1
Download Kontron User's Guide - Integrated Exploration Systems GmbH
Transcript
Kontron User's Guide ETXexpress®-PC Document Revision 1.0 All not approved entries are marked! This page intentionally left blank Table of Contents Table of Contents 1 User Information ........................................................................................................ 6 1.1 1.2 1.3 1.4 1.5 1.6 2 Introduction .............................................................................................................. 8 2.1 2.2 2.3 2.4 2.5 3 ETXexpress®-PC ................................................................................................8 ETXexpress®-PC Module Overview .........................................................................8 Understanding ETXexpress® functionality ..............................................................9 ETXexpress® Documentation ............................................................................. 10 ETXexpress® Benefits....................................................................................... 10 Specification ............................................................................................................11 3.1 3.1.1 3.2 3.3 3.3.1 3.3.2 3.4 3.4.1 3.4.2 3.5 4 About This Document .........................................................................................6 Copyright Notice ...............................................................................................6 Trademarks ......................................................................................................6 Standards ........................................................................................................6 Warranty .........................................................................................................6 Technical Support..............................................................................................7 Functional Specification ................................................................................... 11 Block Diagram ................................................................................................ 15 Mechanical Specification .................................................................................. 16 Electrical Specification ..................................................................................... 16 Supply Current (Windows XP SP2) ....................................................................... 16 CMOS Battery Power Consumption ...................................................................... 17 Environmental Specification .............................................................................. 17 Temperature................................................................................................... 17 Humidity ....................................................................................................... 17 MTBF............................................................................................................. 18 Connector Pinouts .....................................................................................................19 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.7.1 4.7.2 4.7.3 4.7.4 4.7.5 Connector Location ......................................................................................... 19 Pinout Tables.................................................................................................. 20 Connector X1A ................................................................................................ 21 Connector X1B ................................................................................................ 25 Alternative pinout of HDMI................................................................................ 29 Alternative Pinout of Display Port ....................................................................... 29 Signal Description ........................................................................................... 30 PCIexpress x1 lanes ......................................................................................... 30 USB .............................................................................................................. 30 SATA ............................................................................................................. 30 Audio ............................................................................................................ 30 Serial IRQ ...................................................................................................... 31 Kontron User's Guide ETXexpress®-PC iii Table of Contents 4.7.6 4.7.7 4.7.8 4.7.9 4.7.10 4.7.11 4.7.12 4.7.13 4.7.14 4.7.15 4.7.16 4.7.17 5 Special Features ........................................................................................................35 5.1 5.2 5.3 5.3.1 6 Cooling Solution ............................................................................................. 38 Limitation ...................................................................................................... 38 Reset Behavior ............................................................................................... 38 Booting with a single memory module ................................................................. 38 Standby with Microsoft Vista.............................................................................. 38 12V only ........................................................................................................ 38 IDE (PATA) ..................................................................................................... 38 Passive Cooling Trip Point ................................................................................. 39 Design Considerations................................................................................................40 7.1 7.2 7.3 7.3.1 7.3.2 7.3.3 8 Watchdog Timer .............................................................................................. 35 General Purpose Input and Output ...................................................................... 35 Usage of Different Graphic interfaces .................................................................. 36 Available Graphic interfaces .............................................................................. 36 Important Information...............................................................................................38 6.1 6.2 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 7 VGA Output .................................................................................................... 31 LVDS Flat Panel Interface (JILI).......................................................................... 31 PCIexpress Graphics ......................................................................................... 31 SDVO ............................................................................................................ 31 HDMI ............................................................................................................ 32 Displayport .................................................................................................... 32 Ethernet ........................................................................................................ 32 Power Control ................................................................................................. 32 Power Management ......................................................................................... 32 Miscellaneous Circuits ...................................................................................... 33 PCI Bus.......................................................................................................... 33 IDE Port ......................................................................................................... 33 Thermal Management ....................................................................................... 40 Heatspreader Dimensions ................................................................................. 41 ETXexpress-PC onboard fan connector ................................................................. 42 Location and pin-out of fan connector ................................................................. 42 BIOS settings for fan control ............................................................................. 44 Electrical Characteristics ................................................................................... 44 System Resources ......................................................................................................45 8.1 8.2 8.3 8.4 8.5 Interrupt Request lines..................................................................................... 45 Direct Memory Access (DMA) Channels ................................................................. 46 Memory Area .................................................................................................. 47 I/O Address Map ............................................................................................. 47 Inter-IC (I2C) Bus ............................................................................................ 47 Kontron User's Guide ETXexpress®-PC iv Table of Contents 8.6 8.7 8.8 9 BIOS Operation .........................................................................................................48 9.1 9.2 9.2.1 9.3 9.3.1 9.3.2 9.3.3 9.3.4 9.3.5 10 JIDA Information ............................................................................................ 82 Appendix B: Architecture Information ..........................................................................83 11.1 11.1.1 11.1.2 11.2 11.3 11.3.1 11.3.2 11.3.3 11.4 12 Determining the BIOS Version ............................................................................ 48 Setup Guide ................................................................................................... 48 Start AMI® BIOS Setup Utility ............................................................................ 48 BIOS Setup Menus ........................................................................................... 50 Main Menu ..................................................................................................... 50 Advanced Menu............................................................................................... 52 Boot Menu ..................................................................................................... 79 Security Menu ................................................................................................. 81 Exit Menu ...................................................................................................... 81 Appendix A: JIDA Standard .........................................................................................82 10.1 11 System Management (SM)Bus ............................................................................ 47 JILI-I2C Bus ................................................................................................... 47 SDVO-I2C Bus ................................................................................................. 47 Buses ............................................................................................................ 83 ISA, Standard PS/2 – Connectors ........................................................................ 83 PCI/104......................................................................................................... 83 General PC Architecture .................................................................................... 83 Ports............................................................................................................. 84 RS-232 Serial ................................................................................................. 84 Serial ATA ...................................................................................................... 84 USB .............................................................................................................. 84 Programming ................................................................................................. 84 Appendix C: Document Revision History ........................................................................86 Kontron User's Guide ETXexpress®-PC v 1 User Information 1 User Information 1.1 About This Document This document provides information about products from Kontron Embedded Modules GmbH and/or its subsidiaries. No warranty of suitability, purpose, or fitness is implied. While every attempt has been made to ensure that the information in this document is accurate, the information contained within is supplied “as-is” and is subject to change without notice. For the circuits, descriptions and tables indicated, Kontron assumes no responsibility as far as patents or other rights of third parties are concerned. 1.2 Copyright Notice Copyright © 2003-2007 Kontron Embedded Modules GmbH All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron Embedded Modules GmbH. DIMM-PC®, PISA®, ETX®, ETXexpress®, microETXexpress™, X-board®, DIMM-IO® and DIMM-BUS® are trademarks or registered trademarks of Kontron Embedded Modules GmbH. Kontron is trademark or registered trademark of Kontron AG. 1.3 Trademarks The following lists the trademarks of components used in this board. 1.4 ® IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corp. ® Microsoft is a registered trademark of Microsoft Corp. ® Intel is a registered trademark of Intel Corp. ® All other products and trademarks mentioned in this manual are trademarks of their respective owners. Standards Kontron Embedded Modules GmbH is certified to ISO 9000 standards. 1.5 Warranty This Kontron Embedded Modules GmbH product is warranted against defects in material and workmanship for the warranty period from the date of shipment. During the warranty period, Kontron Embedded Modules GmbH will at its discretion decide to repair or replace defective products. Within the warranty period, the repair of products is free of charge as long as warranty conditions are observed. Kontron User's Guide ETXexpress®-PC 6 1 User Information The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental specifications or improper installation or maintenance. Kontron Embedded Modules GmbH will not be responsible for any defects or damages to other products not supplied by Kontron Embedded Modules GmbH that are caused by a faulty Kontron Embedded Modules GmbH product. 1.6 Technical Support Technicians and engineers from Kontron Embedded Modules GmbH and/or its subsidiaries are available for technical support. We are committed to making our product easy to use and will help you use our products in your systems. Please consult our Web site at http://www.kontron.com/support for the latest product documentation, utilities, drivers and support contacts. In any case you can always contact your board supplier for technical support. Kontron User's Guide ETXexpress®-PC 7 2 Introduction 2 Introduction 2.1 ETXexpress®-PC Based on the COM Express standard, Kontron’s ETXexpress®-PC, powered by a variety of Intel®'s Core2Duo® and CeleronM® processors, is a next-generation embedded module that brings advanced technology to tomorrow’s applications, as well as continuing today’s legacy devices. Built around serial differential signaling technologies, ETXexpress®-PC modules incorporate the following interfaces into 95 x 125 small form factor embedded module: ® PCI Express, which provides a high performance I/O infrastructure with transfer rates starting at 2.5 Giga transfers per second over a x1 PCI Express lane ® PCI ® Serial ATA (SATA II) ® USB 2.0 ® LVDS ® Azalia High Definition Audio ® Advanced Configuration and Power Interface (ACPI) for optimized power management The ETXexpress®-PC is built around the Intel® Core2Duo® and CeleronM® processor and the Intel® GS45 chipset. These modules feature the most current desktop features such as USB 2.0, SATA, and PCI Express buses. The ETXexpress®-PC delivers up to 8GB DDR3 RAM. For applications that require advanced real-time video capabilities, the ETXexpress®-PC has integrated graphics with 2D, 3D and Motion Video Acceleration and also supports PCI Express graphics, two SDVO ports or two HDMI capable DVI ports. Fast communications are possible courtesy of a Gigabit Ethernet port. The ETXexpress®-PC supports up to 6 PCI Express x1 Lanes and PCI Express cards (only when 10/100MB Ethernet is equipped) as well as established hardware solutions based on current buses such as 32-bit PCI. A Gigabit Ethernet port provides fast connectivity to LAN/WAN and 8 USB 2.0 ports provide fast and sufficient interfaces for external peripherals. ETXexpress®-PC modules also provide the following interfaces that are always located in the same physical position on each board: PCI-express, PCI32, USB, serial ATA (SATA), parallel ATA (PATA), LVDS Multi Media ports, as well as an ACPI (Advanced Configuration and Power Interface) for optimized power management. Mounting holes on the board provide secure mounting to allow the module increased shock and vibration resistance. 2.2 ETXexpress®-PC Module Overview The international COM Express standard defines two new form factor sizes: Basic and Extended. The primary difference between the Basic and Extended size is a larger board size and thermal envelope in the Extended size. The ETXexpress®-PC follows the basic form factor. Kontron User's Guide ETXexpress®-PC 8 2 Introduction Five module Pin-out Type definitions exist for Basic and Extended modules. Pin-out Types 1-5 apply to Basic and Extended module form factors. Pin-out Types 1-5 offer different functionalities. For a complete explanation of the features of each of the Pin-out Types 1-5, please see the COMexpress Specification. The ETXexpress®-PC uses the Pin-out Type 2 architecture, which includes PCI and IDE interfaces. These modules either use onboard graphics capabilities or may use 8 PEG lanes to connect to an external video controller. In case of onboard graphics, PEG pins may be alternatively used for SDVO or DVI ports. Pin-out Type 2 features include: 2.3 ® Dual 220 pin connectors (Primary Connector: Rows A-B and Secondary Connector: Rows C-D, 440 pins total) ® 32-bit PCI interface ® IDE port (to support legacy ATA devices) ® Up to 6 PCI Express general purpose lanes ® One, x16 PCI Express Graphics (PEG) slot ® Up to 8 USB 2.0 ports; 4 shared over-current lines ® Up to 4 Serial ATA ports ® Dual 18-bit LVDS channels (with 24 bit dithering) ® Analog VGA and TV Out: Composite Video, S-Video, Component Video (YPbPr) ® High Definition Audio digital audio interface (external CODEC) ® Single Gigabit Ethernet interface with integrated PHY ® +12V primary power supply input, +5V standby and 3 V RTC power supplies Understanding ETXexpress® functionality All Kontron ETXexpress® modules contain two connectors; each of it has two rows. The primary connector has two rows called Row A and Row B. The secondary connector has two rows called Row C and Row D. The primary connector (Row A and Row B) feature the following legacy-free functionality: ® Ethernet ® Serial ATA (SATA) ® USB 2.0 ® LVDS/VGA and dual display video ® Intel High Definition Audio (Azalia) ® LPC (low pin count) Bus The secondary connector (Row C and Row D) provides support for the following buses and I/O: ® PCI Express ® PCI ® IDE Kontron User's Guide ETXexpress®-PC 9 2 Introduction 2.4 ETXexpress® Documentation This product manual serves as one of three principal references for an ETXexpress® design. It documents the specifications and features of ETXexpress®-PC. The other two references, which are available from your Kontron Support or from PICMG®, include: Note: 2.5 ® The COMexpress Specification defines the ETXexpress® module form factor, pinout, and signals. ® The ETXexpress® Component SBC™ Design Guide serves as a general guide for baseboard design, with a focus on maximum flexibility to accommodate a wide range of ETXexpress® modules. Some of the information contained within this product manual applies only to certain product revisions (CE: xxx). If certain information applies to specific product revisions (CE: xxx) it will be stated. Please check the product revision of your module to see if this information is applicable. ETXexpress® Benefits Embedded technology extended express (ETXexpress) modules are very compact (125 x 95 mm, 12mm thick), highly integrated computers. All ETXexpress® modules feature a standardized form factor and a standardized connector layout that carry a specified set of signals. Each ETXexpress® module is based on connector type 2 of the COMexpress specification. This standardization allows designers to create a single-system baseboard that can accept present and future ETXexpress® modules. ETXexpress® modules include common personal computer (PC) peripheral functions such as: ® Graphics ® USB ports ® Ethernet ® Sound ® IDE (and SATA) The baseboard designer can optimize exactly how each of these functions implements physically. Designers can place connectors precisely where needed for the application on a baseboard designed to optimally fit a system’s packaging. A peripheral PCI bus can be implemented directly on the baseboard rather than on mechanically unwieldy expansion cards. The ability to build a system on a single baseboard using the computer as one plug-in component simplifies packaging, eliminates cabling, and significantly reduces system-level cost. A single baseboard design can use a range of ETXexpress® modules. This flexibility can differentiate products at various price/performance points, or to design future proof systems that have a built-in upgrade path. The modularity of an ETXexpress® solution also ensures against obsolescence as computer technology evolves. A properly designed ETXexpress® baseboard can work with several successive generations of ETXexpress® modules. An ETXexpress® baseboard design has many advantages of a custom, computer-board design but delivers better obsolescence protection, greatly reduced engineering effort, and faster time to market. Kontron User's Guide ETXexpress®-PC 10 3 Specification 3 Specification 3.1 Functional Specification Processor ® Intel® Core2Duo Processor (Penryn) ® Up to 1066 MHz CPU bus (depends on used processor) ® Up to 1066 MHz memory bus (depends on used processor and memory) Bus Processor features ® Support for SSE, SSE2, SSE3, SSE4.1, MMX™ ® Supports Intel® architecture with Intel® Wide Dynamics Execution ® Supports L1 chache-to-cache (C2C) transfer ® Advanced power management features including Enhanced Intel SpeedStep® Technology and dynamic FSB frequency switching ® Intel® 64 architecutre ® Supports enhanced Intel Virtualization Technology ® Enhanced Intel® Dynamic Acceleration ® Intel® Deep Power Down low-power state with P_LVL6 I/O Support ® Support for Intel® Trusted Execution Technology Processor cache l2 ® 6 MB or 3 MB on-die 2nd level cache (depends on used processor) ® Intel® GS45 ® Intel® ICH-9M ® Dual channel DDR3-SO-DIMM which allows up to 8GB RAM Chipset Memory PCI Express Graphics (PEG): Intel® GS45 ® One 16-lane PCI Express port for external PCI Express based graphic cards PCI Express: Intel® ICH-9M ® 5 PCI Express x1 lanes PCI32: Intel® ICH-9M ® Parallel PCI Bus 32 bit MHz according to PCI2.3 IDE: Intel® ICH-9M ® Single PATA channel support Kontron User's Guide ETXexpress®-PC 11 3 Specification ® Supports PIO, Multi-Word DMA and Ultra-DMA 33/66/100/133 modes Serial ATA: Intel® ICH-9M ® 4 Channels Serial ATA ® SATA Spec. Rev. 2.0 up to 300MB/s per channel ® SATA II (AHCI) Feature Native Command Queuing (NCQ) Auto Activate for DMA Hot Plug Support Asynchronous Signal Transfer 3 Gb/s Transfer Rate ATAPI Asynchronous Notification Host & Link Initiated Power Management Staggered Spin-Up Command Completion Coalescing Port Multiplier External SATA AHCI disabled N/A N/A N/A N/A Supported N/A N/A Supported N/A N/A N/A AHCI enabled Supported Supported Supported Supported Supported Supported Supported Supported N/A Supported Supported Universal Serial Bus: Intel® ICH-9M ® 8 USB 1.1/2.0 ports (UHCI and EHCI) ® USB legacy keyboard support ® USB floppy, CD-ROM, Hard drive and memory stick boot support Gigabit Ethernet: Intel® 82567 ® Fully compatible with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab Internal Graphics: Intel® 82567 ® Onboard video graphics array: Intel® GS45 ® Intel Gen 5.0 integrated graphics engine with 10 fully programmable cores ® 533-MHz core render clock @ 1.05-V core voltage ® Supports iHDMI/DVI, DP, TV-Out, LVDS, CRT and SDVO ® Intel® Dynamic Video Memory Technology (Intel® DVMT 5.0) ® Video Capture via x1 concurrent PCI Express port ® PAVP (Protected Audio-Video Path) support for Protected Intel® HD Audio (Video ® and Audio) Playback ® High performance MPEG-2 decoding ® WMV9 (VC-1) and H.264 (AVC) support ® Hardware acceleration for MPEG2 VLD/iDCT ® Microsoft DirectX*10 support ® Blu-ray* support @ 40 Mb/s Kontron User's Guide ETXexpress®-PC 12 3 Specification ® Hardware motion compensation ® Intermediate Z in classic rendering Dual-Channel LVDS: Intel® 82567 ® 25-112-MHz single/dual-channel ® Single channel LVDS interface support: 1 x 18 bpp OR 1 x 24 bpp (Type 1 only, compatible with VESA LVDS color mapping) ® Dual-channel LVDS interface support:2 x 18 bpp OR 2 x 24 bpp panel support ® TFT panel type supported ® Pixel dithering for 18-bit TFT panel to emulate 24-bpp true color displays ® Panel Fitting. Panning and Center mode supported ® Standard Panel Working Group (SPWG) v.3.5 specification compliant ® Spread spectrum clocking support ® Panel power sequencing support ® Integrated PWM interface for LCD backlight inverter control DisplayPort (DP) : Intel® 82567 The GMCH supports three DP ports muxed on the PCI Express interface ® 1.62 Gb/s and 2.7 Gb/s ® 1, 2 or 4 data lanes ® 8b 10b coding ® Hot-Plug detect support ® HDCP support Integrated HDMI (iHDMI) : Intel® 82567 ® DVI also supported on same interface ® Single TMDS Link ® 8 bpc only supporting RGB - no YCrCb4:4:4 and YCrCb4:2:2 support ® Data Island Packets including null, AVI Infoframe, audio samples and more ® Video support for CEA modes 480i/p, 576i/p, 720p, 1080i/p and PC modes though dot clock ® HDMI Source only – not a receiver device ® HDCP support ® Support for HDMI repeaters ® Intel HD Audio support ® Integrated Intel HD Audio codec ® Dolby* AC3 compress, Dolby* Digital, Dolby* DTS (full support) ® PCM audio support Kontron User's Guide ETXexpress®-PC 13 3 Specification SDVO Ports: Intel® 82567 ® Two SDVO ports supported ® SDVO pins are muxed onto the PCI Express Graphics-attach port pins ® DVI 1.0 support for External Digital Monitor ® Downstream HDCP Support but no upstream HDCP support ® Display Hot-Plug support ® Supports appropriate external SDVO components (HDMI, DVI, LVDS, TV-Out) ® I2C channel provided for control Analog CRT: Intel® 82567 ® Integrated 300-MHz DAC ® Analog monitor support up to QXGA ® Support for CRT Hot-Plug TV-Out: Intel® 82567 ® MacroVision not supported ® Overscaling ® NTSC/PAL ® Component, S-Video and Composite Output Interfaces ® HDTV graphics mode support HD Audio: Intel® ICH-9M ® Up to 3 bit sample depth ® Up to 192 kHz sample rate ® Supports up to 4 codecs Kontron User's Guide ETXexpress®-PC 14 3 Specification Block Diagram PCIe Connector AB Connector CD X2/X4 DMI 3.1.1 Kontron User's Guide ETXexpress®-PC 15 3 Specification 3.2 Mechanical Specification Dimension 3.3 ® 95.0 x 125.0 mm ® Height approx. 12 mm (0.4”) Electrical Specification Supply Voltage Note: ® 12 DC +/- 5% or ® 8.5V DC to 18V DC wide range input It is not possible to use E2 rated boards with wide range input! Supply Voltage Ripple ® 3.3.1 Maximum 100mV peak to peak 0-20 MHz Supply Current (Windows XP SP2) The tested boards were mounted on a Kontron Evaluation Board (Article number: 38100-0000-00-0), a mouse and a keyboard were connected. The Power-consumption tests were executed during Windows XP SP2 by using a tool to stress the CPU (100 % load). The power measurements values were acquired after 15 min full load and a stable CPU die temperature. To ensure a stable die temperature a corresponding heatsink was used to hold the temperature under the critical trip point. All boards were equipped with DDR3 SDRAM. The Modules were tested using maximum CPU frequency. Processor / board revision MHz RAM MB Full Load Idle 1024 [A]12V 3,14 [A]5V_SB 0,06 [W] 37,98 [A]12V 0,64 [A]5V_SB 0,06 [W] 7,99 1024 2,44 0,06 29,58 0,65 0,06 8,13 1024 1,40 0,06 17,10 0,62 0,06 7,78 1200 1024 1,09 0,06 13,32 0,63 0,06 7,98 MHz RAM MB SP9300 2x2266 1024 [A]12V TBD [A]5V_SB TBD SL9400 2x1866 1024 TBD SU9300 2x1200 1024 TBD CM722 1200 1024 TBD SP9300 2x2266 SL9400 2x1866 SU9300 2x1200 CM722 Processor / board revision Kontron User's Guide ETXexpress®-PC Idle with Speedstep Standby S1 [A]12V TBD [A]5V_SB TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD 16 [W] [W] 3 Specification Processor / board revision S3hot S3cold MHz RAM MB SP9300 2x2266 1024 [A]12V TBD [A]5V_SB TBD SL9400 2x1866 1024 TBD SU9300 2x1200 1024 TBD CM722 1200 1024 TBD MHz RAM MB SP9300 2x2266 1024 [A]12V 0,00 [A]5V_SB 0,19 [W] 0,95 SL9400 2x1866 1024 0,00 0,26 1,30 SU9300 2x1200 1024 0,00 0,27 1,37 CM722 1200 1024 0,00 0,26 1,28 Processor / board revision 3.3.2 [W] [A]12V TBD [A]5V_SB TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD [W] Soft Off S5 CMOS Battery Power Consumption tbd 3.4 Environmental Specification 3.4.1 Temperature Operating: (with Kontron Embedded Modules heat-spreader plate assembly): ® Ambient temperature: 0°C to 60°C ® Maximum heatspreader-plate temperature: 0°C to 60°C Non-operating: -30°C to 85°C Note: The maximum operating temperature with the heatspreader plate is the maximum measurable temperature on any spot on the heatspreader’s surface. You must maintain the temperature according to the above specification. Operating (without Kontron Embedded Modules heat-spreader plate assembly): ® Maximum operating temperature: 0°C to 60°C Non operating: -30 to +85 °C Note: 3.4.2 The maximum operating temperature is the maximum measurable temperature on any spot on a module’s surface. You must maintain the temperature according to the above specification. Humidity ® Operating: 10% to 90% (non condensing) ® Non operating: 5% to 95% (non condensing) Kontron User's Guide ETXexpress®-PC 17 3 Specification 3.5 MTBF The following MTBF (Mean Time Between Failure) values were calculated using a combination of manufacturer’s test data, if the data was available, and a Bellcore calculation for the remaining parts. The Bellcore calculation used is “Method 1 Case 1”. In that particular method the components are assumed to be operating at a 50 % stress level in a 40° C ambient environment and the system is assumed to have not been burned in. Manufacturer’s data has been used wherever possible. The manufacturer’s data, when used, is specified at 50° C, so in that sense the following results are slightly conservative. The MTBF values shown below are for a 40° C in an office or telecommunications environment. Higher temperatures and other environmental stresses (extreme altitude, vibration, salt water exposure, etc.) lower MTBF values. ® Notes: System MTBF (hours) : 147066 Fans usually shipped with Kontron Embedded Modules GmbH products have 50,000-hour typical operating life. The above estimates assume no fan, but a passive heat sinking arrangement. Kontron User's Guide ETXexpress®-PC 18 4 Connector Pinouts 4 Connector Pinouts 4.1 Connector Location There are 2 connectors on the basic sized module. Connector X1A and Connector X1B are shown in the following drawing. It is a top layer view and the connectors are seen "through" the PCB. Each connector consist s of 2 connector rows. Connector X1A has rows A and B and connector X1B has rows C and D. Kontron User's Guide ETXexpress®-PC 19 4 Connector Pinouts 4.2 Pinout Tables Type I/O-3,3 I/O-5T I/O-5 I-3,3 I/OD I-5T OA OD O-1,8 O-3,3 O-5 DP-I/O DP-I DP-O PU PD PWR Notes: Description Bi-directional 3,3 V IO-Signal Bi-dir. 3,3V I/O (5V Tolerance) Bi-directional 5V I/O-Signal 3,3V Input Bi-directional Input/Output Open Drain 3,3V Input (5V Tolerance) Output Analog Output Open Drain 1,8V Output 3,3V Output 5V Output Differential Pair Input/Output Differential Pair Input Differential Pair Output Pull-Up Resistor Pull-Down Resistor Power Connection To protect external power lines of peripheral devices, make sure that: the wires have the right diameter to withstand the maximum available current the enclosure of the peripheral device fulfils the fire-protection requirements of IEC/EN60950 Kontron User's Guide ETXexpress®-PC 20 4 Connector Pinouts 4.3 Connector X1A Connector X1A (Signal Levels A1-A55) Pin A1-A55 Pin Signal A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 Note: GND GBE0_MDI3GBE0_MDI3+ GBE0_LINK10 GBE0_LINK10 GBE0_MDI2GBE0_MDI2+ GBE0_LINK# GBE0_MDI1GBE0_MDI1+ GND GBE0_MDI0GBE0_MDI0+ GBE0_CTREF SUS_S3# SATA0_TX+ SATA0_TXSUS_S4# SATA0_RX+ SATA0_RXGND SATA2_TX+ SATA2_TXSUS_S5# SATA2_RX+ SATA2_RXBATLOW# ATA_ACT# AC_SYNC AC_RST# GND AC_BITCLK AC_SDOUT BIOS_DISABLE THRMTRIP# USB6USB6+ USB_6_7_OC# USB4USB4+ GND USB2USB2+ USB_2_3_OC# USB0USB0+ VCC_RTC EXCD0_PERST# EXCD0_CPPE# LPC_SERIRQ GND PCIE_TX5+ PCIE_TX5GPI0 PCIE_TX4+ Description Power Ground GBE0_MDI3_N | Ethernet Receive Data GBE0_MDI3_P | Ethernet Receive Data GBE0_LINK100# | Ethernet Speed LED GBE0_LINK1000# | Ethernet Speed LED GBE0_MDI2_N | Ethernet Receive Data GBE0_MDI2_P | Ethernet Receive Data GBE0_LINK# | LAN Link LED GBE0_MDI1_N | Ethernet Receive Data GBE0_MDI1_P | Ethernet Receive Data Power Ground GBE0_MDI0_N | Ethernet Transmit GBE0_MDI0_P | Ethernet Transmit Data GBE0_CTREF PM_SLP_S3_EXT# SATA_TX0_P | SATA 0 Transmit Data + SATA_TX0_N | SATA 0 Transmit Data PM_SLP_S4_EXT# SATA_RX0_P | SATA 0 Receive Data + SATA_RX0_N | SATA 0 Receive Data Power Ground SATA_TX2_P | SATA 2 Transmit Data + SATA_TX2_N | SATA 2 Transmit Data PM_SLP_S#5 SATA_RX2_P | SATA 2 Receive Data + SATA_RX2_N | SATA 2 Receive Data PM_BATLOW# | Battery Low ATA_LED# | SATA LED HDA_SYNC | HD Audio Sync HDA_RST# | HD Audio Reset Power Ground HDA_BITCLK | HD Audio Clock HDA_SDOUT | HD Audio Data BIOS_DISABLE# EXT_THRMTRIP# USB6_N | USB Data – Port6 USB6_P | USB Data + Port6 USB_67_OC# | USB OverCurrent Port USB4_N | USB Data - Port4 USB4_P | USB Data + Port4 Power Ground USB2_N | USB Data - Port2 USB2_P | USB Data + Port2 USB_23_OC# | USB OverCurrent Port USB0_N | USB Data - Port0 USB0_P | USB Data + Port0 V_BAT EXCD0_PERST#|Express card reset EXCD0_CPPE#| capable c. request LPC_SERIRQ | Serial Interrupt Request Power Ground opt. PCI Express lane 5 + Transmit opt. PCI Express lane 5 - Transmit EXT_GPI0 | General Purpose Input 0 PCI Express lane 4 + Transmit [ LAN | Power | USB | SATA | PCIe | AUDIO] Type Termination Comment PWR DP-I DP-I O-3,3 O-3,3 DP-I DP-I OD DP-I DP-I PWR DP-O DP-O O-1,8 O-3,3 DP-O DP-O O-3,3 DP-I DP-I PWR DP-O DP-O O-3,3 DP-I DP-I I-3,3 O-3,3 O-3,3 O-3,3 PWR O-3,3 O-3,3 I-3,3 I/ODP-I/O DP-I/O I-3,3 DP-I/O DP-I/O PWR DP-I/O DP-I/O I-3,3 DP-I/O DP-I/O PWR O-3,3 I-3,3 IO-3,3 PWR Nc Nc I-3,3 DP-O PU 10k 3,3V (S5) PU 8k25 3,3V PU 10k 3,3V (S0) PU 10k 3,3V (S0) PU 10k 3,3V (S5) PU 10k 3,3V (S5) PU 10k 3,3V (S5) PU 10k 3,3V (S0) PU 10k 3,3V (S0) - is on a power rail controlled by Intels ME int. PU 15k in ICH9 only active if opt. for x4: PU 1k 3,3V(S0) int. PD 20k in ICH9 int. PD 20k in ICH9 active only in S3 int. PD 20k in ICH9– x4 => PU 1k int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant int. PD 15k in ICH9 | 5V tolerant just available if no GbEthernet PHY is just available if no GbEthernet PHY is - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 21 4 Connector Pinouts Connector X1A (Signal Levels A56-A110) Pin A56-A110 Pin Signal A56 A57 A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76 A77 A78 A79 A80 A81 A82 A83 A84 A85 A86 A87 A88 A89 A90 A91 A92 A93 A94 A95 A96 A97 A98 A99 A100 A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 Note: PCIE_TX4GND PCIE_TX3+ PCIE_TX3GND PCIE_TX2+ PCIE_TX2GPI1 PCIE_TX1+ PCIE_TX1GND GPI2 PCIE_TX0+ PCIE_TX0GND LVDS_A0+ LVDS_A0LVDS_A1+ LVDS_A1LVDS_A2+ LVDS_A2LVDS_VDD_EN LVDS_A3+ LVDS_A3GND LVDS_A_CK+ LVDS_A_CKLVDS_I2C_CK LVDS_I2C_DAT GPI3 KBD_RST# KBD_A20GATE PCIE0_CK_REF+ PCIE0_CK_REFGND RSVD RSVD GPO0 RSVD RSVD GND VCC_12V VCC_12V VCC_12V GND VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V GND Description Type PCI Express lane 4 - Transmit Power Ground PCI Express lane 3 + Transmit PCI Express lane 3 - Transmit Power Ground PCI Express lane 2 + Transmit PCI Express lane 2 - Transmit EXT_GPI1 | General Purpose Input 1 PCI Express lane 1 + Transmit PCI Express lane 1 - Transmit Power Ground EXT_GPI2 | General Purpose Input 2 PCI Express lane 0 + Transmit PCI Express lane 0 - Transmit Power Ground LVDS_A_DATA0_P | LVDS Channel A LVDS_A_DATA0_N | LVDS Channel A LVDS_A_DATA1_P | LVDS Channel A LVDS_A_DATA1_N | LVDS Channel A LVDS_A_DATA2_P| LVDS Channel A LVDS_A_DATA2_N | LVDS Channel A Data2 LVDS_VDD_EN | LVDS Panel Power Control LVDS_A_DATA3_P | LVDS Channel A LVDS_A_DATA3_N | LVDS Channel A Power Ground LVDS_A_CLK_P | LVDS Channel A Clock+ LVDS_A_CLK_N | LVDS Channel A ClockLVDS_DDC_CLK | JILI I2C Clock LVDS_DDC_DATA | JILI I2C Data EXT_GPI3 | General Purpose Input 3 KBD_RST# | Keyboard Reset KBD_A20GATE CLK_PCIE_CON_P CLK_PCIE_CON_N Power Ground n.c. n.c. EXT_GPO0 | General Purpose Output 0 n.c. n.c. Power Ground 12V VCC 12V VCC 12V VCC Power Ground 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC Power Ground DP-O PWR DP-O DP-O PWR DP-O DP-O I-3,3 DP-O DP-O PWR I-3,3 DP-O DP-O PWR DP-O DP-O DP-O DP-O DP-O DP-O O-3,3 DP-O DP-O PWR DP-O DP-O I/O-3,3 I/O-3,3 I-3,3 I-3,3 I-3,3 DP-O DP-O PWR Nc Nc O-3,3 Nc Nc PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR Termination PU 10k 3,3V (S0) PU 10k 3,3V (S0) PD 100k PU 2k21 3,3V (s0) PU 2k21 3,3V (s0) PU 10k 3,3V (S0) PU 10k 3,3V (S0) PU 10k 3,3V (S0) PD 10k - [ Power | LVDS | PCIe ] Comment - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 22 4 Connector Pinouts Connector X1A (Signal Levels B1-B55) Pin B1-B55 Pin Signal B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 Note: GND GBE0_ACT LPC_FRAME# LPC_AD0 LPC_AD1 LPC_AD2 LPC_AD3 LPC_DRQ0# LPC_DRQ1# LPC_CLK GND PWRBTN# SMB_CK SMB_DAT SMB_ALERT# SATA1_TX+ SATA1_TXSUS_STAT# SATA1_RX+ SATA1_RXGND SATA3_TX+ SATA3_TXPWR_OK SATA3_RX+ SATA3_RXWDT AC_SDIN2 AC_SDIN1 AC_SDIN0 GND SPKR I2C_CK I2C_DAT THRM# USB7USB7+ USB_4_5_OC# USB5USB5+ GND USB3USB3+ USB_0_1_OC# USB1USB1+ EXCD1_PERST# EXCD1_CPPE# SYS_RESET# CB_RESET# GND PCIE_RX5+ PCIE_RX5GPO1 PCIE_RX4+ [ LAN | Power | USB | SATA | PCIe | AUDIO | LPC] Type Termination Comment Description Power Ground GBE0_ACT# | Ethernet Activity LED LPC_FRAME# | LPC Frame Indicator LPC_AD0 | LPC Adress & DATA Bus LPC_AD1 | LPC Adress & DATA Bus LPC_AD2 | LPC Adress & DATA Bus LPC_AD3 | LPC Adress & DATA Bus LPC_DRQ#0 | LPC Request 0 LPC_DRQ#1 | LPC Request 1 CLK_LPC_33M_EXT |33MHz LPC clock Power Ground EXT_PWRBTN# | Power Button SMB_CLK_EXT | SMBUS Clock SMB_DATA_EXT | SMBUS Data SMB_ALERT# | SMBUS Interrupt SATA_TX1_P | SATA 1 Transmit Data + SATA_TX1_N | SATA 1 Transmit Data PM_SUS_ STAT# SATA_RX1_P | SATA 1 Receive Data + SATA_RX1_N | SATA 1 Receive Data Power Ground SATA_TX3_P | SATA 3 Transmit Data + SATA_TX3_N | SATA 3 Transmit Data EXT_PWR_OK | Power OK SATA_RX3_P | SATA 3 Receive Data + SATA_RX3_N | SATA 3 Receive Data WDT | Watch Dog Timer HDA_SDIN2_ICH| HD Audio Serial Input HDA_SDIN1_ICH| HD Audio Serial Input HDA_SDIN0_ICH| HD Audio Serial Input Power Ground HDA_SPKR | Speaker I2C_CLK_EXT | I2C clock I2C_DATA_EXT | I2C data PM_THRM# | Over Temperature USB7_N | USB Data – Port7 USB7_P | USB Data + Port7 USB_45_OC# | USB OverCurrent Port 4/5 USB5_N | USB Data – Port5 USB5_P | USB Data + Port5 Power Ground USB3_N | USB Data – Port3 USB3_P | USB Data + Port3 USB_01_OC# | USB OverCurrent Port 0/1 USB1_N | USB Data – Port1 USB1_P | USB Data + Port1 EXCD1_PERST# | Express card reset EXCD1_CPPE# | capable c. request EXT_SYS_RESET# | Reset Input CB_RESET# | Carrier board Reset Power Ground opt. PCI Express lane 5 + Recieve opt. PCI Express lane 5 - Recieve EXT_GPO1 | General Purpose Output 1 PCI Express lane 4 + Recieve PWR OD I-3,3 I/O-3,3 I/O-3,3 I/O-3,3 I/O-3,3 I-3,3 I-3,3 O-3,3 PWR I-3,3 O-3,3 IO-3,3 IO-3,3 DP-O DP-O O-3,3 DP-I DP-I PWR DP-O DP-O I-3,3 DP-I DP-I O-3,3 I-3,3 I-3,3 I-3,3 PWR O-3,3 O-3,3 I/O-3,3 O-3,3 DP-I/O DP-I/O I-3,3 DP-I/O DP-I/O PWR DP-I/O DP-I/O I-3,3 DP-I/O DP-I/O O-3,3 I-3,3 I-3,3 O-3,3 PWR Nc Nc O-3,3 DP-I PU 10k 3,3V PU 10k 3,3V PU 20k 3,3V PU 2k2 3,3V PU 2k2 3,3V PU 1k0 3,3V PU 2k21 3,3V PU 2k21 3,3V PU 8k25 3,3V PU 10k 3,3V PU 10k 3,3V PU 10k 3,3V PU 10k 3,3V PD 10k - int. PU 20k in ICH9 int. PU 20k in ICH9 int. PU 20k in ICH9 int. PU 20k in ICH9 int. PU 20k in ICH9 int. PU 20k in ICH10 int. PD 20k in ICH9 int. PD 20k in ICH9 int. PD 20k in ICH9 int. PD 20k in ICH9 int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V int. PD 15k in ICH9 | 5V just available if no just available if no availlable when ICH9-MDH or The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 23 4 Connector Pinouts Connector X1A (Signal Levels B56-B110) Pin B56-B110 Pin Signal B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 B83 B84 B85 B86 B87 B88 B89 B90 B91 B92 B93 B94 B95 B96 B97 B98 B99 B100 B101 B102 B103 B104 B105 B106 B107 B108 B109 B110 Note: PCIE_RX4GPO2 PCIE_RX3+ PCIE_RX3GND PCIE_RX2+ PCIE_RX2GPO3 PCIE_RX1+ PCIE_RX1WAKE0# WAKE1# PCIE_RX0+ PCIE_RX0GND LVDS_B0+ LVDS_B0LVDS_B1+ LVDS_B1LVDS_B2+ LVDS_B2LVDS_B3+ LVDS_B3LVDS_BKLT_EN GND LVDS_B_CK+ LVDS_B_CKLVDS_BKLT_CTRL VCC_5V_SBY VCC_5V_SBY VCC_5V_SBY VCC_5V_SBY RSVD VGA_RED GND VGA_GRN VGA_BLU VGA_HSYNC VGA_VSYNC VGA_I2C_CK VGA_I2C_DAT TV_DAC_A TV_DAC_B TV_DAC_C GND VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V GND Description Type PCI Express lane 4 - Recieve EXT_GPO2 | General Purpose Output 2 PCI Express lane 3 + Recieve PCI Express lane 3 - Recieve Power Ground PCI Express lane 2 + Recieve PCI Express lane 2 - Recieve EXT_GPO3 | General Purpose Output 3 PCI Express lane 1 + Recieve PCI Express lane 1 - Recieve PCIE_WAKE# WAKE1# PCI Express lane 0 + Recieve PCI Express lane 0 - Recieve Power Ground LVDS_B_DATA0_P | LVDS Channel B Data0+ LVDS_B_DATA0_N | LVDS Channel B Data0LVDS_B_DATA1_P | LVDS Channel B Data1+ LVDS_B_DATA1_N | LVDS Channel B Data1LVDS_B_DATA2_P| LVDS Channel B Data2+ LVDS_B_DATA2_N | LVDS Channel B Data2 LVDS_B_DATA3_P | LVDS Channel B Data3+ LVDS_B_DATA3_N | LVDS Channel B Data3LVDS_BKLT_CTRL | Panel Backlight ON Power Ground LVDS_B_CLK_P | LVDS Channel B Clock+ LVDS_B_CLK_N | LVDS Channel B ClockLVDS_BKLT_CTRL | Backlight Brightness +V_STBY_ETX | 5V Standby +V_STBY_ETX | 5V Standby +V_STBY_ETX | 5V Standby +V_STBY_ETX | 5V Standby n.c. CRT_RED | Analog Video RGB-RED Power Ground CRT_GREEN | Analog Video RGB-GREEN CRT_BLUE | Analog Video RGB-BLUE CRT_HSYNC | Analog Video H-Sync CRT_VSYNC | Analog Video V-Sync CRT_DDC_CLK | Display Data Channel Clock CRT_DDC_DATA | Display Data Channel Data TV_DACA_CVBS | Composite CVBS TV_DADB_Y | TV Luminance Signal TV_DADC_C | TV Chrominance Signal Power Ground 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC Power Ground DP-I O-3,3 DP-I DP-I PWR DP-I DP-I O-3,3 DP-I DP-I IO-3,3 I-3,3 DP-I DP-I PWR DP-O DP-O DP-O DP-O DP-O DP-O DP-O DP-O O-3,3 PWR DP-O DP-O O-3,3 PWR 5V PWR 5V PWR 5V PWR 5V nc OA PWR OA OA O-3,3 O-3,3 I/O-5 I/O-5 OA OA OA PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR [ Power | PCIe | LVDS | CRT,TV] Termination Comment PD 10k PD 10k PU 1k0 3,3V PU 10k 3,3V PD 100k PD 150R PD 150R PD 150R PU 2k21 5V (S0) PU 2k21 5V (S0) PD 150R PD 150R PD 150R - availlable when ICH9-MDH or availlable when ICH9-MDH or availlable when ICH9-MDH or - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 24 4 Connector Pinouts 4.4 Connector X1B Connector X1B (Signal Levels C1-C55) Pin C1-C55 Pin Signal C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 Note: GND IDE_D7 IDE_D6 IDE_D3 IDE_D15 IDE_D8 IDE_D9 IDE_D2 IDE_D13 IDE_D1 GND IDE_D14 IDE_IORDY IDE_IOR# PCI_PME# PCI_GNT2# PCI_REQ2# PCI_GNT1# PCI_REQ1# PCI_GNT0# GND PCI_REQ0# PCI_RST# PCI_AD0 PCI_AD2 PCI_AD4 PCI_AD6 PCI_AD8 PCI_AD10 PCI_AD12 GND PCI_AD14 PCI_C/BE1# PCI_PERR# PCI_LOCK# PCI_DEVSEL# PCI_IRDY# PCI_C/BE2# PCI_AD17 PCI_AD19 GND PCI_AD21 PCI_AD23 PCI_C/BE3# PCI_AD25 PCI_AD27 PCI_AD29 PCI_AD31 PCI_IRQA# PCI_IRQB# GND PEG_RX0+ PEG_RX0TYPE0# PEG_RX1+ [ IDE | Power | USB | SATA | PCIe | AUDIO] Type Termination Comment Description Power Ground IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus Power Ground IDE Data Bus IDE I/O Ready IDE I/O Read PCI Power Management Event PCI Bus Grant 2 PCI Bus Request 2 PCI Bus Grant 1 PCI Bus Request 1 PCI Bus Grant 0 Power Ground PCI Bus Reqest 0 PCI Bus Reset PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line Power Ground PCI Adress & Data Bus line PCI Bus Command and Byte enables 1 PCI Bus Grant Error PCI Bus Lock PCI Bus Device Select PCI Bus Bus Initiator Ready PCI Bus Command and Byte enables 2 PCI Adress & Data Bus line PCI Adress & Data Bus line Power Ground PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Bus Command and Byte enables 3 PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Bus Interrupt Request A PCI Bus Interrupt Request B Power Ground PCIexpress Graphics Recieve + (0) PCIexpress Graphics Recieve - (0) n.c. for type 2 module PCIexpress Graphics Recieve + (1) PWR I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T PWR I/O-5T I/O-5T I/O-3,3 I/O-3,3 O-3,3 I-5T O-3,3 I-5T O-3,3 PWR I-5T O-3,3 I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T PWR I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T PWR I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I-5T I-5T PWR DP-I DP-I nc DP-I PD 10k PU 4k7 3,3V (S0) PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) PD 1k0 PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) PU 8k2 3,3V (S0) - int. PU 20k in ICH9 int. PU 20k in ICH9 (if int. PU 20k in ICH9 (if int. PU 20k in ICH9 (if - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 25 4 Connector Pinouts Connector X1B (Signal Levels C56-C110) Pin C56-C110 Pin Signal C56 C57 C58 C59 C60 C61 C62 C63 C64 C65 C66 C67 C68 C69 C70 C71 C72 C73 C74 C75 C76 C77 C78 C79 C80 C81 C82 C83 C84 C85 C86 C87 C88 C89 C90 C91 C92 C93 C94 C95 C96 C97 C98 C99 C100 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 Note: PEG_RX1TYPE1# PEG_RX2+ PEG_RX2GND PEG_RX3+ PEG_RX3RSVD RSVD PEG_RX4+ PEG_RX4RSVD PEG_RX5+ PEG_RX5GND PEG_RX6+ PEG_RX6SDVO_DATA PEG_RX7+ PEG_RX7GND RSVD PEG_RX8+ PEG_RX8GND PEG_RX9+ PEG_RX9RSVD GND PEG_RX10+ PEG_RX10GND PEG_RX11+ PEG_RX11GND PEG_RX12+ PEG_RX12GND PEG_RX13+ PEG_RX13GND RSVD PEG_RX14+ PEG_RX14GND PEG_RX15+ PEG_RX15GND VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V GND Description Type PCIexpress Graphics Recieve - (1) n.c. for type 2 module PCIexpress Graphics Recieve + (2) PCIexpress Graphics Recieve - (2) Power Ground PCIexpress Graphics Recieve + (3) PCIexpress Graphics Recieve - (3) n.c. n.c. PCIexpress Graphics Recieve + (4) PCIexpress Graphics Recieve - (4) n.c. PCIexpress Graphics Recieve + (5) PCIexpress Graphics Recieve - (5) Power Ground PCIexpress Graphics Recieve + (6) PCIexpress Graphics Recieve - (6) SDVO_CTRLDATA PCIexpress Graphics Recieve + (7) PCIexpress Graphics Recieve - (7) Power Ground n.c. PCIexpress Graphics Recieve + (8) PCIexpress Graphics Recieve - (8) Power Ground PCIexpress Graphics Recieve + (9) PCIexpress Graphics Recieve - (9) n.c. Power Ground PCIexpress Graphics Recieve + (10) PCIexpress Graphics Recieve - (10) Power Ground PCIexpress Graphics Recieve + (11) PCIexpress Graphics Recieve – (11) Power Ground PCIexpress Graphics Recieve + (12) PCIexpress Graphics Recieve - (12) Power Ground PCIexpress Graphics Recieve + (13) PCIexpress Graphics Recieve - (13) Power Ground n.c. PCIexpress Graphics Recieve + (14) PCIexpress Graphics Recieve - (14) Power Ground PCIexpress Graphics Recieve + (15) PCIexpress Graphics Recieve - (15) Power Ground 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC Power Ground DP-I nc DP-I DP-I PWR DP-I DP-I nc nc DP-I DP-I nc DP-I DP-I PWR DP-I DP-I I/O-3,3 DP-I DP-I PWR nc DP-I DP-I PWR DP-I DP-I nc PWR DP-I DP-I PWR DP-I DP-I PWR DP-I DP-I PWR DP-I DP-I PWR nc DP-I DP-I PWR DP-I DP-I PWR PWR PWR PWR PWR PWR PWR PWR Termination - [ Power | LVDS | PCIe ] Comment opt. PU 2k21 3,3V (S0) = - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 26 4 Connector Pinouts Connector X1B (Signal Levels D1-D55) Pin D1-D55 Pin Signal D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 D32 D33 D34 D35 D36 D37 D38 D39 D40 D41 D42 D43 D44 D45 D46 D47 D48 D49 D50 D51 D52 D53 D54 D55 Note: GND IDE_D5 IDE_D10 IDE_D11 IDE_D12 IDE_D4 IDE_D0 IDE_REQ IDE_IOW# IDE_ACK# GND IDE_IRQ IDE_A0 IDE_A1 IDE_A2 IDE_CS1# IDE_CS3# IDE_RESET# PCI_GNT3# PCI_REQ3# GND PCI_AD1 PCI_AD3 PCI_AD5 PCI_AD7 PCI_C/BE0# PCI_AD9 PCI_AD11 PCI_AD13 PCI_AD15 GND PCI_PAR PCI_SERR# PCI_STOP# PCI_TRDY# PCI_FRAME# PCI_AD16 PCI_AD18 PCI_AD20 PCI_AD22 GND PCI_AD24 PCI_AD26 PCI_AD28 PCI_AD30 PCI_IRQC# PCI_IRQD# PCI_CLKRUN# PCI_M66EN PCI_CLK GND PEG_TX0+ PEG_TX0PEG_LANE_RV# PEG_TX1+ [ IDE | Power | USB | SATA | PCIe | AUDIO | LPC] Type Termination Comment Description Power Ground IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE Data Bus IDE IO Write IDE DMA Acknowledge Power Ground IDE Interrupt Request IDE Adress Bus IDE Adress Bus IDE Adress Bus IDE Chip Select Channel 0 IDE Chip Select Channel 1 IDE Hard Drive Reset PCI Bus Grant 3 PCI Bus Reqest 0 Power Ground PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Bus Command and Byte enables 0 PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line Power Ground PCI Bus Parity PCI Bus System Error PCI Bus Stop PCI Bus Target Ready PCI Bus Cycle Frame PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line Power Ground PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Adress & Data Bus line PCI Bus Interrupt Request C PCI Bus Interrupt Request D PCI Clock Run n.c. CLK_PCI_33M_EXT | PCI Clock 33MHz Power Ground PCIexpress Graphics Transmit + (0) PCIexpress Graphics Transmit - (0) PCIexpress Graphics Lane Reversal PCIexpress Graphics Transmit + (1) PWR I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T O-3,3 O-3,3 PWR I-5T O-3,3 O-3,3 O-3,3 O-3,3 O-3,3 O-3,3 O-3,3 I-5T PWR I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T PWR I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T I/O-5T PWR I/O-5T I/O-5T I/O-5T I/O-5T I-5T I-5T I-5T nc O-3,3 PWR DP-O DP-O I-3,3 DP-O PD 5k62 PD 10k PU 8k2 3,3V PU 8k2 3,3V PU 8k2 3,3V PU 8k2 3,3V PU 8k2 3,3V PU 8k2 3,3V PU 8k2 3,3V PU 8k25 3,3V - int. PU 31k in PATA bridge | int. PU 20k in ICH9 (if - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 27 4 Connector Pinouts Connector X1B (Signal Levels D56-D110) Pin D56-D110 Pin Signal D56 D57 D58 D59 D60 D61 D62 D63 D64 D65 D66 D67 D68 D69 D70 D71 D72 D73 D74 D75 D76 D77 D78 D79 D80 D81 D82 D83 D84 D85 D86 D87 D88 D89 D90 D91 D92 D93 D94 D95 D96 D97 D98 D99 D100 D101 D102 D103 D104 D105 D106 D107 D108 D109 D110 Note: PEG_TX1TYPE2# PEG_TX2+ PEG_TX2GND PEG_TX3+ PEG_TX3RSVD RSVD PEG_TX4+ PEG_TX4GND PEG_TX5+ PEG_TX5GND PEG_TX6+ PEG_TX6SDVO_CLK PEG_TX7+ PEG_TX7GND IDE_CBLID PEG_TX8+ PEG_TX8GND PEG_TX9+ PEG_TX9RSVD GND PEG_TX10+ PEG_TX10GND PEG_TX11+ PEG_TX11GND PEG_TX12+ PEG_TX12GND PEG_TX13+ PEG_TX13GND PEG_ENABLE# PEG_TX14+ PEG_TX14GND PEG_TX15+ PEG_TX15GND VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V VCC_12V GND [ IDE | Power | USB | SATA | PCIe | AUDIO | LPC] Type Termination Comment Description PCIexpress Graphics Transmit - (1) n.c. for type 2 module PCIexpress Graphics Transmit + (2) PCIexpress Graphics Transmit - (2) Power Ground PCIexpress Graphics Transmit + (3) PCIexpress Graphics Transmit - (3) PCIexpress Graphics Transmit + (4) PCIexpress Graphics Transmit - (4) Power Ground PCIexpress Graphics Transmit + (5) PCIexpress Graphics Transmit - (5) Power Ground PCIexpress Graphics Transmit + (6) PCIexpress Graphics Transmit - (6) SDVO_CTRLCLK PCIexpress Graphics Transmit + (7) PCIexpress Graphics Transmit - (7) Power Ground IDE_CBLID# | IDE cable type detect PCIexpress Graphics Transmit + (8) PCIexpress Graphics Transmit - (8) Power Ground PCIexpress Graphics Transmit + (9) PCIexpress Graphics Transmit - (9) n.c. Power Ground PCIexpress Graphics Transmit + (10) PCIexpress Graphics Transmit - (10) Power Ground PCIexpress Graphics Transmit + (11) PCIexpress Graphics Transmit - (11) Power Ground PCIexpress Graphics Transmit + (12) PCIexpress Graphics Transmit - (12) Power Ground PCIexpress Graphics Transmit + (13) PCIexpress Graphics Transmit - (13) Power Ground PCIexpress Graphics Enable PCIexpress Graphics Transmit + (14) PCIexpress Graphics Transmit - (14) Power Ground PCIexpress Graphics Transmit + (15) PCIexpress Graphics Transmit - (15) Power Ground 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC Power Ground DP-O nc DP-O DP-O PWR DP-O DP-O nc nc DP-O DP-O PWR DP-O DP-O PWR DP-O DP-O IO-3,3 DP-O DP-O PWR I/0-3,3 DP-O DP-O PWR DP-O DP-O nc PWR DP-O DP-O PWR DP-O DP-O PWR DP-O DP-O PWR DP-O DP-O PWR I-3,3 DP-O DP-O PWR DP-O DP-O PWR PWR PWR PWR PWR PWR PWR PWR PU 10k 3,3V - - opt. int. PU in IDE flash - The termination resistors in this table are already mounted on the ETXexpress® board. Refer to the design guide for information about additional termination resistors. Kontron User's Guide ETXexpress®-PC 28 4 Connector Pinouts 4.5 Pin Nr. D61 D62 D58 D59 D55 D56 D52 D53 C61 D74 D75 D71 D72 D68 D69 D65 D66 C74 4.6 Pin Nr. D61 D62 D58 D59 D55 D56 D52 D53 C61 C58 C59 D74 D75 D71 D72 D68 D69 D65 D66 C74 C71 C72 Alternative pinout of HDMI Pin Name PCIexpress PCIexpress Graphics Transmit + 3 PCIexpress Graphics Transmit - 3 PCIexpress Graphics Transmit + 2 PCIexpress Graphics Transmit - 2 PCIexpress Graphics Transmit + 1 PCIexpress Graphics Transmit - 1 PCIexpress Graphics Transmit + 0 PCIexpress Graphics Transmit - 0 PCIexpress Graphics Receive + 3 PCIexpress Graphics Transmit + 7 PCIexpress Graphics Transmit – 7 PCIexpress Graphics Transmit + 6 PCIexpress Graphics Transmit – 6 PCIexpress Graphics Transmit + 5 PCIexpress Graphics Transmit – 5 PCIexpress Graphics Transmit + 4 PCIexpress Graphics Transmit – 4 PCIexpress Graphics Receive + 7 Pin Name HDMI TMDS_B_CLK TMDS_B_CLK# TMDS_B_DATA0 TMDS_B_DATA0# TMDS_B_DATA1 TMDS_B_DATA1# TMDS_B_DATA2 TMDS_B_DATA2# TMDS_B_HPD# TMDS_C_CLK TMDS_C_CLK# TMDS_C_DATA0 TMDS_C_DATA0# TMDS_C_DATA1 TMDS_C_DATA1# TMDS_C_DATA2 TMDS_C_DATA2# TMDS_C_HDP# HDMI Pin Description HDMI Port B Clock HDMI port B Clock complement HDMI port B Data0 HDMI port B Data0 complement HDMI port B Data1 HDMI port B Data1 complement HDMI port B Data2 HDMI port B Data2 complement HDMI port B Hot-plug detect HDMI port C Clock HDMI port C Clock complement HDMI port C Data0 HDMI port C Data0 complement HDMI port C Data1 HDMI port C Data1 complement HDMI port C Data2 HDMI port C Data2 complement HDMI port C Hot-plug detect Alternative Pinout of Display Port Pin Name PCIexpress PCIexpress Graphics Transmit + 3 PCIexpress Graphics Transmit – 3 PCIexpress Graphics Transmit + 2 PCIexpress Graphics Transmit – 2 PCIexpress Graphics Transmit + 1 PCIexpress Graphics Transmit - 1 PCIexpress Graphics Transmit + 0 PCIexpress Graphics Transmit – 0 PCIexpress Graphics Receive + 3 PCIexpress Graphics Receive + 2 PCIexpress Graphics Receive – 2 PCIexpress Graphics Transmit + 7 PCIexpress Graphics Transmit – 7 PCIexpress Graphics Transmit + 6 PCIexpress Graphics Transmit – 6 PCIexpress Graphics Transmit + 5 PCIexpress Graphics Transmit – 5 PCIexpress Graphics Transmit + 4 PCIexpress Graphics Transmit – 4 PCIexpress Graphics Receive + 7 PCIexpress Graphics Receive + 6 PCIexpress Graphics Receive – 6 Kontron User's Guide ETXexpress®-PC Pin Name HDMI DPB_LANE3 DPB_LANE3# DPB_LANE2 DPB_LANE2# DPB_LANE1 DPB_LANE1# DPB_LANE0 DPB_LANE0# DPB_HPD# DPB_AUX DPB_AUX# DPC_LANE3 DPC_LANE3# DPC_LANE2 DPC_LANE2# DPC_LANE1 DPC_LANE1# DPC_LANE0 DPC_LANE0# DPC_HPD# DPC_AUX DPC_AUX# 29 HDMI Pin Description Displayport B Lane3 Displayport B Lane3 complement Displayport B Lane2 Displayport B Lane2 complement Displayport B Lane1 Displayport B Lane1 complement Displayport B Lane0 Displayport B Lane0 complement Displayport B Hot-plug detect Displayport B Aux Displayport B Aux complement Displayport C Lane3 Displayport C Lane3 complement Displayport C Lane2 Displayport C Lane2 complement Displayport C Lane1 Displayport C Lane1 complement Displayport C Lane0 Displayport C Lane0 complement Displayport C Hot-plug detect Displayport C Aux Displayport C Aus complement 4 Connector Pinouts D88 D89 D85 D86 D81 D82 D78 D77 C88 C85 C86 PCIexpress Graphics Transmit + 11 PCIexpress Graphics Transmit – 11 PCIexpress Graphics Transmit + 10 PCIexpress Graphics Transmit – 10 PCIexpress Graphics Transmit + 9 PCIexpress Graphics Transmit – 9 PCIexpress Graphics Transmit + 8 PCIexpress Graphics Transmit – 8 PCIexpress Graphics Receive + 11 PCIexpress Graphics Receive + 10 PCIexpress Graphics Receive – 10 4.7 Signal Description 4.7.1 PCIexpress x1 lanes DPD_LANE3 DPD_LANE3# DPD_LANE2 DPD_LANE2# DPD_LANE1 DPD_LANE1# DPD_LANE0 DPD_LANE0# DPD_HPD# DPD_AUX DPD_AUX# Displayport D Lane3 Displayport D Lane3 complement Displayport D Lane2 Displayport D Lane2 complement Displayport D Lane1 Displayport D Lane1 complement Displayport D Lane0 Displayport D Lane0 complement Displayport D Hot-plug detect Displayport D Aux Displayport D Aus complement The PCI express x1 lanes is a fast connection interface for many different system devices, such as network controllers, I/O controllers or express card devices. The implementation of this subsystem complies with the ETXexpress® / COMexpress Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.2 USB Eight USB ports (EHCI high-speed 2.0 controller) are on the Intel® ICH-9M south bridge device available. The USB controllers comply with both versions 1.1 and 2.0 of the USB standard and are backward compatible. Configuration The USB controllers are PCI bus devices. The BIOS allocates required system resources during configuration of the PCI bus. 4.7.3 SATA The Intel® ICH-9M south bridge device offers the possibility to connect 4 SATA Harddisks according SATA with 150 MB/s per channel or SATA II with 300 MB/s per channel in AHCI mode. Configuration The SATA controller is a PCI bus device. The BIOS allocates required system resources during configuration of the PCI bus. 4.7.4 Audio The ETXexpress®-PC PCI HD audio controller is integrated in the Intel® ICH-9 Southbridge. Kontron User's Guide ETXexpress®-PC 30 4 Connector Pinouts Configuration The audio controller is a PCI bus device. The BIOS allocates required system resources during configuration of the PCI device. 4.7.5 Serial IRQ The serial IRQ pin offers a standardized interface to link interrupt request lines to a single wire. Configuration The serial IRQ machine is in “Continuous Mode” 4.7.6 VGA Output The ETXexpress®-PC graphics subsystem is integrated in the Intel® GS45 northbridge. Configuration The graphics controller requires the following resources: ® An IRQ ® Several I/O addresses ® Memory-address blocks in high memory The BIOS allocates the resources during AGP configuration. Many resources are set for compatibility with industry-standard settings. 4.7.7 LVDS Flat Panel Interface (JILI) The user interface for flat panels is the JUMPtec Intelligent LVDS Interface (JILI). The implementation of this subsystem complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.8 PCIexpress Graphics The PCI express Graphics interface allows the connection of high performace graphics chips on an high bandwidth interface. The implementation of this subsystem complies with the ETXexpress® / COMexpress Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.9 SDVO The ETXexpress®-CD Serial Digital Video Output port is integrated in the Intel® GS45 northbridge. It has the following features: ® Share its pins with the PEG interface Kontron User's Guide ETXexpress®-PC 31 4 Connector Pinouts ® Serial Digital Video Out Port (DVOB & DVOC) support ® Two 12-bit channels ® The SDVO B/C ports can drive a variety of SDVO devices (TV-Out Encoders, TMDS and LVDS transmitters, etc.) The implementation of this subsystem complies with the ETXexpress® / COMexpress Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.10 HDMI There is one HDMI port available shared together with PCIexpress Graphics, SDVO and Displayport. 4.7.11 Displayport The display port is available shared together with PCIexpress Graphics, SDVO and HDMI. 4.7.12 Ethernet The Ethernet interface offers 10 Mbit, 100Mbit or 1Gbit connection and is driven by the Intel® 82567 PCIexpress Gbit Ethernet controller. Configuration The Ethernet controller is a PCIexpress bus device. The BIOS allocates required system resources during configuration of the PCIexpress device. 4.7.13 Power Control Power Good / Reset Input The ETXexpress®-PC provides an external input for a power-good signal or a manual- reset pushbutton. The implementation of this subsystem complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.14 Power Management ATX PS Control The ETXexpress®-PC can control the main power output of an ATX-style power supply. The implementation of this subsystem complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. External SMI Interrupt Contact Kontron Embedded Modules technical support for information on this feature. Kontron User's Guide ETXexpress®-PC 32 4 Connector Pinouts 4.7.15 Miscellaneous Circuits Speaker The implementation of the speaker output complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. Battery The implementation of the battery input complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. In compliance with EN60950, there are at least two current-limiting devices (resistor and diode) between the battery and the consuming component. I2C Bus The I2C Bus is implemented by using GPIOs from the southbridge. You also can access the I2C Bus via JUMPtec’s Intelligent Device Architecture (JIDA) BIOS functions. For additional information, refer to the ETXexpress® Design Guide, I2C application notes and JIDA specifications which are available at the Kontron Web site. SM Bus System Management (SM) bus signals are connected to the SM bus controller, which is located in the Intel® ICH-9M device. For more information about the SM bus, please see the System Management (SM) Bus section in the Appendix A: System Resources chapter. LPC Bus The Low Pin Count Interface signals are connected to the LPC Bus bridge, which is located in the Intel® ICH-9M. The LPC low speed interface can be used for peripheral circuits such as an external Super I/O Controller, which typically combine legacy-device support into a single IC. The implementation of this subsystem complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.16 PCI Bus The implementation of this subsystem complies with the ETXexpress® / COMexpress Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to the documentation for additional information. 4.7.17 IDE Port The IDE host adapter is capable of DMA-33/66/100 operation. The implementation of this subsystem complies with the ETXexpress® Specification. Implementation information is provided in the ETXexpress® Design Guide. Refer to those documents for additional information. Kontron User's Guide ETXexpress®-PC 33 4 Connector Pinouts Configuration The IDE host adapter is a USB to IDE converter. It is configured by the BIOS during PCI device configuration. You can disable it in setup. Resources used by the USB/IDE host adapter are compatible with the PC/AT. Warning: Current Operating Systems have problems or cannot be installed on an IDE device connected to an USB to IDE converter. Therefore the devices connected to this device must be seen as mass storage device and not as bootable or installable device Kontron User's Guide ETXexpress®-PC 34 5 Special Features 5 Special Features 5.1 Watchdog Timer This feature is implemented in a watchdog PIC. You can configure the Watchdog Timer (WDT) in BIOS setup to start after a set amount of time after power-on boot. The WDT can also be controlled by the JIDA32 Library API (Refer to Appendix F: JIDA Standard). The application software should strobe the WDT to prevent its timeout. Upon timeout, the WDT resets and restarts the system. This provides a way to recover from program crashes or lockups. Configuration You can program the timeout period for the watchdog timer in two ranges: ® 1-second increments from 1 to 255 seconds ® 1-minute increments from 1 to 255 minutes Contact Kontron Embedded Modules technical support for information on programming and operating the WDT. 5.2 General Purpose Input and Output ETXexpress®-PC offers 4 General Purpose Input (GPI) pins and 4 General Purpose Output (GPO) pins. On a 3.3V level digital in- and outputs are available. Signal GPI0 GPI1 GPI2 GPI3 GPO0 GPO1 GPO2 GPO3 Pin A54 A63 A67 A85 A93 B54 B57 B63 Description General Purpose Input 0 General Purpose Input 1 General Purpose Input 2 General Purpose Input 3 General Purpose Output 0 General Purpose Output 1 General Purpose Output 2 General Purpose Output 3 Configuration The GPI and GPO pins can be configured via JIDA32. Please refer to the JIDA32 manual in the driver download packet on our website. Kontron User's Guide ETXexpress®-PC 35 5 Special Features 5.3 Usage of Different Graphic interfaces 5.3.1 Available Graphic interfaces The ETXexpress®-PC offers VGA, PCIexpress, LVDS, HDMI, SDVO and Displayport interfaces to connect graphical user interfaces. The usage of VGA, PCIexpress and SDVO complies with the current ETXexpress® Specification. The principle of using them is shown in the next drawing. VGA and LVDS interface is always available and can be used. The pins of PCIexpress Graphics either are used as PCIexpress Graphics or as HDMI/SDVO/DP, which is controlled by switch1. Switch1 is the SDVO_SDA# line (C73). When this signal is high (2.5V) the SDVO/HDMI/DP output is enabled. Otherwise the lines can be used as PCIexpressGraphic. The switch 2 to select HDMI, SDVO or Displayport consists of the devices detected on the regarding sense circuits. When there is an SDVO 2 TV/LVDS/DVI converter found on the SDVO_DATA and _CLK lines (C73; Kontron User's Guide ETXexpress®-PC 36 5 Special Features D73) then the output is switched to SDVO. When there is Displayport device found on the Displayport AUX lines (C71; C72) then it is Display port and in any other case the output is switched to HDMI. Kontron User's Guide ETXexpress®-PC 37 6 Important Information 6 Important Information 6.1 Cooling Solution With introduction of higher frequency CPUs into the embedded market the need to design more efficient cooling solutions is now a necessity. These higher frequency CPUs generate much more heat, which must be removed from the application. One solution that has become more common in the embedded market is the use of heat pipes when designing a cooling solution. Kontron Embedded Modules has designed some cooling solutions that utilize heat pipes in order to perform some tests. Although Kontron Embedded Modules designed these cooling solutions strictly for test purposes, and not as a standard ETXexpress® cooling solution, the knowledge gained from these tests is being made available to customers in the form of an application note called PM_Thermal_Guidelines_E1xx.pdf. This application note should be used as a guideline to help evaluate potential thermal designs. It can be found on Kontron’s web site at www.kontron.com on the ETXexpress® product page and in the Tech Support section. 6.2 Limitation 6.2.1 Reset Behavior Intel® defined the Reset Behavior different to former Implementations. All former Boards and Modules had a level triggered reset input. ETXexpress-PC has according to the behavior change of the Intel® chipset an edge triggered reset input. This leads to the fact that the board is not been able to keep in reset by holding down the signal. 6.2.2 Booting with a single memory module When the board boots, the implemented Management Engine from Intel® needs the memory module be equipped in channel A, i.e. the module must be mounted in the bottom socket. 6.2.3 Standby with Microsoft Vista Current (preliminary) revisions of the boards show none or not correct working standby (S3) behavior with Microsoft’s Operating System Vista. 6.2.4 12V only Current (preliminary) revisions of the boards don’t work correctly in 12V only mode 6.2.5 IDE (PATA) Current Operating Systems have problems or cannot be installed on an IDE device connected to an USB to IDE converter. Therefore the devices connected to this device must be seen as mass storage device and not as bootable or installable device. There is only one IDE device working on the IDE port, no master slave capability. Kontron User's Guide ETXexpress®-PC 38 6 Important Information 6.2.6 Passive Cooling Trip Point The BIOS setting for the Passive Cooling Trip Point doesn’t work correctly in current (preliminary) revisions. Kontron User's Guide ETXexpress®-PC 39 7 Design Considerations 7 Design Considerations 7.1 Thermal Management A heat-spreader plate assembly is available from Kontron Embedded Modules for the ETXexpress®-PC. The heat-spreader plate on top of this assembly is NOT a heat sink. It works as an ETXexpress®-standard thermal interface to use with a heat sink or other cooling device. External cooling must be provided to maintain the heat-spreader plate at proper operating temperatures. Under worst-case conditions, the cooling mechanism must maintain an ambient air and heat-spreader plate temperature of 60° C or less. The aluminum slugs and thermal pads on the underside of the heat-spreader assembly implement thermal interfaces between the heat spreader plate and the major heat-generating components on the ETXexpress®-PC. About 80 percent of the power dissipated within the module is conducted to the heatspreader plate and can be removed by the cooling solution. For 2266MHz modules, the heat dissipated into the plate ranges from 35 to 45 watts. Design a cooling solution to dissipate the heat load on a heat-spreader plate at a minimum of 45 watts to accommodate all ETXexpress®-PC modules. You can use many thermal-management solutions with the heat-spreader plates, including active and passive approaches. The optimum cooling solution varies, depending on the ETXexpress® application and environmental conditions. Please see the ETXexpress® Design Guide for further information on thermal management. Kontron User's Guide ETXexpress®-PC 40 7 Design Considerations 7.2 Heatspreader Dimensions This is the backside view of the heatspreader plat with pads marked for the heat generating components for ETXexpress®-PC Modules. Kontron User's Guide ETXexpress®-PC 41 7 Design Considerations Sideview of the heat spreader: 7.3 ETXexpress-PC onboard fan connector This section describes how to connect a fan to the connector located directly on the ETXexpress®-PC. With certain BIOS-settings it is possible to control the fan depending on the Active Trip Point temperature. The fan switches on/off depending on the adjusted Active Trip Point temperature. In order for this feature to function properly an ACPI compliant OS is necessary. 7.3.1 Location and pin-out of fan connector Kontron User's Guide ETXexpress®-PC 42 7 Design Considerations The onboard fan connector (J5) can be found at the right side opposite of the DRAM sockets and it is connected onboard according to the following schematic: Kontron User's Guide ETXexpress®-PC 43 7 Design Considerations 7.3.2 BIOS settings for fan control The Active Trip Point controls the temperature when the fan is switched on and off. 7.3.3 Electrical Characteristics VCC_in_FANCON = VCC of board, limited to 12V Imax = 0,40 A Note: The VCC_in_FANCON output is not short circuit proof. If necessary the user has to ensure that the circuit is protected externally, for example by a fuse on the backplane. Kontron User's Guide ETXexpress®-PC 44 8 System Resources 8 System Resources 8.1 Interrupt Request lines Please be aware that an ACPI OS decides itself on resource usage. The tables below show only an example distribution. In 8259 PIC mode Note: IRQ# Used For Available 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Timer 0 Keyboard Slave 8259 No No No Yes Yes Yes Yes Yes No No Yes Yes No No No No RTC SCI PS/2 Mouse FPU IDE0 IDE1 Comment Note (4) Note (3) Note (5) Note (1)(2) Note (1)(2) 1 If the “Used For” device is disabled in setup, the corresponding interrupt is available for other devices. 2 if sata controller is operating in legacy mode 3 Unavailable in Advanced Configuration and Power Interface (ACPI) mode. Used as System Control Interrupt (SCI) in ACPI mode. Currently not free in Non-ACPI mode. 4 used by legacy keyboard controller when available on carrier board. 5 used by legacy ps/2 mouse controller when available on carrier board. Kontron User's Guide ETXexpress®-PC 45 8 System Resources In APIC mode Note: IRQ# Used For Available 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Timer 0 Keyboard Slave 8259 FPU IDE0 IDE1 No No No Yes Yes Yes Yes Yes No No Yes Yes Yes No No No 16 PIRQ[A] For PCI 17 PIRQ[B] For PCI 18 PIRQ[C] For PCI 19 PIRQ[D] For PCI 20 21 22 23 PIRQ[E] PIRQ[F] PIRQ[G] PIRQ[H] No No No No RTC SCI Comment Note (4) Note (4) Note (4) Note (4) Note (4) Note (2) Note (4) Note (4) Note (4) Note (1)(3) Note (1)(3) PCI IRQ line 1 + Graphics controller + HD Audio Controller + secondary IDE Note (4) PCI IRQ line 2 + HD Audio controller Note (4) PCI IRQ line 3 + USB UCHI controller #3 + SATA (native mode) Note (4) PCI IRQ line 4 + USB UCHI controller #2 + IDE (native mode) Note (4) Lan Controller Note (4) Note (4) Note (4) USB EHCI controller, USB UCHI controller #1 Note (4) 1 If the “Used For” device is disabled in setup, the corresponding interrupt is available for other devices. 2 Unavailable in Advanced Configuration and Power Interface (ACPI) mode. Used as System Control Interrupt (SCI) in ACPI mode. Currently not free in Non-ACPI mode. 3 IRQs are available if IDE controller is either disabled in setup or if in Native IDE mode. 4 ACPI OS decides on particular IRQ usage 8.2 Direct Memory Access (DMA) Channels DMA# 0 1 2 3 4 5 6 7 Used For Cascade Kontron User's Guide ETXexpress®-PC Available No No No No No No No No 46 Comment 8 System Resources 8.3 Memory Area Upper Memory Used For Available Comment C0000h-CFFFFh D0000h-DFFFFh E0000h-EFFFFh VGA BIOS No Yes No LPC Bus or Shadow RAM 8.4 System BIOS I/O Address Map Upper Memory Used For Available Comment 400h-41Fh 4D0h-4D1h 500h-53Fh 800h-87Fh 1000h> Chipset Interrupt Controller Chipset Chipset PCI No No No No No Always used by chipset 8.5 Always used by chipset Always used by chipset Inter-IC (I2C) Bus I2C Address Used For Available Comment JIDA Bus Nr. A0h A2h JIDA-EEPROM JIDA-EEPROM No No EEPROM for CMOS Data 0 0 8.6 System Management (SM)Bus I2C Address Used For Available Comment JIDA Bus Nr. 10h 12h 14h 16h 2Eh A0h A2h D2h SMB Hoste SMART_Charger SMART_Selector SMART_Battery HW-Monitor SPD SPD Clockgenerator No No No No No No No No EEPROM for CMOS Data Only be used by a SMB Charger Only be used by a SMB Selector Only be used by a SMB Battery 1 1 1 1 1 1 1 1 8.7 JILI-I2C Bus I2C Address Used For Available Comment JIDA Bus Nr. A0h JILI-EEPROM No EEPROM for CMOS Data 2 8.8 SDVO-I2C Bus I2C Address Used For Available Comment JIDA Bus Nr. A0h DDC No Display Data 3 Kontron User's Guide ETXexpress®-PC 47 9 BIOS Operation 9 BIOS Operation The module is equipped with AMI® BIOS, which is located in an onboard SPI serial flash memory. You can update the BIOS using a Flash utility. 9.1 Determining the BIOS Version To determine the AMI® BIOS version, immediately press the Pause key on your keyboard as soon as you see the following text display in the upper left corner of your screen: AMIBIOS © 2006 American Megatrends, Inc. BIOS Date: 06/16/08 10:52:49 Ver: 08.00.14 Kontron® BIOS Version <CNTGRXXX> © Copyright 2002-2008 Kontron Embedded Modules GmbH 9.2 Setup Guide The AMIBIOS Setup Utility changes system behavior by modifying the BIOS configuration. The setup program uses a number of menus to make changes and turn features on or off. Note: Selecting incorrect values may cause system boot failure. Load setup default values to recover by pressing <F9>. 9.2.1 Start AMI® BIOS Setup Utility To start the AMI® BIOS setup utility, press <DEL> when the following string appears during bootup. Press <DEL> to enter Setup The Info Menu then appears. The Setup Screen is composed of several sections: Setup Screen Location Function Menu Bar Legend Bar Item Specific Help Window Menu Window General Help Window Top Right side Bottom Right side Top Left Center Overlay (center) Lists and selects all top level menus. Lists setup navigation keys. Help for selected item. Selection fields for current menu. Help for selected menu. Menu Bar The menu bar at the top of the window lists different menus. Use the left/right arrow keys to make a selection. Legend Bar Use the keys listed in the legend bar on the bottom to make your selections or exit the current menu. The table below describes the legend keys and their alternates. Kontron User's Guide ETXexpress®-PC 48 9 BIOS Operation Key Function <F1> or <Alt-H> <Esc> ← or → Arrow key General Help window. Exit menu. Select a menu. ↑ or ↓ Arrow key <Home> or <End> <PgUp> or <PgDn> <F9> <F10> <Enter> <Alt-R> Select fields in current menu. Move cursor to top or bottom of current window. Move cursor to next or previous page. Load the default configuration values for this menu. Save and exit. Execute command or select submenu. Refresh screen. Selecting an Item Use the ↑ or ↓ key to move the cursor to the field you want. Then use the + and – keys to select a value for that field. The Save Value commands in the Exit menu save the values displayed in all the menus. Displaying Submenus Use the ← or → key to move the cursor to the submenu you want. Then press <Enter>. A pointer () marks all submenus. Item Specific Help Window The Help window on the right side of each menu displays the Help text for the selected item. It updates as you move the cursor to each field. General Help Window Pressing <F1> or <Alt-F1> on a menu brings up the General Help window that describes the legend keys and their alternates. Press <Esc> to exit the General Help window. Kontron User's Guide ETXexpress®-PC 49 9 BIOS Operation 9.3 BIOS Setup Menus 9.3.1 Main Menu Feature System Time System Date Option [hh:mm:ss] [mm-dd-yyyy] Description <Tab>, <Shift-Tab>, or <Enter> selects field <Tab>, <Shift-Tab>, or <Enter> selects field Module Info Kontron User's Guide ETXexpress®-PC 50 9 BIOS Operation Module Component Steppings Module Software Revisions Kontron User's Guide ETXexpress®-PC 51 9 BIOS Operation Current LVDS Configuration 9.3.2 Advanced Menu Kontron User's Guide ETXexpress®-PC 52 9 BIOS Operation CPU Configuration Feature Hardware Prefetcher Adjacent Cache Line Prefetch MAX CPUID Value Limit Execute-Disable Bit Capability DTS-based Thermal Management DTS Calibration Intel ® SpeedStep™ tech Intel ® C-STATE tech Enhanced C-States Kontron User's Guide ETXexpress®-PC Option Description Enabled Disabled Enabled Disabled Enabled Disabled Disables and Enables the Hardware Prefetcher Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enables and Disables the Execute-Disable Bit Capability For UP platforms, leave it enabled Enables the MAX CPUID Value Limit. Should be disabled for Windows XP Enables and Disables the DTS-based Thermal Management Enables and Disables the DTS Calibration Enables and Disables the Speed Stepping Feature Enables and Disables the C-STATE technology Enables and Disables the Enhanced C States 53 9 BIOS Operation Miscellaneous Settings Menu Feature Option Description Restore on AC Power Loss Power Off Power On Selects the behavior of switch on process after AC Power Loss Power Up Delay Post User Delay Standby Voltage On Reset Note: Disabled 4 to 5 seconds 3 to 4 seconds 2 to 3 seconds 1 to 2 seconds None 1 Sec 2 Sec … 10 Min Auto 5V Standby Chipset Reset Power Cycle Select Delay for the Power Up Delay to allow access to setup Select which voltage is used for standby power. Chipset Reset: only edge triggered reset Power Cycle: level triggered reset Intel® changed the specification of the chipset reset which is not corresponding to the COMexpress specification anymore. Chipset Reset confirms to the Intel® chipset behaviour and is level triggered only. The board can be held in a reset state. Power Cycle allows still level triggered usage, which complies with the COMexpress specification, but creates a complete power cycle of the board. Kontron User's Guide ETXexpress®-PC 54 9 BIOS Operation Event Log Configuration MARS Interface Configuration Menu Feature Option Description MARS Disabled Auto SMB Charger SMB Manager Selects how to handle the SMB Controller, either as SMB Charger for one battery or as SMB Manager for up to two batteries Kontron User's Guide ETXexpress®-PC 55 9 BIOS Operation Watchdog Menu Feature Mode Delay Timeout Kontron User's Guide ETXexpress®-PC Option Description Disabled Reset NMI Disabled 1s 5s 10s … 30:00m 0.4s 1s 5s … 10:00m Disables or selects the mode for the Set the Delay until the timer will start Set the timeout until the watchdog has to be triggered 56 9 BIOS Operation MPS Configuration Menu Note: Currently not supported Smbios Configuration Note: Currently not supported Kontron User's Guide ETXexpress®-PC 57 9 BIOS Operation Legacy Device Configuration Menu Feature Option Description Onboard Floppy Controller Disabled Enabled Disables or Enables the floppy interface of the Winbond Super I/O controller (backplane) Floppy Drive Swap Serial Port1 Address Serial Port2 Address Parallel Port Address Parallel Port Mode Parallel Port IRQ Kontron User's Guide ETXexpress®-PC Disabled Enabled Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ 4 2E8/IRQ3 Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ 4 2E8/IRQ3 Disabled 378 278 3BC SPP Bi-Directional ECP EPP + SPP ECP + EPP IRQ7 IRQ5 Select if the 2 floppy devices are swapped Selects the Resources for COMA of the Winbond Super/O controller Selects the Resources for COMB of the Winbond Super I/O controller Selects the Resources for LPT of the Winbond Super I/O controller Selects the Mode for LPT of the Winbond Super I/O controller Selects the Resources for LPT of the Winbond Super I/O controller 58 9 BIOS Operation Baseboard Hardware Health Configuration Feature Option Description H/W Health Function Enabled Disabled Enables and disables the H/W monitor of the baseboard Winbond SuperI/O controller Kontron User's Guide ETXexpress®-PC 59 9 BIOS Operation Devices Configuration Menu Feature GbE Controller GbE LAN Boot GbE Wake Up From S5 HDA Controller SMBUS Controller Kontron User's Guide ETXexpress®-PC Option Description Enabled Disabled Disabled Enabled Disabled Enabled Disabled Enabled Enabled Disabled Configure the LAN Controller Configure the LAN boot feature (PXE) Configure if the board will wake up via WOL from S5 Disables and Enables the HDA audio controller Disables and Enables the SMBUS Controller 60 9 BIOS Operation IDE Configuration Menu Feature SATA#1 Configuration Configure SATA #1 as SATA#2 Configuration Primary IDE Master Primary IDE Slave Secondary … Fourth IDE Master Hard Disk Write Protect IDE Detect Time Out (Sec) ATA(PI) 80Pin Cable Detection Kontron User's Guide ETXexpress®-PC Option Description Enabled Disabled IDE Compatible RAID AHCI IDE Enhanced Enhanced Disabled Enables and Disables the SATA interface functional block #1 Shows the detected Device Enters the device configuration page Disabled Enabled 0 5 .. 30 35 Enables and disables the hard disk write protect (only valid in BIOS/DOS mode) Configure the SATA mode Configures the SATA interface functional block #2 Selects the time out for IDE device detection in seconds Host&Device Host Device Selects the mechanism for detecting 80pin ATA(PI) cable 61 9 BIOS Operation IDE Device Configuration Menu Feature Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer Kontron User's Guide ETXexpress®-PC Option Description No Installed Auto CD/DVD ARMD Auto Disabled Auto Disabled Auto 0 … 4 Disabled Enabled Auto Disabled Enabled Host&Device Host Device Selects the type of device connected to the system Autodetects or disables the LBA Mode Autodetects or disables the Block Mode Autodetects or selects the PIO mode Enables and disables the hard disk write protect (only valid in BIOS/DOS mode) Autodetects, enables or disables the SelfMonitoring, Analysis and Reporting Tool Selects the mechanism for detecting 80pin ATA(PI) cable 62 9 BIOS Operation Memory Controller Configuration Menu Feature DRAM Frequency Configure DRAM Timing by SPD TMRC Mode TS on DIMM Memory Hole Boot Graphic Adapter Priority Internal Graphics Mode Select Max TOLUD Gfx Low Power Mode PEG Port Kontron User's Guide ETXexpress®-PC Option Description Auto 800 MHz 1067 MHz Enabled Disabled Disabled Enabled Disabled Enabled Disabled 15-16MB IGD PCI/IGD PCI/PEG PEG/IGD PEG/PCI Selects the DRAM Frequency Selects if DRAM is configured by SPDEEPROM Enables and Disables the Thermal Memory Reference Code Feature Enables and Disables thermal sensor on DIMM Enables and Disables the extended memory hole Selects which graphiccontroller to use as primary boot device: IGD: internal graphic controller PEG: PCI express graphics PCI: PCI graphic card Disabled Enabled, 32 MB Enabled, 64 MB Enabled, 128 MB 3G Bytes 2.5G Bytes 2G Bytes Disabled Enabled Auto Disabled Enabled Selects the amount of system memory used by the internal graphics device Selects the maximum of Top of low usable DRAM Enables and disables the low power mode for the graphics device Enables, disables or auto configures the PCIexpress graphics port 63 9 BIOS Operation I/O Controller Configuration Menu Feature USB Function USB Port Configure USB 2.0 Controller Enable Lock Bit Reserve Page Route PCIE Ports 0…4 PCIE High Priority Port PCIE Port 0…5 IOxAPIC Enable Kontron User's Guide ETXexpress®-PC Option Disabled 2 USB Ports 4 USB Ports … 10 USB Ports 12 USB Ports Description 6x6 USB Ports 4x8 USB Ports Disabled Enabled Disabled Enabled Configures the chipset internal USB port configuration LPC PCI Auto Enabled Disabled Disabled Port 0 Port 1 … Port 5 Disabled Enabled Selects the Inteface for Port 80h output during POST Selects the amount of enabled USB ports Enables and Disables USB 2.0 Controller Enables Lock bit at end of POST. Only disable for debugging purposes. Selects the mode for the PCIexpress ports Selects which PCIe Port has higher priority than the others Enables and Disables the IOxAPIC function for PCIe ports 64 9 BIOS Operation AHCI Settings Menu Feature AHCI BIOS Support AHCI CD/DVD Boot Time out Option Description Enabled Disabled 0 5 … 30 35 Enables or Disables the AHCI feature for SATA Option Description Set the Boot Time out of the SATA CD/DVD devices in AHCI mode AHCI Portx Menu Feature SATA Portx S.M.A.R.T. Kontron User's Guide ETXexpress®-PC Auto Not Installed Enabled Disabled Configures the individual SATA port Enables or disables the Self-Monitoring, Analysis and Reporting Tool 65 9 BIOS Operation Video Function Configuration Menu Feature Option DVMT Mode Select DVMT Mode 128MB 256MB Max DVMT Disabled Light High CRT TV SDVO CRT+SDVO LVDS CRT+LVDS DVMT/FIXED Memory PAVP Mode Boot Display Device TV Standard TV Sub-Type HDMI DP Support HDCP Support Kontron User's Guide ETXexpress®-PC Description Configures the amount of memory for the Dynamic Video Memory Technology Configures the Protected Audio Video Path Selects the Boot Display Devices NTSC PAL SECAM SMPTE240M ITU-R television SMPTE295M SMPTE296M EIA-770.2 EIA-770.3 Depending on TV Standard Disabled Enabled Disabled Enabled Selects the regarding TV standard for TV out interface Selects the regarding TV Sub-Type Enables and disables the HDMI DP Support Enables and disables the HDCP Support 66 9 BIOS Operation Internal LVDS Configuration Menu Feature Flat Panel Mode Auto Fallback Flat Panel Type PAID/FPID Kontron User's Guide ETXexpress®-PC Option Description Auto Fixed Mode PAID FPID Disabled Fixed Mode VGA 640x480 … XGA 1024x768 SXGA 1280x1024 … WXGA 1280x800 [X] Selects the Mode for the flat panel detection Selects what happens, when there is no EEPROM detected (only in FPM: Auto) Selects the resolution of the LVDS display (only in FMP: Fixed Mode) Selects the number of the PAID/FPID 67 9 BIOS Operation Channels Color Depth Local Flat Panel Scaling Single Channel Dual Channel 18bit 24bit open LDI 24bit Centered Stretched Disabled Selects, if 1x or 2x LVDS signals are used (only in FPM: Fixed Mode) Selects the Color Depth of the connected LVDS display (only in FPM: Fixed Mode) Selects the Scaling Options for the LVDS panel (only in FPM: Fixed Mode) LVDS -> DVI ID [X] 5 = 1x18 7 = 2x18 8 = 1x24 A = 2x24 (only in FPM: Auto) Backlight Control Type None/External I2C PWM Selects the mode for Backlight Control Backlight Brightness [0…255] Selects the default setting for Backlight Brightness USB Configuration Menu Feature Legacy USB Support USB 2.0 Controller Mode Option Disabled Enabled Auto HiSpeed FullSpeed BIOS EHCI Hand-Off Disabled Enabled USB Beep Message Disabled Enabled Kontron User's Guide ETXexpress®-PC Description Enables, disables or autoselects the USB legacy support feature Configures the USB 2.0 Controller to either HiSpeed (480Mbs) or FullSpeed (12Mbs) This is a workaround for OSs without EHCI hand-off support. The EHCI ownership change should claim by EHCI driver. Enables and disables the Beep during USB device enumeration 68 9 BIOS Operation USB Mass Storage Device Configuration Menu Feature USB Mass Storage Reset Delay Emulation Type Option Description 10 Sec 20 Sec 30 Sec 40 Sec Auto Floppy Forced FDD Hard Disk CDROM Number of seconds POST waits for the USB mass storage device after start unit command Selects the emulation type for the USB Mass Storage device ACPI Configuration Menu Kontron User's Guide ETXexpress®-PC 69 9 BIOS Operation General ACPI Configuration Feature Suspend mode Repost Video on S3 Resume Kontron User's Guide ETXexpress®-PC Option S1 (POS) S3 (STR) Auto Yes No Description Selects the used suspend mode Selects, if the Video is shown directly after wake up 70 9 BIOS Operation Advanced ACPI Configuration Menu Feature Option Description ACPI Version Features ACPI v1.0 ACPI v2.0 ACPI v3.0 Selects the features regarding the ACPI specification version ACPI APIC support AMI OEMB table Headless mode Kontron User's Guide ETXexpress®-PC Enabled Disabled Enabled Disabled Enabled Disabled Disables or enables the APIC support Include OEMB table pointer to R(X)SDT pointer list Enable / Disable headless operation mode through ACPI 71 9 BIOS Operation Chipset ACPI Configuration Menu Feature Energy Lake Feature APIC ACPI SCI IRQ USB Device Wakeup from S3/S4 High Performance Event Timer HPET Memory Address range Kontron User's Guide ETXexpress®-PC Option Enabled Disabled Description Disables or enables the Energy Lake Feature of the Chipset Enabled Disabled Enabled Disabled Enabled Disabled Disables or enables the APIC SCI IRQ Controls the USB device wakeup event from S3 and S4 Disables or enables the high performance event timer FED00000h FED01000h FED02000h FED03000h Selects the range of the HPET memory 72 9 BIOS Operation ACPI Cooling Options Menu Feature Active Trip Point Passive Trip Point Critical Trip Point Kontron User's Guide ETXexpress®-PC Option Description Disabled 40°C 45°C 50°C 55°C … 110°C Disabled 40°C 45°C 50°C 55°C … 110°C Disabled 40°C 45°C 50°C 55°C … 110°C Set the active trip point temperature, where the fan is activated Disables or enables the APIC SCI IRQ Disables or enables the high performance event timer 73 9 BIOS Operation Module Hardware Health Configuration Menu Feature H/W Health Function PWM 1 Mode Setting PWM 1 Ramp Rate Option Description Disabled Enabled Auto Fan Mode Fan Always On Full Fan Disabled Mode Fan Manually Mode Time Slot 1 Time Slot 2 … Time Slot 48 Enables and Disables the hardware health function in BIOS setup Controls the Fan interface If enabled limits the amount of change in the PWM duty cycle over a specified period of time Pulses / Rev [1..4] Selects the pulses of the fan / revision to show the correct RPMs Fan Voltage 5V 12V Selects fan voltage Kontron User's Guide ETXexpress®-PC 74 9 BIOS Operation Intel VT-d Configuration menu Feature Option Description Intel VT-d Disabled Enabled Enables and Disables the Intel VT-d feature Kontron User's Guide ETXexpress®-PC 75 9 BIOS Operation I2C Busses Menu Feature JIDA I2C Bus Speed Multi Master Sup. Clock Stretching Sup. Slow Device Support JILI I2C Bus Speed Multi Master Sup. Clock Stretching Sup. Slow Device Support Kontron User's Guide ETXexpress®-PC Option Description 166Khz 74Khz 45Khz … 2Khz Enabled Disabled Enabled Disabled Enabled Disabled 166Khz 74Khz 45Khz … 2Khz Enabled Disabled Enabled Disabled Enabled Disabled Selects the JIDA I2C Bus Speed Enables and disables Multi Master Support Enables and disables Clock Stretching Support Enables and disables Slow Device Support Selects the JILI I2C Bus Speed Enables and disables Multi Master Support Enables and disables Clock Stretching Support Enables and disables Slow Device Support 76 9 BIOS Operation PCIexpress Configuration Menu Feature Option Description Active State Power-Management Disabled Enabled Enables and disables the active state power management for PCIe devices Feature Option Description TCG/TPM Support No Yes Enable and disable the TCG and TPM Support Trusted Computing Menu Kontron User's Guide ETXexpress®-PC 77 9 BIOS Operation PCI/PnP Menu Feature Clear NVRAM Plug & Play O/S PCI Latency Timer Allocate IRQ to PCI VGA Palette Snooping PCI IDE BusMaster OffBoard PCI/ISA IDE Card IRQ3 … IRQ15 DMA Channel 0 … DMA Channel 7 Reserved Memory Size Kontron User's Guide ETXexpress®-PC Option Description No Yes No Yes 32 64 … 248 Yes No Disabled Enabled Disabled Enabled Clear NVRAM once during next system boot. No: all devices are initialized by BIOS Yes: OS has to initialize some devices Value in units of PCI clocks for PCI device latency register Decided if PCI VGA card does get an IRQ assigned if requested Disables and enables Palette Snooping Disables and enables PCI IDE Busmaster Auto PCISlot 1 PCISlot 2 … PCISlot 6 Available Reserved Available Reserved Disabled 16k 32k Some IDE Cards needs this , with set to Auto it works with most cards Available: IRQ useable by PCI/PnP devices Reserved: IRQ is reserved for ISA devices Available: DMA useable by PCI/PnP devices Reserved: IRQ is reserved for ISA devices Size of memory block to reserve for legacy ISA devices 78 9 BIOS Operation 64k 9.3.3 Boot Menu Feature Option 1st Boot Device Selects detected devices 2nd Boot Device Selects detected devices Kontron User's Guide ETXexpress®-PC Description 79 9 BIOS Operation Boot Settings Configuration Feature Quick Boot Quiet Boot AddOn ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Wait For 'F1' If Error Hit 'DEL' Message Display Interrupt 19 Capture Kontron User's Guide ETXexpress®-PC Option Description Enabled Disabled Disabled Enabled Force BIOS Keep Current On Off Auto Disabled Enabled Disabled Enabled Disables or enables the quick boot feature Disabled: Shows normal POST messages Enabled: Shows OEM Logo during boot up Set Display Mode for Option ROM Select Power-On state for Num-Lock Disables and enables or auto selects PS/2 Mouse Support Wait for F1 key to be pressed, if error Enabled Disabled Disabled Enabled Displays: "Hit 'DEL' to run setup" during POST, if enabled Allows option ROMs to trap INT19h if enabled 80 9 BIOS Operation 9.3.4 Security Menu Feature Option Change Supervisor Password Type in Change User Password Type in Boot Sector Virus Protection Disabled Enabled 9.3.5 Description Enables or disables boot sector virus protection. Exit Menu Kontron User's Guide ETXexpress®-PC 81 10 Appendix A: JIDA Standard 10 Appendix A: JIDA Standard Every board with an on-board BIOS extension supports the following function calls, which supply information about the board. Jumptec Intelligent Device Architecture (JIDA) functions are called via Interrupt 15h. Functions include: ® AH=Eah ® AL=function number ® DX=4648h (security word) ® CL=board number (starting with 1) The interrupt returns a CL≠0 if a board with the number specified in CL does not exist. CL will equal 0 if the board number exists. In this case, the content of DX determines if the operation was successful. DX=6B6Fh indicates success; other values indicate an error. 10.1 JIDA Information To obtain information about boards that follow the JIDA standard, use the following procedure. Note: ® Call Get BIOS ID with CL=1. The name of the first device installed will be returned. If you see the result Board exists (CL=0), increment CL, and call Get BIOS ID again. ® Repeat until you see Board not present (CL≠0). You now know the names of all boards within your system that follow the JIDA standard. ® You can find out more information about a specific board by calling the appropriate inquiry function with the board’s number in CL. Association between board and board number may change because of configuration changes. Do not rely on any association between board and board number. Always use the procedure described above to determine the association between board and board number. Refer to the JIDA manual in the jidai1xx.zip folder, which is available from the Kontron Embedded Modules GmbH Web site, for further information on implementing and using JIDA calls with C sample code. Kontron User's Guide ETXexpress®-PC 82 11 Appendix B: Architecture Information 11 Appendix B: Architecture Information The following sources of information can help you better understand PC architecture. 11.1 Buses 11.1.1 ISA, Standard PS/2 – Connectors ® AT Bus Design: Eight and Sixteen-Bit ISA, E-ISA and EISA Design, Edward Solari, Annabooks, 1990, ISBN 0-929392-08-6 ® AT IBM Technical Reference Vol 1&2, 1985 ® ISA & EISA Theory and Operation, Edward Solari, Annabooks, 1992, ISBN 0929392159 ® ISA Bus Specifications and Application Notes, Jan. 30, 1990, Intel ® ISA System Architecture, Third Edition, Tom Shanley and Don Anderson, AddisonWesley Publishing Company, 1995, ISBN 0-201-40996-8 ® Personal Computer Bus Standard P996, Draft D2.00, Jan. 18, 1990, IEEE Inc ® Technical Reference Guide, Extended Industry Standard Architecture Expansion Bus, Compaq 1989 11.1.2 PCI/104 11.2 ® Embedded PC 104 Consortium ® The consortium provides information about PC/104 and PC/104-Plus technology. You can search for information about the consortium on the Web. ® PCI SIG ® The PCI-SIG provides a forum for its ~900 member companies, who develop PCI products based on the specifications that are created by the PCI-SIG. You can search for information about the SIG on the Web. ® PCI & PCI-X Hardware and Software Architecture & Design, Fifth Edition, Edward Solari and George Willse, Annabooks, 2001, ISBN 0-929392-63-9. ® PCI System Architecture, Tom Shanley and Don Anderson, Addison-Wesley, 2000, ISBN 0-201-30974-2. General PC Architecture ® Embedded PCs, Markt&Technik GmbH, ISBN 3-8272-5314-4 (German) ® Hardware Bible, Winn L. Rosch, SAMS, 1997, 0-672-30954-8 ® Interfacing to the IBM Personal Computer, Second Edition, Lewis C. Eggebrecht, SAMS, 1990, ISBN 0-672-22722-3 ® The Indispensable PC Hardware Book, Hans-Peter Messmer, Addison-Wesley, 1994, ISBN 0-201-62424-9 Kontron User's Guide ETXexpress®-PC 83 11 Appendix B: Architecture Information ® 11.3 The PC Handbook: For Engineers, Programmers, and Other Serious PC Users, Sixth Edition, John P. Choisser and John O. Foster, Annabooks, 1997, ISBN 0-929392-36-1 Ports 11.3.1 RS-232 Serial ® EIA232E standard ® The EIA-232-E standard specifies the interface between (for example) a modem and a computer so that they can exchange data. The computer can then send data to the modem, which then sends the data over a telephone line. The data that the modem receives from the telephone line can then be sent to the computer. You can search for information about the standard on the Web. ® RS-232 Made Easy: Connecting Computers, Printers, Terminals, and Modems, Martin D. Seyer, Prentice Hall, 1991, ISBN 0-13-749854-3 ® National Semiconductor The Interface Data Book includes application notes. Type “232” as search criteria to obtain a list of application notes. You can search for information about the data book on National Semiconductor’s Web site. 11.3.2 Serial ATA ® Serial AT Attachment (ATA) Working Group. This X3T10 standard defines an integrated bus interface between disk drives and host processors. It provides a common point of attachment for systems manufacturers and the system. You can search for information about the working group on the Web. We recommend you also search the Web for information on 4.2 I/O cable, if you use hard disks in a DMA3 or PIO4 mode. 11.3.3 USB 11.4 ® USB Specification. ® USB Implementers Forum, Inc. is a non-profit corporation founded by the group of companies that developed the Universal Serial Bus specification. The USB-IF was formed to provide a support organization and forum for the advancement and adoption of Universal Serial Bus technology. You can search for information about the standard on the Web. Programming ® C Programmer’s Guide to Serial Communications, Second Edition, Joe Campbell, SAMS, 1987, ISBN 0-672-22584-0 ® Programmer’s Guide to the EGA, VGA, and Super VGA Cards, Third Edition, Richard Ferraro, Addison-Wesley, 1990, ISBN 0-201-57025-4 Kontron User's Guide ETXexpress®-PC 84 11 Appendix B: Architecture Information ® The Programmer’s PC Sourcebook, Second Edition, Thom Hogan, Microsoft Press, 1991, ISBN 1-55615-321-X ® Undocumented PC, A Programmer’s Guide to I/O, CPUs, and Fixed Memory Areas, Frank van Gilluwe, Second Edition, Addison-Wesley, 1997, ISBN 0-201-47950-8 Kontron User's Guide ETXexpress®-PC 85 12 Appendix C: Document Revision History 12 Appendix C: Document Revision History Revision Date Edited by 0.1_pre 0.2_pre 0.3_pre 20.08.08 25.11.08 26.11.08 UMA UMA UMA 0.4_pre 0.5_pre 1.0 1.12.08 21.04.09 08.05.09 UMA UMA UMA Kontron User's Guide ETXexpress®-PC Changes Created preliminary manual. Added supply current tables Exchanged product picture, added onboard fan connector description, and description for HDMI and Displayport Added chapter 5.3 usage of different graphic interfaces Added BIOS Setup description Added Resource List 86
