Download ViewSonic N2060W User's Manual

ViewSonic
®
N2060w
LCD TV
- 使用手册
- 使用手冊
- User Guide
Model No. : VS11287-1G
CONTENTS
Important Safety Instructions -------------------------------------------------- 1
Copyright Information ------------------------------------------------------------ 2
Antenna Installation Instructions---------------------------------------------- 3
Cleaning the LCD TV ------------------------------------------------------------ 3
CONNECT PERIPHERAL EQUIPMENT
Front Panel Control Knobs ---------------------------------------------------- 4
Preparation ----------------------------------------------------------------------- 5
OPERATING INSTRUCTIONS
Use of the remote control------------------------------------------------------- 6
remote control--------------------------------------------------------------------- 7
Preparation ----------------------------------------------------------------------- 8
To use the menus ---------------------------------------------------------------- 10
Main menu ------------------------------------------------------------------------- 10
Headphone ------------------------------------------------------------------------ 16
Tips ---------------------------------------------------------------------------------- 16
Appendix
Specification------------------------------------------------------------------------ 17
Troubleshooting
Customer Support --------------------------------------------------------------- 20
Limited Warranty----------------------------------------------------------------- 21
Important Safety Instructions
1.
Read these instructions completely before using the equipment.
2.
Keep these instructions in a safe place.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this equipment near water. Warning: To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
6.
Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the LCD TV”
in this guide for further instructions.
7.
Do not block any ventilation openings. Install the equipment in accordance with the
manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
9.
Do not attempt to circumvent the safety provisions of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third prong are
provided for your safety. If the plug does not fit into your outlet, consult an electrician for
replacement of the outlet.
10. Protect the power cord from being tread upon or pinched, particularly at the plug, and the
point where if emerges from the equipment. Be sure that the power outlet is located near
the equipment so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this equipment when it will be unused for long periods of time.
14. Refer all servicing to qualified service personnel. Service is required when the unit has
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid
is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if
the unit does not operate normally or has been dropped.
ViewSonic
1
N2060w
Copyright Information
Copyright © ViewSonic Corporation, 2006. All rights reserved.
®
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right
to change product specifications without notice. Information in this document may change
without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com.
Product Name:
For Your Records
Model Number:
Document Number:
Serial Number:
Purchase Date:
N2060w
ViewSonic LCD TV
VS11287-1G
N2060w-1G_UG_ENG Rev. 1A 03-02-06
_________________________________
_________________________________
Product disposal at end of product life
ViewSonic is concerned about the preservation of our environment. Please dispose of this
product properly at the end of its useful life. Your local waste disposal company may provide
information about proper disposal.
The lamp in this product contains mercury. Please dispose of properly in accordance with
environmental laws of your location.
ViewSonic
2
N2060w
Antenna Installation Instructions
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and built-up static charges, Article 810
of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges. Do not disconnect the antenna or the
power cord during a heavy storm lighting may strike while you are holding the cable cord, causing serious
injury; turn off your LCD TV and wait for the weather to improve.
3. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits, When installing an outside antenna
system, extreme care should be taken to keep from touching such power lines or circuits as contact with them
might be fatal.
Antenna
Ground clamp
Antenna discharge unit
Electric service equipment
Ground clamps
Grounding conductors
Power service grounding electrode system
Cleaning the LCD TV
• Make sure the LCD TV is turned off.
• Never spray or pour any liquid directly onto the screen or case.
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft,
lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-abrasive detergent
onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the LCD TV screen or
case. Some chemical cleaners have been reported to damage the screen and/or case of the LCD TV. ViewSonic
will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.
ViewSonic
3
N2060w
CONNECT PERIPHERAL EQUIPMENT
FRONT PANEL CONTROL KNOBS
Source(信号源)①: Press to select your input source.
Volume（音 量）②③: Press to confirm your function selection (when the
OSD main menu displayed) or adjust volume (without OSD
main menu)
Channel（频道）④⑤: Select the intended function by pressing the two keys
(when the OSD main menu displayed), or switch the channels
in the TV mode (without OSD main menu)
Menu( 菜单)⑥: Press to show the OSD menu and exit OSD menu at the TV mode.
Power（电源）⑦: Press to turn on or off the TV.
Power Lock
Press Source for 10 seconds can lock the function of Power button
OSD Lock
Press Menu for 10 seconds can lock the function of Menu button
ViewSonic
4
N2060w
There is a wide range of video and audio equipment that can be connected to
your TV. The following connection diagrams show you how to connect them.
PREPARATION
Lay the LCD TV with the screen down on a table, as it will be easier
to connect your peripheral equipment. Please take precaution on page8 not to
damage the screen.
1. VGA audio input
2. VGA input
3. AC power input terminal
4. Headphone outlet
5. AV signal input
6. Left audio track input (AV/S-Video)
7. Right audio track input (AV/S-Video)
8. S-Video signal input
9~11. YPbPr Component signal input
12. YPbPr left audio track input
13. YPbPr right audio track input
14. TV signal input
ViewSonic
5
N2060w
OPERATING INSTRUCTIONS
USE OF THE REMOTE CONTROL
POWER (电源)
Press to turn on/off the
TV. The TV is never
completely powered off
unless it is physically
unplugged.
Mute(静音)
Temporarily interrupt the
sound or restore it.
Status(状态)
(1) Display the channel
number when input TV
RF
(2) Display input source
when input the other
sources.
Channel (频道)
Press or to browse
through the TV
channels。
Volume (音量)
Press + or – to adjust
the volume.
Return(回复)
To display the previously
selected TV channel.
0~9/100 Digit buttons
To select a TV channel.
Menu(菜单)
Press repeatedly to
display OSD menu.
Sound switch
(声音切换)
Could choose single
track, sterieo, language I
or language II in TV mode
Source(信号源)
Select your input source:
press repeatedly to select
TV, Video AV, S-VIDEO,
YPbPr or PC
Sleep(睡眠)
With this key you can set
a time period after which
the TV should switch itself
to standby. Press the key
repeatedly to select the
number of minutes. The
counter runs 5~120
minutes. Timing controller
start to count down after
the menu disappeared
PC(电脑)
Press this button to
turn PC mode
Notes on the Remote Control
• Direct light may affect the remote controls effective range.
• Avoid subjecting the remote control to shocks or vibrations.
• Avoid placing the remote control in humid and hot environments
such as direct sunlight.
• Remove the batteries when not using the remote control for long
periods.
ViewSonic
6
N2060w
3. Remote control:
Remove the cover of the battery compartment. Insert the 2 batteries
supplied (Type AAA 1.5V).
CAUTION
Only use the specified AAA batteries.
Do not mix new and old batteries. This may result
in cracking or leakage, which may pose a fire risk or
lead to personal injury.
Insert batteries according to the (+) and (-) markings.
Inserting the batteries incorrectly may result in
cracking or leakage, which may pose a fire risk or
lead to per-sonal injury.
Dispose of batteries in accordance with local laws
and regulations.
Keep batteries away from children and pets.
If the remote control will not be used for an extended
period of time, remove the batteries.
ViewSonic
7
N2060w
PREPARATION
1. Assembly
Take out TV and base from carton, assembled by three pieces
screws, which you could find from the accessory box. Shown in the
figures below:
Place the base on a
solid surface
Note: Lock the screw
middle first, then the
others, to avoid holes
aiming incorrectly
ViewSonic
8
N2060w
2. Place the TV on a solid surface.
Ensure that the TV is placed in a position to allow free flow of air. Do not
cover the ventilation openings on the back cover.
To prevent any unsafe situations, no naked flame sources, such as lighted
candles, should be placed on or in the vicinity.
Avoid heat, direct sunlight and exposure to rain or water. The equipment
shall not be exposed to dripping or splashing.
3. Insert the aerial plug firmly into the aerial socket at the back of the TV.
4. Power:
Insert the power cord in the wall socket having an AC power supply.
5. Turn the TV on:
You could turn on or off TV by the power key on the peak of TV, or by the
power key on remote control.
The indicator light in the front of TV is dark when the TV is ‘OFF’.
The indicator light in the front of TV is blue when the TV is ‘ON’.
ViewSonic
9
N2060w
TO USE THE MENUS
1.
2.
3.
4.
Press the MENU button to display or close main menu.
Use the cursor up/down to select a menu item.
Use the cursor left/right to enter a submenu or enable/disable the function.
Press the MENU button to exit the menu.
MAIN MENU
Press the MENU button to enter the main OSD (On Screen Display).
Adjust items including Sound Setup, Picture Setup, Function Setup and TV
setup.
When the input source is PC, YPbPr, AV or S-VIDEO mode, only the Sound
Setup, Picture Setup and Function Setup can be selected; shown in the figure
below:
When the input source is TV mode, the Sound Setup, Picture Setup, Function
Setup and TV setup can be selected, shown in the figure below:
ViewSonic
10
N2060w
Sound Setup (Same for all modes)
1. The range of adjusting volume, bass and treble is from 0~100.
2. Select “ON” or “OFF” in Audio selection to control the sound output.
3. The range of adjusting Balance is -50~+50; when adjusting from 0 to -50,
the sound from the right track fades until silence; when adjusting from 0 to
+50, the sound from the left track fades until silence.
4. AVL: you can set it “ON” or “OFF”.
The function is to adjust the input sound automatically. You may enable
this function when you notice that the sound in the two tracks are very
different, in order to prevent the bad sound effect result from large sound
variation.
5. Select "ON" or "OFF" for Loudness: a default setting is preset, you may
adjust when necessary.
The following menu will appear when selecting continuously:
6. Audio mode: Designed for the different types of sound output, wherein, the
dialogue, music and theater modes are preset; you can set Bass, Treble
and Equalizer in sound output mode according to your preference.
7. Equalizer: You can select and adjust the 100, 300, 1K, 3K and 8K
respectively (the figures represent the sound frequency range).
8. Reset To Default: Reset the sound setting to the factory default value.
ViewSonic
11
N2060w
Picture Setup
When the input source is in PC mode, shown in the figure below:
1. Brightness and Contrast: The range can be adjusted from 0~100.
2. Position: There are two options, Horizontal and Vertical, which can be
adjusted from -50 to +50.
3. Video noise: There are two options, Phase and Clock, which can be
adjusted from -50 to +50.
4. Sharpness: Select from six options Softest, Soft, Normal, Sharp, Sharpest
and Auto. You may adjust the above options according to your preference.
5. Auto Adjust: Auto-sizing function for VGA input..
6. Info: Prompt the current PC input resolution
7. Color Temp.: There are four options of color temperature provided for
users - Cold, Normal, Warm and Personal. You can select the three color
temperatures of Cold, normal and warm, or manually adjust manually red,
green or blue in the personal setting (you can only adjust red, green and
blue in the personal setting).
8. Reset to default: It is used to reset the picture settings to the factory
default mode.
ViewSonic
12
N2060w
When the input source is TV, YPbPr, AV or S-VIDEO mode, shown in the
figure below:
1.
2.
3.
4.
5.
6.
7.
8.
Brightness and Contrast: The range can be adjusted from 0~100; use
Brightness and Contrast options to adjust the brightness of picture.
Color: The range can be adjusted from 0~100; use this option to adjust
the color saturation of picture.
Sharpness: Select from six options: Softest, Soft, Auto, Sharp, sharpest
and Auto. You can adjust the sharpness of picture using any option above.
Hue: The range can be adjusted from -50~+50; use this option to adjust
the color of picture.
Dyn. Skin tone: When the Dynamic skin tone is ON, the skin tone of
person in the picture becomes more vivid.
Color Temp.: There are three options of color temperature provided for
users - warm, normal and cold.
Zoom: There are three options --4: 3, fullscreen and widescreen provided
for zoom in/zoom out.
Reset to default: It is used to reset the picture settings to the factory
default mode.
ViewSonic
13
N2060w
Function Setup, shown in the figure below:
1. OSD time out: could set OSD display time from 10 seconds to 60
2. Language: could set OSD language to English, simplfied Chinese or
traditional Chinese
3. Sleep timer: set the time after which the product will enter standby status
automatically
4. Reset to default: It is used to reset the OSD settings.
1. Sleep timer：Start to count down after the sleep timer set, could choose
from 5 min. to 120 min. Count down shown on the screen
when only one minute left before enter standby
2. Reminder timer: Could not be set by personal, to show the time after which
the product will enter standby
ViewSonic
14
N2060w
TV setup
The following menu appears only in the TV mode.
o
1. Program no. : Shows the current channel number
2. Color system: shows the current picture input system（shows auto after
auto search）
3. Sound system: shows the current sound input system（shows auto after
auto search）
4. Auto search: Used to auto search and storage program
5. Frequency: Shows the frequency of current channel. Could adjust
frequency slightly by the right and left button to get the result what you want
6 . AFC can be set to ON or OFF. When it is set to ON, the TV will search the
TV signal automatically; when there is any offset in the signal, it will
automatically adjust the channel to the correct position.
7. Skip can be set to ON or OFF. When it is set to ON, pressing the up key on
the remote control or on the front panel can skip a channel.
8. Reset to default: Reset to the factory default value.
ViewSonic
15
N2060w
HEADPHONE
1. The headphone jack is located at the right side of the TV.
2. The MUTE key on the remote control works on both internal speaker and
the headphone.
3. Use volume key to adjust the volume.
TIPS
Care of the screen
Do not rub or strike the screen with anything hard as this may scratch, mar, or
damage the screen permanently.
Unplug the power socket before cleaning the screen. Dust the TV by wiping
the screen and the cabinet with a soft, clean cloth. If the screen requires
additional cleaning, use a clean, damp cloth. Do not use liquid cleaners or
aerosol cleaners.
Mobile telephone warning
To avoid disturbances in picture and sound, malfunctioning of your TV or even
damage to the TV, keep away your mobile telephone from the TV.
End of life directives
We are paying a lot of attention to produce environmentally friendly in green
focal areas. Your new receiver contains materials, which can be recycled and
reused.
At the end of its life specialized companies can dismantle the discarded
receiver to concentrate the reusable materials and to minimize the amount of
materials to be disposed of.
Please ensure you dispose of your old receiver according to local regulations.
ViewSonic
16
N2060w
Appendix
Specifications
Panel
Type
20” TFT-LCD
Active Matrix wide-XGA, 1360x 768
Color
Viewing angles
Input signal
Anti-glare coating
160° H/ 160° V
Video
Fh: 32-48KHz, Fv: 50-60Hz
VGA input*1
TV system antenna
Composite Video input*1
S-Video*1
Component video*1 (YPbPr / YCbCr)
Audio
Audio input*1
RCA*1 for AV and S-Video
RCA*1 for YPbPr / YCbCr
Compatibility
PC
Up to 1360x768 Non-interlaced
Resolution
Supported
640x480 @60Hz
800x600 @56Hz
800x600 @60Hz
1024x768@60Hz
1280x768@60Hz
1280x720@60Hz
1280x1024@60Hz
1360x768@60Hz
Speaker output
3W+3W
Power
Voltage
100-240VAC, 50/60Hz
Operating
Temperature
5℃ to 35℃
conditions
Humidity
10% to 85%(no condensation)
ViewSonic
17
N2060w
Storage
Temperature
-25℃ to 60℃
conditions
Humidity
10% to 85%(no condensation)
Dimension
Physical
521.84mm(W) x 419.52mm(H) x 180.83mm(D)
20.55”(W) x 16.52”(H) x 7.12”(D)
Package
595mm(W) x 512mm(H) x 226mm(D)
23.4”(W) x 20.2”(H) x 8.9”(D)
Weight
Net
6.9Kg (15.2 Ib.)
Gross
9 Kg (19.9 Ib.)
Regulation
CB, CCC
Power saving
On
<90 W (Blue LED)
modes
Active off
<3 W
Preset timing modes (Pre-adjusted to VESA 1360x768 at 60Hz)
Warning: Do not set the graphics card in your computer to exceed these
refresh rates. Doing so many result in permanent damage to the LCD.
Note: Product specifications are subject to change without notice.
ViewSonic
18
N2060w
Troubleshooting
No power
• Make sure the LCD TV is properly connected.
• Make sure the AC power cord is properly connected.
• Make sure the AC power is ON, DC power button is ON (Green LED).
• Plug another electrical device (like a radio) to the power outlet to verify that the outlet is
supplying the proper voltage.
Poor or no picture
• The TV station may be experiencing problems. Try another channel.
• The Cable TV signal may be scrambled or encoded. Please contact your local cable
operator.
• Make sure that connection to other components are correct.
• Make sure that setup has been done correctly after connections.
• Make sure the correct input is selected and the input signal is compatible.
Strange color, light color, or color misalignment
• Ensure that the video cable is securely connected.
• The picture may appear dim in a brightly lit room.
• Adjust brightness and contrast.
• Check the input signal setting.
No sound
• Check your audio connections
• The MUTE button may have been pressed, try pressing this button again.
• Check your audio settings, your TV audio may be set to minimum.
• Press the Volume + (Up) button on the remote control.
Remote control unit does not operate
• Make sure batteries are inserted correctly.
• Batteries could be weak or dead. Replace batteries.
• Is a fluorescent light illuminated near the remote control sensor?
• The path of the remote control beam may be blocked. Make sure the path is clear and that
the remote control is aimed at the remote control sensor on the TV.
• Press only one button at a time and it is the correct one for the operation you want to
perform.
Unit cannot be operated
• External influences such as lightning or static electricity may cause improper operation.
In this case, operate the unit after first turning on the power of the LCD TV and the AVC
System, or unplug the AC cord for 1 to 2 minutes, then replug again.
Power is cut off suddenly
• Is the sleep timer set?
• The internal temperature of the unit has increased. Remove any objects blocking the vent
or clean as necessary.
No CATV reception (or no reception above CH13)
• Is the AIR/CABLE option set correctly? Please set the AIR/CABLE option to CABLE.
• CATV is connected improperly or not connected; please check all the CATV connections.
• The cable TV service is interrupted; please contact your cable operator.
Picture is cut off/with sidebar screen
• Is the image positioned correctly?
• Are screen mode adjustments such as picture size set correctly?
ViewSonic
19
N2060w
Cusomer Support
For technical support or product service, see the table below or contact your reseller.
Note: You will need the product serial number.
Country/
Region
Web Site
Telephone
Email
China
www.viewsonic.com.cn
800 820 3870
[email protected]
ViewSonic
20
N2060w
Limited Warranty
VIEWSONIC® LCD TV
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty
period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will at its
sole option repair or replace the product with a like product. Replacement product or parts may include remanufactured or
refurbished parts or components.
How long the warranty is effective:
ViewSonic LCD TVs are warranted for one (1) year for all parts excluding the light source and one (1) year for labor from
the date of the first customer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by ViewSonic.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meeting ViewSonic’s specifications.
g. Normal wear and tear.
h. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed
on the product for an extended period of time.
4. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support at 800-888-8583. You will
need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your
address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the implied
warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of
the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states
do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so
the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or
your local ViewSonic dealer.
Warranty_LCDTV
4.3: ViewSonic LCD TV Warranty Rev. 1a
ViewSonic
1 of 1
Release Date: 03-31-05
21
N2060w