Download Operating Instructions

#,52:'
'PINKUJDQQMࡍ࡯ࠫ㧞㧜㧜㧡ᐕ㧟᦬㧞ᣣ‫ޓ‬᳓ᦐᣣ‫ޓ‬ඦᓟ㧡ᤨ㧞㧜ಽ
2-7 Warning and
Functions
Status
Display
2-8 Display Window Functions
P2 card/battery-remaining level indications
Media-remaining space indication bar
The bar indicates the remaining free space on each P2 card, using a
seven-segment display.
Each segment can represent either three or five minutes of remaining
free space, depending on the value set through the menu option
CARD REMAIN/„. According to the set value, the segments
disappear one-by-one. The menu option CARD REMAIN /„ can be
found in the <BATTERY/P2CARD> screen on the MAIN OPERATION
page.
SLAVE HOLD W DV GPS
CTL VTCG TIME DATE P- REC
OVER
OVER
0
10
h Y
minM
s D
MEDIA E
BATT E
frm
20
F
30
F
40
OO
LOOP
Back tally lamp
When the
BACK TALLY switch is set to [ON], the lamp
behaves in the same way as the front tally lamp at the
viewfinder.
BACK TALLY switch
This switch controls the action of the
tally lamps.
ON:
OFF:
back and
rear
Back and rear tally lamps enabled.
Back and rear tally lamps disabled.
WARNING lamp
This lamp starts blinking or lights up if something unusual
occurs in the memory.
LIGHT button
Use this button to control illumination of the display window.
Alternately pressing this button toggles illumination of the
display window on or off.
Display window
This window displays warnings, battery-remaining level,
sound volume, time data, and other information.
Rear tally lamp
When the
BACK TALLY switch is set on [ON], the rear
tally lamp behaves in the same way as the back tally lamp.
DRIVE
OP-SLOT
13
-dB
24
Battery-remaining level indication bar
For a battery with a digital indicator (percentage indication), if
the remaining level of the battery is higher than 70%, all seven
segments up to the “F” position are lighted.
When the remaining level falls below 70%, the segments go out
one-by-one for each drop of 10%. All seven segments can be set
to light up when the battery-remaining balance is 100%. To do
so select “100%” for the menu option BATT REMAIN FULL in the
<BATTERY/P2CARD> screen of the MAIN OPERATION page.
Audio channel level meter
When the MONITOR SELECT CH1/2 / CH3/4 switch is set to
[CH1/2], the meter indicates 1 and 2 as the audio channel
numbers, together with their audio levels. When the switch is set
to [CH3/4], the meter indicates 3 and 4 as the audio channel
numbers, together with their audio levels.
Memory action status indication
Error Code Indication (for more information, see [7-3
Warning System])
SLAVE HOLD W DV GPS
CTL VTCG TIME DATE P- REC
OVER
OVER
0
10
h Y
minM
MEDIA E
BATT E
s D
frm
20
F
30
F
40
OO
LOOP
DRIVE
OP-SLOT
13
-dB
24
Information indication
LOOP:
Stays illuminated in LOOP REC mode. For information
about the LOOP REC mode, see [3-5 Loop Recording].
DRIVE:
Stays illuminated when the menu option USB is set to
“ON”.The menu option USB can be found in the
<SYSTEM MODE> screen on the SYSTEM SETTING
page.
OP-SLOT: Remains illuminated when a video encoder card is
operated in the optional slot.
20