Download Sony SPK-HCG Preparation Guide
Transcript
4-274-833-01(1) 4 A O M37 Sports Pack Preparation Guide Guide de préparation du caisson sport 스포츠팩 준비 가이드 B P 5 6 55 HDR-PJ20/PJ10, HDR-CX550V/CX550/CX520V/CX520/ CX505V/CX500V/CX500/CX12/CX11/CX7/ CX6, HDR-XR550V/XR550/XR520V/XR520/ XR500V/XR500/XR160, HDR-SR12/SR11/SR8/SR7/SR5, HDR-HC9/HC7/HC5 DCR-SX60/SX50/SX41/SX40/SX31/SX30 ˎ POWER ON/OFF HDR-HC9/HC7/HC5 O SPK-HCG 3 D © 2011 Sony Corporation Printed in Japan 1 Open the sports pack. 2 Disconnect the Audio/Remote plug b from the camera mounting shoe. 3 Remove the camera mounting shoe attached to this unit. 2 3 Keep pressing the knob on one side of the camera mounting shoe in the direction of the arrow to release the lock, and slide the camera mounting shoe off slowly. Camera mounting shoe F-2 is attached to this unit when this unit is shipped from the factory. O Selecting the Camera Mounting Shoe Slide the unlock button in the direction of the arrow and hold it, then slide the open slider and release the buckle. Open the rear body. ON 2 O Preparing the Sports pack 4 Attach the shoulder strap. 1 Q C The models of Sony digital HD video camera recorders and digital video camera recorders (referred to below as “camera”) described below may not be available in all countries/ regions. Adjust the length of the grip strap while holding this unit so that your fingertips can easily reach the START/STOP button, Telephoto button, Wide button and PHOTO button. OFF ON/OFF ˎ Notes 1 Open the rear body and remove the spacer a . 2 Close the rear body and then fasten the buckles. 3 Adjust the grip belt. OFF Preparing O 4 Choose the camera mounting shoe and the number according to the table below. / A/V A/V OUT A/V HDR-UX20/UX19/UX10/UX9 DCR-DVD910/DVD510 DCR-SR87/SR77/ SR67/SR57/SR48/SR47/SR38/SR37 DCR-SX60/SX50/SX41/SX40/SX31/ SX30 ˎ DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 / -4-I Camera mounting shoe D 1 F-2 -4- e E Camera mounting shoe Sabot de montage de caméra a / A/V Body Corps 3 4 Guide Guide A/V A/V OUT 3 F / ON/OFF -4-A 4 HD 1 2 3 a 1 2 3 H b 2 I 1 F-2 2 3 G 1 H D 1 F-2 1 I-2 2 J H G J 1 K 1 1 L I-2 5 c F-2 K 1 MC 2 F-2 3 HDR-HC9/HC7/HC5, DCR-DVD708/DVD608/DVD308/DVD306/ DVD109/DVD108/DVD106 DCR-HC62/HC54/HC53/HC52/HC51/HC48/ HC47/HC45/HC38/HC37 HDR-CX12/CX11/CX7/CX6 HDR-PJ50V/PJ50/PJ40V/PJ30V/PJ30/PJ20/PJ10, HDR-XR160, HDR-SR8/SR7/SR5 HDR-CX700V/CX700/CX690/CX560V/CX560 HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD850/DVD810/DVD710/ DVD650/DVD610/DVD510/DVD450/DVD410/ DVD310/DVD150/DVD115/DVD110 HDR-CX360V/CX360, HDR-XR520V/XR520/XR500V/XR500/XR200V/ XR200/XR106/XR105/XR101/XR100, HDR-SR12/SR11/SR10, DCR-SR220/SR210 HDR-CX520V/CX520/CX505V/CX500V/CX500, DCR-SR88/SR85/SR78/SR75/SR68/SR65/SR58/ SR55/SR46/SR45/SR36/SR35 HDR-XR350V/XR350 HDR-CX120/CX106/CX105/CX100, DCR-SX60/SX50/SX41/SX40/SX31/SX30 DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/ SR37 HDR-CX550V/CX550, HDR-XR550V/XR550 HDR-XR155/XR150 1 D 4 HDR-CX12/CX11/CX7/CX6 b F-2 4 F-2 3 K L 5 L -4-F Reflex prevention ring -4-H Reflex prevention ring (M30 × ø 47) DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 -4-I -3 Reflex prevention ring (M30 × ø 50) Reflex prevention ring (M30 × ø 58) Reflex prevention ring (M30 × ø 62) ˎ Reflex prevention ring (M37 × ø 49) HDR-CX520V/CX520/CX505V/CX500V/CX500 DCR-SR85/SR75/SR65/ -4-J SR55/SR46/SR45/SR36/SR35 -4-K DCR-SX60/SX50/SX41/SX40/SX31/SX30 -3 DCR-DVD850/DVD810/DVD710/DVD650/DVD610/DVD450/DVD410/ -4-L DVD310/DVD150/DVD115/DVD110 ND 2 3 4 DCR-SR88/SR78/SR68/SR58 M 3 M30 43 d N 30 47 (M30 50) (M30 58) M30 62 M37 49 HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD708/DVD608/DVD510/ DVD308/DVD306/DVD109/DVD108/ DVD106, DCR-HC62/HC54/HC53/HC52/HC51/ HC48/HC47/HC45/HC38/HC37 HDR-CX360V/CX360/CX120/CX106/ CX105/CX100, HDR-XR155/XR150, DCR-SR87/SR77/SR67/SR57/SR48/SR47/ SR38/SR37 DCR-DVD850/DVD810/DVD710/DVD650/ DVD610/DVD450/DVD410/DVD310/ DVD150/DVD115/DVD110, DCR-SR88/SR78/SR68/SR58 HDR-XR350V/XR350, DCR-SR85/SR75/SR65/SR55/SR46/SR45/ SR36/SR35 HDR-PJ50V/PJ50/PJ40V/PJ30V/PJ30, HDR-XR200V/XR200/XR106/XR105/XR101/ XR100, HDR-SR10, DCR-SR220/SR210 HDR-CX700V/CX700/CX690/CX560V/ CX560 ( -4-O) ˎ ˎ HDR-CX700V/CX700/CX690/CX560V/CX560 -4-P) HDR-PJ40V/PJ30V/PJ30/PJ20/PJ10 HDR-CX360V/CX360 -4-Q 5 ˎ ˎ 5 Turn the LCD panel around so that it faces outwards and place it back in the camera. 6 Set functions such as focusing and lightning, to AUTO. Installing the Video Camera ˎˎ After installing the camera into this unit, you can turn the power of the camera on and off by pressing the POWER button of this unit. ˎˎ When using the HDR-HC9/HC7/HC5, turn the POWER switch on. DCR-DVD708/DVD608/DVD308/DVD306/DVD109/DVD108/DVD106 -4-M -3- d Unable to attach the supplied reflex prevention ring HDR-PJ20/PJ10, HDR-CX550V/CX550/CX520V/CX520/CX505V/CX500V/ CX500/CX12/CX11/CX7/CX6, HDR-XR550V/XR550/XR520V/XR520/XR500V/XR500/ XR160, HDR-SR12/SR11/SR8/SR7/SR5, HDR-HC9/HC7/HC5 DCR-SX60/SX50/SX41/SX40/SX31/SX30 Notes ˎ ˎ HDR-CX550V/CX550/XR550V/XR550 DCR-HC62/HC54/HC53/HC52/ -4-N HC51/HC48/HC47/HC45/HC38/HC37 c Reflex prevention ring (M37 × ø 55) Camera HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD708/DVD608/DVD510/DVD308/ DVD306/DVD109/DVD108/DVD106, DCR-HC62/HC54/HC53/HC52/HC51/HC48/HC47/ HC45/HC38/HC37 HDR-CX360V/CX360/CX120/CX106/CX105/CX100, HDR-XR155/XR150, DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 DCR-DVD850/DVD810/DVD710/DVD650/DVD610/ DVD450/DVD410/DVD310/DVD150/DVD115/DVD110, DCR-SR88/SR78/SR68/SR58 HDR-XR350V/XR350, DCR-SR85/SR75/SR65/SR55/SR46/SR45/SR36/SR35 HDR-PJ50V/PJ50/PJ40V/PJ30V/PJ30, HDR-XR200V/XR200/XR106/XR105/XR101/XR100, HDR-SR10, DCR-SR220/SR210 HDR-CX700V/CX700/CX690/CX560V/CX560 When using a camera with a POWER switch, turn the POWER switch off. Also leave the power of this unit turned off. When using a camera with an internal power switch linked to the switching action of the LCD screen, you do not need to turn off the camera. SD Unlock the write-protect tab on the memory card and the cassette tape to enable them to record images. Make sure that the tape, memory card, disc, hard disk and internal memory have enough space to record images. Make sure that the disc is not finalized. Reflex prevention ring (M30 × ø 43) HDR-HC9/HC7/HC5 3 Notes The reflex prevention ring prevents external light from being reflected inside the sports pack (referred to below as “this unit”) and entering the lens. When using a camera model with no reflex prevention ring, external light from behind reflects against this unit. Keep your back away from sunlight as much as possible. HDR-UX20/UX19/UX10/UX9 DCR-DVD910/DVD510 -4-G -3 3 For the kinds of memory card (“Memory Stick Duo” media, SD card) compatible with your camera, refer to the camera’s operating instructions. 4 Attach the reflex prevention ring (-3- d ) to the filter attachment screw of the camera. J Attach a fully recharged battery pack. 3 Insert the media. HDR-XR350V/XR350/XR155/XR150 HDR-CX120/CX106/CX105/CX100 -4-E F-2 4 2 2 Install the battery pack. 1 Remove the filter, conversion lens, lens cap, lens hood or the shoulder strap from the camera. When using a camera with a manual lens shutter, open the lens shutter. HDR-PJ50V/PJ50 HDR-XR160 HDR-SR8/SR7/SR5 -4-D 1 1 Detach the accessory. K For details, refer also to the operating instructions supplied with the camera. -4-C 4 1 Preparing the Video Camera HDR-SR12/SR11/SR10 DCR-SR220/SR210 PHOTO J The tripod screw plate is attached to camera mounting shoe F-2/number 3 when this unit is shipped from the factory. If you use camera mounting shoe F-2/number 3, this step is not required. START/STOP 1 5 When using a camera mounting shoe other than camera mounting shoe F-2/number 3, detach the tripod screw plate c from camera mounting shoe F-2/number 3. Then align the tripod screw plate with the correct number on the chosen camera mounting shoe, and press until it clicks into place. HDR-XR200V/XR200/XR106/XR105/XR101/XR100 -4-B 1 L 2, 3 H 2 HDR-XR520V/XR520/XR500V/XR500 1 1 I-2 G ˎ ˎ e 2 3 ˎ G HDR-HC9/HC7/HC5, DCR-DVD708/DVD608/DVD308/DVD306/ DVD109/DVD108/DVD106 DCR-HC62/HC54/HC53/HC52/HC51/HC48/HC47/ HC45/HC38/HC37 HDR-CX12/CX11/CX7/CX6 HDR-PJ50V/PJ50/PJ40V/PJ30V/PJ30/PJ20/PJ10, HDR-XR160, HDR-SR8/SR7/SR5 HDR-CX700V/CX700/CX690/CX560V/CX560 HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD850/DVD810/DVD710/DVD650/ DVD610/DVD510/DVD450/DVD410/DVD310/ DVD150/DVD115/DVD110 HDR-CX360V/CX360, HDR-XR520V/XR520/XR500V/XR500/XR200V/ XR200/XR106/XR105/XR101/XR100, HDR-SR12/SR11/SR10, DCR-SR220/SR210 HDR-CX520V/CX520/CX505V/CX500V/CX500, DCR-SR88/SR85/SR78/SR75/SR68/SR65/SR58/SR55/ SR46/SR45/SR36/SR35 HDR-XR350V/XR350 HDR-CX120/CX106/CX105/CX100, DCR-SX60/SX50/SX41/SX40/SX31/SX30 DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 HDR-CX550V/CX550, HDR-XR550V/XR550 HDR-XR155/XR150 1 2 1 Number Camera ( 1 Coat the front glass with anti-fogging lens solution. Apply 2 to 3 drops of the anti-fogging lens solution provided onto the inside surface of the front glass of this unit. To increase the anti-fogging effect, use the desiccant supplied. For details, refer to “Desiccant” in the supplied operating instructions. 2 Remove foreign materials such as dust, sand or hair from the O-ring, groove and any surface the camera touches, and then apply the grease evenly to the O-ring. If the body is closed with such materials present, those areas may be damaged and water may leak in. For details on handling the O-ring, refer to “Handling the O-ring” in the operating instructions. 3 Attach the camera mounting shoe. Align the screw position of the camera mounting shoe with the tripod screw on the bottom of the camera. When using one of the models below, open the jack cover and firmly insert the Audio/Remote plug into the A/V jack, A/V OUT jack or A/V remote jack: HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD510, DCR-SR87/SR77/SR67/ SR57/SR48/SR47/SR38/SR37, DCR-SX60/SX50/SX41/SX40/SX31/SX30 ˎˎ When using the DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37, insert the Audio/Remote plug with the jack cover sufficiently open. (See illustration -4-I ) If the jack cover is not sufficiently open, it may jam the Audio/Remote plug and cause a poor connection. Attach the camera mounting shoe to the camera using the metal parts of shoulder strap (-4- e ) as illustrated. 4 Connect the plug and install the camera. Depending on your camera, firmly insert the Audio/Remote plug into the A/V jack, A/V OUT jack or A/V remote jack. (except camera models in step 3) When installing the camera into this unit, align the camera mounting shoe with the guide inside the front body of this unit, and then push the rear of the camera mounting shoe until it clicks into place. Notes ˎˎ Be sure to keep this unit horizontal when installing the camera mounting shoe. Installing the camera mounting shoe in a vertical motion may damage the camera mounting shoe and the front body. ˎˎ Be sure not to cover the lens, LCD screen, view finder, zoom lever or PHOTO button with the cable. ˎˎ When using a camera with an internal power switch linked to the switching action of the LCD screen, connecting the Audio/Remote plug will switch the Still image recording mode/Video playing mode of the camera to Movie recording mode. When using HDR-XR520V/XR520/XR500V/XR500 (See illustration -4-A) Open the jack cover and connect the plug. (Arrange the cable connected to this unit in a loop towards the rear of the plug, as illustrated.) Install the camera into this unit, taking care not to catch the cable on the parts inside this unit. After installing the camera into this unit, arrange the cable on the grip belt side of the camera. When using HDR-XR200V/XR200/XR106/XR105/XR101/XR100 (See illustration -4-B) Open the jack cover and connect the plug. Arrange the cable connected to this unit in a loop towards the rear of the plug, as illustrated. Install the camera into this unit, taking care not to catch the cable on the parts inside this unit. After installing the camera into this unit, arrange the cable on the grip belt side of the camera. When using HDR-SR12/SR11/SR10, DCR-SR220/SR210 (See illustration -4-C) Open the jack cover and connect the plug. (Arrange the cable connected to this unit in a loop towards the rear of the plug, as illustrated.) After installing the camera into this unit, lightly press the cable to arrange it on the grip belt side of the camera. When using HDR-PJ50V/PJ50, HDR-XR160 or HDR-SR8/SR7/SR5 (See illustration -4-D) Open the jack cover. Connect the plug. After installing the camera into this unit, arrange the cable on the grip belt side of the camera. When using HDR-XR350V/XR350/XR155/XR150 or HDR-CX120/CX106/CX105/ CX100 (See illustration -4-E) Open the jack cover and connect the plug. After installing the camera into this unit, arrange the cable on the grip belt side of the camera, taking care not to catch the cable on the camera mounting shoe or other parts. When using HDR-CX12/CX11/CX7/CX6 (See illustration -4-F) Open the jack cover. Connect the plug. Put the cable on the camera mounting shoe and install the camera into this unit. After installing the camera into this unit, arrange the cable on the grip belt side of the camera, placing the cable so that it does not fall from the camera mounting shoe. When using HDR-UX20/UX19/UX10/UX9 or DCR-DVD910/DVD510 (See illustration -4-G) (If you completed the following and in step -3, start from .) Connect the plug. Attach the camera mounting shoe to the camera. After installing the camera into this unit, arrange the cable. (Hook the cable to the cable holder.) When using HDR-HC9/HC7/HC5 (See illustration -4-H) Open the jack cover. Connect the plug. After installing the camera into this unit, arrange the cable on the grip belt side of the camera. When using DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 (See illustration -4-I) (If you completed the following and in step -3, start from .) Attach the plug, opening the jack cover enough for it not to catch the base of the plug. Attach the camera mounting shoe to the camera. Install the camera into this unit, keeping the cable on the top side of the camera. Secure the cable in the clip of the camera mounting shoe, taking care not to catch the cable on the LCD screen. ˎˎ If the camera battery is too large for the cable to be passed behind it, pass the cable along the top of the battery and fasten the cable with clips. When using HDR-CX520V/CX520/CX505V/CX500V/CX500 or DCR-SR85/SR75/ SR65/SR55/SR46/SR45/SR36/SR35 (See illustration -4-J) Open the jack cover and connect the plug. (Arrange the cable connected to this unit in a loop towards the rear of the plug, as illustrated.) After installing the camera into this unit, lightly press the cable to arrange it on the grip belt side of the camera. When using DCR-SX60/SX50/SX41/SX40/SX31/SX30 (See illustration -4-K) (If you completed the following and in step -3, start from .) Lift the grip belt and open the jack cover to connect the plug. Attach the camera mounting shoe to the camera. Install the camera into this unit with the cable curled on the top side of the camera. After installing the camera into this unit, arrange the cable. (Hook the cable to the cable holder.) When using DCR-DVD850/DVD810/DVD710/DVD650/DVD610/DVD450/ DVD410/DVD310/DVD150/DVD115/DVD110 (See illustration -4-L) Open the jack cover. Connect the plug. Clip the cable into the groove of the reflex prevention ring on the grip belt side as illustrated. Arrange the cable as illustrated and attach the camera mounting shoe to this unit. Notes on attachment: ˎˎ Do not bend the cable. ˎˎ Make sure that the cable has not come off the groove of the reflex prevention ring. After installing the camera into this unit, make sure that the cable is not interfering with the lens of the camera. When using DCR-DVD708/DVD608/DVD308/DVD306/DVD109/DVD108/ DVD106 (See illustration -4-M) Open the jack cover. Connect the plug. After installing the camera into this unit, arrange the cable. When using the HDR-CX550V/CX550/XR550V/XR550 or DCR-HC62/HC54/ HC53/HC52/HC51/HC48/HC47/HC45/HC38/HC37 (See illustration -4-N) Open the jack cover. Connect the plug. After installing the camera into this unit, arrange the cable. (Hook the cable at the cable holder.) When using DCR-SR88/SR78/SR68/SR58 (See illustration -4-O) Open the jack cover. Connect the plug. Clip the cable into the groove of the reflex prevention ring as illustrated. Arrange the cable as illustrated and attach the camera mounting shoe to this unit. Notes on attachment: ˎˎ Do not bend the cable. ˎˎ Make sure that the cable has not come off the groove of the reflex prevention ring. After installing the camera into this unit, make sure that the cable is not interfering with the lens of the camera. When using HDR-CX700V/CX700/CX690/CX560V/CX560 (See illustration -4-P) Open the jack cover. Pass the cable under the grip belt of the camera and connect the plug. After installing the camera into this unit, arrange the cable on the grip belt side of the camera. When using HDR-PJ40V/PJ30V/PJ30/PJ20/PJ10 or HDR-CX360V/CX360 (See illustration -4-Q) Open the jack cover and connect the plug. After installing the camera into this unit, arrange the cable on the grip belt side of the camera. 5 Close the rear body. Press the rear body shut and fasten the buckles until they click in place. Notes ˎˎ Be careful not to pinch the cables when closing the rear body. ˎˎ Although the center of the lens of some camera models may be out of line with the center of the front glass of this unit when installed, this does not cause any problems when recording. 4# 㧶᳖ዢṦ#⫚ᆚ㩂ᇊ#㍞ἾᱦṦ#ⲏㄓ㩓ឲ៎1 Préparation Remarques Les modèles de caméscopes HD numériques et de caméscopes numériques Sony (appelés ci-dessous le « caméscope ») mentionnés ci-dessous peuvent ne pas être commercialisés dans tous les pays ou toutes les régions. Préparation du caisson sport 1 Ouvrez la partie arrière et retirez l’entretoise a . 2 Fermez la partie arrière et bloquez les fermoirs. 3 Réglez la sangle. Réglez la longueur de la sangle tout en tenant ce boîtier de manière à toucher facilement les touches START/STOP, Téléobjectif, Grand-angle et PHOTO du bout des doigts. 4 Fixez la bandoulière. Sélection du sabot de montage de caméscope 1 Ouvrez ce boîtier. Faites glisser le bouton de déverrouillage dans le sens de la flèche et maintenezle ainsi, puis faites glisser la glissière d’ouverture et relâchez le fermoir. Ouvrez la partie arrière. 2 Débranchez la fiche Audio/Commande à distance b du sabot de montage de caméscope. 3 Détachez le sabot de montage de caméscope fixé à cet appareil. Tout en maintenant le bouton sur le côté du sabot de montage de caméscope pressé dans le sens de la flèche pour libérer le verrou, sortez lentement le sabot de montage de caméscope en le faisant glisser. Le sabot de montage de caméscope F-2 a été fixé à ce boîtier en usine. 4 Choisissez le sabot de montage et le numéro en vous reportant au tableau suivant. Sabot de montage Numéro Caméscope de caméscope HDR-HC9/HC7/HC5, 1 DCR-DVD708/DVD608/DVD308/DVD306/ DVD109/DVD108/DVD106 D DCR-HC62/HC54/HC53/HC52/HC51/HC48/HC47/ 2 HC45/HC38/HC37 1 HDR-CX12/CX11/CX7/CX6 HDR-PJ50V/PJ50/PJ40V/PJ30V/PJ30/PJ20/PJ10, F-2 2 HDR-XR160, HDR-SR8/SR7/SR5 3 HDR-CX700V/CX700/CX690/CX560V/CX560 HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD850/DVD810/DVD710/DVD650/ G 1 DVD610/DVD510/DVD450/DVD410/DVD310/ DVD150/DVD115/DVD110 HDR-CX360V/CX360, HDR-XR520V/XR520/XR500V/XR500/XR200V/ H 1 XR200/XR106/XR105/XR101/XR100, HDR-SR12/SR11/SR10, DCR-SR220/SR210 HDR-CX520V/CX520/CX505V/CX500V/CX500, 1 DCR-SR88/SR85/SR78/SR75/SR68/SR65/SR58/SR55/ I-2 SR46/SR45/SR36/SR35 2 HDR-XR350V/XR350 HDR-CX120/CX106/CX105/CX100, J 1 DCR-SX60/SX50/SX41/SX40/SX31/SX30 K 1 DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 HDR-CX550V/CX550, 1 HDR-XR550V/XR550 L 2 HDR-XR155/XR150 5 Si vous utilisez un autre sabot de montage que le F-2/numéro 3, détachez la plaquette à vis c du sabot de montage de caméscope F-2/numéro 3. Alignez ensuite la plaquette à vis sur le numéro correct sur le sabot de montage de caméscope choisi, puis appuyez dessus de sorte qu’elle s’encliquette. La plaquette à vis a été fixée au sabot de montage F-2/numéro 3 en usine. Si vous utilisez le sabot de montage F-2/numéro 3, cette étape est inutile. Préparation du caméscope Pour le détail, reportez-vous au mode d’emploi fourni avec le caméscope. 1 Détachez l’accessoire. Retirez le filtre, le convertisseur, le capuchon d’objectif, le pare-soleil ou la bandoulière du caméscope. Si le caméscope que vous utilisez est pourvu d’un obturateur central manuel, ouvrez cet obturateur. 2 Installez la batterie. Installez une batterie complètement rechargée. 3 Introduisez le support. Pour les types de cartes mémoire (« Memory Stick Duo », carte SD) compatibles avec votre caméscope, reportez-vous au mode d’emploi du caméscope. Remarques Désactivez le taquet de sécurité de la carte mémoire et de la cassette pour permettre l’enregistrement. Assurez-vous que l’espace sur la cassette, la carte mémoire, le disque dur et dans la mémoire interne est suffisant pour l’enregistrement. Assurez-vous que le disque n’a pas été finalisé. 4 Fixez la bague antireflet (-3- d ) sur le filetage de l’objectif du caméscope. La bague antireflet empêche la lumière extérieure de se réfléchir dans le caisson sport (appelé ci-dessous « ce boîtier ») et de pénétrer dans l’objectif. Si vous utilisez un caméscope sans bague antireflet, la lumière extérieure venant de l’arrière se réfléchira sur ce boîtier. Dans la mesure du possible évitez de filmer avec le soleil dans le dos. Bague antireflet Bague antireflet (M30 × ø 43) Bague antireflet (M30 × ø 47) Bague antireflet (M30 × ø 50) Bague antireflet (M30 × ø 58) Bague antireflet (M30 × ø 62) Bague antireflet (M37 × ø 49) Caméscope HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD708/DVD608/DVD510/DVD308/ DVD306/DVD109/DVD108/DVD106, DCR-HC62/HC54/HC53/HC52/HC51/HC48/HC47/ HC45/HC38/HC37 HDR-CX360V/CX360/CX120/CX106/CX105/CX100, HDR-XR155/XR150, DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 DCR-DVD850/DVD810/DVD710/DVD650/DVD610/ DVD450/DVD410/DVD310/DVD150/DVD115/DVD110, DCR-SR88/SR78/SR68/SR58 HDR-XR350V/XR350, DCR-SR85/SR75/SR65/SR55/SR46/SR45/SR36/SR35 HDR-PJ50V/PJ50/PJ40V/PJ30V/PJ30, HDR-XR200V/XR200/XR106/XR105/XR101/XR100, HDR-SR10, DCR-SR220/SR210 HDR-CX700V/CX700/CX690/CX560V/CX560 HDR-PJ20/PJ10, HDR-CX550V/CX550/CX520V/CX520/CX505V/CX500V/ CX500/CX12/CX11/CX7/CX6, Bague antireflet HDR-XR550V/XR550/XR520V/XR520/XR500V/XR500/ (M37 × ø 55) XR160, HDR-SR12/SR11/SR8/SR7/SR5, HDR-HC9/HC7/HC5 Impossible de fixer la bague DCR-SX60/SX50/SX41/SX40/SX31/SX30 antireflet fournie 5 Tournez le panneau LCD vers l’extérieur et appliquez-le contre le caméscope. 6 Réglez la mise au point, l’éclairage, etc. sur AUTO. Installation du caméscope Si vous utilisez un HDR-XR520V/XR520/XR500V/XR500 (Voir l’illustration -4-A) Ouvrez le cache-prise et branchez la fiche. (Rangez le câble raccordé à ce boîtier en formant une boucle vers l’arrière de la fiche, comme indiqué sur l’illustration.) Installez le caméscope dans ce boîtier, en prenant soin de ne pas coincer le câble dans les pièces à l’intérieur de ce boîtier. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope. Si vous utilisez un HDR-XR200V/XR200/XR106/XR105/XR101/XR100 (Voir l’illustration -4-B) Ouvrez le cache-prise et branchez la fiche. Rangez le câble raccordé à ce boîtier en formant une boucle vers l’arrière de la fiche, comme indiqué sur l’illustration. Installez le caméscope dans ce boîtier, en prenant soin de ne pas coincer le câble dans les pièces à l’intérieur de ce boîtier. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope. Si vous utilisez le HDR-SR12/SR11/SR10, DCR-SR220/SR210 (Voir l’illustration -4-C) Ouvrez le cache-prise et branchez la fiche. (Rangez le câble raccordé à ce boîtier en formant une boucle vers l’arrière de la fiche, comme indiqué sur l’illustration.) Après avoir installé le caméscope dans ce boîtier, appuyez légèrement sur le câble pour le ranger du côté de la sangle du caméscope. Si vous utilisez le HDR-PJ50V/PJ50, HDR-XR160 ou le HDR-SR8/SR7/SR5 (Voir l’illustration -4-D) Ouvrez le cache-prise. Branchez la prise. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope. Si vous utilisez le HDR-XR350V/XR350/XR155/XR150 ou le HDR-CX120/CX106/ CX105/CX100 (Voir l’illustration -4-E) Ouvrez le cache-prise et branchez la fiche. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope, en prenant soin de ne pas coincer le câble sur le sabot de montage de caméscope ou d’autres pièces. Si vous utilisez le HDR-CX12/CX11/CX7/CX6 (Voir l’illustration -4-F) Ouvrez le cache-prise. Branchez la prise. Placez le câble sur le sabot de montage de caméscope et installez le caméscope dans ce boîtier. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope, en le plaçant de sorte qu’il ne tombe pas du sabot de montage de caméscope. Si vous utilisez le HDR-UX20/UX19/UX10/UX9 ou le DCR-DVD910/DVD510 (Voir l’illustration -4-G) (Si les points et suivants ont déjà été effectués à l’étape -3, continuez par .) Branchez la prise. Fixez le sabot de montage de caméscope au caméscope. Après avoir installé le caméscope dans ce boîtier, rangez le câble. (Accrochez le câble au support de câble.) Si vous utilisez le HDR-HC9/HC7/HC5 (Voir l’illustration -4-H) Ouvrez le cache-prise. Branchez la prise. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope. Si vous utilisez le DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37 (Voir l’illustration -4-I) (Si les points et suivants ont déjà été effectués à l’étape -3, continuez par .) Branchez la fiche en ouvrant suffisamment le cache-prise pour ne pas coincer la base de la fiche. Fixez le sabot de montage de caméscope au caméscope. Installez le caméscope dans ce boîtier en rangeant le câble du côté de la sangle du caméscope. Fixez le câble avec le clip du sabot de montage de caméscope, en prenant soin de ne pas coincer le câble sur l’écran LCD. ˎˎ Si la batterie du caméscope est trop grosse pour faire passer le câble derrière, faites-le passer sur la batterie et fixez-le avec les clips. Si vous utilisez le HDR-CX520V/CX520/CX505V/CX500V/CX500 ou le DCRSR85/SR75/SR65/SR55/SR46/SR45/SR36/SR35 (Voir l’illustration -4-J) Ouvrez le cache-prise et branchez la fiche. (Rangez le câble raccordé à ce boîtier en formant une boucle vers l’arrière de la fiche, comme indiqué sur l’illustration.) Après avoir installé le caméscope dans ce boîtier, appuyez légèrement sur le câble pour le ranger du côté de la sangle du caméscope. Si vous utilisez le DCR-SX60/SX50/SX41/SX40/SX31/SX30 (Voir l’illustration -4-K) (Si les points et suivants ont déjà été effectués à l’étape -3, continuez par .) Levez la sangle et ouvrez le cache-prise pour brancher la fiche. Fixez le sabot de montage de caméscope au caméscope. Installez le caméscope dans ce boîtier avec le câble recourbé au-dessus du caméscope. Après avoir installé le caméscope dans ce boîtier, rangez le câble. (Accrochez le câble au support de câble.) Si vous utilisez le DCR-DVD850/DVD810/DVD710/DVD650/DVD610/DVD450/ DVD410/DVD310/DVD150/DVD115/DVD110 (Voir l’illustration -4-L) Ouvrez le cache-prise. Branchez la prise. Coincez le câble dans la rainure de la bague antireflet du côté de la sangle, comme indiqué sur l’illustration. Rangez le câble de la façon illustrée et fixez le sabot de montage de caméscope à ce boîtier. Remarques sur le câble : ˎˎ Ne tordez pas le câble. ˎˎ Veillez à ce que le câble ne ressorte pas de la rainure de la bague antireflet. Après avoir installé le caméscope dans ce boîtier, assurez-vous que le câble ne gêne pas l’objectif du caméscope. Si vous utilisez le DCR-DVD708/DVD608/DVD308/DVD306/DVD109/DVD108/ DVD106 (Voir l’illustration -4-M) Ouvrez le cache-prise. Branchez la prise. Après avoir installé le caméscope dans ce boîtier, rangez le câble. Si vous utilisez le HDR-CX550V/CX550/XR550V/XR550 ou le DCR-HC62/HC54/ HC53/HC52/HC51/HC48/HC47/HC45/HC38/HC37 (Voir l’illustration -4-N) Ouvrez le cache-prise. Branchez la prise. Après avoir installé le caméscope dans ce boîtier, rangez le câble. (Accrochez le câble au support de câble.) Si vous utilisez le DCR-SR88/SR78/SR68/SR58 (Voir l’illustration -4-O) Ouvrez le cache-prise. Branchez la prise. Coincez le câble dans la rainure de la bague antireflet de la façon illustrée. Rangez le câble de la façon illustrée et fixez le sabot de montage de caméscope à ce boîtier. Remarques sur le câble : ˎˎ Ne tordez pas le câble. ˎˎ Veillez à ce que le câble ne ressorte pas de la rainure de la bague antireflet. Après avoir installé le caméscope dans ce boîtier, assurez-vous que le câble ne gêne pas l’objectif du caméscope. Si vous utilisez le HDR-CX700V/CX700/CX690/CX560V/CX560 (Voir l’illustration -4-P) Ouvrez le cache-prise. Faites passer le câble sous la sangle du caméscope et branchez la fiche. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope. Si vous utilisez le HDR-PJ40V/PJ30V/PJ30/PJ20/PJ10 ou le HDR-CX360V/CX360 (Voir l’illustration -4-Q) Ouvrez le cache-prise et branchez la fiche. Après avoir installé le caméscope dans ce boîtier, rangez le câble du côté de la sangle du caméscope. 5 Fermez la partie arrière. Appuyez sur la partie arrière du boîtier pour le refermer et serrez les fermoirs jusqu’à ce qu’ils s’encliquettent. Remarques 㣫Ⓥ⇳ぇ#㠋〫#゛ᾋ゛2␣┟㴯#㾃≣ᡯ⏳#D2Y#ᵟ㈇/#D2Y#RXW#ᵟ㈇#₇ᴋ#D2Y# ␣┟㴯#ᵟ㈇ぇ#ᵟᵟ䇿#⬴ㇼ㿏ⵤⵓ゛1#+ⲓ⮓#6#㇏#┟ᷯㆷ#㊓ワ, ❯#ᢧᢧぇ#㣫Ⓥ⇳⏳#㈜㚠㿗#ῃぇᴋ#㣫Ⓥ⇳#ㄫ㵼#⳿⏳#❯#ᢧᢧ#⿕#⟷⟻#⾿㔴㇏# ᙷὓぇ#㠏#ᵛ㇃/#㊌ẏᴋ#Ⰳ␣ᙷ#ᬗ#ῃᣃ㐷#㣫Ⓥ⇳#ㄫ㵼#⳿㇏#Ἦ#⟷⟻ㆻ# ᲃ≣#ᮚᴿᵛ1 -4-C ⷦⱂ⳺ -4-D ⷦⱂ⳺ 1 2 3 a ⾻∏ぇ#⮛⓼㿓#Vrq|#ᾋ㐷㮯#KG#⢻ᾋ゛#㣫Ⓥ⇳#≿㧋᷋#⚆#ᾋ㐷㮯#⢻ᾋ゛#㣫Ⓥ⇳# ≿㧋᷋+㿏#%㍞Ἶᱦ%⇳#㿟,㇏#┟ᷯㆷ#┟ὗ#៤ᙷ2㐷つぇ⮓#⬣ㄠ㿗#ⲏ#ㇿᴋ# ㆷ#⾻ᵐᴿᵛ1 2 3 b 1# ᦡ#⇢㆞Ṧ#⫞ᇊ#➎㢂ⱞ☆# a #Ṧ#ⴆᅚ㩓ឲ៎1 2# ᦡ#⇢㆞Ṧ#៕Ⱚ#㮮#Ⅾ㕞Ⱞ#ⵚⱯឲ៎1 3# ዢầ#→㞢Ṧ#ⵚⳲ㩓ឲ៎1 ❯#ᢧᢧ⏳#㈘ㆷ#⬸㭓⋓#ᡯ#ⴛ㴯∠㇏#⏳#㋧㉿㿫⮓#VWDUW2VWRS# ⛻㴳/#Whohskrwr#⛻㴳/#Zlgh#⛻㴳#⚆#SKRWR#⛻㴳ㆻ#Ⰷᙷ⇴ㆳ⋓#㋧㈈㿏ᢧ# ḻ⋔#㿫#㍳ⵤⵓ゛1 4# ⪞ፒ#ᔲⰮ#ⲏㄓ㩓ឲ៎1 -3 ㍞Ἶᱦ#Ẳ⮞㟯#❲#☊㗇㩂ጚ 1# ➎㣖㌊㠓Ⱞ#⫧ឲ៎1 #㈗#㿫㊓#⛻㴳##ㆻ#䃋⬫㻓#⚠䀜ㆳ⋓#ⴣ⇳ὓⵓ㬟#⬸㭓⋓#゛㽿#ⴣ⇳᷋## #⏳#ⴣ⇳ὓⵓ㦓⮓#⛻㫫ㆻ#㼀ᴿᵛ1 #Ἦ⓫#❯㜫⏳#ぴᴿᵛ1 -4-H 2# ㍞Ἶᱦ#Ẳ⮞㟯#❲ᵆ≪㘚#⬎᧾⬎2ẖᾒ㞢#㧶᳖ዢ# b #Ṧ#᪦⪞ᖯឲ៎1 3# ⇢#ጚጚ⪺#≪ㄓᤆ#㍞Ἶᱦ#Ẳ⮞㟯#❲Ṧ#ⴆᅚ㩓ឲ៎1# -4-I 4 #➎㣖㌊㠓#ⷪ⌮㩂ጚ -4-F -4-G -4-E 4 1 ⷪ⌮㩂ጚ 䃋⬫㻓#⚠䀜ㆳ⋓#㣫Ⓥ⇳#ㄫ㵼#⳿㇏#㿓㔴#ᯯ⢃⏳#ᱻ⏯#⬸㭓⋓#㿫⮓# ㈗㈜㣏⏳#㻷#㣫Ⓥ⇳#ㄫ㵼#⳿⏳#㜓㜓䇿#ⴣ⇳ὓⵓ㬬ᴿᵛ1 ❯#ᢧᢧ⏳#㠓㿏㿓#ῃぇᴋ#㣫Ⓥ⇳#ㄫ㵼#⳿#I05ᙷ#❯#ᢧᢧぇ#⟷㚠ẏ〫# ㇿᴿᵛ1 -3 4# ៎ⰶ#㥆⪺☆#㍞Ἶᱦ#Ẳ⮞㟯#❲⬪#ⅲ㬢Ṧ#☊㗇㩓ឲ៎1 㣫Ⓥ⇳# ㄫ㵼#⳿ I05 3 5 4 -3- d J 4 K 4 -4-M L05 -4-N 4 5 -4-O M 4 N 4 O 4 5 㣫Ⓥ⇳ KGU0KF<2KF:2KF8/ GFU0GYG:3;2GYG93;2GYG63;2GYG6392 GYG43<2GYG43;2GYG439 GFU0KF952KF872KF862KF852KF842 KF7;2KF7:2KF782KF6;2KF6: KGU0F[452F[442F[:2F[9 KGU0SM83Y2SM832SM73Y2SM63Y2SM632 SM532SM43/ KGU0[U493/ KGU0VU;2VU:2VU8 KGU0F[:33Y2F[:332F[9<32F[893Y2 F[893 KGU0X[532X[4<2X[432X[</# GFU0GYG<432GYG;832GYG;432GYG:432 GYG9832GYG9432GYG8432GYG7832 GYG7432GYG6432GYG4832GYG4482 GYG443 KGU0F[693Y2F[693/ KGU0[U853Y2[U8532[U833Y2[U8332 [U533Y2[U5332[U4392[U4382[U4342 [U433/ KGU0VU452VU442VU43/# GFU0VU5532VU543 KGU0F[853Y2F[8532F[838Y2F[833Y2 F[833/ GFU0VU;;2VU;82VU:;2VU:82VU9;2VU982 VU8;2VU882VU792VU782VU692VU68 KGU0[U683Y2[U683 KGU0F[4532F[4392F[4382F[433/# GFU0V[932V[832V[742V[732V[642V[63 GFU0VU;:2VU::2VU9:2VU8:2VU7;2VU7:2 VU6;2VU6: KGU0F[883Y2F[883/ KGU0[U883Y2[U883 KGU0[U4882[U483 5# ㍞Ἶᱦ#Ẳ⮞㟯#❲#I052ᘂⅮ#6#ⱞ⭢ⱂ#㍞Ἶᱦ#Ẳ⮞㟯#❲Ṧ#▖⮓㩂# ᆧ⮚⪺#▦ძ#ᖂ▖#㧶ᳲⱞ㞢# c #Ṧ#㍞Ἶᱦ#Ẳ⮞㟯#❲#I052ᘂⅮ# 6ᵆ≪㘚#᪦⪞ᖞ⟗⟆⬎1#ዢẖᇊᖂ☆#▦ძ#ᖂ▖#㧶ᳲⱞ㞢Ṧ#☊㗇㩆# ㍞Ἶᱦ#Ẳ⮞㟯#❲ⱂ#⬖Ṣ#ⅲ㬢⬪#Ỉ㉾ᇊ#ⴆⱺẖ⪺#Ⲋጢ#ᨶጶ⺪# ᛶ᳖#ⷦ⟗⟆⬎1 -4-P 2 5 6 1 4 -4-K -3 -4-L c G 5 5 4 -4-J ⛿䂯 ❯#ᢧᢧ㇏#ᝬ㈜#㠓㿏#ⵓ#⬳ᙸᵷ#ᬏ⬣#㾃≿㴯ᴋ#㣫Ⓥ⇳#ㄫ㵼#⳿#I052ᮏ⛻# 6ぇ#㈜㚠ẏ〫#ㇿᴿᵛ1#㣫Ⓥ⇳#ㄫ㵼#⳿#I052ᮏ⛻#6⏳#⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ# #ᵟᙷ#㾻ㄋ㿏㐷#⿁ᴿᵛ1 -4-Q ⌮᧾⬎#㍞Ἶᱦ#ⷪ⌮㩂ጚ ㈇⮯㿓#ᬫㄠㆷ#㣫Ⓥ⇳㇏#⬣ㄠ⮛⓼⮓ḻ#㚯㋧㿏ⵤⵓ゛1 1# ⩋☢☆ẖṦ#᪦⪞ᖯឲ៎1 㣫Ⓥ⇳ぇ⮓#㾻㮧/#㥟⛻㉻#⊃㏿/#⊃㏿#㤘/#⊃㏿#䄻ὓ#₇ᴋ#〫ᣟ#ᪿㆻ# ⟻␣㿠ᴿᵛ1 ⲏṐ#⊃㏿#⯋㮧⏳#⬣ㄠ㿫⮓#㣫Ⓥ⇳⏳#⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ#⊃㏿#⯋㮧⏳#に〫# ㍳ⵤⵓ゛1 2# ℚ㘚ẖ㠓Ⱞ#ⲏㄓ㩓ឲ៎1 ⑃㠠㉻㿓#⚧㮧␣㶠ㆻ#㈜㚠㿏っ#㍳ⵤⵓ゛1 3# ⃢᧾⪞Ṧ#ᘍ➟ឲ៎1# ⬣ㄠ㎈#㣫Ⓥ⇳シ#䂯䃏㿏ᴋ#Ⓥ┟␣#㣫ὓ+%Phpru|#Vwlfn#Gxr%/#VG# 㣫ὓ,㇏#㋼⏏ぇ#㿫⮓ᴋ#㣫Ⓥ⇳㇏#⬣ㄠ⮛⓼⮓⏳#㚯㋧㿫#㍳ⵤⵓ゛1 ⷦⱂ⳺ Ⓥ┟␣#㣫ὓシ#㯃㽻㇏#⽧ᢧ㐷#㭤#㈗ㆻ#㿫㊓㿫⮓#♯㐷⏳#ᢧ⋔㿗#ⲏ#ㇿᴋ# ⬸㭓⋓#㿫#ᰊᴿᵛ1 㯃㽻/#Ⓥ┟␣#㣫ὓ/#ᾋⴛ㫣/#㿏ὓ#ᾋⴛ㫣#⚆#ᬫ⟷#Ⓥ┟␣ぇ#♯㐷⏳#㉷㈜㿗#ⲏ# ㇿᴋ#㠠⟻㿓#ᝬᙻ#ㇿᴋ㐷#䃌㿏ⵤⵓ゛1 ᾋⴛ㫣ᙷ#㶃ᮇ⇳㏿#ẏ㐷#⿁⿏㇃ㆻ#䃌㿏っ#㍳ⵤⵓ゛1 4# ℂ▖#ℓ⺪#ẫ#+060 d ,#Ⱞ#㍞Ἶᱦⱂ#㨮㘚#ⲏㄓ#ᖂ▖⪺#ⲏㄓ㩓ឲ៎1 ⚏⬣#⚠㐷#ㆷ#ワ⟷㇏#⣒#ⴛ㹣㢗㶠#+㿏#%⇢#ጚጚ%⇳#㿟,#ᬫ⟷⋓# ⚏⬣ẏ〫#⊃㏿⋓#Ὓ〫゛ᴋ#ㆻ#⚠㐷㿠ᴿᵛ1 ⚏⬣#⚠㐷##〽ᴋ#㣫Ⓥ⇳#┟ᷯㆻ#⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ#Ἓ⋓⟷㮧㇏#ワឈ#❯# ᢧᢧぇ⮓#⚏⬣Ạᴿᵛ1#ᙷᴜ㿓㿓#ㇳឈぇ#Ὠㆻ#ṃ␣㐷#⿁ḻ⋔#㿏ⵤⵓ゛1 ⚏⬣#⚠㐷# ⚏⬣#⚠㐷# +P63#啑#堬#76, ⚏⬣#⚠㐷# +P63#啑#堬#7:, ⚏⬣#⚠㐷# +P63#啑#堬#83, ⚏⬣#⚠㐷# +P63#啑#堬#8;, ⚏⬣#⚠㐷# +P63#啑#堬#95, 5 6 ⚏⬣#⚠㐷# +P6:#啑#堬#7<, Veillez à ne pas coincer les câbles lorsque vous fermez la partie arrière. Bien que le centre de l’objectif de certains modèles de caméscopes ne soit pas aligné sur le centre de la vitre avant de ce boîtier lorsque le caméscope est installé, la prise de vue s’effectue normalement. ⚏⬣#⚠㐷# +P6:#啑#堬#88, 㣫Ⓥ⇳ KGU0X[532X[4<2X[432X[</# GFU0GYG<432GYG:3;2GYG93;2GYG8432 GYG63;2GYG6392GYG43<2GYG43;2GYG439/# GFU0KF952KF872KF862KF852KF842KF7;2 KF7:2KF782KF6;2KF6: KGU0F[693Y2F[6932F[4532F[4392F[4382 F[433/ KGU0[U4882[U483/# GFU0VU;:2VU::2VU9:2VU8:2VU7;2VU7:2 VU6;2VU6: GFU0GYG;832GYG;432GYG:432GYG9832 GYG9432GYG7832GYG7432GYG6432GYG4832 GYG4482GYG443/# GFU0VU;;2VU:;2VU9;2VU8; KGU0[U683Y2[U683/# GFU0VU;82VU:82VU982VU882VU792VU782 VU692VU68 KGU0SM83Y2SM832SM73Y2SM63Y2SM63/ KGU0[U533Y2[U5332[U4392[U4382[U4342 [U433/ KGU0VU43/# GFU0VU5532VU543 KGU0F[:33Y2F[:332F[9<32F[893Y2F[893 KGU0SM532SM43/ KGU0F[883Y2F[8832F[853Y2F[8532 F[838Y2F[833Y2F[8332F[452F[442F[:2 F[9/ KGU0[U883Y2[U8832[U853Y2[U8532 [U833Y2[U8332[U493/ KGU0VU452VU442VU;2VU:2VU8/ KGU0KF<2KF:2KF8 GFU0V[932V[832V[742V[732V[642V[63 1 ⟷Ⰴẓ#⚏⬣#⚠㐷#ㆻ# ⟷㚠㿗#ⲏ#〽ᴿᵛ Remarques 2 5# OFG#㠒ᗺⰮ#ᢶᴎ☆#℀Ⱞ#㪏㩂ᵇ#㩞☆#៎⟆#㍞Ἶᱦ⪺#៕⨮# ᘍ➟ឲ៎1 6# ㇲ⳺ⱞᖂ#ⵚὯ#ⱂ#ጚតⰮ#DXWRᵆ#☎⳿㩓ឲ៎1 1 Appliquez une solution antibuée pour objectif sur la vitre avant. 3 Si vous utilisez un caméscope avec interrupteur POWER, réglez l’interrupteur POWER sur arrêt. Laissez aussi ce boîtier éteint. Si vous utilisez un caméscope avec interrupteur d’alimentation interne activé par l’écran LCD, vous n’avez pas besoin d’éteindre le caméscope. ˎˎ Après avoir installé le caméscope dans ce boîtier, vous pouvez allumer et éteindre le caméscope en appuyant sur le bouton POWER de ce boîtier. ˎˎ Si vous utilisez le HDR-HC9/HC7/HC5, mettez l’interrupteur POWER sur marche. Appliquez 2 ou 3 gouttes de la solution antibuée pour objectif fournie sur la face interne de la vitre avant de ce boîtier. Afin d’augmenter l’effet antibuée, utilisez le dessiccatif fourni. Pour plus de détails, reportez-vous à « Dessiccatif » dans mode d’emploi fourni. #⌮᧾⬎#㍞Ἶᱦ#ⲏㄓ㩂ጚ 2 Enlevez les matières étrangères, poussière, sable ou cheveux, du joint torique, de la rainure et des surfaces au contact du caméscope, et appliquez de la graisse régulièrement sur tout le joint torique. Si vous fermez le boîtier sans nettoyer ces parties, celles-ci risquent d’être endommagées et de laisser l’eau pénétrer à l’intérieur. Pour le détail sur l’entretien du joint torique, reportez-vous à « Entretien du joint torique » dans le mode d’emploi. 3 Fixez le sabot de montage de caméscope. Alignez la vis du sabot de montage de caméscope sur le filetage de pied photo sous le caméscope. Si un des modèles suivants est utilisé, ouvrez le cache-prise et insérez à fond la fiche Audio/Commande à distance dans la prise A/V, la prise A/V OUT ou la prise de commande à distance A/V : HDR-UX20/UX19/UX10/UX9, DCR-DVD910/DVD510, DCR-SR87/SR77/SR67/ SR57/SR48/SR47/SR38/SR37, DCR-SX60/SX50/SX41/SX40/SX31/SX30 ˎˎ Si vous utilisez le DCR-SR87/SR77/SR67/SR57/SR48/SR47/SR38/SR37, insérez la fiche Audio/Commande à distance en ouvrant suffisamment le cache-prise. (Voir l’illustration -4-I ) Si le cache-prise n’est pas suffisamment ouvert, la fiche Audio/Commande à distance peut être coincée et la connexion sera mauvaise. Fixez le sabot de montage de caméscope au caméscope en utilisant les pièces métalliques (-4- e ) de la bandoulière, comme indiqué sur l’illustration. 4 Raccordez la fiche et installez le caméscope. Insérez à fond la fiche Audio/Commande à distance dans la prise A/V, la prise A/V OUT ou la prise de commande à distance A/V selon le caméscope utilisé. (sauf modèles mentionnés à l’étape 3) Lorsque vous installez le caméscope dans ce boîtier, alignez le sabot de montage de caméscope sur le guide dans la partie avant de ce boîtier, puis poussez l’arrière du sabot de montage caméscope jusqu’à ce que le sabot s’encliquette. Remarques ˎˎ Veillez à tenir ce boîtier à l’horizontale lorsque vous installez le sabot de montage de caméscope. Si vous installez le sabot de montage de caméscope en inclinant le caméscope, vous risquez d’endommager le sabot ainsi que la partie avant du boîtier. ˎˎ Attention de ne pas masquer l’objectif, l’écran LCD, le viseur, le levier de zoom ou le bouton PHOTO avec le câble. ˎˎ Si vous utilisez un caméscope pourvu d’un interrupteur d’alimentation interne activé par l’écran LCD, le mode d’enregistrement de photos/lecture vidéo du caméscope se réglera sur le mode d’enregistrement vidéo lorsque vous branchez la fiche Audio/Commande à distance. SRZHU#ⴛㅻ㣏ᙷ#ㇿᴋ#㣫Ⓥ⇳⏳#⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ#SRZHU#ⴛㅻ㣏⏳#ᤳ# ㍳ⵤⵓ゛1#₇㿓#❯#ᢧᢧ㇏#㉻ㅇḻ#ᪿ#⬸㭓⋓#㿫#㍳ⵤⵓ゛1#OFG#䃋⓫㇏#ⴛㅻ㣤#㋧㈈ぇ# 㫣ẓ#ᬫ⟷#㉻ㅇ#ⴛㅻ㣏ᙷ#㈜㚠ẓ#㣫Ⓥ⇳⏳#⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ#㣫Ⓥ⇳㇏#㉻ㅇㆻ#᫃# 㾻ㄋᙷ#〽ᴿᵛ1 ⷦⱂ⳺ # ❯ ᢧᢧぇ 㣫Ⓥ⇳⏳ ㈜㚠㿓 䄻ᴋ ❯ ᢧᢧ㇏ POWER ⛻㴳ㆻ ᲃ≣⮓ 㣫Ⓥ⇳㇏ ㉻ㅇㆻ 㦓ᛧᬏ ᫃ ⲏ ㇿᴿᵛ. HDR-HC9/HC7/HC5⏳ ⬣ㄠ㿏ᴋ ᜴ㄧぇᴋ POWER ⴛㅻ㣏⏳ 㦓 ㍳ⵤⵓ゛. -4-I 1# ⩈#Ⰺẖ⪺#➟ጚ#ℓ⺪#ᳶ#⮓⩋Ⱞ#ṯឲ៎1 -4- e ⟷Ⰴẓ#ᢧ#⚠㐷#⊃㏿#ㄠ#5/#6#⚠ㄯㆻ#❯#ᢧᢧ㇏#⿕#㆗␣#⾿㔴ぇ#⚋⏼ᴿᵛ1#ᢧ# ⚠㐷#䄟ᝳ⏳#ᰉㇳ#ⲏ#ㇿḻ⋔#⟷Ⰴẓ#᛫㋧㊓⏳#⬣ㄠ㿏っ#㍳ⵤⵓ゛1#㈇⮯㿓#ᬫㄠㆷ# ⟷Ⰴẓ#⮛⓼⮓㇏#%᛫㋧㊓%⏳#㚯㋧㿏っ#㍳ⵤⵓ゛1 4 2# Rẫⱞᖂ#㬲##ዢ#℀ⱂ#⳻ㇳ⪺☆#ἦ⺪ᖂ#ᾒᲂ/#ἢẖ㍞ᱧ#ⱂ#ⱞ…⺲Ⱞ# ⴆᅚ㩆#㮮/#Rẫ⪺#ዊ㩂ᅶ#ዢẖ➎Ṧ#ṯឲ៎1 △㐿ㆻ#㊓ᛧ㿏㐷#⿁#❯㜫⏳#ᵢㆳ⓫#ᡯ#⟷⟻#Ⰷ⬸ẏ#△#⭇#び⊛ᙷ# ㇿᴿᵛ1 R㇏#㡟ᢀぇ#㿓#㈇⮯㿓#ᬫㄠㆷ#⬣ㄠ⮛⓼⮓㇏#%R㇏#㡟ᢀ%ㆻ#㚯㋧㿏っ# ㍳ⵤⵓ゛1 3# ㍞Ἶᱦ#Ẳ⮞㟯#❲Ṧ#ⲏㄓ㩓ឲ៎1 #㣫Ⓥ⇳#⚈⓫㇏#⬳ᙸᵷ#㈜㚠#ᬏ⬣ぇ#㣫Ⓥ⇳#ㄫ㵼#⳿㇏#ᬏ⬣#ㅻ㣏⏳#㠋ⵤⵓ゛1 #⾻∏#┟ᷯ㎈㇏#㿏ᬏ⏳#⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ#ᵟ㈇#㥛⛻⏳#に#゛ᾋ゛2␣┟㴯#㾃≣ ᡯ⏳#D2Y#ᵟ㈇/#D2Y#RXW#ᵟ㈇#₇ᴋ#D2Y#␣┟㴯#ᵟ㈇ぇ#ᵟᵟ䇿#⬴ㇼ㿏ⵤⵓ ゛= KGU0X[532X[4<2X[432X[</#GFU0GYG<432GYG843/#GFU0VU;:2 VU::2VU9:2VU8:2VU7;2VU7:2VU6;2VU6:/#GFU0V[932V[832V[742 V[732V[642V[63 # GFU0VU;:2VU::2VU9:2VU8:2VU7;2VU7:2VU6;2VU6:ㆻ#⬣ㄠ㿏ᴋ# ᜴ㄧぇᴋ#ᵟ㈇#㥛⛻ᙷ#㠠⟻䇿#に#⬸㭓⋓#゛ᾋ゛2␣┟㴯#㾃≣ᡯ⏳# ⬴ㇼ㿏ⵤⵓ゛1#+ᡯ#070L##㚯㋧,#ᵟ㈇#㥛⛻ᙷ#㠠⟻䇿#に␣㐷#⿁ㆳ⓫# ゛ᾋ゛2␣┟㴯#㾃≣ᡯᙷ#ᛯ⊛⮓#㊈Ⰴ#㌂㐷#⿁ᜃ#ẗ#ⲏ#ㇿᴿᵛ1 #ᡯᝳ#ᚐ#〫ᣟ#ᪿ㇏#Ⰴ#⟷㻿#+070 e ,ㆻ#⬣ㄠ㿫⮓#㣫Ⓥ⇳ぇ#㣫Ⓥ⇳#ㄫ 㵼#⳿⏳#⟷㚠㿠ᴿᵛ1 -4-A 4-B -4-D -4-C 4# 㧶᳖ዢṦ#⫚ᆚ㩂ᇊ#㍞ἾᱦṦ#ⲏㄓ㩓ឲ៎1 㣫Ⓥ⇳ぇ#㠋〫#゛ᾋ゛2␣┟㴯#㾃≣ᡯ⏳#D2Y#ᵟ㈇/#D2Y#RXW#ᵟ㈇#₇ᴋ#D2Y# ␣┟㴯#ᵟ㈇ぇ#ᵟᵟ䇿#⬴ㇼ㿏ⵤⵓ゛1#+ⲓ⮓#6#㇏#┟ᷯㆷ#㊓ワ, ❯#ᢧᢧぇ#㣫Ⓥ⇳⏳#㈜㚠㿗#ῃぇᴋ#㣫Ⓥ⇳#ㄫ㵼#⳿⏳#❯#ᢧᢧ#⿕#⟷⟻#⾿㔴㇏# ᙷὓぇ#㠏#ᵛ㇃/#㊌ẏᴋ#Ⰳ␣ᙷ#ᬗ#ῃᣃ㐷#㣫Ⓥ⇳#ㄫ㵼#⳿㇏#Ἦ#⟷⟻ㆻ# ᲃ≣#ᮚᴿᵛ1 ⷦⱂ⳺ # 㣫Ⓥ⇳#ㄫ㵼#⳿⏳#㈜㚠㿗#ῃぇᴋ#❯#ᢧᢧ⏳#ⲏ㹀ㆳ⋓#㆗㐷㿫#㍳ⵤⵓ゛1#㣫Ⓥ⇳# ㄫ㵼#⳿⏳#⮯⋓#⚠䀜ㆳ⋓#㈜㚠㿏⓫#㣫Ⓥ⇳#ㄫ㵼#⳿シ#⿕㔴#❯㜫ᙷ#Ⰷ⬸ẗ# び⊛ᙷ#ㇿᴿᵛ1 # ⊃㏿/#OFG#䃋⓫/#⡧㶃㮧/#㎃#≿⛻#₇ᴋ#SKRWR#⛻㴳ぇ#㥷⢋#ᛯ␣㐷# # 㣫Ⓥ⇳#ㄫ㵼#⳿⏳#㈜㚠㿗#ῃぇᴋ#❯#ᢧᢧ⏳#ⲏ㹀ㆳ⋓#㆗㐷㿫#㍳ⵤⵓ゛1#㣫Ⓥ⇳# ㄫ㵼#⳿⏳#⮯⋓#⚠䀜ㆳ⋓#㈜㚠㿏⓫#㣫Ⓥ⇳#ㄫ㵼#⳿シ#⿕㔴#❯㜫ᙷ#Ⰷ⬸ẗ# び⊛ᙷ#ㇿᴿᵛ1 # ⊃㏿/#OFG#䃋⓫/#⡧㶃㮧/#㎃#≿⛻#₇ᴋ#SKRWR#⛻㴳ぇ#㥷⢋#ᛯ␣㐷# ⿁ḻ⋔#㍳㇏㿏ⵤⵓ゛1 # OFG#䃋⓫㇏#ⴛㅻ㣤#㋧㈈ぇ#㫣ẓ#ᬫ⟷#㉻ㅇ#ⴛㅻ㣏ᙷ#㈜㚠ẓ#㣫Ⓥ⇳⏳# ⬣ㄠ㿏ᴋ#᜴ㄧぇᴋ#゛ᾋ゛2␣┟㴯#㾃≣ᡯ⏳#でᜧ㿏⓫#㣫Ⓥ⇳㇏#㊌㐷へ⬸#㞣へ# ┟ὓ2⢻ᾋ゛#㈣⭔#┟ὓ⏳#Ṑへ⬸#㞣へ#┟ὓ⋓#✷᜴ⵓ㬬ᴿᵛ1 KGU0[U853Y2[U8532[U833Y2[U833Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070D#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#に#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1#+ᡯᝳ#ᚐ#❯#ᢧᢧぇ#でᜧẓ#㥷⢋ ㆻ#㾃≣ᡯ#Ἓ㔴ㆳ⋓#ㅇ#ẏḻ⋔#㿠ᴿᵛ1, #❯#ᢧᢧ#ᬫ⟷㇏#⟷㻿ぇ#㥷⢋#ᛯ␣㐷#⿁ḻ⋔#㍳㇏㿫⮓#❯#ᢧᢧぇ#㣫Ⓥ⇳⏳#⮛ 㣏㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓#㿫#ᰊᴿ ᵛ1 KGU0[U533Y2[U5332[U4392[U4382[U4342[U433Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ# 070E#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#に#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #ᡯᝳ#ᚐ#❯#ᢧᢧぇ#でᜧẓ#㥷⢋ㆻ#㾃≣ᡯ#Ἓ㔴ㆳ⋓#ㅇ#ẏḻ⋔#㿠ᴿᵛ1 #❯#ᢧᢧ#ᬫ⟷㇏#⟷㻿ぇ#㥷⢋#ᛯ␣㐷#⿁ḻ⋔#㍳㇏㿫⮓#❯#ᢧᢧぇ#㣫Ⓥ⇳⏳#⮛ 㣏㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓#㿫#ᰊᴿ ᵛ1 KGU0VU452VU442VU43/#GFU0VU5532VU543Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ# 070F#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#に#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1#+ᡯᝳ#ᚐ#❯#ᢧᢧぇ#でᜧẓ#㥷⢋ ㆻ#㾃≣ᡯ#Ἓ㔴ㆳ⋓#ㅇ#ẏḻ⋔#㿠ᴿᵛ1, #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆻ#⬫㑔#ᲃ≣⮓#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓# 㿫#ᰊᴿᵛ1 KGU0SM83Y2SM83偭KGU0[U493##KGU0VU;2VU:2VU8Ṧ#▖⮓㩂#ᆧ ⮚+ዢẦ#070G#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓#㿫#ᰊᴿ ᵛ1 KGU0[U683Y2[U6832[U4882[U483##KGU0F[4532F[4392F[4382 F[433Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070H#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#に#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳#ㄫ㵼#⳿#₇ᴋ#ᢧ㬷#⟷㻿ぇ#㥷⢋#ᛯ␣㐷#⿁ḻ⋔#㍳㇏㿫⮓#㣫Ⓥ⇳⏳# ❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓#㿫#ᰊᴿᵛ1 KGU0F[452F[442F[:2F[9Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070I#ㄢⵚ,# #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㥷⢋ㆻ#㣫Ⓥ⇳#ㄫ㵼#⳿#ㅻぇ#ィ⊛ᰊ#㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#㈜㚠㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㣫Ⓥ⇳#ㄫ㵼#⳿⋓⟷㮧#㥷⢋#‟〫㐷㐷#⿁ ḻ⋔#㿫⮓#㥷⢋ㆻ#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓#㿫#ᰊᴿᵛ1 KGU0X[532X[4<2X[432X[<##GFU0GYG<432GYG843Ⱞ#▖⮓㩂#ᆧ⮚ +ዢẦ#070J#ㄢⵚ,## +✆☆#06⪺☆#៎ⰶⱂ#ᇦ#Ṧ#Ẳ㇎Ⱞ#ᨶ⪺#Ⱖᵆ#⺮㩳㩂⟗⟆⬎1,## #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳#ㄫ㵼#⳿⏳#㣫Ⓥ⇳ぇ#㈜㚠㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻#㥷⢋ㆻ#㊌⊣㿠ᴿᵛ1#+㥷⢋ㆷ#㥷⢋#䂷᷋ぇ# ᛯ〫#ᰊᴿᵛ1, KGU0KF<2KF:2KF8Ṧ#▖⮓㩂#ᆧ⮚+ዢẦ#070K#ㄢⵚ,## #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓#㿫#ᰊᴿ ᵛ1 GFU0VU;:2VU::2VU9:2VU8:2VU7;2VU7:2VU6;2VU6:Ⱞ#▖⮓㩂#ᆧ⮚ +ዢẦ#070L#ㄢⵚ,## +✆☆#06⪺☆#៎ⰶⱂ#ᇦ#Ṧ#Ẳ㇎Ⱞ#ᨶ⪺#Ⱖᵆ#⺮㩳㩂⟗⟆⬎1,## #㾃≣ᡯ#✗ⴛ#⟷⟻ぇ#ᛯ␣㐷#⿁ḻ⋔#ᵟ㈇#㥛⛻⏳#㠠⟻䇿#に〫⮓#㾃≣ᡯ⏳#⟷㚠 㿠ᴿᵛ1 #㣫Ⓥ⇳#ㄫ㵼#⳿⏳#㣫Ⓥ⇳ぇ#㈜㚠㿠ᴿᵛ1 #㥷⢋#㣫Ⓥ⇳#ㆎ㔴ぇ#゛ḻ⋔#㿫⮓#㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿠ᴿᵛ1 #OFG#䃋⓫ぇ#㥷⢋#ᛯ␣㐷#⿁ḻ⋔#㍳㇏㿫⮓#㣫Ⓥ⇳#ㄫ㵼#⳿㇏#㫫ぇ#㥷 ⢋ㆻ#㊌㿠ᴿᵛ1 # 㣫Ⓥ⇳#⚧㮧␣#Ἓ⋓#㥷⢋ㆻ#㰬ᝳⵓ㬛ᢧぇ#⚧㮧␣ᙷ#▫#㫧#᜴ㄧぇᴋ# ⚧㮧␣#ㅻ⋓#㥷⢋ㆻ#㰬ᝳⵓ㬟#䄻#㫫ㆳ⋓#㥷⢋ㆻ#㊌㿫#㍳ⵤⵓ゛1 KGU0F[853Y2F[8532F[838Y2F[833Y2F[833##GFU0VU;82VU:82 VU982VU882VU792VU782VU692VU68Ṧ#▖⮓㩂#ᆧ⮚+ዢẦ#070M#ㄢⵚ,# #ᵟ㈇#㥛⛻⏳#に#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1#+ᡯᝳ#ᚐ#❯#ᢧᢧぇ#でᜧẓ#㥷⢋ ㆻ#㾃≣ᡯ#Ἓ㔴ㆳ⋓#ㅇ#ẏḻ⋔#㿠ᴿᵛ1, #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆻ#⬫㑔#ᲃ≣⮓#㣫Ⓥ⇳#ᡯ#✟㴯#㔴ㆳ⋓# 㿫#ᰊᴿᵛ1 GFU0V[932V[832V[742V[732V[642V[63Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070N# ㄢⵚ,# +✆☆#06⪺☆#៎ⰶⱂ#ᇦ#Ṧ#Ẳ㇎Ⱞ#ᨶ⪺#Ⱖᵆ#⺮㩳㩂⟗⟆⬎1, #ᡯ#✟㴯⏳#Ὓ〫ィ␣#ᵟ㈇#㥛⛻⏳#に〫⮓#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳#ㄫ㵼#⳿⏳#㣫Ⓥ⇳ぇ#㈜㚠㿠ᴿᵛ1 #㥷⢋#㣫Ⓥ⇳#ㆎ㔴ぇ⮓#⑇␣ḻ⋔#㿫⮓#㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻#㥷⢋ㆻ#㊌⊣㿠ᴿᵛ1#+㥷⢋ㆷ#㥷⢋#䂷᷋ぇ# ᛯ〫#ᰊᴿᵛ1, GFU0GYG;832GYG;432GYG:432GYG9832GYG9432GYG7832GYG7432 GYG6432GYG4832GYG4482GYG443Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070O#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #ᡯᝳ#ᚐ#㥷⢋ㆻ#ᡯ#✟㴯#㔴㇏#⚏⬣#⚠㐷##䂿ぇ#ㄸᴿᵛ1 #ᡯᝳ#ᚐ#㥷⢋ㆻ#㊌⊣㿫⮓#㣫Ⓥ⇳#ㄫ㵼#⳿⏳#❯#ᢧᢧぇ#㈜㚠㿠ᴿᵛ1 ⲏㄓ㩊#ᨶⱂ#ⷦⱂ=## # 㥷⢋ㆻ#៣⟷␣㐷#ⵤⵓ゛1 # 㥷⢋#⚏⬣#⚠㐷##䂿ぇ⮓#⣗㐷㐷#⿁ḻ⋔#㿏ⵤⵓ゛1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻#㥷⢋#⢻ᾋ゛#㣫Ⓥ⇳㇏#⊃㏿ぇ#ᛯ␣㐷#⿁⿏ᴋ 㐷#䃌㿠ᴿᵛ1 GFU0GYG:3;2GYG93;2GYG63;2GYG6392GYG43<2GYG43;2GYG439Ⱞ#▖ ⮓㩂#ᆧ⮚+ዢẦ#070P#ㄢⵚ,## #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻#㥷⢋ㆻ#㊌⊣㿠ᴿᵛ1 KGU0F[883Y2F[8832[U883Y2[U883##GFU0KF952KF872KF862 KF852KF842KF7;2KF7:2KF782KF6;2KF6:Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070Q# ㄢⵚ,# #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻#㥷⢋ㆻ#㊌⊣㿠ᴿᵛ1#+㥷⢋ㆷ#㥷⢋#䂷᷋ぇ# ᛯ〫#ᰊᴿᵛ1, GFU0VU;;2VU:;2VU9;2VU8;Ⱞ#▖⮓㩂#ᆧ⮚+ዢẦ#070R#ㄢⵚ,# #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #ᡯᝳ#ᚐ#㥷⢋ㆻ#⚏⬣#⚠㐷##䂿ぇ#ㄸᴿᵛ1 #ᡯᝳ#ᚐ#㥷⢋ㆻ#㊌⊣㿫⮓#㣫Ⓥ⇳#ㄫ㵼#⳿⏳#❯#ᢧᢧぇ#㈜㚠㿠ᴿᵛ1 ⲏㄓ㩊#ᨶⱂ#ⷦⱂ=# # 㥷⢋ㆻ#៣⟷␣㐷#ⵤⵓ゛1 # 㥷⢋#⚏⬣#⚠㐷##䂿ぇ⮓#⣗㐷㐷#⿁ḻ⋔#㿏ⵤⵓ゛1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻#㥷⢋#⢻ᾋ゛#㣫Ⓥ⇳㇏#⊃㏿ぇ#ᛯ␣㐷#⿁⿏ᴋ 㐷#䃌㿠ᴿᵛ1 KGU0F[:33Y2F[:332F[9<32F[893Y2F[893Ṧ#▖⮓㩂#ᆧ⮚+ዢẦ# 070S#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#ぴᴿᵛ1 #㥷⢋ㆻ#㣫Ⓥ⇳㇏#ᡯ#✟㴯#⾻∏⋓#㰬ᝳⵓ㬛#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳㇏#ᡯ#✟㴯#㔴ㆳ⋓# ㊌⊣㿠ᴿᵛ1 KGU0SM73Y2SM63Y2SM632SM532SM43##KGU0F[693Y2F[693Ṧ# ▖⮓㩂#ᆧ⮚+ዢẦ#070T#ㄢⵚ, #ᵟ㈇#㥛⛻⏳#に#㾃≣ᡯ⏳#でᜧ㿠ᴿᵛ1 #㣫Ⓥ⇳⏳#❯#ᢧᢧぇ#⮛㣏㿓#䄻ぇ#㥷⢋ㆷ#㣫Ⓥ⇳㇏#ᡯ#✟㴯#㔴ㆳ⋓# ㊌⊣㿠ᴿᵛ1 5# ᦡ#⇢㆞Ṧ#៕➟ឲ៎1 Ἦ⓫#❯㜫⏳#ᲃ≣⮓#ᵢ#㈗ᢧᴋ#Ⰳ␣ᙷ#ᬗ#ῃᣃ㐷#⛻㫫ㆻ#㈗ᢀᴿᵛ1 ⷦⱂ⳺ # Ἦ⓫#❯㜫⏳#ᵢㆻ#ῃぇᴋ#㥷⢋#㐷#⿁ḻ⋔#㍳㇏㿏ⵤⵓ゛1 # ㇳ⟷#㣫Ⓥ⇳#┟ᷯ㇏#⊃㏿#㎈ⵣㆷ#⮛㣏㿗#ῃ#⊃㏿㇏#㎈ⵣ#❯#ᢧᢧ㇏#⿕#㆗␣# ㎈ⵣᝳ#ㇳ㣏㿏㐷#⿁ᴋ#᜴ㄧᙷ#ㇿ㐷⑃#㞣へぇᴋ#▯㊓#〽ᴿᵛ1
This document in other languages
- français: Sony SPK-HCG
- 日本語: Sony SPK-HCG