Download Samsung Reproductor Blu-ray H5900 Manual de Usuario
Transcript
BD-H5900 Blu-ray™ Disc Player user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register ENGLISH Safety Information CLASS 1 LASER product Warning TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lighting flash and Arrowhead within the triangle is a warning sign alerting you to dangerous voltage inside the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING • To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. FCC NOTE (for U.S.A) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: 2 The exclamation point within the triangle is a warning sign alerting you to important instructions accompanying the product. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect this equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This class B digital product meets all requirements of the Canadian Interference Causing Equipment Regulations. Note to CATV system installer This reminder is provided to call the CATV system installer's attention to Article 82040 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. This Compact Disc player is classified as a CLASS 1 LASER product. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. DANGER : • VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. (FDA 21 CFR) CAUTION : • CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO THE BEAM. (IEC 60825-1) • THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 PRODUCTO ✎✎ NOTES LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT LÁSER CLASE 1 `` If the Region number of a Blu-ray Disc/DVDs does not correspond to the Region number of this player, the player cannot play the disc. Precautions Important Safety Instructions Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including AV receivers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Disc Storage & Management • Holding Discs -- Fingerprints or scratches on a disc may reduce sound and picture quality or cause skipping -- Avoid touching the surface of a disc where data has been recorded. -- Hold the disc by the edges so that fingerprints will not get on the surface. -- Do not stick paper or tape on the disc. • Cleaning Discs -- If you get fingerprints or dirt on a disc, clean it with a mild detergent diluted in water and wipe with a soft cloth. -- When cleaning, wipe gently from the inside to the outside of the disc. • Disc Storage `` Do not keep in direct sunlight. `` Keep in a cool ventilated area. `` Keep in a clean protection jacket and store vertically. Handling Cautions • Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the apparatus. • To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times. • Do not plug multiple electric devices into the same wall socket. Overloading a socket can cause it to overheat, resulting in a fire. • Before connecting other components to this player, be sure to turn them off. • If you move your player suddenly from a cold place to a warm place, condensation may occur on the operating parts and lens and cause abnormal disc playback. If this occurs, unplug the player, wait for two hours, and then connect the plug to the power outlet. Then, insert the disc, and try to play back again. • If the product makes an abnormal noise or produces a burning smell or smoke, turn off the power switch immediately and disconnect the power plug from the wall outlet. Then, contact the nearest customer service center for technical assistance. Do not use the product. Using the product as it is may cause a fire or an electric shock. Using the 3D function IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and understand the following safety information before using the 3D function. • Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea, and headaches. If you experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest. • Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D TV, remove your 3D Active Glasses, and rest. • A responsible adult should frequently check on children who are using the 3D function. If there are any reports of tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest. • Do not use the 3D Active Glasses for other purposes (Such as general eyeglasses, sunglasses, protective goggles, etc.). • Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D Active Glasses while moving around may cause you to bump into objects, trip, and/or fall, and cause serious injury. • If you want to enjoy 3D content, connect a 3D device (3D compliant AV receiver or TV) to the player's HDMI OUT port using a high-speed HDMI cable. Put on 3D glasses before playing the 3D content. • The player outputs 3D signals only through HDMI cable connected to the HDMI OUT port. • As the video resolution in 3D play mode is fixed according to the resolution of the original 3D video, you can not change the resolution to your preference. • Some functions such as BD Wise, screen size adjustment, and resolution adjustment may not operate properly in 3D play mode. • You must use a high-speed HDMI cable for proper output of the 3D signal. • Stay at least three times the width of the screen from the TV when watching 3D images. For example, if you have a 46-inch screen, stay 138 inches (11.5 feet) from the screen. • Place the 3D video screen at eye level for the best 3D picture. • When the player is connected to some 3D devices, the 3D effect may not function properly. • This player does not convert 2D content into 3D. • "Blu-ray 3D" and "Blu-ray 3D" logo are trademarks of the Blu-ray Disc Association. Copyright © 2014 Samsung Electronics Co.,Ltd. All rights reserved; No part or whole of this user's manual may be reproduced or copied without the prior written permission of Samsung Electronics Co.,Ltd. 3 Contents Safety Information System Settings......................................... 16 Precautions.................................................. 2 Security Settings........................................ 16 Warning........................................................ 2 Disc Storage & Management........................ 3 Handling Cautions........................................ 3 Using the 3D functions................................. 3 Copyright..................................................... 3 Getting Started Before using the User Manual....................... 4 Logos of Discs the player can play............... 5 Accessories.................................................. 6 Front Panel................................................... 7 Rear Panel.................................................... 7 Remote Control............................................ 7 Connections Connecting to a TV....................................... 8 Connecting to an Audio System................... 8 Connecting to a Network Router.................. 9 Settings The Initial Settings Procedure..................... 10 Menu Navigation......................................... 10 Accessing the Settings Menu..................... 10 Display Settings.......................................... 10 Audio Settings............................................ 12 Network Settings........................................ 13 4 Language Settings...................................... 16 General Setting........................................... 17 Getting Started Before using the User Manual Disc Types and Contents your player can play Media Support Settings........................................ 17 Media Play Playing a Commercially Recorded Disc....... 18 VIDEO Playing Files on a USB Device.................... 18 Playing a Disc with User Recorded Content...................................................... 18 Playing Content Located on Your PC or AllShare Device through the Blu-ray Disc MUSIC Controlling Video Playback......................... 19 PHOTO Player......................................................... 19 Controlling Music Playback......................... 19 Playing Photo Contents.............................. 21 Appendix Troubleshooting.......................................... 21 Specifications............................................. 23 ✎✎ NOTES Disc Type Blu-ray Disc 3D Blu-ray Disc DVD-VIDEO DVD-RW DVD-R DVD+RW DVD+R CD-RW/-R, DVD-RW/-R, BD-RE/-R CD-RW/-R, DVD-RW/-R, BD-RE/-R Details BD-ROM or BD-RE/-R recorded in the BD-RE format. DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have been recorded and finalized, or a USB storage media containing MKV or MP4 contents. Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB storage media containing MP3 or WMA contents. Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB storage media containing JPEG contents. `` `` `` `` `` The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions. If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable. Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps. Your player will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds 25 Mbps. Playback may not work for some types of discs, or when you use specific functions, such as angle change and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary. `` When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly. Disc types your player cannot play • HD DVD • DVD-ROM/PD/ MV, etc • DVD-RAM • Super Audio CD (except CD layer) • DVD-RW (VR mode) • 3.9 GB DVD-R for Authoring. • CVD/CD-ROM/ CDV/CD-G/CD-I/LD (CD-Gs play audio only, not graphics.) Region Code Both players and discs are coded by region. These regional codes must match for a disc to play. If the codes do not match, the disc will not play. The Region Code for this player is displayed on the rear panel of the player. Disc Type Region Code Blu-ray Disc b a c DVDVIDEO Logos of Discs the player can play Blu-ray Disc BD-LIVE 3D Blu-ray Disc DivX Area North America, Central America, South America, Korea, Japan, Taiwan, Hong Kong and South East Asia. Europe, Greenland, French territories, Middle East, Africa, Australia and New Zealand. India, China, Russia, Central and South Asia. 1 The U.S., U.S. territories and Canada 2 Europe, Japan, the Middle East, Egypt, South Africa, Greenland 3 Taiwan, Korea, the Philippines, Indonesia, Hong Kong 4 Mexico, South America, Central America, Australia, New Zealand, Pacific Islands, Caribbean 5 Russia, Eastern Europe, India, most of Africa, North Korea, Mongolia 6 China NTSC broadcast system in U.S.A, Canada, Korea, Japan Supported File Formats Notes on the USB connection • Your player supports USB storage media, MP3 players, digital cameras, and USB card readers. • The player does not support folder or file names longer than 128 characters. • Some USB/External HDD/digital camera devices may not be compatible with the player. • Your player supports the FAT16, FAT32, and NTFS file systems. • Connect USB devices directly to the player’s USB port. Connecting through a USB cable may cause compatibility problems. • Inserting more than one memory device into a multi-card reader may cause the reader to operate improperly. • The player does not support the PTP protocol. • Do not disconnect a USB device during a "loading" process. • The bigger the image resolution, the longer the image takes to display. • This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from commercial sites. • Your player only supports video with a frame rate under 30fps (frames per second). • Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives and USB HDD. (HUB is not supported.) • Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this player. • If some USB devices require excessive power, they may be limited by the circuit safety device. • If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a wall socket. If the problem continues, contact the USB HDD manufacturer. • SAMSUNG is not responsible for any data file damage or data loss. • Your player does not support NTFS compressed files, sparse files, or encrypted files. • You can repair or format a USB device on your Desktop PC. (MS-Windows OS only). Video File Support File Extension Container *.avi AVI Video Codec DivX 3.11/4/5/6 MP4v3 H.264 BP/MP/HP *.mkv *.wmv MKV WMV (wmv9) *.mp4 MP4 *.mpg *.mpeg PS VC-1 AP H.264 BP/MP/HP VC-1 AP VC-1 SM MP4 (mp4v) H.264 BP/MP/HP MPEG1 MPEG2 H.264 BP/MP/HP Audio Codec MP3 Dolby Digital DTS WMA PCM MP3 Dolby Digital DTS WMA AAC MP1, 2 Dolby Digital DTS Resolution 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 5 •• Limitations -- Even when a file is encoded by a supported codec listed above, the file might not be played if its content has a problem. -- Normal playback is not guaranteed if the file’s container information is wrong or the file itself is corrupted. -- Files having a higher Bit rate/frame rate than standard may stutter during sound/video playback. -- The Seek (skip) function is not available if the file’s index table is damaged. •• Video decoder -- Supports up to H.264 Level 4.1 and AVCHD -- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4 -- MPEG4 SP, ASP : Below 1280 x 720 : 60 frames max Above 1280 x 720 : 30 frames max -- Does not support GMC 2 or higher ĞĞ Supported DivX subtitle file formats *.ttxt, *.smi, *.srt, *.sub, *.txt ✎✎ NOTES `` Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution and frame rate. Music File Support *.mp3 *.wma Container MP3 WMA Audio Codec Support Range WMA * Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48 * Bit rates - All bit-rates from 5kbps to 355kbps MP3 File Extension *.jpg *.jpeg *.jpe *.png Type Resolution JPEG 15360x8640 PNG 15360x8640 AVCHD (Advanced Video Codec High Definition) •• Audio decoder -- Supports WMA 7, 8, 9 and STD -- Does not support WMA sampling rate of 22050Hz mono. -- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96) Max bitrate: 320kbps. File Extension Picture File Support • This player can play back AVCHD format discs. These discs are normally recorded and used in camcorders. • The AVCHD format is a high definition digital video camera format. • The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the conventional image compressing format. • Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that use "x.v.Color" format. • "x.v.Color" is a trademark of Sony Corporation. • "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd. and Sony Corporation. ✎✎ NOTES `` Some AVCHD format discs may not play, depending on the recording condition. AVCHD format discs need to be finalized. `` "x.v.Color" offers a wider color range than normal DVD camcorder discs. Accessories Check for the supplied accessories shown below. - BONUS REPEAT REPEAT VIEW HDMI cable 6 Batteries for Remote Control (AAA Size) User Manual A-B FULL SCREEN Remote Control Front Panel PLAY/PAUSE BUTTON STOP BUTTON Remote Control Tour of the Remote Control Turn the player on and off. OPEN/CLOSE BUTTON Turn the TV on and off. After setup, allows you to set the input source on your TV. TV volume adjustment. Press to open and close the disc tray. POWER BUTTON Press the number buttons to operate options. Use to enter the popup menu/title menu. Use to enter the disc menu. Press to search a disc backwards or forwards. Press to pause a disc. Press to skip backwards or forwards. ✎✎ NOTES DISC TRAY REMOTE CONTROL SENSOR USB HOST `` When the player displays the Blu-ray Disc menu, you cannot start the movie by pressing the Play button on the player or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the v button. `` You can perform software upgrades using the USB Host jack with a USB flash memory stick only. Rear Panel Press to stop a disc. Press to move to the Home menu. Press to play a disc. Use to access various audio functions on a disc (Blu-ray Disc/DVD). Press to switch the Blu-ray Disc/DVD’s subtitle language. Press to use the Tools menu. Use to display the playback information when playing a Blu-ray Disc/DVDs. Use to select menu items and change menu values. Press to exit the menu. Return to the previous menu. These buttons are used both for menus on the player and also several Blu-ray Disc functions. Press to use bonusview function. BONUS REPEAT REPEAT VIEW A-B Installing batteries !! HDMI OUT LAN DIGITAL AUDIO OUT `` If the remote does not operate properly: • Check the polarity (+/–) of the batteries. Press to see the full screen on a TV. During the Blu-ray Disc/DVDs playback, Full Screen button does not operate. Allows you to repeat a title, chapter, track or disc. Allows you to repeat A-B disc. ✎✎ NOTES FULL SCREEN • Check if the batteries are drained. • Check if the remote sensor is blocked by obstacles. • Check if there is any fluorescent lighting nearby. CAUTION `` Dispose of batteries according to local environmental regulations. Do not put them in the household trash. `` Do not dispose of batteries in a fire. `` Do not short circuit, disassemble or overheat the batteries. `` Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 7 Connections Connecting to an Audio System Connecting to a TV Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. -- Do not connect the power cord to the wall outlet until you have made all the other connections. -- When you change the connections, turn off all devices before you start. You can connect the Blu-ray player to an audio system using one of the methods illustrated below. -- Do not connect the power cord to the wall outlet until you have made all the other connections. -- When you change the connections, turn off all devices before you start. Method 1 Connecting to an HDMI supported AV receiver • Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on your receiver. • Best quality (Recommended) Method 2 Connecting to an AV receiver with Dolby Digital or a DTS decoder Audio Video • Using a digital Coaxial cable (not supplied), connect the Coaxial Digital Audio Out jack on the product to the Digital Coaxial In jack of the receiver. • Good quality • You will hear sound only through the front two speakers with Digital Output set to PCM. ✎✎ NOTES `` If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio Out on the player to an audio system to hear audio. `` An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable. `` Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your TV. `` When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the first time, the player automatically sets the HDMI output resolution to the highest supported by the TV. `` A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Color to Off in the menu. `` To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable. `` HDMI outputs only a pure digital signal to the TV. If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the screen. 8 Method 1 Audio Method 2 Audio Connecting to a Network Router You can connect your player to your network router using one of the methods illustrated below. To use the AllShare network functionality, you must connect your PC to your network as shown in the illustrations. The connection can be wired or wireless. Wireless Network Wired Network Wireless Router Or Broadband modem (with integrated router) Broadband service ✎✎ NOTES `` If your wireless router supports DHCP, this player can use a DHCP or static IP address to connect to the wireless network. `` Set your wireless router to Infrastructure mode. Ad-hoc mode is not supported. Router Broadband modem ✎✎ NOTES Broadband service Broadband service `` Internet access to Samsung's software update server may not be allowed, depending on the router you use or your ISP's policy. For more information, contact your ISP (Internet Service Provider). `` DSL users, please use a router to make a network connection. `` The player supports only the following wireless security key protocols: - WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES) `` Select a channel on the wireless router that is not currently being used. If the channel set for the wireless router is currently being used by another device nearby, it will result in interference and communication failure. `` If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your router to WEP, TKIP or TKIP-AES (WPS2Mixed), the player will not support a connection in compliance with new Wi-Fi certification specifications. `` Wireless LAN, by its nature, may cause interference, depending on the operating conditions (router performance, distance, obstacles, interference by other radio devices, etc). 9 Settings The Initial Settings Procedure • The Home screen will not appear if you do not configure the initial settings. • The OSD (On Screen Display) may change in this player after you upgrade the software version. • The access steps may differ depending on the menu you selected. • After the loading process of this product is finished, the panel buttons and remote control can be operated. After you have connected the player to your TV, turn on the TV and player. When you turn on the player the first time, the player's Initial Settings screen appears on the TV. The Initial Setting procedure lets you set the On Screen Display (OSD) and menu languages, the aspect ratio (screen size), the network type, and connect the player to your network. 6 `` If you want to use the Anynet+(HDMI-CEC) function to aid in the initial set up process, please follow the instructions below. 1) Connect the player to an Anynet+(HDMICEC) compliant Samsung TV using HDMI Cable. 2) Set the Anynet+(HDMI-CEC) feature to On in both the TV and the player. 3) Set the TV to the Initial Settings Procedure. `` If you leave the player in the stop mode for more than 5 minutes without using it, a screen saver will appear on your TV. If the player is left in the screen saver mode for more than 25 minutes, the power will automatically turn off. Menu Navigation 10 1 Play Disc 8 App 1 1 2 3 8 HOME Button : Press to move to the Home VIEW A-B menu. BONUS REPEAT REPEAT 1 2 3 4 FULL SCREEN RETURN Button : Return to the previous menu. v (Enter) / DIRECTION Button : Move the cursor or select an item. Activate the currently selected item. Confirm a setting. EXIT Button : Press to exit the current menu. App 2 App 3 App 4 App 5 More Screen Mirroring Change Device 9 7 4 Music Empty disc tray 6 2 Videos 2 5 3 Photos 7 4 1 ✎✎ NOTES `` The Home menu will not appear if you do not configure the initial settings except as noted below. `` If you press the BLUE (D) button during network setup, you can access the Home menu even if the network setup is not completed yet. `` When you return to the Home menu, the full screen mode is cancelled automatically. `` If you want to display the Initial Setting screen again to make changes, press the @ button on the front panel of the player for more than 5 seconds with no disc inserted. This resets the player to its default settings. `` After the initial settings process is complete, you can operate the HDMI-CEC function. Accessing the Settings Menu • Home Menu 9 Settings 3 4 5 Selects Videos. Selects Music. Selects Settings. Selects Change Device. Selects Screen Mirroring. Selects Photos. To access the Settings menu and sub-menus, follow these steps: 1. Press the POWER button. The Home Menu appears. 2. Press the ▲▼◄► buttons to select Settings, and then press the v button. 3. Press the ▲▼ buttons to select the desired submenu, and then press the v button. 4. Press the ▲▼ buttons to select the desired item, and then press the v button. 5. Press the EXIT button to exit the menu. ✎✎ NOTES `` The access steps may differ depending on the menu you selected. The OSD (On Screen Display) may change in this player after you upgrade the software version. Display Settings Selects Play disc. Selects applications Selects More applications. ✎✎ NOTES `` The Videos, Photos, and Music options require that you have an appropriate disc inserted into the player or a USB flash device attached to the player. You can configure various display options such as the TV Aspect Ratio, Resolution, etc. 3D Settings Select whether to play a Blu-ray Disc with 3D contents in 3D Mode. ✎✎ NOTES `` For some 3D discs, to stop a movie during 3D playback, press the 5 button once. The movie stops and the 3D mode option is de-activated. To change a 3D option selection when you are playing a 3D movie, press the 5 button once. The Blu-ray menu appears. Press the 5 button again, then select 3D Settings in the Blu-ray menu. `` Depending on the content and the position of the picture on your TV screen, you may see vertical black bars on the left side, right side, or both sides. TV Aspect Ratio Depending on the type of television you have, you may want to adjust the screen size setting. ✎✎ NOTES `` Depending on the disc type, some aspect ratios may not be available. `` If you select an aspect ratio and option which is different than the aspect ratio of your TV screen, the picture might appear to be distorted. BD Wise (Samsung TVs only) BD Wise is Samsung’s latest inter-connectivity feature. When you connect a Samsung player and a Samsung TV with BD Wise to each other via HDMI, and BD Wise is on in both the player and TV, the player outputs video at the video resolution and frame rate of the Blu-ray Disc/ DVDs. ✎✎ NOTES `` When BD Wise is on, the Resolution setting automatically defaults to BD Wise and BD Wise appears in the Resolution menu. `` If the player is connected to a device that does not support BD Wise, you cannot use the BD Wise function. `` For proper operation of BD Wise, set the BD Wise menu of both the player and the TV to On. Resolution • DVD playback Lets you set the output resolution of the HDMI video signal to Auto, 1080p, 1080i, 720p or 480p. The number indicates the number of lines of video per frame. The i and p indicate interlaced and progressive scan, respectively. The more lines, the higher the quality. Resolution according to the output mode • Blu-ray Disc/E-contents/Digital Contents playback HDMI / connected Output Setup BD Wise Auto HDMI Mode Blu-ray Disc Resolution of Blu-ray Disc E-contents/ Digital contents 1080p Max. Resolution Max. Resolution of TV input of TV input 1080p@60F (Movie Frame : Off) 1080p@60F 1080p@60F Movie Frame : Auto (24Fs) 1080p@24F 1080p@24F 1080i 1080i 1080i 720p 720p 720p 480p 480p 480p Output Setup BD Wise HDMI / connected HDMI Mode 480i Auto Max. Resolution of TV input 1080p 1080p 1080i 1080i 720p 720p 480p 480p ✎✎ NOTES `` If the TV you connected to the player does not support Movie Frame or the resolution you selected, the message "If no pictures are shown after selecting ‘Yes’, please wait for 15 seconds to return to the previous resolution. Do you want to change the resolution?" appears. If you select Yes, the TV’s screen will go blank for 15 seconds, and then the resolution will revert to the previous resolution automatically. `` If the screen stays blank after you have changed the resolution, remove all discs, and then press and hold the @ button on the front of the player for more than 5 seconds. All settings are restored to the factory default. Follow the steps on the previous page to access each mode and select the Display Setup that your TV will support. `` When the factory default settings are restored, all stored user BD data is deleted. `` The Blu-ray Disc must have the 24 frame feature for the player to use the Movie Frame (24Fs) mode. Movie Frame (24Fs) Setting the Movie Frame (24Fs) feature to Auto allows you to adjust the player’s HDMI output to 24 frames per second for improved picture quality. You can enjoy the Movie Frame (24Fs) feature only on a TV supporting this frame rate. You can select Movie Frame only when the player is in the HDMI 1080p output resolution modes. HDMI Color Format Lets you set the color space format for HDMI output to match the capabilities of the connected device (TV, monitor, etc). HDMI Deep Color Lets you output video from the HDMI OUT jack with Deep Color. Deep Color provides more accurate color reproduction with greater color depth. Progressive Mode Lets you improve picture quality when viewing DVDs. 11 Audio Settings Digital Output Lets you select the digital audio output format that is suitable for your TV or AV Receiver. For more details, please refer to the Digital Output Selection table. Digital Output Selection Setup Connection PCM Audio Stream on Blu-ray Disc Audio Stream on DVD Definition for Blu-ray Disc 12 Bitstream (Unprocessed) PCM HDMI Receiver Coaxial Up to 7.1ch PCM 2ch Bitstream (Re-encoded DTS) HDMI Receiver Coaxial HDMI Receiver or Coaxial PCM PCM 2ch Re-encoded DTS Bitstream (Re-encoded Dolby D) HDMI supported AV receiver or Coaxial Re-encoded Dolby Digital * Re-encoded Dolby Digital * Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Re-encoded DTS Dolby Digital Plus PCM 2ch PCM 2ch Dolby Digital Plus Dolby Digital Re-encoded DTS Dolby TrueHD PCM 2ch PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS DTS-HD High Resolution Audio PCM 2ch PCM 2ch DTS Re-encoded DTS Re-encoded Dolby Digital * DTS-HD Master Audio DTS-HD High Resolution Audio Re-encoded Dolby Digital * PCM 2ch PCM 2ch DTS Re-encoded DTS Re-encoded Dolby Digital * PCM Dolby Digital DTS Any PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch DTS-HD Master Audio PCM 2ch Dolby Digital DTS PCM 2ch Dolby Digital DTS Outputs only main feature Decodes main feature audio stream so that your audio and BONUSVIEW AV receiver can decode the audio stream together audio bitstream. into PCM audio and add You will not hear BONUSVIEW Navigation Sound Effects. audio and Navigation Sound Effects. PCM 2ch Re-encoded Dolby Digital * Re-encoded Dolby Digital * PCM 2ch Dolby Digital Dolby Digital Decodes main feature audio and BONUSVIEW audio stream together into PCM audio and add Navigation Sound Effects, then re-encodes the PCM audio into DTS bitstream Decodes main feature audio and BONUSVIEW audio stream together into PCM audio and add Navigation Sound Effects, then reencodes the PCM audio into Dolby Digital bitstream DTS DTS ** If Source Stream is 2ch, "Re-encoded Dolby D" Settings are not applied. Blu-ray Discs may include three audio streams : -- Main Feature Audio : The audio soundtrack of the main feature. -- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary. -- Navigation Sound Effects : When you choose a menu navigation selection, a Navigation Sound Effect may sound. Navigation Sound Effects are different on each Blu-ray Disc. ✎✎ NOTES `` Be sure to select the correct Digital Output or you will hear no sound or just loud noise. `` If the HDMI device (AV receiver, TV) is not compatible with compressed formats (Dolby Digital, DTS), the audio signal outputs as PCM. `` Regular DVDs do not have BONUSVIEW audio and Navigation Sound Effects. `` Some Blu-ray Discs do not have BONUSVIEW audio and Navigation Sound Effects. `` If you play MPEG audio soundtracks, the audio signal outputs as PCM regardless of your Digital Output selections (PCM or Bitstream). `` If your TV is not compatible with compressed multi-channel formats (Dolby Digital, DTS), the player may output PCM 2ch downmixed audio even though you selected Bitstream (either Reencoded or Unprocessed) in the setup menu. `` If your TV is not compatible with PCM sampling rates over 48kHz, the player may output 48kHz downsampled PCM audio even though you set PCM Downsampling to Off. PCM Downsampling Lets you choose to have 96KHz PCM signals downsampled to 48KHz before they are outputted to an amplifier. Choose On if your amplifier or receiver is not compatible with a 96KHz signal. Dynamic Range Control Lets you apply dynamic range control to Dolby Digital, Dolby Digital Plus, and Dolby True HD audio. • Auto : Automatically controls the dynamic range of Dolby TrueHD audio, based on information in the Dolby TrueHD soundtrack. Also turns dynamic range control on for Dolby Digital and Dolby Digital Plus. • Off : Leaves the dynamic range uncompressed, letting you hear the original sound. • On : Turns dynamic range control on for all three Dolby formats. Quieter sounds are made louder and the volume of loud sounds is reduced. Downmixing Mode Lets you select the multi-channel downmix method that is compatible with your stereo system. You can choose to have the player downmix to normal stereo or to surround compatible stereo. Network Settings To begin setting up the network connection for your player, follow these steps: 1. In the Home menu, press the ▲▼ ◄► buttons to select Settings, and then press the v button. 2. Press the ▲▼ buttons to select Network, and then press the v button. 3. Press the ▲▼ buttons to select Network Settings, and then press the v button. 4. Press the ▲▼ buttons to select Network Type, and then press the v button. 5. Press the ▲▼ buttons to select Wired or Wireless, and then press the v button. 6. Go to the next section. Configuring Your Network Connection Before you begin, contact your ISP to find out if your IP address is static or dynamic. If it is dynamic, and you have a wired or wireless network, we recommend using the Automatic configuration procedures described below. If you are connecting to a wired network, connect the player to your router using a LAN cable before you start the configuration procedure. If you are connecting to a wireless network, disconnect any wired network connection before you begin. To begin configuring your network connection, follow these steps: Wired Network ĞĞ Wired - Automatic 1. In the Home screen, select Settings, and then press the v button. 2. Select Network, and then press the v button. 3. Select Network Settings, and then press the v button. 4. Select Wired in the Network Settings screen, and then press the v button. 5. Select Connect button, and then press the v button. The product detects the wired connection, verifies the network connection and then connects to the network. ĞĞ Wired - Manual If you have a static IP address or the Automatic procedure does not work, you'll need to set the Network Settings values manually. Follow Steps 1 and 2 in Wired - Automatic, and then follow these steps: 1. Select Network Status. The player searches for a network, and then displays the connection failed message. 2. On the bottom of the screen, select IP Settings, and then press the v button. The IP Settings screen appears. 3. Select the IP Setting field, and then press the v button. 4. Select Enter manually in the IP Setting field, and then press the v button. 5. Select a value to enter (IP Address, for example), and then press the v button. Use the number keypad on your remote control to enter the numbers for the value. Use the ◄► buttons on the remote control to move from entry field to entry field within a value. When done with one value, press the v button. 6. Press the ▲ or ▼ button to move to another value, and then enter the numbers for that value following the instructions in Step 5. 7. Repeat Steps 5 and 6 until you have filled in all values. ĞĞ Wireless - Automatic 1. In the Home screen, select Settings, and then press the v button. 2. Select Network, and then press the v button. 3. Select Network Settings, and then press the v button. 4. Select Wireless in the Network Settings screen, and then press the v button. The player searches for and then displays a list of the available networks. Network Settings ✎✎ NOTES Select your network type. Network type `` You can get the Network values from your Internet provider. 8. When finished entering all the values, and then press the RETURN or EXIT buttons. The player verifies the network connection and then connects to the network. Wireless Network You can setup a wireless network connection in four ways: -- Wireless Automatic -- Wireless Manual -- WPS(PBC) -- WPS(PIN) When you configure the wireless network connection, any wireless network devices currently connected through the player or, if applicable, the player's current wired connection, will be disconnected. Wireless Wireless network Add Network WPS(PBC) You can connect your Blu-ray player to the internet. Please select which wireless network to use. Search m Move " Select ' Return 5. Select the desired network, and then press the v button. 6. On the Security screen, enter your network's Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with an arrow button, and then pressing v button. 7. When done, select Done and then press the v button. The player verifies the network connection and then connects to the network. 8. When verification is complete, select OK, and then press the v button. ✎✎ NOTES `` You should be able to find the Security Code or Pass Phrase on one of the set up screens you used to set up your router or modem. 13 ĞĞ Wireless - Manual If you have a static IP address or the Automatic procedure does not work, you'll need to set the Network Settings values manually. 1. Follow the directions in Wireless Automatic through Step 5. 2. The player searches for a network, and then displays the connection failed message. 3. On the bottom of the screen, select IP Settings, and then press the v button. The IP Settings screen appears. 4. Select the IP Setting field, and then press the v button. 5. Select Enter manually in the IP Setting field, and then press the v button. 6. Select a value to enter (IP Address, for example), and then press v button. Use the number keypad on your remote control to enter the numbers for the value. Use the ◄► buttons on the remote control to move from entry field to entry field within a value. When done with one value, press the v button. 7. Press the ▲ or ▼ button to move to another value, and then enter the numbers for that value following the instructions in Step 6. 8. Repeat Steps 6 and 7 until you have filled in all values. ✎✎ NOTES `` You can get the Network values from your Internet provider. 9. When finished, and then press the RETURN or EXIT button. The Security Screen appears. 14 10.On the Security screen, enter your network's Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with the ▲▼◄► buttons, and then pressing the v button. 11.When finished, select Done at the right of the screen, and then press the v button. The player verifies the network connection and then connects to the network. 12.After the player verifies the network, select OK, and then press the v button. ĞĞ WPS(PBC) 1. In the Home screen, select Settings, and then press the v button. 2. Select Network, and then press the v button. 3. Select Network Settings, and then press the v button. 4. Select Wireless in the Network Settings screen, and then press the v button. 5. Press the ▲▼ button on your remote, and then press the ◄► button to select the WPS(PBC). 6. Press the v button on your remote. The "Press the PBC button" message appears. 7. Press the WPS(PBC) button on your router within two minutes. Your player automatically acquires all the network settings values it needs and connects to your network. The Network Status screen appears. The player connects to the network after the network connection is verified. ĞĞ WPS(PIN) Before you begin, open the router's setup menu on your PC and access the screen with the WPS PIN entry field. Network Test Use this menu item to check whether your network connection is working or not. 1. In the Home screen, select Settings, and then press the v button. Network Status 3. Select Network Settings, and then press the v button. Wi-Fi Direct 5. Select the desired network, and then press the ► button. ✎✎ NOTES 2. Select Network, and then press the v button. Use to check whether a connection to a network and the Internet has been established. 4. Select Wireless in the Network Settings screen, and then press the v button. The player searches for and then displays a list of the available networks. The Wi-Fi Direct function allows you to connect Wi-Fi Direct devices to the player and each other using a peer-to-peer network, without a wireless router. 6. Select the WPS(PIN), and then press the v button. The PIN pop-up appears. 7. Enter the PIN into the WPS PIN entry field in the router's Set Up screen and then save the the screen. ✎✎ NOTES `` Contact the manufacturer of the router for instructions explaining how to access the route's Set Up screens or refer to the router's user's manual. `` For WPS connection, set your wireless router’s security encryption to AES. Setting to WEP security encryption does not support WPS connection. `` Some Wi-Fi Direct devices may not support the AllShare function if connected via Wi-Fi Direct. If this is the case, it is advisable to change the network connection method between devices. `` Bluetooth transmissions can interfere with the Wi-Fi Direct signal. Before you use the Wi-Fi Direct function, we strongly recommend that you turn off the Bluetooth function of any active mobile device. 1. Turn on the Wi-Fi direct device and activate its Wi-Fi Direct function. 2. In the Home screen, select Settings, and then press the v button. 3. Select Network, and then press the v button. 4. Select Wi-Fi Direct, and then press the v button. The Wi-Fi Direct devices that you can connect appear. 5. You have three ways to complete the WiFi connection: • Through the Wi-Fi device. • Through the player using PBC. • Through the player using a PIN. Each is covered below. Through the Wi-Fi Device 1. On the Wi-Fi device, follow the procedure on the device for connecting to another Wi-Fi Direct device. See the device's user manual for instructions. 2. When you have completed the procedure, you should see a pop-up on your TV screen saying that a device that supports Wi-Fi Direct has requested to connect. Select OK, and then press the v button to accept. 3. The Connecting pop-up appears, followed by the Connected pop-up. When it closes, you should see the device listed on the Wi-Fi Direct screen as connected. Through the Player Using PBC 1. Select the Wi-Fi Direct device you want to connect to this player, and then press the v button. The PBC/PIN pop up appears. 2. Select PBC, and then press the v button. The PBC pop-up appears. 3. Press the PBC button on the Wi-Fi Direct device within 2 minutes. 4. The Connecting pop-up appears, followed by the Connected pop-up. When it closes, you should see the device listed on the Wi-Fi Direct screen as connected. Through the Player Using a PIN 1. Select the Wi-Fi Direct device you want to connect to this player, and then press the v button. The PBC/PIN pop up appears. 2. Select PIN, and then press the v button. The PIN pop-up appears. 3. Note the PIN code in the pop-up, and then enter it into the appropriate field in the Wi-Fi Direct device you want to connect. 4. The Connecting pop-up appears, followed by the Connected pop-up. When it closes, you should see the device listed on the Wi-Fi Direct screen as connected. ✎✎ NOTES `` The current wired or wireless network connection will be disconnected when you use the Wi-Fi Direct function. `` Text files, such as files with a .TXT or .DOC extension, will not display when you are using the Wi-Fi Direct function. Screen Mirroring The Screen Mirroring function lets you view the screen of your smart phone or android tablet on the TV you have connected to the Blu-ray player. 1. In the Home menu, press the ▲▼◄► buttons to select Screen Mirroring, and then press the v button. The Screen Mirroring pop-up appears. 2. Launch AllShare Cast on your device. 3. On your device, find the name of the Bluray player in the list of available devices and then select it. 4. The TV will display a PIN. Enter the PIN into your device. 5. The TV displays a connecting message (for example, Connecting to Android_92gb...) and then displays the connected message. 6. In a few moments, the screen of your device appears on the TV screen. 7. To stop Screen Mirroring, press the EXIT or RETURN button on the remote control, or disable Screen Mirroring function of your smart phone. ✎✎ NOTES `` You can connect to a device that supports AllShare Cast. Note that connecting to such a device may not be fully supported depending on the manufacturer. For further information on mobile connection support, refer to the manufacturer’s web site. `` When you are using the Screen Mirroring function, video stuttering or audio dropouts may occur, depending on your environment. `` Bluetooth transmissions can interfere with the Screen Mirroring signal. Before using the Screen Mirroring function, we strongly recommend that you turn off the Bluetooth function on your smart phone or smart device (tablet, etc.). Device Name Device Name function allows you to change player's name by selecting from device name list box. BD-Live Internet Connection Set to allow or prohibit an Internet connection when you use the BD-LIVE service. • Allow (All) : The Internet connection is allowed for all BD-LIVE contents. • Allow (Valid Only) : The Internet connection is allowed only for BD-LIVE contents containing a valid certificate. • Prohibit : No Internet connection is allowed for any BD-LIVE content. ✎✎ NOTES `` What is a valid certificate? When the player uses BD-LIVE to send the disc data and a request to the server to certify the disc, the server uses the transmitted data to check if the disc is valid and sends the certificate back to the player. `` The Internet connection may be restricted while you are using BD-LIVE contents. Using BD-LIVE™ Once the player is connected to the network, you can enjoy various movie-related service contents using a BD-LIVE compliant disc. 1. Attach a USB memory stick to the USB jack on the front of the player, and then check its remaining memory. The memory device must have at least 1GB of free space to accommodate the BD-LIVE services. 2. Insert a Blu-ray Disc that supports BDLIVE. 3. Select an item from various BD-LIVE service contents provided by the disc manufacturer. ✎✎ NOTES `` The way you use BD-LIVE and the provided contents may differ, depending on the disc manufacturer. 15 The AllShare Function AllShare lets you play music, video, and photo files located in your PC or NAS on the player. To use AllShare with your player, you must connect the player to your network. (See page 13-16). To use AllShare with your PC, you must install AllShare software on your PC. If you have NAS, you can use AllShare without any additional software. To download AllShare software 1. Go to Samsung.com 2. Click Support, enter your player’s product number in the field that appears, and then click Product. 3. On the next screen, click Get downloads under Downloads. 4. Click Software on the next page. 5. Click the icon in the AllShare line under File to start the download. System Settings Initial Settings By using the Initial Settings function, you can set the language, Network Settings, etc. For more information about the Initial Settings function, refer to the Initial Settings section of this user manual (See page 10). 16 Quick Start You can turn on the power quickly by decreasing the boot time. ✎✎ NOTES `` If this function is set to On, Standby power consumption will be increased. Anynet+ (HDMI-CEC) Anynet+ is a convenient function that offers linked operations with other Samsung players that have the Anynet+ feature. To operate this function, connect this player to an Anynet+ Samsung TV with an HDMI cable. With Anynet+ on, you can operate this player using a Samsung TV remote control and start disc playback simply by pressing the PLAY ( ) button on the TV’s remote control. For more information, please see the TV user manual. ✎✎ NOTES `` This function is not available if the HDMI cable does not support CEC. `` If your Samsung TV has an Anynet+ logo, then it supports the Anynet+ function. `` Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your TV. `` After the product was turned off, disconnecting and connecting the power cable turns it on automatically. At the moment, it automatically turns off in about 15 seconds for reestablishing Anynet+ connection. `` For some TV products, if connected to this product with Anynet+ function, turning the TV on may display a warning popup message saying no connection was found. Still, Anynet+ connection is properly established and available to use. BD Data Management Enables you to manage the downloaded contents you accessed through a Blu-ray disc that supports the BD-LIVE service and stored on a flash drive. You can check the device’s information including the storage size, delete the BD data, or change the Flash memory device. ✎✎ NOTES `` In the external memory mode, disc playback may be stopped if you disconnect the USB device in the middle of playback. `` Your player supports the FAT16, FAT32, and NTFS file systems. We recommend you use USB devices that support USB 2.0 protocol with 4 MB/sec or faster read/write speed. `` The Resume Play function may not work after you format the storage device. `` The total memory available to BD Data Management may differ, depending on the conditions. DivX® Video On Demand View DivX® VOD Registration Codes to purchase and play DivX® VOD contents. Language Settings You can select the language you prefer for the On-Screen menu, disc menu, audio, and subtitles. ✎✎ NOTES `` The selected language will only appear if it is supported on the disc. Security Settings The default security PIN is 0000. Enter the default PIN to access the security function if you haven't created your own PIN. After you have accessed the security function for the first time, change the PIN using the Change PIN function. BD Parental Rating Prevents playback of Blu-ray Discs with specific age ratings unless the 4 digit PIN is entered. DVD Parental Rating This function works in conjunction with DVDs that have been assigned an age rating or numeric rating that indicates the maturity level of the content. These numbers help you control the types of DVDs that your family can watch. Select the rating level you want to set. For example, if you select Level 6, discs rated above 6 - Level 7 and 8 - will not play. A larger number indicates more mature content. Change PIN Change the 4-digit password used to access security functions. If you forget your password 1. Remove any discs. 2. Press and hold the @ button on the front panel for 5 seconds or more. All settings will revert to the factory settings. ✎✎ NOTES `` When the factory default settings are restored, all the user stored BD data will be deleted. General Setting Time Zone Lets you specify the time zone that is applicable to your area. Support Settings Software Upgrade The Software Upgrade menu allows you to upgrade the player’s software for performance improvements or additional services. `` Samsung Electronics takes no legal responsibility for player malfunction caused by an unstable Internet connection or consumer negligence during a software upgrade. `` No disc should be in the product when you upgrade the software By Online. By USB To upgrade by USB, follow these steps: 1. Visit www.samsung.com/bluraysupport. 2. Download the latest USB software upgrade zip archive to your computer. By Online 3. Unzip the zip archive to your computer. You should have a single RUF file with the same name as the zip file. 1. In the player’s menu, go to Settings > Support > Software Upgrade. 5. Make sure there is no disc in the player, and then insert the USB flash drive into the USB port of the player. To upgrade By Online, follow these steps: 2. Select By Online, and then press the v button. The Connecting to Server message appears. 3. A popup message will appear if an update is available. 4. If you select Yes, download process started. (Never turn the player on during an upgrade.) 5. When the update is completed, the player will restart automatically. ✎✎ NOTES `` The upgrade is complete when the player turns off, and then turns on again by itself. `` Never turn the player off or back on manually during the update process. 4. Copy the RUF file to a USB flash drive. 6. In the player’s menu, go to Settings > Support > Software Upgrade. 7. Select By USB. ✎✎ NOTES `` No disc should be in the product when you upgrade the software using the USB Host jack. `` When the software upgrade is done, check the software details in the software Upgrade menu. `` Do not turn off the player during the software upgrade. It may cause the player to malfunction. `` Software upgrades using the USB Host jack must be performed with a USB flash memory stick only. Auto Upgrade Notification If you have connected the player to your network, and then set Auto Upgrade Notification on, the player automatically notifies you when a new software version is available for the player. To set Auto Upgrade Notification on, follow these steps: 1. Select Auto Upgrade Notification, and then press the v button. 2. Use the ▲▼ buttons to select On, and then press the v button. If there is a new software version available, the player notifies you with a popup message. Contact Samsung Provides contact information for assistance with your player. Terms of Service Agreement Lets you view the general disclaimer regarding third party contents and services. Reset Returns all settings to their factory defaults except for the network settings. 1. To upgrade the firmware, select Yes in the Pop-up. The player turns off automatically, then restarts, and begins the download. (Never turn the player on or off manually during an upgrade.) 2. The update progress popup appears. 3. When the update is completed, the player will restart automatically. ✎✎ NOTES `` The upgrade is complete when the player turns off, and then turns on again by itself. `` Never turn the player off or on manually during the update process. `` Samsung Electronics takes no legal responsibility for player malfunction caused by an unstable Internet connection or consumer negligence during software upgrade. 17 Media Play Play Disc Playing a Commercially Recorded Disc 1. Press the 8 button to open the disc tray. 2. Place a disc gently into the disc tray with the disc's label facing up. 3. Press the 8 button to close the disc tray. Playback starts automatically. Playing Files on a USB Device There are two methods you can use to play or view multimedia files located on a USB device through your player. Method 1 1. Turn the player on. 2. Connect the USB device to the USB port on the front panel of the player. The New Device Connected pop-up appears. Play Disc Photos Videos New device connected. Photos Empty disc tray Music 123 Videos Music > Move " Enter ' Return App 1 App 2 ✎✎ NOTES App 3 App 4 App 5 More Screen Mirroring Change Device Settings `` If the pop-up does not appear, go to Method 2. 18 3. Use the ▲▼ buttons to select Photos, Videos or Music, and then press the v button. The Photos, Videos & Music screen appears listing the content of the device. Depending on how the contents is arranged, you will see either folders, individual files, or both. ✎✎ NOTES `` Even though the player will display folders for all content types, it will only display files of the Content Type you selected in Step 3. For example, if you selected music, you will only be able to see music files. You can change this selection by returning to the Photos, Videos & Music screen and going to Step 3 in Method 2 below. 4. If necessary, use the ▲▼◄► buttons to select a folder, and then press the v button. 5. Select a file to view or play, and then press the v button. Photos Videos Music Change Device No Disc 123 a Empty disc tray App 1 App 2 App 3 App 4 App 5 More Close Screen Mirroring Change Device Settting 3. Use the ▲▼◄► buttons to select Photos, Videos or Music on the Home screen, and then press the v button. The Photos, Videos & Music screen appears listing the content of the device. Depending on how the contents is arranged, you will see either folders, individual files, or both. ✎✎ NOTES `` Even though the player will display folders for all content types, it will only display files of the Content Type you selected in Step 3. For example, if you selected music, you will only be able to see music files. You can change this selection by returning to the Photos, Videos & Music screen and repeating Step 3. 6. Press the RETURN button to exit a folder or the EXIT button to return to the Home screen. 4. If necessary, use the ▲▼◄► buttons to select a folder, and then press the v button. Method 2 6. Press the RETURN button to exit a folder or the EXIT button to return to Home screen. 7. Go to pages 19~21 for instructions that explain how to control playback of videos, music, and pictures on a USB device. 1. Turn the player on. 2. Connect the USB device to the USB port on the front panel of the player. Select Change Device and then press the ▲▼ to select USB. Press the v button. ✎✎ NOTES `` If you insert a disc when playing a USB device, the device mode changes to "Disc" automatically. Playing a Disc with User Recorded Content You can play multimedia files you have recorded on Blu-ray, DVD, or CD discs. 1. Place a user recorded disc into the disc tray with the disc’s label facing up, and then close the tray. 2. Use the ◄► buttons to select the type of content you want to view or play Videos, Photos, or Music - and then press the v button. ✎✎ NOTES `` Even though the player will display folders for all content types, it will only display files of the Content Type you selected in Step 2. For example, if you selected music, you will only be able to see music files. You can change this selection by returning to the Home screen and repeating Step 2. 5. Use the ▲▼◄► buttons to select a file to view or play, and then press the v button. 3. A screen appears listing the contents of the disc. Depending on how the contents are arranged, you will see either folders, individual files, or both. 7. Go to pages 19~21 for instructions that explain how to control playback of videos, music, and pictures on a USB device. 5. Use the ◄►▲▼ buttons to select a file to view or play, and then press the v button. 4. If necessary, use the ▲▼◄►buttons to select a folder, and then press the v button. 6. Press the RETURN button one or more times to exit a current screen, exit a folder, or to return to the Home screen. Press the EXIT button to return directly to the Home Screen. 7. Go to pages 19~21 for instructions that explain how to control playback of videos, music, and pictures on a disc. Playing Content Located on Your PC or AllShare Device through the Blu-ray Disc Player PC Blu-ray Disc Player Play back PC's files AllShare Connection 1. Connect the Blu-ray Disc Player, your PC, and/or your AllShare compatible device to the same wireless network. 2. Follow the directions in the AllShare software Installation/Instruction manual to set up devices and files for playing or viewing. 3. Select Change Device on the player's Home screen, and then press the v button. In the list of AllShare connected devices that appears, select your PC or other AllShare compatible device, and then press the v button. 4. Use the ◄► buttons to select the type of content you want to view or play Videos, Photos, or Music - and then press the v button. ✎✎ NOTES `` Even though the player will display folders for all content types, it will only display files of the Content Type you selected in Step 4. For example, if you selected music, you will only be able to see music files. You can change this selection by returning to the Home screen and repeating Step 4. 5. A screen appears listing the contents of the disc. Depending on how the contents are arranged, you will see either folders, individual files, or both. 6. If necessary, use the ▲▼◄►buttons to select a folder, and then press the v button. 7. Use the ◄►▲▼ buttons to select a file to view or play, and then press the v button. 8. Press the RETURN button one or more times to exit a current screen, exit a folder, or to return to the Home screen. Press the EXIT button to return directly to the Home Screen. 9. Go to pages 19~21 for instructions that explain how to control playback of videos, music, and pictures on a disc. Controlling Video Playback You can control the playback of video content located on a Blu-ray disc, DVD, CD, USB device, or you computer. Depending on the media, some of the functions described in this manual may not be available. During Blu-ray or DVD disc playback, the Full screen button does not operate. Buttons on the Remote Control used for Video Playback 2 Using the disc menu, title menu, popup menu, and title list DISC MENU button During playback, press this button to start the disc menu function. POPUP MENU button During playback, press this button to start the popup menu function. TITLE MENU button 1 Playback related buttons The player does not play sound in Search, Slow or Step mode. • To return to normal speed playback, press the 6 button. 6 button 5 button 7 button Fast Motion Play Slow Motion Play Step Motion Play Skip Motion Play BONUS REPEAT REPEAT VIEW A-B FULL SCREEN Starts playback. Stops playback. During playback, press this button to start the title menu function. Controlling Music Playback You can control the playback of music located on a Blu-ray disc, DVD, CD, USB device, or your computer. Buttons on the Remote Control used for Music Playback Pauses playback. During playback, press the 3 or 4 button. Each time you press the 3 or 4 button, the playback speed will change. In pause mode, press the 4 button. Each time you press the 4 button, the playback speed will change. In pause mode, press the 7 button. Each time you press the 7 button, a new frame appears. During playback, press the 1 or 2 button. Each time you press the 1 or 2 button, the disc moves to the previous or next chapter or file. 1 4 2 5 6 3 1 NUMBER buttons (Audio CD (CD-DA) only) : During Playlist playback, press the desired track number. The selected track is played. 2 Skip : During playback, press the 1 or 2 button to move to the previous or next file of VIEW A-B the playlist. 3 5 button : Stops a track. BONUS REPEAT REPEAT FULL SCREEN 19 4 5 6 Fast Play (Audio CD (CD-DA) only) During playback, press the 3 or 4 button. Each time you press the 3 or 4 button, the playback speed will change. Pause : Pauses a track. Playlist Tools TRACK 001 Repeat Mode ? Off Rip TRACK 002 TRACK 001 1/6 \05:57 04:27 > Move < Adjust ' Return TRACK 003 + 00:08 / 05:57 TRACK 004 TRACK 005 TRACK 006 CD " Pause c Select 04:07 03:41 03:17 03:35 Tools ' Return 2. Press the ◄► buttons to select Track, All, Shuffle, or Off. 3. Press the v button. Songs are played in the order in which they were recorded. Off ( ) Track The current song is repeated. )Shuffle Shuffle plays songs in random order. ( 20 ) All All songs are repeated. 1/2 Page TRACK 001 TRACK 001 6 button : Plays the currently selected track. 1. During Playlist playback, press the TOOLS button. ( 1. To move to the Music List, press the 5 or RETURN button. The Music List screen appears. Music Repeat an Audio CD (CD-DA)/ MP3 Playlist TRACK 002 02:38 02:38 TRACK 003 TRACK 004 02:38 02:38 TRACK 006 TRACK 005 02:38 02:38 02:38 02:38 TRACK 008 TRACK 007 TRACK 010 TRACK 009 02:38 02:38 CD aChange Device c Select Tools ( ) Jump Page ' Return 2. Press the ▲▼◄► buttons to move to a desired track, and then press the YELLOW (C) button. A check appears on the track. Repeat this procedure to select additional tracks. 3. To remove a track from the list, move to the track, and then press the YELLOW (C) button again. The check on the track is cancelled. 4. When done, press the v button. The tracks you selected are displayed on the right side of the screen. The player plays the first track. 5. To change the play list, press the @ button or RETURN button to return to the Music List. Repeat Steps 2, 3, and 4. 6. To cancel the play list and return to the Home screen, press the RETURN or EXIT button. ✎✎ NOTES `` You can create a playlist with up to 99 tracks on Audio CDs (CD-DA). `` If you remove all the tracks from a play list and then press the v button, the player lists and plays all the tracks on the disc. Ripping Lets you copy audio files contents from data Disc to USB/HDD device. 1. Open the disc tray. Place the audio (CDDA) disc on the tray, and close the tray. Insert a USB device into the USB jack on the front of the product. 2. Press the ▲▼◄► buttons to move to a desired track, and then press the YELLOW (C) button. A check appears on the track. Repeat this procedure to select additional tracks. 3. To remove a track from the list, move to the track, and then press the YELLOW (C) button again. The check on the track is cancelled 4. When done, press the TOOLS button and then select the Rip using the ▲▼ buttons, and then press the v button. The Rip pop-up appears. 5. Use the ▲▼ buttons to select the device to store the ripped files to, and then press the v button. ✎✎ NOTES `` Do not disconnect the device while ripping is in progress. 6. If you want to cancel ripping, press the v button and then select Yes. Select No to continue ripping. 7. When ripping is complete, the "Ripping is completed." message appears. Press the v button to go back to the Playback screen. ✎✎ NOTES `` This function may not be supported by some discs. `` On the Ripping screen, you can also choose Select All and Deselect All. -- Use Select All to select all tracks. This cancels your individual track selections. -- Use Deselect All to deselect all selected tracks at once. Disc Copy to USB Lets you copy video/photo/music contents from data Disc to USB/HDD device. 1. Open the disc tray. Place the data disc on the tray, and close the tray. Insert a USB device into the USB jack on the front of the product. 2. Press the ▲ button, and then press the ◄► to select Blu-ray, DVD or CD. 3. Use the ▲▼ buttons to select Photos, Videos or Music, and then press the v button. The Photos, Videos & Music screen appears listing the content of the device. Depending on how the contents is arranged, you will see either folders, individual files, or both. ✎✎ NOTES `` Even though the player will display folders for all content types, it will only display files of the Content Type you selected in Step 3. For example, if you selected music, you will only be able to see music files. You can change this selection by returning to the Photos, Videos & Music screen and repeating Step 3. 4. With the Playback screen displayed, Use the ▲▼◄► buttons to select the Videos, Photos, or Music, and then press the YELLOW (C) button. A check appears to the left of the desired item. 5. Repeat Step 4 to select and check additional desired item. 6. To remove the desired item from the list, press the YELLOW (C) button again. The check on the desired item is removed. 7. When done, press the TOOLS button and then select the Copy to USB using the ▲▼ buttons, and then press the v button. The Copy to USB pop-up appears. 8. Use the ▲▼ buttons to select the device to store the copied files, and then press the v button. ✎✎ NOTES `` Do not disconnect the device while copying is in progress. 9. If you want to cancel copying, press the v button and then select Yes. Select No to continue copying. 10.When copying is complete, the "Copying is completed." message appears. Press the v button to go back to the Playback screen. ✎✎ NOTES `` This function may not be supported by some discs. `` On the Copying screen, you can also choose Select All and Deselect All. -- Use Select All to select all item. This cancels your individual item selections. -- Use Deselect All to deselect all selected item at once. Playing Photo Contents You can control the playback of photo content located on a Blu-ray disc, DVD, CD, USB device, or your computer. Using the Tools Menu During playback, press the TOOLS button. Start Slide Show/ Select to start or stop the slide Stop Slide Show show. Slide Show Speed Select to set a slide show's speed. Background Music Appendix Troubleshooting Before requesting service, please try the following solutions. PROBLEM SOLUTION No operation can be performed with the remote control. • Check the batteries in the remote control. They may need replacing. • Operate the remote control at a distance of no more than 6.1m from the player. • Remove batteries and hold down one or more buttons for several minutes to drain the microprocessor inside the remote control to reset it. Reinstall batteries and try to operate the remote control again. Select to listen to music while viewing a slide show. Zoom Select to enlarge the current picture. (Enlarge up to 4 times) Disc does not play. Rotate Select to rotate the picture. (This will rotate the picture either clockwise or counter clockwise.) • Ensure that the disc is installed with the label side facing up. • Check the region number of the Blu-ray Disc/DVD. Disc Menu does not appear. • Ensure that the disc has disc menus. The prohibition message appears on the screen. • This message appears when an invalid button is pressed. • The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles). • You’ve requested a title or chapter number or search time that is out of range. Play mode differs from the Setup Menu selection. • Some of the functions selected in the Setup Menu may not work properly if the disc is not encoded with the corresponding function. The screen ratio cannot be changed. • The Screen Ratio is fixed on your Blu-ray Disc/DVD. • This is not a problem with the player. No audio. • Make sure you have selected the correct Digital Output in the Audio Options Menu. The screen is blank. • If the HDMI output is set to a resolution your TV cannot support (for example, 1080p), you may not see a picture on your TV. • Press the @ button (on front panel) for more than 5 seconds with no disc inside. All settings will revert to the factory settings. • When the factory default settings are restored, all stored user BD data is deleted. Information ✎✎ NOTES Shows the picture information. `` Depending on the disc or storage device, the Tools menu may differ. `` To enable the background music function, the photo file must be in the same storage media as the music file. However, the sound quality can be affected by the bit rate of the MP3 file, the size of the photo, and the encoding method. `` You can't enlarge the subtitle and PG graphic in the full screen mode. 21 PROBLEM SOLUTION PROBLEM SOLUTION Forgot password • Press the @ button (on front panel) for more than 5 seconds with no disc inside. All settings including the password will revert to the factory settings. Don’t use this unless absolutely necessary. • When the factory default settings are restored, all stored user BD data is deleted. I cannot connect to the BDLIVE server. The picture is noisy or distorted • Make sure that the disc is not dirty or scratched. • Clean the disc. No HDMI output. • Check the connection between the TV and the HDMI jack of the player. • Check if your TV supports 480p, 720p, 1080i, or 1080p HDMI input resolutions. • Check whether the network connection is working or not by using the Network Status menu. • Check whether the USB memory device is connected to the player. • The memory device must have at least 1GB of free space to accommodate the BD-LIVE service. You can check the available size in BD Data Management. • Check whether the BD-LIVE Internet Connection menu is set to Allow(All). • If all above fails, contact the contents provider or update the player to the latest firmware. Abnormal HDMI output screen. • If random noise appears on the screen, it means that TV does not support HDCP (High-bandwidth Digital Content Protection). When using the BD-LIVE service, an error occurs. • The memory device must have at least 1GB of free space to accommodate the BD-LIVE service. You can check the available size in BD Data Management. If you experience other problems. • Go to the contents and find the section of the user manual that contains the explanations regarding the current problem, and follow the procedure once again. • If the problem still cannot be solved, please contact your nearest Samsung authorized service center. AllShare function ✎✎ NOTES `` When the factory default settings are restored, all stored user BD data is deleted. Repairs If you contact us to repair your player, an administration fee may be charged if either: I can see folders shared through AllShare, but I cannot see the files. • AllShares shows only files corresponding to the Image, Music, and Movie categories. Files that do not correspond to these categories are not displayed. Video is played intermittently. • Check if the network is stable. • Check if the network cable is properly connected and if the network is overloaded. • The wireless connection between the AllShare compatible device and the player is unstable. Check the connection. AllShare connection between Player and PC is unstable. • The IP address under the same subnetwork should be unique. If they are not, IP interference can cause this phenomenon. • Check if you have a firewall enabled. If so, disable the firewall function. 22 BD-LIVE 1. An engineer is called out to your home at your request and there is no defect in the product. 2. You bring the unit to a repair center and there is no defect in the product. We will provide you with the amount of the administration fee before we make a home visit or begin any work on your player. We recommend you read this manually thoroughly, search for a solution on line at www. samsung.com, or contact Samsung Customer Care before seeking to repair your player. Specifications General USB HDMI Audio Output Network Power Requirements AC110-127V 50/60Hz (Mexico only) (Other Country : AC100-240V) Power Consumption 9.8W Weight 1.2 Kg Dimensions 360 (W) X 196 (D) X 39 (H) mm Operating Temperature Range +5°C to +35°C Operating Humidity Range 10 % to 75 % Type A USB 2.0 DC output 5V 0.5A Max. Video 2D : 1080p, 1080i, 720p, 480p 3D : 1080p, 720p Audio PCM, Bitstream Digital Audio Output Coaxial Ethernet 100BASE - TX Terminal Wireless LAN Built-In Security WEP (OPEN/SHARED) WPA-PSK (TKIP/AES) WPA2-PSK (TKIP/AES) WPS(PBC) Supported -- Network speeds equal to or below 10Mbps are not supported. -- Design and specifications are subject to change without prior notice. -- Weight and dimensions are approximate. 23 Compliance and Compatibility Notice NOT ALL discs are compatible • Subject to the restrictions described below and those noted throughout this Manual, including the Disc Type and Characteristics section of this user manual, disc types that can be played are: pre-recorded commercial BD-ROM, DVD-VIDEO, and Audio CD (CD-DA) discs; BD-RE/-R, DVD-RW/-R discs; and CD-RW/-R discs. • Discs other than those listed above cannot be and are not intended to be played by this player. Some of the discs listed above may not play due to one or more reasons provided below. • Samsung cannot assure that this player will play every disc bearing the BD-ROM, BD-RE/-R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R and CD-RW/-R logos, and this player may not respond to all operating commands or operate all features of every disc. These and other disc compatibility and player operation issues with new and existing format discs are possible because: -- Blu-ray is a new and evolving format and this player may not operate all features of Bluray Discs because some features may be optional, additional features may have been added to the Blu-ray Disc format after the production of this player, and certain available features may be subject to delayed availability; -- not all new and existing disc format versions are supported by this player; -- new and existing disc formats may be revised, changed, updated, improved and/or supplemented; -- some discs are produced in a manner that allows specific or limited operation or restricts features during playback; -- some discs bearing the BD-ROM, BD-RE/-R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R and CD-RW/-R logos may still be non-standardized discs; -- some discs may not be played depending on their physical state or recording conditions; -- problems and errors can occur during the creation of Blu-ray Disc or DVD software and/or the manufacture of discs; -- this player operates differently than a standard DVD player or other AV equipment; and/or -- for reasons noted throughout this user manual and for other reason(s) discovered and posted by SAMSUNG customer care center. • If you encounter disc compatibility or player operation problems, please contact SAMSUNG customer care center. You may also contact SAMSUNG customer care center for possible updates on this player. • For additional information on playback restrictions and disc compatibility, refer to the Precautions, Before Reading the user manual, Disc Types and Characteristics, and Before Playing sections of this user manual. 24 • For Blu-ray Disc Player progressive scan output : CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS product AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS product, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. Copy Protection • Because AACS (Advanced Access Content System) is approved as the content protection system for the Blu-ray Disc format, similar to use of CSS (Content Scramble System) for the DVD format, certain restrictions are imposed on playback, analog signal output, etc., of AACS protected contents. The operation of this product and restrictions on this product may vary depending on your time of purchase as those restrictions may be adopted and/or changed by AACS after the production of this product. Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for the Blu-ray Disc format, which imposes certain restrictions including playback restrictions for BD-ROM Mark and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+, or this product, please contact SAMSUNG customer care center. • Many Blu-ray Disc/DVDs are encoded with copy protection. Because of this, you should only connect your Player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected Blu-ray Disc/DVDs. • Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use, display, distribution, or revision of television programs, videotapes, Blu-ray Discs, DVDs, and other materials may subject you to civil and/or criminal liability. • Cinavia Notice : This product uses Cinavia technology to limit the use of unauthorized copies of some commercially-produced film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted. More information about Cinavia technology is provided at the Cinavia Online Consumer Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego CA, 92138, USA. This product incorporates proprietary technology under licence from Verance Corporation and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2013 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited Network Service Disclaimer All content and services accessible through this device belong to third parties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal noncommercial use. You may not use any content or services in a manner that has not been authorized by the content owner or service provider. Without limiting the foregoing, unless expressly authorized by the applicable content owner or service provider, you may not modify, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or distribute in any manner or medium any content or services displayed through this device. THIRD PARTY CONTENT AND SERVICES ARE PROVIDED "AS IS." SAMSUNG DOES NOT WARRANT CONTENT OR SERVICES SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE. SAMSUNG EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SAMSUNG DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS, LEGALITY, OR COMPLETENESS OF ANY CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE AND UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL SAMSUNG BE LIABLE, WHETHER IN CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN CONNECTION WITH, ANY INFORMATION CONTAINED IN, OR AS A RESULT OF THE USE OF ANY CONTENT OR SERVICE BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Third party services may be terminated or interrupted at any time, and Samsung makes no representation or warranty that any content or service will remain available for any period of time. Content and services are transmitted by third parties by means of networks and transmission facilities over which Samsung has no control. Without limiting the generality of this disclaimer, Samsung expressly disclaims any responsibility or liability for any interruption or suspension of any content or service made available through this device. Samsung is neither responsible nor liable for customer service related to the content and services. Any question or request for service relating to the content or services should be made directly to the respective content and service providers. License • Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. • For DTS patents, see http://patents.dts.com. Manufactured under licence from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS 2.0+Digital Out is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved. 2.0+Digital Out • DivX -- ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that has passed rigorous testing to verify that is plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos. -- ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration. -- DivX Certified® to play DivX® video up to HD 1080p, including premium content. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under licence. Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274. • The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. • Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners • Open Source License Notice -- In the case of using open source software, Open Source Licenses are available on the product menu. • Blu-ray Disc™, Blu-ray™ and the logos are trademarks of the Blu-ray Disc Association. 25 Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country ` North America CANADA Contact Center 1-800-SAMSUNG (726-7864) U.S.A MEXICO 1-800-SAMSUNG (726-7864) 01-800-SAMSUNG (726-7864) ARGENTINE URUGUAY PARAGUAY 0800-333-3733 000 405 437 33 009 800 542 0001 0800-124-421 (Demais cidades e regiões) 4004-0000 (Capitais e grandes centros) 800-SAMSUNG(726-7864) 800-10-7260 01 8000 112 112 Bogotá 600 12 72 ` Latin America BRAZIL CHILE BOLIVIA COLOMBIA COSTA RICA DOMINICA 0-800-507-7267 1-800-751-2676 Web Site www.samsung.com/ca (English) www.samsung.com/ca_fr (French) www.samsung.com/us www.samsung.com Country Contact Center ECUADOR 1-800-10-7267 EL SALVADOR 800-6225 GUATEMALA 1-800-299-0013 www.samsung.com.ar www.samsung.com www.samsung.com.py HONDURAS 800-27919267 NICARAGUA 001-800-5077267 www.samsung.com/cl www.samsung.com PANAMA www.samsung.com.br www.samsung.com/co www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) JAMAICA PERU PUERTO RICO TRINIDAD & TOBAGO VENEZUELA 1-800-234-7267 800-7267 0-800-777-08 1-800-682-3180 1-800-SAMSUNG(726-7864) 0-800-100-5303 Web Site www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/pe www.samsung.com www.samsung.com www.samsung.com/ve BD-H5900 Reproductor de discos Blu-ray™ manual del usuario Para prevenir cualquier mal funcionamiento y evitar daños, lea detalladamente este manual de instrucciones antes de conectar y operar el aparato. Conserve el manual para futuras referencias Gracias. imagine las posibilidades Gracias por adquirir este producto Samsung. Para recibir un servicio más completo, registre su producto en www.samsung.com/register Español Información de seguridad Producto LÁSER DE LA CLASE 1 Advertencia PARA REDUCIR EL PELIGRO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA. NO HAY PIEZAS EN EL INTERIOR QUE PUEDA REPARAR EL USUARIO. CONSULTE AL PERSONAL CUALIFICADO DE SERVICIO TÉCNICO. PRECAUCIÓN Riesgo de descarga eléctrica No abrir Un triángulo con un rayo y una punta de flecha es un símbolo de advertencia que alerta de "voltaje peligroso" dentro del producto. PRECAUCIÓN: PARA REDUCIR EL PELIGRO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA. NO HAY PIEZAS EN EL INTERIOR QUE PUEDA REPARAR EL USUARIO. CONSULTE AL PERSONAL CUALIFICADO DE SERVICIO TÉCNICO. ADVERTENCIA Para reducir el riesgo de incendio o descarga eléctrica, no exponga este aparato a la lluvia ni a la humedad. NOTA DE FCC (para EE.UU.) Este equipo ha sido probado y cumple con los límites para un dispositivo digital de la Clase B, de acuerdo con la Parte 15 de las Normas de FCC. Estos límites se han diseñado para proporcionar una protección razonable frente a interferencias peligrosas en un entorno residencial. Este equipo genera, utiliza y puede radiar energía de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencias peligrosas en la recepción de radio y televisión, lo cual puede determinarse apagando y encendiendo el equipo. El usuario debe intentar corregir las interferencias mediante una de las siguientes medidas. 2 Un triángulo con un signo de exclamación es un símbolo de advertencia que le alerta de que hay instrucciones importantes relacionadas con el producto. • Reoriente o reubique la antena de recepción. • Aumente la separación entre el equipo y el receptor. • Conecte el equipo en una toma de un circuito diferente al que esté conectado el receptor. • Consulte al distribuidor o a un técnico experimentado de radio / TV para obtener ayuda. Este Aparato digital de la Clase B cumple todos los requisitos de la Normativa de equipos que causan interferencias de Canadá. Nota para el instalador del sistema CATV Este recordatorio se facilita para llamar la atención del instalador del sistema CATV sobre el Artículo 820-40 del Código Eléctrico Nacional (Sección 54 de Código Eléctrico Canadiense, Parte I), que proporciona directrices para una conexión a tierra apropiada y, en concreto, especifica que la conexión a tierra del cable se conectará al sistema de conexión a tierra del edificio, lo más cerca posible del punto de entrada del cable. Este reproductor de CD está clasificado como un productor LÁSER de CLASE 1. El uso de controles, ajustes o la ejecución de procedimientos distintos a los especificados en este documento pueden dar como resultado la exposición peligrosa a radiaciones. PELIGRO : • RADIACIÓN DE LÁSER VISIBLE E INVISIBLE AL ABRIR. EVITE LA EXPOSICIÓN DIRECTA AL HAZ DE LUZ. (FDA 21 CFR) • ESTE PRODUCTO UTILIZA UN LÁSER. EL USO DE CONTROLES, AJUSTES O PROCEDIMIENTOS NO ESPECIFICADOS EN ESTE DOCUMENTO PUEDEN TENER COMO RESULTADO LA EXPOSICIÓN A RADIACIONES PELIGROSAS. NO ABRA LAS CUBIERTAS NI REALICE REPARACIONES POR SU CUENTA. CONSULTE AL PERSONAL CUALIFICADO DE SERVICIO TÉCNICO. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 PRODUCTO ✎ NOTA LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT LÁSER CLASE 1 `` Si el número de región de un disco Blu-ray/ DVD no corresponde con el número de región de este reproductor, éste no podrá reproducir el disco. Precauciones Instrucciones importantes de seguridad Lea estas instrucciones de funcionamiento detenidamente antes de utilizar la unidad. Siga las instrucciones de seguridad que se incluyen a continuación. Tenga estas instrucciones de funcionamiento a mano para referencia futura. 1. 2. 3. 4. 5. 6. 7. Lea estas instrucciones. Conserve estas instrucciones. Preste atención a todas las advertencias. Siga todas las instrucciones. No utilice este aparato cerca del agua. Límpielo sólo con un paño seco. No bloquee ningún orificio de ventilación. Instálelo de acuerdo a las instrucciones del fabricante. 8. No lo instale cerca de ninguna fuente de calor como radiadores, registradores de calor, hornos u otros aparatos que generen calor (incluidos receptores de AV). 9. No ignore el fin de seguridad de los enchufes polarizados o con toma de tierra. Un enchufe polarizado tiene dos puntas, una más ancha que la otra. Un enchufe con toma de tierra tiene dos puntas y una tercera hoja de toma de tierra. La punta ancha o la tercera hoja existen por motivos de seguridad. Si no cabe en la toma, consulte a un electricista para sustituir la toma obsoleta. 10. Proteja el cable de alimentación para que no se pise ni se produzcan pinzamientos, especialmente en los enchufes, en sus respectivos receptáculos y en los puntos de salida del aparato. 11. Utilice sólo accesorios especificados por el fabricante. 12. Utilice sólo las mesitas con ruedas, soportes, trípodes o mesas recomendadas por el fabricante o que se vendan con el aparato. Cuando se utilice una mesita con ruedas, tenga cuidado al moverla junto con el aparato para evitar daños por vuelco. 13. Desenchufe este aparato durante tormentas eléctricas o cuando no se utilice por largos períodos de tiempo. 14.Confíe las reparaciones a personal técnico cualificado. El servicio técnico es necesario cuando el aparato se haya dañado de alguna forma, cuando el cable o el enchufe de suministro eléctrico se haya dañado, cuando se haya derramado líquido sobre el aparato o hayan caído objetos en su interior, el aparato se haya expuesto a la lluvia o humedad, no funcione normalmente o se haya caído. Almacenamiento y manejo de discos • Sujeción de discos -- Fingerprints or scratches on a disc may reduce sound and picture quality or cause skipping -- Huellas o arañazos en el disco pueden reducir la calidad del sonido y de la imagen o provocar saltos. -- Sujete el disco por sus bordes de forma que no deje huellas en su superficie. -- No adhiera papel ni cinta en el disco. • Limpieza de discos -- Si deja huellas en el disco, límpielas con un detergente suave diluido en agua y límpielo con un paño suave. -- Al limpiar, pase el paño suavemente de dentro a fuera del disco. • Almacenamiento de discos `` No los exponga a la luz directa del sol. `` Guárdelos en un área ventilada fresca. `` Guárdelos en una funda de protección limpia y en posición vertical. Precauciones de manejo • No debe exponer este aparato a gotas ni salpicaduras de agua. No coloque en el aparato objetos con líquido, como jarrones. • Para apagar completamente este aparato, debe desconectar su enchufe de la toma de corriente. Por tanto, el enchufe debe estar accesible en todo momento. • No enchufe varios dispositivos electrónicos en la misma toma de corriente. Si se sobrecarga una toma puede provocar sobrecalentamiento y causar un incendio. • Antes de conectar otros componentes a este reproductor, asegúrese de que estén apagados. • Si traslada de forma repentina el reproductor de un lugar frío a un lugar cálido, es posible que se produzca condensación en sus componentes y en la óptica, y provoque una reproducción anormal del disco. Si sucede, desenchufe el reproductor, espere dos horas y vuelva a conectar el enchufe a la toma de corriente eléctrica. A continuación, inserte el disco e intente reproducirlo de nuevo. • Si detecta ruidos anormales, olor a quemado o humo en el producto, apague el interruptor de alimentación inmediatamente y desconecte el enchufe de la toma de corriente. A continuación, póngase en contacto con el centro de servicio técnico más cercano para obtener asistencia técnica. No utilice el producto. Utilizar el producto en este estado podría provocar un incendio o una descarga eléctrica. Utilización de la función 3D INFORMACIÓN IMPORTANTE SOBRE SALUD Y SEGURIDAD CON RESPECTO A IMÁGENES EN 3D. Antes de utilizar la función 3D, lea y recuerde la información de seguridad que se incluye a continuación. • Es posible que al ver la TV en 3D algunos espectadores experimenten molestias como mareos, nauseas y dolores de cabeza. Si experimenta síntomas de este tipo, deje de ver la TV en 3D, quítese las gafas 3D y descanse. • Ver imágenes en 3D por un tiempo prolongado puede causar tensión ocular. Si experimenta astenopía, deje de ver la TV en 3D, quítese las gafas 3D y descanse. • Es responsabilidad de los adultos vigilar a los niños que estén utilizando la función 3D. Si se detectan situaciones de ojos cansados, dolores de cabeza, mareos o nauseas, impida que los niños sigan viendo la TV en 3D y oblígueles a descansar. • No utilice las gafas 3D para otros fines (como lentes de uso general, gafas de sol, gafas de protección, etc.) • No utilice la función 3D ni las gafas 3D mientras camina o se desplaza. El uso de la función 3D o de las gafas 3D mientras se desplaza puede provocar choques con objetos, tropiezos o caídas y causar daños personales serios. • Si desea disfrutar del contenido 3D, conecte un dispositivo 3D (receptor de AV o TV que admita 3D) al puerto HDMI OUT del reproductor utilizando un cable HDMI de alta velocidad. Colóquese las gafas 3D antes de reproducir el contenido 3D. • El reproductor genera la salida de señales 3D sólo a través del cable HDMI conectado al puerto HDMI OUT. • Debido a que la resolución de video en el modo de reproducción 3D es fija de acuerdo con la resolución del video 3D original, no puede cambiar la resolución a su gusto. • Es posible que algunas funciones como BD Wise, el ajuste del tamaño de la pantalla y el ajuste de la resolución es posible no funcionen correctamente en el modo de reproducción 3D. • Debe utilizar un cable HDMI de alta velocidad para la salida correcta de la señal 3D. • Colóquese a una distancia de al menos tres veces la anchura de la pantalla con respecto al TV al ver imágenes en 3D. Por ejemplo, si tiene una pantalla de 46 pulgadas, colóquese a 350 cm (138 pulgadas) de la pantalla. • Coloque la pantalla de video 3D a la altura de los ojos para conseguir la mejor imagen en 3D. • Si se conecta el reproductor a algunos dispositivos 3D, es posible que el efecto 3D no funcione debidamente. • Este reproductor no convierte contenido 2D en contenido 3D. • "Blu-ray 3D" y el logotipo de "Blu-ray 3D" son marcas comerciales de Blu-ray Disc Association. Copyright © 2014 Samsung Electronics Co.,Ltd. Todos los derechos reservados. Ninguna parte de este manual del usuario pueden reproducirse o copiarse sin la autorización previa por escrito de Samsung Electronics Co. Ltd. 3 Índice Información de seguridad Sistema...................................................... 16 Precauciones................................................ 2 Seguridad................................................... 16 Advertencia.................................................. 2 Almacenamiento y manejo de discos............ 3 Precauciones de manejo.............................. 3 Utilización de la función 3D........................... 3 Copyright..................................................... 3 Introducción Antes de utilizar este manual del usuario...... 4 Logotipos de discos que el reproductor puede reproducir.......................................... 5 Accesorios................................................... 6 Panel frontal................................................. 7 Panel posterior............................................. 7 Mando a distancia........................................ 7 Conexiones Conexión a un TV......................................... 8 Conexión a un sistema de audio................... 8 Conexión a un enrutador de red................... 9 Configuración Procedimiento de ajustes iniciales.............. 10 Menú de navegación.................................. 10 Acceso al menú Configuración................... 10 Pantalla...................................................... 10 Audio.......................................................... 12 Red............................................................ 13 4 Idioma........................................................ 16 General....................................................... 17 Soporte técnico.......................................... 17 Introducción Antes de utilizar este manual del usuario Tipos de disco y contenido que pueden reproducirse en el reproductor Soportes Reproducción de multimedia Reproducción de un disco grabado VIDEO comercial.................................................... 18 Reproducción de archivos en un dispositivo USB.......................................... 18 Reproducción de un disco con contenido grabado por el usuario............... 18 MÚSICA o del dispositivo AllShare a través PHOTO Reproducción de contenido de la PC del reproductor de discos Blu-ray............... 19 Control de reproducción de video............... 19 Control de reproducción de música............ 19 Reproducción de contenido fotográfico...... 21 Apéndice Solución de problemas............................... 21 Especificaciones......................................... 23 ✎✎ NOTA Tipo de disco Disco Blu-ray Disco Blu-ray 3D DVD-VIDEO DVD-RW DVD-R DVD+RW DVD+R CD-RW/-R, DVD-RW/-R, BD-RE/-R CD-RW/-R, DVD-RW/-R, BD-RE/-R Detalles BD-ROM o BD-RE/-R grabado en formato BD-RE. DVD-VIDEO, DVD+RW/DVD-RW(V)/DVD-R/+R grabados y finalizados o un soporte de almacenamiento USB que incluya contenido DivX, MKV, MP4. Música grabada en un disco CD-RW/-R, DVD-RW/-R, BD-RE/-R o en un soporte de almacenamiento USB que incluya contenido MP3 o WMA. Fotos grabadas en un disco CD-RW/-R, DVD-RW/-R, BD-RE/-R o en un soporte de almacenamiento USB que incluya contenido JPEG. `` `` `` `` `` Quizá el reproductor no pueda reproducir CD-RW/-R y DVD-R en todos los casos debido al tipo de disco o al estado de la grabación. Si no se ha grabado correctamente un disco DVD-RW /-R en formato de video DVD, no se podrá reproducir. El reproductor no reproducirá contenido grabado en un DVD-R con una velocidad de bits que supere los 10 Mbps. El reproductor no reproducirá contenido grabado en un BD-R o un dispositivo USB con una velocidad de bits que supere los 25 Mbps. Es posible que la reproducción no funcione en algunos tipos de discos o cuando se estén realizando operaciones específicas como el cambio de ángulo o el ajuste de la relación de aspecto. En la caja del disco se incluye información detallada sobre los discos. Consúltela en caso necesario. `` Cuando se reproduce un título de BD-J, la carga puede tardar más tiempo que un título normal o es posible que algunas funciones se ejecuten más lentamente. Tipos de disco que no se pueden reproducir en el reproductor • HD DVD • DVD-ROM/PD/ MV, etc • DVD-RAM • DVD-RW (Modo VR ) • Super Audio CD • CVD/CD-ROM/CDV/ (excepto CD Layer) CD-G/CD-I/LD (los CD-G reproducen sólo audio, no gráficos). • DVD-R de 3,9 GB de diseño personalizado (Authoring). Código de región Tanto los reproductores como los discos están codificados por región. Estos códigos regionales deben concordar para que el disco se reproduzca. De lo contrario, no se reproducirá. El número regional de este aparato viene indicado en su panel trasero. Tipo de Código de disco región a Disco Blu-ray b c DVDVIDEO Logotipos de discos que el reproductor puede reproducir Discos Blu-ray BD-LIVE Disco Blu-ray 3D DivX Area Norteamérica, Centroamérica, Sudamérica, Corea, Japón, Taiwán, Hong Kong y Sureste de Asia. Europa, Groenlandia, Territorios franceses, Oriente Próximo, África, Australia y Nueva Zelanda. India, China, Rusia, Asia Central y Sur. 1 EE.UU., territorios de EE.UU. y Canadá 2 Europa, Japón, Oriente Próximo, Egipto, Sudáfrica, Groenlandia 3 Taiwán, Corea, Filipinas, Indonesia, Hong Kong 4 México, Sudamérica, Centroamérica, Australia, Nueva Zelanda, Islas del Pacífico, El Caribe 5 Rusia, Europa del Este, India, mayor parte de África, Corea del Norte, Mongolia 6 China Sistema NTSC en EE.UU., Canadá, Corea, Japón Formatos admitidos Notas sobre la conexión USB • El reproductor admite soportes de almacenamiento USB, reproductores MP3, cámaras digitales y lectores de tarjetas USB. • El reproductor no admite nombres de carpetas o títulos que tengan más de 128 caracteres. • Es posible que algunos dispositivos USB/ externos HDD/cámaras digitales no sean compatibles con este reproducir. • El reproductor admite los sistemas de archivos FAT16, FAT32 y NTFS. • Conecte directamente los dispositivos USB al puerto USB del reproductor. La conexión a través del cable USB puede causar problemas de compatibilidad. • Si inserta más de un dispositivo de memoria en un lector de varias tarjetas puede que no funcione correctamente el lector. • El reproductor no admite el protocolo PTP. • No desconecte el dispositivo USB durante el proceso de “carga”. • Cuanto más alta sea la resolución, mayor tiempo tardará la imagen en mostrarse. • Este reproductor no puede reproducir archivos MP3 con DRM (Digital Rights Management, Gestión de derechos digitales) descargados de sitios comerciales. • El reproductor sólo admite video por debajo de 30 fps (fotogramas por segundo). • El reproductor sólo admite dispositivos de clase de almacenamiento masivo (MSC) USB como "pen drives" y HDD USB. (HUB no admitido.) • Es posible que algunos dispositivos HDD USB, lectores multitarjeta y "pen drives" no sean compatibles con este reproductor. • Si algún dispositivo USB requiere mucha energía, es posible que se vea limitado por el dispositivo de seguridad del circuito. • Si la reproducción desde un HDD USB es inestable, proporcione alimentación adicional conectando el HDD en la toma de corriente. Si el problema continúa, póngase en contacto con el fabricante del HDD USB. • SAMSUNG no se hace responsable de ningún daño en los archivos ni de la pérdida de datos. • El reproductor no admite archivos NTSF comprimidos, archivos "sparse" o archivos encriptados. • Puede reparar o formatear el dispositivo USB en su PC de sobremesa. (Sólo SO MS-Window) Soporte de archivos de video Extensión de archivo Contenedor Códec de video *.avi AVI MP4v3 DivX 3.11/4/5/6 H.264 BP/MP/HP *.mkv *.wmv MKV WMV (wmv9) *.mp4 MP4 *.mpg *.mpeg PS VC-1 AP H.264 BP/MP/HP VC-1 AP VC-1 SM MP4 (mp4v) H.264 BP/MP/HP MPEG1 MPEG2 H.264 BP/MP/HP Códec de audio MP3 Dolby Digital DTS WMA PCM MP3 Dolby Digital DTS WMA AAC MP1, 2 Dolby Digital DTS Resolución 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 5 •• Limitaciones -- Incluso cuando el archivo esté codificado con un códec compatible mencionado anteriormente, es posible que un archivo no pueda reproducirse si su contenido tiene un problema. -- No se garantiza la reproducción normal si la información del contenedor de archivos es erróneo o el archivo en sí está dañado. -- Los archivos que tienen una velocidad de bits/fotogramas más alta que el estándar es posible que funcione de forma interrumpida en la reproducción de sonido/video. -- La función de búsqueda (salto) no está disponible si la tabla del índice del archivo está dañada. •• Descodificador de video -- Admite hasta H.264 Nivel 4.1 ni AVCHD -- No admite H.264 FMO/ASO/RS, VC1 SP/MP/AP L4 -- MPEG4 SP, ASP :. : Por debajo de 1280 x 720: 60 fotogramas máx Por encima de 1280 x 720: 30 fotogramas máx -- No admite GMC 2 o superior •• Descodificador de audio -- Admite WMA 7, 8, 9 y STD -- No admite velocidad de muestreo WMA de 22050 Hz mono. -- AAC: Vel. máx. de muestreo: 96 Khz (8, 11, 12, 16, 22, 24, 32, 44,1, 48, 64, 88,2, 96) Vel. de bits máx.: 320 kbps Formatos de archivos de subtítulos DivX admitidos *.ttxt, *.smi, *.srt, *.sub, *.txt ✎✎ NOTA `` Algunos discos con formato DivX, MKV y MP4 no se pueden reproducir, dependiendo de la resolución de video y de la configuración de la velocidad de fotogramas. Soporte de archivo de imagen Extensión de archivo *.jpg *.jpeg *.jpe *.png 6 Contenedor *.mp3 MP3 *.wma WMA Códec de audio MP3 WMA Rango de soporte Resolución JPEG 15360x8640 PNG 15360x8640 AVCHD (Códec de video avanzado de alta definición) • Este reproductor puede reproducir discos con formato AVCHD. Estos discos se graban y se usan normalmente en videocámaras. • El formato AVCHD es un formato digital de alta resolución para videocámaras. • El formato MPEG-4 AVC/H.264 comprime imágenes con una eficacia mayor que el formato de compresión de imágenes convencional. • Algunos discos AVCHD utilizan el formato "x.v.Color". Este reproductor puede reproducir discos AVCHD que utilizan el formato "x.v.Color". • "x.v.Color" es una marca comercial de Sony Corporation. • "AVCHD" y el logotipo de AVCHD son marcas comerciales de Matsushita Electronic Industrial Co., Ltd. y Sony Corporation. ✎✎ NOTA `` Es posible que algunos discos con formato AVCHD no se reproduzcan, dependiendo de la condición de grabación. Los discos con formato AVCHD no tienen que finalizarse. `` “x.v.Color” ofrece una gama de colores más amplia que los discos DVD normales para videocámara. Accesorios Soporte de archivos de música Extensión de archivo Tipo Compruebe los accesorios suministrados que se incluyen a continuación. - * Velocidades de muestreo (en kHz) - 8, 11, 16, 22, 32, 44,1, 48 * Velocidades de bits: todas las velocidades de bits en el rango de 5 kbps a 355 kbps AUDIO BONUS VIEW Cable de HDMI Pilas (AAA) para el mando a distancia Manual del usuario HOME REPEAT A-B REPEAT SUBTITLE FULL SCREEN Mando a distancia Panel frontal BOTÓN REPRODUCIR/PAUSA BOTÓN STOP Mando a distancia Guía del mando a distancia Enciende y apaga el reproductor. BOTÓN ABRIR/CERRAR Encienda y apague el TV. Tras la configuración, le permite establecer la fuente de entrada en su televisor. Ajuste del volumen del TV. Para expulsar un disco. BOTÓN ENC/APAG Presione los botones numéricos para utilizar las opciones. Se usa para entrar en el menú del disco. Se presiona para saltar hacia adelante o hacia atrás. Se presiona para detener un disco. USB HOST ✎✎ NOTA BANDEJA DE DISCO SENSOR DE MANDO A DISTANCIA `` Cuando el reproductor muestra el menú del disco Blu-ray, no es posible iniciar el video presionando el botón Reproducir en el reproductor o en el mando a distancia. Para reproducir el video, debe seleccionar Reproducir video o Inicio en el menú del disco y presionar el botón v. `` Para actualizar el software del reproductor a través de la toma USB Host, debe utilizar una tarjeta de memoria USB. Panel posterior Se presiona para reproducir el disco. Se utiliza para acceder a diversas funciones de audio en un disco (Disco Blu-Ray/DVD). AUDIO HOME SUBTITLE Se presiona para usar el menú de herramientas. Se presiona para salir del menú. Vuelve al menú anterior. Se presiona para usar la función bonusview. BONUS VIEW REPEAT A-B REPEAT Permitte repetir la reproducción del disco A-B Instalación de las pilas !! HDMI OUT LAN DIGITAL AUDIO OUT ✎✎ NOTA `` Si el mando a distancia no funciona adecuadamente: • Compruebe la polaridad (+/– )de las pilas. Se presiona para cambiar el idioma de los subtítulos del disco Blu-ray/DVD. Se utiliza para ver la información de reproducción durante la reproducción de un disco Blu-ray/DVD. Se utiliza para seleccionar las opciones de menú y cambiar el valor del menú. Estos botones se utilizan para menús del reproductor y también para diversa funciones del disco Blu-ray. Se utiliza para entrar en el menú emergente / menú de títulos. Se presiona para buscar adelante o atrás en un disco. Se presiona para detener temporalmente un disco. Se presiona para ir al menú de inicio. FULL SCREEN Se presiona para utilizar la función de pantalla completa; durante la reproducción de discos Blu-ray/DVD, este botón no está operativo. Permite repetir un título, un capítulo, una pista o un disco. • Compruebe si las pilas se han agotado. • Compruebe si el sensor del mando a distancia está obstruido por algún tipo de obstáculo. • Compruebe si hay alguna luz fluorescente cerca. PRECAUCIÓN `` Deshágase de las pilas de acuerdo con la normativa medioambiental vigente. No las tire a la basura. `` No deseche las pilas en el fuego. `` No genere un cortocircuito, desarme o recaliente las pilas. `` Si las pilas se reemplazan de manera incorrecta existe peligro de explosión. Reemplácelas únicamente por el mismo tipo o un tipo equivalente. 7 Conexiones Conexión a un sistema de audio Conexión a un TV Conecte un cable HDMI desde la toma HDMI OUT de la parte trasera del producto a la toma HDMI IN del TV. -- No conecte el cable de alimentación a la toma de corriente hasta haber realizado el resto de conexiones. -- Cuando cambie las conexiones, apague todos los dispositivos antes de arrancar. Puede conectar el reproductor Blu-ray a un sistema de audio utilizando uno de los métodos que se ilustra a continuación. -- No conecte el cable de alimentación a la toma de corriente hasta haber realizado el resto de conexiones. -- Cuando cambie las conexiones, apague todos los dispositivos antes de arrancar. Método 1 Conexión a un receptor de AV que admita HDMI • Conecte un cable HDMI desde la toma HDMI OUT de la parte trasera del producto a la toma HDMI IN del receptor. • La mejor calidad (recomendado) Método 2 Conexión a un receptor de AV con Dolby Digital o descodificador de DTS Audio Video • Utilizando el cable coaxial (no suministrado), conecte el terminal de salida de audio digital coaxial del producto a la toma de entrada coaxial digital del receptor. • Buena calidad • Oirá sonido sólo a través de los dos altavoces delanteros con la salida digital definida en PCM. ✎✎ NOTA 8 `` Si utiliza un cable HDMI-a-DVI para conectar al dispositivo de visualización, también debe conectar la salida de audio digital del reproductor en el sistema de audio para escuchar el audio. `` Un cable HDMI genera la salida de video y audio digital, por tanto no necesita el cable de audio. `` Dependiendo del TV, es posible que no funcionen algunas resoluciones de salida de HDMI. Consulte el manual del usuario del TV. `` Cuando conecte el reproductor al televisor utilizando el cable HDMI o a un nuevo televisor y lo vaya a encender por primera vez, el reproductor define automáticamente la resolución de salida HDMI con el valor más alto admitido por el televisor. `` Es posible que un cable HDMI largo pueda causar ruido en pantalla. Si esto ocurre, defina Color profundo HDMI en Apagado. `` Si el producto está conectado al televisor en el modo de salida HDMI 720p, 1080i o 1080p, debe utilizar el cable HDMI de alta velocidad. `` HDMI genera únicamente una señal digital pura en el TV. Si el TV no admite HDCP (Protección de contenido digital de ancho de banda alto), aparecen interferencias en pantalla. Método 1 Audio Método 2 Audio Conexión a un enrutador de red Puede conectar el reproductor a un enrutador de red utilizando uno de los métodos que se ilustran a continuación. Para utilizar la función de red de AllShare, debe conectar la PC a la red como es muestra en las ilustraciones. La conexión puede ser con cable o inalámbrica. Red inalámbrica Red de cable Enrutador inalámbrico Módem de banda ancha (con enrutador enrutador integrado) Servicio de banda ancha O ✎✎ NOTA `` Si el enrutador inalámbrico admite DHCP, el reproductor puede utilizar DHCP o una dirección IP estática para conectar a la red inalámbrica. `` Defina el enrutador inalámbrico en modo de infraestructura. No se admite el modo Ad-hoc. Enrutador Servicio de banda ancha Módem de banda ancha ✎✎ NOTA Servicio de banda ancha `` No se permite el acceso a Internet al servidor de actualización de software de Samsung, dependiendo del enrutador que utilice o la política del proveedor de servicios de Internet. Para obtener información adicional, póngase en contacto con el proveedor de servicios de Internet. `` Para usuarios de DSL, utilice el enrutador para realizar una conexión de red. `` El reproductor sólo admite los siguientes protocolos de seguridad inalámbrica: - WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES) `` Seleccione un canal en el enrutador inalámbrico que no se esté actualmente utilizando. Si el canal definido para el enrutador inalámbrico lo está utilizando actualmente otro dispositivo cercano, esto provocará interferencias y fallos en la comunicación. `` Si selecciona el modo puro de alto rendimiento (Greenfield) 802.11n y el tipo de cifrado en el enrutador se define en WEP, TKIP o TKIP-AES (WPS2Mixed), el reproductor no admitirá una conexión en conformidad con las nuevas especificaciones de certificación Wi-Fi. `` La LAN inalámbrica, por su naturaleza, puede causar interferencias, dependiendo de las condiciones de servicio (rendimiento del enrutador, distancia, obstáculo, interferencia por otros dispositivos de radio, etc). 9 Configuración Procedimiento de ajustes iniciales • El menú de inicio no aparecerá si no configura los ajustes iniciales. • La OSD (presentación en pantalla) puede cambiar en este reproductor tras actualizar la versión de software. • Los pasos de acceso pueden diferir dependiendo del menú seleccionado. • Una vez que finalice el proceso de carga de este producto, Se pueden utilizar los botones del panel y del mando a distancia. Una vez conectado el reproductor al TV, encienda el TV y el reproductor. Cuando encienda el reproductor por primera vez, la pantalla de ajustes iniciales del reproductor aparece en el TV. El procedimiento de ajustes iniciales permite establecer el idioma de la OSD y de los menús, la relación de aspecto (tamaño de pantalla), el tipo de red y conectar el reproductor a la red. ✎✎ NOTA `` El menú de inicio no aparecerá si no configura los ajustes iniciales ajuste iniciales excepto en el caso. `` Si presiona el botón AZUL(D) durante la configuración de red, puede acceder al menú de inicio incluso sin completar la configuración de red. `` Al volver al menú de inicio, se cancelará automáticamente el modo de pantalla completa. `` Si desea ver de nuevo la pantalla de configuración inicial para realizar cambios, presione el botón @ del panel frontal del reproductor durante más de 5 segundos si no hay ningún disco insertado. Con esto se reinicia el reproductor con sus ajustes predeterminados. `` Una vez que finalice el proceso de carga de este producto, puede utilizar la función HDMI-CEC. 10 Acceso al menú Configuración • Menú de Inicio 6 `` Si desea utilizar la función Anynet+(HDMI-CEC), siga las instrucciones que se incluye a continuación. 1) Conecte el reproductor a un TV Samsung compatible con Anynet+(HDMI-CEC) utilizando el cable HDMI. 2) Establezca la función Anynet+(HDMI-CEC) tanto en el TV como en el reproductor. 3) Establezca el TV en el procedimiento de configuración inicial. `` Si se deja el reproductor en modo de parada por más de 5 minutos sin usarse, se activará en el TV un protector de pantalla. Si el reproductor se deja en el modo de protector de pantalla por más de 25 minutos, se apagará automáticamente. HOME 1 2 3 4 REPEAT A-B REPEAT Bandeja de disco vacía 8 App 1 App 2 App 3 App 4 App 5 Más Screen Mirroring Cambiar dispositivo 9 Selecciona Música. Selecciona Config. 4 Selecciona Cambiar dispositivo. 5 Selecciona Screen Mirroring. 6 Selecciona Fotos. 7 Selecciona Rep. disco. 3 8 Selecciona aplicaciones. 4 0 Selecciona Más aplicaciones. FULL SCREEN de inicio. Botón RETURN : Vuelve al menú anterior. Botón v (ENTRAR) / DIRECCIÓN : Mueve el cursor o selecciona un elemento. Selecciona la opción actualmente seleccionada. Confirma el ajuste. Botón EXIT : Se presiona para salir del menú. 2 7 3 Botón HOME : Se presiona para ir al menú VIEW Música 2 1 BONUS Videos Selecciona Vidéos. SUBTITLE 2 Fotos 1 Menú de navegación AUDIO 1 Rep. disco ✎✎ NOTA Config. 3 4 5 `` Las opciones Vídeos, Fotos y Música requieren la inserción en el reproductor de un disco apropiado o la conexión al reproductor de un dispositivo flash USB. Para acceder al menú y submenús de configuración, siga estos pasos: 1. Presione el botón POWER. Aparecerá el menú de inicio. 2. Presione los botones ▲▼ ◄► hasta seleccionar Config. y, a continuación, presione el botón v. 3. Presione los botones ▲▼ para seleccionar el submenú que desee y, a continuación, presione el botón v. 4. Presione los botones ▲▼ para seleccionar el elemento que desee y, a continuación, presione el botón v. 5. Presione el botón EXIT para salir del menú. ✎✎ NOTA `` Los pasos de acceso pueden diferir dependiendo del menú seleccionado. La OSD (presentación en pantalla) puede cambiar en este reproductor tras actualizar la versión de software. Pantalla Puede configurar diversas opciones de pantalla como relación de aspecto de TV, resolución, etc. Ajustes 3D Selecciona si reproducir un disco Blu-ray con contenido 3D en modo 3D. ✎✎ NOTA `` En algunos discos 3D, para detener un video durante la reproducción 3D, presione una vez el botón 5 El video se detiene y se desactiva la opción del modo 3D. Para cambiar la selección de la opción 3D al reproducir una película 3D, presione una vez el botón 5. Aparece el menú Blu-ray. Presione de nuevo el botón 5 y seleccione Config. 3D en el menú Blu-ray. `` Dependiendo del contenido y de la posición de la imagen en la pantalla de TV, es posible que vea barras negras verticales en el lado izquierdo, en el lado derecho o en ambos. Formato de TV Dependiendo del tipo de televisión, se puede ajustar el ajuste de tamaño de la pantalla. ✎✎ NOTA `` Dependiendo del tipo de disco, es posible que no estén disponibles algunas relaciones de altura/anchura. `` Si selecciona una relación de aspecto y una opción que sea diferente de la pantalla de televisión, es posible que la imagen aparezca distorsionada. BD Wise (sólo reproductores Samsung) BD Wise es la función de interconectividad más reciente de Samsung.Cuando conecte entre sí un reproductor Samsung y un TV Samsung con BD Wise a través de HDMI, y BD Wise esté activado en el reproductor y el TV, el reproductor genera la salida de video con la resolución y la velocidad de fotogramas del disco. ✎✎ NOTA `` Cuando BD Wise está activada, el ajuste de resolución se define por defecto en BD Wise y BD Wise aparece en el menú de resolución. `` Si el reproductor se conecta a un dispositivo que no admite BD Wise, no puede utilizar la función BD Wise. `` Para un funcionamiento apropiado de BD Wise, defina tanto el menú BD Wise del reproductor como del TV en Activado. Resolución • Reproducción de DVD Permite definir la resolución de salida de la señal de video de Componente y HDMI en Auto, 1080p, 1080i, 720p, 480p. El número indica el número de líneas de video por fotograma. La i y la p indican respectivamente el rastreo interlazado y progresivo. Cuanto más líneas, más alta será la calidad. Resolución de acuerdo con el modo de salida • Reproducción de discos Blu-ray / contenido electrónico / contenido digital Salida Configuración HDMI / conectado Modo HDMI Contenido Discos electrónico Blu-ray / Contenido digital BD Wise Resolución del disco Blu-ray 1080p Auto Resolución máx. de la entrada de TV Resolución máx. de la entrada de TV 1080p@60F 1080p@60F Fotogr. Película : Automático (24Fps) 1080p@24F 1080p@24F 1080i 1080i 1080i 480p 480p 480p 1080p@60F (Fotogramas de video : Off) 720p 720p 720p Salida Configuración HDMI / conectado Modo HDMI BD Wise 480i Auto Resolución máx. de la entrada de TV 1080p 1080i 720p 480p ✎✎ NOTA 1080p 1080i 720p 480p `` Si el TV conectado no admite Fotogr. Película o la resolución seleccionada, aparecerá el mensaje “Si no aparecen imágenes después de seleccionar “Sí”, espere 15 segundos y regresará a la resolución anterior. ¿Desea cambiar la resolución?”. Si selecciona Si, la pantalla del TV aparecerá en blanco por 15 segundos y la resolución volverá automáticamente a la resolución anterior. `` Si la pantalla se queda en blanco después de haber cambiado la resolución, retire todos los discos y mantenga presionado el botón @ en la parte delantera del reproductor por más de 5 segundos. Todos los ajustes recuperan sus valores de fábrica. Siga los pasos de la página anterior para acceder a cada modo y seleccione la configuración de pantalla que admita su televisor. `` Cuando se recuperan los ajustes predeterminados de fábrica, todos los datos de usuario almacenados en la BD se borran. `` El disco Blu-ray debe tener la función de 24 fotogramas para poder utilizar en el reproductor el modo Fotogr. película (24Fps). Fotograma (24 fps) El ajuste de la función Fotograma (24Fps) en Automático le permite ajustar la salida HDMI del reproductor en 24 fotogramas por segundo para obtener una mejor calidad de imagen. Puede disfrutar de la función Fotograma (24Fps) sólo en un TV que admita esta velocidad de fotogramas. Sólo puede seleccionar Fotogr. Película cuando el reproductor esté en los modos de resolución de salida HDMI 1080p. Formato color HDMI Permite definir el formato de espacio de color para la salida HDMI para que coincida con las capacidades del dispositivo conectado (TV, monitor, etc). Color profundo HDMI Permite definir el producto para que genere el video HDMI con color profundo. Color profundo proporciona una reproducción del color más precisa con una mayor profundidad del color. Modo progresivo Permite mejorar la calidad de la imagen al ver DVDs. 11 Audio Salida Digital Permite seleccionar el formato de salida de audio digital adecuado para su TV o receptor de AV. Para más detalles, consulte la selección de salida digital. Selección de salida digital Configuración Receptor HDMi Conexión PCM Dolby Digital Dolby Digital Plus Flujo de datos de audio en Dolby TrueHD disco Blu-ray DTS DTS-HD HRA DTS-HD MA Flujo de datos de audio en DVD Definición para disco Blu-ray 12 PCM Dolby Digital DTS Cualquiera Bitstream (Sin procesar) PCM Hasta 7,1 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales Coaxial PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales PCM 2 canales Descodifica al mismo tiempo el audio de la función principal y el flujo de datos de audio BONUSVIEW en audio PCM y añade los efectos de sonido de navegación. Receptor HDMi PCM Dolby Digital Dolby Digital Plus Dolby TrueHD Coaxial PCM 2 canales Dolby Digital Dolby Digital Dolby Digital Bitstream (DTS recodificado) Receptor HDMi u Coaxial DTS recodificado DTS recodificado DTS recodificado DTS recodificado DTS DTS DTS recodificado DTS-HD HRA DTS DTS recodificado DTS-HD MA DTS DTS recodificado PCM 2 canales PCM 2 canales Dolby Digital Dolby Digital DTS DTS Genera sólo la salida del flujo de datos del audio de la función principal de forma que el receptor de AV pueda descodificar el flujo de bits de audio. No oirá el audio de BONUSVIEW ni los efectos de sonido de navegación. Bitstream (Dolby D recodificado) Receptor de AV que admita HDMi u Coaxial Dolby Digital recodificado * Dolby Digital recodificado * Dolby Digital recodificado * Dolby Digital recodificado * Dolby Digital recodificado * Dolby Digital recodificado * Dolby Digital recodificado * PCM 2 canales PCM 2 canales Dolby Digital Dolby Digital DTS DTS Descodifica el audio de la función principal y el flujo de datos de audio de BONUSVIEW en audio PCM y añade los efectos de sonido de navegación, a continuación recodifica el audio de PCM en flujo de bits DTS. Descodifica el audio de la función principal y el flujo de datos de audio de BONUSVIEW en audio PCM y añade los efectos de sonido de navegación, a continuación recodifica el audio de PCM en flujo de bits de Dolby digital. ** Si el flujo de origen es de 2 canales, no se aplica el ajuste de “Dolby D Recodificado”. Los discos Blu-ray pueden incluir tres flujos de audio: -- Audio de función principal: la pista sonora de la función principal. -- Audio BONUSVIEW: pista sonora adicional como los comentarios del director o del actor. -- Efectos de sonido de navegación: cuando se elige la navegación de menú, pueden oírse los efectos de sonido de navegación. Los efectos de sonido de navegación son diferentes en cada disco Blu-ray. ✎✎ NOTA `` Asegúrese de seleccionar la salida digital correcta o es posible que no oiga nada o sólo un ruido alto. `` Si el dispositivo HDMI (receptor de AV, TV) no es compatible con formatos comprimidos (Dolby digital, DTS), la señal de audio se genera como PCM. `` Los DVD normales no tienen audio BONUSVIEW ni efectos de sonido de navegación. `` Algunos discos Blu-ray no tienen audio BONUSVIEW ni efectos de sonido de navegación. `` Si reproduce pistas sonoras de audio MPEG, la señal de salida de audio se genera como PCM independientemente de las selecciones de salida digital (PCM o Bitstream). `` Si el TV no es compatible con los formatos multicanal comprimidos (Dolby Digital, DTS), es posible que el reproductor genere la salida de audio submezcado PCM de 2 canales incluso aunque haya seleccionado Bitstream (recodificado o sin procesar) en el menú de configuración. `` Si el TV no es compatible con velocidades de muestreo PCM superiores a 48 kHz, es posible que el reproductor genere la salida de audio de submuestreo PCM de 48 kHz aunque haya definido Submuestreo PCM en Apagado. Submuestreo PCM Permite elegir convertir señales PCM de 96 Khz en 48 Khz antes de que pasen a un amplificador. Elija Encendido si el amplificador o el receptor no son compatibles con una señal de 96 Khz. Compresión Dinámica Permite aplicar el control de rango dinámico a al audio Dolby Digital, Dolby Digital Plus y Dolby TrueHD. • Auto: Controla automáticamente el rango dinámico del audio Dolby TrueHD, basándose en la información de la banda sonora Dolby TrueHD. También activa el control de rango dinámico para Dolby Digital y Dolby Digital Plus. • Apagado: deja el rango dinámico sin comprimir, lo que le permite oír el sonido original. • Encendido: activa el control de rango dinámico paras los tres formatos. Los sonidos más callados son más altos y se reduce el volumen de los sonidos altos. Modo Downmixing Permite seleccionar el método de Downmix de varios canales que es compatible con el sistema estéreo. Puede elegir en el reproductor Downmix en estéreo normal o en estéreo compatible con Surround. Red Para iniciar la conexión de red para el reproductor, siga estos pasos: 1. En el menú Inicio, ▲▼ ◄► para seleccionar Config. y, a continuación, presione el botón v. 2. Presione los botones ▲▼ hasta seleccionar Red y, a continuación, presione el botón v. 3. Presione los botones ▲▼ hasta seleccionar Configuración de red y, a continuación, presione el botón v. 4. Presione los botones ▲▼ hasta seleccionar Tipo de red y, a continuación, presione el botón v. 5. Presione los botones ▲▼ hasta seleccionar Cable o Inalámbrico y, a continuación, presione el botón v. 6. Vaya a la siguiente sección. Configuración de la conexión de red Antes de empezar, póngase en contacto con su proveedor de servicios de Internet para ver si su dirección IP es estática o dinámica. Si es dinámica y está utilizando una conexión de red con cable o inalámbrica, recomendamos utilizar los procedimientos de configuración que se describen a continuación. Si está conectando a una red de cable, conecte el reproductor al enrutador utilizando un cable LAN antes de iniciar el procedimiento de configuración. Si está conectando a una red inalámbrica, desconecte la conexión de red de cable antes de empezar. Para iniciar la configuración de la conexión de red, siga estos pasos: Red de cable ĞĞ Con cable - Automática 1. En la pantalla de inicio, seleccione Config. y, a continuación, presione el botón v. 2. Seleccione Red y, a continuación, presione el botón v. 3. Seleccione Configuración de red y, a continuación, presione el botón v. 4. Seleccione Cable en la pantalla de configuración de red y, a continuación, presione el botón v. 5. Seleccione el botón Conectar y, a continuación, presione el botón v. El producto detecta la conexión de cable, verifica la conexión de red y, a continuación, se conecta a la red. ĞĞ Con cable - Manual Si tiene una dirección IP estática o el procedimiento automático no funciona, tendrá que definir manualmente los valores de configuración de red. Siga los pasos 1 y 2 de Con cable - Automática y, a continuación, siga estos pasos: 1. Seleccione Estado de red. El reproductor busca una red y, a continuación, muestra el mensaje de error en la conexión. 2. En la parte inferior de la pantalla, seleccione Ajustes IP y, a continuación, presione el botón v. Aparece la pantalla de configuración de IP. 3. Seleccione el campo Ajustes IP y, a continuación, presione el botón v. 4. Seleccione Ingresar en forma manual y, a continuación, presione el botón v. 5. Seleccione un valor para introducir (Dirección IP, por ejemplo) y, a continuación, presione el botón v. Utilice el teclado numérico del mando a distancia para introducir los números del valor. Utilice los botones ◄► del mando a distancia para moverse entre campo y campo dentro de un valor. Una vez que haya terminado con un valor, presione el botón v. 6. Presione el botón ▲ o ▼ para ir a otro valor y, a continuación, ingrese los números de dicho valor siguiendo las instrucciones del paso 5. 7. Repita los pasos 5 y 6 hasta haber introducido todos los valores. ✎✎ NOTA ĞĞ Wireless - Automatic 1. En la pantalla de inicio, seleccione Config. y, a continuación, presione el botón v. 2. Seleccione Red y, a continuación, presione el botón v. 3. Seleccione Configuración de red y, a continuación, presione el botón v. 4. Seleccione Inalámbrico en la pantalla de configuración de red y, a continuación, presione el botón v. El reproductor busca y muestra una lista de redes disponibles. Configuración de red Seleccione su tipo de red Tipo de red Red inalámbrica `` Puede obtener los valores de red del proveedor de Internet. 8. Cuando termine de introducir todos los valores, a continuación, presione el botón RETURN o EXIT. El reproductor verifica la conexión de red y, a continuación, se conecta a la red. Red inalámbrica Puede configurar la conexión de una red inalámbrica de cuatro formas: -- Inalámbrica automática -- Inalámbrica manual -- WPS(PBC) -- WPS(PIN) Cuando configure la conexión de red inalámbrica, se desconectará cualquier dispositivo de red inalámbrico actualmente conectado a través del reproductor o, en caso aplicable, la conexión con cable actual del mismo. Inalámbrico Agregar red WPS(PBC) Buscar Puede conectar su Reproductor de Blu-ray a Internet. Seleccione qué redes inalambricas desea utilizar. m Mover " Seleccionar ' Regresar 5. Seleccione la red que desee y, a continuación, presione el botón v. 6. En la pantalla de seguridad, ingrese el código de seguridad o la contraseña de acceso de red. Ingrese directamente los números utilizando los botones numéricos del mando a distancia. Ingrese letras seleccionándolas con el botón de flecha y presionando el botón v. 7. Una vez hecho, resalte Listo y, a continuación, presione el botón v. El reproductor verifica la conexión de red y, a continuación, se conecta a la red. 8. Una vez completada la verificación, seleccione Aceptar y, a continuación, presione el botón v. ✎✎ NOTA `` Debe ser capaz de buscar un código de seguridad o una palabra de acceso en una de las pantallas de configuración utilizadas para configurar el enrutador o el módem. 13 ĞĞ Inalámbrica manual Si tiene una dirección IP estática o el procedimiento automático no funciona, tendrá que definir manualmente los valores de configuración de red. 1. Siga las directrices de Inalámbrica automática hasta el paso 5. 2. El reproductor busca una red y, a continuación, muestra el mensaje de error en la conexión. 3. En la parte inferior de la pantalla, seleccione Ajustes IP y, a continuación, presione el botón v. Aparece la pantalla de configuración de IP. 4. Seleccione el campo Ajustes IP y, a continuación, presione el botón v. 5. Seleccione Ingresar en forma manual y, a continuación, presione el botón v. 6. Seleccione un valor para introducirlo (Dirección IP, por ejemplo) y, a continuación, presione el botón v . Utilice el teclado numérico del mando a distancia para introducir los números del valor. Utilice los botones ◄► del mando a distancia para moverse entre campo y campo dentro de un valor. Una vez que haya terminado con un valor, presione el botón v. 7. Presione el botón ▲ o ▼ para ir a otro valor y, a continuación, ingrese los números de dicho valor siguiendo las instrucciones del paso 6. 8. Repita los pasos 6 y 7 hasta haber introducido todos los valores. ✎✎ NOTA `` Puede obtener los valores de red del proveedor de Internet.. 9. Una vez hecho, a continuación, presione el botón RETURN o EXIT. Aparecerá la pantalla de seguridad. 14 10.En la pantalla de seguridad, ingrese el código de seguridad o la contraseña de acceso de red. Ingrese directamente los números utilizando los botones numéricos del mando a distancia. Ingrese letras seleccionando una letra con los botones ▲▼◄► y, a continuación, presionando el botón v. 11.Una vez finalizado, seleccione Listo en la parte derecha de la pantalla y, a continuación, presione el botón v. El reproductor verifica la conexión de red y, a continuación, se conecta a la red. 12.Una vez que el reproductor verifique la red, seleccione Aceptar y, a continuación, presione el botón v. ĞĞ WPS(PBC) 1. En la pantalla de inicio, seleccione Config. y, a continuación, presione el botón v. 2. Seleccione Red y, a continuación, presione el botón v. 3. Seleccione Configuración de red y, a continuación, presione el botón v. 4. Seleccione Inalámbrico en la pantalla de configuración de red y, a continuación, presione el botón v. 5. Presione el botón ▲▼ del mando a distancia y, a continuación, presione el botón ◄► para seleccionar WPS(PBC). 6. Presione el botón v del mando a distancia. Aparece el mensaje "Pulse el botón PBC". 7. Presione el botón WPS(PBC) del enrutador antes de que transcurran dos minutos. El reproductor adquiere automáticamente todos los valores de configuración de red que necesita y se conecta a la red. Aparece la pantalla de estado de red. El reproductor se conecta a la red después de verificar la conexión de red. ĞĞ WPS(PIN) Antes de empezar, abra el menú de configuración del enrutador en el de la PC y acceda a la pantalla con el campo de entrada de PIN de WPS. 1. En la pantalla de inicio, seleccione Config. y, a continuación, presione el botón v. 2. Seleccione Red y, a continuación, presione el botón v. 3. Seleccione Configuración de red y, a continuación, presione el botón v. 4. Seleccione Inalámbrico en la pantalla de configuración de red y, a continuación, presione el botón v. El reproductor busca y muestra una lista de redes disponibles. 5. Seleccione la red que desee y, a continuación, presione el botón ► 6. Seleccione WPS(PIN) y, a continuación, presione el botón v. Aparece el diálogo de PIN. 7. Ingrese el PIN en el campo de entrada de WPS PIN en la pantalla de configuración del enrutador y guarde la pantalla. ✎✎ NOTA `` Póngase en contacto con el fabricante del enrutador para obtener instrucciones sobre la forma de acceder a las pantallas de configuración del enrutador o consulte el manual del usuario del enrutador. `` Para conexión WPS, defina el cifrado de seguridad del enrutador inalámbrico en AES. Definir el cifrado de seguridad WEP no admite conexión WPS. Prueba de red Utilice este menú para comprobar si está funcionando o no la conexión de red. Estado de red Compruebe si se ha establecido una conexión a la red y a Internet. Wi-Fi directa La función Wi-Fi directa le permite conectar dispositivos Wi-Fi directa al reproductor y entre sí utilizando una red "igual a igual" sin un enrutador inalámbrico. ✎✎ NOTA `` Es posible que algunos dispositivos Wi-Fi directa no admitan la función AllShare si se han conectado a través de Wi-Fi directa. S este es el caso, se recomienda cambiar el método de conexión de red entre dispositivos. `` Las transmisiones Bluetooth pueden interferir con la señal de Wi-Fi directa. Antes de utilizar la función Wi-Fi directa, recomendamos encarecidamente desactivar la función Bluetooth en los dispositivos móviles activos. 1. Encienda el dispositivo Wi-Fi directa y active su función Wi-Fi directa. 2. En la pantalla de inicio, seleccione Config. y, a continuación, presione el botón v. 3. Seleccione Red y, a continuación, presione el botón v. 4. Seleccione Wi-Fi directa y, a continuación, presione el botón v. Aparecen los dispositivos Wi-Fi directa que se pueden conectar. 5. Tiene tres formas de completar la conexión Wi-Fi: • A través del dispositivo Wi-Fi. • A través del reproductor utilizando PBC. • A través del reproductor utilizando PIN. A continuación se aborda cada uno de ellos. A través del dispositivo Wi-Fi. 1. En el dispositivo Wi-Fi, siga el procedimiento en el dispositivo para conectar a otro dispositivo Wi-Fi directa. Consulte el manual del usuario del dispositivo para obtener instrucciones. 2. Una vez completado el procedimiento, debe ver un mensaje emergente en la pantalla del TV que indique que un dispositivo que admite Wi-Fi directa ha solicitado conectar. Seleccione Aceptar y, a continuación, presione el botón v para aceptar. 3. Aparece el mensaje de intento de conexión seguido del mensaje de conexión realizada. Cuando se cierra, debe ver en la lista de la pantalla de Wi-Fi directa el dispositivo como conectado. A través del reproductor utilizando PBC. 1. Seleccione el dispositivo Wi-Fi directa que desee conectar a este reproductor y, a continuación, presione el botón v. Aparece la ventana de PBC/PIN. 2. Seleccione PBC y, a continuación, presione el botón v. Aparece el diálogo de PBC. 3. Presione el botón PBC en el dispositivo de Wi-Fi directa antes de que transcurran 2 minutos. 4. Aparece el mensaje de intento de conexión seguido del mensaje de conexión realizada. Cuando se cierra, debe ver en la lista de la pantalla de Wi-Fi directa el dispositivo como conectado. A través del reproductor utilizando PIN. 1. Seleccione el dispositivo Wi-Fi directa que desee conectar a este reproductor y, a continuación, presione el botón v. Aparece la ventana de PBC/PIN. 2. Seleccione PIN y, a continuación, presione el botón v. Aparece el diálogo de PIN. 3. Anote el código PIN de la ventana emergente y, a continuación, introdúzcalo en el campo apropiado del dispositivo WiFi directa que desee conectar. 4. Aparece el mensaje de intento de conexión seguido del mensaje de conexión realizada. Cuando se cierra, debe ver en la lista de la pantalla de Wi-Fi directa el dispositivo como conectado. ✎✎ NOTA `` La conexión de red con cable o inalámbrica actual se desconectará cuando utilice la función Wi-Fi directa. `` Los archivos de texto, como los archivos con la extensión .TXT o .DOC, no se mostrarán cuando utilice la función Wi-Fi directa. Screen Mirroring La función Screen Mirroring permite ver la pantalla de su smartphone o tableta Android en el TV conectado al reproductor Blu-ray. 1. En el menú Inicio, ▲▼ ◄► para seleccionar Screen Mirroring y, a continuación, presione el botón v. Aparece la ventana emergente Screen Mirroring. 2. Inicie AllShare Cast en el dispositivo. 3. En el dispositivo, busque el nombre del reproductor Blu-ray en la lista de dispositivos disponibles y selecciónelo. 4. El TV mostrará un PIN. Ingrese el PIN en el dispositivo. 5. El TV muestra un mensaje de conexión (por ejemplo, Conectando a Android_92gb...) y muestra el mensaje de que está conectado. 6. Trascurridos unos segundos, la pantalla de su dispositivo aparece en la pantalla de TV. 7. Para detener Screen Mirrorin, presione el botón EXIT o RETURN del mando a distancia o desactive la función de duplicación de pantalla de su smartphone. ✎✎ NOTA `` Puede conectar a un dispositivo compatible con AllShare Cast. Tenga en cuenta que conectar un dispositivo de este tipo puede que no sea totalmente compatible según el fabricante. Para más información sobre el soporte de conexión móvil, consulte el sitio web del fabricante. `` Cuando esté utilizando la función Screen Mirroring, puede producirse interrupciones de video o caídas del audio, según el entorno. `` Las transmisiones Bluetooth pueden interferir con la señal de Screen Mirroring. Antes de utilizar la función Screen Mirroring, recomendamos encarecidamente desactivar la función Bluetooth en el smartphone o en el dispositivo inteligente (tableta, etc.). Nombre dispos. La función Nombre de dispositivo le permite cambiar el nombre del reproductor seleccionando en el cuadro de lista de nombres de dispositivos. Conexión a Internet BD-Live Define si permitir la conexión de Internet cuando se utiliza el servicio BD-LIVE. • Permitir (todo) : se permitirá la conexión a Internet para todos los contenidos de BD-LIVE. • Permitir (sólo válido) : la conexión a Internet sólo estará permitida para contenidos de BDLIVE que contengan un certificado válido. • Restringir : no se permitirá ninguna conexión a Internet para ningún contenido BD-LIVE. ✎✎ NOTA `` ¿Qué es un certificado válido? Cuando el reproductor utiliza BD-LIVE para enviar los datos del disco y solicitar al servidor certificar el disco, el servidor utiliza los datos transferidos para comprobar si el disco es válido y envía el certificado de vuelta al reproductor. `` Es posible que se restrinja la conexión a Internet mientras utilice contenidos de BD-LIVE you are using BD-LIVE contents. Uso de la BD-LIVE™ Una vez que el reproductor se conecta a la red, puede disfrutar de diverso contenido de servicios relacionados con películas utilizando un disco compatible con BD-LIVE. 1. Compruebe el tamaño de la memoria restante. El dispositivo de memoria debe tener al menos 1 GB de espacio libre en disco para alojar los servicios de BD-LIVE. 2. Inserte un disco Blu-ray que admita BDLIVE. 3. Seleccione un elemento entre los diversos contenidos de servicios BD-LIVE que facilita el fabricante del disco. ✎✎ NOTA `` La forma de utilizar BD-LIVE y el contenido proporcionado puede diferir dependiendo del fabricante del disco. 15 Uso de la función AllShare AllShare le permite reproducir archivos de música, vídeo y fotos ubicados en su PC o un dispositivo de almacenamiento de red en el reproductor. Para usar AllShare, debe conectar el reproductor al PC a través de la red (consulte las páginas 13 y 16) Para utilizar AllShare con su PC, debe instalar el software de AllShare en el PC. Si tiene o un dispositivo de almacenamiento de red, puede usar AllShare sin software adicional. Para descargar el software de AllShare 1. Visite www.samsung.com 2. Haga clic en Atención al cliente, introduzca el número de producto del reproductor en el campo que aparece y haga clic en Producto. 3. En la siguiente pantalla, haga clic en Centro de descarga en el menú Descargas. 4. Haga clic en Software en la página siguiente. 5. Haga clic en el icono en la línea de AllShare en Archivo para iniciar la descarga. Sistema Configuración inicial Al utilizar los ajustes iniciales, puede definir el idioma, la configuración de red, etc. Para más información sobre la función de configuración inicial, consulte la sección Configuración inicial de este manual de usuario. (Consulte de la página 10.) . 16 Inicio rápido Permite definir que el reproductor se encienda rápidamente reduciendo el tiempo de arranque. ✎✎ NOTA `` Si esta función se define en Encendido, aumentará el consumo de alimentación de espera. Anynet+ (HDMI-CEC) Anynet+ es una función práctica que ofrece un funcionamiento enlazado con otros reproductores Samsung con la función Anynet+. Para utilizar esta función, conecte este reproductor a un TV Samsung con un cable HDMI. Puede utilizar este reproductor utilizando el mando a distancia del TV Samsung e iniciar la reproducción del disco simplemente presionando el botón REPRODUCIR ( ) del mando a distancia del TV. Para más información, consulte el manual de usuario del TV. ✎✎ NOTA `` La función no está disponible si el cable HDMI no admite CEC. `` Si el televisor Samsung tiene un logotipo Anynet+ admite la función Anynet+. `` Dependiendo del TV, es posible que no funcionen algunas resoluciones de salida de HDMI. Consulte el manual del usuario del TV. `` Una vez que se apague el producto, al desconectar y conectar el cable de alimentación se activa automáticamente. Enseguida, se desactiva automáticamente unos 15 segundos para restablecer la conexión Anynet+. `` En algunos productos de TV, si se conecta a este producto con la función Anynet+, si se enciende el TV puede aparecer el mensaje emergente de advertencia indicando que no se ha encontrado ninguna conexión. Aun así, la conexión Anynet+ se establece correctamente y está disponible para su uso. Gestión de datos BD Seguridad Permite gestionar el contenido descargado desde un disco Blu-ray que admita el servicio BD-LIVE y que se haya almacenado en un dispositivo de memoria Flash conectado. Puede comprobar la información del dispositivo incluido el tipo de almacenamiento, borrar los datos de BD o cambiar el dispositivo de memoria Flash. El PIN por defecto es 0000. Ingrese el PIN por defecto para acceder a la función de seguridad si no ha creado su propio PIN. Después de haber accedido a la función de seguridad por primera vez, cambie el PIN utilizando la función Cambiar PIN. `` En el modo de memoria externa, la reproducción del disco se detendrá si desconecta el dispositivo USB en medio de la reproducción. impide la reproducción de discos Blu-ray con una calificación igual o superior a una calificación de edad específica a menos que se ingrese el PIN. ✎✎ NOTA `` El reproductor admite los sistemas de archivos FAT16, FAT32 y NTFS.y se recomienda utilizar dispositivos USB que admitan el protocolo USB 2.0, con una velocidad de lectura/escritura de 4 MB/seg o superior. `` Es posible que no esté operativa la función de reanudación de reproducción tras formatear el dispositivo de almacenamiento. `` La memoria total disponible para la gestión de datos de BD puede diferir, dependiendo de las condiciones. Video de pago DivX® Permite ver los códigos de registro VOD de DivX® VOD para comprar y reproducir contenido DivX® VOD. Idioma Puede seleccionar el idioma que prefiera para el menú en pantalla, menú del disco, audio, subtítulos. ✎✎ NOTA `` El idioma seleccionado sólo aparecería si el disco lo incluyese. Clasif. padres BD Clasif. padres DVD Esta función está disponible junto con los discos DVD que han sido asignados al nivel. Esta función le ayuda a controlar los tipos de disco DVD que su familia ve. Seleccione el nivel de calificación que desee establecer. Un número mayor indica que el programa está destinado únicamente a adultos. Por ejemplo, si selecciona hasta el Nivel 6, no se reproducirán los discos que contengan Nivel 7 y 8. Un número mayor indica más maduro contenido. Cambiar Código permite cambiar el PIN de 4 dígitos utilizado para acceder a las funciones de seguridad. Si olvida la contraseña 1. Retire el disco. 2. Mantenga presionado por 5 segundos o más el botón @ del panel frontal. Todos los ajustes volverán a sus ajustes de fábrica. ✎✎ NOTA `` Cuando se recuperan los ajustes predeterminados de fábrica, todos los datos de usuario almacenados en la BD se borrará. General Zona horaria Puede especificar la zona horaria aplicable a su área. Soporte técnico Actualización del software Este menú de actualización de software permite actualizar el software del reproductor para mejoras del rendimiento o servicios adicionales. En línea Para actualizar En línea, siga estos pasos: 1. En el menú del reproductor, vaya a Config. > Soporte técnico > Actualización del software. 2. Seleccione En línea y, a continuación, presione el botón v Aparece el mensaje Conectando al servidor. 3. Aparecerá un mensaje emergente si está disponible una actualización. 4. Si selecciona Sí, se inicia el proceso de descarga. (Nunca encienda el reproductor durante la actualización.) 5. Una vez completada la actualización, el reproductor se reiniciará automáticamente. ✎✎ NOTA `` La actualización se completa cuando el reproductor se apaga y se enciende de nuevo por sí mismo. `` Nunca apague o encienda manualmente el reproductor durante el proceso de actualización. `` Samsung Electronics no será responsable legal de averías en el reproductor causadas por una conexión a Internet inestable o por negligencia del consumidor durante la actualización de software. `` La bandeja del disco debe estar vacía al actualizar el software utilizando la toma En línea. Por USB Para actualizar por USB, siga estos pasos: 1. Visite www.samsung.com/bluraysupport. 2. Descargue en su computadora el archivo zip de actualización de software USB más reciente. 3. Descomprima el archivo zip en su ordenador. Debe tener un solo archivo RUF con el mismo nombre que el archivo zip. 4. Guarde el archivo RUF en un disco. Recomendamos utilizar un CD-R o DVD-R. 5. Asegúrese de que no haya ningún disco en el reproductor e inserte la unidad flash USB en el puerto USB del reproductor 6. En el menú del reproductor, vaya a Config. > Soporte técnico > Actualización del software. 7. Seleccione Por USB. ✎✎ NOTA `` La bandeja del disco debe estar vacía al actualizar el software utilizando la toma USB Host. `` Una vez finalizada la actualización del software, compruebe los detalles del software en el menú Actualización del software. `` No apague el reproductor durante la actualización del software. Puede provocar una avería en el reproductor. `` Las actualizaciones de software que utilizan el terminal USB Host deben realizarse sólo con una tarjeta de memoria flash USB. Notificación de actualización automática Si ha conectado el reproductor a la red y activa la notificación de actualización automática, el reproductor notifica automáticamente si está disponible una nueva versión del software para el reproductor. Para activar la notificación de actualización automática, siga los pasos que se incluyen a continuación: 1. Seleccione Notificación de actualización automática. y pulse el botón v. 2. Pulse los botones ▲▼ para seleccionar Encendido y, a continuación, pulse el botón v. Si hay disponible una nueva versión de software, el reproductor avisa con un mensaje emergente. Contacto con Samsung Proporciona información de contacto para obtener asistencia sobre el reproductor. Térms. de acuerdo de servicios Vea la declinación de responsabilidades general respecto al contenido y servicios de terceros. Rest. Todos los ajustes volverán a los valores predeterminados excepto para los ajustes de red. 1. Para actualizar el firmware, seleccione Encendido en el diálogo emergente. El reproductor se apaga automáticamente, se reinicia e inicia la descarga (Nunca encienda aquí el reproductor manualmente.) 2. Aparecerá la ventana de progreso de la actualización. 3. Una vez completada la actualización, el reproductor se reiniciará automáticamente. ✎✎ NOTA `` La actualización se completa cuando el reproductor se apaga y se enciende de nuevo por sí mismo. `` Nunca apague o encienda manualmente el reproductor durante el proceso de actualización. `` Samsung Electronics no será responsable legal de averías en el reproductor causadas por una conexión a Internet inestable o por negligencia del consumidor durante la actualización de software. 17 Reproducción de multimedia Reproducción de un disco grabado comercial 1. Presione el botón 8 para abrir la bandeja de disco. 2. Coloque el disco en la bandeja con el lado de la etiqueta hacia arriba. 3. Presione el botón 8 para cerrar la bandeja de disco. La reproducción se inicia automáticamente. Reproducción de archivos en un dispositivo USB Existen dos métodos que puede utilizar para reproducir o ver archivos multimedia de un dispositivo USB a través del reproductor. Método 1 1. Encienda el reproductor. 2. Conecte el dispositivo USB al puerto USB de la parte frontal del reproductor. Aparece el mensaje emergente Nuevo dispositivo. Rep. disco Fotos Videos 123 Fotos Bandeja de disco vacía Música Nuevo dispositivo. Música > Mover " Ingresar ' Regresar ✎✎ NOTA App 5 Más Screen Mirroring Cambiar dispositivo Config. `` Si no aparece este mensaje emergente, vaya al Método 2. 18 ✎✎ NOTA `` Incluso aunque el reproductor muestre carpetas para todo tipo de contenido, sólo mostrará los archivos del tipo de contenido seleccionado en el paso 3. Por ejemplo, si selecciona música, sólo podrá ver archivos de música. Puede cambiar esta selección volviendo a la pantalla Fotos, videos y música y, a continuación, yendo al paso 3 del Método 2 que se incluye a continuación. 4. Si es necesario, utilice los botones ▲▼◄► para seleccionar una carpeta y, a continuación, presione el botón v. 5. Seleccione un archivo para verlo o reproducirlo y, a continuación, presione el botón v. 6. Presione el botón RETURN para salir de una carpeta o el botón EXIT para volver a la pantalla de inicio. 7. Vaya a las páginas 19~21 para obtener instrucciones sobre la forma de controlar la reproducción de videos, música e imágenes del dispositivo USB. Método 2 Videos App 1 App 2 App 3 App 4 3. Utilice los botones ▲▼ para seleccionar Fotos, Videos, Música y, a continuación, presione el botón v. Aparece la pantalla Fotos, videos y música con el contenido del dispositivo. Según la forma en que se organice el contenido, verá carpetas, archivos individuales o ambos. 1. Encienda el reproductor. 2. Conecte el dispositivo USB al puerto USB de la parte frontal del reproductor. Seleccione Cambiar dispositivo y, a continuación, pulse el botón ▲▼ para seleccionar USB y. Presione el botón v. Rep. disco Fotos Videos Música Cambiar dispositivo No hay disco 123 Bandeja de disco vacia a App 1 App 2 App 3 App 4 App 5 Más Cerrar Screen Mirroring Cambiar dispositivo Config. 3. Utilice los botones ▲▼◄► para seleccionar Fotos, Videos, Música en la pantalla de inicio y, a continuación, presione el botón v. Aparece la pantalla Fotos, videos y música con el contenido del dispositivo. Según la forma en que se organice el contenido, verá carpetas, archivos individuales o ambos. ✎✎ NOTA `` Incluso aunque el reproductor muestre carpetas para todo tipo de contenido, sólo mostrará los archivos del tipo de contenido seleccionado en el paso 3. Por ejemplo, si selecciona música, sólo podrá ver archivos de música. Puede cambiar esta selección volviendo a la pantalla Fotos, videos y música y repitiendo el paso 3. 4. Si es necesario, utilice los botones ▲▼◄► para seleccionar una carpeta y, a continuación, presione el botón v. 5. Utilice los botones ▲▼◄► para seleccionar un archivo para verlo o reproducirlo y, a continuación, presione el botón v. 6. Presione el botón RETURN para salir de la carpeta o el botón EXIT para volver a la pantalla de inicio. 7. Vaya a las páginas 19~21 para obtener instrucciones sobre la forma de controlar la reproducción de videos, música e imágenes del dispositivo USB. ✎✎ NOTA `` Si inserta el disco al reproducir el dispositivo USB, el modo de dispositivo cambia automáticamente a "Disco. Reproducción de un disco con contenido grabado por el usuario Es posible reproducir archivos multimedia grabados en discos Blu-ray, DVD o CD. 1. Coloque un disco grabado por el usuario en la bandeja de disco con la etiqueta hacia arriba y cierre la bandeja. . 2. Utilice los botones ◄► para seleccionar el tipo de contenido que desee ver o reproducir - Fotos, Videos, Música, a continuación presione el botón v. ✎✎ NOTA `` Incluso aunque el reproductor muestre carpetas para todo tipo de contenido, sólo mostrará los archivos del tipo de contenido seleccionado en el paso 2. Por ejemplo, si selecciona música, sólo podrá ver archivos de música. Puede cambiar esta selección volviendo a la pantalla Fotos, videos y música y repitiendo el paso 2. 3. Aparece una pantalla con el contenido del dispositivo. Según la forma en que se organice el contenido, verá carpetas, archivos individuales o ambos. 4. Si es necesario, utilice los botones ▲▼◄► para seleccionar una carpeta y, a continuación, presione el botón v. 5. Utilice los botones ▲▼◄► para seleccionar un archivo para verlo o reproducirlo y, a continuación, presione el botón v. 6. Presione el botón RETURN una o más veces para salir de la pantalla actual, de una carpeta o para volver a la pantalla de inicio. Presione el botón EXIT para volver directamente a la pantalla de inicio. 7. Vaya a las páginas 19~21 para obtener instrucciones sobre la forma de controlar la reproducción de videos, música e imágenes de un disco. Reproducción de contenido de la PC o del dispositivo AllShare a través del reproductor de discos Blu-ray PC Reproductor de discos Blu-ray Reproducción de archivos de la PC Conexión de AllShare 1. Conecte el reproductor de discos Bluray, su PC o el dispositivo compatible con AllShare a la misma red inalámbrica. 2. Siga las indicaciones del manual de instrucciones/instalación del software de AllShare para configurar los dispositivos y archivos para reproducirlos o verlos. 3. Seleccione Cambiar dispositivo en la pantalla de inicio del reproductor y, a continuación, pulse el botón v. En la lista de dispositivos conectados de AllShare que aparece, seleccione la PC u otro dispositivo compatible con AllShare y, a continuación, presione el botón v. 4. Utilice los botones ◄► para seleccionar el tipo de contenido que desee ver o reproducir - Fotos, Videos, Música, a continuación presione el botón v. ✎✎ NOTA `` Incluso aunque el reproductor muestre carpetas para todo tipo de contenido, sólo mostrará los archivos del tipo de contenido seleccionado en el paso 2. Por ejemplo, si selecciona música, sólo podrá ver archivos de música. Puede cambiar esta selección volviendo a la pantalla Fotos, videos y música y repitiendo el paso 4. 5. Aparece una pantalla con el contenido del dispositivo. Según la forma en que se organice el contenido, verá carpetas, archivos individuales o ambos. 6. Si es necesario, utilice los botones ▲▼◄► para seleccionar una carpeta y, a continuación, presione el botón v. 7. Utilice los botones ▲▼◄► para seleccionar un archivo para verlo o reproducirlo y, a continuación, presione el botón v. 8. Presione el botón RETURN una o más veces para salir de la pantalla actual, de una carpeta o para volver a la pantalla de inicio. Presione el botón EXIT para volver directamente a la pantalla de inicio. 9. Vaya a las páginas 19~21 para obtener instrucciones sobre la forma de controlar la reproducción de videos, música e imágenes de un disco. Control de reproducción de video Puede controlar la reproducción del contenido de video de un disco Blu-ray , DVD, CD, USB, o PC. Dependiendo del disco, es posible que no estén disponibles algunas funciones descritas en este manual. Durante la reproducción de discos Blu-ray/ DVD, este botón no está operativo. Botones del mando a distancia utilizados para reproducción de video 2 1 AUDIO HOME SUBTITLE Botones relacionados con la reproducción El reproductor no reproduce sonido en modo de búsqueda, lento o paso. • Para volver a la reproducción a velocidad normal, presione el botón 6. Botón 6 Botón 5 Botón 7 BONUS VIEW REPEAT A-B REPEAT FULL SCREEN Inicia la reproducción. Detiene la reproducción. Hace una pausa en la reproducción. Durante la reproducción, presione el botón 3 o 4. Reproducción a Cada vez que presione el botón 3 cámara rápida o 4, cambiará la velocidad de reproducción. Reproducción a cámara lenta En modo de pausa, presione el botón 4. Cada vez que presione el botón 4, cambiará la velocidad de reproducción. En modo de pausa, presione el Reproducción botón 7. por fotogramas Cada vez que presione el botón 7, aparece un nuevo fotograma. Salto en reproducción Durante la reproducción, presione el botón 1 o 2. Cada vez que presione el botón 1 o 2, el disco va al capítulo o al archivo anterior o siguiente. Uso del menú de disco, menú de título, menú emergente y lista de títulos Botón DISC MENU Durante la reproducción, presione este botón para iniciar la función del menú del disco. Botón TITLE MENU Durante la reproducción, presione este botón para iniciar la función del menú de título. Botón POPUP MENU Durante la reproducción, presione este botón para iniciar la función del menú emergente. Control de reproducción de música Puede controlar la reproducción del contenido de música de un disco Blu-ray , DVD, CD, USB, o PC. Botones del mando a distancia utilizados para reproducción de música 1 4 2 3 1 AUDIO HOME SUBTITLE 5 6 Botones NUMÉRICOS (sólo CD de audio (CD-DA): Durante la reproducción de la lista de reproducción, presione el número de pista que desee. Se reproduce la pista seleccionada. BONUS VIEW REPEAT A-B REPEAT FULL SCREEN 19 2 Omitir: durante la reproducción, presione el botón 1 o 2 para ir a la página anterior o siguiente de la lista de reproducción. 3 5 botón: detiene una pista. 4 5 6 Reproducción rápida (sólo CD de audio (CD-DA)) Durante la reproducción, presione el botón 3 o 4. Cada vez que presione el botón 3 o 4, cambiará la velocidad de reproducción. 6 botón: reproduce la pista actualmente seleccionada. TRACK 001 List. Repr. 1/6 Herramientas TRACK 001 Modo de repetición ? Apagado\05:57 TRACK 002 Copiar 04:27 > Mover < Ajustar ' Regresar TRACK 003 + 00:08 / 05:57 TRACK 004 TRACK 005 TRACK 006 CD " Pausa c Seleccionar 04:07 03:41 03:17 03:35 Herramientas ' Regresar 2. Presione los botones ◄► para seleccionar Pista, Todo, Mezcla o Apagado. 3. Presione el botón v. Apagado ( 20 Música Las canciones se reproducen en el orden en que se grabaron. ) Pista Se repite la canción actual. )Mezcla La opción aleatoria reproduce canciones en orden aleatorio. ) Todo 1/2 Página TRACK 001 TRACK 001 TRACK 002 02:38 02:38 TRACK 003 TRACK 004 02:38 02:38 TRACK 006 TRACK 005 02:38 02:38 02:38 02:38 TRACK 008 TRACK 007 1. Durante la reproducción, presione el botón TOOLS. ( 1. Para ir a la lista de música, presione el botón 5 o RETURN. Aparece la pantalla de la lista de música. Pausa: hace una pausa en la pista. Repetición de un CD de audio (CD-DA)/MP3 ( Lista de reproducción Se repiten todas las canciones. TRACK 010 TRACK 009 02:38 02:38 CD a Cambiar dispositivo c Seleccionar Herramientas ( ) Salt. de pág ' Regresar 2. Presione los botones ▲▼◄► para ir a la pista que desee y, a continuación, presione el botón AMARILLO (C). Aparece una marca en la pista. Repita este procedimiento para seleccionar pistas adicionales. 3. Para eliminar una pista de la lista, vaya a la pista y, a continuación, presione de nuevo el botón AMARILLO (C). La marca desaparece de la pista. 4. Una vez hecho, presione el botón v. Las pistas seleccionadas aparecen en el lado derecho de la pantalla. El reproductor reproduce la primera pista. 5. Para cambiar la lista de reproducción, pulse el botón @ o botón RETURN para volver a la lista de música. Repita los pasos 2, 3 y 4. 6. Para cancelar la lista de reproducción y volver a la pantalla de inicio, pulse el botón RETURN o EXIT. ✎✎ NOTA `` Puede crear una lista de reproducción de hasta 99 pistas en un CD de audio (CD-DA). `` Si elimina todas las pistas de la lista de reproducción y pulsa el botón v el reproductor mostrará y reproducirá todas las pistas del disco. Copia Permite copiar contenido de archivos de audio desde un disco de datos a un dispositivo USB/ disco duro. 1. Abra la bandeja del disco. Coloque el CD de audio (CD DA) en la bandeja y ciérrela. Inserte un dispositivo USB en la toma USB del frontal del producto. 2. Resione los botones ▲▼◄► para ir a la pista que desee y, a continuación, presione el botón AMARILLO (C). Aparece una marca en la pista. Repita este procedimiento para seleccionar pistas adicionales. 3. Para eliminar una pista de la lista, vaya a la pista y, a continuación, presione de nuevo el botón AMARILLO (C). La marca desaparece de la pista. 4. Una vez hecho, presione el botón TOOLS, seleccione el botón Copiar utilizando los botones ▲▼ y, a continuación, presione el botón v. Aparece el diálogo de copia. 5. Presione los botones ▲▼ hasta seleccionar el dispositivo para almacenar los archivos copiados y, a continuación, presione el botón v. ✎✎ NOTA `` No desconecte el dispositivo mientras se encuentra en curso la copia. 6. Si desea cancelar la copia de la pista, presione el botón v y, a continuación, seleccione Sí. Seleccione No para continuar copiando. 7. Una vez que se finalice la copia, aparece el mensaje "Copia completa". Presione el botón v para volver a la pantalla de reproducción. ✎✎ NOTA `` Es posible que esta función no se admita en algunos discos. `` En la pantalla de copia, también puede elegir Seleccionar todo y Deseleccionar todos. -- Utilice Seleccionar todo para seleccionar todas las pistas y. Con esto se cancelan las selecciones individuales de pistas. -- Utilice Deseleccionar todos para cancelar la selección de todas las pistas seleccionadas de una vez. Copiar un disco para USB Permite copiar contenido de vídeo/fotos/música desde un disco de datos a un dispositivo USB/ disco duro. 1. Abra la bandeja del disco. Coloque el disco en la bandeja y ciérrela. Inserte un dispositivo USB en la toma USB del frontal del producto. Aparece la ventana emergente de nuevo dispositivo. 2. Presione el botón ▲, a continuación, presione el botón ◄► para seleccionar Bluray, DVD o CD. 3. Utilice los botones ▲▼ para seleccionar Fotos, Videos, Música y, a continuación, presione el botón v. Aparece la pantalla Fotos, videos y música con el contenido del dispositivo. Según la forma en que se organice el contenido, verá carpetas, archivos individuales o ambos. ✎✎ NOTA `` Incluso aunque el reproductor muestre carpetas para todo tipo de contenido, sólo mostrará los archivos del tipo de contenido seleccionado en el paso 3. Por ejemplo, si selecciona música, sólo podrá ver archivos de música. Puede cambiar esta selección volviendo a la pantalla Fotos, videos y música y repitiendo el paso 3. 4. Con la pantalla de reproducción abierta, Utilice los botones ▲▼ ◄► para seleccionar Videos, Fotos, Música y, presione de nuevo el botón AMARILLO (C). Aparece una marca a la izquierda del elemento deseado. 5. Repita el paso 4 para seleccionar y marcar un elemento adicional que desee. 6. Para eliminar de la lista el elemento deseado, pulse de nuevo el botón AMARILLO (C). Se borra la marca del elemento deseado. 7. Una vez hecho, pulse el botón TOOLS y seleccione la opción de Copiar a USB ▲▼ y, a continuación, pulse el botón v. Aparece el diálogo emergente Copiar a USB. 8. Utilice los botones ▲▼ hasta seleccionar el dispositivo para almacenar los archivos copiados y, a continuación, pulse el botón v. ✎✎ NOTA `` No desconecte el dispositivo mientras se encuentra en curso la copia. 9. Si desea cancelar la copia de la pista, pulse el botón v y, a continuación, seleccione Sí. Seleccione No para continuar copiando. 10.Una vez que se finalice la copia, aparece el mensaje "Copia completada". Pulse el botón v ppara volver a la pantalla de reproducción. ✎✎ NOTA `` Es posible que esta función no se admita en algunos discos. `` En la pantalla de copia, también puede elegir Seleccionar todo y Deseleccionar todos. -- Utilice Seleccionar todo para seleccionar todos los elementos. Con esto se cancelan las selecciones individuales de elementos. - Utilice Deseleccionar todos para cancelar la selección de todos los elementos seleccionados al mismo tiempo. Reproducción de contenido fotográfico Puede reproducir contenido fotográfico de un Disco Blu-ray, DVD, CD, USB o PC. Utilización del menú de herramientas Durante la reproducción, presione el botón TOOLS. Inic. vis. aut/ Detener presentacion Se selecciona para iniciar o detener la presentación. Música de fondo Se selecciona para escuchar música mientras se ve una presentación. Veloc. de presentación Se selecciona para ajustar la velocidad de la presentación. Zoom Se selecciona para ampliar la imagen actual. (Se amplía hasta 4 veces.) Girar Se selecciona para girar la imagen. (Esto hará girar la imagen a la derecha o a la izquierda.) Informacíon Muestra la información de la imagen. ✎✎ NOTA `` Dependiendo del disco o del dispositivo de almacenamiento, es posible que no funcione el menú Herramientas. `` Para activar la función de música de fondo, el archivo de foto debe estar en el mismo medio de almacenamiento que el archivo de música. No obstante, la calidad del sonido puede verse afectada por la velocidad de bits del archivo MP3, el tamaño de la foto y el método de codificación. `` No es posible ampliar el subtítulo ni el gráfico PG en el modo de pantalla completa. Apéndice Solución de problemas Antes de solicitar servicio técnico, intente las siguientes soluciones. PROBLEMA SOLUCIÓN El mando a distancia no funciona. • Compruebe las pilas del mando a distancia. Quizás haya que cambiarlas. • Utilice el mando a distancia a una distancia de no más de 6.1m del reproductor. • Extraiga las pilas y mantenga presionado uno o más botones por varios minutos para descargar el microprocesador del mando a distancia y reinicializarlo. Introduzca las pilas de nuevo y compruebe si funciona el mando a distancia. El disco no se reproduce. • Asegúrese de que el disco esté cargado con el lado de la etiqueta hacia arriba. • Compruebe el código regional del disco Blu-ray/DVD. No aparece el menú del disco. • Asegúrese de que el disco tenga menús de disco. Aparece en pantalla un mensaje de prohibición. • Este mensaje aparece cuando se presiona un botón no válido. • El software del disco Blu-ray/DVD no admite esta función (ej. ángulos). • Ha solicitado un título, un número de capítulo o un punto de búsqueda que está fuera de rango. El modo de reproducción no es el seleccionado en el menú de configuración. • Puede que algunas de las funciones seleccionadas en el menú de configuración no funcionen si el disco no está codificado con estas funciones. No se puede cambiar la dimensión de la pantalla. • La relación de pantalla se fija en el disco Blu-ray/DVD. • No hay ningún problema con el reproductor. No hay audio. • Asegúrese de haber seleccionado la salida Dolby correcta en el menú de opciones de audio. La pantalla está en blanco. • Si la salida HDMI se define en una resolución que no sea compatible con el TV (por ejemplo, 1080p), es posible que no pueda ver ninguna imagen en el TV. • Presione el botón @ (del panel frontal) por más de 5 segundos sin ningún disco cargado. Todos los ajustes volverán a los ajustes originales de fábrica. • Cuando se recuperan los ajustes predeterminados de fábrica, todos los datos de BD de usuario almacenados se borrarán. 21 PROBLEMA SOLUCIÓN PIN olvidado • Presione el botón @ (del panel frontal) por más de 5 segundos sin ningún disco cargado. Todos los ajustes que contenían una contraseña volverán a los ajustes originales de fábrica. No utilice esta opción a menos que sea absolutamente necesario. • Cuando se recuperan los ajustes predeterminados de fábrica, todos los datos de BD de usuario almacenados se borrarán. La imagen produce ruidos o está distorsionada. • Compruebe si el disco tiene suciedad o está rayado. • Limpie el disco. No hay salida de HDMI. • Compruebe la conexión entre el TV y el terminal de HDMI del reproductor. • Compruebe si el TV admite la resolución de entrada de HDMI 480p, 720p, 1080i o 1080p. Pantalla de salida de HDMI anormal. • Si aparecen interferencias en pantalla, significa que el TV no admite HDCP (protección de contenido digital de ancho de banda alto). Si experimenta otros problemas. • Vaya al contenido y busque la sección del manual del usuario con las explicaciones sobre el problema actual y siga de nuevo el procedimiento. • Si el problema persiste, póngase en contacto con el centro de servicio técnico autorizado de Samsung más cercano. Función AllShare Puedo ver carpetas compartidas a través de AllShare, pero no puedo ver los archivos. • AllShare sólo muestra archivos de Video, Foto y Música. Otros tipos de archivos no se muestran. El video se reproduce de forma intermitente. • Compruebe si la red es estable. • Compruebe si el cable de red está debidamente conectado y si la red no está sobrecargada. • La conexión inalámbrica entre el servidor y el dispositivo compatible con AllShare y el reproductor es inestable. Compruebe la conexión. La conexión AllShare entre el reproductor y la PC es inestable. • La dirección IP en la misma subred debe ser única. Si no lo son, la interferencia de IP puede causar este fenómeno. • Compruebe si tiene activado un cortafuegos. Si así es, desactivar la función de cortafuegos. 22 PROBLEMA BD-LIVE SOLUCIÓN No puedo conectar al servidor de BD-LIVE. • Compruebe si el dispositivo de memoria USB está conectado al reproductor. • Compruebe si la conexión de red es correcta utilizando la función Estado de la red. • El dispositivo de memoria debe tener al menos 1GB de espacio libre en disco para alojar el servicio de BD-LIVE. Puede comprobar el tamaño disponible en Gestión de datos BD. • Compruebe si la opción Conexión a Internet BD-LIVE está definido en Permitir (todos). • Si fallo todo lo anterior, póngase en contacto con el proveedor de contenido o actualice el firmware más reciente en el reproductor. Al utilizar el servicio de BD-LIVE, se produce un error. • El dispositivo de memoria debe tener al menos 1GB de espacio libre en disco para alojar el servicio de BD-LIVE. Puede comprobar el tamaño disponible en Gestión de datos BD. ✎✎ NOTA `` Cuando se recuperan los ajustes predeterminados de fábrica, todos los datos de BD de usuario almacenados se borrarán Reparaciones Si se pone en contacto con nosotros para reparar el reproductor, podría aplicársele una tarifa de administración si: 1. Solicita que un ingeniero acuda a su casa y el producto no tiene ningún defecto. 2. Trae la unidad al centro de reparaciones y el producto no tiene ningún defecto. Antes de acudir a su casa o de realizar cualquier trabajo en el reproductor, le informaremos del importe de la tarifa de administración. Le recomendamos que lea el manual a fondo, que busque una solución en línea en www. samsung.com, o que se ponga en contacto con el Centro de atención al cliente de Samsung antes de mandar a reparar el reproductor. Especificaciones Generales USB HDMI Salida de audio Red Requisitos de alimentación Mexico : AC 110-127V c.a. 50/60Hz (Otros paises : 100-240V) Consumo eléctrico 9.8 W Peso 1.2 Kg Dimensiones 360 (An.) X 196 (Pr.) X 39 (Al.) mm Rango de temperatura de servicio De +5°C a +35°C Rango de humedad de servicio De 10 % a 75 % Type A USB 2.0 Salida de CC 5V 0.5A Max. Video 2D : 1080p, 1080i, 720p, 480p 3D : 1080p, 720p Audio PCM, Bitstream Salida de audio digital Coaxial Ethernet 100BASE - TX Terminal LAN inalámbrica Integrado Seguridad WEP (OPEN/SHARED) WPA-PSK (TKIP/AES) WPA2-PSK (TKIP/AES) WPS(PBC) Admitido -- No se admiten velocidades de red iguales o inferiores a 10 Mbps. -- El diseño y las especificaciones están sujetos a cambio sin aviso. -- El peso y dimensiones son aproximados. 23 Aviso de conformidad y compatibilidad NO TODOS los discos son compatibles • Sujeto a las restricciones que se describen a continuación y a las indicadas a lo largo de todo el manual, incluida la sección Tipo de disco y características de este manual de usuario, los tipos de discos que pueden reproducirse son: discos BD-ROM comerciales pregrabados, DVD-VIDEO y CD de audio (CD-DA); discos BD-RE/-R, DVD-RW/-R ; y discos CD-RW/-R. • Otros discos diferentes a los anteriores no podrán reproducirse en este reproductor. Y es posible que algunos de los discos anteriormente mencionados no puedan reproducirse debido a una o más de las razones indicadas a continuación • Samsung no puede garantizar que este reproductor reproduzca todos los discos que lleven los logotipos de BD-ROM, BD-RE/-R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R y CD-RW/-R, y es posible que este reproductor no responda a todas las órdenes de funcionamiento ni pueda utilizar las funciones de todos los discos. Estos y otros problemas de compatibilidad de disco y funcionamiento del reproductor con discos con nuevos formatos y con formatos existentes son posibles por las siguientes razones : -- Blu-ray es un formato nuevo en continua evolución y es posible que este reproductor no pueda comprender todas las funciones de los discos Blu-ray ya que algunas funciones pueden ser opcionales, es posible que se hayan añadido nuevas funciones al formato Blu-ray tras la producción de este reproductor y algunas funciones disponibles están sujetas a una disponibilidad ulterior. -- No todas las versiones del nuevo formato y del formato existente del disco están admitidas en este reproductor; -- Formatos de disco nuevos y existentes pueden ser revisados, modificados, actualizados, mejorados y complementados; -- Algunos discos son producidos de manera que permiten utilizar de forma específica o limitada algunas operaciones y funciones durante la reproducción; -- Algunos discos que llevan los logotipos de BD-ROM, BD-RE/-R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R y CD-RW/-R puede ser discos aún no estandarizados; -- Es posible que algunos discos no puedan reproducirse dependiendo de su estado físico o las condiciones de grabación; -- Pueden producirse problemas y errores durante la creación de software para disco Blu-ray, DVD o la fabricación de discos; -- Este reproductor funciona de forma diferente que el reproductor de DVD estándar u otro equipo de AV; o -- Por las razones reseñadas a lo largo del manual del usuario y por otras razones descubiertas y divulgadas por el servicio de atención al cliente de SAMSUNG. • Si encuentra problemas de compatibilidad en el disco o problemas de funcionamiento del reproductor, póngase en contacto con el servicio de atención al cliente de SAMSUNG. También puede ponerse en contacto con el servicio de atención al cliente de SAMSUNG para obtener posibles actualizaciones sobre este reproductor. • Para obtener información adicional sobre las restricciones de reproducción y la compatibilidad de los discos, consulte las secciones Precauciones, Antes de leer este Manual del usuario, Tipos de discos y características y Antes de reproducir de este manual de usuario. 24 • Para la salida de barrido progresivo de reproductores de discos Blu-ray: LOS CONSUMIDORES DEBEN TENER EN CUENTA QUE NO TODOS LOS EQUIPOS DE TELEVISIÓN SON TOTALMENTE COMPATIBLES CON ESTE PRODUCTO Y PUEDEN CAUSAR LA APARICIÓN DE INTERFERENCIAS DE LA IMAGEN. EN CASO DE PROBLEMAS CON LA IMAGEN DE BARRIDO PROGRESIVO, SE RECOMIENDA QUE EL USUARIO CAMBIE LA CONEXIÓN A UNA SALIDA CON ‘DEFINICIÓN ESTÁNDAR’. SI TUVIESE ALGUNA DUDA SOBRE LA COMPATIBILIDAD DE NUESTRO EQUIPO DE TV CON ESTE PRODUCTO, PÓNGASE EN CONTACTO CON EL SERVICIO DE ATENCIÓN AL CLIENTE. Protección de copia • Debido a que AACS (Advanced Access Content System) es un sistema aprobado como sistema de protección de contenido para formato de disco Blu-ray, similar al uso de CSS (Content Scramble System) para formato DVD, se imponen algunas restricciones sobre la reproducción, salida de señal analógica, etc., de contenido protegido mediante AACS. El funcionamiento de esta unidad y las restricciones pueden variar dependiendo de la fecha de compra ya que dichas restricciones pueden haberse adoptado y/o modificado mediante AACS tras la producción de este aparato. Además, la marca BD-ROM y BD+ se utilizan adicionalmente como un sistema de protección de copia para de disco Blu-ray, que impone ciertas restricciones incluidas restricciones de reproducción para la marca BD-ROM y/o el contenido protegido de BD+. Para obtener información adicional sobre AACS, la marca BDROM, BD+ o este producto, póngase en contacto con el servicio de atención al cliente de SAMSUNG. • Muchos discos Blu-ray/DVD están codificados con la protección de copia. Por esta razón, debe conectar sólo el reproductor directamente al TV, no a un aparato de vídeo. La conexión al aparato de vídeo puede causar la distorsión de la imagen proveniente de discos Blu-ray/ DVD con protección de copia. • Bajo las leyes de Copyright de EE.UU. y las leyes de Copyright de otros países, la grabación, el uso, la distribución o la revisión de programas de televisión, cintas de vídeo, discos Blu-ray, DVD y otros materiales no autorizados, pueden estar sujeto a responsabilidad civil o criminal. • Aviso de Cinavia: Este producto utiliza tecnología Cinavia para limitar el uso de copias no autorizadas de algunas películas de producción comercial, videos y sus bandas sonoras. Cuando se detecta el uso de una copia no autorizada, aparecerá un mensaje y se interrumpirá la reproducción o la copia. Información adicional sobre la tecnología Cinavia se facilita en el Centro de información al cliente en línea de Cinavia en http://www.cinavia.com. Para solicitar información adicional sobre Cinavia por correo, envíe una tarjeta con su dirección postal a: Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, EE.UU. Este producto incorpora tecnología de propietario bajo licencia de Verance Corporation y está protegido mediante la patente en EE.UU. 7.369.677 y otras patentes en EE.UU. y en otros países pendientes, así como por copyright y la protección de secreto comercial de ciertos aspectos tecnológicos. Cinavia es una marca comercial de Verance Corporation. Copyright 2004-2013 Verance Corporation. Todos los derechos reservados por Verance. La ingeniería inversa o desensamblaje están prohibidos. Limitación de responsabilidad de servicios de red Todo el contenido y servicios accesibles a través del dispositivo pertenecen a otros fabricantes y están protegidos mediante copyright, patente, marca comercial y otras leyes de propiedad intelectual. Dicho contenido y servicios únicamente se facilitan para uso personal no comercial. No puede utilizar el contenido o servicios para un fin no autorizado por el propietario del contenido o por el proveedor de servicios. Sin limitación de lo siguiente, a menos que sea expresamente autorizado por el propietario del contenido en cuestión o por el proveedor de servicios, no puede modificar, copiar, volver a publicar, cargar, enviar, transmitir, convertir, enviar, crear trabajos derivados, explotar ni distribuir de manera alguna ni en medio alguno ningún contenido o servicios que se muestren a través de este dispositivo. EL CONTENIDO Y SERVICIOS DE OTROS FABRICANTES SE FACILITA “TAL CUAL”. SAMSUNG NO GARANTIZA EL CONTENIDO NI LOS SERVICIOS FACILITADOS, DE FORMA EXPRESA O IMPLÍCITA, PARA CUALQUIER FIN. SAMSUNG RECHAZA EXPRESAMENTE CUALQUIER GARANTÍA IMPLÍCITA, INCLUIDA PERO NO LIMITADA A, GARANTÍAS DE COMERCIALIZACIÓN O IDONEIDAD PARA UN FIN CONCRETO. SAMSUNG NO GARANTIZA LA PRECISIÓN, LA VALIDEZ, LO OPORTUNO, LA LEGALIDAD O LO COMPLETO DE NINGÚN CONTENIDO O SERVICIO DISPONIBLE A TRAVÉS DEL DISPOSITIVO Y BAJO NINGUNA CIRCUNSTANCIA, INCLUIDA NEGLIGENCIA, SAMSUNG SERÁ RESPONSABLE, YA SEAPOR CONTRATO O BAJO RESPONSABILIDAD EXTRACONTRACTUAL, DE NINGÚN DAÑO DIRECTO, INDIRECTO, INCIDENTAL, ESPECIAL O RESULTANTE, DE GASTOS JUDICIALES, OTROS GASTOS NI DE NINGÚN DAÑO COMO RESULTADO O RELACIONADO CON, CUALQUIER INFORMACIÓN CONTENIDA EN EL PRESENTE DOCUMENTO, O COMO RESULTADO DEL USO DE CUALQUIER CONTENIDO O SERVICIO POR PARTE DE USTED O DE UN TERCERO, INCLUSO AUNQUE SE INFORME DE LA POSIBILIDAD DE TALES DAÑOS. Los servicios de terceros pueden terminarse o interrumpirse en cualquier momentoy y Samsung no se hace responsable ni garantiza que ningún contenido o servicio permanecerá disponible durante un período de tiempo. El contenido y los servicios lo transmiten terceros mediante las redes y las instalaciones de transmisión sobre las que Samsung no tiene ningún control Si limitarse a las generalidades de la cláusula de exención de responsabilidad, Samsung rechaza expresamente cualquier responsabilidad por la interrupción o suspensión de cualquier contenido o servicio disponible a través de este dispositivo. Samsung no es responsable del servicio al cliente relacionado con los contenidos y el servicio. Cualquier pregunta o solicitud sobre el servicio relacionado con contenidos o servicios debe enviarse directamente a los proveedores de los contenidos y servicios correspondientes.. Licencia • Fabricado con licencia de Dolby Laboratories. Dolby y el símbolo de la doble D marcas comerciales de Dolby Laboratories. • Para patentes de DTS, consulte http://patents.dts.com. Fabricado con licencia de DTS Licensing Limited. DTS, el símbolo, y DTS y el símbolo juntos son marcas comerciales registradas y DTS 2.0+Digital Out es una marca comercial de DTS, Inc. © DTS, Inc. Todos los derechos reservados. 2.0+Digital Out • DivX -- INFORMACIÓN SOBRE VIDEO DIVX: DivX® es un formato de vídeo digital creado por DivX, LLC, una filial de Rovi Corporation. Este aparato es un dispositivo oficial DivX Certified® que ha pasado pruebas rigurosas para verificar que reproduce vídeo DivX. Visite divx.com para obtener más información y herramientas de software para convertir sus archivos en vídeos DivX. -- INFORMACIÓN SOBRE DIVX VIDEO-ON-DEMAND: Este dispositivo DivX Certified® debe registrarse para poder reproducir películas DivX Video-on-Demand (VOD) compradas. Para obtener el código de registro, localice la sección DivX VOD en el menú de configuración del dispositivo. Vaya a vod.divx.com para obtener información adicional sobre la forma de completar el registro. -- DivX Certified® reproduce vídeo DivX® hasta HD 1080p, incluido contenido premium. DivX®, DivX Certified® y los logotipos asociados son marcas comerciales de Rovi Corporation o sus filiales y se utilizan con licencia. Este producto está cubierto por una de las siguientes patentes de EE.UU.: 7,295,673; 7,460,668; 7,515,710; 7,519,274. • HDMI, el logotipo de HDMI y High-Definition Multimedia Interface son marcas comerciales o marcas registradas de HDMI Licensing LLC en Estados Unidos y en otros países. • Oracle y Java son marcas registradas de Oracle y sus filiales. Otros nombres pueden ser marcas comerciales de sus respectivos propietarios. • Aviso sobre licencia de código abierto -- En caso de que se utilice software de código abierto, las licencias de código abierto están disponibles en el menú del producto. • Blu-ray Disc™, Blu-ray™ y los logotipos son marcas comerciales de Blu-ray Disc Association. 25 SOLO MÉXICO IMPORTADO POR : SAMSUNG ELECTRONICS MÉXICO S.A. DE C.V GENERAL MARIANO ESCOBEDO 476 PISO 8 COL. ANZURES, DELEGACIÓN MIGUEL HIDALGO MÉXICO DISTRITO FEDERAL C.P. 11590 TEL : 01 (55) 5747-5100 / 01 800 726 7864 Comuníquese con SAMSUNG WORLD WIDE Si desea formular alguna pregunta o comentario en relación con los productos de Samsung, comuníquese con el centro de atención al cliente de SAMSUNG Country ` North America CANADA Contact Center 1-800-SAMSUNG (726-7864) U.S.A MEXICO 1-800-SAMSUNG (726-7864) 01-800-SAMSUNG (726-7864) ARGENTINE URUGUAY PARAGUAY 0800-333-3733 000 405 437 33 009 800 542 0001 0800-124-421 (Demais cidades e regiões) 4004-0000 (Capitais e grandes centros) 800-SAMSUNG(726-7864) 800-10-7260 01 8000 112 112 Bogotá 600 12 72 ` Latin America BRAZIL CHILE BOLIVIA COLOMBIA COSTA RICA DOMINICA 0-800-507-7267 1-800-751-2676 Web Site Country Contact Center ECUADOR 1-800-10-7267 EL SALVADOR 800-6225 GUATEMALA 1-800-299-0013 www.samsung.com.ar www.samsung.com www.samsung.com.py HONDURAS 800-27919267 NICARAGUA 001-800-5077267 www.samsung.com/cl www.samsung.com PANAMA www.samsung.com/ca (English) www.samsung.com/ca_fr (French) www.samsung.com/us www.samsung.com www.samsung.com.br www.samsung.com/co www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) JAMAICA PERU PUERTO RICO TRINIDAD & TOBAGO VENEZUELA 1-800-234-7267 800-7267 0-800-777-08 1-800-682-3180 1-800-SAMSUNG(726-7864) 0-800-100-5303 Web Site www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/latin (Spanish) www.samsung.com/latin_en (English) www.samsung.com/pe www.samsung.com www.samsung.com www.samsung.com/ve AK68-02419A-00 AK68-02419A-00
This document in other languages
- español: Samsung BD-H5900