Download Genius Speaker System 31730952100 User's Manual
Transcript
Service Guide SP-i160 SERVICE GUIDE KYESYSTEMS CORP. SP-i160 Version : 1.0 Page 1 of 14 Service Guide SP-i160 Version : 1.0 Revision History Version Date 1.0 15/01/2010 Version : 1.0 Change Page 2 of 14 Service Guide SP-i160 Table of Contents Revision History …………………………………………………………………….2 Table of Contents ……………….……………………………………………………3 Getting Started ……………………………………………………………………….4 Conventions Used in this Guide ……………………….…..………………....4 Safety Precautions …….……………………………………………………..4 Chapter 1. How to Handle Defective Returns……………………………………..5 1.1 Overview …………………………………………………………..5 1.2 Problems …………………………………………………………...6 1.2.1 No sound (Line in jack no function) …………..…7 1.2.2 Power LED (indicator) no light……...………....…8 1.2.3 Li-ION battery can’t charge.…..….…………….8 Chapter 2. Specifications ………………………………………………………….9 Chapter 3. Block Diagram ……………………………………………………….10 Chapter 4. Exploded View ……………………………………………………….11 Chapter 5. Part List ………………………………………………………………12 Chapter 6. Schematic Diagram …………………………………………………..13 Chapter 7. Important Notes ………………………………………………………14 7.1 Packing Requirement for Sending the PCB Assembly by Post …..14 7.2 Short of Spare Parts while Repairing a Speaker System …………14 Version : 1.0 Page 3 of 14 Service Guide SP-i160 Getting Started Conventions Used in this Guide Pay Special Attention : Instructions that are important to remember and may prevent mistakes . Caution : Information that, if not followed, may result in damage to the product . Safety Precautions The following precautions should be observed in handling the speaker Described in this guide : Place the speakers on a flat, level and stable surface. Do not place the speakers in environments subject to mist, smoke, vibration, excessive dust, salty or greasy air, or other corrosive gases and fumes. Do not drop or jolt the speakers. Do not allow anything to drop into the subwoofer case through its ventilator, as it could result in fatal electric shock or fire . Place the unit far enough from other equipments for good heat dissipation . Disconnect the AC power cord from the AC outlet before performing any maintenance on the speakers . Do not perform any maintenance with wet hand . Prevent foreign substances, such as water, other liquids or chemicals , From entering the speakers while performing maintenance procedures on the speakers . Version : 1.0 Page 4 of 14 Service Guide SP-i160 Chapter 1. How to Handle Defective Returns 1.1 Overview Receiving Defective speakers from Customers Function NG __ __ Analyzing possible malfunction causes Function NG Deciding & proceeding the rectification methods Function OK Replace necessary defective parts Function OK Return the speakers with proper repackaging to customers Version : 1.0 Page 5 of 14 Service Guide SP-i160 1.2 Problems Item Problem Description 1.2.1 No sound (Line in jack no function) 1.2.2 Power LED (indicator) no light 1.2.3 Li-ION battery can’t charge Version : 1.0 Page 6 of 14 Service Guide SP-i160 Attention Please follow the numbered sequence marked within parenthesis given in individual Flow chat, in that this is the best-recommended sequence to rectify the problems. 1.2.1 One or more channels no sound (Line in jack no function) Problem No sound Analyzer and Identify the Causes Solutions Broken or short circuit Defective U1, U4 Check solder points on PCB Check and Replace defective IC Version : 1.0 Page 7 of 14 Speaker cable dis-connect , JACK1 or JACK2 defective or speaker damaged Re-connect speaker cable or replace defective speaker(s) Service Guide 1.2.2 SP-i160 Power LED (indicator) no light Power LED (indicator) no light Problem Analyzer and Identify the Causes Power switch or LED Defective defective J1 Re-solder or replace defective component(s) Solutions 1.2.3 The Li-ION Battery can’t charge The Li-ION battery can’t charge Problem Analyzer and Identify the Causes Solutions U2 Battery Broken or short circuit Check solder points on PCB Check and Replace defective components Version : 1.0 Page 8 of 14 Service Guide Chapter 2. SP-i160 Specifications NO. Description Unit Specifications 1 Out Power at THD 10% W ≧ 1.8 2 Sensitivity mV 600 ± 50 3 Freq. Response (1KHz -3dB) Hz 180~20K ± 10% 4 Separation dB ≧ 40 5 S/N ratio dB ≧ 80 6 Hum & Noise mV ≦ 2 (Vol.: max) Version : 1.0 Page 9 of 14 Service Guide Chapter 3. — ► Audio SP-i160 Block Diagram Tone Volume Control Control — ► L.CH Speaker A i Power Ac in Conditioner Version : 1.0 Page 10 of 14 Service Guide Chapter 4. SP-i160 Exploded View Version : 1.0 Page 11 of 14 Service Guide Chapter 5. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 SP-i160 Part List DESCRIPTION Qty UNIT 1 PC Loud Speaker 1.25" 4 ohm 1~2W 1 PC FSA510112-1402 Rubber Pad(Φ4.8 X 2.3T), SP-i160 3 PC 15400009100 PCBA, SP-i160 1 PC ASL507003-0026 IC, JRC NJM2761 1 PC IC, T1 TPA2031D1 1 Set IC, LN,LN2054 1 PC BATTERY, SP-i160 1 PC FBY508037-0003 FANNEL BAG SP-i160 1 PC 12290076100 S/N LABEL SP-i160 2 PC 12061017100 1 PC INNER TRAY SP-i160 1 PC 12150227100 PET BOX, SP-i160 1 PC 12140001100 Anti-fake Label ( on Gift Box ) 1 PC 12061993100 1/50 PC 12100465100 RS,ASM,SP-I160,HOST,BLACK RS,ASM,SP-I160,HOST,WHITE 31730952100 CARD SP-i160 / B CARD SP-i160 / W Carton, SP-i160 Version : 1.0 Part No. 31730952101 RCI203101-0001 12020186100 Page 12 of 14 12020187100 Service Guide Chapter 6. SP-i160 Schematic Diagram Pls refer to next page Version : 1.0 Page 13 of 14 1 2 4 3 D D J1 L1 BEAD120 5V R9 BEAD120 R10 2K BAT ON Q1 NC C3 100uF C16 151 C2 104 4 C13 151 Vcc R12 2K LD1 RED CHRG GND 1 2 C LD2 BLUE U2 LN2054 Vcc 5 1 2 3 4 3 BAT 5 PROG C14 NC R11 4.7K BT1 BATTERY U1 TPA2031D1 R6 100K Shut_DN B1 C1 10uF 223 224 105 5 R5 C4 V+ Out1 IN1 INT C23 224 473 R8 8K2 GND C22 224 105 IN+ ShutDN VoGND 104 C3 So+ L2 A3 BEAD120 C8 S1 C9 270P B3 C10 240k 471 R4 68k C 270P SPK 270P L3 BEAD120 So- 68k C6 473 GND OUT2 IN2 C20 Vo+ 10uF Vcc R3 240k C7 471 B 10 9 8 SW Sense 7 6 R2 1k C5 IN- B2 C12 R1 U4 IC-NJM2761 R7 3.6k C2 PVDD C11 A2 224 Vref A1 1 C21 3 C17 2 C18 4 C19 B C1 Vcc GNDGND VDD GND CN4P-USB S1 SW-SPDT USB ON GND R13 8K2 Title A Size A4 Date: File: 1 2 3 A Number Revision SP-i160 21-Jan-2010 E:\MODEL INFO\KYE\F4\Mr Pai.ddb VER090820 Sheet of Drawn By: 4 Service Guide Chapter 7. SP-i160 Important Notes 7.1 Packing Requirement for Sending the PCB Assembly by Post PCB assembly is a kind of sophisticated electronic circuit board. Well packing will be required when sending them by post. * Some sophisticated IC components are mounted on the PCB assembly, hence it is necessary to pack each PCB assembly with a separate static protecting bag, in order to avoid static electricity. * Reliable external packing is also very important when sending PCB assembly by post, in that it would avoid unnecessarily lost or damage. 7.2 Short of Spare Parts while Repairing a Speaker System If you are short of spare parts when you have some speaker systems waiting to be repaired, it would be recommended to take the necessary parts form one speaker system, so that you may have the as many speaker systems. Version : 1.0 Page 14 of 14