Download SERVICE MANUAL - MiniDisc Community Page

ZS-M7
SERVICE MANUAL
US Model
AEP Model
UK Model
Tourist Model
Ver 1.2 2001.07
With SUPPLEMENT 1
(9-923-346-82)
Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trademarks of
Dolby Laboratories Licensing Corporation.
MD
Section
CD
Section
Model Name Using Similar Mechanism
NEW
MD Mechanism Type
MDM-3EG
Optical Pick-up Type
KMS-260A
Model Name Using Similar Mechanism
NEW
MD Mechanism Type
CDM-2411AAA
Optical Pick-up Type
DAX-11A
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
With 4-ohm loads, both channels driven from 100 – 10,000 Hz ; rated 7W
per channel-minimum RMS power, with no more
than 10% total harmonic distortion in AC operation (US Model).
CD player Section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration : Continuous
Laser output : Less than 44.6 µW
(This output is the value measured at a distance of about 200
mm from the objective lens surface on the optical pick-up
block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of programme positions
2
Frequency response
20 – 20,000 Hz +1 /–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
US Model :
FM : 87.6 – 108 MHz
AM : 530 – 1,710 kHz
9-923-346-12
Sony Corporation
2001G0200-1
© 2001.7
Personal Audio Company
Shinagawa Tec Service Manual Production Group
EXCEPT US Model :
FM : 87.6 – 107 MHz
MW : 531 – 1,602 kHz
LW : 153 – 279 kHz
IF
FM : 10.7 MHz
MW/LW : 450 kHz
Aerials
FM : Telescopic areal
Extension areal terminal
AM : Extension areal terminals (US Model)
MW/LW : Extension areal terminals (EXCEPT US Model)
MD player section
System
Minidisc digital audio system
Disc
MiniDisc
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration : Continuous
Laser output : Less than 44.6 µW
(This output is the value measured at a distance of about 200
mm from the objective lens surface on the optical pick-up
block with 7 mm aperture.)
– Continued on page 2 –
PERSONAL MINIDISC SYSTEM
Outputs
Recording/Playback time
Maximum 74 minutes (with MDW-74)
Revolutions
400 rpm to 900 rpm (CLV)
Error correction
Advanced Cross Interleave Reed Solomon Code (ACIRC)
Sampling frequency
44.1 kHz
Cording Adaptive Transform Acoustic Cording (ATRAC)
Modulation system
EFM (Eight-to-Fourteen Modulation)
Number of programme positions
2 stereo programme positions
Frequency response
20 – 20,000 Hz +1 /–2 dB
Signal-to-noise ratio
Over 80 dB (during playback)
Wow and flutter
Below measurable limit
Headphones jack (stereo minijack) (2) : For 32 ohms
impedance headphones
Power outputs
7W+7W
Power requirements
For personal minidisc system :
US Model :120V AC, 60Hz
EXCEPT US Model :230V AC, 50Hz
For remote commander :
3V DC, 2 size AA (R6) batteries
Power consumption
30 W
Dimensions (incl. projecting parts)
Approx. 528 x 275 x 139 mm (w/h/d)
(20 7/8 x 10 7/8 x 5 1/2 inches)
Mass
approx. 6.4 kg (14 lb. 2 oz)
Supplied accessories
Remote commander (1)
AM loop aerial (1) (US Model)
MW/LW loop aerial (1) (EXCEPT US Model)
Speaker nets (2) (EXCEPT US Model)
General
Speaker
Full range : 8 cm (3 in.) dia., 4ohms, cone type (2)
Inputs
Design and specifications are subject to change without notice.
LINE IN (stereo minijack) : Sensitivity 436 mV/691 mV
TABLE OF CONTENTS
5-6. Laser Power Adjustment ...........................................
5-7. Traverse Adjustment .................................................
5-8. Focus Bias Adjustment .............................................
5-9. Error Rate Check ......................................................
5-10. Focus Bias Check ...................................................
5-11. Adjustment and Connection Locations ...................
Specifications ........................................................................... 1
1. SERVICE NOTE ........................................................... 3
2. GENERAL ...................................................................... 5
3. DISASSEMBLY
3-1. Cabinet (Front) ASSY, Cabinet (Rear) ASSY ..........
3-2. Left Key Board, Front Key Board, Top Key board,
Right Key Board, Relay Board .................................
3-3. FL Board, Trans Board .............................................
3-4. Tuner Board, FM ANT Board, AM ANT Board .......
3-5. MD Chassis ASSY ...................................................
3-6. MD Block ASSY, Filter Board .................................
3-7. Audio Board, HP Board, Line in Board ....................
3-8. Main Board, CD Block ASSY ..................................
3-9. Shield Case (Top), Shield Case (Bottom) .................
3-10. DG Board, BD Board, MD Mechanism Deck ........
3-11. Shutter ASSY ..........................................................
3-12. SW Board ...............................................................
3-13. Slider ASSY, “Head, Over Write” ..........................
3-14. MD Optical Pick-up Block .....................................
3-15. Loading Board, “Tray ASSY, CD” .........................
3-16. CD Optical Pick-up Block, Pick-up Relay Board ..
21
6. DIAGRAMS
6-1. Explanation of IC Terminals .....................................
6-2. Block Diagram (1) ....................................................
6-3. Block Diagram (2) ....................................................
6-4. Printed Wiring Boards –Main Section – ...................
6-5. Schematic Diagram –Main Section (1/2) – ..............
6-6. Schematic Diagram –Main Section (2/2) – ..............
6-7. Printed Wiring Boards
–Tuner Section (US Model) – ..................................
6-8. Schematic Diagram
–Tuner Section (US Model) – ...................................
6-9. Printed Wiring Boards
–Tuner Section (EXCEPT US Model) – ...................
6-10. Schematic Diagram
–Tuner Section (EXCEPT US Model) – ..................
6-11. Schematic Diagram –BD Section – ........................
6-12. Printed Wiring Boards –BD Section – ....................
6-13. Schematic Diagram –Power Section – ...................
6-14. Printed Wiring Boards –Power Section – ...............
6-15. Schematic Diagram –DG Section – ........................
6-16. Printed Wiring Boards –DG Section – ...................
6-17. Printed Wiring Boards –Front Key Section – .........
6-18. Schematic Diagram –Front Key Section – .............
22
22
23
23
24
24
25
25
26
26
27
27
28
29
29
4. TEST MODE
4-1. Caution When Using the Test Mode .........................
4-2. Test Mode Settings ...................................................
4-3. Releasing the Test Mode ...........................................
4-4. Basic Operations of the Test Mode ...........................
4-5. Selecting the Test Mode ............................................
4-6. Functions of Other Buttons ......................................
4-7 Test Mode Display .....................................................
30
30
30
30
30
31
31
67
69
72
74
77
79
82
85
87
90
93
97
7-1. Front Cabinet Section ............................................. 106
7-2. Rear Cabinet Section .............................................. 107
7-3. Chassis Section ....................................................... 108
7-4. MD Section (1) ....................................................... 109
7-5. MD Section (2) ........................................................ 110
7-6. CD Section ............................................................... 111
7-7. Optical Pick-up Section ........................................... 112
32
32
32
32
33
39
46
49
55
59
63
7. EXPLODED VIEWS
5. ADJUSTMENTS
5-1. Cautions When Checking Laser Diode Emission .....
5-2. Cautions When Handling
the Optical Pick-up (KSM-260A) ............................
5-3. Cautions During Adjustment ....................................
5-4. Creating a Continuous Recording Disk ....................
5-5. Temperature Compensation Offset Adjustment ........
33
33
34
35
35
35
8. ELECTRICAL PARTS LIST .................................. 113
–2–
SECTION 1
SERVICE NOTE
SAFETY CHECK-OUT (US Model)
After correcting the original service problem, perform the following safety check before releasing the set to the customer :
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75V,
so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5kΩ
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Close the lid for CD.
2. Press CD ^ button.
3. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
CAUTION DURING WHEN MOUNTING THE PULLEY
FOR THE LOADING MOTOR
Make the following adjustment when mounting the loading motor
(part number : 1-698-999-11) and motor pulley (part number : 2627-174-01) of the CD section.
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK !ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
–3–
Specification : A = 0.9 to 1.1mm
ABOUT THE BD BOARD WAVEFORM CHECKING JIG
The special jig (J-2501-124-A) is highly convenient when checking the waveform of the BD board of the MD section. Pin names
and items to check are as follows:
I+3V : for IOP measurement (check for depleted optical pickup
laser)
IOP : for IOP measurement (check for depleted optical pickup
laser)
TEO : TRK error signal (traverse adjustment)
VC : Standard level for checking signals
RF : RF signal (jitter check)
MD block section
DG board
IOP
I + 3V
VC
TEO
RF
CN110
BD board
Jig
(J-2501-124-A)
ABOUT THE HARDWARE RESET
It is possible to reset the system microcomputer by pressing the
RESET button located on the rear with a pointed object. Use this
button when the unit cannot be operated properly due to such problems as microcomputer errors, etc.
–4–
RESET button
1 CD (MD SYNCHRO REC button
DISC ALL
REC IT : TO TOP
TO END
2 MD insert section
3 TUNE–, + • 0, ) •ı, ∫button
4 EDIT button
5 DELETE button
6 INSERT button
7 AUTO PRESET•SHUF/PGM button
8 LINE LEVEL•MONO/ST•REPEAT button
9 ENTER•YES button
!º Jog dial
=/+ AMS
PRESET
FRONT PANEL : RADIO section
–5–
!•
!∞
!§
!¶
!¡
!™
!£
!¢
CANCEL•NO button
6 MD EJECT button
6 CD OPEN/CLOSE button
CD operation buttons
^ (play/pause)
p (stop)
CD tray
BAND button
MD operation button
^ (play/pause)
p (stop)
REC button
LOCATION AND FUNCTION OF CONTROLS
!ª POWER button (US MODEL)
OPERATE button (EXCEPT US MODEL)
@º SLEEP button
@¡ STANDBY button
@™ TIMER button
@£ CLOCK button
@¢ Display window
FRONT PANEL : TIMER • COM section
@∞
@§
@¶
@•
@ª
#º
#¡
BASS/TREBLE button
MEGA BASS button
VOLUM –, + button
DISPLAY button
2 (Headphones) Jack (stereo mini jack)
LINE button
Remote control receiver section
SECTION 2
GENERAL
–6–
1
2
3
4
5
6
7
SLEEP button
CD OPEN/CLOSE button
Number button
MODE button
BASS/TREBLE+, – button
MEGA BASS button
MD operation button
( (play)
P (pause)
p (stop)
r (REC)
REMOTE CONTROL
8 CD operation button
( (play)
P (pause)
p (stop)
9 Radio operation button
BAND
TUNER –, +
!º POWER button(US MODEL)
OPERATE button (EXCEPT US MODEL)
!¡ VOL +, – button
!™ =, + (AMS/SERCH) button
#•
EXCEPT US Model
#£
REAR PANEL section
#™ AM ANTENNA terminal
MW(LW) ANTENNA terminal
#£ FM EXT ANTENNA terminal (US model)
ANTENNA SELECTOR switch (Except US model)
#¢ LINE IN (Analog) terminal
#∞ Antenna
#§ RESET button
#¶ Power cord
#• FM EXT ANTENNA terminal (Except US model)
This section is extracted from
instruction manual.
–7–
–8–
–9–
– 10 –
– 11 –
– 12 –
– 13 –
– 14 –
– 15 –
– 16 –
– 17 –
– 18 –
– 19 –
– 20 –
SECTION 3
DISASSEMBLY
r
The equipment can be removed using the following procedure.
< MAIN BLOCK SECTION >
Set
Cabinet (Front)
ASSY
Left key board, Front key board, Top key board, Right board, Relay board
Cabinet (Rear)
ASSY
FL board, Trans board, Tuner board, FM ANT board, AM ANT board
MD chassis ASSY
MD Block ASSY, Filter board
Audio board, HP board, Line in board
Main board
CD block ASSY
< MD BLOCK SECTION >
MD Block ASSY
Shiled case
(Top, Bottom)
DG board
BD board
Sub chassis ASSY
Shutter ASSY
MD mechanism deck
SW board, Slider ASSY, “Head, Over wright”
MD Optical pick-up block
< CD BLOCK SECTION >
CD block ASSY
Loading board
“Tray ASSY, CD”
CD Optical pick-up block, Pick-up relay board
Note : Follow the disassembly procedure in the numerical order given.
< MAIN BLOCK SECTION >
3-1. CABINET (FRONT) ASSY, CABINET (REAR) ASSY
3 Screws (2.6X10)
6 CN353 (4 pin)
(Audio board)
2 Screws (+BVTP 3X12)
4 Screws (3X45)
5
1
3 Screws (2.6X10)
Cabinet (Rear) ASSY
2 Screws
(+BVTP 3X12)
7 CN410 (11 pin)
(Relay board)
1
Net (L) ASSY, SP
Cabinet (Front) ASSY
2 Screws (+BVTP 3X12)
Net (R) ASSY, SP
– 21 –
3-2. LEFT KEY BOARD, FRONT KEY BOARD, TOP KEY BOARD, RIGHT KEY BOARD, RELAY BOARD
3 Screws (2.6X8)
Front key board
5 Screws (2.6X8)
1 Screws ( 2.6X8)
Button (MEGA BASS)
Left key board
6
8
2
Top key board
4
7 Screw (M1.7X5)
!º
9 Screws (2.6X8)
Right key board
!™
!¡ Screws (2.6X8)
Relay board
Cabinet (Front) ASSY
3-3. FL BOARD, TRANS BOARD
2 Screws (2.6X8)
FL board
1 Wire parallel
(FFC)(15 core)
3
Cabinet (Rear) ASSY
2 Screws (2.6X8)
4 CN954 (4 pin)
5 Screws
(+BVTP 3X16)
6
4 CN951 (6 pin)
8
4 CN952 (6 pin)
7 Screws
(+BVTP 4X12)
Bracket
(Trans)
5 Screws
(+BVTP 3X16)
Trans board
– 22 –
3-4. TUNER BOARD, FM ANT BOARD, AM ANT BOARD
Cabinet (Rear) ASSY
EXCEPT US model
7 Screws
(+BVTP 3X12)
3Screws
(+BTP 3X12)
FM ANT board
5 Screws
(+BVTP 3X12)
8
!º
Tuner board
4
AM ANT
board
1 Wire parallel (FFC)
(13core)
6
2 Screws
(+BVTP 3X12)
9 Screws
(+BVTP 3X12)
Bracket (Tuner)
3-5. MD CHASSIS ASSY
2 Screws (2.6X8)
MD chassis ASSY
4
Cabinet (Rear) ASSY
3 Screws (+BVTP 3X12)
1 Screws (+BVTP 3X12)
– 23 –
3-6. MD BLOCK ASSY, FILTER BOARD
MD Block ASSY
3 Screws
(M1.7X5)
2 CN703
(2 pin)
5 Wire, Parallel (FFC) (26 core)
4
7
Filter board
1 Wire, Parallel (FFC) (26 core)
3 Screws
(M1.7X5)
6 Screws
MD chassis
3-7. AUDIO BOARD, HP BOARD, LINE IN BOARD
3 Screws
(+BVTP 3X16)
Audio board
1 Screw
(+BVTP 3X12)
3 Screws
(+BVTP 3X12)
4
Chassis (Audio)
1 Screw
(+BVTP 3X12)
2
5 Screw
(+BVTP 3X12)
HP board
6
8
Line in board
7 Screws
(+BVTP 3X12)
MD Chassis
– 24 –
3-8. MAIN BOARD, CD BLOCK ASSY
5 Screws (+BVTP 3X12)
3 Screws (2.6X8)
4
6
Main board
MD Chassis
1 CN701 Wire, Parallel (FFC)(21 core)
(Main board)
2 CN803 (5pin)
(Main board)
CD Block ASSY
< MD BLOCK SECTION >
3-9 . SHIELD CASE (TOP), SHIELD CASE (BOTTOM)
1 Screws (M1.7X2)
Shield case (Top)
1 Screws (M1.7X2)
1 Screws
(M1.7X2)
1 Screws (M1.7X2)
2
MD mechanism deck
MD mechanism deck
Shield case (bottom)
3 Screws
(+BVTT 2X3)
Shield case (bottom)
4
• Note
Insert the projected sections of the MD
mechanism into the grooves on the bottom
of the shield case.
3 Screws (+BVTT 2X3)
– 25 –
3-10 . DG BOARD, BD BOARD, MD MECHANISM DECK
7 Step screw
7 Step screw
Insulator
Insulator
A
OK
A
MD mechanism deck
A
NG
8
When mounting, make sure that A
sets in the correct position
Sub chassis ASSY
BD board
6
2 Wire, Parallel (FFC)(19core)
5 Screw
(+BVTT 2X4)
4
DG board
1 Wire, Parallel
(FFC)(29core)
3 Screw
(+BVTT 2X4)
3-11 . SHUTTER ASSY
1 Washer
Sub chassis ASSY
2 Shaft (shutter)
Shutter ASSY
3 Shutter ASSY
Shaft (lid)
Hole B
Shaft (shutter)
Hole A
First mount the shaft (shutter) to hole A sets in the
diagram, then mount the shaft (lid) to hole B
– 26 –
3-12 . SW BOARD
SW board
1 Claws
2
1 Claws
1 Claws
MD mechanism deck
3-13. SLIDER ASSY, “ HEAD, OVER WRITE ”
2 Screw (M1.7X6)
Head, Over write
1 Screw (M1.7X2)
Claw
Slider ASSY
3
Retainer
6 Position the gear shaft
(L) as ahown in the diagram
Claw
7 While removing the claw(2 locations),
remove the slider assembly in direction
of the arrow.
4 Screw
(M1.7X2)
– 27 –
5 Retainer (Gear)
r
CAUTION DURING SLIDER ASSY ASSEMBLY
Slider ASSY
Mount the A of the lever (head up) so that it
passes above the slider ASSY.
A
OK
NG
Take caution as to not damage
the detection switch
3-14. MD OPTICAL PICK-UP BLOCK
MD Optical pick-up block
3
2
Shaft (Main shaft)
1 Remove the lever
– 28 –
< CD BLOCK SECTION >
3-15. LOADING BOARD, “TRAY ASSY, CD”
5 Screws
(+BVTP 3X10)
3 Screws
(+BVTP 3X10)
Plate (L), Side
1 Screws
(+BVTP 3X10)
Loading chassis
4
2
Cover (L), Side
Loading board
6
Plate (R), Side
Slider(L)
6
4
3 Screws
(+BVTP 3X10)
Wier, Parallel (FFC)(21 coer)
(Main board CM701)
Slider(R)
7
5 Screws
(+BVTP 3X10)
Lid, CD
Cover (R), Side
Tray ASSY, CD
3-16. CD OPTICAL PICK-UP BLOCK, PICK-UP RELAY BOARD
Tray (Top), CD
4 Wire, Parallel (FFC)(21core)
2
CD Optical pick-up block
5 Claw
6
3
5 Claw
Pick-up relay board
Tray (Bottom), CD
1 Screws (+BTP 2.6X8)
– 29 –
SECTION 4
TEST MODE
4-1. CAUTIONS WHEN USING THE TEST MODE
4-5. SELECTING THE TEST MODE
1 Check to make sure the inserted disk is completed stopped before removing since loading related operations will operate regardless of the Test mode operation.
The rotation of the inserted disk will not stop even when pressing the MD EJECT button during continuous playback and continuous recording.
In this case, the disk will be ejected while still in motion.
Always press the CANCEL/NO button and check to see that
the disk has stopped turning before pressing the MD EJECT
button.
2 In the Test mode, detection of the write-protect tab is executed.
For this reason, pressing the REC button in modes where the
recording laser is emitted (see 3-1-1) will delete the recorded
contents regardless of the tab position. When using a disk in the
Test mode which its contents must not be deleted, avoid entering the Continuous Recording mode and Transverse Adjustment
mode.
There are 9 types of test modes (see table below). Turning the AMS
dial clockwise switches modes shown in the table in the order from
top to bottom. Turning the AMS dial counterclockwise switches
modes shown in the table in the reverse order.
4-1-1. Modes which the record laser is emitted and
button operations
• Continuous Recording mode (CREC MODE)
• Traverse Adjustment mode (EFBAL ADJUST)
• Laser Power Adjustment mode (LDPWR ADJUST)
• Laser Power Check mode (LDPWR CHECK)
• Traverse (MO) check (EF MO CHECK)
• Traverse (MO) adjustment (EF MO ADJUST)
• When pressing the REC button
• For details on each adjustment mode, see respective items of SECTION 5. ADJUSTMENT
• If you have accidently entered another mode, press the CANCEL/
No button to exit.
• The EEP MODE is not used during servicing. Thus, details on
this mode are not given. If this mode is accidently entered, exit
immediately by pressing the CANCEL/NO button as the unit may
not operate correctly if the non-volatile storage memory being
overwritten.
4-2. TEST MODE SETTINGS
MD Test mode :
Press and hold the EDIT button and BASS/TREBLE button,
then press MD ^ n MD p n MD ^ n MD p.
CD Test mode :
Press and hold the EDIT button and BASS/TREBLE button,
then press CD ^ n CD p n CD ^ n CD p.
Display Test mode :
Press and hold the EDIT button and BASS/TREBLE button,
then press BAND n LINE n BAND n LINE (FUNCTION
is LINE).
Note 1 : Each test mode can be entered regardless of whether the power is
on or off. However, it is not possible to enter the test mode of the
particular function being operated. For example, it its not possible to enter the CD Test mode when the CD is in function.
Note 2 : When entering the MD Test mode, EEPROM data for the radio
broadcasting station names are automatically cleared. To exit the
MD Test mode with sufficient memory, always use the RESET
button. Moreover, never make radio presets once in the MD Test
mode until the mode is exited.
Display
Press the RESET button located on the rear.
4-4. BASIC OPERATIONS OF THE TEST MODE
ENTER/YES button
Used to advance and confirm
CANCEL/NO button
Used to return and cancel
Laser power adjustment
LDPWR CHECK
Laser power check
EF BAL ADJUST
Traverse adjustment
FBIAS ADJUST
Focus bias adjustment
FBIAS CHECK
Focus bias check
CPLAY MODE
Continuous playback mode
CREC MODE
Continuous recording mode
EEP MODE
Non-volatile storage memory control
Note : The numbers of “
“ADER”.
” displayed indicate the error rate and
2. Changing the playback location
1 Pressing the YES button during continuous playback will
change the display in the following manner, enabling change
in the playback location.
“CPLAY MID” n “CPLAY OUT” n “CPLAY IN”
↑
2 When accessing is completed, the display will change to “C1=
AD = ”.
Note : The numbers of “
“ADER”.
Functions
Used to change parameters and modes
Temperature compensation offset adjustment
LDPWR ADJUST
4-5-1. Operating in the Continuous Playback mode
1. Entering the Continuous Playback mode
1 Insert a disk into the unit (either recordable or playback disk)
2 Turn the AMS dial until “CPLAY MODE” is displayed.
3 Press the ENTER/YES button. The display will change to
“CPLAY IN”.
4 When accessing is completed, the display will change to “C1=
AD = ”.
All operations are made using the AMS dial, ENTER/YES button
and CANCEL/NO button.
The functions of each button are as follows:
AMS dial
TEMP ADJUST
” displayed indicate the error rate and
3. Exiting the Continuous Playback mode
1 Press the CANCEL/NO button. The display will change to
“CPLAY MODE”.
2 To remove the disk, press the MD EJECT button.
4-3. RELEASING THE TEST MODE
Function Name
Description
– 30 –
Note :
The playback initiate addresses of IN, MID and OUT are indicated below. To display the playback position, press the DISPLAY button and “CPLAY(
)”.
IN
40h cluster
MID
300h cluster
OUT
700h cluster
4-5-2. Operating in the Continuous Recording mode
1. Entering the Continuous Recording mode
1 Insert a disk that may be recorded into the unit (see Note 3)
2 Turn the AMS dial until “CREC MODE” is displayed.
3 Press the ENTER/YES button. The display will change to
“CREC MID”.
4 When accessing is completed, the display will change to
“CREC (
)”.
4-7. TEST MODE DISPLAY
The display will switch in the following sequence every time the
DISPLAY button is pressed.
Mode display
Error rate display
Note : The numbers of “ ” displayed indicate the record position address.
2. Changing the recording location
1 Pressing the YES button during continuous recording will
change the display in the following manner, enabling change
in the recording location. During location change, the REC
indicator will be off.
“CPLAY MID” n “CPLAY OUT” n “CPLAY IN”
↑
2 When accessing is completed, the display will change to
“CREC (
)” and the REC indicator will light.
Note : The numbers of “ ” displayed indicate the record position address.
3. Exiting the Continuous Recording mode
1 Press the CANCEL/NO button. The display will change to
“CREC MODE” and the REC indicator will turn off.
2 To remove the disk, press the MD EJECT button.
Note 1 : The record initiate addresses of IN, MID and OUT are indicated below.
IN
40h cluster
MID
300h cluster
OUT
700h cluster
Note 2 : The CANCEL/NO button can be used at anytime to stop recording.
Note 3 : Detection for the write-protect tab is not executed when in the
test mode. Do not enter the Continuous Recording mode with a
disk you do not wish to have deleted.
Note 4 : Do not continuously record for more than 5 minutes.
Note 5 : Make sure no vibration is applied to the unit during continuous
recording.
Address display
Auto-gain display (not used for servicing)
1. Mode display
Displays such information as “TEMP ADJUST” and “CPLAY
MODE”.
2. Error rate display
The error rate is displayed using the following format.
C1=C1ER AD=ADER
3. Address display
The address is displayed using the following format (MO : recordable disk, CD : playback disk)
Note : “–” is displayed when servo is off.
4. Auto-gain display (not used for servicing)
The auto-gain is displayed using the following format.
AG = @@/##[&&]
@@ : focus servo gain coefficient
## : tracking servo gain coefficient
&& : displays [OK], [NG] or [– –].
[– –] indicates that convergence is incomplete
Definitions of other displays
4-5-3. Non-volatile storage memory mode (EEP mode)
This is the mode to read and write the contents of the non-volatile
storage memory.
This is mode is not used for servicing.
If you accidently enter this mode, exit immediately by pressing the
CANCEL/NO button.
4-6. FUNCTIONS OF OTHER BUTTONS
Function Name
EDIT + ^
EDIT + p
)
0
EDIT + REC
EDIT + DELETE
EDIT + SHUF/PGM
DISPLAY
MD EJECT
RESET
Main Description
Continuous playback when pressed during
disk is stopped. Tracking servo ON/OFF
when pressed during continuous playback
Stopping of continuous recording/playback
The thread moves outward while the button is
pressed
The thread moves inward while the button is
pressed
Record ON/OFF during continuous playback
Switched between pit and groove every time
the button is pressed
Spindle servo mode switch
(CLV S N n CLV A)
Display contents are switched every time the
button is pressed
Eject disk
Exit the test mode
– 31 –
Display
ª
P
REC
AUTO
Description
Indicator ON
Indicator OFF
Continuous playback in
Disk stopped (CLV : OFF)
operation (CLV : ON)
Tracking servo OFF
Recording mode ON
ABCD adjustment
completed
DIGITAL
Focus auto-gain OK
TRACK
DISC
DATE
t
Pit
High reflection
CLV-S
CLV LOCK
Tracking servo ON
Recording mode OFF
(Flashing) Focus OK
Tracking auto-gain NG
Groove
Low reflection
CLV-A
CLV UNLOCK
SECTION 5
ADJUSTMENTS
MD SECTION
5-3. CAUTIONS DURING ADJUSTMENT
1) After replacing the following parts, make adjustments and checks
for the table items where indicated with a O in the order given.
5-1. CAUTION WHEN CHECKING LASER DIODE
EMISSION
Never look from directly above when checking the laser diode emission during adjustment as failure to do so may result in loss of eyesight.
5-2. CAUTIONS WHEN HANDLING THE OPTICAL
PICK-UP (KMS-260A)
The laser diode within the optical pick-up is extremely vulnerable
to static electricity. When handling, bridge the laser tap of the flexible board on the optical pick-up with solder.
When removing the connector, first bridge the laser tap with solder.
Furthermore, do not remove the soldered bridge before reconnecting. In addition, take sufficient measures when working to prevent
electrostatic damage. Take caution when handling the flexible board
since it is easily torn.
Pick-up
Flexible board
Optical
BD board
pickup IC171 D101 IC101,IC121,IC192
1. Temperature compensation offset adjustment
2. Laser power adjustment
3. Traverse adjustment
4. Focus bias adjustment
5. Error rate adjustment
X
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
O
O
O
O
2) Perform adjustments in the test mode.
Exit the test mode when completed with adjustment.
2) Perform adjustments in the order given.
3) Use the following jig and measuring equipment:
• Check disk (MD) TDYS-I (Part no : 4-963-646-01)
• Laser power meter LPM-8001 (Part no : J-2501-046-A)
• Oscilloscope (perform measurement after calibrating the
probe)
• Digital voltmeter
• Thermometer
• BD board waveform checking jig (part no : J-2501-124-A)
5) When looking at multiple signals using oscilloscope, etc., make
sure VC and GND are not connected within the oscilloscope.
Failure to do so will short circuit VC and GND.
6) Using the special jig enables checking of the waveform without
soldering (see page 4 of Service Notes).
Laser tap
5-4. CREATING A CONTINUOUS RECORDING
DISK
• This disk is used during focus bias adjustment and error rate
check. The procedure for creating a continuous recording disk
is as follows.
1. Insert a disk (any commercially available blank disk).
2. Turn the AMS dial until “CREC MODE” is displayed.
3. Press the YES button to display “CREC MID”.
“CREC(0300)” will be displayed for an instant and recording
will begin.
4. Complete recording within 5 minutes.
5. Press the NO button to stop recording.
6. Press the MD EJECT button to remove the disk.
A continuously recorded disk can be created by following the procedure above for focus bias adjustment and error rate check.
Note: Take caution as to not apply vibration to the unit during continuous recording.
– 32 –
5-5. TEMPERATURE COMPENSATION OFFSET
ADJUSTMENT
The temperature data at the time is saved in the non-volatile storage
memory as the standard data of 25°C.
Notes:
1. Do not make this adjustment under normal conditions.
2. Perform this adjustment in an environment with ambient temperature between 22 to 28°C. Furthermore, make the adjustment immediately after turning on the power when the internal
temperature and ambient temperature are between 22 to 28°C.
3. After D101 replacement, perform the adjustment after the part
has ample time to adjust to the ambient temperature.
Procedure:
1. Turn the AMS dial until “ TEMP ADJUST ” is displayed.
2. Press the ENTER/YES button and select the TEMP ADJUST
mode.
3. “ TEMP= ” and the current temperature data will be displayed.
4. To save the data: press the ENTER/YES button
To not save the data: press the CANCEL/NO button
5. After pressing the ENTER/YES button, “ TEMP= SAVE ”
will be displayed momentarily and the display will then return
to “ TEMP ADJUST ”.
The display will immediately return to “ TEMP ADJUST ” when
pressing the CANCEL/NO button.
Specified values:
The value of TEMP= must be within the range of E0-EF, F0-FF,
00-0F, 10-1F or 20-2F.
7. Next, turn the AMS dial until “ LDPWR CHECK ” is displayed.
8. Press the ENTER/YES button once to display “ LD 0.9mW $
”.
At this time, check to see that the laser power meter reading is
between 0.85 – 0.91mW.
9. Next, press the ENTER/YES button once more to display “ LD
”.
7.0mW $
At this time check to see that the laser power meter and digital
voltmeter reading comply with the specified values.
Specified values:
Laser power meter reading : 6.9–7.1mW
Digital voltmeter reading : ±10% the value on the label of the optical pickup.
(Optical pick-up label)
KMS 260A
27X40
B0825
In this case, Iop = 82.5mA
Iop(mA) = digital voltmeter reading (mV)/1(Ω)
10. Press the CANCEL/NO button to display “ LDPWR CHECK ”
and stop laser emission. (The CANCEL/NO button can be used
at anytime to stop laser emission.
5-7. TRAVERSE ADJUSTMENT
5-6. LASER POWER ADJUSTMENT
Connections:
Connection:
Laser power meter
Oscilloscope
BD board
CN110 3 pin (TEO)
CN110 2 pin (VC)
Optical pick-up
objective lens
V: 0.5V/div H: 10ms/div
Input: DC mode
Digital voltmeter
BD board
CN110 5 pin (I+3V)
CN110 4 pin (IOP)
Procedure:
1. Insert the laser power meter into the disk loading port and set
atop the objective lens of the optical pickup (if this cannot be
done successfully, shift the optical pickup using the 0 and
) buttons).
Connect the digital voltmeter to the CN110 5 pin (I+3V) and
CN110 4 pin (IOP).
2. Turn the AMS dial until “ LDPWR ADJUST ” is displayed.
(Laser power: adjustment purposes)
3. Press the ENTER/YES button once to display “ LD 0.9mW $
”.
4. Turn the AMS dial so that the laser power meter reading is between 0.86 – 0.92mW. After setting the range dial of the laser
power meter to 10mW, press the ENTER/YES button to save
the adjustment result to the non-volatile storage memory (at this
time, “ LD SAVE $
” will be displayed for an instant).
5. Next, “ LD 7.0mW $
” will be displayed.
6. Turn the AMS dial so that the laser power meter reading is between 6.9 – 7.1mW, then press the ENTER/YES button to save
the adjustment result (at this time, “ LD SAVE $
” will be
displayed for an instant).
Procedure:
1. Connect the oscilloscope to the CN110 3 pin (TEO) and CN110
2 pin (VC) of the BD board.
2. Insert a disk (any commercially available disk) that may be recorded on (see Note 1).
3. Press the 0 or ) button to shift the optical pick-up to the
outer edge of the pit.
4. Turn the AMS dial until “ EFBAL ADJUST ” is displayed.
5. Press the ENTER/YES button to display “ EFB= MO-R ”.
(The unit will be in the condition of: laser power READ power,
focus servo ON, tracking servo OFF and spindle (S) servo ON.)
6. Turn the AMS dial so that the waveform on the oscilloscope is
that of the specified value (turning the AMS dial will change the
numbers of “ EFB= ” as well as the waveform). During this
adjustment, the waveform changes for approximately every 2%.
Adjust the waveform closest to the specified value (read power
traverse adjustment).
(Traverse waveform)
A
VC
B
Specification: A=B
Note: Do not emit the 7.0mW emission more than 15 seconds continuously.
– 33 –
7. Press the ENTER/YES button to save the adjustment result to
the non-volatile storage memory (at this time “ EFB= SAVE
” will be displayed for an instant, then “ EFB= MO-W ” will
be displayed).
8. Turn the AMS dial so that the waveform on the oscilloscope is
that of the specified value (turning the AMS dial will change the
” as well as the waveform). During this
numbers of “ EFB=
adjustment, the waveform changes for approximately every 2%.
Adjust the waveform closest to the specified value (write power
traverse adjustment).
17. Press the ENTER/YES button to save the adjustment result to
the non-volatile storage memory (at this time “EFB= SAVE”
will be displayed for an instant). “EFBAL ADJUST” will then
be displayed.
18. Press the MD EJECT button to remove the check disk (MD)
TDYS-1.
Note 1: When using a pre-recorded disk for adjustment, data will be
deleted during MO write.
Note 2: If the traverse waveform is hard to see, reconnect the oscilloscope as shown below for easier view.
(Traverse waveform)
Oscilloscope
A
BD board
VC
CN110 3 pin (TEO)
CN110 2 pin (VC)
B
330kΩ
10pF
Specification: A=B
9. Press the ENTER/YES button to save the adjustment result to
the non-volatile storage memory (at this time “ EFB= SAVE
” will be displayed for an instant).
10 “ EFB= MO-P ” will then be displayed and the servo will be
activated after the optical pickup is automatically shifted to the
inner edge of the pit.
11. At this time, turn the AMS dial so that the waveform on the
oscilloscope is that of the specified value. During this adjustment, the waveform changes for approximately every 2%. Adjust the waveform closest to the specified value.
and the rotation of the disk will automatically stop.
(Traverse waveform)
A
VC
B
Specification: A=B
12. Press the ENTER/YES button to save the adjustment result to
the non-volatile storage memory (at this time “ EFB= SAVE
” will be displayed for an instant). “EFBAL CD” will then be
displayed
13. Press the MD EJECT button to remove the disk.
14. Insert the check disk (MD) TDYS-1.
15. Press the ENTER/YES button to display “ EFB= CD ”. The
servo will automatically be activated.
16. Turn the AMS dial so that the waveform on the oscilloscope is
that of the specified value. During this adjustment, the waveform changes for approximately every 2%. Adjust the waveform closest to the specified value.
(Traverse waveform)
5-8. FOCUS BIAS ADJUSTMENT
Procedure:
1 Insert a continuously recorded disk (see 5-4. Creating a continuous recording disk).
2. Turn the AMS dial until “CPLAY MODE” is displayed.
3. Press the ENTER/YES button to display “CPLAY MID”.
AD=
” is displayed, press the CANCEL/
4. When “C1=
NO button.
5. Turn the AMS dial until “FBIAS ADJUST” is displayed.
6. Press the ENTER/YES button to display “
/ a= ”.
The first 4 digits indicate the C1 error rate, the 2 digits following “/” indicate ADER and the 2 digits following “a=” indicate
the focus bias volume.
7. Turn the AMS dial clockwise and search the focus bias volume
closest to the C1 error rate of 220 (see Note 2).
/ b=
”.
8. Press the ENTER/YES button to display “
9. Turn the AMS dial counterclockwise and search the focus bias
volume which is the C1 error rate of 220.
/ c= ”.
10. Press the ENTER/YES button to display “
11. Press the ENTER/YES button after making sure that the C1 error rate is below 50 and ADER is 00.
12. Press the ENTER/YES button if the value indicated in the “
- - (
)” display is more than 20.
Otherwise, press the CANCEL/NO button and repeat procedure
from step 2.
13.Press the MD EJECT button to remove the continuously recorded
disk.
Note 1: The relationship of the C1 error and focus bias volume is shown
in the diagram below. Find points a and b shown in the diagram
by following the procedure above. The met focal point C is
found by automatic calculation.
Note 2: The C1 error rate fluctuates. Thus, make the adjustment using
the average value.
C1 error
A
VC
220
B
Specification: A=B
Focus bias volume
(F, BIAS)
b
– 34 –
c
a
5-9. ERROR RATE CHECK
5-11. ADJUSTMENT AND CONNECTION LOCATIONS
5-9-1. CD error rate check
Procedure:
1. Insert the check disk (MD) TDYS-1
2. Turn the AMS dial until “ CPLAY MODE ” is displayed.
3. Press the ENTER/YES button to display “ CPLAY MID ”.
4. The display will change to “ C1=
AD= ”.
5. Check to see that the C1 error rate is less than 20.
6. Press the CANCEL/NO button to stop playback, then press the
MD EJECT button to remove the check disk (MD).
[BD BOARD] (Side A)
5
1
RF
VC
5-9-2. MO error rate check
Procedure:
1. Insert a continuously recorded disk (see 5-4. Creating a continuous recording disk).
2. Turn the AMS dial until “ CPLAY MODE ” is displayed.
3. Press the ENTER/YES button to display “ CPLAY MID ”.
AD= ”.
4. The display will change to “ C1=
5. Check to see that the C1 error rate is less than 50 and ADER is
constantly not above 00.
6. Press the CANCEL/NO button to stop playback, then press the
button to remove the continuously recorded disk.
TEO
CN110
I+3V
IOP
Note
CN101
D101
5-10. FOCUS BIAS CHECK
The focus tolerance volume is checked by changing the focus bias
volume.
Procedure:
1. Insert a continuously recorded disk (see 5-4. Creating a continuous recording disk).
2. Turn the AMS dial until “CPLAY MODE” is displayed.
3. Press the ENTER/YES button to display “CPLAY MID”.
4. When “C1=
AD=
” is displayed, press the CANCEL/
NO button.
5. Turn the AMS dial until “FBIAS CHECK” is displayed.
/ c= ”.
6. Press the ENTER/YES button to display “
The first 4 digits indicate the C1 error, the 2 digits following “ /
” indicate ADER and the 2 digits following “c=” indicate the
focus bias volume.
At this time, check to see that the C1 error is less than 50 and
ADER is 00.
/
7. Press the ENTER/YES button to change the display to “
b=
”
At this time check to see that the C1 error is not less than 220
and ADER is constantly not above 00.
8. Press the ENTER/YES button to change the display to “
/
a= ”
At this time check to see that the C1 error is not less than 220
and ADER is constantly not above 00.
9. Press the CANCEL/NO button, then press the MD EJECT button to remove the continuously recorded disk.
IC192
[BD BOARD] (Side B)
IC121
IC101
IC171
Note 1: If the C1 error or ADER is more than 00 for only one of points
a (8. above) and b (7. above), there is the possibility of a gap in
the focus bias adjustment. In such case, repeat adjustment.
Note: The jig is highly convenient when checking the waveform
(see page 4 of Service Notes)
– 35 –
CD SECTION
3. Traverse signal check
Connection Point:
1. Enter the CD Test mode
(see page 30)
Oscilloscope
Main board
MD EF TG FB
88 07 00 3A0
CN701 $∞ pin (TEO)
TP(VC)
Press the FF or FR from 2.
Check to see that the traverse signal level is between 400
600mVp-p.
The above is the default display.
Pressing the ^ key will rotate the CD and pressing the ^
once more will output sounds.
Pressing the ^ key will execute automatic adjustment and
values will change; however, this value is quite normal.
2. RF LEVEL and jitter check
Test mode PLAY status
Connection Point:
Note:
Extend the sweep time
for easier view.
A
400 – 600mVp-p
0V
B
Oscilloscope
A
0V
B
A=B
Main board
TP(RFO)
TP(VC)
4. After completed with adjustment, press the RESET button to
release the test mode.
Check to see that the jitter is less than 9.0 nsec.
and RF level is between 1.1 – 1.5Vp-p.
Adjustment Location :
VOLT/DIV : 200mV (using 10:1 probe)
TIME/DIV : 500ns
[MAIN BOARD] (SIDE A)
IC701 $∞ pin
(TEO)
RF level:
1.1 - 1.5Vp-p
– 36 –
TP
(RFO)
TP
(VC)
TUNER SECTION
EXCEPT US model
AM Section
Function switch :
AM
: US Model
MW (LW) : EXCEPT US Model
Volume : MIN
AM RF signal
generator
FM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
L10
10.7MHz
LW FREQUENCY COVERAGE ADJUSTMENT
reading on digital
Adjust part
Frequency display
voltmeter
Confirmation
153kHz
0.6 – 0.8V
CT4
297kHz
5.1 – 5.5V
Put the lead-wire
antenna close to
the set.
30% amplitude modulation by 400Hz
signal.
Output level : as low as possible
LW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L5
CT5
FM Section
Function switch : FM
Volume : MIN
162kHz
261kHz
[TUNER BOARD] (SIDE B)
FM RF signal
generator
US Model
0.01 µF
Digital
voltmeter
telescopic
antenna
terminal
100 k Ω
TP (VT)
22.5kHz frequency deviation by
400Hz signal.
Output level : as low as possible
+
–
level meter
32 Ω
+
–
set
VT
J301 (phones)
Connect and Adjustment Location : Tuner board (See page 38)
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
<
> : EXCEPT US model
EXCEPT US Model
Digital
voltmeter
AM <MW/LW> IF ADJUSTMENT
Adjust for a maximum reading on level meter.
CFT1
100 k Ω
450kHz
AM <MW> FREQUENCY COVERAGE ADJUSTMENT
reading on digital
Adjust part
Frequency display
voltmeter.
L2
530kHz
0.9 – 1.1V
< L4 >
< 531kHz >
< 0.8 – 1.0V >
Confirmation
1.710kHz
5.2 – 5.6V
< CT2 >
< 1.611kHz >
< 5.2 – 5.6V >
VT
AM <MW> TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
CT1
< CT3 >
L1
< L3 >
620kHz
< 621kHz >
1.400kHz
< 1.404kHz >
– 37 –
TP (VT)
+
–
Adjustment Location :
US Model
[TUNER BOARD] (Side A)
CFT1 : AM IF Adjustment
IC 1
L1 : AM Tracking Adjustment
L2 : AM Frequency Coverage Adjustment
CT1 : AM Tracking Adjustment
EXCEPT US Model
[TUNER BOARD] (Side A)
CFT1 : MW (LW) IF Adjustment
L10 : FM IF Adjustment
IC 1
L5 : LW Tracking Adjustment
L3 : MW Tracking Adjustment
CT3 : MW Tracking Adjustment
CT5 : LW Tracking Adjustment
CT4 : LW Frequency Adjustment
L4 : MW Frequency Coverage Adjustment
CT2 : MW Frequency Coverage Adjustment
– 38 –
SECTION 6
DIAGRAMS
6-1. EXPLANATION OF IC TERMINALS
BD BOARD IC101 MD SECTION RF AMPLIFIER (CXA2523R)
Pin No.
Pin name
I/O
1
I
I
Description
Input of RF signal l converted from I to V
2
J
I
Input of RF signal J converted from I to V.
3
VC
O
Midpoint voltage (+1.5V) generation output.
4-9
A–F
I
Signal inputs from optical pickup detector.
10
PD
I
Light volume monitor input.
11
APC
O
Laser APC output.
12
APCREF
I
Reference voltage input for laser power setting.
13
GND
–
Ground.
14
TEMPI
I
Temperature sensor connection terminal.
15
TEMPR
O
Reference voltage output for temperature sensor.
16
SWDT
I
Serial data input from CXD2652AR.
17
SCLK
I
Serial clock input from CXD2652AR.
18
XLAT
I
Latch signal input from CXD2652AR. “L”: Latch
19
XSTBY
I
Standby signal input. “L”: Standby
20
FOCNT
I
21
VREF
O
22
EQADJ
I/O
Pin for center frequency setting of internal circuit EQ.
23
3TADJ
I/O
Pin for center frequency setting of internal circuit BPF3T.
Center frequency control voltage input of internal circuits BFF22, BPF3T and EQ from
CXD2652AR.
Reference voltage output (not used).
24
VCC
–
25
WBLADJ
I/O
Power supply (+3V).
26
TE
O
Tracking error signal output to CXD2652AR.
27
CSLED
–
External condenser connector pin for thread error signal LPF.
Pin for center frequency setting of internal circuit BPF22.
28
SE
O
Thread error signal output to CXD2652AR.
29
ADFM
O
ADIP FM signal output.
30
ADIN
I
ADIP signal comparator input ADFM connection by coupling with AC.
31
ADAGC
–
External condenser connector pin for AGC of ADIP.
32
ADFG
O
ADIP duplex signal output to CXD2652AR.
33
AUX
O
I3 signal/temperature signal output (switched by serial command) to CXD2652AR.
34
FE
O
Focus error signal output to CXD2652AR.
35
ABCD
O
Light volume signal output to CXD2652AR.
36
BOTM
O
RF/ABCD bottom hold signal output to CXD2652AR.
37
PEAK
O
RF/ABCD peak hold signal output to CXD2652AR.
38
RF
O
RF equalizer output to CXD2652AR.
39
RFAGC
–
RF AGC circuit external condenser connector pin.
40
AGCI
I
Input RF amplifier output is input to RF AGC circuit by coupling with AC.
41
COMPO
O
User comparator output (not used).
42
COMPP
I
43
ADDC
I/O
44
OPO
O
User op amplifier output (not used).
45
OPN
I
User op amplefier inverted input (Fixed at “L”).
46
RFO
O
RF amplifier output.
47
MORFI
I
Group RF signal input by coupling with AC.
48
MORFO
O
Group RF signal output.
User comparator input (Fixed at “L”).
Low-pass cutoff external capacitor terminal of ADIP amplifier.
APC : Auto Power Control
AGC : Auto Gain Control
– 39 –
• BD BOARD IC121 digital signal processor, digital servo signal processor, EFM/ACIRC encoder/decoder, shockproof memory controller, ATRAC encoder/decoder, 2Mbit DRAM (CXD2652AR)
Pin No.
Pin name
I/O
Description
1
MNT0(FOK)
O
2
MNT1(SHCK)
O
3
MNT2(XBUSY)
O
Monitor 2 output to system control.
4
MNT3(SLOC)
O
Monitor 3 output to system control.
5
SWDT
I
Write-data signal input from system control.
6
SCLK
I(S)
Serial clock signal input from system control.
7
XLAT
I(S)
Serial latch signal input from system control.
8
SRDT
O(3)
Read-data signal output to system control .
FOK signal output to system control.
H is outputted when in focus.
Track-jump detection signal output to system control.
9
SENS
O(3)
Internal status (SENSE) output to system control.
10
XRST
I(S)
Reset signal input from system control. “L”: Reset
11
SQSY
O
12
DQSY
O
13
RECP
I
Laser power switch input from system control “H”: Record, “L”: Playback.
14
XINT
O
Interrupt status output to system control.
15
TX
I
Record data output authorization input from system control.
Subcode Q-SYNC (SCOR) output to system control.
Majority of those which output “L” every 13.3 seconds output “H”.
Subcode of digital-in U-bit CD format to system control.
Majority of those which outputs “L” every 13.3 seconds during output of Q-SYNG
(SCOR) outputs “H”.
16
OSCI
I
System clock input (512Fs = 22.5792MHz).
17
OSCO
O
System clock output (512FS = 22.5792MHz).
18
XTSL
I
19
TEST G
–
Test terminal.
20
DVSS
–
Ground (digital system).
Pin for system clock frequency setting .
“L”: 45.1584MHz “H”: 22.5792MHz (Fixed at “H”).
21
DIN
I
Digital audio input (for optical input).
22
DOUT
O
Digital audio output (for optical output).
23
ADDT
I
Data input from A/D converter.
24
DADT
O
Data output to D/A converter.
25
LRCK
O
LR clock output (44.1kHz) for A/D and D/A converters.
26
XBCK
O
Bit clock output (2.8224MHz) for A/D and D/A converters.
27
FS256
O
11.2896MHz clock output (unused).
28
DVDD
–
Power supply for digital (+3V).
29–32
A03–A00
O
33
A10
O
34–38
A04–A08
O
39
A11
O
40
DVSS
–
Ground for digital.
41
XOE
O
DRAM output-enable output.
42
XCAS
O
DRAM CAS signal output.
43
A09
O
DRAM address output.
44
XRAS
O
DRAM RAS signal output.
45
XWE
O
DRAM write-enable signal output.
46
D1
I/O
47
D0
I/O
48, 49
D2,D3
I/O
50
MVCI
I(S)
DRAM address outputs.
DRAM data I/O.
Clock input from external VCO (Fixed at “L”).
* In the I/O column, I(S) is Schmitt input, I(A) is analog input, O(3) is state output and O(A) is analog output.
– 40 –
Pin No.
Pin name
I/O
Description
51
ASYO
O
52
ASYI
I(A)
53
AVDD
–
54
BIAS
I(A)
Playback EFM comparator bias current input.
55
RFI
I(A)
Playback EFM RF signal input.
56
AVSS
–
57
PDO
O(3)
Phase comparison output for clock playback analog PLL of playback EFM (not used).
58
PCO
O(3)
Phase comparison output for record/playback EFM system master PLL.
Playback EFM duplex signal output.
Playback EFM comparator slice level input.
Power supply for analog (+3V).
Ground for analog.
59
FILI
I(A)
Filter input for record/playback EFM system master PLL.
60
FILO
O(A)
Filter output for record/playback EFM system master PLL.
61
CLTV
I(A)
Internal VCO control voltage input for record/playback EFM system master PLL15.
62
PEAK
I(A)
Light volume signal peak hold input from CXA2523AR.
63
BOTM
I(A)
Light volume signal bottom hold input from CXA2523AR.
64
ABCD
I(A)
Light volume signal input from CXA2523AR.
65
FE
I(A)
Focus error signal input from CXA2523AR.
66
AUX1
I(A)
Auxiliary A/D input.
67
VC
I(A)
Midpoint voltage (+1.5V) input from CXA2523AR.
68
ADIO
O(A)
A/D converter input signal monitor output (not used).
69
AVDD
–
70
ADRT
I(A)
A/D converter operating range upper limit voltage input (Fixed at “H”) .
71
ADRB
I(A)
A/D converter operating range lower limit voltage input (Fixed at “L”).
72
AVSS
–
Power supply for analog (+3V).
Ground for analog.
73
SE
I(A)
Thread error signal input from CXA2523AR.
74
TE
I(A)
Tracking error signal input from CXA2523AR.
75
AUX2
I(A)
Auxiliary A/D input (Fixed at “L”).
76
DCHG
I(A)
Connected to +3V power supply.
77
APC
I(A)
Laser digital APC error signal input (Fixed at “L”).
78
ADFG
I(S)
ADIP duplex FM signal input (22.05±1kHz) from CXA2523AR.
79
F0CNT
O
Filter f0 control output from CXA2523AR.
80
XLRF
O
Control latch output from CXA2523AR.
81
CKRF
O
Control clock output from CXA2523AR.
82
DTRF
O
Control data output from CXA2523AR.
83
APCREF
O
Laser APC reference PWM output.
84
LDDR
O
Laser digital APC PWM output (not used).
85
TRDR
O
Tracking servo drive PWM output (-).
86
TFDR
O
Tracking servo drive PWM output (+).
87
DVDD
–
Power supply for digital (+3V).
88
FFDR
O
Focus servo drive PWM output (+).
89
FRDR
O
Focus servo drive PWM output (-).
90
FS4
O
176.4kHz clock signal output (X’tal) (not used).
91
SRDR
O
Thread servo drive PWM output (-).
92
SFDR
O
Thread servo drive PWM output (+).
93
SPRD
O
Spindle servo drive PWM output (-).
94
SPFD
O
Spindle servo drive PWM output (+).
95
FGIN
I(S)
Spindle CAV servo FG input.
96–98
TEST1–TEST3
I
Test input pins (Fixed at “L”).
99
DVSS
–
Ground for digital.
100
EFMO
O
EFM output during recording.
EFM : Eight to Fourteen Modulation
PLL : Phase Locked Loop
VCO : Voltage Controlled Oscillator
– 41 –
DG BOARD (2/2) IC502 SYSYTEM CONTROL (RU8X12MF-0021)
Pin No.
Pin name
I/O
1
DAOUT0
–
2
DAOUOT1
–
not used (OPEN).
3
KEY0
–
Reserved (“H” level).
4
KEY1
–
Reserved (“H” level).
5
KEY2
–
Reserved (“H” level).
6
CHACK IN
I
Detection input from chucking-in switch (S685).
7
PACK IN
I
Detection input from back-in switch (not used).
8
PACK OUT
9
10
11
AVSS
Description
not used (OPEN).
I
Detection input from back-out switch (S686).
–
not used (ground connection).
–
not used (ground connection).
–
ground for analog.
12
X INT
I
Interrupt status input from digital signal processor IC (IC121).
13
PDOWN
I
Power cutoff signal input from master control IC (IC801).
–
Reserved (ground connection).
I
Subcode Q-SYNC (SCOR) input from digital signal processor IC (IC121).
14
15
SQSY
16
DQSY
I
Digital-in U-bit format subcode input from digital signal processor IC (IC121).
17
–
Reserved (ground connection).
18
–
Reserved (ground connection).
19
–
Reserved (ground connection).
20
________
SYS-RST
I
System reset input pin “L”: Reset.
21
TEST
I
Test mode pin “L”: Normal mode, “H”: Test mode.
22
+3.3V
–
Power supply terminal (VCC).
23
VBAT
I
Power supply pin for internal RTC and RAM.
24
XOUT-T
O
Sub-clock connector pin (32.768kHz).
25
XINT-T
I
Sub-clock connector pin (32.768kHz).
26
GND
–
Power supply terminal (ground).
27
XOUT
O
Main clock connector pin (12MHz).
28
XIN
I
Main clock connector pin (12MHz).
29
EXEM
I
Switch pin for External ROM mode and Internal ROM mode.
30
S1
–
not used (OPEN).
–
Reserved (ground connection).
31
32
SENS
I
Internal status (SENSE) input from digital signal processor IC (IC121).
33
SHOCK
I
Track-jump detection signal input from digital signal processor IC (IC121).
34
–
Reserved (ground connection).
35
–
Reserved (ground connection).
36
STB
O
Power ON/OFF control signal output.
37
REC P
I
Detection input from REC switch (S688).
38
PB P
I
Detection input from PB switch (S687).
39
LD LOW
O
Loading motor control signal output.
40
NC
–
not used (OPEN).
41
MNT2
I
Monitor 2 input from digital signal processor IC (IC121).
42
MNT3
I
Monitor 3 input from digital signal processor IC (IC121).
43
LEDO
–
not used (OPEN).
44
–
Reserved (ground connection).
45
–
Reserved (ground connection).
46
RST LOW
–
not used (OPEN).
47
GND
–
Power supply terminal (ground).
48
+3.3V
–
Power supply terminal (VCC).
49
SNG/CHG
–
Reserved (ground connection).
50
JOG1
–
Reserved (ground connection).
– 42 –
MAIN BOARD (2/2) IC801 SYSYTEM CONTROL (CXP84648-037Q)
Pin No.
Pin name
I/O
51
JOG0
–
Description
Pin No.
Pin name
I/O
Description
Pin No.
Pin name
I/O
FLSCK1
O
Reserved (ground connection).
1
PACON
O
Power amplifier control output.
51
MEGABASE
O
Mega-bus control output.
Description
Communication with FL microcomputer and clock output.
52
SDA
I/O
Serial data I/O with EEPROM (IC171).
2
52
FLCS1
O
FL microcomputer chip select output.
53
SCL
O
Serial clock output to EEPROM (IC171).
3
RECH
O
A/D converter select output.
53
FLDT1
O
Communication with FL microcomputer and data output.
54
2M/4M
–
Reserved (“H” level).
4
STXD
O
Communication with MD and UART send output.
54
JOG1
I
JOG dial rotation detection 1 input.
–
Reserved (ground connection).
5
SRXD
I
Communication with MD and UART receive input.
55
JOG2
I
JOG dial rotation detection 2 input.
SCTS
I
UART send request input from MD.
55
–
Reserved (ground connection).
6
56
RMC
I
remote control signal input.
57
RXD (UART)
O
Communication with master control IC (IC801) and UART receive output.
7
SRTS
O
UART send request output to MD.
57
RDI
I
Radio PLL data input.
58
TXD (UART)
I
Communication with master control IC (IC801) and UART send input.
8
MDH
O
D/A converter select output.
58
RDO
O
Radio PLL data output.
59
RTS (T)
I
UART send request input from master control IC (IC801).
9
PDOWN
O
Notification of power cutoff to MD.
59
RSCK
O
Radio PLL clock output.
MDRST
O
Reset MD microcomputer.
56
60
CTS (R)
O
UART send request output to master control IC (IC801).
10
60
RCE
O
Radio PLL chip enable output.
61
AUBIT0
–
Reserved (“H” level).
11
PCON
O
Power supply control output.
61
SCOR
I
CD score input.
62
AUBIT1
–
Reserved (ground connection).
12
OPEN
O
CD tray control output H: Open.
62
FOK
I
CDFOK input.
63
CLKSET0
–
Reserved (ground connection).
13
CLOSE
O
CD tray control output H: Close.
63
–
not used (OPEN).
XRST
O
CD system reset output.
64
CLKSET1
–
Reserved (ground connection).
14
64
EPSD
I/O
65
GND
–
Power supply pin (ground).
15
MDATA
O
CD serial data output.
65
SQCK
O
CDSUBQ clock output.
SENSE1
I
CD sense input 1.
EEPROM data I/O.
66
+3.3V
–
power supply pin (VCC).
16
66
SUBQ
I
CDSUBQ data input.
67
SCLK
O
Serial clock output to digital signal processor IC (IC201).
17
MCLK
O
CD serial clock output.
67
EPSK
O
EEPROM clock output.
XLT
O
CD system latch output.
68
ST
I
Radio stereo detection. “L”: Mono
–
not used.
69
9/10
I
Radio AM station interval switch. “L”: Set to 9kHz
68
SWDT
O
Write data signal output to digital signal processor IC (IC121).
18
69
SRDT
I
Read data signal input from digital signal processor IC (IC121).
19
SENCE2
I
CD sense input 1.
70
EMP
O
Delmphasis ON/OFF control signal output.
20
70
RMUTE
O
Radio mute output.
71
SCK1
–
not used (OPEN).
21
TEST
I
Test mode input. “L”: Reset
71
EPCS
O
EEPROM chip select output.
RSMK1
I
Radio-directed setting 1 (+5V connection).
72
SOUT1
–
not used (OPEN).
22
72
VDD
–
Power supply terminal (+5V).
73
SIN1
–
not used (OPEN).
23
RSMK2
I
Radio-directed setting 2 (ground connection).
73
NC
–
VDD connection.
RSMK3
I
Radio-directed setting 3 (ground connection).
74
CSB
–
Reserved (VCC connection).
24
74
MD
–
not used (OPEN).
75
LDON
O
Laser ON/OFF control signal output.
25
ACCHK
I
AC power supply detection input. L: AC H: No AC
75
CD
O
CD function output.
76
PIT/GRV
–
not used (OPEN).
26
LEDMD
O
LED on during MD.
76
RADIO
O
Radio function output.
77
FOK
I
Focus OK signal input from digital signal processor IC (IC121).
27
LEDCD
O
LED on during CD.
77
XLINE
O
Line function output.
–
not used (OPEN).
28
LEDRADIO
O
LED on during radio.
78
VOCLK
O
Serial data output for volume.
–
not used (OPEN).
29
SHIFT
O
Shift system clock.
79
AMUTE
O
Audio mute output.
RST
I
Hardware reset pin. “L”: Reset
80
VOLDATA
O
Serial clock output for volume.
78
79
80
81
82
83
LOCK
WRPWR
________
DIG-RST
_______
DA-RST
O
Laser power switch signal output to digital signal processor IC (IC121).
30
O
Reset signal output.
31
EXTAL
I
System clock (5MHz) oscillation input.
–
not used (OPEN).
32
XTAL
O
System clock (5MHz) oscillation output.
O
Reset signal output to D/A and A/D converters “L”: reset.
33
VSS
TX
O
Time clock (32.768kHz) oscillation output.
I
Ground.
84
DSEL-A
–
not used (OPEN).
34
85
DSEL-B
–
not used (OPEN).
35
TEX
O
MD module ON/OFF control signal output.
36
AVSS
–
not used (OPEN).
37
AVREF
I
A/D converter reference voltage input.
–
not used (OPEN).
38
KEY1
I
Key input (12 stage input) 1.
O
Record data output authorization signal output.
39
KEY2
I
Key input (12 stage input) 2.
O
Serial latch signal output to digital signal processor IC (IC121).
40
KEY3
I
Key input (12 stage input) 3.
–
not used (OPEN).
41
–
not used (OPEN).
–
not used (OPEN).
42
–
not used (OPEN).
–
not used (OPEN).
43
–
not used (OPEN).
REGCHK
I
Regulator voltage check input.
86
87
MOD
__
REC/PB
88
89
90
SCTX
XLATCH
91
92
93
AMUTE
Time clock (32.768kHz) oscillation input.
Ground for A/D converter.
94
LD OUT
O
Loading motor F control signal output.
44
95
LD IN
O
Loading motor F control signal output.
45
OPN/CLS
I
CD tray status detection input.
FLRST
O
FL microcomputer reset.
96
LIMIT IN
I
Detection input from limit switch (S681).
46
97
PROTECT
I
Record tab detection input from disk write-protect switch (S683).
47
FLCS2
O
FL name communication and chip select output.
FLSCK2
O
FL name communication and clock output.
98
REFLECT
I
Disk reflection rate detection input from reflect switch (S682).
48
99
GND
–
Power supply terminal (ground).
49
FLDI2
I
FL name communication and data input.
Power supply terminal (VCC).
50
FLDO2
O
FL name communication and data output.
100
+3.3V
–
– 43 –
– 44 –
– 45 –
ZS-M7
6-2. BLOCK DIAGRAM (1)
• Signal path.
F : FM
E : MD PLAY
q : MD REC
J : CD
– 46 –
– 47 –
– 48 –
ZS-M7
6-3. BLOCK DIAGRAM (2)
r
Circuit Boards Location
LEFT KEY board
FRONT KEY board
FILTER board
TOP KEY board
RIGHT KEY board
FM ANT board
TRANS board
AM ANT board
TUNER board
PICK-UP RELAY board
RELAY board
FL board
SW board
BD board
LINE IN board
AUDIO board
MAIN board
HP board
• Signal path.
F : FM
E : MD PLAY
q : MD REC
J : CD
– 49 –
– 50 –
– 51 –
– 52 –
LOADING board
DG board
– 53 –
6-5. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) –
r
Refer to page 103 for IC Block Diagrams.
ZS-M7
r Waveforms
1
– Main Section (1/2) –
4
PLAY MODE
2.2 Vp-p
1.1 – 1.5 Vp-p
8.7 µsec
IC701 #£ (RFO)
IC703 @ª (PCO)
VOLT/DIV : 200 mV AC
TIME/DIV : 0.5 µsec
2
PLAY MODE
VOLT/DIV : 0.5 V AC
TIME/DIV : 2 µsec
5
5.1 Vp-p
0.6 Vp-p
23.25 µsec
IC701 6 (FEO)
IC703 $º (LRCKI)
VOLT/DIV : 0.2 V AC
TIME/DIV : 0.2 msec
3
PLAY MODE
VOLT/DIV : 1 V AC
TIME/DIV : 5 µsec
6
PLAY MODE
2.2 Vp-p
0.7 Vp-p
16.44 MHz
IC701 $∞ (TEO)
IC703 &¡ (XTAO)
VOLT/DIV : 0.2 V AC
TIME/DIV : 0.5 msec
VOLT/DIV : 0.5 V AC
TIME/DIV : 20 nsec
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
%
: indicates tolerance.
Note: The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD (STOP)
(
) : CD (PLAY)
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD
– 59 –
– 60 –
– 61 –
– 62 –
6-6. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) –
ZS-M7
r Waveforms
– Main Section (2/2) –
1
2 Vp-p
5 MHz
IC801 #™ XTAL
VOLT/DIV : 0.5 V AC
TIME/DIV : 50 nsec
2
5.2 Vp-p
32 kHz
IC801 #¢ TX
VOLT/DIV : 1 V AC
TIME/DIV : 10 µsec
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
%
: indicates tolerance.
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD (STOP)
(
) : CD (PLAY)
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
E : MD PLAY
q : MD REC
J : CD
– 63 –
– 64 –
– 65 –
– 66 –
6-7. PRINTED WIRING BOARDS – TUNER SECTION (US MODEL) –
r
r
Refer to page 53 for Circuit Boards Location.
6-8. SCHEMATIC DIAGRAM – TUNER SECTION (US MODEL) –
r
ZS-M7
Refer to page 102 for IC Block Diagrams.
Semiconductor
Location
Ref. No.
Location
D1
D2
D3
D4
D5
G-2
G-2
G-1
G-1
H-3
D6
G-6
IC1
IC2
G-4
F-8
Q1
Q2
Q3
Q4
Q5
E-5
F-5
H-9
G-9
G-5
Q6
Q7
Q8
H-6
H-8
G-8
Note:
• X : parts extracted from the component side.
• b : Pattern on the side which is seen.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
– 67 –
– 68 –
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
– 69 –
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
¢
•
: internal component.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : AM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
– 70 –
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
r Waveform
– Tuner Section –
1
1.0 Vp-p
75 kHz
IC2 1
VOLT/DIV : 0.2 V AC
TIME/DIV : 5 µsec
– 71 –
ZS-M7
r
6-9. PRINTED WIRING BOARDS – TUNER SECTION (EXCEPT US MODEL) –
6-10. SCHEMATIC DIAGRAM – TUNER SECTION (EXCEPT US MODEL) –
r
Refer to page 102 for IC Block Diagrams.
Semiconductor
Location
Ref. No.
Location
D3
D4
D5
D10
D40
H-3
G-1
G-1
G-6
G-2
D41
D50
D51
G-2
F-3
F-3
IC1
IC2
G-4
F-8
Q1
Q3
Q4
Q5
Q6
G-8
G-9
H-9
H-8
H-6
Q7
Q8
Q50
Q51
Q52
E-5
G-5
F-5
H-8
H-4
Q53
Q54
Q57
H-3
G-2
H-3
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
¢
•
: internal component.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : AM
<
> : LW
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Note:
• X : parts extracted from the component side.
• b : Pattern on the side which is seen.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
– 72 –
– 73 –
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
– 74 –
– 75 –
r Waveform
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
– Tuner Section –
1
1.0 Vp-p
75 kHz
IC2 1
VOLT/DIV : 0.2 V AC
TIME/DIV : 5 µsec
– 76 –
6-11. SCHEMATIC DIAGRAM – BD SECTION –
r
Refer to page 100 for IC Block Diagrams.
-12. PRINTED WIRING BOARDS – BD SECTION –
r
r
ZS-M7
Refer to page 53 for Circuit Boards Location.
Waveforms – BD Section –
1
PLAY MODE
PLAY MODE
2
1.3 Vp-p
0.46 Vp-p
IC101 1, 2 I, J
IC101 #• RF
VOLT/DIV : 0.2 V AC
TIME/DIV : 0.5 µsec
4
0.1 Vp-p
IC101 4 A
VOLT/DIV : 20 mV AC
TIME/DIV : 1 µsec
VOLT/DIV : 0.5 V AC
TIME/DIV : 0.5 µsec
5
PLAY MODE
PLAY MODE
3
6
3.4 Vp-p
1.0 Vp-p
60 mVp-p
22.581 MHz
IC101 8, 9 E, F
23.05 µsec
IC121 !¶ OSCO
7
IC121 @∞ LRCK
VOLT/DIV : 0.2 V AC
TIME/DIV : 50 nsec
VOLT/DIV : 20 mV AC
TIME/DIV : 1 µsec
8
9
3.2 Vp-p
2.2 Vp-p
3.5 Vp-p
0.36 µsec
5.6 µsec
90 nsec
IC121 @§ XBCK
VOLT/DIV : 1 V AC
TIME/DIV : 10 µsec
IC121 @¶ FS256
VOLT/DIV : 1 V AC
TIME/DIV : 0.1 µsec
IC121 (º FS4
VOLT/DIV : 0.5 V AC
TIME/DIV : 50 nsec
VOLT/DIV : 1 V AC
TIME/DIV : 2 µsec
r
Semiconductor
Location
Ref. No.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
%
: indicates tolerance.
Note: The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD STOP
(
) : MD PLAY
<
> : MD REC
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
– 77 –
– 78 –
– 79 –
Location
D101
D181
D183
E-4
C-9
C-9
IC101
IC103
IC121
IC122
IC123
E-13
B-13
D-11
C-5
D-10
IC124
IC152
IC171
IC181
IC192
E-11
B-11
E-9
D-9
F-7
Q101
Q102
Q103
Q104
Q162
C-13
B-14
B-13
C-13
B-13
Q163
Q180
Q181
Q182
B-14
D-7
C-9
C-9
Note:
• X : parts extracted from the component side.
• b : Pattern on the side which is seen.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side:
Parts on the parts face side seen from the
(Side A)
parts face are indicated.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E : MD PLAY
q : MD REC
J : CD
– 80 –
– 81 –
6-13. SCHEMATIC DIAGRAM – POWER SECTION –
ZS-M7
6-14. PRINTED WIRING BOARDS – POWER SECTION –
r
Semiconductor
Location
Ref. No.
Location
D351
C-3
D352
C-2
D353
C-2
D951
C-6
D952
C-5
(EXCEPT US MODEL)
D-952
C-14
(US MODEL)
D953
D-6
(EXCEPT US MODEL)
D-953
D-14
(US MODEL)
D954
E-6
D955
F-7
D956
D957
D958
E-8
F-7
F-8
IC351
D-1
Q151
Q251
Q351
Q352
C-2
C-2
C-2
C-2
Note:
• X : parts extracted from the component side.
• b : Pattern of the rear side.
• b : Pattern on the side which is seen.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
Note: The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
– 82 –
– 83 –
– 84 –
– 85 –
– 86 –
6-15. SCHEMATIC DIAGRAM – DG SECTION –
r
Refer to page 102 for IC Block Diagrams.
6-16. PRINTED WIRING BOARDS – DG SECTION –
r
Waveforms – DC Section –
r
ZS-M7
Refer to page 53 for Circuit Boards Location.
Semiconductor Location
Ref. No.
1
r
Location
Ref. No.
Location
D551
D552
G-6
J-2
Q503
Q504
Q507
H-3
H-2
J-3
IC501
IC502
IC503
IC504
IC505
H-4
D-8
G-2
J-1
C-6
Q509
Q510
Q511
Q520
Q521
H-4
H-2
I-4
I-6
I-6
IC506
IC507
K-7
K-8
Q501
Q502
H-1
K-2
Q522
Q551
Q552
Q553
Q554
I-5
G-6
G-5
G-6
G-5
0.63 Vp-p
12 MHz
IC502 @¶
VOLT/DIV : 0.2 V AC
TIME/DIV : 20 nsec
2
2.3 Vp-p
32.768 kHz
IC502 @¢
VOLT/DIV : 0.5 V AC
TIME/DIV : 10 µsec
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
%
: indicates tolerance.
¢
•
: internal component.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD STOP
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E : MD PLAY
q : MD REC
J : CD
– 87 –
– 88 –
– 89 –
Note:
• X : parts extracted from the component side.
• b : Pattern on the side which is seen.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
– 90 –
– 91 –
ZS-M7
6-18. SCHEMATIC DIAGRAM – FRONT KEY SECTION –
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
r Waveforms
– Front Key Section –
1
1.0 Vp-p
6 MHz
IC401 $º (XTAL)
VOLT/DIV : 0.2 V AC
TIME/DIV : 50 nsec
– 97 –
– 98 –
– 99 –
IC101 CXA2523R
PLL
A
GRV
IVR
AA
B
5
IVR
C
55 RFI
+
–
6
IVR
DIN 21
51 ASYO
D
IVR
E
F
EE
+
–
FF
50
MPX IN
LPF1/BAND
LPF2/MO-ST
VCO
PEAK
DET OUT
RF
IF OUT
RF AGC
OSC OUT
AGCI
VCC1
7
ST
DET
3
4
8
9
10
11
–2
TG
–1
TESW
TG
26 TE
TEA
3T
25 WBLADJ
VI CONV
EQ
AUXSW
BGR
COMMAND
+
–
VREF
SCRI - PARA
DECODE
VM1
IN1F
IN1R
VDD
21
20
19
18
17
INTERFACE
VCC
OUT1F
22
24
3TADJ
PGND1
23
22 23
EQADJ
OUT1R
24
21
VREF
VM12
25
20
F0CNT
OUT2R
26
19
XSTBY
PGND2
27
18
XLAT
OUT2F
28
17
SCLK
VM2
29
16
SWDT
IN2F
30
15
TEMPR
IN2R
31
14
TEMPI
CAPA+
32
13
GND
CAPA–
IC152 BH6511FS
X IN
2
X OUT
1
FM IN
16
PHASE
DET
REFERENCE DIVIDER
19 PD 1
BUFFER
AM IN
15
CE
3
CK
4
DA
5
CD
6
P0
7
P1
BAND
8
P2
NU
14
MAIN COUNT
r
VDD
I/O
CTL
IF COUNT
CTL
20 BIT COUNT
9
10
12
IC Block Diagrams (DG Section)
IC504 RH5RL33AA-T1
GND
1
VIN
2
VREF
PRE DRIVE
6
7
8
9
10
VG
IN4R
IN4F
VM4
OUT4F
PGND4
OUT4R
VM34
OUT3R
11
12
13
14
15
16
PSB
5
IN3R
4
PSB
IN3F
3
INTERFACE
VM3
2
AMP
OUT3F
1
GND
AMP
PGND3
AMP
AMP
INTERFACE
– 100 –
17 VDD 2
20 VSS
13 IF IN
PRE DRIVE
PRE DRIVE
11 PD 2/ P 5
LOC/DX
18 VDD 1
PRESCALER
WBL
FF'
APC 11
PRE DRIVE
12
28 SE
SEA
APCREF 12
CHARGE
PUMP.
OSC
MUTE
SHIFT REGISTER LATCH
+
–
PD 10
MVCI
D3
D2
D0
D1
XWE
XRAS
A09
XCAS
XOE
DVSS
A11
A08
A07
A06
A05
A04
A10
A00
A01
A02
A03
DVDD
2
27 CSLED
FBAL
GSW IV
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
AMP
6
FM
DET
29 ADFM
–1
PTGR
–
+
–
+
EE'
+
–
FS256
1
DD
+
–
9
ADDRESS/DATA BUS A00 - A11, D0 - D3
XBCK
ADIP
AGC
WBL
ATA
–2
DRAM
INTERFACE
AMP
5
LEVEL
DET
IC2 BU2615FS
–
–
+
+
+
–
8
LRCK 25
AMP
AM
IF
DET
WBL
IVR
AMP
FM
IF
30 ADIN
EFB
INTERFACE
AGC
FM
RF
FEA
CC
+
–
7
IVR
26 27 28
AM
DET
AM
MIX
BPFC
ABCDA
52 ASYI
DADT 24
AM/FM
ST/MONO
SW
35 ABCD
33 AUX
53 AVDD
ATRAC
ENCODER/DECODER
AF
BUFF
BPF22
54 BIAS
DOUT 22
ADDT 23
IF
BUFF
FM
MIX
34 FE
+
+
–
–
BUFF
1/8DIV
31 ADAGC
BB
BUFF
36 BOTM
PBH
32 ADFG
+
–
FM
OSC
TEMP
WBL
+
+
+
+
FM MPX
AM
OSC
P5
D VSS 20
FM OSC
COMPO
BOTTOM
–1
GRVA
+
–
4
57 PDO
COMP
SAMPLING
RATE
CONVERTER
13
ULLOCK
DIGITAL
AUDIO
I/F
14
58 PCO
EACH
BLOCK
TESTG 19
AM OSC
COMPP
–2
56 AVSS
XTSL 18
WBL
PEAK
OSCI 16
OSCO 17
FM RF OUT
ADDC
3T
PTGR
–
1
–
–2
59 FILI
TX 15
CLOCK
GENERATOR
15
R OUT
3
60 FILO
EFM/ACIRC
ENCODER/
DECODER
SHOCK RESISTANT
MEMORY CONTROLLER
XINT 14
16
L OUT
61 CLTV
17
AM
RF
–2
62 PEAK
RECP 13
18
ST IND
CVB
VC
PEAK3T
P-P
3T
63 BOTM
SUBCODE
PROCESSOR
19
P6
FM-L
SQSY 11
DQSY 12
–1
CFST
64 ABCD
APC
20
P4
MW-L
XRST 10
21
QUAD
65 FE
22
GND2
2
HLPT
66 AUX1
ANALOG
MUX
23
P3
LW-L
SENS 9
24
EQ
AM IF IN
J
–1
–
–2
–
67 VC
A/D
CONVERTER
EQ
USRC
BPF3T
1
69 AVDD
SCLK 6
RF AGC
+
–
RFA2
I
70 ADRT
SERVO
DSP
37
FM IF IN
72 AVSS
EACH
BLOCK
38
VCC2
73 SE
68 ADIO
CPU I/F
39
DET
71 ADRB
XLAT 7
40
AGC
74 TE
ADIP
DEMODULATOR/
DECODER
SRDT 8
41
75 AUX2
MNT3 4
SWDT 5
43 42
MIX OUT
AUTO
SEQUENCER
EACH
BLOCK
44
USROP
AM RF IN
–
+
OPO
OPN
45
IC1 TA2008AN
GND1
MNT2 3
PWM
GENERATOR
SPINDLE
SERVO
MONITOR
CONTROL
46
–
+
MNT1 2
47
92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
RFA1
MNT0 1
RFO
DCHG
APC
ADFG
F0CNT
XLRF
CKRF
DTRF
APCREF
LDDR
TRDR
TFDR
DVDD
FFDR
FRDR
FS4
SRDR
SFDR
94 93
48
IC Block Diagrams – Tuner Section –
FM RF IN
100 99 98 97 96 95
SPRD
SPFD
FGIN
TEST1
TEST2
TEST3
DVSS
EFMO
IC121 CXD2652AR
MORFI
r
MORFO
IC Block Diagrams – BD Section –
+
–
r
– 101 –
3
OUT
– 102 –
r
IC Block Diagrams – Main Section –
RF_O
RF_I
CP
CB
CC1
CC2
FOK
37
RF_M
PDO
38
RFTC
PD1
39
LD
PD2
IC701 CXA1992BR
36
35
34
33
32
31
30
29
28
27
VEE
PD2 IV
AMP
RF
SUMMING
AMP
PD1 IV
AMP
FE_
BIAS 40
VCC
LASER POWER CONTROL
F IV AMP
VCC
VCC
VCC
FE AMP
E IV AMP
24
SENS1
24
C. OUT
IFB5
IFB6
IFB4
IFB3
IFB2
IFB1
DFCT
23
XRST
22
DATA
21
XLT
20
CLK
19
LOCK
18
VCC
17
ISET
16
SL_O
15
SL_M
14
SL_P
VEE
LEVEL S VEE
TGFL
LDON
E-F BALANCE
WINDOW COMP.
MIRR
FOK
TRK. GAIN
WINDOW COMP.
LPF1 46
FOH
FOL
TGH
TGL
BALH
BALL
ATSC
TZC
FZC
TEI 47
ATSC 48
TTL
↓
IIL
IIL DATA REGISTER,
INPUT SHIFT REGISTER,
ADDRESS DECODER,
SENS SELECTOR,
OUTPUT DECODER
VCC
ATSC
WINDOW
COMP.
DFCTO IFB1-6 FS1-4
BAL1-4
TOG1-4
TZC 49
DFCT
TZC COMP.
IIL
↓
TTL
MIRR
LPC
TEO 45
VCC
CC1
FO. BIAS
WINDOW
COMP.
DFCT1
VEE
LPCL
TGFL
BAL1
TOG1
TOG2
TOG3
TOG4
VEE
TG1-2 TM1-7 PS1-4
ISET
TM1
VCC
TDFCT 50
VCC
TRACKING
PHASE COMPENSATION
TG1
TM4
VC 51
VCC
VCC
SENS2
VEE
BAL2
BAL3
BAL4
EI 43
VEE 44
IIL
↓
TTL
VEE
F 41
E 42
26
APC
VEE
FOCUS
PHASE COMPENSATION
FZC 52
DFCT
TM6
TM7
FS1
Charge
up
FZC COMP.
TM5
TM3
VEE
FS2
VCC
VEE
FSET
TG2
FS4
10
11
12
13
TA_O
FLB
9
TA_M
FGD
8
FSET
FDFCT
7
TG2
FEI
6
TGU
5
SRCH
4
FE_M
3
FE_O
2
FEO
VEE
1
– 103 –
TM2
VSS
EXCK
SBSO
SCOR
WFCK
ENPHI
EMPH
DOUT
C4M
XTSL
C2PO
GFS
XPCK
XUGF
VDD
VSS
BCKI
BCK
PCMDI
PCMD
IC703 CXD2589Q
60
59 58 57
56
55
54 53 52 51 50
49
48
47
46
45
44
43
42
41
VDD 61
SYSM 62
SERIAL-IN
INTERFACE
PWM
40 LRCKI
39 LRCK
AVSS 63
38 ASYO
OVER SAMPLING
DIGITAL FILTER
37 ASYI
ASYMMETRY
CORRECTOR
EFM
DEMODULATOR
AVDD 64
36 BIAS
35 RF
AOUT1
AIN1
LOUT1
AVSS
XVDD
XTAI
65
66
67
68
69
70
3rd-ORDER
NOISE SHAPER
34 AVDD
33 CLTV
TIMING
LOGIC
ERROR
CORRECTOR
16K
RAM
32 AVSS
SUB CODE
PROCESSOR
DIGITAL
PLL
PWM
XTAO 71
31 FILI
30 FILO
29 PCO
XVSS 72
DIGITAL
OUT
D/A
INTERFACE
AVSS 73
OSC
LOUT2 74
AIN2 75
AOUT2 76
28 V16M
27 VCTL
26 VCKI
25 VPCO1
CLOCK
GENERATOR
24 TES1
AVDD 77
23 TES0
AVSS 78
CPU
INTERLACE
22 PWMI
DIGITAL
CLV
SERVO
AUTO
SEQUENCER
XRST 79
21 MDP
13
14
15
16
17
18
19
20
FOK
VDD
VSS
DATA
12
XLON
SENS
11
SPOB
SQSO
10
SPOA
SQCK
9
CLKO
VSS
8
XLTO
7
DATO
6
SEIN
5
CNIN
4
XLAT
2 3
CLOK
1
LMUTE
RMUTE
VDD 80
– 104 –
F–
F+
FIN
(FIN)
VREF
VCC
VCC
(TIN)
TIN
T–
T+
VREF
SP I
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VCC
DRIVE
DRIVE
DRIVE
VCC
DRIVE
GND
IC702 BA6898FP
LEVEL SHIFT
LEVEL SHIFT
THERMAL
SHUT DOWN
DRIVER MUTE
REG VOLTAGE DOWN,
BIAS VOLTAGE DOWN,
THERMAL SHUT DOWN
MONITOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SL –
SL +
SL IN
RESET
REGB
REGO
MUTE
GND
(SP IN)
SP IN
SP –
SP +
GND
SPO
DRIVE
DRIVE
LEVEL SHIFT
DRIVE
DRIVE
LEVEL SHIFT
IC301 TDA7439D013TR
SPKA ATT
RIGHT
SPKA ATT
LEFT
R IN3
1
28
R IN4
27
LOUT
26
ROUT
25
AGND
24
VS
23
CREF
22
SDA
21
SCL
20
DIG-GND
19
TREBLE (R)
18
TREBLE (L)
17
MIN (L)
16
MOUT (L)
15
BOUT (L)
14
BIN (L)
G
R IN2
2
R IN1
3
L IN1
4
L IN2
5
VREF
0/30dB
2dB STEP
TCBUS
DECODER •
LATCH
G
L IN3
6
L IN4
7
MUXOUTL
8
MUXOUTR
9
MIN (R)
10
MOUT (R)
11
BIN (R)
12
BOUT (R)
13
SUPPLY
INPUT
MULTIPLEXER
GAIN
VOLUME
VOLUME
TREBLE
TREBLE
MIDDLE
MIDDLE
BASS
BASS
– 105 –
SECTION 7
EXPLODED VIEWS
NOTE :
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference
number in the exploded views are not
supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
• Abbreviation
EE
: East European
JE
: Tourist
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
7-1. FRONT CABINET SECTION
32
25
10
32 8
27
9
12
10
7
28
21
11
SP101 #11
#11
6
32
17
20
12
18
#4
12
12
29 19
30
23
31
24
12
15
16
#4
25
12
10
12
33
2
13
12
#11
22
#11
2
5
28
14
SP201
4
27
26
#4
#4
5
1
#4
2
3
Ref. No.
Part No.
Description
1
* 2
3
4
5
X-3374-653-1
4-963-075-01
X-3374-656-1
X-3374-655-1
3-023-288-01
CABINET (FRONT) SUB ASSY
CATCHER
NET (R) ASSY, SP
NET (L) ASSY, SP
SPACER (RUBBER FOOT)
6
7
8
9
10
3-019-664-01
3-019-652-01
3-019-659-01
3-019-658-01
3-022-992-01
KNOB (JOG)
PANEL
BUTTON (CAN/ENT)
BUTTON (EDIT)
SCREW, WASHER HEAD
11
12
13
* 14
* 14
3-019-659-11
4-931-757-31
3-020-473-01
1-668-258-31
1-668-258-21
BUTTON (CAN/ENT)
SCREW(DIA.2.6X8)(IT3B),TAPPING
SCREW (3X45)
RELAY BOARD (US)
RELAY BOARD (EXCEPT US)
* 15
* 15
16
* 17
* 17
1-668-246-21
1-668-246-31
3-019-660-01
1-668-245-21
1-668-245-31
RIGHT KEY BOARD (EXCEPT US)
RIGHT KEY BOARD (US)
BUTTON (VOL)
TOP KEY BOARD (EXCEPT US)
TOP KEY BOARD (US)
18
Remark
Ref. No.
Part No.
Description
19
19
* 20
* 20
3-019-661-01
3-019-661-11
1-668-243-21
1-668-243-31
BUTTON (POWER) (US)
BUTTON (POWER) (EXCEPT US)
LEFT KEY BOARD (EXCEPT US)
LEFT KEY BOARD (US)
21
* 22
* 22
23
24
3-019-663-01
A-3321-557-A
A-3321-539-A
3-020-475-01
3-025-864-01
BUTTON (MEGABASS)
FRONT KEY BOARD, COMPLETE (EXCEPT US)
FRONT KEY BOARD, COMPLETE (US)
HOLDER (LED)
COVER (REMOTE CONTROL WINDOW)
25
* 26
27
28
29
4-931-757-91
3-378-433-01
3-026-848-01
3-026-849-01
3-338-596-01
SCREW (DIA. 2.6) (IT3B)
CUSHION, SARANET
CUSHION
CUSHION
CUSHION (EXCEPT US)
30
31
32
33
3-022-197-01
3-026-450-01
3-026-295-01
3-026-779-01
CUSHION (JACK)
CUSHION
BLIND (BOSS)
CUSHION
SP101
SP201
1-505-829-11 SPEAKER (8cm) (L-CH)
1-505-829-11 SPEAKER (8cm) (R-CH)
3-019-662-01 BUTTON (CLOCK)
– 106 –
Remark
US Model
7-2. REAR CABINET SECTION
67
67
ANT1
61
not
supplied
51
not supplied
65
F953
#9
#9
63
F952
66
not
supplied
58
59
60
EXCEPT
US Model
#14
58
#10
#9
F951
62
#14
64
70
58
#13
68
EXCEPT
US Model
T951
#9
71 56
57
#15
69
#9
53
#4
#9
70
#9
#9
#9
52
69
#9
#9
not
supplied
55
#9
54
#9
Ref. No.
Part No.
Description
51
52
52
53
53
3-009-989-01
1-668-255-21
1-668-255-31
1-668-254-21
1-668-254-31
CUSHION (HANDLE)
AM ANT BOARD (EXCEPT US)
AM ANT BOARD (US)
FM ANT BOARD (EXCEPT US)
FM ANT BOARD (US)
54
* 55
* 55
56
57
3-019-682-01
A-3321-562-A
A-3321-536-A
3-019-683-01
3-019-665-01
BRACKET (TUNER)
TUNER BOARD, COMPLETE (EXCEPT US)
TUNER BOARD, COMPLETE (US)
TERMINAL BOARD, ANTENNA
HANDLE
58
59
60
* 61
* 61
1-533-293-11
4-812-134-00
3-023-950-01
A-3321-535-A
A-3321-561-A
FUSE HOLDER
RIVET (DIA. 3.5), NYLON
COVER, FUSE
TRANS BOARD, COMPLETE (US)
TRANS BOARD, COMPLETE (EXCEPT US)
62
63
64
* 65
3-023-747-01
3-019-668-01
3-019-681-01
3-703-244-00
PACKING (CORD)
BRACKET (TRANSFORMER)
BRACKET (POWER CORD)
BUSHING (2104), CORD
*
*
*
*
Remark
Ref. No.
66
Part No.
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
Description
Remark
4-931-757-31 SCREW (DIA. 2.6X8) (IT3B)
! 67
! 67
68
68
69
1-783-531-31
1-575-651-21
X-3376-404-1
X-3376-405-1
3-023-746-11
CORD, POWER (US)
CORD, POWER (EXCEPT US)
CABINET REAR ASSY (US)
CABINET REAR ASSY (EXCEPT US)
PACKING (TU)
70
71
ANT1
! F951
! F951
3-378-434-01
3-378-121-01
1-501-480-11
1-576-101-11
1-532-502-51
CUSHION, SARANET
CUSHION, SARANET
ANTENNA, TELESCOPIC
FUSE (1.25A/125V) (US)
FUSE, TIME LAG (T1.25AL/250V) (EXCEPT US)
! F952
! F952
! F953
! F953
! T951
1-533-310-11
1-532-506-51
1-532-465-51
1-576-107-11
1-433-445-11
FUSE, GLASS TUBE (6.3A/125V) (US)
FUSE, TIME LAG (T6.3AL/250V) (EXCEPT US)
FUSE, TIME LAG (T3.15AL/250V) (EXCEPT US)
FUSE (3.15A/125V) (US)
TRANSFORMER, POWER (US)
! T951
1-433-444-11 TRANSFORMER, POWER (EXCEPT US)
– 107 –
7-3. CHASSIS SECTION
105
not supplied
#9
112
#9
#9
106
#9
#9
103
104
FL401
#9
not supplied
112
not supplied
#9
108
not supplied
#9
109
113
110
107
not supplied
109
#9
#9
#9
102
103
111
#9
#9
113
#9
101
not supplied
Ref. No.
*
*
*
*
*
*
*
*
Part No.
Description
Ref. No.
Part No.
Description
101
101
102
102
103
1-668-249-21
1-668-249-31
1-668-250-31
1-668-250-21
3-321-041-41
LINE IN BOARD (EXCEPT US)
LINE IN BOARD (US)
HP BOARD (US)
HP BOARD (EXCEPT US)
SCREW (M1.7X5), TAPPING
Remark
* 107
* 107
108
109
110
A-3321-544-A
A-3321-565-A
1-783-539-11
4-931-757-31
1-783-537-11
MAIN BOARD, COMPLETE (US)
MAIN BOARD, COMPLETE (EXCEPT US)
WIRE, PARALLEL (FFC) (15 CORE)
SCREW(DIA.2.6X8)(IT3B),TAPPING
WIRE, PARALLEL (21 CORE)
104
105
105
106
106
3-019-671-01
A-3323-036-A
A-3323-029-A
A-3321-573-A
A-3321-552-A
HOLDER (FL)
FL BOARD, COMPLETE (EXCEPT US)
FL BOARD, COMPLETE (US)
AUDIO BOARD, COMPLETE (EXCEPT US)
AUDIO BOARD, COMPLETE (US)
111
* 112
113
FL401
1-783-538-11
3-703-150-11
3-031-392-01
1-517-744-11
WIRE, PARALLEL (FFC) (13 CORE)
CLAMP
CUSHION (CD)
INDICATOR TUBE, FLUORESCENT
– 108 –
Remark
7-4. MD SECTION (1)
(MDM-3EG)
not supplied
154
not supplied
154
154
157
154
154
157
158
158
#2
154
not supplied
not supplied
164
not supplied
163
155
156
#2
#2
162
161
168
153
160
152
#6
159
not supplied
151
#2
165
167
Ref. No.
Part No.
Description
* 151
* 151
* 152
153
154
A-3321-571-A
A-3321-550-A
A-3293-900-A
1-660-966-11
3-028-625-01
DG BOARD, COMPLETE (EXCEPT US)
DG BOARD, COMPLETE (US)
BD BOARD, COMPLETE
OP RELAY FLEXIBLE BOARD
SCREW (M1.7X2) (S TITE)
155
156
157
158
159
X-4947-825-1
4-987-736-11
4-628-167-01
4-987-327-11
1-783-542-11
SHUTTER ASSY
SHAFT (SHUTTER)
SCREW, STEP
INSULATOR
WIRE, PARALLEL (FFC) (29 CORE)
#6
166
Remark
Ref. No.
Part No.
Description
160
161
162
163
164
1-783-540-11
1-790-045-11
1-777-517-11
4-987-910-01
4-986-959-01
WIRE, PARALLEL (FFC) (19 CORE)
WIRE, PARALLEL (26 CORE)(60mm)
WIRE, PARALLEL (15 CORE)
SPRING (O/C), TENSION
WASHER
165
* 166
167
168
1-790-046-11
1-671-517-11
3-029-176-01
7-627-553-27
WIRE, PARALLEL (26 CORE)(172mm)
FILTER BOARD
SCREW (M1.7X4)
SCREW,PRECISION +P 2X2.5
– 109 –
Remark
Ver 1.2 2001.07
7-5. MD SECTION (2)
(MDM-3EG)
201
223
#2
#3
not supplied
202
206
203
209
#2
208
210
207
223
#5
221
#5
211
not supplied
205
212
M901
M902
M903
214
213
#3
219
216
215
HR901
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
217
218
220
Ref. No.
Part No.
Description
201
* 202
203
205
* 206
A-4672-138-A
4-983-439-01
3-953-235-01
3-342-375-11
4-979-890-11
SLIDER COMPLETE ASSY
BRACKET (DAMPER)
DAMPER, OIL
SCREW (M1.7X1.4), SPECIAL
RETAINER (GEAR)
207
208
209
210
211
4-979-898-01
4-979-899-01
4-979-897-01
4-979-885-01
4-979-906-11
GEAR (LB)
GEAR (LC)
GEAR (LA)
LEVER (HEAD UP)
SPRING (LEAD SCREW)
* 212
* 213
214
215
4-984-556-01
1-661-774-11
A-3304-200-A
4-963-914-02
SHAFT (MAIN SHAFT)
SW BOARD
SCREW ASSY, LEAD
RACK (INSERTER)
Remark
Ref. No.
216
! 217
218
219
220
* 221
223
HR901
M901
M902
M903
– 110 –
Part No.
Description
Remark
3-366-890-11 SCREW (M1.4)
A-4672-541-A
4-987-061-01
4-988-560-01
4-955-841-11
4-983-511-02
OPTICAL PICK-UP KMS-260B
SPACER (RACK)
SCREW (+P1.7X6)
SCREW
PIN (OUTSERT)
3-028-625-01
1-500-396-11
A-4672-135-A
A-4672-133-A
A-4672-134-A
SCREW (M1.7X2) (S TITE)
HEAD, OVER WRITE
MOTOR ASSY, SPINDLE
MOTOR ASSY, SLED (INCLUDING GEAR)
MOTOR ASSY, LOADING (INCLUDING GEAR)
7-6. CD SECTION
(VLM-ZSM7-142)
267
#8
254
264
#8
#8
M691
266
not supplied
268
269
#8
273
#8
#8
#8
#1
262
272
270
#8
#16
263
265
271
254
260
#8
261
CDM-2411AAA
258
252
259
258
#8
253
255
274
256
251
275
258
257
#7
#7
Ref. No.
Part No.
Description
* 251
* 252
* 253
254
255
3-017-025-01
3-017-012-01
3-017-014-01
3-017-027-01
3-017-016-01
COVER (R), SIDE
PLATE (R), SIDE
SLIDER (R)
GEAR (C)
SHAFT, TRAY
256
257
258
* 259
* 260
4-975-811-01
3-017-022-01
4-975-762-11
1-667-046-11
3-020-624-01
INSULATOR
TRAY (BOTTOM), CD
INSULATOR
PICK-UP RELAY BOARD
TRAY (TOP), CD
261
262
* 263
3-020-492-01 LID, CD
X-3374-204-1 WINDOW ASSY, CD
3-017-013-01 SLIDER (L)
Remark
Ref. No.
Part No.
* 264
* 265
3-017-035-01 COVER (L), SIDE
3-017-011-01 PLATE (L), SIDE
266
* 267
268
269
270
3-017-017-01
1-667-045-11
3-017-031-01
3-017-032-01
3-017-030-01
LEVER, DETECTION
LOADING BOARD
GEAR (A)
GEAR (B)
BELT
271
* 272
273
* 274
* 275
M691
A-3311-798-A
3-017-036-01
2-627-174-01
3-378-138-01
3-022-456-01
1-698-999-11
DRIVE ASSY
CHASSIS, GEAR
PULLEY (M)
CUSHION, SARANET
SPACER (VLM)
MOTOR, DC (LOADING)
– 111 –
Description
Remark
7-7. OPTICAL PICK-UP SECTION
(CDM-2411AAA)
306
M802
307
M801
308
#12
305
309
S901
304
303
310
302
301
311
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
Ref. No.
301
302
303
304
305
306
* 307
Part No.
Description
A-3303-970-A
3-318-203-11
1-690-530-21
4-972-163-01
4-974-003-01
SCREW ASSY, FEED
SCREW (B1.7X6), TAPPING
LEAD (WITH CONNECTOR)
SPRING, SLED
GEAR (B)
3-719-401-11 SCREW (B1.7), TAPPING
4-972-162-01 CHASSIS
Remark
Ref. No.
Part No.
308
!309
310
1-660-965-11 SLIDE FLEXIBLE BOARD
X-4946-311-1 OPTICAL PICK-UP (DAX-11A)
4-972-165-01 RACK
311
M801
M802
S901
– 112 –
4-973-631-01
A-3303-403-A
A-3320-300-A
1-571-099-21
Description
Remark
SCREW
MOTOR ASSY, SLED (INCLUDING GEAR)
MOTOR ASSY, TURNTABLE (SPINDLE)
SWITCH (1 KEY) (LIMIT)
SECTION 8
ELECTRICAL PARTS LIST
NOTE :
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable
• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
AM ANT
• SEMICONDUCTORS
In each case, u : µ , for example :
uA.... : µ A.... , uPA.... : µ PA....
uPB.... : µ PB.... , uPC.... : µ PC....
uPD.... : µ PD....
• CAPACITORS
uF : µ F
• COILS
uH : µ H
• Abbreviation
EE
: East European
JE
: Tourist
Part No.
1-668-255-21 AM ANT BOARD (EXCEPT US)
1-668-255-31 AM ANT BOARD (US)
************
C358
C359
C360
1-126-960-11 ELECT
1-104-664-11 ELECT
1-126-963-11 ELECT
1uF
47uF
4.7uF
20%
20%
20%
50V
25V
50V
< CAPACITOR >
C361
C362
C363
C364
1-163-009-11
1-163-251-11
1-127-508-00
1-127-508-00
0.001uF
100PF
2.2uF
2.2uF
10%
5%
20%
20%
50V
50V
25V
25V
100PF
5%
50V
(EXCEPT US)
Ref. No.
When indicating parts by reference number, please include the board.
Ref. No.
1-163-251-11 CERAMIC CHIP
Remark
The components identified by mark !
or dotted line with mark ! are critical
for safety.
Replace only with part number specified.
*
*
C58
Description
AUDIO
Part No.
* CN351
* CN352
* CN353
1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P
< POST PIN >
CP50
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
1-573-489-21 PIN, CONNECTOR (PC BOARD) 11P
1-564-507-11 PLUG, CONNECTOR 4P
1-564-519-11 PLUG, CONNECTOR 4P
< POST PIN >
1-536-354-00 PIN, POST
CP7
< TERMINAL >
1-536-833-31 TERMINAL BOARD (AM ANTENNA)(US)
1-536-833-31 TERMINAL BOARD (MW/LW ANTENNA)
(EXCEPT US)
************************************************************
1-536-354-00 PIN, POST
< DIODE >
TB1
TB1
D351
D352
D353
8-719-988-62 DIODE 1SS355
8-719-988-62 DIODE 1SS355
8-719-988-62 DIODE 1SS355
A-3321-552-A AUDIO BOARD, COMPLETE (US)
A-3321-573-A AUDIO BOARD, COMPLETE (EXCEPT US)
**********************
*
*
Remark
< CONNECTOR >
< CONNECTOR >
CN3
Description
< IC >
IC351
8-759-333-16 IC LA4705NA
< TRANSISTOR >
< CAPACITOR >
C151
C152
C153
C154
C155
1-126-963-11
1-163-009-11
1-136-165-00
1-136-165-00
1-126-964-11
ELECT
CERAMIC CHIP
FILM
FILM
ELECT
4.7uF
0.001uF
0.1uF
0.1uF
10uF
20%
10%
5%
5%
20%
50V
50V
50V
50V
50V
C251
C252
C253
C254
C255
1-126-963-11
1-163-009-11
1-136-165-00
1-136-165-00
1-126-964-11
ELECT
CERAMIC CHIP
FILM
FILM
ELECT
4.7uF
0.001uF
0.1uF
0.1uF
10uF
20%
10%
5%
5%
20%
50V
50V
50V
50V
50V
C351
C352
C353
C354
C355
1-124-994-11
1-128-551-11
1-126-047-75
1-163-251-11
1-163-251-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
22uF
4.7uF
100PF
100PF
20%
20%
20%
5%
5%
10V
25V
50V
50V
50V
C356
C357
1-136-165-00 FILM
1-117-943-11 ELECT
0.1uF
6800uF
5%
20%
50V
25V
Q151
Q251
Q351
Q352
8-729-920-31
8-729-920-31
8-729-031-43
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC343TK
DTC343TK
IMD9A-T108
2SC1623-L5L6
< RESISTOR >
R151
R152
R153
R154
R155
1-216-657-11
1-216-659-11
1-216-298-00
1-216-298-00
1-216-053-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.8K
2.2K
2.2
2.2
1.5K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R251
R252
R253
R254
R255
1-216-657-11
1-216-659-11
1-216-298-00
1-216-298-00
1-216-053-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.8K
2.2K
2.2
2.2
1.5K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R351
1-216-077-00 METAL CHIP
15K
5%
1/10W
– 113 –
AUDIO
Ref. No.
R352
R353
R354
R355
BD
Part No.
Description
1-216-073-00
1-216-059-00
1-216-097-91
1-216-121-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
Remark
10K
2.7K
100K
1M
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R356
1-216-073-00 METAL CHIP
10K
5%
1/10W
R357
1-216-049-91 RES,CHIP
1K
5%
1/10W
************************************************************
A-3293-900-A BD BOARD, COMPLETE
******************
*
< CAPACITOR >
Part No.
Description
C168
C169
C171
C181
1-163-038-91
1-104-851-11
1-163-038-91
1-126-206-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
10uF
0.1uF
100uF
Remark
C182
C183
C184
C185
C187
1-163-038-91
1-163-038-91
1-107-836-11
1-164-611-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.1uF
22uF
0.001uF
100uF
C188
C189
C190
C191
C195
1-163-021-91
1-163-989-11
1-126-206-11
1-163-038-91
1-164-346-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.033uF
100uF
0.1uF
1uF
C196
C197
1-163-038-91 CERAMIC CHIP
1-163-038-91 CERAMIC CHIP
C101
C102
C103
C104
C105
1-104-851-11
1-163-038-91
1-104-851-11
1-104-851-11
1-163-021-91
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
10uF
0.1uF
10uF
10uF
0.01uF
20%
C106
C107
C108
C109
C110
1-163-275-11
1-163-038-91
1-163-038-91
1-163-037-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.1uF
0.022uF
0.1uF
5%
C111
C112
C113
C115
C116
1-164-344-11
1-163-017-00
1-107-682-11
1-164-489-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.068uF
0.0047uF
1uF
0.22uF
0.022uF
10%
5%
10%
10%
10%
25V
50V
16V
16V
25V
C117
C119
C121
C122
C123
1-164-004-11
1-104-851-11
1-126-206-11
1-163-021-91
1-163-038-91
CERAMIC CHIP
TANTAL. CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
100uF
0.01uF
0.1uF
10%
20%
20%
10%
25V
10V
6.3V
50V
25V
D101
D181
D183
C124
C127
C128
C129
C130
1-163-038-91
1-163-038-91
1-163-021-91
1-107-823-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.47uF
100PF
10%
10%
5%
25V
25V
50V
16V
50V
IC101
IC103
IC121
IC122
IC123
8-752-074-77
8-729-903-10
8-752-384-47
8-759-234-20
8-759-242-70
IC
IC
IC
IC
IC
CXA2523R
FMW1
CXD2652AR
TC7S08F
TC7WU04F
C131
C132
C133
C134
C135
1-163-023-00
1-107-823-11
1-163-017-00
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.015uF 5%
0.47uF
10%
0.0047uF 5%
0.1uF
0.1uF
50V
16V
50V
25V
25V
IC124
IC152
IC171
IC181
IC192
8-759-473-29
8-759-430-25
8-759-428-58
8-759-095-65
8-759-426-95
IC
IC
IC
IC
IC
MN41V4400SJ-08-T1
BH6511FS
XL24C01AF-E2
TC74ACT540FS
L88MS33T-TL
C136
C141
C142
C143
C144
1-126-206-11
1-163-038-91
1-163-251-11
1-163-251-11
1-163-251-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
100PF
100PF
100PF
6.3V
25V
50V
50V
50V
C146
C151
C152
C153
C156
1-163-038-91
1-126-206-11
1-163-038-91
1-163-021-91
1-163-038-91
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.1uF
0.01uF
0.1uF
C158
C160
C161
C163
C164
1-163-019-00
1-104-601-11
1-104-601-11
1-163-021-91
1-163-021-91
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0068uF
10uF
10uF
0.01uF
0.01uF
C167
1-163-038-91 CERAMIC CHIP
0.1uF
20%
20%
10%
10%
20%
5%
5%
5%
20%
10%
10%
20%
20%
10%
10%
10V
25V
10V
10V
50V
Ref. No.
50V
25V
25V
25V
25V
20%
10%
20%
25V
25V
8V
500V
6.3V
10%
10%
20%
0.1uF
0.1uF
50V
25V
6.3V
25V
16V
25V
25V
< CONNECTOR >
CN101
CN102
CN103
CN104
CN106
1-766-508-11
1-778-461-11
1-778-460-11
1-766-898-21
1-770-698-11
CONNECTOR, FFC/FPC (ZIF) 22P
CONNECTOR, FFC/FPC 29P
CONNECTOR, FFC/FPC 19P
HOUSING, CONNECTOR(PC BOARD)4P
CONNECTOR, FFC/FPC 15P
CN110
1-774-731-21 PIN, CONNECTOR (PC BOARD) 5P
< DIODE >
25V
6.3V
25V
50V
25V
50V
10V
10V
50V
50V
20%
25V
10V
25V
6.3V
20%
8-719-988-62 DIODE 1SS355
8-719-046-86 DIODE F1J6TP
8-719-046-86 DIODE F1J6TP
< IC >
< COIL >
L101
L102
L103
L105
L106
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
L121
L122
L151
L152
L153
1-414-235-11
1-414-235-11
1-412-622-51
1-412-622-51
1-412-039-51
FERRITE BEAD INDUCTOR
INDUCTOR CHIP
INDUCTOR
10uH
INDUCTOR
10uH
INDUCTOR CHIP 100uH
L154
L161
L162
1-412-039-51 INDUCTOR CHIP 100uH
1-414-235-11 FERRITE BEAD INDUCTOR
1-414-235-11 FERRITE BEAD INDUCTOR
25V
– 114 –
BD
Ref. No.
Part No.
Description
Remark
Ref. No.
< TRANSISTOR >
Q101
Q102
Q103
Q104
Q162
8-729-028-91
8-729-026-53
8-729-028-99
8-729-028-99
8-729-101-07
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA144EUA-T106
2SA1576A-T106-QR
DTC114YUA-T106
DTC114YUA-T106
2SB798-DL
Q163
Q180
Q181
Q182
8-729-028-91
8-729-028-96
8-729-018-75
8-729-017-65
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA144EUA-T106
DTC114EUA-T106
2SJ278MY
2SK1764KY
< RESISTOR >
R101
R103
R104
R105
R106
1-216-295-00
1-216-049-91
1-216-073-00
1-216-065-91
1-216-133-00
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
0
1K
10K
4.7K
3.3M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R107
R109
R110
R111
R112
1-216-113-00
1-216-295-00
1-216-073-00
1-216-295-00
1-216-089-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
470K
0
10K
0
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R113
R115
R117
R120
R121
1-216-049-91
1-216-049-91
1-216-113-00
1-216-025-91
1-216-097-91
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
1K
1K
470K
100
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R123
R124
R125
R127
R131
1-216-033-00
1-216-025-91
1-216-025-91
1-216-025-91
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
220
100
100
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R132
R133
R134
R135
R136
1-216-097-91
1-216-117-00
1-216-049-91
1-216-061-00
1-216-049-91
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
100K
680K
1K
3.3K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R137
R140
R141
R142
R143
1-216-025-91
1-216-029-00
1-216-295-00
1-216-073-00
1-216-073-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
150
0
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R144
R146
R147
R148
R150
1-216-025-91
1-216-037-00
1-216-025-91
1-216-045-00
1-216-295-00
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
100
330
100
680
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R158
R159
R161
R162
R163
1-216-097-91
1-216-097-91
1-216-057-00
1-216-057-00
1-216-057-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R164
R165
R166
R167
R169
1-216-045-00
1-216-097-91
1-220-149-11
1-216-065-91
1-219-724-11
METAL CHIP
RES,CHIP
REGISTER
RES,CHIP
METAL CHIP
680
100K
2.2
4.7K
1
5%
5%
10%
5%
1%
1/10W
1/10W
1/2W
1/10W
1/4W
DG
Part No.
Description
R170
R171
R172
R173
R175
1-216-073-00
1-216-073-00
1-216-295-00
1-216-121-91
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
10K
10K
0
1M
3.3K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R176
R177
R178
R179
R180
1-216-295-00
1-216-061-00
1-216-295-00
1-216-089-91
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
0
3.3K
0
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R181
R182
R183
R184
R185
1-216-073-00
1-216-089-91
1-216-089-91
1-216-073-00
1-216-073-00
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
10K
47K
47K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R186
R187
R188
R189
R190
1-216-296-00
1-216-296-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
10K
10K
10K
5%
5%
5%
5%
5%
1/8W
1/8W
1/10W
1/10W
1/10W
R195
R196
R198
R199
R200
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R201
1-216-295-00 METAL CHIP
0
5%
1/10W
R202
1-216-295-00 METAL CHIP
0
5%
1/10W
R502
1-216-295-00 METAL CHIP
0
5%
1/10W
R504
1-216-295-00 METAL CHIP
0
5%
1/10W
************************************************************
A-3321-550-A DG BOARD, COMPLETE (US)
A-3321-571-A DG BOARD, COMPLETE (EXCEPT US)
*******************
*
*
< CAPACITOR >
C501
C502
C503
C504
C505
1-164-156-11
1-162-927-11
1-162-927-11
1-162-916-11
1-162-916-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100PF
100PF
12PF
12PF
C506
C507
C508
C510
C511
1-163-077-00
1-164-156-11
1-164-156-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100PF
100PF
C512
C513
C514
C515
C516
1-164-156-11
1-164-156-11
1-164-156-11
1-126-205-11
1-126-607-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
47uF
47uF
C517
C518
C519
C521
C522
1-164-156-11
1-164-156-11
1-126-205-11
1-126-603-11
1-126-603-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
C525
C526
C527
1-126-603-11 ELECT CHIP
1-126-205-11 ELECT CHIP
1-126-205-11 ELECT CHIP
– 115 –
5%
5%
5%
5%
10%
25V
50V
50V
50V
50V
5%
5%
25V
25V
25V
50V
50V
20%
20%
25V
25V
25V
6.3V
4V
0.1uF
0.1uF
47uF
4.7uF
4.7uF
20%
20%
20%
25V
25V
6.3V
35V
35V
4.7uF
47uF
47uF
20%
20%
20%
35V
6.3V
6.3V
DG
Ref. No.
Part No.
Description
Remark
C528
C529
1-164-156-11 CERAMIC CHIP
1-124-779-00 ELECT CHIP
0.1uF
10uF
C532
C533
C534
C535
C536
1-126-603-11
1-126-603-11
1-164-156-11
1-162-962-11
1-163-251-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
4.7uF
0.1uF
470PF
100PF
C537
C538
C542
C545
C547
1-162-959-11
1-162-959-11
1-164-156-11
1-164-156-11
1-126-205-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
330PF
330PF
0.1uF
0.1uF
47uF
C558
C561
C562
C563
C564
1-162-970-11
1-126-204-11
1-164-156-11
1-126-207-11
1-162-966-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01uF
47uF
0.1uF
33uF
0.0022uF
10%
20%
20%
10%
25V
16V
25V
4V
50V
C565
C566
C567
C568
C569
1-162-966-11
1-162-966-11
1-162-966-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
0.0022uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C572
C574
C576
C577
C578
1-162-970-11
1-109-994-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
2.2uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
25V
10V
50V
50V
50V
C579
C580
C581
C582
C583
1-162-964-11
1-162-964-11
1-162-964-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
50V
50V
50V
25V
25V
C585
C586
C587
C588
C589
1-162-970-11
1-162-970-11
1-107-823-11
1-163-059-00
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.47uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
16V
50V
25V
C590
C591
C592
C593
C594
1-164-156-11
1-164-156-11
1-109-994-11
1-162-915-11
1-162-915-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
2.2uF
10PF
10PF
10%
0.5PF
0.5PF
25V
25V
10V
50V
50V
20%
20%
20%
10%
5%
5%
5%
20%
< CONNECTOR >
CN501
CN502
* CN503
CN504
1-784-836-21
1-778-691-11
1-695-320-21
1-750-524-31
CONNECTOR (SMD) 29P
CONNECTOR, FFC/FPC 19P
PIN, CONNECTOR (1.5MM)(SMD) 2P
CONNECTOR, FFC/FPC (ZIF) 26P
25V
16V
35V
35V
25V
50V
50V
50V
50V
25V
25V
6.3V
Ref. No.
Part No.
8-719-914-43 DIODE DAN202K
8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
FB502
FB503
FB521
FB522
1-414-385-11
1-414-385-11
1-414-385-11
1-414-385-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
Remark
1-414-385-11 INDUCTOR, FERRITE BEAD
FB524
FB525
FB527
FB528
FB530
1-414-385-11
1-414-385-11
1-414-235-11
1-414-235-11
1-414-385-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB531
FB532
FB533
FB534
FB535
1-414-385-11
1-414-385-11
1-414-235-11
1-414-385-11
1-414-235-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB536
FB539
FB541
FB542
FB543
1-414-385-11
1-414-385-11
1-414-385-11
1-414-235-11
1-414-385-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB544
FB545
FB546
FB547
FB548
1-414-385-11
1-414-385-11
1-414-385-11
1-414-235-11
1-414-235-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB549
FB550
FB551
FB552
FB553
1-414-235-21
1-414-385-11
1-414-385-11
1-414-385-11
1-414-385-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB554
FB555
FB558
FB560
FB561
1-414-385-11
1-414-385-11
1-414-385-11
1-414-811-21
1-414-385-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB562
FB563
FB564
FB566
FB567
1-414-385-11
1-469-185-11
1-469-185-11
1-414-235-11
1-414-235-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB568
FB569
1-414-385-11 INDUCTOR, FERRITE BEAD
1-414-385-11 INDUCTOR, FERRITE BEAD
< IC >
IC501
IC502
IC503
IC504
IC505
8-759-444-93
8-759-494-80
8-759-040-83
8-759-444-93
8-759-566-19
IC506
IC507
8-759-096-87 IC TC7WU04FU(TE12R)
8-759-243-19 IC TC7SU04F
IC
IC
IC
IC
IC
RH5RL33AA-T1
RU8X12MF-0021
BA6287F
RH5RL33AA-T1
AK4518VF-E2
< JUMPER RESISTOR >
< DIODE >
D551
D552
Description
FB523
JC502
JC503
JC504
JC505
JC506
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
JC507
JC508
JC509
1-216-296-00 METAL CHIP
1-216-296-00 METAL CHIP
1-216-296-00 METAL CHIP
0
0
0
5%
5%
5%
1/8W
1/8W
1/8W
– 116 –
DG
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
JC513
JC514
1-216-296-00 METAL CHIP
1-216-296-00 METAL CHIP
0
0
5%
5%
1/8W
1/8W
R509
R510
1-216-857-11 METAL CHIP
1-216-833-11 METAL CHIP
1M
10K
5%
5%
1/16W
1/16W
JC515
JC516
JC517
JC520
JC521
1-216-296-00
1-216-295-00
1-216-296-00
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/10W
1/8W
1/10W
1/8W
R511
R512
R513
R514
R515
1-216-845-11
1-216-025-91
1-216-025-91
1-216-833-11
1-216-097-91
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
100K
100
100
10K
100K
5%
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/16W
1/10W
JC525
JC537
JC538
JC539
JC542
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/10W
1/16W
R516
R517
R518
R519
R520
1-216-851-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330K
10K
10K
10K
220K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
JC543
JC551
JC565
1-216-864-11 METAL CHIP
1-216-296-00 METAL CHIP
1-216-295-00 METAL CHIP
0
0
0
5%
5%
5%
1/16W
1/8W
1/10W
R521
R522
R523
R524
R525
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< COIL >
L501
L502
L503
L504
L505
1-414-398-11
1-414-398-11
1-414-398-11
1-414-398-11
1-414-398-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
R526
R527
R529
R531
R532
1-216-833-11
1-216-833-11
1-216-807-11
1-216-833-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
68
10K
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
L507
L508
L509
L510
L511
1-414-398-11
1-412-032-11
1-414-404-11
1-414-398-11
1-416-107-21
INDUCTOR
INDUCTOR CHIP
INDUCTOR
INDUCTOR
INDUCTOR
10uH
100uH
100uH
10uH
0uH
R533
R534
R536
R537
R541
1-216-821-11
1-216-821-11
1-216-845-11
1-216-845-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100K
100K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
L512
L513
L515
1-412-006-31 INDUCTOR CHIP 10uH
1-414-398-11 INDUCTOR
10uH
1-414-404-21 INDUCTOR CHIP 100uH
< TRANSISTOR >
R543
R544
R548
R551
R552
1-216-841-11
1-216-819-11
1-216-853-11
1-216-847-11
1-216-843-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
680
470K
150K
68K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Q501
Q502
Q503
Q504
Q507
8-729-031-43
8-729-402-84
8-729-027-46
8-729-101-07
8-729-402-84
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
IMD9A-T108
XN4601
DTC114YKA-T146
2SB798-DL
XN4601
R553
R554
R555
R556
R557
1-216-833-11
1-216-222-00
1-216-089-91
1-216-841-11
1-216-821-11
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
10K
10K
47K
47K
1K
5%
5%
5%
5%
5%
1/16W
1/8W
1/10W
1/16W
1/16W
Q509
Q510
Q511
Q520
Q521
8-729-027-46
8-729-027-56
8-729-019-72
8-729-027-46
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
DTC143TKA-T146
2SB1260
DTC114YKA-T146
DTC114YKA-T146
R558
R559
R560
R561
R562
1-216-214-00
1-216-821-11
1-216-821-11
1-216-821-11
1-216-829-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
1K
1K
4.7K
5%
5%
5%
5%
5%
1/8W
1/16W
1/16W
1/16W
1/16W
Q522
Q551
Q552
Q553
Q554
8-729-027-46
8-729-046-16
8-729-046-15
8-729-046-16
8-729-046-15
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
UMG5N-TR
UMA1N-TR
UMG5N-TR
UMA1N-TR
R565
R567
R571
R572
R573
1-216-817-11
1-216-841-11
1-216-097-91
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
470
47K
100K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/10W
1/10W
1/10W
R580
R581
R582
R583
R584
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R585
R586
R587
R588
R589
1-216-819-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
10K
10K
1K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< RESISTOR >
R501
R502
R503
R504
R505
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R506
R507
R508
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
100K
100K
100K
5%
5%
5%
1/16W
1/16W
1/16W
– 117 –
DG
Ref. No.
R590
FILTER
Part No.
FL
Description
1-216-841-11 METAL CHIP
Remark
47K
5%
1/16W
< VIBRATOR >
X501
1-760-174-11 VIBRATOR, CERAMIC (12MHz)
X502
1-760-872-11 VIBRATOR, CRYSTAL (32.768KHz)
X503
1-767-286-11 VIBRATOR, CRYSTAL (22.5792MHz)
************************************************************
1-671-517-11 FILTER BOARD
************
*
< CONNECTOR >
CN550
CN551
1-750-524-31 CONNECTOR, FFC/FPC (ZIF) 26P
1-750-524-31 CONNECTOR, FFC/FPC (ZIF) 26P
Ref. No.
Part No.
Description
C408
C409
C410
C411
C412
1-163-239-11
1-163-021-91
1-163-021-91
1-104-664-11
1-163-059-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
33PF
0.01uF
0.01uF
47uF
0.01uF
5%
10%
10%
20%
10%
50V
50V
50V
16V
50V
Remark
C413
C414
C416
C417
C418
1-163-021-91
1-164-004-11
1-163-104-00
1-163-104-00
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
30PF
30PF
10uF
10%
10%
5%
5%
20%
50V
25V
50V
50V
50V
C419
C420
C421
C422
C423
1-163-021-91
1-164-337-11
1-164-337-11
1-164-337-11
1-164-337-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
2.2uF
2.2uF
2.2uF
2.2uF
10%
50V
16V
16V
16V
16V
C424
1-164-337-11 CERAMIC CHIP
< FERRITE BEAD >
FB590
FB591
1-469-185-11 FERRITE
1-469-185-11 FERRITE
0UH
0UH
* CN404
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FL506
FL507
FL508
FL509
FL510
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FL511
FL512
FL513
FL514
FL515
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FL516
FL517
FL518
FL519
FL520
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
1-239-895-11
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FILTER, EMI (SMD)
FL521
FL522
1-239-895-11 FILTER, EMI (SMD)
1-239-895-11 FILTER, EMI (SMD)
1-569-306-11 SOCKET, CONNECTOR (L TYRE) 15P
< FLUORESCENT INDICATOR TUBE >
FL401
1-517-744-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC401
8-752-891-96 IC CXP82832-005Q
< JUMPER RESISTOR >
JC401
JC402
JC403
JC404
JC405
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/8W
1/8W
JC406
1-216-296-00 METAL CHIP
0
5%
1/8W
< TRANSISTOR >
Q404
Q405
Q406
8-729-402-19 TRANSISTOR XN6501
8-729-028-21 TRANSISTOR XN4502
8-729-024-33 TRANSISTOR XN1509-TX
< RESISTOR >
< JUMPER RESISTOR >
JC590 1-216-295-00 METAL CHIP
0
5%
1/10W
************************************************************
A-3323-029-A FL BOARD, COMPLETE (US)
A-3323-036-A FL BOARD, COMPLETE (EXCEPT US)
******************
3-019-671-01 HOLDER (FL)
*
*
16V
< CONNECTOR >
< FILTER >
FL501
FL502
FL503
FL504
FL505
2.2uF
R401
R439
R440
R441
R442
1-216-073-00
1-216-073-00
1-216-049-91
1-216-073-00
1-216-049-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
10K
10K
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R443
R444
R445
R446
R447
1-216-049-91
1-216-073-00
1-216-049-91
1-216-073-00
1-216-049-91
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
1K
10K
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R448
R449
R450
R451
R452
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R453
1-216-049-91 RES,CHIP
1K
5%
1/10W
< CAPACITOR >
C403
C404
C405
C406
C407
1-163-005-11
1-163-005-11
1-163-005-11
1-163-005-11
1-163-239-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
470PF
470PF
33PF
10%
10%
10%
10%
5%
50V
50V
50V
50V
50V
– 118 –
FL
Ref. No.
FM ANT
FRONT KEY
Part No.
Description
Remark
Ref. No.
Part No.
R454
R455
R456
R457
1-216-049-91
1-216-049-91
1-216-073-00
1-216-049-91
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
1K
1K
10K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
*
*
1-668-254-21 FM ANT BOARD (EXCEPT US)
1-668-254-31 FM ANT BOARD (US)
*************
Description
Remark
R458
R463
R464
R465
R466
1-216-009-00
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R467
R468
R469
R470
R471
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R472
R473
R474
R475
R476
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R477
R478
R479
R480
R481
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R482
R483
R484
R485
R486
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R487
R488
R489
R490
R491
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R492
R493
R494
R495
R496
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R497
R498
R499
R500
R501
1-216-089-91
1-216-089-91
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R502
R503
R504
R505
R506
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R507
R508
R509
R510
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< CONNECTOR >
* CN41
* CN41
1-580-154-11 PIN, CONNECTOR (PC BOARD) 2P
(EXCEPT US)
1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P (US)
< SWITCH >
< VIBRATOR >
X811
1-767-838-11 VIBRATOR, CERAMIC (6MHz)
************************************************************
S1
1-771-535-11 SWITCH, SLIDE (FM ANTENNA SELECTOR)
(EXCEPT US)
< TERMINAL >
TB40
1-536-833-31 TERMINAL BOARD (FM EXT ANTENNA) (US)
************************************************************
A-3321-539-A FRONT KEY BOARD, COMPLETE (US)
A-3321-557-A FRONT KEY BOARD, COMPLETE (EXCEPT US)
**************************
*
*
3-020-475-01 HOLDER (LED)
< CAPACITOR >
C401
C402
1-163-021-91 CERAMIC CHIP
1-109-994-11 CERAMIC CHIP
0.01uF
2.2uF
10%
10%
50V
10V
< CONNECTOR >
CN401
1-580-168-11 PIN, CONNECTOR (PC BOARD) 7P
< DIODE >
D401
D402
D403
D404
D405
8-719-071-33
8-719-071-33
8-719-071-33
8-719-071-33
8-719-071-33
LED
LED
LED
LED
LED
MBG3362X-TP-J434K (RADIO)
MBG3362X-TP-J434K (RADIO)
MBG3362X-TP-J434K (CD)
MBG3362X-TP-J434K (CD)
MBG3362X-TP-J434K (MD)
D406
8-719-071-33 LED MBG3362X-TP-J434K (MD)
< IC >
IC402
8-749-011-03 IC GP1U26X
< TRANSISTOR >
Q401
Q402
Q403
8-729-027-42 TRANSISTOR DTC113ZKA-T146
8-729-027-42 TRANSISTOR DTC113ZKA-T146
8-729-027-42 TRANSISTOR DTC113ZKA-T146
< RESISTOR >
R404
R405
R406
R407
R408
1-208-794-11
1-216-655-11
1-216-655-11
1-208-782-11
1-208-778-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
3.3K
1.5K
1.5K
1K
680
0.50%
0.5%
0.5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R409
R410
R411
R412
R413
1-208-778-11
1-208-774-11
1-208-774-11
1-216-029-00
1-216-029-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
680
470
470
150
150
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
– 119 –
FRONT KEY
Ref. No.
R414
R458
R459
R460
R461
HP
LEFT KEY
Part No.
Description
1-216-029-00
1-216-029-00
1-216-029-00
1-216-029-00
1-216-049-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
150
150
150
150
1K
LINE IN
5%
5%
5%
5%
5%
Remark
Ref. No.
1/10W
1/10W
1/10W
1/10W
1/10W
R275
1-216-013-00 METAL CHIP
33
5%
1/10W
************************************************************
Part No.
Description
Remark
1-668-243-21 LEFT KEY BOARD (EXCEPT US)
1-668-243-31 LEFT KEY BOARD (US)
**************
*
*
< SWITCH >
< CONNECTOR >
S801
S802
S803
S804
S805
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEY BOARD (MD p )
SWITCH, KEY BOARD (CD p )
SWITCH, KEY BOARD (MD ^ )
SWITCH, KEY BOARD (CD ^ )
SWITCH, KEY BOARD (RADIO, BAND)
CN406
< RESISTOR >
S806
1-692-014-11 SWITCH, KEY BOARD (MD EJECT)
S807
1-692-014-11 SWITCH, KEY BOARD (CD OPEN/CLOSE)
S808
1-692-014-11 SWITCH, KEY BOARD (LINE)
S809
1-692-014-11 SWITCH, KEY BOARD (REC)
************************************************************
1-668-250-21 HP BOARD (EXCEPT US)
1-668-250-31 HP BOARD (US)
*********
*
*
1-163-009-11 CERAMIC CHIP
0.001uF
C371
1-163-009-11 CERAMIC CHIP
0.001uF
C372
1-163-009-11 CERAMIC CHIP
0.001uF
C373
1-163-009-11 CERAMIC CHIP
0.001uF
C374
1-163-009-11 CERAMIC CHIP
0.001uF
C375
1-163-009-11 CERAMIC CHIP
0.001uF
R424
R425
R426
R427
R428
1-216-655-11
1-216-655-11
1-208-782-11
1-208-778-11
1-208-778-11
R429
R430
1-208-774-11 RES,CHIP
1-208-774-11 RES,CHIP
10%
50V
(EXCEPT US)
10%
50V
(EXCEPT US)
10%
50V
(US)
10%
50V
(US)
10%
50V
(US)
10%
50V
(US)
S813
S814
S815
S816
S817
0.5%
0.5%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
470
470
0.50% 1/10W
0.50% 1/10W
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEY BOARD (POWER)
SWITCH, KEY BOARD (DISC ALL)
SWITCH, KEY BOARD (TO TOP)
SWITCH, KEY BOARD (TO END)
SWITCH, KEY BOARD (SLEEP)
1-668-249-21 LINE IN BOARD (EXCEPT US)
1-668-249-31 LINE IN BOARD (US)
*************
*
*
< CAPACITOR >
1-580-166-21 PIN, CONNECTOR (PC BOARD) 5P
C392
< JACK >
J371
J372
1.5K
1.5K
1K
680
680
S818
1-692-014-11 SWITCH, KEY BOARD (STAND BY)
S819
1-692-014-11 SWITCH, KEY BOARD (TIMER)
S820
1-692-014-11 SWITCH, KEY BOARD (CLOCK)
************************************************************
< CONNECTOR >
* CN371
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
< SWITCH >
< CAPACITOR >
C370
1-695-105-11 PIN, CONNECTOR (PC BOARD) 3P
1-163-009-11 CERAMIC CHIP
0.001uF
10%
50V
< CONNECTOR >
1-566-891-21 JACK ( • 2 )
1-566-891-21 JACK ( • • 2 )
* CN331
1-695-112-11 PIN, CONNECTOR (PC BOARD) 10P
< FERRITE BEAD >
< INDUCTOR >
L171
L172
L271
L272
L371
1-410-503-11
1-410-503-11
1-410-503-11
1-410-503-11
1-410-503-11
INDUCTOR, MICRO
INDUCTOR, MICRO
INDUCTOR, MICRO
INDUCTOR, MICRO
INDUCTOR, MICRO
FB190
FB290
FB390
3.3uH
3.3uH
3.3uH
3.3uH
3.3uH
1-500-445-21 INDUCTOR, FERRITE BEAD (US)
1-500-445-21 INDUCTOR, FERRITE BEAD (US)
1-500-445-21 INDUCTOR, FERRITE BEAD (US)
< JACK >
J391
1-566-891-21 JACK (LINE IN)
< TRANSISTOR >
< INDUCTOR >
Q172
Q173
Q272
Q273
8-729-920-31
8-729-920-31
8-729-920-31
8-729-920-31
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC343TK
DTC343TK
DTC343TK
DTC343TK
< RESISTOR >
R174
R175
R274
1-216-013-00 METAL CHIP
1-216-013-00 METAL CHIP
1-216-013-00 METAL CHIP
33
33
33
5%
5%
5%
L190
1-410-503-61 INDUCTOR, MICRO
L290
1-410-503-61 INDUCTOR, MICRO
L390
1-410-503-61 INDUCTOR, MICRO
1/10W
1/10W
1/10W
< TRANSISTOR >
Q192
– 120 –
8-729-920-31 TRANSISTOR DTC343TK
3.3uH
(EXCEPT US)
3.3uH
(EXCEPT US)
3.3uH
(EXCEPT US)
LINE IN
Ref. No.
Q292
Q392
Q399
Part No.
Description
Remark
8-729-920-31 TRANSISTOR DTC343TK
8-729-027-45 TRANSISTOR DTC114WKA-T146
8-729-027-26 TRANSISTOR DTA114YKA-T146
< RESISTOR >
R197
R198
R297
R298
R391
1-216-089-91
1-216-089-91
1-216-089-91
1-216-089-91
1-216-025-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
47K
47K
47K
47K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S891
1-554-088-00 SWITCH, KEY BOARD (RESET)
************************************************************
1-667-045-11 LOADING BOARD
**************
*
< CAPACITOR >
C790
1-104-664-11 ELECT
47uF
20%
25V
< CONNECTOR >
* CN790
1-580-166-11 PIN, CONNECTOR (PC BOARD) 5P
< DIODE >
D790
8-719-970-02 DIODE 1SR139-400
< IC >
IC790
8-759-501-73 IC BA6418N
< COIL >
L790
1-412-852-11 INDUCTOR
47uH
< RESISTOR >
R790
1-249-425-11 CARBON
4.7K
5%
1/4W
< SWITCH >
S790
1-762-951-11 SWITCH, PUSH (CLOSE)
S791
1-762-951-11 SWITCH, PUSH (OPEN)
************************************************************
A-3321-544-A MAIN BOARD, COMPLETE (US)
A-3321-565-A MAIN BOARD, COMPLETE (EXCEPT US)
*********************
*
*
7-685-646-79 SCREW +BVTP
3X8 TYPE2 N-S
< CAPACITOR >
C101
C102
C103
C106
C110
1-126-959-11
1-126-963-11
1-163-251-11
1-126-963-11
1-126-963-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
0.47uF
4.7uF
100PF
4.7uF
4.7uF
20%
20%
5%
20%
20%
50V
50V
50V
50V
50V
C111
C116
C117
C120
C121
1-126-963-11
1-126-963-11
1-130-480-00
1-136-164-00
1-136-164-00
ELECT
ELECT
MYLAR
FILM
FILM
4.7uF
4.7uF
0.0056uF
0.082uF
0.082uF
20%
20%
5%
5%
5%
50V
50V
50V
50V
50V
Ref. No.
LOADING
MAIN
Part No.
Description
C122
C123
C124
C125
C126
1-136-165-00
1-136-165-00
1-126-960-11
1-162-927-11
1-124-994-11
FILM
FILM
ELECT
CERAMIC CHIP
ELECT
0.1uF
0.1uF
1uF
100PF
100uF
5%
5%
20%
5%
20%
50V
50V
50V
50V
10V
C127
C128
C129
C130
C131
1-130-474-00
1-106-359-00
1-162-965-11
1-163-017-00
1-104-665-11
MYLAR
MYLAR
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.0018uF
4700PF
0.0015uF
0.0047uF
100uF
5%
5%
10%
5%
20%
50V
200V
50V
50V
10V
C132
C133
C201
C202
C203
1-136-165-00
1-126-934-11
1-126-959-11
1-126-963-11
1-163-251-11
FILM
ELECT
ELECT
ELECT
CERAMIC CHIP
0.1uF
220uF
0.47uF
4.7uF
100PF
5%
20%
20%
20%
5%
50V
10V
50V
50V
50V
C206
C210
C211
C216
C217
1-126-963-11
1-126-963-11
1-126-963-11
1-126-963-11
1-130-480-00
ELECT
ELECT
ELECT
ELECT
MYLAR
4.7uF
4.7uF
4.7uF
4.7uF
0.0056uF
20%
20%
20%
20%
5%
50V
50V
50V
50V
50V
C220
C221
C222
C223
C224
1-136-164-00
1-136-164-00
1-136-165-00
1-136-165-00
1-126-960-11
FILM
FILM
FILM
FILM
ELECT
0.082uF
0.082uF
0.1uF
0.1uF
1uF
5%
5%
5%
5%
20%
50V
50V
50V
50V
50V
C225
C226
C227
C228
C229
1-162-927-11
1-124-994-11
1-130-474-00
1-106-359-00
1-162-965-11
CERAMIC CHIP
ELECT
MYLAR
MYLAR
CERAMIC CHIP
100PF
100uF
0.0018uF
4700PF
0.0015uF
5%
20%
5%
5%
10%
50V
10V
50V
200V
50V
C230
C231
C232
C233
C301
1-163-017-00
1-104-665-11
1-136-165-00
1-126-934-11
1-124-994-11
CERAMIC CHIP
ELECT
FILM
ELECT
ELECT
0.0047uF
100uF
0.1uF
220uF
100uF
5%
20%
5%
20%
20%
50V
10V
50V
10V
10V
C302
C303
C304
C307
C308
1-126-934-11
1-126-964-11
1-104-665-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
220uF
10uF
100uF
10uF
10uF
20%
20%
20%
20%
20%
10V
50V
10V
50V
50V
C309
C311
C701
C702
C703
1-104-665-11
1-126-964-11
1-162-968-11
1-162-970-11
1-162-969-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
10uF
0.0047uF
0.01uF
0.0068uF
20%
20%
10%
10%
10%
10V
50V
50V
25V
25V
C704
C705
C706
C707
C708
1-163-809-11
1-163-021-91
1-124-994-11
1-164-227-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.01uF
100uF
0.022uF
0.1uF
10%
10%
20%
10%
10%
25V
50V
10V
25V
25V
C709
C710
C711
C712
C713
1-162-968-11
1-164-004-11
1-163-113-00
1-163-009-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.1uF
68PF
0.001uF
0.1uF
10%
10%
5%
10%
10%
50V
25V
50V
50V
25V
C714
C715
C716
1-164-004-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
0.1uF
1uF
0.1uF
10%
10%
10%
25V
10V
25V
– 121 –
Remark
MAIN
Ref. No.
Part No.
Description
Remark
C717
C718
1-162-965-11 CERAMIC CHIP
1-163-021-91 CERAMIC CHIP
0.0015uF 10%
0.01uF
10%
50V
50V
C719
C720
C721
C722
C723
1-162-970-11
1-135-181-21
1-104-664-11
1-163-017-00
1-164-677-11
CERAMIC CHIP
TANTALUM CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
4.7uF
47uF
0.0047uF
0.033uF
10%
20%
20%
5%
10%
25V
6.3V
16V
50V
16V
C724
C725
C726
C727
C728
1-164-677-11
1-162-970-11
1-104-509-11
1-162-969-11
1-163-021-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.033uF
0.01uF
0.018uF
0.0068uF
0.01uF
10%
10%
10%
10%
10%
16V
25V
16V
25V
50V
C729
C730
C731
C732
C733
1-162-927-11
1-162-968-11
1-124-994-11
1-164-677-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100PF
0.0047uF
100uF
0.033uF
2.2uF
5%
10%
20%
10%
50V
50V
10V
16V
16V
C734
C735
C736
C737
C739
1-163-033-91
1-162-923-11
1-162-970-11
1-124-994-11
1-124-994-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.022uF
47PF
0.01uF
100uF
100uF
5%
10%
20%
20%
50V
50V
25V
10V
10V
C741
C742
C743
C744
C745
1-163-009-11
1-163-251-11
1-163-251-11
1-163-251-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100PF
100PF
100PF
0.022uF
10%
5%
5%
5%
10%
50V
50V
50V
50V
25V
C747
C748
C749
C750
C751
1-126-925-11
1-104-665-11
1-162-962-11
1-124-994-11
1-162-964-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
470uF
100uF
470PF
100uF
0.001uF
20%
20%
10%
20%
10%
10V
10V
50V
10V
50V
C752
C753
C754
C755
C756
1-162-964-11
1-162-970-11
1-162-927-11
1-162-970-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.01uF
100PF
0.01uF
470PF
10%
10%
5%
10%
10%
50V
25V
50V
25V
50V
C757
C758
C759
C760
C762
1-162-957-11
1-162-970-11
1-104-665-11
1-162-970-11
1-163-021-91
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
220PF
0.01uF
100uF
0.01uF
0.01uF
5%
10%
20%
10%
10%
50V
25V
10V
25V
50V
C763
C764
C765
C766
C767
1-107-823-11
1-163-227-11
1-163-021-91
1-163-227-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
10PF
0.01uF
10PF
470PF
10%
0.5PF
10%
0.5PF
10%
16V
50V
50V
50V
50V
C768
C770
C771
C772
C773
1-162-957-11
1-162-970-11
1-115-467-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.01uF
0.22uF
0.01uF
0.01uF
5%
10%
10%
10%
10%
50V
25V
10V
25V
25V
C775
C777
C778
C779
C780
1-162-970-11
1-126-963-11
1-126-963-11
1-164-489-11
1-162-970-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
4.7uF
4.7uF
0.22uF
0.01uF
10%
20%
20%
10%
10%
25V
50V
50V
16V
25V
Ref. No.
Part No.
Description
C781
C782
C783
C784
C786
1-110-501-11
1-164-004-11
1-164-004-11
1-127-508-00
1-127-508-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.33uF
0.1uF
0.1uF
2.2uF
2.2uF
10%
10%
10%
20%
20%
16V
25V
25V
25V
25V
C787
C788
C789
C801
C802
1-164-004-11
1-164-004-11
1-163-009-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
25V
25V
50V
50V
50V
C803
C804
C805
C806
C807
1-162-927-11
1-162-927-11
1-162-964-11
1-162-964-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
0.001uF
0.001uF
0.01uF
5%
5%
10%
10%
10%
50V
50V
50V
50V
25V
C808
C809
C810
C811
C812
1-162-964-11
1-163-017-00
1-162-968-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0047uF
0.0047uF
0.001uF
0.1uF
10%
5%
10%
10%
10%
50V
50V
50V
50V
16V
C813
C814
C815
C816
C817
1-162-921-11
1-162-921-11
1-163-037-11
1-162-970-11
1-163-237-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
33PF
33PF
0.022uF
0.01uF
27PF
5%
5%
10%
10%
5%
50V
50V
25V
25V
50V
C818
C819
C820
C821
C822
1-162-921-11
1-162-919-11
1-107-826-11
1-163-234-11
1-104-664-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
33PF
22PF
0.1uF
20PF
47uF
5%
5%
10%
5%
20%
50V
50V
16V
50V
16V
C823
C824
C825
C826
C827
1-162-970-11
1-104-665-11
1-104-664-11
1-162-961-11
1-162-927-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
100uF
47uF
330PF
100PF
10%
20%
20%
10%
5%
25V
10V
16V
50V
50V
C829
C830
C831
C832
C833
1-162-961-11
1-162-964-11
1-162-970-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330PF
0.001uF
0.01uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
25V
50V
50V
C834
C835
C836
C837
C838
1-162-964-11
1-162-964-11
1-162-964-11
1-163-059-91
1-127-508-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
0.001uF
0.001uF
0.01uF
2.2uF
10%
10%
10%
10%
20%
50V
50V
50V
50V
25V
C839
C840
C841
C842
C843
1-162-970-11
1-163-059-91
1-162-964-11
1-162-964-11
1-107-823-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.001uF
0.001uF
0.47uF
10%
10%
10%
10%
10%
25V
50V
50V
50V
16V
C844
C845
C847
C850
C851
1-107-826-11
1-162-964-11
1-162-961-11
1-163-009-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.001uF
330PF
0.001uF
2.2uF
10%
10%
10%
10%
16V
50V
50V
50V
16V
C852
C853
C854
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10%
10%
10%
50V
50V
50V
– 122 –
Remark
MAIN
Ref. No.
Part No.
Description
Remark
C855
C856
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
10%
10%
50V
50V
C857
C858
C859
C860
C861
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C866
C867
C871
C880
C881
1-126-960-11
1-126-960-11
1-126-233-11
1-163-009-11
1-163-009-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
22uF
0.001uF
0.001uF
20%
20%
20%
10%
10%
50V
50V
50V
50V
50V
C901
C902
C903
C904
C905
1-126-044-11
1-164-004-11
1-124-994-11
1-163-021-91
1-125-784-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
1uF
0.1uF
100uF
0.01uF
15000uF
20%
10%
20%
10%
20%
50V
25V
10V
50V
25V
C906
C907
C908
C909
C910
1-126-934-11
1-104-665-11
1-163-021-91
1-126-964-11
1-127-508-00
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
220uF
100uF
0.01uF
10uF
2.2uF
20%
20%
10%
20%
20%
10V
10V
50V
50V
25V
C911
C912
C913
C914
C915
1-110-501-11
1-104-905-11
1-126-964-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
CAPACITOR
ELECT
ELECT
ELECT
0.33uF
0.22F
10uF
10uF
10uF
10%
20%
20%
20%
16V
5.5V
50V
50V
50V
C916
C917
C918
C919
C920
1-104-664-11
1-127-508-00
1-127-508-00
1-126-964-11
1-163-021-91
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
47uF
2.2uF
2.2uF
10uF
0.01uF
20%
20%
20%
20%
10%
10V
25V
25V
50V
50V
C921
C922
C923
C924
C925
1-163-021-91
1-126-964-11
1-162-970-11
1-126-968-11
1-163-021-91
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
10uF
0.01uF
100uF
0.01uF
10%
20%
10%
20%
10%
50V
50V
25V
50V
50V
C926
C927
C928
1-126-964-11 ELECT
1-127-508-00 ELECT
1-113-981-11 TANTAL. CHIP
10uF
2.2uF
22uF
20%
20%
20%
50V
25V
20V
< CONNECTOR >
CN701
* CN703
CN801
CN802
CN803
1-569-324-11
1-580-154-11
1-569-321-11
1-573-489-11
1-506-987-11
SOCKET, CONNECTOR 21P
PIN, CONNECTOR (PC BOARD) 2P
SOCKET, CONNECTOR 15P
PIN, CONNECTOR (PC BOARD) 11P
PIN, CONNECTOR (PC BOARD) 5P
CN804
CN805
CN806
* CN807
* CN808
1-506-987-11
1-569-326-11
1-568-443-11
1-691-581-11
1-573-489-21
PIN, CONNECTOR (PC BOARD) 5P
SOCKET, CONNECTOR 26P
SOCKET, CONNECTOR 13P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 11P
* CN809
* CN810
1-580-158-11 PIN, CONNECTOR (PC BOARD) 6P
1-580-158-11 PIN, CONNECTOR (PC BOARD) 6P
< DIODE >
D301
8-719-801-78 DIODE 1SS184
Ref. No.
Part No.
Description
D302
D303
D306
D711
8-719-404-49
8-719-800-76
8-719-404-49
8-719-404-49
DIODE
DIODE
DIODE
DIODE
MA111
1SS226
MA111
MA111
Remark
D712
D901
D902
D903
D904
8-719-404-49
8-719-988-62
8-719-421-27
8-719-018-12
8-719-422-67
DIODE
DIODE
DIODE
DIODE
DIODE
MA111
1SS355
MA728
MA8330
MA8062-H
D905
D906
D907
D910
8-719-404-49
8-719-421-27
8-719-421-27
8-719-404-49
DIODE
DIODE
DIODE
DIODE
MA111
MA728
MA728
MA111
< FERRITE BEAD >
FB301
FB302
FB303
FB304
FB305
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB306
FB307
FB308
FB309
FB310
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB311
FB312
FB313
FB314
FB315
1-414-385-11
1-414-235-11
1-414-385-11
1-414-385-11
1-414-235-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
FB316
FB318
FB320
FB321
FB322
1-414-235-11
1-414-235-11
1-216-295-00
1-216-295-00
1-216-295-00
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
METAL CHIP
0
METAL CHIP
0
METAL CHIP
0
5%
5%
5%
1/10W
1/10W
1/10W
FB323
FB324
FB325
FB326
FB327
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
FB328
FB329
FB330
1-216-295-00 METAL CHIP
1-216-295-00 METAL CHIP
1-216-295-00 METAL CHIP
0
0
0
5%
5%
5%
1/10W
1/10W
1/10W
< IC >
IC101
IC201
IC301
IC302
IC701
8-759-636-55
8-759-636-55
8-759-567-92
8-759-701-02
8-752-082-14
IC
IC
IC
IC
IC
M5218AFP
M5218AFP
TDA7439DS013TR
NJM2073M
CXA1992BR
IC702
IC703
IC704
IC801
IC802
8-759-473-42
8-752-384-13
8-759-476-21
8-752-900-67
8-759-445-91
IC
IC
IC
IC
IC
BA6898FP
CXD2589Q
BA05SFP-E2
CXP84648-037Q
RN5VT28AA-TL
IC803
IC804
IC901
8-759-398-68 IC S-29330AFJ-TB
8-759-233-66 IC TC74HCT04AF
8-759-463-93 IC L88MS06T-FA-TL
– 123 –
MAIN
Ref. No.
Part No.
Description
Remark
IC902
IC903
8-759-290-19 IC BA3960
8-759-494-77 IC RH5RL58AA-T1
IC904
IC905
8-759-442-54 IC RH5RL50AA-T1
8-759-938-15 IC BA178M05
< JUMPER RESISTOR >
JC301
JC701
JC702
JC703
JC704
1-216-864-11
1-216-295-00
1-216-864-11
1-216-295-00
1-216-296-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/10W
1/8W
JC705
JC802
JC803
JC805
1-216-296-00
1-216-295-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
(US)
JC806
1-216-295-00 METAL CHIP
0
5%
JC807
JC809
JC850
JC851
1-216-295-00
1-216-296-00
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
5%
5%
5%
5%
1/10W
(EXCEPT US)
1/10W
1/8W
1/10W
1/10W
JC852
JC860
1-216-295-00 METAL CHIP
1-216-296-00 METAL CHIP
0
0
5%
5%
Ref. No.
Part No.
Description
Q803
Q902
Q903
Q905
Q909
8-729-120-28
8-729-027-58
8-729-402-84
8-729-031-43
8-729-031-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Remark
Q910
8-729-019-72 TRANSISTOR 2SB1260
2SC1623-L5L6
DTC143ZKA-T146
XN4601
IMD9A-T108
IMD9A-T108
< RESISTOR >
R101
R103
R104
R105
R106
1-218-758-11
1-216-669-11
1-216-665-11
1-216-683-11
1-218-776-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
180K
5.6K
3.9K
22K
1M
5%
0.5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R107
R108
R110
R111
R112
1-216-675-11
1-216-821-11
1-216-655-11
1-216-655-11
1-216-627-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1.5K
1.5K
100
0.5%
5%
0.5%
0.5%
0.5%
1/10W
1/16W
1/10W
1/10W
1/10W
R113
R114
R115
R116
R117
1-216-809-11
1-216-829-11
1-216-298-00
1-216-651-11
1-216-025-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
100
4.7K
2.2
1K
100
5%
5%
5%
0.5%
5%
1/16W
1/16W
1/10W
1/10W
1/10W
R119
R201
R203
R204
R205
1-216-821-11
1-218-758-11
1-216-669-11
1-216-665-11
1-216-683-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
180K
5.6K
3.9K
22K
5%
5%
0.5%
0.5%
0.5%
1/16W
1/10W
1/10W
1/10W
1/10W
R206
R207
R208
R210
R211
1-218-776-11
1-216-675-11
1-216-821-11
1-216-655-11
1-216-655-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
10K
1K
1.5K
1.5K
5%
0.5%
5%
0.5%
0.5%
1/10W
1/10W
1/16W
1/10W
1/10W
R212
R213
R214
R215
R216
1-216-627-11
1-216-809-11
1-216-829-11
1-216-298-00
1-216-651-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
4.7K
2.2
1K
0.5%
5%
5%
5%
0.5%
1/10W
1/16W
1/16W
1/10W
1/10W
< TRANSISTOR >
R217
R219
R301
R302
R303
1-216-025-91
1-216-821-11
1-216-015-00
1-216-615-11
1-216-675-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
39
33
10K
5%
5%
5%
0.5%
0.5%
1/10W
1/16W
1/10W
1/10W
1/10W
1/10W
1/8W
< COIL >
L101
L102
L103
L104
L105
1-410-999-11
1-410-999-11
1-410-999-11
1-410-999-11
1-410-999-11
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
3.3uH
3.3uH
3.3uH
3.3uH
3.3uH
L106
L201
L202
L203
L204
1-410-999-11
1-410-999-11
1-410-999-11
1-410-999-11
1-410-999-11
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
3.3uH
3.3uH
3.3uH
3.3uH
3.3uH
L205
L206
L701
L801
L802
1-410-999-11
1-410-999-11
1-216-057-00
1-216-295-00
1-216-295-00
INDUCTOR CHIP
INDUCTOR CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3uH
3.3uH
2.2K
0
0
5%
5%
5%
1/10W
1/10W
1/10W
Q102
Q103
Q202
Q203
Q301
8-729-120-28
8-729-920-31
8-729-120-28
8-729-920-31
8-729-031-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
DTC343TK
2SC1623-L5L6
DTC343TK
IMD9A-T108
R304
R305
R306
R308
R309
1-216-675-11
1-216-627-11
1-216-017-91
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
10K
100
47
1K
47K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/16W
1/16W
Q303
Q304
Q305
Q701
Q702
8-729-031-43
8-729-901-46
8-729-027-46
8-729-101-07
8-729-027-62
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
IMD9A-T108
DTA114YK
DTC114YKA-T146
2SB798-DL
DTC144WKA-T146
R310
R311
R315
R701
R702
1-216-821-11
1-216-089-91
1-216-825-11
1-216-849-11
1-216-864-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
2.2K
220K
0
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
Q703
Q704
Q705
Q801
Q802
8-729-901-46
8-729-027-56
8-729-027-56
8-729-027-46
8-729-024-33
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114YK
DTC143TKA-T146
DTC143TKA-T146
DTC114YKA-T146
XN1509-TX
R703
R704
R705
R706
R707
1-216-847-11
1-216-841-11
1-216-841-11
1-216-847-11
1-216-847-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150K
47K
47K
150K
150K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
– 124 –
MAIN
Ref. No.
Part No.
Description
R708
R709
R710
R712
R713
1-216-847-11
1-216-121-91
1-216-109-00
1-216-841-11
1-216-831-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150K
1M
330K
47K
6.8K
5%
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/16W
1/16W
Remark
R714
R715
R716
R717
R718
1-216-836-11
1-216-061-00
1-216-841-11
1-216-857-11
1-216-855-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
18K
3.3K
47K
1M
680K
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
R719
R720
R721
R722
R723
1-216-001-00
1-216-827-11
1-216-829-11
1-216-827-11
1-216-831-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
3.3K
4.7K
3.3K
6.8K
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/16W
R724
R725
R726
R727
R728
1-216-847-11
1-216-851-11
1-218-912-11
1-216-847-11
1-216-847-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
150K
330K
510K
150K
150K
5%
5%
0.50%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R729
R730
R731
R732
R733
1-216-834-11
1-216-849-11
1-216-847-11
1-216-841-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
12K
220K
150K
47K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R734
R735
R736
R737
R738
1-216-839-11
1-216-833-11
1-216-833-11
1-216-839-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
10K
10K
33K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R739
R740
R741
R742
R743
1-216-837-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R744
R745
R746
R747
R748
1-216-864-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-069-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
1K
1K
6.8K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/10W
R749
R750
R751
R752
R753
1-216-833-11
1-216-833-11
1-216-833-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
47K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R754
R755
R756
R757
R758
1-216-821-11
1-216-821-11
1-216-821-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
0
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R759
R760
R761
R762
R763
1-216-821-11
1-216-864-11
1-216-864-11
1-216-089-91
1-216-089-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
1K
0
0
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/10W
R764
R765
R766
1-216-651-11 METAL CHIP
1-216-061-00 METAL CHIP
1-216-821-11 METAL CHIP
1K
3.3K
1K
0.5%
5%
5%
1/10W
1/10W
1/16W
Ref. No.
Part No.
Description
Remark
R767
R768
1-216-833-11 METAL CHIP
1-216-857-11 METAL CHIP
10K
1M
5%
5%
1/16W
1/16W
R769
R770
R771
R772
R773
1-216-651-11
1-216-833-11
1-216-849-11
1-216-837-11
1-216-295-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
220K
22K
0
0.5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/10W
R774
R775
R776
R781
R782
1-216-663-11
1-216-295-00
1-216-663-11
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
0
3.3K
10K
10K
0.5%
5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R801
R802
R803
R804
R805
1-216-097-91
1-216-853-11
1-216-829-11
1-216-853-11
1-216-073-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
470K
4.7K
470K
10K
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/10W
R806
R807
R808
R814
R815
1-216-073-00
1-216-073-00
1-216-073-00
1-216-041-00
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
470
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/16W
R816
R819
R820
R823
R824
1-216-833-11
1-216-836-11
1-216-836-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
18K
18K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R833
R835
R838
R840
R842
1-216-049-91
1-216-821-11
1-216-851-11
1-216-809-11
1-216-821-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
330K
100
1K
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/16W
R850
R851
R867
R868
R869
1-216-833-11
1-216-815-11
1-216-833-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
330
10K
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R870
R871
R875
R879
R880
1-216-829-11
1-216-841-11
1-216-841-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
47K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R881
R882
R883
R884
R885
1-216-841-11
1-216-841-11
1-216-833-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
10K
10K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R886
R901
R902
R903
R904
1-216-841-11
1-216-089-91
1-216-113-00
1-216-073-00
1-216-061-00
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
470K
10K
3.3K
5%
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/10W
1/10W
R905
R906
R907
R908
R909
1-216-069-00
1-216-053-00
1-216-057-00
1-216-821-11
1-216-639-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.8K
1.5K
2.2K
1K
330
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/16W
1/10W
– 125 –
MAIN
Ref. No.
PICK-UP RELAY
RELAY
RIGHT KEY
SW
Part No.
Description
Remark
Ref. No.
Part No.
R910
R911
R912
R913
R914
1-216-025-91
1-216-061-00
1-216-061-00
1-216-109-00
1-216-226-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
100
3.3K
3.3K
330K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
*
*
1-668-246-21 RIGHT KEY BOARD (EXCEPT US)
1-668-246-31 RIGHT KEY BOARD (US)
****************
R915
R916
R917
R918
R919
1-216-809-11
1-216-843-11
1-216-837-11
1-216-845-11
1-216-053-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
68K
22K
100K
1.5K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/10W
R920
R924
R926
R927
R928
1-216-109-00
1-216-683-11
1-216-845-11
1-216-655-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330K
22K
100K
1.5K
47K
5%
0.5%
5%
0.5%
5%
1/10W
1/10W
1/16W
1/10W
1/16W
1-236-908-11
1-233-412-11
1-233-412-11
1-236-908-11
1-233-412-11
RES, CHIP NETWORK 10K
RES, CHIP NETWORK 1K
RES, CHIP NETWORK 1K
RES, CHIP NETWORK 10K
RES, CHIP NETWORK 1K
RB806
RB807
RB808
RB809
RB810
1-236-908-11
1-233-412-11
1-233-412-11
1-236-908-11
1-236-908-11
RES, CHIP NETWORK 10K
RES, CHIP NETWORK 1K
RES, CHIP NETWORK 1K
RES, CHIP NETWORK 10K
RES, CHIP NETWORK 10K
RB811
RB812
RB813
RB814
1-233-412-11
1-233-412-11
1-233-577-11
1-233-412-11
RES, CHIP NETWORK 1K
RES, CHIP NETWORK 1K
RES, CHIP NETWORK 470
RES, CHIP NETWORK 1K
Remark
< CAPACITOR >
C419
C420
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
0.1uF
0.1uF
10%
10%
25V
25V
< CONNECTOR >
* CN402
* CN405
CN407
1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P
1-580-166-11 PIN, CONNECTOR (PC BOARD) 5P
1-695-105-11 PIN, CONNECTOR (PC BOARD) 3P
< RESISTOR >
< COMPOSITION CIRCUIT BLOCK >
RB801
RB802
RB803
RB804
RB805
Description
R415
R416
R417
R418
R419
1-208-782-11
1-208-778-11
1-208-778-11
1-208-774-11
1-208-774-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
680
680
470
470
0.50%
0.50%
0.50%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R421
R422
R423
R431
R432
1-208-806-11
1-208-798-11
1-208-794-11
1-216-033-00
1-216-033-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
10K
4.7K
3.3K
220
220
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
< VIBRATOR >
X701
1-767-226-11 VIBRATOR, CRYSTAL (16.9344MHz)
X801
1-767-697-11 VIBRATOR, CRYSTAL (32.768kHz)
X802
1-767-839-11 VIBRATOR, CERAMIC (5MHz)
************************************************************
S401
S821
S822
S823
S825
1-771-214-11
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, ROTARY (PRESET,=AMS+)
SWITCH, KEY BOARD (CANSEL)
SWITCH, KEY BOARD (EDIT)
SWITCH, KEY BOARD (ENTER)
SWITCH, KEY BOARD (TUNE-,0,ı)
S826
S827
S828
S829
S830
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEY BOARD (TUNE+,),∫)
SWITCH, KEY BOARD (BASS/TREBLE)
SWITCH, KEY BOARD (DISPLAY)
SWITCH, KEY BOARD (VOLUME+)
SWITCH, KEY BOARD (VOLUME-)
************************************************************
1-667-046-11 PICK-UP RELAY BOARD
*******************
*
1-661-774-11 SW BOARD
*********
*
< CONNECTOR >
< CONNECTOR >
CN702
CN703
CN704
CN706
CN707
1-565-874-31
1-565-874-11
1-565-874-11
1-784-213-11
1-569-309-11
PIN, CONNECTOR (PC BOARD) 2P
PIN, CONNECTOR (PC BOARD) 2P
PIN, CONNECTOR (PC BOARD) 2P
CONNECTOR, FFC/FPC 14P
SOCKET, CONNECTOR (L TYPE) 21P
CN601
CN602
CN603
1-770-698-11 CONNECTOR, FFC/FPC 15P
1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P
1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P
< SWITCH >
************************************************************
*
*
S681
S682
S683
S685
S686
1-668-258-21 RELAY BOARD (EXCEPT US)
1-668-258-31 RELAY BOARD (US)
************
1-572-467-61
1-692-377-31
1-692-847-21
1-572-467-61
1-762-621-21
SWITCH, PUSH (1 KEY) (LIMIT IN)
SWITCH, PUSH (1 KEY) (REFRECT)
SWITCH, PUSH (1 KEY) (PROTECT)
SWITCH, PUSH (1 KEY) (CHUCKING IN)
SWITCH, PUSH (1 KEY) (PACK OUT)
< CONNECTOR >
CN408 1-506-987-11 PIN, CONNECTOR (PC BOARD) 5P
* CN409 1-580-159-11 PIN, CONNECTOR (PC BOARD) 7P
CN410 1-573-489-11 PIN, CONNECTOR (PC BOARD) 11P
************************************************************
S687
1-572-688-11 SWITCH, PUSH (1 KEY) (PB POSITION)
S688
1-762-621-21 SWITCH, PUSH (1 KEY) (REC POSITION)
************************************************************
– 126 –
TOP KEY
Ref. No.
Part No.
*
*
1-668-245-21 TOP KEY BOARD (EXCEPT US)
1-668-245-31 TOP KEY BOARD (US)
**************
Description
Remark
3-321-041-11 SCREW (M1.7X4), TAPPING
3-019-663-01 BUTTON (MEGABASS)
Ref. No.
Part No.
TRANS
Description
Remark
C981
1-164-506-11 CERAMIC CHIP
4.7uF
16V
C982
C983
C984
1-164-506-11 CERAMIC CHIP
1-164-506-11 CERAMIC CHIP
1-164-506-11 CERAMIC CHIP
4.7uF
4.7uF
4.7uF
16V
16V
16V
< CONNECTOR >
< CONNECTOR >
* CN403
* CN951
* CN952
CN953
* CN954
1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P
< RESISTOR >
R434
R435
R436
R437
R438
1-208-806-11
1-208-798-11
1-208-794-11
1-216-655-11
1-216-655-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
10K
4.7K
3.3K
1.5K
1.5K
0.50%
0.50%
0.50%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S831
S832
S833
1-692-014-11 SWITCH, KEY BOARD (DELETE)
1-692-014-11 SWITCH, KEY BOARD (INSERT)
1-692-014-11 SWITCH, KEY BOARD (AUTO PRESET, SHUF/
PGM)
S834
1-692-014-11 SWITCH, KEY BOARD(LINE LEVEL, MONO/ST,
REPEAT)
S835
1-692-014-11 SWITCH, KEY BOARD (MEGA BASS)
************************************************************
A-3321-535-A TRANS BOARD, COMPLETE (US)
A-3321-561-A TRANS BOARD, COMPLETE (EXCEPT US)
**********************
*
*
1-580-158-11
1-580-158-11
1-580-230-11
1-564-507-11
< DIODE >
D951
D952
D953
D954
D955
8-719-302-38
8-719-510-53
8-719-801-78
8-719-210-33
8-719-210-33
D956
D957
D958
8-719-210-33 DIODE EC10DS2
8-719-210-33 DIODE EC10DS2
8-719-210-33 DIODE EC10DS2
! F951
! F951
! F952
! F952
! F953
1-532-502-51
1-576-101-11
1-532-506-51
1-533-310-11
1-532-465-51
! F953
1-576-107-11 FUSE (3.15A/125V) (US)
JC955
FILM
FILM
FILM
FILM
FILM
0.022uF
0.022uF
0.022uF
0.022uF
0.01uF
C957
C958
C959
C960
C961
1-163-033-91
1-163-033-91
1-163-033-91
1-163-033-91
1-163-021-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.01uF
C963
C964
C965
C967
C968
1-163-035-00
1-163-035-00
1-126-968-11
1-163-035-00
1-163-035-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.047uF
100uF
0.047uF
0.047uF
C969
C970
C971
C972
C973
1-163-035-00
1-163-035-00
1-163-035-00
1-163-035-00
1-163-035-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
C974
C975
! C977
! C980
1-163-035-00
1-163-021-91
1-113-925-11
1-113-915-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
CERAMIC
0.047uF
0.01uF
0.01uF
0.001uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
10%
50V
50V
50V
50V
50V
20%
RBV-602-01
D4SB60L
1SS184
EC10DS2
EC10DS2
FUSE, TIME LAG (T1.25AL/250V) (EXCEPT US)
FUSE (1.25A/125V) (US)
FUSE, TIME LAG (T6.3AL/250V) (EXCEPT US)
FUSE, GLASS TUBE (6.3A/125V) (US)
FUSE, TIME LAG (T3.15AL/250V) (EXCEPT US)
< JUMPER RESISTOR >
< CAPACITOR >
1-136-157-00
1-136-157-00
1-136-157-00
1-136-157-00
1-136-153-00
DIODE
DIODE
DIODE
DIODE
DIODE
< FUSE >
1-533-293-11 FUSE HOLDER
7-685-648-79 SCREW +BVTP 3X12 TYPE2 N-S
C951
C952
C953
C954
C955
PIN, CONNECTOR (PC BOARD) 6P
PIN, CONNECTOR (PC BOARD) 6P
PIN, CONNECTOR (PC BOARD) 2P
PLUG, CONNECTOR 4P
1-216-296-00 METAL CHIP
0
5%
1/8W
< LINE FILTER >
! LF951
1-411-528-11 COIL (COMMON MODE CHOKE)
< IC LINK >
! PS951
! PS952
1-576-122-21 LINK, IC (0.4A)
1-576-123-21 LINK, IC (0.8A)
< RESISTOR >
R951
R952
R953
! R954
50V
50V
50V
50V
50V
1-216-057-00
1-216-073-00
1-216-121-91
1-202-725-00
METAL CHIP
METAL CHIP
RES,CHIP
SOLID
2.2K
10K
1M
3.3M
5%
5%
5%
10%
1/10W
1/10W
1/10W
1/2W
(US)
< TRANSFORMER >
50V
50V
50V
50V
50V
! T951
1-433-444-11 TRANSFORMER, POWER (EXCEPT US)
! T951
1-433-445-11 TRANSFORMER, POWER (US)
************************************************************
50V
10%
50V
20%
250V
20%
250V
(EXCEPT US)
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
– 127 –
TUNER
Ref. No.
Part No.
*
*
A-3321-536-A TUNER BOARD, COMPLETE (US)
A-3321-562-A TUNER BOARD, COMPLETE (EXCEPT US)
**********************
Description
Remark
1-126-963-11 ELECT
4.7uF
C1
1-163-243-11 CERAMIC CHIP
47PF
C2
1-126-924-11 ELECT
330uF
C2
1-163-021-91 CERAMIC CHIP
0.01uF
C3
1-126-960-11 ELECT
1uF
C3
1-163-021-91 CERAMIC CHIP
0.01uF
Part No.
Description
1-163-009-11 CERAMIC CHIP
0.001uF
C17
1-164-344-11 CERAMIC CHIP
0.068uF
C18
1-163-263-11 CERAMIC CHIP
330PF
20%
50V
(EXCEPT US)
5%
50V
(US)
20%
10V
(EXCEPT US)
10%
50V
(US)
20%
50V
(EXCEPT US)
C18
1-164-004-11 CERAMIC CHIP
0.1uF
C19
1-163-009-11 CERAMIC CHIP
0.001uF
C19
1-163-239-11 CERAMIC CHIP
33PF
5%
C20
1-163-227-11 CERAMIC CHIP
C20
1-163-263-11 CERAMIC CHIP
10%
C21
1-126-964-11 ELECT
20%
50V
(EXCEPT US)
20%
50V
(US)
20%
50V
(EXCEPT US)
10%
50V
(US)
C21
1-162-970-11 CERAMIC CHIP
C22
1-164-344-11 CERAMIC CHIP
0.068uF
10%
25V
C23
1-164-345-11 CERAMIC CHIP
0.082uF
10%
25V
C24
1-164-345-11 CERAMIC CHIP
0.082uF
10%
25V
20%
C25
1-162-964-11 CERAMIC CHIP
0.001uF
C25
1-163-239-11 CERAMIC CHIP
33PF
C26
1-162-964-11 CERAMIC CHIP
0.001uF
C26
1-163-227-11 CERAMIC CHIP
10PF
C27
1-162-927-11 CERAMIC CHIP
100PF
C27
1-162-964-11 CERAMIC CHIP
0.001uF
C28
1-163-021-91 CERAMIC CHIP
0.01uF
C29
1-163-021-91 CERAMIC CHIP
0.01uF
C30
1-104-640-11 FILM CHIP
C31
1-162-970-11 CERAMIC CHIP
C31
1-164-004-11 CERAMIC CHIP
C32
1-163-017-00 CERAMIC CHIP
C33
1-126-964-11 ELECT
10uF
C33
1-163-021-91 CERAMIC CHIP
0.01uF
(US)
C34
1-163-021-91 CERAMIC CHIP
0.01uF
(US)
10%
25V
(EXCEPT US)
5%
50V
(US)
10%
25V
(EXCEPT US)
C35
1-126-964-11 ELECT
10uF
C36
1-163-021-91 CERAMIC CHIP
0.01uF
C36
1-163-038-91 CERAMIC CHIP
0.1uF
50V
(US)
C4
1-126-960-11 ELECT
1uF
C4
1-126-963-11 ELECT
4.7uF
C5
1-126-964-11 ELECT
10uF
C5
1-163-021-91 CERAMIC CHIP
0.01uF
C6
1-126-924-11 ELECT
330uF
C6
1-126-964-11 ELECT
10uF
C7
1-126-964-11 ELECT
10uF
C7
1-163-021-91 CERAMIC CHIP
0.01uF
C8
1-163-024-91 CERAMIC CHIP
0.018uF
C9
1-126-934-11 ELECT
220uF
C9
C10
1-163-024-91 CERAMIC CHIP
1-126-960-11 ELECT
0.018uF
1uF
C11
1-126-960-11 ELECT
1uF
C11
1-163-021-91 CERAMIC CHIP
0.01uF
C12
1-163-021-91 CERAMIC CHIP
0.01uF
C12
1-164-004-11 CERAMIC CHIP
0.1uF
C13
1-163-024-00 CERAMIC CHIP
0.018uF
C13
C14
1-163-220-91 CERAMIC CHIP
1-163-024-00 CERAMIC CHIP
3PF
0.018uF
Remark
C17
< CAPACITOR >
C1
Ref. No.
10V
(US)
20%
50V
(EXCEPT US)
20%
50V
(EXCEPT US)
10%
50V
(US)
(US)
20%
10V
(EXCEPT US)
(US)
20%
50V
(US)
20%
50V
(US)
10%
50V
(EXCEPT US)
10%
50V
(EXCEPT US)
10%
25V
(US)
5%
50V
(EXCEPT US)
(US)
5%
50V
(EXCEPT US)
C14
1-164-004-11 CERAMIC CHIP
0.1uF
10%
25V
C15
1-163-131-00 CERAMIC CHIP
390PF
5%
50V
C15
1-164-345-11 CERAMIC CHIP
0.082uF
C16
1-163-234-11 CERAMIC CHIP
20PF
C16
1-164-345-11 CERAMIC CHIP
0.082uF
10%
50V
(US)
10% 25V
(EXCEPT US)
5%
50V
(EXCEPT US)
10%
25V
(US)
10%
50V
(US)
50V
(EXCEPT US)
10PF
0.5PF 50V
(EXCEPT US)
330PF
5%
50V
(US)
10uF
20%
50V
(US)
0.01uF 10%
25V
(EXCEPT US)
(US)
(US)
– 128 –
(US)
10%
50V
(EXCEPT US)
5%
50V
(US)
10%
50V
(EXCEPT US)
0.5PF 50V
(US)
5%
50V
(US)
10%
50V
(EXCEPT US)
10% 50V
(EXCEPT US)
10%
50V
(EXCEPT US)
0.22uF
5%
16V
(EXCEPT US)
0.01uF
10%
25V
(EXCEPT US)
0.1uF
10%
25V
(US)
0.0047uF 5%
50V
(EXCEPT US)
20%
50V
(US)
10%
50V
(EXCEPT US)
10%
50V
(US)
20%
50V
(US)
10%
50V
(US)
25V
(EXCEPT US)
TUNER
Ref. No.
C37
Part No.
Description
1-162-964-11 CERAMIC CHIP
Remark
0.001uF
10%
50V
(US)
C37
1-163-133-00 CERAMIC CHIP
470PF
50V
(EXCEPT US)
10%
50V
(US)
5%
50V
(EXCEPT US)
C38
1-162-964-11 CERAMIC CHIP
0.001uF
C38
1-163-234-11 CERAMIC CHIP
20PF
C39
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C39
1-163-038-91 CERAMIC CHIP
0.1uF
25V
C40
1-104-640-11 FILM CHIP
0.22uF
C41
1-163-251-11 CERAMIC CHIP
100PF
C42
1-162-964-11 CERAMIC CHIP
0.001uF
C42
1-163-021-91 CERAMIC CHIP
0.01uF
C43
1-126-934-11 ELECT
220uF
C44
1-163-009-11 CERAMIC CHIP
0.001uF
C45
1-126-160-11 ELECT
1uF
C46
1-163-009-11 CERAMIC CHIP
0.001uF
C47
1-126-924-11 ELECT
330uF
C47
1-164-004-11 CERAMIC CHIP
0.1uF
C48
1-164-346-11 CERAMIC CHIP
1uF
C50
1-164-816-11 CERAMIC CHIP
220PF
C51
1-163-263-11 CERAMIC CHIP
330PF
1-163-263-11 CERAMIC CHIP
C53
1-163-249-11 CERAMIC CHIP
C54
1-163-021-91 CERAMIC CHIP
C57
1-107-826-11 CERAMIC CHIP
C60
1-126-160-11 ELECT
330PF
25V
(EXCEPT US)
16V
(US)
5%
50V
(US)
10%
50V
(US)
5%
10%
50V
(EXCEPT US)
20%
10V
(US)
10%
50V
(US)
20%
50V
(US)
10%
50V
(US)
20%
1-164-004-11 CERAMIC CHIP
0.1uF
C72
1-163-251-11 CERAMIC CHIP
100PF
C73
1-163-133-00 CERAMIC CHIP
470PF
C74
1-162-927-11 CERAMIC CHIP
100PF
C75
1-163-251-11 CERAMIC CHIP
100PF
C76
1-163-251-11 CERAMIC CHIP
100PF
C77
1-162-927-11 CERAMIC CHIP
100PF
Part No.
Description
1-164-346-11 CERAMIC CHIP
1-126-924-11 ELECT
Remark
1uF
330uF
(US)
10%
25V
(EXCEPT US)
16V
(US)
2%
50V
(EXCEPT US)
5%
50V
(EXCEPT US)
16V
20%
10V
(EXCEPT US)
< FILTER >
CF1
CF2
CF2
CF3
CF3
1-760-127-11
1-760-127-11
1-760-468-11
1-760-127-11
1-760-468-11
CF4
CF5
1-579-762-11 VIBRATOR, CERAMIC
1-760-468-11 FILTER, CERAMIC (EXCEPT US)
FILTER, CERAMIC (US)
FILTER, CERAMIC (US)
FILTER, CERAMIC (EXCEPT US)
FILTER, CERAMIC (US)
FILTER, CERAMIC (EXCEPT US)
< COMPOSITION CIRCUIT BLOCK >
CFT1
CFT1
1-233-885-11 ENCAPSULATED COMPONENT(US)
1-239-173-11 ENCAPSULATED COMPONENT (EXCEPT US)
< CONNECTOR >
CN1
* CN2
* CN3
* CN40
1-568-444-11
1-580-154-11
1-580-154-11
1-580-154-11
SOCKET, CONNECTOR 13P
PIN, CONNECTOR (PC BOARD) 2P
PIN, CONNECTOR (PC BOARD) 2P
(US)
PIN, CONNECTOR (PC BOARD) 2P
(EXCEPT US)
< COMPOSITION CIRCUIT BLOCK >
CP1
CN42
10V
50V
(EXCEPT US)
82PF
5%
50V
(EXCEPT US)
0.01uF 10%
50V
(EXCEPT US)
0.1uF
10%
16V
(EXCEPT US)
1uF
20%
50V
(EXCEPT US)
C71
C78
C79
5%
(US)
C52
Ref. No.
1-536-354-00 POST PIN
1-536-354-00 POST PIN
< TRIMMER >
CT1
CT2
CT3
CT4
CT5
1-141-410-11
1-141-410-11
1-141-410-11
1-141-459-11
CAP, ADJ 10PF
(US)
CAP, ADJ 10PF
(EXCEPT US)
CAP, ADJ 10PF
(EXCEPT US)
CAP, TRIMMER (SEAL TYPE) 45PF
(EXCEPT US)
1-141-459-11 CAP, TRIMMER (SEAL TYPE) 45PF
(EXCEPT US)
5%
10%
25V
(EXCEPT US)
5%
50V
(EXCEPT US)
5%
50V
(EXCEPT US)
5%
50V
(EXCEPT US)
5%
50V
(EXCEPT US)
5%
50V
(EXCEPT US)
5%
50V
(EXCEPT US)
< DIODE >
D1
D2
D3
D3
D4
8-719-988-62
8-719-988-62
8-719-049-75
8-719-988-62
8-719-988-62
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355 (US)
1SS355 (US)
KV1520TL00 (EXCEPT US)
1SS355 (US)
1SS355
D5
D5
D6
D10
D40
8-719-049-75
8-719-988-62
8-719-988-62
8-719-988-62
8-719-988-62
DIODE
DIODE
DIODE
DIODE
DIODE
KV1520TL00 (US)
1SS355 (EXCEPT US)
1SS355 (US)
1SS355 (EXCEPT US)
1SS355 (EXCEPT US)
D41
D50
D51
8-719-988-62 DIODE 1SS355 (EXCEPT US)
8-719-988-62 DIODE 1SS355 (EXCEPT US)
8-719-988-62 DIODE 1SS355 (EXCEPT US)
< FERRITE BEAD >
FB1
FB2
FB3
FB4
FB4
– 129 –
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-11
1-414-235-21
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD (US)
INDUCTOR, FERRITE BEAD (EXCEPT US)
TUNER
Ref. No.
FB5
FB6
FB7
Part No.
Description
Remark
1-414-235-11 INDUCTOR, FERRITE BEAD (EXCEPT US)
1-414-235-11 INDUCTOR, FERRITE BEAD (EXCEPT US)
1-414-235-11 INDUCTOR, FERRITE BEAD (US)
< IC >
IC1
IC2
8-759-386-02 IC TA2008AN
8-759-459-42 IC BU2615FS
Ref. No.
Part No.
Description
Remark
R4
1-216-025-91 RES,CHIP
100
5%
R4
1-216-825-11 METAL CHIP
2.2K
5%
R5
1-216-025-91 RES,CHIP
100
5%
R5
1-216-073-00 METAL CHIP
10K
5%
R6
1-216-065-91 RES,CHIP
4.7K
5%
R6
1-216-833-11 METAL CHIP
10K
5%
R7
1-216-019-00 METAL CHIP
56
5%
R8
1-216-027-00 METAL CHIP
120
5%
R8
1-216-045-00 METAL CHIP
680
5%
R9
1-216-049-91 RES,CHIP
1K
5%
R9
1-216-609-11 METAL CHIP
18
0.5%
R10
1-216-821-11 METAL CHIP
1K
5%
R10
1-216-825-11 METAL CHIP
2.2K
5%
R11
1-216-836-11 METAL CHIP
18K
5%
R11
1-216-845-11 METAL CHIP
100K
5%
R12
1-216-073-00 METAL CHIP
10K
5%
R12
1-216-821-11 METAL CHIP
1K
5%
R13
1-216-049-91 RES,CHIP
1K
5%
R13
1-216-097-91 RES,CHIP
100K
5%
R14
1-216-825-11 METAL CHIP
2.2K
5%
< JUMPER RESISTOR >
JC1
JC2
JC50
1-216-295-00 METAL CHIP
1-216-295-00 METAL CHIP
1-216-864-11 METAL CHIP
0
0
0
5%
5%
5%
1/10W
1/10W
1/16W
(EXCEPT US)
< COIL >
L1
L2
L3
L4
L5
1-416-556-11
1-411-959-11
1-416-556-11
1-411-959-11
1-416-129-11
L10
L50
L52
1-233-306-31 ENCAPSULATED COMPONENT (EXCEPT US)
1-410-071-11 INDUCTOR
10mH (EXCEPT US)
1-216-017-91 RES,CHIP
47
5%
1/10W
(EXCEPT US)
1-500-284-21 INDUCTOR CHIP (EXCEPT US)
L70
COIL, AM ANT
COIL, AM OSC
COIL, AM ANT
COIL, AM OSC
COIL, LW ANT
(US)
(US)
(EXCEPT US)
(EXCEPT US)
(EXCEPT US)
< TRANSISTOR >
Q1
Q1
Q2
Q3
Q3
8-729-025-28
8-729-120-28
8-729-027-38
1-801-806-11
8-729-904-07
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SK1828 (EXCEPT US)
2SC1623-L5L6 (US)
DTA144EKA-T146 (US)
DTC144EKA-T146 (US)
FMG2 (EXCEPT US)
Q4
Q4
Q5
Q5
Q6
1-801-806-11
8-729-904-07
8-729-027-24
8-729-035-74
8-729-921-25
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC144EKA-T146 (EXCEPT US)
FMG2 (US)
DTA114TKA-T146 (EXCEPT US)
FMG4AT148 (US)
FMC2
Q7
Q7
Q8
Q8
Q50
8-729-027-24
8-729-120-28
8-729-025-28
8-729-035-74
8-729-027-38
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114TKA-T146 (US)
2SC1623-L5L6 (EXCEPT US)
2SK1828 (US)
FMG4AT148 (EXCEPT US)
DTA144EKA-T146 (EXCEPT US)
R15
1-216-057-00 METAL CHIP
2.2K
5%
R15
1-216-081-00 METAL CHIP
22K
5%
R16
1-216-097-91 RES,CHIP
100K
5%
Q51
Q52
Q53
Q54
Q57
8-729-039-73
8-729-931-02
8-729-920-38
8-729-920-31
8-729-119-32
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
FMA5A-T148 (EXCEPT US)
2SC2413KQ (EXCEPT US)
2SC2059K-N (EXCEPT US)
DTC343TK (EXCEPT US)
2SK193 (EXCEPT US)
R16
1-216-841-11 METAL CHIP
47K
5%
R17
1-216-037-00 METAL CHIP
330
5%
R18
1-216-020-91 METAL CHIP
62
5%
R18
1-216-089-91 RES,CHIP
47K
5%
R20
1-216-089-91 RES,CHIP
47K
5%
R21
1-216-089-91 RES,CHIP
47K
5%
R21
1-216-821-11 METAL CHIP
1K
5%
R22
1-216-089-91 RES,CHIP
47K
5%
< RESISTOR >
R1
1-216-065-91 RES,CHIP
4.7K
5%
R2
1-216-019-00 METAL CHIP
56
5%
R2
1-216-097-91 RES,CHIP
100K
5%
R3
1-216-037-00 METAL CHIP
330
5%
R3
1-216-081-00 METAL CHIP
22K
5%
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
1/10W
(US)
1/10W
(US)
1/10W
(EXCEPT US)
– 130 –
1/10W
(US)
1/16W
(EXCEPT US)
1/10W
(US)
1/10W
(EXCEPT US)
1/10W
(US)
1/16W
(EXCEPT US)
1/10W
(US)
1/10W
(US)
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
1/10W
(US)
1/16W
(US)
1/16W
(EXCEPT US)
1/16W
(EXCEPT US)
1/16W
(US)
1/10W
(US)
1/16W
(EXCEPT US)
1/10W
(US)
1/10W
(EXCEPT US)
1/16W
(US)
1/10W
(EXCEPT US)
1/10W
(US)
1/10W
(EXCEPT US)
1/16W
(US)
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
1/10W
(US)
1/10W
(US)
1/10W
(EXCEPT US)
1/16W
(US)
1/10W
(EXCEPT US)
TUNER
Ref. No.
Part No.
Description
R22
1-216-821-11 METAL CHIP
1K
5%
R23
1-216-821-11 METAL CHIP
1K
5%
R24
1-216-821-11 METAL CHIP
1K
5%
R25
1-216-833-11 METAL CHIP
10K
5%
R26
1-216-073-00 METAL CHIP
10K
5%
R26
1-216-864-11 METAL CHIP
0
5%
R27
1-216-833-11 METAL CHIP
10K
5%
R27
1-216-864-11 METAL CHIP
0
5%
R28
1-216-045-00 METAL CHIP
680
5%
R28
1-216-864-11 METAL CHIP
0
5%
R29
1-216-049-91 RES,CHIP
1K
5%
R29
1-216-833-11 METAL CHIP
10K
5%
R30
1-216-813-11 METAL CHIP
220
5%
R31
1-216-073-00 METAL CHIP
10K
5%
R31
1-216-825-11 METAL CHIP
2.2K
5%
R32
1-216-834-11 METAL CHIP
12K
5%
R32
1-216-845-11 METAL CHIP
100K
5%
R33
1-216-025-91 RES,CHIP
100
5%
R33
1-216-821-11 METAL CHIP
1K
5%
R34
R35
1-216-833-11 METAL CHIP
1-216-025-91 RES,CHIP
10K
100
5%
5%
R35
1-216-841-11 METAL CHIP
47K
R36
1-216-089-91 RES,CHIP
47K
R36
1-216-845-11 METAL CHIP
100K
R37
1-216-017-91 METAL CHIP
47
5%
R50
1-216-041-91 METAL CHIP
470
5%
R51
1-216-001-00 METAL CHIP
10
5%
R52
1-216-081-00 METAL CHIP
22K
5%
R53
1-216-057-00 METAL CHIP
2.2K
5%
R54
1-216-065-91 RES,CHIP
4.7K
5%
R55
1-216-065-91 RES,CHIP
4.7K
R56
1-216-065-91 RES,CHIP
4.7K
Remark
Ref. No.
1/16W
(US)
1/16W
(US)
1/16W
(US)
1/16W
R60
1-216-041-00 METAL CHIP
470
R61
1-216-825-11 METAL CHIP
2.2K
R70
1-216-295-00 METAL CHIP
0
R71
1-216-295-00 METAL CHIP
0
1/10W
(US)
1/16W
(EXCEPT US)
1/16W
(US)
1/16W
(EXCEPT US)
1/10W
(US)
1/16W
(EXCEPT US)
1/10W
(US)
1/16W
(EXCEPT US)
1/16W
(US)
1/10W
(EXCEPT US)
1/16W
(US)
1/16W
(US)
1/16W
(EXCEPT US)
1/10W
(EXCEPT US)
1/16W
(US)
1/16W
1/10W
(US)
5%
1/16W
(EXCEPT US)
5%
1/10W
(EXCEPT US)
5%
1/16W
(US)
1/10W
(US)
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
1/10W
(EXCEPT US)
5%
1/10W
(EXCEPT US)
5%
1/10W
(EXCEPT US)
Part No.
Description
Remark
5%
1/10W
(EXCEPT US)
5%
1/16W
(EXCEPT US)
5%
1/10W
(EXCEPT US)
5%
1/10W
(EXCEPT US)
< TERMINAL >
TB50
1-694-215-11 TERMINAL BOARD (FM EXT ANTENNA)
(EXCEPT US)
< TUNER >
* TU1
TU1
1-693-378-11 TUNER UNIT (EXCEPT US)
1-693-426-11 TUNER PACK (US)
< VIBRATOR >
X1
1-760-130-11 VIBRATOR, CRYSTAL (75kHz)
************************************************************
MISCELLANEOUS
**************
58
! 67
! 67
108
110
1-533-293-11
1-575-651-21
1-783-531-31
1-783-539-11
1-783-537-11
FUSE HOLDER
CORD, POWER (EXCEPT US)
CORD, POWER (US)
WIRE, PARALLEL (FFC) (15 CORE)
WIRE, PARALLEL (21 CORE)
111
153
159
160
161
1-783-538-11
1-660-966-11
1-783-542-11
1-783-540-11
1-790-045-11
WIRE, PARALLEL (FFC) (13 CORE)
OP RELAY FLEXIBLE BOARD
WIRE, PARALLEL (FFC) (29 CORE)
WIRE, PARALLEL (FFC) (19 CORE)
WIRE, PARALLEL (26 CORE)(60 mm)
162
165
! 217
303
308
1-777-517-11
1-790-046-11
8-583-028-02
1-690-530-21
1-660-965-11
WIRE, PARALLEL (15 CORE)
WIRE, PARALLEL (26 CORE)(172 mm)
DEVICE,MINI DISK KMS-260A
LEAD (WITH CONNECTOR)
PC BOARD, SLIDE FLEXIBLE
!309
ANT1
! F951
! F951
! F952
X-4946-311-1
1-501-480-11
1-576-101-11
1-532-502-51
1-533-310-11
OPTICAL PICK-UP (DAX-11A)
ANTENNA, TELESCOPIC
FUSE (1.25A/125V) (US)
FUSE, TIME LAG (1.25A/250V) (EXCEPT US)
FUSE, GLASS TUBE (6.3A/125V) (US)
! F952
! F953
! F953
FL401
HR901
1-532-506-51
1-532-465-51
1-576-107-11
1-517-744-11
1-500-396-11
FUSE, TIME LAG (6.3A/250V) (EXCEPT US)
FUSE, TIME LAG (3.15A/250V) (EXCEPT US)
FUSE (3.15A/125V) (US)
INDICATOR TUBE, FLUORESCENT
HEAD, OVER WRITE
M691
M801
M802
M901
M902
1-698-999-11
A-3303-403-A
A-3320-300-A
A-4672-135-A
A-4672-133-A
MOTOR, DC (LOADING)
MOTOR ASSY, SLED (INCLUDING GEAR)
MOTOR ASSY, TURN TABLE (SPINDLE)
MOTOR ASSY, SPINDLE
MOTOR ASSY, SLED (INCLUDING GEAR)
M903
S901
SP101
SP201
A-4672-134-A
1-571-099-21
1-505-829-11
1-505-829-11
MOTOR ASSY, LOADING (INCLUDING GEAR)
SWITCH (1 KEY) (LIMIT)
SPEAKER (8cm) (L-CH)
SPEAKER (8cm) (R-CH)
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
– 131 –
ZS-M7
Ref. No.
Part No.
! T951
1-433-445-11 TRANSFORMER, POWER (US)
Description
Remark
! T951
1-433-444-11 TRANSFORMER, POWER (EXCEPT US)
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
1-501-374-11 ANTENNA, LOOP
1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
3-704-222-11 LABEL, SERIAL NUMBER (PRINTER)
(EXCEPT US)
3-861-445-11 MANUAL, INSTRUCTION (ENGLISH) (US)
3-861-445-21 MANUAL, INSTRUCTION (ENGLISH, SPANISH)
(EXCEPT US)
3-861-445-31 MANUAL, INSTRUCTION (FRENCH, GERMAN)
(AEP, JE)
3-861-445-41 MANUAL, INSTRUCTION
(DUTCH, PORTUGUESE) (AEP)
3-861-445-51 MANUAL, INSTRUCTION (SWEDISH, FINNISH)
(AEP)
3-861-445-61 MANUAL, INSTRUCTION (ITALIAN) (AEP)
!
3-861-445-71 MANUAL, INSTRUCTION (POLISH, RUSSIAN)
(EE,Russian)
3-861-445-81 MANUAL, INSTRUCTION (CZECH,
HUNGALIAN) (EE,Russian)
4-991-047-01 LID, BATTERY CASE (FOR RMT-CM7)
8-917-623-90 REMOTE COMMANDER, SONY RMT-CM7 (US)
8-917-661-90 REMOTE COMMANDER RMT-CM7AD
(EXCEPT US)
X-3374-655-1 NET (L) ASSY, SP (EXCEPT US)
X-3374-656-1 NET (R) ASSY, SP (EXCEPT US)
************************************************************
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-621-773-86
7-685-850-04
7-627-552-27
7-685-548-19
7-627-553-17
SCREW +B 2.6X4
SCREW +BVTT 2X3 (S)
SCREW,PRECISION +P 1.7X2
SCREW +BTP 3X12 TYPE2 N-S
PRECISION SCREW +P 2X2 TYPE 3
#6
#7
#8
#9
#10
7-685-851-04
7-685-534-19
7-685-647-79
7-685-648-79
7-685-872-09
SCREW +BVTT 2X4 (S)
SCREW +BTP 2.6X8 TYPE2 N-S
SCREW +BVTP 3X10 TYPE2 N-S
SCREW +BVTP 3X12 TYPE2 N-S
SCREW +BVTT 3X8 (S)
#11
#12
#13
#14
#15
7-685-646-79
7-627-850-17
7-685-661-79
7-685-650-79
7-685-548-19
SCREW +BVTP 3X8 TYPE2 N-S
SCREW, PRECISION +P 1.4X2.5
SCREW +BVTP 4X12 TYPE2 N-S
SCREW +BVTP 3X16 TYPE2 N-S
SCREW, +BTP 3X12 TYPE2 N-S
#16
7-685-103-19 SCREW +P 2X5 TYPE2 NON-SLIT
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
– 132 –
ZS-M7
US Model
AEP Model
UK Model
Tourist Model
SERVICE MANUAL
2000. 03
SUPPLEMENT - 1
File this Supplement with the Service Manual.
Subject : EXPLODED VIEWS
(SPM-00011)
z
CHANGED PARTS LIST
EXPLODED VIEWS
FRONT CABINET SECTION (Service Manual See page 106)
Before Change
Ref. No.
3
4
Afrer Change
Part No.
Description
Part No.
Description
X-3374-656-1
NET (R) ASSY, SP
–––––––––––––––
NET (L) ASSY, SP
–––––––––––––––
X-3374-656-1
X-3376-521-1
X-3374-655-1
X-3376-520-1
NET (R) ASSY, SP (BLACK) (US)
NET (R) ASSY, SP (BLUE)(EXCEPT US)
NET (L) ASSY, SP (BLACK) (US)
NET (L) ASSY, SP (BLUE)(EXCEPT US)
X-3374-655-1
ACCESSORIES & PACKING MATERIALS (Service Manual See page 132)
Before Change
Ref. No.
Afrer Change
Part No.
Description
Part No.
X-3374-655-1
X-3374-656-1
NET (L) ASSY, SP (EXCEPT US)
NET (R) ASSY, SP (EXCEPT US)
X-3374-655-1 NET (L) ASSY, SP (BLACK) (EXCEPT US)
X-3374-656-1 NET (R) ASSY, SP (BLACK) (EXCEPT US)
Sony Corporation
9-923-346-82
Personal Audio Division Company
Description
2000C0267-1
Printed in Japan © 2000.3
Published by General Engineering Dept.
ZS-M7
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.2
2001.07
Correction of exploded views.
1.1
2000.03
SUPPLEMENT-1
1.0
1998.08
New
( SPM-01025 )