Download Samsung 172T Hướng dẫn sử dụng
Transcript
SyncMaster 152T/172T/192T http://www.samsung-monitor.com http://www.samsungusa.com/monitor BN68-00150M-00 Contents English Safety Instructions 2 Unpacking Your Monitor 3 Setting up Your Monitor 4 Connecting Your Monitor 4 Self-Test Feature Check 6 Warning Messages 7 Environment 7 Useful Tips 7 Adjusting Your Monitor User Controls 8 Menu Brightness 9 Contrast 9 Image Lock Fine 10 Coarse 10 H-Position 11 V-Position 11 Reset Geometry Reset 12 Color Reset 12 Color Temperature 12 Halftone 13 Language 13 Menu Position H-Position 14 V-Position 14 Menu Display Time 15 Display Mode 15 Source Select 15 Auto Adjustment 16 OSD Lock/Unlock 16 MagicBright 16 Power Saver 17 Troubleshooting 18 Specifications 20 Display Modes 23 Safety Instructions 1. Do not use a damaged or loose plug. 2. Do not pull the plug out by the wire nor touch the plug with wet hands. 3. Use only a properly grounded plug and receptacle. 4. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. 5. Do not connect too many extension cords or plugs to an outlet. 6. Put your monitor in a location with low humidity and a minimum of dust. 7. Do not drop the monitor when moving it. 8. Place the monitor on a flat and stable surface. 9. Set down the monitor carefully. 10. Do not place the monitor face down. 11. Installing a wall bracket must be done by a qualified professional. 12. Do not spray water or detergent directly on the monitor. 13. Use the recommended detergent with a smooth cloth. 14. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. 15. Do not remove cover(or back). No user serviceable parts inside. 16. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. 17. Be careful not to let water drip into the monitor or expose the monitor to moisture. 18. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. 19. Keep the power off when there is thunder and lightening outside, or let the monitor remain unused for an extended period of time. 20. Do not try to move the monitor by pulling on the wire or the signal cable. 21. Do not move the monitor right or left by pulling only the wire or the signal cable. 22. Do not cover the vents on the monitor cabinet. 23. Do not place water containers, chemical products or small metal objects on the monitor. 24. Do not use or store inflammable substances near the monitor. 25. Never insert anything metallic into the monitor openings. 26. Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. 27. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. 28. Be careful when adjusting the stand angle. 29. Adjust the resolution and frequency to the levels appropriate for the model. 30. Keep all power adaptors apart. 31. Keep power adaptor away from any other heat source. 32. Remove and discard vinyl bag from power adaptor before use. 33. Always keep power adaptor in well-ventilated area. 34. Keep the volume at a proper level when you use the headphones. 35. Keep a proper distance between your eyes and the monitor screen. 2 Unpacking Your Monitor Monitor and Stand Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. 152T/172T Auto Exit 192T Menu Source DC-Adapter Power Cord DVI Cable(Option) VESA Mounting Bracket D-Sub Cable User Manual For Multimedia model (Option) Sound Cables Multimedia Speaker Stand 3 Setting up Your Monitor Connecting Your Monitor Rear of Monitor Rear of Computer New Model Macintosh Old Model Macintosh 1. Connect the DC Adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analogue) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. 3. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete. 4 Setting up Your Monitor Connecting Your Monitor Setup-For Multimedia model 1. PC sound connection terminal (Input) 2. Headphone connection terminal (Output) 3. Volume 4. To listen in privacy, connect headphones here. 5. Connect a sound cable from the input source (sound card, computer, CD-ROM drive). 5 Setting up Your Monitor Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box with a border and text inside as shown in the following illustration: The three boxes inside the border are red, green and blue. Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. 6 Setting up Your Monitor Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or an “Video mode not supported” message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. 7 Adjusting Your Monitor User Controls 152T/172T 1 2 3 4 3 4 192T 1 2 1. Auto button: Use this button to auto adjustment direct access. 2. Exit button: Use this button to Exit the active menu or the OSD. Source button: When push the 'Source' button, then Selects the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -- analog or digital input signal.) 3. Adjust buttons: These buttons allow you to highlight and adjust items in the menu. MagicBright button(192T Only): MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. 4. Menu button: Use this button to open the OSD and activate a highlighted menu item. 8 Adjusting Your Monitor Brightness Adjust the Brightness. 1. Push the Menu ( ) button. 2. Push the Menu ( ) button to open the Brightness adjustment screen. 3. Use the + button to increase the brightness or - button to decrease the brightness. Direct Access Feature : When OSD is not on the screen, Push the + or - button to adjust brightness. Contrast Adjust the Contrast. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Contrast screen is displayed. 3. Push the Menu ( ) button to open the Contrast adjustment screen. 4. Use the + button to increase the contrast or - button to decrease the contrast. Note: Not Available This function doesn't work in Digital input. 9 Adjusting Your Monitor Image Lock Fine Image Lock is used to fine tune and get the best image by removing noises that creates unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Image Lock screen is displayed. 3. Push the Menu ( ) button twice to open the Fine adjustment screen. 4. Use the - or + buttons to remove any noise. Note: Not Available This function doesn't work in Digital input. Coarse Image Lock is used to fine tune and get the best image by removing noises that creates unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Image Lock screen is displayed. 3. Push the Menu ( ) button again and then press the - or + button until the Coarse screen appears. Push the Menu ( ) button to open the Coarse adjustment screen. 4. Use the - or + buttons to remove any noise. Note: Not Available This function doesn't work in Digital input. 10 Adjusting Your Monitor H-Position Follow these instructions to change the horizontal position of the monitor's entire display. 1. Push the Menu ( ) button. 2. Push the - button or + button until the H-Position screen is displayed. 3. Push the Menu ( ) button to open the H-Position adjustment screen. 4. Use the - and + buttons to change the horizontal position of the monitor's viewing area. Note: Not Available This function doesn't work in Digital input. V-Position Follow these instructions to change the vetical position of the monitor's entire display. 1. Push the Menu ( ) button. 2. Push the - button or + button until the V-Position screen is displayed. 3. Push the Menu ( ) button to open the V-Position adjustment screen. 4. Use the - and + buttons to change the vertical position of the monitor's viewing area. Note: Not Available This function doesn't work in Digital input. 11 Adjusting Your Monitor Reset Geometry Reset Geometry parameters are replaced with the factory default values. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Reset screen is displayed. 3. Push the Menu ( ) button twice to open the Geometry Reset adjustment screen. 4. Push the + button to select Yes. If you don't want to reset the monitor, use the - button to select No. Note: Not Available This function doesn't work in Digital input. Color Reset Color parameters are replaced with the factory default values. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Reset screen is displayed. 3. Push the Menu ( ) button again and then press the - or + button until the Color Reset screen appears. Push the Menu ( ) button to open the Color Reset adjustment screen. 4. Push the + button to select Yes. If you don't want to reset the monitor, use the - button to select No. Color Temperature (152T/172T) Color temperature is a measure of the "warmth"of the image colors. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Color Temperature screen is displayed. 3. Push the Menu ( ) button to open the Color Temperature adjustment screen. 4. Press the - or + button to select User Adjusted, Reddish, Bluish or sRGB (When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits.) Note: Not Available This function doesn't work in Digital input. 12 Adjusting Your Monitor Color Temperature (192T) Color temperature is a measure of the "warmth"of the image colors. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Color Temperature screen is displayed. 3. Push the Menu ( ) button to open the Color Temperature adjustment screen. 4. Press the - or + button to select User Adjusted, Reddish, Bluish. Note: Not Available This function doesn't work in Digital input. But sRGB mode works in Digital input. Halftone Change the opaqueness of the background of the OSD. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Halftone screen is displayed. 3. Push the Menu ( screen. ) button to open the Halftone selection 4. Use the - button or + button to select On or Off. Language Follow these steps to change the language used in the menu. You can choose one of ten languages. (English, German, Spanish, French, Italian, Swedish, Russian, Chinese, Japanese, Korean) Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Languages screen is displayed. 3. Push the Menu ( selection screen. ) button to open the languages 4. Use the - button or + button to select the language you would like to use. 13 Adjusting Your Monitor Menu Position H-Position You can change the horizontal position where the OSD menu appears on your monitor. 1. Push the Menu ( ) button. 2. Push the - button or + button until the H-Menu Position screen is displayed. 3. Push the Menu ( ) button twice to open the H-Position adjustment screen. 4. Use the - and + buttons to place the menu in the horizontal position you prefer. V-Position You can change the vertical position where the OSD menu appears on your monitor. 1. Push the Menu ( ) button. 2. Push the - button or + button until the V-Menu Position screen is displayed. 3. Push the Menu ( ) button again and then press the - or + button until the V-Position screen appears. Push the Menu ( ) button to open the V-Position adjustment screen. 4. Use the - and + buttons to place the menu in the vertical position you prefer. 14 Adjusting Your Monitor Menu Display Time The menu will automatically turn off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it turns off. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Menu Display Time screen is displayed. 3. Push the Menu ( ) button to open the Menu Display Time adjustment screen. 4. Use the - or + buttons to select 5, 10, 20, 50, 200 seconds. 20 seconds is the default value. Display Mode (152T/172T) You can see the frequency, the polarity of the operational signals and the resolution level. Note These screens do not allow any changes to the settings, they are for information only. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Display Mode screen is displayed. Source Select (192T) You can see the frequency, the polarity of the operational signals and the resolution level. Select Auto Source Select for the monitor to automatically select the signal sorce. Select Manual Source Select to manually select the signal source using the Source button. When push the 'Source' button, then Selects the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -analog or digital input signal.) Note If you select the Digital mode, you must connect your monitor to the graphic card with a digital port using the DVI cable. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Source Select screen is displayed. 15 Adjusting Your Monitor Auto Adjustment Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. 1. Push the Auto button. To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. Note: Not Available This function doesn't work in Digital input. OSD Lock/Unlock 1. Push and hold in the Menu ( or more to Lock the OSD. ) button for 5 seconds 2. Push and hold in the Menu ( or more to Unlock the OSD. ) button for 5 seconds MagicBright (192T) MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. Note Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust Brightness and Contrast by using OSD menu. Or push (+) button when OSD screen is not on to access Brightness control directly. 1. Push the MagicBright button. Then push the MagicBright button again to circle through available preconfigured modes. Text: Normal Brightness For documentations or works involving heavy text. Internet: Medium Brightness For working with mixture of contents such as text and graphics. Entertain: High Brightness For watching motion pictures such as DVD and VCD. 16 PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Normal Operation Power saving mode EPA/ENERGY 2000 Power Switch off 120Vac Power Indicator Green Green, Blinking Black Less than 2W Less than 1W Power Consumption 152T Less than 31W 172T Less than 42W 192T Less than 45W This monitor is EPA ENERGY STAR ® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR ® Partner, SAMSUNG has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency. 17 Troubleshooting Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Check List Symptom No images on the screen. I cannot turn on the monitor. Check List Is the power cord connected properly? Solution Check the power cord connection and supply. Can you see "No Connection, (Connected using the D-sub cable) Check Signal Cable" on the screen? Check the signal cable connection. (Connected using the DVI cable) If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analogue. Press Source button to have the monitor double-check the input signal source. If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/2000/XP) and then change the frequency of the video card. (Refer to the Preset Display Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer. Can you see "Video mode not supported" on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle. Adjust the maximum resolution and frequency that the monitor can properly handle. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Connected using the DVI cable? You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system. 18 Press a key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. Troubleshooting Check List Symptom I cannot see the On Screen Display. The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Check List Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly? Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor? Solution Unlock the OSD by pressing the MENU button for at least 5 seconds. Check the signal cable connection. Make sure the video card is fully inserted in it's slot. Reboot the computer. Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Display Modes). The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. Adjust the resolution and frequency of Have you adjusted the resolution the video card. or frequency on the monitor? (Refer to the Preset Display Modes). Is the frequency properly adjusted Adjust the frequency properly by when checking the Display Timing referring to the video card manual on the menu? and the Preset Display Modes. Have the Windows colors been set properly? Has the video card been set properly? There is a message that reads Have you installed the monitor "Unrecognized monitor, Plug & driver? Play (VESA DDC) monitor See the video card manual to see found". if the Plug & Play (VESA DDC) function can be supported. 19 (The maximum frequency per resolution may differ from product to product.) For Windows ME/2000/XP: Set the colors properly at the Control Panel, Display, Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions. Specifications General Model Name SyncMaster 152T LCD Panel Size 15.0 inch diagonal Display area 304.1 (H) x 228.1 (V) Pixel Pitch 0.297 (H) x 0.297 (V) Type a-si TFT active matrix Viewing Angle 160/130(H/V) Synchronization 30 ~ 61 kHz Horizontal 56 ~ 75 Hz Vertical Display Color 16,294,277 Colors Resolution Optimum resolution 1024 x 768@60Hz Maximum resolution 1024 x 768@75Hz Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB, Composite Sync, SOG(cable option), 0.7 Vp-p Positive at 75 ohms Separate H/V sync, TTL level positive or negative Maximum Pixel Clock 80 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable, DVI-D to DVI-D cable, Detachable Power Consumption Less Than 31W Dimensions (WxDxH) / Weight 357.5 X 184.5 X 361.6mm (After installing of Stand) / 2.9kg (With Bagic Stand) 357.5 X 50.7 X 288.5mm (After folding the stand) / 3.1kg (Multimedia Stand) VESA Mounting Interface 75mm x 75mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Operating Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 2,359,296. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note Design and specifications are subject to change without prior notice. 20 Specifications General Model Name SyncMaster 172T LCD Panel Size 17.0 inch diagonal Display area 337.92 (H) x 270.336 (V) Pixel Pitch 0.264 (H) x 0.264 (V) Type a-si TFT active matrix Viewing Angle 170/170(H/V) Synchronization 30 ~ 81 kHz Horizontal 56 ~ 75 Hz Vertical Display Color 16,294,277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@75Hz Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG(cable option), 0.7Vp-p Positive at 75 ohms Separate H/V sync, TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable, DVI-D to DVI-D cable, Detachable Power Consumption Less Than 42W Dimensions (WxDxH) / Weight 385 x 216 x 404.7 mm (After installing of Stand) / 4.7 kg (With Basic Stand) 385 x 56.8 x 324.7mm (After folding the stand) / 4.7 kg (Multimedia Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Operating Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note Design and specifications are subject to change without prior notice. 21 Specifications General Model Name SyncMaster 192T LCD Panel Size 19.0 inch diagonal Display area 376.32 (H) x 301.056 (V) Pixel Pitch 0.297 (H) x 0.297 (V) Type a-si TFT active matrix Viewing Angle 170/170(H/V) Synchronization 30 ~ 81 kHz Horizontal 56 ~ 75 Hz Vertical Display Color 16,194,277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@75Hz Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG, 0.7Vp-p Positive at 75 ohms Separate H/V sync, TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable, DVI-D to DVI-D cable, Detachable Power Consumption Less Than 45W Dimensions (WxDxH) / Weight 431 x 220 x 447 mm (After installing of Stand) / 5.5 kg (With Basic Stand) 431 x 29.7 x 324.7mm (After folding the stand) / 5.6 kg (Multimedia Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Operating Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note Design and specifications are subject to change without prior notice. 22 Display Modes IIf the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) SyncMaster 172T/192T MAC. 640 x 480 35.000 66.667 30.240 -/- MAC. 832 x 624 49.726 74.551 57.284 -/- IBM. 640 x 350 31.469 70.086 25.175 +/- IBM. 640 x 480 31.469 59.940 25.175 -/- IBM. 720 x 400 31.469 70.087 28.322 -/+ VESA. 640 x 480 37.500 75.000 31.500 -/- VESA. 640 x 480 37.861 72.809 31.500 -/- VESA. 800 x 600 35.156 56.250 36.000 +.-/+.- VESA. 800 x 600 37.879 60.317 40.000 +/+ VESA. 800 x 600 46.875 75.000 49.500 +/+ VESA. 800 x 600 48.077 72.188 50.000 +/+ VESA. 1024 x 768 48.363 60.004 65.000 -/- VESA. 1024 x 768 56.476 70.069 75.000 -/- VESA. 1024 x 768 60.023 75.029 78.750 +/+ SyncMaster 152T/172T/192T SyncMaster 172T/192T VESA. 1280 x 1024 63.981 60.020 108.00 +/+ VESA. 1280 x 1024 79.976 75.025 135.00 +/+ SUN. 1280 x 1024 81.129 76.106 135.00 -/- Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz 23 MEMO 152_172_192T-vet.qxd 8/25/2003 9:53 PM Page 1 Muïc Luïc Tieáng Vieät Höôùng Daãn An Toaøn 2 Maøn Hình Vi Tính 3 Caøi Ñaët Maøn Hình 4 Keát Noái Maøn Hình 4 Kieåm Tra Chöùc Naêng Töï Kieåm 6 Thoâng Ñieäp Caûnh Baùo 7 Moâi Tröôøng 7 Caùc Löu YÙ Khi Duøng 7 Chænh Maøn Hình Caùc Phím Ñieàu Chænh 8 Söû Duïng Maøn Hình Ñoä Saùng (Brightness) 9 Ñoä Töông Phaûn (Contrast) 9 Khoùa hình aûnh (Image Lock) Tinh chænh (Fine) 10 Chænh thoâ (Coarse) 10 Vò trí ngang (H-Position) 11 Vò trí doïc (V-Position) 11 Caøi ñaët laïi thoâng (Reset) Caøi ñaët laïi thoâng soá hình hoïc (Geometry Reset) 12 Caøi ñaët laïi thoâng soá maøu saéc (Color Reset) 12 Ñoä noùng maøu (Color Temperature) 12 Ñoä trung gian maøu (Halftone) 13 Ngoân Ngöõ (Language) 13 Vò trí Muïc luïc (Menu Position) Vò trí ngang (H-Position) 14 Vò trí doïc (V-Position) 14 Thôøi gian hieån thò muïc luïc (Menu Display Time) 15 Cheá ñoä hieån thò (Display Mode) 15 Source Select 15 Ñieàu chænh töï ñoäng (Auto Adjustment) 16 Khoùa/Môû Khoùa (OSD Lock/Unlock) 16 MagicBright 16 Tieát Kieäm Naêng Löôïng 17 Giaûi Quyeát Söï Coá 18 Ñaëc Tính Kyõ Thuaät 20 Cheá Ñoä Hieån Thò 23 152_172_192T-vet.qxd 8/25/2003 9:53 PM Page 2 Höôùng Daãn An Toaøn 1. Khoâng neân söû duïng phích caém bò hoûng hoaëc loûng. 2. Khoâng neân ruùt phích caém ra baèng caùch keùo daây ñieän cuõng nhö khoâng neân chaïm vaøo phích caém baèng tay öôùt. 3. Chæ neân duøng phích caém vaø oå ñieän ñöôïc noái ñaát ñuùng. 4. Khoâng neân laøm cong phích caém vaø daây ñieän cuõng nhö khoâng neân ñaët nhöõng vaät theå naëng leân chuùng, laøm chuùng hö hoûng. 5. Khoâng neân noái quaù nhieàu daây ñieän hoaëc phích caém vaøo moät oå caém. 6. Haõy ñaët maøn hình ôû nôi coù ñoä aåm khoâng cao vaø ít buïi nhaát. 7. Khoâng ñöôïc laøm rôùt maøn hình khi di chuyeån noù. 8. Haõy ñaët maøn hình treân moät beà maët phaúng vaø vöõng chaéc. 9. Ñaët maøn hình xuoáng moät caùch caån thaän. 10. Khoâng ñöïôc ñaët maøn hình uùp maët xuoáng. 11. Vieäc gaén giaù treo töôøng phaûi do moät chuyeân vieân kinh nghieäm thöïc hieän. 12. Khoâng ñöôïc xòt nöôùc hoaëc chaát taåy tröïc tieáp leân maøn hình. 13. Haõy duøng chaát taåy ñöôïc ñeàà nghò vôùi vaûi meàm. 14. Neáu choã keát noái giöõa phích caém vaø chaân caém bò baùm buïi hoaëc baån haõy lau chuøi ñuùng caùch baèng vaûi khoâ. 15. Khoâng ñöôïc thaùo voû maùy (hoaëc maët sau). Khoâng ñöôïc laép baát cöù linh kieän naøo khaùc vaøo beân trong. 16. Trong tröôøng hôïp maøn hình cuûa baïn hoaït ñoäng khoâng bình thöôøng, vaø ñaëc bieät laø maøn hình phaùt aâm thanh hoaëc toûa muøi laï - haõy laäp töùc thaùo daây caém ñieän vaø lieân heä vôùi moät ñaïi lyù hoaëc dòch vuï ñöôïc uûy quyeàn. 17. Haõy caån thaän ñöøng ñeå nöôùc vaáy leân maøn hình hoaëc ñeå maøn hình chòu hôi aåm. 18. Neáu maøn hình bò rôùt hoaëc voû maøn hình bò hö haïi, haõy taét maùy vaø ruùt phích caém ñieän ra. 19. Haõy taét maøn hình khi ngoaøi trôøi coù saám seùt, hoaëc khi khoâng söû duïng trong thôøi gian daøi. 20. Khoâng ñöôïc coá gaéng di chuyeån maøn hình baèng caùch keùo daây ñieän hoaëc daây caùp tín hieäu. 21. Khoâng ñöôïc di chuyeån maøn hình sang phaûi hoaëc traùi baèng caùch chæ keùo daây ñieän hoaëc daây caùp tín hieäu. 22. Khoâng ñöôïc che phuû loã thoâng hôi treân voû maøn hình. 23. Khoâng ñöôïc ñaët bình chöùa nöôùc, caùc saûn phaåm hoùa hoïc hoaëc nhöõng vaät nhoû baèng kim loaïi leân maøn hình. 24. Khoâng ñöôïc söû duïng hoaëc ñaët nhöõng chaát deã chaùy noå gaàn maøn hình. 25. Khoâng bao giôø ñöôïc gaén baát cöù vaät theå baèng kim loaïi naøo vaøo beân trong maøn hình. 26. Khoâng ñöôïc gaén nhöõng vaät kim loaïi nhö ñoà duøng nhaø beáp, daây daãn hoaëc muõi khoan; hay nhöõng vaät deã baét löûa nhö nhöõng maåu giaáy hoaëc dieâm queït vaøo loã thoâng hôi hoaëc coång headphone hoaëc coång A/V treân maøn hình. 27. Neáu baïn xem moät maøn hình coá ñònh trong thôøi gian daøi, hieän töôïng hình to ra hoaëc môø ñi coù theå xuaát hieän. 28. Haõy caån thaän khi ñieàu chænh giaù ñôõ cuûa maøn hình. 29. Ñieàu chænh ñoä phaân giaûi vaø taàn soá ôû möùc ñoä thích hôïp ñoái vôùi kieåu maùy. 30. Haõy ñeå nhöõng boä ñoåi ñieän caùch xa nhau. 31. Haõy ñeå boä ñoåi ñieän traùnh xa baát cöù nguoàn phaùt nhieät khaùc naøo. 32. Thaùo boû caùc boïc nhöïa khoûi boä ñoåi ñieän tröôùc khi söû duïng. 33. Luoân giöõ boä ñoåi ñieän ôû nôi thoâng thoaùng. 34. Haõy chænh aâm löôïng ôû möùc thích hôïp khi baïn söû duïng headphone. 35. Haõy giöõ moät khoaûng caùch thích hôïp giöõa maét vaø maøn hình. 2 152_172_192T-vet.qxd 8/25/2003 9:53 PM Page 3 Maøn Hình Vi Tính Maøn Hình vaø Chaân Ñeá Kieåm tra vaät tö döôùi ñaây coù ñöôïc keøm theo maøn hình hay khoâng. Neáu khoâng ñuû, lieân laïc vôùi ngöôøi baùn ñeå yeâu caàu nhaän ñuû. 152T/172T Auto Exit 192T Menu Source Boä chuyeån ñieän moät chieàu (DC-Adapter) Boä phaän treo töôøng VESA Caùp DVI (tuøy choïn) Daây nguoàn Caùp tín hieäu Saùch höôùng daãn caøi ñaët Daønh cho kieåu maùy Ña phöông tieän (Multimedia) (Tuøy choïn) Boä loa ñöùng Multimedia Caùp aâm thanh 3 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 4 Caøi Ñaët Maøn Hình X Keát Noái Maøn Hình Maët sau maøn hình Maët sau maùy tính Kieåu maùy Macintosh môùi Kieåu maùy Macintosh cuõ 1. Gaén boä bieán ñieän moät chieàu cho maøn hình cuûa baïn vaøo coång ñieän nguoàn ôû maët sau maøn hình. Caém daây nguoàn cuûa maøn hình vaøo oå caém ñieän gaàn nhaát. 2-1. Duøng boä noái D-Sub (Analog) treân theû video. Gaén caùp tín hieäu vaøo khe caém 15 chaân, D-sub naèm ôû maët sau cuûa maøn hình. 2-2. Duøng boä noái DVI (Digital) treân theû video. Keát noái caùp DVI vaøo ngoõ DVI ôû maët sau maøn hình. 3. Keát noái vôùi moät maùy tính Macintosh. Caém maøn hình vaøo maùy Macintosh baèng caùp D-SUB. 4. Trong tröôøng hôïp söû duïng maùy Macintosh kieåu cuõ, baïn caàn moät ñaàu noái ñaëc bieät daønh cho maùy MAC ñeå caém maøn hình vaøo maùy. 5. Baät maùy tính vaø maøn hình. Neáu maøn hình hieån thò hình aûnh, quaù trình laép ñaët thaønh coâng. 4 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 5 Caøi Ñaët Maøn Hình X Ketá Noiá Manø Hình Caøi ñaët daønh cho kieåu maùy Multimedia 1. Khe caém aâm thanh PC (Ñaàu vaøo - Input) 2. Khe caém headphone (Ñaàu ra - Output) 3. AÂm löôïng 4. Ñeå nghe moät mình, caém headphone vaøo ñaây. 5. Caém moät caùp aâm thanh töø nguoàn phaùt (card aâm thanh, maùy tính, oå ñóa CD-ROM). 5 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 6 Caøi Ñaët Maøn Hình X Kieåm tra chöùc naêng töï kieåm: Maùy tính cuûa baïn coù chöùc naêng töï kieåm tra, baïn coù theå kieåm tra chöùc naêng naøy baèng caùch: 1. Taét maùy tính vaø maøn hình cuûa baïn. 2. Ruùt daây tín hieäu ra khoûi maùy. 3. Baät nguoàn cho maøn hình. Neáu maøn hình hoaït ñoäng bình thöôøng, baïn seõ thaáy moät hoäp coù khung vieàn vaø doøng chöõ beân trong nhö hình minh hoïa sau: Ba hoäp naèm trong khung vieàn laø ñoû, xanh laù vaø xanh lam. 4. Taét nguoàn maøn hình vaø keát noái daây tín hieäu, sau ñoù baät caû maøn hình vaø maùy tính. Neáu maøn hình vaãn maøu ñen khi ñaõ thöïc hieän caùc böôùc tröôùc ñoù, kieåm tra card maøn hình vaø heä thoáng maùy tính. 6 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 7 Caøi Ñaët Maøn Hình Thoâng ñieäp caûnh baùo Neáu tín hieäu vaøo khoâng töông thích, moät thoâng ñieäp seõ xuaát hieän treân maøn hình hoaëc maøn hình seõ ñen maëc duø ñeøn chæ thò vaãn saùng. Thoâng ñieäp chæ ra raèng tín hieäu vöôït qua möùc cho pheùp maøn hình hoaëc baïn neân kieåm tra daây caùp tín hieäu. Moâi tröôøng Vò trí vaø höôùng laép ñaët coù aûnh höôûng ñeán chaát löôïng cuûa maøn hình. 1. Khoâng neân ñeå loa traàm gaàn maøn hình maø neân di chuyeån loa traàm sang phoøng khaùc. 2. Baïn neân di chuyeån caùc thieát bò ñieän( quaït ñieän, ñieän thoaïi ...) caùch xa maøn hình khoaûng hôn 1 meùt. 3. Baïn neân khöû töø khi di chuyeån maøn hình sang höôùng khaùc. Caùc löu yù khi duøng. Maøn hình taïo ra caùc tín hieäu coù theå thaáy ñöôïc, nhaän ñöôïc töø maùy tính. Do ñoù, maùy tính coù vaán ñeà hoaëc card maøn hình coù vaán ñeà, maøn hình seõ chuyeån sang maøu ñen hoaëc maøu khoâng chuaån, maøn hình bò oàn, vöôït möùc tín hieu Trong tröôøng hôïp naøy, tröôùc tieân kieåm tra caùc tín hieäu hoaëc goïi cho traïm baûo haønh neáu baïn khoâng giaûi quyeát ñöôïc. Caùc vaán ñeà trong quaù trình hoaït ñoäng cuûa maøn hình. Neáu khoâng coù hình aûnh hoaëc coù doøng kyù töï “ Video mode not supported” hieån thò treân maøn hình, thaùo daây tín hieäu khoûi maùy tính khi maøn hình vaãn ñeå nguoàn. °Neáu coù kyù töï hieån thò treân maøn hình hoaëc maøn hình chuyeån veà maøu traéng nghóa laø maøn hình vaãn hoaït ñoäng bình thöôøng. °Trong tröôøng hôïp naøy, kieåm tra maùy tính cuûa baïn. 7 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 8 Söû Duïng Maøn Hình X Caùc Phím Ñieàu Chænh 152T/172T 1 2 3 4 3 4 192T 1 2 1. Nuùt Auto: Duøng phím naøy ñeå truy caäp tröïc tieáp cheá ñoä ñieàu chænh töï ñoäng. 2. Nuùt Exit: Duøng thoaùt khoûi caùc muïc chænh hay maøn hình hieån thò. Nuùt Source: Khi baïn aán phím 'Source', maøn hình seõ choïn tín hieäu Video trong khi ñoù OSD taét. (Khi aán phím Source ñeå chuyeån ñoåi cheá ñoä ñaàu vaøo, moät thoâng ñieäp seõ hieån thò giöõa maøn hình ñeå thoâng baùo veà cheá ñoä hieän haønh -- tín hieäu vaøo ôû daïng kyõ thuaät soá (digital) hay daïng töông töï (analog)). 3. Caùc phím ñieàu chænh: Di chuyeån con troû tôùi muïc choïn vaø chænh giaù trò trong muïc choïn. Nuùt MagicBright (chæ coù ôû 192T): MagicBright laø moät chöùc naêng môùi, taïo moâi tröôøng thöôûng ngoaïn toái öu theå theo noäi dung hình aûnh baïn ñang xem. Hieän ñang coù saün ba cheá ñoä khaùc nhau: Text, Internet, vaø Entertain. Moãi cheá ñoä coù trò soá ñoä saùng rieâng ñöôïc caáu hình saün. Baïn coù theå deã daøng choïn moät trong ba caùch thieát laäp khi chæ caàn nhaán caùc nuùt ñieàu khieån MagicBright. 4. Nuùt MENU: Söû duïng môû maøn hình OSD hoaëc kích hoaït caùc muïc ñöôïc choïn. 8 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 9 Söû Duïng Maøn Hình Ñoä Saùng (Brightness) Duøng hieäu chænh ñoä saùng cuûa maøn hình hieån thò. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím Muïc Luïc ( ) ñeå môû maøn hình ñieàu chænh Brightness (Ñoä saùng). 3. Duøng phím + ñeå taêng ñoä saùng hoaëc phím - ñeå giaûm ñoä saùng. Tính naêng truy caäp tröïc tieáp: Khi OSD khoâng hieån thò treân maøn hình, nhaán phím + hoaëc - ñeå ñieàu chænh ñoä saùng. Ñoä Töông Phaûn (Contrast) Duøng hieäu chænh ñoä töông phaûn cuûa maøn hình hieån thò. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Contrast (Ñoä töông phaûn) hieån thò. 3. Nhaán phím Muïc Luïc ( ) ñeå môû maøn hình ñieàu chænh Contrast (Ñoä töông phaûn). 4. Duøng phím + ñeå taêng ñoä töông phaûn hoaëc phím - ñeå giaûm ñoä töông phaûn. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. 9 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 10 Söû Duïng Maøn Hình Khoùa hình aûnh (Image Lock) Tinh chænh (Fine) Chöùc naêng Image Lock duøng ñeå tinh chænh hình aûnh ñeå ñaït chaát löôïng hình toát nhaát baèng caùch loaïi boû caùc tín hieäu nhieãu laøm hình aûnh khoâng oån ñònh vì coù caùc veát môø vaø raêng cöa. Neáu chöa ñaït ñöôïc keát quaû nhö yù baèng chöùc naêng Fine (Tinh chænh), haõy duøng chöùc naêng Coarse (Chænh thoâ), sau ñoù duøng laïi chöùc naêng Fine. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Image Lock (Khoùa hình aûnh) hieån thò. 3. Nhaán phím Muïc Luïc ( chænh Fine. ) hai laàn ñeå môû maøn hình ñieàu 4. Duøng phím - hoaëc + ñeå loaïi boû nhieãu. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. Chænh thoâ (Coarse) Chöùc naêng Image Lock duøng ñeå tinh chænh hình aûnh ñeå ñaït chaát löôïng hình toát nhaát baèng caùch loaïi boû caùc tín hieäu nhieãu laøm hình aûnh khoâng oån ñònh vì coù caùc veát môø vaø raêng cöa. Neáu chöa ñaït ñöôïc keát quaû nhö yù baèng chöùc naêng Fine (Tinh chænh), haõy duøng chöùc naêng Coarse (Chænh thoâ), sau ñoù duøng laïi chöùc naêng coarse. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Image Lock (Khoùa hình aûnh) hieån thò. 3. Nhaán phím Muïc Luïc ( ) laàn nöõa, sau ñoù nhaán phím - hoaëc + ñeán khi maøn hình Coarse hieån thò. Nhaán phím Muïc Luïc ( ) ñeå môû maøn hình ñieàu chænh Coarse. 4. Duøng phím - hoaëc + ñeå loaïi boû nhieãu. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. 10 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 11 Söû Duïng Maøn Hình Vò trí ngang (H-Position) Haõy thöïc hieän theo nhöõng höôùng daãn naøy ñeå thay ñoåi vò trí ngang cuûa toaøn boä maøn hình hieån thò. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình H-Position (Vò trí ngang) hieån thò. 3. Nhaán phím Muïc Luïc ( H-Position. ) ñeå môû maøn hình ñieàu chænh 4. Duøng phím - hoaëc + ñeå thay ñoåi vò trí ngang cuûa toaøn boä maøn hình hieån thò. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. Vò trí doïc (V-Position) Haõy thöïc hieän theo nhöõng höôùng daãn naøy ñeå thay ñoåi vò trí doïc cuûa toaøn boä maøn hình hieån thò. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình V-Position (Vò trí doïc) hieån thò. 3. Nhaán phím Muïc Luïc ( V-Position. ) ñeå môû maøn hình ñieàu chænh 4. Duøng phím - hoaëc + ñeå thay ñoåi vò trí doïc cuûa toaøn boä maøn hình hieån thò. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. 11 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 12 Söû Duïng Maøn Hình Caøi ñaët laïi thoâng (Reset) Caøi ñaët laïi thoâng soá hình hoïc (Geometry Reset) Caùc thoâng soá hình hoïc ñöôïc thay baèng caùc giaù trò maëc ñònh khi saûn xuaát. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Reset (Caøi ñaët laïi thoâng) hieån thò. 3. Nhaán phím Muïc Luïc ( chænh Geometry Reset. ) hai laàn ñeå môûû maøn hình ñieàu 4. Nhaán phím + ñeå choïn Yes. Neáu baïn khoâng muoán caøi ñaët laïi maøn hình, haõy duøng phím - ñeå choïn No. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. Caøi ñaët laïi thoâng soá maøu saéc (Color Reset) Caùc thoâng soá maøu saéc ñöôïc thay baèng caùc giaù trò maëc ñònh khi saûn xuaát. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Reset (Caøi ñaët laïi thoâng) hieån thò. 3. Nhaán phím Muïc Luïc ( ) laàn nöõa roài nhaán phím - hoaëc + ñeán khi maøn hình Color Reset hieån thò. Nhaán phím Muïc Luïc ( ) ñeå môû maøn hình ñieàu chænh Color Reset. 4. Nhaán phím + ñeå choïn Yes. Neáu baïn khoâng muoán caøi ñaët laïi maøn hình, haõy duøng phím - ñeå choïn No. Ñoä noùng maøu (Color Temperature) (152T/172T) Nhieät ñoä maøu laø moät chöùc naêng ño ñoä "aám" cuûa maøu saéc hình aûnh. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Color Temperature (Ñoä noùng maøu) hieån thò. 3. Nhaán phím Muïc Luïc ( Color Temperature. ) ñeå môû maøn hình ñieàu chænh 4. Nhaán phím - hoaëc + ñeå choïn caùc muïc User Adjusted (Ngöôøi söû duïng ñieàu chænh), Reddish (Hôi ñoû), hoaëc Bluish (Hôi xanh). Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. 12 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 13 Söû Duïng Maøn Hình Ñoä noùng maøu (Color Temperature) (192T) Nhieät ñoä maøu laø moät chöùc naêng ño ñoä "aám" cuûa maøu saéc hình aûnh. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Color Temperature (Ñoä noùng maøu) hieån thò. 3. Nhaán phím Muïc Luïc ( Color Temperature. ) ñeå môû maøn hình ñieàu chænh 4. Nhaán phím - hoaëc + ñeå choïn caùc muïc User Adjusted (Ngöôøi söû duïng ñieàu chænh), Reddish (Hôi ñoû), hoaëc Bluish (Hôi xanh). Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. Ñoä trung gian maøu (Halftone) Thay ñoåi ñoä môø ñuïc cuûa hình neàn OSD. 1 AÁn phím Muïc Luïc ( ). 2 AÁn phím - hoaëc + tôùi khi maøn hình Menu hieån thò. 3 AÁn phím Muïc Luïc ( 4 Duøng nuùt - hoaëc + ñeå choïn baät hoaëc taét. ) ñeå vaøo maøn hình Halftone. Ngoân Ngöõ (Language) Baïn coù theå choïn moät trong möôøi ngoân ngöõ hieån thò coù trong maùy. (English, German, Spanish, French, Italian, Swedish, Russian, Chinese, Japanese, Korean) Ghi chuù Ngoân ngöõ ñöôïc choïn chæ aûnh höôûng treân maøn hình hieån thò, khoâng aûnh höôûng tôùi ngoân ngöõ hieån thò trong caùc phaàn meàm baïn söû duïng. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Language (Ngoân Ngöõ) hieån thò. 3. Nhaán phím Muïc Luïc ( Language. ) ñeå môû maøn hình ñieàu chænh 4. AÁn phím - hoaëc + ñeå choïn ngoân ngöõ muoán hieån thò. 13 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 14 Söû Duïng Maøn Hình Vò trí Muïc luïc (Menu Position) Vò trí ngang (H-Position) Baïn coù theå thay ñoåi vò trí ngang cuûa nôi xuaát hieän muïc luïc OSD treân maøn hình. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình H-Menu Position (Vò trí Muïc luïc) hieån thò. 3. Nhaán phím Muïc Luïc ( chænh H-Position. ) hai laàn ñeå môû maøn hình ñieàu 4. Duøng phím - hoaëc + ñeå ñaët muïc luïc vaøo vò trí ngang maø baïn thích. Vò trí doïc (V-Position) Baïn coù theå thay ñoåi vò trí doïc cuûa nôi xuaát hieän muïc luïc OSD treân maøn hình. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình V-Menu Position (Vò trí Muïc doïc) hieån thò. 3. Nhaán phím Muïc Luïc ( ) laàn nöõa roài nhaán phím - hoaëc + ñeán khi maøn hình V-Position (Vò trí doïc) hieån thò. Nhaán phím Muïc Luïc ( ) ñeå môû maøn hình ñieàu chænh V-Position. 4. Duøng phím - hoaëc + ñeå ñaët muïc luïc vaøo vò trí doïc maø baïn thích. 14 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 15 Söû Duïng Maøn Hình Thôøi gian hieån thò muïc luïc (Menu Display Time) Muïïc luïc seõ töï ñoäng taét neáu khoâng thöïc hieän ñieàu chænh naøo trong moät khoaûng thôøi gian nhaát ñònh. Baïn coù theå caøi ñaët thôøi gian chôø cuûa muïc luïc tröôùc khi töï ñoäng taét. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Menu Display Time (Thôøi gian hieån thò muïc luïc) hieån thò. 3. Nhaán phím Muïc Luïc ( ) ñeå môû maøn hình ñieàu chænh Menu Display Time. 4. Duøng phím - hoaëc + ñeå choïn caùc giaù trò 5, 10, 20, 50, 200 giaây. Giaù trò maëc ñònh laø 20 giaây. Cheá ñoä hieån thò (Display Mode) (152T/172T) Baïn coù theå thaáy giaù trò taàn soá, söï khaùc bieät cuûa caùc tín hieäu hoaït ñoäng vaø caáp ñoä phaân giaûi. Ghi chuù Caùc thoâng tin treân maøn hình khoâng theå thay ñoåi, chuùng chæ mang tính chaát caùc thoâng tin tham khaûo. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + ñeán khi maøn hình Display Mode hieån thò. Source Select (192T) Baïn coù theå thaáy giaù trò taàn soá, söï khaùc bieät cuûa caùc tín hieäu hoaït ñoäng vaø caáp ñoä phaân giaûi. Choïn Auto Source Select ñeå cho maøn hình töï ñoäng choïn nguoàn tín hieäu. Choïn Manual Source Select ñeå baïn töï choïn nguoàn tín hieäu baèng caùch duøng nuùt Source. Khi baïn aán phím 'Source', maøn hình seõ choïn tín hieäu Video trong khi ñoù OSD taét. (Khi aán phím Source ñeå chuyeån ñoåi cheá ñoä ñaàu vaøo, moät thoâng ñieäp seõ hieån thò giöõa maøn hình ñeå thoâng baùo veà cheá ñoä hieän haønh -- tín hieäu vaøo ôû daïng kyõ thuaät soá (digital) hay daïng töông töï (analog)). Ghi chuù Neáu choïn cheá ñoä Digital, baïn phaûi keát noái maøn hình vôùi card ñoà hoïa baèng caùch duøng caùp DVI qua coång digital. 1. AÁn phím Muïc Luïc ( ). 2. Nhaán phím - hoaëc + cho ñeán khi maøn hình Source Select hieån thò. 15 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 16 Söû Duïng Maøn Hình Ñieàu chænh töï ñoäng (Auto Adjustment) Chöùc naêng Auto Adjustment cho pheùp maøn hình coù theå töï ñieàu chænh theo tín hieäu video nhaän ñöôïc. Caùc giaù trò Fine, Coarse vaø Position seõ ñöôïc ñieàu chænh töï ñoäng. 1. Nhaán phím Auto. Ñeå cho chöùc naêng ñieàu chænh töï ñoäng chính xaùc hôn, haõy kích hoaït chöùc naêng 'AUTO' trong khi AUTO PATTERN ñang hoaït ñoäng. Ghi chuù: Khoâng coù hieäu löïc. Chöùc naêng naøy khoâng hoaït ñoäng vôùi cheá ñoä ñaàu vaøo Digital. Khoùa/Môû Khoùa (OSD Lock/Unlock) 1. AÁn vaø giöõ phím Muïc Luïc ( ) trong khoaûng hôn 5 giaây ñeå khoùa maøn hình hieån thò. 2. AÁn vaø giöõ phím Muïc Luïc ( ) trong khoaûng hôn 5 giaây ñeå môû khoùa maøn hình hieån thò. MagicBright (192T) MagicBright laø moät chöùc naêng môùi, taïo moâi tröôøng thöôûng ngoaïn toái öu theå theo noäi dung hình aûnh baïn ñang xem. Hieän ñang coù saün ba cheá ñoä khaùc nhau: Text, Internet, vaø Entertain. Moãi cheá ñoä coù trò soá ñoä saùng rieâng ñöôïc caáu hình saün. Baïn coù theå deã daøng choïn moät trong ba caùch thieát laäp khi chæ caàn nhaán caùc nuùt ñieàu khieån MagicBright. Ghi chuù Maëc duø caùc giaù trò ñaõ ñöôïc caùc kyõ sö choïn löïa caån thaän, nhöng caùc giaù trò ñöôïc caáu hình tröôùc naøy coù theå khoâng laøm baïn thoaûi maùi do khoâng hôïp thò hieáu cuûa baïn. Neáu vaäy, haõy chænh Brightness vaøContrast baèng vieäc söû duïng trình ñôn OSD. Hoaëc nhaán nuùt (+) khi khoâng coù maøn hình OSD ñeå thao taùc ñieàu chænh tröïc tieáp Ñoä saùng. 1. Nhaán nuùt MagicBright. Sau ñoù nhaán nuùt MagicBright laàn nöõa ñeå xem qua caùc cheá ñoä taïo caáu hình coù saün. Text: Ñoä saùng thöôøng Cho caùc taøi lieäu hay caùc coâng vieäc coù vaên baûn coù khoái löôïng lôùn. Internet: Ñoä saùng trung bình Ñeå laøm vieäc vôùi caùc noäi dung hoãn hôïp nhö vaên baûn vaø ñoà hoïa. Entertain: Ñoä saùng cao Ñeå xem caùc loaïi phim truyeän DVD vaø VCD. 16 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 17 Tieát Kieäm Naêng Löôïng Maøn hình Vi tính ñöôïc xaây döïng heä thoáng quaûn lyù naêng löôïng goïi laø möùc naêng löôïng thaáp. Cheá ñoä naøy seõ ñöa maùy veà cheá ñoä tieát kieäm naêng löôïng khi maùy khoâng duøng trong moät khoaûng thôøi gian. Khi baïn di chuyeån chuoät hay aán baát kyø phím naøo treân baøn phím, maøn hình seõ hoaït ñoäng laïi bình thöôøng. Baïn neân taét haún khi khoâng söû duïng trong moät thôøi gian daøi hoaëc khi vaéng nhaø. Cheá ñoä tieát kieäm naêng löôïng chæ hoaït ñoäng khi maùy tính cuûa baïn töông thích chuaån VESA DPMS. Tình traïng Bình thöôøng Cheá ñoä tieát kieäm naêng löôïng EPA/ENERGY 2000 Tieát kieäm naêng löôïng 120Vac Ñeøn chæ thò Xanh Ñeøn xanh nhaáp nhaùy Ñen Ít hôn 2 W Ít hôn 1 W Möùc tieâu thuï 152T Ít hôn 31 W 172T Ít hôn 42 W 192T Ít hôn 45 W 17 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 18 Giaûi Quyeát Söï Coá Tröôùc khi goïi ñieän ñeán dòch vuï hoã trôï, haõy ñoïc laïi thoâng tin trong phaàn naøy ñeå xem baïn coù theå töï khaéc phuïc ñöôïc söï coá naøo khoâng. Neáu baïn thaät söï caàn trôï giuùp, xin goïi soá ñieän thoaïi treân phieáu baûo haønh, soá ñieän thoaïi veà lónh vöïc thoâng tin hoaëc lieân heä vôùi ngöôøi baùn haøng. Danh saùch kieåm tra Trieäu chöùng Danh saùch kieåm tra Khoâng coù hình treân maøn hình. Daây ñieän nguoàn ñaõ ñöôïc gaén Toâi khoâng theå baät maøn hình leân. ñuùng caùch chöa? Caùc giaûi phaùp Kieåm tra vieäc noái daây ñieän vaø nguoàn ñieän. Baïn coù thaáy thoâng baùo “No Connection, Check Signal Cable” treân maøn hình khoâng?õ (Ñöôïc noái keát baèng caùp D-sub) Haõy kieåm tra vieäc noái caùp tín hieäu. (Ñöôïc noái keát baèng caùp DVI) Neáu baïn vaãn thaáy moät thoâng baùo (loãi) treân maøn hình khi maøn hình ñaõ ñöôïc noái keát ñuùng caùch, haõy kieåm tra tình traïng maøn hình xem coù ñaët ôû töông töï (analog) khoâng. Haõy nhaán nuùt Source ñeå maøn hình kieåm tra laïi nguoàn tín hieäu nhaäp. Neáu ñang coù ñieän nguoàn, haõy khôûi ñoäng laïi maùy tính ñeå xem maøn hình ban ñaàu (maøn hình khôûi nhaäp) nhö theá naøo. Neáu maøn hình ban ñaàu (maøn hình khôûi nhaäp) xuaát hieän, haõy khôûi ñoäng maùy tính ôû cheá ñoä öùng duïng (cheá ñoä safe mode ôû Windows ME/2000/XP) roài ñoåi taàn soá cuûa card hình aûnh. (Haõy tham khaûo Caùc cheá ñoä hieån thò ñaët tröôùc) Löu yù: Neáu maøn hình ban ñaàu (Maøn hình khôûi nhaäp) khoâng hieän ra, haõy lieân heä vôùi trung taâm baûo haønh hay ngöôøi baùn saûn phaåm. Baïn coù thaáy thoâng baùo “Video mode not supported” treân maøn hình khoâng? Baïn coù theå thaáy maåu tin naøy khi tín hieäu töø theû video vöôït quaù ñoä phaân giaûi vaø taàn soá toái ña maø maøn hình coù theå xöû lyù ñöôïc. Haõy ñieàu chænh ñoä phaân giaûi vaø taàn soá toái ña maø maøn hình coù theå xöû lyù ñöôïc. Khoâng coù hình aûnh treân maøn Maøn hình ñang ôû cheá ñoä Tieát kieäm hình. Coù phaûi ñeøn baùo ñieän nguoàn ñieän. treân maøn hình cöù nhaáp nhaùy sau Haõy nhaán moät phím treân baøn phím hay moãi giaây? di chuyeån chuoät ñeå kích hoaït maøn hình vaø phuïc hoài hình aûnh treân maøn hình. Keát noái baèng caùp DVI? 18 Baïn coù theå thaáy moät maøn hình traéng neáu baïn khôûi ñoäng heä thoáng tröôùc khi baïn noái caùp DVI; hay baïn ruùt caùp DVI vaø gaén laïi trong khi heä thoáng ñang chaïy vì coù moät soá loaïi card ñoà hoïa khoâng chuyeån tín hieäu video. Haõy noái caùp DVI vaø khôûi ñoäng laïi heä thoáng. 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 19 Giaûi Quyeát Söï Coá Danh saùch kieåm tra Trieäu chöùng Toâi khoâng thaáy menu On Screen Display. Maøn hình hieån thò caùc maøu laï hay chæ coù traéng ñen. Maøn hình baát ngôø trôû neân khoâng caân xöùng. Maøn hình bò leäch taâm hay OSD khoâng theå ñieàu chænh ñöôïc. LED ñang nhaáp nhaùy nhöng khoâng coù hình aûnh treân maøn hình. Danh saùch kieåm tra Caùc giaûi phaùp Baïn ñaõ khoùa meny On Screen Haõy môû khoùa OSD baèng caùch nhaán Display (OSD) ñeå ngaên chaëng nuùt MENU ít nhaát trong 5 giaây. caùc thay ñoåi chaêng? Coù phaûi maøn hình chæ coù moät maøu nhö Haõy kieåm tra vieäc noái caùp tín hieäu. theå ñöôïc nhìn qua giaáy kieáng khoâng? Haõy chaéc chaén raèng card hình aûnh ñaõ ñöôïc aán chaët vaøo trong raõnh daønh cho card video. Coù phaûi maøn hình co nhöõng maøu Haõy khôûi ñoäng laïi maùy tính. saéc kì laï sau khi chaïy moät chöông trình hay vì coù söï xung ñoät giöõa caùc chöông trình öùng duïng khoâng? Card hình aûnh coù ñöôïc caøi ñaët Haõy caøi card hình aûnh sau khi ñoïc ñuùng chöa? höôùng daãn caøi card hình aûnh. Söû duïng OSD ñeå ñieàu chænh kích Baïn coù thay ñoåi card hình aûnh thöôùc vaø vò trí cuûa maøn hình. hay trình ñieàu khieån khoâng? Baïn coù ñieàu chænh ñoä phaân giaûi vaø Ñieàu chænh ñoä phaân giaûi vaø taàn soá cuûa taàn soá maøn hình khoâng? card hình aûnh. (Xem phaàn Caùc cheá ñoä hieån thò ñònh tröôùc). Maøn hình coù theå khoâng caân xöùng do chu kyø tín hieäu cuûa card hình aûnh. Ñieàu chænh laïi vò trí baèng caùch söû duïng OSD. Baïn coù ñieàu chænh ñoä phaân giaûi vaø Ñieàu chænh ñoä phaân giaûi vaø taàn soá cuûa taàn soá maøn hình khoâng? card hình aûnh. (Xem phaàn Caùc cheá ñoä hieån thò ñònh tröôùc). Taàn soá coù ñöôïc ñieàu chænh ñuùng Ñieàu chænh taàn soá thích hôïp baèng caùch khi baïn kieåm tra Thôøi haïn Hieån thò tham khaûo Höôùng daãn söû duïng card treân menu khoâng? hình aûnh vaø Caùc cheá ñoä hieån thò ñònh tröôùc. (Taàn soá toái ña cho moãi ñoä phaân giaûi coù theå thay ñoåi tuøy theo daïng saûn phaåm.) Cheá ñoä maøu cuûa Windows coù Ñoái vôùi Windows ME/2000/XP: Maøn hình chæ hieån thò toái ña ñöôïc caøi ñaët ñuùng khoâng? Haõy thieát laäp maøu thích hôïp baèng caùch 16 maøu. vaøo Control Panel, Display, Settings. Maøu treân maøn hình thay ñoåi sau khi baïn ñoåi card hình Card hình aûnh coù ñöôïc caøi ñaët Haõy caøi card hình aûnh sau khi ñoïc aûnh. ñuùng chöa? höôùng daãn caøi card hình aûnh. Baïn seõ thaáy moät thoâng baùo Baïn ñaõ caøi ñaët chöông trình ñieàu Haõy caøi ñaët chöông trình ñieàu khieån nhö sau: “Unrecognized khieån maøn hình chöa? maøn hình theo Caùc höôùng daãn Caøi ñaët monitor, Plug & Play (VESA Trình ñieàu khieån. Haõy xem saùch Höôùng daãn caøi card Haõy caøi ñaët chöông trình ñieàu khieån DDC) monitor found”. hình aûnh ñeå xem caùc chöùc naêng maøn hình theo Caùc höôùng daãn Caøi ñaët Plug & Play (VESA DDC) coù ñöôïc Trình ñieàu khieån. hoã trôï khoâng. 19 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 20 Ñaëc Tính Kyõ Thuaät Ñaëc Tính Chung Kieåu Maùy SyncMaster 152T Maøn hình LCD Kích thöôùc 15,0 inch theo ñöôøng cheùo Vuøng hieån thò 304,1(ngang) x 228,1 (doïc) Kích thöôùc ñieåm aûnh 0,297 (ngang) x 0,297 (doïc) Loaïi a-si TFT maøn hình ma traän ñoäng Goùc nhìn 160/130(ngang/doïc) Hieån Thò 30 ~ 61 kHz Ngang Doïc 56 ~ 75 Hz Hieån Thò Maøu 16,294,277 maøu Ñoä phaân giaûi Ñoä phaân giaûi toái öu 1024 x 768@ 60Hz Ñoä Phaân Giaûi Lôùn Nhaát 1024 x 768@ 75Hz Giao dieän treo VESA RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG (daây caùp tuøy choïn), 0,7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative Xung Clock Cöïc Ñaïi 80 MHz Nguoàn Ñieän Caáp AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Caùp tín hieäu caùp 15 chaân D-sub, coù theå thaùo rôøi, DVI-D ~ DVI-D, coù theå thaùo rôøi Möùc tieâu thuï ñieän naêng Toái ña 31 W Kích thöôùc (roäng x daøy x cao)/Troïng löôïng 357,5 X 184,5 X 361,6mm (Sau khi laép ñaët chaân ñeá) / 2,9kg (vôùi Chaân ñeá Bagic) 357,5 X 50,7 X 288,5mm (Sau khi gaäp chaân ñeá) / 3,1 kg (Chaân ñeá ña phöông tieän) VESA Mounting Interface 75mm x 75mm (duøng vôùi boä phaän treo ñaëc bieät (tay). Moâi Tröôøng Nhieät ñoä: 50°F ~ 104°F(10°C ~ 40°C) Ñoä aåm 10% ~ 80%, khoâng taäp trung. Khi Maùy Hoaït Ñoäng Nhieät ñoä: -4°F ~113°F (-20°C ~ 45°C) Ñoä aåm 5% ~ 95%, khoâng taäp trung. Khi Löu Giöõ Ñieåm aûnh chaáp nhaän ñöôïc "Maøn hình TFT LCD ñöôïc saûn xuaát baèng coâng ngheä baùn daãn tieân tieán vôùi ñoä chính xaùc 99,999% ñoái vôùi saûn phaåm naøy. Nhöng caùc ñieåm aûnh RED (ÑOÛ), GREEN (XANH LAÙ), BLUE (XANH LAM) vaø WHITE (TRAÉNG) ñoâi luùc coù veû hôi saùng hoaëc baïn coù theå thaáy moät soá ñieåm aûnh ñen. Tình traïng naøy khoâng phaûi do chaát löôïng xaáu vaø baïn coù theå söû duïng maùy maø khoâng phaûi baên khoaên gì. Ví duï, toång soá ñieåm aûnh TFT LCD coù trong saûn phaåm naøy laø 2.359.296" Cheá Ñoä Plug & Play Maøn hình ñöôïc caøi ñaët cheá ñoä Plug & Play. Söï töông thích giöõa maøn hình vaø maùy tính seõ cung caáp ñieàu kieän hoaït ñoäng vaø caøi ñaët toát nhaát. Trong tröôøng hôïp toát nhaát quaù trình caøi ñaët seõ töï ñoäng, tröø phi, ngöôøi söû duïng muoán caøi ñaët tuaàn töï. Ghi chuù Kieåu daùng vaø ñaëc tính kyõ thuaät coù theå thay ñoåi maø khoâng caàn phaûi baùo tröôùc. 20 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 21 Ñaëc Tính Kyõ Thuaät Ñaëc Tính Chung Kieåu Maùy SyncMaster 172T Maøn hình LCD Kích thöôùc 17,0 inch theo ñöôøng cheùo Vuøng hieån thò 337,92(ngang) x 270,336 (doïc) Kích thöôùc ñieåm aûnh 0,264 (ngang) x 0,264 (doïc) Loaïi a-si TFT maøn hình ma traän ñoäng Goùc nhìn 170/170 (ngang/doïc) Hieån Thò 30 ~ 81 kHz Ngang Doïc 56 ~ 75 Hz Hieån Thò Maøu 16,294,277 maøu Ñoä phaân giaûi Ñoä phaân giaûi toái öu 1280 x 1024@ 60Hz Ñoä Phaân Giaûi Lôùn Nhaát 1280 x 1024@ 75Hz Giao dieän treo VESA RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG (daây caùp tuøy choïn), 0,7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative Xung Clock Cöïc Ñaïi 140 MHz Nguoàn Ñieän Caáp AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Caùp tín hieäu caùp 15 chaân D-sub, coù theå thaùo rôøi, DVI-D ~ DVI-D, coù theå thaùo rôøi Möùc tieâu thuï ñieän naêng Toái ña 42 W Kích thöôùc (roäng x daøy x cao)/Troïng löôïng 385 X 216 X 404.7mm (Sau khi laép ñaët chaân ñeá) / 4,7kg (vôùi Chaân ñeá Bagic) 385 X 56.8 X 324.7mm (Sau khi gaäp chaân ñeá) / 4,7 kg (Chaân ñeá ña phöông tieän) VESA Mounting Interface 75mm x 75mm (duøng vôùi boä phaän treo ñaëc bieät (tay). Moâi Tröôøng Nhieät ñoä: 50°F ~ 104°F(10°C ~ 40°C) Ñoä aåm 10% ~ 80%, khoâng taäp trung. Khi Maùy Hoaït Ñoäng Nhieät ñoä: -4°F ~113°F (-20°C ~ 45°C) Ñoä aåm 5% ~ 95%, khoâng taäp trung. Khi Löu Giöõ Ñieåm aûnh chaáp nhaän ñöôïc "Maøn hình TFT LCD ñöôïc saûn xuaát baèng coâng ngheä baùn daãn tieân tieán vôùi ñoä chính xaùc 99,999% ñoái vôùi saûn phaåm naøy. Nhöng caùc ñieåm aûnh RED (ÑOÛ), GREEN (XANH LAÙ), BLUE (XANH LAM) vaø WHITE (TRAÉNG) ñoâi luùc coù veû hôi saùng hoaëc baïn coù theå thaáy moät soá ñieåm aûnh ñen. Tình traïng naøy khoâng phaûi do chaát löôïng xaáu vaø baïn coù theå söû duïng maùy maø khoâng phaûi baên khoaên gì. Ví duï, toång soá ñieåm aûnh TFT LCD coù trong saûn phaåm naøy laø 3.932.160" Cheá Ñoä Plug & Play Maøn hình ñöôïc caøi ñaët cheá ñoä Plug & Play. Söï töông thích giöõa maøn hình vaø maùy tính seõ cung caáp ñieàu kieän hoaït ñoäng vaø caøi ñaët toát nhaát. Trong tröôøng hôïp toát nhaát quaù trình caøi ñaët seõ töï ñoäng, tröø phi, ngöôøi söû duïng muoán caøi ñaët tuaàn töï. Ghi chuù Kieåu daùng vaø ñaëc tính kyõ thuaät coù theå thay ñoåi maø khoâng caàn phaûi baùo tröôùc. 21 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 22 Ñaëc Tính Kyõ Thuaät Ñaëc Tính Chung Kieåu Maùy SyncMaster 192T Maøn hình LCD Kích thöôùc 19,0 inch theo ñöôøng cheùo Vuøng hieån thò 376,32(ngang) x 301,056 (doïc) Kích thöôùc ñieåm aûnh 0,297 (ngang) x 0,297 (doïc) Loaïi a-si TFT maøn hình ma traän ñoäng Goùc nhìn 170/170 (ngang/doïc) Hieån Thò 30 ~ 81 kHz Ngang Doïc 56 ~ 75 Hz Hieån Thò Maøu 16,194,277 maøu Ñoä phaân giaûi Ñoä phaân giaûi toái öu 1280 x 1024@ 60Hz Ñoä Phaân Giaûi Lôùn Nhaát 1280 x 1024@ 75Hz Giao dieän treo VESA RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG (daây caùp tuøy choïn), 0,7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative Xung Clock Cöïc Ñaïi 140 MHz Nguoàn Ñieän Caáp AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Caùp tín hieäu caùp 15 chaân D-sub, coù theå thaùo rôøi, DVI-D ~ DVI-D, coù theå thaùo rôøi Möùc tieâu thuï ñieän naêng Toái ña 45 W Kích thöôùc (roäng x daøy x cao)/Troïng löôïng 431 X 220 X 447mm (Sau khi laép ñaët chaân ñeá) / 5,5kg (vôùi Chaân ñeá Bagic) 431 X 29,7 X 324,7mm (Sau khi gaäp chaân ñeá) / 5,6 kg (Chaân ñeá ña phöông tieän) VESA Mounting Interface 75mm x 75mm (duøng vôùi boä phaän treo ñaëc bieät (tay). Moâi Tröôøng Nhieät ñoä: 50°F ~ 104°F(10°C ~ 40°C) Ñoä aåm 10% ~ 80%, khoâng taäp trung. Khi Maùy Hoaït Ñoäng Nhieät ñoä: -4°F ~113°F (-20°C ~ 45°C) Ñoä aåm 5% ~ 95%, khoâng taäp trung. Khi Löu Giöõ Ñieåm aûnh chaáp nhaän ñöôïc "Maøn hình TFT LCD ñöôïc saûn xuaát baèng coâng ngheä baùn daãn tieân tieán vôùi ñoä chính xaùc 99,999% ñoái vôùi saûn phaåm naøy. Nhöng caùc ñieåm aûnh RED (ÑOÛ), GREEN (XANH LAÙ), BLUE (XANH LAM) vaø WHITE (TRAÉNG) ñoâi luùc coù veû hôi saùng hoaëc baïn coù theå thaáy moät soá ñieåm aûnh ñen. Tình traïng naøy khoâng phaûi do chaát löôïng xaáu vaø baïn coù theå söû duïng maùy maø khoâng phaûi baên khoaên gì. Ví duï, toång soá ñieåm aûnh TFT LCD coù trong saûn phaåm naøy laø 3.932.160" Cheá Ñoä Plug & Play Maøn hình ñöôïc caøi ñaët cheá ñoä Plug & Play. Söï töông thích giöõa maøn hình vaø maùy tính seõ cung caáp ñieàu kieän hoaït ñoäng vaø caøi ñaët toát nhaát. Trong tröôøng hôïp toát nhaát quaù trình caøi ñaët seõ töï ñoäng, tröø phi, ngöôøi söû duïng muoán caøi ñaët tuaàn töï. Ghi chuù Kieåu daùng vaø ñaëc tính kyõ thuaät coù theå thay ñoåi maø khoâng caàn phaûi baùo tröôùc. 22 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 23 Cheá Ñoä Hieån Thò Neáu tín hieäu ñöôïc truyeàn ñi töø maùy töông öùng vôùi Caùc cheá ñoä caøi ñaët veà thôøi gian sau ñaây, maøn hình seõ ñöôïc ñieàu chænh töï ñoäng. Tuy nhieân, neáu tín hieäu khaùc, maøn hình seõ bò traéng trong khi ñeøn chæ thò vaãn saùng. Chænh card maøn hình theo baûng thoâng soá döôùi ñaây. Cheá ñoä hieån thò Taàn soá queùt ngang (kHz) Taàn soá queùt doïc (Hz) Xung clock (MHz) Sync Polarity (H/V) SyncMaster 172T/192T MAC. 640 x 480 35,000 66,667 30,240 -/- MAC. 832 x 624 49,726 74,551 57,284 -/- IBM. 640 x 350 31,469 70,086 25,175 +/- IBM. 640 x 480 31,469 59,940 25,175 -/- IBM. 720 x 400 31,469 70,087 28,322 -/+ VESA. 640 x 480 37,500 75,000 31,500 -/- VESA. 640 x 480 37,861 72,809 31,500 -/- VESA. 800 x 600 35,156 56,250 36,000 +.-/+.- VESA. 800 x 600 37,879 60,317 40,000 +/+ VESA. 800 x 600 46,875 75,000 49,500 +/+ VESA. 800 x 600 48,077 72,188 50,000 +/+ VESA. 1024 x 768 48,363 60,004 65,000 -/- VESA. 1024 x 768 56,476 70,069 75,000 -/- VESA. 1024 x 768 60,023 75,029 78,750 +/+ SyncMaster 152T/172T/192T SyncMaster 172T/192T VESA. 1280 x 1024 63,981 60,020 108,00 +/+ VESA. 1280 x 1024 79,976 75,025 135,00 +/+ SUN. 1280 x 1024 81,129 76,106 135,00 -/- Taàn soá queùt ngang Thôøi gian queùt töø phaûi sang traùi cuûa chieàu ngang maøn hình goïi laø chu kyø queùt ngang vaø nghòch ñaûo cuûa chu kyø queùt ngang goïi laø taàn soá queùt. Ñôn vò : kHz Taàn soá queùt doïc Gioáng nhö ñeøn huyønh quang, maøn hình seõ laëp laïi hình aûnh nhieàu laàn treân 4 giaây ñeå hieån thò aûnh. Taàn soá cuûa söï laëp laïi naøy ñöôïc goïi laø taàn soá queùt doïc. Ñôn vò : Hz. 23 152_172_192T-vet.qxd 8/25/2003 9:54 PM Page 24 MEMO