Download User's Manual
Transcript
1 SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat. 9) Only use the attachments/accessories specified by the manufacturer. 10) Use only with a cart, stand, tripod or bracket specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12) Unplug this apparatus during lightning storms or when unused for long periods of time. 13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has be en damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled o r objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, doe s not operate normally, or has been dropped. Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock does not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. In USA and Canada, Use Class 2 Power Supply Only 2 Contents 1. Product Features .................................................................................................................................... 5 2. Accessing the Camera............................................................................................................................ 9 2.1 2.2 2.3 2.4 2.5 2.6 Access from a browser.................................................................................... 9 Accessing the camera from the Internet ........................................................... 10 Adjusting the Image and Focus ...................................................................... 10 The Live View page ....................................................................................... 10 Video stream types ....................................................................................... 11 How to stream H.264 .................................................................................... 11 3. The Setup .............................................................................................................................................. 12 4. Analog output ....................................................................................................................................... 13 4.1 Analog Output Setup .................................................................................... 13 5. Video ...................................................................................................................................................... 13 5.1 Codec ......................................................................................................... 13 5.2 Camera ....................................................................................................... 16 5.2.1 Exposure Control .................................................................................... 16 5.2.2 Day & Night Control ................................................................................ 17 5.2.3 White Balance Control ............................................................................. 17 5.2.4 Image Property Control ............................................................................ 17 5.2.5 Lens Adjustment .................................................................................... 17 6. Audio ...................................................................................................................................................... 18 7. Live......................................................................................................................................................... 19 7.1 7.2 Setup ........................................................................................................ 19 Privacy Masking ......................................................................................... 20 8. FTP ......................................................................................................................................................... 21 8.1 FTP > Config ............................................................................................... 21 8.2 FTP > Event ................................................................................................. 21 8.3 FTP > Periodical ........................................................................................... 22 9. Event ...................................................................................................................................................... 23 9.1 Event > Alarm Port ........................................................................................ 23 9.2 Event > Motion ............................................................................................. 24 9.3 Event > Mapping .......................................................................................... 25 10. Network................................................................................................................................................ 26 10.1 10.2 10.3 10.4 10.5 10.5 Network Network Network Network Network Network > > > > > > IP Setup ..................................................................................... 26 Service Port ................................................................................ 28 RTP ........................................................................................... 28 E-mail ........................................................................................ 29 DDNS ......................................................................................... 29 UPnP ......................................................................................... 30 11. System ................................................................................................................................................. 31 11.1 11.2 11.3 11.4 System System System System > > > > User ............................................................................................ 31 Date & Time ................................................................................. 32 Maintenance ................................................................................ 33 Information .................................................................................. 35 12. Dimension (mm) .................................................................................................................................. 36 3 13. Specification ....................................................................................................................................... 37 4 1. Product Features The GANZ PixelPro is a high performance H.264 network camera, designed for demanding security installations. It delivers crisp, clear images, disclosing every detail, thanks to its top quality Megapixel progressive CMOS sensor and advanced image processing. Supported by the industry’s largest base of video management software, the GANZ PixelPro provides the perfect solution for securing bank offices, airports and other facilities, and for traffic surveillance, over IP based networks. The optimal Power over Ethernet (IEEE 802.3af) support power to the camera to be delivered via the network, eliminating the need for a power outlet and reducing installation costs. Steady power could be guaranteed with a central Uninterruptible Power Supply (UPS). The GANZ PixelPro offers a comprehensive set of network security and management features. This includes support for port based network control (IEEE802.1X), which allows the camera to be connected to a network secured with this control, and HTTPS encryption, which provides a secure channel between camera and application. It also enables authentication of the video source. Video products are efficiently managed with the powerful Management tool, which is provided on the Installation CD which comes with camera. 5 1. Network connector (RJ-45 PoE supported) The GANZ PixelPro connects to the network via a standard network cable, and automatically detects the speed of the local network segment (10BaseT/100BaseTX Ethernet). This socket could also be used to power the GANZ PixelPro via Power over Ethernet (PoE). The camera auto-senses the correct power level when using a PoE switch, router or injector. 2. Power connector 12 VDC or 24VAC power connector 3. I/O Signal terminal block Audio in Audio in (line level), for line-in mono signal (only left channel is used from a stereo signal) 6 Audio out The Audio output (line level), which could be connected to a line output of a microphone system or an active speaker with a built-in amplifier. Alarm in One analog (dry contact) alarm input Alarm out One relay output (0.5A 125VAC / 1A 30VDC) 4. Control Button This button has 3 functions by pressing time. 1) Switch NTSC / PAL format (less than 1 second) 2) System reboot (around 5 seconds) 3) Factory Default Reset (More than 10 seconds) 5. Video output for service monitor This analog video output is available. Use accessory cable to video output. 6. Status LED LED Color Indication On Green Flashes Unlit Amber - System Status Connection to 10/100Mbps Network / LAN. Network connection is established. Indication of network activity. Camera is booting up. No network connection established. When no or incorrect power is supplied. On Camera reset is in progress. Flashes Factory Default settings are in progress. 7 Installation Preparation 1) Turn the bottom cover clockwise and separate the unit and the cover. 2) Separate the top cover and the camera unit. 3) Make holes for cables to ceiling / wall with supplied template. 1 2 3 Mounting to a ceiling / wall 4) Secure the bottom cover to a ceiling / wall with two supplied tapping screws (4x30) and anchors. 5) Attach the unit to the bottom cover and turn it counter clockwise. Then secure the unit with two supplied tapping screws (3x8). 6) Attach the top cover to the unit. 4 5 6 8 2. Accessing the Camera Follow the instructions in the GANZ PixelPro Installation Guide to install the camera. The GANZ PixelPro could be accessed with most standard operating systems and browsers. The recommended browser is Internet Explorer for Windows with other operating systems. 2.1 Access from a browser 1. Start a browser (Internet Explorer) 2. Enter the IP address or host name of the camera in the Location/Address field of your browser. Press Enter. 3. Login dialog will appear when the camera is accessed for the first time. 4. The default user name is ADMIN, and password is 1234. 5. The camera’s Live View page is now displayed in your browser. Note: The layout of the live view page in the camera may have been customized to meet specific requirements. Consequently, some of the examples and functions featured here may differ from those displayed on your own Live View page. 9 2.2 Accessing the camera from the Internet Once installed, the camera is accessible on the local network (LAN). Configure the router/firewall to allow incoming data traffic to access the camera from the Internet. For security reasons this is usually done on a specific port. Please refer to the documentation for router/firewall for further instructions. 2.3 Adjusting the Image and Focus To adjust the position of the lens: 1. Open the Live View page in your web browser. - Select the Setup tab, and open the Analog output page. - Select the ‘Video Format'. 2. Connect analog monitor to the VIDEO OUT (BNC) on the supplied cable. - Control the ZOOM/FOCUS by the Lens Adjustment window, and adjust the camera angle. For lens adjustment method, please refer to “5.2.5 Lens Adjustment”. 3. Check the image from the Live View page on your web browser. 4. You can refocus adjustment by Lens Adjustment window, if you want fine lens adjustment. 2.4 The Live View page Enable/Disable PC Speaker output Enable/Disable PC Microphone input Digital Zoom Snap Shot Full Screen Video Stream change: First stream Second stream Play: Click this button by manually to start the stream Stop: Click this button by manually to stop streaming NOTE: It is possible that not all the buttons described below will be visible unless the Live View page has been customized to display them. 10 2.5 Video stream types H.264 protocols and communication methods • RTP (Real-time Transport Protocol) is a protocol that allows programs to manage the real-time transmission of multimedia data, via unicast or multicast. • RTSP (Real Time Streaming Protocol) serves as a control protocol, to negotiate the type of transport protocol to use for the stream. RTSP is used by a viewing client to start a unicast session. • UDP (User Datagram Protocol) is a communications protocol that offers limited service for exchanging data in a network which uses the Internet Protocol (IP). UDP is an alternative to the Transmission Control Protocol (TCP). The advantage of UDP is that, it is not required to deliver all data and may drop network packets when there is network congestion. This is suitable for live video, as there is no point in retransmitting old information that will not be displayed anyway. • Unicasting is communication between a single sender and a single receiver over a network. This means that the video stream goes independently to each user, and each user gets own stream. A benefit of unicasting is, in case one stream fails, it only affects one user. • Multicasting(Will be supported)is bandwidth-conserving technology that reduces bandwidth usage by simultaneously delivering a single stream of information to multiple network recipients. This technology is used primarily on delimited networks (intranets), as each user needs an uninterrupted data flow and should not rely on network routers. 2.6 How to stream H.264 Deciding on the combination of protocols and methods to use depends on your viewing requirements, and on the properties of your network. Setting the preferred method(s) is done in webpage. RTP+RTSP This method (actually RTP over UDP and RTSP over TCP) should be your first consideration for live video, especially when it is important to always have an up-todate video stream, even if some images are lost due to network problems. This could be configured as multicast or unicast. RTP/RTSP/Multicasting (Will be supported) provides the most efficient usage of bandwidth, especially when there are large numbers of clients viewing simultaneously. Note however, that a multicast broadcast could not pass a network router unless the router is configured to allow this. For example, It is impossible to multicast over the Internet. 11 RTP/RTSP/Unicasting should be used for video-on-demand broadcasting, so that there is no video traffic on the network until a client connects and requests the stream. However, as more and more unicast clients get connected, the traffic on the network will increase and may cause congestion. Although there is a maximum of 10 unicast viewers, note that all multicast users combined count as 1 unicast viewer. RTP/RTSP This unicast method is RTP tunneled over RTSP. This could be used to exploit the fact that it is relatively simple to configure firewalls to allow RTSP traffic. 3. The Setup The GANZ PixelPro is configured from the Setup link, which is available on the top left hand side in the web interface. This configuration could be done by: • Administrators, who have unrestricted access to all settings under the Setup tab. Accessing the Setup link from a browser 1. Start your web browser and enter the IP address or host name of the camera into the address bar. 2. The Live View page is now displayed. Click on the Setup tap. 12 4. Analog output 4.1 Analog Output Setup Analog output allows selection of output format of the analog BNC output from the camera. NTSC, PAL: Analog Output is selectable. 5. Video The following descriptions show examples of some of the features available in the GANZ PixelPro. 5.1 Codec These are the tools for adjusting the H.264 settings and controlling the video bit rate. 13 H.264 This is a video compression standard that makes good use of bandwidth and which could provide high-quality video streams at less than 1 Mbit/s. The H.264 standard provides scope for a large range of different coding tools for use by various applications in different situations, and the GANZ PixelPro provides certain subsets of these tools. Using H.264, it is also possible to control the bit rate, which in turn allows the amount of bandwidth usage to be controlled. CBR (Constant Bit Rate) is used to achieve a specific bit rate by varying the quality of the H.264 stream. While using VBR (Variable Bit Rate), the quality of the video stream is kept as constant as possible, at the cost of a varying bit rate. Motion JPEG This format uses standard JPEG still images in the video stream. These images then are displayed and updated at a rate sufficient to create a stream that shows constantly updated motion. The Motion JPEG stream uses considerable amounts of bandwidth, but also provides excellent image quality and access to every individual image contained in the stream. Multiple clients accessing Motion JPEG streams could use different image settings. Codec H.264 / MJPEG Size Video output resolution. See the next page for the output resolution table. Frame rate 1~30fps in normal mode (1~15fps for slow shutter mode) Note: If the slow shutter mode is turned on and the low light condition is met, the frame rate is automatically goes down. In this case, the frame is half of the normal mode. GOP Size 1 ~ 60 frames Bit-rate control (CBR or VBR) When using H.264 compression, if there is only limited bandwidth available, a constant bit rate(CBR) is recommended, although this may compromise image quality. Use a variable bit rate(VBR) for the best possibly image quality. 14 Average Bit-rate (512Kbps ~ 10Mbps) Recommended bit rate for D1: 800Kbps ~ 1Mbps Recommended bit rate for 1.3M(720p): 3Mbps ~ 4Mbps Recommended bit rate for 2.0M(1080p): 6Mbps ~ 8Mbps Anti-Flicker mode (Flicker less mode) 60Hz:NTSC 50Hz:PAL or flicker-free mode(to use the camera in locations lit by fluorescent lighting). Video Mirroring Select Video Mirroring mode NONE/ HORIZONTAL / VERTICAL / FLIP(H+V) Bandwidth Limit Limit the bandwidth that the GANZ PixelPro can use during a network connection. Max Bandwidth Specify the maximum bandwidth that the GANZ PixelPro can use during a network connection. < Output resolution table for PixelPro> First Stream Second Stream 1920x1080 704x480 640x480 640x360 640x352 352x288 352x240 320x240 - 1280x1024 704x480 640x480 640x360 352x288 352x240 320x240 - - 1024x768 704x480 640x480 640x360 352x288 352x240 320x240 - - 704x576 704x480 640x480 640x360 352x288 352x240 320x240 1280x720 1280x72 0 704x576 704x576 640x480 640x360 352x288 - - - - 704x480 704x480 640x480 640x360 352x240 - - - - 640x480 640x480 320x240 - - - - - - 640x360 640x360 320x240 - - - - - - 352x288 352x288 - - - - - - - 352x240 352x240 - - - - - - - 320x240 320x240 - - - - - - - 15 5.2 Camera This section allows you to adjust various camera settings. 5.2.1 Exposure Control Enable AE (Auto Exposure) ON: Use this setting for automatic exposure control. OFF: Use these settings to control camera exposure manually. To compensate for poor lighting conditions, you can adjust the Color level, Brightness, Sharpness, Contrast and Exposure control. NOTE: When AE is enabled, some of the submenus (AGC Gain, e-Shutter Speed) will be disabled. Slow shutter mode For low light conditions, turn on slow shutter mode. Max AGC Gain For low light conditions, adjust to a higher value, such as 30dB. 16 BLC Control (Back Light Compensation) The BLC adjusts the exposure of scenes with strong backlight in the center-bottom of the image. When the image background is too bright, or the subject too dark, backlight compensation makes the subject appear clearer. The settings for low light behavior determine how the camera behaves sat low light levels. These settings affect video image quality and how much noise is in the images. 5.2.2 Day & Night Control Day & Night Mode Auto/Day/Night- If set to Auto, the camera will automatically switch according to the current lighting conditions. 5.2.3 White Balance Control WB Mode ON: ATW (Automatic White balance) OFF: MWB (Manual White balance) The White balance adjustment setting is used to make the colors in the image appear consistent, compensating for the different colors present in different light sources. The GANZ PixelPro camera can be set to automatically identify the light source and compensate for its color temperature. If necessary, the type of light source could be set manually.. 5.2.4 Image Property Control Modify the video signal parameters, such as: Brightness, Sharpness, Contrast, and Color. Sharpness (Default: 8, Range: 1~15) Brightness (Default: 15, Range: 0~30) Contrast (Default: 15, Range: 0~30) Color (Default: 15, Range: 0~30) 5.2.5 Lens Adjustment Adjust the lens (Zoom, Focus & Iris) from this window. One Push Focus : Camera will automatically adjust the focus. Default : Back to initial position(wide end). 17 6. Audio The GANZ PixelPro camera could transmit audio to other clients, using a connected external microphone and could play audio received from other clients via connected speakers. This section describes how to configure the basic audio settings for the GANZ PixelPro camera, such as setting the communication mode, adjusting the sound levels in the microphone and speakers connected to the camera. Note: The speakers connected to the audio output must have a built-in amplifier, such as PC speakers. Audio ON/OFF : Check this to enable audio in the GANZ PixelPro camera. Codec G.711 u-law MIC Volume Speaker Volume Adjust the MIC and Speaker Volume. Audio Input Audio from a connected a line source could be connected to the Audio in connector of the GANZ PixelPro camera. If there are problems with the sound input being too low or high, adjust the input gain for the microphone connected to the GANZ PixelPro camera. 18 7. Live 7.1 Setup The GANZ PixelPro could support 10 simultaneous users. In case of multicast, the GANZ PixelPro could support unlimited number of users. If supported on the network, consider using multicasting, as the bandwidth consumption will be much lower. Viewer Setup LiveView Protocol RTP Unicast (UDP) / RTP Multicast (UDP) / RTP over RTSP (TCP) Buffering Time (frame based) Determines (0 ~ 90) x 1/30 sec (0 ~ 3sec) Viewer OSD Setup Date : Determines whether the date is displayed. Resolution : Determines whether the camera title is displayed. Event State : Determines whether the event state is shown on display window. 19 7.2 Privacy Masking This uses masking to hide sections that you do not want to appear in the shooting screen. A maximum of 2 locations can be set. Mask Area All View:Shows the masking area both Area 1 and 2. Click the Masking Area 1 or 2 to make a masking. Mask color Sets the mask color Black, White, Light Gray, Dark Gray, Yellow, Red, Blue, Green Mask Creation Procedure 1. Click Privacy Mask in the Live menu. 2. Select Area1 or 2 to activate a setup window. 3. Set the Mask Color in the drop-down list. 4. Click the Masking window, and select an area that you want to specify the masking area. 5. Click Save. Note: When the Privacy Masking is set, analogue output will be changed to off state automatically. * Privacy masking is available from FW1227 and later. 20 8. FTP 8.1 FTP > Config Server Configuration (This function is N/A on this model) External Server Configuration It is setting page to transmit the still shot to remote sites, using the FTP server. Specify the external FTP server information such as IP address, port number, Username and password. Note : When the first stream is set to 1920x1080, please set the 2nd stream to MJPEG or H.264 with resolution less than 352x288. If 2nd stream is set to H.264 greater than 640x352, 30fps streaming is not guaranteed due to performance limitation. 8.2 FTP > Event 21 Event FTP Sending It enables FTP transmission triggered by event. Directory : This folder will be created into external FTP server automatically. File Prefix : The file name will start from this prefix. Mapping : You can specify event mapping for Event FTP. Effective Period : You can specify “Always” or “Schedule” 8.3 FTP > Periodical Periodical FTP Sending It enables FTP transmission periodically. Directory : This folder will be created into external FTP server automatically. File Prefix : The file name will start from this prefix. Interval : You can specify interval time for uploading to FTP. Effective Period : You can specify “Always” or “Schedule” 22 9. Event 9.1 Event > Alarm Port Alarm Input - Used for connecting external alarm devices and triggering images for specific alarm-based events. The input is typically connected to a motion detector or any other external security device, and images could be uploaded whenever the detector is activated. Maximum 5VDC is allowed on the input. Output - This could drive a maximum load of 0.5A 125VAC / 1A 30VDC directly or heavier loads by connecting additional relay circuitry. If the output is used with an external relay, a diode must be connected in parallel with the load for protection against any voltage transients. Duration - This parameter sets the minimum tampering period, that is, an alarm will not be triggered until this period has lapsed, even if the tampering conditions are otherwise met. This could help to prevent false alarms for known conditions that affect the image. Caution! Connecting AC to the inputs/outputs will damage the unit. 23 9.2 Event > Motion Motion Detection Motion detection is used to generate an alarm whenever movement either occurs or stops in the video image. A maximum of 4 windows could be configured. Area Sensitivity:1(low) ~ 10(High) – The higher the number is, the higher the sensitivity level becomes. Configuring Motion Detection 1. Click Motion Detection in the Event Config menu. 2. Select an Area from Area1 to 4 to activate a Motion setup window. 3. Click the Motion window, and select an area that you want to specify the Motion area. 4. Select sensitivity value (1 ~ 10) in the drop-down list. Any detected motion within an active window is then indicated by red shade onto the Activity window. 5. Click Save. Note: Using the motion detection feature may decrease the camera’s overall performance. 24 9.3 Event > Mapping It is possible to define conditions that would cause the camera to respond with certain actions. A triggered event happens as a result of a trigger, which could be motion detection or an external alarm input. For example, Alarm out events could be triggered by video motion detection or alarm in. E-mail could be sent by video motion detection or alarm in. 25 10. Network 10.1 Network > IP Setup Network Settings Click the Setup > Network > IP Setup to see the current network settings. IP Address Configuration The GANZ PixelPro supports both IP version 4 and IP version 6 (IPv6 will be supported in V3.00). Both versions may be enabled simultaneously, and at least one version should be always enabled. When using IPv4, the IP address could be set automatically via DHCP, or a static IP address could be set manually. If IPv6 is enabled, your camera receives an IP address according to the configuration in the network router. There are also options for setting up notification of changes in the IP address, and for using the Internet Dynamic DNS Service. Notes: • To receive notification whenever the camera’s IP address changes (via e.g. DHCP), configure the options for notification of IP address change. See Services below. • If your DHCP server could update a DNS server, you could access the GANZ PixelPro by a host name which is always the same, regardless of the IP address. DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses on your network. •1st DNS server Enter the IP address of the primary DNS server for your network. •2nd DNS server Enter the IP of the Secondary DNS, which is used if the Primary DNS server is unavailable. 26 How to assign IP address Default setting is set to “DHCP” and “UPnP” function is set to ON. If your netwo rk has DHCP server and UPnP function is enabled on your PC, you can find t he network camera in “My network”. If DHCP server is not available in your network, please assign IP address as following process. ② ③ ④ 1) 2) 3) 4) Execute “MultiUpgradeTool.exe”, it will search the camera on the network. After the camera is listed in camera list, select the camera. Type in the all network information. Click “Change IP address” button to set network settings to the camera. When you double-click the camera within the list, the default web browser (Internet Explorer or compatible equivalent) will open and automatically connect to the camera. 27 10.2 Network > Service Port Service Port HTTP port- The default HTTP port number (80) could be changed to any port within the range 1-65535. This is useful for simple port mapping. RTSP port- The RTSP protocol allows a connecting client to start an H.264 stream. Enter the RTSP port number to use. The default setting is 554. NOTE: After changing the default port numbers, the user can use the “MultiUpgradeTool.exe” to search and connect automatically. 10.3 Network > RTP RTP port range , Multicast Setup These settings are the IP address, port number, and Time-To-Live value to use for the video stream(s) in multicast H.264 format. Only certain IP addresses and port numbers should be used for multicast streams. 28 10.4 Network > E-mail You must turn Notification to ‘On’ and then enter the host names or addresses for your mail servers in the fields provided, to enable the sending of event and error email messages from the camera to predefined addresses via SMTP. Note1) Frequency : Mail server may register the sender to SPAM list when frequency is set to “1 Min”. It may be better to set “5 Min” for safe side. Note2) From : Specify the name who sent e-mail notification. It may be better to use e-mail format like as [email protected]. Some e-mail server will refuses it. 10.5 Network > DDNS 29 How to setup the DDNS: 1) DDNS set to ON. “mac address.dvrlink.net” is registered to the DDNS server. User can connect to the camera with: “http://mac address.dvrlink.net”. 2) DDNS set to ON and user inputs “user-defined name”. “mac address.dvrlink.net” and “user-defined name.dvrlink.net” are both registered together. User can connect to the camera using either: “http://mac address.dvrlink.net” or “http://user-defined name.dvrlink.net”. If “user-defined name” is already registered, an error message is shown, try a different name. 10.5 Network > UPnP Universal Plug & Play (UPnP) allows you to find the IP camera automatically on your network. In order to be able to detect the camera automatically, you must enable the UPnP function on both the camera and on your PC. 30 Camera : Set UPnP to “ON” PC : Open “Control Panel” >”Network Connection” Select “Advanced” >”Optional Networking Components…” Select “Network Services” and click “Details”. Then select “UPnP user Interface” 11. System 11.1 System > User Access the camera and the Configure Root Password dialog appears. Enter the User name: ADMIN and password is 1234. To changed password or add a user click SETUP > SYSTEM > USER. Fill the User ID, Password and E-mail server. Select Group. Then press ADD button and click SAVE. Note: The default administrator user name ADMIN is permanent and could not be deleted or altered. 31 11.2 System > Date & Time Date & Time Format - specify the formats for the date and time (12h or 24h) displayed in the Live View video streams. Use the predefined formats or use your own custom date and time formats. Network Time Server - the camera will obtain the time from an NTP server every 60 minutes. Specify the NTP server's IP address or host name. Time zone setup – Select your time zone from the drop-down list. D.S.T (Daylight Saving Time) - ON/OFF 32 11.3 System > Maintenance System Name Choose a system name to identify the camera when using e-mail notifications. System Reboot Reboot the camera. Factory Default To reset the camera back to the original factory default settings. Enable Firmware Upgrade / Firmware Updates To upgrade Firmware of the camera, follow the instruction below. NOTE: Preconfigured and customized settings should be saved before the firmware is upgraded. 1) Enable Firmware Upgrade mode with clicking “OK” of Enable Firmware Upgrade menu. 2) The camera automatically switch to Firmware Upgrade mode. 33 3) When Firmware upgrade menu is displayed, browse to the desired firmware file on your computer. Click OK. NOTE: Do not disconnect power to the unit during the upgrade. The unit will restart automatically after the upgrade has completed. (1~5 minutes) System Reset (Factory Default Reset) There are two ways to reset the camera back to factory default. holding down about 10-20 sec the reset button on the Network cable Using the web browser: 1. Go to SETUP > System > Maintenance. 2. Click Factory Default Button and wait 1 minute for camera to reboot. Using the Reset Button: 1. Holding down 15-20 sec the reset button on the Network cable. 2. Release your finger on the reset button, waiting about 1 minute for camera reboot NOTE: The unit will now have the default IP address from a DHCP server. Use the ‘“MultiUpgradeTool.exe” to discover and connect to the camera. 34 11.4 System > Information System Information You can confirm the system information if the camera here. 35 12. Dimension (mm) 36 13. Specification H.264 / MJPEG Network Camera Dual Stream Motion Triggered Alarm/ External Alarm In Multi Language GUI support ONVIF Compliant Triple Power. 12VDC, 24VAC, PoE(802.3af) SONY CMOS Sensor IMX122 On The Fly supported @ GOP/Bitrate/FPS stetting 2D DNR. (Depends on CODEC configuration) - 3D TBD Product Features DPC(Defective Pixel Correction) on the fly 18 IR LEDs (IR model) Motorized Zoom, Focus and P-iris True Day & Night Analog Hybrid Output(Installation Only) Privacy Masking Image Sensor Max. Resolution Effective Pixels Effective Image Size White Balance Electronic Zoom AGC BLC Iris CAMERA Shutter Speed Slow Shutter Lens Angle of View Day & Night S/N ratio Min. illumination ANALOG (Installation Only) AUDIO Video Signal Monitor Output Scanning Frequency In/Out CODEC 1/2.8" Sony IMX122 CMOS Sensor 1920 x 1080; (2MTP), 1280 x 1024; (1MTP) 1984(H) x 1225(V) 5.56mm(H) x 3.43mm(V), 6.53mm(Diagonal) ATW / MANUAL(PRESET) 2 ~ 10x(Client Software) Yes Yes Motorized Iris / MANUAL / AES 1/4, 1/10, 1/12.5, 1/15, 1/20, 1/25, 1/30, 1/50, 1/60, 1/100, 1/120, 1/240, 1/480, 1/960, 1/1024, 1/2000s 2x, 4x, 8x Motorized Zoom and Focus lens f=3~9mm, F1.2~2.1 Horizontal ; f=3mm(Wide) 104.2°, f=9mm(Tele) 35.5° Removable IR Cut Filter 48.8 dB or more 0 lux with IR LED ON ;IR model 0.16 lux(F1.2, 50IRE) ;w/o IR model NTSC / PAL selectable Composite Output(BNC), 75 ohm 1Vpp NTSC: (H) 15.734 kHz, (V) 59.94 Hz PAL: (H) 15.625 kHz, (V) 50 Hz Line in, Line out External Amplifier is needed G.711 / 8K sampling 37 Network Image Compression 10BASE-T, 100BASE-TX, RJ45 H.264 MJPEG : Image quality: 100 Steps(Q value) 1920 x 1080(Full HD; 2MTP), 1280 x 1024(SXGA), Resolution 1024x768(XGA), 1280 x 720(720p) 640 x 480(VGA), 640 x 360(HVGAW), 320 x 240(QVGA) 704x480/576(4CIF), 352x240/288(CIF) IPv4, HTTP, SMTP, UPnP, DNS, Protocol RTSP, DDNS, RTP, TCP, UDP, RTCP, DHCP, ARP, IGMP, ICMP, NTP Frame Rate NETWORK 1 fps ~ 25 fps / 1 fps ~ 30 fps Internet Explorer 7.0 or above Web Browser Firefox Chrome PDA / Smart phone Security Password Protection SDK(API) HTTP based API ONVIF Profile S VMD Alarm Trigger Alarm Event Power Consumption POWER Power Consumption (IR model) Heater Micro SD Card External I/O Terminals IR Number FAN Number OTHER SPECIFICATIONS Ambient Temperature (not cold start) Ambient Humidity Materials Weight Dimensions(W x H x D) User set 4 ROI(Region Of Interest) 10 Step Sensitivity VMD, External Alarm Input E-mail notification(Snapshot), FTP transfer(Snapshot), Video streaming with alarm status 500mA @ DC12V, 6.0W 420mA @ AC24V, 6.2W 120mA @ DC48V(PoE), 5.8W 680mA @ DC12V, 8.2W 510mA @ AC24V, 7.5W 150mA @ DC48V(PoE), 7.2W Alarm In x1: NO/NC Dry contact Alarm Out x1: Relay output Audio In x1, Audio Out x1 18 IR LEDs (IR model) -5ºC ~ +45ºC(23ºF~113ºF) less than 90%, Non-condensing Poly Carbonate 2(PC2) 0.4kg 124.7(D) x 119(H) mm 38 39 40 159-1.1 41