Download flat bed sling user guide

EasiDec Wet Floor Installation
- Timber Floor
Gravity waste for wet floor
exploded view
Gravity waste for wet floor
plan view
106mm
Alternative drilling positions
to overcome typical site conditions
(50mm diameter)
Removable inner cup
Locking nut
Rubber seal
98mm depth
(assembled)
Shower trap
body
100mm
1 1/2”- “Multifit”
TYPICAL CROSS SECTION THROUGH WET FLOOR ‘EASIDEC’
- TIMBER FLOOR CONSTRUCTION
150mm Altro upstand
35mm cove former
‘Altro Marine 20’
7
2
Altro
Captile
profile
46
16
Altro
Self levelling compound
6mm water proof based ply
Altro Captile
profile
A
18
35
Ceiling (room below)
A - 150mm joist typical
75mm X 50mm supporting
noggin spaced at 500 centres
Altro Coveformer
18
2
35
Gravity waste
Altro Coveformer
If you require additional help or information or training please contact:
126 Churchill Road, Bicester, Oxon OX26 4XD
Northern Ireland: 5 Balloo Way, Balloo Industrial Estate,
Bangor, Co Down BT19 7QZ
Tel: +44 (0) 1869 365500
Tel: 028 9145 0497
Fax: +44 (0) 1869 365588
Fax: 028 9127 0046
Wet Floor Installation- Timber Floor
Check contents
Check contents.Carefully unpack the EasiDec and check for any
damage. Chiltern Invadex will take no responsibility for damage once
the EasiDec is installed. Damage must be notified to the company in
line with its Terms and Conditions of sale. Always ensure that the
correct waste outlet has been ordered for use with the EasiDec. This
will be a gravity waste with a compatible trap for use on a timber floor.
Safety considerations
Fig 1
Care should always be taken when handling heavy or awkward loads.
1. Positioning the EasiDec & cutting floorboards
Fig 2
Place the EasiDec in position and mark around with a pencil, as Fig 1.
Carefully cut out floorboards within the area marked. Place the EasiDec
in position to ensure good fit. Provide noggins where necessary to
support the centre and edges of the EasiDec. The EasiDec must not
overhang any joist at its edges by more than 25mm.
Chipboard floor - Ensure the EasiDec is flush with the chipboard as Fig
2. If not pack up as necessary. Timber floors - The EasiDec should sit
proud of the timber floor by a thickness of hardboard which will butt up
flush against it for eventual covering. Ensure the EasiDec is level on all
four sides. Remove the EasiDec.
2. Fitting the Waste and Gulley
Fit the waste pipe and trap. The trap must be positioned to line up with
the gulley aperture in the EasiDec, as Fig 3. Place the plastic gulley in
position on the EasiDec. Mark and drill the four fixing holes with a
3.5mm drill. Fix the gulley to the EasiDec using 8 x ¾” stainless steel
self tapping screws.
Fig 3
Drill the gulley with a 50mm hole saw to line up with the trap (this hole
can be offset slightly if required to suit). Place the EasiDec in position,
as Fig 4. If required timber noggins or similar must be used to provide
support. Place noggins centrally to support the EasiDec where possible.
Ensure the EasiDec is in contact with all support timber by bedding it on
expanding foam, grip fill or silicone. Secure the trap to the gulley using
the threaded waste parts provided.
Check EasiDec is level on all 4 sides.
Fig 4
Fig 4
4. Fixing the EasiDec
Fig 5
Screw the EasiDec down using the No 10 x 1 ½ “ stainless steel self
tapping screws provided. The EasiDec must be screwed down in at
least 8-14 positions - about 25mm (1”) from the side edge/perimeter by
slot drilling and countersinking. The EasiDec can be drilled,
countersunk and screwed anywhere in the showering area. Slot drilling
is essential to allow natural movement and shrinkage of timber. The
screws must have movement. Do not overtighten the screws. The
screw heads must be flush with the surface of the EasiDec. Complete
the installation in the conventional manner, covering the EasiDec with
vinyl flooring, as Fig 5. The EasiDec can be latexed to accommodate
uneven surfaces.
Copyright  Chiltern Invadex Ltd The design of the product shown on this sheet is vested in Chiltern Invadex Ltd and should not be copied or reproduced in any way whatsoever without the
express permission in writing of Chiltern Invadex Ltd. As part of our commitment to new product development we reserve the right to alter specifications without prior notice.
This is an original design of Chiltern Invadex Ltd in which Design Right Subsists.
Published by: Chiltern Invadex Ltd, 126 Churchill Road, Bicester, Oxon, OX26 4XD Registered in England No: 6050608
CINV 529.01 10/07
In Northern Ireland: Chiltern Invadex (NI) Ltd, 5 Balloo Way, Balloo Industrial Estate, Bangor, County Down, BT19 7QZ Registered No: NI 19958
EasiDec Wet Floor Installation
- Concrete & Floating Floor
Pumped waste for wet floor
exploded view
22mm/15mm speed fit connector
45mm
Depth in relation to
underside of gulley lip
130mm diameter lower cup
with 22mm side spigot
15mm diameter pipe
to suit site conditions
FLOATING FLOOR WITH
VINYL FLOORING
CONCRETE FLOOR WITH
VINYL FLOORING
Tiled finish
Captile
profile
Captile
profile
Wet floor
gulley
35mm
Cove former
35mm
Cove former
Tiled finish
Wet floor
gulley
35mm
Cove former
35mm
Cove former
Plywood
Altro marine 20
(or similar)
Chiltern Invadex
EasiDec
Typical 50mm
screed
Typical 150mm
pre-cast concrete
Chiltern Invadex
EasiDec
Altro marine 20
(or similar)
Typical one way
Typical 50mm
spanning ribbed, troughed
screed
or waffle floor - minimum thickness 75mm
TYPICAL CROSS SECTION THROUGH WET FLOOR ‘EASIDEC’
- CONCRETE FLOOR CONSTRUCTION
7
2
Chltern Invadex Easidec
35mm cove former
‘Altro Marine 20’
Altro
Captile
profile
46
16
Altro
6mm plyboard
Altro Captile
profile
Whale assembled
gulley
18
35
Self levelling
compound
Typical 50mm screed
Weak sand/cement mix
or expanding foam
Typical 150mm
pre-cast concrete
Altro Coveformer
18
2
35
Altro Coveformer
Wet Floor Installation - Concrete Floor
Check the contents
Carefully unpack the EasiDec and check for any damage. Chiltern
Invadex will take no responsibility for damage once the EasiDec is
installed. Damage must be notified to the company in line with its
Terms and Conditions of sale. Always ensure that the correct waste
outlet has been ordered for use with the EasiDec. Typically, this will be a
pumped waste outlet with a Whale Pump (site conditions permiting)
Safety considerations
Fig 1
Care should always be taken when handling heavy or awkward loads.
1. Positioning the EasiDec & removing concrete
Decide on the position of the EasiDec. Place the EasiDec in position
and mark around with a pencil, as Fig 1. Carefully remove all concrete
within the marked area to a thickness of 25mm. Mark position of waste.
Fig 2
Place the EasiDec in position to ensure good fit. Always ensure the
EasiDec is level on all 4 sides and flush with the finished concrete floor
as Fig 2. A proprietry self levelling compound can be used to make level
and smooth off rough edges.
2. Fitting the Waste Gulley
Remove sufficient concrete for installation of the waste pipe and gulley.
Drop the gulley into the preformed hole. Adjust the waste outlet to the
desired angle, as Fig 3.
Fit the waste pipe and trap and align with the centre of the gulley.
Fig 3
To fix the gulley to the EasiDec, drill 4 x 3.5mm holes through the
marked position on the gulley and straight through the EasiDec. Fix the
gulley in position using 3/4” x 8 stainless steel self-tapping screws.
3. Connect waste pipe
Connect the waste pipe by reaching under the EasiDec and solvent
cementing (or speed fitting) the pipe to the gulley (if this is not possible,
glue a short length of waste pipe to the gulley before it is lowered into
position), as Fig 4.
4. Fixing the EasiDec
Fig 4
Bed the EasiDec on a weak sand/cement mix or expanding foam to
ensure it is fully supported (do not overfill with expanding foam). Check
the EasiDec is level on all 4 sides and flush with the finished concrete
floor. Complete the intallation in the conventional manner, covering the
EasiDec with vinyl flooring. The EasiDec can be latexed to accommodate
uneven surfaces.
If you require additional help or information or training please contact:
126 Churchill Road, Bicester, Oxon OX26 4XD
Northern Ireland: 5 Balloo Way, Balloo Industrial Estate, Bangor, Co Down BT19 7QZ
Tel: +44 (0) 1869 365500
Tel: 028 9145 0497
Fax: +44 (0) 1869 365588
Fax: 028 9127 0046
Copyright  Chiltern Invadex Ltd The design of the product shown on this sheet is vested in Chiltern Invadex Ltd and should not be copied or reproduced in any way whatsoever without the
express permission in writing of Chiltern Invadex Ltd. As part of our commitment to new product development we reserve the right to alter specifications without prior notice.
This is an original design of Chiltern Invadex Ltd in which Design Right Subsists.
Published by: Chiltern Invadex Ltd, 126 Churchill Road, Bicester, Oxon, OX26 4XD Registered in England No: 6050608
CINV 530.01 10/07
In Northern Ireland: Chiltern Invadex (NI) Ltd, 5 Balloo Way, Balloo Industrial Estate, Bangor, County Down, BT19 7QZ Registered No: NI 19958
CINV xxx.xxx 08/07