Download Network Computing Devices GW-EN11H User's Manual

GW-EN11H
Wireless Ethernet
Adapter
(Color of this device may vary with regions)
User’s Manual
Version 1.0
February 19, 2002
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
y
Reorient or relocate the receiving antenna.
y
Increase the separation between the equipment and receiver.
y
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
y
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and should be installed and operated with minimum distance 20cm between
the radiator & your body.
CE Marking Warning
This is a Class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
2
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Table of Contents
1.
INTRODUCTION .......................................................................................................... 5
THE WIRELESS ETHERNET ADAPTER FEATURES ............................................................... 5
PACKAGE CONTENTS ........................................................................................................... 6
2.HARDWARE INSTALLATION ........................................................................................ 7
PHYSICAL DETAILS REAR PANEL....................................................................................... 7
HARDWARE INSTALLATION.................................................................................................. 9
CONNECTING THE ETHERNET ADAPTER TO YOUR NETWORK ......................................... 10
3. WIRELESS NAVIGATOR INSTALLATION ............................................................... 11
INSTALL THE WIRELESS NAVIGATOR ................................................................................ 11
STARTUP AND LOGIN .......................................................................................................... 15
4. CONFIGURING THE ETHERNET ADAPTER .......................................................... 18
THE INFO TAB .................................................................................................................... 18
THE WIRELESS TAB ........................................................................................................... 19
THE SERVER TAB ............................................................................................................... 21
THE ADMIN TAB ................................................................................................................. 21
THE HELP TAB ................................................................................................................... 22
6. FAQ & TROUBLESHOOTING ..................................................................................... 23
7. PRODUCT SPECIFICATIONS...................................................................................... 25
3
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
About this manual
This user’s manual describes how to install and operate the Wireless Ethernet Adapter
(Adapter). Please read this manual before you install the product.
This manual includes the following topics:
¾ Product description, features and specifications
¾ Hardware installation procedures
¾ Software installation procedures
¾ Trouble shooting procedures
4
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
1. Introduction
Thank you for purchasing the GW-EN11H Wireless Ethernet Adapter. This Ethernet adapter
provides you with an innovative wireless networking solution. The GW-EN11H is easy to set
up and use. With this innovative wireless technology, you can share files and network
resources on the network—without inconvenient wires!
The Wireless Ethernet Adapter Features
LAN Features
z
DHCP Client – Enable the adapter to act as a DHCP client to receive IP address from
DHCP Server in the wired Ethernet LAN.
z
Built-in 10BaseT LAN Port – It’s designed to connect the adapter with any
Ethernet-ready devices, such as desktop PC, printer server and network
printer/scanner.
Wireless Features
z
Standard Compliant – The adapter complies with IEEE802.11b standard, and it is
interoperable with IEEE802.11b-Compliant Equipment
z
Data Rate Auto Fall-Back - Provides 11, 5.5, 2 and 1Mbps wireless data rate shifting
dynamically to guarantee availability and reliability of wireless connections
z
Roaming – Provides seamless roaming within 802.11b wireless LAN infrastructure.
z
Long Distance Reach – Support 80M indoor and 300M outdoors long operating
distance under normal environment condition.
Configuration & Management
z
Easy to Setup – With windows-based Wireless Navigator Utility, user can easily setup
the IP address of this adapter, and upgrade the firmware.
z
Easy to manage – User can use any WEB browser from anywhere on the wired or
wireless LAN to configure the adapter easily.
Security
z
Configuring Protection – Provides password protection to prevent unauthorized users
from changing the configuration
z
Wireless LAN Security - Provide 64-bit & 128-bit Wired Equivalent Privacy encryption
to protect the wireless data transmissions.
5
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Package Contents
z
One 11Mbps Wireless Ethernet adapter with dipole antenna connected
z
One CD-ROM (Wireless Navigator utility software & user’s manual included)
z
One RJ-45 straight LAN Cable
z
One Power Adapter
z
One Quick Installation Guide
If any of the above items are damaged or missing, please contact your dealer immediately.
6
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
2.Hardware Installation
Physical Details
Rear Panel
INIT Button
LAN Connection
LAN Cable
Selection Switch
INIT Button
Power Input
“INIT” mean “Initiation”. While pressing the button, the adapter will
reboot and ERASE current settings, and restore to factory default
settings. The left indicator “DIAG” will be off and then begin
blinking. Then this initiation action will be completed when the
indicator “ DIAG” is always green instead of blinking.
LAN Cable
Selection Switch
X
Crossover: the RJ-45 port Tx and Rx lines are
reversed. Use this setting when you have a straight
cable connected to PC. It is also the factory default
setting.
II
Straight: the RJ-45 port Tx and Rx lines are normal.
Use this setting when you have a crossover cable
connected.
Power Input
Please only use the power adapter supplied
LAN Connection
Use standard RJ-45 Ethernet cable to connect your PC, or any
Ethernet-ready device, such as printer server.
7
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
LED Indications
Ethernet
Wireless
LED
Ethernet
WLAN
Color
Green
Green
Status
Description
ON
The LAN port is linked
Blinking
The LAN port is sending or receiving data
OFF
No data forwarding between wireless and LAN ports.
Blinking
Sending or Receiving data via wireless
8
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Hardware Installation
Following illustration is an example showing how to install adapter with your PC.
Be sure to use the supplied power adapter.
Note!
You may also connect the adapter to other Ethernet-ready device, such as printer
server.
9
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Connecting the Ethernet Adapter to Your Network
There are two network scenarios as below:
Also known as a peer-to-peer network, an ad-hoc network is
one that allows all workstations and computers in the network
to act as servers to all other users on the network.
Ad-hoc
Networking
Users on the network can share files, print to a shared printer,
and access the Internet with a shared modem. However, with
ad-hoc networking, users can only communicate with other
wireless LAN computers that are in the same wireless LAN
workgroup, and are within range.
Infrastructure networking differs from ad-hoc networking in
that it includes an access point. Unlike the ad-hoc structure
where users on the LAN contend the shared bandwidth, on
Infrastructure an infrastructure network, the access point can manage the
Networking
bandwidth to maximize bandwidth utilization.
Additionally, the access point enables users on a wireless
LAN to access an existing wired network, allowing wireless
users to take advantage of the wired networks resources,
such as Internet, email, file transfer, and printer sharing.
Infrastructure networking has the following advantages over
ad-hoc networking:
Extended range: each wireless LAN computer within the
range of the access point can communicate with other
wireless LAN computers within range of the access point.
Roaming: the access point enables a wireless LAN computer
to move through a building and still be connected to the LAN.
Wired to wireless LAN connectivity: the access point
bridges the gap between wireless LANs and their wired
counterparts.
In the next charter, you will be guided to how to connect the adapter to wireless LAN
10
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
3. Wireless Navigator Installation
Install the Wireless Navigator
The Wireless Navigator Utility is provided to allow user easily to configure the adapter
through any Windows-based PC. This section describes procedures for installing the
Wireless Navigator Utility to PC.
Note!
Please make sure that your PC already has TCP/IP protocol installed. If not, please
contact your administrator for details if you have problems of setting up this TCP/IP
protocol in your PC.
Note!
Even your adapter is not connected with PC, but other Ethernet device, such as
printer server. You still can install the Wireless Navigator in any PC located in the
same IP subnet with the adapter. This utility can search the adapter via both wired
and wireless Ethernet so that you still manage the adapter remotely.
Step 1: Insert the installation CD-ROM into the CD-ROM drive. Run SETUP.EXE program
on the CD-ROM. The following window will be shown automatically.
11
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Step 2: After InstallShield Wizard preparation finished, the following window will be shown.
Click the Next button to continue.
Step 3: Key in your User Name and Company Name, and click Next button to continue.
12
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Step 4: The screen will show you the default destination chosen by the utility. If you want to
install the Wireless Navigator in another location, click the Browse button and select
an alternate destination. Click the Next button, when you are ready to continue. The
setup program will then begin to install the programs into the destination folder.
Step 5: The screen will show you the Program Folder that the utility will use. You may type
a new folder name to create a new program folder, or select one from the existing
folder list, and click Next button to continue.
Step 6: The Wireless Navigator has been installed now. Please click the Finish button to
13
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
complete installation.
Note!
To remove Wireless Navigator Utility, click the Start button, and select Programs,
Wireless Navigator, and Uninstall, and then follow the instruction on screen.
14
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
Startup and Login
Follow the procedures below to startup Wireless Navigator and connect to the adapter.
Before you start the following procedures, please be sure that all the cables are well
connected between PC and adapter, and your wireless LAN network is working. The utility
will automatically search the adapter connected with the PC
1. Refer to previous section " Install the Wireless Navigator to your PC" in order to
startup the configuration.
2. Click Start and select Programs, Wireless Navigator and then Wireless Navigator. Or,
just double-click the Wireless Navigator icon on your desktop screen.
3. The Wireless Navigator starts up, and searches the adapter.
15
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
4. The utility will show the adapter found and other wireless devices found in the same
network, where your PC is located.
Note!
If the adapter is not shown in the list, please make sure all the cables are well
connected.
5. Double-click on the adapter, then you will access into its built-in web server, and it will
show as below. Then directly click OK button. (
Note!
).
If you cannot access into adapter’s built-in web server, please make sure if
your PC now is in the same subnet with adapter. Please use right-click of
mouse to click on the adapter listed in Wireless Navigator. “Set IP address”
option will pop out, and then change IP address of AP to the same subnet as
your PC.
16
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
6.
Now you have entered the built-in web server of this adapter, and you can start
configuration procedures described in the next character.
17
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
4. Configuring the Ethernet Adapter
The Info Tab
(Connected with wireless LAN)
SSID: displays current SSID this
adapter uses.
If the adapter found no AP or any
other ad-hoc device, then SSID will
show “non-spec” . Please make
sure that your wireless LAN is
working properly under the effective
reach range of the adapter
Channel: displays the channel that
the adapter uses now.
(NOT Connected with any wireless LAN)
BSSID: displays MAC address of the
AP that the adapter is connecting
with.
Transmission Rate: the transfer
data rate that the adapter is using in
wireless LAN
Link Quality (%): displays the
wireless LAN connection integrity
when connected to an AP.
MAC address: displays the unique
serial number burned into the
adapter that identifies itself from
other Ethernet devices.
IP address: displays the adapter’s
current IP address assigned by AP
or router.
Firmware Revision: displays the
adapter’s current firmware version
Results of the most recent scan:
displays the recent scan over the
wireless LAN, and information of the
found and reachable APs will be
listed
When you re-load the web page, the
result will be updated once again.
18
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
The Wireless Tab
Operating Mode: lets you select the
network scenarios, either Ad-Hoc or
Infrastructure. Default setting is
“Infrastructure”
SSID: lets you set the Service Set
Identifications:
Default SSID is “Any”. When set to
any, the adapter is allowed access to
any nearby AP.
Channel: enables you to select a
transmission channel.
Transmission Rate: displays a list
of transfer rates.
Access point density: enables you
to set the relative number of access
points near the GW-EN11H. Use this
setting to reduce channel overlap
and interference:
• Low: 1-2 nearby APs
• Medium: 3-4 nearby APs
• High: 5 or more nearby APs
When connected in an infrastructure
or ad-hoc mode, a list of nearby APs
or peers is displayed at the bottom of
the Info screen. When you re-load
the web page, the list will be
updated.
WEP enabled: Allows you to enable
or disable Wired Equivalency Privacy
(WEP) for encryption, with either 64or 128-bit encryption.
WEP key length: Enables you to
choose either a 64- or 128-bit
encryption scheme. Be sure that
the adapter’s WEP key must be the
same as the AP’s, otherwise adapter
still can not communicate with
wireless LAN.
Note: Some APs do not support 128-bit
encryption
19
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
The Wireless Tab (Continued)
WEP key 1 ~ 4: Enables you to
create an encryption scheme for
Wireless LAN transmissions.
Manually enter a set of values for
each key.
For 64-bit WEP encryption, a key of
10 hexadecimal characters in length
must be filled in.
For 128-bit WEP encryption, a key of
26 hexadecimal characters in length
must be filled in.. Be sure that the
key in the AP shall be the same as in
adapter, otherwise the
communication will not work.
Note: 128-bit encryption requires
more system resources than 64-bit
encryption. Use 64-bit encryption for
better performance.
WEP key to use: sets which WEP
key (1 ~ 4) to use when sending
data. To connect to a Wi-Fi
compliant wireless device, key #1
must be selected.
Note: The receiver must use the
same key.
Deny unencrypted data: when
checked, prevents reception of any
unencrypted data.
Shared key authentication: the
adapter uses two authentication
modes:
Note!
•
Checked – Shared key.
•
Unchecked – Open key..
You may need to reboot the adapter, and then re-load the page to see
any new settings.
20
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
The Server Tab
IP Address Mode: Select “Static” or
“DHCP” mode. For “Static” mode,
the IP address settings are given by
user. For “DHCP” mode, IP settings
will be overridden by a DHCP server
on your network. The default setting
is “Static”
IP Address: The static IP address
you want to assign to the adapter.
The default value is “192.168.1.100”.
IP Subnet: The subnet mask you
want to assign for the adapter. The
default value is “255.255.255.0”.
IP Gateway: The gateway you want
to assign for the adapter. The default
value is “192.168.1.1”.
Allow upgrade uploads: Check the
box, and then it is allowed to
upgrade firmware.
Note!
You may need to reboot the adapter, and then re-load the page to see
any new settings.
The Admin Tab
Change password: Default
password is “admin”. For security
concerns, please change it after
finish the configuration.
Reboot Adapter: When any setting
was changed, the adapter MUST be
reboot so that the change can be
confirmed.
Reset to factory defaults: This
option will ERASE all the current
settings, and restore to the factory
default settings.
Note!
You may need to reboot the adapter, and then re-load the page to see
any new settings.
21
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
The Help Tab
HELP: Displays the explanations of each setting shown in above seven tabs.
Please click those hyperlinks in right side, and then it will show you the brief
explanation of each setting.
22
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
6. FAQ & Troubleshooting
This chapter provides solutions to problems usually encountered during the installation and
operation of the Wireless Access Point. Please refer to the following descriptions to solve
the problems. If you can’t find an answer here, please contact your dealer for further
advices.
Q1: My PC can’t locate the Wireless Ethernet adapter. How to check the
problem?
A: Please follow the procedures below:
„
Check if the Ethernet cable is well connected.
„
Check if the IP addresses of your PC and Wireless Ethernet adapter both are on
the same IP network. If not, you may use Wireless Navigator to set up adapter’s
IP address, or change your PC’s IP address.
Q2: My adapter cannot communicate with Wireless Access Point. How to
check the problem?
A: Please follow the procedures below:
„
Check if you can use Wireless Navigator utility to access to the adapter first. If not,
please go through the procedure of Q1.
„
Check if the adapter is set to Infrastructure correctly.
„
Check if the SSID of your adapter is the same as AP’s. If not, please set it the
same as the SSID of AP’s.
„
Check if the WEP is enabled either in your adapter or access point. If yes, please
make sure that your adapter and the Wireless Access Point both have the same
setting for WEP, such as the key tables must match.
„
At last, please check if radio interference is causing a problem; see if connection
is possible when close to the Wireless Access Point. Remember that the
connection range can be as short as 100 feet in poor environment.
Q3: The Wireless connection speed is very slow. How to improve the
problem?
A: The wireless system will connect at the highest possible speed, depending on the
distance and the environment condition. To obtain the highest possible connection speed,
you have to try to adjust the Ethernet adapter’s location and its antenna’s direction. If you
find the interference is the problem, changing to another channel may show the
23
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
improvement.
Q4: Can I run an application from a remote computer over the wireless
network?
A: This will depend on whether or not the application is designed to be used over a network.
Consult the application’s user guide to determine if it supports operation over a network.
Q5: Can I play computer games with other members of the wireless network?
A: Yes, as long as the game supports multiple players over a LAN (local area network).
Refer to the game’s user guide for more information.
Q6: What is the IEEE 802.11b standard?
A: The IEEE 802.11b Wireless LAN standards subcommittee, which is formulating a
standard for the industry. The objective is to enable wireless LAN hardware from different
manufacturers to communicate.
Q7: What’s Ad-hoc?
A: An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter, connected
as an independent wireless LAN. Ad-hoc wireless LAN is applicable at a departmental scale
for a branch or SOHO operation.
Q8: What is Infrastructure?
A: An integrated wireless and wired LAN is called an Infrastructure configuration.
Infrastructure is applicable to enterprise scale for wireless access to central database, or
wireless application for mobile workers.
Q9: What is Roaming?
A: Roaming is the ability of a portable computer user to communicate continuously while
moving freely throughout an area greater than that covered by a single Wireless Network
Access Point. Before using the roaming function, the workstation must make sure that it is
the same SSID with the Wireless Access Point of dedicated coverage area.
Q10: What is Spread Spectrum?
A: Spread Spectrum technology is a wideband radio frequency technique developed by the
military for use in reliable, secure, mission-critical communications systems. It is designed
to trade off bandwidth efficiency for reliability, integrity, and security. In the other words,
more bandwidth is consumed than in the case of narrowband transmission, but the trade off
produces a signal that is, in effect, louder and thus easier to detect, provided that the
24
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver
is not turned to the right frequency, a spread-spectrum signal looks like background noise.
There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency
Hopping Spread Spectrum (FHSS).
Q11: What is WEP?
A: WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit or 128-bit
as described in the IEEE 802.11 standard.
7. Product Specifications
This chapter describes the specifications of the product and the LAN port connector.
Wireless LAN Interface
Standards
IEEE 802.11/11b Compliant
Antenna
Chip antenna
Frequency Range
2.4 2.4835GHz ( Industrial Scientific Medical Band )
DSSS - Direct Sequence Spread Spectrum
Data Transmission Rate
11Mbps / 5.5Mbps / 2Mbps / 1Mbps Auto Fall-Back
Access Mode
Infrastructure mode
Ad-hoc mode
Data Security
Provides both 64-bit & 128-bit WEP Encryption
Output Power
15.7 ~17 dBm
Receiving Sensitivity
25
GeoWave GW-EN11H Wireless Ethernet Adapter User's Manual
-82dBm Min.
Roaming
IEEE 802.11 Compliant
Channels
11 Channels (US, Canada)
13 Channels (Europe)
Coverage Area
Indoors:
up to 50M (165 ft.) @11Mbps
up to 80M (265 ft.) @5.5 Mbps or lower
Outdoors:
up to 150M (500 ft.) @11 Mbps
up to 300M (1000 ft.) @5.5 Mbps or lower
(Depending on environment)
Operating Environment
Operating Temperature: 0oC to 50oC degree
Storage Temperature: –25oC to 70oC degree
Humidity 10% to 90% non-condensing
26