Download SERVICE MANUAL

XDR-S3HD
SERVICE MANUAL
US Model
Ver. 1.0 2007. 05
HD Radio Broadcasting was approved by the Federal
Communications Commission in October 2002 as the system
for digital AM and FM broadcasting in the U.S.
HD Radio technology features include:
– Static-free, clear radio reception.
– FM Multicasting – the ability to broadcast multiple program
streams over a single FM frequency.
– A variety of “data services,” including text-based
information – artist name, song title, etc. scrolled across your
receiver display.
– Digital broadcasts in the same frequencies as analog
broadcasts; listeners do not need to learn a new station
number and today’s stations remain at their current place on
the dial.
HD Radio technology is developed and licensed by iBiquity
Digital Corporation and supported by the leaders of the
broadcasting, consumer electronics and automotive industries.
HD RadioTM Technology Manufactured Under License From
iBiquity Digital Corporation. iBiquity Digital, the HD Radio
logo, and the HD logo are registered trademarks of iBiquity
Digital Corporation. HD RadioTM is a trademark of iBiquity
Digital Corporation. U.S. and Foreign Patents.
SPECIFICATIONS
Time display
Frequency range
Speaker
Output
Input
Antenna terminal
Power output
Power requirements
Dimensions
Mass
Supplied accessories
12-hour system
FM : 87.5 – 108 MHz
AM : 530 – 1,710 kHz
Approx. 6.6 cm (2 5/8 inches) dia. 4 Ω
i (headphone) jack (φ 3.5 mm stereo minijack)
LINE IN jack (φ 3.5 mm stereo minijack)
75 Ω antenna terminal for FM
Antenna terminal for AM
2.8 W + 2.8 W (at 10% harmonic distortion)
120 V AC, 60 Hz
Approx. 300 × 120 × 169 mm (w/h/d)
(11 7/8 × 4 3/4 × 6 3/4 inches) not incl. projecting
parts and controls
Approx. 3.6 kg (7 lb 15.8 oz) incl. power supply unit
Remote commander (1)
FM wire antenna (1)
FM dipole antenna (1)
AM loop antenna (1)
Audio connecting cable (1)
Design and specifications are subject to change
without notice.
FM/AM DIGITAL RADIO
9-887-734-01
Sony Corporation
2007E04-1
© 2007. 05
Personal Audio Division
Published by Sony Techno Create Corporation
1
XDR-S3HD
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part
having a return to chassis, must not exceed 0.5 mA (500
microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to use
these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range
are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
voltmeter
(0.75 V)
SERVICE NOTES
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1. GENERAL ........................................................................... 3
2. DISASSEMBLY
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
Panel (Front) Assy ............................................................... 6
DC Fan (M950) ................................................................... 7
Wires ................................................................................... 7
Chassis Assy ........................................................................ 8
MAIN Board ....................................................................... 8
POWER Board .................................................................... 9
KEY Board .......................................................................... 9
VOL Board, TUNE Board ................................................ 10
Assembly of the Power Cord ............................................ 10
3. DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
Block Diagram .................................................................. 11
Printed Wiring Board – Main Section – ............................ 13
Schematic Diagram – Main Section – ............................... 14
Printed Wiring Boards – Power Section – ......................... 15
Schematic Diagram – Power Section – ............................. 16
Printed Wiring Board – Micon Section – .......................... 17
Schematic Diagram – Micon Section – ............................. 18
Printed Wiring Boards – Key Section – ............................ 19
Schematic Diagram – Key Section – ................................ 20
4. EXPLODED VIEWS
4-1.
4-2.
4-3.
4-4.
4-5.
Main Section ..................................................................... 25
Front Panel Section ........................................................... 26
KEY Board Section ........................................................... 27
Cabinet Section ................................................................. 28
Chassis Section ................................................................. 29
5. ELECTRICAL PARTS LIST ........................................ 30
XDR-S3HD
SECTION 1
GENERAL
A
Setting the clock
1
2
Plug in the unit.
The display will flash “AM 12:00.”
Press MENU to show the menu display.
This section is extracted
from instruction manual.
Tip
The preset can be selected by pressing the number
button of the remote commander. Press ENTER after
the preset number is selected.
—Scan tuning
The unit will automatically scan the selected band.
In HD scan, HD Radio stations are scanned.
POWER
SLEEP
BAND
RADIO / LINE IN
PRESET
TONE
DISPLAY
MENU
1
2
3
4
ENTER
VOLUME
TUNE/SELECT
3
ANTENNA
AM
RESET
Turn TUNE/SELECT clockwise to select
“TIME SET,” then press ENTER.
The hour will start to flash in the display.
5
FM
4
LINE IN
5
Turn TUNE/SELECT clockwise or
counterclockwise until current hour appears in
the display, then press ENTER.
The hour is set and the minutes start to flash.
Repeat step 4 to set the minute.
Note
If you do not set the menu within 65 seconds, the setting
mode is canceled.
To change the display to the
daylight saving time
(summer time) indication
1 Press MENU to show the menu display.
2 Turn TUNE/SELECT clockwise or
3
AC power cord
counterclockwise to select “DST,” then press
ENTER.
Turn TUNE/SELECT counterclockwise to
select “ON,” then press ENTER.
“ ” appears and the time indication changes to
summer time.
To deactivate the DST function, select “OFF” in step 3.
Playing the radio
AM FM SIRIUS XM SLEEP ALARM
—Manual tuning
1 Press POWER to turn on the radio.
2
3
4
B
6
7
Press POWER to turn on the radio.
Press BAND to select the band AM or FM.
Press MENU to show the menu display.
Turn TUNE/SELECT clockwise or
counterclockwise to select “SCAN” or “HD
SCAN,” then press ENTER.
Scanning of the selected band starts.
When a station is received, scanning pauses for 3
seconds and then continues.
When the unit tunes in to the desired station,
do any of the following operations to stop
scanning.
– Press ENTER on the unit or remote commander.
– Press SCAN or HD SCAN on the remote
commander.
If necessary, turn TUNE/SELECT
clockwise or counterclockwise to tune in to
the station more precisely.
Adjust the volume using VOLUME.
Tip
You can scan a station directly by pressing SCAN or
HD SCAN on the remote commander.
To listen with the
headphones
You can enjoy the radio and external equipment
connected to the line in by the headphones (not
supplied). Connect the headphones (not supplied) to the
i (headphone) jack. The speaker is deactivated when
the headphones are connected.
Changing the
display mode and
settings
To change the display mode
Press DISPLAY.
The display changes as follows:
When an analog radio station is received
If “LINE IN” is displayed, press RADIO/LINE IN
so that the band (AM or FM) appears.
Press BAND to select the band AM or FM.
Turn TUNE/SELECT clockwise or
counterclockwise to tune in to a desired
frequency.
x
A beep sounds when the minimum frequency of
each band is received during tuning.
Adjust the volume using VOLUME.
Tip
To attenuate the volume, turn VOLUME
counterclockwise quickly.
POWER
Note
The frequency cannot be input with the number buttons
of the remote commander.
ALARM
SLEEP
1
2
3
—Preset tuning
4
5
6
You can preset 20 stations each for AM and FM.
7
8
9
0
ENTER
Presetting a station
1 Follow steps 1 to 3 in “Manual tuning” to
tune the frequency you wish to preset.
2 Press and hold PRESET for a few seconds.
PRESET
TUNE/
SELECT
MENU
VOL
You will hear a beep.
Field strength level indicator
Preset number*
Band
Frequency
Current time
* When you tune in a station by selecting a preset
number.
When an analog FM broadcast that supports
RBDS (Radio Broadcast Data System) is
received
TONE
HD SCAN
BAND
SCAN
RADIO/
LINE IN
BRIGHT
DISPLAY
3
Size AAA (R03)
×2
A
B
C
D
E
Turn TUNE/SELECT clockwise or
counterclockwise to select the preset number,
then press ENTER.
x
The frequency is stored in the selected preset
number and you will hear a beep.
The number 5 and the VOL +
buttons have a tactile dot.
To preset another station, repeat these steps.
Note
If you try to store another station in the same preset
number, the previously stored station will be replaced.
Preparing the
remote commander
When to replace the batteries
With normal use, the batteries should last for about six
months. When the remote commander no longer
operates the unit, replace all the batteries with new ones.
Tuning in to a station
1 Press POWER to turn on the radio.
2 Press BAND to select the band AM or FM.
3 Press PRESET.
Installing the batteries into the remote
commander (See Fig. B)
Notes
• Do not charge dry batteries.
• When you are not going to use the remote commander
for a long time, remove the batteries to avoid any
damage caused by leakage and corrosion.
4
Insert two size AAA (R03) batteries (not supplied).
5
x
The preset number appears in upper left in the
display.
Turn TUNE/SELECT clockwise or
counterclockwise to select the preset number.
Adjust the volume using VOLUME.
x
3
XDR-S3HD
or
Adjusting the tone
1
2
Field strength level indicator
Preset number*
Band
Station name
Name of station currently tuned in.
E Frequency
F Text information
Text information transmitted from station.
G Current time
Press POWER to turn on the radio.
Press TONE to show the tone setting
display.
A
B
C
D
3
* When you tune in a station by selecting a preset
number.
4
Note
The display item differs depending on the content of a
broadcast or the station.
5
When an HD Radio station is received
Turn TUNE/SELECT clockwise or
counterclockwise to set “TREBLE,” then
press TONE.
Turn TUNE/SELECT clockwise or
counterclockwise to set “BASS,” then press
TONE.
Turn TUNE/SELECT clockwise or
counterclockwise to set “SURROUND,” then
press TONE.
Tip
The adjustable range of “TREBLE” and “BASS” is from
–6 to +6.
“SURROUND” switches “ON” or “OFF.”
x
Setting the alarm
To deactivate the alarm function, turn TUNE/SELECT
clockwise to select “OFF” in step 3.
To stop the alarm
Press POWER on the unit or remote commander.
Tips
• To enter “ALARM TIME SET” mode directly, press
and hold ALARM on the remote commander for 2
seconds.
• You can activate or deactivate the alarm function
directly by pressing ALARM on the remote
commander.
Notes
• If you do not set the menu within 10 seconds, the
setting mode is canceled.
• If you do not operate the unit for 60 minutes after
alarm sounds, the power is turned off.
• If you select “LINE IN” source in “ALARM TIME
SET,” start playback on the external equipment. You
cannot control the external equipment from this unit.
Setting the sleep
timer
You can enjoy falling asleep to the radio using the builtin sleep timer that turns off the radio automatically after
a preset duration.
1
Press SLEEP.
“SLEEP” and the digits for the sleep timer duration
appear.
You can set the unit to turn on automatically at a preset
time. The alarm can be set, even if the unit is off.
To adjust the hour and minute, see “Setting the clock.”
x
counterclockwise to select “ALARM TIME
SET,” then press ENTER.
The hour sign starts flashing.
2
If you press SLEEP while the unit is turned off, the
unit is turned on.
Press SLEEP repeatedly to select the desired
sleep timer setting.
Each press changes the setting time as follows:
60
A HD indicator
Lights: HD Radio reception level is sufficient
(indicator flashes momentarily, and then
stays lit).
The sound changes from analog to digital.
Flashes: HD Radio reception level is too low.
The sound stays analog.
If a HD Radio station signal is very weak, the
indicator will not flash.
B Field strength level indicator
C Preset number*
D Current station’s call letters
E Band
F Station name and information
G Title/Artist name
H Sub channel (FM only)
Appears when HD Radio broadcasts multiple
program.
Turn TUNE/SELECT clockwise or
counterclockwise to select a sub channel.
I Frequency
J Current time
K Text information
* When you tune in a station by selecting a preset
number
Note
The display item differs depending on the content of a
broadcast or the station.
4
5
6
7
3
counterclockwise to select “BRIGHTNESS”
or “CONTRAST,” then press ENTER.
Turn TUNE/SELECT clockwise or
counterclockwise to select the setting or to
adjust the level, then press ENTER.
Turn TUNE/SELECT clockwise or
counterclockwise to set the hour, then press
ENTER.
The minute sign starts flashing.
Turn TUNE/SELECT clockwise or
counterclockwise to set the minutes, then
press ENTER.
Tip
You can adjust “BRIGHTNESS” directly by pressing
BRIGHT on the remote commander.
4
15
OFF
To change the sleep timer setting
You can press SLEEP repeatedly to select the desired
sleep timer setting even after the sleep timer has been
activated.
To deactivate the sleep timer
The source sign starts flashing.
Press POWER to turn off the unit before the setting
time has elapsed, or press SLEEP repeatedly to set the
sleep timer to “SLEEP OFF” in step 2.
If you select “RADIO AM,” “RADIO FM” or
“LINE IN” continue the following steps.
Listening to the
external equipment
Turn TUNE/SELECT clockwise or
counterclockwise to select the source from
“RADIO AM,” “RADIO FM,” “LINE IN” or
“BUZZER,” then press ENTER.
Turn TUNE/SELECT clockwise or
counterclockwise to select the preset number,
then press ENTER.
1
If you selected “LINE IN” in step 5, this step is not
necessary.
Turn TUNE/SELECT clockwise or
counterclockwise to set the volume, then
press ENTER.
Connect the LINE IN jack of the unit to the
line out jack or headphone jack of the external
equipment using the audio connecting cable
(supplied).
ANTENNA
AM
RESET
FM
counterclockwise to select “ALARM SET,”
then press ENTER.
Turn TUNE/SELECT counterclockwise to
select “ON,” then press ENTER.
“ALARM” appears in the display.
Example of display when unit is off
LINE IN
Audio connecting cable
(supplied)
If you press DISPLAY while the display above
appears, the display changes to the following.
BRIGHTNESS:
The brightness of the display is selected from
“HIGH,” “MIDDLE” or “LOW.”
CONTRAST:
The contrast of the display can be adjusted by 11
levels.
Note
If you do not set the menu within 10 seconds, the setting
mode is canceled.
30
The unit automatically turns off when the duration time
is passed.
To set the alarm
1 Press MENU to show the menu display.
2 Turn TUNE/SELECT clockwise or
3
To change the display
settings (BRIGHTNESS/
CONTRAST)
1 Press MENU to show the menu display.
2 Turn TUNE/SELECT clockwise or
45
A beep sounds when the display returns to “SLEEP
60.”
After about 4 seconds, “SLEEP” lights in the display
when the duration time is set.
3
To external
equipment
2
3
Press POWER to turn on the radio.
Press RADIO/LINE IN to select “LINE
IN” in the display.
To return to the previous display, press DISPLAY
again.
A
B
C
D
ALARM indicator
Alarm setting time
Alarm setting (Source, Frequency, etc.)
Current time
Press RADIO/LINE IN.
The band (AM or FM) is shown in the display.
Notes
• Refer also to the connected equipment’s manual.
• The supplied audio connecting cable may not be used
with some external equipment. In this case, use a cord
suitable for the external equipment you are using.
• When you listen to the radio with external equipment
connected, turn off the connected equipment because
noise may be caused. If noise continues, even when
the equipment is turned off, disconnect and place the
external equipment away from the unit.
Resetting the unit
The RESET button is located on the rear of the unit.
Press this button with a pointed object if the radio fails
to function properly. The clock settings and stations you
have preset, etc., will revert to the factory preset.
Buttons shared on both the remote commander and the
unit control the same functions.
Example of display when unit is off
If you press DISPLAY for 2 seconds while the
display above appears, the beep is heard and the
scroll speed of the display item becomes slow.
To return to normal scroll speed, press DISPLAY
again for 2 seconds.
To return to the radio
Using the remote
commander
To set the alarm time
1 Press MENU to show the menu display.
2 Turn TUNE/SELECT clockwise or
or
Tip
To display the current time, press DISPLAY.
4
5
Play the equipment connected to the LINE IN
jack.
Adjust the volume using VOLUME.
VOL +/— buttons
To adjust the volume.
Press and hold the VOL – button for 2.5 seconds, the
volume becomes minimized.
ALARM button
Press to set the alarm to “ON” or “OFF.”
Press and hold for 2 seconds to enter “ALARM TIME
SET.”
HD SCAN button
The selected band is scanned, and receivable HD Radio
stations are received for 3 seconds in order of frequency.
SCAN button
The selected band is scanned, and receivable radio
stations are received for 3 seconds in order of frequency.
BRIGHT button
To adjust the brightness of the display.
Number buttons
To select a preset number (1 to 20).
Press ENTER after the preset number is selected.
If you input the number 0 or more than 21 and press
ENTER, “ERROR” appears in the display.
XDR-S3HD
Connecting the
antenna
To connect the AM loop
antenna
The shape and the length of the antenna is designed to
receive AM signals. Do not dismantle or roll up the
antenna.
1
2
3
Remove only the loop part from the plastic
stand.
Set up the AM loop antenna.
Connect the cords to the AM antenna
terminals.
Cord (A) or cord (B) can be connected to either
terminal.
Insert the cord while
pushing down the
terminal clamp.
A
4
B
Only insert up
to here.
Make sure the AM loop antenna is connected
firmly by pulling softly.
Adjusting the AM loop antenna
Find a place and an orientation that provide good
reception.
• Do not place the AM loop antenna near the unit or
other AV equipment, as noise may result.
• If you use an external polarized AM antenna, be sure
to connect the ground cord to the U terminal. The
supplied AM antenna cord has no polarity.
Tip
Adjust the direction of the AM loop antenna for best AM
broadcast sound.
To connect the FM antenna
This unit comes supplied with an FM wire antenna and
FM dipole antenna. Connect an antenna that provides
good reception to the FM antenna terminal.
FM wire antenna
(supplied)
FM dipole antenna
(supplied)
Adjusting the FM wire antenna
Be sure to fully extend the FM wire antenna, and keep it
as horizontal or vertical as possible.
Adjusting the FM dipole antenna
Be sure to fully extend the FM dipole antenna. Attach
the antenna in the shape of a T to a high position on a
wall away from this unit.
Tip
If you have poor FM reception, use a 75 Ω coaxial cable
(not supplied) to connect the unit to an outdoor FM
antenna as shown below.
ANTENNA
Outdoor FM antenna
5
XDR-S3HD
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1.
PANEL (FRONT) ASSY
(Page 6)
2-2.
DC FAN (M950)
(Page 7)
2-3.
WIRES
(Page 7)
2-4.
CHASSIS ASSY
(Page 8)
2-5.
MAIN BOARD
(Page 8)
2-6.
POWER BOARD
(Page 9)
2-9.
ASSEMBLY OF THE POWER CORD
(Page 10)
2-7.
KEY BOARD
(Page 9)
2-8.
VOL BOARD,
TUNE BOARD
(Page 10)
Note : Follow the disassembly procedure in the numerical order given.
2-1. PANEL (FRONT) ASSY
CN305
6 wire (3P)
(CN305)
red
5 flexible flat cable (18 core)
(CN5)
CNT board
red
CN306
7 wire (6P)
(CN306)
3 five wood screws
(+R 3.1 × 13)
4
8 panel (front) assy
2 five wood screws
(+R 3.1 × 13)
1 speaker net sub assy
6
XDR-S3HD
2-2. DC FAN (M950)
1 two screws
((+) BV tapping (B3))
2 two screws
((+) BV tapping (B3))
6 two screws
((+) BV tapping (B3))
5 two screws
((+) BV tapping (B3))
3
8 cover (fan)
7 DC fan (M950)
4 CN950 (2P)
2-3. WIRES
from KEY board
from VOL board
from TUNE board
red
red
red
CN305
CN304
from speaker (L-ch)
red
red
from speaker (R-ch)
CN302
7
XDR-S3HD
2-4. CHASSIS ASSY
1 screw
((+) BV tapping (B3))
4 Pull the chassis assy
out while pressing
the power cord in the
direction of the arrow.
7 chassis assy
black
green
2 two screws
((+) BV tapping (B3))
6 power cord
black with line
3 two screws
((+) BV tapping (B3))
5 Remove the three solders.
2-5. MAIN BOARD
4 three screws
((+) BV tapping (B3))
5 two screws
((+) BV tapping (B3))
black
2 Remove the two solders.
6 MAIN board
1 Remove the eight solders.
3 flexible flat cable (10 core)
(CN4)
8
XDR-S3HD
2-6. POWER BOARD
6 three screws
((+) BV tapping (B3))
5 two screws
((+) BV tapping (B3))
7 chassis (upper)
4 wire (6P)
(CN303)
8 POWER board
red
3 FAN CNT board
2 Remove the three solders.
9 chassis (lower)
red
1 two screws
((+) BV tapping (B2.6))
2-7. KEY BOARD
2 two buttons (menu)
4 four buttons (tone)
1 button (power)
3 two buttons (enter)
6 five screws
5 nine springs (button)
7
0 panel (key top)
9 KEY board
8 two screws
9
XDR-S3HD
2-8. VOL BOARD, TUNE BOARD
7 knob (jog)
1 knob (jog)
2 two screws
8 two screws
3
6 escutcheon
9
qs escutcheon
5 VOL board
qa TUNE board
4 two screws
0 two screws
2-9. ASSEMBLY OF THE POWER CORD
When assembling the set, route the power cord
as shown below and install it.
10
XDR-S3HD
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAM
PRE AMP
IC301
R-CH
J301
LINE IN
10
POWER AMP
IC302
IN_L3
AMP
AMP
LOGIC
R-CH
SC
AUDIO_R 26
IN_L1
13
CN1
ANTENNA
2 AM ANT
TRE
SI
6
AUDIO_L 27
1 FM ANT
FM
VOL
L_OUT
BASS
11
10
14
R-CH
R-CH
LCH IN
i
D231
STBY
8
R-CH
20 21
R-CH
R-CH
POWER
CONTROL
Q331,332
R-CH
E2P_SCL 7
SCL 13
+10V
D130
BASS
CONTROL
Q130
SDA 14
• Signal path
: FM
SYSTEM CONTROL
IC401
RESET 12
J380
5
NF
MUTE
Q131
E2P_SDA 8
AM
16
BOUT_LCH
BNF LCH
DSP TUNER UNIT
TU1
CN2
SP201
SPEAKER
L-CH
: AM
BLEND 23
82 VOL_DATA
19 DTUNER_RDS
SDSD_IBOC_OUT_Q
SD_IBOC_OUT_I
BCK_IBOC_OUT
WS_IBOC_OUT
I2S_DATA
I2S_BCK
I2S_WS
RDS 25
30 DTUNER_SDA
29 DTUNER_SCL
86 DTUNER_RESET
89 DTUNER_BLEND
16 17 18 19 20 21 22
AUDIO_MUTE 83
BEEP 28
POWER
CONTROL
Q951,952
AUDIO_STANDBY 84
55
D0 I
I 61
D7 •
63
LIQUID CRYSTAL
DISPLAY PANEL
LCD401
X401
32kHz
+10V
+9V REG
Q903
+5V
WRB 50
RESET
Q403,406
RST 48
AC POWER
UNIT
T901
AC IN ~
POWER
CONTROL
Q901,902
CSB 47
11 XCOUT
M950
DC FAN
A0 49
RDB 51
10 XCIN
2
FAN MOTOR
1
3
DRIVE
IC950
+10V
RST
81 VOL_CLK
8 9 10 11 15 16 17
IF_I2S_Q1
IF_I2S_I1
IF_I2S_BCLK
IF_I2S_WS
AUDIO_I2S_DATA
AUDIO_I2S_BCK
AUDIO_I2S_WS
D904
13 XOUT
X402
5.53MHz
LIGHT1 45
KEY
NETWORK
S801–809
I2C_SCL 12
D402
(LCD BACK LIGHT)
94 KEY1
95 KEY2
LCD BACK
LIGHT CONTROL
Q405
LED+B
BLEND 18
POWER
CONTROL
Q409
S812
TUNE/SELECT
4
+3.3V REG
IC902
5
2
POWER
CONTROL
Q904,905
POWER
CONTROL
Q912,913
73 ENC1_CLK
72 ENC1_DATA
1
3
S1
RESET
74 ENC2_CLK
71 ENC2_DATA
MICON3.3V
REMOTE CONTROL
SIGNAL RECEIVER 1
IC405
LED+B
VOLTAGE
DETECT
Q410
POWER
CONTROL
Q914,915
+1.8V REG
Q5
RESET 12
S813
VOLUME
3 +8.5V REG 1
IC901
KEY3.3V
DTUNER_POWER 87
1
3
+8.5V
D907
MICON3.3V
MICON3.3V
+5V REG
Q906
D401
(LCD BACK LIGHT)
KEE OFF 97
RESET 3
IDM MODULE
IDM1
POWER
CONTROL
Q907,908
PRE 5V
15 XIN
LIGHT2 44
I2C_SDA 13
LCD BACK
LIGHT CONTROL
Q404
2
RESET
IC403
+1.8V REG
Q4
1
CVDD1.8V
4
2
3 +1.8V REG 2
IC2
3 +2.8V REG 1
IC903
4
3 RMT
TH1
THERMAL
DET
Q6
BUFFER
Q7
VDD1.8V
3 +1.8V REG 2
IC1
D912
VDD+3.3V DIG
18 VDET
VDD+3.3V ANA
D911
5 +3.3V REG 1
IC4
BACKUP VDD
BVDD+3.3V
XDR-S3HD
11
11
POWER
CONTROL
Q909,910
+4V REG
Q911
3 +3.3V REG 2
IC3
XDR-S3HD
• Circuit Boards Location
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
KEY board
MAIN board
VOL board
JACK board
for schematic diagrams:
for printed wiring boards:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
%
: indicates tolerance.
f
•
: internal component.
• C : panel designation.
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
f
: internal component.
•
•
: Pattern from the side which enables seeing.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM1
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveform.
• Signal path.
F : FM
f : AM
TUNE board
CNT board
FAN CNT board
MICON board
POWER board
• Waveforms
— MICON Board —
1
IC401 qa (XCOUT)
2.2 Vp-p
32 kHz
1 V/DIV, 10 µsec/DIV
2
IC401 qd (XOUT)
5.53 MHz
1 V/DIV, 0.1 µsec/DIV
XDR-S3HD
12
12
3.1 Vp-p
XDR-S3HD
3-2. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 12 for Circuit Boards Location.
2
1
3
4
5
6
: Uses unleaded solder.
7
8
9
10
11
12
13
14
MAIN BOARD
B
JW25
JW26
A
R61
Q7
BLK
JW3
JW7
JW8
JW11
3
R37
C57
JW12
C
2
C61
1
E
JW32
B
IC3
S1
RESET
S1
C
CN2
FM
WHT
Q6
C58
B
TP1
JW16
R57
1
R25
AM
JW6
Q4
B
R18
IC4
4
5
1
C8
JW31
JC4
JC3
C7
R17
JW23
C16
3 1
C60
C
C59
VIO
E
JC2
WHT
R1
R2
JC5
R51
R52
R19
R3
TH1
R4
R5
R6
R7
R9
R8
R10
R11
C50 R47
3
R46
8
BRN
BLK
BLU
IDM1
IDM MODULE
YEL
W701
1
IC1
TU1
DSP TUNER UNIT
R16
C15
5 4
1
R45
WHT
JW29
3
C54
C51
20
JW22
1
JW21
MARK
C55
IC2
RED
CN4
5 4
R50
R48
JW30
27
FB6
C52
C48
B
C56
C
C13
JW24 C6
C11
FB5
Q5
R49
G
R55
R56
FB4
C49
B
2
BLK
FB3
R13
R12
R35
E
1
JC1
JW33
FB2
JW19
9
(Page 15)
JW5
JW1
R53
C62
10
F
R28
JW2
FB1
17
JW17
18
JW28
JW27
E
2
C37
R27
JW4
C
(Page 17)
POWER
BOARD
CN301
CN1
R26
JW18
MICON
BOARD
CN401
TP3
R44
TP4
D
C27
JW15
C28
1
R59
TP2
JW9
JW14
JW10
2
CN5
E
R24
R58
1
C36
C
JW13
R15
R14
H
1-873-875-
A
• Semiconductor
Location
POWER
BOARD
W701
(Page 15)
XDR-S3HD
13
13
Ref. No.
IC1
IC2
IC3
IC4
Location
G-10
G-5
B-6
H-10
Q4
Q5
Q6
Q7
G-10
F-4
C-11
B-12
11
(11)
XDR-S3HD
3-3. SCHEMATIC DIAGRAM — MAIN SECTION — • Refer to page 20 for IC Block Diagrams.
CN1
JW31
CN2
R14
JC3
JC2
JC1
JC4
C7
C8
W701
R15
R1
R2
R51
JW33
JC5
R17
JW24
R16
TU1
C6
R19
JW1
R3
JW2
C11
C13
C15
C16
JW23
IC B/D
JW32
R59
R52
Q6
R57
R45
Q4
R58
R46
(Page 16)
JW29
IC4
C60
TH1
C59
JW14
IC1
R4
R5
R18
R6
IC B/D
R44
R7
Q7
R8
C27
S1
C28
C50
R11
C52
R10
C51
R61
R9
CN4
R47
R12
JW30
R13
JW6
R55
JW5
R56
JW4
JW7
JW19
IC3
Q5
C36
C58
C57
R48
JW21
R49
C61
IC2
C62
R37
IC B/D
R24
CN5
C37
TP2
IDM1
R53
JW11
TP1
(Page 16)
TP3
JW15
R26
C54
C56
R25
C55
TP4
R50
JW16
R27
R28
FB1
JW10
JW26
JW28
JW18
JW9
JW25
JW27
JW17
FB2
FB3
(Page 18)
FB4
FB5
JW22
FB6
C48
R35
JW13
JW12
C49
XDR-S3HD
14
14
XDR-S3HD
3-4. PRINTED WIRING BOARDS — POWER SECTION — • Refer to page 12 for Circuit Boards Location.
6
JW905
E
R138
JW907
R926
R924
R913
C
E
B
C916
R917
E
R919
C
Q910
B
R916
D908
D909
TP903
GRN
01
C9
2
BLK WITH LINE
1
W702
TP901
11
1-873-879- (11)
T901
AC POWER
UNIT
AC IN ~
JACK BOARD
C951
R180
C180
IC950
CN950
5
RED
BLK
RED
2
1
MARK
11
1-874-352- (11)
RED+
J380
i
1
C280
BLU
YEL
BLK–
R953
R954
R955
C
D901
1
C
Q951
B
E
BLU
MARK
3
C902
E
Q901
B
C
C
R903
C903
JW901
1
R950
C
Q952
R951
B
E
RED
W702
TP902
BLK
R904
FAN CNT BOARD
C950
BLK
BRN
M950
DC FAN
W703
XDR-S3HD
15
15
Ref. No.
D130
D131
D230
D231
D901
D902
D903
D904
D906
D907
D908
D909
D910
D911
D912
D913
D914
D915
D916
Location
C-3
E-3
C-3
E-3
E-9
E-9
D-9
E-8
E-8
E-7
D-11
D-11
C-10
B-10
B-9
C-7
E-7
C-8
E-7
IC301
IC302
IC901
IC902
IC903
IC950
C-5
E-5
D-7
E-7
C-8
H-6
Q130
Q131
Q230
Q231
Q331
Q332
Q901
Q902
Q903
Q904
Q905
Q906
Q907
Q908
Q909
Q910
Q911
Q912
Q913
Q914
Q915
Q951
Q952
C-4
D-3
C-4
D-4
E-6
E-6
E-9
E-9
D-9
D-8
D-9
E-8
E-6
E-6
C-11
D-10
D-10
C-9
C-7
C-9
C-9
H-5
H-4
E
D902
Q902
R905
Q903
R902
E
R906
B
B
R901
C
Q905
B
D903
E
C
C904
C910
RED
1
R918
3
MARK
R952
R920
R280
C254
Q911
B
D906
Q909
C
Q912
B
B
E
C
Q914
D910
R921
JW902
B
R912
C912
C913
D904
5
C
BLU
JW904
JW302
C153
R148
E
C909
C340
JW131
K
4
3
IC902
1
E
B
C
Q908
K A
D916
C253
I
C917
C905
E
Q906
A
E
Q331
C
R342
E
C906
K A
R914
D914
B
E
R915
C
Q907
B
JW903
D907
E
Q332
C
C339
J301
LINE IN
C918
R928
R940
R907
C
R908
Q904 R909
C148
IC901
5
C915
R911
R910
1
C156 R150
R151 R149
R248
H
B
C
C
R230
C921
C255
G
R929
5
IC903
B
E
1
Q913 JW910
K
R925
R923
A
D913
R238
C919
B
C343
C151
B
R147
R146
13
D911
JW909
R927
R339
D231
R140
JW307
C252
D131
12
D912
JW906
VIO
BRN
BLK
YEL
BLU
MARK
RED
R132
C130
C231
C232
C132
R130
C330
IC301
C131
1
C248
R143
C251
R249 C256
R250 R251
12
13
24
C331
E
Q231
B
R145
R240
IC302
1
8
W701
C907
C152
R245
C154
MARK
C134
C133
C233
1
JW130
C342
BLU
C236
C136
C150
C155
YEL
C336
C335
C
B
E
B
E
R252
Q131
C
CN303
BLK
RED
C250
C334
C230
11
• Semiconductor
Location
JW301
6
JW305
BRN
R152
1
R144
RED
JW306
SP201
SPEAKER
L-CH
C235
JW230
C
CN302
BLK
C144
R134
R247
R246
4
C240
R242
R244
R338
R142
RED
BLK
R236
R235
C140
C337 JW304
C344
R337
SP101
SPEAKER
R-CH
C244
R136
R135
C
B
1
Q130
E
2
C
F
D230
R341
D130
CN301
B
Q230
R331
MAIN
BOARD
CN4
(Page 13)
R234
10
R232
C234
C135
R133 R233
9
15
10
R334 C332
R333
9
(Page 13)
MAIN
BOARD
W701
A
R243
R336
R335
B
E
8
POWER BOARD
C333
D
7
Q915
5
E
4
WHT
A
3
D915
2
1
: Uses unleaded solder.
6
11
1-873-878- (11)
XDR-S3HD
R130
JW230
R230
C235
JW130
C233
R232
C133
R238
C132
R132
C135
J301
R138
C232
3-5. SCHEMATIC DIAGRAM — POWER SECTION — • Refer to page 20 for IC Block Diagrams.
C134
C234
CN302
SP201
IC B/D
C131
SP101
IC302
C330
C231
C230
C130
R145
C344
JW307
C248
C336
R235
R234
R236
R134
R135
R136
Q131
R335
R331
R336
R242
C153
C254
R248
R252
R250
R249
R150
JW305
C342
D231
C343
C337
R338
Q332
JW306
JW302
D230
R342
R337
C136
R334
C332
C154
R148
R149
R146
R147
R246
R247
C250
R333
C236
C331
R244
Q231
R142
D130
CN301
R243
R152
C333
JW301
R143
R240
C180
R251
C335
C256
C334
JW304
R341
R339
Q331
Q130
Q230
JW904
(Page 14)
IC B/D
Q906
Q907
Q903
D904
JW903
JW901
R906
IC901
IC B/D
R915
R913
R912
R905
R901
D901
D907
D902
R902
C903
Q902
IC902
R904
Q908
C910
R914
D906
C912
C913
C901
C909
D903
C915
R911
Q901
C905
C906
TP901
C904
R903
TP902
TP903
D914
D916
W701
R910
C907
Q904
R909
D913
R940
Q913
R908
R907
JW910
JW905
JW909
JW902
Q912
Q905
(Page 14)
JW906
Q911
D911
R921
D912
R920
R916
D908
IC B/D
D909
R917
C916
Q910
IC903
D910
R919
R927
IC950
JW907
W702
Q915
W702
CN950
M950
R955
R954
C950
R926
R924
R925
R923
R929
Q951
C951
D915
R953
R950
R928
Q914
R952
R951
Q952
XDR-S3HD
16
16
Q909
C918
C917
R918
C919
C921
IC B/D
J380
C155
C156
C244
R280
C340
C339
C240
C152
C144
R180
JW131
D131
C151
R233
R144
C252
C140
R133
C150
R140
C251
C148
R245
W703
C255
R151
IC301
CN303
C253
IC B/D
C902
T901
C280
XDR-S3HD
3-6. PRINTED WIRING BOARD — MICON SECTION — • Refer to page 12 for Circuit Boards Location.
2
1
3
4
5
6
: Uses unleaded solder.
7
8
9
10
11
12
13
MICON BOARD
C436
R525
C435
2
C422
E
B
Q404
C
C
R440
R439
R438
Q405
R437
C423
R441
B
JW412
JW407
R519
R411
R406
R521
C
Q410
E
JW410
R416
B
TP410
C414
TP412
TP409
17
E
R417
R415 C415
2 1
IC403
3 4
X401
TP416
TP408
CN401
1
TP441
X402
JW411
C402
JW421
JW405
TP417
JW408
TP413
C417
R418
C416
R409
C469
R408
C468
R407
R520
R524
JW409
E
TP415
JW404
R430
R526
C444
C409
B
1
R436
R429
R451
R450
R449
R448
R447
R446
R445
R444
R443
R432
R452
R474
R506 Q409
RED
MARK
BLU
R402
TP401
TP425
TP428
C418
R405
100 1
TP414
R505
C
JW406
JW415
D402
(LCD BACK LIGHT) JW401
R501
R503
R404
R504
R502
JW419
W704
R473
R498
R499
C457 R500
C458
JW403
R419
80
81
C456
JW420
3
31
30
IC401
R497
TP402
R420
R481
R434
R433
R426
TP405
TP404
R425
TP403
R424
R423
R496
TP418
F
TP424
R495
C455
R428
R427
R403
C403
TP419
C453
R431
51 50
R401 C401
C452
R494
1
TP426
C461
TP420
R493
C459
C460
R479
C451
TP421
H
C
R456
R522
TP427
JW418
R492
C454
G
C437
JC401
C450
JC402
E
R475
R478
R476
R477
R482
C445
RED
MARK
BLK
BRN
JW422
(Page 19)
JW416
1
R511
R510
R480
D
Q406
C
B
Q403
LCD401 LIQUID CRYSTAL DISPLAY PANEL
JW417
W705
6
E
C438
29
C
CNT
BOARD
CN306
C434
E
B
• Semiconductor
Location
1
BLU
C462
2
YEL
3
R507
B
C443
C442
C441
C440
C439
R469
R468
IC405
E
C424
C421
R470
C470
JC404 R453
C433
C432
C431
C430
C429
C428
C427
C426
C425
C419 C420
A
TP423
TP440
TP411
TP422
D401
(LCD BACK LIGHT)
R435
TP407
TP406
18
JW413
1-873-882-
I
D
C
CNT
BOARD
CN305
MAIN
BOARD
CN5
(Page 19)
(Page 13)
XDR-S3HD
17
17
11
(11)
Ref. No.
D401
D402
Location
G-12
G-3
IC401
IC403
IC405
D-9
F-11
A-3
Q403
Q404
Q405
Q406
Q409
Q410
A-10
C-12
C-12
A-9
F-6
E-11
XDR-S3HD
3-7. SCHEMATIC DIAGRAM — MICON SECTION — • Refer to page 12 for Waveforms, page 21 for IC Block Diagrams and page 22 for IC Pin Description.
W705
R479
LCD401
R480
R510
R511
(Page 20)
C438
C437
C436
C434
R522
R456
R468
R469
R482
JC402
C445
R452
R470
JC404
C425
C428
C427
C426
C430
C429
C433
C432
C431
R443
R445
R444
R448
R447
R446
R451
R449
R453
R450
R476
R475
R481
R478
R477
Q406
R474
C424
CN401
TP407
JW409
TP406
C420
Q403
R432
C450
C451
C452
R494
C453
R495
C454
R496
R428
C455
R497
R427
C456
R498
C457
R499
R431
R493
R430
R429
TP426
TP423
TP422
TP421
TP420
JW406
TP419
TP418
TP417
C458
C422
R500
R526
TP414
TP413
C459
R501
C460
R503
TP412
R506
JW405
TP411
TP410
R426
R505
C461
R425
R424
TP409
R423
TP408
JW408
R436
JW412
R502
TP415
C423 TP428
TP425
IC401
R504
TP416
(Page 14)
C421
R492
JW415
TP441
C419
JC401
TP424
D401
R417
R437
TP405
TP404
R435
D402
R438 R439
R434
R441
TP403
TP402
R433
Q409
W704
Q404
JW419
JW403
C416
R507
X402
JW422
X401
JW420
C401
TP440
JW421
R521
R411
R415
C468
R404
C402
C403
R416
JW411
IC B/D
Q410
R519
C414
JW407
R524
C415
R520
XDR-S3HD
18
18
R419
R418
R403
C462
R420
R409
R405 C409
JW401
JW413
R408
IC405
R407
R402
R401
R406
TP401
JW404
(Page 20)
IC403
C469
C417
C418
R440
Q405
C443
C440
C439
C470
C441
R525
C435
TP427
R473
C442
C444
JW417
JW416
XDR-S3HD
3-8. PRINTED WIRING BOARDS — KEY SECTION — • Refer to page 12 for Circuit Boards Location.
2
1
4
5
6
S806
ENTER
S805
MENU
S807
DISPLAY
S805
S807
S808
S806
R810
R808
R807
R809
A
3
: Uses unleaded solder.
7
S808
TONE
R806
8
9
S809
PRESET
S804
RADIO/LINE IN
S809
S804
10
R801
3
11
12
S803
BAND
S802
SLEEP
S803
S802
R802
13
14
S801
POWER
S801
1
R805
R804
BLU
MARK
RED
RED
KEY BOARD
MARK
B
BLU
W706
11
1-873-876- (11)
(Page 17)
MICON
BOARD
W704
C
RED
CN305
MARK
BLU
JC830
BLU
1
JC834
JC832
11
1-873-877- (11)
JW834
CN306
6
1
11
G
BLK
BRN
YEL
BLU
MARK
RED
1-873-880-
CNT BOARD
E
MICON
BOARD
W705
(Page 17)
H
XDR-S3HD
19
S813
VOLUME
11
1-873-881- (11)
F
33
2
JC835
3
W708
1
R833
BLU
1
6
CN304
2
R831
MARK
RED
RED
MARK
BLU
1
6
R832
RED
MARK
13
S812
TUNE/SELECT
E
W707
1
VOL BOARD
JC831
R830
D
BLU
TUNE BOARD
MARK
RED
D
19
(11)
XDR-S3HD
3-9. SCHEMATIC DIAGRAM — KEY SECTION —
• IC Block Diagrams
S804
S803
R802
S802
R804 R805
EXT
R801
IC4 XC6213B332MR (MAIN BOARD)
CE
IC1 XC62EP1802MR (MAIN BOARD)
IC2 XC62EP1802MR (MAIN BOARD)
5
4
VIN 1
ON/OFF
CONTROL
S801
W706
R806
R807
R808
5 VOUT
4 NC
PROTECTION
R809 R810
S806
S805
CN305
1
2
3
VOUT
S807
VIN
S808
VSS
S809
+
–
CURRENT
LIMIT
VREF
VSS 2
CE 3
S812
W707 R830
(Page 18)
CN304
CN306
JC835
R831
IC301 BD3870FS-E2 (POWER BOARD)
JC832
JW834
JC831
TNF1
TNF2
BNF2
BOUT2
BNF1
BOUT1
OUT1
OUT2
VCC
SI
SC
W708 R832
CAP
JC834
24
23
22
21
20
19
18
17
16
15
14
13
SURROUND
JC830
(Page 18)
TREBLE1
f0=8kHz
TREBLE2
f0=8kHz
R833
S813
BASS2
f0=80Hz
BASS1
f0=80Hz
LOGIC
VCC/2
VCC/2
VCC/2
9
10
11 12
FILTER
IC302 BA5417 (POWER BOARD)
T.S.D.
+
–
+
–
STANDBY
BS
XDR-S3HD
20
20
FILTER
2
3 4 5
6
7
8
9
10
11 12
13
14 15
NC
OUT2
VCC
OUT1
BS1
POWER GND
STBY
FILTER
NF1
IN1
NF2
PRE GND1
PRE GND2
IN2
1
BS2
BS
GND
8
C2
7
C1
6
B2
5
B1
4
A2
VIN2
3
A1
2
SEL1
1
SEL2
VCC/2
VIN1
VCC/2
VOLTAGE
REFERENCE
XDR-S3HD
IC901 NJM2387ADL3(TE2) (POWER BOARD)
IC903 NJM2387ADL3(TE2) (POWER BOARD)
IC950 NJM2387ADL3(TE2) (FAN CNT BOARD)
CURRENT
LIMIT
OVERVOLTAGE
PROTECTION
THERMAL
PROTECTION
BANDGAP
REFERENCE
1
2
3
4
5
VIN
CONTROL
VOUT
VADJ
GND
VIN
VOUT
IC902 NJM2871BF33-TE2 (POWER BOARD)
5
4
THERMAL
PROTECTION
BANDGAP
REFERENCE
3
GND
NOISE
BYPASS
2
CONTROL
1
VSS
NC
IC403 XC61CN2702NR (MICON BOARD)
4
3
1
2
VOUT
VIN
VREF
21
XDR-S3HD
• IC Pin Description
IC401 M3062LFGPFP (SYSTEM CONTROL) (MICON BOARD)
Pin No.
Pin Name
I/O
1
2
P9_6/NC
P9_5/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
3
4
P9_4/RMT
P9_3/NC
I
O
Remote commander signal input
Fixed at L level (Not used)
5
6
P9_2/NC
P9_1/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
7
8
P9_0/NC
BYTE
O
I
Fixed at L level (Not used)
Not used. (Connect to VSS)
9
10
CNVSS
XCIN
I
I
Not used. (Fixed at L level)
System sub clock signal input (32 kHz)
11
12
XCOUT
RESET
O
I
System sub clock signal output (32 kHz)
Micon reset input (L: Micon reset)
13
14
XOUT
VSS
O
—
System main clock signal output (5.53 MHz)
Ground
15
16
XIN
VCC1
I
—
System main clock signal input (5.53 MHz)
Power supply pin (+3.3 V)
17
18
NMI
INT2/VDET
I
I
NMI interruption signal input (Fixed at H level)
Power failure detection signal input (H: backup mode)
19
20
INT1/DTUNER_RDS
INT0/NC
I
I
RDS data interruption signal input (Not used)
Not used. (Open)
21
22
P8_1/CLOCK SHIFT
P8_0/NC
O
O
Control pin for system main clock frequency shift. (H: active)
Fixed at L level (Not used)
23
24
P7_7/NC
P7_6/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
25
26
P7_5/NC
P7_4/ATUNER_CLK
O
O
Fixed at L level (Not used)
Analog tuner clock signal output (Not used)
27
28
P7_3/ATUNER_DI
P7_2/TA10OUT/BEEP
O
O
Analog tuner data output (Not used)
Beep signal output
29
30
RXD2/DTUNER_SCL
TXD2/DTUNER_SDA
—
—
Communication pin for digital tuner.
Communication pin for digital tuner.
31
32
P6_7/SDA
P6_6/SCL1
O
O
Flash write pin (Normally: output port)
Flash write pin (Normally: output port)
33
34
P6_5/CLK1
P6_4/CTS0
O
O
Flash write pin (Normally: output port)
Flash write pin (Normally: output port)
35
36
P6_3/NC
P6_2/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
37
38
P6_1/NC
P6_0/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
39
40
P5_7/NC
P5_6/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
41
42
P5_5/EPM
P5_4/NC
O
O
Flash write pin (Normally: output port)
Fixed at L level (Not used)
43
44
P5_3/NC
P5_2/LIGHT2
O
O
Fixed at L level (Not used)
LCD back light control signal output
45
46
P5_1/LIGHT1
P5_0/CE
O
O
LCD back light control signal output
Flash write pin (Normally: output port)
47
48
P4_7/CSB
P4_6/RST
O
O
LCD driver control signal output
LCD driver reset signal output (H: driver reset)
49
50
P4_5/A0
P4_4/WRB
O
O
LCD driver control signal output
LCD driver control signal output
51
P4_3/RDB
O
LCD driver control signal output
22
Pin Description
XDR-S3HD
Pin No.
52
Pin Name
P4_2/NC
I/O
O
Fixed at L level (Not used)
53
54
P4_1/NC
P4_0/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
55
56
P3_7/D0
P3_6/D1
O
O
LCD data output
LCD data output
57
58
P3_5/D2
P3_4/D3
O
O
LCD data output
LCD data output
59
60
P3_3/D4
P3_2/D5
O
O
LCD data output
LCD data output
61
62
P3_1/D6
VCC2
O
—
LCD data output
Power supply pin (+3.3 V)
63
64
P3_0/D7
VSS
O
—
LCD data output
Ground
65
66
P2_7/AN2_7/SHIMUKE2
P2_6/AN2_6/SHIMUKE1
I
I
Destination select signal input (Fixed at L level)
Destination select signal input (Fixed at L level)
67
68
P2_5/AN2_5/NC
P2_4/AN2_4/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
69
70
P2_3/AN2_3/NC
P2_2/AN2_2/NC
O
O
Fixed at L level (Not used)
Fixed at L level (Not used)
71
72
P2_1/AN2_1/ENC2_DATA
P2_0/AN2_0/ENC1_DATA
I
I
Rotary encoder (VOLUME) data input
Rotary encoder (TUNE/SELECT) data input
73
74
P1_7/INT5/ENC1_CLK
P1_6/INT4/ENC2_CLK
I
I
Rotary encoder (TUNE/SELECT) clock signal input
Rotary encoder (VOLUME) clock signal input
75
76
77
P1_5/INT3/KEY_IN
P1_4/NC
P1_3/KEY_LED
I
O
O
Valid key interruption signal input at power off (Fixed at L level).
Fixed at L level (Not used)
Key LED control signal output (Not used)
78
79
P1_2/NC
P1_1/E2PROM_SCL
O
O
Fixed at L level (Not used)
E2PROM clock signal output (Not used)
80
81
P1_0/E2PROM_SDA
P0_7/AN0_7/VOL_CLK
I/O
O
E2PROM data output (Not used)
Clock signal output for sound IC communication.
82
P0_6/AN0_6/VOL_DATA
P0_5/AN0_5/AUDIO_
O
Data output for sound IC communication.
O
Audio mute detection signal output (H: mute ON)
O
Audio standby detection signal output (H: power ON)
I
Analog tuner DO signal input (Not used)
O
DSP tuner/DSP reset signal output (L: reset)
O
DSP tuner power control signal output (L: radio function)
O
Analog tuner chip enable signal output (Not used)
I
DSP tuner blend signal input (H: HD digital audio)
83
84
85
86
87
88
89
90
MUTE
P0_4/AN0_4/AUDIO_
STANDBY
P0_3/AN0_3/ATUNER_
DO
P0_2/AN0_2/DTUNER_
RESET
P0_1/AN0_1/DTUNER_
POWER
P0_0/AN0_0/ATUNER_
CE
P10_7/AN7/DTUNER_
BLEND
P10_6/AN6/AM(AM/FM)
Pin Description
O
Radio (AM) receive signal output (H: AM)
91
P10_5/AN5/NON HD
(HD/NON HD)
O
Radio (HD) receive signal output (H: HD)
92
93
P10_4/AN4/HD
P10_3/AN3/FM
O
O
Radio (HD) receive signal output (L: HD) (Not used)
Radio (FM) receive signal output (H: FM) (Not used)
94
95
P10_2/AN2/KEY1
P10_1/AN1/KEY2
I
I
A/D converter analog signal input
A/D converter analog signal input
96
AVSS
—
Ground for A/D converter.
23
XDR-S3HD
Pin No.
Pin Name
I/O
97
P10_0/KEY OFF
O
24
Pin Description
A/D key, remote control receiver and rotary encoder power control signal
98
VREF
—
output. (L: normally, H: backup)
Reference voltage input for A/D converter. (+3.3 V)
99
100
AVCC
P9_7/NC
—
O
Power supply pin for A/D converter. (+3.3 V)
Fixed at L level (Not used)
XDR-S3HD
SECTION 4
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
• Accessory and parts list are given in the last of
this parts list.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
4-1. MAIN SECTION
#1
#1
#1
cabinet section
#1
front panel section
not supplied
not supplied
1
Ref. No.
1
Part No.
Description
X-2177-965-1 NET SUB ASSY, SPEAKER
Remark
Ref. No.
#1
Part No.
Description
Remark
7-621-849-10 SCREW, WOOD +R 3.1X13
25
XDR-S3HD
4-2. FRONT PANEL SECTION
57
58
56
55
59
54
53
LCD401
52
not supplied
52
51
Ref. No.
51
52
53
54
55
26
Part No.
Description
X-2179-523-1
2-667-343-01
3-100-681-01
3-100-680-01
3-100-679-01
PANEL (FRONT) SUB ASSY
BUSHING
SHEET (LCD), DIFFUSION
PLATE (LCD), LIGHT GUIDE
REFLECTOR (LCD)
Remark
Ref. No.
56
57
58
59
LCD401
Part No.
Description
3-100-678-01
X-2179-670-1
1-834-138-21
3-252-827-01
1-802-474-11
HOLDER (LCD)
MICON BOARD, COMPLETE
CABLE, FLEXIBLE FLAT (18 CORE)
SCREW (B2.6), (+) BV TAPPING
DISPLAY PANEL, LIQUID CRYSTAL
Remark
XDR-S3HD
4-3. KEY BOARD SECTION
106
107
105
108
101
102
102
103
101
109
102
104
110
not supplied
103
111
102
102
112
102
not supplied
SP201
#2
#2
#2
cabinet section
SP101
#2
Ref. No.
Part No.
Description
101
102
103
104
105
3-100-675-01
3-254-081-11
3-100-674-01
A-1257-298-A
3-100-672-01
KNOB (JOG)
SCREW
ESCUTCHEON
VOL BOARD, COMPLETE
BUTTON (POWER)
106
107
108
3-100-673-01 BUTTON (MENU)
3-106-282-01 BUTTON (TONE)
3-106-281-01 BUTTON (ENTER)
Remark
Ref. No.
Part No.
Description
109
110
111
112
SP101
3-100-694-01
3-100-671-01
A-1257-296-A
A-1257-300-A
1-826-688-11
SPRING (BUTTON)
PANEL (TOP, KEY)
KEY BOARD, COMPLETE
TUNE BOARD, COMPLETE
SPEAKER (6.6cm) (R-CH)
SP201
#2
1-826-688-11 SPEAKER (6.6cm) (L-CH)
7-621-843-25 SCREW, WOOD +R 3.1X10
Remark
27
XDR-S3HD
4-4. CABINET SECTION
not supplied
151
153
154
152
T901
not supplied
chassis section
155
156
160
155
156
159
157
M950
157
A
A
158
159
159
154
154
Ref. No.
Part No.
Description
151
152
153
154
155
X-2177-282-1
3-218-790-01
3-100-682-01
3-254-143-11
3-100-687-01
CABINET ASSY
CUSHION (REAR COVER)
COVER (REAR)
SCREW (B3), (+) BV TAPPING
SHEET (FOOT), ADHESIVE
156
3-100-683-01 FOOT
28
Remark
Ref. No.
157
158
159
160
M950
0 T901
Part No.
Description
2-667-344-01
3-214-708-01
3-254-145-11
3-252-827-01
1-787-396-11
FOOT, RUBBER
COVER (FAN)
SCREW (B3), (+) BV TAPPING
SCREW (B2.6), (+) BV TAPPING
FAN, D.C. (50 SQUARE)
1-480-224-11 POWER UNIT, AC
Remark
XDR-S3HD
4-5. CHASSIS SECTION
203
203
204
205
TU1
203
207
CN2
201
202
IDM1
206
203
208
215
203
210
not supplied
(CNT board)
209
210
211
214
212
not supplied
(FAN CNT board)
213
Ref. No.
Part No.
Description
Part No.
Description
201
202
203
* 204
205
3-197-151-01
3-197-151-11
3-254-143-11
A-1257-209-A
3-198-658-01
CASE (LID), SHIELD
CASE (LID), SHIELD
SCREW (B3), (+) BV TAPPING
MAIN BOARD, COMPLETE
COVER (DSP01, A)
Remark
Ref. No.
211
212
213
214
215
A-1257-291-A
3-100-676-01
3-253-143-01
1-834-139-21
3-100-677-01
POWER BOARD, COMPLETE
CHASSIS (LOWER)
SCREW (B2.6), (+) P TAPPING
CABLE, FLEXIBLE FLAT (10 CORE)
CHASSIS (UPPER)
206
207
208
209
210
3-198-659-01
2-667-338-01
2-667-342-01
A-1257-294-A
3-252-827-01
COVER (DSP01, B)
NUT (ANTENNA)
LUG
JACK BOARD, COMPLETE
SCREW (B2.6), (+) BV TAPPING
CN2
1-817-371-21 CONNECTOR, COAXIAL (F TYPE)
(ANTENNA (FM))
A-1256-714-A IDM MODULE
A-1256-754-A TUNER UNIT, DSP
IDM1
TU1
Remark
29
XDR-S3HD
CNT
FAN CNT
JACK
SECTION 5
ELECTRICAL PARTS LIST
KEY
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC..: µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
Description
Remark
Ref. No.
CNT BOARD
**********
Part No.
When indicating parts by reference
number, please include the board.
Description
Remark
A-1257-294-A JACK BOARD, COMPLETE
*********************
< CONNECTOR >
CN304
CN305
CN306
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
< CAPACITOR >
1-568-272-11 SOCKET, CONNECTOR 6P
1-568-272-11 SOCKET, CONNECTOR 6P
1-568-272-11 SOCKET, CONNECTOR 6P
C180
C280
1-162-966-11 CERAMIC CHIP
1-162-966-11 CERAMIC CHIP
0.0022uF 10%
0.0022uF 10%
50V
50V
< JACK >
< JUMPER RESISTOR >
J380
JC830 1-216-864-11 SHORT CHIP
0
JC831 1-216-864-11 SHORT CHIP
0
JC832 1-216-864-11 SHORT CHIP
0
JC834 1-216-864-11 SHORT CHIP
0
JC835 1-216-864-11 SHORT CHIP
0
*************************************************************
1-819-829-11 JACK (HEADPHONE)
< RESISTOR >
R180
1-216-809-11 METAL CHIP
100
5%
1/10W
R280
1-216-809-11 METAL CHIP
100
5%
1/10W
*************************************************************
FAN CNT BOARD
**************
A-1257-296-A KEY BOARD, COMPLETE
********************
< CAPACITOR >
C950
C951
1-115-156-11 CERAMIC CHIP
1-124-261-00 ELECT
< RESISTOR >
1uF
10uF
20%
10V
10V
< CONNECTOR >
CN950
1-216-833-11
1-216-833-11
1-216-829-11
1-216-825-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
4.7K
2.2K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R807
R808
R809
R810
1-216-833-11
1-216-833-11
1-216-829-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
4.7K
2.2K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P
< IC >
IC950
R801
R802
R804
R805
R806
6-709-213-01 IC NJM2387ADL3(TE2)
< SWITCH >
< TRANSISTOR >
Q951
Q952
S801
S802
S803
S804
S805
6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF
8-729-027-44 TRANSISTOR DTC114TKA-T146
< RESISTOR >
R950
R951
R952
R953
R954
1-216-841-11
1-216-841-11
1-216-821-11
1-216-829-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
1K
4.7K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R955
1-216-821-11 METAL CHIP
1K
5%
1/10W
*************************************************************
30
1-786-958-11
1-786-958-11
1-786-958-11
1-786-958-11
1-786-958-11
SWITCH, TACTILE (POWER)
SWITCH, TACTILE (SLEEP)
SWITCH, TACTILE (BAND)
SWITCH, TACTILE (RADIO/LINE IN)
SWITCH, TACTILE (MENU)
S806
1-786-958-11 SWITCH, TACTILE (ENTER)
S807
1-786-958-11 SWITCH, TACTILE (DISPLAY)
S808
1-786-958-11 SWITCH, TACTILE (TONE)
S809
1-786-958-11 SWITCH, TACTILE (PRESET)
*************************************************************
XDR-S3HD
MAIN
Ref. No.
Part No.
*
A-1257-209-A MAIN BOARD, COMPLETE
*********************
Description
Remark
C6
C7
C8
C11
C13
1-162-970-11
1-162-970-11
1-126-947-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
47uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
25V
25V
35V
25V
25V
C15
C16
C27
C28
C36
1-162-970-11
1-126-947-11
1-164-315-11
1-164-315-11
1-162-970-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47uF
470PF
470PF
0.01uF
10%
20%
5%
5%
10%
25V
35V
50V
50V
25V
C37
C48
C49
C50
C51
1-162-970-11
1-162-970-11
1-126-935-11
1-162-970-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.01uF
0.01uF
470uF
0.01uF
10uF
10%
10%
20%
10%
20%
25V
25V
16V
25V
50V
C52
C54
C55
C56
C57
1-162-970-11
1-162-970-11
1-126-935-11
1-162-970-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
470uF
0.01uF
1uF
10%
10%
20%
10%
25V
25V
16V
25V
10V
C58
C59
C60
C61
C62
1-126-947-11
1-115-156-11
1-126-964-11
1-126-168-11
1-162-970-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
47uF
1uF
10uF
1000uF
0.01uF
20%
20%
20%
10%
35V
10V
50V
6.3V
25V
< TERMINAL BOARD >
1-780-519-11 TERMINAL BOARD (2P) (ANTENNA (AM))
< CONNECTOR >
CN4
CN5
Part No.
Description
Remark
< TRANSISTOR >
< CAPACITOR >
CN1
Ref. No.
1-784-732-11 CONNECTOR, FFC 10P
1-779-555-21 CONNECTOR, FFC (LIF(NON-ZIF)) 18P
Q4
Q5
Q6
Q7
8-729-034-00
8-729-024-93
6-551-700-01
8-729-029-14
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1282ATP-EF
2SB1565E
ISA1602AM1TP-1F
DTC144EUA-T106
< RESISTOR >
R1
R2
R3
R4
R5
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R6
R7
R8
R9
R10
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R11
R12
R13
R14
R15
1-216-864-11
1-216-864-11
1-216-821-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
0
1K
0
0
R16
R17
R18
R19
R24
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-11
1-216-821-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
0
0
0
1K
1K
R25
R26
R27
R28
R35
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R37
R44
R45
R46
R47
1-216-864-11
1-216-864-11
1-216-841-11
1-216-813-11
1-216-841-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
47K
220
47K
R48
R49
R50
R51
R52
1-216-841-11
1-216-864-11
1-216-841-11
1-216-825-11
1-216-825-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R53
R55
R56
R57
R58
1-216-833-11
1-216-817-11
1-216-817-11
1-216-837-11
1-216-845-11
R59
R61
5%
1/10W
5%
5%
1/10W
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
47K
0
47K
2.2K
2.2K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470
470
22K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-829-11 METAL CHIP
1-216-829-11 METAL CHIP
4.7K
4.7K
5%
5%
1/10W
1/10W
< FERRITE BEAD >
FB1
FB2
FB3
FB4
FB5
1-414-227-11
1-414-227-11
1-414-227-11
1-414-227-11
1-414-227-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB6
1-414-227-11 INDUCTOR, FERRITE BEAD
< IC >
IC1
IC2
IC3
IC4
6-701-114-01
6-701-114-01
6-707-747-01
6-710-962-01
IC
IC
IC
IC
XC62EP1802MR
XC62EP1802MR
XC6203P332PR
XC6213B332MR
< SWITCH >
< JUMPER RESISTOR >
S1
JC1
JC2
JC3
JC4
JC5
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
1-554-088-00 SWITCH, KEYBOARD (RESET)
< THERMISTOR >
TH1
1-805-074-11 THERMISTOR
*************************************************************
31
XDR-S3HD
MICON
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
X-2179-670-1 MICON BOARD, COMPLETE
**********************
Description
Remark
< CONNECTOR >
CN401
1-779-555-21 CONNECTOR, FFC (LIF(NON-ZIF)) 18P
< CAPACITOR >
< DIODE >
C401
C402
C403
C409
C414
1-162-927-11
1-162-919-11
1-162-919-11
1-115-156-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
22PF
22PF
1uF
0.01uF
5%
5%
5%
C415
C416
C417
C418
C419
1-107-826-11
1-164-156-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
100PF
100PF
100PF
10%
C420
C421
C422
C423
C424
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C425
C426
C427
C428
C429
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
C430
C431
C432
C433
C434
10%
50V
50V
50V
10V
25V
D401
D402
6-501-880-01 LED SDPW31G0C0000 (LCD BACK LIGHT)
6-501-880-01 LED SDPW31G0C0000 (LCD BACK LIGHT)
< IC >
5%
5%
5%
16V
25V
50V
50V
50V
✩ IC401
IC403
IC405
100PF
100PF
100PF
100PF
0.01uF
5%
5%
5%
5%
10%
50V
50V
50V
50V
25V
JC401
JC402
JC404
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
LCD401 1-802-474-11 DISPLAY PANEL, LIQUID CRYSTAL
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
1uF
5%
5%
5%
5%
50V
50V
50V
50V
10V
C435
C436
C437
C438
C439
1-164-346-11
1-164-346-11
1-164-346-11
1-164-346-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
1uF
1uF
1uF
16V
16V
16V
16V
10V
C440
C441
C442
C443
C444
1-115-156-11
1-115-156-11
1-115-156-11
1-164-346-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
1uF
1uF
1uF
10V
10V
10V
16V
10V
C445
C450
C451
C452
C453
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C454
C455
C456
C457
C458
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C459
C460
C461
C462
C468
1-162-964-11
1-162-964-11
1-107-826-11
1-162-970-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.1uF
0.01uF
100PF
10%
10%
10%
10%
5%
50V
50V
16V
25V
50V
C469
C470
1-162-927-11 CERAMIC CHIP
1-115-156-11 CERAMIC CHIP
100PF
1uF
5%
50V
10V
(not supplied) IC M3062LFGPFP
6-702-148-01 IC XC61CN2702NR
6-600-349-31 IC NJL24H400A (IR)
< JUMPER RESISTOR >
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
0
< LIQUID CRYSTAL DISPLAY >
< TRANSISTOR >
Q403
Q404
Q405
Q406
Q409
6-551-696-01
8-729-620-07
8-729-620-07
8-729-027-44
6-551-696-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
ISA1235AC1TP-1EF
2SC3052EF-T1-LEF
2SC3052EF-T1-LEF
DTC114TKA-T146
ISA1235AC1TP-1EF
Q410
8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
< RESISTOR >
R401
R402
R403
R404
R405
1-216-821-11
1-216-833-11
1-216-849-11
1-216-821-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
1K
10K
220K
1K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R406
R407
R408
R409
R411
1-216-833-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1K
1K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R415
R416
R417
R418
R419
1-216-833-11
1-216-853-11
1-216-841-11
1-216-841-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470K
47K
47K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R420
R423
R424
R425
R426
1-216-809-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R427
R428
R429
R430
R431
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R432
R433
1-216-821-11 METAL CHIP
1-216-833-11 METAL CHIP
1K
10K
5%
5%
1/10W
1/10W
✩ IC401 on the MICON board cannot be replaced as a single component.
When IC401 is faulty, replace the IC together with the board by a new
IC complete MICON board (X-2179-670-1).
32
XDR-S3HD
MICON
Ref. No.
Part No.
Description
R434
R435
R436
R437
R438
1-216-833-11
1-216-797-11
1-216-797-11
1-216-813-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10
10
220
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R439
R440
R441
R443
R444
1-216-813-11
1-216-805-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
47
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R445
R446
R447
R448
R449
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R450
R451
R452
R453
R456
1-216-821-11
1-216-821-11
1-216-797-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R468
R469
R470
R473
R474
1-216-857-11
1-216-845-11
1-216-849-11
1-216-853-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
100K
220K
470K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R475
R476
R477
R478
R479
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R480
R481
R482
R492
R493
1-216-845-11
1-216-821-11
1-216-845-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
100K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R494
R495
R496
R497
R498
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R499
R500
R501
R502
R503
1-216-821-11
1-216-821-11
1-216-821-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
47K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R504
R505
R506
R507
R510
1-216-841-11
1-216-837-11
1-216-797-11
1-216-797-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
22K
10
10
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R511
R519
R520
R521
R522
1-216-845-11
1-216-829-11
1-216-829-11
1-216-845-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
4.7K
4.7K
100K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R524
R525
R526
1-216-821-11 METAL CHIP
1-216-853-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
470K
1K
5%
5%
5%
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
POWER
Remark
< VIBRATOR >
X401
1-813-202-11 VIBRATOR, CRYSTAL (32kHz)
X402
1-813-988-21 VIBRATOR, CERAMIC (5.53MHz)
*************************************************************
A-1257-291-A POWER BOARD, COMPLETE
***********************
3-253-143-01 SCREW (B2.6), (+) P TAPPING
< CAPACITOR >
C130
C131
C132
C133
C134
1-126-963-11
1-126-963-11
1-162-964-11
1-162-964-11
1-126-963-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
4.7uF
4.7uF
0.001uF
0.001uF
4.7uF
20%
20%
10%
10%
20%
50V
50V
50V
50V
50V
C135
C136
C140
C144
C148
1-162-927-11
1-162-966-11
1-127-715-11
1-127-715-11
1-126-963-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
0.0022uF
0.22uF
0.22uF
4.7uF
5%
10%
10%
10%
20%
50V
50V
16V
16V
50V
C150
C151
C152
C153
C154
1-126-963-11
1-126-947-11
1-162-927-11
1-126-933-11
1-107-826-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
4.7uF
47uF
100PF
100uF
0.1uF
20%
20%
5%
20%
10%
50V
35V
50V
16V
16V
C155
C156
C230
C231
C232
1-126-767-11
1-127-715-11
1-126-963-11
1-126-963-11
1-162-964-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
1000uF
0.22uF
4.7uF
4.7uF
0.001uF
20%
10%
20%
20%
10%
16V
16V
50V
50V
50V
C233
C234
C235
C236
C240
1-162-964-11
1-126-963-11
1-162-927-11
1-162-966-11
1-127-715-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
4.7uF
100PF
0.0022uF
0.22uF
10%
20%
5%
10%
10%
50V
50V
50V
50V
16V
C244
C248
C250
C251
C252
1-127-715-11
1-126-963-11
1-126-963-11
1-126-947-11
1-162-927-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.22uF
4.7uF
4.7uF
47uF
100PF
10%
20%
20%
20%
5%
16V
50V
50V
35V
50V
C253
C254
C255
C256
C330
1-126-933-11
1-107-826-11
1-126-767-11
1-127-715-11
1-126-947-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
100uF
0.1uF
1000uF
0.22uF
47uF
20%
10%
20%
10%
20%
16V
16V
16V
16V
35V
C331
C332
C333
C334
C335
1-126-959-11
1-126-960-11
1-104-665-11
1-107-826-11
1-162-927-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.47uF
1uF
100uF
0.1uF
100PF
20%
20%
20%
10%
5%
50V
50V
25V
16V
50V
C336
C337
C339
C340
C342
1-162-927-11
1-126-947-11
1-126-947-11
1-107-826-11
1-126-964-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
100PF
47uF
47uF
0.1uF
10uF
5%
20%
20%
10%
20%
50V
35V
35V
16V
50V
C343
C344
1-126-964-11 ELECT
1-162-964-11 CERAMIC CHIP
10uF
0.001uF
20%
10%
50V
50V
33
XDR-S3HD
POWER
Ref. No.
Part No.
Description
Part No.
Description
C901
C902
C903
C904
C905
1-107-892-11
1-126-927-11
1-162-970-11
1-162-970-11
1-126-935-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
4700uF
2200uF
0.01uF
0.01uF
470uF
20%
20%
10%
10%
20%
25V
10V
25V
25V
16V
Remark
Ref. No.
Q231
Q331
Q332
Q901
Q902
8-729-620-07
8-729-027-44
6-551-696-01
8-729-620-07
6-551-696-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3052EF-T1-LEF
DTC114TKA-T146
ISA1235AC1TP-1EF
2SC3052EF-T1-LEF
ISA1235AC1TP-1EF
Remark
C906
C907
C909
C910
C912
1-115-156-11
1-128-551-11
1-162-970-11
1-126-933-11
1-164-156-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
22uF
0.01uF
100uF
0.1uF
20%
10%
20%
10V
63V
25V
16V
25V
Q903
Q904
Q905
Q906
Q907
8-729-018-99
6-551-696-01
8-729-027-44
8-729-011-92
6-551-696-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2394-F
ISA1235AC1TP-1EF
DTC114TKA-T146
2SC2001TP-K1K2
ISA1235AC1TP-1EF
C913
C915
C916
C917
C918
1-165-176-11
1-126-918-11
1-162-970-11
1-162-970-11
1-126-935-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.047uF
4700uF
0.01uF
0.01uF
470uF
10%
20%
10%
10%
20%
16V
6.3V
25V
25V
16V
Q908
Q909
Q910
Q911
Q912
8-729-027-44
8-729-620-07
6-551-696-01
8-729-018-99
8-729-027-44
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114TKA-T146
2SC3052EF-T1-LEF
ISA1235AC1TP-1EF
2SD2394-F
DTC114TKA-T146
C919
C921
1-115-156-11 CERAMIC CHIP
1-104-655-11 ELECT
1uF
470uF
20%
10V
6.3V
Q913
Q914
Q915
8-729-027-38 TRANSISTOR DTA144EKA-T146
8-729-027-44 TRANSISTOR DTC114TKA-T146
6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF
< CONNECTOR >
< RESISTOR >
CN301
CN302
CN303
1-784-732-11 CONNECTOR, FFC 10P
1-568-270-11 SOCKET, CONNECTOR 4P
1-568-272-11 SOCKET, CONNECTOR 6P
R130
R132
R133
R134
R135
1-216-821-11
1-216-829-11
1-216-853-11
1-216-849-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
4.7K
470K
220K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R136
R138
R140
R142
R143
1-216-829-11
1-216-841-11
1-216-829-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
4.7K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R144
R145
R146
R147
R148
1-216-821-11
1-216-833-11
1-216-817-11
1-216-813-11
1-216-789-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
470
220
2.2
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R149
R150
R151
R152
R230
1-216-837-11
1-216-841-11
1-216-833-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
47K
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< IC >
R232
R233
R234
R235
R236
1-216-829-11
1-216-853-11
1-216-849-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
470K
220K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC
IC
IC
IC
IC
R238
R240
R242
R243
R244
1-216-841-11
1-216-829-11
1-216-821-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
4.7K
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< TRANSISTOR >
R245
R246
R247
R248
R249
1-216-833-11
1-216-817-11
1-216-813-11
1-216-789-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470
220
2.2
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
R250
R251
R252
1-216-841-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-821-11 METAL CHIP
47K
10K
1K
5%
5%
5%
1/10W
1/10W
1/10W
< DIODE >
D130
D131
D230
D231
D901
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
D902
D903
D904
D906
D907
8-719-991-33
8-719-110-17
8-719-991-33
8-719-109-89
8-719-069-29
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
RD10ESB2
1SS133T-77
RD5.6ESB2
RB520S-30TE61
D908
D909
D910
D911
D912
8-719-991-33
8-719-991-33
8-719-921-40
8-719-991-33
8-719-046-47
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
MTZJ-4.7C
1SS133T-77
1N5401TM
D913
D914
D915
D916
8-719-988-61
8-719-069-29
8-719-991-33
8-719-988-61
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
RB520S-30TE61
1SS133T-77
1SS355TE-17
IC301
IC302
IC901
IC902
IC903
6-701-824-11
8-759-426-51
6-709-213-01
6-708-637-01
6-709-213-01
BD3870FS-E2
BA5417
NJM2387ADL3(TE2)
NJM2871BF33-TE2
NJM2387ADL3(TE2)
< JACK >
J301
Q130
Q131
Q230
34
1-563-857-31 JACK, HEADPHONE (LINE IN)
XDR-S3HD
POWER
Ref. No.
Part No.
Description
R331
R333
R334
R335
R336
1-216-829-11
1-216-841-11
1-216-853-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
470K
1K
1K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R337
R338
R339
R341
R342
1-216-821-11
1-216-853-11
1-216-841-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
470K
47K
1K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
R902
R903
R904
R905
1-216-833-11
1-216-829-11
1-216-829-11
1-216-833-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
4.7K
4.7K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R909
R910
1-216-809-11
1-216-841-11
1-216-821-11
1-216-829-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
47K
1K
4.7K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
R912
R913
R914
R915
1-216-821-11
1-216-821-11
1-216-821-11
1-216-841-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
47K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R916
R917
R918
R919
R920
1-216-833-11
1-216-829-11
1-216-829-11
1-216-833-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
4.7K
4.7K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R921
R923
R924
R925
R926
1-216-809-11
1-216-817-11
1-216-825-11
1-216-817-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
470
2.2K
470
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
Part No.
TUNE
Description
VOL
Remark
< ROTARY ENCODER >
S813
1-480-223-11 ENCODER, ROTARY (VOLUME)
*************************************************************
MISCELLANEOUS
***************
58
214
CN2
1-834-138-21 CABLE, FLEXIBLE FLAT (18 CORE)
1-834-139-21 CABLE, FLEXIBLE FLAT (10 CORE)
1-817-371-21 CONNECTOR, COAXIAL (F TYPE)
(ANTENNA (FM))
IDM1
A-1256-714-A IDM MODULE
LCD401 1-802-474-11 DISPLAY PANEL, LIQUID CRYSTAL
M950
1-787-396-11 FAN, D.C. (50 SQUARE)
SP101 1-826-688-11 SPEAKER (6.6cm) (R-CH)
SP201 1-826-688-11 SPEAKER (6.6cm) (L-CH)
0 T901
1-480-224-11 POWER UNIT, AC
TU1
A-1256-754-A TUNER UNIT, DSP
*************************************************************
ACCESSORIES
************
1-754-102-31
1-754-537-11
1-793-184-23
1-833-072-11
3-208-169-11
ANTENNA, LOOP (AM)
ANTENNA, DIPOLE (FM)
CONNECTOR (F TYPE ADAPTOR) (FM)
CORD (WITH PLUG) (SP-SP) (AUDIO)
MANUAL, INSTRUCTION (ENGLISH)
A-1259-028-A REMOTE COMMANDER (RMT-CS3A)
(including BATTERY LID)
R927
1-216-821-11 METAL CHIP
1K
5%
1/10W
R928
1-216-841-11 METAL CHIP
47K
5%
1/10W
R929
1-216-841-11 METAL CHIP
47K
5%
1/10W
R940
1-216-841-11 METAL CHIP
47K
5%
1/10W
*************************************************************
A-1257-300-A TUNE BOARD, COMPLETE
*********************
< RESISTOR >
R830
R831
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1/10W
1/10W
< ROTARY ENCODER >
S812
1-480-223-11 ENCODER, ROTARY (TUNE/SELECT)
*************************************************************
A-1257-298-A VOL BOARD, COMPLETE
********************
< RESISTOR >
R832
R833
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1/10W
1/10W
35
XDR-S3HD
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
1.0
36
Date
2007. 05
Description of Revision
New