Download cfd-v15

CFD-V15/V24
SERVICE MANUAL
US Model
Canadian Model
Ver 1.1 1998. 08
CFD-V15
With SUPPLEMENT 1 (9-923-320-81)
With SUPPLEMENT 2 (9-923-320-82)
AEP Model
UK Model
CFD-V24
E Model
CFD-V15/V24
Photo : CFD-V15
Model Name Using
CD Section
NEW
Similar Mechanism
Tape Section
CFD-V10
Optical Pick-up Type
KSM-213CDM
Tape Transport Mechanism Type
MF-V10-117
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
With 3.2-ohm, loads, both channels driven from 150 – 10,000 Hz ; rated
2W per channel-minimum RMS power, with no more
than 10% total harmonic distortion in AC operation. (US model)
Aerials
Other Specification
CD player Section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration : Continuous
Laser output : Less than 44.6 µW
(This output is the value measured at a distance of about 200
mm from the objective lens surface on the optical pick-up
block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 – 20,000 Hz +1 /–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM : 87.6 – 108 MHz (US, Canadian,
Central & South America, E, Singapore model)
87.6 – 107 MHz (AEP, UK, Saudi Arabia,
Russian model)
87.5 – 108 MHz (Italian model)
65 – 108 MHz (East European model)
MICROFILM
AM : 530 – 1,710 kHz (US, Canadian, Central & South
America model)
531 – 1,602 kHz (Singapore, E, Saudi Arabia, AEP,
UK, East European, Russian model)
526.5 – 1,606.5 kHz (Italian model)
FM: Telescopic aerial
AM : Built-in ferrite bar aerial
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 – l0,000 Hz
General
Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2)
Outputs Headphones jack (stereo minijack)
For 16 – 68 ohms impedance headphones
Power output (excluding US model)
2.3 W + 2.3 W (at 3.2 ohms, 10% harmonic distortion)
– Continued on page 2 –
CD RADIO CASSETTE-CORDER
TABLE OF CONTENTS
Power requirements
For CD radio cassette-corder
120V AC, 60Hz (US, Canadian, Central & South America
model)
230V AC, 50Hz (AEP, UK, Italian, East European, Russian,
Singapore model)
110 – 120V, 220 – 240V AC selectable 50/60Hz (E, Saudi
Arabia model)
9V DC, 6 size D (R20) batteries
Power consumption
AC 20 W
Battery life
For CD radio cassette-corder :
FM recording
Sony R20P : approx. 13.5 h
Sony alkaline LR20 : approx. 20 h
Tape playback
Sony R20P : approx. 7.5 h
Sony alkaline LR20 : approx. 15 h
CD playback
Sony R20P : approx. 2.5 h
Sony alkaline LR20 : approx. 7 h
Dimensions
Approx. 425 x 160 x 246 mm (w/h/d)
(16 3/4 x 6 3/8 x 9 3/4 inches) (incl. projecting parts)
Mass
Approx. 4.0 kg (8 lb. 13 oz) (incl. batteries)
Supplied accessories
AC power cord (1 )
Specifications ........................................................................... 1
1. SERVICING NOTES .................................................... 3
2. GENERAL
Location and Function of Controls .................................... 4
3. DISASSEMBLY
3-1. Front Cabinet, Contorl Board Removal ......................
3-2. Power Board, AC Inlet Board,
BATT Board, VOL SEL Board Removal ...................
3-3. Upper Cabinet Removal .............................................
3-4. Optical pick-up Section, Mechanism Deck,
Main Board, REC SW Board, CD Motor Board,
MONO/ST SW Board Removal ................................
5
5
6
6
4. DIAL POINTER INSTALLATION ............................ 7
5. ADJUSTMENTS
5-1. Mechanical Adjustments ............................................ 8
5-2. Electrical Adjustments ................................................ 8
6. DIAGRAMS
6-1. Explanation of IC Terminals ...................................... 11
6-2. Block Diagrams ........................................................ 13
6-3. Printed Wiring Boards .............................................. 17
6-4. Schematic Diagram (Main Section) ......................... 21
6-5. Schematic Diagram (CD Section) ............................ 25
Design and specifications are subject to change without notice.
7. EXPLODED VIEWS
CAUTION
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
7-1. Front Cabinet Section ...............................................
7-2. Upper Cabinet Section ..............................................
7-3. Rear Cabinet Section ................................................
7-4. Mechanism Deck Section (1) ...................................
7-5. Mechanism Deck Section (2) ...................................
7-6. Optical pick-up Section ............................................
Laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
This Compact Disc player is
classified as a CLASS 1 LASER
product.
The CLASS 1 LASER
PRODUCT label is located on
the rear exterior.
32
33
34
35
36
37
8. ELECTRICAL PARTS LIST ................................ 38
MODEL IDENTIFICATION
– Model Number Label –
MODEL NO.
SAFETY-RELATED COMPONENT WARNING!!
CFD-V15
CFD-V24
CD RADIO CASSETTE-CORDER
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
US, Canadian,
Central & South America model : AC120V ⁄60Hz
AEP, UK, Italian, East European, Russian,
Singapore model
: AC230V ⁄50Hz
E, Saudi Arabia model
: AC110 – 120V , 220 – 240V
selectable. ⁄ 50/60Hz
–2–
SECTION 1
SERVICING NOTES
SAFETY CHECK-OUT
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
After correcting the original service problem, perform the
following safety check before releasing the set to the customer :
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75V,
so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled
with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode
emission, observe more than 30 cm away from the objective
lens.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig : X-4918-255-1
To Exposed Metal
Parts on Set
0.15 µF
1.5kΩ
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Press CD open knob.
2. Open the lid for CD.
3. Push on SWITCH (S801) as following figure.
4. Confirm the laser diode emission while observing the
objecting lens. When there is no emission, Auto Power
Control circuit or Optical Pick-up is broken.
Objective lens moves up and down once for the focus
search.
Insert a precision
screw driver and push
SWITCH (S801)
–3–
SECTION 2
GENERAL
LOCATION AND FUNCTION OF CONTROLS
MAIN UNIT
1
4
5
2
!™
6 7 8 9 0 !¡
1 Tape operation buttons
2 CD operation buttons
≠ button
± button
PLAY MODE button
DISPLAY/ENTER button
fl button
p button
3 OPEN / CLOSE button
4 Information display
5 MEGA BASS switch
6 2 Phones jack
7 VOL knob
8 TONE knob
9 OPR / BATT indicator
!º FUNCTION switch
!¡ TUNE knob
!™ FM MODE switch
(AEP, UK, Italian, East European, Russian model)
–4–
3
SECTION 3
DISASSEMBLY
r
The equipment can be removed using the following procedure.
Set
Front cabinet
Rear cabinet
Control board
E, Saudi Arabia model
Power board, AC inlet board, BATT board, VOL SEL board
Upper cabinet
Main board, CD motor board
Optical pick-up section
REC SW board
Mechanism deck
MONO/ST SW board
AEP, UK, Italian, East European, Russian model
Note : Follow the disassembly procedure in the numerical order given.
3-1. FRONT CABINET, CONTROL BOARD REMOVAL
4 Knob, VOL
Front cabinet
Control board
6 Screws +BVTP (2.6X8)
7
1
2
5
3 Screws +BVTP (3X14)
Rear cabinet
3 Screws +BVTP (3X14)
3-2. POWER BOARD, AC INLET BOARD, BATT BOARD, VOL SEL BOARD REMOVAL
3
BATT board
4
AC inlet board
2
Power board
1 Screws +BVTP (3X10)
VOL SEL board
5 Screws +BVTP (3X10)
E, Saudi Arabia model
–5–
Rear cabinet
3-3. UPPER CABINET REMOVAL
2 PUSH OPEN/CLOSE
3 Screws
+BVTP (3X10)
4 Screws +BVTP (3X10)
Upper cabinet
2
Handle
1 STOP/EJECT
6
7
5
Rear cabinet
3-4. OPTICAL PICK-UP SECTION, MECHANISM DECK,
MAIN BOARD, REC SW BOARD, CD MOTOR BOARD, MONO/ST SW BOARD REMOVAL
8 Remove solder
5 Screws +BVTP (3X10)
CD motor board
9
Mechanism deck
Optical pick-up
section
7 Screws +BVTP (3X10)
3 Wire (Flat type) (16 core)
to MAIN board (CNP702)
6
REC SW board
2 CNP707 (6pin)
1
AEP, UK, Italian,
East European, Russian model
!º Screw +BVTP (3X8)
MONO/ST SW board
Main board
4
Rear cabinet
–6–
SECTION 4
DIAL POINTER INSTALLATION
Note : Follow the installation procedure in the numerical order given.
1Align the pointer with the groove of front cabinet and insert it as shown in the illustration.
2Align knob (TU) with front cabinet and fasten the screw.
Front cabinet
1 Pointer
Knob (TU)
2 Screw +BVTP (2.6x8)
3Turn the knob (TU) fully in the direction of the allow as shown in the illustration.
4Turn the tuning capacitor gear fully in the direction of the allow as shown in the illustration.
5Fasten the front cabinet and rear cabinet with the screws.
Front cabinet
5
Rear cabinet
4 Tuning capacitor gear
3 Knob (TU)
–7–
SECTION 5
ADJUSTMENTS
5-1. MECHANICAL ADJUSTMENTS
Adjustment Value :
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head
pinch roller
erase head
rubber belts
capstan
2. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase
head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
Speed checker
–1 to +1%
Digital frequency counter
2,970 – 3,030Hz
Frequency difference between the beginning and the end of the tape
should be within 1.5% (45Hz).
Adjustment Location :
Torque Measurement
Torque
Torque Meter
Forward
CQ-102C
Forward
Back Tension
CQ-102C
Fast Forward
CQ-201B
Rewind
CQ-201B
Meter Reading
30 – 70 g•cm
(0.42 – 0.97 oz•inch)
1.5 – 5.5 g•cm
(0.020 – 0.076 oz•inch)
more than 60 g•cm
(more than 0.84 oz•inch)
more than 60 g•cm
(more than 0.84 oz•inch)
Tape Tension Measurement
Torque Meter
Tape speed adjustment
control inside motor
Meter Reading
more than 100g
(more than 3.53 oz)
CQ-403A
TUNER SECTION
AM Section
Function switch : AM
Volume
: MIN
5-2. ELECTRICAL ADJUSTMENTS
TAPE RECORDER SECTION
Standard Output Level
Output terminal
load impedance
output signal level
AM RF signal
generator
HP OUT
32 Ω
0.25V (–10dB)
Test Tape
Type
WS-48A
Signal
3kHz, 0dB
Put the lead-wire
antenna close to
the set.
30% amplitude modulation by 400Hz
signal.
Output level : as low as possible
Used for
Tape Speed Adjustment
0dB = 0.775V
FM Section
Function switch : FM
Volume
: MIN
Tape Speed Adjustment
Procedure :
Mode : Playback
FM RF signal
generator
0.01µF
speed checker
LFM-30 or
digital frequency
counter
test tape
WS-48A
(3kHz, 0dB)
22.5kHz frequency deviation by
400Hz signal.
Output level : as low as possible
32Ω
set
level meter
32Ω
J301 (phones)
set
J301 (phones)
–8–
telescopic
antenna
terminal
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
<
<<
[
((
VCO Adjustment
Procedure :
FM RF signal
generator
telescopic
antenna
terminal
> : AEP, UK, Singapore, Russian model only
>>: East European model only
] : Italian model only
)) : Saudi Arabia model only
0.01µF
set
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T2
455kHz
AM FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
L4
520kHz
[516kHz]
((516kHz))
1,780kHz
<1,680kHz> <<1,680kHz>>
CT4
[1,630kHz]
((1,630kHz))
Carrier frequency : 98MHz
Modulation : No modulation
Output level : 1.38mV (–55dB)
1. Connect the frequency counter to 4 and 7 pin of IC 1 as
shown the figure below.
2. Turn the set to 98MHz.
3. Adjust RV1 for 76kHz±500Hz reading frequency counter.
[ MAIN BOARD] (Conductor side)
frequency counter
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L3
620kHz
CT3
1,400kHz
1µF
33kΩ
IC 1
FM IF ALIGNMENT
Adjust for a maximum reading on level meter.
T1
10.7MHz
30
1
R6
4
FM FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
86.5MHz
<87.0MHz>
<<64.0MHz>>
L2
[87.35MHz] ((87.35MHz))
109.5MHz <108.3MHz>
[108.25MHz]
CT2
((107.8MHz))
7
C14
C15
16
15
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
86.5MHz
<87.0MHz>
<<68.0MHz>>
L1
[87.35MHz] ((87.35MHz))
109.5MHz <102MHz>
[108.25MHz]
CT1
((107.8MHz))
Adjustment Location : Main board (See page 10)
Adjustment Location : Main board (See page 10)
How to put the set into CD Test Mode
1. Set the function switch to power off.
2. Set the function switch to CD while
≠ key and p key pressing.
The set is into CD test mode (88 is displayed).
3. Turn the power off to release test mode.
–9–
Adjustment Location
[MAIN BOARD]
(Component side)
T1 : FM IF Alignment
L3 : AM Tracking Adjustment
L4 : AM Frequency Coverage Adjustment
RV1 : VCO Adjustment
L1 : FM Tracking Adjustment
L2 : FM Frequency Coverage Adjustment
T2 : AM IF Alignment
CT4 : AM Frequency Coverage Adjustment
[MAIN BOARD]
(Conductor side)
CT2 : FM Frequency Coverage Adjustment
CT1 : FM Tracking Adjustment
CT3 : AM Tracking Adjustment
– 10 –
SECTION 6
DIAGRAMS
6-1. EXPLANATION OF IC TERMINALS
IC702 CD DIGITAL SIGNAL PROCESSOR, LED DRIVE, SYSTEM CONTROL (CXP401-601R)
Pin No.
Pin name
I/O
1
SEIN
I
Description
CD SENS input.
2
CNIN
I
CD SENS input.
3
DATO
O
CD DSP command data output.
4
XLTO
O
Latch output.
5
CLKO
O
Clock output for CD DSP command.
6
DVSS
–
Digital ground.
7
DVDD
–
Digital power supply (+5V).
8
MON
–
Not used (Open).
9
MDP
O
Spindle motor drive control.
10
MDS
–
Not used (Open).
11
LOCK
O
Lock signal output.
12
VPCO2
–
Not used (Open).
13
VPCO1
–
Not used (Open).
14
VCKI
–
Not used (Connect to !∞ pin).
15
V16M
–
Not used (Connect to !¢ pin).
16
VCTL
–
Not used (“H” level).
17
PCO
O
Decoder PLL phase comparator output.
18
FILI
I
Decoder PLL filter input.
19
FILO
O
Decoder PLL filter output.
20
AVSS
–
Analog ground.
21
CLTV
I
Decoder PLL VCO control voltage input.
22
AVDD
–
Analog power supply (+5V).
23
RF
I
CD RF signal input.
24
BIAS
I
Playback EFM asymmetry current constant input.
25
ASYI
I
Playback EFM asymmerty comparater voltage input.
26
ASYO
O
Playback EFM full swing output.
27
TEST1
I
Test terminal (Fixed at “L”).
28
TEST2
I
Test terminal (Fixed at “L”).
29
XRST
I
CD reset input.
30
XRSTO
O
CD reset output. “L” : Reset
31
FOK
I
FOK signal input.
32
LRCK
O
L/R clock signal output.
33
LRCKI
I
L/R clock signal input.
34
PCMD
O
PCM data output.
35
PCMDI
I
PCM data input.
36
BCK
O
Bit clock signal output.
37
BCKI
I
Bit clock signal input.
38
GTOP
–
Not used (Open).
39
XPCK
–
Not used (Open).
40
GFS
–
Not used (Open).
41
RFCK
–
Not used (Open).
42
C2PO
–
Not used (Open).
43
DVSS
–
Digital ground.
44
DVDD
–
Digital power supply (+5V).
45
XROF
–
Not used (Open).
– 11 –
Pin No.
Pin name
I/O
Description
46
MNT3
–
Not used (Open).
47
MNT1
–
Not used (Open).
48
MNT0
–
Not used (Open).
49
C4M
–
Not used (Open).
50
DOUT
–
Not used (Open).
51
EMPHI
–
Not used (Open).
52
WFCK
–
Not used (Open).
53
SCOR
–
Not used (Open).
54
SBSO
–
Not used (Open).
55
EXCK
–
Not used (Open).
56
DTEST
I
Test terminal (Fixed at “L”).
57
CTEST
I
Test terminal (Fixed at “L”).
58
FR
I
≠ key input.
59
PLAY/PAUSE
I
fl key input.
60
FF
I
± key input.
61
STOP
I
p key input.
62
MODE
I
PLAY MODE key input.
63
DISP/ENTER
I
DISPLAY/ENTER key input.
64
AU MUTE
O
Audio mute signal output.
65
BTL MUTE
O
BTL mute signal output.
66
SENCE2
I
CD SENCE input.
67
REC
I
Function REC input.
68
LIMIT SW
I
LIMIT switch input.
69
OPEN/CLOSE
I
CD door open/close switch input.
70
RMC
–
Not used (Fixed at “H”).
71
DVSS
–
Digital ground.
72
DVDD
–
Digital power supply (+5V).
73
SEG 15
–
Not used (Open).
74
SEG 14
–
Not used (Open).
75 – 88
SEG 1 – 13
O
LCD segment output.
89 – 92
COM 0 – 3
O
LCD common output.
93 – 95
VCL 1 – 3
I
LCD drive device voltage input.
96
AVSS1
–
Analog ground.
97
AVDD1
–
Analog power supply (+5V).
98
AOUT1
O
Audio output.
99
AIN1
I
Audio input.
100
LOUT1
O
L-CH audio output.
101
AVSS1
–
Analog ground.
102
XVDD
–
Oscillator power supply (+5V).
103
XTAI
I
Oscillator connect terminal (16.9344MHz).
104
XTAO
O
Oscillator connect terminal (16.9344MHz).
105
XVSS
–
Oscillator ground.
106
AVSS2
–
Analog ground.
107
LOUT2
O
R-CH audio output.
108
AIN2
I
Audio input.
109
AOUT2
O
Audio output.
110
AVDD2
–
Digital power supply (+5V).
111
AVSS2
–
Ground terminal.
112
NC
–
Not used (Open).
– 12 –
CFD-V15/V24
6-2. BLOCK DIAGRAM
r
CIRCUIT BOARDS LOCATION
AC INLET board
REC SW board
POWER board
BATT board
MONO/ST SW board
(AEP, UK, Italian,
East European, Russian model)
VOL SEL board
(E, Saudi Arabia model)
CONTROL board
CD MOTOR board
MAIN board
• Signal path.
F : FM
E : PB
a : REC
J : CD
– 13 –
– 14 –
– 15 –
– 16 –
CFD-V15/V24
6-4. SCHEMATIC DIAGRAM (MAIN SECTION)
r
Refer to page 29 for IC Block Diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• 2 : nonflammable resistor.
¢
•
: internal component.
: e t o N
: e t o N
The components identi- Les composants identifiés
fied by mark ! or dotted par une marque ! sont criline with mark ! are cri- tiques pour la sécurité.
tical for safety.
Ne les remplacer que par
Replace only with part
une piéce portant le
number specified.
numéro spécifié.
• U : B+ Line.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM (RADIO SECTION)
CD STOP (CD SECTION)
PLAY (TAPE SECTION)
(
) : AM (RADIO SECTION)
REC (TAPE SECTION)
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F : FM
E : PB
a : REC
J : CD
• Abbreviation
CND : Canadian
SP :Singapore
EA
: Saudi Arabia
IT
:Italian
EE
: East European
C&SA : Central and South America
CIS : Russian
– 21 –
– 22 –
– 23 –
– 24 –
CFD-V15/V24
6-5. SCHEMATIC DIAGRAM (CD SECTION)
r
r
Refer to page 30 for IC Block Diagrams.
WAVEFORMS
1
PLAY MODE
4
4.8Vp-p
1.2 ± 0.2
Vp-p
140.5 µsec
IC701 #£
(RFO)
IC702 $§
(MNT3)
VOLT/DIV : 200mV AC
TIME/DIV : 0.5µsec
2
VOLT/DIV : 1V AC
TIME/DIV : 50µsec
5
5Vp-p
4.9Vp-p
140.5 µsec
484nsec
IC702 #ª
(XPCK)
IC702 $¶
(MNT1)
VOLT/DIV : 1V AC
TIME/DIV : 0.1µsec
3
VOLT/DIV : 1V AC
TIME/DIV : 50µsec
6
5Vp-p
237nsec
IC702 $¡
(RFCK)
2.5Vp-p
16.9344 MHz
VOLT/DIV : 1V AC
TIME/DIV : 50nsec
IC702 `⁄‚›
(XTAO)
VOLT/DIV : 0.5V AC
TIME/DIV : 20nsec
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
Note:
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés
par une marque ! sont critiques pour la sécurité.
Ne les remplacer que par
une piéce portant le
numéro spécifié.
• U : B+ Line.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD STOP
(
) : REC
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD
• Abbreviation
CND : Canadian
SP :Singapore
EA
: Saudi Arabia
IT
:Italian
EE
: East European
C&SA : Central and South America
CIS : Russian
– 25 –
– 26 –
– 27 –
– 28 –
IC BLOCK DIAGRAMS (MAIN SECTION)
6
7
8
9
10
11
12
13
F+
FIN
(FIN)
VREF
VCC
VCC
(TIN)
TIN
T–
T+
VREF
SP I
26
25
24
23
22
21
20
19
18
17
16
15
VCC
DRIVE
DRIVE
VCC
LIN
MIC
I/EX
L. RAD
REC
L. LO
VCC
R. LO
LINE
R. RAD
TAPE
R. LIN
MIC
IN
22
21
20
19
18
17
16
15
14
13
LEVEL SHIFT
MUTE
DRIVE
DRIVE
DRIVE
2
3
4
5
6
7
8
9
10
11
12
13
14
SL IN
RESET
REGB
REGO
MUTE
GND
(SP IN)
SP IN
SP –
SP +
GND
SPO
RF_I
CP
CB
CC1
CC2
FOK
VEE
FOCUS
PHASE COMPENSATION
NAB
AMP2
26dB
REC
AMP2
DET
FLB
FE_O
L. PO
L. NF
L. RO
L. IN
REF
7
8
9
10
11
– 29 –
CC1
DFCT1
MIRR
8
9
10
11
12
13
TA_O
FGD
7
TA_M
6
12
MIC
NF
6
R. PO
5
R. NF
4
R. RO
3
FSET
TG2
FSET
5
10k
R. IN
2
Charge
up
VEE
TG2
4
1k
GND
1
AGC
AMP
VEE
TGU
3
2.1
REF
– 30 –
23
XRST
22
DATA
21
XLT
20
CLK
19
LOCK
18
VCC
17
ISET
16
SL_O
15
SL_M
14
SL_P
TM5
TM3
SRCH
2
ON
ALC2
C. OUT
TM6
FE_M
1
FDFCT
MIC
AMP1
24
VCC
FS4
MUTE
10k
SENS1
TM7
FS1
FS2
FEI
10k
REC
AMP1
TM4
VCC
FEO
A1
A2
26dB
ISET
VEE
BUF AMP
NAB
AMP1
TG1
TAPE
BUF AMP
ALC1
TG1-2 TM1-7 PS1-4
TRACKING
PHASE COMPENSATION
DFCT
10k
10k
LDON
VCC
FZC COMP.
10k
10k
IFB4
TDFCT 50
VC 51
BUF AMP
B2
24
TM1
–––––
TAPE
ON
ON
MUTE
–––––
TAPE
TAPE
DFCTO IFB1-6 FS1-4
BAL1-4
TOG1-4
FZC 52
10k
VCC
VCC
1
VCC
BUF AMP
B1
TTL
↓
IIL
IIL DATA REGISTER,
INPUT SHIFT REGISTER,
ADDRESS DECODER,
SENS SELECTOR,
OUTPUT DECODER
DFCT
TZC COMP.
LINE
10k
IIL
↓
TTL
MIRR
FOH
FOL
TGH
TGL
BALH
BALL
ATSC
TZC
FZC
TZC 49
SL +
MONITOR
AMP
IFB3
E-F BALANCE
WINDOW COMP.
ATSC
WINDOW
COMP.
SL –
RADIO
RADOI
7dB
MONITOR
AMP
LINE
10k
VCC
FOK
ATSC 48
LEVEL SHIFT
1k
7dB
FO. BIAS
WINDOW
COMP.
TRK. GAIN
WINDOW COMP.
DRIVE
10k
LOGIC
6k
VEE
TEI 47
REG VOLTAGE DOWN,
BIAS VOLTAGE DOWN,
THERMAL SHUT DOWN
MONITOR
SENS2
VEE
LEVEL S VEE
TEO 45
1k
10k
DFCT
DRIVER MUTE
23
10k
VCC
LEVEL SHIFT
LEVEL SHIFT
24
IIL
↓
TTL
VCC
FE AMP
IFB2
IFB1
VEE
VEE 44
26
VEE
TGFL
F–
27
DRIVE
GND
28
DRIVE
AM IF IN
13 14 15
THERMAL
SHUT DOWN
6k
27
E IV AMP
EI 43
IC301 TA2068N
15k
28
VCC
IC BLOCK DIAGRAMS (CD SECTION)
BAND SELECT
11 12
FM IF IN
RIPPLE
FILTER
10
TUND IND
VCC
9
1k
29
VEE
LPF1 46
10k
30
LASER POWER CONTROL
E 42
IC703 BA6898FP
GND
8
31
IFB5
5
F IV AMP
BAND PASS
MUTE
AFC/AGC 2
7
32
APC
F 41
r
AFC/AGC 1
6
33
IFB6
4
BAL1
TUNING
INDICATOR
LCH OUT
RCH OUT
PILOT DET
LPF 1
PILOT DET
LPF 2
ST IND/
VCO CHECK
PLL LPF 1
3
2
VCC
BAL2
BAL3
BAL4
PD 2
AUTOBLEND
5
34
RF
SUMMING
AMP
FE_
BIAS 40
MUTING
4
3
35
PD1 IV
AMP
TOG1
TOG2
TOG3
TOG4
PD 1
AM
IF / DET
DECORD AMP
2
T.S.D
GND
1
1
PD2 IV
AMP
FM IF /
DISCRI
MPX REG.
RIPPLE
FILTER
36
TGFL
FM/AM
FE OUT
AFC
REG
REG
MONO/ST
SELECT
37
CH-2
STANDBY
SWITCH
AM FRONT-END
1/2
COUNTER
1/2
COUNTER
38
VEE
FM FRONT-END
VCO
39
BIAS
CIRCUIT
LPC
FE GND
16
RF_O
FM RF IN
17
LPCL
AM RF IN
18
RF_M
FM RF
19
RFTC
REG OUT
20
LD
FM
DISCRI
MUTE
26 25 24 23 22 21
PDO
VCO
27
CH-2
PD1
MPX REG
28
FM OSC
PLL LPF2
29
AM OSC
GND
30
IC701 CXA1992BR
PD2
IC304 LA4597
IC1 CAX1538S
GND
r
– 31 –
TM2
Ver 1.1 1998.08
SECTION 7
EXPLODED VIEWS
NOTE :
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Color indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ••• (RED)
↑
↑
Parts color Cabinet's color
• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
7-3. REAR CABINET SECTION
7-2. UPPER CABINET SECTION
• The mechanical parts with no reference
number in the exploded views are not
supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
• Abbreviation
CND : Canadian
SP : Singapore
EA
: Saudi Arabia IT
: Italian
EE
: East European CIS : Russian
C&SA : Central & South America
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
104
108
Les composants identifiés par une
marque ! sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
59
60 61
62
69
109
107
107
63
64
F902
58
#1
113
#1
111
T901
#1
106
112
65
57
#6
AEP, UK, IT,
EE, CIS model
#6
EXCEPT
WHITE model #10
WHITE model #12
#6
66
55
#1
9
#8
56
54
67
#1
#1
70
not supplied
#4
#3
77
68
71
72
#6
#1
116
#1
#1
53
8
105
73
LCD800
11
#1
7
6
71
72
WHITE model
SP302
110
115
#2
EXCEPT WHITE model
#6
#11
10
4
#1
F901
7-1. FRONT CABINET SECTION
SP301
ANT1
E, EA model
76
74
8
#1
5
103
S801
51
52
2
75
114
#10 EXCEPT WHITE model
#12 WHITE model
1
8
Ref. No.
12
Ref. No.
Part No.
101
102
Description
Remark
Ref. No.
5
1
1
1
1
1
X-3375-386-1
X-3375-390-1
X-3375-392-1
X-3375-394-1
X-3375-395-1
CABINET (FRONT) SUB ASSY (SP)
CABINET (FRONT) SUB ASSY (EA)
CABINET (FRONT) SUB ASSY (EE)
CABINET (FRONT) SUB ASSY (C&SA)
CABINET (FRONT) SUB ASSY (IT)
1
1
1
1
1
X-3375-396-1 CABINET (FRONT) SUB ASSY (E)
X-3375-397-1 CABINET (FRONT) SUB ASSY (DARK GRAY)
(US)
X-3375-400-1 CABINET (FRONT) SUB ASSY (AEP,UK,CIS)
X-3375-903-1 CABINET (FRONT) SUB ASSY (WHITE) (US)
X-4949-821-1 CABINET (FRONT) SUB ASSY (CND)
2
2
2
4
3-018-837-01
3-018-837-11
3-018-837-21
3-018-839-01
KNOB (VOL) (DARK GRAY) (EXCEPT SP,EA)
KNOB (VOL) (SP,EA)
KNOB (VOL) (WHITE) (US)
POINTER
Ref. No.
Part No.
Description
3-018-840-11
3-018-840-21
3-018-842-01
1-668-281-11
4-951-620-01
KNOB (TU) (SP,EA)
KNOB (TU) (WHITE) (US)
CHASSIS (TU)
CONTROL BOARD
SCREW (2.6X8), +BVTP
9
10
11
* 12
LCD800
3-703-397-01
3-018-845-01
3-018-838-01
3-022-854-01
1-801-913-11
STOPPER, WIRING
HOLDER (LCD)
BUTTON (MEGA BASS)
CHASSIS (DUCT)
DISPLAY PANEL, LIQUID CRYSTAL
– 32 –
Description
51
52
53
53
54
3-009-208-01
3-922-112-11
3-009-186-42
3-009-186-61
3-009-209-01
55
56
57
57
58
Remark
Ref. No.
Part No.
Description
Remark
SPRING, CASSETTE UP
DAMPER
CABINET (UPPER)
CABINET (UPPER) (WHITE) (US)
SPRING, CD UP
63
64
64
* 65
66
3-009-200-41
3-009-195-31
3-009-195-41
3-009-206-01
3-009-214-01
BUTTON (STOP) (WHITE) (US)
BUTTON (PAUSE)
BUTTON (PAUSE) (WHITE) (US)
SHAFT (MD)
SPRING, REC
3-019-395-01
1-452-899-11
3-009-187-42
3-009-187-61
X-3375-399-1
PLATE, CHUCKING
MAGNET
LID, CD
LID, CD (WHITE) (US)
HOLDER SUB ASSY, CASSETTE
67
* 68
* 68
69
69
4-951-620-01
1-668-287-11
1-668-287-21
3-009-201-31
3-009-201-41
SCREW (2.6X8), +BVTP
REC SW BOARD (US,CND, C&SA)
REC SW BOARD (EXCEPT US,CND, C&SA)
HANDLE
HANDLE (WHITE) (US)
58
59
59
60
60
X-3375-904-1
3-009-196-31
3-009-196-41
3-009-199-31
3-009-199-41
HOLDER SUB ASSY, CASSETTE (WHITE) (US)
BUTTON (REC)
BUTTON (REC) (WHITE) (US)
BUTTON (PLAY)
BUTTON (PLAY) (WHITE) (US)
70
71
72
73
74
3-923-736-01
3-910-095-11
3-910-095-01
1-777-955-11
1-639-678-12
COVER, CD
RUBBER, VIBRATION PROOF (RED)
RUBBER, VIBRATION PROOF (GREEN)
WIRE (FLAT TYPE) (16 CORE)
CD MOTOR BOARD
61
61
62
62
63
3-009-198-31
3-009-198-41
3-009-197-31
3-009-197-41
3-009-200-31
BUTTON (REW)
BUTTON (REW) (WHITE) (US)
BUTTON (FF)
BUTTON (FF) (WHITE) (US)
BUTTON (STOP)
75
76
* 77
S801
3-015-646-01
3-923-151-01
1-668-288-21
1-692-960-11
CUSHION (CD)
CUSHION, RUBBER
MONO/ST SW BOARD (AEP,EE,IT,CIS,UK)
SWITCH, PUSH (1 KEY) (DOOR OPEN/CLOSE)
3-018-840-01 KNOB (TU) (DARK GRAY) (EXCEPT SP,EA)
5
5
* 6
* 7
8
SP301
SP302
Remark
Part No.
1-505-889-11 SPEAKER (10cm) (L-CH)
1-505-889-11 SPEAKER (10cm) (R-CH)
– 33 –
Part No.
Description
Remark
*
*
*
*
*
101
102
102
102
102
3-009-215-01
A-3321-040-A
A-3321-152-A
A-3321-156-A
A-3321-157-A
TERMINAL (ANALOG), ANTENNA
MAIN BOARD, COMPLETE (US)
MAIN BOARD, COMPLETE (EA)
MAIN BOARD, COMPLETE (IT)
MAIN BOARD, COMPLETE (CND)
*
*
*
*
102
102
102
102
A-3321-159-A
A-3321-160-A
A-3321-172-A
A-3321-303-A
MAIN BOARD, COMPLETE (E)
MAIN BOARD, COMPLETE (AEP,CIS,UK)
MAIN BOARD, COMPLETE (EE)
MAIN BOARD, COMPLETE (C&SA)
* 102
103
103
103
* 104
A-3321-304-A
3-009-194-31
3-009-194-41
3-009-194-51
1-668-282-11
MAIN BOARD, COMPLETE (SP)
KNOB (FUN) (DARK GRAY)(EXCEPT SP,EA)
KNOB (FUN) (SP,EA)
KNOB (FUN) (WHITE) (US)
VOL SEL BOARD (E,EA)
105
106
106
106
106
3-009-192-01
X-3375-384-1
X-3375-387-1
X-3375-391-1
X-3375-393-1
GEAR, TUNING CAPACITOR
CABINET (REAR) (CND,C&SA)
CABINET (REAR) (SP)
CABINET (REAR) (EA,E)
CABINET (REAR) (EE)
106
106
106
107
* 108
X-3375-398-1
X-3375-902-1
X-3375-401-1
1-533-233-31
1-668-284-11
CABINET (REAR) (DARK GRAY) (US)
CABINET (REAR) (WHITE) (US)
CABINET (REAR) (AEP,IT,UK,CIS)
HOLDER, FUSE
POWER BOARD (US,CND, C&SA)
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
* 108
* 109
* 109
* 109
110
1-668-284-21 POWER BOARD (EXCEPT US,CND, C&SA)
1-668-285-11 AC INLET BOARD (US,CND, C&SA)
1-668-285-21 AC INLET BOARD (EXCEPT US,CND,
C&SA,E,EA)
1-668-833-11 AC INLET BOARD (E,EA)
3-009-210-01 SPRING, BATTERY TERMINAL COIL
111
* 112
* 112
113
113
* 114
3-009-211-01
1-668-286-11
1-668-286-21
3-009-202-31
3-009-202-41
3-023-888-01
115
116
ANT1
! F901
! F902
3-989-888-03
3-703-397-01
1-501-883-11
1-532-467-31
1-532-464-31
! F902
! T901
! T901
! T901
! T901
– 34 –
Description
Les composants identifiés par une
marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Remark
SPRING, BATTERY TERMINAL COIL
BATT BOARD(US,CND, C&SA)
BATT BOARD(EXCEPT US,CND, C&SA)
LID, BATTERY CASE(DARK GRAY)
LID, BATTERY CASE (WHITE) (US)
PLATE (CD), SHIELD
CUSHION (AIR)
STOPPER, WIRING
ANTENNA, TELESCOPIC
FUSE, TIME LAG (T0.315AL/250V) (E,EA)
FUSE, TIME LAG (T2.5AL/250V) (EXCEPT
US,CND,C&SA)
1-533-618-11 FUSE, GLASS CYLINDERICAL (3.15A/250V)
(US,CND,C&SA)
1-431-231-11 TRANSFORMER, POWER
(AEP,EE,IT,CIS,UK,SP,AR)
1-431-230-11 TRANSFORMER, POWER (US)
1-431-230-21 TRANSFORMER, POWER (CND,C&SA)
1-431-233-11 TRANSFORMER, POWER (E,EA)
7-4. MECHANISM DECK SECTION (1)
(MF-V10-117)
HRP301
159
170
HE301
158
160
161
162
169
168
163
157
155
156
167
164
165
154
153
166
151
152
Ref. No.
Part No.
Description
151
152
153
154
155
3-933-010-01
3-933-025-01
3-933-026-01
3-933-024-01
3-933-019-01
SPRING (S/P), TORSION
SPRING (P), TORSION
LEVER (P)
ROLLER, PINCH
SPRING (F/R), TORSION
156
157
158
159
* 160
3-933-028-01
3-933-016-01
3-008-590-01
3-008-592-13
3-008-588-01
SPRING (FWD), TORSION
GEAR (S REEL)
SLIDER (REC)
BASE (H), HEAD
SLIDER (REW)
* 161
3-008-589-01 SLIDER (FF)
Remark
Ref. No.
Part No.
Description
* 162
* 163
164
* 165
3-008-587-01
3-008-591-01
3-933-004-01
3-933-021-01
SLIDER (STOP)
SLIDER (PAUSE)
CLAW, REEL
SLIDER (FRP)
* 166
167
168
169
* 170
3-933-006-01
3-934-833-01
3-934-834-01
3-933-007-01
3-012-114-01
SLIDER (EJECT)
SPRING (FRP)
SPRING (BT)
PLATE, LOCK
LEVER (FR)
Remark
HE301 1-543-876-11 HEAD (ERASE)
HRP301 1-500-364-11 HEAD,MAGNETIC(RECORD/PLAYBACK)
– 35 –
7-5. MECHANISM DECK SECTION (2)
(MF-V10-117)
207
206
219
209
208
205
204
210
216
203
211
S601
218
212
M601
213
217
214
202
Ref. No.
Part No.
#7
201
Description
201
202
203
204
205
3-933-029-01
3-933-182-01
3-932-995-01
X-3371-667-1
3-932-997-01
LEVER, ERASING PREVENTION
SPRING, CASSETTE
GEAR (MID)
CLUTCH ASSY
GEAR (CAM)
* 206
207
208
209
210
3-932-999-01
3-932-998-01
3-009-648-01
3-936-438-01
X-3373-572-1
SLIDER (SW)
SPRING (GROUND), TORSION
LEVER (S.OFF)
LEVER (K)
REEL ASSY (N), T
Remark
Ref. No.
215
220
Part No.
Description
211
212
213
214
215
3-933-020-01
X-3372-924-1
3-932-993-01
3-343-358-01
3-933-005-01
BELT
FLYWHEEL ASSY
CHASSIS, OUTSERT
RING, RETAINING
SPRING (CAM), COMPRESSION
216
217
218
219
220
3-939-383-02
3-937-760-01
3-934-336-01
3-009-650-02
3-016-349-01
SPRING, COMPRESSION
SPRING (GROUND), COMPRESSION
BEARING
SPRING (K), COMPRESSION
WASHER
M601
S601
A-3304-619-A MOTOR ASSY
1-762-679-11 SWITCH, LEAF (MD POWER)
– 36 –
Remark
7-6. OPTICAL PICK-UP SECTION
(KSM-213CDM)
253
254
not supplied
252
#5
255
M702
M701
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Ref. No.
251
252
Part No.
Description
2-626-908-01 SHAFT, SLED
2-627-003-02 GEAR (B) (RP)
Remark
Les composants identifiés par une
marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ref. No.
Part No.
253
! 254
255
2-626-907-01 GEAR (A) (S)
8-848-483-05 OPTICAL PICK-UP KSS-213C
X-2626-202-1 CHASSIS ASSY (MB) (RP), MOTOR
(INCLUDING M702) (SPINDLE)
X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)
M701
– 37 –
Description
251
Remark
AC INLET
BATT
CONTROL
CD MOTOR
MAIN
NOTE :
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable
• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
SECTION 8
ELECTRICAL PARTS LIST
• SEMICONDUCTORS
In each case, u : µ , for example :
uA.... : µ A.... , uPA.... : µ PA....
uPB.... : µ PB.... , uPC.... : µ PC....
uPD.... : µ PD....
• CAPACITORS
uF : µ F
• COILS
uH : µ H
• Abbreviation
CND : Canadian
SP : Singapore
EA
: Saudi Arabia IT
: Italian
EE
: East European CIS : Russian
C&SA : Central & South America
KR
: Korean
Ref. No.
Part No.
Description
Remark
*
*
*
1-668-285-11 AC INLET BOARD (US,CND,C&SA)
1-668-285-21 AC INLET BOARD (EXCEPT US,CND,C&SA)
1-668-833-11 AC INLET BOARD (E,EA)
**************
Ref. No.
Part No.
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ! sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference number, please include the board.
Description
Remark
< LIQUID CRYSTAL DISPLAY >
LCD800 1-801-913-11 DISPLAY PANEL, LIQUID CRYSTAL
< SWITCH >
1-533-233-31 HOLDER, FUSE (E,EA)
S355
S801
S802
S803
S804
< CONNECTOR >
* CNP905 1-564-752-11 PIN, CONNECTOR (WITH LOCK) 3P (E,EA)
1-762-950-11
1-762-798-11
1-762-798-11
1-762-798-11
1-762-798-11
SWITCH, PUSH (1 KEY) (MEGA BASS)
SWITCH, KEYBOARD (≠)
SWITCH, KEYBOARD (±)
SWITCH, KEYBOARD (PLAY MODE)
SWITCH, KEYBOARD (DISPLAY/ENTER)
< FUSE >
! F901
S805
1-762-798-11 SWITCH, KEYBOARD (fl)
S806
1-762-798-11 SWITCH, KEYBOARD (p)
************************************************************
1-532-467-31 FUSE, TIME LAG (T0.315AL/250V) (E,EA)
< JACK >
! J901
! J901
! J901
1-526-818-11 INLET, AC (⁄ AC IN) (C&SA)
1-526-838-11 INLET, AC 2P (⁄ AC IN) (EXCEPT
US,CND,C&SA)
1-540-009-11 INLET, AC (⁄ AC IN) (US,CND)
< CABLE, HOLDER >
* KH901 1-573-287-11 HOLDER, CABLE 2P
* KH902 1-573-287-11 HOLDER, CABLE 2P
* KH903 1-573-287-11 HOLDER, CABLE 2P
************************************************************
*
*
1-668-286-11 BATT BOARD (US,CND,C&SA)
1-668-286-21 BATT BOARD (EXCEPT US,CND,C&SA)
***********
*
*
*
*
*
A-3321-040-A
A-3321-152-A
A-3321-156-A
A-3321-157-A
A-3321-159-A
MAIN BOARD, COMPLETE (US)
MAIN BOARD, COMPLETE (EA)
MAIN BOARD, COMPLETE (IT)
MAIN BOARD, COMPLETE (CND)
MAIN BOARD, COMPLETE (E)
*
*
*
*
A-3321-160-A
A-3321-172-A
A-3321-303-A
A-3321-304-A
MAIN BOARD, COMPLETE (AEP,CIS,UK)
MAIN BOARD, COMPLETE (EE)
MAIN BOARD, COMPLETE (C&SA)
MAIN BOARD, COMPLETE (SP)
********************
*
3-009-192-01
3-009-194-31
3-009-194-41
3-023-888-01
GEAR, TUNING CAPACITOR
KNOB (FUN) (EXCEPT KR,EA)
KNOB (FUN) (KR,EA)
PLATE (CD), SHIELD
< CAPACITOR >
************************************************************
1-639-678-12 CD MOTOR BOARD
**************
< CONNECTOR >
C1
1-162-215-31 CERAMIC
47PF
C2
C3
C5
1-162-306-11 CERAMIC
1-104-664-11 ELECT
1-162-205-31 CERAMIC
0.01uF
47uF
18PF
C5
1-162-195-31 CERAMIC
4.7PF
C6
1-102-961-00 CERAMIC
C6
1-102-962-00 CERAMIC
C6
C7
1-102-947-00 CERAMIC
1-162-196-31 CERAMIC
27PF
5%
50V
(CFD-V15/CFD-V24:IT,KR,EA)
30PF
5%
50V
(AEP,CIS,UK,SP)
10PF
5%
50V (EE)
5.6PF
10%
50V
(EXCEPT IT,EA)
CNP707 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P
5%
50V
(US,CND,C&SA)
20%
16V
20%
10V
5%
50V
(EXCEPT EE)
10%
50V (EE)
< SWITCH >
S701
1-572-085-11 SWITCH, LEAF (LIMIT)
************************************************************
*
1-668-281-11 CONTROL BOARD
**************
3-018-845-01 HOLDER (LCD)
– 38 –
MAIN
Ref. No.
Part No.
Description
Remark
C7
1-162-197-31 CERAMIC
6.8PF
C8
1-162-189-31 CERAMIC
1.5PF
C8
1-162-193-31 CERAMIC
3.3PF
C8
1-162-191-31 CERAMIC
2.2PF
C9
C10
1-162-306-11 CERAMIC
1-162-306-11 CERAMIC
0.01uF
0.01uF
C11
C12
C13
C14
C15
1-126-963-11
1-124-903-11
1-104-664-11
1-104-664-11
1-162-306-11
4.7uF
1uF
47uF
47uF
0.01uF
C16
C17
C18
1-126-961-11 ELECT
1-124-443-00 ELECT
1-161-053-00 CERAMIC
C18
1-162-839-11 CERAMIC
C19
1-161-053-00 CERAMIC
ELECT
ELECT
ELECT
ELECT
CERAMIC
10%
50V
(IT,EA)
20%
50V
(US,CND,C&SA)
10%
50V
(E,EE,KR,EA)
10%
50V
(AEP,IT,CIS,UK,SP)
20%
16V
20%
16V
20%
20%
20%
20%
20%
50V
50V
10V
10V
16V
2.2uF
100uF
0.015uF
20%
50V
20%
10V
10%
50V
(US,CND,C&SA)
0.01uF
10%
16V
(EXCEPT US,CND,C&SA)
0.015uF 10%
50V
(US,CND,C&SA)
C19
1-162-839-11 CERAMIC
C20
C21
C22
C23
1-162-306-11
1-162-205-31
1-124-903-11
1-124-902-00
C24
C25
1-126-963-11 ELECT
1-162-294-31 CERAMIC
4.7uF
0.001uF
C26
C28
C29
1-162-294-31 CERAMIC
1-162-306-11 CERAMIC
1-162-294-31 CERAMIC
0.001uF
0.01uF
0.001uF
20%
50V
10%
50V
(US,CND,C&SA)
10%
50V
20%
16V
10%
50V(EE)
C101
C102
C103
C104
C105
1-162-301-11
1-104-664-11
1-161-020-11
1-162-302-11
1-162-215-31
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
0.0015uF
47uF
0.039uF
0.0022uF
47PF
20%
20%
10%
20%
5%
C108
C109
C121
C122
1-124-902-00
1-124-903-11
1-124-903-11
1-161-057-00
ELECT
ELECT
ELECT
CERAMIC
0.47uF
1uF
1uF
0.033uF
20%
20%
20%
10%
C122
1-162-843-11 CERAMIC
0.022uF
CERAMIC
CERAMIC
ELECT
ELECT
0.01uF
10%
16V
(EXCEPT US,CND,C&SA)
0.01uF
20%
16V
18PF
5%
50V
1uF
20%
50V
0.47uF
20%
50V
16V
10V
16V
16V
50V
50V
50V
50V
50V
(EA,SP)
10%
16V
(EXCEPT EA,SP)
C140
C151
C152
C153
C154
C155
1-124-902-00
1-104-664-11
1-162-294-31
1-124-443-00
1-124-473-11
1-136-165-00
ELECT
ELECT
CERAMIC
ELECT
ELECT
FILM
0.47uF
47uF
0.001uF
100uF
1000uF
0.1uF
20%
20%
10%
20%
20%
5%
50V
10V
50V
10V
10V
50V
C156
C157
C158
C201
C202
1-162-282-31
1-161-020-11
1-162-302-11
1-162-301-11
1-104-664-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
100PF
0.039uF
0.0022uF
0.0015uF
47uF
10%
10%
20%
20%
20%
50V
16V
16V
16V
10V
C203
1-161-020-11 CERAMIC
0.039uF
10%
16V
Ref. No.
Part No.
Description
C204
C205
C208
C209
1-162-302-11
1-162-215-31
1-124-902-00
1-124-903-11
CERAMIC
CERAMIC
ELECT
ELECT
C221
C222
Remark
0.0022uF
47PF
0.47uF
1uF
20%
5%
20%
20%
1-124-903-11 ELECT
1-161-057-00 CERAMIC
1uF
0.033uF
20%
10%
C222
1-162-843-11 CERAMIC
0.022uF
C240
C251
1-124-902-00 ELECT
1-104-664-11 ELECT
0.47uF
47uF
50V
50V
(EA,SP)
10%
16V
(EXCEPT EA,SP)
20%
50V
20%
10V
C252
C253
C254
C255
C256
1-162-294-31
1-124-443-00
1-124-473-11
1-136-165-00
1-162-282-31
CERAMIC
ELECT
ELECT
FILM
CERAMIC
0.001uF
100uF
1000uF
0.1uF
100PF
10%
20%
20%
5%
10%
50V
10V
10V
50V
50V
C257
C258
C301
C302
C303
1-161-020-11
1-162-302-11
1-124-443-00
1-124-443-00
1-124-907-11
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
0.039uF
0.0022uF
100uF
100uF
10uF
10%
20%
20%
20%
20%
16V
16V
10V
10V
50V
C304
C311
C312
C313
C314
1-124-443-00
1-162-301-11
1-104-664-11
1-130-468-00
1-104-663-11
ELECT
CERAMIC
ELECT
MYLAR
ELECT
100uF
0.0015uF
47uF
560PF
33uF
20%
20%
20%
5%
20%
10V
16V
10V
50V
16V
C315
C316
C317
C320
C341
1-162-306-11
1-124-907-11
1-126-233-11
1-162-306-11
1-126-937-11
CERAMIC
ELECT
ELECT
CERAMIC
ELECT
0.01uF
10uF
22uF
0.01uF
4700uF
20%
20%
20%
20%
20%
16V
50V
50V
16V
16V
C343
C345
C346
C347
C348
1-162-306-11
1-162-306-11
1-162-306-11
1-104-666-11
1-124-472-11
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
0.01uF
0.01uF
0.01uF
220uF
470
20%
20%
20%
20%
20%
16V
16V
16V
25V
10V
C351
C359
C701
C702
C703
1-126-941-11
1-162-306-11
1-162-600-11
1-162-306-11
1-162-305-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
470
0.01uF
0.0047uF
0.01uF
0.0068uF
20%
20%
20%
20%
20%
25V
16V
16V
16V
16V
C704
C705
C706
C707
C708
1-130-491-00
1-162-306-11
1-104-664-11
1-161-494-00
1-136-165-00
MYLAR
CERAMIC
ELECT
CERAMIC
FILM
0.047uF
0.01uF
47uF
0.022uF
0.1uF
5%
20%
20%
5%
50V
16V
10V
25V
50V
C709
C710
C711
C712
C713
1-136-165-00
1-162-302-11
1-162-203-31
1-162-294-31
1-136-165-00
CERAMIC
CERAMIC
CERAMIC
CERAMIC
FILM
0.1uF
0.0022uF
15PF
0.001uF
0.1uF
20%
5%
10%
5%
50V
16V
50V
50V
50V
C714
C715
C716
C717
C718
1-136-165-00
1-124-903-11
1-136-165-00
1-136-165-00
1-131-377-00
FILM
ELECT
FILM
MYLAR
TANTALUM
0.1uF
1uF
0.1uF
0.1uF
10uF
5%
20%
5%
5%
10%
50V
50V
50V
50V
10V
C719
C720
1-104-664-11 ELECT
1-162-306-11 CERAMIC
47uF
0.01uF
20%
20%
10V
16V
– 39 –
16V
50V
50V
50V
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
C721
C722
C723
1-130-489-00 MYLAR
1-130-489-00 MYLAR
1-162-306-11 CERAMIC
0.033uF
0.033uF
0.01uF
5%
5%
20%
50V
50V
16V
C829
C724
C725
C726
C727
C728
1-130-489-00
1-137-440-11
1-162-306-11
1-162-199-31
1-104-664-11
MYLAR
FILM
CERAMIC
CERAMIC
ELECT
0.033uF
0.018uF
0.01uF
10PF
47uF
5%
5%
20%
5%
20%
50V
50V
16V
50V
10V
CF1
CF2
C729
C730
C731
C732
C733
1-126-962-11
1-130-493-00
1-162-215-31
1-162-306-11
1-162-282-31
ELECT
MYLAR
CERAMIC
CERAMIC
CERAMIC
3.3uF
0.068uF
47PF
0.01uF
100PF
20%
5%
5%
20%
10%
50V
50V
50V
16V
50V
C734
C735
C736
C737
C739
1-162-282-31
1-162-282-31
1-162-294-31
1-161-494-00
1-162-282-31
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
100PF
100PF
0.001uF
0.022uF
100PF
10%
10%
10%
10%
50V
50V
50V
25V
50V
C740
C741
C742
C743
C744
1-162-282-31
1-162-305-11
1-162-306-11
1-104-664-11
1-124-472-11
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
100PF
0.0068uF
0.01uF
47uF
470uF
10%
20%
20%
20%
20%
50V
16V
16V
10V
10V
C760
C761
C762
1-162-306-11 CERAMIC
1-162-294-31 CERAMIC
1-162-282-31 CERAMIC
C799
C801
1-130-491-00 MYLAR
1-104-664-11 ELECT
C802
C804
C805
C806
C807
1-126-233-11
1-104-666-11
1-126-963-11
1-126-963-11
1-162-292-31
ELECT
ELECT
ELECT
ELECT
CERAMIC
22uF
220uF
4.7uF
4.7uF
680PF
20%
20%
20%
20%
10%
50V
6.3V
50V
50V
50V
C808
C809
C810
C811
C812
1-162-292-31
1-162-284-31
1-162-284-31
1-124-907-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
680PF
150PF
150PF
10uF
0.01uF
10%
10%
10%
20%
20%
50V
50V
50V
50V
16V
C813
C814
C815
C816
C817
1-104-664-11
1-162-306-11
1-162-203-31
1-162-203-31
1-162-306-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
47uF
0.01uF
15PF
15PF
0.01uF
20%
20%
5%
5%
20%
10V
16V
50V
50V
16V
C818
C819
C820
C821
C822
1-162-306-11
1-162-306-11
1-136-173-00
1-162-306-11
1-162-290-31
CERAMIC
CERAMIC
FILM
CERAMIC
CERAMIC
0.01uF
0.01uF
0.47uF
0.01uF
470PF
20%
20%
5%
20%
10%
16V
16V
50V
16V
50V
C823
C824
C825
C826
C827
1-162-286-21
1-136-169-00
1-162-306-11
1-162-306-11
1-162-282-31
CERAMIC
FILM
CERAMIC
CERAMIC
CERAMIC
220PF
0.22uF
0.01uF
0.01uF
100PF
10%
5%
20%
20%
10%
50V
50V
16V
16V
50V
C827
1-162-286-21 CERAMIC
220PF
10%
C828
1-162-306-11 CERAMIC
0.01uF
Part No.
Description
1-162-306-11 CERAMIC
Remark
0.01uF
20%
16V
< FILTER >
1-760-738-61 FILTER, CERAMIC
1-577-072-11 FILTER, CERAMIC
< CONNECTOR >
*
*
*
*
CNP301
CNP302
CNP303
CNP304
CNP702
1-506-986-11
1-506-986-11
1-506-986-11
1-506-987-11
1-770-674-11
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 5P
CONNECTOR, FFC/FPC 16P
CNP801
CNP802
CNP803
CNP901
1-691-584-11
1-691-583-21
1-691-573-11
1-691-573-11
PIN, CONNECTOR (PC BOARD) 13P
PIN, CONNECTOR (PC BOARD) 12P
PIN, CONNECTOR (PC BOARD) 2P
PIN, CONNECTOR (PC BOARD) 2P
< TRIMMER >
CT1
CT1
CT1
CT2
CT2
0.01uF
20%
16V
0.001uF 10%
50V
100PF
10%
50V
(EXCEPT CFD-V15/CFD-V24 : EA)
0.047uF 5%
50V
47uF
20%
10V
CT2
CT3
CT3
CT3
CT4
CT4
CT4
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
< VARIABLE CAPACITOR >
CV1
CV1
CV1
CV2
CV2
CV2
CV3
CV3
CV3
CV4
CV4
CV4
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING) (EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
1-141-559-11 CAP, VAR (TUNING) (US,CND,C&SA)
1-141-561-11 CAP, VAR (TUNING)(EXCEPT US,CND,
C&SA,EE)
1-141-560-11 CAP, VAR (TUNING) (EE)
< DIODE >
50V
(C&SA,SP)
20%
16V
D1
D2
D301
D303
D304
– 40 –
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
MAIN
Ref. No.
Part No.
Description
D305
D306
D307
D308
D309
8-719-991-33
8-719-991-33
8-719-991-33
8-719-109-90
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
Remark
D310
D311
D312
D314
D317
8-719-059-97
8-719-109-98
8-719-991-33
8-719-991-33
8-719-991-33
LED L-34HD (OPR/BATT)
DIODE RD6.8ES-B3
DIODE 1SS133T-77 (EXCEPT US)
DIODE 1SS133T-77
DIODE 1SS133T-77
D318
8-719-991-33 DIODE 1SS133T-77
1SS133T-77
1SS133T-77 (EXCEPT US)
1SS133T-77 (EXCEPT US)
RD5.6ESB3
1SS133T-77
Ref. No.
Part No.
Q202
Q203
Q301
Q306
Q307
8-729-194-57
8-729-194-57
8-729-281-53
8-729-036-67
8-729-119-76
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC945-P
2SC945-P
2SC1815-GR
KRC111M-AT
2SA1175-HFE
Q308
Q309
Q310
Q701
8-729-036-57
8-729-021-82
8-729-036-86
8-729-037-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KRC101M-AT
2SD2396K
KTC3203Y-AT
KTA1271-Y-AT
< RESISTOR >
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
R1
1-247-815-91 CARBON
220
R2
R3
R4
1-249-421-11 CARBON
1-249-441-11 CARBON
1-247-843-11 CARBON
2.2K
100K
3.3K
< FILTER >
R4
1-162-191-31 CERAMIC
2.2PF
R4
1-162-195-31 CERAMIC
4.7PF
< IC >
R5
1-249-411-11 CARBON
IC
IC
IC
IC
IC
R5
1-249-413-11 CARBON
R5
1-249-414-11 CARBON
R6
1-249-403-11 CARBON
50V
(EA)
330
5%
1/4W
(EXCEPT US,CND,C&SA,EE)
470
5%
1/4W
(US,CND,C&SA)
560
5%
1/4W
(EE)
68
5%
1/4W
R7
R8
R13
R14
R15
1-249-427-11
1-249-427-11
1-249-421-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
6.8K
2.2K
10K
10K
R101
R102
R103
R104
R105
1-249-431-11
1-249-404-00
1-249-441-11
1-247-843-11
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
15K
82
100K
3.3K
33K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R106
R109
R110
R121
R122
1-249-421-11
1-249-426-11
1-247-807-31
1-249-417-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
5.6K
100
1K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R123
R124
1-247-895-91 CARBON
1-249-413-11 CARBON
470K
470
5%
5%
R124
1-249-417-11 CARBON
L4
COIL, AIR-CORE (US,CND,C&SA)
COIL, AIR-CORE (AEP,IT,CIS,UK,SP,EA,E)
COIL, AIR-CORE (EE)
COIL, AIR-CORE (CFD-V15)
COIL, AIR-CORE (AEP,CIS,UK,SP)
COIL (WITH CORE) (EE)
COIL (WITH CORE) (IT,EA)
ANTENNA, FERRITE-ROD (MW)
(US,CND,C&SA)
1-501-841-21 ANTENNA, FERRITE-ROD (MW)
(EXCEPT US,CND,C&SA)
1-406-040-00 COIL (OSC)
R124
1-249-421-11 CARBON
L701
L702
1-412-488-11 INDUCTOR
1-410-509-11 INDUCTOR
R140
1-249-441-11 CARBON
1/4W
1/4W
(EA,SP)
1K
5%
1/4W
(C&SA,E)
2.2K
5%
1/4W
(EXCEPT C&SA,E,EA,SP)
100K
5%
1/4W
R141
R143
R151
R153
R154
1-249-419-11
1-249-429-11
1-249-417-11
1-247-807-31
1-247-807-31
1.5K
10K
1K
100
100
5%
5%
5%
5%
5%
FL1
FL1
1-410-397-21
1-410-397-21
1-410-397-21
1-410-397-21
1-410-397-21
Remark
8-729-194-57 TRANSISTOR 2SC945-P
8-729-036-80 TRANSISTOR KRC110M
< FERRITE BEAD >
FB151
FB251
FB351
FB807
FB808
Description
Q103
Q201
1-236-711-31 FILTER, BAND PASS (E,AEP,IT,CIS,UK,EA,SP)
1-233-452-11 FILTER, BAND PASS (EE)
IC1
IC301
IC304
IC701
IC702
8-752-056-23
8-759-264-71
8-759-820-22
8-752-082-14
8-752-893-95
CXA1538S
TA2068N
LA4597
CXA1992BR
CXP401-601R
IC703
8-759-473-42 IC BA6898FP
< JACK >
J301
1-566-891-11 JACK (2)
5%
1/4W
(US,CND,C&SA,EE)
5%
1/4W
5%
1/4W
5%
1/4W
(US,CND,C&SA)
10%
50V
(IT)
10%
5%
1/4W
5%
1/4W
5%
1/4W
5%
1/4W
5%
1/4W
(AEP,EE,IT,CIS,UK,SP)
< CABLE, HOLDER >
* KH1
* KH804
1-573-287-11 HOLDER, CABLE 2P (AEP,IT,CIS,UK,EE)
1-573-287-11 HOLDER, CABLE 2P
< COIL >
L1
L1
L1
L2
L2
L2
L2
L3
L3
1-406-998-11
1-406-999-11
1-411-266-11
1-411-387-11
1-416-570-11
1-406-958-11
1-406-957-21
1-501-841-11
1uH
10uH (US,CND,C&SA,E,EA)
< TRANSISTOR >
Q1
Q101
Q102
8-729-036-57 TRANSISTOR KRC101M-AT
8-729-036-80 TRANSISTOR KRC110M
8-729-194-57 TRANSISTOR 2SC945-P
– 41 –
CARBON
CARBON
CARBON
CARBON
CARBON
1/4W
1/4W
1/4W
1/4W
1/4W
MAIN
Ref. No.
Part No.
Description
R155
R156
R201
R202
R203
R204
R205
1-249-431-11
1-249-437-11
1-249-431-11
1-249-404-00
1-249-441-11
1-247-843-11
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
15K
47K
15K
82
100K
3.3K
33K
5%
5%
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
R206
R209
R210
R221
R222
1-249-421-11
1-249-426-11
1-247-807-31
1-249-417-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
5.6K
100
1K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R223
R224
1-247-895-91 CARBON
1-249-413-11 CARBON
470K
470
5%
5%
R224
1-249-417-11 CARBON
R224
1-249-421-11 CARBON
R240
1-249-441-11 CARBON
1/4W
1/4W
(EA,SP)
1K
5%
1/4W
(C&SA,E)
2.2K
5%
1/4W
(EXCEPT C&SA,E,EA,SP)
100K
5%
1/4W
R241
R243
R251
R253
R254
R255
1-249-419-11
1-249-429-11
1-249-417-11
1-247-807-31
1-247-807-31
1-249-431-11
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
10K
1K
100
100
15K
5%
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
R256
R301
R302
R303
R305
1-249-437-11
1-247-903-00
1-249-441-11
1-249-417-11
1-247-903-00
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1M
100K
1K
1M
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R306
R307
R308
R309
R311
1-249-429-11
1-249-429-11
1-249-417-11
1-249-429-11
1-247-810-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
1K
10K
130
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R312
R313
R314
R315
R319
1-249-427-11
1-249-393-11
1-249-425-11
1-247-863-91
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
10
4.7K
22K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1-249-381-11 CARBON
1
5%
R341
R342
R343
R344
1-249-437-11
1-249-419-11
1-249-415-11
1-247-815-91
CARBON
CARBON
CARBON
CARBON
47K
1.5K
680
220
5%
5%
5%
5%
1/4W F
(US)
1/4W
1/4W
1/4W
1/4W
R345
R346
R347
R348
R349
1-247-815-91
1-249-421-11
1-247-807-31
1-249-421-11
1-249-414-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
2.2K
100
2.2K
560
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R350
R701
R702
R703
R704
1-249-393-11
1-249-440-11
1-249-439-11
1-249-439-11
1-249-439-11
CARBON
CARBON
CARBON
CARBON
CARBON
10
82K
68K
68K
68K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
RV1
RV351
RV352
R705
R706
1-249-439-11 CARBON
1-249-440-11 CARBON
68K
82K
5%
5%
1/4W
1/4W
S351
! R340
Remark
Ref. No.
Part No.
Description
Remark
R707
R709
R710
1-247-887-00 CARBON
1-247-883-00 CARBON
1-247-885-00 CARBON
220K
150K
180K
5%
5%
5%
1/4W
1/4W
1/4W
R711
R712
R714
R715
R716
1-247-883-00
1-247-891-00
1-249-428-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
150K
330K
8.2K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R717
R718
R719
R720
R721
1-247-903-00
1-247-899-11
1-249-393-11
1-249-430-11
1-247-862-11
CARBON
CARBON
CARBON
CARBON
CARBON
1M
680K
10
12K
20K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R722
R723
R724
R725
R726
1-249-441-11
1-247-896-11
1-249-439-11
1-247-883-00
1-247-876-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
510K
68K
150K
75K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R727
R728
R729
R730
1-249-437-11
1-249-441-11
1-249-430-11
1-249-435-11
CARBON
CARBON
CARBON
CARBON
47K
100K
12K
33K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
R731
R734
R735
R736
R737
1-247-863-91
1-247-843-11
1-249-427-11
1-247-863-91
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
3.3K
6.8K
22K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R738
R801
R803
R804
R805
1-249-435-11
1-249-429-11
1-249-430-11
1-249-430-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
10K
12K
12K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R806
R807
R808
R809
R810
1-249-430-11
1-249-430-11
1-249-430-11
1-249-431-11
1-249-431-11
CARBON
CARBON
CARBON
CARBON
CARBON
12K
12K
12K
15K
15K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R811
R820
R821
R828
R843
1-249-431-11
1-249-417-11
1-247-807-31
1-247-815-91
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
15K
1K
100
220
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R845
R846
R847
R852
R853
1-247-843-11
1-249-417-11
1-249-429-11
1-247-903-00
1-247-887-00
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
1K
10K
1M
220K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R855
1-249-429-11 CARBON
10K
5%
1/4W
< VARIABLE RESISTOR >
1-228-995-00 RES, ADJ, METAL 22K (VCO)
1-225-438-11 RES, VAR, CARBON 20K/20K (TONE)
1-225-439-11 RES, VAR, CARBON 20K/20K (VOLUME)
< SWITCH >
– 42 –
1-571-345-11 SWITCH, LEVER SLIDE (FUNCTION)
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ver 1.1 1998.08
MAIN
Ref. No.
Part No.
Description
MONO/ST SW
Remark
POWER
REC SW
Ref. No.
Part No.
Description
*
1-668-282-11 VOL SEL BOARD (E,EA)
*************
VOL SEL
Remark
< TRANSFORMER >
T1
T2
T301
1-409-944-11 COIL (DET)
1-416-522-11 COIL (IFT)
1-416-041-11 TRANSFORMER, BIAS OSCILLATION
< SWITCH >
! S901
< VIBRATOR >
X801
1-760-793-11 VIBRATOR, CERAMIC (16.9344MHz)
************************************************************
1-552-921-00 SWITCH, POWER (VOLTAGE CHANGE)
(VOLTAGE SELECTOR)(E,EA)
************************************************************
MISCELLANEOUS
***************
1-668-288-21 MONO/ST SW BOARD (AEP,EE,IT,CIS,UK)
*****************
*
< CONNECTOR >
* CNP1
1-691-573-11 PIN, CONNECTOR (PC BOARD) 2P
(AEP,EE,IT,CIS,UK)
< SWITCH >
S302
1-771-060-11 SWITCH, SLIDE (FM MODE)
(AEP,EE,IT,CIS,UK)
************************************************************
56
73
107
! 254
255
1-452-899-11
1-777-955-11
1-533-233-31
8-848-483-05
X-2626-202-1
ANT1
! F901
! F902
1-501-883-11
1-532-467-31
1-532-464-31
! F902
1-533-618-11
1-668-284-11 POWER BOARD (US,CND, C&SA)
1-668-284-21 POWER BOARD (EXCEPT US,CND, C&SA)
*************
*
*
LCD800
HE301
HRP301
M601
M701
1-533-233-31 HOLDER, FUSE
< CAPACITOR >
C901
C902
C903
C904
1-101-005-00
1-101-005-00
1-101-005-00
1-101-005-00
CERAMIC
CERAMIC
CERAMIC
CERAMIC
22000PF
22000PF
22000PF
22000PF
S601
S801
SP301
SP302
! T901
50V
50V
50V
50V
! T901
! T901
! T901
< DIODE >
D901
D902
D903
D904
8-719-063-79
8-719-063-79
8-719-063-79
8-719-063-79
DIODE
DIODE
DIODE
DIODE
1N4002B
1N4002B
1N4002B
1N4002B
1-801-913-11
1-543-876-11
1-500-364-11
A-3304-619-A
X-2625-769-1
MAGNET
WIRE (FLAT TYPE) (16 CORE)
HOLDER, FUSE
OPTICAL PICK-UP KSS-213C
CHASSIS ASSY (MB) (RP), MOTOR
(INCLUDING M702) (SPINDLE)
ANTENNA, TELESCOPIC
FUSE, TIME LAG (T0.315AL/250V) (E,EA)
FUSE, TIME LAG (T2.5AL/250V)
(EXCEPT US,CND,C&SA)
FUSE, GLASS CYLINDERICAL (3.15A/250V)
(US,CND,C&SA)
DISPLAY PANEL, LIQUID CRYSTAL
HEAD (ERASE)
HEAD,MAGNETIC(RECORD/PLAYBACK)
MOTOR ASSY
GEAR ASSY (MB) (RP), MOTOR (SLED)
1-762-679-11
1-692-960-11
1-505-889-11
1-505-889-11
1-431-231-11
SWITCH, LEAF (MD POWER)
SWITCH, PUSH (1 KEY) (DOOR OPEN/CLOSE)
SPEAKER (10cm) (L-CH)
SPEAKER (10cm) (R-CH)
TRANSFORMER, POWER (AEP,EE,IT,CIS,UK,
SP,AR)
1-431-230-11 TRANSFORMER, POWER (US,C&SA)
1-431-230-21 TRANSFORMER, POWER (CND)
1-431-233-11 TRANSFORMER, POWER (E,EA)
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
< FUSE >
! F902
! F902
1-532-464-31 FUSE, TIME LAG (T2.5AL/250V)
(EXCEPT US,CND,C&SA)
1-533-618-11 FUSE, GLASS CYLINDERICAL (3.15A/250V)
(US,CND,C&SA)
!
!
!
!
!
< CABLE, HOLDER >
* KH904 1-573-287-11 HOLDER, CABLE 2P
************************************************************
*
*
1-668-287-11 REC SW BOARD (US,CND, C&SA)
1-668-287-21 REC SW BOARD (EXCEPT US,CND, C&SA)
*************
1-557-287-11
1-475-664-11
1-696-818-11
1-696-820-21
1-770-019-11
CORD, POWER (C&SA)
ADAPTOR, CONVERSION (2P) (E,EA)
CORD, POWER (US,CND)
CORD, POWER (E,AEP,EE,IT,CIS,UK,SP,EA)
ADAPTOR, CONVERSION PLUG 3P (UK)
3-861-410-11 MANUAL, INSTRUCTION (ENGLISH)
(US,CND,C&SA)
3-861-410-21 MANUAL, INSTRUCTION (FRENCH) (CND)
3-861-410-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH)
(E,AEP,EE,UK,SP,EA)
3-861-410-41 MANUAL, INSTRUCTION (FRENCH, GERMAN)
(AEP,SP,EA)
3-861-410-51 MANUAL, INSTRUCTION (DUTCH,
PORTUGUESE)(E,AEP)
< SWITCH >
S301
1-762-565-11 SWITCH, SLIDE (REC/PB)
************************************************************
– 43 –
3-861-410-61 MANUAL, INSTRUCTION (ITALIAN) (IT)
3-861-410-71 MANUAL, INSTRUCTION (POLISH, CZECH,
HUNGARIAN) (CIS)
3-861-410-81 MANUAL, INSTRUCTION (FINNISH, SWEDISH)
(CIS)
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
CFD-V15/V24
Ref. No.
Part No.
Description
Remark
3-861-410-91 MANUAL, INSTRUCTION (RUSSIAN) (EE)
3-861-411-11 MANUAL, INSTRUCTION (SPANISH) (C&SA)
************************************************************
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-647-79
7-685-533-19
7-682-548-04
7-621-773-95
7-621-255-15
SCREW +BVTP 3X10 TYPE2 N-S
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW +B 3X8
SCREW +B 2.6X6
SCREW +P 2X3
#6
#7
#8
#10
#11
7-685-649-79
7-621-770-87
7-685-646-79
7-685-648-79
7-685-649-14
SCREW +BVTP 3X14 TYPE2 N-S
SCREW +B 2.6X5
SCREW +BVTP 3X8 TYPE2 N-S
SCREW +BVTP 3X12 BZN-N
SCREW +BVTP 3X14
#12
7-685-648-14 SCREW +BVTP 3X12
Sony Corporation
9-923-320-11
Personal A&V Products Company
– 44 –
98B0290-1
Printed in Japan © 1998.2
Published by Quality Engineering Dept.
(Shibaura)
CFD-V15/ V24
US Model
Canadian Model
SERVICE MANUAL
CFD-V15
AEP Model
UK Model
1998. 06
CFD-V24
E Model
CFD-V15/V24
SUPPLEMENT - 1
File this Supplement with the Service Manual.
Subject :
CHANGE OF EXPLODED VIEWS PARTS LIST
(ECN-RC800384)
r
CHANGE OF EXPLODED VIEWS PARTS LIST (Page 32 – 34)
page
Before Change
Ref. No.
32
33
34
r
• Abbreviation
CND : Canadian
SP : Singapore
EA
: Saudi Arabia IT
: Italian
EE
: East European CIS : Russian
C&SA : Central and South America
After Change
remark
Part No.
Description
remark
X-3375-386-1
X-3375-390-1
X-3375-392-1
X-3375-394-1
CABINET (FRONT) SUB ASSY (SILVER)(AEP,UK,CIS,SP)
CABINET (FRONT) SUB ASSY (SILVER) (EA)
CABINET (FRONT) SUB ASSY (DARK GRAY) (EE)
CABINET (FRONT) SUB ASSY (DARK GRAY)
(CND,C&SA)
CABINET (FRONT) SUB ASSY (DARK GRAY) (IT)
CABINET (FRONT) SUB ASSY (DARK GRAY) (E)
CABINET (FRONT) SUB ASSY (DARK GRAY)
(AEP, UK, CIS)
CABINET (FRONT) SUB ASSY (SILVER) (EE)
––––––––––––––
Part No.
Description
1
1
1
1
X-3375-386-1
X-3375-390-1
X-3375-392-1
X-3375-394-1
CABINET (FRONT) SUB ASSY (SP)
CABINET (FRONT) SUB ASSY (EA)
CABINET (FRONT) SUB ASSY (EE)
CABINET (FRONT) SUB ASSY (C&SA)
1
1
1
X-3375-395-1
X-3375-396-1
X-3375-400-1
1
X-3375-395-1 CABINET (FRONT) SUB ASSY (IT)
X-3375-396-1 CABINET (FRONT) SUB ASSY (E)
X-3375-400-1 CABINET (FRONT) SUB ASSY
(AEP, UK, CIS)
––––––––––––––
X-4949-821-1 CABINET (FRONT) SUB ASSY (CND)
2
3-018-837-11 KNOB (VOL) (SP,EA)
3-018-837-11 KNOB (VOL) (SLIVER) (AEP,UK,CIS,EE,SP,EA)
5
3-018-840-11 KNOB (TU) (SP,EA)
3-018-840-11 KNOB (TU) (SLIVER) (AEP,UK,CIS,EE,SP,EA)
58
X-3375-399-1 HOLDER SUB ASSY, CASSETTE
X-3375-399-1 HOLDER SUB ASSY, CASSETTE (DARK GRAY, SILVER)
103
3-009-194-41 KNOB (FUN) (SP,EA)
3-009-194-41 KNOB (FUN) (SILVER) (SP,EA,AEP,UK,CIS,EE)
106
106
106
106
106
X-3375-384-1
X-3375-387-1
X-3375-391-1
X-3375-393-1
X-3375-401-1
X-3375-384-1 CABINET (REAR) (DARK GRAY) (CND,C&SA)
––––––––––––––
X-3375-391-1 CABINET (REAR) (DARK GRAY) (EA,E)
X-3375-393-1 CABINET (REAR) (DARK GRAY) (EE,CIS,SP)
X-3375-401-1 CABINET (REAR) (DARK GRAY) (AEP,IT,UK)
CABINET (REAR) (CND, C&SA)
CABINET (REAR) (SP)
CABINET (REAR) (EA,E)
CABINET (REAR) (EE)
CABINET (REAR) (AEP,IT,UK,CIS)
X-3375-955-1
CORRECTION
!
: indicates corrected portion
page
Incorrect
Ref. No.
43
255
Part No.
Description
Correct
remark
X-2626-201-1 CHASSIS ASSY (MB) (RP), MOTOR
(INCLUDING M702) (SPINDLE)
Part No.
Description
X-2626-202-1 CHASSIS ASSY (MB) (RP), MOTOR
(INCLUDING M702) (SPINDLE)
$
Sony Corporation
9-923-320-81
remark
Personal A&V Products Company
98F0291-1
Printed in Japan © 1998.6
Published by Quality Engineering Dept.
(Shibaura)
CFD-V15/V24
US Model
Canadian Model
SERVICE MANUAL
CFD-V15
AEP Model
UK Model
1998. 08
CFD-V24
E Model
CFD-V15/V24
SUPPLEMENT - 2
File this Supplement with the Service Manual and Supplement-1.
Subject :
r ARGENTINA MODEL HAS BEEN ADDED FOR CFD-V24
r CHANGE OF PARTS LIST
(ECN-RC800167/RC800540)
• Abbreviation
CND : Canadian
SP : Singapore
EA
: Saudi Arabia
IT : Italian
EE
: East European CIS : Russian
AR : Argentina
C&SA : Central and South America
The CFD-V24 (Argentina model) is approximately the same as the CFD-V24 (Singapore model).
Consequently, only difference between CFD-V24 (Argentina model) and CFD-V24 (Singapore model) are listed.
For other informations, please refer to the previously issued CFD-V15/V24 service manual (9-923-320-11) and Supplement-1
(9-923-320-81).
r
DIFFERENCE PARTS LIST
ACCESSORIES & PACKING MATERIALS (Service Manual See page 43)
CFD-V24 : Singapore Model
Part No.
Description
CFD-V24 : Argentina Model
Part No.
Description
! 1-783-952-21
! 1-696-820-21 CORD, POWER (E,AEP,EE,IT,CIS,UK,SP,EA)
3-861-410-31
3-861-410-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(E,AEP,EE,UK,SP,EA)
3-861-410-41 MANUAL, INSTRUCTION (FRENCH,GERMAN) (AEP,SP,EA)
r
CORD, POWER (AR)
MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(E,AEP,EE,UK,SP,EA,AR)
–––––––––––––––––
CHANGED PARTS LIST
EXPLODED VIEWS (Service Manual See page 33 to 36, 43)
Page
33
34, 43
35
36
Before Change
Ref. No.
71
72
! F902
! F902
Part No.
Description
After Change
Remark
3-910-095-11 RUBBER, VIBRATION PROOF (RED)
3-910-095-01 RUBBER, VIBRATION PROOF (GREEN)
––––––––––––
1-532-464-31 FUSE, TIME LAG (T2.5AL/250V)
(EXCEPT US,CND,C&SA)
* 161
3-008-589-01 SLIDER (FF)
168
3-934-834-01 SPRING (BT)
HRP301 1-500-364-11 HEAD, MAGNETIC (RECORD/PLAYBACK)
M601
A-3304-619-A MOTOR ASSY
Part No.
Description
3-910-095-31
3-910-095-21
1-532-338-31
1-532-464-31
RUBBER, VIBRATION PROOF (RED)
RUBBER, VIBRATION PROOF (GREEN)
FUSE, TIME LAG (T2.0AL/250V) (E,EA)
FUSE, TIME LAG (T2.5AL/250V)
(EXCEPT US,CND,C&SA,E,EA)
SLIDER (FF)
SPRING (BT)
HEAD, MAGNETIC (RECORD/PLAYBACK)
MOTOR ASSY
3-008-589-13
3-022-794-02
1-500-454-11
A-3320-446-A
Remark
ELECTRICAL PARTS LIST (Service Manual See page 39 to 43)
Page
Before Change
Ref. No.
Part No.
After Change
Description
Remark
Part No.
Description
1-104-664-11 ELECT
C17
1-124-443-00 ELECT
100uF
20%
10V
C20
1-162-306-11 CERAMIC
0.01uF
20%
16V
1-124-443-00 ELECT
1-162-306-11 CERAMIC
1-124-902-00 ELECT
39
C108
1-124-902-00 ELECT
0.47uF
20%
C122
1-161-057-00 CERAMIC
0.033uF
10%
C122
1-162-843-11 CERAMIC
0.022uF
50V
50V
(EA,SP)
10%
16V
(EXCEPT EA,SP)
1-126-956-91 ELECT
1-161-057-00 CERAMIC
1-162-843-11 CERAMIC
1-124-902-00 ELECT
C208
1-124-902-00 ELECT
0.47uF
20%
C222
1-161-057-00 CERAMIC
0.033uF
10%
C222
1-162-843-11
C715
C827
C827
1-124-903-11
1-162-282-31
1-162-286-21
L1
L1
R124
1-406-998-11
1-406-999-11
1-249-413-11
R124
1-249-417-11
R124
1-249-421-11
R155
R224
1-249-431-11
1-249-413-11
R224
1-249-417-11
R224
1-249-421-11
R255
! R340
1-249-431-11
1-249-381-11
*
1-668-288-21 MONO/ST SW BOARD (AEP,EE,IT,CIS,UK)
******************
40
41
42
43
* CNP1
S302
50V
50V
(EA,SP)
CERAMIC
0.022uF 10%
16V
(EXCEPT EA,SP)
ELECT
1uF
20%
50V
CERAMIC
100PF
10%
50V
CERAMIC
220PF
10%
50V
(C&SA,SP)
COIL, AIR-CORE (US,CND,C&SA)
COIL, AIR-CORE (AEP,IT,CIS,UK,SP,EA,E)
CARBON
470
5%
1/4W
(EA,SP)
CARBON
1K
5%
1/4W
(C&SA,E)
CARBON
2.2K
5%
1/4W
(EXCEPT C&SA,E,EA,SP)
CARBON
15K
5%
1/4W
CARBON
470
5%
1/4W
(EA,SP)
CARBON
1K
5%
1/4W
(C&SA,E)
CARBON
2.2K
5%
1/4W
(EXCEPT C&SA,E,EA,SP)
CARBON
15K
5%
1/4W
CARBON
1
5%
1/4W F
(US)
1-126-956-91 ELECT
1-161-057-00 CERAMIC
1-162-843-11 CERAMIC
Remark
47uF
20%
10V
(US,CND,C&SA)
100uF
20%
10V
(EXCEPT US,CND,C&SA)
0.01uF
20%
16V
(EXCEPT US,CND,C&SA)
0.47uF
20%
50V
(EXCEPT EE)
0.1uF
20%
50V
(EE)
0.033uF 10%
50V
(EA,SP,E,C&SA,AR)
0.022uF 10%
16V
(EXCEPT EA,SP,E,C&SA,AR)
0.47uF
20%
50V
(EXCEPT EE)
0.1uF
20%
50V
(EE)
0.033uF 10%
50V
(EA,SP,E,C&SA,AR)
0.022uF 10%
16V
(EXCEPT EA,SP,E,C&SA,AR)
1-124-907-11 ELECT
10uF
20%
50V
–––––––––––––––
1-162-286-21 CERAMIC
220PF
10%
50V
1-406-998-11 COIL, AIR-CORE (US,CND,C&SA,E)
1-406-999-11 COIL, AIR-CORE (AEP,IT,CIS,UK,SP,EA,AR)
1-249-413-11 CARBON
470
5%
1/4W
(EA,SP,E,C&SA,AR)
–––––––––––––––
1-249-421-11 CARBON
1-249-429-11 CARBON
1-249-413-11 CARBON
2.2K
5%
1/4W
(EXCEPT EA,SP,E,C&SA,AR)
10K
5%
1/4W
470
5%
1/4W
(EA,SP,E,C&SA,AR)
–––––––––––––––
1-249-421-11 CARBON
1-249-429-11 CARBON
2.2K
5%
1/4W
(EXCEPT EA,SP,E,C&SA,AR)
10K
5%
1/4W
–––––––––––––––
*1-668-288-21 MONO/ST SW BOARD
(AEP,EE,IT,CIS,UK,SP,AR)
******************
1-691-573-11 PIN,CONNECTOR (PC BOARD) 2P
*1-691-573-11 PIN,CONNECTOR (PC BOARD) 2P
(AEP,EE,IT,CIS,UK)
(AEP,EE,IT,CIS,UK,SP,AR)
1-771-060-11 SWITCH,SLIDE (FM MODE) (AEP,EE,IT,CIS,UK)
1-771-060-11 SWITCH,SLIDE (FM MODE) (AEP,EE,IT,CIS,UK,
SP,AR)
–2–
r
ACCESSORIES & PACKING MATERIALS
Page
43
r
Part No.
Description
!
1-557-287-11 CORD, POWER (C&SA)
After Change
Remark
Part No.
Description
Remark
1-559-047-31 CORD, POWER (C&SA)
HARDWARE LIST
Page
44
r
Before Change
Ref. No.
Before Change
Ref. No.
#4
Part No.
Description
After Change
Remark
7-621-773-95 SCREW +B 2.6X6
Part No.
Description
7-621-775-20 SCREW +B 2.6X5
CORRECTION
PRINTED WIRING BOARDS (Service Manual See page 18, 19)
! : Indicates corrected portion
(Location : 8 to 12, D to H)
$
#
$
#
–3–
Remark
CFD-V15/V24
EXPLODED VIEWS (Service Manual See page 34, 43)
! : Indicates corrected portion
Page
34, 43
43
INCORRECT
CORRECT
Ref. No.
Part No.
! T901
1-426-632-11 TRANSFORMER, POWER (AEP,EE,IT,CIS,UK,SP)
Description
Remark
!
!
1-569-008-11 ADAPTOR, CONVERSION (2P) (E,EA)
1-590-147-11 CORD, POWER (US,CND)
Part No.
Sony Corporation
9-923-320-82
Personal A&V Products Company
–4–
Description
Remark
1-431-231-11 TRANSFORMER, POWER
(AEP,EE,IT,CIS,UK,SP,AR)
1-475-664-11 ADAPTOR, CONVERSION (2P) (E,EA)
1-696-818-11 CORD, POWER (US,CND)
98H0290-1
Printed in Japan © 1998.8
Published by Quality Engineering Dept.
(Shibaura)