tre parameterposter kan en störning kvitteras enbart via PC:n (F9) eller genom frånkoppling av strömförsörjningen. OBS: Markera styringångarna korrekt med medföljande klisteretikett. 40 Mjuk start av polomkopplingsbara motorer med separata lindningar för olika parameterposter För detta behöver du en SIKOSTART med PC-kommunikation. Ta projekteringen hänsyn till tillatna värden för SIKOSTART och motorns startström och starttid. 3/N/PE ~50Hz 230/400 V L1 L2 L3 N PE G1: SIKOSTART 3RW22 F6 F1: Motorgrensäkringar F3: Halvledersäkringar F6: Manöverspänningssäkringar F7: Överlastrelä 1:a varvtalet F8: Överlastrelä 2:a varvtalet S1 K1: Nätkontaktor K5: Kontaktor 1:a varvtalet K6: Kontaktor 2:a varvtalet S1: Nödstopp S2: FRAN-knapp S5: Kvittera störning S7: TILL, 1:a varvtalet S8: TILL, 2:a varvtalet S5 K6 M1: Motor S2 F1 K1 F3 G1 15 14 13 12 11 K5 F7 F8 S8 S7 L1 L2 L3 AC 380- 415 V AC 200- 240 V AC 100- 120 V N/L. DC L+ 24 V 9 IN 1 IN 2 8 Reset 7 Stör6 ning 5 4 Startskedet 3 slut 2 Broms1 kont. 10 T1 T2 T3 S7 K5 K6 S8 K6 K5 S7 S8 K1 K5 K6 F7 K5 N K6 K1 F8 2W 2V 2U M 3~ 1W 1V 1U M1 41 42 F12 K8 K30 K30 Tillslagsfördröjning K10, K20, K30 c:a 200 ms K30 K20 K22 K10 N K22 K9 K32 K10 K8 K22 K12 S31 F32 K12 K12 K9 K20 S30 K20 K10 S21 F22 S20 K30 K20 K8 S11 S10 G1: SIKOSTART 3RW22 F1: Motorförgreningssäkringar F3: Halvledarsäkringar F5: Manöverspänningssäkring F6: Manöverspänningssäkring F11, F21, F31: Motorförgreningssäkringar F12, F22, F32: Överlastrelä K1: Nätkontaktor K8: Hjälpkontaktor sörning K9: Hjälpkontaktor startskedet slut K10, K20, K30: Motorkontaktor K12, K22, K32: Motorkontaktor S1: Nödstopp S5: Kvittera störning S10, S20, S30: FRAN-tangent S11, S21, S31: TILL-tangent M1: Motor K10 K32 K9 K32 K20 K8 S1 L1 L2 L3 N PE F5 K9 S5 F6 K10 1 2 4 3 5 6 K1 K10 Bromskont. Startskedet slut Störning K20 K30 L1 L2 L3 T1 T2 T3 M1 F12 K12 K1 F3 F11 F1 G1 15 AC 380-415V 14 AC 200-240V 13 AC 100-120V 12 N/L . 11 DC L+ 24V 10 IN 1 9 IN 2 8 IN 3 7 3/N/PE~ 50 Hz 230/400 V M 3~ U V W K20 M2 F22 K22 F21 M 3~ U V W K30 M3 F32 K32 F31 M 3~ U V W Mjukstart för seriell start av 3 motorer med 3 parameterposter För detta behöver du en SIKOSTART med PC-kommunikation. Ge akt på tillåtna värden för SIKOSTART: så och motorns startström och startid vid projekteringen. Software-Produktschein Software Product Sheet Certificat de Logiciel Name ..........................................................COM SIKOSTART Package name / Logiciel Ziel-Hardware .............................................Elektron. Motorsteuergerät 3RW22..-..B1. Hardware product / Matériel Gewährleistungsklasse .............................C Siemens leistet Gewähr dafür, daß die Software ordnungsgemäß dupliziert und auf der in der Dokumentation genannten Hardware ablauffähig ist. Siemens warrants that the Software is properly duplicated and compatible with the Hardware mentioned in the Documention. L’ obligation de garantie fournie par SIEMENS consistera à vérifier la bonne reproduction dü logiciel et son fonctionnement sür le matériel mentionné dans la documentation. Bereich Antriebs-, Schalt- und Installationstechnik 92220 Amberg Antriebs-, Schalt- und Installationstechnik von Siemens © Siemens Aktiengesellschaft Änderungen vorbehalten Printed in the Fed. Rep. of Germany