Download Marshall electronic V-R84DP-2SDI User's Manual
Transcript
10 Switch Settings, Adjustments and Indicators Marshall Electronics 1910 East Maple Ave. El Segundo, CA 90245 Tel.: 800-800-6608 • 310-333-0606 Fax: 310-333-0688 www.LCDRacks.com Email: [email protected] Power On/Off switch Illuminates red when system power is present Illuminates Green when monitor is ON Image Adjustment Controls Screen aspect ratio switch 4:3 or 16:9 selector and indicators SDI signal selector switches Illuminates when active. Signal format will be displayed via OSD Pixel to Pixel On/Off Lights when active Blue Gun On/Off Lights when active 11 4:3 Aspect 16:9 Aspect Pixel to Pixel Function (Under scan) As the native LCD display is 800 pixels wide by 600 pixels high, it is necessary to change the size of the image to fill the whole screen. Pixel to Pixel mode bypasses the enlargement or scaling function and displays the native incoming format. For 525-NTSC based images, pixel to pixel will appear as a 480x640 (4:3 aspect) or 480x720 (16:9 aspect) display. For 625-PAL based images, pixel to pixel will appear as a 576x640 (4:3 aspect) or 576x720 (16:9 aspect) display. V-R84DP-2SDI Users Guide 12 Menu Functions Turn On/Off with Menu button. Use Up (P-P), Dn (Blue), and Select (Ratio) for menu navigation functions. Color Temperature – Select D65 or User. User mode will automatically be turned on if Gain or Bias are adjusted. Adj Color Gain – Select to adjust RGB gains. Adj Color Bias – Select to adjust RGB bias OSD – Toggle OSD on/off. Version Number – Display only Gain Adjustment Press Press Press Press Press Up (P-P), Dn (Blue), to navigate. Select (Ratio) to activate. Select to toggle R, G, or B Up, Dn, to change value. Menu to exit Bias Adjustment Press Press Press Press Press Up (P-P), Dn (Blue), to navigate. Select (Ratio) to activate. Select to toggle R, G, or B Up, Dn, to change value. Menu to exit Chart legend: Left Line = Increase of gain Center Line = D65 (Default) Right Line = Decrease of gain Chart legend: Right Line = Increase of Bias Center Line = D65 (Default) Left Line = Decrease of Bias OSD Adjustment Press Up (P-P), Dn (Blue), to navigate. Press Select (Ratio) to toggle OSD On/Off Product Overview Features Standard Accessories Optional Accessories Electrical Specifications Mechanical Specifications 13 Warranty Marshall Electronics warranties to the first consumer, that this V-R84DP-2SDI portable monitor will, under normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date. This warranty is extended to the first consumer only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right, not to honor the warranty set forth above. Therefore, labor and parts may be charged to you. This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve products and product features, specifications may change without notice. Faceplate Cleaning Operational Setup Input Connectors Switch Settings, Adjustments and Indicators Pixel to Pixel Function Menu Functions Warranty 1 2 3 4 5 6 7 8 9 10 11 12 13 Product Overview 1 Our V-R84DP-2SDI is a direct replacement for 8 and 9-inch CRTs used in broadcast and professional video applications. This cost effective model includes our Award Wining Digital TFT-Megapixel™ system for the LCD screen with 1.44 million pixels plus our HyperProcess™ of interlace images to produce the smoothest motion available on an LCD/TFT. Standard features include V-Mount battery adapter, 4 pin XLR power jack, and optical grade polycarbonate screen protection. Video is scaled to fit on screen in the highest resolution using a state of the art LSI that incorporates 6x6 pixel interpolation with precision Gamma correction and Match Color Conversion™ to product the best images available. Features 2 210 Plastic Cleaner & Polish and 210 Plus Cleaner 20/20 Plastic-Cleaner Sumner Laboratories Craftics, Inc. 186 Lincoln Street Boston, MA 02111 617-542-8656 / Fax: 617-482-9001 PO Box 91930 Albuquerque, NM 87199 (505) 338-0005 Crystalclean Plexus Plastic Cleaner Discovery Plastics Plexus 638 Lindero Canyon Rd. #371 Agoura, CA 91301 800-405-6495 Fax: 818-879-0697 TFT-MegaPixel™ Display 800x600 Dots (1.44 million pixels) Capable of displaying more than 800 TV Lines resolution. The composite video signals are internally up converted to High Definition. All signals remain completely digital to provide the most exact images available. 3700 Western Way, NE Millersburg, OR 97231 541-926-2900 / Fax: 541-967-8441 www.discoveryplastics.com Standard Inputs 2 SDI with Auto Detect of 525/625 formats (BNC) (SMPTE259M) (ITU-R-BT601) Scotch-Brite High Performance Cloth NOVUS #1 Plastic Clean and Shine Durable metal enclosure Protection for all connections and controls with strategically placed ventilation for use in harsh environments 3M Stationery & Office Supplies Div. 3M Center NOVUS, Inc. 12800 Highway 13 South, Suite 500 Savage, MN 55378 800-548-6872 ext.451 Fax: 952-946-0435 Protective Screen Cover Optical grade polycarbonate screen cover with Antireflective/Antiglare coating HyperProcess™ Display interlace images without smearing or sacrifice of temporal resolution with our proprietary interpolation algorithms. Images are then displayed at a sample rate equal to the frame rate. St. Paul, MN 55144-1000 877-362-5684 Fax: 651-733-0382 www.mmm.com Memory Function Adjustment Settings Memory stored on shutdown and recalled when power is applied The Simco Industrial Static Control Exair Corporation MatchColor Conversion™ Factory programmed to closely match typical SMPTE/EBU CIE color metric and color temperature specifications. This model is adjusted for D-65 color temperature and 62% SMPTE color gamut Color Temp Adjustment User control for gain and bias of Red, Green, and Blue colors Blue Screen Use for adjustment to SMPTE color Bars 1250 Century Circle North Cincinnati, OH 45246-3309 513-671-3322 Fax : 513-671-3363 www.exair.com OSD On screen display of Format and Ratio An Illinois Tool Works Co. 2257 North Penn Road Hatfield, PA 19440-1998 800-203-3419 215-822-2171 Fax: 215-822-3795 www.simco.biz Pixel to Pixel™ Scale process bypass to display native pixel inputs. Also functions as Underscan 50,000 hour backlight life Backlights are the most common failure on a TFT/LCD monitor. This backlight system has an MTBF of 5 years and uses specially designed lamps to provide brighter images. Tally (DB-15) Three LEDs (Red, Green, Amber) produce 7 different tally indications 3 Standard Accessories Accessories Supplied with the V-R84DP-2SDI • Users manual • “Brick” type 12vdc power supply with 4 Pin Female XLR connector 4 2 Recommended Anti-Static Cleaners and Polishes • “V” Mount battery adapter • ¼”-20 mounting plate Optional Accessories 8 Operational Setup 1. Unpack the V-R84DP-2SDI and accompanying power supply. Physically inspect for any damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606. 2. Connect required cables for signal input and output. Please note that power must be applied to the V-R84DP-2SDI for the video outputs to be activated. All BNC connectors should be rated for 75Ω. 3. Plug the power supply into the A.C. source. Please note that power can be supplied from a variety of DC sources, such as batteries or Vehicle power. Input power range is 10.4 to 16.8 Volt D.C. In operation, the V-R84DP-2SDI will draw approx. 1. amp. Attach 4 Pin XLR power connection from V-PS12-V-5 power supply to the back of the unit. 4. Turn on the V-R84DP-2SDI by depressing the power switch located on the front of the unit. Input Connectors Stand V-LCD4-ST Use for table top mount Sun Hood V-H900 Use for viewing in bright lighting or outdoors Battery and External Power can not be used simultaneously Power Adapter Cable V-PAC-D Use with Anton Bauer D-type connection V-Mount Battery Adapter See Optional Accessory section for a selection of batteries Power Adapter Cable V-PAC-XLR Use with 4 Pin XLR connections Protective Carry Case TBD Manufactured by Storm Case V-R84DP-2SDI Users Guide 9 * Tally lamps active when connected to ground Marshall Electronics 5 Optional Accessories (continued) Battery Adapter V-DV-PWR1 Uses 2 Sony DVCam/HDV FP-Type batteries. When used with monitor power supply, can charge batteries plus operate monitor V-mount to Anton Bauer adapter V-ABA-01 Use to power Marshall Electronics monitors that have VMount plate with Anton Bauer Gold Mount battery. Sequential 2 channel charger IDX-VL-2Plus 2-channel sequential charger with a built-in 60W power supply. Charges 2 ENDURA E series batteries in fewer than 5 hours. One 10’ XLR cable included. Weighs only 2 lbs Sequential 4 channel charger IDX-VL-4 Economically charges 4 ENDURA E series batteries in under 6 hours using Full Power Charge (FPC) method Simultaneous 4 channel charger IDX-VL-4S Charges 4 ENDURA E series batteries in 2.5 hours or less 55 W Lithium Battery IDX-E7S V-Mount battery pack with 3 LED power Indicator 55 W Lithium Battery with Power Link IDX-E7 V-Mount Battery Pack with PowerLink includes accurate Power Status Display and supports Digi-View 82 W Lithium Battery IDX-E10S V-Mount battery pack with 3 LED power Indicator 82 W Lithium Battery with Power Link IDX-E10 V-Mount Battery Pack with PowerLink includes accurate Power Status Display and supports Digi-View Digital to Analog Converter BC-0301-10 Converts SDI to analog Composite Mounting Plate Cleaning Wipes Attaches to any side for mount to ¼-20 threaded component V-HWP-K Package of 10 non-toxic, antistatic, alcohol and ammonia free cleaning wipes. Marshall Electronics 3 5 Electrical Specifications Display (Viewing Area) Screen Aspect Resolution (RGB Dots) Viewing Angles Contrast Ratio Dot Pitch Pixel Response Backlight Type / Life Brightness LCD Screen Treatments Protective Screen Estimated MTBF System Inputs Active Outputs Color temperature Color Gamut Luma Linearity Power Required Power Consumption Operating Temperature Storage Temperature Compliance RoHS WEEE/Environmental 8.4 Inch diagonal (170.4mm w x 127.8mm h) 4:3/16:9 switchable 800H×RGB×600V (1.44 million pixels) 160° with protective screen and treatment (130°H x 120°V native) 500:1 .213mm square pixel 10ms rise/25ms fall Field Replaceable CCFL (50,000 hour half life) 500 cd/m² Anti Reflection, Anti Glare, Hardcoat 0.118” (3mm) thick Optical Grade Polycarbonate with Anti-Glare and Anti-Abrasion coatings. (600 Cheesecloth mil-M-13508C) 5 years of 24/7/365 operation NTSC/PAL auto recognition 2 SDI (BNC) Self Terminating (SMPTE-259M) (ITU-BT-R601) 1 SDI of on screen video (BNC) Available when power is applied D65 (6500° Kelvin) SMPTE-C/EBU Typical +/- 3% with 5 ire increments (0 to 10 ire) 10.4 to 16.8 VDC Approx. 15 watt nominal 32°F to 120°F (0°c to 50°c) -4°F to 120°F (-20°c to 50°c) ₠, FCC-Class A, ANSI-63.4 (Certificates on file) Do not dispose. Return to Manufacturer or Authorized Recycle Facility 6 Mechanical Specifications Dimensions Approx. Weight Power Consumption 9”w x 6.875” h x 2.5” d (228.6mm x 174.6mm x 38.1mm) 3.3 lbs 14-10 VDC, 15 Watt nominal (Universal Voltage 5.0Amps max - UL Class 2 supply included) 7 Faceplate Cleaning Faceplate Cleaning When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro fiber cloth. Do not use paper towels. Paper towel fibers are coarse and may scratch the surface of the Polycarbonate faceplate. Paper towels may also leave streaks on the surface. Antistatic and fingerprint resistant cleaning agents are recommended. Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pressure. Rinse with clean water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade of hexane, aliphatic naphtha, or kerosene. These solvents may be obtained at a paint or hardware store and should be used in accordance with manufacturer’s recommendations. DO NOT USE: window cleaning sprays, kitchen scouring compounds or solvents such as acetone, gasoline, benzene, alcohol, carbon tetrachloride, or lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing small surface cracks called “crazing.” Faceplate Dusting Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the surface. Neutralizing static electricity effects by using recommended cleaning and polishing practice. Faceplate Polishing Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft clean cloth and polish lightly with cotton flannel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract dust particles Marking on the Faceplate Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent. 4 V-R84DP-2SDI Users Guide