1
Download user manual - Grote Software Systems
Transcript
Grote Software Systems FMcapture © user manual Grote Software Systems Content: manual FMcapture® for FMcapture 3.0® Windows® XP, Windows Vista®, Windows® 7 and Windows® 8 version 3.0.12.1 03/31/2013 2 Version 3.0.12.1 03/31/2013 Grote Software Systems Content 1 Introduction ................................................................................................................................... 4 1.1 Copyrights and Trademarks .............................................................................................................. 4 2 System Requirements ................................................................................................................... 5 2.1 Desktop-PC, Notebook and Tablet-PC.............................................................................................. 5 3 Installation / Setup Options .......................................................................................................... 6 3.1 Installation .................................................................................................................................... 6 3.1.1 First Segment – License Request .............................................................................................. 6 3.1.2 Second Segment – Program Installation .................................................................................. 8 3.2 Repairing ....................................................................................................................................... 9 3.3 Uninstall ...................................................................................................................................... 10 4 Program handling ........................................................................................................................12 4.1 Program start .............................................................................................................................. 12 4.2 Start Menu .................................................................................................................................. 12 4.3 Data Recording ............................................................................................................................ 13 4.3.1 Measurement - Catenary height ............................................................................................ 15 4.3.2 Measurement - Catanery position ......................................................................................... 16 4.3.3 Measurement - Distance to PLE (PoleLeadingEdge) .............................................................. 17 4.3.4 Measurement - Catenary wear out ........................................................................................ 18 4.4 Data ............................................................................................................................................. 20 4.5 Data Export.................................................................................................................................. 22 4.6 Info .............................................................................................................................................. 25 4.7 Help ............................................................................................................................................. 25 4.8 Settings ........................................................................................................................................ 26 4.9 Finishing ...................................................................................................................................... 30 5 Troubleshooting / Hotline...........................................................................................................30 6 Imprint .........................................................................................................................................31 3 Version 3.0.12.1 03/31/2013 Grote Software Systems 1 Introduction © Thank you for purchasing the software FMcapture . With this product you can achieve a significant improvement in the range of use and operating with the catenary measuring instruments from the company Feinmess Dresden GmbH. © With the software FMcapture you can describe the height of catenary, the location to the track axis (sine or zigzag) and the catenary wear digital recording with up to three attributes (name can be chosen). © These attributes can be powered with external data series. The data transfer is done via a Bluetooth radio link. Optionally, the triggering of a measurement via a soft key from within the software is possible, a "blurring" is no longer possible and a more accurate measurement can be performed. The software FMcapture can be used by multiple users / projects separately. Furthermore a password protection is also available. You can use a desktop PC, a notebook or a tablet PC as hardware. You get the software FMcapture on CD / DVD, here you can find the setup with the following options: Install, Repair, and Remove. The user manual is also included on the disc. Please always run the setup options from this original disk and always store all updates as a backup. You will be informed about potential changes per e-mail-newsletter or you search for current © information and updates for the software FMcapture under „www.grote-software-systems.de“. You can assign all measurements to individual projects. The name and location of the data files can be chosen freely or use the default parameters. You can see all recorded data at a later date, change attributes, print data in different formats, delete individual data or you can export measurement data. Many choices, locations or information requests are user adjustable. Here, you can also rely on their own data files and templates. Furthermore you can create and manage user profiles and different other things. All settings and attributes for the user are saved here. The company Grote Software Systems is not liable for performance issues, failures or data loss of any kind. Please store your manual carefully. The hereby marked passages are important instructions in the manual! 1.1 Copyrights and Trademarks The following brands are subject to copyright protection and are protected by national / international rights: © FMcapture is a trademark from the company Grote Software Systems. DISTO™ is a trademark of Leica Geosystems GmbH. © Bluetooth is a worldwide registered trademark of Bluetooth SIG, Inc. Microsoft® Windows® XP, Microsoft® Windows Vista®, Microsoft® Windows® 7 and Microsoft® Windows® 8 are a worldwide registered trademark of the Microsoft Corporation. Microsoft® Excel® is a worldwide registered trademark of the Microsoft Corporation. 4 Version 3.0.12.1 03/31/2013 Grote Software Systems 2 System Requirements 2.1 Desktop-PC, Notebook and Tablet-PC Processor: Main memory: HDD-memory: Drive: Graphic card: Operating system: Add-ons Software: (*1) 800Mhz or better 128MB or better 20GB or better CD/DVD-drive 256MB or better Microsoft® Windows® XP Microsoft® Windows Vista® Microsoft® Windows® 7 Microsoft® Windows® 8 (except Windows® 8 RT) © (*1) Bluetooth -adapter Microsoft® .Net Framework 3.5 installed and / or activates Microsoft® Excel® (Version 2005-2010) Microsoft® Office 2005-2010 (with installed Excel®) Not included 5 Version 3.0.12.1 03/31/2013 Grote Software Systems 3 Installation / Setup Options 3.1 Installation © The installation of FMcapture is generally issued in two separate operation steps. The installation process is divided into two sections, the first manages the license request and the second installs the actual program. This requires that you run the setup for two times! The license request is made through a license request file, which you will receive during the setup. This license request file must be sent by e-mail to the following email address: [email protected] Note: Please use your default e-mail program. You cannot send an e-mail from this setup. Within 24 hours of the request for a license, you get via e-mail to the specified email address your corresponding license file. Note: The license request can only be processed on working days. Short delays are possible. After receiving your license file, please save this into the folder ... \ FMcaptureKey or at the corresponding location which you choose! 3.1.1 First Segment – License Request For implementation of the first segment insert the original data medium in the CD/DVD drive and start the file Setup.exe in the folder Setup_FMcapture. For Windows Vista®, Windows® 7 und Windows® 8 you have to consider the user account control, please always implement the file Setup.exe as administrator and allow the program to start explicitly. If you are not the administrator and you do not possess the appropriate authority, these requirements have to be ensured before the setup. Setup.exe Unknow Hard drive on this computer Windows Vista®,Windows® 7 Windows® 8 The setup-program is started. After some short information you are requested for a range of language settings first. Note: The standard language setting at the first time is English! All available languages are offered at choice. Further languages can be ordered as option and can be added, but in return additional costs arise. 6 Version 3.0.12.1 03/31/2013 Grote Software Systems Please implement the setup step by step now and end the setup after the creation of the license request file. Please read and accept the license agreement and the conditions of use (set hooks for these) and click Next. Please insert the requested data in the next window and click Next, too. As a next step choose the archive location for the license request file and click Next. The license request file is created and deposed in the previous chosen memory path. Close now the first segment with Exit. 7 Version 3.0.12.1 03/31/2013 Grote Software Systems Program: Setup.exe Publisher: Unknow Location: Hard drive on this computer If you get this message after the finish of the setup please confirm by “The program is not installed correctly.” You can always interrupt the setup in the first segment with cancel. You always get back to the previous step by back/previous. Please send the license request file via email after the finish of the first segment to the following email address: [email protected] Advice: Please use your standard email program for that. You cannot send the email from the setup. 3.1.2 Second Segment – Program Installation For the implementation of the second segment insert the original data medium in the CD/DVD drive and start the file Setup.exe in the folder Setup_FMcapture (also see 3.1.1)! For Windows Vista®, Windows® 7 und Windows® 8 you have to consider the user account control, please always implement the file Setup.exe as administrator and allow the program to start explicitly. If you are not the administrator and you do not possess the appropriate authority, these requirements have to be ensured before the setup. The setup program is started. After short information you are requested to load the license file. 8 Version 3.0.12.1 03/31/2013 Grote Software Systems Please implement the setup step by step now and end the setup after the installation. First you have to load the license file which you got via email and continue the installation with Next. As a next step confirm the installation with Next. Now you can choose the archive location for your installation (recommendation: directly under the drive e. g. c: \). Please choose the display size according to the used PC system. This setting can be changed after the installation as well. Furthermore you can choose if an icon should be shown on the desktop for a quicker start of the program. The installation is started with Next. The setup can be completed with Exit after a successful installation of © FMcapture You can always interrupt the setup in the second segment with Cancel. You always get back to the previous step by Back/Previous. 3.2 Repairing © If problems with the software FMcapture should occur or the program does not work as usual, you can let the software installation be repaired through Setup. For implementation of the second segment insert the original data medium in the CD/DVD drive and start the file Setup.exe in the folder Setup_FMcapture. For Windows Vista®, Windows® 7 und Windows® 8 you have to consider the user account control, please always implement the file Setup.exe as administrator and allow the program to start explicitly. If you are not the administrator and you do not possess the appropriate authority, these requirements have to be ensured before the setup. The setup program is started. After short information you are conducted to the choice of setup-options. Choose Repair and start the repairing with Next. 9 Version 3.0.12.1 03/31/2013 Grote Software Systems You can close the setup with Exit after successful reparation. The program can be used as usual now. If nevertheless problems should arise contact the support. 3.3 Uninstall © O n l y use the setup of FMcapture for uninstall. An uninstall of your system can only be assured in this way. For implementation of the second segment insert the original data medium in the CD/DVD drive and start the file Setup.exe in the folder Setup_FMcapture. For Windows Vista®, Windows® 7 und Windows® 8 you have to consider the user account control, please always implement the file Setup.exe as administrator and allow the program to start explicitly. If you are not the administrator and you do not possess the appropriate authority, these requirements have to be ensured before the setup. The setup program is started. After short information you are conducted to the choice of setup-options. Choose Remove and start uninstall with Next. © Setup checks the installation of FMcapture now and implements uninstall. While doing that you are asked again © if you really want to remove FMcapture from your system. 10 Version 3.0.12.1 03/31/2013 Grote Software Systems Furthermore you have the possibility to save your measured data before uninstall. After these two queries uninstall is implemented. This process can last a moment. Please do not implement any operations at your system during that time! © You can close the setup with Exit after successful implementation. FMcapture is removed from your system with all components and settings now. 11 Version 3.0.12.1 03/31/2013 Grote Software Systems 4 Program handling 4.1 Program start © The software FMcapture 3.0 can be started from the installation file on FMcapture30.exe via double-click. For the used option for desktop-symbol the start happens directly from the desktop linkage via double-click. © As a further option you can also find FMcapture 3.0 under programs and you can start it here via double-click, too. In Windows® 8, a tile is placed on the home screen for disposal. ® ® ® For Windows Vista , Windows 7 Windows 8 you have to permit the application of FMcapture30.exe explicitly. MFcapture30.exe Unidentified Publisher FMcapture30.exe Unknow Hard drive on this computer Windows Vista®,Windows® 7 Windows® 8 After starting for about 3 seconds, an info window will appear (Splash), then you will go for the user control. Here the last user / project or FMcapture as factory setting (default at the first start) are displayed. For continuation of the program, a password entry is required. The factory setting (default at the first start) is the password: 11111 , otherwise the respective password for the user / project input. If a user / project is created without a password, in this step, no password entry is required. After reviewing your information of the user control you will be redirected to the Start Menu. 4.2 Start Menu © The start menu offers the choice of all functions of FMcapture . Note: Please configure your program under 4.8 Settings first! 12 Version 3.0.12.1 03/31/2013 Grote Software Systems The following menu items are available: 4.3 Data Recording Data Data Export Info Help Settings Exit Data Recording At Data Recording you can record measurements and annotate them with appropriate attributes. The specific measurement modes (catenary height, catenary position, distance to PLE (PoleLeadingEdge) and catenary wear out) can be used optional or separately. The connection to your catenary measuring instrument is shown in the status bar below, you will be informed about the used com-port, the serial number, the fitted Disto™ and about the connection type. You will be informed about the options during the measurement through the plain text display at the info bar in the middle of the window. In the top of the status bar you can see the data connection status with the catenary measuring instrument. The Softkey measurement is displayed. The "Remote Control On" is then displayed in red. A visual description shows you the fundamental function of the chosen mode as a help. You can use the predefined file path and file names or you change these settings with Save As in compliance with your wishes. 13 Version 3.0.12.1 03/31/2013 Grote Software Systems The predefined measurement file has got the following structure: FM 01 31 A 19 . fmd file extension (fmd = FMcaptureData) hours (1 to 24) index for number of measurement files per hour (A to Z) day month index for measurement mode: - FM… catenary measurement Now you can describe your measuring object. For this purpose there are up to three attribute fields available. You can set these on your own under Settings -> Attributes or you adopt the standard setting with object, location and note. Look at 4.8 Settings for that! Note: Minimum one attribute has to be contracted for continuing with the data recording. You can choose list entries or make entries directly with a dropdown-menu in all attribute fields. The source and dwelling time of list entries are freely configurable for every attribute field. Look at 4.8 Settings -> Data Recording and Attributes for that! Start the data recoding with Start after the input of one attribute. You can close the measurement file with Cancel at this point, with Previous you leave the data recording without creating a measurement file. After call of the function data recording the first data from the catenary measuring system are already read and shown (track gauge, catenary wire type and device temperature). After the first start the measurement file is set up and the first dataset is opened. You can use the correlated measurement modes now. Note: The measurement modes can be used total or separately for every dataset! An order is not relevant here. A navigation of the data collection for the current mode happens through the related softkeys. The available functions for the datasets are shown via the softkeys under the picture area. The resolution of the measurement via software happens through the softkey Measurement and the choice of options below. Basically you can run every single measurement per dataset as often as you like, only with softkey Save under the picture area the measured data is saved and matched to the definite dataset. After saving a dataset the program goes to the next dataset automatically, this is shown by a number counter. 14 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.3.1 Measurement - Catenary height With the soft key Height you start the measurement of the height of the catenary. In the remote mode just one measurement is triggered, in the multi-mode it is measured as long as the softkey Measurement is activated again. Without the option of the remote operation, you have to make the actual measurement and data transmission at the catenary measuring system. The measurement of the inclination shows the banked track axis (camber). Note: If the option tilt correction under Settings is selected, an angle icon appears next to the measured value. The measured value is corrected in relation to the slope of the transverse axis and is saved. With the softkey Save you stop the measurement of the catenary height and insert the data into the data buffer of the software. You can now perform the measurements in the other measurement modes. You can take a new measurement of the catenary height at any time, before you save the record. Now you can, even if no further measurement mode has been used, save the record finally yet and jump automatically to the next record. This process cannot be cancelled! 15 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.3.2 Measurement - Catenary position With the softkey Position you start the measurement of the catenary position. In the remote mode just one measurement is triggered, in the multi-mode it is measured as long as the softkey Measurement is activated again. Without the option of the remote operation, you have to make the actual measurement and data transmission at the catenary measuring system. The measurement of the inclination shows the banked track axis (camber). With the softkey Save you stop the measurement of the catenary position and insert the data into the data buffer of the software. You can now perform the measurements in the other measurement modes. You can take a new measurement of the catenary height at any time, before you save the record. Now you can, even if no further measurement mode has been used, save the record finally yet and jump automatically to the next record. This process cannot be cancelled! 16 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.3.3 Measurement - Distance to PLE (PoleLeadingEdge) With the softkey PLE you start the measurement of the distance of the catenary / track axle to the fattening front edge of the catenary pole. In this case, depending on the option selected in Settings, the distance from the catenary position or the track center to the front edge of the catenary pole is measured (in the target direction of the laser). For the opposite catenary the catenary measuring system has to be rotated by 180 °. In the remote mode just one measurement is triggered, in the multi-mode it is measured as long as the softkey Measurement is activated again. Without the option of the remote operation, you have to make the actual measurement and data transmission at the catenary measuring system. The measurement of the inclination shows the banked track axis (camber). Note: If the option tilt correction under Settings is selected, an angle icon appears next to the measured value. The measured value is corrected in relation to the slope of the transverse axis and is saved. With the softkey Save you stop the measurement of the distance PLE and insert the data into the data buffer of the software. You can now perform the measurements in the other measurement modes. You can take a new measurement of the catenary height at any time, before you save the record. Now you can, even if no further measurement mode has been used, save the record finally yet and jump automatically to the next record. This process cannot be cancelled! 17 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.3.4 Measurement - Catenary wear out In the measurement of the catenary wear out the following procedure is carried out: With the catenary measuring systems, the distance between the left edge and the right edge of the tendon is measured at the bottom of the contact wire. Out of this the wear out is computed as a measurement value and a percentage value is investigated according to the set catenary type. The distance of the catenary measuring systems to the catenary is not directly relevant (minimum distances must be observed, however, according to the manufacturer description). You can use the catenary measuring systems from the track level. It is also possible to use the catenary measuring systems mounted on a service vehicle (tower wagons, manlift, ...). Note: The accuracy of the catenary measuring system has to be adjusted here at "0.0 inch"! With the softkey Wear out you start the measurement of the catenary wear out. First the left tendon edge is measured. You can make the laser-pointer visual via the softkey Marker On/ Off to find the exact position of the tendon on the left edge. In the remote mode just one measurement is triggered, in the multi-mode it is measured as long as the softkey Measurement is activated again. Without the option of the remote operation, you have to make the actual measurement and data transmission at the catenary measuring system. With the softkey Tendon left you save this value into the data buffer of the software. 18 Version 3.0.12.1 03/31/2013 Grote Software Systems At second, the right tendon edge is measured with the softkey Tendon right. You can make the laser-pointer visual via the softkey Marker On/ Off to find the exact position of the tendon on the left edge. In the remote mode just one measurement is triggered, in the multi-mode it is measured as long as the softkey Measurement is activated again. Without the option of the remote operation, you have to make the actual measurement and data transmission at the catenary measuring system. With the softkey Tendon right you save this value into the data buffer of the software. Now the catenary wear out is calculated and the values are displayed accordingly. With the softkey Save you stop the measurement of the catenary wear out and insert the data into the data buffer of the software. Now you can perform the measurements in the other measurement modes. You can take a new measurement of the catenary height at any time, before you save the record. Now you can, even if no further measurement mode has been used, save the record finally yet and jump automatically to the next record. This process cannot be cancelled! After saving the record you can enter the attributes for the next record and to start the next measurement. The steps 4.3.1 to 4.3.4 can now be repeated continuously. With Close you close and save the current Data file. The next data file can now be created. With Back the current data file is saved and Data Record will be closed. 19 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.4 Data The menu Data allows you to select data from a data file to view, change or delete data attributes. At the same time you have the opportunity to output individual datasets or the entire data file to a printer. Note: Under Settings -> Data, you have to make corresponding configurations for these functions. Look at 4.8 Settings for that! First you need to select a data file. To do this, click Open! Now you can select a folder from your project and mark a data file. Double-click the file or open the file with Open. The data file is loaded, the file path and file name are displayed. The total number of datasets and the current number of measurement data are displayed in the right pane. With using the buttons and you can navigate between your datasets. Depending on the configuration under Settings -> Data now you can edit all attributes. For this purpose, the same selections and input options are available which are described under 4.3 Data Recording. Note: If the option tilt correction under Settings is selected, an angle icon appears next to the measured value. The measured value is corrected in relation to the slope of the transverse axis and is saved. Similarly, you can delete individual data sets. For this purpose, this function must be released under Settings -> Data. If this is the case, the Delete button is available. You will be asked explicitly, if you really want to delete the dataset. Caution: Deleted data records are lost forever and cannot be restored! By Save, you can save the opened file manually with all current changes. The file is not closed in this case. 20 Version 3.0.12.1 03/31/2013 Grote Software Systems Depending on the configuration, you have the option of spending data to a printer via the button Print. For this purpose, click the softkey Print, choose printing options, click (as Settings or from settings of this choice) and click softkey Print again. You will see the printer menu and you can still make adjustments and / or execute the print. With Close the open data file is closed. When you have not saved manually, you are prompted for it now. All current changes are saved only with the button Yes. 21 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.5 Data Export The Data Export function allows you to export data to a data file in different formats. Here you can export the complete data file. You can use a program specific format or you can determine the individual data entries and the order itself. You can export with the following formats: - Text-file (.txt), separator here freely selectable - Excel®-file 2005-2010 (.xlsx) - CSV-file (.csv) First you need to select a data file. To do this, click Open! Now you can select a folder from your project and mark a data file. Double-click the file or open the file with Open. From this loaded data file, the file path and file name are displayed. With Back you quit the function Data Export, all selected export settings are not saved. Next, you can load an existing export setting, a default setting (FMcaptureExport) is always available. By clicking on the individual measurement buttons you can build your own export format. With the Undo button, you can always choose a step back. An exception is, however, the button All , this allows you to select all data of the measurement entries. If your choice doesn`t match your ideas you can set them back at any time by deleting it and then make a new selection. You can also choose the various status data. 22 Version 3.0.12.1 03/31/2013 Grote Software Systems With Apply the chosen setting for the measurement items is accepted. In the next step you need to set the export format. This selection can be changed at any time before the actual export. After setting the export format the name for the export file is displayed. It is always the name of the open FMcapture data file. The extension corresponds to the selected export format. You can specify your own file name. You can simply overwrite the suggested file name. At the same time the file path is displayed. By default, the location of the file path is always the Export folder in © the installation path of FMcapture . The user export folder is created at the first time exporting data. If you want to choose a different location, you can make your own selection with Save As. For the export format text file, you can also change the name of the file extensions, here also just overwrite the existing entry. At the same time you have the ability to change the separator. 23 Version 3.0.12.1 03/31/2013 Grote Software Systems For the export format Excel ® file, 2005-2010 (left) and for the export format CSV (right) you can only change the file name. If you have chosen your export settings, the data file is exported with Start. You can then save the selected export settings under its own label to load them again. For this, after entering a name, click Save. Note: You find a list of all export settings, see Settings -> Data Export, here you can also remove items from the list. Look at 4.8 Settings for that! After export you can close the open data file with Close. You can leave the Data Export with Back. 24 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.6 Info Under Info you will be informed shortly about the version of the software as well as about the licensee, license © number and the serial number of your FMcapture installation. At the same time you see the note to the rights of the company Grote Software System. Also a note to all used trademarks is displayed. With close you leave the info area. 4.7 Help © To assist the software FMcapture , this user manual is available as PDF file. You can start this manual under Help. © You can also find the manual in the installation folder from FMcapture under FMcapture -> Manual named FMcapture_3_Manual_002.pdf. Note: The current version of the user guide can be found at the following website: http://www.grote-software-systems.de/ under Download -> FMcapture -> Manual 25 Version 3.0.12.1 03/31/2013 Grote Software Systems 4.8 Settings In Settings you can set various preferences. These settings will be taken when leaving the menu Settings with the button Back. © Note: After installing the program FMcapture some settings must be configured! © You can save all settings, the list of entries, attributes and the export settings on the user control of FMcapture . In the delivery condition the user FMcapture is set up as a user, the same user is also set up in return to the factory setting. Tab Data Recording In the register Data Recording, the following options for the 3 attribute fields are available: Content from external file read! If this option is selected, the list for the attribute field from an external file is copied, which you can load under the Attributes tab. Note: This option is only enabled when the files are loaded. Content at the end of program delete! This option is only available for attributes, which have lists from internal FMcapture files. Add new content! If this option is chosen new attributes are added both in internal and external lists. Tab Data 26 Version 3.0.12.1 03/31/2013 Grote Software Systems On the tab Data, you can configure the following options: Delete If this item is selected, you can delete individual datasets. Edit Here you can edit the attribute fields. Print You can choose the printing options here. The following options are available: - printout a list - printout a datasheet - printout of the current dataset - printout all datasets Tab Data-Export On the tab Data Export you have the possibility to view a list of all saved export settings. At the same time, you can delete individual export settings which have been created by users. Note: Attention! All export settings will be deleted, also of the not accounted user! Tab Attribute Description by user Via the tab Attributes you can load one file for an attribute field. The file is the data source for the appropriate attribute field. So it is necessary to represent all the contents of this file line by line and only as text format. These files have to be available in the format of text files (txt). 27 Version 3.0.12.1 03/31/2013 Grote Software Systems With Load you can search through the browser for your desired file and upload with a double-click or open it with Open. You can assign all three attributes to the files independently. Description by user Furthermore you have the option to give each of the three attributes a specific name in this tab. For this purpose just tick description by user. If you do not use this option, FMcapture © uses the default name object, location and comment. Tab Com port Under the tab Com port you can configure the COM port. All settings for the catenary measuring system (DISTO ™) series have been configured by the setup, only the COM port still has to be selected. For this purpose all available COM port (not only physical ports) are displayed in this selection field. Select the appropriate COM port for your connection to the catenary measuring system. 28 Version 3.0.12.1 03/31/2013 Grote Software Systems Tab User Under the tab User you have the option to assign your current settings to a corresponding user profile or to load an already existing user profile or to delete one of these. To save your settings enter a user name in the appropriate field and save it. If the username is already used you will be alerted and can choose whether you want to overwrite it or choose a different username. You can choose a password or you can create a user without a password. When you choose a user with a password, you must write the password in both fields. To load a user profile, select from existing users of the entry and with Store this user profile is applied. A security query prevents accidental overwriting of the current user profile. If the user is loaded, the user name will be adjusted accordingly. If the user is created with a password, you have to write the password in the field. To delete a user, select the user name and enter the password, after a safety query now you can delete the user. Attention: This process cannot be undone! Note: If the user is created without password protection eliminates the input of the password, when a user is loaded or deleted! Tab Catenary / Rail Under the tab Catenary / Rail all basic values for the calculations on the catenary and rail are determined. You can choose the catenary type, the sign of the catenary determine (sine, ZigZag) and select a track gauge. You can enter an own track gauge. Attention: All values of catenary and rail are in mm! Note: This data is used during data recording for all calculations. All this values cannot be changed there! 29 Version 3.0.12.1 03/31/2013 Grote Software Systems Tab Device Under the tab Device all basic values for the measurement are set. You can specify the offset for height measurement (Y-axis) and position measurement (x-axis). Please pay attention to the details for the relevant catenary measuring system. You can choose the unit systems, you can activate/deactivate the remote control and choose a tone when receiving data. You can also choose a height correction. 4.9 Finishing © You can close FMcapture in two different ways. Once with Exit in the Start Menu and the other with the Windows® close button ! 5 Troubleshooting / Hotline © If you receive an error message while starting FMcapture or the program does not run properly, it indicates that the installation files are deleted accidentally or they are defective. © In that case run a repair from the setup of FMcapture as described in 3.2. Repair. If the error still occurs, please contact the hotline including the following information: information about the operating system license number serial number any error code error description your contact details Please send your request only via e-mail to: [email protected] Upon receipt of your email, you will receive an answer immediately or we will call you. 30 Version 3.0.12.1 03/31/2013 Grote Software Systems 6 Imprint © Each version of FMcapture is a single user version. It is not allowed to copy, distribute or sell it in any other form to third parties without the consent of the company Grote Software System. All rights to the software © © FMcapture , logos, icon or other publications on software FMcapture are protected by copyright for the company: Grote Software System, 28832 Achim - Germany. Reproductions in any form are not allowed to be done without the explicitly written permission of Grote Software System. Grote Software Systems Am Kösterhof 10 28832 Achim Germany e-mail internet [email protected] www.grote-software-systems.de Copyright (©) 2013 Grote Software Systems 31 Version 3.0.12.1 03/31/2013 Grote Software Systems 32 Version 3.0.12.1 03/31/2013
