Download Sony MDX-C6500R User's Manual

MDX-C6400R/C6500R/C6500RX
SERVICE MANUAL
AEP Model
MDX-C6400R/C6500R/C6500RX
Ver 1.2 2001.12
UK Model
MDX-C6500R/C6500RX
Photo: MDX-C6500R
Model Name Using Similar Mechanism
NEW
Base Mechanism Type
MG-164NZ-138
Optical Pick-up Name
KMS-241C
SPECIFICATIONS
MD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
90 dB
10 – 20,000 Hz
Below measurable limit
General
Outputs
Tuner section
FM
Audio outputs*1
Power aerial relay control
lead
Power amplifier control
lead
Telephone ATT control
lead*2
Bass ±9 dB at 100 Hz
Treble ±9 dB at 10 kHz
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 183 mm
(w/h/d)
Approx. 182 × 53 × 162 mm
(w/h/d)
Approx. 1.2 kg
Parts for installation and
connections (1 set)
Front panel case (1)
87.5 – 108.0 MHz
External aerial connector
10.7 MHz/450 kHz
8 dBf
75 dB at 400 kHz
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6 % (stereo),
0.3 % (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
Tone controls
MW/LW
*1 Equipped with front and rear outputs:
MDX-C6500RX/C6500R only
Equipped with rear outputs: MDX-C6400R
*2 MDX-C6500RX/C6500R only
Tuning range
Aerial terminal
Intermediate frequency
Usable sensitivity
Selectivity
Signal-to-noise ratio
Tuning range
Aerial terminal
Intermediate frequency
Sensitivity
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
External aerial connector
10.7 MHz/450 kHz
MW: 30 µV
LW: 40 µV
Power amplifier section
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
U.S. and foreign patents licensed from Dolby
laboratories Licensing Corporation.
Design and specifications are subject to change
without notice.
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 50 W × 4 (at 4 ohms)
FM/MW/LW MINIDISC PLAYER
9-870-051-13
Sony Corporation
2001L0500-1
C 2001.12
e Vehicle Company
Published by Sony Engineering Corporation
TABLE OF CONTENTS
1.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
GENERAL
Location of controls ........................................................ 3
Installation ....................................................................... 4
Connections ..................................................................... 5
2.
DISASSEMBLY ......................................................... 9
3.
ELECTRICAL ADJUSTMENTS
Test Mode ........................................................................ 16
MD Section ..................................................................... 16
Tuner Section .................................................................. 16
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-12.
4-13.
4-14.
4-15.
4-16.
4-17.
4-18.
4-19.
Block Diagram – SERVO Section – ...............................
Block Diagram – TUNER Section – ..............................
Block Diagram – MAIN Section – .................................
Block Diagram – BUS CONTROL/
POWER SUPPLY Section – ...........................................
Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
Printed Wiring Boards
– SERVO Board (Component Side)/
SENSOR Board – ............................................................
Printed Wiring Board
– SERVO Board (Conductor Side) – ..............................
Schematic Diagram – SERVO Board (1/2) – .................
Schematic Diagram – SERVO Board (2/2) – .................
Printed Wiring Board
– MAIN Board (Component Side) – ..............................
Printed Wiring Board
– MAIN Board (Conductor Side) – ................................
Schematic Diagram – MAIN Board (1/3) – ...................
Schematic Diagram – MAIN Board (2/3) – ...................
Schematic Diagram – MAIN Board (3/3) – ...................
Printed Wiring Board – SUB Board – ............................
Schematic Diagram – SUB Board – ...............................
Printed Wiring Board – KEY Board – ............................
Schematic Diagram – KEY Board – ..............................
IC Pin Function Description ...........................................
5.
EXPLODED VIEWS ................................................ 50
6.
ELECTRICAL PARTS LIST ............................... 54
4-5.
4-6.
4-7.
4-8.
4-9.
4-10.
4-11.
17
18
19
20
21
22
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
Never look into the laser diode emission from right avove when
checking it for adustment. It is feared that you will lose your sight.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
(KMS-241C/J1NP).
The laser diode in the optical pick-up block may suffer electrostatic break-down easily. When handling it, perform soldering
bridge to the laser-tap on the flexible board. Also perform m easures
against electrostatic break-down sufficiently before the operation.
The flexible board is easily damaged and should be handled with
care.
23
24
25
26
27
28
29
30
32
33
34
35
40
laser-tap
OPTICAL PICK-UP FLEXIBLE BOARD
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
SECTION 1
GENERAL
Location of controls
This section is extracted from
instruction manual.
Setting the clock
The clock uses a 24-hour digital indication.
Example: To set the clock to 10:08
1
D I SC +
OPEN
-P R PTY DSPL
+
ST
MENU
D-BASS
LIST
SOURCE
Press (MENU), then press either side of
(DISC/PRST) repeatedly until “CLOCK”
appears.
TA
-SEEK/AMS
AF
SOUND
ENTER
PR
OFF
ST
--
D ISC –
MODE
REP
SHUF
1
2
3
4
5
6
1 Press (ENTER).
MDX-C6500RX/C6500R
/C6400R
The hour indication flashes.
Refer to the pages listed for details.
1 Volume control dial 19
2 MENU button 8, 10, 12, 13, 14, 15, 16,
18, 19, 21, 24
3 DISC/PRST +/– (cursor up/down) buttons
8, 10, 12, 13, 14, 15, 16, 18, 19, 20, 21, 24
During CD/MD playback:
Disc change 10, 13
During radio reception:
Preset stations select 16
4 Z (eject) button (located on the front
side of the unit behind the front panel)
9
5 DSPL/PTY (display mode change/
programme type) button 9, 10, 12, 17,
20
2 Press either side of (DISC/PRST) to set
the hour.
qf SEEK/AMS –/+ (cursor left/right) buttons
8, 10, 12, 14, 16, 18, 19, 21, 23, 24
Automatic Music Sensor 10, 14
Manual Search 10
Seek 15, 16, 18
3 Press the (+) side of (SEEK/AMS).
qg ENTER button 8, 10, 12, 13, 14, 15, 16,
18, 19, 20, 21, 24
qh MODE button 19
During CD or MD playback:
CD/MD unit select 9, 13
During radio reception:
BAND select 15, 16
The minute indication flashes.
4 Press either side of (DISC/PRST) to set
the minute.
qj Receptor for the card remote
commander
7 SOURCE (TUNER/CD/MD) button
8, 9, 10, 13, 15, 16, 19
qk Number buttons
During radio reception:
Preset number select 15, 16, 18, 19
During CD/MD playback:
(1) REP 11
(2) SHUF 11
8 Display window
ql AF button 17, 18, 19
9 OPEN button 7, 9, 26
w; TA button 18, 19
The clock starts.
* Warning when installing in a car
without ACC (accessory) position on
the ignition key switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily,
the clock display does not turn off and this
causes battery wear.
After the clock setting is completed, the
display returns to normal play mode.
6 LIST button 12
List-up 13
2
Press (ENTER).
q; D-BASS button 25
qa SOUND button 23
qs Reset button (located on the front side
of the unit behind the front panel) 7
qd OFF button* 7, 8, 9
Tip
You can set the clock automatically with the RDS
feature (see page 17).
Note
In the initial setting, the clock indication appears
while the unit is turned off.
When the D.INFO mode is set to ON, the time is
always displayed (page 24).
3
4
5
6
7
8
SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
SUB PANEL ASS’Y
1 screw
(PTT2.6 × 5)
2 cover
4 two claws
5 sub panel ass’y
3 screw
(PTT2.6 × 8)
4 claw
3 two screws
(PTT2.6 × 8)
6 flexible flat cable (CNP811)
3 screw
(PTT2.6 × 8)
MECHANISM DECK (MG-164NZ-138)
3 two screws
(PTT2.6 × 5)
4 bracket (MD)
5 mechanism deck
(MG-164NZ-138)
1 screw
(PTT2.6 × 5)
2 connector
(CN101)
1 screw
(PTT2.6 × 5)
9
SERVO BOARD
2 two screws
(BVTT2 × 4)
2 two screws
(BVTT2 × 4)
3 servo board
1 sensor flexible board
(CN102)
1 flexible board
(CN103)
MAIN BOARD
1 three ground point
screws
2 three screws
(PTT2.6 × 10)
3 main board
10
MD COVER ASS’Y
1 four screws
(B2 × 3)
3 MD cover ass’y
shaft (MD cover guide)
cassette holder
A
2 Pushing the Cassette Holder in the direction of the arrow A with a
screwdriver, etc., disengage the Shaft (MD Cover Guide) from
the slot in the MD Cover Assy.
Note: Take care not to scratch the optiocal Pick-up when pushing
the Cassette Holder with a screwdriver. etc.
HEAT SINK
1 three screws
(PTT2.6 × 10)
2 two screws
(PTT2.6 × 12)
1 screw
(PTT2.6 × 10)
3 heat sink
C6500R/C6500RX
1 two screws
(PTT2.6 × 10)
11
FLOAT BLOCK
3 Pushing an arrow A part, raise the float block
up ward at the front to release a lock.
1 tension spring (FLOAT B)
A
float block
lever (lock R)
lever (lock L)
1 tension spring (FLOAT B)
2 two tension springs (FLOAT F)
LO MOTOR ASS’Y (LOADING) (M903)
4 Remove the bracket (LO)
in the direction of the arrow A.
A
1 Remove solders of motor (M903)
5 LO motor ass’y (loading)
(M903)
2 tension spring (rack)
3 claw
bracket (LO)
– bottom view –
12
LEVER (LE) ASS’Y
2 stopper washer
2 lever (LE) ass’y
3 roller (GEAR E)
1
HOLDER ASS’Y
4 Remove the holder ass’y in the
direction of the arrow.
2 type-E stopring 1.5
1 spring (CHKG)
2 type-E stopring 1.5
2 type-E stopring 1.5
3 lever (lock R)
3 lever (lock L)
1 spring (CHKG)
2 type-E stopring 1.5
13
CHUCKING ARM ASS’Y
1 Remove the chucking arm ass’y
in the direction of the arrow.
holder ass’y
OPTICAL PICK-UP (KMS-241C/J1NP)
4 screw
(B2 × 3)
6 bearing (SL)
5 feed screw ass’y
7 optical pick-up
(KMS-241C/J1NP)
1 two screws
(K2 × 3)
2 guide shaft (OPT L)
14
3 screw
(K2 × 3)
SL MOTOR ASS’Y (SLED) (M902), SP MOTOR ASS’Y (SPINDLE) (M901)
4 screw
(P1.7 × 1.8)
9 two screws
(P1.7 × 1.8)
5 bracket (SL)
2 two screws
(2 × 8)
6 SL motor ass’y
(sled) (M902)
0 bracket (SP)
7 screw
(B2 × 3)
qa SP motor ass’y
(spindle) (M901)
3 sensor board
8 base (SL)
1 Remove solders of motors
(M901, M902)
15
SECTION 3
ELECTRICAL ADJUSTMENTS
TEST MODE
This set have the test mode function.
<Set the Test Mode>
1. Turn ON the regulated power supply. (The clock is displayed)
Note: Press the
2.
3.
4.
5.
[OFF]
button, if the clock is not displayed.
Push the preset [4] button.
Push the preset [5] button.
Press the preset [1] button for more than two seconds.
Then the display indicates all lights, the test mode is set.
<Release the Test mode>
1. Push the [OFF] button.
MD SECTION
MD section adjustments are done automatically in this set.
TUNER SECTION
Tuner section adjustments are done automatically in this set.
16
MDX-C6400R/C6500R/C6500RX
SECTION 4
DIAGRAMS
15
TX
BLOCK DIAGRAM – SERVO Section –
MORFI
40
AGCI
RF
RF AGC
& EQ
55
38
(Page 19)
ASYI
DADT
COMPARATOR
RFI
DIN
21
DOUT
22
DADT, BCK, LRCK, FS256
24
EQ
33
WBL
3T
F
TEMP
D-RAM
PEAK
B
XBCK
LRCK
FS256
26 25 27
AUX
B.P.F.
PEAK &
BOTTOM
BOTM
ADIN
ADFG
OSCI
CLOCK
GENERATOR
37
OSCO
E
8
9
F
FE
FOCUS
ERROR AMP
E
F
TE
TRACKING
ERROR AMP
I-V
AMP
SE
D0 – D3
35
34
79
F0CNT
CPU
INTERFACE
SPINDLE
SERVO
26
28
94 93 10
12
11
14
9 8
MONITOR
CONTROL
5 6 7
A00 – A09
ABCD
ABCD
AMP
78
32
MNT0
MNT1
MNT2
MNT3
C
D
I-V
AMP
30
SWDT
SCLK
XLAT
DETECTOR
29
B.P.F.
SENS
SRDT
E
A
B
C
D
INTERNAL BUS
XINT
4
5
6
7
SUBCODE
PROCESSOR
ADIP
DEMODULATOR/
DECODER
SQSY
A
ADFM
AT
AMP
XRST
DQSY
A
SPRD
D
J
SPFD
B
ADFG
C
1 2 3 4
WBL
3T
EQ
COMMAND
PD
10
V-I
CONVERTER
PD
12
LEVEL SHIFT
IC502
6
12
XOE
XWE
XRAS
XCAS
13
1
3
5
3 1
LEVEL SHIFT
IC503
4 2
41
45
44
42
20
22 OE
3 WE
4 RAS
23 CAS
12
2
4
6
LD
11
LD/PD
AMP
13
SWDT
SCLK
XLAT
PD
APC
5
SERIAL/
PARALLEL
CONVERTER,
DECODER
F0CNT
ILCC
APCREF
AUTOMATIC
POWER
CONTROL
Q302
17
X301
22.5792MHz
512FS OSC
IC304
D-RAM
IC307
16 17 18
OPTICAL PICK-UP BLOCK
(KMS-241C)
FOK
SHOCK
XBUSY
SLOCK
LASER DIODE
16
36
WBL
I
A
1, 2, 24, 25
D0 – D3
46
DIGITAL
AUDIO
INTERFACE
9 – 12, 14 – 18, 5
A0 – A9
RFO
SAMPLING
RATE
CONVERTER
47, 46, 48, 49
RF AMP
J
52
ASYO
DIGITAL SIGNAL PROCESSOR,
EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER,
ATRAC ENCODER/DECODER, 2M BIT D-RAM
IC301 (1/2)
32 – 29, 34 – 38, 43
2
I
PLL
: MD PLAY
23
BCK
LRCK
FS256
1
J
MORFO
I
ADDT
ATRAC
ENCODER/DECODER
FILTER
FILI
59
PCO
58
CLTV
61
FILO
60
51
• SIGNAL PATH
EFMO
RF AMP,
FOCUS/TRACKING ERROR AMP
IC302
48 47
IC301 (1/2)
SHOCK PROOF
MEMORY CONTROLLER
100
EFM/ACIRC
ENCODER/DECODER
4-1.
+3.3V
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC303
(Page 19)
RESET
FCS+
(FOCUS)
(TRACKING)
21 OUT1F
23 OUT1R
IN2F 29
IN2R 30
IN1F 19
IN1R 18
FFDR
88
FRDR
89
TRK–
IN3F 14
IN3R 15
TFDR
86
TRDR
85
39
66
MNT0
MNT1
MNT2
MNT3
TEMP
DEEMP
31 EXTAL
ANALOG MUX
LOCK 21
A-MUTE 67
7
6
63
11
56
FROM CPU
INTERFACE
XLRF
CKRF
DTRF
80
81
82
LOADING
MOTOR DRIVE
IC305
5
4
RIN
FIN
LOADING START/
EJECT END
OUT1 OUT2
1
7
DIGITAL SERVO
SIGNAL PROCESSOR
IC301 (2/2)
M903
(LOADING)
05
17
17
M
LOCK
B
C
(Page 19)
MD MECHANISM CONTROLLER
IC501 (1/2)
X501
10MHz
32 XTAL
AUTO
SEQUENCER
12 OUT3F
10 OUT3R
26 27 28 29
A/D CONVERTER
DIGITAL
SERVO
SIGNAL
PROCESS
FCS–
TRK+
45 51 64
LIMIT-IN
2-AXIS
DEVICE
M
27 OUT2F
25 OUT2R
PWM GENERATOR
M902
(SLED)
SFDR
92
SRDR
91
54 52
E-SW
83
55
66 75 64 65 74 73 62 63
C-SW
AUTOMATIC
POWER
CONTROL
62
MD-SO
MD-CKO
MD-LAT
APCREF
59
SENS
MD-SI
13
RECP
CC-XINT
+3.3V
IC306
LOAD
SPFD
SPRD
SQSY
IN4R 3
IN4F 4
EJECT
6 OUT4F
8 OUT4R
MD-RST
M
AUX1
AUX2
ABCD
FE
TE
SE
PEAK
BOTM
M901
(SPINDLE)
TH501
SWDT
SCLK
XLAT
ABCD
PEAK HOLD
Q301
EMPHASIS
PSB 16
RESET, EMPHASIS
ON: When the disc loading start
and the disc eject completion.
LOADING
END
ON: When completion of
the disc loading.
(LIMIT)
ON: When the optical pick-up is
inner position.
MD-ATT
D
(Page 19)
MDX-C6400R/C6500R/C6500RX
4-2.
BLOCK DIAGRAM – TUNER Section –
BU B+
TUNER +8.7V
TUNER +5.6V
RDS-DET
SDA (12CBUS)
SCL (12CBUS)
IF-AM
VDD (5V)
E
(Page 19)
F
(Page 19)
G
(Page 19)
I
(Page 19)
H
(Page 19)
MUTING
Q111
S-METER
VCC (8.5V)
MPX
MPX 10
FM-AGC
ANT-AM
16
17 18
4
14
9
12 13
19
AM-DET
AM
8
MUTING
Q121
D131
MUTING
CONTROL SWITCH
Q131
DATA
CLOCK
IF-AM
DATA, CLOCK
DATA
CLOCK
RDS DECODER
IC51
SC
57 kHz
OUT
18
16
BAND-PASS
MPX
FILTER
MPTH
5
SIGNAL
QUALITY
DECODER
CLOCKED
COMPARATOR
4
RDS/RDBS
DEMODULATOR
& DECODER
5
DAVN
2
4
INTERFACE
REGISTER
IIC BUS
SLAVE
TRANSCEIVER
SDA
9
SCL
10
BUFFER
Q1
OSCILLATOR
& CLOCK
OSCO
MULTI
PATH
DETECTOR
CIN
OSCI
20
LVIN
19
BAND-PASS
FILTER
IC90
8
Q90
NOISE DET
DISCHARGE
SWITCH
X51
4.332MHz
VSM
MPTH
64
50
32
56
TUNATT
52
NS MASK
53
QUALITY
51
DAVN
9 10
FMAGC
S-METER
E2P SIO
E2P CKO
1
5
SDA (E2PROM)
SCL (E2PROM)
2 ANT-FM
11
VDD E2P (5V)
FM/AM TUNER UNIT
TU1
J1
(FM/AM ANTENNA)
MASTER CONTROLLER
IC501 (1/3)
• SIGNAL PATH
: FM
: MW/LW
05
18
18
MDX-C6400R/C6500R/C6500RX
CNJ151 (1/2)
(L)
BUS
AUDIO IN
(R)
INPUT SELECT,
ELECTRICAL VOLUME, FM MPX
IC151
R-CH
LRCK
6
4
DATA
BCK
LRCK
3
VOUTL
1
12
11
VOUTR
9
LOUDNESS/
VOLUME
SEL
AM
R-CH
SOFT
MUTE
MUTE
TONE
CONTROL
OUTPUT
SELECTOR
BCK
5
FD1L
INPUT
MULTIPLEXER
DADT
D/A
COMVERTER
CNJ151 (2/2)
NOISE
SHAPER
A
DADT,
BCK,
LRCK,
FS256
DIGITAL
FILTER
(Page 17)
BLOCK DIAGRAM – MAIN Section –
INPUT
INTERFACE
4-3.
LOUDNESS
OUTLF
MONO
FADER
MIXER
OUTLR
(L)
30
29
MUTING
Q171
AUDIO OUT
FRONT
R-CH
RESET,
EMPHASIS
RESET
15
CLK
CONTROL
MODE
CONTROL
12
DIGITAL FILTER,
D/A CONVERTER
IC101
RSTB
17
13
AMIF
AM/FM
NOISE
BLANKER
MPX
(Page 18)
E
HIGH-CUT
R-CH
R-CH
AUDIO OUT
(R)
(C6400R)
MUTING
Q281
D/A
CONVERTER
DIGITAL
CONTROL
IF-AM
CN601 (1/2)
(POWER CONNECTOR)
POWER AMP
IC611
IIC BUS
1
MPX
20
SM
G
S&H
PILOT
DET
SCL
(Page 18)
L.P.F.
AM
SDA
F
(C6500R, C6500RX)
MUTING
Q181
DEMODULATOR
+STEREO ADJUST
+STEREO BLEND
16
PLL
AUDIO OUT
REAR
(L)
PILOT
CANCELATION
L.P.F.
EMPHASIS
(Page 18)
(C6500R, C6500RX)
MUTING
Q271
LEVEL
B
XTI
DM0
(Page 17)
1
DM1
FS256
(R)
21
FL+
12 FL-IN
D621
14
18
5
FRONT L (+)
9
FL–
3
FRONT L (–)
4
FR+ 21
14 FR-IN
(Page 18)
I
DATA, CLOCK
DATA
FR– 23
RL+
9
11 RL-IN
(Page 17)
H
C
FRONT R (–)
2
CLOCK
(Page 18)
FRONT R (+)
12
S-METER
REAR L (+)
10
RL–
7
REAR L (–)
3
LOCK
RR+ 17
REIN0
REIN1
KEYACK
AD-ON
NOSESW
DOORSW
LCDSO
LCDCKO
LCDCE
X1
X0
X1A
X0A
ATT
TELATT
TEST IN
VOLATT
BEEP 16
46
47
36
37
76
35
67
12
13 14 15
93
92
73
74
58
79
81
REAR R (–)
16 AUX IN
22 MUTE
AMPATT 60
48 85
RCIN0
REAR R (+)
11
RR– 19
KEYIN1
57
KEYIN0
71
RCIN1
MASTER CONTROLLER
IC501 (2/3)
70
I2C CKO
LOCKIN
84
I2C SIO
15 RR-IN
AMPON 59
4
STNBY
15
TEST
KEY ACTIVE
SWITCH
Q651, 652
U-COM +5V
14
X501
3.68MHz
CN500
MAIN BODY SIDE
X502
32.768kHz
LEVEL SHIFT
Q571
SW504
(NOSE DETECT)
D622
SE
DI
1
D501
BACK-UP B+
REMOTE IN
LSW810,
LSW901 – 917,
S901 – 904
ROTARY
ENCODER
RE901
VOLUME/BASS/TREBLE/
BALANCE/FADER CONTROL
TEL-ATT
D571
(C6500R, C6500RX)
64 63 62
CN901
FRONT PANEL SIDE
CL
J501
13
OSC
C953, R957
D653
LIQUID CRYSTAL
DISPLAY DRIVER
IC901
60 OSC
S04 – S51
COM1 – COM4
4 – 51
52 – 55
BATTERY OFF
MUTE DRIVER
Q621
D502
MUTING
CONTROL SWITCH
Q622
• SIGNAL PATH
: MD PLAY
: FM
LCD901
LIQUID CRYSTAL DISPLAY
(Page 17)
D
MD-ATT
05
19
19
D302
: MW/LW
: BUS AUDIO IN
MDX-C6400R/C6500R/C6500RX
4-4.
BLOCK DIAGRAM – BUS CONTROL/POWER SUPPLY Section –
REMOTE CONTROL
RECEIVER
IC951
CN701
BUS CONTROL IN
MASTER CONTROLLER
IC501 (3/3)
(FOR SONY BUS)
D708
3
SIRCS BUFFER
Q704
SIRCS
CN601 (2/2)
(POWER CONNECTOR)
24 SIRCS
D673
6
ANT-R
RESET SIGNAL
GENERATOR
IC652
BU B+
D674
90 RSTX
AMP-R
86 HSTX
5
6 AMP+B
8 ANT+B
SW503
RESET
D301
SONY BUS INTERFACE
IC701
2
5
RST
RESET
SWITCH
DATA
RST
DATA IN
6
DATA
DATA OUT
TUNER +8.7V
13
TUNER +5.6V
11 SYSRST
VCC 7
10 TU5.6V
RDS DECODER
(IC51) B+
9
18 UNISO
8
17 UNISI
11
19 UNICKO
COM +8V
(AUDIO CIRCUIT B+)
9 COM8V
1
BUS ON
7
BATT
3
PULL UP +5V
3 BUSON
D701
BACK-UP B+
3
2
D677
U-COM +5V
PW ON 120
TUNON 1
BATTERY BU IN
10
SWITCH
77 BUIN
LCD B+
LCD DRIVER
(IC901) B+
D702
TH701
4
5 BU+B
D676
20 UNICKI
BUS ON
BUS
OUT
BUS ON ON IN
12
SWITCH
BATT
BU B+
8.7VON SW
BUS ON SWITCH
Q705
CLK IN
CLK
5.6VON SW
4
STB
D1
4
CLK
REGULATOR
Q631
LED901-904,
LED910-915,
LSW901-917
BATTERY
DETECT
Q701
ILLON 7
D662
ACCESSORY CHECK
Q661
ACC IN 82
LED810
(MD DISC SLOT)
DOORIND 29
LSW810
Z
LED810,
LSW810
LO- +12V
LOADING MOTOR
DRIVER (IC305) B+
MD MECHANISM CONTROLLER
IC501 (2/2)
B+ SWITCH
Q402, 403
60 BU-IN
30 RESET
49 UNISI
48 UNICKIO
LEVEL SHIFT
Q706
MDMON 10
REGULATOR
CONTROL SWITCH
Q363
50 UNISO
+3.3V
46 LINKOFF
REGULATOR
CONTROL SWITCH
Q250
05
20
20
16
+B
+3.3V
REGULATOR
IC401, Q401
7
ACC
REGULATOR
Q551
+12V
REGULATOR
Q361
MD-ON 65
61 BUS-ON
FU601
REGULATOR
CONTROL SWITCH
Q633
VCC
6
REGULATOR
IC671
11 TU8.7V
D2
2
RESET
BACK-UP B+
POWER AMP
(IC611) B+
DRIVER +5V
MOTOR/COIL DRIVER
(IC303) B+
+5V
REGULATOR
Q362
MDX-C6400R/C6500R/C6500RX
• Circuit Boards Location
4-5.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
z
•
: Through hole.
f
: internal component.
•
• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
SENSOR board
SERVO board
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
SUB board
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
% : indicates tolerance.
f
•
: internal component.
• C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• U : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E : MD PLAY
F : FM
f : MW/LW
L : BUS AUDIO IN
KEY board
MAIN board
21
21
MDX-C6400R/C6500R/C6500RX
4-6. PRINTED WIRING BOARDS – SERVO Board (Component Side)/SENSOR Board –
1
2
3
4
5
6
• See page 21 for Circuit Boards Location.
7
8
9
10
11
12
13
14
15
16
17
A
(LOADING END)
(COMPONENT SIDE)
5
L101
C103
C105
20
11
C109
+
B
E
8
1
C402
C
M
C108
C306
BLK
R406
C403
Q401
C11
A
D401
C352
1
8
IC101
R319
C304
C305
29
R316
1
FB301
4
10
R311
R312
R318
5
C104
R102
R320
C308
30
+ C106
11
C
IC305
L102
R317
(CHASSIS)
50
C107
26
FB302
CN103
25
8
R325
5
8
7
R354
R324
1
D
(CHASSIS)
11
C341
51
IC304
C310
IC301
R327
CN101
X301
4
IC502
C340
R328
1
SENSOR FLEXIBLE
BOARD
C311
75
1
D501
K
R307
1
M
8
BLK
7
A
R304
IC503
R303
R330
C339
G
C343
R517
1
(Page
27)
C342
L303
L304
14
32
80
17
R537
C338
SENSOR BOARD
(CONDUCTOR SIDE)
3
R301
R522
1
(11)
R352
R525
1-676-656-
IC306
2
R302
R353
R351
C315
11
1
4
C337
F
C348
5
BLK
MAIN BOARD
CN301
R530
R329
R523
B
Q301
R524
E C
RED
11
R305
M902
(SPINDLE)
R331
M
1-654-693-
A
R306
100
76
1
R538
RED
M902
(SLED)
E
C314
SENSOR BOARD
(COMPONENT SIDE)
14
R308
R536
B
K
IC401
R404
RED
4
R405
SERVO BOARD
M903
(LOADING)
R518
65
C349
1
64
(LIMIT)
IC303
R501
H
1
R502
C336
16
L306
D401
D501
Location
R535
A-15
E-13
R539
+ C318
R355
36
C501
C327
R532
L302
R347
R340
R345
R344
(11)
22
22
R339
R350
R357
Q302
11
R349
R343
LOADING START
EJECT END
R528
R506
+
C346
R341
R348
C321
R336
R527
24
C324
13
C347
C320
R337
25
12
R346
C325
20
1-676-656-
40
R511
C326
05
25
X501
IC302
E-6
K-10
B-13
41
37
1
CN102
24
C330
C328
C331
C329
48
OPTICAL
PICK-UP
BLOCK
(KMS-241C)
C322
Q301
Q302
Q401
+ C319
(CHASSIS)
C E
K
B-11
D-8
K-11
H-8
D-10
B-16
F-8
A-14
H-15
D-11
F-11
B
J
R356
1
IC101
IC301
IC302
IC303
IC304
IC305
IC306
IC401
IC501
IC502
IC503
R516
R505
Ref. No.
R504
C334
I
IC501
R531
C516
L305
• Semiconductor
Location
C335
R503
(CHASSIS)
R526
R529
11
R342
R338
1-675-655-
(11)
MDX-C6400R/C6500R/C6500RX
4-7.
PRINTED WIRING BOARD – SERVO Board (Conductor Side) –
1
2
3
4
5
• See page 21 for Circuit Boards Location.
6
7
8
9
10
11
12
A
(CONDUCTOR SIDE)
C102
R101
R201
R104
B
E
B C E
C
R202
C202
C510
Q402
C101
R403
B
+
R402
R401
C201
SERVO BOARD
Q403
+ C361
C362
+
13
9
5
1
C
R359
C359
IC307
18
22
26
C353
+
C302
C345
C309
14
C344
L301
D
C307
C317
C358
C301
C356
C511
C357
F
R335
R333
+
R332
C506
R334
L501
E
C316
C512
C505
RB302
RB301
+
R534
R533
C515
C351
C350
G
C504
C514
R540
R520
H
R542
R521
C513
C333
R519
I
R510
J
TH501
R512
C503
RB503
K
• Semiconductor
Location
11
05
1-675-655-
23
23
(11)
Ref. No.
Location
IC307
C-10
Q402
Q403
B-4
B-5
MDX-C6400R/C6500R/C6500RX
4-8.
SCHEMATIC DIAGRAM – SERVO Board (1/2) –
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD PLAY
∗ : Impossible to measure
• See page 31 for Waveforms.
• See page 36 for IC Block Diagrams.
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
24
24
MDX-C6400R/C6500R/C6500RX
4-9. SCHEMATIC DIAGRAM – SERVO Board (2/2) –
• See page 31 for Waveforms.
• See page 36 for IC Block Diagram.
(Page
29)
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD PLAY
: Impossible to measure
∗
25
25
MDX-C6400R/C6500R/C6500RX
4-10.
PRINTED WIRING BOARD – MAIN Board (Component Side) – • See page 21 for Circuit Boards Location.
• Semiconductor
Location
Ref. No.
Location
D1
D301
D501
D502
D551
D552
D553
D554
D555
D556
D557
D558
D559
D560
D571
D603
D605
D611
D612
D613
D614
D615
D616
D617
D618
D622
D623
D624
D653
D661
D662
D673
D674
D701
D702
D703
D704
D705
D706
D708
D710
E-9
G-5
I-7
H-7
J-13
K-13
K-13
J-12
K-13
J-12
K-13
J-12
K-13
J-12
B-5
B-4
B-5
B-7
B-7
C-7
C-7
C-7
C-7
C-6
C-6
D-9
C-9
C-9
I-7
D-5
D-5
C-5
C-5
E-5
C-4
B-3
B-2
B-2
B-2
G-7
D-4
IC51
IC90
IC151
IC501
IC652
IC701
I-12
G-11
D-10
I-5
J-3
C-3
Q1
Q111
Q131
Q171
Q181
Q250
Q271
Q281
Q363
Q551
Q571
Q621
Q622
Q633
Q651
Q652
Q661
Q701
Q704
Q705
Q706
G-11
E-12
F-12
B-11
B-11
H-2
C-11
C-11
I-3
J-6
D-5
C-10
C-9
J-2
I-8
I-8
D-5
D-5
G-7
C-4
D-4
26
26
2
3
4
5
6
7
8
BATT
GND
6
5
3
4
MDX-C6400R/C6500R/C6500RX
7
8
ACC
1
ACC
16
GND
15
ANT REM
14
AMP REM
13
FR+
12
RR+
11
ANT REM
BATT
ATT
FR–
RR–
RL–
FL–
10
FL+
9
RL+
FR–
FL–
RL–
RR+
FR+
RL–
• See page 21 for Circuit Boards Location.
FL+
PRINTED WIRING BOARD – MAIN Board (Conductor Side) –
RL+
4-11.
2
1
(FRONT VIEW)
• Semiconductor
Location
(Page 32)
(Page 22)
27
27
Ref. No.
Location
D2
D90
D91
D92
D131
D302
D361
D362
D561
D562
D563
D564
D601
D602
D604
D621
D631
D671
D672
D675
D676
D677
D709
E-7
H-11
H-11
G-11
F-12
G-7
I-2
G-2
K-11
K-11
K-13
K-12
C-3
B-4
A-5
B-10
J-2
C-5
C-5
I-4
I-4
I-4
G-5
IC611
IC671
A-7
F-1
Q90
Q121
Q361
Q362
Q631
G-11
E-12
H-1
G-1
J-2
MDX-C6400R/C6500R/C6500RX
4-12.
SCHEMATIC DIAGRAM – MAIN Board (1/3) –
• See page 31 for Waveform.
• See page 36 for IC Block Diagrams.
(Page 30)
(Page 29)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : MW
[
] : LW
28
28
MDX-C6400R/C6500R/C6500RX
4-13.
SCHEMATIC DIAGRAM – MAIN Board (2/3) –
• See page 31 for Waveforms.
(Page 28)
(Page
25)
(Page
30)
29
29
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : MW
[
] : LW
〈〈
〉〉 : MD PLAY
: Impossible to measure
∗
MDX-C6400R/C6500R/C6500RX
4-14.
SCHEMATIC DIAGRAM – MAIN Board (3/3) –
• See page 36 for IC Block Diagrams.
(Page
28)
(Page
33)
(Page
29)
• Voltages are dc with respect to ground under no-signal
(detuned) conditions.
no mark : FM
〈〈
〉〉 : MD PLAY
30
30
MDX-C6400R/C6500R/C6500RX
• Waveforms
– SERVO Board –
1 IC101 1 (XTI) (MD Play Mode)
6 IC301 wh (XBCK) (MD Play Mode)
4.4 Vp-p
qa IC302 1, 2, r;, rh (I, J, AGCI, RFO)
(MD Play Mode)
4.6 Vp-p
– MAIN Board –
– KEY Board –
1 IC51 4 (OSCD)
1 IC901 y; (OSC)
354 ns
88 ns
2 IC101 4 (LRCK) (MD Play Mode)
3.8 Vp-p
22.7 µs
5.4 Vp-p
4.1 Vp-p
30.5 µs
44.3 ns
8 IC301 tg (RFI), IC302 ek (RF)
(MD Play Mode)
3.4 Vp-p
2 IC501 ud (X1A)
qs IC304 1, 2 (MD Play Mode)
4.4 Vp-p
88 ns
3 IC101 6 (BCK) (MD Play Mode)
3 IC501 od (X1A)
qd IC304 3 (MD Play Mode)
3.4 Vp-p
Apporx.
1.5 Vp-p
5.6 Vp-p
44.3 ns
354 ns
4 IC301 qh (OSCI) (MD Play Mode)
9 IC301 yg (FE), IC302 ef (FE)
(MD Play Mode)
4.6 Vp-p
272 ns
qf IC304 7 (MD Play Mode)
4.4 Vp-p
Approx.
0.5 Vp-p
44.3 ns
44.3 ns
5 IC301 wg (LRCK) (MD Play Mode)
0 IC301 uf (TE), IC302 wh (TE)
(MD Play Mode)
qg IC501 ea (EXTAL)
4.4 Vp-p
3.7 Vp-p
Approx.
2 Vp-p
22.7 µs
26.4 µs
231 ns
7 IC301 wj (FS256) (MD Play Mode)
2.6 Vp-p
5 Vp-p
Apporx.
0.6 Vp-p
101 ns
31
31
MDX-C6400R/C6500R/C6500RX
4-15.
PRINTED WIRING BOARD – SUB Board –
• See page 21 for Circuit Boards Location.
(Page 27)
(Page 34)
32
32
4-16.
MDX-C6400R/C6500R/C6500RX
SCHEMATIC DIAGRAM – SUB Board –
(Page 30)
(Page 35)
33
33
MDX-C6400R/C6500R/C6500RX
4-17.
PRINTED WIRING BOARD – KEY Board –
• See page 21 for Circuit Boards Location.
• Semiconductor
Location
Ref. No.
Location
IC951
C-5
LED901
LED902
LED903
LED904
LED910
LED911
LED912
LED913
LED914
LED915
A-2
C-2
C-3
A-3
B-12
B-12
A-12
A-5
B-5
B-5
• Semiconductor
Location
Ref. No.
Location
D901
D902
D903
D904
D951
D952
A-11
B-10
B-10
B-10
C-4
B-6
IC901
B-8
(Page 32)
34
34
4-18.
SCHEMATIC DIAGRAM – KEY Board –
MDX-C6400R/C6500R/C6500RX
• See page 31 for Waveform.
(Page
33)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
35
35
MDX-C6400R/C6500R/C6500RX
CLK
CONTROL
XTI 1
DGND 2
–
+
RFA1
I
17 DM1
J
16 DM0
1
–1
–
–2
–
2
LOWPASS
FILTER
LOWPASS
FILTER
AGND 10
CMOS
AMP
CMOS
AMP
COMPO
AGCI
RF AGC
RF
PEAK
39
38
37
RF AGC
+
–
EQ
USRC
RFA3
HLPT
–1
EQ
14 FORMAT
13 D/C_L
VC
3
–2
IVR
BOTTOM
TEMP
PBSW
WBL
35 ABCD
34 FE
–
–
–
–
AA
36 BOTM
PBH
–1
GRVA
+
–
4
WBL
PEAK
11 VCC
A
P-P
3T
PTGR
GRV
12 VOUTL
AUX
SW
PEAK3T
3T
–2
–
1
–
–2
–
+
VOUTR 9
40
OFST
CVB
D/C_R 8
41
DET
15 RSTB
BCKIN 6
ZERO 7
43 42
BPF3T
NOISE SHAPER
5 LEVEL
DAC
44
USROP
RFA2
DIN 5
5 LEVEL
DAC
COMPP
45
ADDC
46
OPO
OPN
47
18 MUTE
MODE
CONTROL
DIGITAL
FILTER
LRCIN 4
48
20 XTO
19 CLKO
INPUT
INTERFACE
VDD 3
RFO
PCM1718E/2K
MORFI
CXA2523AR
+
–
IC101
IC302
MORFO
• IC Block Diagrams
– SERVO Board –
33 AUX
BPFC
ABCDA
32 ADFG
B
IVR
100 99 98 97 96 95
94 93
DCHG
APC
ADFG
F0CNT
XLRF
CKRF
DTRF
APCREF
LDDR
TRDR
TFDR
DVDD
FFDR
FRDR
FS4
SRDR
SFDR
SPRD
SPFD
FGIN
TEST1
TEST2
TEST3
DVSS
+
–
5
CXD2652AR
EFMO
IC301
C
+
–
6
92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
31 ADAGC
BB
IVR
+
+
–
–
30 ADIN
FEA
CC
DET
EACH
BLOCK
74 TE
IVR
E
70 ADRT
IVR
SENS 9
A/D
CONVERTER
F
IVR
65 FE
ANALOG
MUX
64 ABCD
XRST 10
IV
APCREF 12
PLL
DIGITAL
AUDIO
I/F
DVSS 20
55 RFI
COMP
SAMPLING
RATE
CONVERTER
54 BIAS
53 AVDD
DIN 21
52 ASYI
DOUT 22
51 ASYO
ADDT 23
ATRAC
ENCODER/DECODER
DADT 24
LRCK 25
ADDRESS/DATA BUS A00 - A11, D0 - D3
50
MVCI
D3
D2
D0
D1
XWE
XRAS
A09
XCAS
XOE
DVSS
A11
A08
A07
A06
A05
A04
A10
A01
A00
A02
A03
DVDD
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
36
36
14
15
16
17
18
19
20
21
22 23
24
SWDT
SCLK
XLAT
XSTBY
F0CNT
VREF
EQADJ
VCC
EACH
BLOCK
13
TEMPR
57 PDO
56 AVSS
NC 19
VREF
SCRI - PARA
DECODE
APC 11
58 PCO
TX 15
FS256
25 WBLADJ
VI CONV
BGR
COMMAND
–
+ –
59 FILI
OSCI 16
XBCK
3T
EQ
AUXSW
+
26 TE
TEA
WBL
FF'
FBAL
60 FILO
EFM/ACIRC
ENCODER/
DECODER
SHOCK RESISTANT
MEMORY CONTROLLER
XINT 14
26 27 28
+
–
PD 10
61 CLTV
CLOCK
GENERATOR
–2
TG
62 PEAK
SUBCODE
PROCESSOR
RECP 13
XTSL 18
FF
GSW
63 BOTM
OSCO 17
+
–
9
28 SE
SEA
27 CSLED
ESW
66 AUX1
TG
–1
TESW
EBAL
67 VC
SERVO
DSP
–2
TEMPI
CPU I/F
EE'
–1
PTGR
–
+
–
+
EFB
68 ADIO
EACH
BLOCK
SRDT 8
+
–
EE
69 AVDD
SCLK 6
SQSY 11
+
–
8
29 ADFM
DD
WBL
71 ADRB
SWDT 5
ADIP
AGC
WBL
ATA
72 AVSS
ADIP
DECODER
DQSY 12
+
–
7
73 SE
MNT3 4
XLAT 7
D
–
–
+
+
3TADJ
MONITOR
CONTROL
75 AUX2
GND
MNT2 3
PWM
GENERATOR
SPINDLE
SERVO
MNT0 1
MNT1 2
AUTO
SEQUENCER
BPF22
CAPA+
IN2R
IN2F
VM2
OUT2F
PGND2
OUT2R
VM12
OUT1R
PGND1
OUT1F
VM1
IN1F
IN1R
VDD
BH6511FS-E2
CAPA–
IC303
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
INTERFACE
PREDRIVE
PREDRIVE
PREDRIVE
7
8
9
IN4F
VM4
OUT4F
PGND4
OUT4R
VM34
10
11
12
13
14
15
16
PSB
6
IN3R
5
PSB
IN3F
4
INTERFACE
VM3
3
AMP
OUT3F
2
IN4R
AMP
VDD
PGND3
AMP
AMP
VG
GND
IC305
AMP
PREDRIVE
INTERFACE
1
AMP
OUT3R
CHARGE
PUMP.
OSC
AMP
AMP
INTERFACE
BA6287F
OUT1 1
8 GND
VM 2
7 OUT2
DRIVER
DRIVER
TSD
VCC 3
6 VREF
CONTROL LOGIC
POWER
SAVE
FIN 4
IC307
5 RIN
MN41V4400TT-08S
TIMING
GENERATOR
6
7
8
A0 9
A1 10
A2 11
A3 12
COLUMN
NC
NC
NC
25 DQ4
24 DQ3
ADDRESS BUFFERS
1
2
3
4
5
ROW
DQ1
DQ2
WE
RAS
A9
26 VSS
TIMING
GENERATOR
COLUMN
DECODERS
INTERNAL
ADDRESS
COUNTER
REFRESH
CONTROL
CLOCK
SENSE
AMPLIFIERS
ROW
DECODERS
WORD
DRIVERS
MEMORY
CELLS
I/O
SELECTOR
INPUT
BUFFERS
WRITE
CLOCK
GENERATOR
OUTPUT
BUFFERS
23 CAS
22 OE
21 NC
20 NC
19 NC
18
17
16
15
14
A8
A7
A6
A5
A4
DATA BUS
VCC 13
37
– MAIN Board –
LVIN
CIN
SCOUT
VREF
MPX
VSSA
VDDA
AFIN
MAD
PSWN
IC51 SAA6588T/V2-118
20
19
18
17
16
15
14
13
12 11
PAUSE
DETECTOR
POWER SUPPLY
& RESET
MULTI
PATH
DETECTOR
57kHz
8th ORDER
BAND-PASS FILTER
CLOCKED
COMPARATOR
SIGNAL QUALITY
DECODER
4
5
4
CLOCK
RDS/RDBS
DEMODULATOR
CLOCK
RDS/RDBS
DECODER
INTERFACE
REGISTER
DATA
DATA
OSCILLATOR
& CLOCK
IC671
10
SCL
SDA
OSCI
9
8
7
6
DAVN
5
VSSD
4
IIC BUS SLAVE
TRANSCEIVER
VDDD
3
OSCO
MRO
MPTH
1 2
TCON
TEST
CONTROL
BA4908-V3
REGULATOR
OVER VOLTAGE
PROTECT
AMP
VCC
10
11
12
GND
VDD5.6V
9
TUNER8.7V
NC
38
8
TUNER5.6V
7
ANT
6
COM8.7V
5
TUNER8.7 ANT SW
TUNER5.6 SW
STB
+
–
2 3 4
+
–
1
+
–
–
+
OUTLF
OUTLR
OUTRF
OUTRR
OUTSWL
OUTSWR
OUTSSL
OUTSSR
TDA7402TR
ACINLR
ACINRF
ACINRR
IC151
33 32 31
30
29
28
27
26
25
24 23
MIXER
MONO- MONOFADER FADER
ACINLF 34
SWINR 35
SWINL 36
ACIN
ACOUTR 37
ACOUTL 38
MAIN
MONO- MONOFADER FADER
MONO- MONOFADER FADER
FRONT
OUTPUT
SELECTOR
SUBWOOFER
+PHASE
CONTROL
REAR
SW
SECOND
CREF 39
22 VDD
IIC-BUS
LP
VOICE
BANDPASS
HP
21 SCL
20 SDA
BASS
SUPPLY
TREBLE
DIGITAL CONTROL
HIGH-CUT
VOLUME
SOFTMUTE
COMPANDER
19 GND
18 SM
S&H
PULSE
FORMER
25kHz
LP
QUAL
17 QUAL
LOUDNESS
LOUDNESS
+
IN-GAIN
IN-GAIN
+AUTO ZERO
MUTE
MULTIPATH
DETECTOR
DEMODULATOR
+STEREO ADJUST
+STEREO BLAND
MUX 40
BEEP
D/A
CONVERTER
PILOT
CANCELATION
16 MPOUT
15 MPIN
14 LEVEL
PIL DET
MAIN SOURCE
SELECTOR
IC701
PLL
MAIN
INPUT
MULTIPLEXER
MAIN
CH0
AUX
AM
1 2
3 4 5 6
7 8 9 10
11
FD2L+
FD2L–
FD2R+
FD2R–
AM
AM/FM
NOISE BLANKER
12 AMIF
BA8270F-E2
BUS ON
SWITCH
RST 2
RESET
SWITCH
BATT 3
BATTERY
SWITCH
GND 7
13 MPX
PHONO
BUS ON 1
CLK 4
VREF 5
DATA 6
80kHz
LP
FM
FD1L+
FD1L–
FD1R+
FD1R–
MD2 43
MD2G 44
SECOND SOURCE
SELECTOR
SEL
SER
MD1 41
MD1G 42
MIXING
SELECTOR
14 VCC
13
12
11
10
RST
BUS ON
CLK IN
BU IN
9 DATA IN
8 DATA OUT
39
4-19.
IC PIN FUNCTION DESCRIPTION
• SERVO BOARD IC301 CXD2652AR
(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M BIT D-RAM)
Pin No.
Pin Name
I/O
Description
1
MNT0
O
Focus OK signal output to the MD mechanism controller (IC501)
“H” is output when focus is on (“L”: NG)
2
MNT1
O
Track jump detection signal output to the MD mechanism controller (IC501)
3
MNT2
O
Busy monitor signal output to the MD mechanism controller (IC501)
4
MNT3
O
Spindle servo lock status monitor signal output to the MD mechanism controller (IC501)
5
SWDT
I
Writing serial data signal input from the MD mechanism controller (IC501)
6
SCLK
I
Serial data transfer clock signal input from the MD mechanism controller (IC501)
7
XLAT
I
Serial data latch pulse signal input from the MD mechanism controller (IC501)
8
SRDT
O (3)
Reading serial data signal output to the MD mechanism controller (IC501)
9
SENS
O (3)
Internal status (SENSE) output to the MD mechanism controller (IC501)
10
XRST
I
Reset signal input from the MD mechanism controller (IC501) “L”: reset
11
SQSY
O
Subcode Q sync (SCOR) output to the MD mechanism controller (IC501)
“L” is output every 13.3 msec Almost all, “H” is output
12
DQSY
O
Digital In U-bit CD format subcode Q sync (SCOR) output terminal
“L” is output every 13.3 msec Almost all, “H” is output Not used (open)
13
RECP
I
Laser power selection signal input terminal
“L”: playback mode, “H”: recording mode (fixed at “L” in this set)
14
XINT
O
Interrupt status output to the MD mechanism controller (IC501)
15
TX
I
Recording data output enable signal input terminal
Writing data transmission timing input (Also serves as the magnetic head on/off output)
Not used (fixed at “L”)
16
OSCI
I
System clock signal (512Fs=22.5792 MHz) input from the oscillator circuit
17
OSCO
O
System clock signal (512Fs=22.5792 MHz) output terminal Not used (open)
18
XTSL
I
Input terminal for the system clock frequency setting
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)
19
RVDD
—
Power supply terminal (+3.3V) (digital system)
20
RVSS
—
Ground terminal (digital system)
21
DIN
I
Digital audio signal input terminal when recording mode Not used (fixed at “L”)
22
DOUT
O
Digital audio signal output terminal when playback mode Not used (open)
23
ADDT
I
Recording data input terminal Not used (fixed at “L”)
24
DADT
O
Playback data output to the PCM1718E (IC101)
25
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the PCM1718E (IC101)
26
XBCK
O
Bit clock signal (2.8224 MHz) output to the PCM1718E (IC101)
27
FS256
O
Clock signal (11.2896 MHz) output to the PCM1718E (IC101)
28
DVDD
—
Power supply terminal (+3.3V) (digital system)
29 to 32
A03 to A00
O
Address signal output to the D-RAM (IC307)
33
A10
O
Address signal output to the external D-RAM Not used (open)
34 to 38
A04 to A08
O
Address signal output to the D-RAM (IC307)
39
A11
O
Address signal output to the external D-RAM Not used (open)
40
DVSS
—
Ground terminal (digital system)
41
XOE
O
Output enable signal output to the D-RAM (IC307) “L” active
42
XCAS
O
Column address strobe signal output to the D-RAM (IC307) “L” active
43
A09
O
Address signal output to the D-RAM (IC307)
44
XRAS
O
Row address strobe signal output to the D-RAM (IC307) “L” active
45
XWE
O
Write enable signal output to the D-RAM (IC307) “L” active
40
Pin No.
Pin Name
I/O
Description
46
D1
I/O
47
D0
I/O
48
D2
I/O
49
D3
I/O
50
MVCI
I
Digital in PLL oscillation input from the external VCO Not used (fixed at “L”)
51
ASYO
O
Playback EFM full-swing output terminal
52
ASYI
I (A)
53
AVDD
—
54
BIAS
I (A)
55
RFI
I (A)
56
AVSS
—
57
PDO
O (3)
Phase comparison output for clock playback analog PLL of the playback EFM Not used (open)
58
PCO
O (3)
Phase comparison output for master clock of the recording/playback EFM master PLL
59
FILI
I (A)
Filter input for master clock of the recording/playback master PLL
60
FILO
O (A) Filter output for master clock of the recording/playback master PLL
61
CLTV
I (A)
Internal VCO control voltage input of the recording/playback master PLL
62
PEAK
I (A)
Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC302)
63
BOTM
I (A)
Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC302)
64
ABCD
I (A)
Light amount signal (ABCD) input from the CXA2523AR (IC302)
65
FE
I (A)
Focus error signal input from the CXA2523AR (IC302)
Two-way data bus with the D-RAM (IC307)
Playback EFM asymmetry comparator voltage input terminal
Power supply terminal (+3.3V) (analog system)
Playback EFM asymmetry circuit constant current input terminal
Playback EFM RF signal input from the CXA2523AR (IC302)
Ground terminal (analog system)
66
AUX1
I (A)
Auxiliary signal (I3 signal/temperature signal) input terminal Not used (fixed at “H”)
67
VC
I (A)
Middle point voltage (+1.65V) input from the CXA2523AR (IC302)
68
ADIO
69
AVDD
—
70
ADRT
I (A)
A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
71
ADRB
I (A)
A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
72
AVSS
—
73
SE
I (A)
Sled error signal input from the CXA2523AR (IC302)
74
TE
I (A)
Tracking error signal input from the CXA2523AR (IC302)
75
AUX2
I (A)
Auxiliary signal input terminal Light amount signal input from the CXA2523AR (IC302)
76
DCHG
I (A)
Connected to the +3.3V power supply
77
APC
I (A)
Error signal input for the laser automatic power control Not used (fixed at “L”)
78
ADFG
I
ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC302)
79
F0CNT
O
Filter f0 control signal output terminal Not used (open)
O (A) Monitor output of the A/D converter input signal Not used (open)
Power supply terminal (+3.3V) (analog system)
Ground terminal (analog system)
80
XLRF
O
Serial data latch pulse signal output terminal Not used (open)
81
CKRF
O
Serial data transfer clock signal output terminal Not used (open)
82
DTRF
O
Writing serial data output terminal Not used (open)
83
APCREF
O
Control signal output to the reference voltage generator circuit for the laser automatic power
control
84
LDDR
O
PWM signal output for the laser automatic power control Not used (open)
85
TRDR
O
Tracking servo drive PWM signal (–) output to the BH6511FS (IC303)
86
TFDR
O
Tracking servo drive PWM signal (+) output to the BH6511FS (IC303)
87
DVDD
—
Power supply terminal (+3.3V) (digital system)
88
FFDR
O
Focus servo drive PWM signal (+) output to the BH6511FS (IC303)
41
Pin No.
Pin Name
I/O
Description
89
FRDR
O
Focus servo drive PWM signal (–) output to the BH6511FS (IC303)
90
FS4
O
Clock signal (176.4 kHz) output terminal (X’tal system)
91
SRDR
O
Sled servo drive PWM signal (–) output to the BH6511FS (IC303)
92
SFDR
O
Sled servo drive PWM signal (+) output to the BH6511FS (IC303)
93
SPRD
O
Spindle servo drive PWM signal (–) output to the BH6511FS (IC303)
94
Not used (open)
SPFD
O
Spindle servo drive PWM signal (+) output to the BH6511FS (IC303)
95
FGIN
I
Not used (fixed at “L”)
96
TEST1
I
97
TEST2
I
98
TEST3
I
99
DVSS
—
Ground terminal (digital system)
100
EFMO
O
EFM signal output terminal when recording mode
Input terminal for the test (fixed at “L”)
Not used (open)
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
42
• SERVO BOARD IC302 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No.
Pin Name
I/O
Description
1
I
I
I-V converted RF signal I input from the optical pick-up block detector
2
J
I
I-V converted RF signal J input from the optical pick-up block detector
3
VC
O
Middle point voltage (+1.65V) generation output terminal
4 to 9
A to F
I
Signal input from the optical pick-up detector
10
PD
I
Light amount monitor input from the optical pick-up block laser diode
11
APC
O
Laser amplifier output terminal to the automatic power control circuit
12
APCREF
I
Reference voltage input terminal for setting laser power
13
GND
—
Ground terminal
14
TEMPI
I
Connected to the temperature sensor Not used (open)
15
TEMPR
O
Output terminal for a temperature sensor reference voltage Not used (open)
16
SWDT
I
Writing serial data input from the MD mechanism controller (IC501)
17
SCLK
I
Serial data transfer clock signal input from the MD mechanism controller (IC501)
18
XLAT
I
Serial data latch pulse signal input from the MD mechanism controller (IC501)
19
XSTBY
I
Standby signal input terminal “L”: standby (fixed at “H” in this set)
20
F0CNT
I
Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input
terminal
21
VREF
O
Reference voltage output terminal Not used (open)
22
EQADJ
I
Center frequency setting terminal for the internal circuit (EQ)
23
3TADJ
I
Center frequency setting terminal for the internal circuit (BPF3T)
24
VCC
—
25
WBLADJ
I
Center frequency setting terminal for the internal circuit (BPF22)
26
TE
O
Tracking error signal output to the CXD2652AR (IC301)
27
CSLED
I
Connected to the external capacitor for low-pass filter of the sled error signal
28
SE
O
Sled error signal output to the CXD2652AR (IC301)
29
ADFM
O
FM signal output of the ADIP
30
ADIN
I
Receives a ADIP FM signal in AC coupling
31
ADAGC
I
Connected to the external capacitor for ADIP AGC
32
ADFG
O
ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2652AR (IC301)
Power supply terminal (+3.3V)
33
AUX
O
Auxiliary signal (I3 signal/temperature signal) output terminal Not used (open)
34
FE
O
Focus error signal output to the CXD2652AR (IC301)
35
ABCD
O
Light amount signal (ABCD) output to the CXD2652AR (IC301)
36
BOTM
O
Light amount signal (RF/ABCD) bottom hold output to the CXD2652AR (IC301)
37
PEAK
O
Light amount signal (RF/ABCD) peak hold output to the CXD2652AR (IC301)
38
RF
O
Playback EFM RF signal output to the CXD2652AR (IC301)
39
RFAGC
I
Connected to the external capacitor for RF auto gain control circuit
40
AGCI
I
Receives a RF signal in AC coupling
41
COMPO
O
User comparator output terminal Not used (open)
42
COMPP
I
User comparator input terminal Not used (fixed at “L”)
43
ADDC
I
Connected to the external capacitor for cutting the low band of the ADIP amplifier
44
OPO
O
User operational amplifier output terminal Not used (open)
45
OPN
I
User operational amplifier inversion input terminal Not used (fixed at “L”)
46
RFO
O
RF signal output terminal
47
MORFI
I
Receives a MO RF signal in AC coupling
48
MORFO
O
MO RF signal output terminal
43
• SERVO BOARD IC501 CXP84340-217Q (MD MECHANISM CONTROLLER)
Pin No.
Pin Name
I/O
1 to 5
TIN3 to TIN7
I/O
Input of the 4×8 matrix test keys (“L” is always output, except in test mode)
6
LOAD
O
Loading motor control signal output to the motor driver (IC305) “H” active *1
7
EJECT
O
Loading motor control signal output to the motor driver (IC305) “H” active *1
8, 9
NCO
O
Not used (open)
10
MDMON
O
Power supply on/off control signal output of the MD mechanism deck section main power supply
and loading motor drive (IC305) power supply “H”: power on
11
E-SW
I
Inputs the disc loading completion detect switch detection signal
“L”: When completed of the disc loading operation
12
AG-OK
O
Output of aging status in test mode “L”: under aging, “H”: aging completed Not used (open)
13
ADJ-OK
O
Output of status when aging completed in test mode “L”: aging NG, “H”: aging OK
Not used (open)
14 to 17
NCO
O
Not used (open)
18
DFCTSEL
I
Select whether defect function is used for the CXD2652AR (IC301)
“L”: used this function , “H”: not used this function (fixed at “H” in this set)
19
DPLLSEL
I
Select whether digital PLL function is used for the CXD2652AR (IC301)
“L”: used this function , “H”: not used this function (fixed at “H” in this set)
20
EMPHSEL
I
Select whether emphasis signal output from pin or unilink data
“L”: outputs from both pin and unilink data, “H”: output from pin only (fixed at “H” in this set)
21
LOCK
O
Mini-disc lock detection signal output to the master controller (IC501) “H”: lock
22
NCO
O
Not used (open)
23
2M/4M
I
Select whether D-RAM capacitance 2M bit or 4M bit “L”: 4M bit (external D-RAM) , “H”: 2M
bit (internal D-RAM of CXD2652AR) (fixed at “L” in this set)
24, 25
NCO
O
Not used (open)
26
MNT0
I
Focus OK signal input from the CXD2652AR (IC301)
“H” is input when focus is on (“L”: NG)
27
MNT1
I
Track jump detection signal input from the CXD2652AR (IC301)
28
MNT2
I
Busy monitor signal input from the CXD2652AR (IC301)
29
MNT3
I
Spindle servo lock status monitor signal input from the CXD2652AR (IC301)
30
RESET
I
System reset signal input from the master controller (IC501), reset signal generator (IC652) and
reset switch (SW503) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
O
Main system clock output terminal (10 MHz)
32
XTAL
I
Main system clock input terminal (10 MHz)
33
VSS
—
34
TX
O
Sub system clock output terminal (32.768 kHz) Not used (open)
35
TEX
I
Sub system clock input terminal (32.768 kHz) Not used (fixed at “L”)
36
AVSS
—
37
AVREF
I
Reference voltage input terminal (+5V) (for A/D converter)
38
INIT
I
Initial reset signal input terminal (A/D input) (fixed at “H”)
39
TEMP
I
Temperature sensor (TH501) input terminal (A/D input)
40
ACNT
I
Select the number of load/eject aging times (A/D input)
0H – 54H (30 times), 55H – OA9H (20 times), OAAH – OFFH (10 times)
41
DO-SEL
I
Select the digital output bits (A/D input)
42
EE-CS
O
Chip select signal output to the external EEPROM device Not used (open)
43
EE-CKO
O
Serial data transfer clock signal output to the external EEPROM device Not used (open)
44
EE-SIO
I/O
Two way data bus with the external EEPROM device Not used (open)
45
MD-SO
O
Writing serial data signal output to the CXD2652AR (IC301) and CXA2523AR (IC302)
46
LINKOFF
O
Unilink on/off control signal output for the SONY bus “L”: link on, “H”: link off
44
Description
Not used (open)
Ground terminal
Ground terminal (for A/D converter)
Pin No.
Pin Name
I/O
Description
47
UNIREQ
O
Data request signal output terminal (for SONY bus) “H”: request on
48
UNICKIO
I/O
Serial clock signal input from the master controller (IC501) or serial clock signal output to the
SONY bus interface (IC701) and master controller (IC501) (for SONY bus)
49
UNISI
I
Serial data input from the SONY bus interface (IC701)
50
UNISO
O
Serial data output to the SONY bus interface (IC701)
51
MD-CKO
O
Serial data transfer clock signal output to the CXD2652AR (IC301) and CXA2523AR (IC302)
52
MD-SI
I
Reading serial data signal input from the CXD2652AR (IC301)
53
NCO
O
Not used (open)
54
SENS
I
Internal status (SENSE) input from the CXD2652AR (IC301)
55
CC-XINT
I
Interrupt status input from the CXD2652AR (IC301)
56
LIMIT-IN
I
Detection input from the sled limit-in detect switch
The optical pick-up is inner position when “L”
57
EJT-KEY
I
Eject request signal input terminal “L”: eject on
58
ERROR-PWM
O
PWM error monitor output terminal (C1and ATER is output when test mode)
Not used (open)
Not used (fixed at “H”)
Not used (open)
59
MD-RST
O
Reset signal output to the PCM1718E (IC101), CXD2652AR (IC301) and BH6511FS (IC303)
“L”: reset
60
BU-IN
I
Battery detect signal input from the SONY bus interface (IC600) and battery check circuit
“H”: battery on
61
BUS-ON
I
SONY bus on/off control signal input from the master controller (IC700) “L”: bus on
62
SQSY
I
Subcode Q sync (SCOR) input from the CXD2652AR (IC301)
“L” is input every 13.3 msec Almost all, “H” is input
63
C-SW
I
Inputs the disc loading start or disc eject completion detect switch detection signal
“L”: When start or eject completed of the disc loading operation
64
MD-LAT
O
Serial data latch pulse signal output to the CXD2652AR (IC301) and CXA2523AR (IC302)
65
MD-ON
O
Power supply on/off control signal output of the MD mechanism deck section main power supply
“H”: power on
66
DEEMP
O
Emphasis on/off control signal output to the PCM1718E (IC101) “H”: emphasis on
67
A-MUTE
O
Audio muting on/off control signal output terminal
68
NCO
O
Not used (open)
69
TSTCKO
O
Output of clock signal for the test mode display
70
TSTSO
O
Output of data for the test mode display
71
TSTMOD
I
Setting terminal for the test mode “L”: test mode, “H”: normal mode
72
VCC
—
73
NIL
I
Not used (fixed at “H”)
74 to 77
TOUT0 to TOUT3
O
Output of the 4×8 matrix test keys
78 to 80
TIN0 to TIN2
I/O
Input of the 4×8 matrix test keys (“L” is always output, except in test mode)
Not used (open)
Not used (open)
Power supply terminal (+5V)
Not used (open)
Not used (open)
*1 Loading motor (M903) control
Operation
Terminal
IN
OUT
BRAKE
STOP
LOAD (pin 6)
“H”
“L”
“H”
“L”
EJECT (pin 7)
“L”
“H”
“H”
“L”
45
• MAIN BOARD IC501 MB90574PMT-G-266-BND (MASTER CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
TUNON
O
Tuner system power supply on/off control signal output to the BA4908 (IC671)
“H”: tuner power on
2
ANT CUT
O
Tuner system power supply on/off control signal output terminal “H”: tuner power on
Not used (open)
3
BUSON
O
Bus on/off control signal output to the MD mechanism controller (IC501) and SONY bus
interface (IC701) “L”: bus on
4 to 6
NCO
O
Not used (open)
7
ILLON
O
Power on/off control signal output of the illumination LED and liquid crystal display driver
(IC901) “H”: power on
8
VCC
—
Power supply terminal (+5V)
9
E2P SIO
I/O
Two-way data E2P bus with the FM/AM tuner unit (TU1)
10
E2P CKO
O
E2P bus clock signal output to the FM/AM tuner unit (TU1)
11
SYSRST
O
System reset signal output to the MD mechanism controller (IC501) and SONY bus interface
(IC701) “L”: reset
12
DOORSW
I
Front panel open/close detection signal input terminal
“L” is input when the front panel is closed
13
LCDSO
O
Serial data output to the liquid crystal display driver (IC901)
14
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC901)
15
Chip enable signal output to the liquid crystal display driver (IC901) “H” active
LCDCE
O
16
BEEP
O
Beep sound drive signal output to the power amplifier (IC611)
17
UNISI
I
Serial data input from the SONY bus interface (IC701)
18
UNISO
O
Serial data output to the SONY bus interface (IC701)
19
UNICKO
O
Serial clock signal output to the MD mechanism controller (IC501) and SONY bus interface
(IC701)
20
UNICKI
I
Serial clock signal input from the MD mechanism controller (IC501) (for SONY bus)
21
CD MD
I
Setting terminal for the internal mechanism CD or MD
“L”: CD, “H”: MD (fixed at “H” in this set)
22
FLASHW
I
Internal flash memory data write mode detection signal input terminal “L”: data write mode
Not used
23
NCO
O
Not used (open)
24
SIRCS
I
Sircs remote control signal input from the remote control receiver (IC951)
25 to 28
NCO
O
Not used (open)
29
DOORIND
O
LED drive signal output of the MD disc slot illumination and Z indicator (LED810, LSW810)
“H”: LED on “H” is output to turn on LED when front panel is opened
30, 31
NCO
O
Not used (open)
32
NS MASK
O
Discharge control signal output for the noise detection circuit “H”: discharge
33
VSS
—
Ground terminal
34
C
—
Connected to coupling capacitor for the power supply
35
AD ON
O
A/D converter power control signal output terminal
When the KEYACK (pin uh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
36
REIN0
I
37
REIN1
I
38
DVCC
—
Power supply terminal (+5V) (for D/A converter)
Dial pulse input of the rotary encoder (RE901)
(for VOLUME/BASS/TREBLE/BALANCE/FADER control)
39
DVSS
—
Ground terminal (for D/A converter)
40, 41
NCO
O
Not used (open)
42
AVCC
—
Power supply terminal (+5V) (for analog system)
46
Pin No.
Pin Name
I/O
Description
43
AVRH
I
Reference voltage (+5V) input terminal (for A/D converter)
44
AVRL
I
Reference voltage (0V) input terminal (for A/D converter)
45
AVSS
—
46
KEYIN0
I
Key input terminal (A/D input) (LSW901 to LSW908, S901 to S904)
OFF, SOURCE, SOUND, MENU, PTY DSPL, LIST, ENTER, MODE,
SEEK/AMS - . m + > M, DISC/PRST +, PRST/DISC - keys input
47
KEYIN1
I
Key input terminal (A/D input) (LSW810, LSW909 to LSW917)
Z, D-BASS, TA, FA, 6 to 3 SHUF 2, REP 1 keys input
48
RCIN0
I
Rotary remote commander key input terminal (A/D input)
Ground terminal (for analog system)
49
DSTSEL
I
Destination setting terminal (fixed at “L” in this set)
50
QUALITY
I
Noise level detection signal input at SEEK mode (A/D input)
51
FMAGC
I
FM AGC detection signal input from the FM/AM tuner unit (TU1) (A/D input)
52
MPTH
I
Multi-path detection signal input from the RDS decoder (IC51) (A/D input)
53
VSM
I
FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)
(A/D input)
54
VCC
—
55
RAMBU
I
Internal RAM reset detection signal input terminal
Input terminal to check that RAM data are not destroyed due to low voltage
This checking is made within 100 msec after reset Not used (fixed at “H”)
56
TUNATT
O
Muting on/off control signal output of the FM/AM tuner signal “H”: muting on
57
VOLATT
O
Pre amplifier muting on/off control signal output to the electrical volume (IC151)
“L”: muting on
58
ATT
O
Audio line muting on/off control signal output terminal “H”: muting on
59
AMPON
O
Standby on/off control signal output to the power amplifier (IC611)
“L”: standby mode, “H”: ampifier on
60
AMPATT
O
Power amplifier muting on/off control signal output to the power amplifier (IC611)
“L”: muting on
61
COLSW
I
Setting terminal for the illumination color “L”: 2 color, “H”: 1 color (fixed at “H” in this set)
62
COLSEL
I
Setting terminal for the illumination color “L”: amber, “H”: green (fixed at “L” in this set)
63
VSS
—
64
DAVN
I
Data transmit completed detection signal input from the RDS decoder (IC51) “H” active
65
FILE
I
Setting terminal for the custom file “L”: unavailable, “H”: available (fixed at “H” in this set)
66
TEXT
I
Setting terminal for the CD text “L”: unavailable, “H”: available (fixed at “H” in this set)
67
NOSESW
I
Front panel block remove/attach detection signal input from the nose detection switch (SW504)
“L”: front panel is attached
68, 69
NCO
O
Not used (open)
70
I2C SIO
I/O
Two-way data I2C bus with the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical
volume (IC151)
71
I2C CKO
O
I2C bus clock signal output to the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical
volume (IC151)
72
NCO
O
Not used (open)
73
X1A
O
Sub system clock output terminal (32.768 kHz)
74
X0A
I
Sub system clock input terminal (32.768 kHz)
75
NCO
O
Not used (open)
76
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
77
BUIN
I
Battery detection signal input from the SONY bus interface (IC701) and battery detect circuit
“L” is input at low voltage
Power supply terminal (+5V)
Ground terminal
47
Pin No.
Pin Name
I/O
78
ILLIN
I
Auto dimmer control illumination line detection signal input terminal
“H” is input at dimmer detection Not used (fixed at “L”)
79
TELATT
I
Telephone detection signal input terminal At input of “H”, the signal is attenuated by –20 dB
Used for the MDX-C6500R/C6500RX only (MDX-C6400R: fixed at “L”)
80
NCO
O
Not used (open)
81
TEST IN
I
Setting terminal for the test mode “L”: test mode, Normally: fixed at “H”
82
ACC IN
I
Accessory detection signal input terminal “L”: accessory on
83
NCO
O
Not used (open)
84
LOCKIN
I
Mini-disc lock detection signal input from the MD mechanism controller (IC501) “H”: lock
85
RCIN1
I
Rotary remote commander shift key input terminal “L”: shift
86
HSTX
I
Hardware standby input terminal “L”: hardware standby mode Reset signal input in this set
87
MD2
I
Setting terminal for the CPU operational mode (fixed at “L” in this set)
88
MD1
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
89
MD0
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
90
RSTX
I
System reset signal input from the reset signal generator (IC652) and reset switch (SW503)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
91
VSS
—
92
X0
I
Main system clock input terminal (3.68 MHz)
93
X1
O
Main system clock output terminal (3.68 MHz)
94
VCC
—
Power supply terminal (+5V)
95 to 97
NCO
O
Not used (open)
98
DIM SEL
I
Setting terminal for the dimmer “L”: dimmer in, “H”: no dimmer (fixed at “H” in this set)
99
TAP CD
I
Setting terminal for the internal mechanism tape or CD
“L”: CD, “H”: tape (fixed at “L” in this set)
100, 101
NCO
O
Not used (open)
102
AMTL IN
I
Auto metal detection signal input terminal “L”: auto metal Not used (open)
103
AMS IN
I
Input terminal of whether a music is present or not is detected at auto music sensor
“L”: music is present, “H”: music is not present Not used (open)
104
REEL
I
Rotation detect signal input terminal Not used (open)
105
POS0
I
106
POS1
I
107
POS2
I
108
POS3
I
109
LM EJ
O
Loading motor control signal output terminal “H” active
(For the eject direction and reverse side operation) Not used (open)
110
LM LD
O
Loading motor control signal output terminal “H” active
(For the loading direction and forward side operation) Not used (open)
111
CM ON
O
Capstan/reel motor control signal output terminal “H”: motor on Not used (open)
112
TAPON
O
Tape system power supply on/off control signal output terminal “H”: tape on Not used (open)
113
N ROUT
O
Forward/reverse direction control signal output terminal
“L”: forward direction, “H”: reverse direction Not used (open)
114
AMSON
O
Tape auto music sensor control signal output terminal
“L” is output to lower the gain for audio level at FF/REW mode Not used (open)
I/O
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
At manual mode: METAL on/off control signal output terminal (METAL on at “H” output)
Not used this function (open)
115
48
MTLON
Description
Ground terminal
Tape position (EJECT/FF/REW/REV/
FWD mode) detect input from the tape
operation switch on the deck mechanism
Not used this function (open)
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS3: “L”: REV and EJECT mode, “H”: others mode
Pin No.
Pin Name
I/O
Description
116
DOLON
I/O
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (valid at “L” input)
At normal mode: dolby on/off control signal output terminal (dolby on at “H” output)
Not used this function (open)
117
TAPATT
O
Audio signal select control signal output terminal
118
NCO
O
Not used (open)
119
VSS
—
Ground terminal
120
PW ON
O
Main system power supply on/off control signal output to the BA4908 (IC671) “H”: power on
Not used (open)
49
Ver 1.2
SECTION 5
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
#11
(1)
GENERAL SECTION
#11
13
14
B
FU601
#3
15
11
C6500R/
C6500RX
#3
12
MG-164NZ-138
#3
#2
#4
TU1
A
9
10
#4
2
16
21
#11
not
supplied
22
3
8
7
4
B
17
A
#11
Front panel section
5
18
6
#10
#1
#12
#10
#1
#10
19
CNP811
1
Ref. No.
Part No.
Description
1
2
3
4
5
X-3378-458-1
X-3376-699-2
3-030-909-02
3-713-786-51
3-034-086-01
PANEL ASSY, SUB
GEAR ASSY
DAMPER, OIL
SCREW +P 2X3
SPRING (DOOR)
6
7
* 8
* 9
* 9
3-033-750-02
3-040-990-01
1-677-057-11
A-3294-867-A
A-3294-868-A
DOOR (MD)
BUTTON (EJECT) (Z)
SUB BOARD
MAIN BOARD, COMPLETE (C6400R)
MAIN BOARD, COMPLETE (C6500RX)
* 9
* 10
11
* 12
* 13
A-3294-943-A
3-041-011-01
3-376-464-11
3-040-998-01
3-041-017-01
MAIN BOARD, COMPLETE (C6500R)
HEAT SINK (REG)
SCREW (+PTT 2.6X6), GROUND POINT
BRACKET (IC)
BRACKET (MD)
50
Remark
Ref. No.
*
*
*
*
Part No.
Description
14
15
15
16
17
3-040-995-01
3-040-996-11
3-040-996-21
3-045-878-01
1-776-527-51
COVER
HEAT SINK (2P) (C6400R)
HEAT SINK (2P) (C6500R/C6500RX)
PLATE (TU), GROUND
CORD (WITH CONNECTOR) (ISO) (POWER)
(C6400R)
17
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
(C6500R/C6500RX)
3-040-994-21 CHASSIS
X-3377-621-2 LOCK ASSY
3-045-877-01 CUSHION (TU)
3-045-828-01 INSULATED PLATE
* 18
19
* 21
* 22
Remark
CNP811 1-792-195-11 CABLE, FLEXIBLE, FLAT
FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
TU1
A-3220-812-A TUNER UNIT (TUX-020)
(2)
FRONT PANEL SECTION
#13
not supplied
(KEY board)
56
55
64
59
63
62
53
61
54
60
66
LCD901
65
67
52
69
68
51
Part No.
Description
Part No.
Description
51
52
53
54
55
3-041-010-01
3-040-987-01
3-040-986-01
3-041-003-01
3-040-980-01
BUTTON (1-6/M) (MODE. 1. 2. 3. 4. 5. 6)
BUTTON (OFF)
BUTTON (MENU/SOUND)
BUTTON (LIST/ENTER) (DSPL. LIST. ENTER)
BUTTON (SOURCE)
64
65
66
67
68
X-3378-398-1
3-935-151-01
3-040-989-01
3-041-005-11
3-041-006-01
PANEL ASSY, FRONT BACK
SPRING (OPEN)
BUTTON (OPEN)
BUTTON (D) (D-BASS)
BUTTON (AF/TA)
56
* 59
60
* 61
* 62
3-040-981-01
3-040-997-01
1-694-660-11
3-041-371-01
3-040-993-01
KNOB (VOL)
PLATE (LCD), GROUND
CONDUCTIVE BOARD, CONNECTION
SHEET (REFLECTOR)
PLATE (LCD), LIGHT GUIDE
69
69
69
LCD901
X-3378-685-1
X-3378-686-1
X-3378-688-1
1-803-906-11
* 63
3-040-992-01 HOLDER (LCD)
Ref. No.
Remark
Ref. No.
Remark
FRONT PANEL (SV) ASSY (C6500R)
FRONT PANEL (SV) ASSY (C6400R)
FRONT PANEL (SV) ASSY (C6500RX)
DISPLAY PANEL, LIQUID CRYSTAL
(C6400R/C6500R)
LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)
51
(3)
MECHANISM DECK SECTION-1
(MG-164NZ-138)
112
#8
113
114
106
#6
111
107
109
115
109
110
116
109
117
118
105
#6
#6
#6
111
104
105
108
103
103
104
102
101
#5
Ref. No.
Part No.
Description
SERVO BOARD, COMPLETE
CHASSIS ASSY, MD
SPRING (FLOAT F), TENSION
SPRING (FLOAT B), TENSION
DAMPER, OIL
* 110
111
* 112
113
* 114
3-032-712-01
3-919-281-01
X-3376-800-1
3-035-932-01
X-3376-797-3
LEVER (LOCK R)
SPRING (CHUCKING)
COVER ASSY, MD
WASHER, STOPPER
LEVER (LE) ASSY
HOLDER ASSY
SPRING (HOLDER)
CUSHION (EJ2)
CUSHION (EJ3)
115
116
* 117
* 118
3-032-707-01
3-925-034-01
X-3376-798-1
3-032-711-01
SPRING (LEVER LE)
ROLLER (GEAR E)
ARM ASSY, CHUCKING
LEVER (LOCK L)
Ref. No.
Part No.
Description
* 101
* 102
103
104
105
A-3326-036-A
X-3376-799-1
3-032-714-02
3-921-111-01
3-919-273-01
* 106
107
* 108
* 109
X-3376-796-3
3-032-682-01
3-034-301-01
3-034-302-01
52
Remark
Remark
(4)
MECHANISM DECK SECTION-2
(MG-164NZ-138)
157
158
M903
159
M901
156
#9
#7
155
161
#9
162
160
#8
164
M902
163
#8
154
165
#7
152
153
166
151
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
151
152
153
154
* 155
2-626-617-01
A-3326-034-A
1-654-693-11
3-919-283-01
3-032-704-01
SCREW (2X8)
SENSOR BOARD, COMPLETE
SENSOR FLEXIBLE BOARD
BRACKET (SL)
BASE (SL)
156
157
158
159
* 160
3-919-297-01
A-3301-750-A
3-032-660-01
3-032-669-01
3-032-705-01
BRACKET (SP)
CHASSIS (OP) ASSY
BRACKET (LO)
SPRING (RACK), TENSION
BEARING (SL)
Remark
Ref. No.
Part No.
Description
161
162
163
164
0 165
X-3373-213-1
3-939-590-07
3-010-091-01
3-919-293-01
8-583-065-03
SCREW ASSY, FEED
SCREW (IB LOCK)
SPRING (SL FEED)
SHAFT (OPT S), GUIDE
OPTICAL PICK-UP KMS-241C/J1RP
3-920-537-01
A-3301-407-A
A-3291-190-A
A-3291-191-A
SHAFT (OPT L), GUIDE
MOTOR ASSY, SP (SPINDLE)
MOTOR ASSY, SL (SLED)
MOTOR ASSY, LO (LOADING)
166
M901
M902
M903
Remark
53
SECTION 6
ELECTRICAL PARTS LIST
KEY
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
1-694-660-11
3-040-992-01
3-040-993-01
3-040-997-01
3-041-371-01
*
*
*
*
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
Ref. No.
Part No.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Description
Remark
KEY BOARD
**********
LED902 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)
CONDUCTIVE BOARD, CONNECTION
HOLDER (LCD)
PLATE (LCD), LIGHT GUIDE
PLATE (LCD), GROUND
SHEET (REFLECTOR)
LED902 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)
LED903 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)
LED903 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)
(GREEN)
LED903 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)
LED904 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)
(GREEN)
< CAPACITOR >
LED904 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)
C951
C952
C953
C954
C955
1-164-004-11
1-163-037-11
1-163-251-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C956
1-164-489-11 CERAMIC CHIP
0.1uF
0.022uF
100PF
0.1uF
0.1uF
10%
10%
5%
10%
10%
25V
25V
50V
25V
25V
0.22uF
10%
16V
< CONNECTOR >
CN901
D901
D902
D903
D904
D951
8-719-158-49
8-719-056-82
8-719-056-82
8-719-056-82
8-719-976-99
D952
8-719-976-99 DIODE UDZ-TE-17-5.1B
DIODE
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-12B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-5.1B
< IC >
8-759-366-34 IC LC75824E
8-749-012-25 IC RS-170-TU
(REMOTE CONTROL RECEIVER)
< LIQUID CRYSTAL DISPLAY >
LCD901 1-803-906-11 DISPLAY PANEL, LIQUID CRYSTAL
(C6400R, C6500R)
LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)
< LED >
LED901 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)
LED901 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)
(GREEN)
LED901 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)
LED902 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)
54
8-719-061-16
8-719-078-19
8-719-078-19
8-719-078-19
(GREEN)
LED CL-190SR-CD-T (ILLUMINATION) (RED)
LED LWA673-R1S2*1 (LCD BACK LIGHT)
LED LWA673-R1S2*1 (LCD BACK LIGHT)
LED LWA673-R1S2*1 (LCD BACK LIGHT)
LED913 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)
LED914 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)
LED915 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)
1-794-065-21 PLUG, CONNECTOR 14P
< DIODE >
IC901
IC951
LED904
LED910
LED911
LED912
< SWITCH >
LSW901
LSW901
LSW901
LSW902
1-771-609-11
1-771-882-21
1-771-883-21
1-762-617-21
SWITCH, TACTILE (WITH LED) (OFF) (GREEN)
SWITCH, TACTILE (WITH LED) (OFF) (AMBER)
SWITCH, TACTILE (WITH LED) (OFF) (RED)
SWITCH, KEY BOARD (WITH LED) (SOURCE)
(AMBER)
LSW902 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (SOURCE)
(GREEN)
LSW902 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (SOURCE)
(RED)
LSW903 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (SOUND)
(AMBER)
LSW903 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (SOUND)
(GREEN)
LSW903 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (SOUND)
(RED)
LSW904 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (MENU)
(AMBER)
LSW904 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (MENU)
(GREEN)
LSW904 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (MENU)
(RED)
LSW905 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (PTY DSPL)
(AMBER)
LSW905 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (PTY DSPL)
(GREEN)
LSW905 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (PTY DSPL)
(RED)
KEY
Ref. No.
Part No.
Description
Remark
LSW906 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (LIST)
(AMBER)
LSW906 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (LIST)
(GREEN)
LSW906 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (LIST)
(RED)
LSW907 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (ENTER)
(AMBER)
LSW907 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (ENTER)
(GREEN)
LSW907 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (ENTER)
(RED)
LSW908 1-771-609-11 SWITCH, TACTILE (WITH LED) (MODE)
(GREEN)
LSW908 1-771-882-21 SWITCH, TACTILE (WITH LED) (MODE)
(AMBER)
LSW908 1-771-883-21 SWITCH, TACTILE (WITH LED) (MODE) (RED)
LSW909 1-762-737-11 SWITCH, KEY BOARD (WITH LED) (D-BASS)
LSW910 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (TA)
(AMBER)
LSW910 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (TA)
(GREEN)
LSW910 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (TA) (RED)
LSW911 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (AF)
(AMBER)
LSW911 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (AF)
(GREEN)
LSW911
LSW912
LSW912
LSW912
LSW913
1-771-476-11
1-771-609-11
1-771-882-21
1-771-883-21
1-771-609-11
SWITCH, KEY BOARD (WITH LED) (AF) (RED)
SWITCH, TACTILE (WITH LED) (6) (GREEN)
SWITCH, TACTILE (WITH LED) (6) (AMBER)
SWITCH, TACTILE (WITH LED) (6) (RED)
SWITCH, TACTILE (WITH LED) (5) (GREEN)
LSW913
LSW913
LSW914
LSW914
LSW914
1-771-882-21
1-771-883-21
1-771-609-11
1-771-882-21
1-771-883-21
SWITCH, TACTILE (WITH LED) (5) (AMBER)
SWITCH, TACTILE (WITH LED) (5) (RED)
SWITCH, TACTILE (WITH LED) (4) (GREEN)
SWITCH, TACTILE (WITH LED) (4) (AMBER)
SWITCH, TACTILE (WITH LED) (4) (RED)
LSW915
LSW915
LSW915
LSW916
1-771-609-11
1-771-882-21
1-771-883-21
1-771-609-11
SWITCH, TACTILE (WITH LED) (3) (GREEN)
SWITCH, TACTILE (WITH LED) (3) (AMBER)
SWITCH, TACTILE (WITH LED) (3) (RED)
SWITCH, TACTILE (WITH LED) (SHUF 2)
(GREEN)
LSW916 1-771-882-21 SWITCH, TACTILE (WITH LED) (SHUF 2)
(AMBER)
LSW916 1-771-883-21 SWITCH, TACTILE (WITH LED) (SHUF 2) (RED)
LSW917 1-771-609-11 SWITCH, TACTILE (WITH LED) (REP 1)
(GREEN)
LSW917 1-771-882-21 SWITCH, TACTILE (WITH LED) (REP 1)
(AMBER)
LSW917 1-771-883-21 SWITCH, TACTILE (WITH LED) (REP 1) (RED)
< RESISTOR >
R901
R902
R903
R904
R905
1-216-647-11
1-216-647-11
1-216-647-11
1-216-651-11
1-216-655-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
0.5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
1-216-655-11 METAL CHIP
1-216-659-11 METAL CHIP
1-216-663-11 METAL CHIP
1.5K
2.2K
3.3K
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
Remark
R909
R910
1-216-667-11 METAL CHIP
1-216-671-11 METAL CHIP
4.7K
6.8K
0.5%
0.5%
1/10W
1/10W
R911
R912
R913
R914
R915
1-208-806-11
1-216-647-11
1-216-647-11
1-216-647-11
1-216-651-11
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
680
680
680
1K
2%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R916
R917
R918
R919
R920
1-216-655-11
1-216-655-11
1-216-659-11
1-216-663-11
1-216-667-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
1.5K
2.2K
3.3K
4.7K
0.5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R921
1-216-807-11 METAL CHIP
68
5%
R921
1-216-810-11 METAL CHIP
120
5%
R921
1-216-811-11 METAL CHIP
150
5%
R923
1-216-807-11 METAL CHIP
68
5%
R923
1-216-811-11 METAL CHIP
150
5%
1/16W
(GREEN)
1/16W
(RED)
1/16W
(AMBER)
1/16W
(GREEN)
1/16W
(AMBER)
R923
1-216-812-11 METAL CHIP
180
5%
R925
1-216-021-00 METAL CHIP
68
5%
R925
1-216-029-00 METAL CHIP
150
5%
R925
1-216-031-00 METAL CHIP
180
5%
R927
1-216-021-00 METAL CHIP
68
5%
R927
1-216-029-00 METAL CHIP
150
5%
R927
1-216-031-00 METAL CHIP
180
5%
R931
R932
R933
1-216-813-11 METAL CHIP
1-216-813-11 METAL CHIP
1-216-808-11 METAL CHIP
220
220
82
5%
5%
5%
R933
1-216-812-11 METAL CHIP
180
5%
R933
1-216-813-11 METAL CHIP
220
5%
R938
R939
1-216-809-11 METAL CHIP
1-216-821-11 METAL CHIP
100
1K
5%
5%
R951
1-216-819-11 METAL CHIP
680
5%
1/16W
(AMBER)
1/16W
(RED)
1/16W
1/16W
(C6500RX)
1/16W
R952
R953
R954
R955
R956
1-216-021-00
1-216-857-11
1-216-049-11
1-216-049-11
1-216-821-11
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP
68
1M
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/16W
1/10W
1/10W
1/16W
R957
R958
R970
R971
R972
1-216-851-11
1-216-033-00
1-216-815-11
1-216-815-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330K
220
330
330
0
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
R973
R975
1-216-815-11 METAL CHIP
1-216-815-11 METAL CHIP
330
330
5%
5%
1/16W
1/16W
1/16W
(RED)
1/10W
(GREEN)
1/10W
(AMBER)
1/10W
(RED)
1/10W
(GREEN)
1/10W
(AMBER)
1/10W
(RED)
1/16W
1/16W
1/16W
(GREEN)
55
KEY
Ref. No.
MAIN
Part No.
Description
Remark
R976
R977
R980
1-216-815-11 METAL CHIP
1-216-815-11 METAL CHIP
1-216-864-11 METAL CHIP
330
330
0
5%
5%
5%
1/16W
1/16W
1/16W
R999
1-216-864-11 METAL CHIP
0
5%
1/16W
< ROTARY ENCODER >
RE901
1-475-014-12
ENCODER, ROTARY (VOLUME/BASS/TREBLE/
BALANCE/FADER CONTROL)
Ref. No.
Part No.
Description
C96
C97
C98
C101
C110
1-163-809-11
1-164-004-11
1-164-004-11
1-126-160-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.047uF
0.1uF
0.1uF
1uF
100PF
10%
10%
10%
20%
5%
25V
25V
25V
50V
50V
Remark
C111
C113
C121
C122
C123
1-109-982-11
1-109-982-11
1-164-004-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
0.1uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
10V
10V
25V
25V
25V
C131
C141
C142
C151
C152
1-124-233-11
1-163-251-11
1-126-160-11
1-162-970-11
1-124-584-00
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
10uF
100PF
1uF
0.01uF
100uF
20%
5%
20%
10%
20%
16V
50V
50V
25V
10V
C153
C156
C157
C159
C161
1-163-009-11
1-163-017-00
1-107-823-11
1-162-970-11
1-124-233-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
0.0047uF
0.47uF
0.01uF
10uF
10%
5%
10%
10%
20%
50V
50V
16V
25V
16V
C162
C171
C172
1-164-489-11 CERAMIC CHIP
1-126-163-11 ELECT
1-163-251-11 CERAMIC CHIP
C173
C174
1-164-489-11 CERAMIC CHIP
1-162-919-11 CERAMIC CHIP
10%
16V
20%
50V
5%
50V
(C6500R, C6500RX)
0.22uF
10%
16V
22PF
5%
50V
C181
C182
C183
C184
C191
1-126-163-11
1-163-251-11
1-164-489-11
1-162-919-11
1-216-295-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
SHORT
4.7uF
100PF
0.22uF
22PF
0
C192
C193
C201
C210
C241
1-216-295-00
1-216-295-00
1-126-160-11
1-163-251-11
1-163-251-11
SHORT
SHORT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0
0
1uF
100PF
100PF
C242
C271
C272
1-126-160-11 ELECT
1-126-163-11 ELECT
1-163-251-11 CERAMIC CHIP
1uF
4.7uF
100PF
C273
C274
1-164-489-11 CERAMIC CHIP
1-163-235-11 CERAMIC CHIP
20%
50V
20%
50V
5%
50V
(C6500R, C6500RX)
0.22uF
10%
16V
22PF
5%
50V
C281
C282
C283
C284
C361
1-126-163-11
1-163-251-11
1-164-489-11
1-162-919-11
1-164-004-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
100PF
0.22uF
22PF
0.1uF
20%
5%
10%
5%
10%
50V
50V
16V
50V
25V
C362
C363
C364
C368
C369
1-126-157-11
1-164-004-11
1-126-157-11
1-109-982-11
1-163-021-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
10uF
1uF
0.01uF
20%
10%
20%
10%
10%
16V
25V
16V
10V
50V
C370
C371
C372
C373
C374
1-163-021-11
1-163-021-11
1-163-021-11
1-163-021-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.01uF
0.01uF
0.01uF
100uF
10%
10%
10%
10%
20%
50V
50V
50V
50V
10V
C375
1-124-584-00 ELECT
100uF
20%
10V
< SWITCH >
S901
1-771-884-21 SWITCH, TACTILE (WITH LED)
(SEEK/AMS - . m)
S902
1-771-884-21 SWITCH, TACTILE (WITH LED)
(DISC +, PRST +)
S903
1-771-884-21 SWITCH, TACTILE (WITH LED)
(SEEK/AMS + > M)
S904
1-771-884-21 SWITCH, TACTILE (WITH LED)
(DISC -, PRST -)
**************************************************************
*
*
*
A-3294-867-A MAIN BOARD, COMPLETE (C6400R)
A-3294-868-A MAIN BOARD, COMPLETE (C6500RX)
A-3294-943-A MAIN BOARD, COMPLETE (C6500R)
*********************
*
3-040-996-11
3-040-996-21
3-040-998-01
3-041-011-01
7-685-647-79
*
*
HEAT SINK (2P) (C6400R)
HEAT SINK (2P) (C6500R, C6500RX)
BRACKET (IC)
HEAT SINK (REG)
SCREW +BVTP 3X10 TYPE2 IT-3
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-795-09 SCREW +PTT 2.6X12 (S)
< CAPACITOR/SHORT >
C1
C3
C4
C6
C7
1-163-233-11
1-124-584-00
1-164-004-11
1-164-004-11
1-124-589-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
18PF
100uF
0.1uF
0.1uF
47uF
5%
20%
10%
10%
20%
50V
10V
25V
25V
16V
C13
C14
C52
C53
C54
1-163-017-00
1-163-021-11
1-164-004-11
1-163-229-11
1-163-229-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
0.1uF
12PF
12PF
5%
10%
10%
5%
5%
50V
50V
25V
50V
50V
C55
C56
C57
C58
C59
1-164-004-11
1-124-589-11
1-164-004-11
1-163-263-11
1-164-505-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
47uF
0.1uF
330PF
2.2uF
10%
20%
10%
5%
25V
16V
25V
50V
16V
C60
C61
C62
C63
C90
1-163-135-00
1-164-161-11
1-163-009-11
1-164-315-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
560PF
0.0022uF
0.001uF
470PF
0.001uF
5%
10%
10%
5%
10%
50V
100V
50V
50V
50V
C91
C92
C93
C94
C95
1-162-964-11
1-162-964-11
1-163-133-00
1-162-915-11
1-107-823-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
470PF
10PF
0.47uF
10%
10%
5%
0.5PF
10%
50V
50V
50V
50V
16V
56
0.22uF
4.7uF
100PF
20%
5%
10%
5%
50V
50V
16V
50V
20%
5%
5%
50V
50V
50V
MAIN
Ref. No.
Part No.
Description
C502
C503
C504
C505
1-164-004-11
1-164-004-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
Remark
25V
25V
25V
25V
C506
C507
C508
C509
C510
1-163-235-11
1-163-235-11
1-165-319-11
1-163-021-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
22PF
22PF
0.1uF
0.01uF
100uF
5%
5%
Z%
10%
20%
50V
50V
50V
50V
10V
C511
C512
C513
C551
C552
1-164-004-11
1-163-133-00
1-163-125-00
1-164-222-11
1-164-222-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
470PF
220PF
0.22uF
0.22uF
10%
5%
5%
25V
50V
50V
25V
25V
C571
1-162-927-11 CERAMIC CHIP
100PF
C601
C602
C603
C611
1-135-473-21
1-163-251-11
1-162-927-11
1-126-160-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
5%
50V
(C6500R, C6500RX)
3300uF
20%
16V
100PF
5%
50V
100PF
5%
50V
1uF
20%
50V
C612
C614
C616
C617
C621
C622
1-126-160-11
1-126-157-11
1-107-823-11
1-136-165-00
1-124-589-11
1-126-160-11
ELECT
ELECT
CERAMIC CHIP
MYLAR
ELECT
ELECT
1uF
10uF
0.47uF
0.1uF
47uF
1uF
20%
20%
10%
5%
20%
20%
50V
16V
16V
50V
16V
50V
C623
C625
C631
C632
C641
C653
1-109-982-11
1-109-982-11
1-164-222-11
1-164-222-11
1-162-964-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
0.22uF
0.22uF
0.001uF
0.01uF
10%
10%
10%
10%
10V
10V
25V
25V
50V
50V
C654
C655
C661
C671
C672
1-125-710-11
1-124-584-00
1-109-982-11
1-126-157-11
1-126-157-11
DOUBLE LAYER
ELECT
CERAMIC CHIP
ELECT
ELECT
0.1F
100uF
1uF
10uF
10uF
20%
10%
20%
20%
5.5V
10V
10V
16V
16V
C673
C674
C675
C676
C682
1-126-157-11
1-124-233-11
1-124-233-11
1-126-157-11
1-163-021-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
10uF
10uF
10uF
10uF
0.01uF
20%
20%
20%
20%
10%
16V
16V
16V
16V
50V
C701
C702
C703
C704
C705
1-162-970-11
1-164-004-11
1-164-227-11
1-165-319-11
1-126-935-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
0.022uF
0.1uF
470uF
10%
10%
10%
25V
25V
25V
50V
16V
20%
< CONNECTOR >
CN301
CN500
CN601
CN701
1-764-617-12
1-784-456-11
1-774-701-11
1-580-907-31
PIN, CONNECTOR (PC BOARD) 30P
CONNECTOR, FFC/FPC 14P
PIN, CONNECTOR 16P
PLUG, CONNECTOR (BUS CONTROL IN)
< JACK >
CNJ151 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT)
(C6400R)
CNJ151 1-774-700-11 JACK, PIN 6P (BUS AUDIO IN,
AUDIO OUT REAR/FRONT) (C6500R, C6500RX)
Ref. No.
Part No.
Description
Remark
< DIODE >
D1
D2
D90
D91
D92
8-719-073-01
8-719-067-56
8-719-073-01
8-719-073-01
8-719-976-99
DIODE
DIODE
DIODE
DIODE
DIODE
MA111-TX
MA112-TX
MA111-TX
MA111-TX
UDZ-TE-17-5.1B
D131
D301
D302
D361
D362
8-719-422-12
8-719-914-44
8-719-073-01
8-719-034-74
8-719-158-15
DIODE
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-3.9B
DAP202K-T-146
MA111-TX
MA4120-M (TA)
UDZ-TE-17-5.6B
D501
D502
D551
D552
D553
8-719-914-44
8-719-073-01
8-719-158-49
8-719-056-82
8-719-056-82
DIODE
DIODE
DIODE
DIODE
DIODE
DAP202K-T-146
MA111-TX
UDZ-TE-17-12B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
D554
D555
D556
D557
D558
8-719-056-82
8-719-056-82
8-719-056-82
8-719-056-82
8-719-056-82
DIODE
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
D559
D560
D561
D562
D563
D564
D571
8-719-056-82
8-719-056-82
8-719-056-93
8-719-056-82
8-719-109-97
8-719-109-97
8-719-073-01
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-18B
UDZ-TE-17-6.2B
RD6.8ESB2
RD6.8ESB2
MA111-TX (C6500R, C6500RX)
D601
D602
D603
D604
D605
8-719-049-38
8-719-056-93
8-719-056-93
8-719-056-82
8-719-056-93
DIODE
DIODE
DIODE
DIODE
DIODE
1N5404TU
UDZ-TE-17-18B
UDZ-TE-17-18B
UDZ-TE-17-6.2B
UDZ-TE-17-18B (C6500R, C6500RX)
D611
D612
D613
D614
D615
8-719-079-55
8-719-079-55
8-719-079-55
8-719-079-55
8-719-079-55
DIODE
DIODE
DIODE
DIODE
DIODE
PTZ-TE25-22
PTZ-TE25-22
PTZ-TE25-22
PTZ-TE25-22
PTZ-TE25-22
D616
D617
D618
D621
D622
D623
8-719-079-55
8-719-079-55
8-719-079-55
8-719-422-12
8-719-073-01
8-719-158-15
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
PTZ-TE25-22
PTZ-TE25-22
PTZ-TE25-22
UDZ-TE-17-3.9B
MA111-TX
UDZ-TE-17-5.6B
D624
D631
D653
D661
D662
8-719-158-15
8-719-423-26
8-719-073-01
8-719-073-01
8-719-420-14
DIODE
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-5.6B
MA8110-H
MA111-TX
MA111-TX
MA8082-M (TX)
D671
D672
D673
D674
D675
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
8-719-067-56
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
MA112-TX
D676
D677
D701
D702
8-719-073-01
8-719-073-01
8-719-978-69
8-719-017-62
DIODE
DIODE
DIODE
DIODE
MA111-TX
MA111-TX
UDZ-TE-17-16B
MA8068-L-TX
57
MAIN
Ref. No.
Part No.
Description
Remark
D703
8-719-056-82 DIODE UDZ-TE-17-6.2B
D704
D705
D706
D708
D709
8-719-056-93
8-719-056-93
8-719-072-70
8-719-073-01
8-719-073-01
D710
8-719-073-01 DIODE MA111-TX
DIODE
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-18B
UDZ-TE-17-18B
MA2ZD14001S0
MA111-TX
MA111-TX
< COIL >
FB362
FB501
1-414-233-22 INDUCTOR CHIP 0uH
1-414-233-22 INDUCTOR CHIP 0uH
Ref. No.
Part No.
Description
Remark
Q121
Q131
8-729-920-21 TRANSISTOR DTC314TK-T-146
8-729-921-25 TRANSISTOR FMC2-T148
Q171
Q181
Q250
Q271
Q281
8-729-920-21
8-729-920-21
8-729-921-25
8-729-920-21
8-729-920-21
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC314TK-T-146
DTC314TK-T-146
FMC2-T148
DTC314TK-T-146
DTC314TK-T-146
Q361
Q362
Q363
Q551
Q571
8-729-019-00
8-729-019-00
8-729-921-25
8-729-921-25
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2394-G
2SD2394-G
FMC2-T148
FMC2-T148
2SC2412K-T-146-QR
(C6500R, C6500RX)
Q621
Q622
Q631
Q633
Q651
8-729-027-23
8-729-021-94
8-729-423-99
8-729-921-25
8-729-027-23
TRANSISTOR DTA114EKA-T146
FET 2SK1657-T1B
TRANSISTOR 2SD2137-OP-TA
TRANSISTOR FMC2-T148
TRANSISTOR DTA114EKA-T146
Q652
Q661
Q701
Q704
Q705
8-729-027-23
8-729-120-28
8-729-900-53
8-729-027-23
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q706
8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR
< FUSE >
FU601
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
< IC >
IC51
IC90
IC151
IC501
IC611
8-759-650-68
8-759-909-71
8-759-653-27
8-759-663-56
8-759-663-88
IC
IC
IC
IC
IC
SAA6588T/V2-118
BA4558F-E2
TDA7402TR
MB90574PMT-G-266-BND
TA8268H
IC652
IC671
IC701
8-759-574-61 IC XC61AN4302MR
8-759-661-47 IC BA4908-V3
8-759-449-89 IC BA8270F-E2
DTA114EKA-T146
2SC2412K-T-146-QR
DTC114EKA-T146
DTA114EKA-T146
DTA114EKA-T146
< RESISTOR >
< JACK >
J1
J501
1-764-808-21 JACK (ANT) (FM/AM ANTENNA)
1-566-822-41 JACK (REMOTE IN)
< RESISTOR >
R1
R4
R5
R6
R7
1-216-295-00
1-216-025-00
1-216-025-00
1-216-025-00
1-216-025-00
SHORT
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
0
100
100
100
100
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
JC1
JC2
JC4
JC5
JC16
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R8
R9
R12
R20
R53
1-216-295-00
1-216-041-00
1-216-837-11
1-216-057-00
1-216-853-11
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470
22K
2.2K
470K
5%
5%
5%
5%
1/10W
1/16W
1/10W
1/16W
JC31
JC50
JC54
JC90
JC191
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R54
R55
R56
R57
R58
1-216-821-11
1-216-061-00
1-216-817-11
1-216-809-11
1-216-025-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
1K
3.3K
470
100
100
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/10W
JC192
JC193
JC194
JC301
JC601
1-216-295-00
1-216-295-00
1-216-295-00
1-216-864-11
1-216-864-11
SHORT
SHORT
SHORT
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
1/16W
1/16W
R59
R60
R90
R91
R92
1-216-001-00
1-216-797-11
1-216-825-11
1-216-825-11
1-216-025-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
10
10
2.2K
2.2K
100
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/10W
JC671
JC673
1-216-295-00 SHORT
1-216-864-11 METAL CHIP
0
0
5%
1/16W
R93
R94
R95
R96
R97
1-216-845-11
1-216-829-11
1-216-121-00
1-216-025-00
1-216-833-11
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100K
4.7K
1M
100
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/10W
1/10W
1/16W
R98
R108
R111
R112
R121
1-216-833-11
1-216-295-00
1-216-864-11
1-216-841-11
1-216-049-11
RES, CHIP
SHORT
METAL CHIP
METAL CHIP
RES, CHIP
10K
0
0
47K
1K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/10W
R122
1-216-085-00 METAL CHIP
33K
5%
1/10W
< COIL >
L601
L671
1-419-476-21 COIL, CHOKE (2000) 250uH
1-410-989-11 INDUCTOR CHIP 0.47uH
< TRANSISTOR >
Q1
Q90
Q111
58
8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR
8-729-900-53 TRANSISTOR DTC114EKA-T146
8-729-920-21 TRANSISTOR DTC314TK-T-146
MAIN
Ref. No.
Part No.
Description
R131
R132
R141
R142
1-216-037-00
1-216-045-00
1-216-025-00
1-216-073-00
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
330
680
100
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Remark
R152
R153
R154
R156
R171
1-216-841-11
1-216-025-00
1-216-025-00
1-216-809-11
1-216-033-00
METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP
47K
100
100
100
220
5%
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/16W
1/10W
R172
R173
R181
R182
R183
1-216-081-00
1-216-089-00
1-216-033-00
1-216-081-00
1-216-089-00
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
RES, CHIP
22K
47K
220
22K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R208
R241
R242
R271
R272
1-216-295-00
1-216-025-00
1-216-073-00
1-216-033-00
1-216-081-00
SHORT
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
10K
220
22K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R273
R281
R282
R283
R361
1-216-089-00
1-216-033-00
1-216-081-00
1-216-089-00
1-216-041-00
RES, CHIP
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
47K
220
22K
47K
470
5%
5%
5%
5%
5%
R362
R363
R364
R504
R505
1-216-041-00
1-216-041-00
1-216-041-00
1-216-057-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
470
2.2K
2.2K
R506
R507
R509
R520
R522
1-216-057-00
1-216-073-00
1-216-097-00
1-216-097-00
1-216-097-00
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
R523
R524
R525
R526
R529
1-216-845-11
1-216-073-00
1-216-073-00
1-216-097-00
1-216-049-11
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
R531
1-216-839-11 METAL CHIP
33K
R532
1-216-833-11 RES, CHIP
10K
R533
1-216-833-11 RES, CHIP
10K
R534
1-216-097-00 RES, CHIP
100K
R535
1-216-845-11 METAL CHIP
100K
R537
R538
R539
R540
R542
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
1-216-089-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100K
100K
100K
100K
47K
R545
R546
R547
R551
1-216-097-00
1-216-097-00
1-216-097-00
1-249-409-11
RES, CHIP
RES, CHIP
RES, CHIP
CARBON
100K
100K
100K
220
Ref. No.
Part No.
Description
Remark
R551
1-249-413-11 CARBON
470
5%
1/4W
(C6500RX)
R552
R553
R554
R555
R556
1-216-025-00
1-216-025-00
1-216-025-00
1-216-025-00
1-216-025-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R557
R558
R559
R560
R561
1-216-025-00
1-216-025-00
1-216-025-00
1-216-025-00
1-208-806-11
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100
100
100
100
10K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R562
R563
R564
R565
R567
1-208-806-11
1-216-845-11
1-216-845-11
1-216-025-00
1-249-411-11
RES, CHIP
METAL CHIP
METAL CHIP
RES, CHIP
CARBON
10K
100K
100K
100
330
0.5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/10W
1/4W
R571
1-216-845-11 METAL CHIP
100K
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R572
R573
R600
R601
R603
1-216-809-11
1-216-809-11
1-216-097-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
100
100
100K
10K
10K
5%
5%
5%
5%
5%
1/16W
(C64OOR)
1/16W
1/16W
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R611
R612
R621
R622
R624
1-216-833-11
1-216-073-00
1-216-805-11
1-216-864-11
1-216-295-00
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
10K
10K
47
0
0
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
2.2K
10K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R626
R631
R632
R636
R641
1-216-861-11
1-249-385-11
1-249-385-11
1-216-037-00
1-216-849-11
METAL CHIP
CARBON
CARBON
METAL CHIP
METAL CHIP
2.2M
2.2
2.2
330
220K
5%
5%
5%
5%
5%
1/16W
1/6W
1/6W
1/10W
1/16W
100K
10K
10K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/10W
1/10W
1/10W
1/10W
R642
R651
R652
R653
R654
1-216-853-11
1-216-113-00
1-216-845-11
1-208-806-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
470K
470K
100K
10K
10K
5%
5%
5%
0.5%
5%
1/16W
1/10W
1/16W
1/10W
1/16W
R655
R656
R661
R662
R663
1-216-809-11
1-216-809-11
1-249-421-11
1-216-081-00
1-216-841-11
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
100
100
2.2K
22K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/4W
1/10W
1/16W
R664
R682
R701
R702
R703
1-216-841-11
1-216-089-00
1-216-805-11
1-216-073-00
1-216-025-00
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
RES, CHIP
47K
47K
47
10K
100
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/10W
1/10W
R704
R707
R713
R714
R715
1-216-809-11
1-216-065-00
1-216-841-11
1-216-841-11
1-216-845-11
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
4.7K
47K
47K
100K
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
R716
1-216-809-11 METAL CHIP
100
5%
1/16W
5%
1/16W
(C6500R, C6500RX)
5%
1/16W
(C6500R, C6500RX)
5%
1/16W
(C6500R, C6500RX)
5%
1/10W
(C6500R, C6500RX)
5%
1/16W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/4W
(C6400R, C6500R)
59
Ver 1.2
MAIN
Ref. No.
SENSOR
Part No.
SERVO
Description
Remark
< SWITCH >
SW503 1-692-431-21 SWITCH, TACTILE (RESET)
SW504 1-771-540-11 SWITCH, PUSH (1KEY) (NOSE DETECT)
< THERMISTOR >
TH701
1-803-350-21 THERMISTOR, POSITIVE
Ref. No.
Part No.
Description
Remark
C325
C326
C327
1-110-563-11 CERAMIC CHIP
1-162-968-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
0.068uF 10%
0.0047uF 10%
1uF
10%
16V
50V
10V
C328
C329
C330
C331
C333
1-162-966-11
1-164-227-11
1-162-970-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.022uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
25V
25V
16V
16V
C334
C335
C336
C337
C338
1-164-004-11
1-164-004-11
1-162-970-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C339
C340
C341
C342
C343
1-162-970-11
1-162-918-11
1-162-918-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
18PF
18PF
0.01uF
0.01uF
10%
5%
5%
10%
10%
25V
50V
50V
25V
25V
C344
C345
C346
C347
C348
1-104-852-11
1-162-970-11
1-104-852-11
1-162-970-11
1-107-826-11
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.01uF
22uF
0.01uF
0.1uF
20%
10%
20%
10%
10%
10V
25V
6.3V
25V
16V
C349
C350
C351
C352
C353
1-107-826-11
1-107-826-11
1-104-852-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
22uF
0.1uF
0.1uF
10%
10%
20%
10%
10%
16V
16V
10V
16V
16V
C356
C357
C358
C359
C361
1-162-927-11
1-162-927-11
1-162-927-11
1-162-923-11
1-135-259-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
100PF
100PF
100PF
47PF
10uF
5%
5%
5%
5%
20%
50V
50V
50V
50V
6.3V
C362
C402
C403
C501
C503
1-107-826-11
1-162-970-11
1-107-826-11
1-162-927-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.1uF
100PF
0.1uF
10%
10%
10%
5%
10%
16V
25V
16V
50V
16V
C504
C505
C506
C510
C511
1-107-826-11
1-107-826-11
1-104-852-11
1-115-467-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
22uF
0.22uF
0.1uF
10%
10%
20%
10%
10%
16V
16V
10V
10V
16V
C512
C513
C514
C515
C516
1-107-826-11
1-107-826-11
1-115-467-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.22uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
10V
16V
16V
< TUNER >
TU1
A-3220-812-A TUNER UNIT (TUX-020)
< VIBRATOR >
X51
1-579-242-41 VIBRATOR, CRYSTAL (4.332MHz)
X501
1-767-833-21 VIBRATOR, CERAMIC (3.68MHz)
X502
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
**************************************************************
A-3326-034-A SENSOR BOARD, COMPLETE
************************
For the parts on the SENSOR board, replace the entire mounted board.
**************************************************************
A-3326-036-A SERVO BOARD, COMPLETE
**********************
*
< CAPACITOR >
C11
C101
C102
C103
C104
1-162-964-11
1-104-543-11
1-135-259-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
FILM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0022uF
10uF
0.01uF
0.1uF
10%
5%
20%
10%
10%
50V
50V
6.3V
25V
16V
C105
C106
C107
C108
C109
1-107-826-11
1-135-181-21
1-162-970-11
1-162-970-11
1-135-181-21
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.1uF
4.7uF
0.01uF
0.01uF
4.7uF
10%
20%
10%
10%
20%
16V
6.3V
25V
25V
6.3V
C201
C202
C301
C302
C304
1-104-543-11
1-135-259-11
1-107-826-11
1-107-826-11
1-162-927-11
FILM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
10uF
0.1uF
0.1uF
100PF
5%
20%
10%
10%
5%
50V
6.3V
16V
16V
50V
C305
C306
C307
C308
C309
1-162-970-11
1-107-823-11
1-107-826-11
1-162-927-11
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.47uF
0.1uF
100PF
0.0047uF
10%
10%
10%
5%
10%
25V
16V
16V
50V
50V
C310
C311
C314
C315
C316
1-107-823-11
1-164-245-11
1-107-826-11
1-109-982-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.015uF
0.1uF
1uF
0.1uF
10%
10%
10%
10%
10%
16V
25V
16V
10V
16V
C317
C318
C319
C320
C321
1-107-826-11
1-104-852-11
1-104-852-11
1-164-227-11
1-162-969-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
22uF
0.022uF
0.0068uF
10%
20%
20%
10%
10%
16V
6.3V
6.3V
25V
25V
C322
C324
1-162-964-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.001uF
0.1uF
10%
10%
50V
16V
60
< CONNECTOR >
CN101
CN102
CN103
1-764-616-12 HOUSING, CONNECTOR (PC BOARD) 30P
1-573-929-21 CONNECTOR, FFC/FPC (ZIF) 20P
1-764-439-21 CONNECTOR, FPC 11P
< DIODE >
D401
D501
8-719-157-93 DIODE DTZ-TT11-3.0B
8-719-988-61 DIODE 1SS355TE-17
SERVO
Ref. No.
Part No.
Description
Remark
< FERRITE BEAD >
FB301
FB302
1-414-235-22 FERRITE BEAD INDUCTOR CHIP
1-414-760-21 FERRITE BEAD INDUCTOR CHIP
0uH
0uH
Ref. No.
Part No.
Description
R324
R325
R327
R328
R329
1-216-827-11
1-216-821-11
1-216-821-11
1-216-811-11
1-216-819-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
1K
1K
150
680
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Remark
R330
R331
R332
R333
R334
1-216-853-11
1-216-809-11
1-216-809-11
1-216-819-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
100
100
680
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R335
R336
R337
R338
R339
1-216-815-11
1-216-853-11
1-216-853-11
1-216-833-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
330
470K
470K
10K
3.3K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R340
R341
R342
R343
R344
1-216-843-11
1-216-837-11
1-216-833-11
1-216-827-11
1-216-833-11
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
RES, CHIP
68K
22K
10K
3.3K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< IC >
IC101
IC301
IC302
IC303
IC304
8-759-571-84
8-752-384-47
8-752-080-95
8-759-430-25
8-759-096-87
IC
IC
IC
IC
IC
PCM1718E/2K
CXD2652AR
CXA2523AR
BH6511FS-E2
TC7WU04FU (TE12R)
IC305
IC306
IC307
IC401
IC501
8-759-040-83
8-759-058-62
8-759-368-16
8-759-909-71
8-752-909-21
IC
IC
IC
IC
IC
BA6287F
TC7S08FU (TE85R)
MN41V4400TT-08S
BA4558F-E2
CXP84340-217Q
IC502
IC503
8-759-238-47 IC TC74HCT7007AF (EL)
8-759-238-47 IC TC74HCT7007AF (EL)
< COIL >
L101
L102
L301
L302
L303
1-412-058-11
1-412-058-11
1-412-058-11
1-412-058-11
1-412-039-51
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
10uH
10uH
10uH
10uH
100uH
R345
R346
R347
R348
R349
1-216-827-11
1-216-841-11
1-216-833-11
1-218-863-11
1-216-025-00
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
3.3K
47K
10K
4.7K
100
5%
5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/10W
L304
L305
L306
L501
1-412-039-51
1-412-039-51
1-412-039-51
1-412-058-11
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
100uH
100uH
100uH
10uH
R350
R351
R352
R353
R354
1-216-142-00
1-218-855-11
1-218-855-11
1-218-855-11
1-216-857-11
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
4.7
2.2K
2.2K
2.2K
1M
5%
0.5%
0.5%
0.5%
5%
1/8W
1/16W
1/16W
1/16W
1/16W
R355
R356
R357
R359
R401
1-216-833-11
1-216-833-11
1-216-017-00
1-216-864-11
1-216-073-00
RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP
10K
10K
47
0
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/10W
1/16W
1/10W
R402
R403
R404
R405
R406
1-216-065-00
1-216-065-00
1-216-809-11
1-218-847-11
1-218-869-11
RES, CHIP
RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP
4.7K
4.7K
100
1K
8.2K
5%
5%
5%
0.5%
0.5%
1/10W
1/10W
1/16W
1/16W
1/16W
R501
R502
R503
R504
R505
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R506
R507
R510
R511
R512
1-216-845-11
1-218-863-11
1-216-845-11
1-216-847-11
1-216-845-11
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
4.7K
100K
150K
100K
5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R516
R517
R518
R519
R520
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R521
R522
R523
1-216-809-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
100
1K
1K
5%
5%
5%
1/16W
1/16W
1/16W
< TRANSISTOR >
Q301
Q302
Q401
Q402
Q403
8-729-230-49
8-729-026-49
8-729-920-85
8-729-106-60
8-729-421-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2712Y-TE85L
2SA1037AK-T146-QR
2SD1664-T101-QR
2SB1132-T101-QR
UN2211-TX
< RESISTOR >
R101
R102
R104
R201
R202
1-216-073-00
1-216-833-11
1-216-049-11
1-216-073-00
1-216-049-11
METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP
RES, CHIP
10K
10K
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/16W
1/10W
1/10W
1/10W
R301
R302
R303
R304
R305
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R306
R307
R308
R311
R312
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
1K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R316
R317
R318
R319
R320
1-216-821-11
1-216-809-11
1-216-833-11
1-216-845-11
1-216-855-11
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
1K
100
10K
100K
680K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
61
SERVO
Ref. No.
SUB
Part No.
Description
Remark
R524
R525
1-216-821-11 METAL CHIP
1-216-845-11 METAL CHIP
1K
100K
5%
5%
1/16W
1/16W
R526
R527
R528
R529
R530
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R531
R532
R533
R534
R535
1-216-845-11
1-216-864-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
0
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R536
R537
R538
R539
R540
1-216-864-11
1-216-809-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R542
1-216-845-11 METAL CHIP
100K
5%
1/16W
Ref. No.
Part No.
Description
17
17
60
153
0 165
CNP811
M901
M902
M903
LCD901
1-776-527-51 CORD (WITH CONNECTOR) (ISO) (POWER)
(C6400R)
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
(C6500R/C6500RX)
1-694-660-11 CONDUCTIVE BOARD, CONNECTION
1-654-693-11 SENSOR FLEXIBLE BOARD
8-583-065-03 OPTICAL PICK-UP KMS-241C/J1RP
1-792-195-11
A-3301-407-A
A-3291-190-A
A-3291-191-A
1-803-906-11
1-233-576-11 RES, CHIP NETWORK 100
1-233-576-11 RES, CHIP NETWORK 100
1-233-412-11 RES, CHIP NETWORK 1K (3216)
< THERMISTOR >
TH501
1-810-421-11 THERMISTOR NTH5G36B103K01TE
< VIBRATOR >
X301
1-767-429-21 VIBRATOR, CRYSTAL (22.5792MHz)
X501
1-760-365-11 VIBRATOR, CERAMIC (10MHz)
**************************************************************
1-677-057-11 SUB BOARD
**********
*
< CONNECTOR >
CNP810 1-794-064-11 SOCKET, CONNECTOR 14P
CNP811 1-792-195-11 CABLE, FLEXIBLE FLAT
< DIODE >
D806
D810
D811
D812
D813
D814
8-719-109-97
8-719-056-82
8-719-056-82
8-719-056-82
8-719-056-82
8-719-056-82
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ESB2
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
UDZ-TE-17-6.2B
< LED >
LED810 8-719-077-75 LED BR1101F-TR (MD DISC SLOT) (C6500RX)
LED810 8-719-077-78 LED BG1101F-TR (MD DISC SLOT)
(C6400R, C6500R)
CABLE, FLEXIBLE, FLAT
MOTOR ASSY, SP (SPINDLE)
MOTOR ASSY, SL (SLED)
MOTOR ASSY, LO (LOADING)
DISPLAY PANEL, LIQUID CRYSTAL
(C6400R/C6500R)
LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)
************************************************************
**************
HARDWARE LIST
**************
< COMPOSITION CIRCUIT BLOCK >
RB301
RB302
RB503
Remark
MISCELLANEOUS
**************
#1
#2
#3
#4
#5
7-621-772-20
7-685-795-09
7-685-793-09
7-685-647-79
7-685-851-04
SCREW +B 2X5
SCREW +PTT 2.6X12 (S)
SCREW +PTT 2.6X8 (S)
SCREW +BVTP 3X10 TYPE2 IT-3
SCREW +BVTT 2X4 (S)
#6
#7
#8
#9
#10
7-624-102-04
7-627-852-37
7-621-772-08
7-621-555-10
7-685-793-09
STOP RING 1.5, TYPE-E
PRECISION SCREW +P 1.7X1.8 TYPE 3
SCREW +B 2X3
SCREW +K 2X3
SCREW +PTT 2.6X8 (S)
#11
7-685-791-09 SCREW +PTT 2.6X5 (S)
#12
7-627-553-28 SCREW, PRECISION +P 2X2.5
#13
7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT
************************************************************
ACCESSORIESE & PACKING MATERIALS
*********************************
3-044-659-11 MANUAL, INSTRUCTION (ENGLISH, SPANISH,
SWEDISH, PORTUGUESE, RUSSIAN)
(C6500R/C6500RX: AEP, UK)
3-044-659-21 MANUAL, INSTRUCTION (FRENCH, GERMAN,
DUTCH, ITALIAN, GREEK)
(C6400R/C6500R/C6500RX: AEP)
3-044-659-31 MANUAL, INSTRUCTION (GERMAN)
(C6400R/C6500R/C6500RX: German)
3-044-660-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH, SWEDISH, PORTUGUESE, RUSSIAN)
(C6500R/C6500RX: AEP, UK)
3-044-660-21 MANUAL, INSTRUCTION, INSTALL (FRENCH,
GERMAN, DUTCH, ITALIAN, GREEK)
(C6400R/C6500R/C6500RX: AEP)
X-3378-490-1 CASE (PANEL) ASSY
************************************************************
< SWITCH >
LSW810 1-771-609-11 SWITCH, TACTILE (WITH LED) (Z)
(C6400R, C6500R)
LSW810 1-771-883-21 SWITCH, TACTILE (WITH LED) (Z) (C6500RX)
**************************************************************
62
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ver 1.1 2001.05
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
PARTS FOR INSTALLATION AND CONNECTION
*************************************
501
502
503
504
505
1-465-459-21
3-012-360-31
3-040-979-01
3-233-644-01
3-934-325-01
506
507
X-3366-405-1 SCREW ASSY (EXP), FITTING
1-776-527-51 CORD (WITH CONNECTOR) (ISO) (POWER)
(C6400R)
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
(C6500R/C6500RX)
507
ADAPTER, ANTENNA
FRAME
COLLAR
SPRING, FITTING
SCREW, +K (5X8) TAPPING
501
502
ADAPTER, ANTENNA
×1
FRAME
×1
503
504
SPRING, FITTING
×2
COLLAR
×1
505
+K5 × 8
×2
506
SCREW, FITTING
×1
BUSHING
×1
507
POWER CORD
×1
63
MDX-C6400R/C6500R/C6500RX
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.2
1.1
1.0
Date
2001.12
2001.05
2000.02
Description of Revision
Change of Part No. for TU1
Change of Part No. for SPRING, FITTING
New
(RPC-01002)
(ECN-CSA04727)