Download Snapper 2395 User's Manual

Attachment
Illustrated
Parts List
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
© Copyright 2000 Simplicity Manufacturing, Inc.All Rights Reserved.
Rev. 10/2000
TP 400-2395-00-AT-SMA
Front Hydraulic Angling & Lift Kit
985565
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
21
16
1
7
6
17
20
3
5
18
5
4
3
2
19
5
17
9
16
26
58
7
12
5
13
5
12
5
10
5
11
58
15
5
10
15
5
14
5
The above parts group applies to the following Mfg. Nos.:
1693566 Front Hydralic Angling & Lift Kit
© Copyright 2000 Simplicity Manufacturing, Inc. All Rights Reserved.
2
TP 400-2395-00-AT-SMA
Front Hydraulic Angling & Lift Kit
REF NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PART NO.
1701011
1960277
1918452
1677214
1700394
919171
173359
1719395
1719565
1719586
1931277
919171
1716944
1711773
176012
1916951
1916966
1717645
1717642
1920328
1960286
QTY.
3
1
3
1
1
2
4
2
2
1
2
4
1
2
2
4
4
1
1
2
2
DESCRIPTION
TIE, Self Locking
PIN, Yoke
PIN, Cotter
ANGLING CYLINDER ASSEMBLY
PIN, Flat Head, Drilled, 5/8 x 1-5/8
FITTING
NOSE PIECE ASSEMBLY
HOSE ASSEMBLY, Length 17.0”
HOSE ASSEMBLY, Length 50.0”
HOSE SUPPORT
NUT, Hex, 5/16-18
TUBE FITTING, Male
LIFT CYLINDER ASSEMBLY
PIN, Clevis
PIN, Retainer
NUT, Hex, 1/2-13
LOCKWASHER, 1/2
SUPPORT ASSEMBLY, Cylinder
CLAMP, Plate
CAPSCREW, Hex Head,1/2-13 x 1-1/2
CAPSCREW, Hex Head,1/2-13 x 3-1/2
Footnotes:
The above parts group applies to the following Mfg. Nos.:
1693566 Front Hydralic Angling & Lift Kit
TP 400-2395-00-AT-SMA
3
Hardware Identification & Torque Specifications
Common Hardware Types
Torque Specification Chart
Hex Head Capscrew
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Washer
Hardware
Grade
Lockwasher
Carriage Bolt
No
Marks
SAE Grade 2
Hex Nut
Size Of
Hardware
Standard Hardware Sizing
8-32
8-36
10-24
10-32
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
7/8-14
1-8
1-12
When a washer or nut is identified as 1/2”, this is the
Nominal size, meaning the inside diameter is 1/2 inch; if a
second number is present it represent the threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the Nominal size, or body diameter is 1/2 inch; the
second number represents the threads per inch (16 in this
example, and the final number is the body length of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4
Nut, 1/2”
1/2
Inside
Diameter
3/4
1
1/4
1/2
3/4
Screw, 1/2 x 2
2
1/4
Body
Diameter
in/lbs
ft/lbs
19
20
27
31
66
76
11
12
20
23
30
35
50
55
65
75
90
100
160
180
140
155
220
240
Nm.
2.1
2.3
3.1
3.5
7.6
8.6
15.0
16.3
27.2
31.3
40.8
47.6
68.0
74.8
88.4
102.0
122.4
136
217.6
244.8
190.4
210.8
299.2
326.4
SAE Grade 5
in/lbs
ft/lbs
30
31
43
49
8
10
17
19
30
35
50
55
75
90
110
120
150
180
260
300
400
440
580
640
SAE Grade 8
Nm.
in/lbs
ft/lbs
Nm.
3.4
3.5
4.9
5.5
10.9
13.6
23.1
25.8
40.8
47.6
68.0
74.8
102.0
122.4
149.6
163.2
204.0
244.8
353.6
408.0
544.0
598.4
788.8
870.4
41
43
60
68
12
14
25
27
45
50
70
80
110
120
150
170
220
240
386
420
600
660
900
1,000
4.6
4.9
6.8
7.7
16.3
19.0
34.0
34.0
61.2
68.0
95.2
108.8
149.6
163.2
204.0
231.2
299.2
326.4
525.0
571.2
816.0
897.6
1,244.0
1,360.0
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
1/2
Body
Length
3/4
3
1/4
1/2
3/4
4
Wrench & Fastener Size Guide
1/4
5/16
3/8
1/4” Bolt or Nut
Wrench—7/16”
5/16” Bolt or Nut
Wrench—1/2”
3/8” Bolt or Nut
Wrench—9/16”
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”