Download Star Micronics TSP400 User's Manual

THERMAL PRINTER
TSP400 Series
TECHNICAL MANUAL
[THIRD EDITION]
NOTICE
• All rights reserved. Reproduction of any part of this manual in any form whatsoever,
without STAR’s express permission is forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at the time
of going to press. However, should any errors be detected, STAR would greatly
appreciate being informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in this
manual.
© Copyright 1994 Star Micronics Co., LTD.
INTRODUCTION
This manual is intended as a reference for maintenance personnel carrying out periodic maintenance or repair
in the field. It is not intended for general users.
• This manual is comprised of the following chapters.
Chapter 1 Specifications and Operation
Chapter 2 Theory of Operation
Chapter 3 Parts Replacement and Related Adjustments
Chapter 4 Maintenance and Lubrication
Chapter 5 Parts Lists
• First edition
: Dec. 1994
Second edition : Jul. 1995
Third edition : March 1997
■ Model Name
TSP 4
1
2
D
—
120
Voltage
120 : 120VAC
220 : 220VAC
240 : 240VAC
Interface
D: RS232C
K: RS422A
C: Parallel
None: Without interface
Mechanism type
2: 40 columns
Printer type
1: Standard
4: With autocutter
TSP400-series thermal printer
1
2
3
4
5
CHAPTER 1
SPECIFICATIONS AND OPERATION
1.
General Specifications ......................................................................................... 3
2.
External Appearance and Internal Configuration .............................................. 4
3.
DIP-Switch Settings .............................................................................................. 5
4.
Print-Density Adjustment ..................................................................................... 8
5.
Sensor Adjustment ............................................................................................... 9
6.
Setting Memory Switches from the Control Panel ........................................... 11
7.
Test Print .............................................................................................................. 12
8.
HEX Dump ............................................................................................................ 12
9.
Page/Line Mode Switch ...................................................................................... 13
10. Exposing the Peripheral Unit Connector .......................................................... 14
11. Changing the Interface Board ............................................................................ 15
1
SPECIFICATIONS AND OPERATION
–2–
SPECIFICATIONS AND OPERATION
General Specifications
Printing method
Resolution
Printable width
Printing speeds
Printable characters
Line thermal direct
8 dots/mm (H) × 8 dots/mm (V)
75 mm in Line Mode; 80 mm in Page Mode
50 mm/sec and 25 mm/sec
1 Page mode: ANK, International
2 Line mode: ANK, International, Special, Block graphic, IBM
special, IBM block graphic, Kanji
NOTE: ANK is comprised of ASCII characters and katakana
1 Page mode
Small
8×16
Standard
16×24
Wide
24×32
OCR-B
16×24
2 Line mode
Kanji
24×24 (12×24)
IBM block graphic 12×24 or 12×32
All others
12×24
Character matrixes
Paper
Recommended brands
TF50KS-E, TF62KS-E (Nippon Paper Industries)
KP50-HEAEX (New Oji Paper Co., Ltd.)
82 mm (3.25 inches)
60 to 150 µm
External 115 mm max.
25.4 mm (1 inch)
RS232C, RS422A, or Parallel
Width
178 mm (TSP412D)
178 mm (TSP442D)
Depth
226 mm (TSP412D)
244 mm (TSP442D)
Height
256 mm (TSP412D)
256 mm (TSP442D)
Weight
3.4 kg (TSP412D)
3.7 kg (TSP442D)
120VAC, 220VAC, 240VAC
Operating
5˚C to 40˚C; 25%RH to 85%RH
Nonoperating
-20˚C to 60˚C; 10%RH to 90%RH
Lifetime
300,000 cuts (if paper debris is cleared)
Minimum cut length
25.4 mm (1 inch)
Width
Thickness
Roll diameters
Internal
Interface
Dimensions and weight
Power supply
Ambient conditions
256mm
Autocutter
256mm
1.
mm
178
mm
178
226
mm
244
mm
3.4kg
3.7kg
(TSP412)
(TSP442)
Fig. 1-1 External Dimensions
–3–
SPECIFICATIONS AND OPERATION
2.
External Appearance and Internal Configuration
Control Panel
Printer cover
Power switch
Power cord
CONNECTOR COVER
(Peripheral unit connector)
Interface cover
Interface connector
Fig. 1-2 Internal Configuration (TSP412D)
–4–
SPECIFICATIONS AND OPERATION
3.
DIP-Switch Settings
DIP switches are located on the interface PCB. The number of switches depends on the interface type.
(1)
Setting the DIP Switches
Fig. 1-3 DIP-Switch Settings
1 Remove the screw holding the ROM cover in place. (The screw is located at the base of the paper-roll holder.)
2 Remove the ROM cover, exposing the main and interface PCBs.
–5–
SPECIFICATIONS AND OPERATION
Interface PCB (RS232C)
DIP switches
VR3 (Paper-out sensor)
VR2 (Transmissive sensor - fine)
VR1 (Transmissive sensor coarse)
VP4 (Black-mark sensor)
EPROM
Main PCB
Opening under ROM cover
Fig. 1-4 Main and interface PCBs
3 Set the DIP switches on the interface PCB.
2.
DIP-switch values
1 RS232C interface
This board has a single 8-bit DIP switch. Switch settings are as follows.
Switch
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
Setting
ON
OFF
DTR
8 bits
No parity
Odd
Ineffective
XON/XOFF
7 bits
Parity used
Even
Effective
Baud
Handshaking
Data length
Parity use
Parity type
DC1/DC3
Status of printer power
* All of these are set to ON before the printer is shipped from the factory.
–6–
SPECIFICATIONS AND OPERATION
Baud
1-1
1-2
2400BPS
4800BPS
9600BPS
19200BPS
OFF
OFF
ON
ON
OFF
ON
ON
OFF
Mode
DC1/DC3 invalid
DC1/DC3 effective
Addressable
Status of printer power
1-8 ON
1-8 OFF
Printer selected
Printer de-selected
Printer selected
Printer de-selected
Printer de-selected
Printer selected
To select a mode:
With an RS-232C interface, use DIP switches 1-7 to select the mode. With an RS-422A interface, use DIP switch
#2.
2 RS422A interface
This board has two DIP-switches: one 8-bit switch and one 4-bit switch.
DIP switch #1 (8 bits):
Identical to the DIP switch on the RS232C (see above). But note that bit 1-7 is meaningless.
DIP switch #2 (4 bits):
DC1,3 off
Address
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
#12
#13
#14
DC1,3 mode on
SW2-1
SW2-2
SW3-3
SW2-4
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
* DIP-SW #2 overrides the DIP-SW #1 DC1/3 setting (bit 1-7).
* DIP-SW #2 factory setting: All ON
3 Parallel (Centronics) interface
The parallel-interface board has no DIP switches.
–7–
SPECIFICATIONS AND OPERATION
4.
Print-Density Adjustment
Adjust the print density in accordance with the sensitivity of the paper being used. The adjustment procedure is as follows.
Density Adjustment Aperture
Fig. 1-5 Print-Density Adjustment
1 Remove the interface cover, located the rear side of the printer. The cover fits into place; no screws are used.
2 The density adjustor (variable resistor) is now accessible through the aperture located to the left of the interface
connector.
3 Insert a screwdriver (regular or phillips-head) into the aperture and rotate as necessary. The adjustor has a
rotational range of approximately 180 degrees.
4
About 90˚
About 90˚
Dark
Light
5 Avoid setting density too high for sensitive paper types. Excessive dark values may cause the paper to swell,
degrading the image quality.
6 Some thermal papers may fail to produce a strong image when running at 50mm/sec printing speed, even at
maximum density setting. If you have this problem, reduce the print speed to 25mm/sec.
–8–
SPECIFICATIONS AND OPERATION
5.
Sensor Adjustment
There are three different sensors: the transmissive sensor (label start-position detector), the black-mark sensor, and the
paper-out sensor. Adjustment procedures are described below. First note the following general points.
• The transmissive sensor level requires precise setting. Because transmission rates vary widely among different
types of label paper, we recommend that the sensor be readjusted each time the user changes to a different paper
type.
• Because black marks are likely to be similar across different paper types, the black-mark reflective sensor may
not require readjustment each time the paper type is changed. But you will still have to adjust it if the new paper
has a different consistency or uses a different black-mark density, or if the paper-feed routing is changed.
• In most generally not necessary to adjust the paper-out sensor.
–9–
SPECIFICATIONS AND OPERATION
Sensor adjustment procedures are as follows.
1)
Remove the ROM cover, located beneath the paper-roll holding area.
2)
Hold down the FEED and ON LINE buttons while switching on the power, and continue to hold them down until
you hear a triple beep. (This will take about five seconds.) When you hear the triple beep, release the buttons to
enter sensor-adjustment mode.
a)
Reflective Sensor
• Insert a non-black area of paper into the mechanism’s sensor area.
• Rotate the main PCB’s reflective-sensor adjustment knob (VR4) to the point where the Head Up LED comes
on.
b)
Paper-Out Sensor
• Insert a non-black area of paper into the mechanism’s sensor area.
• Rotate the main PCB’s paper-out-sensor adjustment knob (VR3) to the point where the Paper End LED switches
on.
c)
Transmissive Sensor
• Insert the backing portion of a label sheet into the mechanism’s transmissive sensor area. (Insert the backing
part only, not the label itself.)
• Adjust the main PCB’s coarse (VR1) and fine (VR2) transmissive-sensor adjustment knobs to the point where
the Error LED comes on.
Note: When setting paper, be sure to lower the head so that it is close to its normal fixed position.
After the sensor has been adjusted, press the ON LINE switch to exit the sensor adjustment mode and return to the
normal operation mode.
– 10 –
SPECIFICATIONS AND OPERATION
6.
Setting Memory Switches from the Control Panel
The TSP400 uses EEPROM memory switches in place of corresponding hardware switches. All EEPROM switch settings
can be changed by software. A number of these switches are also changeable from the control panel.
(1)
Paper-Feed Mode (Continuous or Next-Top)
When the feed mode is set to next-top, the printer can come online only if loaded with labels or marked paper. If the printer
fails to come online you will not be able to change the feed-mode setting by command; you will therefore have to change
it using the control panel.
1 Hold down the FEED and ON LINE buttons while switching on the power, and continue to hold them down until
you hear a double beep. (You will first hear a single beep, followed by a pause, followed by the double beep.)
Release the buttons immediately after hearing the double beep.
2 Press the ON LINE button to select continuous feed (the printer beeps once), or press the FEED button to select
next-top feed (the printer beeps twice). If you select next-top feed, the printer automatically starts paper feed
and looks for the next top.
(2)
Sensor Mode
The printer may be set to use either the transmissive or the reflective sensor for next-top detection. You can make this
setting as follows.
1 Hold down the ON LINE button while switching on the power, then continue to hold it down until you hear a
double beep. (You will first hear a single beep, then a pause, then the double beep.) Release the ON LINE button
immediately after hearing the double beep.
2 Press the ON LINE button to select the reflective sensor (the buzzer beeps once), or press the FEED button to
select the transmissive sensor (the buzzer beeps twice).
– 11 –
SPECIFICATIONS AND OPERATION
7.
Test Print
To generate a test print (self-test), hold down the FEED button while switching on the power.
Note: The test print continues as long as the FEED button is held down.
8.
HEX Dump
Set the printer into hex-dump mode as follows: hold down the ONLINE button and switch the power on, then release the
ONLINE button as soon as you hear a single beep. The printer is now set to print a hex dump of the data sent from the
host.
Note: The HEX Dump mode continues to be effective until the power supply is turned off.
– 12 –
SPECIFICATIONS AND OPERATION
9.
Page/Line Mode Switch
The TSP400 series supports two entirely different command sets: “Page Mode” and “Line Mode.” You can select the
mode either by software or from the control panel. To select from the control panel, proceed as follows.
NOTE: This function will not become meaningful until Line Mode
software has been introduced.
1 Hold down the ON LINE button while switching on the power, then continue to hold it down until you hear a
triple beep. (This will take about five seconds.)
2 Press the ON LINE button to select Page Mode (the buzzer beeps once), or press the FEED button to select Line
Mode (the buzzer beeps twice).
– 13 –
SPECIFICATIONS AND OPERATION
10. Exposing the Peripheral Unit Connector
When operating in Line Mode, the printer can use the peripheral unit connector to drive a cash drawer or other such external
device. But note that the connector is originally hidden by a portion of the interface cover.
Connector cover
Fig. 1-6 Peripheral Unit Connector
To prepare the connector for use, remove the “connector cover” portion of the interface cover (see illustration) by gently
bending and breaking it with a pliers. Be sure to remove any remaining burrs using a cutter or other such tool.
– 14 –
SPECIFICATIONS AND OPERATION
11. Changing the Interface Board
You can change the printer’s interface by replacing the interface board. The replacement procedure is as follows.
Interface board PCB guide
Printer
Connector
Interface
board
Screws (3)
Interface cover
Fig. 1-7 Changing the Interface Board
1 Remove the interface cover, located on the rear side of the printer.
2 Remove the three screws holding the interface board in place.
3 Remove out the board by pulling on the pull sheet fastened to the connector.
4 Fit the replacement interface board to the guides and push all the way in so that the connector is fully engaged.
5 Fasten the outer plate to the printer with three screws.
6 Replace the interface cover.
Note: The printer automatically detects changes in interface type.
– 15 –
SPECIFICATIONS AND OPERATION
– 16 –
CHAPTER 2
THEORY OF OPERATION
This chapter describes the operating principles of the circuitry and printer mechanism.
1.
Block Diagram ..................................................................................................... 19
2.
Main and Interface PCBs .................................................................................... 21
2-1.
Interface ................................................................................................................. 21
2-1-1. RS232C .............................................................................................................. 21
2-1-2. RS422A .............................................................................................................. 22
2-1-3. Parallel interface ............................................................................................... 23
2-2.
Editing and Printing .............................................................................................. 24
2-2-1. Editing ............................................................................................................... 24
2-2-2. Thermal head .................................................................................................... 24
2-2-3. Head current control ........................................................................................ 25
3.
2-3.
Feed-Motor Drive Circuit ...................................................................................... 26
2-4.
Power-On Reset Circuit ........................................................................................ 27
2-5.
+5V Line Voltage Detector Circuit ....................................................................... 28
Printer Mechanism .............................................................................................. 29
3-1.
Thermal Head ........................................................................................................ 29
3-2.
Paper-Feed Mechanism ........................................................................................ 29
3-3.
Detectors ............................................................................................................... 30
2
THEORY OF OPERATION
– 18 –
THEORY OF OPERATION
1. Block Diagram
The following diagram illustrates the relationship between the control board (main PCB) and its peripherals.
Data flow (Host computer)
Interface board
RS232C, RS422A, or parallel
Main PCB
EEPROM
Printer mechanism
EPROM
128K × 16bits
Head driver
Thermal
head
PS-RAM
128K × 16bits
Motor driver
Feed motor
S-RAM (backup)
8K × 8 bits
Cutter driver
Autocutter
Sensor circuitry
Sensor
External device
driver
External
device
Gate array
(8)
(16)
(16)
Control
panel
(8)
(16)
Kanji ROM
256K × 16 bits
CPU
DC-DC converter
24V
Power unit
Fig. 2-1 Block Diagram
– 19 –
THEORY OF OPERATION
1. 1 Control board
The interface board relays data from the host computer to the main board. The main board’s CPU stores the data
into local RAM.
It then reads out the data, edits it according to the control program stored in the board’s ROM, and prints the results
by issuing appropriate drive signals to the printer mechanism.
[Block Description]
a. CPU: HD641300F10T
CMOS single-chip computer
Controls overall printer operation.
b. EPROM: 128 K × 16 bits
Contains the CPU control program.
c. PS-RAM: 128 K × 16 bits
Work area and data buffer
d. S-RAM
Saves format data and externally defined characters.
Backed up by super capacitor.
e. EEPROM: 1024 bits
Stores printer settings. Settings can be changed by software. (Used in place of dip-switches.)
f. Interface board
Interfaces the main board with the host computer.
There are three versions, each for a different interface type: RS232C, RS422A, or Centronics parallel.
g. Gate array
Executes various types of signal processing.
h. Drivers
The various drivers convert signals received from the CPU and gate array into the drive signals that directly
control the printer mechanism.
i. DC-DC converter
Converts the supplied 24V to 5V.
1. 2 Control Panel
Provides manual control switches and operational indicators.
1. 3 Printer mechanism
Comprised of thermal head, paper-feed motor, and sensor mechanism.
1. 4 Power unit
Converts primary power to DC24V.
1. 5 External device
External device (such as cash drawer) driven by signals issued by the control board.
– 20 –
THEORY OF OPERATION
2.
Main and Interface PCBs
The main PCB and interface PCB provide the drive circuitry for the TSP-400 printer series. The two boards are connected
via 40-pin connectors.
2-1. Interface
2-1-1. RS232C interface
CN3
CN1 CN9
IC10
Gate array
IC1
IC5
CPU
D2O
D2I
B12
B12
DTR
ACK
R-CH
D1O
D1I
B14
B14
R1I
R1O
A15
A15
R2I
R2O
B15
B15
TXD0
TXD
RXD0
RXD
RXD1
CTS
HD151232FP
RS232C Interface PCB
Main PCB
Fig. 2-2 RS232C Interface
Data flow from host to printer: IC1 receives serial data from the host computer via RXD, converts the signal voltage
from RS232C level to TTL level, and passes the result to the CPU. The CPU converts the serial data to parallel and stores
it into buffer memory.
Data flow from printer to host: The CPU generates data, converts it into serial form, then passes it to IC1. IC1 converts
the signal voltage from TTL level to RS232C level, then outputs the result over the TXD line.
The CTS line is hardware-connected, but the connection is not recognized by software. (The printer does not monitor the
signal.)
– 21 –
THEORY OF OPERATION
2-1-2. RS422A interface
CN3
IC1
RD (+)
R2I + +
RD (–)
R2I – –
CN1
CN9
IC10
Gate array
D2O
A15
A15
ERROR
CS (+)
R1I + +
CS (–)
R1I – –
RS (–)
RS (+)
ACK
D1O
B15
B15
D2EN
A10
A10
D2I
B12
B12
D2O
IC5
D2O
CPU
D1EN
SD (–)
SD (+)
RXD0
D1O
D1I
B14
D1O
B14
TXD0
RXD1
MC34051
RS422A Interface PCB
Main PCB
Fig. 2-3 RS422A Interface
IC1 operates as the RS422A driver and receiver.
Data flow from host to printer: IC1 receives serial data from the host computer via RD, converts the signal voltage from
RS422A level to TTL level, and passes the result to the CPU. The CPU converts the serial data to parallel and stores it
into buffer memory.
Data flow from printer to host: The CPU generates data, converts it into serial form, then passes it to IC1. IC1 converts
the signal voltage from TTL level to RS422A level, then outputs the result over the SD line.
The CS line is hardware-connected, but the connection is not recognized by software. (The printer does not monitor the
signal.)
– 22 –
THEORY OF OPERATION
2-1-3. Parallel interface
CN3
CN1 CN9
IC10
IC5
DATA 1
DATA 2
DARA 3
DATA 4
DATA 5
DARA 6
DATA 7
DATA 8
STROBE
BUSY
ACK
A4
A4
B4
B4
A5
A5
B5
B5
A6
A6
B6
B6
A7
A7
B7
B7
A13
A13
A12
A12
B12
B12
A10
A10
A11
A11
B11
B11
CD0
CD1
CD2
CD3
CD4
CD5
CD6
CD7
CSTB
BUSY
ACK
CPU
ERROR
SELECTED
PAPER OUT
ERROR
SELECT
POUT
Gate array
LS05
IC1
Parallel Interface PCB
Main PCB
Fig. 2-4 Parallel Interface
The host computer sends eight bits of parallel data to CN3 when the printer is ready (when BUSY is LOW).
The data passes through the interface PCB and gate array, then moves into the CPU.
Printer signals from the CPU (ACK, ERROR, SELECTED, PAPER OUT, etc.) pass through the gate array and are output
over the appropriate connector pins.
– 23 –
THEORY OF OPERATION
2-2. Editing and Printing
2-2-1. Editing
The CPU reads data sequentially from RAM and edits it in accordance with program instructions stored in EPROM. The
edited data undergoes parallel-to-serial conversion in the gate array, and is then output to the thermal head’s drive
controller.
2-2-2. Thermal head
The thermal head contains 640 heat elements. Printing is carried out by switching these elements ON or OFF as required.
Note that Line Mode supports 600-dot printing only. During Line Mode operation, therefore, the logic always sends OFF
data to elements 1 to 20 and 621 to 640.
The thermal head contains a dedicated drive controller. The controller consists of a shift register, a latch circuit, and a
driver circuit, as illustrated below. The drive controller receives serial data (SI) from the drive control board in sync with
the CLOCK signal. The controller latches the incoming data (LATCH), then outputs it to the heat elements in sync with
the trailing edge of the STROBE signals. A data value of LOW corresponds to a heat-element value of ON.
COM
STROBE5
STROBE4
STROBE3
STROBE2
STROBE1
Latch
LATCH
SI
Shift Register
CLOCK
Fig. 2-5 Thermal-Head Drive Circuit
– 24 –
THEORY OF OPERATION
CLOCK
SI
LATCH
t
STROBE1
STROBE2
STROBE3
STROBE4
STROBE5
24V
COMMON
Fig.2-6 Timing Chart
2-2-3. Head current control
Heat buildup in the head during operation can cause print quality to degrade. To maintain uniform quality, the printer
varies the energizing time (time that STROBE remains LOW) in accordance with the head temperature.
The thermal head’s surface temperature is calculated based on the resistance value of an attached thermistor. Energizing
time is reduced at higher temperatures, as indicated in the figure 2-6.
STROBE1, STROBE2, STROBE3
STROBE4, STROBE5,
Head Energizing Time
t (µsec)
t
t
600
500
400
300
10
20
30
40
Thermistor Temp. (°C)
Fig. 2-7 Head Energizing Control
– 25 –
50
THEORY OF OPERATION
2-3. Feed-Motor Drive Circuit
The printer employs a 4-phase step motor (phase 1-2 excitation) to implement paper feed. The motor rotates through a
certain angle each time it receives a pulse from the drive circuit. The following diagram illustrates the phase 1-2 excitation
method. Diagram 2-8 shows the feed-motor drive circuit.
ON
1
ON
ON
2
ON
3
ON
4
Step
1
2
3
4
5
6
7
8
Forward Feed
Reverse Feed
Fig. 2-8 Motor Control by Phase 1-2 Excitation
IC5
CPU
+24V +5V
CN4
D1
DQ2
1
PA4
Q2
B TA1
Paper-feed motor
2
3
1
PA0
4
PA2
5
PA3
M
3
2
4
6
PA1
E
M-GND
Fig. 2-9 Feed-Motor Drive Circuit
Voltage to the motor is controlled to produced the required action, as follows.
Mode
Operating
Idle
Voltage
Action
VM (+24V)
VL (+5V)
Drives the motor
VL (+5V)
Holds the motor
Voltage is controlled by PA4 of the CPU, which goes HIGH or LOW to switch transistors DQ2 and Q2 ON or OFF. When
Q2 is ON, the motor receives +24V (VM). When Q2 is OFF, +5V is supplied to the motor via diode D1.
– 26 –
THEORY OF OPERATION
2-4. Power-On Reset Circuit
Immediately following power-on the printer executes a power-on reset, initializing all circuit elements. The power-on
reset serves as protection against operational errors. The power-on RESET signal is maintained for approximately 160ms.
The reset circuit is illustrated below.
+5V
+5V
IC10
+5V
+5V
IC4
IC5 : CPU
VCC
RESET
CPU
CD
RES
RESET
Gate
array
RESO
+
C2
GND
RESET IC
DD3
VCC
Back-up
Circuit
S-RAM
IC1
Fig. 2-10 Power-On Reset Circuit
1
At power on, voltage-detector circuit IC4 (M51953BL) outputs a LOW signal from its OUT terminal. The signal
lasts for approximately 160ms, as determined by capacitor C2 (0.47µF):
T = 0.34 × C2 (pF) [µs] = 160ms
2
The LOW signal resets the CPU and the mechanism drive circuits, and sets S-RAM into backup state.
– 27 –
THEORY OF OPERATION
2-5. +5V Line Voltage Detector Circuit
The voltage-detection IC (IC4 in Fig. 2-10) detects momentary drops or unstable levels in the +5V line voltage. IC4
operation is illustrated by the equivalence circuit shown below.
VCC
1
SµA typ
R1
5
–
OUT
–
+
R2
1.25V
3
GND
4
Cd
Fig. 2-11 Equivalence Circuit for Voltage Detecting IC
Fig. 2-11 shows the operational timing. If the +5V line voltage falls below 4.25V, the IC produces a reset signal at its
OUTPUT terminal, resetting the CPU and the gate array.
VCC Voltage
4.25V
0.8V
t
Output
Voltage
td
td
t
td = 0.34 × Cd (pF) [µs]
Fig. 2-12 Operation Timing Chart
– 28 –
THEORY OF OPERATION
3.
Printer Mechanism
3-1. Thermal Head
The TSP400 printers employ thermal line printing. The thermal head consists of a horizontal line of 640 heat elements.
These elements print one line of dots at a time as the paper passes over the head. The head is fixed in position; only the
paper moves.
The printer prints a dot by heating the corresponding heat element. The heated element causes a chemical reaction in the
coloring layer of the thermal paper, resulting in the formation of a visible dot.
Thermal head
Heat element
Coloring layer
Thermal paper
Printed point
Platen
Fig. 2-13 Principle of Thermal Printing
3-2. Paper-Feed Mechanism
The paper-feed mechanism is comprised of the paper-feed motor, gear train, platen, and thermal head. The paper-feed
motor drives the gear train, which in turn rotates the platen. The platen carries the thermal paper past the thermal head.
The paper-feed motor is a PM (permanent magnet) type, 4-phase 48-pole step motor. A single step feeds the paper
approximately 0.125mm.
Thermal head
Thermal paper
Gear train
Platen
Paper-feed motor
Fig. 2-14 Paper-Feed Mechanism
– 29 –
THEORY OF OPERATION
3-3. Detectors
(1)
Paper-Out Detector
The paper-out detector is located at the paper entry slit. The detector consists of a reflective photosensor. The
photosensor’s phototransistor remains ON while paper is present. It goes OFF when paper runs out, generating
output of a paper-out signal.
(2)
Black-Mark Detector
This detector senses black marks indicating print start positions. The detector is useful only with specially marked
paper. Like the paper-out detector, the black-mark detector consists of a reflective photosensor. The photosensor’s
phototransistor goes OFF when a black mark appears.
R
R
Paper
GND
+5V
+5V
Detection signal
Detection signal
R
Black mark
R
(Reflective photosensor)
(Reflective photosensor)
Fig. 2-15 Paper-Out Detector
(3)
Paper
GND
Fig. 2-16 Black-Mark Detector
Label Detector
The transmissive detector is used to detect print-start positions for labels. It operates by detecting the difference
in light transmission between backing-only and backing-plus-label portions of the paper.
Light
Light
Label paper
Quantity of
transmitted light
Backing paper
Quantity of
transmitted light
Fig. 2-17
5V
Paper
Detection signal
GND
Fig. 2-18 Label Detector
– 30 –
THEORY OF OPERATION
(4)
Head-Up Detector
This detector consists of a leaf switch indicating whether the head is closed (in contact with the platen) or open
(separated from the platen). The leaf switch is closed when the head is closed; it opens when the head is opened.
+5V
R
Detection signal
Leaf switch
GND
Fig. 2-19 Head-Up Detector
– 31 –
CHAPTER 3
PARTS REPLACEMENT AND RELATED ADJUSTMENTS
This chapter describes disassembly and reassembly procedures.
Please take note of the following.
1. ALWAYS disconnect the power cord from the AC outlet before beginning a disassembly or reassembly
procedure.
2. Except where otherwise stated, the reassembly procedure is the reverse of the disassembly procedure.
3. Coat screw heads with locking sealant after completion of reassembly.
4. Refer to Chapter 4 Section 2 for important information about lubrication requirements.
Note : The printer has no adjustable parts.
1.
Upper Casing Unit ............................................................................................... 35
2.
Control-Panel Board ........................................................................................... 36
3.
Printer Mechanism .............................................................................................. 37
4.
Main PCB, Interface PCB .................................................................................... 38
5.
Power Unit ........................................................................................................... 39
6.
Fuse ...................................................................................................................... 39
7.
Printhead Unit ...................................................................................................... 40
8.
Feed Motor Assembly ......................................................................................... 40
9.
Detectors .............................................................................................................. 41
10.
Label sensor ..................................................................................................................... 41
3
PARTS REPLACEMENT
– 34 –
PARTS REPLACEMENT
1.
<TSP412D>
(1) Disconnect the power cord from the AC outlet.
(2) Remove:
• Upper cover 1
• Two tapping screws 2
• Upper casing unit 3
• Pull forward and remove.
• Connector 4
• Screw 5
1
3
Upper Casing Unit
2
4
5
<TSP442D>
(1) Disconnect the power cord from the AC outlet.
(2) Remove:
• Upper cover 1
• Two tapping screws 2
• Upper casing unit 3
Pull forward and remove.
• Connector 4
1
3
2
4
– 35 –
PARTS REPLACEMENT
2.
Control-Panel Board
(1)
Remove:
• Upper casing unit (See 1. above.)
• Two tapping screws 1
• Front cover 2
• Two tapping screws 3
• Control-panel board 4
2
4
3
1
– 36 –
PARTS REPLACEMENT
3.
<TSP412D>
(1) Remove:
• Upper casing unit (See 1. above.)
• One tapping screw 1
• ROM cover 2
• Eight tapping screws 3
• Four connectors 4
• Screw 5
• Printer mechanism 6
3
3
2
Printer Mechanism
1
3
4
6
4
5
3
3
2
4
1
3
6
8
5
<TSP442D>
(1) Remove:
• Upper casing unit (See 1. above.)
• One tapping screw 1
• ROM cover 2
• Eight tapping screws 3
• Five connectors 4
• Two tapping screws 5
• Cutter unit 6
• Screw 7
• Printer mechanism 8
4
7
4
– 37 –
PARTS REPLACEMENT
4.
<TSP412D>
(1) Remove:
• Upper casing unit (See 1. above.)
• Six tapping screws 1
• Mechanism chassis 2
• Six connectors 3
• Interface cover 8
• Three screws 4
• Interface PCB 5
• Four screws 6
• Main PCB 7
1
1
1
3
3
2
3
6
3
7
6
4
6
Main PCB, Interface PCB
8
5
<TSP442D>
(1) Remove:
• Upper casing unit (See 1. above.)
• 1 screw
• Four tapping screws 1
• Mechanism chassis 2
• Seven connectors 3
• Interface cover 8
• Three screws 4
• Interface PCB 5
• Four screws 6
• Main PCB 7
1
1
1
3
3
2
6 1
3
3
6
4
6
8
7
5
– 38 –
PARTS REPLACEMENT
1
5.
Power Unit
(1)
(2)
Disconnect the power cord from the AC outlet.
Remove:
• Upper casing unit (See 1. above.)
• Three screws (See 4. above.)
• Interface PCB (See 4. above.)
• Screw 1
• Four screws 2
• Lower casing chassis 3
• Connector 4
• Two tapping screws 5
• Shield chassis (A) 6
• Connector 7
• Four screws 8
• Power unit 9
• Screw 0
• Earth plate (A) A
6.
Fuse
(1)
Remove shield chassis A, according to procedure
given in 5. above.
Check fuse F1. 1
If the fuse is blown, replace with the following.
6
5
7
8
4
8
8
9
A
0
2
3
2
(2)
1
AC Voltage
120V
220-240V
F1
5TT5A-125V
EAK3.15A250V
If the replacement fuse also blows out, replace the
power unit or check the main logic board.
– 39 –
PARTS REPLACEMENT
4
7.
Printhead unit
(1)
(2)
Remove the upper casing unit. (See 1. above.)
Pull the pressure stay 1 forward to open the head
frame unit 2.
Slide the head clamp 3 in the direction indicated by
the arrow. Remove the printhead unit 4.
Remove the head connector 5.
(3)
2
(4)
5
1
Note : Be careful to avoid damaging the heat elements
when installing the replacement unit.
3
8.
Feed Motor Assembly
(1)
Remove:
• Printer mechanism (See 3. above.)
• Two tapping screws 1
• Feed motor assembly 2
1
2
– 40 –
PARTS REPLACEMENT
9.
Detectors
(1)
Remove:
• Printer mechanism (See 3. above.)
• Two screws 1
• Paper-out and black-mark detectors 2
• Tapping screw 3
• Head-up detector 4
4
3
1
2
10. Label sensor
(1)
4
5
1
2
2
3
1
– 41 –
Remove:
• Two E-rings 1
• Two oiless bushings 2
• Support stay 3
• One tapping screw 4
• Label sensor 5
PARTS REPLACEMENT
– 42 –
CHAPTER 4
MAINTENANCE AND LUBRICATION
1.
2.
Maintenance ........................................................................................................ 45
1-1.
Cleaning ................................................................................................................. 45
1-2.
Checks ................................................................................................................... 45
Lubrication ........................................................................................................... 46
2-1.
Lubricants .............................................................................................................. 46
2-2.
Application Method ............................................................................................... 46
2-3.
Lubrication Points ................................................................................................. 46
4
MAINTENANCE AND LUBRICATION
– 44 –
MAINTENANCE AND LUBRICATION
1.
Maintenance
Proper maintenance is necessary to maintain printer performance and forestall potential problems. Please carry out
maintenance as described below.
1-1. Cleaning
(1)
Surface dirt
Clear away dirt with a soft cloth. If necessary, apply a small quantity of alcohol to the cloth to improve cleaning
power. NEVER use thinner, trichlene, or ketone solvents, as these can cause damage to plastic components.
When cleaning, take care to avoid damaging or moistening of electronic parts, mechanical parts, and wires.
(2)
Internal dust
For best results, use an electric vacuum cleaning device to remove dust from the inside of the printer. Note that such
cleaning may also remove lubrication; when you have finished cleaning, check lubrication levels and apply
lubricant as necessary.
1-2. Checks
There are two types of maintenance checks. Simple “daily checks” can be performed by users during the course of daily
operation. “Periodic checks” must be carried out by qualified service personnel.
(1) Daily checks
• Check whether dirt or other foreign matter has worked its way into the printer, and remove as necessary.
• Check the thermal head for excessive dirt. If the head is very dirty, clean it with a cotton stick or a soft cloth soaked
in alcohol.
(2) Periodic checks
Periodic checks and lubrication should be carried out once every six months or once every million lines of printing.
• Check the integrity of springs.
• Clear dust from areas around the detectors.
– 45 –
MAINTENANCE AND LUBRICATION
2.
Lubrication
Proper lubrication is essential for maintaining the printer’s performance level and preventing breakdowns or other
problems.
2-1. Lubricants
Choice of lubrication can significantly affect the printer’s performance, longevity, and low-temperature characteristics.
We recommend the following lubricant for the TSP400 series.
Type
Name
Manufacturer
Grease
Molykote EM
Dow Corning
2-2. Application Method
If you are lubricating parts during disassembly or reassembly, be sure to wash or wipe the parts thoroughly to remove all
dirt and dust prior to lubricating.
Remember that cleaning can remove necessary lubrication. Always lubricate after cleaning, disassembly, or replacement.
2-3. Lubrication Points
Apply lubricants at the following locations. (Refer to Diagram 4-1.)
No.
Location
1
Contact area of pressure bar and pressure pin
2
Contact area of gear 15×50×0.5 and gear shaft
3
Contact area of gear 58×0.5 and gear shaft
4
Contact area of gear 15×50×0.5 and PF motor gear
5
Contact area of gear 58×0.5 and platen gear
6
Contact area of head stay and head base frame
7
Contact area of head clamp and clamp pin
8
Contact area of head clamp and head stay R
9
Contact area of lever and lever shaft (TSP442)
Note 1 : Paper debris on cutter blade can cause paper jams. Clean away debris by wiping with alcohol, then reapply
lubricant.
– 46 –
MAINTENANCE AND LUBRICATION
1
8
B
7
1
6
6
C
C
A
9
D
B
A
D
9
4
2
3
5
Fig. 4-1 Lubrication Points
– 47 –
MAINTENANCE AND LUBRICATION
– 48 –
CHAPTER 5
PARTS LIST
READING THE LISTS
(1)
(2)
(3)
(4)
(5)
(6)
(7)
DRWG. NO.
Corresponds to the drawing number or to the silk-screened number on the board to which the part is mounted.
REVISED EDITON MARK
This column shows a revision number.
Parts that have been added in the revised edition are indicated with “#”.
Parts that have been abolished in the revised edition are indicated with “*”.
#1 : First edition → Second edition
#2 : Second edition → Third edition
*1 : First edition → Second edition
*2 : Second edition → Third edition
PART NO.
Part identification number. Always indicate this number clearly when ordering a part.
Parts described as “NPN” have no parts number and are not in stock, i.e., unavailable.
PART NAME
Name of part. Always include the name (as well as the part No.) when ordering the part.
QTY
Indicates the number of units of the part used within the assembly.
REMARKS
This column is used for general comments. It also indicates EPROM seal numbers. A “*” within a seal number
indicates the version number.
RANK
“S” indicates that the part is a “service part” that should always be kept in stock for maintenance purposes.
1. Printer Assembly .............................. 50
6. RS422A Interface Board .................. 68
1-1. Disassembly Drawing ................... 50
A. TSP412D .................................... 50
B. TSP442D .................................... 51
1-2. Parts List ......................................... 52
6-1. Circuit Diagram ...............................68
6-2. Parts List ......................................... 69
2. Printer Mechanism Assembly ......... 54
7. Centronics Interface Board ............. 70
7-1. Circuit Diagram ...............................70
7-2. Parts List ......................................... 71
2-1. Disassembly Drawing ................... 54
2-2. Parts List ......................................... 55
8. Control Panel Board ........................ 72
3. Connector Wiring Diagram .............. 56
8-1. Circuit Diagram ...............................72
8-2. Parts List ......................................... 73
A. RS-232C Interface Type .............. 56
B. RS-422A Interface Type .............. 57
C. Parallel Interface Type ................ 58
4. Main Logic Board ............................. 59
4-1. Circuit Diagram ............................... 59
4-2. Parts List ......................................... 63
5. RS232C Interface Board .................. 66
5-1. Circuit Diagram ............................... 66
5-2. Parts List ......................................... 67
9. Paper-Out Detector Board ............... 74
9-1. Circuit Diagram ...............................74
9-2. Parts List ......................................... 74
10. Label Sensor Board ......................... 74
10-1. Circuit Diagram ...............................74
10-2. Parts List ......................................... 74
5
1.
Printer Assembly
1-1. Disassembly Drawing
A. TSP412D
27
B
43
41
32
25
17
30 57
K
24
A
41
26
18
47
L
C
29
31
47
48
K
DF
E
22
J
39
53
39
48
I
58
21
42
13
15
12
14
57
D
12
20
M
H
A
I
T
M
42
7
10
49
54
E
F
16
57
42
G
56
C
47
7
42
22
H
58
60
23
42
57
B
59
28
23
50
40
55
50
G
19
J
7
7
3
N
L
T
49
R
49
O
9
46
6
Q
54
41
R
2
N
P
P
5
51
4
49
33
Q
45
O
1
44
45
8
– 50 –
B. TSP442D
27
B
45
41
32
25
28
17
52
K
53
29
24
A
38
41
52
36
34
23
22
35
48
48
K
DF
E
23
57
B
47
L SC
26
37
18
47
58
58
56
39
60 58
52
S
I
48
21
42
13
15
12
47
14
57
D
C
20
49
H
50
42
7
57
M
54
E
F
M
10
42
G
56
12
16
7
42
22
H
A
I
T
40
50
55
50
G
19
7
7
3
N
L
R
49
O
9
46
6
Q
41
54
5
51
R
2
N
P
P
T
49
4
49
33
45
1
44
44
45
8
– 51 –
Q
O
1-2. Parts List
Printer Assembly
DRWG.NO. REV. PARTS NO.
1
2
3
4
5
6
7
8
9
10
12
13
14
*2
#2
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
*2
#2
87391070
87393030
87393090
82011481
87393040
87393070
87393080
04991220
82011490
04991254
80991601
87391080
NPN
33750010
37407000
37403800
37407800
37407810
37407820
32021010
32021110
33020200
30721030
30721021
30721040
32010211
32912010
32912011
38405000
32041010
83201000
83903931
83025392
87390610
30061010
83025420
83025481
30071010
82902290
80701770
33020210
32790000
80040151
82902430
82040621
82902460
82040611
04991401
09990527
09990723
09990723
01903077
01903077
00930605
00930609
PARTS NAME
LOWER CASE CHASSIS UNIT
BCP4
POWER SUPPLY UNIT SLS-060P-50
POWER SUPPLY UNIT SLS060PH-50A
SHIELD CHASSIS A
BCP4
CORD SET UNIT US
BCP4
CORD SET UNIT EC
BCP4
CORD SET UNIT UK
BCP4
CORD BUSHING SR-5N-4
SHIELD CHASSIS B
BCP4
CORD CLAMP EDS-1208U
RUBBER FOOT
8340
LOWER CASE UNIT
BCP4
BOARD CHASSIS
TSP4
BOARD RAIL
TSP4
MAIN LOGIC BOARD UNIT
TSP4
IF PLATE RS232 UNIT
TSP4
RS232C IF BOARD UNIT
TSP4
RS422 IF BOARD UNIT
TSP4
PARALLEL IF BOARD UNIT
TSP4
SERIAL IF PLATE
TSP4
PARALLEL IF PLATE
TSP4
INTERFACE COVER
TSP4
CABLE UNIT 12X220CC
TSP4
CABLE UNIT B
TSP4
CABLE UNIT A
TSP4
MECHANISM BASE CHASSIS
TSP4
ROM COVER
TSP4
ROM COVER
TSP4
TMP412-24
HOLDER ANGLE
TSP4
ROLL PAPER BUSHING
BMP4
LABEL HOLDER 3.25
BMP4
UPPER CASE
BCP4
CONTROL PANEL BOARD ASSY
BCP4
OPERATION SHEET
TSP4
FRONT COVER A
BCP4
FRONT COVER B
BCP4
BRAND SEAL
TSP4
CUTTER
BCP4
WIRE 18UL1007BRN145TT
UPPER COVER B
TSP4
EARTH PLATE A
TSP4
CUTTER 4010
BCP4
CUTTER HOLDER
BCP4
CUTTER PAPER GUIDE B
BCP4
PAPER GUIDE CLAMP
BCP6
CUTTER PAPER GUIDE A
BCP4
SCREW DBLC-J25SAF
BOARD SPACER RSPS-8L
FERRITE CORE TFC-23-11-14
FERRITE CORE TFC-23-11-14
SCREW TAT 3-5 CT-FL
SCREW TAT 3-5 CT-FL
SCREW TAT 3-6 FS
SCREW TAT 3-6 CT
– 52 –
Q'TY
1
1
1
1
1
1
1
1
1
4
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
3
10
11
2
4
REMARKS
RANK
US
EC,UK
S
S
US
EC
UK
S
S
S
S
S
RS232C
RS232C
RS422A
PARALLEL
RS232C,RS422A
PARALLEL
S
S
S
S
S
EC,UK
US
S
ACCESSORY
S
S
S
TSP412
TSP442
TSP412
TSP412
S
S
TSP442
TSP442
TSP442
TSP442
TSP442
RS232C,RS422A
US
EC,UK
TSP412
TSP442
S
S
S
S
S
S
S
Printer Assembly
DRWG.NO.
REV. PARTS NO.
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
-
#1
#1
#2
#2
#2
#2
#2
#2
#2
#2
#2
00930803
01903018
01903059
01903069
01903069
01903099
01914035
01914036
00630404
00930803
00930500
04991257
09990713
00930603
00930603
00630504
01903085
30091010
09990723
09990728
04991204
PARTS NAME
SCREW TAT 3-8 PT
SCREW TR 3-6 WS/WF
SCREW TR 3-5 FL
SCREW TAT 3-5 ST-FL
SCREW TAT 3-5 ST-FL
SCREW TR 3-4 WS
SCREW TAT 4-10 PT-FL
SCREW TR 4-5 WS
SCREW TR 3-4
SCREW TAT 3-8 PT
SCREW TAT 3-5 ST
CORE STOPPER TFP2014-V
FERRITE CORE TRCC-16-8-16 CASE
SCREW TAT 3-6 PT
SCREW TAT 3-6 PT
SCREW TR 3-5
SCREW TAT 3-7 WS
TENSION SHEET
TSP2
FERRITE CORE TFC-23-11-14
FERRITE CORE TFC-20-10-10
FASTENER T18S
– 53 –
Q'TY
6
4
6
2
4
5
4
1
7
2
2
1
2
6
4
3
1
1
1
1
1
REMARKS
RANK
S
S
S
S
S
S
S
S
S
S
S
TSP412
TSP442
TSP442
EC,UK
TSP412
TSP442
S
S
S
S
TSP412
ACCESSORY
ACCESSORY
ACCESSORY
:EC
:EC
:EC
2.
Printer Mechanism Assembly
2-1. Disassembly Drawing
15-16
15-10
15-6
15-12
15-7
15-13
15-14
15-5
15-14
15-8
15-14
15-12
15-7
15-4
15-3
15-14
15-13
15-9
15-11
15-10
B
15
15-16
34
15-13
15-6
15-15
25
29
15-9
15-2
29
C
C
15-1
A
14
11
6
15-13
9
13
24
D
15-17
33
32
44
33
5
10
33
B
33
37
A
40
8
1
D
13
33
24
32
39
45
8
7
30
2
12
39
4
3
41
38
43
– 54 –
31
2-2. Parts List
DRWG.NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15-1
15-2
15-3
15-4
15-5
15-6
15-7
15-8
15-9
15-10
15-11
15-12
15-13
15-14
15-15
15-16
15-17
25
29
30
31
32
33
34
37
38
39
40
41
42
43
44
45
Printer Mechanism
REV. PARTS NO.
*2
#2
*1
#1
*1
#1
*1
#1
*1
#1
*1
#1
*1
#1
#1
#1
NPN
37412300
37417000
83100460
87340390
31375210
31375211
33102210
80203041
33910020
37417010
33910030
33910031
33903010
33490010
87343110
37419000
87340410
37410010
81360850
31303010
82902330
81370910
09991391
82401370
82401360
80994252
04310401
80511070
80510840
80511060
30510410
04020015
04020016
04991204
02040301
09991372
80705030
80705031
80520950
30520210
04012003
04020010
04020015
04020016
04991204
00920503
00630404
00930403
00930803
01914035
00930609
30721010
01903090
31361010
PARTS NAME
FRAME ASSY
PF MOTOR ASSY
TMP4
REFLECT SENSOR BD UNIT
TMP4
IDLER GEAR 15X50X0.5
HEAD DETECTOR ASSY
BMP8
PLATEN
TMP4
PLATEN
TMP4
GEAR 28X0.5
TMP4
DRIVE SHAFT BEARING
MP300
PAPER GUIDE A
TMP4
TRANSMIT SENSOR BD UNIT
TMP4
PAPER GUIDE B
TMP4
PAPER GUIDE B
TMP4
FRICTION PLATE
TMP4
HEAD POSITION LEVER
TSP4
HEAD UNIT
BMP4
HEAD UNIT
TMP4
HEAD FRAME UNIT
BMP4
HEAD FRAME UNIT
TMP4
PAPER GUIDE ROLLER
BMP4
HEAD UNIT PIVOT SHAFT
TSP4
HEAD CLAMP
BMP4
PRESSURE STAY
BMP4
HEAT-SHRINK TUBE A-6.0 GRN
PRESSURE LEVER
BMP4
HEAD STOPPER LEVER
BMP4
GUARD SHEET
BMP4
OILESS BUSHING F4X7X3
SPRING E040-040-0159
SPRING E055-060-0180
SPRING E060-060-0316
SPRING E065-070-0238
STOP RING SE3.0
STOP RING SE4.0
FASTENER T18S
FLANGED NUT NHW3
HEAT-SHRINK TUBE 4.0
CABLE UNIT 26X265CC
BMP4
CABLE UNIT 26X290CC
BMP4
SPRING C075-080-0187
SPRING C075-080-0165
ROLL PIN SP2.0X8
STOP RING SE2.0
STOP RING SE3.0
STOP RING SE4.0
FASTENER T18S
SCREW TAT 2-5 CT
SCREW TR 3-4
SCREW TAT 3-4 CT
SCREW TAT 3-8 PT
SCREW TAT 4-10 PT-FL
SCREW TAT 3-6 CT
CABLE UNIT
TMP4
SCREW TAT 3-8 CT-FL
SUPPORT STAY
TMP4
– 55 –
Q'TY
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
2
2
1
2
2
2
2
3
2
1
1
1
2
2
1
1
2
7
2
1
2
2
1
1
1
1
1
1
REMARKS
RANK
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
3.
Connector Wiring Diagram
A. RS-232C Interface Type
RS232C I/F BOARD
CONTROL BOARD
CN3
CN1
PRINTER MECHANISM
CN9
CN1
CN1
1
F-GND
NC
A1
A1
DIN9
GND
1
1
2
TXD
NC
A2
A2
DIN11
PE
2
2
3
RXD
VVR
A3
A3
VVR
MARK
3
3
4
RTS
DIN1
A4
A4
DIN1
Vcc(+5)
4
4
5
CTS
DIN3
A5
A5
DIN3
LABLE
5
CN1
6
NC
DIN5
A6
A6
DIN5
GND
6
1
7
GND
DIN7
A7
A7
DIN7
LED
7
2
8
NC
GND
A8
A8
GND
9
NC
Vcc(+5V)
A9
A9
Vcc(+5V)
10
NC
NC
A10
A10
ERR
11
RCH
NC
A11
A11
SLCT
HUP DTCT
1
HUP DTCT
2
MARK
DETECTOR
PAPER OUT
DETECTOR
3
LABEL DETECTOR
HADE UP DETECTOR
CN2
12
NC
NC
A12
A12
BUSY
13
GND
DIEN
A13
A13
STB
14
FAULT
GND
A14
A14
GND
15
MP-TXD
RXD
A15
A15
RXD
LFCMN
1
16
MP-DTR
NC
A16
A16
ID0
LFCMN
2
17
NC
ID2
A17
A17
ID2
LFø1
3
18
NC
GND
A18
A18
GND
LFø3
4
19
NC
PEXT1
A19
A19
PEXT1
LFø4
5
20
DTR
VEXT
A20
A20
VEXT
LFø2
6
21
NC
NC
B1
B1
DIN10
22
NC
NC
B2
B2
DIN12
23
NC
GND
B3
B3
GND
24
NC
DIN2
B4
B4
DIN2
25
NC
DIN4
B5
B5
DIN4
DIN6
B6
B6
DIN6
DIN8
B7
B7
DIN8
GND
B8
B8
GND
Vcc(+5V)
B9
B9
Vcc(+5)
COM(+24V)
CN4
PAPER FEED MOTOR
PERIPHERAL UNIT
ø1
ø2
1
1
1
F-GND
NC
B10
B10
NMI
COM(+24V)
2
2
2
2
PEXT1
FAULT
B11
B11
PE
COM(+24V)
3
3
3
3
VEXT
DTR
B12
B12
ACK
GND
4
4
4
4
VEXT
GND
B13
B13
GND
GND
5
5
5
5
PEXT2
TXD
B14
B14
TXD
GND
6
6
6
6
PSW
CTS
B15
B15
CTS
SI
7
7
ID1
B16
B16
ID1
SO
8
8
GND
B17
B17
GND
CLK
9
9
PSWIN
B18
B18
PSWIN
GND
10
10
PEXT2
B19
B19
PEXT2
LAT
11
11
VEXT
B20
B20
VEXT
GND
12
12
STB5
13
13
VDD(+5V)
14
14
STB3
15
15
MAGNET
CORE
(1 TURN)
[CN8]
1
Vcc(+5V)
STB4
16
16
2
PEXT1
STB1
17
17
3
VP(+24V)
STB2
18
18
4
PSWIN
TM1
19
19
5
GND
TM2
20
20
GND
21
21
GND
22
22
GND
23
23
OPERATION PANEL
CN1
CN7
ø4
CN6
1
CN2
M
ø3
1
1
GND
COM(+24V)
24
24
2
2
COPEN
COM(+24V)
25
25
3
3
PF-SW
COM(+24V)
26
26
4
4
OL-SW
5
5
PSW1
6
6
PSW2
7
7
PSW
CUTSW
1
8
8
OL-LED
CUTSW
2
9
9
PO-LED
M(–)
3
10
10
HU-LED
M(+)
4
11
11
ER-LED
12
Vcc(+5V)
THERMAL HEAD
CUTTER UNIT
CN5
(TSP442 Series only)
12
M
MAGNET
CORE
(1 TURN)
POWER SUPPLY UNIT
CN3
[CN8] is not connected yet.
– 56 –
CN2
CN1
VP(+24V)
1
1
L
1
VP(+24V)
2
2
NC
2
NC
3
3
N
3
P-GND
4
4
NC
4
P-GND
5
FG
5
MAGNET
CORE
(1 TURN)
B. RS-422A Interface Type
RS422A I/F BOARD
CONTROL BOARD
CN1
CN3
PRINTER MECHANISM
CN9
CN1
CN1
1
F-GND
DIN9
A1
A1
DIN9
GND
1
1
2
NC
DIN11
A2
A2
DIN11
PE
2
2
3
NC
VVR
A3
A3
VVR
MARK
3
3
4
NC
DIN1
A4
A4
DIN1
Vcc(+5)
4
4
5
NC
DIN3
A5
A5
DIN3
LABLE
5
CN1
6
NC
DIN5
A6
A6
DIN5
GND
6
1
7
GND
DIN7
A7
A7
DIN7
LED
7
2
8
NC
GND
A8
A8
GND
9
SD(+)
Vcc(+5V)
A9
A9
Vcc(+5V)
10
SD(–)
DOEN
A10
A10
ERR
11
NC
NC
A11
A11
SLCT
HUP DTCT
1
12
NC
NC
A12
A12
BUSY
HUP DTCT
2
13
GND
DIEN
A13
A13
STB
14
FAULT
GND
A14
A14
GND
15
NC
RD
A15
A15
RXD
LFCMN
1
16
NC
ID0
A16
A16
ID0
LFCMN
2
17
RD(+)
ID2
A17
A17
ID2
LFø1
3
18
RD(–)
GND
A18
A18
GND
LFø3
4
19
CS(+)
PEXT1
A19
A19
PEXT1
LFø4
5
20
NC
VEXT
A20
A20
VEXT
LFø2
6
21
NC
DIN10
B1
B1
DIN10
22
NC
DIN12
B2
B2
DIN12
23
CS(–)
GND
B3
B3
GND
24
RS(+)
DIN2
B4
B4
DIN2
25
RS(–)
DIN4
B5
B5
DIN4
DIN6
B6
B6
DIN6
DIN8
B7
B7
DIN8
GND
B8
B8
GND
Vcc(+5V)
B9
B9
Vcc(+5)
COM(+24V)
MARK
DETECTOR
PAPER OUT
DETECTOR
3
LABEL DETECTOR
HADE UP DETECTOR
CN2
CN4
PAPER FEED MOTOR
PERIPHERAL UNIT
ø1
ø2
1
1
1
F-GND
NC
B10
B10
NMI
COM(+24V)
2
2
2
2
PEXT1
FAULT
B11
B11
PE
COM(+24V)
3
3
3
3
VEXT
RS
B12
B12
ACK
GND
4
4
4
4
VEXT
GND
B13
B13
GND
GND
5
5
5
5
PEXT2
SD
B14
B14
TXD
GND
6
6
6
6
PSW
CS
B15
B15
CTS
SI
7
7
ID1
B16
B16
ID1
SO
8
8
GND
B17
B17
GND
CLK
9
9
PSWIN
B18
B18
PSWIN
GND
10
10
PEXT2
B19
B19
PEXT2
LAT
11
11
VEXT
B20
B20
VEXT
GND
12
12
STB5
13
13
VDD(+5V)
14
14
STB3
15
15
MAGNET
CORE
(1 TURN)
[CN8]
1
Vcc(+5V)
STB4
16
16
2
PEXT1
STB1
17
17
3
VP(+24V)
STB2
18
18
4
PSWIN
TM1
19
19
5
GND
TM2
20
20
GND
21
21
GND
22
22
GND
23
23
OPERATION PANEL
CN1
CN7
1
1
GND
COM(+24V)
24
24
2
2
COPEN
COM(+24V)
25
25
3
3
PF-SW
COM(+24V)
26
26
4
4
OL-SW
5
5
PSW1
6
6
PSW2
7
7
PSW
CUTSW
1
8
8
OL-LED
CUTSW
2
9
9
PO-LED
M(–)
3
10
10
HU-LED
M(+)
4
11
11
ER-LED
12
Vcc(+5V)
12
THERMAL HEAD
CUTTER UNIT
CN5
(TSP442 Series only)
M
MAGNET
CORE
(1 TURN)
POWER SUPPLY UNIT
CN3
[CN8] is not connected yet.
– 57 –
ø4
CN6
1
CN2
M
ø3
CN2
CN1
VP(+24V)
1
1
L
1
VP(+24V)
2
2
NC
2
NC
3
3
N
3
P-GND
4
4
NC
4
P-GND
5
FG
5
MAGNET
CORE
(1 TURN)
C. Parallel Interface Type
PARALLEL I/F BOARD
CN3
CONTROL BOARD
CN1
PRINTER MECHANISM
CN9
CN1
CN1
1
STROBE
NC
A1
A1
DIN9
GND
1
1
2
DATA 1
NC
A2
A2
DIN11
PE
2
2
3
DATA 2
VVR
A3
A3
VVR
MARK
3
3
4
DATA 3
DIN1
A4
A4
DIN1
Vcc(+5)
4
4
5
DATA 4
DIN3
A5
A5
DIN3
LABLE
5
CN1
6
DATA 5
DIN5
A6
A6
DIN5
GND
6
1
7
DATA 6
DIN7
A7
A7
DIN7
LED
7
2
8
DATA 7
GND
A8
A8
GND
9
DATA 8
Vcc(+5V)
A9
A9
Vcc(+5V)
10
ACK
ERROR
A10
A10
ERR
11
BUSY
SLCT
A11
A11
SLCT
HUP DTCT
1
12
PE
BUSY
A12
A12
BUSY
HUP DTCT
2
13
SLCT
STB
A13
A13
STB
14
NC
GND
A14
A14
GND
15
NC
NC
A15
A15
RXD
LFCMN
1
16
GND
ID0
A16
A16
ID0
LFCMN
2
MARK
DETECTOR
PAPER OUT
DETECTOR
3
LABEL DETECTOR
HADE UP DETECTOR
CN2
CN4
PAPER FEED MOTOR
PERIPHERAL UNIT
ø1
17
F-GND
NC
A17
A17
ID2
LFø1
3
18
Vcc(+5V)
GND
A18
A18
GND
LFø3
4
19
RETURN-GND
PEXT1
A19
A19
PEXT1
LFø4
5
20
RETURN-GND
VEXT
A20
A20
VEXT
LFø2
6
21
RETURN-GND
NC
B1
B1
DIN10
22
RETURN-GND
NC
B2
B2
DIN12
23
RETURN-GND
GND
B3
B3
GND
24
RETURN-GND
DIN2
B4
B4
DIN2
25
RETURN-GND
DIN4
B5
B5
DIN4
26
RETURN-GND
DIN6
B6
B6
DIN6
27
RETURN-GND
DIN8
B7
B7
DIN8
28
RETURN-GND
GND
B8
B8
GND
29
RETURN-GND
Vcc(+5V)
B9
B9
Vcc(+5)
COM(+24V)
1
1
30
RETURN-GND
INIT
B10
B10
NM1
COM(+24V)
2
2
31
INIT
PE
B11
B11
PE
COM(+24V)
3
3
ø2
CN6
32
ERROR
ACK
B12
B12
ACK
GND
4
4
33
EXT-GND
GND
B13
B13
GND
GND
5
5
34
CPL
NC
B14
B14
TXD
GND
6
6
35
NC
NC
B15
B15
CTS
SI
7
7
36
SLCT-IN
ID1
B16
B16
ID1
SO
8
8
GND
B17
B17
GND
CLK
9
9
GND
10
10
CN2
1
1
F-GND
PSWIN
B18
B18
PSWIN
2
2
PEXT1
PEXT2
B19
B19
PEXT2
LAT
11
11
3
3
VEXT
VEXT
B20
B20
VEXT
GND
12
12
4
4
VEXT
STB5
13
13
5
5
PEXT2
VDD(+5V)
14
14
6
6
PSW
STB3
15
15
[CN8]
MAGNET
CORE
(1 TURN)
1
Vcc(+5V)
STB4
16
16
2
PEXT1
STB1
17
17
3
VP(+24V)
STB2
18
18
4
PSWIN
TM1
19
19
5
GND
TM2
20
20
GND
21
21
GND
22
22
GND
23
23
OPERATION PANEL
CN1
CN7
1
1
GND
COM(+24V)
24
24
2
2
COPEN
COM(+24V)
25
25
3
3
PF-SW
COM(+24V)
26
26
4
4
OL-SW
5
5
PSW1
6
6
PSW2
7
7
PSW
CUTSW
1
8
8
OL-LED
CUTSW
2
9
9
PO-LED
M(–)
3
10
10
HU-LED
M(+)
4
11
11
ER-LED
12
Vcc(+5V)
12
M
ø3
THERMAL HEAD
CUTTER UNIT
CN5
M
MAGNET
CORE
(1 TURN)
POWER SUPPLY UNIT
CN3
[CN8] is not connected yet.
– 58 –
CN2
CN1
VP(+24V)
1
1
L
1
VP(+24V)
2
2
NC
2
NC
3
3
N
3
P-GND
4
4
NC
4
P-GND
5
FG
5
MAGNET
CORE
(1 TURN)
ø4
5
8
C
– 59 –
VCC
C9
33P
93C46
GND
VCC
IC8
C134
0.1U
R25
10K
VH
DQ7
FN1A4P
VCC
ZD2
RD4. 7JSB1
C127
100P
C126
33P
R18
33
CS
SK
DI
DO
1
2
3
4
Q4
A1649
R120
10K
DQ6
FA1A4P
10K
R19
C8
33P
VCC
63
61
62
59
57
56
55
52
54
16
51
60
9
10
11
13
14
15
41
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
32
31
30
29
28
27
26
25
VP
Q5
A1388
R119
10K
IC10
UPD65622GF-TSP
PSOE
PSCE0
PSCE1
RFSH
RD
WR
CE
RESET
CLK
INTCDT
INTSDT
RAMCS
CSTB
ACK
BUSY
ERROR
SELECT
POUT
HDON
CD0
CD1
CD2
CD3
CD4
CD5
CD6
CD7
IN9
IN10
IN11
IN12
IN13
IN14
IN15
IN16
I/O1
I/O2
I/O3
I/O4
IN5
IN6
IN7
IN8
58
12
33
53
71
80
34
72
79
78
77
76
75
74
73
70
69
68
67
66
65
64
38
37
36
35
39
40
49
50
46
48
42
43
44
45
47
5P8128 :
5P832 :
PSSEL
GND
GND
GND
GND
TEST
VCC
VCC
D0
D1
D2
D3
D4
D5
D6
D7
A0
A1
A2
A3
A15
A17
OUT1
OUT2
OUT3
OUT4
CUTSW
CUTON
SDATA
SCLK
HISTIN
LATCH
STB4
STB3
STB2
STB1
HDPWR
DQ5
FA1A4P
EXPANDED I/O BLOCK
R124
10K
R17
10K
1
C135
0.1U
JPA2
JPB2
2
FL4
TU02M
33 × 4
Standard
JPB2=Cut, JPA2=Short
D8
D9
D10
D11
D12
D13
D14
D15
A0
A1
A2
A3
A15
A17
R21
R20
R23
R22
VCC
C128
VCC
3
C129
C131
C130
33P × 4
R127
1K
R128
20K
R131
4.7K
VCC
C120
VH
DQ3
FA1A4P
VCC
C121
100P × 3
RA1
10K × 4
R130
4.7K
C123
2 4 35
1
VCC
R129
4.7K
R134
4.7K
DQ4
FN1A4P
2
4
6
8
10
12
14
16
18
20
22
24
26
COM
GND
GND
SO
GND
GND
VDD
/STB4
/STB2
TH2
GND
COM
COM
VP
Q3
B1359
Q1
D2010
CN7
53014-1210
12
VCC
11
ER-LED
10
HU-LED
9
PO-LED
8
OL-LED
7
PSW
6
PSW2
5
PSW1
4
OL-SW
3
PF-SW
2
COPEN
1
GND
R16
1K
1/2W
(AOI : J080-85523)
5332-265G1
1
3
5
7
9
11
13
15
17
19
21
23
25
CN6
THERMAL HEAD BLOCK
COM
COM
GND
SI
CLK
/LAT
/STB5
/STB3
/STB1
TH1
GND
GND
COM
C122
100P
CN5
5483-04A-RED
4
3
2
1
VCC
VH
4.
Main Logic Board
4-1. Circuit Diagram
A
SIDE B
– 60 –
VB
D8
D9
D10
D11
D12
D13
D14
D15
D8
D9
D10
D11
D12
D13
D14
D15
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
28
20
22
27
11
12
13
15
16
17
18
19
16
22
24
29
1
13
14
15
17
18
19
20
21
11
30
20
2
19
18
17
16
15
14
13
12
10
9
8
7
6
5
4
3
VPP
VCC
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
CE2
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
IC1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
(HM62256ALFP)
HM6264LFP
VCC
CE
OE
WE
D0
D1
D2
D3
D4
D5
D6
D7
LH5P8128N
(LH5P832N)
CE1
OE
R/W
RFSH
D0
D1
D2
D3
D4
D5
D6
D7
IC6
(AM27C4096)
AM27C2048
(AM27C1024)
GND
GND
OE
CE
O0
O1
O2
O3
O4
O5
O6
O7
O8
O9
O10
O11
O12
O13
O14
O15
IC11
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
12
11
10
9
8
7
6
5
27
26
23
25
4
28
3
31
2
32
30
1
40
21
22
23
24
25
26
27
28
29
31
32
33
34
35
36
37
38
39
A13
C137
0.1U
VCC
1
1
2
3
2
FL1
TU02M
FL5
TU02M
6264: Standard
62256: JPA1=Cut, JPB1=Short
JPA1
JPB1
A14
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
C110
0.1U
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
MEMORY BLOCK
3
VCC
VCC
C4
33P
D0
D1
D2
D3
D4
D5
D6
D7
VCC
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
16
22
24
29
1
13
14
15
17
18
19
20
21
32
12
31
13
11
14
16
18
20
23
25
27
29
15
17
19
21
24
26
28
30
VCC
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
CE2
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
LH5P8128N
(LH5P832N)
CE1
OE
R/W
RFSH
D0
D1
D2
D3
D4
D5
D6
D7
IC7
(UPD23C16000)
(UPD23C8000)
UPD23C4000A
W/B
GND
GND
OE
CE
O0
O1
O2
O3
O4
O5
O6
O7
O8
O9
O10
O11
O12
O13
O14
O15/A-1
IC9
12
11
10
9
8
7
6
5
27
26
23
25
4
28
3
31
2
32
30
22
10
9
8
7
6
5
4
3
41
40
39
38
37
36
35
34
33
2
1
42
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
VCC
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
C111
0.1U
1
2
FL2
TU02M
3
VCC
4.7K
R28
VCC
VEXT
R29
1K
VCC
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
COMMUNICATION I/F BLOCK
CN9
PHEC40R-R111
VEXT
VCC
SIDE A
B
D
C
– 61 –
C105
33P × 9
3
1
R9
R6
R10
R8
R7
R5
R4
R12
R13
R14
R123
33 × 9
VCC
10K × 2
C103 C101
C107 C119
C104
C102
C106
C108
VCC
2
X1
CST9.83MT
3
FL3
TU02M
C11
0.1U
C118
0.1U
R122
3.3K
2
1
C125
0.1U
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
VCC
27
28
29
30
31
32
33
34
36
37
38
39
40
41
42
43
10
26
35
53
99
94
73
1
44
84
76
85
80
79
78
77
72
70
69
68
67
66
100
101
102
103
104
81
82
83
71
74
75
20
21
22
23
24
25
HD6413003F10T
P40/D0
P41/D1
P42/D2
P43/D3
P44/D4
P45/D5
P46/D6
P47/D7
D8
D9
D10
D11
D12
D13
D14
D15
VSS
VSS
VSS
VSS
VSS
AVSS
VSS
VCC
VCC
AVCC
VCC
VREF
LWR
HWR
RD
AS
NMI
STBY
CLK
P62/BACK
P61/BREQ
P60/WAIT
P80/RFSH/IRQ0
P81/CS3/IRQ1
P82/CS2/IRQ2
P83/CS1/IRQ3
P84/CS0
MD0
MD1
MD2
RES
EXTAL
XTAL
P90/TXD0
P91/TXD1
P92/RXD0
P93/RXD1
P94/SCK0/IREQ4
P95/SCK1/IREQ5
IC5
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
P54/A20
P55/A21
P56/A22
P57/A23
PC0
PC1
PC2/TEND2/CS4
PC3/DREQ2/CS5
PC4/TEND3/CS6
PC5/DREQ3/CS7
PC6/IRQ6
PC7/IRQ7
P70/AN0
P71/AN1
P72/AN2
P73/AN3
P74/AN4
P75/AN5
P76/AN6
P77/AN7
PB0/TP8/TIOCA3
PB1/TP9/TIOCB3
PB2/TP10/TIOCA4
PB3/TP11/TIOCB4
PB4/TP12/TIOCXA
PB5/TP13/TIOCXB
PB6/TP14/DREQ0
PB7/TP15/DREQ1/
PA7/TP7/TIOCB2
PA6/TP6/TIOCA2
PA5/TP5/TIOCB1
PA4/TP4/TIOCA1
PA3/TP3/TIOCB0/
PA2/TP2/TIOCA0/
PA1/TP1/TEND1/T
PA0/TP0/TEND0/T
RESO
3.3K × 4
45
46
47
48
49
50
51
52
54
55
56
57
58
59
60
61
62
63
64
65
95
96
97
98
11
12
13
14
15
16
17
18
86
87
88
89
90
91
92
93
2
3
4
5
6
7
8
9
112
111
110
109
108
107
106
105
19
R3
R2
R104
R105
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
@
DA0
DA1
DA2
DA3
DA4
2
4
6
8
VCC
DQ2
FA1A4P
FEED MOTOR BLOCK
D1
EG01YV0
R15
10K
1
0
1
3
5
7
9
R117
10K
R103
10K
TA1
MP4020
1C
1B
2C
2B
3C
3B
4C
4B
E
E
VP
R118
33
UPC339C
2
1
–
2
+
–
3
C117
33P
4
5
1
–
+
IC12-B
R30
4.7K
10K
VCC
R107
R109
20K
DA1
10K
C13
0.1U
R108
7
UPC339C
6
R110
20K
C114
0.1U
10K
2
R33
2.7K
1
3
R111
VR4
4.7K
R137
1K
DA3
+
–
VO
13
IC12-D
–
+
11
UPC339C
10
C14
0.1U
Q8
D2010
Q9
D2010
C113
0.1U
VCC
C15
0.1U
VCC
2
R31
2.7K
R27
10K
D4
1SR139-100
1
3
PERIPHERAL/BUZZER BLOCK
R114
20K
DCB010
DD1
BZ
DA4
R26
4.7K
10K
R115
+
BZ1
QMB111P
R132
1K
DQ8
FN1A4P
R133
1K
DQ9
FN1A4P
G
N
D
VCC
R113
20K
9
8
VCC
VCC
VI
IC3
UPC7824HF
R1
330
IC12-C
UPC339C
14
R32
4.7K
VCC
R112
20K
R116
4.7K
VCC
SENSERS BLOCK
VP
DA2
DQ1
FA1A4P
CN2
5483-02A
2
HEAD UP
1
DETECTOR
20K
VCC
DA0
10K
R100
CN4
5483-06A
1
2
3
FEED
4
MOTOR
5
6
R106
VCC
IC12-A
R11
1K
VCC
Q2
B1359
D2
1SR139-100
VR3
4.7K
R136
1K
VCC
R101
220
MARK
PE
LABEL
VCC
VP
VCC
D3
1SR139-100
3
1
3
1
VR1
47K
VR2
4.7K
VCC
CN1
53014-0710
7
6
5
4
3
2
1
R135
220
2
2
<FOR PRESENTER>
1
2
3
4
5
[CN8]
53014-0510
VEXT
A
SIDE D
SIDE C
– 62 –
C136
(IC10)
5273-04A
CN3
C138
(IC11)
1
2
3
4
C116
(IC6)
C132
(IC9)
+
C1
1000U
35V
C112
(IC7)
1
2
3
2
RC
VI
3
C124
(IC5)
4
G
N
D
1
0
9
VR
VO
8
6
C115
(IC4)
A
1
A
0
5
3
2
IC2
HLD051R2M
D
1
D
0
4
A
2
4
D
2
8
D
4
6
A
4
7
A
5
7
D
5
8
A
6
6
D
6
2
3
D
9
3
A
1
9
4
D
1
0
4
A
1
8
3
1
POWER BLOCK
2
D
8
BUS BLOCK
ZD1
RD7.5EB1
1
9
A
7
1
5
D
7
VCC
0.1U × 8
C6
1000U
35V
C10
(IC12)
+
CA5
220P × 8
5
A
3
CA4
220P × 8
9
D
3
8
D
1
2
6
A
1
4
7
D
1
3
7
A
1
2
VCC
VCC
8
A
1
0
R126
10K
R125
10K
1
5
D
1
5
1
9
A
8
R24
1K
CD
RESET
6
D
1
4
DCB010
DD3
M51953BL
GND
IC4
VCC
CA1
220P × 8
5
A
1
6
CA3
220P × 8
9
D
1
1
3
A
2
0
6
A
1
5
CA2
220P × 8
5
A
1
7
R121
1K
+ C7
0.047
5.5V
C2
0.47U
50V
4
DD2
DCB010
Q7
C3875
Q6
A1338
4
5
2
7
A
1
3
1
9
A
9
+ C109
0.1U
8
A
1
1
VB
VCC
VP
C5
33P
C133
33P
R102
10K
VB
C100
33P
C3
33P
C12
33P
B
D
4-2. Parts List
Main Logic Board
DRWG.NO.
C1
C2
C3-5
C6
C7
C8-9
C10-11
C12
C13-15
C100-108
C109-116
C117
C118
C119
C120-123
C124-125
C126
C127
C128-131
C132
C133
C134-138
CA1-5
R1
R2-3
R4-5
R6
R7-8
R9
R10
R11
R12-14
R15
R16
R17
R18
R19
R20-23
R24
R25
R26
R27
R28
R29
R30
R31
R32
R33
R100
R101
R102-103
R104-105
R106
R107-108
R109-110
R111
REV. PARTS NO.
05041081
05054745
05753304
05041081
05994732
05753304
05751045
05753304
05751045
05753304
05751045
05753304
05751045
05753304
05751015
05751045
05753304
05751015
05753304
05751045
05753304
05751045
05652212
06753314
06753324
06753304
06751031
06753304
06751031
06753304
06751021
06753304
06751031
06021024
06751031
06753304
06751031
06753304
06751021
06751031
06754721
06751031
06754721
06751021
06754721
06752725
06754721
06752725
06751031
06752215
06751031
06753324
06752031
06751031
06752031
06751031
PARTS NAME
Q'TY
CHEM. CAPA. 1000UF 35V
CHEM. CAPA. 0.47UF 50V
CERA. CAPA. CHIP
33PF 50V
CHEM. CAPA. 1000UF 35V
BACK-UP CAPA. FYD0H473Z
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 100PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 100PF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CERA. CAPA. CHIP
33PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CAPA. ARRAY 220PF 50V 8EL
CHIP RESISTOR 330 OHM 1/10W
CHIP RESISTOR 3.3 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
RD RESISTOR 1 K-OHM 1/2W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 2.7 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 2.7 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 220 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 3.3 K-OHM 1/10W
CHIP RESISTOR 20 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 20 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
1
1
3
1
1
2
2
1
3
9
8
1
1
1
4
2
1
1
4
1
1
5
5
1
2
2
1
2
1
1
1
3
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
1
– 63 –
REMARKS
RANK
Main Logic Board
DRWG.NO. REV. PARTS NO.
R112-114
R115
R116
R117
R118
R119-120
R121
R122
R123
R124-126
R127
R128
R129-131
R132-133
R134
R135
R136-137
RA1
VR1
VR2-4
Q1
Q2-3
Q4
Q5-6
Q7
Q8-9
DQ1-3
DQ4
DQ5-6
DQ7-9
TA1
D1
D2-4
DD1-3
ZD1
ZD2
IC1
IC2
IC3
IC4
IC5
IC6-7
IC8
IC9
IC10
IC11
IC12
CN1
CN2
CN3
CN4
CN5
CN6
CN7
06752031
06751031
06754721
06751031
06753304
06751031
06751021
06753324
06753304
06751031
06751021
06752031
06754721
06751021
06754721
06752215
06751021
06581039
06454732
06454721
07320101
07113591
07016491
07013381
07238754
07320101
07603016
07603017
07603016
07603017
07650054
08000048
08000044
08000047
08020090
08020095
08221043
08202020
08202011
08200109
08251006
08221042
08222047
09110115
09110076
08240076
08222091
09110020
08201022
09100370
09100270
09100614
09100267
09100532
09100177
09100444
PARTS NAME
Q'TY
CHIP RESISTOR 20 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 3.3 K-OHM 1/10W
CHIP RESISTOR 33 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 20 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 220 OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
RESIS. ARRAY 10 K-OHM 1/8W 4EL
RP RESISTOR RH0615C-47K
RP RESISTOR RH0615CS-4.7K
TRANSISTOR 2SD2010
TRANSISTOR 2SB1359
TRANSISTOR 2SA1649
CHIP TRANSISTOR 2SA1338-67*TA
CHIP TRANSISTOR 2SC3875S-G*AL
TRANSISTOR 2SD2010
DIGITAL TRANSISTOR FA1A4P
DIGITAL TRANSISTOR FN1A4P
DIGITAL TRANSISTOR FA1A4P
DIGITAL TRANSISTOR FN1A4P
TRANSISTOR ARRAY MP4020
DIODE EG01YV0
DIODE 1SR139-100AT
DIODE CHIP DCB010
ZENER DIODE RD7.5EB1T
ZENER DIODE RD4.7JSB1
SRAM
6264FP-100NS*EL
IC-REG HLD051R2M
IC-REG UPC7824
IC-RESET M51953BL
CPU
HD6413003F10T
PSRAM 5P8128N-80L*E1
EEPROM KM93C46
IC SOCKET DILB-8P-8J
IC SOCKET DILB-42P-8J
GATE ARRAY D65622GF-TSP
EPROM M5M27C202K-12
IC SOCKET DICF-40C-JAE
IC-LIN HA17339F*TL
CONNECTOR 53014-0710
CONNECTOR 5483-02A
CONNECTOR 5273-04A
CONNECTOR 5483-06A
CONNECTOR 5483-04AX-RED
CONNECTOR 5332-26SG1
CONNECTOR 53014-1210
3
1
1
1
1
2
1
1
1
3
1
1
3
2
1
1
2
1
1
3
1
2
1
2
1
2
3
1
2
3
1
1
3
3
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
– 64 –
REMARKS
RANK
S
S
S
S
S
S
S
S
S
S
S
TS4.**
Main Logic Board
DRWG.NO.
CN8
CN9
X1
FL1-5
BZ1
REV. PARTS NO.
09100516
09100610
09250037
09251119
45060201
PARTS NAME
CONNECTOR 53014-0510
CONNECTOR PHEC40R-R111
CERA. OSCILLATOR CST9.83MT
LINE FILTER TU02MT*R
BUZZER QMB-111P
– 65 –
Q'TY
1
1
1
5
1
REMARKS
RANK
F-GND
MOUNT-HOLE
GND
GND
TXD
RXD
CTS
DTR
RCH
MP-DTR
MP-TXD
RTS
FAULT
V+
V–
TR4
A1179
PSW
PEXT 1
PEXT 2
VEXT
VEXT
F-GND
MOUNT-HOLE
52065-6645
CN2
– 66 –
TR2
C3875
DBLD-J255AF-21L91
CN3
6
2
5
3
4
1
0
R5
33K
L9
1
0
L1
R2
3.3K
L4
L8
L5
7
13
B-01R × 9
2
3
5
20
11
16
15
4
14
VCC
R3
1K
L2
L6
L7
L3
R4
3.3K
R1
10K
TR3
FN1A4P
VCC
DCB010
×2
D1
D2
C6
1U
50V
C2
1U
50V
+
VR1
EVN-D2A-10K
TR5
FA1A4P
TR1
FA1A4P
C4
0.1U
JP6
V+
+
+
VCC
1
3
VCC
16
3
2
14
13
8
7
1
C3
220U
6.3V
2
VCC
GND
C2–
V–
D1I
R1O
R2O
D2I
C2+
HD151232FP
VCC
C1–
V+
D1O
R1I
R2I
D2O
C1+
IC1
JP4
JP3
JP2
JP1
15
5
6
11
12
9
10
4
+
C5
1U
50V
C1
1U
50V
/DIEN
GND
RXD
ID0
ID2
GND
PEXT 1
VEXT
VVR
DIN1
DIN3
DIN5
DIN7
GND
VCC
+
V–
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
PHEC40P-R111
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
CN1
JP5
/FAULT
DTR
GND
TXD
CTS
ID1
GND
PSWIN
PEXT 2
VEXT
GND
DIN2
DIN4
DIN6
DIN8
GND
VCC
1 1 1 1 1 1 1
9 0 1 2 3 4 5 6
1
8 7 6 5 4 3 2 1
DSW1
VCC
5.
RS232C Interface Board
5-1. Circuit Diagram
5-2. Parts List
RS232C Interface Board
DRWG.NO.
C1-2
C3
C4
C5-6
R1
R2
R3
R4
R5
VR1
TR1
TR2
TR3
TR4
TR5
D1-2
IC1
DSW1
CN1
CN2
CN3
L1-9
REV. PARTS NO.
*2
#2
05051057
05002213
05751045
05051057
06751031
06753324
06751021
06753324
06753334
06451033
07603016
07238754
07603017
07011793
07603016
08000047
08200155
09090034
09090046
09100611
09100421
09100483
09990705
PARTS NAME
Q'TY
CHEM. CAPA.
1UF 50V
CHEM. CAPA. 220UF 6.3V
CERA. CAPA. CHIP 0.1UF 50V
CHEM. CAPA.
1UF 50V
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 3.3 K-OHM 1/10W
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 3.3 K-OHM 1/10W
CHIP RESISTOR 33 K-OHM 1/10W
RP RESISTOR EVN-D2A-10K
DIGITAL TRANSISTOR FA1A4P
CHIP TRANSISTOR 2SC3875S-G*AL
DIGITAL TRANSISTOR FN1A4P
CHIP TRANSISTOR 2SA1179M6-STR
DIGITAL TRANSISTOR FA1A4P
DIODE CHIP DCB010
IC-I/F HD151232FP*TL
DIP SWITCH KSS08-1
DIP SWITCH EAH108L-BLK
CONNECTOR PHEC40P-R111
CONNECTOR 52065-6645
CONNECTOR DBLD-J25SAF-21L9-1
BEADS INDUCTOR B01-RT
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
9
– 67 –
REMARKS
RANK
– 68 –
F-GND
MOUNT-HOLE
GND
GND
SD (+)
SD (–)
RD (+)
RD (–)
CS (+)
CS (–)
RS (+)
RS (–)
FAULT
PSW
PEXT 1
PEXT 2
VEXT
VEXT
F-GND
MOUNT-HOLE
52065-6645
CN2
DBLD-J255AF-21L9
CN3
L7
7
13
6
2
5
3
4
1
0
1
0
L10
TR1
FA1A4P
L5
L9
L8
L3
9
10
17
18
19
23
24
25
14
B-01R × 10
VCC
L6
L2
L1
L4
R3
10K
VCC
100 × 2
R4
10K
R2
R1
C1
0.1U
VCC
JP1
1
3
VCC
14
13
6
7
2
1
10
11
8
16
2
VR1
EVN-D2A-10K
9
12
+
3
15
4
5
VCC
D2I
D2EN
R2O
D1I
D1EN
R1O
MC34051M
D1O+
D1O–
R2I+
R2I–
R1I+
R1I–
D2O+
D2O–
GND
VCC
IC1
C2
220U
6.3V
VCC
DSW2
/DIEN
GND
RD
ID0
ID2
GND
PEXT 1
VEXT
DIN9
DIN11
VVR
DIN1
DIN3
DIN5
DIN7
GND
VCC
DOEN
5 6 7 8
1
4 3 2 1
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
PHEC40P-R111
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
CN1
FAULT
RS
GND
SD
CS
ID1
GND
PSWIN
PEXT 2
VEXT
DIN10
DIN12
GND
DIN2
DIN4
DIN6
DIN8
GND
VCC
1 1 1 1 1 1 1
9 0 1 2 3 4 5 6
1
8 7 6 5 4 3 2 1
DSW1
VCC
6.
RS422A Interface Board
6-1. Circuit Diagram
6-2. Parts List
RS422A Interface Board
DRWG.NO.
C1
C2
R1-2
R3-4
VR1
TR1
IC1
DSW1
DSW2
CN1
CN2
CN3
L1-10
REV. PARTS NO.
*2
#2
*2
#2
05751045
05002213
06751014
06751031
06451033
07603016
08200127
09090034
09090046
09090033
09090045
09100611
09100421
09100483
09990705
PARTS NAME
CERA. CAPA. CHIP 0.1UF 50V
CHEM. CAPA. 220UF 6.3V
CHIP RESISTOR 100 OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
RP RESISTOR EVN-D2A-10K
DIGITAL TRANSISTOR FA1A4P
IC-I/F MC34051M
DIP SWITCH KSS08-1
DIP SWITCH EAH108L-BLK
DIP SWITCH KSS04-1
DIP SWITCH EAH104L-BLK
CONNECTOR PHEC40P-R111
CONNECTOR 52065-6645
CONNECTOR DBLD-J25SAF-21L9-1
BEADS INDUCTOR B01-RT
– 69 –
Q'TY
1
1
2
2
1
1
1
1
1
1
1
1
1
1
10
REMARKS
RANK
– 70 –
F-GND
MOUNT-HOLE
GND
EXT-GND
RETURN-GND
VCC
CPL
SLCT-IN
PE
SLCT
ERROR
ACK
BUSY
STROBE
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
INIT
52065-6645
PSW
PEXT 1
PEXT 2
VEXT
VEXT
F-GND
MOUNT-HOLE
57RE-40360-BD29
CN2
CN3
6
2
5
3
4
1
0
17
0
16
33
19
18
34
36
12
13
32
10
11
1
2
3
4
5
6
7
8
9
31
RA1
4.7K × 8
–30
L1
B-01R
C1
0.1U
VCC
2 3 4 5 6 7 8 9
1
VCC
RA2
1.8K × 6
VCC
C4
0.1U
(IC1)
2 3 4 5 6 7
1
VCC
10
12
6
2
E
F
C
8
5
IC1
LS05
A
1
TR1
FA1A4P
2
3
9
R11
100
R2
R3
R4
R5
R6
R7
R8
R9
VR1
EVN-D2A-10K
VCC
B
D
VCC
IC1
LS05
11
4
13
R10
10K
R1
1K
4.7K × 8
1
3
VCC
C3
1000P
VCC
ID0
ID2
GND
PEXT 1
VEXT
VVR
DIN1
DIN3
DIN5
DIN7
GND
VCC
ERROR
/SLCT
/BUSY
STB
GND
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
+
VCC
C2
220U
6.3V
PHEC40P-R111
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
CN1
ID1
GND
PSWIN
PEXT 2
VEXT
GND
DIN2
DIN4
DIN6
DIN8
GND
VCC
/INIT
/PE
ACK
GND
VCC
7.
Centronics Interface Board
7-1. Circuit Diagram
7-2. Parts List
Centronics Interface Board
DRWG.NO.
C1
C2
C3
C4
R1
R2-9
R10
R11
RA1
RA2
VR1
TR1
IC1
CN1
CN2
CN3
L1
REV. PARTS NO.
05751045
05002213
05751025
05751045
06751021
06754721
06751031
06751014
06584729
06581824
06451033
07603016
08210142
09100611
09100421
09100482
09990705
PARTS NAME
Q'TY
CERA. CAPA. CHIP 0.1UF 50V
CHEM. CAPA. 220UF 6.3V
CERA. CAPA. CHIP 1000PF 50V
CERA. CAPA. CHIP 0.1UF 50V
CHIP RESISTOR 1 K-OHM 1/10W
CHIP RESISTOR 4.7 K-OHM 1/10W
CHIP RESISTOR 10 K-OHM 1/10W
CHIP RESISTOR 100 OHM 1/10W
RESIS. ARRAY 4.7K-OHM 1/8W 8EL
RESIS. ARRAY 1.8K-OHM 1/8W 6EL
RP RESISTOR EVN-D2A-10K
DIGITAL TRANSISTOR FA1A4P
TTL IC 74LS05FP*TL
CONNECTOR PHEC40P-R111
CONNECTOR 52065-6645
CONNECTOR 57RE40360-730BD29
BEADS INDUCTOR B01-RT
1
1
1
1
1
8
1
1
1
1
1
1
1
1
1
1
1
– 71 –
REMARKS
RANK
8.
Control Panel Board
8-1. Circuit Diagram
CN1
53014-1210
SW-CO
2
SW2
SW-FEED
3
SW1
SW-ONL
GND
4
1
R1
270
LED1
LT-1E21A
R5
270
LED5
LT-1E21A
R3
270
LED3
LT-1D11A
R2
270
LED2
LT-1D11A
R4
270
LED4
LT-1D11A
6
JP2
D2
1S1588
5
JP1
D1
1S1588
LED-POW
LED-ONL
LED-PAR
LED-HUP
LED-ERR
+5V
PSW
PSW-2
PSW-1
8
9
10
11
12
7
– 72 –
8-2. Parts List
Control Panel Board
DRWG.NO.
R1-5
D1-2
LED1
LED2-4
LED5
SW1-2
CN1
CN2
-
REV. PARTS NO.
*1
#1
06052714
08000039
08300058
08300081
08300058
09010043
09010041
09100444
PARTS NAME
RD RESISTOR 270 OHM 1/6W
DIODE 1S1588
LED LT-1E21A
LED LT-1D11A
LED LT-1E21A
PUSH SWITCH SKHHAL=S
PUSH SWITCH SKHHAL
CONNECTOR 53014-1210
Q'TY
REMARKS
5
2
1
3
1
2
2
1
NOT MOUNTED
09090047 LEAF SWITCH MSW-1705C
80700580 WIRE 26UL1571ORG050
– 73 –
1
2
RANK
9.
Paper-Out Detector Board
9-1. Circuit Diagram
CN1
4
3
2
1
VCC
MARK
PE
GND
PS1
PS60002
(MARK)
(51015-0400)
PS2
PS60002
(PE)
R1
220
R2
220
9-2. Parts List
Paper-Out Detector
DRWG.NO. REV. PARTS NO.
R1-2
PS1-2
-
PARTS NAME
06052211 RD RESISTOR 220 OHM 1/6W
08300082 PHOTO-INTERRUPTER PS6002A-KS
30721010 CABLE UNIT
TMP4
Q'TY
REMARKS
RANK
2
2
1
10. Label Sensor Board
10-1.Circuit Diagram
CN1
LED
GND
LABEL
3
2
1
53014-0310
PS1
TLP833
(LABEL)
10-2.Parts List
Transmissive Sensor
DRWG.NO. REV. PARTS NO.
PS1
CN1
PARTS NAME
08300150 PHOTO-INTERRUPTER TLP833
09100460 CONNECTOR 53014-0310
– 74 –
Q'TY
1
1
REMARKS
RANK
P1994.12
P1995.06
HEAD OFFICE
STAR MICRONICS CO., LTD.
OVERSEAS SUBSIDIARY COMPANIES
STAR MICRONICS AMERICA, INC.
536 Nanatsushinnya, Shimizu,
Shizuoka, 424, Japan
70-D Ethel Road West,
Piscataway, NJ 08854, U.S.A.
Tel: (908)572-9512
Telefax: (908)572-5095
Tel: 0543-47-0112
Fax: 0543-48-5271
STAR MICRONICS DEUTSCHLAND GMBH
STAR MICRONICS U.K. LTD.
Westerbachstraße 59,
D-60489 Frankfurt, Germany
Telefon: 069 78 99 90
Telefax: 069 78 10 06
Telex: 4 175825 star d
Star House, Peregrine Business
Park, Gomm Road, High Wycombe
Bucks, HP13 7DL U.K.
Tel: 01494-471111
Fax: 01494 473333
Telex: 83393 STAR UK
Distributed by
Printed in Japan, 80822421-B