Download Lightolier S:6497 User's Manual
Transcript
I /’- INSTRUCTION INSTRUCTIONS FRAMING FOR AllACHING PROJECTOR MR-16 “ IS:6497 ACCESSORY R0590 FOR USE WITH LYTESPAN’) TRACK SYSTEMS ONLY. READ AND UNDERSTAND THESE INSTRUCTIONS SHEET NO Page 1 of 2 BEFORE INSTALLING FIXTURE. This fixture is intended for installation in accordance with the National Electrical Code and local re ulations. To assure full compliance with local codes and regulations, check with your local electrical inspector be ?ore installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Retain these instructions for maintenance reference. 1 Turn the fixtures OFF and allow the LAMP to cool before attaching the PROJECTER ACCESSORY. MR.16 LAMP 2, Remove LAM PHOLDER ASSEMBL.Y from fixture. See Fig. 1. Note. Style of Iampholder ~sseinbly will vary from fixture to fixture. 3. Flernove MR-16 lAMP and GLASS LAMP GL!ARD from lAMPHOLDER ASSEMBLY. LAMPHOLDER ASSEMBLY 4. Remove the INNER RING from PROJECTOR ACCESSORY by backing out the (2) LOCKING SCREWS (see Fig. 2). GIASS LAMP GUAR FIG. 5. Slip the INNER RING through the LAMP HOLDER ASSEMBLY making sure the notches in INNER RING clear the springs or inner ribs. 6. Slide the PROJECTOR ACCESSORY over the LAMP HOLDER ASSEMBLY. When properly positioned, hole in INNER RING will be aligned to accept LOCKING SCREWS. NOTCHES .,, .. ---A INNER RING Da 7. Install LOCKING SCREWS half-way. Turn the PROJECTOR ACCESSORY clockwise until it is tight against the LAMP HOLDER .4SSEMBLY. Tighten locking screws. u 8. Replace the GLASS LAMP GUARD, install the proper wattage LAMP, and attach the LAMP ASSEMBLY with PROJECTOR ACCESSORY back on the fixture (see Fig. 3), & w /, /“” /-’___--- 9. Turn the fixture ON and adjust the SHUTTER BLADES to frame object and focus the LENS for the sharpest beam. ~ ‘iv SHUTTER LENS 1 .“--,,, -.,-. *. LAMP HOLDER ASSEMBLY – “- -- PROJECTOR ACCESSORY LENS I FIG. 2 FIG. 3 WARNING: LAMP MANUFA~URERS REQUIRE THE GIASS LAMP GUARD BE IN PLACE BEFORE ENERGIZING LAMP, AND THAT GREAT CARE SHOULD BE TAKEN THAT LAMP IS FULLY COOLED BEFORE REIAMPING. NOTE: This framing projector accessory is for use on specific Llghtolier ~R16 fixtures only. See fixture catalog for complete listing. — MR-16 FRAMING PROJECTOR ACCESSORY lLLUMINAllON ON VERTKAL PLANE ShutterBladesSet ForMaximumBeamCoinage -— A) 30“ 4~ @ 30“ 45“ 60° 30“Q5:6@ 30“ 45“ 60 “ 3~ 45:~ 3~5:_60: 30“ 45“ 60 “ 12” 1~_2_~. 20” 30” 35” 29= 42” 4~ 37” 54” 62” 46” 66” 75” 54” 78” 88” 6~;—~fiijI~-” _Lennth(L) 16”22”44”27”37”70” 39_”_~l:97” 50”66”123-61” 81”150”72”95”176 84” l10”20Z’_ _“~ ZO:_3~.”_5Y 26“ 44“ !B.: 33“ 55“ 83: 3.9= W “ AIZ:.Z7:_Llfj“152 “ ?8.”K. :IE:fzf-~=:7:E FCWExw@?!lI?l_!? ‘l?I 61_20 65 -———.-——— 34 11 3L20... ?_. 26 14 5. ~8__g0 ___3@ 7 2 12 ?sww14m~wc6811 332 —— 951234 119 37 I 117 61 20 70 — 37 -—. -.—. — 4.? .?~_.8 ~3_ lg. !..i?j.ds!!jj —E-.. .- ——— b?ngth(L) to ttw pointthat FCdropsto 10% of maximum lLLUMINA~N ON HORIZONTALPLANE —