Download DVD Service Manual - Wiki Karat
Transcript
Service Manual DVD LIVANCE GDP 3100 GMI9400 ʀ GDP 3105 GMI9800 ǵ Grundig Service Hotline Deutschland… …Mo.-Fr. 8.00-18.00 Uhr Technik: Zusätzlich erforderliche Unterlagen für den Komplettservice Additionally required Service Documents for the Complete Service Service Manual Sicherheit Safety TV TV SAT VCR/LiveCam HiFi/Audio Car Audio Telekommunikation Fax: Planatron (8.00-22.00 Uhr) 0180/52318-99 Ersatzteil-Verkauf: Telefon: Fax: Mo.-Fr. 8.00-19.00 Uhr 0180/52318-40 0180/52318-50 Kundendienst/Werkstätten: Mo.-Fr. 8.00-18.00 Uhr Telefon: Fax: Materialnr./Part No. 720108000000 gebührenpflichtig Materialnummer/Part Number 720105409500 Änderungen vorbehalten/Subject to alteration • Printed in Germany E-BS-SA15 1201 http://www.grundig.com 0180/52318-41 0180/52318-49 0180/52318-48 0180/52318-42 0180/52318-43 0180/52318-44 0180/52318-45 0180/52318-51 0180/52318-52 0180/52318-46 Allgemeiner Teil / General Section Livance – GDP 31… Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Materialnummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. Inhaltsverzeichnis Table of Contents Seite Allgemeiner Teil ................................. 1-2…1-18 Page General Section .................................. 1-2…1-18 Messgeräte / Messmittel .............................................................. Geräteübersicht ........................................................................... Technische Daten ........................................................................ Ausbauhinweise ........................................................................... Servicehinweise ........................................................................... Bedienhinweise ............................................................................ 1-2 1-3 1-4 1-5 1-7 1-8 Test Equipment / Jigs .................................................................. 1-2 DVD Overview ............................................................................. 1-3 Specifications ............................................................................... 1-4 Disassemly Instructions ............................................................... 1-5 Service Instructions ...................................................................... 1-7 Operating Hints .......................................................................... 1-13 Service- und Sonder-Funktionen ........ 2-1…2-2 Service and Special Funtions ............. 2-3…2-4 Software-Upgrade ........................................................................ 2-1 Initialisierung des Gerätes ........................................................... 2-1 Servicemenü ................................................................................ 2-1 Software Upgrade ........................................................................ 2-3 Initialization of the Set .................................................................. 2-3 Service Menu ............................................................................... 2-3 Platinenabbildungen und Schaltpläne ................................. 3-1…3-32 Layout of PCBs and Circuit Diagrams ......................... 3-1…3-32 Verdrahtungsplan ......................................................................... 3-1 Blockschaltplan ............................................................................ 3-2 – Laufwerksteuerung ................................................................... 3-2 – Digital-Platte ............................................................................. 3-2 IC-Blockdiagramme ..................................................................... 3-3 Netzteil-Platte ............................................................................... 3-7 Digital-Platte ................................................................................. 3-9 • Hauptschaltplan (P1) .............................................................. 3-11 • Audio/Interface (P2) ................................................................ 3-13 • Frontend (P3) .......................................................................... 3-15 • SDRAM (P4) ........................................................................... 3-15 • FLASH (P5) ............................................................................. 3-16 • Interface (P6) .......................................................................... 3-16 Bedieneinheit ............................................................................. 3-17 Laufwerk-Platte .......................................................................... 3-21 Oszillogramme ........................................................................... 3-29 Steckerübersicht ........................................................................ 3-31 Wiring Diagram ............................................................................ 3-1 Block Circuit Diagram .................................................................. 3-2 – Drive Control ............................................................................ 3-2 – Digital Board ............................................................................. 3-2 IC Block Diagrams ....................................................................... 3-3 Power Supply Board .................................................................... 3-7 Digital Board ................................................................................ 3-9 • Main Circuit Diagram (P1) ....................................................... 3-11 • Audio/Interface (P2) ................................................................ 3-13 • Frontend (P3) .......................................................................... 3-15 • SDRAM (P4) ........................................................................... 3-15 • FLASH (P5) ............................................................................. 3-16 • Interface (P6) .......................................................................... 3-16 Keyboard Control ....................................................................... 3-17 Drive Board ................................................................................ 3-21 Oscillograms .............................................................................. 3-29 Connection Overview ................................................................. 3-31 Explosionszeichnung und Ersatzteillisten .............................. 4-1…4-6 Exploded View and Spare Parts Lists ................................. 4-1…4-6 Allgemeiner Teil General Section Messgeräte / Messmittel Test Equipment / Jigs Regeltrenntrafo, Zweikanaloszilloskop, Digitalmultimeter Variable isolating transformer, Dual channel oscilloscope, Digital multimeter Beachten Sie bitte das Grundig Messtechnik-Programm, das Sie unter folgender Adresse erhalten: Please note the Grundig Catalog "Test and Measuring Equipment" obtainable from: Grundig AG Geschäftsbereich Instruments Test- und Mess-Systeme Würzburger Str. 150, D 90766 Fürth Tel.: 0911 / 703-4540; Fax: 0911 / 703-4130 eMail: [email protected] Internet: http://www.grundig-instruments.de "Dolby", "Dolby Pro Logic", "AC 3" ist gefertigt unter Lizenz von Dolby Laboratories Licensing Corporation. "Dolby", "Dolby Pro Logic", "AC 3" und das Doppel-D-Symbol " " sind Warenzeichen der Dolby Laboratories Licensing Corporation. Copyright 1992 Dolby Laboratories, Inc. Alle Rechte vorbehalten. ij 1-2 "Dolby", "Dolby Pro Logic", "AC 3" manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby", "Dolby Pro Logic", "AC 3" and the double-D symbol " " are trademarks of the Dolby Laboratories Licensing Corporation. Copyright 1992 Dolby Laboratories, Inc. All rights reserved. ij GRUNDIG Service Livance – GDP 31… Allgemeiner Teil / General Section Bausteinübersicht Table of Modules Geräteübersicht DVD Overview GDP 3100 GDP 3105 S./P. 3-8 Netzteil / Power Supply • • S./P. 3-9 S./P. 3-11 S./P. 3-13 S./P. 3-15 S./P. 3-15 S./P. 3-16 S./P. 3-16 Digital-Platte / Board • Hauptschaltplan / Main Circuit Diagram (P1) • Audio/Interface (P2) • Frontend (P3) • SDRAM (P4) • FLASH (P5) • Interface (P6) • • S./P. 3-17 Bedieneinheit / Keyboard Control S./P. 3-21 Laufwerk-Platte / Drive Board • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • DVD-Video DVD-R (für Authoring / for authoring use) Audio-CD CD-R CD-RW Video-CD S-VCD MP3-CD 2 Laser (DVD / CD) PAL-Wiedergabe / Playback NTSC-Wiedergabe / Playback Konverter / Converter (PAL-NTSC / NTSC-PAL) Feature-Übersicht Table of Features OSD Bildschirmschoner / Screen Saver Virtual Surround Sound Digital-Audio-Decoder (AC3, MPEG2) Digital-Audio-Decoder (DTS) Kindersicherung / Child Lock Digital Sound Processing Dauerlauf-Wiedergabe / Continuous Playback EURO-AV-Buchse / Socket TV EURO-AV-Buchse / Socket Video Data-Link (IR-Fernbedienung – EURO-AV-Kontakt 8 / IR Remote – EURO-AV contact 8) S-Video-Ausgang / Output Digital-Audio-Ausgang optisch / Digital Audio Output optical (AC3 / MPEG2 / DTS / PCM) Digital-Audio-Ausgang koaxial / Digital Audio Output coaxial (AC3 / MPEG2 / DTS / PCM) LINE-Ausgangs-Buchsen / Output Sockets Subwoofer-Ausgangs-Buchse / Output Socket 5.1 Audio-Ausgangs-Buchsen / Output Sockets Kopfhörerbuchse / Headphone Socket 3.5mm Jog / Shuttle Energiesparend / Low Power (Standby <0.2W) Energiesparend / Low Power (Standby <5W) GRUNDIG Service 1-3 Allgemeiner Teil / General Section Livance – GDP 31… Technische Daten Specifications Netzspannung: 220V-240V~, 50/60Hz Supply Voltage: 220V-240V~, 50/60Hz Leistungsaufnahme: ca. 20W Power Requirement: ca. 20W Standby: < 5W Standby: < 5W Umgebungstemperatur: +10°C … +35°C Ambient Temperature: +10°C … +35°C Wiedergabe-Norm: PAL, 50Hz, 625 Zeilen NTSC, 60Hz, 525 Zeilen Playback Norm: PAL, 50Hz, 625 lines NTSC, 60Hz, 525 lines Norm-Konverter: PAL – NTSC / NTSC – PAL Norm Converter: PAL – NTSC / NTSC – PAL Wiedergabe-System: DVD-Video, VCD, SVCD, Audio-CD Multistandard PAL/NTSC CD-R, CD-RW Playback System: DVD-Video, VCD, SVCD, Audio-CD Multi-standard PAL/NTSC CD-R, CD-RW DVD Disk Format: Durchmesser 8cm und 12cm DVD Disc Format: Diameter 8cm and 12cm Video Format Signal: Digital-Kompression: Digital MPEG2 für DVD / SVCD MPEG1 für VCD Video Format Signal: Digital compression: Digital MPEG2 for DVD / SVCD MPEG1 for VCD DVD Horiz. Auflösung: Vert. Auflösung: 50Hz 720 Pixel 576 Zeilen 60Hz 720 Pixel 480 Zeilen DVD Horiz. resolution: Vert. resolution: 50Hz 720 pixel 576 lines 60Hz 720 pixel 480 lines VCD Horiz. Auflösung: Vert. Auflösung: 50Hz 352 Pixel 288 Zeilen 60Hz 352 Pixel 240 Zeilen VCD Horiz. resolution: Vert. resolution: 50Hz 352 pixel 288 lines 60Hz 352 pixel 240 lines SVCD Horiz. Auflösung: Vert. Auflösung: 50Hz 580 Pixel 576 Zeilen 60Hz 480 Pixel 480 Zeilen SVCD Horiz. resolution: Vert. resolution: 50Hz 580 pixel 576 lines 60Hz 480 pixel 480 lines VCD-Standbilder (VCD 2.0) 50Hz Horiz. Auflösung: 704 Pixel Vert. Auflösung: 576 Zeilen 60Hz 704 Pixel 480 Zeilen VCD still picture (VCD 2.0) Horiz. resolution: Vert. resolution: 50Hz 704 pixel 576 lines 60Hz 704 pixel 480 lines Audio Format Digital: Analog: MPEG/Dolby Digital DTS PCM 16, 20, 24 bit 48 / 96kHz Stereoton, Dolby Surround, 3D Ton Audio Performance Signal: DVD: Analog fs 96kHz fs 48kHz VCD: fs 44,1kHz CD: fs 44,1kHz Rauschabstand (1kHz): >90dB Dynamik (1kHz): >90dB Übersprechdämpfung (1kHz): >95dB 4Hz … 44kHz 4Hz … 22kHz 4Hz … 20kHz 4Hz … 20kHz Audio Format Digital: Analog: MPEG/Dolby Digital DTS PCM 16, 20, 24 bit 48 / 96kHz Stereo sound, Dolby Surround, 3D Sound Audio Performance Signal: DVD: Analog fs 96kHz fs 48kHz VCD: fs 44.1kHz CD: fs 44.1kHz Signal-to-noise ratio (1kHz): >90dB Dynamic range (1kHz): >90dB Crosstalk damping (1kHz): >95dB 4Hz … 44kHz 4Hz … 22kHz 4Hz … 20kHz 4Hz … 20kHz Anschlussbuchsen/Umschalter Connection sockets/Switches Digital-Audio-Buchse: 1 Cinch Digital Audio Socket: 1 cinch Audio-Buchsen: 2 Cinch Audio Sockets: 2 cinch Euro-AV-Buchse: mit RGB-Ausgang 21-polig (IR Steuerung über Pin 8) 0,7VSS / 75Ω Euro-AV Socket: with RGB output 21 pin (IR control via Pin 8) 0.7VPP / 75Ω 1-4 GRUNDIG Service Livance – GDP 31… Allgemeiner Teil / General Section Ausbauhinweise Disassembly Instructions 1. DVD/CD aus defektem Laufwerk entfernen – Gehäuseoberteil abnehmen (Punkt 2). – Mit einem dünnen Schraubendreher durch das Loch 3 (Fig. 9) den Schieber ca. 2cm nach innen schieben und Schublade herausziehen. 1. Opening the Tray when the Drive is Defective – Remove the Cabinet Upper Part (Point 2). – Insert a thin screw driver through the hole 3 (Fig. 9), push the slider about 2cm in inward direction then pull out the tray. 2. Gehäuseoberteil – 3 Schrauben I (Fig. 2) herausdrehen. – Gehäuseoberteil nach hinten schieben und abnehmen. 2. Cabinet Upper Part – Undo the 3 screws I (Fig. 2). – Slide the upper part of the cabinet to the rear then remove it. Montagehinweis: – Gehäuseoberteil über der Rastnase H (Fig. 1) aufsetzen. – Gehäuseoberteil im Bereich der Rastnase und an den Seitenteilen vorsichtig zusammendrücken und in die Frontblende schieben. Reassembly hint: – Place the upper part of the cabinet on the locking lug H (Fig. 1). – Carefully press together the upper part of the cabinet in the area of the locking lug and the side parts then slide it into the front trim. 3. Frontblende – Schublade öffnen (bei defektem Laufwerk siehe Punkt 1), 2 Rastnasen N (Fig. 4) lösen und Schubladenblende abnehmen. – 2 Schrauben E (Fig. 1) herausdrehen. – 6 Rastnasen F / G lösen und Frontblende abnehmen. – Gegebenenfalls Steckverbindung lösen. 3. Front Trim – Open the tray (with a defective drive mechanism, see Point 1), undo the 2 locking lugs N (Fig. 4) then remove the front trim of the tray . – Undo the 2 screws E (Fig. 1). – Undo the 6 locking lugs F / G then remove the front trim. – Unplug the connector if necessary. 4. Bedieneinheit – Frontblende abnehmen (Punkt 3). – 2 Schrauben L (Fig. 3) herausdrehen. – Bedieneinheit links vorsichtig anheben, dabei Rastnasen M (Fig. 3) lösen, dann Rastnasen Z lösen und Bedieneinheit herausnehmen. 4. Keyboard Control – Remove the front trim (Point 3). – Undo the 2 screws L (Fig. 3). – Carefullly lift the left side of the control. In doing that, first disengage the locking lugs M (Fig. 3, then the locking lugs Z, and finaly remove the control unit. 5. Netzteil – 4 Schrauben A (Fig. 1) und Schraube K (Fig. 2) herausdrehen. – Netzteil herausnehmen. – Gegebenenfalls Steckverbindung lösen. 5. Power Supply – Undo the 4 screws A (Fig. 1) and the screw K (Fig. 2). – Remove the power supply from the unit. – Unplug the connector if necessary. 6. Digital-Platte – 4 Schrauben C / D (Fig. 1) und Schraube drehen. – Digital-Platte herausnehmen. – Gegebenenfalls Steckverbindungen lösen. 6. Digital Board – Undo the 4 screws C / D (Fig. 1) and the screw J (Fig. 2). – Remove the digital board. – Unplug the connectors if necessary. J (Fig. 2) heraus- Achtung: Nach dem Tausch der Digital-Platte, des EEPROM´s (U7) oder des FLASH (U15) muss ein Software-Upgrade (Seite 2-1) durchgeführt werden. 7. Laufwerkeinheit – Frontblende abnehmen (Punkt 3). – 4 Schrauben B / C (Fig. 1) herausdrehen. – Laufwerkeinheit nach links schieben und herausnehmen. – Gegebenenfalls Steckverbindungen lösen. Montagehinweis – Die Digital-Platte muss sich bei der Montage über den Füßen des Laufwerks befinden. Attention: After replacing the digital board, the EEPROM (U7), or the FLASH (U15) a software upgrade must be carried out (page 2-3). 7. Drive Mechanism Unit – Remove the front trim (Point 3). – Undo the 4 screws B / C (Fig. 1). – Slide the drive mechanism unit to the left then remove it. – Unplug the connectors if necessary. Reassembly hint – For reassembly, the digital board must be located above the feet of the drive mechanism. I J K Fig. 2 A C B D G F G H F E E Fig. 1 GRUNDIG Service G M Z L Fig. 3 1-5 Allgemeiner Teil / General Section Livance – GDP 31… 8. Laufwerkeinheit zerlegen – Laufwerkeinheit ausbauen (Punkt 7). 8. Disassembling the Drive Mechanism Unit – Remove the drive mechanism unit (Point 7). 8.1 Laufwerk-Platte ausbauen – 2 Schrauben O (Fig. 5) herausdrehen und Laufwerk-Platte abnehmen. – Gegebenenfalls Steckverbindungen lösen. Achtung: Die Lasereinheit ist sehr empfindFLEXPRINT lich gegen statische Aufladungen (MOSBauteile)! Schließen Sie deshalb die Flexprintleitung zur Lasereinheit vor dem Lösen der Steckverbindung mit einer Büroklammer kurz oder bringen Sie die Schutzlötstellen P (Fig. 6) an. 8.1 Removing the Drive Board – Undo the 2 screws O (Fig. 5) then remove the drive board. – Unplug the connectors if necessary. Attention: The laser unit is very sensitive to FLEXPRINT static charges (MOS components)! For this reason, before disconnecting the Flexprint lead from the laser unit, shortcircuit it by means of a paper clip or apply the protective soldering points P (Fig. 6). 8.2 Schublade ausbauen – Zahnrad DM11 (Fig. 7) in Pfeilrichtung drehen bis sich die Schublade bewegt, dann komplett herausziehen. – 2 Schrauben Q (Fig. 8) herausdrehen. – Rastnasen R (Fig. 8) lösen und Laufwerkoberteil abnehmen. – Schublade abnehmen. Montagehinweis: – Zahnrad DM14 (Fig. 9) so drehen, dass zwischen den Markierungen A der Steg B des Zahnrades DM16 gegenüber steht. – Schublade so aufsetzen, dass der mittlere Zahn D (Fig. 10) der Schublade in die markierte Lücke C des Zahnrades greift. – Schublade durch Montage des Laufwerkoberteils fixieren. 8.3 Lademotor ausbauen – Riemen DM07 (Fig. 9) abnehmen. – 2 Schrauben S (Fig. 9) herausdrehen und Lademotor herausnehmen. 8.4 Sledge-Motor ausbauen – Laufwerk-Platte ausbauen (Punkt 8.1). – 2 Schrauben V (Fig. 11) herausdrehen und Sledge-Motor nach unten herausnehmen. 8.2 Removing the Tray – Turn the toothed wheel DM11 (Fig. 7) in direction of the arrow until the tray moves then pull out the tray. – Undo the 2 screws Q (Fig. 8). – Undo the locking lugs R (Fig. 8) then remove the top part of the drive mechanism. – Remove the tray. Reassembly hint: – Turn the toothed wheel DM14 (Fig. 9) so that it faces on the rib B the toothed wheel DM16 between the marks A. – Fit the tray so that the centre tooth D (Fig. 10) of the tray engages into the marked gap C of the toothed wheel. – Fix the tray by mounting the upper part of the drive mechanism. 8.3 Removing the Loading Motor – Remove the belt DM07 (Fig. 9). – Undo the 2 screws S (Fig. 9) then remove the loading motor. 8.4 Removing the Sledge Motor – Remove the drive board (Point 8.1). – Undo the 2 screws V (Fig. 11) then remove the sledge motor in downward direction. N DM11 Fig. 4 Fig. 7 R Q R O 3Q Fig. 5 Fig. 8 DM07 DM16 P DM14 B S A Fig. 6 1-6 Fig. 9 GRUNDIG Service Livance – GDP 31… Allgemeiner Teil / General Section 8.5 Laufwerk ausbauen – Laufwerk-Platte ausbauen (Punkt 8.1). – Gegebenenfalls Kabel frei legen. – 4 Schrauben T (Fig. 11) herausdrehen. – Rastnasen U (Fig. 11) lösen und Laufwerk herausnehmen. Montagehinweis zum Einbau eines neuen Laufwerks: – Flexprint an der Lasereinheit und an CN100 der Laufwerkplatte anschließen. – werkseitig angebrachte Schutzlötstellen der Lasereinheit entfernen (Fig. 6) 8.5 Removing the Drive Mechanism – Remove the drive board (Point 8.1). – Expose the cable if necessary. – Undo the 4 screws T (Fig. 11). – Undo the locking lugs U (Fig. 11) then remove the drive mechanism. Instructions for Mounting a new Drive Mechanism – Connect the Flexprint lead to the laser unit and to CN100 on the drive board. – Remove the factory-applied protective soldering joints from the laser unit (Fig. 6). U T C V D Fig. 10 Fig. 11 Servicehinweise Service Instructions 1. Wichtige Masseverbindungen! Beim Zusammenbau des Gerätes ist darauf zu achten, dass die Masseverbindungen zwischen den einzelnen Platinen und dem Rahmen sowie dem Laufwerk und dem Rahmen gewährleistet sind. 1. Important: Chassis Connections! When reassembling the machine it is essential to observe that the chassis connections between the individual circuit boards and the frame as well as between the Drive Mechanism and the frame are in good order. 2. Durchführen von Messungen Bei Messungen mit dem Oszilloskop an Halbleitern sollten Sie nur Tastköpfe mit 10:1 - Teiler verwenden. Außerdem ist zu beachten, dass nach vorheriger Messung mit AC-Kopplung der Koppelkondensator des Oszilloskops aufgeladen sein kann. Durch die Entladung über das Messobjekt können diese Bauteile beschädigt werden. 2. Carrying out Measurements When making measurements on semi-conductors with an oscilloscope, ensure that the test probe is set to 10:1 dividing factor. Further, please note that if the previous measurement is made on AC input, the coupling capacitor in the oscilloscope will be charged. Discharge via the item being checked can damage components. 3. Messwerte und Oszillogramme Bei den in den Schaltplänen und Oszillogrammen angegebenen Messwerten handelt es sich um Näherungswerte! 3. Measured Values and Oscillograms The measured values given in the circuit diagrams and oscillograms are approximates! GRUNDIG Service 1-7 Dieses Kapitel enthält Auszüge aus der Bedienungsanleitung. Weitergehende Informationen entnehmen Sie bitte der gerätespezifischen Bedienungsanleitung, deren Materialnummer Sie in den entsprechenden Ersatzteillisten finden. AUF EINEN BLICK AUF EINEN BLICK ______________________________________________________________________ ______________________________________________________ Die Vorderseite des DVD-Players Die Rückseite des DVD-Players Allgemeiner Teil / General Section 1-8 Bedienhinweise ǵ A B C AUDIO OUT L R Ton-Ausgangsbuchsen (linker/rechter Kanal) zum Anschließen einer HiFi-Anlage. Schaltet den DVD-Player aus Stand-by ein und wieder aus (Stand-by). Der DVD-Player wird beim Ausschalten nicht vollständig vom Stromnetz getrennt. EURO AV 8 Startet die Wiedergabe; länger drücken (4 Sekunden), schaltet die Funktion Videostrobe ein. DIGITAL AUDIO OUT 7 Einmal drücken aktiviert die Funktion „RESUME”; zweimal drücken schaltet auf „STOPP“. Ton-Ausgangsbuchse (koaxial) für PCM/MPEG2/ AC3/ DTS-Signale, zum Anschließen eines digitalen Mehrkanal Audio-/Videoverstärkers. 220-240 V~ 50/60 Hz 20 W Buchse für Netzkabel. 9 ə Zum Öffnen und Schließen der Schublade. A Stand-by Anzeige. B Anzeige. C Schublade für DVD/CD. ➞ TV Bild-/Ton-Ausgangsbuchse, zum Anschließen eines Fernsehgerätes. Vorsicht: Schließen Sie keine Geräte an, wenn der DVD-Player eingeschaltet ist. Berühren Sie nicht die Innenseite der Buchsen und Stecker der Verbindungskabel. Eine elektrostatische Entladung kann den DVD-Player beschädigen. Die Anzeigen des DVD-Players DVD VCD CD DISK 88888 »ŀ« Wiedergabe. » !« Pause/Standbild. » DVD« DVD eingelegt. Video-CD eingelegt. »0 : 0 0 : 0 0 « Gesamtspielzeit oder abgelaufene Spielzeit in Stunden, Minuten und Sekunden, Nummer des Titels einer DVD und Nummer des Abschnitts einer DVD oder CD oder Nummer des Musiktitels einer CD. 6 7 Livance – GDP 31… GRUNDIG Service DEUTSCH » VCD« Die Fernbedienung Sprachbezogene Einstellungen 9 Schaltet den DVD-Player aus Stand-by ein (die rote Anzeige am DVD-Player leuchtet) und wieder aus (Stand-by). 1…0 Ziffern-Tasten für verschiedene Eingaben. v Vergrößert Szenen bei der Wiedergabe. b Zum Markieren und wiederholten Abspielen von Abschnitten bei DVDs und Video-CDs oder Titel bei Audio-CDs. Nach der ersten Inbetriebnahme des DVD-Players wird automatisch das Menü »Player language« (Gerätesprache) eingeblendet. Sie können jetzt die Sprache der Benutzerführung wählen. Mit dieser Festlegung werden automatisch die Sprache des DVD-Menüs und die Synchronsprache des Tons in der gleichen Sprache eingestellt. Player language Deutsch English Wählt während der Wiedergabe verschiedene Blickwinkel (KameraStandorte) von bestimmten Szenen oder Passagen der DVD. Italiano Nederlands i Ruft das Hauptmenü des DVD-Players auf. Portugues d Schaltet den Ton des Fernsehgerätes stumm (Mute). S x Verlässt das Menü oder schaltet zum übergeordneten Menüpunkt. Svenska Tele Pilot 81 D Wählen in den Menüs verschiedene Funktionen. Wählen in den Menüs verschiedene Funktionen; » a « verlässt das Menü oder schaltet zum übergeordneten Menüpunkt. OK Blendet während der Wiedergabe verschiedene Informationen (zum Beispiel Titel-/ Kapitelnummer, Spielzeit) auf dem Bildschirm des Fernsehgerätes ein. Bestätigt in den Menüs angewählte Funktionen. . Ruft während der Wiedergabe das Discmenü der DVD/ Video-CD auf. Title Ruft während der Wiedergabe das Titelmenü der DVD auf. c Markiert Szenen der DVD. ! Standbild bei DVDs und Video-CDs; Pause bei Audio-CDs. Länger drücken schaltet in Zeitlupe (DVD). 7 Unterbricht jede Lauffunktion. Hinweis: Wenn diese Einstellung nicht mit »OK« bestätigt wird, erscheint nach dem erneuten Einschalten wieder das Menü »Player language« (Gerätesprache). Diese Einstellungen können Sie auch nach der ersten Inbetriebnahme jederzeit ändern, siehe Einstellungen im Kapitel „Sprache der Bildschirmmenüs wählen“ auf Seite 24 und im Kapitel „Spracheinstellungen DVD-Player an das Fernsehgerät anpassen Bildschirmformat Ihres Fernsehgerätes wählen Haben Sie ein Fernsehgerät mit dem Bildformat 16:9, dann wählen Sie die Einstellung »16 : 9«. Diese Grundeinstellungen haben auch Einfluss auf Einstellungen im Menüpunkt »Bild«. Bei einem herkömmlichen Fernsehgerät mit dem Bildformat 4:3 wählen Sie die Einstellung »4 : 3«. 1 Hauptmenü mit »i« aufrufen. TV Format 4:3 16:9 Breitbild 2 Menü »Installation« mit » S« oder » A« anwählen mit »OK« aktivieren, oder direkt mit »1 … 0« anwählen. 8 Startet die Wiedergabe. 5 Wählt während der Wiedergabe den vorherigen Titel/Abschnitt. 6 Wählt während der Wiedergabe den nächsten Titel/Abschnitt. m Schaltet während der Wiedergabe verschiedenen Geschwindigkeiten. auf Bildsuchlauf rückwärts in , Schaltet während der Wiedergabe verschiedenen Geschwindigkeiten. auf Bildsuchlauf vorwärts in d Schaltet während der Wiedergabe um zwischen Original- und Synchronsprache einer DVD. TV Schaltet die Fernbedienung von der Bedienung Ihres DVD PLayers um auf die Bedienung eines Fernsehgerätes, die Möglichkeiten sind auf Seite 30 beschrieben. y Zum Anwählen und Einblenden von Untertiteln der DVD während der Wiedergabe. 3 Zeile » TV Format« mit » S« oder » A« anwählen und mit »OK« aktivieren. Auswählen und Aufrufen 4 Benötigtes Bildformat (4:3 oder 16 : 9 Breitbild) mit »S« oder »A« wählen und mit »OK« bestätigen 11 1-9 Allgemeiner Teil / General Section 8 AS mit »OK« bestätigen. DEUTSCH TV select and choose as 1 Gewünschte Sprache der Bildschirmmenüs mit » A« oder » S« wählen und Francais n Español Title ____________________________________________________ Livance – GDP 31… GRUNDIG Service INBETRIEBNAHME AUF EINEN BLICK ______________________________________________________________________ KINDERSICHERUNG __________________________________________________________________ ________________________________________________ Mit der Kindersicherung können Sie: Inhalt der DVD autorisieren – Die Schublade des DVD-Players sperren; DVDs können Spielfilme anbieten, deren Inhalt oder auch Szenen nicht für Kinder geeignet sind. Diese DVDs enthalten Informationen, die diesen Inhalt oder diese Szenen markieren und sind mit Kennzahlen für Level von 1 bis 8 versehen. Sie können eine der Kennzahlen anwählen und damit alternative Szenen zur Wiedergabe autorisieren. – Szenen von DVDs oder Video-CDs, die nicht für Kinder geeignet sind, sperren oder alternative Szenen auswählen. Schublade des DVD-Players sperren und freigeben 1 Hauptmenü mit »i« aufrufen. Kindersicherung 1 Inhaltssteuerung Schublade des DVD-Players sperren aus 2 Gerätesperre **** 5 Installation Auswählen und Aufrufen ǵ 2 Ton 3 Disc Präferenzen 4 Kindersicherung 2 Zeile »Kindersicherung« mit » S« oder » A« anwählen mit »OK« beenden zurück direkt mit »1 … 0« anwählen. Auswählen und Aufrufen beenden aktivieren, oder direkt mit »1 … 0« anwählen. 3 Mit den Ziffern-Tasten »1« »9« »9« »9« eingeben. zurück Inhaltssteuerung 1 Land USA unbeschränkt 2 Zugangs Level – Das Menü » Kindersicherung« wird eingeblendet, der Status der Kindersicherung (»EIN« oder »AUS«) wird angezeigt. 4 Zeile »Gerätesperre« mit » S« oder » A« anwählen mit »OK« aktivieren. Kindersicherung 1 Inhaltssteuerung 2 Zeile »Kindersicherung« mit » S« oder » A« anwählen mit »OK« aktivieren, oder 1 Hauptmenü mit »i« aufrufen. Player Menü 1 Bild Allgemeiner Teil / General Section 1 - 10 KINDERSICHERUNG Auswählen und Aufrufen beenden zurück 3 Mit den Ziffern-Tasten »1« »9« »9« »9« eingeben. – Das Menü » Kindersicherung« wird eingeblendet, der Status der Kindersicherung (»EIN« oder »AUS«) wird angezeigt. 4 Zeile » Inhaltssteuerung« mit »OK« aktivieren. 5 Zeile » Land« mit »OK« aktivieren. 6 Gewünschtes Land mit » S« oder » A« anwählen und mit »OK« aktivieren. AUS 2 Gerätesperre 5 DVD-Player mit » A« oder » S« sperren (»EIN«) und mit »OK« bestätigen. Zugangs Level 1 beenden zurück 6 Menü mit »i« verlassen. 7 Zeile » Zugangs Level« mit » S« oder » A« anwählen und mit »OK« aktivieren. 2 Auswählen und Aufrufen 3 8 Gewünschte Kennzahl des Levels (von »1« bis »8«) mit » S« oder » A« 4 5 Hinweis: 6 Die Taste » ə « am DVD-Player ist gesperrt, bei jedem Tastendruck wird »D« angezeigt. Eine Disc, die sich im DVD-Player befindet, kann abgepielt werden. 7 anwählen und mit »OK« aktivieren 9 Menü mit »i« verlassen. 8 Ľ Auswählen und Aufrufen Schublade des DVD-Players freigeben Gerätesperre AUS 1 Zum Freigeben der Schublade die Punkte 2 bis 5 im Kapitel „Schublade des DVD-Players sperren“ wiederholen, mit » A« oder » S« die Anzeige » AUS« wählen und mit EIN 20 21 Livance – GDP 31… GRUNDIG Service DEUTSCH Auswählen und Aufrufen BILD-EINSTELLUNGEN ______________________________________________________________ ___________________________________________ Bildformat für Ihr Fernsehgerät wählen Diese Einstellung ist abhängig vom gewählten TV-Format, siehe Kapitel „Bildformat des Fernsehgerätes wählen”, auf Seite 11. Filterfunktionen wählen 1 Hauptmenü mit »i« aufrufen. Bild 1 Format Letterbox 2 Menü »Bild« mit » S« oder » A« anwählen mit »OK« aktivieren, oder 2 Zusatzfunktionen Wurde Bildformat 4:3 gewählt, können Sie einstellen: »Pan&Scan« für eine Breitbild-Wiedergabe vergrößert auf volle Bildschirmhöhe, bei der der linke und rechte Rand des Bildes beschnitten ist, oder »Letterbox« für eine Breitbild-Wiedergabe mit schwarzen Balken am oberen und unteren Bildschirmrand des Fernsehgerätes. Wurde Bildformat 16:9 gewählt, können Sie einstellen: »TV Einstellung« für eine Formatumstellung durch das Fernsehgerät; oder »Automatik« für eine automatische Anpassung des Bildformats durch den DVD-Player; oder »Original« für eine 4:3 Wiedergabe mit schwarzen Balken am linken und rechten Bildschirmrand des Fernsehgerätes; oder »Cinema Zoom«, hier wird das Bild auf die Breite des Bildschirm vergrößert, der obere und untere Rand des Bildes ist beschnitten. direkt mit »1 … 0« anwählen. Auswählen und Aufrufen beenden Letterbox Horizontalfilter scharf mittel 1 Hauptmenü mit »i« aufrufen. aktivieren. 2 Menü »Bild« mit » S« oder » A« anwählen mit »OK« aktivieren, oder direkt mit »1 … 0« anwählen. beenden zurück Format Pan & Scan Letterbox 3 Zeile » Format« mit » S« oder » A« anwählen und mit Horizontalfilter wählen Diese Einstellung optimiert mit einer Weichzeichnerfunktion Computergrafiken und Fotos bei der Wiedergabe. 1 Zeile » Horizontalfilter« mit » S« oder » A« anwählen und mit »OK« 2 Zusatzfunktionen Auswählen und Aufrufen 3 Zeile » Zusatzfunktion« mit » S« oder » A« anwählen und mit zurück weich Bild 1 Format Livance – GDP 31… GRUNDIG Service BILD-EINSTELLUNGEN Auswählen und Aufrufen 2 Gewünschte Einstellung (»scharf«, »mittel« oder »weich«) mit » S« oder » A« wählen und mit Vertikalfilter 4 Gewünschte Einstellung für Bildformat 4:3 (»Pan&Scan« oder »Letterbox«) mit » S« oder » A« wählen und mit Vertikalfilter normal Diese Einstellung optimiert die flackerreduzierte Wiedergabe von Standbildern bei der Wiedergabe. Flimmerreduktion gewünschte Einstellung für Bildformat 16:9 Breitbild (»TV Einstellung«, »Automatik«, »Original« oder »Cinema Zoom«) mit » S« oder » A« wählen und mit Auswählen und Aufrufen 1 Zeile » Vertikalfilter« mit » S« oder » A« anwählen und mit »OK« aktivieren. 2 Gewünschte Einstellung (»normal« oder »Flimmerreduktion«) mit » S« oder 5 Menü mit »i« verlassen. » A« wählen und mit 3 Menü mit »i« verlassen. 22 23 1 - 11 Allgemeiner Teil / General Section DEUTSCH Auswählen und Aufrufen PERSÖNLICHE EINSTELLUNGEN ___________________________________________ _________________ Einstellungen im Menü »Installation« 1 Hauptmenü mit »i« aufrufen. Installation 1 Gerätesprache Transparenz der Bildschirmmenüs einstellen Transparenz 4:3 3 TV Norm PAL 4 Zusatzfunktionen aktivieren. aus Deutsch 2 TV Format 25 % 2 Menü »Installation« mit » S« oder » A« anwählen mit »OK« aktivieren, 50 % oder 2 Zeile » Transparenz« mit »OK« aktivieren. 75 % direkt mit »1 … 0« anwählen. Auswählen und Aufrufen 3 Gewünschte Einstellung (25%, 50% oder 75%) mit » S« oder » A« wählen beenden zurück und mit »OK« bestätigen. Hinweis: Die weitere Bedienung entnehmen Sie bitte den folgenden Kapiteln, jeweils ab Pkt. 1. Gerätesprache Deutsch 1 Zeile » Bildschirmdisplay« mit » S« oder » A« wählen und mit »OK« Allgemeiner Teil / General Section 1 - 12 PERSÖNLICHE EINSTELLUNGEN Auswählen und Aufrufen Sprache der Bildschirmmenüs wählen Hinweis: Bei der Anwahl der Zeile »aus« werden die Bildschirmmenüs nicht transparent dargestellt. 4 Zurückschalten zum Menü » Zusatzfunktion« mit »x«. Hiermit stellen Sie die „Sprache” der Bildschimmenüs des DVD-Players ein. English Francais Nederlands Italiano Softwarestatus und Händlermenü 1 Zeile » Gerätesprache« mit » S« oder » A« anwählen und mit »OK« aktivieren. Español Hier können Sie sich über die Version der Software Ihres DVD-Players informieren. Die Zeile » Händler Servicemenü« ist Ihrem Fachhändler vorbehalten. Portugues 2 Gewünschte Sprache mit » S« oder » A« wählen und mit »OK« Svenska S bestätigen. Auswählen und Aufrufen Entsprechend der Ausstattung Ihres Fernsehgerätes muss die Farbnorm der Bildschirmmenüs des DVD-Players an das Fernsehgerät angepasst werden. Einstellung »NTSC« für Fernsehgeräte mit NTSC-Norm, Einstellung »PAL« für Fernsehgeräte mit PAL-Norm, Einstellung »Auto« für Fernsehgeräte mit MultiNorm TV Norm NTSC PAL Auto 1 Zeile » Servicemenü« mit » S« oder » A« wählen und mit »OK« Servicemen 1 Systeminformation TV System einstellen aktivieren. 2 Händler Servicemenü 2 Zeile » Systeminformationen« mit » S« oder » A« wählen und mit »OK« aktivieren. Auswählen und Aufrufen beenden zurück 3 Menü mit »i« verlassen. 1 Zeile » TV Norm« mit » S« oder » A« anwählen und mit »OK« aktivieren. Auswählen und Aufrufen 2 Gewünschte Einstellung (» NTSC«, » PAL« oder » Auto«) mit » S« oder » A« wählen und mit 3 Menü mit »i« verlassen. Bildschirmmenüs und Anzeige des DVD-Players einstellen 1 Hauptmenü mit »i« aufrufen. 2 Menü »Installation« mit » S« oder » A« anwählen mit »OK« aktivieren, oder Deutsch 2 TV Format 4:3 3 TV Norm PAL 4 Zusatzfunktionen Auswählen und Aufrufen beenden GRUNDIG Service 24 3 Zeile » Zusatzfunktion« mit » S« oder » A« anwählen und mit 25 Livance – GDP 31… zurück direkt mit »1 … 0« anwählen. DEUTSCH Installation 1 Gerätesprache This chapter contains excerpts from the user manual. For further particulars please refer to the appropriate user manual the part number of which is indicated in the relevant spare parts list. OVERVIEW PERSÖNLICHE EINSTELLUNGEN ___________________________________________ Spracheinstellungen ________________________________________________________________________ Livance – GDP 31… GRUNDIG Service Operating Hints The front of the DVD player 1 Hauptmenü mit »i« aufrufen. Disc Präferenzen 1 Synchronsprache Deutsch 2 Untertitel Disc-Vorgabe 3 Menüsprache Deutsch 2 Menü »Disc Präferenzen« mit » S« oder » A« anwählen mit »OK« aktivieren, oder ǵ direkt mit »1 … 0« anwählen. Auswählen und Aufrufen beenden zurück Hinweis: Die weitere Bedienung entnehmen Sie bitte den folgenden Kapiteln, jeweils ab Pkt. 1. Synchronsprache des Tons wählen Synchronsprache Deutsch Englisch Französisch A Wenn auf der eingelegten DVD mehrere Sprachen zur Verfügung stehen, wird der Ton in der von Ihnen gewählten Sprache wiedergegeben. Ist die gewählte Synchronsprache auf der DVD nicht vorhanden, schaltet der DVD-Player auf die erste Synchronsprache der DVD. 9 Niederländisch Italienisch Spanisch 1 Zeile » Synchronsprache« mit » S« oder » A« wählen und mit 8 Portugiesisch Schwedisch S Auswählen und Aufrufen 2 Gewünschte Synchronsprache mit » S« oder » A« wählen und mit »OK« 7 bestätigen. Sprache der Untertitel wählen Untertitel Dänisch Norwegisch Finnisch AUS Wenn auf der eingelegten DVD Untertitel zur Verfügung stehen, werden diese in der von Ihnen gewählten Sprache wiedergegeben. Ist die gewählte Sprache der Untertitel nicht auf der DVD vorhanden, schaltet der DVD-Player auf die erste Sprache der DVD. B C Switches the DVD player to and from stand-by mode. Switching the DVD player off does not mean it is disconnected from the mains. Starts playback. Press and hold down (4 seconds) to switch the video strobe function on. Press once to activate the ”RESUME” function. Press twice to switch to ”STOP” mode. ə Opens and closes the disc compartment. A Stand-by indicator. B Display. C Compartment for DVDs/CDs. Disc-Vorgabe 1 Zeile » Untertitel« mit » S« oder » A« anwählen und mit »OK« aktivieren. 2 Gewünschte Sprache mit » S« oder » A« wählen und mit »OK« Ľ Auswählen und Aufrufen aktivieren. Hinweis: Bei der Anwahl der Zeile »AUS« werden die Untertitel ausgeblendet. Sprache der DVD Menüs wählen Menüsprache Deutsch Wenn auf der eingelegten DVD Menüs in verschiedenen Sprachen zur Verfügung stehen, kann die gewünschte Sprache gew Englisch Französisch 1 Zeile » Menüsprache« mit » S« oder » A« anwählen und mit »OK« Portugiesisch aktivieren. Schwedisch Auswählen und Aufrufen 26 2 Gewünschte Sprache des DVD Menüs mit » S« oder » A« wählen und mit mit »OK« bestätigen. S 3 Menü mit »i« abschalten. 6 1 - 13 Allgemeiner Teil / General Section Niederländisch Italienisch Spanisch OVERVIEW The back of the DVD player The remote control 9 AUDIO OUT L R Audio output jacks (left/right channel) for connection to a HiFi system. ➞ TV Video/audio output jack for connecting a television set. EURO AV DIGITAL AUDIO OUT Audio output jack (coaxial) for PCM/MPEG2/AC3/DTS signals, for connecting a digital multichannel audio/video amplifier. 220-240 V~ 50/60 Hz 20 W Socket for power cord. Title TV Caution: Do not connect any devices while the DVD player is switched on. Never touch the inside of the sockets and plugs of the connecting cables. An electrostatic discharge can damage the DVD player. Tele Pilot 81 D 1 ... 0 Numeric keys for various inputs. v Zooms in on scenes during playback. b For marking and repeating sections on DVDs and video CDs or tracks on audio CDs. n Selects various camera angles for certain scenes or passages on the DVD during playback. i Calls up the DVD player menu. d Switches the sound of the television set off (mute). x Quits the menu or returns to the previous menu level. AS Select various functions in the menus. as Select various functions in the menus; » a « quits the menu or returns to the previous menu level. OK Displays various information on the television screen during playback, such as the title or chapter number and playing time. Confirms selections made from the menus. . Calls up the disc menu of the DVD/video CD during playback. Title Calls up the title menu of a DVD during playback;. c Marks scenes on a DVD. ! Freeze-frame for DVDs and video CDs. Pause for audio CDs Press and hold down for slow motion (DVD). The display elements of the DVD player DVD VCD CD DISK 88888 »ŀ« Playback. Switches the DVD player on from stand-by mode (the red indicator on the DVD player is lit) and off again (stand-by). 7 Interrupts the currently running function. 8 Starts playback. 5 Selects the previous title or section during playback. 6 Selects the next title or section during playback. Pause/Freeze-Frame. m Switches to reverse frame search at various speeds during playback. » DVD« DVD inserted. , Switches to forward frame search at various speeds during playback. d Switches between the original and the dubbed language during DVD playback. TV Switches the remote control from video recorder operation to TV operation, see the options described on page 30. y For selecting and displaying subtitles on the DVD during playback. » VCD« VCD inserted. »0 : 0 0 : 0 0 « Total or elapsed playing time in hours, minutes and seconds. 7 8 Livance – GDP 31… GRUNDIG Service ENGLISH » !« Allgemeiner Teil / General Section 1 - 14 OVERVIEW PARENTAL LOCK _____________________________________________________________________ Setting the language With the parental lock you can: – Lock the disc tray of the DVD player. When the DVD player is first operated, the »Player language« menu appears automatically. You can now choose the language of the user guide. When this is selected, the language of the DVD menu and the dubbed language are automatically set in the same language. Player language Deutsch English _________________________________________________________ Livance – GDP 31… GRUNDIG Service OPERATION – Block scenes which are not appropriate for children from DVDs or video CDs, or select alternative scenes. Locking and releasing the disc tray of the DVD player 1 Select the desired language for the screen menus using » A« or » S« and press »OK« to confirm. Francais Portugues Svenska S select and choose Locking the disc tray of the DVD player Note: If this setting is not confirmed with »OK«, the »Player language« menu appears when the system is switched on again. Player Menu 1 Picture 2 Sound 3 Disc preferences You can change these settings at any time after first operating the system, see the settings in the ”Selecting the language of the screen menu” chapter on page 24 and in the ”Language settings” chapter on page 26. 4 Child lock **** 5 Installation select and choose back 2 Select the »Child lock« line with » S« or » A« and activate with »OK«, or select directly with »1 ... 0«. 3 Enter »1« »9« »9« »9« with the number keys. – The »Child lock« menu is displayed, the parental lock status (»On« or »Off«) is shown. 4 Select the »Player lock« line with » S« or » A« and activate with »OK«. Child lock 1 Content control Selecting the screen format of your television set Off 2 Player lock 5 Lock the DVD player with » A« or » S« (»On«) and confirm with »OK«. If your television has a 16:9 screen format, then select the »16 : 9« setting. These default settings also have an influence on the settings in the »Picture« menu item. On a conventional television set with a 4:3 screen format, select the »4 : 3« setting. 16:9 widescreen 1 Press »i« to call up the main menu. exit Adapting the DVD player to the television set TV format 4:3 ǵ Nederlands Italiano Español select and choose exit back 6 Press »i« to quit the menu. Note: The » ə « button on the DVD player is locked and »D« is displayed each time it is pushed. A disc in the DVD player can be played. 1 Press »i« to call up the main menu. 2 Select the »Player menu« menu with » S« or » A« activate with »OK«, or Releasing the disc tray of the DVD player select directly using Player lock Off 3 Select the »TV format« line with » S« or » A« and activate with »OK«. select and choose On 4 Select the screen format required (4:3 or 16:9 wide screen) with »S« or 1 To release the disc tray, repeat steps 2 to 5 in the ”Locking the disc tray on the DVD player” chapter, select the »Off« display with » A« or » S« and confirm with »OK«. »A« and confirm with »OK«. 11 20 1 - 15 Allgemeiner Teil / General Section ENGLISH select and choose Authorising the contents of a DVD Selecting the picture format for your television Films on DVD may be wholly or partially unsuitable for children. Such DVDs contain information which identifies these scenes, providing them with ratings from 1 to 8. You can select one of the ratings and thereby authorise alternative scenes for playback. Child lock 1 Content control This setting is dependent on the chosen TV format, see the ”Selecting the screen format for your television” chapter on page 11. If 4:3 format is selected, you can set: »Pan&Scan« for wide-screen playback using the full height of the screen, but with the left and right edges of the picture cropped. »Letterbox« for wide-screen playback with black bars on the top and bottom edges of the screen 1 Press »i« to call up the main menu. Off 2 Player lock 2 Select the »Child lock« line with » S« or » A« and activate with »OK«, or If 16:9 format is selected, you can set: »Use TV settings« for resetting the format by the television set. »Automatic« for adapting the picture format automatically by the DVD player. »Original« for 4:3 playback with black bars on the left and right edges of the screen. »Cinema zoom«, where the picture is enlarged to the width of the screen, and the upper and lower edges of the picture are cropped. select directly using select and choose exit back 3 Enter »1« »9« »9« »9« with the number keys. – The »Child lock« menu is displayed, the parental lock status (»On« or »Off«) is shown. Content control 1 Country USA None 2 Access level 4 Activate the »Country control« line with »OK«. Picture 1 Format 5 Activate the » Country« line with »OK«. select and choose Letterbox Access level 1 2 1 Press »i« to call up the main menu. 2 Extended settings exit back ___________________________________________________ Allgemeiner Teil / General Section 1 - 16 PICTURE SETTINGS PARENTAL LOCK ________________________________________________________________________ 2 Select the »Picture« menu with » S« or » A« activate with »OK«, or 6 Select the country with » S« or » A« and activate with »OK«. select directly with »1 ... 0«. 7 Select the » Access level« line with » S« or » A« and activate with »OK«. select and choose exit back 3 Select the » Format« line with » S« or » A« and activate with »OK«. 8 Select the desired rating (from »1« to »8«) using » S« or » A«, and activa- 3 te with »OK«. 4 Format Pan & Scan 5 Letterbox 9 Press »i« to quit the menu. 6 7 4 Select the desired setting for 4:3 format (»Pan&Scan« or »Letterbox«) with » S« or » A« and press »OK« to confirm; or 8 Ľ select the desired setting for 16:9 widescreen format (»Use TV settings«, »Automatic«, »Original« or »Cinema zoom«) with » S« or » A« and press »OK« to confirm. select and choose 21 22 5 Press »i« to quit the menu. Livance – GDP 31… GRUNDIG Service ENGLISH select and choose __________________________________________________ Settings in the »Player menu« menu Selecting filter functions 1 Press »i« to call up the main menu. Picture 1 Format 2 Select the »Picture« menu with » S« or »A«activate with »OK«, or exit back English 2 TV Format 4:3 3 TV standard PAL 4 Extended settings select directly with »1 ... 0«. select and choose 1 Press »i« to call up the main menu. Installation 1 Player language Letterbox 2 Extended settings select and choose 3 Select the »Extended settings« line with » S« or » A« and activate with exit Player language Deutsch Medium Soft 2 Select the »Player menu« menu with » S« or »A« and activate with »OK«, or select directly using back »OK«. Note: For further operation, see the following sections, each one starting from Step 1. Horizontal filter Crisp Livance – GDP 31… GRUNDIG Service CUSTOM SETTINGS PICTURE SETTINGS ____________________________________________________________________ Selecting the horizontal filter Selecting the language of the screen menu With this you set the language of the DVD player’s screen menu. English Francais This setting optimises the soft focus function, computer graphics and photos when playing back. Nederlands Italiano 1 Select the » Player language« line with » S« or » A« and activate with »OK«. Español Portugues 1 Select the » Horizontal filter« line with » S« or » A« and activate with 2 Select the desired language with » S« or » A« and confirm with »OK«. Svenska S »OK«. select and choose 2 Select the desired setting (»Crisp«, »Medium« or »Soft«) with » S« or » A« select and choose TV standard NTSC Vertical filter Normal Anti-flicker Vertical filter PAL Auto This setting optimises the flicker-reduced reproduction of freeze frames when playing back. 1 Select the » TV standard« line with » S« or » A« and activate with »OK«. 2 Select the desired setting (» NTSC«, » PAL« or » Auto«) with » S« or » A« 1 Select the » Vertical filter« line with » S« or » A« and activate with »OK«. and press »OK« to confirm. select and choose 2 Select the desired setting (»Normal« or »Anti-flicker«) with » S« or » A« and press »OK« to confirm. select and choose Setting the TV system The colour norm of the DVD player’s screen menus has to be adapted to the format of the television. Select »NTSC« for televisions with NTSC norm, »PAL« for televisions with PAL norm,and »Auto« for televisions with multi-norm. and press »OK« to confirm. 3 Press »i« to quit the menu. 3 Press »i« to quit the menu. Setting the screen menu and display of the DVD player 1 Press »i« to call up the main menu. Installation 1 Player language 2 Select the »Player menu« menu with » S« or »A« activate with »OK«, or English 2 TV Format 4:3 3 TV standard PAL 4 Extended settings select directly with »1 ... 0«. 3 Select the »Extended settings« line with » S« or » A« and activate with exit ENGLISH back 23 24 Note: For further operation, see the following sections, each one starting from Step 1. 1 - 17 Allgemeiner Teil / General Section »OK«. select and choose CUSTOM SETTINGS ________________________________________________________________ Language settings Selecting the transparency of the screen menus Transparency Off 25 % 1 Select » Onscreen display« by pressing » S« or » A« and then press »OK« to activate it. 50 % 2 Activate the » Transparency« line with »OK«. 75 % English 2 Subtitle Disc-Vorgabe 3 Menu language English select and choose press »OK« to confirm. back Note: When the »Off« line is selected, the screen menus have a solid background. Selecting the dubbed language Audio language Software status and dealer menu Deutsch Englisch Here you can get information about your DVD player’s software version. The » Dealer Service menu« line is reserved for the authorised dealer. Französisch If several languages are available on the current DVD, the sound is played back in the language you have selected. If the language you select is not on the DVD, the first dubbed language available is automatically selected. Niederländisch Italienisch 1 Select the » Dealer Service menu« line by pressing » S« or » A« and then Spanisch Portugiesisch press »OK« to activate it. 2 Dealer Service menu »OK«, or exit 4 Return to the »Extended settings« menu by pressing »x«. Service menu 1 System information 2 Select the »Disc preferences« menu with » S« or »A« and activate with select directly using 3 Select the desired setting (25%, 50% oder 75%) with » S« or » A« and select and choose 1 Press »i« to call up the main menu. Disc preferences 1 Audio language Allgemeiner Teil / General Section 1 - 18 CUSTOM SETTINGS ___________________________________________________________________ 1 Select the » Audio language« line by pressing » S« or » A« and then press »OK« to activate it. Schwedisch S 2 Select the » System informationen« line by pressing » S« or » A« and then select and choose press »OK« to activate it. select and choose 2 Select the desired dubbed language with » S« or »A« and confirm with »OK«. exit back 3 Press »i« to quit the menu. Selecting the language for the subtitles Subtitle Danish Norwegian Finnish Off If subtitles are available on the current DVD, they are played back in the language you have selected. If the language you have selected for the subtitles is not on the DVD, the first language available is automatically selected. Disc default 1 Select the » Subtitle« line with » S« or » A« and activate with »OK« 2 Select the desired language with » S« or » A« and activate with »OK«. Ľ select and choose Note: When the »Off« line is selected, the subtitles are not displayed. Selecting the language of the DVD menus Menu language German If a DVD has menus in several languages, you can select the language of your choice. English French Dutch Italian 1 Select the » Menu language« line with » S« or » A« and activate with »OK«. Spanish Portuguese Schwedish ENGLISH select and choose 26 3 Press »i« to switch off the menu. Livance – GDP 31… GRUNDIG Service 25 2 Select the desired language for the DVD menus using » S« or » A« and press »OK« to confirm. S Livance – GDP 31… Service- und Sonder-Funktionen / Service and Special Functions Service- und Sonder-Funktionen Software-Upgrade Achtung: Sollte während dem Software-Upgrade eine Störung (z.B. Stromausfall) auftreten, so sind eventuell die Gerätefunktionen und ein Neustart der Upgrade-Funktion nicht mehr gewährleistet. In diesem Fall müssen Sie den eingebauten FLASHIC (U15) durch einen vorprogrammierten ersetzen (siehe entsprechende Ersatzteilliste). – Software-Upgrade-CD (siehe entsprechende Ersatzteilliste) einlegen und die Hinweise am Display und am Bildschirm des Fernsehgerätes beachten. 2.2 Händler Servicemenü – Servicemenü aufrufen (Punkt 2). – "Händler Servicemenü" anwählen mit der Taste 2, oder mit den Tasten S / A und der Taste »OK« bestätigen. – Zahlenfolge "8 5 0 0" eingeben. Hinweis: Die weiteren Menü´s sind entsprechend der Menü-Übersicht aufrufbar (Punkt 3). Gewährleistung Wir weisen ausdrücklich darauf hin, dass nur von GRUNDIG freigegebene System-Software zulässig ist. Wurde als Fehlerursache festgestellt, dass eine aus nicht legitimierten Quellen gleich welcher Herkunft stammende oder eine veränderte System-Software in die Geräte geladen wurde, so ist dies ein Fremdeingriff. Ein Fremdeingriff führt zum Erlöschen jeglicher Gewährleistungsansprüche. GRUNDIG muss daher alle aus diesen Gründen resultierenden Kostenerstattungen generell ablehnen. Instandsetzungskosten, auch innerhalb der Gewährleistungszeit, gehen in diesen Fällen zu Lasten des Händlers bzw. des Endkunden. – Systemmeldungen Das System gibt bei Funktionswahl und bei auftretenden Fehlern (z.B. Disc-, Bedien- oder Gerätefehler) Meldungen aus, die im unteren Bereich des Bildschirmes kurzzeitig angezeigt werden. Initialisierung des Gerätes Am Gerät gleichzeitig die Tasten 7 / 8 drücken und das Gerät am Netz anschließen. Dadurch wird das Gerät softwaremäßig in den Auslieferzustand zurück gesetzt. Dabei werden Grundeinstellungen geladen und die kundenspezifischen Daten gelöscht. 2.2.1 System Einstellungen – Demo Bei eingeschalteter Demo-Funktion ist die Eject-Taste und der Ein/Aus-Schalter gesperrt. Beenden der Demo-Funktion: – Taste 7 drücken. – Taste ydrücken. 2.2.2 Video Spezial – Format conversion Folgende Formatumwandlungen sind möglich: – Zentrum – Auto – nur 525 Zeilen – nur 625 Zeilen – Video Signal Servicemenü Das Servicemenü gliedert sich in das frei zugängliche Menü "Systeminformation" und das passwort-geschützte "Händler Servicemenü". 1. Tastenfunktionen Die Bedienung des Servicemenü erfolgt über die Fernbedienung. i Player Menü aufrufen / Menü-Funktionen beenden. S / A Menü-Funktion wählen. a übergeordnete Menü-Funktion wählen. s Menü-Funktion aktivieren. OK Menü-Funktion aktivieren. x übergeordnete Menü-Funktion wählen. 1…9 Menü-Funktion direkt aktivieren. y Beendet die Demo-Funktion im Stop-Betrieb. 2. Aufruf des Servicemenü – "Player Menü" mit der Taste »i« aufrufen. – "Installation" anwählen mit der Taste 5, oder mit den Tasten S / A und der Taste »OK« bestätigen. – "Zusatzfunktionen" anwählen mit der Taste 4, oder mit den Tasten S / A und der Taste »OK« bestätigen. – "Servicemenü" anwählen mit der Taste 2, oder mit den Tasten S / A und der Taste »OK« bestätigen. Das Servicemenü gliedert sich gemäß der Menü-Übersicht (Punkt 3) in die einzelnen Untermenü´s. • DAC enable Folgende Digital-Analog-Konverter sind ein-/ausschaltbar: – DAC1 = Grün- / Y-Signal – DAC2 = Blau- / C-Signal – DAC3 = Rot-Signal (Anzeige des aktiven Schaltzustandes) • NTSC Format (60Hz-Format) Folgende 60Hz-Formate sind wählbar: – 525 Zeilen, Norm NTSC – 525 Zeilen, Norm M-PAL • NTSC Composit Folgende NTSC-FBAS-Signal-Formate sind einstellbar: – NTSC USA – NTSC Japan – NTSC Other • PAL Format Folgende PAL-Formate sind einstellbar: – PAL BDGHI – PAL N – PAL N-Combo 2.1 Systeminformation – Servicemenü aufrufen (Punkt 2). – "Systeminformation" anwählen mit der Taste 1, oder mit den Tasten S / A und der Taste »OK« bestätigen. Auf dem Bildschirm erscheint die Systeminformation. Systeminformation Gerät Software-Version Hardware-Version Hardware-Information GDP 3100 SW-Version: 0.79 / 258 Oct 17 2001 HW-Version: 0.03 Copyright: GRUNDIG AG 2001 http://www.grundig.com NDV8602/DVD-5/Pantera-II LE rev 1 R:2 Regional-Code Auswählen und Aufrufen GRUNDIG Service beenden zurück 2-1 Service- und Sonder-Funktionen / Service and Special Functions Livance – GDP 31… 3. Servicemenü-Übersicht Servicemenü Systeminformation 1 Systeminformation 2 Händler Servicemenü GDP 3100 SW-Version: 0.79 / 258 Oct 17 2001 HW-Version: 0.03 Copyright: GRUNDIG AG 2001 http://www.grundig.com NDV8602/DVD-5/Pantera-II LE rev 1 R:2 Auswählen und Aufrufen **** Auswählen und Aufrufen beenden zurück beenden zurück Systemmeldungen AUS EIN Demo AUS EIN System Einstellungen 1 Systemmeldungen 2 Demo 3 Video Spezial Auswählen und Aufrufen Auswählen und Aufrufen beenden Auswählen und Aufrufen zurück Format conversion Video Spezial 1 Format conversion 2 Video Signal Auswählen und Aufrufen Auto beenden zurück Centre Auto 525 Only 625 Only Auswählen und Aufrufen DAC enable 1 DAC1 enable 2 DAC2 enable 3 DAC3 enable Auswählen und Aufrufen DAC… enable EIN EIN EIN AUS EIN beenden zurück Auswählen und Aufrufen Video Signal 1 2 3 4 DAC enable NTSC Format NTSC Composit PAL Format Auswählen und Aufrufen 525 lines NTSC NTSC USA PAL BDGHI NTSC Format 525 lines NTSC 525 lines M-PAL NTSC Composit NTSC USA NTSC Japan NTSC Other beenden zurück PAL Format PAL BDGHI PAL N PAL N-Combo Auswählen und Aufrufen Auswählen und Aufrufen Auswählen und Aufrufen 2-2 GRUNDIG Service Livance – GDP 31… Service- und Sonder-Funktionen / Service and Special Functions Service and Special Functions Software Upgrade Attention: if a failure should occur during the software upgrade (e.g. a mains failure), it may happen that the unit's function and a restart of the upgrade function are no longer possible. If this should be the case, you must replace the integrated FLASH IC (U15) with a preprogrammed IC (see corresponding spare parts list). – Insert the upgrade CD (see corresponding spare parts list) and observe the hints on the display and on the screen of the TV set. Warranty / costs We expressly point out that only operating software authorized by GRUNDIG is allowed. If a failure is caused by an operating software which has been downloaded from not authorized sources, independent of its origin, or a modified software, this represents an outside interference. An outside interference leads to the expiration of any warranty claims. For this reason, GRUNDIG is obliged to generally refuse any payment due to such infringements. In such cases, the repair costs are at the charge of the retailer or the final customer, even within the period of warranty. 2.2 Retailer service menu – Call up the "Service menu" (Point 2). – Call up the "Retailer Service" menu using the 2 button, or use the S / A buttons and confirm with the »OK« button. – Enter the digits "8 5 0 0". Note: the further menus can be called up according to the menu overview (Point 3). 2.2.1 System settings – System messages When selecting a function or in the case of an error (e.g. disc, handling or unit error), the system emits messages which are briefly displayed in the bottom area of the picture screen. – Demo When the demo function is activated, the eject button and the on/off switch are locked. Ending the demo function: – press the 7 button. – press the y button. 2.2.4 Video special Initialization of the Set Press the 7 / 8 buttons on the set at the same time and connect the set to the mains. This resets the software of the set to the factory presettings. The basic settings are loaded and the customer-specific data is cleared. – Format conversion The following format conversions are possible: – Centre – Auto – 525 lines only – 625 lines only Service Menu – Video signal The Service menu is subdivided into the freely accessible "System information" menu and the password-protected "Dealer service menu". 1. Functions of the buttons For navigating in the Service menu, the buttons on the remote control are used. i Call up the Player menu / End the menu functions. S / A Select menu functions. a Select higher menu function. s Activate menu function. OK Activate menu function. x Select higher menu function. 1…9 Activate menu function directly. y Exit demo function in stop mode. 2. Calling up the Service menu – Call up the "Player Menu" using the »i« button. – Select "Installation" using the 5 button, or use the S / A buttons and confirm with the »OK« button. – Select "Additional functions" using the 4 button, or use the S / A buttons and confirm with the »OK« button. – Select the "Service Menu" using the 2 button, or use the S / A buttons and confirm with the »OK« button. The Service menu is subdivided in sub-menus according to the menu overview (Point 3). • DAC enable The following digital-to-analog converters can be activated/deactivated: – DAC1 = Green/Y signal – DAC2 = Blue/C signal – DAC3 = Red signal (indication of the active switching state) • NTSC format (60Hz format) The following 60Hz formats can be selected: – 525 lines, NTSC standard – 525 lines, M-PAL standard • NTSC composite signal The following NTSC composite signal formats can be selected: – NTSC USA – NTSC Japan – NTSC Other • PAL format The following PAL formats can be selected: – PAL BDGHI – PAL N – PAL N-Combo 2.1 System information – Call up the "Service menu" (Point 2). – Select "System information" using the 1 button, or use the S / A buttons and confirm with the »OK« button. The System information menu appears on the picture screen. System information Unit Software version Hardware version Hardware information GDP 3100 SW-Version: 0.79 / 258 Oct 17 2001 HW-Version: 0.03 Copyright: GRUNDIG AG 2001 http://www.grundig.com NDV8602/DVD-5/Pantera-II LE rev 1 R:2 Regional code select and choose GRUNDIG Service exit back 2-3 Service- und Sonder-Funktionen / Service and Special Functions Livance – GDP 31… 3. Service menu overview Service menu System information 1 System information 2 Dealer service menu GDP 3100 SW-Version: 0.79 / 258 Oct 17 2001 HW-Version: 0.03 Copyright: GRUNDIG AG 2001 http://www.grundig.com NDV8602/DVD-5/Pantera-II LE rev 1 R:2 select and choose **** select and choose exit back exit back System message Off On Demo Off On System settings 1 System messages 2 Demo 3 Video special select and choose select and choose exit select and choose back Format conversion Video special 1 Format conversion 2 Video signal select and choose Auto exit back Centre Auto 525 Only 625 Only select and choose DAC enable 1 DAC1 enable 2 DAC2 enable 3 DAC3 enable select and choose DAC… enable On On On Off On exit back select and choose Video Signal 1 2 3 4 DAC enable NTSC Format NTSC Composite PAL Format select and choose 525 lines NTSC NTSC USA PAL BDGHI NTSC Format 525 lines NTSC 525 lines M-PAL NTSC Composite NTSC USA NTSC Japan NTSC Other exit back PAL Format PAL BDGHI PAL N PAL N-Combo select and choose select and choose select and choose 2-4 GRUNDIG Service Netz J3 11 18 Flexprint 33 1 PICK UP J1 6 6 1 J15 SLED MOTOR 2 2 CN620 J10 1 Flexprint 26 CN200 CN630 26 1 1 CN500 1 Flexprint 16 16 J1122 CN610 J9 CN600 1 SPINDLE MOTOR 18 Flexprint 16 Flexprint 11 5 16 TRADE MOTOR LIMIT SWITCH POWER SUPPLY J6 DIGITAL BOARD DVD MECHANISM KEYBOARD CONTROL 3-1 16 1 J1 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams LIMIT SWITCH CN900 U8 CN100 Livance – GDP 31… J5 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Verdrahtungsplan / Wiring Diagram GRUNDIG Service Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Blockschaltplan – Laufwerksteuerung / Block Circuit Diagram – Drive Control PCK UP 5V RFAMP A, B, C, D, E, F IC100 LA9702 I/V FE, TE, … LD, MD, VR, HFM RF LD CD_LD, DVD_LD Servo, DSP CD decoder DVD decoder EQB, EQF (Equalizer Ajust.) F0 , TR SERIAL Data ACT. 384 Fs (16.9 MHz) SpindleDRV. SPINDLE MOTOR IC602 BA6849 MICOM IC500 IC200 LC78661 SPD SBRAKE, SPD_FG, *DMUTE CONTROL Data 34 Digital Board 5V 9V 3V HRST (RESET) 4ch DRV. SLED MOTOR IC601 BA5937 SLD1, 2 PARALLEL Data 106/107 9V 16.9 MHz LOADING MOTOR FD, TD, SLD MLD1, 2 *OPEN, *CLOSE, DMUTE2 Mechanism SW (OPN, CLS, The internal circumference LIMIT) Blockschaltplan – Digital-Platte / Block Circuit Diagram – Digital Board I.R (local) POWER SUPPLY (J1) L U19 9V REG. 5V 12V 30V 15V AOutL U1 AUDIO DAC 3.3V R198 C201 RESET VFD (J6) R U3 AUDIO DRIVER AOutR Q4/Q5 Q1,Q9 MUTE SSPCLK1BF EURO-AV (J5) I.R (external) SSPOUT1BF CVBS / R.G.B STANDBY_LED FLDCS SSPIN1F AUDIO OUT (J5) POWER U5 BUFFER SSPOUT…/SSPCLK… SSPOUT0BF SSPCLK0BF AOUT0 XIO9 XIO10 SSPIN1 1.8V RSTB- U6 1.8V REG. AUDIO-BUS SPDIFO C / Y / CB / CR RXD1 HW_MUTE DVD-DRIVE (J15) SSPIN0 U7 NVM 2k I2C BUS U8 PANTERA CONTROL DATA DRVRST- DVD-DRIVE HRST (J10 / J11) U15 FLASH MEMORY 3-2 ADDR. BUS MA0…MA13 DATA BUS MD0…MD31 ADDRESS BUS LA0…LA18 DATA BUS AD0…AD31 PARALLEL DATA DVD0…7 U22 SDRAM 1M*32bit Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams IC-Blockdiagramme / IC Block Diagrams BA5937 BA6849 GRUNDIG Service PIN NAME DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Channel 1 negative output Channel 1 positive output Channel 1 input Input for channel 1 gain adjustment – – Mute control for channels 1 and 4 GND – Vcc (channel 2) – Loading motor positive output Loading motor negative output Substrate GND Loading motor reverse input Loading motor forward input Channel 3 negative output Channel 3 positive output Loading motor input Channel 3 input Vcc (channel 3) Vcc (channel 1 and 4) Bias amplifier input Input for channel 4 gain adjustment Channel 4 input Channel 4 positive output Channel 1 negative output Substrate GND OUT1-1 OUT1-2 IN1-1 IN1-2 N.C. N.C. MUTE GND N.C. Vcc2 N.C. OUT2-2 OUT2-1 GND REV FWD OUT3-1 OUT3-2 LDIN IN3 Vcc3 Vcc1 VrefIN IN4-2 IN4-1 OUT4-2 OUT4-1 GND PIN NAME DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 – Output – Output – – Output GND Hall signal input Hall signal input Hall signal input Hall signal input Hall signal input Hall signal input Hall bias – For connection of phase compensation capacitor Short brake – Rotation direction detection Output voltage control reference Output voltage control Power save FG signal output Power supply Motor power supply 2 Motor power supply 1 For connection of output current detection resistor N.C. A3 N.C. A2 N.C. N.C. A1 GND H1+ H1– H2+ H2– H3+ H3– VH N.C. CNF SB N.C. FR ECR EC PS FG VCC VM2 VM2 RNF 3-3 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… CS4334 DEM/SCLK 2 LRCK 3 SDATA 1 AGND 6 Serial Input Interface De-emphasis Interpolator ∆∑ Modulator DAC Interpolator ∆∑ Modulator DAC VA 7 Voltage Reference Analog LPF 8 AOUTL Analog LPF 5 AOUTR SDATA 1 8 AOUTL DEM/SCLKK 2 7 VA LRCK 3 6 AGND MCLK 4 5 AOUTR 4 MCLK PIN NAME TYPE DESCRIPTION 1 SDATA Digital input 2 3 4 5 6 7 8 DEM/SCLK LRCK MCLK AOUTR AGND VA AOUTL Digital input Digital input Digital input Analogue output Ground Supply Analogue output Serial Audio Data Input - two’s complement MSB-first serial data is input on this pin. The data is clocked into the CS4334 via internal or external SCLK, and the channel is determined by LRCK. De-Emphasis/External Serial Clock Input - used for de-emphasis filter control or external serial clock input. Left/Right Clock - determines which channel is currently being input on the Audio Serial Data Input pin, SDATA. Master Clock - frequency must be 256x, 384x, or 512x the input sample rate in BRM and either 128x or 192x the input sample rate in HRM. Analog Right Channel Output - typically 3.5 Vpp for a full-scale input signal. Analog Ground - analog ground reference is 0V. Analog Power - analog power supply is nominally +5V. Analog Left Channel Output - typically 3.5 Vpp for a full-scale input signal. VDDIO PWE0ALE LA0 LA1 LA2 LA3 VSSIO RDLHLDA LHLD VDD PCS0 XIO1 XIO2 VDDIO XIO3 XIO4 XIO5 XIO6 VSS XIO7 XIO8 VSSIO XIO9 XIO10 XIO11 XIO12 XIO13 VDDIO XIO14 VDD DSYNC DREQ DCLK DSTB DVD0 VSSIO DVD1 DVD2 DVD3 DVD4 DVD5 VDDIO DVD6 DVD7 MD0 VSSIO MD1 VSS MD2 MD3 VDDIO MD4 MD5 MD6 VSSIO MD7 MD8 MD9 PANTERA 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 VDDIO MD10 MD11 VDD MD12 VSSIO MD13 MD14 MD15 VDDIO DQM1 MA9 MA8 VSSIO MA7 MA6 VSS MA5 VDDIO MA4 MA3 MCLK VSSIO CKE MA2 MA1 VDDIO MA0 MA10 MA11 VSSIO MA12 MA13 VDD CS0VDDIO RASCASWEVSSIO DQM0 DQM2 MD16 VDDIO MD17 MD18 VSS MD19 VSSIO MD20 MD21 MD22 VDDIO MD23 MD24 MD25 VSSIO MD26 MD27 MD28 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 PANTERA 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 AD0 AD1 AD2 VSSIO AD3 AD4 AD5 AD6 AD7 VSS PWE1VDDIO AD8 AD9 AD10 AD11 AD12 AD13 VSSIO ACK SCLK VDD AD14 AD15 PWE2AD16 VDDIO AD17 AD18 AD19 AD20 AD21 AD22 VSSIO AD23 PWE3AD24 AD25 AD26 AD27 VDDIO AD28 AD29 AD30 AD31 VDD VIO0 VIO1 VSSIO VIO2 VIO3 VIO4 VIO5 VIO6 VIO7 VDDIO HSYNC VSYNC VIOCLK VSS COMP RSET CVBS/C Vaa VREF Vssa Y/G Vaa3 C/Cb/B IOM CVBS2/Cr/R VssDAC VddDAC ACLKVdd SCMD ACLKVss MVCKVss SCEN MVCKVdd OSCVdd OSCVss CXO CXI VSSIO RTS0CTS0RXD0 TXD0 SSPOUT0 VDDIO SSPIN0 VDD SSPCLK0 SSPCLK1 SSPOUT1 VSS SSPIN1 RXD1 VSSIO RSTPSRSTLRCLK ACLK VDD PCMCLK VDDIO AOUT0 AOUT1 AOUT2 AOUT3 AIN VSS SPDIF VSSIO CS1DQM3 MD31 MD30 VDDIO MD29 3-4 GRUNDIG Service Livance – GDP 31… MIC Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams SPDIF DAC CCIR656 Port 7 ASP AOP ADC input PCM out Video Port VIDEC DSP SPDIF format HOST D-RAM I-ROM D-ROM SPDIF mod MMU MMU HOST VSD MMU VIQ HOST HOST VRP MMU Cr line buffer Cb line buffer Scaler Merge Macrovision OSD HOST MMU SPU CGMS WSS HOST Module Interfaces SSP0 sync serial peripheral audio freq synth PWM2 PWM1 6 PWM0 SSP1 HOST DVD EDC 11 Data in sync 8 control header sync detect decrypt CD-ROM descramble CSS status control ints FIFO 128x8 Packet Framer MA 32 MD circular buffer Reset 32 HOST DEMUX ctrl system oscillator video freq synth Timer address generator 12 Arbiter regs primary freq synth Watchdog Serial Ports Cr/R Datapath HOST HOST sync serial peripheral HOST UART1 C/Cb/B CVBS/C SDRAM controller UART0 async serial peripheral Y/G 10 MMU async serial peripheral DVD Front End NTSC/PAL & SCART Encoder VOP Y line buffer Program Stream Demux PES/SI Depacketizer MMU MMU Event Tagger Interrupt Routing Host BIU Video Start Code Detector 22 ctrl registers I$ adr decode I$ rd mux Stream Buffer Write Controller AD Xbus interface D$ adr decodeD$ rd mux I$ control I$ Tag 256x18 D$ control I$ 1024x32 D$ Tag 256x20 D$ 256x32 CPU NAME TYPE PIN DESCRIPTION Front End DSYNC DREQ DCLK DSTB DVD[7:0] I O I I I 213 214 215 216 * DVD parallel mode Sector Sync DVD parallel mode Data Request Data sampling clock Parallel mode Data Valid, serial mode Left/Right Clock DVD drive parallel data port, pins: 217, 219-223, 225, 226 External I/O PCS0 XIO[14:1] O B 193 * Peripheral chip select 0, generally used for enabling the program store ROM/FLASH Programmable general purpose I/O also used as peripheral chip select, interrupt, PWM output and other system signals, pins: 195, 197-200, 202-203, 205-209, 211 SDRAM MD[31:0] B * MA[11:0] MA[13:12] MCLK CKE CS0CS1RASCASWEDQM[3:0]- O O O O O O O O O O * 32-33 22 24 35 66 37 38 39 11, 41, 42, 65 Host Interface AD[31:0] LA[3:0] ALE RDACKSCLK PWE[3:0]- B B B B B O B * 184-187 183 189 161 160 * Slave Mode LHLD LHLDA I O 191 190 Bus Hold Request from external master in slave mode Bus Hold Acknowledge in slave mode Comm Ports UART1 RXD1 I 83 UART1 serial data input from external serial device, used for IR receive SSP1 SSPCLK1/CTS1SSPOUT1/DTR1SSPIN1/BAUD1 B B B 87 86 84 SSP1 clock or UART1 Clear to Send signal SSP1 data out or UART1 Data Terminal Ready signal SSP1 data in or 16X clock for USART function in UART1 GRUNDIG Service SDRAM data bus, pins: 227, 229, 231, 232, 234, 235, 236, 238, 239, 240, 2, 3, 5, 7, 8, 9, 43, 45, 46, 48, 50, 51, 52, 54, 55, 56, 58, 59, 60, 61, 63, 64 SDRAM address bus, pins: 12, 13, 15, 16, 18, 20, 21, 25, 26, 28, 29, 30 SDRAM address bus, reserved for pin compatibility with 64Mbit SDRAM SDRAM clock SDRAM Clock Enable SDRAM primary bank chip select SDRAM extension bank chip select SDRAM command bit SDRAM command bit SDRAM command bit SDRAM data byte enables mP multiplexed address/data bus Latched Address [3:0] Address Latch Enable Read Programmable WAIT-/ACK-/RDY- control External bus clock used for programmable host bus peripherals Byte write enable for FLASH, EEPROM, SRAM or peripherals, pins: 145, 156, 170, 182 3-5 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams NAME TYPE PIN DESCRIPTION UART0 RXD0 TXD0 RTS0 CTS0 I B B B 94 93 96 95 UART0 serial data input from external serial device UART0 serial data output to an external serial device UART0 request to send UART0 Clear to Send signal SSP0 SSPOUT0/DTR0 SSPIN0/BAUD0 SSPCLK0/RTS1 B B B 92 90 88 SSP0 data out or UART0 Data Terminal Ready signal SSP0 data in or 16X clock for USART function in UART0 SSP0 clock or Request To Send function in UART1 System Interface RSTPSRST- I O 81 80 RESET_Power- from system, used to reset frequency synthesizer & rest of chip Active low RESET signal for peripheral reset Video Interface CVBS/C Y/G C/Cb/B O O O 118 114 112 Composite video output for NTSC/PAL or Chrominance output for S-Video Luminance for NTSC/PAL S-Video and component output, G output for SCART Chrominance output for NTSC/PAL S-Video, Cb output for component, Blue output for SCART CVBS2/Cr/R IOM VREF RSET COMP VddDAC VssDAC Vaa3 Vaa Vssa O O I O O P P P P P 110 111 116 119 120 108 109 113 117 115 A second CVBS output for composite, Cr output for component, Red output for SCART Cascaded DAC differential output used to dump current into external resistor for power Input voltage reference (1.2V typ) for output DACs Current setting resistor of output DACs Compensation capacitor connection DAC Digital Power/2.5V DAC Digital Ground DAC Analog Power/3.3V DAC Analog Power/2.5V DAC Analog Ground Video Port VIO[7:0] HSYNC VSYNC VIOCLK B B B B 126-131, 133-134 124 123 122 Audio Interface AOUT0 AOUT1 AOUT2 AOUT3 SPDIF ACLK PCMCLK LRCLK AIN O O O O O O O O I 74 73 72 71 68 78 76 79 70 Serial audio output data to audio DAC for Left & Right channels Serial audio output data to audio DAC for Center & LFE channels Serial audio output data to audio DAC for Surround Left & Right channels Serial audio output data to audio DAC for Left & Right channels for down-mixed stereo S/PDIF digital audio output Audio interface serial data clock, common clock for DACs & ADC Audio DAC PCM sampling clock frequency, common clock for DACs & ADC Left/Right Channel clock, common clock for DACs & ADC Digital audio input for digital micro Clock Signals CXI CXO OSCVdd OSCVss MVCKVdd MVCKVss ACLKVdd ACLKVss I O P P P P P P 98 99 101 100 102 104 107 105 Crystal Input pin for on-chip oscillator or system input clock Crystal Output pin for on-chip oscillator Oscillator Power (2.5V) Oscillator Ground Main & Video Clock PLL Power (3.3V) Main & Video Clock PLL Ground Audio clock PLL Power (3.3V) Audio clock PLL Ground Test SCEN SCMD I I 103 106 Scan Chain test enable Scan Chain test mode PWR & GND VDD Vss VDDIO VSSIO P P P P * * * * 3-6 Livance – GDP 31… Bidirectional digital video port data bus Bidirectional HSYNC signal for devices that do not use EAV/SAV codes Bidirectional VSYNC signal for devices that do not use EAV/SAV codes VCLK input/output for Video I/O Port function Core Power =2.5V, pins: 4, 34, 77, 89, 135, 159, 192, 212 Core & Ring Ground, pins: 17, 47, 69, 85, 121, 171, 201, 230 I/O Pad power = 3.3V, pins: 1, 10, 19, 27, 36, 44, 53, 62, 75, 91, 125, 140, 154, 169, 181, 196, 210, 224, 233 I/O Pad ground, pins: 6, 14, 23, 31, 40, 49, 57, 67, 82, 97, 132, 147, 162, 177, 188, 204, 218, 228, 237 GRUNDIG Service Livance – GDP 31… Netzteil / Power Supply Ansicht von der Bestückungsseite / View of Component Side GRUNDIG Service Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams 3-7 AC 220…240V * * 1 * Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 2 * * without Low Power with Low Power Standby Standby 2Ω 1/4W 10Ω 1/4W 1K 2W 50Ω 2W 300Ω 1W 27Ω 2W 27Ω 2W 50Ω 2W 1K 2W 1K 2W - * 3 Low Power Standby Livance – GDP 31… GRUNDIG Service * R106 R202 R204 R206 R237 R240 R241 R242 R243 * Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams * Netzteil / Power Supply 3-8 * Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Digital-Platte / Board Koordinaten für die Bauteile / Coordinates of the Components POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y C5 C14 C15 C16 C17 24 53 54 37 37 99 24 39 39 41 C65 185 89 R23 R24 R25 R26 R27 15 17 24 30 53 13 10 10 10 75 100 TS18 TS19 TS20 TS21 96 98 123 123 75 75 22 24 96 46 38 17 17 12 17 21 57 48 13 20 9 58 75 C46 C47 C48 C49 C50 42 77 89 72 48 71 81 70 67 66 FB1 FID1 FID2 FID3 FID4 21 188 12 120 86 83 89 23 130 50 42 74 30 31 66 66 76 104 68 96 88 C56 C57 C58 C59 C60 34 48 50 42 70 99 62 62 61 29 37 27 53 55 60 62 12 79 79 104 C61 C62 C63 C64 82 82 18 187 53 52 31 99 46 93 100 83 53 9 42 78 71 TS12 TS13 TS14 TS15 TS16 145 166 96 96 95 90 102 78 80 72 18 22 53 136 180 173 40 106 76 12 156 71 67 R88 R89 R90 R91 R134 R135 R136 R137 R138 C110 C111 31 15 15 46 25 89 10 57 54 14 146 76 109 107 130 49 67 63 49 45 182 38 141 141 52 TS1 TS2 TS8 TS9 TS11 C153 C161 C162 C163 C164 R83 R84 R85 R86 R87 53 53 54 86 28 9 41 45 47 90 89 108 90 100 32 53 49 131 12 103 125 134 133 132 149 180 173 172 174 31 R128 R129 R130 R131 R133 C105 C106 C107 C108 C109 C147 C148 C149 C150 C152 86 59 62 67 64 153 136 112 124 119 71 71 82 102 141 141 141 141 TP1 TP3 TP4 C100 C101 C102 C103 C104 R75 R77 R78 R79 R81 7 10 52 95 52 10 C51 C52 C53 C54 C55 132 132 60 12 131 83 FID5 FID7 FID8 R123 R124 R125 R126 R127 SW1 24 62 46 41 35 41 45 47 15 86 72 188 63 67 77 70 70 70 130 130 129 59 92 RP1 RP4 RP12 C142 C143 C144 C145 C146 R69 R70 R71 R72 R73 83 86 100 15 10 64 55 49 41 84 100 100 103 55 9 50 64 12 71 32 124 124 124 124 132 73 53 57 24 68 R118 R119 R120 R121 R122 C95 C96 C97 C98 C99 C136 C137 C138 C139 C141 81 26 26 90 65 9 9 69 74 65 78 92 18 109 134 136 147 153 71 70 35 35 35 35 75 106 R62 R65 R66 R67 R68 R196 R197 R201 R202 R203 R204 U19 U22 47 69 69 69 69 66 71 62 75 9 83 89 85 83 104 83 92 98 104 113 57 57 57 57 75 62 64 50 68 12 C90 C91 C92 C93 C94 D6 D7 D8 D9 D14 R113 R114 R115 R116 R117 48 84 92 92 92 66 10 9 71 9 66 57 76 26 26 103 147 91 100 124 24 93 100 12 96 78 82 39 131 139 U8 U11 U12 U14 U15 C131 C132 C133 C134 C135 R45 R51 R52 R56 R58 99 49 30 89 82 91 75 76 71 71 28 28 27 27 38 89 13 13 12 12 161 50 42 48 50 105 96 92 88 82 R162 R188 R190 R193 R194 C39 C40 C41 C44 C45 C85 C86 C87 C88 C89 10 10 65 82 71 90 22 65 86 18 32 31 84 76 33 14 35 150 29 29 136 71 146 59 67 56 38 157 83 135 D1 D2 D3 D4 D5 R107 R109 R110 R111 R112 U1 U3 U5 U6 U7 53 103 9 50 9 86 39 65 84 22 44 44 68 100 100 45 59 116 47 103 96 33 156 187 29 57 53 78 78 83 C126 C127 C128 C129 C130 R37 R40 R41 R43 R44 R152 R153 R159 R160 R161 C31 C32 C33 C34 C38 57 51 16 28 28 80 16 26 71 93 66 61 71 71 71 125 113 109 12 83 56 158 65 39 39 39 C79 C81 C82 C83 C84 C199 C201 C261 R100 R101 R102 R103 R104 45 40 95 95 88 93 83 103 88 71 66 62 24 102 76 76 157 159 105 110 128 65 24 53 53 53 71 171 TS51 TS52 TS53 TS54 C121 C122 C123 C124 C125 R28 R29 R30 R31 R36 13 13 13 86 53 25 25 21 23 10 47 62 69 69 58 93 85 76 67 91 67 63 59 54 57 41 33 37 37 11 124 82 95 108 124 12 12 12 12 12 R144 R145 R146 R148 R149 C25 C26 C27 C28 C30 C74 C75 C76 C77 C78 C194 C195 C196 C197 C198 86 82 96 22 71 91 91 69 61 38 41 49 38 136 136 110 120 153 159 156 12 C18 C19 C21 C22 C23 R93 R95 R96 R98 R99 R141 R142 R143 104 98 98 77 103 38 51 46 27 17 177 21 12 96 24 63 45 13 28 13 28 R92 C115 C116 C117 C118 C119 C165 C180 C183 C187 C189 66 61 91 65 28 28 40 104 102 104 45 45 54 83 117 101 82 26 12 34 L6 L7 C66 C67 C71 C72 C73 C112 C113 C114 R139 R140 12 173 73 86 TS17 98 80 GRUNDIG Service L10 L11 L12 L13 L14 39 39 68 61 62 89 99 62 46 41 L15 L17 L21 62 62 33 35 29 22 Q1 Q2 Q4 Q5 Q6 21 176 26 29 150 12 89 22 39 71 Q7 Q8 Q9 Q13 Q20 56 51 27 175 54 50 50 10 105 83 Q24 Q25 59 65 83 83 28 3 109 65 31 R1 R2 R3 R4 R5 45 45 45 45 48 39 23 21 41 20 114 133 92 84 100 15 J1 J3 J5 J6 J9 49 5 8 172 141 108 44 106 95 97 R6 R7 R8 R9 R10 49 37 52 41 33 43 38 18 39 43 J10 J11 J12 J15 110 141 114 68 106 106 78 109 R11 R12 R13 R14 R15 29 141 41 52 25 43 50 41 16 25 L3 L4 L5 56 45 45 21 76 71 R17 R18 R19 R20 R22 41 29 41 37 136 21 25 23 25 99 3-9 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Digital-Platte / Board Ansicht von der Bestückungsseite / View of Component Side 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 X 0 Y 3 - 10 0 10 20 30 40 50 60 70 80 90 100 110 GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Digital-Platte – Hauptschaltplan / Digital Board – Main Circuit Diagram (P1) R197 330R From X-BUS CONN. P6 RSTP-FPGA- Reset SW 1 (Option) RS - 232 Video Signals P2 +30V U6 20 19 18 17 16 15 14 13 12 11 C39 0.1uF SSPOUT0B SSPCLK0B SSPCLK1BF SSPOUT1BF MOUNTING / TOOLING HOLES 74VHCT541AMTC Remove copper ring on underside Keep circular arrangement of vias L13 2.2uH SMD TDK R110 SRSTB- 10R SRSTB- P5 C79 0.1UF XM1 . 1 XM1 XM2 1 . . 1 XM3 XM4 1 . ACLK MD[31:16] +12V 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 GNDA C136 0.33uF P2 4:3/16:9 P2 TV_PIN8_EN GNDA AD31 AD30 AD29 AD28 AD27 AD26 AD25 AD24 AD23 AD22 AD21 AD20 AD19 AD18 AD17 P6 PWE 3P6 PWE 2- AD16 P6 SCLKR AD15 AD14 TS8 TS9 Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 R62 33R AD13 AD12 AD11 AD10 AD9 AD8 P6 PWE 1AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 PANTERA-2 (8602) 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 FLASH/XBUS P6 ACK- SCLK U8 MD28 MD27 MD26 VSSIO MD25 MD24 MD23 VDDIO MD22 MD21 MD20 VSSIO MD19 VSS MD18 MD17 VDDIO MD16 DQM2 DQM0 VSSIO WE CAS RAS VDDIO CS0 VDD MA13 MA12 VSSIO MA11 MA10 MA0 VDDIO MA1 MA2 CKE VSSIO MCLK MA3 MA4 VDDIO MA5 VSS MA6 MA7 VSSIO MA8 MA9 DQM1 VDDIO MD15 MD14 MD13 VSSIO MD12 VDD MD11 MD10 VDDIO PRE NC E Vss U7 Vcc M/WC SCL SDA 24C16 8 7 6 5 R56 4k7 R66 R65 R12 33R 33R C65 220pF FPDIN FPDOUT FPDCLK FLD_CS IRIN C64 220pF MD19 MD18 MD17 DQM3- P4 MD16 DQM2DQM0- +5.0V MD[31:16] P4 DQM2- P4 DQM0- P4 WECASRAS- R92 4k7 WE- P4 CAS- P4 RAS- P4 CS0- C150 0.1uF C149 0.1uF C148 0.1uF 22 23 24 25 26 TO Keyboard Control Connector J1 R162 0R STANDBY_LED Q13 BC847AL 4K7 R36 GNDA R91 MA[13:0] P5 Q2 BC847AL 4k7 MA10 MA0 R140 4k7 MA1 MA2 CKE MCLK MA3 MA4 CKE P4 R98 MCLK1 P4 0R MA5 MA6 MA7 PCMCLKB ACLK LRCLK AOUT3 DQM1- P4 MA8 MA9 DQM1MD15 MD14 MD13 MD[15:0] P4 SDRAM 1 2 3 4 RP12 8 7 6 5 33R R84 AOUT0 B PCMCLKBO ACLKO LRCLKO AOUT3O Audio Signals P1 HW_MUTE 33R MD12 MD11 MD10 TXD R123 150R N/A RXD R124 150R N/A XIO8 R127 150R N/A XIO7 R130 150R N/A XIO[1:11] P6 TV_DATA P2 XIO1 0R 1206 N/A 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 33R FLDCS- CS0- P4 MA13 MA12 C147 0.1uF R90 MD7 MD8 MD9 MD4 MD5 MD6 MD2 MD3 MD0 MD1 DVD6 DVD7 DVD0 DVD1 DVD2 DVD3 DVD4 DVD5 XIO14 XIO9 XIO10 XIO11 XIO12 XIO13 XIO7 XIO8 XIO3 XIO4 XIO5 XIO6 XIO1 XIO2 J6 1->n +5.0V 33R XIO4 XIO5 PANTERA PIN 4 ...(TOTAL 8) SHORT WIRES R77 4k7 N/A LA3 R78 4k7 N/A LA2 R79 4k7 N/A LA1 R81 4k7 N/A LA0 Model Option resistors R77 - R81 SMD 0603.. P3 DRVRSTP3 WAIT P3 REQ P3 ENABLE P3 DSYNC P3 DREQ P3 DCLK P3 DSTB P3 DVD[7:0] C71 0.1uF C72 0.1uF C73 0.1uF C74 0.1uF C75 0.1uF C76 0.1uF C77 0.1uF C78 0.1uF 1 2 3 4 R58 4k7 V3.3 33R 8 7 6 5 R83 RXD1 MD22 MD21 MD20 DVD2 DVD[7:0] DCLK SSP0 P3 SSPCLK0B P3 SSPOUT0B P3 SSPIN0 R69 DVD2T 220pF R71 DSYNCT C108 47R N/A D4 3 1 2 1 3 2 C106 47R N/A 47pF N/A R70 DCLKT C107 PANTERA PIN 1 ... (TOTAL 19) 75R DSYNC TV_CLK P2 D5 47pF N/A C83 0.1uF C84 0.1uF C85 0.1uF C86 0.1uF C87 0.1uF C88 0.1uF C89 0.1uF C90 0.1uF C91 0.1uF C92 0.1uF C93 0.1uF C94 0.1uF C95 0.1uF C96 0.1uF C97 0.1uF C98 0.1uF C99 0.1uF C100 0.1uF C101 0.1uF C51 0.1uF LA[3:0] DVD FE +5.0V LA0 LA1 LA2 LA3 P5, P6 PWE0 P5, P6 ALE P5, P6 LA[3:0] P5, P6 RDP6 LHLDA P6 LHLD P6 PCS0- SSPIN1F SSPOUT1BF SSPCLK1BF MD25 MD24 MD23 V1.8 V3.3 P5, P6 AD[31:0] RP4 1 2 3 4 R161 0R BZX84C4V7 GNDA 0R 1206 N/A C127 0.1uF 4 3 2 1 R160 0R MD28 MD27 MD26 BZX84C4V7 C18 470uF 25V 5 6 7 8 P2 TV_PIN16_O SCARTIRIN P2 C105 100uF 50V GNDA R101 47pF N/A C82 100uF 50V C138 0.1uF GNDA GNDA GNDA RP1 33R VSS VCLK VSYNC HSYNC VDDIO VIO7 VIO6 VIO5 VIO4 VIO3 VIO2 VSSIO VIO1 VIO0 VDD AD31 AD30 AD29 AD28 VDDIO AD27 AD26 AD25 AD24 PWE3 AD23 VSSIO AD22 AD21 AD20 AD19 AD18 AD17 VDDIO AD16 PWE2 AD15 AD14 VDD SCLK ACK VSSIO AD13 AD12 AD11 AD10 AD9 AD8 VDDIO PWE1 VSS AD7 AD6 AD5 AD4 AD3 VSSIO AD2 AD1 AD0 +30V SPDIFO P2 MD[15:0] GNDA C137 100uF 16V 3 C119 0.1uF IN L11 39uH 1 2 3 4 5 6 GND GNDA J15 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 COMP RSET CVBS/C VAA VREF VSSA Y/G VAA3 C/Cb/B IOM CVBS2/Cr/R VSSDAC VDDDAC ACLKVDD SCMD ACLKVSS MVCKVSS SCEN MVCKVDD OSCVDD OSCVSS CXO CXI VSSIO RTS0 CTS0 RXD0 TXD0 SSPOUT0 VDDIO SSPIN0 VDD SSPCLK0 SSPCLK1 SSPOUT1 VSS SSPIN1 RXD1 VSSIO RSTP SRST LRCLK ACLK VDD PCMCLK VDDIO AOUT0 AOUT1 AOUT2 AOUT3 AIN VSS SPDIF VSSIO CS1 DQM3 MD31 MD30 VDDIO MD29 2 TAB=GND OUT GNDA C66 100uF 16V 1 C124 0.1uF GNDA VDDIO PWE0 ALE LA0 LA1 LA2 LA3 VSSIO RD LHLDA LHLD VDD PCS0 XIO1 XIO2 VDDIO XIO3 XIO4 XIO5 XIO6 VSS XIO7 XIO8 VSSIO XIO9 XIO10 XIO11 XIO12 XIO13 VDDIO XIO14 VDD DSYNC DREQ DCLK DSTB DVD0 VSSIO DVD1 DVD2 DVD3 DVD4 DVD5 VDDIO DVD6 DVD7 MD0 VSSIO MD1 VSS MD2 MD3 VDDIO MD4 MD5 MD6 VSSIO MD7 MD8 MD9 U19 L7809CD2T L10 39uH C142 Keyboard Control C67 0.1uF XM4 NON-PLATED 125mil DIA. 250mil RING with 8 vias MD29 R51 10R XM3 DQM3MD31 MD30 C104 0.1UF RXD1 AOUT3 C143 100uF 50V +5.0V TO DRIVE BOARD Connector CN900 XM2 SSPIN1F C110 47pF R121 10R SPDIF V3.3 47pF 1 R109 10R AOUT0 V1.8 L12 10uH SMD TDK C103 47R 1k10 1% 0.1UF R159 R45 VA3.3 C145 47uF 50V X1 SRSTLRCLK ACLK R31 10R Analogue Ground Drive Ground 27MHz AT-cut, 2 C111 RXD1 2.2uH SMD TDK SSPCLK1 SSPOUT1 SSPIN1 Digital Ground R43 0R C102 0.1UF C146 47uF 50V SSPOUT0 SSPIN0 SSPCLK0 L15 2.2uH SMD TDK GNDA L14 GNDA U5 VCC OE2 O0 O1 O2 O3 O4 O5 O6 O7 PCMCLKB 0.1uF GNDA C81 0.1UF C144 47uF 50V C115 0.1uF GNDA 5 4 OE1 I0 I1 I2 I3 I4 I5 I6 I7 GND RTS CTS RXD TXD 0.1uF C49 100uF 16V 100uF 16V 0.1uF BUFFOEN C62 47pF 100uF C112 16V C48 0.1uF +5.0V 1 2 3 4 5 6 7 8 9 10 SSPOUT0 SSPCLK0 SSPCLK1 SSPOUT1 C61 47pF C114 SRST- P2, P6 TXD RXD CTS RTS C60 47uF 50V C56 C55 C5 SSP0 C141 0.1uF L17 2.2uH SMD TDK 1.8V LM1117DT-1.8 J1 RSTP- C201 10uF 50V P1 TO DVD FE TS1 V1.8 TOP VIEW T0-252 DPAK 3 C54 470uF 25V N/A 1 C47 0.1uF VIN 3.3V 1 2 3 4 5 6 7 8 9 10 11 TS2 R196 100K IOM +15V C Y CB CR RSET +12V VOUT 2 +5.0V GND FROM POWER SUPPLY V3.3 P3 P3 P3 P3 CVBS_F GREEN_F BLUE_F RED_F V3.3 D14 1N4148 TS51 TS52 TS53 TS54 A RC Reset October 16, 2001 Rev 0.04 GRUNDIG Service 3 - 11 GRUNDIG Service 3 - 12 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Digital-Platte / Board – Audio/Interface (P2) R149 0R R125 100k SCARTIRIN P1 P2 +15V V3.3 R148 220R R128 100k Q7 BC847AL R129 100k Q8 BC847AL C126 1uF R134 330R C129 0.1uF N/A 31 TVPIN8 Digital 4 GND R188 330R 3 LEFT W R190 330R 2 RIGHT R 1 GND C63 R113 22k Q20 BC847AL R114 22k R116 22k 4:3/16:9 P1 Q24 BC847AL 20pF B R118 4k7 C187 1nF TOP VIEW R112 33R SPDIFO P1 R144 150R C161 0.1uF R145 75R SPDIF C180 1nF R115 1k10 1% R119 22k Q25 BC847AL TOP 5 FERRITE BEAD (BLM21A471SG) R111 22k TV_PIN8_EN P1 J3 FB1 BOTTOM CONN TRIPLE RCA VIDEO W/ CHASSY PIN SPDIF_COAX_O C162 R146 100pF 150R R72 0R LEFT Place close to PANTERA. R88 10K U1 8 7 6 5 AOutL VA AGnd AOutR R153 1k10 1% 36 C163 47uF 16V DACOR CS4334 7k5 R6 1k8 10K C14 C21 680pF C165 0.1uF * R1 R9 4k7 47uF 16V R17 7k5 C153 1000uF 10V C25 680pF -In A OutA 47uF 16V U3 38 LM833M 5 -In B OutB +In B 2 R8 1k10 1% * C27 1nF R2 4k7 R20 R87 10k R11 680R R40 4k7 C183 47uF 16V C116 1nF R120 330R 3 4 Q5 BC847AL 5 6 R15 R18 10k L21 10uH SMD TDK 680R C125 1000uF 10V R44 4k7 Q4 BC847AL 7 R126 100k C152 470uF 25V C194 20pF 8 9 C198 20pF P1 TV_CLK C26 0.1uF 7k5 R10 10k 7 +15V R5 10k 1 C23 47uF 16V +15V * R19 4k7 R117 330R 2 1 +In A 37 6 4k7 R3 1k8 C261 0.1uF 3 C113 1nF C19 8 1 SData 2 SCLK 3 LRCK 4 MCLK R13 C189 47uF 16V C118 1000uF 10V C195 20pF 12 100pF R14 1k10 1% C22 47uF 16V 13 C164 0.1uF C199 20pF P1 TV_DATA RIGHT C131 1000uF 10V D1 2 R24 10k 3 R122 10k P1 TV_PIN16_O Q1 BC857AL C134 1nF R23 33R BAT54A R25 1k10 1% C33 0.1uF 18 19 AIR AOL AGND BGND AIL B SWTCH GGND CLKOUT G DATA RGND DATAGND R BLNK VGND BLNKGND VOUT VIN SHIELD TOP VIEW R143 100k 0.1uF C197 20pF Single SCART Connector R26 10k D2 3 +5V R139 75R 21 C139 1000uF 10V Q9 BC847AL H=play L=mute 16 20 C31 C32 1000uF 10V 14 17 H=mute L=play MUTEVCC MTVC HW_MUTE C196 20pF +4.74V 1 C30 0.1uF R194 75R 15 R137 100k +5.0V 10 11 R131 100K *C28 R193 75R AOR BACK PANEL VIEW R4 47uF 16V 7k5 V+ C15 V- AOUT3O ACLKO LRCLKO PCMCLKBO DACOL L3 2 4 B Audio Signals P1 34 R7 C17 1nF 1 32 * R152 1k10 1% 35 FERRITE BEAD SMD1210SBY322513T-600 TV SCART 100pF A3L3 +5.0V 33 J5 *C16 +15V 1 +3.3V SRST- P1 2 H=play L=mute BAT54A MUTE LOGIC VA3.3 C34 30 0.1uF A Video Signals P1 C50 20pF R201 0R 0805 BLUE BLUE_F VA3.3 D6 R29 150R C52 100pF L6 2.2uH SMD TDK C53 56pF Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 R102 150R BAV99/SOT 29 C44 20pF R202 0R 0805 GREEN GREEN_F VA3.3 D7 R28 150R C45 100pF L5 2.2uH SMD TDK C46 56pF R104 150R BAV99/SOT 28 C57 20pF RED_F R203 0R 0805 RED VA3.3 D8 R30 C58 150R 100pF L7 2.2uH SMD TDK C59 56pF R103 150R BAV99/SOT 27 C38 20pF CVBS CVBS_F VA3.3 D9 R27 C40 150R 100pF L4 2.2uH SMD TDK C41 56pF BAV99/SOT R204 0R 0805 R52 150R 0805 Package Size In case of EMI filtering Place close to PANTERA. October 16, 2001 Rev 0.04 3 - 13 GRUNDIG Service 3 - 14 GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Digital-Platte / Board – Frontend (P3) P3 J9 OPTION DSYNC P1 21 20 19 18 17 26 25 DCLK-FE 24 DSYNC 23 22 DERR 21 20 DACK-FE 19 18 DREQ 17 16 DVD0-FE 15 14 DVD1 13 12 DVD2 11 10 DVD3 9 8 DVD4-FE 7 6 DVD5 5 4 DVD6 3 2 DVD7 1 RESET SDD7 SDD6 SDD5 SDD4 SDD3 SDD2 SDD1 SDD0 DGND1 STVALID STCLK STENABLE ERROR (AVRTM) LDRXCK DECSEL (TX_REQ) HOSTSEL (TX_ENABLE) RXD (SBO) TXD (SBI) HOSTRDY (SBT) LDRRDY (WAIT) DGND2 DREQ P1 U11 2 3 5 6 11 10 14 13 TS11 15 1 MUXEN 1Y 1A 1B 2A 2B 3A 3B 4A 4B G A/B 2Y 3Y 4Y 4 DCLK P1 9 12 DSTB P1 DVD4 TS12 +5.0V VCC GND 16 8 74ACT257MTC R67 150R DVD0 7 TOP VIEW GND DCLK GND DBGN GND DERR GND DACK GND DREQ GND STD0 GND SDT1 GND SDT2 GND SDT3 GND SDT4 GND SDT5 GND SDT6 GND SDT7 MULTIPLEXER C109 0.1uF REQ P1 (XIO13) Connector for PANASONIC Drive 13 12 11 10 9 8 7 R136 0R DRVRST- P1 DSTB P1 DCLK P1 DREQ P1 DSYNC P1 ENABLE P1 RXD P1 TXD P1 REQ P1 WAIT P1 RTS P1 CTS P1 DVD[7:0] DVD[7:0] P1 J10 TOP VIEW BACK-END CONNECTOR FOR SANYO DRIVE 15 14 DVD7 DVD6 DVD5 DVD4 DVD3 DVD2 DVD1 DVD0 UDE (DU5) OPTION DVD[7:0] 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 SPDIF CD-Data BCK LRCK C2PO EMPH GND_d 16M GND_d RDY_HIF SCLK RxD TxD GND_d HRST NC FE-SPDIF CDDA-FE BCK-FE LRCK-FE C2PO 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 TS13 +5.0V ENABLE SSPCLK0B SSPOUT0B SSPIN0 ENABLE SSPCLK0B SSPOUT0B SSPIN0 (XIO14) HRST WAIT WAIT (XIO12) J11 TOP VIEW BACK-END CONNECTOR FOR SANYO DRIVE R142 10k N/A R141 10k N/A ENABLE P1 SSPCLK0B P1 SSPOUT0B P1 SSPIN0 P1 R100 10k The reset signal for DVD Drive is activ HIGH WAIT P1 P1 DRVRST- R99 4k7 Q6 BC847AL R138 4k7 6 Digital-Platte / Board – SDRAM (P4) P4 V3.3 P1 MD[31:16] P1 MA[13:0] P1 MD[15:0] MD[31:16] MD31 MD30 MD29 MD28 MD27 MD26 MD25 MD24 MD23 MD22 MD21 MD20 MD19 MD18 MD17 MD16 P1 P1 P1 P1 DQM0DQM1DQM2DQM3- C132 100uF 50V U22 MCLK1 P1 MCLK1 MD[15:0] MD15 MD14 MD13 MD12 MD11 MD10 MD9 MD8 MD7 MD6 MD5 MD4 MD3 MD2 MD1 MD0 V3.3 MD1 MD2 V3.3 MD5 MD6 P1 WEMA13 MA12 MA11 MA10 MA9 MA8 MA7 MA6 MA5 MA4 MA3 MA2 MA1 MA0 MD0 MD3 MD4 P1 CKE MA[13:0] V3.3 MD7 P1 CASP1 RAS- DQM0- V3.3 WECASRASCS0- P1 CS0- MA13 MCLK1 TS20 TS21 GND C128 C135 C130 C133 0.1uF 0.1uF 0.1uF 0.1uF MA12 MA10 MA0 MA1 MA2 DQM3- MCLK1 R133 0R N 1 0 9 6 7900 For 32MB fit R135 For 64MB fit R133 R135 0R N/A V3.3 MD24 MD25 MD26 MD27 MD28 V3.3 MD29 MD30 MD31 V3.3 V3.3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 VCC DQ0 VCCQ DQ1 DQ2 VSSQ DQ3 DQ4 VCCQ DQ5 DQ6 VSSQ DQ7 NC VCC DQM0 WE CAS RAS CS NC BA0 BA1 A10/AP A0 A1 A2 DQM2 VCC NC DQ16 VSSQ DQ17 DQ18 VCCQ DQ19 DQ20 VSSQ DQ21 DQ22 VCCQ DQ23 VCC VSS DQ15 VSSQ DQ14 DQ13 VCCQ DQ12 DQ11 VSSQ DQ10 DQ9 VCCQ DQ8 NC VSS DQM1 NC NC CLK CKE A9 A8 A7 A6 A5 A4 A3 DQM3 VSS NC DQ31 VCCQ DQ30 DQ29 VSSQ DQ28 DQ27 VCCQ DQ26 DQ25 VSSQ DQ24 VSS 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 MD8 MD9 MD10 V3.3 MD11 MD12 MD13 MD14 V3.3 MD15 DQM1MCLK1 CKE MA9 MA8 MA7 MA6 MA5 MA4 MA3 DQM2MD16 V3.3 MD17 MD18 MD19 MD20 V3.3 MD21 MD22 MD23 SDRAM 64 Mbit (2M x32) Samsung KS643232E NDV8501: F=94.5MHz NDV8601: F=125MHz October 16, 2001 Rev 0.04 GRUNDIG Service 3 - 15 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Digital-Platte / Board – FLASH (P5) P5 Notes: Recommended latch type for 3.3V is 74LCX573. Recommended FLASH speed grade is 90ns or faster. 3 D3 LA[0:19] LA0 LA1 LA2 LA3 SRSTB- P1 1 R41 10K 2 R68 10K BAT54A LA0 LA1 LA2 LA3 TP1 TEST POINT SMD PWE0 - PWE 0- P1, P6 V3.3 RDR107 10k TEST POINT SMD 74LCX573AMTC FLLATCHOE R22 0R 0R R96 LA4 LA5 LA6 LA7 LA8 LA9 LA10 LA11 0R N/A 20 19 18 17 16 15 14 13 12 11 LA16 C121 0.1UF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 LA19 TP3 TEST POINT SMD V3.3 U15 LA15 LA14 LA13 LA12 LA11 LA10 LA9 LA8 R93 OE VCC D1 Q1 Q2 D2 D3 Q3 D4 Q4 Q5 D5 Q6 D6 Q7 D7 D8 Q8 GND LE R89 1 2 3 4 5 6 7 8 9 10 U12 1 2 3 4 5 6 7 8 9 10 AD12 AD13 AD14 AD15 AD16 AD17 AD18 AD19 R37 330R OE VCC Q1 D1 Q2 D2 Q3 D3 Q4 D4 Q5 D5 Q6 D6 Q7 D7 Q8 D8 GND LE 20 19 18 17 16 15 14 13 12 11 LA12 LA13 LA14 LA15 LA16 LA17 LA18 LA19 LA18 LA17 LA7 LA6 LA5 LA4 LA3 LA2 LA1 ALE P1, P6 74LCX573AMTC LA0 C117 0.1UF A15 A16 A14 BYTE A13 VSS A12 DQ15/A-1 A11 DQ7 A10 DQ14 A9 DQ6 A8 DQ13 NC DQ5 NC DQ12 WE DQ4 RESET VCC NC DQ11 WP DQ3 RY/BY DQ10 A18 DQ2 A17 DQ9 A7 DQ1 DQ8 A6 DQ0 A5 OE A4 VSS A3 A2 CE A1 A0 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 C122 0.1UF Flash AM29F800 8mbit TSOP48_0 AD[31:0] R95 10K TP4 U14 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 RD- P1, P6 V3.3 V3.3 FLTSOPCS0- V3.3 0R LA[3:0] P1, P6 FLASHCS0- FLASHCS0- P6 V3.3 AD15 AD7 AD14 AD6 AD13 AD5 AD12 AD4 AD[31:0] P1, P6 AD11 AD3 AD10 AD2 AD9 AD1 AD8 AD0 C123 47uF 50V October 16, 2001 Rev 0.04 Digital-Platte / Board – Interface (P6) AD[31:0] P1, P5 POWER-UP CONFIGURATION RESISTORS R75 3k3 AD4 R73 3k3 N/A AD14 MANUFACTURER: AMP PN: 179030-4 100PIN, 0.8MM PITCH Setting: allows selection of 16/32 bit mode for ROM. Pulldown resistor R75 fitted ==> 0 = 16-bits Pulldown resistor R75 not fitted ==> 1 = 32-bits Setting hardware to specify power up strategy to software. AD14] --> cfg_PdnMd PWR_CFG[10] R/W cfg_PdnMd = ~AD[14] R73 fitted 0 = Power down option 1* R73 not fitted 1 = Power down option 2 TS14 TS16 TS18 TS19 AD30 AD28 AD26 AD24 AD23 AD22 AD21 AD19 AD17 AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD8 AD7 AD6 AD5 AD3 AD1 Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 PWE 0LA0 LA2 JUMPER SETTING RD- R85 SW DEVELOPMENT (SRAM) LHLD R86 PRODUCTION (FLASH) P5 FLASHCS0- R85 0R N/A FLASHCS0- SRAMCSXIO3 R86 0R PCS0XIO5 XIO7 XIO9 XIO11 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 +5V +5V +3.3V +3.3V SPARE1 SPARE2 GND AD30 AD28 AD26 AD24 AD23 AD22 AD21 AD19 AD17 AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD8 AD7 AD6 AD5 AD3 AD1 GND PWE0GND LA0 LA2 GND RDGND LHLD GND SRAMCSGND XIO3 GND XIO5 GND XIO7 GND XIO9 GND XIO11 +5V +5V +3.3V +3.3V SRSTRSTPGND AD31 AD29 AD27 AD25 GND PWE3GND AD20 AD18 GND PWE2GND SCLK GND ACKGND AD9 GND PWE1GND AD4 AD2 AD0 GND ALE GND LA1 LA3 GND LHLDA GND PCS0GND XIO1 GND XIO4 GND XIO6 GND XIO8 GND XIO10 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 SRST- P6 TS15 TS17 SRST- P1, P2 RSTP-FPGA- P1 AD31 AD29 AD27 AD25 PWE3 AD20 AD18 PWE2 SCLKR LA[3:0] ACKAD9 PWE1 AD4 AD2 AD0 ALE LA1 LA3 LHLDA LA[3:0] P1, P5 LA3 LA2 LA1 LA0 PWE3 PWE2 PWE1 PWE0 - SCLKR ACK- PWE3 PWE2 PWE1 PWE0 - P1 P1 P1 P1, P5 SCLKR P1 ACK- P1 PCS0XIO1 ALE XIO4 LHLDA XIO6 LHLD ALE P1, P5 LHLDA P1 LHLD P1 XIO8 RDXIO10 PCS0- RD- P1, P5 PCS0- P1 CONN 50X2 BOARD TO BOARD 0. 8MM AMP 179030- 4 (Dev) THIS CONNECTOR (XBUS) IS USED FOR SW DEVELOPMENT, FLASH PROGRAMMING, AND CONNECTING WITH OTH ER HW DEVELOPMENT PLATFORMS AND LOGIC ANALYZER. J12 XIO[1:11] October 16, 2001 Rev 0.04 3 - 16 GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Bedieneinheit / Keyboard Control Ansicht von der Bestückungsseite / View of Component Side 30 20 10 0 270 260 250 POS. X Y C1 C3 IR1 J1 LED1 SW1 SW2 SW3 SW4 46 140 72 38 113 203 223 248 183 5 23 8 4 8 28 28 28 28 240 230 220 210 200 190 180 60 70 80 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 Y X Ansicht von der Lötseite / View of Solder Side 30 20 10 Y 0 X 0 10 20 30 40 50 POS. X Y POS. X Y POS. X Y POS. X Y POS. C2 C4 C5 C6 C7 42 40 37 35 32 21 11 11 11 11 LK1 LK2 LK3 LK4 27 27 30 30 17 22 17 22 LK7 LK8 LK9 42 61 42 11 9 16 LK13 LK14 100 103 25 28 LK15 LK16 LK17 103 57 47 23 6 15 6 25 23 28 9 9 9 9 9 50 93 95 95 145 127 132 149 136 D1 LK10 LK11 LK12 Q1 Q2 Q3 Q4 Q5 Q6 154 9 GRUNDIG Service LK5 LK6 20 27 17 11 X Y 90 POS. Q7 Q8 Q9 Q10 Q11 Q12 100 110 120 130 140 150 160 170 180 190 200 210 220 X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y 140 59 69 54 9 20 19 20 Q13 Q14 49 80 20 18 R5 150 15 24 24 24 24 22 16 16 28 28 R35 104 13 15 15 15 24 24 50 66 76 56 110 105 138 154 141 58 68 R17 R18 R19 R20 R29 R30 R6 R7 R8 R9 R10 24 24 24 24 23 108 40 37 6 15 15 15 53 73 63 48 78 R23 R24 R25 54 146 132 135 R11 R12 R13 R14 R15 R31 R32 R33 R34 98 58 84 53 28 15 15 15 15 15 13 23 16 16 28 62 50 107 81 35 32 113 R36 R37 R38 R16 R26 R27 R28 U1 121 21 75 64 19 20 R1 R2 R3 R4 3 - 17 R21 R22 71 61 GRUNDIG Service 24 24 230 240 250 260 270 3 - 18 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Bedieneinheit / Keyboard Control LED1 LED 5x7 + Icons S1 S2 S3 S4 S5 S6 S7 G7 G6 G5 G4 G3 G2 B E G C F D A s :(1) :(2) || VCD DVD g B E G C F D A B E G C F D A B E G C F D A B E G C F D A G1 DISK MP3 CD • DIG1 DIG7 DIG2 DIG3 DIG4 DIG5 DIG6 0V Vs 3.3V_STBY 1 2 3 17 IR 16 15 G F 9 E 6 D 11 C 4 B 8 A 13 1 6 7 3 5 14 3 4 12 10 2 7 5 2 1 IR1 IR Receiver R1 100R 5V 40 39 10R R32 Q2 G7 R3 1k FNNT- 491A Q8 Q5 R6 1k FNNT- 491A 10k R9 5V 10R R33 G5 C1 47UF 16V BC847B BC847B 10k R10 Q9 5V Q7 R8 1k FNNT- 491A G4 10R R34 BC847B Q1 R2 1k FNNT- 491A G3 10k R11 Q10 5V 10R R35 BC847B 10k R12 Q11 Q4 R5 1k FNNT- 491A G2 5V 10R R36 BC847B Q6 R7 1k FNNT- 491A G1 10k R13 Q12 5V Q3 R4 1k FNNT- 491A G6 10R R37 BC847B 10k R14 Q13 5V Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 10R R38 BC847B G[1:7] 10k R15 1k 1k 1k 1k 1k 1k S7 R16 S1 R17 S4 R18 S6 R19 S2 R20 S5 R21 S3 R22 1k G5 G6 G7 Q14 5V C2 0.1UF 10% R23 47K 5V 5V GRID4 GRID3 GRID2 GRID1 VDD LED4 LED3 LED2 LED1 VSS OSC UPD16312 OD SEG8 SEG7 SEG6/KS6 SEG5/KS5 SEG4/KS4 SEG3/KS3 SEG2/KS2 SEG1/KS1 VDD KEY4 KEY3 S6 22 21 20 19 18 17 16 15 14 13 12 5V S7 S6 S5 S4 S3 S2 S1 5V C3 47UF 16V SW1 PLAY SW2 1 2 3 4 5 6 7 8 9 10 11 5V 34 35 36 37 38 39 40 41 42 43 44 SW1 SW2 SW3 SW4 DOUT DIN VSS CLK STB KEY1 KEY2 G4 G3 G2 G1 D1 BAV70/SOT U1 GRID5 GRID6 SEG16/GRID7 SEG15/GRID8 SEG14/GRID9 SEG13/GRID10 VEE SEG12/GRID11 SEG11 SEG10 SEG9 33 32 31 30 29 28 27 26 25 24 23 S[1:7] 24 25 26 J1 1->n 3.3V_STBY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DOUT DIN CLK STB CS WAKEUP- R24 10K R25 10K R26 10K R27 10K SW3 CLK STB 23 STOP 5V DOUT DIN 22 POWER SW4 C4 100PF C5 100PF C6 100PF C7 100PF EJECT R28 4K7 R29 4K7 R30 4K7 R31 4K7 TO Digital Board – P2 Connector J6 3 - 19 October 11, 2001 GRUNDIG Service 3 - 20 GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Laufwerk-Platte / Drive Board SMD-Bestückung der Oberseite – Ansicht von der Bestückungsseite / SMD Assembly of the Upper Side – View of the Component Side 80 70 70 60 60 50 50 40 40 30 30 20 20 10 10 0 90 80 70 60 50 40 30 0 10 Y Y X 0 X POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. Y POS. X Y POS. X Y POS. X Y POS. X C1103 C1104 C1105 C1106 C1115 73 85 38 88 78 69 60 41 72 74 C1425 C1426 53 66 34 48 20 58 D1101 D1102 82 85 65 65 Q5020 5 75 C1117 C1118 C1120 C1122 C1128 80 92 89 93 66 69 72 71 59 70 74 74 65 71 50 C1129 C1130 C1131 C1132 C1133 73 61 61 59 55 71 61 64 65 66 54 57 41 54 38 C1134 C1135 C1136 C1137 C1138 48 51 45 45 41 61 61 56 54 45 L1002 L1003 L1004 L1005 L1006 75 40 55 85 91 75 65 70 72 66 49 53 39 42 32 L2002 L2003 L9001 72 37 84 27 19 18 31 41 32 39 62 CAN1 CAN2 CAN20 CAN3 CAN7 44 66 40 15 18 68 67 20 37 69 C1150 C1151 C1152 C1153 C1418 66 63 42 71 64 57 61 36 45 38 C1420 C1422 C1424 59 67 55 59 67 33 C6003 C6004 C6005 36 10 12 32 14 17 44 27 79 17 63 59 70 62 63 59 R2414 61 13 3 7 3 7 57 62 60 63 63 68 66 66 68 68 7 9 16 20 9 R1040 R2452 R2453 R2454 R2455 R5020 R5021 R5022 R5023 R5024 72 54 57 39 34 15 13 13 10 13 81 66 68 81 51 71 66 65 63 63 Q1018 R1187 R1188 R1189 R1190 R2409 R2410 R2411 R2412 R2413 7 3 7 3 7 4 95 64 93 70 69 76 78 69 60 62 62 64 64 CN610 CN620 CN630 CN900 R1033 R1034 R1035 R1038 R1039 R2447 R2448 R2449 R2450 R2451 22 56 59 57 61 37 51 66 66 69 31 30 41 59 40 29 16 8 16 9 54 81 79 76 81 47 45 55 65 51 R5015 R5016 R5017 R5018 R5019 Q1012 Q1013 Q1015 Q1016 Q1017 R1182 R1183 R1184 R1185 R1186 25 59 56 15 17 43 12 11 25 26 29 36 21 23 31 37 57 56 68 70 31 64 71 75 75 34 29 20 29 27 R2020 R2040 R2084 R2407 R2408 C2207 C2208 C2209 C2210 C2211 C5206 C5207 C5208 C6001 C6002 59 4 4 46 19 72 72 72 66 66 3 7 3 7 3 92 59 33 93 2 79 77 76 72 70 56 56 58 58 60 CN100 CN200 CN500 CN540 CN600 R1028 R1029 R1030 R1031 R1032 R2442 R2443 R2444 R2445 R2446 56 51 52 58 54 63 72 58 41 44 51 39 40 37 40 7 16 16 16 16 76 70 40 44 67 39 41 48 51 53 R5009 R5011 R5012 R5013 R5014 Q1007 Q1008 Q1009 Q1010 Q1011 R1174 R1176 R1179 R1180 R1181 33 31 28 9 10 63 63 63 63 63 71 15 15 41 44 29 29 40 45 48 50 48 46 43 42 2 12 35 31 19 R2015 R2016 R2017 R2018 R2019 C2201 C2202 C2203 C2205 C2206 C5021 C5031 C5200 C5203 C5205 60 67 70 64 69 7 3 7 3 7 51 57 61 78 61 75 77 77 79 79 50 52 52 54 54 C1144 C1145 C1146 C1148 C1149 R1023 R1024 R1025 R1026 R1027 R2437 R2438 R2439 R2440 R2441 54 49 51 53 54 54 68 69 71 63 58 58 51 51 46 5 16 7 7 7 36 70 83 86 73 46 44 46 42 48 R5004 R5005 R5006 R5007 R5008 Q1002 Q1003 Q1004 Q1005 Q1006 R1168 R1169 R1170 R1171 R1172 58 58 58 58 34 54 31 25 21 63 41 68 74 74 66 38 40 41 42 29 54 67 45 40 51 20 17 17 20 5 R2010 R2011 R2012 R2013 R2014 C2090 C2099 C2157 C2184 C2200 C5001 C5002 C5003 C5004 C5020 75 72 60 60 60 35 35 3 7 3 46 40 49 53 48 86 82 70 72 73 78 80 49 49 50 C1139 C1140 C1141 C1142 C1143 R1018 R1019 R1020 R1021 R1022 R2431 R2432 R2434 R2435 R2436 43 61 48 49 56 13 77 66 16 16 13 69 66 63 58 60 32 4 16 7 5 85 65 49 17 19 79 61 57 61 48 50 R2473 R5000 R5001 R5002 R5003 C9003 C9004 C9005 C9006 C9008 C9909 R1163 R1164 R1165 R1166 R1167 53 57 58 58 58 59 54 58 54 47 11 25 20 46 35 47 46 44 35 37 55 50 54 56 73 42 29 29 32 22 R2004 R2006 R2007 R2008 R2009 C2020 C2021 C2022 C2083 C2087 C2439 C2440 C2441 C2442 C5000 41 42 36 43 51 20 18 35 35 35 43 20 54 21 21 58 69 58 63 37 34 34 74 75 77 29 71 52 73 36 R1013 R1014 R1015 R1016 R1017 R2426 R2427 R2428 R2429 R2430 R2463 R2466 R2470 R2471 R2472 37 27 17 28 38 63 61 61 61 63 45 73 58 57 57 72 33 24 78 93 67 64 59 57 56 72 91 50 49 47 C6565 C6570 C6900 C9000 C9001 R1157 R1159 R1160 R1161 R1162 R1197 R1199 R2001 R2002 R2003 40 39 53 53 53 16 11 16 16 14 43 36 42 42 44 84 84 66 59 58 61 60 60 58 43 R1008 R1009 R1010 R1011 R1012 C1439 C1440 C1441 C2001 C2002 C2434 C2435 C2436 C2437 C2438 64 26 31 41 22 30 16 13 16 18 23 7 3 7 11 14 5 34 22 79 20 81 57 57 41 42 34 70 72 72 55 54 IC502 IC504 IC550 IC601 IC602 IC900 R2419 R2422 R2423 R2424 R2425 R2457 R2458 R2459 R2460 R2461 18 28 30 54 46 54 53 69 74 67 54 53 54 36 54 29 88 72 90 75 69 69 79 89 66 63 62 69 45 65 C6542 C6545 C6560 C6562 C6563 R1132 R1133 R1137 R1141 R1156 R1192 R1193 R1194 R1195 R1196 74 55 66 63 52 21 17 14 12 16 86 82 69 68 43 71 47 36 65 73 77 71 68 68 63 R1003 R1004 R1005 R1006 R1007 C1434 C1435 C1436 C1437 C1438 C2217 C2218 C2431 C2432 C2433 51 45 34 21 56 11 10 13 14 3 57 80 55 61 20 54 58 58 55 70 IC100 IC101 IC200 IC201 IC500 R2415 R2416 R2417 R2418 R2456 54 21 17 7 22 62 49 39 50 59 78 27 34 33 36 57 75 80 78 61 C6008 C6009 C6011 C6012 C6503 R1110 R1125 R1126 R1128 R1191 45 41 70 68 53 28 29 31 16 18 12 82 69 40 54 50 72 75 75 75 47 43 C6006 C6007 C1427 C1428 C1429 C1430 C1433 C2212 C2213 C2214 C2215 C2216 R5025 9 65 GRUNDIG Service X 20 SMD Bestückung der Unterseite – Ansicht von der Lötseite / SMD Assembly of the Lower Side – View of the Solder Side 80 3 - 21 Y 0 10 20 30 40 50 60 70 90 80 POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y POS. X Y R5026 R5027 R5028 R5029 9 11 12 13 66 68 68 68 R5202 41 10 43 R5030 R5032 R5033 R5034 R5035 17 13 18 20 26 68 68 65 68 71 X2000 X5000 39 19 14 79 R5269 32 50 TP101 TP102 TP103 TP104 55 63 69 49 38 58 59 42 TP208 41 55 TP248 TP249 TP250 TP251 48 46 62 44 64 64 45 64 50 52 54 56 55 76 60 58 56 54 48 43 21 18 36 34 34 34 32 7 29 29 29 29 7 14 8 8 TP534 TP535 TP536 TP537 TP538 TP577 TP580 TP581 TP582 TP583 R5063 R5066 R5067 R5068 63 61 61 55 52 12 10 12 60 60 30 25 2 45 27 52 54 40 44 44 53 53 55 52 49 7 14 45 28 83 TP203 TP204 TP205 TP206 TP207 TP243 TP244 TP245 TP246 TP247 TP626 TP627 TP700 TP701 TP702 58 56 54 53 51 70 35 28 44 18 38 38 47 47 50 33 33 33 32 32 60 71 31 73 85 33 35 27 32 33 R5264 R5265 R5266 R5267 R5268 R6569 R6573 R6574 R6575 R9999 TP529 TP530 TP531 TP532 TP533 6 3 65 63 61 43 43 44 45 46 74 66 63 73 52 40 40 11 16 10 16 13 12 7 7 95 79 94 89 69 TP572 TP573 TP574 TP575 TP576 R5058 R5059 R5060 R5061 R5062 TP145 TP146 TP147 TP148 TP201 5 56 53 6 12 30 27 71 12 17 66 64 63 61 59 76 59 9 46 51 8 7 65 13 12 32 32 32 33 32 TP238 TP239 TP240 TP241 TP242 TP620 TP621 TP623 TP624 TP625 R5259 R5260 R5261 R5262 R5263 43 54 55 52 72 66 65 63 65 40 9 26 63 2 4 75 86 88 88 61 33 36 24 24 32 22 29 14 43 42 R6564 R6565 R6566 R6567 R6568 TP524 TP525 TP526 TP527 TP528 TP562 TP564 TP566 TP570 TP571 44 44 44 44 44 59 64 66 74 49 10 10 12 2 3 25 23 22 20 18 78 84 81 81 67 58 60 60 75 73 R5053 R5054 R5055 R5056 R5057 TP140 TP141 TP142 TP143 TP144 TP233 TP234 TP235 TP236 TP237 43 36 34 26 35 43 43 43 43 43 33 41 48 48 33 2 9 8 12 7 20 21 23 24 26 71 73 71 72 87 TP615 TP616 TP617 TP618 TP619 R5254 R5255 R5256 R5257 R5258 R6509 R6526 R6527 R6528 R6562 60 62 63 63 65 1 3 3 6 9 56 55 52 52 52 38 33 30 27 29 48 25 23 24 24 24 24 25 23 22 TP516 TP520 TP521 TP522 TP523 TP557 TP558 TP559 TP560 TP561 R5047 R5048 R5050 R5051 R5052 57 58 60 60 62 16 60 44 10 12 51 28 48 45 38 74 78 82 74 77 54 41 45 55 58 71 10 2 2 10 TP135 TP136 TP137 TP138 TP139 TP226 TP229 TP230 TP231 TP232 TP610 TP611 TP612 TP613 TP614 23 21 43 43 43 34 49 33 52 34 65 65 65 69 72 9 9 15 17 18 4 9 17 87 73 13 15 21 23 25 R5223 R5224 R5251 R5252 R5253 R6016 R6017 R6020 R6507 R6508 TP511 TP512 TP513 TP514 TP515 48 57 50 52 6 71 62 60 59 57 76 54 53 57 55 10 7 11 11 42 30 24 24 24 24 88 81 76 79 78 TP552 TP553 TP554 TP555 TP556 R5041 R5043 R5044 R5045 R5046 TP124 TP130 TP131 TP133 TP134 29 26 24 28 16 21 24 37 34 56 3 10 27 10 74 30 34 32 36 55 29 28 69 44 81 33 33 32 40 2 TP218 TP219 TP220 TP221 TP225 TP604 TP605 TP607 TP608 TP609 R5214 R5215 R5216 R5221 R5222 26 15 15 15 15 51 54 56 58 63 22 17 49 43 45 29 27 29 30 32 9 7 20 13 11 25 35 34 9 11 R6011 R6012 R6013 R6014 R6015 TP505 TP507 TP508 TP509 TP510 TP544 TP545 TP549 TP550 TP551 71 60 60 60 71 67 41 61 33 76 34 35 32 33 31 27 19 20 22 29 59 68 60 56 81 36 33 36 33 33 R5036 R5037 R5038 R5039 R5040 TP114 TP118 TP119 TP121 TP122 TP213 TP214 TP215 TP216 TP217 49 50 57 40 30 10 10 10 10 10 44 44 44 18 28 90 88 87 74 84 30 28 27 26 24 30 29 26 28 28 TP589 TP590 TP601 TP602 TP603 R5209 R5210 R5211 R5212 R5213 R5274 R5275 R5276 R6009 R6010 53 53 51 10 47 59 22 22 20 51 40 36 38 70 12 34 19 22 25 85 TP253 TP254 TP256 TP257 TP501 TP540 TP541 TP542 TP543 TP588 34 57 68 62 66 55 55 36 36 64 48 60 26 45 57 39 36 36 30 41 TP106 TP107 TP109 TP111 TP113 TP209 TP210 TP211 TP212 TP252 10 10 10 10 10 48 46 44 44 47 38 37 36 34 31 32 32 33 32 TP105 R5203 R5204 R5205 R5206 R5208 R5270 R5271 R5272 R5273 TP539 32 57 TP584 TP585 TP586 TP587 29 28 20 24 52 50 50 49 GRUNDIG Service 3 - 22 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… Laufwerk-Platte / Drive Board To Digital Board P1, Connector J15 Reference IC Block Diagrams ..... 3-3 Oscillograms ............ 3-29 Digital Board – P1 ........................... 3-11 – P2 .......................... 3-13 – P3 ........................... 3-15 – P4 ........................... 3-15 – P5 ........................... 3-16 – P6 ........................... 3-16 Drive Board ................ 3-23 Keyboard Control ....... 3-19 Power Supply ............... 3-8 To Digital Board P3, Connector J10 21 20 19 18 17 62 63 To Digital Board P3, Connector J11 7 8 10 12 14 16 9 11 13 15 61 60 59 3 - 23 GRUNDIG Service 3 - 24 GRUNDIG Service Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams 3 - 25 Livance – GDP 31… GRUNDIG Service 59 3 - 26 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams 60 Livance – GDP 31… Laufwerk-Platte / Drive Board (vergrößert / enlarged) GRUNDIG Service 62 63 61 7 10 16 15 14 13 12 9 8 11 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams 3 - 28 To Digital Board P3, Connector J11 Livance – GDP 31… GRUNDIG Service 17 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams 3 - 27 To Digital Board P1, Connector J15 To Digital Board P3, Connector J10 20 21 19 18 Livance – GDP 31… GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Oszillogramme / Oscillograms power on 1 Mode: DVD playback power on 5 Mode: switch power on 2 Mode: DVD playback power on 6 Mode: switch power on 3 Mode: DVD playback 4 Mode: switch power on power on 7 Mode: switch power on 8 Mode: DVD playback 9 Mode: DVD playback 0 Mode: DVD playback ! Mode: DVD playback @ Mode: CD stop # Mode: CD playback $ Mode: CD playback % Mode: CD playback ^ Mode: CD playback power on & Mode: DVD playback * Mode: DVD playback ( Mode: switch power on ) Mode: DVD playback ¡ Mode: DVD playback ™ £ ≤ GRUNDIG Service Mode: DVD playback Mode: DVD playback Mode: DVD playback 3 - 29 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Livance – GDP 31… ∞ Mode: DVD playback § Remote Control signal ≥ ª Mode: DVD playback º ⁄ Mode: DVD playback ¤ Mode: DVD playback Mode: DVD playback Mode: DVD playback • Mode: DVD playback ‹ Mode: DVD playback › Mode: DVD playback fi Mode: DVD playback fl Mode: DVD playback, 1kHz/0dB ‡ ° · Mode: DVD playback ‚ Mode: DVD playback ľɨ Mode: DVD playback ľ˳ Mode: DVD playback Mode: DVD playback, 1kHz/0dB ıy Mode: DVD playback ľu Mode: DVD playback 3 - 30 ľm Mode: DVD playback 1kHz/0dB Mode: DVD playback GRUNDIG Service Livance – GDP 31… Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams Steckerübersicht / Connection Overview Digital-Platte / Board Socket J15 to DVD Drive (Power Supply) Socket J1 to Power Supply Pin 1 2 3 4 5 6 7 8 9 10 11 Level (ca.) +3.3V +3.3V 0V 0V 0V 0V 0V +5V +15V +12V +30V Name +3.3V +3.3V GND GND GND GND GND +5.0V +15V +12V +30V Description +3.3 Volts out +3.3 Volts out Digital Ground Digital Ground Analogue Ground Analogue Ground Drive Ground +5 Volts out +15 Volts out +12 Volts out +30 Volts out Socket J6 to J7 (Keyboard Control) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Level (ca.) 0V Name GND Description Ground 0V GND Ground +5V +12V +30V +3.3V +5.0V +12V +30V V3.3 +5 Volts out +12 Volts out +30 Volts out +3.3 Volts out +3.3V +5V +5V +5V +3.3V 0V IRIN FLD_CS FPDCLK FPDOUT FPDIN GND Remote control data In FLD chip select Clock Data Out Data In Ground Pin 1 2 3 4 5 6 Level (ca.) +5V 0V +5V 0V +9V 0V Name +5.0V GND +5.0V GND +9V GND Description +5 Volts out Ground +5 Volts out Ground +9 Volts out Ground Socket J5 (TV SCART) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Level (ca.) 6.25VPP Name TV_AOR Description Audio Out Right 6.25VPP 0V 0V TV_AOL GND GND Audio Out Left Ground Ground TV_BLUE_O TV_PIN8 GND No Function TV_GREEN_O No Function GND GND TV_RED_O TV_PIN16_O GND GND TV_CVBS_O BLUE Out Control Ground Ground Ground RED Out Fast Blank Ground Ground Composite Video Out GND Ground 700mV +6/+12V 0V TST_CLK 700mV TST_DATA 0V 0V 700mV +3.3V 0V 0V 1VPP 0V GREEN Out Socket J10 to DVD Drive Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Level (ca.) +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V Name DVD7 GND DVD6 GND DVD5 GND DVD4 GND DVD3 GND DVD2 GND DVD1 GND DVD0-FE GND DREQ GND DACK-FE GND DERR GND DSYNC GND DCLK-FE GND Description Data Bit Ground Data Bit Ground Data Bit Ground Data Bit Ground Data Bit Ground Data Bit Ground Data Bit Ground Control Ground Control Ground Control Ground Control Ground Control Ground Control Ground Socket J11 to DVD Drive Pin 1 2 3 4 5 6 7 8 10 12 13 14 15 16 Level (ca.) +5V +5V 0V +5V +5V +5V +5V 0V 0V +5V +5V +5V +5V +5V GRUNDIG Service Name WAIT HRST GND SSPIN0 SSPOUT0B SSPCLK0B ENABLE GND GND C2PO LRCK-FE BCK-FE CDDA-FE FE-SPDIF Socket J3 (AUDIO OUT) Pin 1 2 3 4 5 Level (ca.) 0V AOR AOL 0V 1.8V Name GND Audio Out Right Audio Out Left SPDIF_GND SPDIF_COAX_O Description Ground Ground Digital Audio Out Bedieneinheit / Keyboard Control Socket J7 to J6 (Digital Board) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Level (ca.) 0V +3.3V +5V +5V +5V +3.3V Name GND DOUT DIN CLK FLD_CS IRIN Description Ground Data Out Data In Clock FLD chip select Remote control data In +3.3V +30V +12V +5V V3.3 +30V +12V +5.0V +3.3 Volts out +30 Volts out +12 Volts out +5 Volts out 0V GND Ground 0V GND Ground Description Control Control Ground Control Control Control Control Ground Ground Control Control Control Control Control 3 - 31 Platinenabbildungen und Schaltpläne / Layout of PCBs and Circuit Diagrams 3 - 32 Livance – GDP 31… GRUNDIG Service Explosionszeichnungen und Ersatzteillisten / Exploded Views and Spare Parts Lists Livance – GDP 31… Explosionszeichnungen und Ersatzteillisten Exploded Views and Spare Parts Lists DM01 1 DM02 DM04 DM03 DM04 DM05 DM07 DM06 DM13 DM14 DM15 DM08 DM09 DM10 DM17 DM16 DM11 DM12 DM44 DM18 DM45 DM22 DM19 DM46 DM20 DM21 DM24 DM30 DM31 DM32 DM33 DM25 DM26 DM23 DM39 DM40 DM34 DM35 DM27 DM28 DM29 DM39 DM40 DM36 DM37 DM39 DM40 DM38 DM39 DM40 DM41 DM41 DM42 DM43 GRUNDIG Service 4-1 7 14 7 8 9 5 5 6 5 12 3 9 5 9 20 5 19 1 5 10 18 16 15 5 5 2 13 5 21 17 4 5 5 11 Livance – GDP 31… 9 GRUNDIG Service 8 5 Explosionszeichnungen und Ersatzteillisten / Exploded Views and Spare Parts Lists 4-2 2 6 5 5 Ersatzteilliste Spare Parts List DVD LIVANCE GDP 3100 10 / 2001 Ersatzteilliste Spare Parts List DVD LIVANCE GDP 3105 12 / 2001 MATERIAL-NR. / PART NO.: 926710151001 BESTELL-NR. / ORDER NO.: GMI9800 MATERIAL-NR. / PART NO.: 926710150801 BESTELL-NR. / ORDER NO.: GMI9400 POS. NR. ABB. POS. NO. FIG. DESCRIPTION POS. NR. ABB. POS. NO. FIG. MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG 926710151001 LIVANCE GDP 3105 KEIN E-TEIL LIVANCE GDP 3105 NO SPARE PART GEH.-OBERTEIL FRONTBLENDE KPL SILBER FUSS GUMMI TOP COVER FRONT PANEL SILVER RUBBER FEET MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG 926710150801 LIVANCE GDP 3100 KEIN E-TEIL LIVANCE GDP 3100 NO SPARE PART GEH.-OBERTEIL FRONTBLENDE KPL SILBER FUSS GUMMI TOP COVER FRONT PANEL SILVER RUBBER FEET 0001.000 0004.000 0009.000 2 2 2 267210030101 267120300101 267160020001 4 d © DESCRIPTION d © 2 2 2 267210030101 267120300001 267160020001 4 0010.000 2 267275000402 X LAUFWERK KIT510LE KEIN E-TEIL DRIVE MECHANISM KIT510LE NO SPARE PART 0010.000 2 267275000402 X LAUFWERK KIT510LE KEIN E-TEIL DRIVE MECHANISM KIT510LE NO SPARE PART 0011.000 2 0012.000S 2 267290760101 267270150101 X X DIGITALPLATTE NETZTEILPLATTE DVD PSSH37060B DIGITAL BOARD POWER SUPPLY PSSH370603B 0011.000 2 0012.000S 2 267290860101 267270150101 X X DIGITALPLATTE NETZTEILPLATTE DVD PSSH37060B DIGITAL BOARD POWER SUPPLY PSSH370603B 0014.000 2 267290810501 X BEDIENPLATTE KPL KEIN E-TEIL CONTROL BOARD ASSY NO SPARE PART 0014.000 2 267290810501 X BEDIENPLATTE KPL KEIN E-TEIL CONTROL BOARD ASSY NO SPARE PART 0015.000 2 0017.000 2 0018.000 2 0021.000 2 0022.000 2 0023.000 2 0027.000 S 0028.000 267170080102 267260320002 267260330002 267260350001 267140100201 267130130002 829099122000 267280120201 ABDECKUNG SCHUBLADE FLEX.FOLIENLTG.26-POL FLEX.FOLIENLTG.6-POL FLEX.FOLIENLTG.16-POL TASTENLEISTE LINKS FENSTER NETZKABEL KPL TP81D FERNBEDIENUNG DRAWER COVER FLEXIBLE CABLE 26P FLEXIBLE CABLE 6P FLEXIBLE CABLE 16P BUTTON SET LEFT WINDOW POWER CABLE CPL TP 81D REMOTE CONTROL 0015.000 2 0017.000 2 0018.000 2 0021.000 2 0022.000 2 0023.000 2 0027.000 S 0028.000 267170080003 267260320002 267260330002 267260350001 267140100301 267130130002 829099122000 267280120201 ABDECKUNG SCHUBLADE FLEX.FOLIENLTG.26-POL FLEX.FOLIENLTG.6-POL FLEX.FOLIENLTG.16-POL TASTENLEISTE LINKS FENSTER NETZKABEL KPL TP81D FERNBEDIENUNG DRAWER COVER FLEXIBLE CABLE 26P FLEXIBLE CABLE 6P FLEXIBLE CABLE 16P BUTTON SET LEFT WINDOW POWER CABLE CPL TP 81D REMOTE CONTROL 725990172600 SOFTWARE UPGRADE CD-ROM GDP3100 SOFTWARE UPGRADE CD-ROM GDP3100 725990172700 SOFTWARE UPGRADE CD-ROM GDP3105 SOFTWARE UPGRADE CD-ROM GDP3105 267109415001 267109415101 720105409500 BEDIENUNGSANLEITUNG D/GB/F/I BEDIENUNGSANLEITUNG E/P/DK/S/N SERVICE MANUAL D/GB INSTRUCTION MANUAL D/GB/F/I INSTRUCTION MANUAL E/P/DK/S/N SERVICE MANUAL D/GB 267109415201 720105409500 BEDIENUNGSANLEITUNG D/GB/CS/PL/HU INSTRUCTION MANUAL D/GB/CS/PL/HU SERVICE MANUAL D/GB SERVICE MANUAL D/GB X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LIST X = SIEHE GESONDERTE E-LISTE 4-3 ! (!) The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! ! (!) X = SEE SEPARATE PARTS LIST The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION Explosionszeichnungen und Ersatzteillisten / Exploded Views and Spare Parts Lists 0001.000 0004.000 0009.000 Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! Livance – GDP 31… GRUNDIG Service ǵ ǵ 4-4 Ersatzteilliste Spare Parts List DVD 12 / 2001 LAUFWERK KIT 510 LE DRIVE MECHANISM KIT 510 LE Ersatzteilliste Spare Parts List DVD 11 / 2001 LAUFWERKPLATTE DRIVE BOARD MATERIAL-NR. / PART NO.: 267275000402 POS. NR. ABB. POS. NO. FIG. MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG 267275000402 LAUFWERK KIT 510 LE MIT LAUFWERKPLATTE KEIN E-TEIL DRIVE MECHANISM KIT 510 LE WITH DRIVE MECHANISM BOARD NO SPARE PART LAUFWERKPLATTE KEIN E-TEIL DRIVE BOARD NO SPARE PART RIEMEN LADEMOTOR LP-SCHALTER MODUL SCHUBLADE MECHANIK + LASEREINHEIT SLEDGEMOTOR DAEMPFUNG BELT MOTOR LOADING SWITCH BOARD C.B.A. TRAY MECHANISM+LASERUNIT SLEDGEMOTOR DAMPING X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LIST 759880673400 DM00007 DM00019 DM00020 DM00022 DM00023 DM00038 DM00041 1 1 1 1 1 1 1 759880665400 759880666900 759880671700 759880672400 759880673300 759880670600 759880671200 X DESCRIPTION d ! (!) The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG DESCRIPTION 759880673400 LAUFWERKPLATTE KEIN E-TEIL d © DRIVE BOARD NO SAPRE PART POS. NR. POS. NO. MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION POS. NR. POS. NO. CN 00100 CN 00610 759880659100 759880669200 Q 05020 759880653500 TRANS 2SC2412K-R X 02000 X 05000 759880672200 759880673800 QUARZ 16.9344 MHZ QUARZ 16.0 MHZ SOCKEL 24P FPC SOCKEL 11P FPC D 01101 D 01102 759880673900 759880674000 DIODE KDS120E DIODE DAN222 IC 00100 IC 00101 IC 00200 IC 00201 IC 00500 IC 00502 IC 00504 IC 00550 IC 00601 IC 00602 IC 00900 759880670300 759880659500 759880673600 759880671800 759880673700 759880660800 759880660100 759880673500 759880672000 759880659800 759880661500 IC LA9702WL-MPB IC BU4066BCF IC LC78661W-D IC T224162B-35S IC M37903S4CHP IC M51953BFP IC TC7SHU04FU IC LE28C1001DTS-90-MPB IC BA5937AFP IC BA6849FP IC BA033FP L 01002 L 01003 L 01004 L 01005 L 01006 L 02002 L 02003 L 09001 759880661800 759880661800 759880661800 759880661800 759880661800 759880661800 759880662400 759880672100 SPULE 1000 OHM SPULE 1000 OHM SPULE 1000 OHM SPULE 1000 OHM SPULE 1000 OHM SPULE 1000 OHM SPULE 1000 OHM SPULE 2.2 UH Q 01002 Q 01003 Q 01004 Q 01005 Q 01006 Q 01007 Q 01008 Q 01009 Q 01010 Q 01011 Q 01012 Q 01013 Q 01015 Q 01016 Q 01017 Q 01018 759880653500 759880662300 759880661900 759880661900 759880662300 759880653600 759880662300 759880662300 759880653600 759880662300 830165231800 830236614400 759880662300 759880662300 830165231800 830165231800 TRANS 2SC2412K-R TRANS 2SC1623-L6 TRANS 2SA1036K-R TRANS 2SA1036K-R TRANS 2SC1623-L6 TRANS 2SA1037K-R TRANS 2SC1623-L6 TRANS 2SC1623-L6 TRANS 2SA1037K-R TRANS 2SC1623-L6 SMD TRANS 2SK3018 ROHM SMD TRANS DTC144EKA TRANS 2SC1623-L6 TRANS 2SC1623-L6 SMD TRANS 2SK3018 ROHM SMD TRANS 2SK3018 ROHM Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! ! (!) MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION Livance – GDP 31… GRUNDIG Service Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! © MATERIAL-NR. / PART NO.: 759880673400 POS. NR. ABB. POS. NO. FIG. Explosionszeichnungen und Ersatzteillisten / Exploded Views and Spare Parts Lists ǵ ǵ Ersatzteilliste Spare Parts List DVD 10 / 2001 DIGITALPLATTE DIGITAL BOARD Ersatzteilliste Spare Parts List DVD 12 / 2001 DIGITALPLATTE DIGITAL BOARD MATERIAL-NR. / PART NO.: 267290860101 MATERIAL-NR. / PART NO.: 267290760101 POS. NR. ABB. POS. NO. FIG. MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG DESCRIPTION 267290760101 DIGITALPLATTE DIGITAL BOARD d © MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION POS. NR. POS. NO. MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION D1 D2 D3 D4 D5 D6 D7 D8 D9 D14 832521205300 832521205300 832521205300 830938404700 830938404700 830931309900 830931309900 830931309900 830931309900 830931309900 SMD-DIODE BAT54A SMD-DIODE BAT54A SMD-DIODE BAT54A SMD-Z DIODE BZX 84 C4V7 SMD-Z DIODE BZX 84 C4V7 SMD DIODE BAV99 SMD DIODE BAV99 SMD DIODE BAV99 SMD DIODE BAV99 SMD DIODE BAV99 Q24 Q25 830100784700 830100784700 SMD TRANS BC847 SMD TRANS BC847 RP1 RP4 RP12 877003403700 877003403700 877003403700 SMD R-NETZ 1206 4X33 OHM SMD R-NETZ 1206 4X33 OHM SMD R-NETZ 1206 4X33 OHM FB1 810498233000 SMD DAEMPF-PERLE 0805 BLM J3 J5 812612528900 829017504100 CINCH-BUCHSE 3-FACH LP HS EURO-AV BUCHSENL.21-POL J L3 L4 L5 L6 L7 L10 L11 L12 L13 L14 L15 L17 L21 814052980900 814052980600 814052980600 814052980600 814052980600 814052498400 814052498400 814052981200 814052980600 814052980600 814052980600 814052980600 814052981200 SMD DR 1210 400MA SBY3225 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SIEB-DR 39UH 10% LHL08 T SIEB-DR 39UH 10% LHL08 T SMD DR 10UH 5% 1008NLV25T SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 10UH 5% 1008NLV25T U1 U3 U5 U6 U7 U8 U11 U12 U14 U15 830571543400 830575983400 830497454100 830576111700 830596001600 830477202300 830579125700 830470057300 830470057300 830470980100 U19 U22 830576470900 830467463200 SMD IC CS4334KS SO8 CRYST SMD IC LM833M NSC SMD IC 74VHCT541AMTC FAI SMD IC LM1117DT-1.8 SOT25 SMD IC M24C16CM1TR/-MN6T/ SMD IC PANTERA NDV8602VWA SMD IC 74ACT257MTC FAI SMD IC 74LCX573MTC FAI SMD IC 74LCX573MTC FAI FLASH LIVANCE 3xx SMD IC M29W800AT-90N1 ST SMD IC L7809CD2T STM SMD IC K4S643232-TC/L70 X1 838233627200 QUARZ #336-1 13C 27MHZ 30 Q1 Q2 Q4 Q5 Q6 Q7 Q8 Q9 Q13 Q20 830100785700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 SMD TRANS BC857 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 4-5 Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! ! (!) The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION POS. NR. ABB. POS. NO. FIG. MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG DESCRIPTION 267290860101 DIGITALPLATTE DIGITAL BOARD d © POS. NR. POS. NO. MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION POS. NR. POS. NO. MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION D1 D2 D3 D4 D5 D6 D7 D8 D9 D14 832521205300 832521205300 832521205300 830938404700 830938404700 830931309900 830931309900 830931309900 830931309900 830931309900 RP1 RP4 RP12 877003403700 877003403700 877003403700 SMD R-NETZ 1206 4X33 OHM SMD R-NETZ 1206 4X33 OHM SMD R-NETZ 1206 4X33 OHM U1 U3 U5 U6 U7 U8 U11 U12 U14 U15 830571543400 830575983400 830497454100 830576111700 830596001600 830477202300 830579125700 830470057300 830470057300 830470980100 U19 U22 830576470900 830467463200 SMD IC CS4334KS SO8 CRYST SMD IC LM833M NSC SMD IC 74VHCT541AMTC FAI SMD IC LM1117DT-1.8 SOT25 SMD IC M24C16CM1TR/-MN6T/ SMD IC PANTERA NDV8602VWA SMD IC 74ACT257MTC FAI SMD IC 74LCX573MTC FAI SMD IC 74LCX573MTC FAI FLASH LIVANCE 3xx SMD IC M29W800AT-90N1 ST SMD IC L7809CD2T STM SMD IC K4S643232-TC/L70 X1 838233627200 QUARZ #336-1 13C 27MHZ 30 SMD-DIODE BAT54A SMD-DIODE BAT54A SMD-DIODE BAT54A SMD-Z DIODE BZX 84 C4V7 SMD-Z DIODE BZX 84 C4V7 SMD DIODE BAV99 SMD DIODE BAV9 SMD DIODE BAV99 SMD DIODE BAV99 SMD DIODE BAV99 FB1 810498233000 SMD DAEMPF-PERLE 0805 BLM J3 J5 812612528900 829017504100 CINCH-BUCHSE 3-FACH LP HS EURO-AV BUCHSENL.21-POL J L3 L4 L5 L6 L7 L10 L11 L12 L13 L14 L15 L17 L21 814052980900 814052980600 814052980600 814052980600 814052980600 814052498400 814052498400 814052981200 814052980600 814052980600 814052980600 814052980600 814052981200 SMD DR 1210 400MA SBY3225 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SIEB-DR 39UH 10% LHL08 SIEB-DR 39UH 10% LHL08 T SMD DR 10UH 5% 1008NLV25T SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 2,2UH 5% 1008NLV25 SMD DR 10UH 5% 1008NLV25T Q1 Q2 Q4 Q5 Q6 Q7 Q8 Q9 Q13 Q20 Q24 Q25 830100785700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 830100784700 SMD TRANS BC857 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 SMD TRANS BC847 Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! ! (!) The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION Explosionszeichnungen und Ersatzteillisten / Exploded Views and Spare Parts Lists POS. NR. POS. NO. Livance – GDP 31… GRUNDIG Service ǵ ǵ 4-6 Ersatzteilliste Spare Parts List DVD 5 / 2001 NETZTEILPLATTE PSSH370603B POWER SUPPLY BOARD PSSH370603B Ersatzteilliste Spare Parts List DVD 9 / 2001 BEDIENPLATTE CONTROL BOARD MATERIAL-NR. / PART NO.: 267270150101 POS. NR. ABB. POS. NO. FIG. 0001.000 MATERIAL-NR. ANZ. PART NUMBER QTY. BEZEICHNUNG DESCRIPTION d © S 267270150101 NETZTEILPLATTE PSSH370603B POWER SUPPLY BOARD PSSH370603B S 759880802100 NETZBUCHSE 2P POWER JACK 2P MATERIAL-NR. / PART NO.: 267290810501 POS. NR. ABB. POS. NO. FIG. POS. NR. POS. NO. POS. NR. POS. NO. B 00001 CN 00002 MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION 759880801500 759880801600 CX 00101 S 759880802200 VERBINDER AUSGANG 18 POL. T 00101 KOND. 220NF 275V KOND. 1,5NF 400V D 00101 D 00102 D 00103 D 00104 D 00105 D 00106 D 00201 D 00202 D 00203 D 00204 D 00205 D 00206 D 00208 830921503300 830921503300 830921503300 830921503300 830951603800 830951703200 759880800100 759880800200 759880800300 759880402100 759880800400 759880800400 759880300600 DIODE 1N4007 ITT/SES/TFK DIODE 1N4007 ITT/SES/TFK DIODE 1N4007 ITT/SES/TFK DIODE 1N4007 ITT/SES/TFK DIODE BYV38 TFK AV619 -AM DIODE BYW32 TEMIC AV619DIODE SBL1040CT DIODE FES8BT DIODE UGF10GCT DIODE SBYV27-200 DIODE EGP20G DIODE EGP20G DIODE 1N 4148 F 00101 S 759813734800 759880800000 759880756300 IC 1M0365R IC KA431AZ/KIA431 L 00201 L 00202 L 00203 L 00204 L 00205 L 00206 759880801400 759880801300 759880801100 759880801200 759880801100 759880801200 SPULE 3.8 UH 5X20 SPULE 6.8UH SPULE 47 UH SPULE 300UH SPULE 47 UH SPULE 300UH TRAFO TSG-004 TH 00101 S 759880800800 VARISTOR 8 OHM ZD 00101 DIODE UZ-15BSC 759880800500 BEZEICHNUNG 267290810501 BEDIENPLATTE KEIN E-TEIL DESCRIPTION d © CONTROL BOARD NO SPARE PART MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION POS. NR. POS. NO. D1 830931307000 IR1 830546183500 IC TSOP1836SS3V IR RECEIV LED1 267300000301 LED-DISPLAY LTG-0136M Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 830100484700 SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SMD TRANS BC847B SW1 SW2 SW3 SW4 813402018600 813402018600 813402018600 813402018600 SCHALTER SKQNAC SCHALTER SKQNAC SCHALTER SKQNAC SCHALTER SKQNAC U1 830587131200 SMD IC UPD16312GB-3BS NE MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION SMD-DIODE BAV70 ALPS ALPS ALPS ALPS FILTER 15MH 1A OPTOKOPPLER H11A817A RV 00001 ESTR. EVN-1AC-A00-B13 GRUNDIG Service Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! ! (!) The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION Es gelten die Vorschriften und Sicherheitshinweise gemäß dem Service Manual "Sicherheit", Mat.-Nummer 720108000000, sowie zusätzlich die eventuell abweichenden, landesspezifischen Vorschriften! ! (!) The regulations and safety instructions shall be valid as provided by the "Safety" Service Manual, part number 720108000000, as well as the respective national deviations. ÄNDERUNGEN VORBEHALTEN / SUBJECT TO ALTERATION Livance – GDP 31… PC 00101 S 759880800600 759880800700 S 759880800900 WIDERST. SR37 0.5W WIDERST. SR37 0.5W SICHERUNG T2A H/250V IC 00101 IC 00201 S 759880801000 MATERIAL-NR. BEZEICHNUNG PART NUMBER DESCRIPTION RY 00101 S 759880802300 RY 00102 S 759880802300 FERRITPERLE BC3533 CY 00101 S 759880802400 LF00101 POS. NR. POS. NO. MATERIAL-NR. ANZ. PART NUMBER QTY. Explosionszeichnungen und Ersatzteillisten / Exploded Views and Spare Parts Lists ǵ ǵ