Download ARRI WRC-1 User's Manual

Transcript
WRC-1
Wireless Remote Control Instruction Manual
As of: June 2000
ALL ARTWORK, PICTURES AND TEXTS ARE COVERED BY OUR COPY-RIGHT.
THEY MUST NOT BE COPIED FOR REPRODUCTION (E.G. ON CD-ROM DISKS OR INTERNET-SITES) OR USED IN THEIR ENTIRE FORM OR IN EXCERPTS WITHOUT OUR PREVIOUS WRITTEN AGREEMENT.
IF YOU ARE DOWNLOADING PDF-FILES FROM OUR INTERNET HOME-PAGE FOR YOUR PERSONAL USE, MAKE SURE TO CHECK FOR UPDATED VERSIONS.
WE CANNOT
TAKE ANY LIABILITY WHATSOEVER FOR DOWNLOADED FILES, AS TECHNICAL DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
IRIS sliding switch
RUN-LED
WRC/CAM sliding switch
RELEASE button
READY-LED
radio channel
ON button
SEL button
MODE button
SET button
OPEN/PHASE
RAMP button
button
WRC
rotary switch
RF-LED
CAL-LED
CAL button
COMPENSATION
rotary switch
READY-LED
BAT-LED
RUN-LED
RUN button
handwheel
2. Safety Instructions .......................................... 7
Explanation of the Symbols in this Instruction Manual ....... 7
Product specifications ................................................. 7
4. Setup ............................................................... 17
4.1
4.1.1
3. Introduction ...................................................... 9
4.1.2
3.1
Some typical applications .......................... 10
Exposure compensation ............................. 10
Altering the depth of field .......................... 10
Speed ramps ............................................ 11
3.2
3.2.1
3.2.2
3.2.2.1
Functions .................................................. 12
CAM mode ............................................... 12
WRC mode ............................................... 13
Overview of the settings available
with the WRC rotary switch ........................ 14
Overview of the settings available
with the COMPENSATION rotary switch ..... 15
3.2.2.2
4.2
4.2.1
WRC-1 in wireless mode ........................... 17
Required system components ...................... 17
Mounting the WRC-1 on the
Wireless Main Unit (WMU-1) ..................... 18
Attaching the UMC-1 and URM-1
to the camera ........................................... 19
Setup with Iris control ................................ 22
Mounting the CLM-2 motor
with/without console ................................. 22
Contents
1. Contents
WRC-1 in cable mode ............................... 24
Required system components ...................... 24
Mounting the WRC-1 on the
Wireless Handgrip Attachment (WHA-1) .... 24
3
Contents
5. Operation ....................................................... 25
5.5
5.1
5.1.1
5.1.2
Operating modes ...................................... 25
CAM mode ............................................... 25
WRC mode ............................................... 26
5.5.1
5.5.1.1
5.2
Switching on ............................................. 27
5.3
Important instructions ................................ 28
5.4
5.4.1
5.4.2
5.4.2.1
5.4.2.2
Using the menus ........................................ 31
Main menu ............................................... 31
Submenus ................................................. 33
Limit values ............................................... 33
Fixed values .............................................. 33
5.5.1.2
5.5.1.3
5.5.1.4
5.5.1.5
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
5.5.7
4
Controlling the iris
(master value: Iris) ..................................... 37
Assigning the T-stops ................................. 38
Loading iris tables for Zeiss Ultra Primes,
Variable Primes, High-speed,
Standard or user-defined lenses
(‘TBL LOAD’) ............................................. 40
Programming an iris table for other lenses
(‘TBL EDIT’) ............................................... 44
Storing an iris table
(‘TBL STORE’) ............................................ 47
Loading a user-defined iris table
(‘TBL LOAD’) ............................................. 48
Important instructions
for programming the iris of the lens ............ 51
Iris / compensation off .............................. 52
Iris / compensation shutter angle ................ 55
Iris / compensation user ............................ 58
Ramp iris / compensation off ..................... 62
Ramp iris / compensation shutter angle ...... 66
Ramp iris / compensation user ................... 70
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
Controlling the mirror shutter angle
(master value: Shutter angle) ...................... 77
Shutter angle / compensation off ............... 78
Shutter angle / compensation iris ............... 80
Shutter angle / compensation user ............. 84
Ramp shutter angle / compensation off ....... 88
Ramp shutter angle / compensation iris ...... 92
Ramp shutter angle / compensation user .... 96
5.7.8
5.7.9
5.7.10
5.7.11
5.7.12
5.7
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
5.7.6
5.7.7
Controlling the camera speed
(master value: Speed) .............................. 104
Speed /
compensation off .................................... 104
Speed /
compensation iris .................................... 106
Speed /
compensation shutter angle ...................... 110
Speed /
compensation iris and shutter angle 50% .. 113
Speed /
compensation max. iris ............................ 116
Speed /
compensation max. shutter angle ............. 120
Speed /
compensation user .................................. 124
5.7.13
5.7.14
Ramp speed /
compensation off .................................... 128
Ramp speed /
compensation iris .................................... 132
Ramp speed /
compensation shutter angle ...................... 136
Ramp speed /
compensation iris and shutter angle 50% .. 140
Ramp speed /
compensation max. iris ............................ 146
Ramp speed /
compensation max. shutter angle ............. 152
Ramp speed /
compensation user .................................. 158
Contents
5.6
6. Warnings ...................................................... 163
Warnings when programming iris tables ................. 168
5
Contents
6
7. Quick guide ................................................. 171
7.1
Connecting the devices ............................ 171
System components required
for wireless operation .............................. 171
System components required
for cable operation .................................. 171
7.2
7.2.1
7.2.2
Basic operating modes ............................ 172
CAM mode ............................................. 172
WRC mode ............................................. 172
IRIS ON/OFF ......................................... 172
7.3
7.3.1
7.3.2
Operation .............................................. 173
Iris control .............................................. 174
Entering values ....................................... 177
8. Glossary ....................................................... 183
9. ARRI Service ................................................. 185
10. Index ........................................................... 187
• The WRC-1 has been thoroughly tested for quality of
workmanship and operating functions before leaving
the factory.
• To ensure optimal performance, it is essential that you
acquaint yourself with this instruction manual and that
you follow the operating instructions described.
Explanation of the Symbols
in this Instruction Manual
➪ photo indicates objects which are shown in the
photographs or drawings.
• Warnings:
Caution! – means danger of injury
Injury to the user possible
Warning! – means damage to the equipment
possible.
• Assembly and initial operation should only be carried
out by qualified personnel already familiar with the
equipment and the assembly procedures!
• In wet weather the normal safety precautions for
handling electrical equipment should be taken!
Note:
Supplementary instructions,
or improper use is possible.
Safety Instructions
2. Safety Instructions
• Do not use solvents for cleaning!
Product specifications
• Do not loosen any screws which are secured with paint!
• Use only original ARRI spare parts and accessories!
When ordering parts or accessories, or if any questions
should arise, please advise your type of product and
serial number.
• Always return the equipment to an authorised dealer
for repairs!
7
8
The Wireless Remote Control WRC-1 is a handy remote
control unit for use with all of the latest generation of
ARRIFLEX camera models: ARRIFLEX 16SR 3/Advanced,
16SR 3 HS/Advanced, 535, 535B, 435, 435ES
It enables the user to remotely control:
• the camera speed,
• the shutter angle of the mirror shutter, and
• the aperture of the lens (iris),
providing a wide range of compensation options for
constant exposure.
The illuminated LCD provides quick, precise and comprehensive information about all the settings, the status of the
camera and the WRC-1, including all warnings.
The WRC-1 is the perfect addition to the ARRI Wireless
Lens Control System. Connected to the Wireless Main Unit
WMU-1 of the Wireless LCS it enables all functions to be
remotely controlled. The WRC-1 can also be connected to
the camera via cable using the Wireless Handgrip Attachment WHA-1 of the Wireless LCS system. However, the lens
remote-control functions are not available in this mode.
Introduction
3. Introduction
The range of functions offered by the WRC-1 is automatically
adapted to the limits of the camera and the lens control
motor to which it is connected. The large handwheel
permits sensitive adjustment of operational values, and
easy programming of end-stops for user-defined minimum
and maximum values.
9
Typical Applications
10
3.1 Some typical applications
Exposure compensation
Altering the depth of field
Differences in exposure, such as occur when moving from
outdoor to indoor in one take, can be easily, accurately
and repeatedly compensated for using the WRC-1.
A user defined program, which can be repeatedly activated,
is used to control either the iris or the shutter angle of the
mirror shutter – in this case the visible depth of field of the
image does not change.
Intentional adjustment of the depth of field at a constant
camera speed is another option available with the WRC-1.
In this case the mirror shutter angle is adjusted, using the
WRC-1, and the resulting difference in exposure is
automatically compensated with the iris of the lens.
Altering the camera speed also changes the film exposure
time. In order to hold the film exposure constant when
changing the camera speed, either the shutter angle of the
mirror shutter or the aperture of the lens must be adjusted
accordingly. The WRC-1 allows the camera speed to be
changed while simultaneously retaining a constant exposure.
Several different compensation methods can be selected.
Example: the camera ramps up from 24 fps to 48 fps.
Two compensation options are available:
Compensation
fps
None
24
180
5.6
48
180
5.6
24
90
5.6
OK
48
180
5.6
OK
24
180
5.6
OK
48
180
4
OK
Shutter Angle
Aperture
Shutter Angle Aperture
Result
OK
1 T-stop under-exposed
The required compensation type can be simply selected
using the COMPENSATION rotary switch on the WRC-1.
The camera speed can either be adjusted using the
handwheel, or it can be pre-set by programming a speed
ramp, which is activated by pressing the RAMP button.
Note:
Adjusting the iris alters the depth of field.
Adjusting the shutter angle, on the other hand,
does not alter the depth of field. A small shutter
angle and a rapid camera movement, or fastmoving objects, may result in stroboscopic effects.
Typical Applications
Speed ramps
Adjusting the shutter angle when using HMI
light may result in inconsistent film exposure.
11
Functions
3.2 Functions
IRIS sliding switch
The WRC/CAM sliding switch is used to select
the operating mode ➪ photo.
WRC/CAM sliding switch
3.2.1 CAM mode
SEL button
MODE button
OPEN/PHASE-
SET button
RAMP button
button
WRC
rotary switch
handwheel
In CAM mode, the operator can access the same settings
and modes that are directly available on the camera itself.
The display on the WRC-1 shows the same information as
the camera display.
COMPENSATION
rotary switch
The MODE, SEL, SET and RAMP buttons have the same
functions as their respective counterparts on the camera.
A RUN LED is also integrated.
In the CAM mode, the OPEN button on the WRC-1 serves
as the PHASE button on the camera.
In CAM mode the WRC-1 serves purely as a camera
remote control unit, without any wider programming options.
The handwheel, the WRC and the COMPENSATION
rotary switches are without function in this operating mode.
12
The WRC mode offers convenient programming and easy
adjusting of the camera speed, the shutter angle and the
iris of the lens.
Depending on the chosen settings and the compensation
method, different ramp times are possible. The minimum
ramp time is calculated by the WRC-1.
If the iris control is not activated (IRIS sliding switch ‘OFF’),
the OPEN button serves as the PHASE button on the
camera ➪ photo.
Note:
The left rotary switch (WRC) ➪ photo is for selecting
the parameter which is to be changed
(master value; for definition, see Glossary):
• camera speed,
• shutter angle or
• iris.
The right rotary switch (COMPENSATION) ➪ photo
is for setting how the change in exposure caused by the
adjustment is to be compensated for
(slave values; for definition, see Glossary).
The term ‘adjust’ as used in this instruction
manual describes each direct adjustment of a
parameter using the handwheel.
Parallel to this adjustment, the WRC-1 can
automatically compensate the resultant difference
in exposure.
Functions
3.2.2 WRC mode
The term ‘ramp’ describes adjustment actions
which automatically take place over a predefined
period of time, i.e. these actions are not directly
controlled using the handwheel. They run continuously for a predefined period of time after
pressing the RAMP button. Resultant differences
in exposure can also be compensated for.
Example: the WRC rotary switch is set to fps, the COMPENSATION rotary switch is set to Iris. The camera speed is
adjusted with the handwheel, while the WRC-1 automatically
keeps the film exposure constant, adjusting the iris of the
lens.
13
Functions
14
3.2.2.1 Overview of the settings available
with the WRC rotary switch
• fps
In the ‘FPS’ mode the camera speed can be adjusted by
turning the handwheel. The end-stops of the handwheel
can be defined by the user within the limits of the attached
camera model.
(master value: camera speed)
• ramp fps
In the ‘RAMP FPS’ mode the camera speed is changed
from one value to another over a pre-defined period time.
The speed ramp is started by pressing the RAMP button.
(master value: camera speed + ramp duration)
• )
In the ‘ ) ’ mode the mirror shutter angle can be adjusted
by turning the handwheel. The end-stops of the handwheel
can be defined by the user for the required shutter angle
range.
(master value: mirror shutter angle)
• ramp )
In the ‘RAMP ) ’ mode the shutter angle is changed from
one value to another over a pre-defined period time. The
shutter angle ramp is started by pressing the RAMP button.
(master value: mirror shutter angle + ramp duration)
• Iris
In the ‘IRIS’ mode the iris of the lens can be adjusted by
turning the handwheel. The end-stops of the handwheel
can be defined by the user for the required aperture
range.
(master value: iris of the lens)
• ramp Iris
In the ‘RAMP IRIS’ mode the iris of the lens is changed
from one value to another over a pre-defined period time.
The iris ramp is started by pressing the RAMP button.
(master value: iris of the lens + ramp duration)
• off
In the ‘OFF’ position there is no exposure compensation
for the programmed ramp functions or the handwheel
adjustments.
(no slave values)
• Iris
In the ‘IRIS’ position the handwheel adjustments or the programmed ramp functions are compensated for by automatically adjusting the iris of the lens for a constant exposure.
(slave value: iris of the lens)
• )
In the ‘ ) ’ position the handwheel adjustments or the
programmed ramp functions are compensated for by
automatically adjusting the mirror shutter angle for a
constant exposure.
(slave value: mirror shutter angle)
• Iris / ) 50%
In this mode the exposure compensation is divided equally
between the shutter angle of the camera and the iris of
the lens.
(slave values: iris of the lens + mirror shutter angle)
• max. Iris
In this mode the change in the exposure is compensated for
by the iris of the lens. If the adjustment range of the iris is
not sufficient for the given end values, the remaining rest
will be compensated for by the mirror shutter angle. In this
case, the shutter angle proportion is evenly distributed over
the entire compensation range.
(slave values: iris of the lens + possibly mirror shutter angle)
Functions
3.2.2.2 Overview of the settings available
with the COMPENSATION rotary switch
• max. )
In this mode the change in the exposure is compensated for
by the mirror shutter angle. If the adjustment range of the
shutter angle is insufficient for the given end value, the
remaining rest will be compensated for by the iris of the lens.
In this case, the aperture proportion is evenly distributed
over the entire compensation range.
(slave value: mirror shutter angle + possibly the iris of the lens)
• user
With this function ramps can be created which do not
result in constant exposure.
The iris of the lens, the shutter angle and the camera
speed can be combined as required.
15
Setup
CLM-2
535, 535B, 435, 16 SR3
RS
RF
CAL
BAT RDY
RUN
UC-C1
LENS CONTROL SYSTEM
WMU-1 + WRC-1
16
UMC-1 + URM-1
UC-R1
CCU
Setup
4. Setup
4.1 WRC-1 in wireless mode
In order to be able to use the WRC-1 in wireless mode, it
must be mounted on a Wireless Main Unit (WMU-1). The
Wireless Main Unit supplies the WRC-1 with power and
establishes the radio link with the camera.
Please contact your nearest ARRI dealer or one of the
service stations to update the EPROMs or to acquire the
latest software version.
Required system components:
An Universal Motor Controller (UMC-1) with an Universal
Radio Module (URM-1) must be mounted on the camera.
The UMC-1 and the URM-1 establish the radio link
outgoing from the camera. A Lens Control Motor CLM-2
for controlling the iris can be connected to the Universal
Motor Controller UMC-1.
For details about setting up the LCS components, refer
also to the LCS instruction manual.
Note:
In order to operate the WRC-1 the following
EPROM versions must be used:
WMU-1:
01.50 or higher
UMC-1:
01.50 or higher
ARRIFLEX 435
2.4 or higher
WRC-1 .................................................... K2.52087.0
WMU-1 ................................................... K2.52052.0
with WBU-2 battery .................................. K2.52088.0
WAC-1 charger ........................................ K2.52072.0
UMC-1 .................................................... K2.52040.0
with UC-C1 cable [K2.52046.0 as replacement]
dovetail adapter ....................................... K2.52080.0
URM-1 ..................................................... K2.52048.0
UC-R1 cable ............................................. K2.52079.0
for iris control additionally
CLM-2 ..................................................... K2.52036.0
possibly with console ................................. K2.52035.0
Note:
CLM-1 motors cannot be used
as iris motors for the WRC-1!
17
Setup
4.1.1 Mounting the WRC-1 on the
Wireless Main Unit (WMU-1)
• Switch off the Wireless Main Unit WMU-1 by pressing
the ON/OFF button ➪ photo.
RELEASE button
radio channel
ON button
RF-LED
• If an operating unit is already attached, remove it by
pressing the RELEASE button ➪ photo.
Swing out the unit and then remove it by pulling it
upwards.
CAL-LED
CAL button
• With the wide black pin ➪ photo pointing forward,
insert the WRC-1 into the free space on the Wireless
Main Unit WMU-1. Then press the WRC-1 onto the
WMU-1 until the module audibly snaps into position.
READY-LED
BAT-LED
Note:
The WRC-1 cannot be mounted on a WMU-1
together with other modules.
Note:
Do not separate the hand control units from one
another when they are switched on, as this can
result in randomly set lens limits.
RUN-LED
RUN button
18
Setup
4.1.2 Attaching the UMC-1 and URM-1
to the camera
For wireless operation the UMC-1 must be equipped
with an URM-1.
• Screw the antenna ➪ photo into the threaded
bushing on the URM-1.
antenna
• Unscrew the two allen screws ➪ photo from the
cover of the UMC-1 and then remove the cover.
allen screw
pin
allen screw
19
Setup
• Place the URM-1 onto the UMC-1, align both plugs
➪ photo with each other and do not tilt them while
attaching.
• Screw the URM-1 tight to the UMC-1 with the two
allen screws.
• Attach the Universal Motor Controller UMC-1 with the
URM-1 to the camera using the dovetail adapter
➪ photo with a 3/8" threaded bolt (K2.52080.0).
plug
• Connect the RS socket on the camera with the RS
socket on the UMC-1 using the UC-C1 cable.
dovetail adapter
20
Setup
• Connect the CCU socket on the camera with the CCU
socket on the UMC-1 using the UC-R1 cable.
ON/OFF switch
• Select the same radio channel on the UMC-1 as is set
on the WMU-1 ➪ photo (see LCS Instruction Manual,
chapter 5.1.2.1). If several lenses are to be remotely
controlled independently of each other, the radio
channels 0 and 5, 1 and 6, and 3 and 7 can not be
used simultaneously.
radio channel
IRIS socket
Due to local telecommunications regulations for
the 2.4 GHz band only certain channels are
available sometimes. Only allowed radio
channels must be used.
radio channel
Switch setting
0
2
3
4
5
6
7
Countries
USA, Canada, Mexico, New Zealand, Europe
except France and Spain
USA, Canada, Mexico, New Zealand, Europe
except France and Spain
Europe except Spain
USA, Canada, Mexico, New Zealand, France
Japan
Australia
Australia
Spain
8,9
see switch setting 0
1
ON/OFF switch
• Switch on the UMC-1 using the ON/OFF switch ➪ photo.
21
Setup
Setup with Iris control
locking lever
tube
A CLM-2 motor must be mounted if the iris of the lens is
to be controlled by the WRC-1.
Mounting the CLM-2 motor with/without console
receptacle
Console order number: K2.52035.0
ballcatch
• Flip up the locking lever ➪ photo and screw back
the ballcatch ➪ photo with a screwdriver until it
disappears completely in the bracket.
• Push the tube ➪ photo flush into the console receptacle, taking care that the slit in the tube points towards the ballcatch.
• Screw the ballcatch out of the bracket until the tube
can no longer be pushed out of the bracket.
• Turn the locking lever until a slight resistance can be
felt, then press the lever downwards.
• Fasten the motor unit CLM-2 to the console tube.
22
Setup
• Fasten the console to the support rods so that the
motor unit’s drive gear engages with the gear of the
lens ring. Ensure as little play as possible!
The motor unit CLM-2 can also be mounted directly onto
the support rods without the console.
• Connect the CLM-2 motor to the iris socket of the UMC-1.
Note:
All iris-related functions of the WRC-1 are not
available if the CLM-2 motor is not connected.
The WRC-1 then displays the ‘NO IRIS’ warning.
assembly with console
23
Setup
4.2 WRC-1 in cable mode
Connected with a cable to the camera only those fuctions of
the WRC-1 are available which relate to the camera speed
and the shutter angle. The iris of the lens cannot be controlled
in the cable mode because the iris motor cannot be accessed.
4.2.1 Mounting the WRC-1 on the
Wireless Handgrip Attachment
(WHA-1)
• If a control unit is already attached remove it by
pressing the release button. Swing out the unit and
then remove it by pulling it upwards.
Required system components:
WRC-1 .................................................... K2.52087.0
WC-W1-S cable ....................................... K2.52089.0
WHA-1 .................................................... K2.52070.0
WRC-1
• Insert the WRC-1 into the available free space on the
WHA-1 (Wireless Handgrip Attachment) with the
wide black pin pointing forward ➪ photo. Then
press the WRC-1 onto the WHA-1 until the module
audibly snaps into position.
RELEASE button
• Connect the WHA-1 to the CCU socket of the camera
using the WC-W1-S cable.
black pin
WHA-1
WC-W1
24
5.1 Operating modes
5.1.1 CAM mode
Note:
The operating elements of the WRC-1 control the same
functions as the corresponding elements on the camera:
MODE, SEL, SET, and the RUN LED. In CAM mode, the
OPEN button corresponds to the PHASE button on the camera.
The RAMP button corresponds to the PROG button on the
camera. The handwheel and the WRC- and COMPENSATION
rotary switches are without function in this operating mode.
• All functions are comprehensively described in the
camera instruction manuals and are not repeated.
The display of the WRC-1 shows the same information as
the camera display in this operating mode.
If the WRC-1 is only to be used in this operating
mode, it is advisable to set the WRC/CAM
sliding switch to CAM before the WRC-1 is
switched on. This ensures that the set frame rate
or a programmed shutter angle in the camera’s
PS/CCU mode and the WRC-1 in WRC mode
is not unintentionally altered.
In WRC mode the WRC-1 overwrites the
camera’s shutter angle and speed settings
(see Important instructions).
Camera programs which have been stored in
the camera via the CCU or the LCC are not
affected.
Operation
5. Operation
Forward or reverse run is set in the same way as on the
camera itself.
Note:
With the ARRIFLEX 535 forward or reverse run is
set in the same way as on the ARRIFLEX 535B,
435, 16SR 3/Advanced.
25
Operation
5.1.2 WRC mode
In this mode the WRC-1 offers convenient and quick access
to camera functions and additional programming options.
• Set the sliding switch on the camera from NORM to
PS/CCU ➪ photo.
The display of the WRC-1 flashes with the warning
‘not PSCCU’ until the camera’s sliding switch is set to
PS/CCU.
sliding switch NORM / PS/CCU
• Set the WRC/CAM sliding switch to WRC ➪ photo.
IRIS sliding switch
WRC/CAM sliding switch
READY-LED
OPEN/PHASEbutton
26
• The IRIS sliding switch governs whether the WRC-1
activates its control over the iris motor (IRIS ‘ON’), or
whether a connected iris motor is controlled by
another unit (IRIS ‘OFF’). This must be set before
switching on the WRC-1.
If the iris control is not activated (IRIS sliding switch
‘OFF’), the OPEN button serves as the PHASE button on
the camera ➪ photo.
Forward or reverse run is set in CAM mode and in the
same way as on the camera itself.
The WRC-1 does not have its own ON/OFF switch. In
wireless mode it is switched on by pressing the ON button
on the Wireless Main Unit (WMU-1) ➪ photo. In cable
mode it is supplied with power via the cable from the
camera as soon as this is switched on. When in use, the
background of the LCD of the WRC-1 is illuminated as
long as it is active.
READY-LED
ON/OFF
button
RF-LED
Operation
5.2 Switching on
The READY LED of the WRC-1 ➪ photo changes from
flashing red to a steady green once the communication
has been established with the camera. The WRC-1 is now
ready for use. In wireless mode the quality of the radio
connection must be read from the RF LED of the Wireless
Main Unit (WMU-1) ➪ photo.
Note:
The ZMU must always be switched on first if
cable and wireless units are used together.
The WRC-1 and ICU-1 may not be operated
simultaneously.
27
Important Instructions
28
5.3 Important instructions
• The WRC-1 controls
- the camera speed,
- the mirror shutter angle, and
- the iris of the lens.
All three parameters directly influence the exposure of
the film. In order to avoid unwanted results, and to
prevent the likelihood of incorrect use, all those
parameters controlled by the WRC-1 must be set and
controlled by the user. This also applies when one of
these parameters is not required for the currently
selected remote control: only when all three parameters
have been set (speed, mirror shutter angle and the
aperture) the film exposure is fully defined.
These values are defined separately for each mode,
i.e. the parameters can and must be individually set
for each mode.
Example: first of all a speed ramp is programmed and
shot. Then only the shutter angle is remotely controlled
for a transition from an outdoor take to an indoor
take. It would not be desirable to continue using those
settings that had been active at the end of the speed
ramp for the next take. Instead, the values set by the
user for the respective modes are active after switching
over to the other mode.
• When operating in WRC mode, the speed or mirror
shutter angle should not be set on the camera itself, as
these are repeatedly written over by the WRC-1. The
WRC-1 is an active unit and its settings have priority
over those of the camera. The camera retains the last
settings sent by the WRC-1 in its memory. This applies
when switching from WRC mode back to CAM mode,
as well as when disconnecting the WRC-1 from the
camera.
• All programmed end-stops and parameters set on the
WRC-1 are stored for as long as required, even when
the unit has been switched off. It is therefore possible
that end-stops for the handwheel had been programmed, which are not available when using this
WRC-1 with another camera model (e.g. high-speed
settings). The WRC-1 recognizes the connected
camera model, but does not independently change the
stored values. If these stored values should lie outside
of the range available for the connected camera
model, a warning is displayed.
• The WRC-1 and ICU-1 may not be operated simultaneously.
• All programs set using the WRC-1 are only stored in
the WRC-1 itself, and not in the camera. The RAMP
function of the WRC-1 therefore is not identical with
the camera’s own program function. It is therfore also
independent of a program which has been stored in
the camera using the CCU or the LCC. These camera
programs cannot be altered using the WRC-1. They
can only be activated and started in CAM mode like
using the operating buttons close to the camera display.
• If a warning is displayed that the compensation limit
values cannot be adhered to (readings ‘ANGLE
RANGE’, ‘IRIS RANGE’, ‘SPEED RANGE’), while
switching over the WRC or the COMPENSATION
rotary switches, the end-stops or limit values are still
programmed as described. The exceeded values can
then be corrected in the relevant submenus.
• The ZMU must always be switched on first if cable and
wireless units are used together.
The WRC-1 continuously sends values to the
camera when adjustments are carried out using
the handwheel or during ramp functions. The
radio connection must therefore function perfectly,
otherwise the correct exposure is not ensured.
The user must check that the RF LED is always
on green while the ramp function is running!
Important Instructions
In WRC mode the WRC-1 overwrites the
camera-internal settings for the camera speed
and the mirror shutter angle.
This can result in the following takes being incorrectly exposed if the set values are not checked.
In practice this means, for instance, that the
angle of the mirror shutter set by the WRC-1 is
retained; this also applies when switching back
from PS/CCU to NORM.
The shutter angle is not automatically reset to 180°!
• All warnings, such as when end-stops or limit values
are exceeded, are only shown in the main menu. The
submenus, on the other hand, are only used to define
all relevant values.
29
Important Instructions
30
• If exposure compensation is not possible with the set
options – e.g. adjusting the iris cannot be compensated
for at the same time by the iris – the WRC-1 displays
the message ‘NO FUNC’ (no function) in the main menu.
The camera can still be run for test purposes
even if the READY LED on the WRC-1 lights up
red or flashes. In this case, however, the
exposure may not comply with the values set in
the in the WRC-1.
• In order to avoid inconstant exposure, all adjustment
processes and ramps under 6 fps are started in the
camera’s dark phase. At these speeds, brief delays of
up to 0.7 seconds at 1 fps may occur until the adjustment or the ramp is started.
• A non-linar phase is integrated into those adjustment
processes and ramps which run at speeds of under
4 fps to avoid inconstant exposures. As a result the
adjusted parameters do not move continuously.
• In order to operate the WRC-1 the following EPROM
versions must be used:
WMU-1: ........................................ 01.50 or higher
UMC-1: .......................................... 01.50 or higher
ARRIFLEX 435 .................................... 2.4 or higher
Please contact your nearest ARRI dealer or one of the
service stations to update the EPROMs or to acquire
the latest software version.
• As the end-stops of the iris ring on the ARRIMACROS
are changed with the focusing action, the ARRIMACROS
may not be used with the LCS or the WRC-1 system.
5.4.1 Main menu
The main menu is indicated by a black bar in the top
right corner of the display ➪ photo. The currently
adjusted value and the value of one of the two possible
exposure compensations are shown in the display.
ON
READY
OFF
IRIS
WRC CAM
RUN
black bar
PROG symbol
PROG
OPEN
MODE
SEL/
SET/
RAMP
PHASE
Note:
ramp Iris
ramp
WRC
If PROG is also displayed ➪ photo, a time-controlled
ramp function (ramp Iris, ramp ) , ramp fps) has been
selected using the WRC rotary switch. In this mode the
handwheel is without function in the main menu, as the
ramp is started with the RAMP button. In the three other
WRC rotary switch positions (fps, ) , Iris) a parameter
can be adjusted directly using the handwheel. The display
shows the respective value and an automatically generated
compensation value.
ramp fps
fps
Iris
off
Iris
Iris
50%
max Iris
max
WRC-1
fps,
,Iris
com
sat
ion
pen
user
Using the menus
5.4 Using the menus
handwheel
All warnings, such as when end-stops or limit
values are exceeded, are only shown in the
main menu. The submenus are only used to
define all relevant values.
31
ON
READY
WRC CAM
OFF
IRIS
MODE button
SET button
OPEN
MODE
SEL/
SET/
RAMP
PHASE
WRC
ramp Iris
ramp
Iris
Iris
ramp fps
fps
Iris
50%
max Iris
max
WRC-1
fps,
,Iris
If exposure compensation is not possible with
the set options – e.g. adjusting the iris cannot
be compensated at the same time by the iris –
the WRC-1 displays the message ‘NO FUNC’
(no function) in the main menu.
RUN
off
en
comp
sation
Using the menus
Note:
user
In the main menu limit values, end-stops for the handwheel
(definition: see Glossary or 5.4.2.1 Limit values), or fixed
values (definition: see Glossary or 5.4.2.2 Fixed values
below) for the exposure cannot be pre-set. The main
menu valid for each operating mode is explained later on
with the respective mode.
• By pressing the SET button values that are currently not
displayed can be checked, e.g. the current shutter angle
and the camera speed can be checked in the iris main
menu.
• Press the MODE button to change from the main menu
to the submenus. Press the MODE button again to enter
the next submenu until the main menu mode reappears.
The submenu sequence can vary according to the operating modes selected using the WRC- and COMPENSATION
rotary switches.
32
The submenus are used to define the end-stops of the
handwheel and all relevant limit and fixed values.
The value in the first line of the display corresponds to the
left handwheel end-stop or the start value of the ramp.
The value in the second line of the display corresponds to
the right handwheel end-stop or the end value of the ramp.
5.4.2.1 Limit values
5.4.2.2 Fixed values
A so-called limit value is either the left or the right end-stop
of the handwheel, or the start and end value of a timecontrolled ramp.
The limit values for the master value are always defined in
the first submenu.
The remaining parameters for the film exposure are defined
in the following submenus. Example: If the camera speed
has been selected as the parameter to be adjusted, the
shutter angle and the aperture of the lens must be defined
in the next submenus, if they are controlled by the WRC-1.
If a ramp function has been selected, the duration of the
ramp must also be entered.
• Defining the handwheel’s end-stops:
If a function has been selected using the WRC rotary
switch which provides remote control with the handwheel
(Iris, ) , fps), the two values for the left and the right
handwheel end-stop are defined in the first submenu.
• Defining the start and end values of a ramp:
If a function has been selected using the WRC rotary
switch which controls a program over a pre-defined
period of time (ramp Iris, ramp ) , ramp fps), the start
and end values of the ramp are defined in the first
submenu; e.g. the start and the end speed in the case
of a speed ramp.
Note:
Multiple limit values are defined if changes in
exposure are automatically compensated for –
example: Iris compensated with the shutter angle;
the aperture of the lens alters during the adjustment (master value) and the shutter angle is
adjusted automatically as a compensation. One
of the two limit values for the shutter angle can be
assigned; the other limit value is automatically
calculated by the WRC-1. It must be ensured
that the available adjustment range is not
exceeded.
Using the menus
5.4.2 Submenus
33
ON
READY
WRC CAM
OFF
IRIS
SEL button
SET button
OPEN
MODE
SEL/
SET/
ramp Iris
ramp
ramp fps
fps
Iris
50%
max Iris
max
• By pressing the SEL button the adjusted value is stored
and the next digits are activated. After the last digit
has been entered the edit mode is exited.
off
Iris
Iris
• The flashing digits can be edited using the handwheel.
RAMP
PHASE
com
sat
ion
pen
user
If only plain figures are to be adjusted, the decimal positions
can easily be set to ‘0’ by pressing the SET button. The
values for the next line can then be entered.
WRC-1
fps,
,Iris
34
• In a submenu press the SEL button for longer than 2
seconds to activate the edit mode, in which values can
be defined.
RUN
PROG
WRC
Using the menus
• Press the MODE button to change from the main menu
to a submenu. Each further press of the MODE button
takes the user to the next submenu, until the main
menu mode reappears.
handwheel
The submenus cannot be edited while the camera is running.
35
Using the menus
Controlling the Iris
Iris
Iris
Iris
ramp Iris
ramp Iris
ramp Iris
comp. off
comp. <)
comp. user
comp. off
comp. <)
comp. user
PROG
PROG
fps
fps
PROG
fps
PROG
PROG
PROG
PROG
PROG
PROG
fps
PROG
fps
fps
PROG
fps
PROG
fps
PROG
PROG
PROG
PROG
36
If the aperture of the lens (iris) is to be controlled by the
WRC-1, a lens motor CLM-2 must be mounted on the
camera and connected to the UMC-1/URM-1.
Note:
The iris can only be adjusted using CLM-2 motors.
If a CLM-1 motor is used the warning ‘NO IRIS’
is displayed.
When switching on the WRC-1, the IRIS sliding switch ➪
photo is used to determine whether the WRC-1 (‘IRIS ON’)
or another unit (e.g. a WFU-1) (‘IRIS OFF’) controls the
connected iris motor.
IRIS sliding switch
ON
• The IRIS sliding switch must be set to ‘ON’ before
turning on the WRC-1.
READY
OFF
IRIS
WRC CAM
Controlling the Iris
5.5 Controlling the iris
(master value: Iris)
RUN
PROG
OPEN
MODE
SEL/
SET/
RAMP
PHASE
ramp Iris
ramp
WRC
If the IRIS sliding switch is not set to ‘ON’ and an operating
mode is selected, which requires an iris motor, the warning
‘NO IRIS’ is displayed. This warning is also displayed if the
IRIS sliding switch is set to ‘ON’ although a CLM-2 motor
has not yet been connected. In this case the CLM-2 motor
must be connected to the IRIS socket on the UMC-1.
ramp fps
fps
off
Iris
Iris
50%
max Iris
com
sat
ion
pen
37
Controlling the Iris
38
First the end-stops of the lens must be calibrated and the
engraved T-stops must be assigned in the WRC-1 (as
described below) for each lens being used.
As the end-stops of the iris ring on the
ARRIMACROS change when the lens is focussed,
the ARRIMACROS may not be used with the
LCS or the WRC-1 system.
Before assigning the T-stop values and calibrating
the end-stops of the iris ring of the lens, check
all the motors you want to use to be firmly
attached to the support rods of the bridge plate.
5.5.1 Assigning the T-stops
The adjustable T-stops (1, 1.4, 2, 2.8, 4, 5.6, etc.) must be
correctly assigned in the WRC-1 to the various positions
engraved on the iris ring of the lens. The iris cannot be
remotely controlled until the respective positions have been
assigned. This assignment is stored in the WRC-1 in a
table (tbl).
• If a lens has not yet been selected and the T-stops have
not yet been assigned (condition on delivery from the
factory, or the active iris table has been deleted from
the memory), a flashing warning appears – ‘IRIS TBL’
– when the WRC-1 is switched on with the IRIS sliding
switch set to the position ‘ON’. Press the MODE button
once to enter the input mode.
• If a lens has already been selected and T-stops have
been assigned previously, the menu for programming
the T-stops of the iris is always the last submenu before
returning to the main menu in the WRC rotary switch
position ‘IRIS’.
Press the MODE button three times in the WRC rotary
switch position ‘IRIS’ and the COMPENSATION rotary
switch at ‘OFF’ until ‘TBL LOAD’ appears on the display.
Depending on the selected function and compensation, this input menu can also be found in
other relevant positions by repeatedly pressing
the MODE button.
In the table submenu, it is possible to:
• load factory- and user-defined iris tables,
menu option ‘TBL LOAD’,
• delete iris tables from the active memory
(factory- or user-defined iris tables
are not deleted),
menu option ‘TBL DEL’,
• edit iris tables,
menu option ‘TBL EDIT’, or
• store user-defined iris tables on one of the 10 available
memory areas.
menu option ‘TBL STORE’.
The values of the last lens used may still be
active and stored in the WRC-1.
All settings and the active iris table should
therefore always be checked in order to avoid
incorrect exposures!
Controlling the Iris
Note:
• The required function is selected using the handwheel
and then activated by pressing the SEL button.
For the Zeiss Ultra Primes, the Variable Primes, the Highspeed set, and the Standard set iris tables are already
programmed in the WRC-1. For other lenses iris tables
can be stored.
10 memory areas are available.
39
Controlling the Iris
5.5.1.1 Loading iris tables for Zeiss Ultra Primes,
Variable Primes, High-speed, Standard or
user-defined lenses
(‘TBL LOAD’)
The iris tables for the factory pre-defined lenses
require that a standard gear ring is used on the
lens motor (50 teeth). If other gear rings are used,
the T-stop scale must be completely programmed
from scratch. This also applies if a gear adapter
ring is used with the lens.
The pre-defined iris tables are loaded as follows:
• If ‘IRIS TBL’ flashes on the display when the WRC-1 is
switched on, the MODE button must be pressed once
to enter the ‘TBL LOAD’ mode.
If a lens has already been selected and the T-stops
have been assigned previously, the menu for selecting
the lens can be entered in the WRC rotary switch
position ‘IRIS’ and the COMPENSATION rotary switch
set to ‘OFF’ by pressing the MODE button three times.
• Then press the SEL button. The lens type is shown in
the first line of the display.
40
Controlling the Iris
Pre-defined lens types are:
Display:
UP
VAr P
HS 35
Std35
HS 16
User
Lens set:
ARRI Zeiss Ultra Primes
ARRI Zeiss Variable Primes
ARRI Zeiss High-speed lenses for 35mm film
ARRI Zeiss Standard lenses for 35mm film
ARRI Zeiss High-speed lenses for 16mm film
lens previously defined by the user
• Select the required lens set using the handwheel.
Then press the SEL button. The focal length then
appears in the second line of the display.
CAL button
• Select the focal length using the handwheel.
Confirm the selection by pressing the SEL button.
• The display now shows the command ‘DO CAL’.
Start the calibration by pressing the CAL button on the
WMU-1 ➪ photo.
41
Controlling the Iris
• ‘ADJ’ now flashes in the first line of the display.
A T-stop value is shown in the second line.
• Adjust the iris ring to the displayed value using the
handwheel.
• The T-stop is assigned by pressing the SET button.
This is indicated in the first line with an ‘I’ next to ‘TBL’.
This defines the entire iris table.
‘DONE’ is shown on the display for one second.
• The display then shows ‘TBL’ in the first line,
and the letter ‘F’ and a T-stop value in the second line.
The individual T-stops available for this lens must now
be checked using the handwheel!
An ‘I’ is shown in the first line of the display next to
‘TBL’ for every T-stop programmed for this lens.
Note:
Only full T-stops are accessible for checking to
speed up the process in this mode.
After loading the iris table, all individual T-stops
on the lens must be checked by adjusting with
the handwheel in order to avoid incorrect
exposures!
42
• To go back to the main menu press of the MODE button
again.
Controlling the Iris
• Press the MODE button to go back to the table menu
(TBL LOAD, TBL DEL, TBL EDIT, TBL STORE).
43
Controlling the Iris
5.5.1.2 Programming an iris table
for other lenses
(‘TBL EDIT’)
• If ‘IRIS TBL’ flashes on the display when the WRC-1 is
switched on, the MODE button must be pressed once
to enter the ‘TBL LOAD’ mode.
If a lens has already been selected and the T-stops
have been assigned previously, the menu for selecting
the lens can be entered in the WRC rotary switch
position ‘IRIS’ and the COMPENSATION rotary switch
set to ‘OFF’ by pressing the MODE button three times.
The values for the last lens used may still be stored
and active in the WRC-1. All settings and the
active iris table should therefore always be
checked in order to avoid incorrect exposures!
• To delete an old assignement (iris table), turn the
handwheel until ‘DEL’ is shown in the second line of
the display. Then press the SEL button. ‘TBL’ flashes in
the first line. Press the SET button to finally delete the
old assignement. ‘DONE’ is shown on the display for
one second.
44
• Turn the handwheel until ‘TBL EDIT’ is displayed.
Press the SEL button to go to the input mode.
• Turn the handwheel to the left until the first T-stop of
the iris ring of the lens being used is shown in the
second line of the display.
This must be a full T-stop from the standard T-stop
range.
• Then press the SEL button. ‘ADJ’ now flashes in the
first line of the display.
• Adjust the iris ring of the lens to the displayed value
using the handwheel.
Controlling the Iris
• Press the CAL button on the WMU-1 to start the
calibration process before entering any values.
• The T-stop is assigned by pressing the SET button. This
is indicated in the first line with an ‘I’ next to ‘TBL’.
• In case you need to delete this assignment, press the
SET button again. The ‘I’ next to ‘TBL’ disappears again.
• Turn the handwheel until the next T-stop on the iris ring
of the lens being used is shown on the display. Assign
this and the next T-stops as described above.
45
Controlling the Iris
46
Note:
If the T-stop scale of the lens being used is linear,
it is sufficient to enter just two T-stops, which must
be at least four T-stops apart, in order to define
the iris table. If the T-stop scale is not linear, all
the T-stops must be assigned individually.
After programming the iris table, all individual
T-stops on the lens must be checked by adjusting
with the handwheel in order to avoid incorrect
exposures!
Note:
If the lens has a CLOSE position, this must also
be defined, as the iris table only applies up to
the last value before the CLOSE position! When
assigning, the CLOSE position is programmed
after the highest possible T-stop setting.
Note:
For compensating the exposure, only the range
between full T-stops may be used! Example: the
iris scale of the lens reaches from T2.2 to 22.
The values for T4 and T16 are assigned. The
resulting usable range reaches from T2.8 to
T22, as T2.2 is not a T-stop from the standard
T-stop range (T2.0).
Note:
If a T-stop value has been assigned which
cannot be correct, a warning is displayed; e.g.
T-stop 11 cannot lie between 5.6 and 8. The
incorrectly positioned value must be deleted.
If the iris table should remain available after using
another lens, it must be stored as described below. This
also applies when an iris table has been re-edited.
After assigning the T-stops the resulting iris table can be
stored for later use.
• Press the MODE button in the submenu for assigning
the T-stops to go back to the table menu (TBL LOAD,
TBL DEL, TBL EDIT, TBL STORE).
• Turn the handwheel until ‘STORE’ is shown in the
second line.
• Press the SEL button. ‘STORE’ is displayed in the first
line, and the number of the memory area is shown in
the second line.
• Select the number of the required memory area using
the handwheel. 10 memory areas are available.
When storing, existing table data in this
memory area are overwritten without warning!
• The iris table is stored by pressing the SEL button.
‘DONE’ is displayed for one second.
Controlling the Iris
5.5.1.3 Storing an iris table
(‘TBL STORE’)
• Note down the number of the memory area together
with the programmed lens to simplify activating lenses
at a later time.
47
Controlling the Iris
5.5.1.4 Loading a user-defined iris table
(‘TBL LOAD’)
• If ‘IRIS TBL’ flashes on the display when the WRC-1 is
switched on, the MODE button must be pressed once to
enter the ‘TBL LOAD’ mode.
If a lens has already been selected and the T-stops have
been assigned previously, the menu for selecting the
lens can be entered in the WRC rotary switch position
‘IRIS’ and the COMPENSATION rotary switch set to
‘OFF’ by pressing the MODE button three times.
• Turn the handwheel until ‘LOAD’ is displayed in the
second line; confirm the selection by pressing the SEL
button.
• Select ‘USER’ with the handwheel. Then press the SEL
button. The required memory area can be selected in
the second line using the handwheel (see Chapter
5.5.1.2 Storing an iris table, directly preceding this
chapter).
• Confirm the selection by pressing the SEL button.
• The display now shows the command ‘DO CAL’.
Start the calibration process by pressing the CAL
button on the WMU-1.
48
Controlling the Iris
The WRC-1 is not able to check whether the
selected user-defined iris table is actually
compatible with the lens being used. An error
message can only be displayed if the iris motor
reaches the end-stops of the lens during calibration, and these had been positioned elsewhere while the lens was being programmed.
CAL button
• If the wrong iris table has been unintentionally selected
(e.g. by choosing the wrong memory area), and the
iris motor strikes unexpected end-stops during the
calibration process, the warning ‘LENS ERROR’ is
displayed. Press the SEL or SET button to go to the
mode for assigning the T-stops. The current T-stops can
be reassigned.
ft
m
h:min
TC UB
fpsR
sec:f
1
5
2
6
3
7
4
8
filter
jam
PROG asy
end
bat
49
Controlling the Iris
• If the lens has been successfully calibrated, ‘ADJ’
flashes in the first line of the display.
A T-stop value is shown in the second line.
• Adjust the iris ring of the lens to the displayed value
using the handwheel.
• The T-stop is assigned by pressing the SET button.
This is indicated in the first line with an ‘I’ next to ‘TBL’.
This defines the entire iris table. ‘DONE’ is displayed
for one second.
• The display then shows ‘TBL’ in the first line,
and the letter ‘F’ and a T-stop value in the second line.
All individual T-stops must be checked by adjusting
with the handwheel! An ‘I’ is shown in the first line of
the display next to ‘TBL’ for every T-stop assigned for
this lens.
After loading the iris table, all individual T-stops
on the lens must be checked by adjusting with
the handwheel in order to avoid incorrect
exposures!
• Press the MODE button to go back to the table menu
(TBL LOAD, TBL DEL, TBL EDIT, TBL STORE). To go back
to the main menu press of the MODE button again.
50
If a previously programmed iris table is re-edited,
the corresponding table must first be loaded
from its memory area as described above.
The handwheel must then be turned in the table
menu (TBL LOAD, TBL DEL, TBL EDIT, TBL STORE)
until ‘EDIT’ is displayed in the second line.
Confirm with the SEL button to return to the edit
mode for this table.
5.5.1.5 Important instructions for programming
the iris of the lens
• If the lens has a CLOSE position, this must also be defined,
as the iris table only applies up to the last value before
the CLOSE position! When assigning, the CLOSE position
is programmed after the highest possible T-stop setting.
• If the T-stop scale of the lens being used is linear, it is
sufficient to enter just two T-stops, which must be at
least four T-stops apart, in order to define the iris
table. If the T-stop scale is not linear, all the T-stops
must be assigned individually.
from T2.8 to T22, as T2.2 is not a T-stop from the
standard T-stop range (this would be T2.0, for example).
• The display shows full T-stops followed by the tenth of
a T-stop. Example: T-stop 2.8 plus half a T-stop is
shown as 2.8_5. The tenths of a T-stop are linearly
divided between the two full T-stop positions.
• To check the image in the viewfinder, the iris can be
opened completely by pressing the OPEN button. The
iris remains open until the OPEN button is released
again. This does not alter the programmed settings.
The OPEN button is without function while the camera
is running.
Controlling the Iris
Note:
• For compensating the exposure, only the range between
full T-stops may be used! Example: the iris scale of the
lens reaches from T2.2 to 22. The values for T4 and
T16 are assigned. The resulting usable range rechaes
51
Controlling the Iris
52
Iris
5.5.2 Iris / compensation off
comp. off
The iris can be manually adjusted within the pre-defined
end-stops of the handwheel.
Differences in exposure are not automatically
compensated for.
The main menu shows ‘IRIS’ in the first display line, and
the currently adjusted T-stop in the second line.
fps
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button. The iris remains open until the
OPEN button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
By pressing the SET button the currently set shutter angle
(if controlled by the WRC-1) can be shown in the first
display line. The currently set camera speed is shown in
the second display line.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The left and right end-stop for the handwheel (minimum and maximum aperture) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds. The T-stop
value in the first display line flashes. The required value
can now be adjusted using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
Controlling the Iris
selected speed cannot be attained with this
camera). Correct parameters must be set before
the camera is started!
• Press the MODE button to go to the next submenu.
To define the fixed values for the mirror shutter angle
(if controlled by the WRC-1), and the camera speed,
use the SEL and SET buttons and the handwheel, as
described above.
53
Controlling the Iris
54
• Press the MODE button to enter the next submenu. The
table menu has already been described under 5.5.1.
Iris
comp. <)
• Press the MODE button to go back to the main menu.
fps
camera does not have an electronically adjustable
mirror shutter);
readings with ‘RANGE’ in the second display line
indicate that the adjustment range of a parameter
has been exceeded (example: the selected speed
cannot be attained with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The iris can be manually adjusted within the pre-defined
end-stops of the handwheel (master value: Iris).
The exposure is automatically compensated for with the
mirror shutter angle. The visible depth of field can be
altered with this function.
The first line of the main menu shows the shutter angle,
which is automatically calculated within the pre-defined
limits. The second line shows the currently adjusted T-stop
of the lens using the handwheel.
Note:
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (examples: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected. The connected
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button.
The iris remains open until the OPEN button is
released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
Controlling the Iris
5.5.3 Iris /
compensation shutter angle
By pressing the SET button the currently set camera speed
can be shown in the second display line.
55
Controlling the Iris
56
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The left and right end-stop of the handwheel
(minimum and maximum aperture) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The T-stop value in the first display line flashes.
The required value can now be adjusted using the
handwheel. Press the SEL button again to switch to the
next digit. The first digits are confirmed, and the decimal
is set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
If the compensation range available with the
shutter angle is exceeded, the warning ‘ANGLE
RANGE’ flashes on the display after returning
to the main menu. The settings for the iris or the
shutter angle must be corrected accordingly!
The camera can still be started for test purposes
in spite of the flashing warning. However, the
exposure may be incorrect!
• Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the first digits
flash in the first or second display line.
These can now be adjusted using the handwheel.
The automatically calculated other limit value is shown
in the other display line.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’, by pressing the SET button.
The minimum shutter angle corresponds to the selected
maximum aperture (smallest T-stop number).
• Press the MODE button to enter the next submenu. The
table menu has already been described under 5.5.1.
• Press the MODE button to go back to the main menu.
Controlling the Iris
• Press the MODE button to go to the next submenu.
The limit values for the shutter angle can be defined:
The shutter angle is automatically adjusted to compensate the exposure while the iris is adjusted with the
handwheel. One of the two limit values (minimum or
maximum shutter angle, depending on the adjustment
direction of the iris) can be defined; the other limit
value is automatically calculated by the WRC-1.
• Press the MODE button to go to the next submenu.
The fixed value for the camera speed is defined using
the SEL and SET buttons and the handwheel.
57
Controlling the Iris
Iris
5.5.4 Iris / compensation user
comp. user
fps
Using the handwheel, the iris can be manually adjusted
within the user-defined end-stops, simultaneously together
with the values for the shutter angle and the camera speed.
If appropriate values are selected, either the exposure can
be kept at a constant level, or an adjustment process can
be defined to change the exposure as required (e.g.
fading in or out).
Note:
fps
The function of the user mode always remains
the same, irrespective of the position of the WRC
rotary switch (Iris, ) or fps): The timing of the
simultaneous adjustment processes is controlled
using the handwheel. If a ramp function is
selected (ramp Iris, ramp ) or ramp fps), a
ramp duration can be defined. In this case the
handwheel is without function in the main menu.
Differences in exposure are not automatically
compensated for.
58
The main menu shows the symbol ’ ) ’ in the first display line
for adjusting the shutter angle (if controlled by the WRC-1)
and the currently adjusted T-stop (if controlled by the WRC-1).
By pressing the SET button the currently adjusted mirror
shutter angle can be shown in the first line of the display.
The current camera speed is displayed in the second line.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line indicate
that the selected function is currently not available
(example: ‘NO IRIS’ although the iris control is
activated on the WRC-1, the iris motor has not
yet been connected);
readings with ‘RANGE’ in the second display line
indicate that the adjustment range of a parameter
user mode
has been exceeded (example: the selected
speed cannot be attained with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
Controlling the Iris
In the user mode, all adjustments are not
carried out linearly within the adjustment time,
as in the other WRC modes. For this reason,
ramp durations may be different, compared to
those in the other WRC modes.
59
Controlling the Iris
60
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button. The iris remains open until the
OPEN button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
By pressing the SET button the currently adjusted shutter
angle (if controlled by the WRC-1) can be shown in the
first display line.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like incorrect exposure. The
exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The left and right end-stop for the handwheel (minimum and maximum aperture) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The T-stop value in the first display line flashes.
The required value can now be adjusted using the
handwheel. Press the SEL button again to switch to the
next digit. The first digits are confirmed, and the
decimal is set to ‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
shutter angle (if controlled by the WRC-1), use the SEL
and SET buttons and the handwheel, as described above.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• If the defined values result in a constant exposure, the
display shows ‘CONST LIGHT’ when the MODE button
is pressed. If this reading is not shown, the exposure is
altered while the handwheel is adjusted.
• Press the MODE button to go to the next submenu. The
table menu has already been described under 5.5.1.
• Press the MODE button to go back to the main menu.
Controlling the Iris
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
camera speed, use the SEL and SET buttons and the
handwheel. The first display line shows the value for the
left end-stop, the second line shows the value for the
right end-stop.
61
Controlling the Iris
ramp Iris
5.5.5 Ramp iris / compensation off
comp. off
PROG
The iris of the lens is continuously adjusted within the predefined limit values over a pre-defined period of time after
pressing the RAMP button (ramp, definition see Glossary).
Differences in exposure are not automatically
compensated for.
PROG
PROG
fps
The main menu shows ‘RA’ in the first line to indicate the
ramp function, and the currently adjusted T-stop of the
lens in the second line.
PROG
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
62
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button. The iris remains open until the
OPEN button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
By pressing the SET button the currently set shutter angle
(if controlled by the WRC-1) can be displayed in the first
display line, the currently set camera speed is shown in
the second display line.
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Iris
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
63
Controlling the Iris
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum aperture of the lens can be defined.
The first display line shows the start value of the aperture,
and the second line the value at the end of the ramp.
• Press the MODE button to go to the next submenu.
To define the fixed values for the mirror shutter angle
(if controlled by the WRC-1) and the camera speed,
use the SEL and SET buttons and the handwheel, as
described above.
• Press the SEL button for longer than 2 seconds.
The T-stop value in the first display line flashes.
The required value can now be adjusted using the
handwheel. Press the SEL button again to switch to the
next digit. The first digits are confirmed, and the decimal
is set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
64
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the MODE button to go back to the main menu.
Controlling the Iris
• Press the MODE button to go to the next submenu. The
table menu has already been described under 5.5.1.
65
Controlling the Iris
ramp Iris
comp. <)
PROG
PROG
PROG
PROG
fps
5.5.6 Ramp iris /
compensation shutter angle
The iris of the lens is continuously adjusted within the pre-set
limit values (master value: Iris) over a pre-defined period
of time after pressing the RAMP button (ramp, definition
see Glossary).
The mirror shutter angle is automatically adjusted by the
WRC-1 within the pre-defined limit values, to compensate
the exposure.
The visible depth of field can be altered with this function.
In the main menu the automatically calculated shutter angle
is shown in the first display line, and the current T-stop is
shown in the second line.
PROG
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
66
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button. The iris remains open until the
OPEN button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
By pressing the SET button the currently set camera speed
can be shown in the second display line.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
Controlling the Iris
Note
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
67
Controlling the Iris
68
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum aperture can be defined.
The first display line shows the start value of the aperture,
and the second line the value at the end of the ramp.
• Press the SEL button for longer than 2 seconds. The T-stop
value in the first display line flashes. The required value
can now be set using the handwheel. Press the SEL button
again to switch to the next digit. The first digits are
confirmed, and the decimal is set to ‘0’ by pressing
the SET button.
The values in the second display line can be set
accordingly.
If the compensation range available with the
shutter angle is exceeded, the warning ‘ANGLE
RANGE’ flashes on the display after returning
to the main menu. The settings for the iris or the
shutter angle must be corrected accordingly!
The camera can still be started for test purposes
in spite of the flashing warning. However, the
exposure may be incorrect!
• Press the MODE button to go to the next submenu.
The limit values for the shutter angle can be defined.
The shutter angle is automatically adjusted by the
WRC-1 to compensate the exposure, while the iris is
being adjusted. One of the two limit values (minimum
or maximum shutter angle, depending on the adjustment
direction of the iris) can be defined; the other limit value
is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the first digits
flash in the first or second display line. These can now
be set using the handwheel. The automatically calculated
other limit value is shown in the other display line.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is
automatically set to ‘0’, by pressing the SET button.
The minimum shutter angle corresponds to the selected
full aperture (smallest T-stop number).
• Press the MODE button to go to the next submenu.
To enter the the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the MODE button to go to the next submenu. The
table menu has already been described under 5.5.1.
• Press the MODE button to go back to the main menu.
Controlling the Iris
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
• Press the MODE button to go to the next submenu.
The fixed value for the camera speed is defined using
the SEL and SET buttons and the handwheel.
69
Controlling the Iris
ramp Iris
5.5.7 Ramp iris / compensation user
comp. user
PROG
fps
PROG
PROG
The iris of the lens is continuously adjusted, together with
the shutter angle (if controlled by the WRC-1) and the
camera speed, within the freely definable limits over a
pre-defined period of time after pressing the RAMP button
in the camera run.
If appropriate values are selected, either the exposure can
be kept at a constant level, or a ramp can be defined to
change the exposure as required (e.g. fading in or out).
Note:
PROG
fps
PROG
PROG
The function of the user mode always remains
the same, irrespective of the position of the
WRC rotary switch (Iris, ) or fps): The timing of
the simultaneous adjustment processes is
controlled using the handwheel.
If a ramp function is selected (ramp Iris, ramp )
or ramp fps), a ramp duration can be defined.
The ramp is started while the camera is running
by pressing the RAMP button. In this case the
handwheel is without function in the main menu.
PROG
Differences in exposure are not automatically
compensated for.
70
The main menu shows the symbol ’ ) ’ in the first line of the
display for adjusting the shutter angle (if controlled by the
WRC-1) and the currently adjusted T-stop. The currently adjusted mirror shutter angle (if controlled by the WRC-1) can
be shown in the first display line by pressing the SET button.
The currently adjusted camera speed is displayed in the
second line.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
user mode
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
Controlling the Iris
In the user mode, all adjustments are not
carried out linearly within the adjustment time,
as in the other WRC modes. For this reason,
ramp durations may be different, compared to
those in the other WRC modes.
71
Controlling the Iris
72
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Note:
To check the image in the viewfinder, the iris can be
opened completely by pressing the OPEN button.
The iris remains open until the OPEN button is
released again. This does not alter the programmed settings. The OPEN button is without
function while the camera is running.
• Press the SEL button for longer than 2 seconds.
The T-stop value in the first display line flashes. The
required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
shutter angle (if controlled by the WRC-1), use the SEL
and SET buttons and the handwheel, as described above.
The first display line shows the start value of the shutter
angle, and the second line the value at the end of the
ramp.
The first display line shows the start value of the camera
speed, and the second line the value at the end of the
ramp.
• If the defined values result in a constant exposure, the
display shows ‘CONST LIGHT’ when the MODE button
is pressed. If this reading is not shown, the exposure is
altered during the ramp.
Controlling the Iris
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum aperture can be defined.
The first display line shows the start value of the aperture,
and the second line the value at the end of the ramp.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
camera speed, use the SEL and SET buttons and the
handwheel.
73
Controlling the Iris
74
• Press the MODE button to go to the next submenu. To
enter the ramp duration, use the SEL and SET buttons
and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected.
The camera can still be started for test purposes
in spite of the flashing warning. However, the
exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
Note:
While the ramp duration is being set, the display
shows the automatically calculated screen time
in the first display line, which corresponds to
the selected projection speed (see the next two
bullet points).
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Iris
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
75
Controlling the Shutter Angle
76
<)
<)
<)
ramp <)
ramp <)
ramp <)
comp. off
comp. Iris
comp. User
comp. off
comp. Iris
comp. User
PROG
PROG
fps
fps
PROG
fps
PROG
PROG
PROG
PROG
PROG
PROG
fps
PROG
fps
fps
PROG
fps
PROG
fps
PROG
PROG
PROG
PROG
For cameras without an electronically adjustable mirror
shutter, the warning ‘NO ANGLE’ is displayed in the
main menu when selecting a function for the shutter angle.
The READY LED flashes green.
If the iris of the lens is not controlled by the WRC-1, the
warning ‘NO IRIS’ appears in the main menu when
selecting a WRC function or compensation which requires
the iris ring to be controlled.
Controlling the Shutter Angle
5.6 Controlling the mirror shutter angle
77
Controlling the Shutter Angle
78
<)
comp. off
5.6.1 Shutter angle /
compensation off
The mirror shutter angle can be manually adjusted within
the pre-defined end-stops of the handwheel.
Differences in exposure are not automatically
compensated for.
fps
The main menu shows the currently adjusted mirror shutter
angle in the first display line, and ‘ANGLE’ in the second line.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
By pressing the SET button, the currently set T-stop (if controlled by the WRC-1) can be displayed in the first display
line, and the currently set camera speed is shown in the
second display line.
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the left and right
end-stop of the handwheel (minimum and maximum
mirror shutter angle) can be defined.
The first display line shows the value for the left
handwheel end-stop, the second line shows the value
for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
To define the fixed values for the aperture of the lens
(if controlled by the WRC-1) and the camera speed,
use the SEL and SET buttons and the handwheel, as
described above.
The display shows full T-stops followed by the tenth of
a T-stop. Example: T-stop 2.8 plus half a T-stop is
shown as 2.8_5. The tenths of a T-stop are linearly
divided between the two full T-stop positions.
• Press the MODE button to go back to the main menu.
Controlling the Shutter Angle
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
79
Controlling the Shutter Angle
80
<)
comp. Iris
5.6.2 Shutter angle /
compensation iris
The mirror shutter angle can be manually adjusted within
the pre-defined end-stops of the handwheel
(master value: Shutter angle).
The exposure is automatically compensated for with the
iris of the lens. The visible depth of field can be altered
with this function.
fps
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The main menu shows in the first display line the currently
adjusted mirror shutter angle. The second display line
shows the currently adjusted T-stop of the lens, which is
automatically calculated within the pre-defined limit values.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
By pressing the SET button, the currently set camera speed
can be shown in the second display line.
• Press the MODE button in the main menu to enter the
first submenu. The values for the left and right end-stop
of the handwheel (minimum and maximum mirror
shutter angle) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the iris can be defined.
The iris is automatically adjusted to compensate the
exposure while the shutter angle is adjusted using the
handwheel. One of the two limit values (minimum or
maximum aperture, depending on the adjustment
direction of the shutter angle) can be defined; the other
limit value is automatically calculated by the WRC-1.
Controlling the Shutter Angle
Note
81
Controlling the Shutter Angle
82
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the T-stop value
flashes in the first or second display line.
This can now be set using the handwheel.
The automatically calculated other limit value is shown
in the other display line.
Press the SEL button again to switch to the decimal.
The selected T-stop is confirmed and the decimal set to
‘0’ by pressing the SET button.
The maximum aperture (smallest T-stop number)
corresponds to the selected minimum shutter angle
opening.
If the compensation range available for the iris
ring is exceeded (e.g. the start T-stop is at the
beginning or end of the adjustment range), the
READY LED flashes green and the warning ‘IRIS
RANGE’ flashes on the display after returning
to the main menu. The settings for the iris or the
shutter angle must be corrected accordingly!
The camera can still be started for test purposes
in spite of the flashing warning. However, the
exposure may be incorrect!
• Press the MODE button to go back to the main menu.
Controlling the Shutter Angle
• Press the MODE button to go to the next submenu.
To define the fixed value for the camera speed,
use the SEL and SET buttons and the handwheel, as
described above.
83
Controlling the Shutter Angle
84
<)
comp. User
fps
5.6.3 Shutter angle /
compensation user
Using the handwheel, the mirror shutter angle can be
manually adjusted within the user-defined end-stops,
simultaneously together with the values for the camera
speed and the iris (if controlled by the WRC-1).
If appropriate values are selected, either the exposure can
be kept at a constant level, or an adjustment process can
be defined to change the exposure as required (e.g.
fading in or out).
Note:
fps
The function of the user mode always remains
the same, irrespective of the position of the
WRC rotary switch (Iris, ) or fps): The timing
of the simultaneous adjustment processes is
controlled using the handwheel.
If a ramp function is selected (ramp Iris, ramp )
or ramp fps), a ramp duration can be defined.
In this case the handwheel is without function in
the main menu.
Differences in exposure are not automatically
compensated for.
The main menu shows the symbol ’ ) ‘ and the currently
adjusted shutter angle in the first display line. If the iris is
also controlled by the WRC-1, this is indicated by an ‘F’
at the end of the first display line. The currently adjusted
T-stop can be shown in the first display line by pressing
the SET button. The currently adjusted camera speed is
shown in the second display line.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
user mode
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
Controlling the Shutter Angle
In the user mode, all adjustments are not
carried out linearly within the adjustment time,
as in the other WRC modes. For this reason,
ramp durations may be different, compared to
those in the other WRC modes.
85
Controlling the Shutter Angle
86
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button (if controlled by the WRC-1). The
iris remains open until the OPEN button is
released again. This does not alter the programmed settings. The OPEN button is without
function while the camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The end-stops for the handwheel
(minimum and maximum shutter angle) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
aperture (if controlled by the WRC-1), use the SEL and
SET buttons and the handwheel, as described above.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• If the defined values result in a constant exposure, the
display shows ‘CONST LIGHT’ when the MODE button
is pressed. If this reading is not shown, the exposure is
altered while the handwheel is adjusted.
• Press the MODE button to go back to the main menu.
Controlling the Shutter Angle
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
camera speed, use the SEL and SET buttons and the
handwheel.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
87
Controlling the Shutter Angle
88
ramp <)
comp. off
PROG
PROG
PROG
5.6.4 Ramp shutter angle /
compensation off
The mirror shutter angle is continuously adjusted within
the pre-defined limit values over a pre-defined period of
time after pressing the RAMP button in the camera run
(ramp, definition see Glossary).
Differences in exposure are not automatically
compensated for.
fps
PROG
The main menu shows the current mirror shutter angle in
the first display line and ‘RA’ for the ramp function in the
second line.
The ‘PROG’ symbol indicates that the time-controlled
ramp function has been selected.
By pressing the SET button, the currently set T-stop can be
shown in the first display line (if controlled by the WRC-1),
and the currently set camera speed is shown in the
second display line.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum shutter angle can be defined.
The first display line shows the start value of the
shutter angle, and the second line the value at the end
of the ramp.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
Controlling the Shutter Angle
Note
89
Controlling the Shutter Angle
90
• Press the MODE button to go to the next submenu.
To define the fixed values for the aperture of the lens
(if controlled by the WRC-1) and the camera speed,
use the SEL and SET buttons and the handwheel, as
described above.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the MODE button to go back to the main menu.
Controlling the Shutter Angle
Note:
91
Controlling the Shutter Angle
92
ramp <)
comp. Iris
PROG
PROG
PROG
PROG
fps
PROG
5.6.5 Ramp shutter angle /
compensation iris
The shutter angle is continuously adjusted within the predefined limit values over a pre-defined period of time
after pressing the RAMP button in the camera run
(master value: Shutter angle).
The iris of the lens is automatically adjusted by the WRC-1
within the pre-defined limit values to compensate the
exposure. The visible depth of field can be altered with
this function.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
In the main menu the current shutter angle is shown in the
first display line. The automatically calculated T-stop is
shown in the second line.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button. The iris remains open until the
OPEN button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Shutter Angle
By pressing the SET button, the currently set camera speed
can be shown in the second display line.
93
Controlling the Shutter Angle
94
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum shutter angle can be defined.
The first display line shows the start value of the shutter
angle, and the second line the value at the end of the
ramp.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
If the compensation range available with the
iris ring is exceeded, the READY LED flashes
green and the warning ‘IRIS RANGE’ flashes on
the display after returning to the main menu.
The settings for the iris or the shutter angle must
be corrected accordingly! The camera can still
be started for test purposes in spite of the
flashing warning. However, the exposure may
be incorrect!
• Press the MODE button to go to the next submenu.
The limit values for the aperture can be defined.
The iris is automatically adjusted by the WRC-1 to
compensate the exposure, while the shutter angle is
ramped. One of the two limit values (minimum or
maximum aperture, depending on the adjustment
direction of the shutter angle) can be defined; the other
limit value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the T-stop
value flashes in the first or second display line. This
can now be set using the handwheel. The automatically
calculated other limit value is shown in the other display
line. Press the SEL button again to switch to the decimal.
The T-stop value is confirmed, and the decimal is set to
‘0’, by pressing the SET button.
• Press the MODE button to go to the next submenu.
To enter the fixed value for the camera speed, use the
SEL and SET buttons and the handwheel.
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the MODE button to go back to the main menu.
Controlling the Shutter Angle
The maximum aperture (smallest T-stop number)
corresponds to the selected minimum shutter angle.
95
Controlling the Shutter Angle
96
ramp <)
comp. User
PROG
fps
PROG
PROG
PROG
fps
PROG
PROG
PROG
5.6.6 Ramp shutter angle /
compensation user
The shutter angle is continuously adjusted, simultaneously
together with the aperture (if controlled by the WRC-1)
and the camera speed, within the freely definable limits
over a pre-defined period of time after pressing the
RAMP button in the camera run. If appropriate values are
selected, either the exposure can be kept at a constant
level, or a ramp can be defined to change the exposure
as required (e.g. fading in or out).
Note:
The function of the user mode always remains
the same, irrespective of the position of the
WRC rotary switch (Iris, ) or fps): The timing
of the simultaneous adjustment processes is
controlled using the handwheel.
If a ramp function is selected (ramp Iris, ramp )
or ramp fps), a ramp duration can be defined.
The ramp is started while the camera is running
by pressing the RAMP button. In this case the
handwheel is without function in the main menu.
Differences in exposure are not automatically
compensated for.
The main menu shows the symbol ’ ) ‘ and the currently
adjusted shutter angle in the first display line. If the iris is
controlled by the WRC-1, this is indicated by an ‘F’ at the
end of the first display line. The currently adjusted T-stop
can be shown in the first display line by pressing the SET
button. The current camera speed is displayed in the
second display line.
Note:
Note:
The display shows full T-stops followed by the
tenth of a T-stop. Example: T-stop 2.8 plus half
a T-stop is shown as 2.8_5. The tenths of a T-stop
are linearly divided between the two full T-stop
positions.
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN
button (if controlled by the WRC-1). The iris
remains open until the OPEN button is released
again. This does not alter the programmed
settings. The OPEN button is without function
while the camera is running.
user mode
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
Controlling the Shutter Angle
In the user mode, all adjustments are not
carried out linearly within the adjustment time,
as in the other WRC modes. For this reason,
ramp durations may be different, compared to
those in the other WRC modes.
97
Controlling the Shutter Angle
98
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
camera speed, use the SEL and SET buttons and the
handwheel. The first display line shows the start value
of the camera speed, and the second line the value at
the end of the ramp.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
• If the defined values result in a constant exposure, the
display shows ‘CONST LIGHT’ when the MODE button
is pressed. If this reading is not shown, the exposure is
altered during the ramp.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
aperture (if controlled by the WRC-1), use the SEL and
SET buttons and the handwheel, as described above.
The first display line shows the start value of the aperture,
and the second line the value at the end of the ramp.
Controlling the Shutter Angle
• Press the MODE button in the main menu to enter the
first submenu. The limit values (minimum and maximum
shutter angle) can be defined.
The first display line shows the start value of the shutter
angle, the second line shows the value at the end of
the ramp.
99
Controlling the Shutter Angle
100
• Press the MODE button to go to the next submenu. To
enter the ramp duration, use the SEL and SET buttons
and the handwheel as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
Note:
While the ramp duration is being set, the
display shows the automatically calculated
screen time in the first display line, which
corresponds to the selected projection speed
(see the next two bullet points).
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Shutter Angle
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
101
Controlling the Camera Speed
102
fps
fps
fps
fps
fps
fps
fps
comp. off
comp. Iris
comp. <)
comp.Iris <) 50%
comp.max. Iris
comp.max. <)
comp.user
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
ramp fps
ramp fps
ramp fps
ramp fps
ramp fps
ramp fps
comp.off
comp.Iris
comp.<)
comp.Iris/<)50%
comp.max. Iris
comp.max.<)
comp.user
PROG
fps
PROG
fps
PROG
fps
PROG
fps
PROG
fps
PROG
fps
PROG
PROG
fps
fps
PROG
fps
PROG
fps
PROG
PROG
fps
fps
PROG
PROG
fps
fps
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
Controlling the Camera Speed
ramp fps
103
Controlling the Camera Speed
104
5.7 Controlling the camera speed
5.7.1 Speed / compensation off
The camera speed can be manually adjusted within the
pre-defined end-stops of the handwheel.
Differences in exposure are not automatically
compensated for.
The main menu shows ‘SPEED’ in the first display line,
and the currently adjusted camera speed in the second
display line.
By pressing the SET button, the currently set shutter angle
(if controlled by the WRC-1) can be shown in the first
display line and the currently set T-stop (if controlled by
the WRC-1) is shown in the second display line.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
• Press the MODE button in the main menu to enter the
first submenu. The end-stops for the handwheel (minimum and maximum camera speed) can be defined.
The first display line shows the value for the left
handwheel end-stop, the second line shows the value
for the right end-stop.
fps
comp. off
fps
fps
• Press the MODE button to go to the next submenu.
To define the fixed values for the mirror shutter angle
(if controlled by the WRC-1) and the aperture of the
lens (if controlled by the WRC-1), use the SEL and SET
buttons and the handwheel, as described above.
If the aperture of the lens is controlled by the WRC-1,
the display shows full T-stops followed by the tenth of
a T-stop. Example: T-stop 2.8 plus half a T-stop is
shown as 2.8_5. The tenths of a T-stop are linearly
divided between the two full T-stop positions.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the next digit. The first
digits are confirmed, and the decimal positions are set
to ‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
105
Controlling the Camera Speed
106
fps
5.7.2 Speed / compensation iris
comp. Iris
fps
fps
The camera speed can be manually adjusted within the
pre-defined end-stops of the handwheel
(master value: Camera speed).
The exposure is automatically compensated for with the
iris of the lens while the camera speed is adjusted with the
handwheel.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The first line of the main menu shows the aperture of the lens,
which is automatically calculated within the pre-defined
limits. The second line shows the currently adjusted
camera speed using the handwheel. The display shows full
T-stops followed by the tenth of a T-stop. Example: T-stop
2.8 plus half a T-stop is shown as 2.8_5. The tenths of a
T-stop are linearly divided between the two full T-stop
positions.
By pressing the SET button, the currently set shutter angle
(if controlled by the WRC-1) can be shown in the first
display line.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
Note
107
Controlling the Camera Speed
108
• Press the MODE button in the main menu to enter the
first submenu. The end-stops for the handwheel (minimum and maximum camera speed) can be defined.
The first display line shows the value for the left
handwheel end-stop, the second line shows the value
for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the next digit. The first
digits are confirmed, and the decimal positions are set
to ‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the aperture of the lens can be
defined.
The aperture is automatically adjusted by the WRC-1
for a constant exposure, while the camera speed is
adjusted with the handwheel. One of the two limit
values (minimum or maximum aperture, depending on
the adjustment direction of the camera speed) can be
defined; the other limit value is automatically calculated
by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the T-stop
display flashes in the first or second display line. This
can now be set using the handwheel. The automatically calculated other limit value is shown in the other
display line. Press the SEL button again to switch to the
next digit. The selected T-stop is confirmed and the
decimal set to ‘0’ by pressing the SET button.
The full aperture (smallest T-stop number) corresponds
to the selected maximum camera speed.
• Press the MODE button to go to the next submenu.
To define the fixed value for the mirror shutter angle (if
controlled by the WRC-1), use the SEL and SET buttons
and the handwheel, as described above.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
If the compensation range available for the iris
ring is exceeded (e.g. the start T-stop is at the
beginning or end of the adjustment range), the
READY LED flashes green and the warning ‘IRIS
RANGE’ flashes on the display after returning
to the main menu. The setting for the iris or the
camera speed must be corrected! The camera
can still be started for test purposes in spite of
the flashing warning. However, the exposure
may be incorrect!
109
Controlling the Camera Speed
110
fps
comp. <)
fps
fps
5.7.3 Speed /
compensation shutter angle
The camera speed can be manually adjusted within the
pre-defined end-stops of the handwheel
(master value: Camera speed).
The exposure is automatically compensated for with the
mirror shutter angle.
If the electronic shutter angle control on the camera has
been switched off (the shutter angle has been set manually),
the warning ‘OFF ANGLE’ flashes in the main menu.
Switch on the electronic shutter angle control on the
camera (see camera instruction manual).
The first line of the main menu shows the mirror shutter angle,
which is automatically calculated within the per-defined
limits. The second line shows the currently adjusted
camera speed using the handwheel.
By pressing the SET button, the currently set T-stop (if
controlled by the WRC-1) can be shown in the first
display line.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the left and right
end-stop of the handwheel (minimum and maximum
camera speed) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the next digit. The first
digits are confirmed, and the decimal positions are set
to ‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the mirror shutter angle can be
defined.
The shutter angle is automatically adjusted to compensate
the exposure while the camera speed is adjusted with the
handwheel. One of the two limit values (minimum or
maximum shutter angle, depending on the adjustment
direction of the camera speed) can be defined; the other
limit value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the shutter
angle display flashes in the first or second display line.
This can now be set using the handwheel. The automatically calculated other limit value is shown in the other
display line. Press the SEL button again to switch to the
next digit. The selected shutter angle is confirmed and
the decimal is set to ‘0’ by pressing the SET button.
The minimum shutter angle corresponds to the selected
minimum camera speed.
Controlling the Camera Speed
Note
111
Controlling the Camera Speed
112
If the compensation range available for the shutter
angle is exceeded (e.g. the start shutter angle is
at the beginning or end of the adjustment range),
the READY LED flashes green and the warning
‘ANGLE RANGE’ flashes on the display after
returning to the main menu mode. The limits for
the shutter angle range or the camera speed
must be corrected! The camera can still be
started for test purposes in spite of the flashing
warning. However, the exposure may be incorrect!
• Press the MODE button to go to the next submenu.
To define the fixed value for the aperture of the lens (if
controlled by the WRC-1), use the SEL and SET buttons
and the handwheel, as described above.
• Press the MODE button to go back to the main menu.
fps
comp.Iris <) 50%
fps
fps
The camera speed can be manually adjusted within the
pre-defined end-stops of the handwheel
(master value: Camera speed).
The exposure is automatically compensated for with the
iris and the shutter angle at equal proportions.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The first line of the main menu shows the mirror shutter angle,
which is automatically adjusted within the pre-defined
limit values. The symbol ‘F’ at the end of the first line
indicates the additional control of the iris. The second line
shows the currently adjusted camera speed using the
handwheel.
By pressing the SET button, the automatically adjusted
T-stop can be shown in the first display line. The display
shows full T-stops followed by the tenth of a T-stop.
Example: T-stop 2.8 plus half a T-stop is shown as 2.8_5.
The tenths of a T-stop are linearly divided between the
two full T-stop positions.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
Controlling the Camera Speed
5.7.4 Speed / compensation iris and shutter angle 50%
113
Controlling the Camera Speed
114
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the left and right
end-stop of the handwheel (minimum and maximum
camera speed) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the next digit. The first
digits are confirmed, and the decimal positions are set
to ‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the mirror shutter angle can be
defined.
Both the mirror shutter angle and the aperture are
automatically adjusted as an exposure compensation
while the camera speed adjusted with the handwheel.
One of the two limit values (minimum or maximum
shutter angle, depending on the adjustment direction
of the camera speed) can be defined; the other limit
value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the shutter
angle display flashes in the first or second display line.
This can now be set using the handwheel. The automatically calculated other limit value is shown in the
other display line.
Press the SEL button again to switch to the next digit.
The selected shutter angle is confirmed and the
decimal is set to ‘0’ by pressing the SET button.
The minimum shutter angle corresponds to the selected
minimum camera speed.
• Press the MODE button to go to the next submenu.
To define the adjustment range for the aperture of the
lens, use the SEL and SET buttons and the handwheel,
as described above.
If the compensation range available with the
aperture is exceeded, the READY LED flashes
green and the warning ‘IRIS RANGE’ flashes on
the display after returning to the main menu.
The limit values for the iris or the camera speed
must be corrected! The camera can still be started
for test purposes in spite of the flashing warning. However, the exposure may be incorrect!
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
If the compensation range available for the shutter
angle is exceeded (e.g. the start shutter angle is
at the beginning or end of the adjustment range),
the READY LED flashes green and the warning
‘ANGLE RANGE’ flashes on the display after
returning to the main menu. The limit values for
the shutter range or the camera speed must be
corrected! The camera can still be started for
test purposes in spite of the flashing warning.
However, the exposure may be incorrect!
115
Controlling the Camera Speed
116
fps
comp.max. Iris
fps
fps
5.7.5 Speed /
compensation max. iris
The camera speed can be manually adjusted within the
pre-defined end-stops of the handwheel
(master value: Camera speed).
The exposure is automatically compensated for by
adjusting the aperture of the lens. If the adjustment range
of the iris is not sufficient for the given end values, the rest
will be compensated for by the mirror shutter. In this case,
the shutter angle proportion is evenly distributed over the
entire compensation range.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The first line of the main menu shows the symbol ’ ) ‘ for
the adjustment of the mirror shutter angle and the T-stop
of the lens, which is automatically adjusted within the predefined limit values. The second line shows the currently
adjusted camera speed using the handwheel.
The display shows full T-stops followed by the
tenth of a T-stop. Example: T-stop 2.8 plus half
a T-stop is shown as 2.8_5. The tenths of a T-stop
are linearly divided between the two full T-stop
positions.
By pressing the SET button, the automatically adjusted
mirror shutter angle can be shown in the first display line.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
Note:
117
Controlling the Camera Speed
118
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the left and right
end-stop of the handwheel (minimum and maximum
camera speed) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the other positions. The
first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the aperture of the lens can be defined.
Both the aperture and the shutter angle (if necessary)
are automatically adjusted to compensate the exposure
while the camera speed is adjusted with the handwheel.
The two limit values (minimum and maximum T-stop)
can be selected as required.
Press the SEL button for longer than 2 seconds.
The T-stop value in the first display line flashes.
This can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
If the compensation range available with the shutter
angle is exceeded, the READY LED flashes green
and the warning ‘ANGLE RANGE’ flashes on the
display after returning to the main menu. The
limit values for the iris, the shutter angle or the
camera speed must be corrected! The camera
can still be started for test purposes in spite of
the flashing warning. However, the exposure
may be incorrect!
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
To define the adjustment range for the mirror shutter
angle, use the SEL and SET buttons and the handwheel,
as described above.
One of the two limit values (minimum or maximum
shutter angle, depending on the adjustment direction
of the camera speed) can be defined; the other limit
value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the shutter
angle display flashes in the first or second display line.
This can now be set using the handwheel.
The automatically calculated other limit value is shown
in the other display line. Press the SEL button again to
switch to the next digit. The selected shutter angle is
confirmed and the decimal is set to ‘0’ by pressing the
SET button.
The minimum shutter angle corresponds to the selected
minimum camera speed.
119
Controlling the Camera Speed
120
fps
comp.max. <)
fps
fps
5.7.6 Speed /
compensation max. shutter angle
The camera speed can be manually adjusted within the
pre-defined end-stops of the handwheel
(master value: Camera speed).
The exposure is automatically compensated for by
adjusting the mirror shutter angle. If the adjustment range
of the shutter angle is insufficient for the given end value,
the rest will be compensated for by the aperture of the
lens. In this case, the iris proportion is evenly distributed
over the entire compensation range.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The first line of the main menu shows the mirror shutter
angle, which is automatically adjusted within the the predefined limit values.
The symbol ‘F’ indicates the additional adjustment of the
iris at the end of the first display line.
The second display line shows the currently adjusted
camera speed using the handwheel.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
By pressing the SET button, the automatically adjusted
T-stop can be shown in the first display line. The display
shows full T-stops followed by the tenth of a T-stop.
Example: T-stop 2.8 plus half a T-stop is shown as 2.8_5.
The tenths of a T-stop are linearly divided between the
two full T-stop positions.
121
Controlling the Camera Speed
122
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the left and right
end-stop of the handwheel (minimum and maximum
camera speed) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the next digit. The first
digits are confirmed, and the decimal positions are set
to ‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
• Press the MODE button to go to the next submenu. The
limit values for the mirror shutter angle can be defined.
Both the mirror shutter angle and the aperture of the
lens (if necessary) are automatically adjusted to
compensate the exposure while the camera speed is
adjusted with the handwheel.
The two limit values (minimum and maximum shutter
angle) can be selected as required.
Press the SEL button for longer than 2 seconds.
The shutter angle shown in the first display line
flashes. This can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
The first display line shows the value for the left
handwheel end-stop, the second line shows the value
for the right end-stop.
If the compensation range available with the
aperture is exceeded (e.g. the start value is at
the beginning or end of the adjustment range)
the READY LED flashes green and the warning
‘IRIS RANGE’ flashes on the display after
returning to the main menu.
The limit values for the shutter angle, the iris or
the camera speed must be corrected! The
• Press the MODE button to go to the next submenu.
The limit values for the iris can be defined using the
SEL and SET buttons and the handwheel.
One of the two limit values (minimum or maximum
aperture, depending on the adjustment direction of the
camera speed) can be defined; the other limit value is
automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the T-stop
display flashes in the first or second display line.
This can now be set using the handwheel.
The automatically calculated other limit value is shown
in the other display line. Press the SEL button again to
switch to the next digit. The selected T-stop is confirmed
and the decimal is set to ‘0’ by pressing the SET button.
The full aperture (smallest T-stop number) corresponds
to the selected maximum camera speed.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
camera can still be started for test purposes in
spite of the flashing warning. However, the
exposure may be incorrect!
123
Controlling the Camera Speed
124
fps
comp.user
fps
fps
5.7.7 Speed /
compensation user
Using the handwheel, the camera speed can be manually
adjusted within the pre-defined end-stops, simultaneously
together with the values for the shutter angle
(if controlled by the WRC-1) and the iris (if controlled by
the WRC-1).
If appropriate values are selected, either the exposure can
be kept at a constant level, or an adjustment process can
be defined to change the exposure as required (e.g.
fading in or out).
Note:
The function of the user mode always remains
the same, irrespective of the position of the
WRC rotary switch (Iris, ) or fps): The timing
of the simultaneous adjustment processes is
controlled using the handwheel.
If a ramp function is selected (ramp Iris, ramp )
or ramp fps), a ramp duration can be defined.
In this case the handwheel is without function in
the main menu.
Differences in exposure are not automatically
compensated for.
The first line of the main menu shows the currently adjusted
shutter angle (if controlled by the WRC-1).
If the iris is controlled by the WRC-1, this is indicated by
an ‘F’ at the end of the first display line. By pressing the
SET button, the currently adjusted aperture can be shown
in the first display.
The second line shows the currently adjusted camera speed.
Note:
Note
The display shows full T-stops followed by the
tenth of a T-stop. Example: T-stop 2.8 plus half a
T-stop is shown as 2.8_5. The tenths of a T-stop
are linearly divided between the two full T-stop
positions.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
user mode
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
Controlling the Camera Speed
In the user mode, all adjustments are not
carried out linearly within the adjustment time,
as in the other WRC modes. For this reason,
ramp durations may be different, compared to
those in the other WRC modes.
125
Controlling the Camera Speed
126
Note:
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN
button (if controlled by the WRC-1). The iris
remains open until the OPEN button is released
again. This does not alter the programmed
settings. The OPEN button is without function
while the camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the left and right
end-stops of the handwheel (minimum and maximum
camera speed) can be defined.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash. The required
value can now be set using the handwheel. Press the
SEL button again to switch to the next digit. The first
digits are confirmed, and the decimal positions are set
to ‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
shutter angle (if controlled by the WRC-1), use the SEL
and SET buttons and the handwheel, as described above.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
• If the defined values result in a constant exposure, the
display shows ‘CONST LIGHT’ when the MODE button
is pressed. If this reading is not shown, the exposure is
altered while the handwheel is adjusted.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
aperture of the lens (if controlled by the WRC-1), use
the SEL and SET buttons and the handwheel, as
described above.
The first display line shows the value for the left end-stop,
the second line shows the value for the right end-stop.
127
Controlling the Camera Speed
128
ramp fps
comp.off
PROG
fps
PROG
5.7.8 Ramp speed /
compensation off
The camera speed is continuously adjusted within the predefined limit values over a pre-defined period of time
after pressing the RAMP button in the camera run (ramp,
definition see Glossary).
fps
PROG
PROG
PROG
Differences in exposure are not automatically
compensated for.
The first line of the main menu shows ‘RA’ to indicate the
ramp function, and the active camera speed in the second
line.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
By pressing the SET button, the currently set shutter angle
(if controlled by the WRC-1) can be shown in the first
display line, and the currently set aperture (if controlled
by the WRC-1) in the second display line.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum camera speed can be defined.
The first display line shows the start value of the
camera speed, and the second line the value at the
end of the ramp.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digits.
The first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
Controlling the Camera Speed
Note
129
Controlling the Camera Speed
130
• Press the MODE button to go to the next submenu.
To define the fixed values for the mirror shutter angle
(if controlled by the WRC-1) and the aperture of the
lens (if controlled by the WRC-1), use the SEL and SET
buttons and the handwheel, as described above.
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
131
Controlling the Camera Speed
132
ramp fps
comp.Iris
PROG
fps
PROG
fps
5.7.9 Ramp speed /
compensation iris
The camera speed is continuously adjusted within the predefined limit values over a pre-defined period of time after
pressing the RAMP button in the camera run
(master value: Camera speed).
The iris is automatically adjusted by the WRC-1 within the
pre-defined limit values to compensate the exposure.
PROG
PROG
PROG
PROG
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The first line of the main menu shows the automatically
calculated T-stop. The current camera speed is shown in
the second line.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN
button. The iris remains open until the OPEN
button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
By pressing the SET button, the currently set shutter angle
(if controlled by the WRC-1) can be shown in the first
display line.
133
Controlling the Camera Speed
134
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum camera speed can be defined.
The first display line shows the start value of the camera
speed, and the second line the value at the end of the ramp.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the aperture can be defined.
The aperture is automatically adjusted by the WRC-1
to compensate the exposure while the camera speed is
ramped. One of the two limit values (minimum or maximum aperture, depending on the adjustment direction
of the camera speed) can be defined; the other limit
value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the T-stop
value flashes in the first or second display line.
This can now be set using the handwheel. The automatically
calculated other limit value is shown in the other display
line. Press the SEL button again to switch to the next digit.
The T-stop value is confirmed, and the decimal is set to
‘0’, by pressing the SET button.
The full aperture (smallest T-stop number) corresponds
to the selected maximum camera speed.
If the compensation range available with the
aperture is exceeded, the READY LED flashes green
and the warning ‘IRIS RANGE’ flashes on the
display after returning to the main menu. The
limit values for the iris or the camera speed must
be corrected! The camera can still be started for
test purposes in spite of the flashing warning.
However, the exposure may be incorrect!
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
To define the fixed value for the mirror shutter angle (if
controlled by the WRC-1), use the SEL and SET buttons
and the handwheel, as described above.
135
Controlling the Camera Speed
136
ramp fps
comp.<)
PROG
fps
PROG
fps
PROG
PROG
PROG
PROG
5.7.10 Ramp speed /
compensation shutter angle
The camera speed is continuously adjusted within the predefined limit values over a pre-defined period of time after
pressing the RAMP button in the camera run
(master value: Camera speed).
The mirror shutter angle is automatically adjusted by the
WRC-1 within the pre-defined limit values, to compensate
the exposure.
The first line of the main menu shows the automatically
calculated value of the shutter angle. The current camera
speed is shown in the second line.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
By pressing the SET button, the currently set T-stop (if
controlled by the WRC-1) can be shown in the first display
line. The display shows full T-stops followed by the tenth
of a T-stop. Example: T-stop 2.8 plus half a T-stop is
shown as 2.8_5. The tenths of a T-stop are linearly
divided between the two full T-stop positions.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris
can be opened completely by pressing the
OPEN button. The iris remains open until the
OPEN button is released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
Note
137
Controlling the Camera Speed
138
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum camera speed can be defined.
The first display line shows the start value of the
camera speed, and the second line the value at the
end of the ramp.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digits.
The first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the shutter angle can be defined.
The shutter angle is automatically adjusted by the WRC-1
to compensate the exposure while the camera speed is
ramped. One of the two limit values (minimum or
maximum shutter angle, depending on the adjustment
direction of the camera speed) can be defined; the
other limit value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the shutter
angle value flashes in the first or second display line.
This can now be set using the handwheel. The automatically calculated other limit value is shown in the
other display line. Press the SEL button again to switch
to the next digit. The shutter angle value is confirmed,
and the decimal is set to ‘0’, by pressing the SET button.
The minimum shutter angle (smallest shutter angle)
corresponds to the selected minimum camera speed.
If the compensation range available with the shutter
angle is exceeded, the READY LED flashes green
and the warning ‘ANGLE RANGE’ flashes on the
display after returning to the main menu. The limit
values for the shutter angle or the camera speed
must be corrected!
The camera can still be started for test purposes
in spite of the flashing warning. However, the
exposure may be incorrect!
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
To define the fixed value for the aperture of the lens (if
controlled by the WRC-1), use the SEL and SET buttons
and the handwheel, as described above.
139
Controlling the Camera Speed
140
ramp fps
comp.Iris/<)50%
5.7.11 Ramp speed /
compensation iris
and shutter angle 50%
PROG
fps
PROG
fps
PROG
PROG
PROG
PROG
The camera speed is continuously adjusted within the predefined limit values over a pre-defined period of time after
pressing the RAMP button in the camera run
(master value: Camera speed).
The iris of the lens and the mirror shutter angle are automatically adjusted by the WRC-1 to equal proportions within
the pre-defined limit values, to compensate the exposure.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
The first line of the main menu shows the automatically
calculated value of the shutter angle and the symbol ‘F’ to
indicate the iris control. The second line shows the current
camera speed.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before initating
the camera run!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN button.
The iris remains open until the OPEN button is
released again. This does not alter the programmed settings. The OPEN button is without
function while the camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
By pressing the SET button, the currently adjusted T-stop
can be shown in the first display line. The display shows
full T-stops followed by the tenth of a T-stop.
Example: T-stop 2.8 plus half a T-stop is shown as 2.8_5.
The tenths of a T-stop are linearly divided between the
two full T-stop positions.
141
Controlling the Camera Speed
142
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum camera speed can be defined.
The first display line shows the start value of the
camera speed, and the second line the value at the
end of the ramp.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digits.
The first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the shutter angle can be defined.
The shutter angle is automatically adjusted by the
WRC-1 to compensate the exposure while the camera
speed is ramped. One of the two limit values (minimum
or maximum shutter angle, depending on the adjustment
direction of the camera speed) can be defined; the other
limit value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the shutter
angle value flashes in the first or second display line.
This can now be set using the handwheel. The automatically calculated other limit value is shown in the
other display line. Press the SEL button again to switch
to the next digit. The shutter angle value is confirmed,
and the decimal is set to ‘0’, by pressing the SET button.
The minimum shutter angle (smallest shutter angle)
corresponds to the selected minimum camera speed.
• Press the MODE button to go to the next submenu.
The limit values of the aperture can be defined using
the SEL and SET buttons and the handwheel.
If the compensation range available with the
aperture is exceeded, the READY LED flashes
green and the warning ‘IRIS RANGE’ flashes on
the display after returning to the main menu.
The limit values for the shutter angle, the iris or
the camera speed must be corrected! The
camera can still be started for test purposes in
spite of the flashing warning. However, the
exposure may be incorrect!
Controlling the Camera Speed
If the compensation range available with the
shutter angle is exceeded, the READY LED flashes
green and the warning ‘ANGLE RANGE’ flashes
on the display after returning to the main menu.
The limit values for the shutter angle or the
camera speed must be corrected!
The camera can still be started for test purposes
in spite of the flashing warning. However, the
exposure may be incorrect!
143
Controlling the Camera Speed
144
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
145
Controlling the Camera Speed
146
ramp fps
comp.max. Iris
PROG
fps
PROG
fps
PROG
PROG
PROG
5.7.12 Ramp speed /
compensation max. iris
The camera speed is continuously adjusted within the predefined limit values over a pre-defined period of time
after the RAMP button is pressed in the camera run
(master value: Camera speed).
The aperture of the lens is automatically adjusted by the WRC-1
within the pre-defined limit values, to compensate the exposure.
If the adjustment range of the aperture is not sufficient for
the given end values, the rest will be compensated for by
the mirror shutter. In this case, the shutter angle proportion
is evenly distributed over the entire compensation range.
If the iris control is not available, the flashing warning
‘NO IRIS’ is displayed in the main menu. Connect the iris
control as described in chapter 4.1.2, calibrate the lens
and assign the T-stops as described in chapter 5.5.1!
PROG
The first line of the main menu shows the symbol ’ ) ’ to
indicate the shutter angle control, and the current T-stop,
which is automatically calculated. The second line shows
the current camera speed.
The display shows full T-stops followed by the tenth of a
T-stop. Example: T-stop 2.8 plus half a T-stop is shown as
2.8_5. The tenths of a T-stop are linearly divided between
the two full T-stop positions.
By pressing the SET button, the currently adjusted shutter
angle can be shown in the first display line.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera).
Readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN button.
The iris remains open until the OPEN button is
released again. This does not alter the programmed settings. The OPEN button is without
function while the camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
147
Controlling the Camera Speed
148
• Press the MODE button in the main menu to enter the
first submenu. The limit values for the minimum and
maximum camera speed can be defined.
The first display line shows the start value of the
camera speed, and the second line the value at the
end of the ramp.
• Press the SEL button for longer than 2 seconds.
The shutter angle value in the first display line flashes.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digits.
The first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button. The values in
the second display line can be set accordingly.
• Press the MODE button to go to the next submenu.
The limit values for the aperture of the lens can be
defined.
Both the iris and the shutter angle (only if necessary)
are automatically adjusted by the WRC-1 to compensate
the exposure while the camera speed is ramped.
The two limit values (minimum and maximum aperture)
can be selected as required.
Press the SEL button for longer than 2 seconds.
The T-stop value in the first display line flashes.
This can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button. The values in the
second display line can be set accordingly.
The first display line shows the start value of the aperture,
and the second line the value at the end of the ramp.
• Press the MODE button to go to the next submenu.
The limit values for the mirror shutter angle can be
defined using the SEL and SET buttons and the handwheel.
One of the two limit values (minimum or maximum
shutter angle, depending on the adjustment direction
of the camera speed) can be defined; the other limit
value is automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the shutter
angle value flashes in the first or second display line.
This can now be set using the handwheel.
The automatically calculated other limit value is shown
in the other display line.
Press the SEL button again to switch to the next digit.
The selected shutter angle is confirmed and the
decimal is set to ‘0’ by pressing the SET button.
The minimum shutter angle corresponds to the selected
minimum camera speed.
Controlling the Camera Speed
If the compensation range available with the
shutter angle is exceeded, the READY LED flashes
green and the warning ‘ANGLE RANGE’ flashes
on the display after returning to the main menu.
The limit values for the iris, the shutter angle or
the camera speed must be corrected! The
camera can still be started for test purposes in
spite of the flashing warning. However, the
exposure may be incorrect!
149
Controlling the Camera Speed
150
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
151
Controlling the Camera Speed
152
ramp fps
comp.max.<)
PROG
fps
PROG
fps
PROG
5.7.13 Ramp speed / compensation
max. shutter angle
The camera speed is continuously adjusted within the predefined limit values over a pre-defined period of time after
the RAMP button is pressed in the camera run (master value:
Camera speed). The mirror shutter angle is automatically
adjusted by the WRC-1 to compensate the exposure. If the
adjustment range of the shutter angle is insufficient for the
given end value, the rest will be compensated for by the
aperture of the lens. In this case, the aperture proportion
is evenly distributed over the entire compensation range.
PROG
PROG
PROG
The first line of the main menu shows the automatically
calculated value of the shutter angle and the symbol ‘F’ to
indicate the iris control. The second line shows the current
camera speed.
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
By pressing the SET button, the currently adjusted T-stop
can be shown in the first display line. The display shows
full T-stops followed by the tenth of a T-stop.
Example: T-stop 2.8 plus half a T-stop is shown as 2.8_5.
The tenths of a T-stop are linearly divided between the
two full T-stop positions.
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
Note:
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN button.
The iris remains open until the OPEN button is
released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
Controlling the Camera Speed
Note
153
Controlling the Camera Speed
154
• Press the MODE button in the main menu to enter the first
submenu. The limit values for the minimum and
maximum camera speed can be defined.
The first display line shows the start value of the
camera speed, and the second line the value at the
end of the ramp.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digits.
The first digits are confirmed, and the decimal positions
are set to ‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu. The
limit values for the mirror shutter angle can be defined.
Both the mirror shutter angle and the iris of the lens (if
necessary) are automatically adjusted to compensate
the exposure while the camera speed is ramped.
The two limit values (minimum and maximum shutter
angle) can be selected as required.
Press the SEL button for longer than 2 seconds.
The shutter angle shown in the first display line
flashes. This can now be set using the handwheel.
Press the SEL button again to switch to the next digit.
The first digits are confirmed, and the decimal is set to
‘0’ by pressing the SET button. The values in the second
display line can be set accordingly.
The first display line shows the start value of the ramp,
and the second line the end value.
• Press the MODE button to go to the next submenu.
The limit values for the aperture of the lens are defined,
using the SEL and SET buttons and the handwheel.
One of the two limit values (minimum or maximum
aperture, depending on the adjustment direction of the
camera speed) can be defined; the other limit value is
automatically calculated by the WRC-1.
Press the SEL button for longer than 2 seconds.
Depending on the definable limit value, the T-stop
value flashes in the first or second display line. This
can now be set using the handwheel.
The automatically calculated other limit value is shown
in the other display line.
Press the SEL button again to switch to the next digit.
The selected T-stop value is confirmed, and the decimal is set to ‘0’, by pressing the SET button.
The full aperture (smallest T-stop number) corresponds
to the selected maximum camera speed.
Controlling the Camera Speed
If the compensation range available with the
iris is exceeded (e.g. the start value is at the
beginning or end of the adjustment range) the
READY LED flashes green and the warning ‘IRIS
RANGE’ flashes on the display after returning
to the main menu. The limit values for the
shutter angle, the iris or the camera speed must
be corrected! The camera can still be started for
test purposes in spite of the flashing warning.
However, the exposure may be incorrect!
155
Controlling the Camera Speed
156
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
157
Controlling the Camera Speed
158
ramp fps
comp.user
PROG
fps
PROG
fps
PROG
PROG
PROG
PROG
5.7.14 Ramp speed /
compensation user
The camera speed is continuously adjusted, together with
the iris (if controlled by the WRC-1) and the mirror shutter
angle (if controlled by the WRC-1) within the freely
definable limits over a pre-defined period of time after
pressing the RAMP button in the camera run.
If appropriate values are selected, either the exposure can
be kept at a constant level, or a ramp can be defined to
change the exposure as required (e.g. fading in or out).
Note:
The function of the user mode always remains
the same, irrespective of the position of the
WRC rotary switch (Iris, ) or fps): The timing
of the simultaneous adjustment processes is
controlled using the handwheel.
If a ramp function is selected (ramp Iris, ramp )
or ramp fps), a ramp duration can be defined.
The ramp is started while the camera is running
by pressing the RAMP button. In this case the
handwheel is without function in the main menu.
Differences in exposure are not automatically
compensated for.
The main menu shows the currently adjusted shutter angle
in the first line. If the aperture is being controlled by the
WRC-1, this is indicated by an ‘F’ at the end of the first
display line. The currently adjusted T-stop can be shown
in the first display line by pressing the SET button.
The current camera speed is displayed in the second line.
Note:
Note:
The display shows full T-stops followed by the
tenth of a T-stop. Example: T-stop 2.8 plus half
a T-stop is shown as 2.8_5. The tenths of a T-stop
are linearly divided between the two full T-stop
positions.
To check the image in the viewfinder, the iris can
be opened completely by pressing the OPEN
button (if controlled by the WRC-1).
The iris remains open until the OPEN button is
released again.
This does not alter the programmed settings.
The OPEN button is without function while the
camera is running.
user mode
The ‘PROG’ symbol indicates that a time-controlled ramp
function has been selected.
Note
The following warnings may be displayed:
‘IRIS TBL’ – a valid iris table has not yet been
activated;
readings with ‘NO’ in the first display line
indicate that the selected function is currently
not available (example: ‘NO IRIS’ although the
iris control is activated on the WRC-1, the iris
motor has not yet been connected);
readings with ‘RANGE’ in the second display
line indicate that the adjustment range of a
Controlling the Camera Speed
In the user mode, all adjustments are not
carried out linearly within the adjustment time,
as in the other WRC modes. For this reason,
ramp durations may be different, compared to
those in the other WRC modes.
159
Controlling the Camera Speed
160
parameter has been exceeded (example: the
selected speed is not available with this camera);
readings with ‘OFF’ in the first display line
indicate that this function is deactivated on the
camera (example: shutter angle of the 435 is
set manually = ‘OFF ANGLE’).
Correct parameters must be set before the
camera is started!
The handwheel is without function in the main menu.
Press the RAMP button when the camera is running to
start the ramp. The camera can be started, by pressing
the RUN button on the WMU-1.
The ramp can be reversed, by pressing the RAMP button
again: the ramp then reverses its direction until it reaches
the start value again. For best results wait until the end of
the ramp.
With most lenses, the T-stops before the end-stops
are not exact due to the tolerances involved. In
order to avoid incorrect exposure, the adjusted
iris range should not contain these values.
With the iris wide open a lens-related reduction
in brightness towards the edge of the image
may occur, looking like an incorrect exposure.
The exact values are dependent on the lens type
and must be determined with test shots.
• Press the MODE button in the main menu to enter the
first submenu. The limit values (minimum and maximum
camera speed) can be defined.
The first display line shows the start value of the
camera speed, and the second line the value at the
end of the ramp.
• Press the SEL button for longer than 2 seconds.
The first digits in the first display line flash.
The required value can now be set using the handwheel.
Press the SEL button again to switch to the next digits.
The first digits are confirmed, and the decimal positions are set to ‘0’ by pressing the SET button.
The values in the second display line can be set
accordingly.
• Press the MODE button to go to the next submenu.
To define the values for the aperture of the lens (if
controlled by the WRC-1), use the SEL and SET buttons
and the handwheel, as described above.
The start value of the aperture is shown in the first display
line, and the end value is shown in the second line.
• If the defined values result in a constant exposure, the
display shows ‘CONST LIGHT’ when the MODE button
is pressed. If this reading is not shown, the exposure is
altered during the ramp.
Controlling the Camera Speed
• Press the MODE button to go to the next submenu.
To define the values for the minimum and maximum
shutter angle (if controlled by the WRC-1), use the SEL
and SET buttons and the handwheel, as described above.
The start value of the shutter angle is shown in the first
display line, and the end value is shown in the second line.
161
Controlling the Camera Speed
162
• Press the MODE button to go to the next submenu.
To enter the ramp duration, use the SEL and SET
buttons and the handwheel, as described above.
A previously set ramp duration may now exceed
the technically fastest possible adjustment, if the
ramp duration is simply kept from an old
program. The READY LED then flashes green
and the warning ‘SEC RANGE’ is shown in the
main menu. The ramp duration must be corrected. The camera can still be started for test
purposes in spite of the flashing warning.
However, the exposure may be incorrect!
Note:
The shortest possible ramp time is adjusted by
turning the handwheel to the left end-stop. The
maximum ramp time is 100 seconds.
Note:
While the ramp duration is being set, the display
shows the automatically calculated screen time
in the first display line, which corresponds to the
selected projection speed (see the next two
bullet points).
• Press the MODE button to go to the next submenu.
The screen time for the selected ramp duration can be
displayed.
The screen time is the time (in seconds) needed for a
projection at a selected standard projection speed:
24, 25 and 30 fps are available.
• Press the SEL button for longer than 2 seconds to select
the required projection speed. Press the SEL button
repeatedly to switch between the three available values.
The selected projection speed is confirmed by pressing
the SET button.
• Press the MODE button to go back to the main menu.
Warnings are only displayed in the WRC mode, and only
in the main menu ➪ photo (indicated by a black bar in
the top right of the display). In CAM mode, only warnings
are displayed, which also appear on the camera display.
All flashing displays (including LEDs) indicate a warning.
Note:
black indicator bar for main menu
Warnings
6. Warnings
All warnings displayed on the WMU-1 are
described in the LCS Manual
A function has been selected which cannot technically
be realised.
Example: the iris adjustment cannot be compensated for
a constant exposure at the same time by the iris (or a
function in combination with the iris, e.g. iris / ) 50 %).
Set a permitted combination using the
WRC and COMPENSATION rotary switches.
163
Warnings
The connected camera is in the program mode;
the program activated in the camera has priority.
The camera program must be deactivated if the WRC-1 is
to be used for controlling (see Camera instruction manual).
A single frame unit is attached to the camera.
The single frame unit controls the mirror shutter and the
camera speed.
The single frame unit must be deactivated if the WRC-1
is to be used for controlling.
(see Single Frame/Capping Shutter instruction manual).
An ESU-1 or VSU is connected to the camera.
These units control the corresponding camera functions.
The ESU-1 or VSU must be disconnected from the
camera if the WRC-1 is to be used for controlling.
Warning: risk of improper use!
A SCU is connected to the camera.
This unit controls the corresponding camera functions.
The SCU must be disconnected from the camera if the
WRC-1 is to be used for controlling.
Warning: risk of improper use!
164
Warnings
The selector switch on the camera is not set to PS/CCU
(or to CCU on the ARRIFLEX 535A).
Set the camera selector switch to PS/CCU.
With the ARRIFLEX 535A only a fixed reverse speed of
25 fps is available via the WRC-1.
The connected camera does not have an electronically
adjustable mirror shutter. The exposure cannot be
compensated for using the mirror shutter.
Another kind of compensation must be selected using
the COMPENSATION rotary switch.
The electronic shutter angle adjustment on the camera is
deactivated – the shutter angle has been mechanically set.
Release the mechanical locking of the shutter angle and
switch on the electronic shutter angle control on the camera.
ft
m
h:min
TC UB
fpsR
sec:f
1
5
2
6
3
7
4
8
filter
jam
PROG asy
end
bat
165
Warnings
No iris motor is connected to the UMC-1,
a CLM-1 is connected as the iris motor,
or the IRIS sliding switch is set to OFF and a function has
been selected which requires the iris to be controlled
or the calibration process is running.
Connect a CLM-2 iris motor,
or set the IRIS sliding switch to ON and then switch the
WRC-1 (and WMU-1) off and on again to reset the units,
or select a WRC function which does not require an iris
control.
Command to calibrate the lens.
Press the CAL button on the WMU-1.
An iris table is not activated.
Connect the iris control as described in chapter 4.1.2,
calibrate the lens and assign the T-stops as described in
chapter 5.5.1!
166
The ramp time cannot be executed for technical reasons.
Set an executable (longer) ramp time.
Warnings
The programmed camera speed values lie outside of the
available range
(e.g. the WRC-1 has been programmed for a highspeed camera, but a standard model is now connected).
An adjusted shutter angle value,
or the automatically calculated angle,
lies outside of the available range.
Set executable limit values for the shutter angle range.
The adjusted iris limit values
or end-stops lie outside of the adjustment range of the iris.
Define new iris limit values or end-stops.
167
Warnings
Warnings when programming iris tables
A T-stop has been programmed which cannot be
correct, e.g. T-stop 2.0 cannot lie between 2.8 and 4.
The incorrectly positioned value must be deleted
and reset.
ft
m
h:min
TC UB
fpsR
sec:f
1
5
2
6
3
7
4
8
filter
jam
PROG asy
end
bat
The adjustment range of the iris ring is not compatible
with the selected lens even though it has been re-calibrated.
The selected lens is not compatible with the adjustment
range of the choosen lens.
Use the correct lens,
or select the right lens when programming.
If the device is checked and found to be set properly,
either the end-stops of the lens have probably been reset
or another iris ring has been mounted. In this case, the
lens can be programmed in the user mode (see chapter
5.5.1.2 Programming iris tables for other lenses).
168
The loaded table contains an error,
or it is not compatible with the lens
mounted on the camera.
Re-program the T-stops.
Warnings
The T-stop value set on the lens lies outside
of the permitted range.
Reset the T-stop on the lens.
169
Quick Guide
CLM-2
535, 535B, 435, 16 SR3
RS
RF
CAL
BAT RDY
RUN
UC-C1
LENS CONTROL SYSTEM
WMU-1 + WRC-1
170
UMC-1 + URM-1
UC-R1
CCU
This quick guide is aimed at users who have
already read the instruction manual, and who
are very familiar with the system.
Warning: no reference is made in this chapter
to possible operating errors – this chapter
therefore does not include any warnings!
7.1 Connecting the devices
System components required
for wireless operation
WRC-1 .................................................... K2.52087.0
WMU-1 ................................................... K2.52052.0
with WBU-2 battery .................................. K2.52088.0
WAC-1 charger ........................................ K2.52072.0
UMC-1 .................................................... K2.52040.0
with UC-C1 cable [K2.52047.0 as replacement]
dovetail adapter ....................................... K2.52080.0
URM-1 ..................................................... K2.52048.0
UC-R1 cable ............................................. K2.52079.0
for iris control additionally
CLM-2 ..................................................... K2.52036.0
possibly with console ................................. K2.52035.0
Note:
CLM-1 motors cannot be used as iris motors
for the WRC-1.
• In order to operate the WRC-1 the following EPROM
versions must be used:
WMU: ........................................... 01.50 or higher
UMC: ............................................. 01.50 or higher
ARRIFLEX 435 .................................... 2.4 or higher
Quick Guide
7. Quick guide
The dovetail adapter (K2.52080.0) can be used to firmly
attach the UMC-1 to the camera.
The UC-C1 cable links the UMC-1 and the RS socket on
the camera, while the UC-R1 cable connects the UMC-1
and the CCU socket. Set the PS-CCU/NORM switch on
the camera to PS-CCU.
System components required
for cable operation
WRC-1 .................................................... K2.52087.0
WC-W1-S cable ....................................... K2.52089.0
WHA-1 .................................................... K2.52070.0
171
7.2.1 CAM mode
IRIS sliding switch
Set the WRC/CAM sliding switch to CAM. In this operating
mode the display on the WRC-1 is identical to the camera
display. The settings on the camera can be adjusted by
pressing the MODE, SEL and SET buttons. The OPEN
button serves as the PHASE button on the camera.
WRC/CAM sliding switch
ON
READY
WRC CAM
OFF
IRIS
RUN
PROG
SEL button
MODE button
SET button
OPEN/PHASE
OPEN
button
PHASE
WRC
rotary switch
MODE
SEL/
SET/
ramp Iris
ramp
W RC
Quick Guide
7.2 Basic operating modes
Iris
50%
max Iris
max
RAMP button
off
Iris
ramp fps
fps
Iris
RAMP
com
sat
ion
pen
user
COMPENSATION
rotary switch
7.2.2 WRC mode
Set the WRC/CAM sliding switch to WRC. This mode
provides access to advanced remote control options,
which allow different ramps to be programmed with the
corresponding exposure compensation options.
IRIS ON/OFF
handwheel
172
WRC-1
fps,
,Iris
The IRIS sliding switch is used when switching on the
WRC-1 to determine whether the WRC-1 should control
the iris motor (IRIS ‘ON’) or not.
As the T-stops on the ARRIMACROS change when the
lens is focussed, the ARRIMACROS may not be used with
the LCS or the WRC-1 system.
With the WRC-1 the
- cameral speed,
- the mirror shutter angle and
- the iris of the lens
can be adjusted using the handwheel.
Programs (ramps) can be created to automatically adjust the
controlled operating functions for a pre-defined period of time.
Changes in exposure can be compensated for by automatically adjusting one or two of the other controllable
parameters.
• The camera can be started by pressing the RUN
button on the WMU-1.
• The COMPENSATION rotary switch is for defining
whether, and how, the difference in exposure resulting
from adjusting the master value is to be compensated for.
The COMPENSATION rotary switch governs the slave
values.
Quick Guide
7.3 Operation
Please read the operating instructions in chapter 5.3 and
chapter 5.5.1.5!
The WRC-1 does not have its own ON/OFF switch. It is
activated via the devices to which it is connected (e.g. the
WMU-1).
• The WRC rotary switch is used to select the master value
which is to be adjusted (camera speed, shutter angle, iris),
and determines whether the adjustment is to be made
manually using the handwheel (iris, ) , fps),
or whether it is to be time-controlled (ramp Iris, ramp ) ,
ramp fps) and started by pressing the RAMP button in
the camera run.
173
Quick Guide
factory pre-defined
user defined
7.3.1 Iris control
• Before using the iris control functions, the T-stops
engraved on the lens being used must be assigned in
the WRC-1 and the lens’ end-stops must be calibrated.
If a lens has not yet been selected and assigned to the
T-stop values in the WRC-1 (condition on delivery from
the factory, or the active iris table has been deleted
from the memory), a flashing warning ‘IRIS TBL’
appears when the WRC-1 is switched on with the IRIS
sliding switch set to the position ‘IRIS ON’.
Press the MODE button to switch to the input mode.
If a lens has already been selected and programmed,
the menu for selecting lenses or assigning T-stops can
be accessed in the WRC rotary switch position ‘IRIS’.
The so called table menu is the last submenu before
returning to the main menu.
• Press the MODE button three times in the main menu
in the WRC rotary switch position ‘IRIS’ with the
COMPENSATION rotary switch at ‘OFF’ until ‘TBL
LOAD’ is shown on the display.
174
Display:
UP
VAr P
HS 35
Std35
HS 16
User
Lens set:
ARRI Zeiss Ultra Primes
ARRI Zeiss Variable Primes
ARRI Zeiss High-speed set for 35mm film
ARRI Zeiss Standard set for 35mm film
ARRI Zeiss High-speed set for 16mm film
lenses previously defined by the user
Confirm the selection by pressing the SEL button.
Choose the required focal length using the handwheel
and confirm the selection by pressing the SET button.
Then calibrate the lens by pressing the CAL button on
the WMU-1
and set the displayed T-stop value (‘ADJ’ is shown in
the first display line) using the handwheel. Check the
T-stop on the lens.
Confirm by pressing the SET button.
Check the other available T-stops by adjusting them
with the handwheel.
• Defining iris tables for other lenses:
To avoid operational errors, turn the handwheel until
‘TBL DEL’ appears in order to delete an iris table which
may already have been set.
Press the SEL button – ‘DEL’ flashes on the display.
Press the SET button to confirm – ‘DONE’ is displayed
for a second.
Then turn the handwheel until ‘TBL EDIT’ is displayed
and confirm by pressing the SEL button.
Turn the handwheel to the left until the first T-stop given
on the iris ring of the lens being used is shown in the
second line of the display.
This must be a full T-stop from the standard T-stop range.
Then press the SEL button.
‘ADJ’ now flashes in the first line of the display.
Set the iris ring to the displayed value using the handwheel.
The T-stop value is programmed by pressing the SET button.
This is indicated in the first line by an ‘I’ next to ‘TBL’.
In case you need to delete a wrong assignment, press
the SET button again. The ‘I’ next to ‘TBL’ disappears
again.
Turn the handwheel again until the next value given on
the iris ring of the lens being used is shown on the display.
Program this and the next values as described above.
If the iris scale of the lens being used is linear, it is
sufficient to enter just two T-stop values, which must
Quick Guide
• Loading factory-defined or previously programmed lenses:
Press the SEL button and select the required lens set
using the handwheel.
175
Quick Guide
176
however be at least four T-stops apart, in order to
define the iris table.
If the iris scale is not linear, all the T-stops must be
programmed.
After programming the iris table, the T-stops on the iris
ring of the lens must be controlled by adjusting with
the handwheel and visually checking the lens.
If the created iris table should remain available for later
use, it must be stored. This also applies when an iris table
has been re-edited.
• Storing iris tables:
The handwheel must then be turned in the table menu
(TBL LOAD, TBL DEL, TBL EDIT, TBL STORE) until
‘STORE’ is displayed in the second line.
Confirm the selection by pressing the SEL button –
‘STORE’ is displayed in the first line,
and the number of the memory area is shown in the
second line (10 memory areas are available).
Select the number of the required memory area using
the handwheel and store the iris table by pressing the
SEL button.
Note down the number of the memory area together
with the programmed lens to simplify activating lenses
at a later time.
black indicator bar for main menu
The main menu is indicated by a black bar ➪ photo in
the top right corner of the display. The currently adjusted
value and the value of one of the two possible exposure
compensation options are shown in the display.
If ‘PROG’ is also shown, a time-controlled ramp function
(ramp Iris, ramp ) , ramp fps) has been selected using the
WRC rotary switch. In this case, the handwheel is without
function in the main menu.
In the three other WRC rotary switch positions (fps, ) , iris)
a parameter can be adjusted manually using the handwheel.
The display shows the adjusted value and an automatically
calculated and adjusted compensation value.
• Press the MODE button to go to the first submenu to
define the end-stops of the handwheel or the limit values
of the master value of a ramp.
Press the MODE button again to go to the next submenu.
• Press the SEL button for longer than 2 seconds in order
to activate the input mode in a submenu.
The adjustable digits flash.
These can now be set by turning the handwheel.
Press the SEL button again to activate the next digits.
Quick Guide
7.3.2 Entering values
This procedure is repeated until all the positions have
been set. The first digits are confirmed, and the decimal
positions are set to ‘0’, by pressing the SET button.
• The end-stops of the handwheel or the limit values of the
master value of a ramp are always defined in the first
submenu –
i.e. selected master value: camera speed – the limit values
for the camera speed are defined in the first submenu.
• The remaining exposure-related parameters are defined
in the following submenus, if the corresponding functions
are controlled by the WRC-1.
177
Quick Guide
178
The ramp duration is set,
the screen time is displayed when a corresponding
function is selected,
and the reading ‘CONST LIGHT’
confirms a constant exposure resulting from the values
set in the user-defined mode.
The corresponding submenus for each adjustable combination
of master values and compensations can be seen in the
following illustrations or chapter 5 of this instruction manual.
If technically executable limit values are exceeded when
defining the different parameters (e.g. settings are entered
for a high-speed camera model, then a normal production
camera is used), a warning is displayed in the main menu
‘(exceeded parameter) + RANGE’ and the READY LED
flashes green (in all submenus). The set values must then
be corrected.
If a function is not available (e.g. the camera being used
does not have an electronically adjustable mirror shutter)
the reading ‘NO + (function designation)’ is displayed.
Another compensation option or control function must be
selected.
Iris
Iris
ramp Iris
ramp Iris
ramp Iris
comp. <)
comp. user
comp. off
comp. <)
comp. user
PROG
PROG
fps
fps
PROG
fps
PROG
PROG
PROG
PROG
PROG
PROG
fps
PROG
fps
fps
PROG
fps
Quick Guide
Iris
comp. off
PROG
fps
PROG
PROG
PROG
PROG
179
Quick Guide
<)
<)
<)
ramp <)
ramp <)
ramp <)
comp. off
comp. Iris
comp. User
comp. off
comp. Iris
comp. User
PROG
PROG
fps
fps
PROG
fps
PROG
PROG
PROG
PROG
PROG
PROG
fps
PROG
fps
fps
PROG
fps
PROG
fps
PROG
PROG
PROG
PROG
180
fps
fps
fps
fps
fps
fps
comp. Iris
comp. <)
comp.Iris <) 50%
comp.max. Iris
comp.max. <)
comp.user
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
fps
Quick Guide
fps
comp. off
181
Quick Guide
ramp fps
ramp fps
ramp fps
ramp fps
ramp fps
ramp fps
ramp fps
comp.off
comp.Iris
comp.<)
comp.Iris/<)50%
comp.max. Iris
comp.max.<)
comp.user
PROG
fps
PROG
fps
PROG
fps
PROG
fps
PROG
fps
PROG
fps
PROG
PROG
fps
fps
PROG
fps
PROG
fps
PROG
PROG
fps
fps
PROG
PROG
fps
fps
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
182
Adjusting:
The term ‘adjust’ as used in this instruction
manual describes a manual alteration of one
of the adjustable parameters using the
handwheel.
Limit value: A limit value is either the left and right
handwheel end-stop, or the start and end
value of an adjusted parameter in the case
of a time-controlled ramp.
Ramp:
The term ‘ramp’ describes adjustment actions
which run automatically over a predefined
period of time after pressing the RAMP button
in the camera run, i.e. these adjustments are
not controlled using the handwheel.
Fixed value: After defining the limit values, the remaining
exposure-related parameters which do not
change when adjustments are being made
must also be defined.
Example: if the camera speed has been
selected as the parameter to be adjusted,
the shutter angle and the aperture must be
defined in the next submenus, if these are
controlled by the WRC-1.
Master value: The parameter which is to be primarily
adjusted, i.e. the iris of the lens, the mirror
shutter angle, or the camera speed.
Slave value: Adjusting the master value alters the film
exposure. This difference in exposure can
be automatically compensated for by the
WRC-1. To do this, the WRC-1 adjusts the
other parameters, e.g. altering the camera
speed can be compensated for by the iris of
the lens or by the shutter angle as required.
Glossary
8. Glossary
Screen time: The screen time is the time (in seconds)
needed for a projection at a selected
standard projection speed: 24, 25 and 30 fps
are available.
183
184
Germany ............................... Arnold & Richter Cine Technik
Türkenstraße 89
D-80799 München
phone: (089) 3809-0
fax: (089) 3809-1244
fax service: (089) 3809-1793
E-mail service:
[email protected]
USA ........................................ ARRI USA
617, Route 303
Blauvelt, New York 10913
phone: (914) 353 14 00
fax: (914) 425 12 50
E-mail: [email protected]
ARRI USA
600 North Victory Blvd.
Burbank, California 91502
phone: (818) 841 70 70
fax: (818) 848 40 28
E-mail: [email protected]
Italy ........................................ ARRI ITALIA S.R.L.
Viale Edison 318
20099 Sesto S. Giovanni (Milano)
phone: (02) 26 22 71 75
fax: (02) 242 16 92
E-mail: [email protected]
ARRI ITALIA S.R.L.
Via Placanica, 97
00040 Morena (Roma)
phone: (06) 79 89 02 02
fax: (06) 79 89 02 39
ARRI Service
9. ARRI Service
Canada .................................. ARRI Canada Ltd.
415 Horner Avenue, Unit 11
Etobicoke, Ontario
Canada M8W 4W3
phone: (416) 255 33 35
fax: (416) 255 33 99
E-mail: [email protected]
GB ........................................... ARRI (GB) Ltd.
The Movie House
1-3 Airlinks, Spitfire Way
phone: (0208) 848 88 81
fax: (0208) 561 13 12
E-mail: [email protected]
185
186
Index
A
ADJ ..................................................... 42, 45, 50, 175
adjustments ...................................................... 13, 183
under 6 fps .......................................................... 30
ANGLE RANGE ........................... 29, 56, 68, 112, 115,
118, 138, 143, 149, 167
angle symbol ................................................14, 59, 71
antenna ................................................................... 19
applications .............................................................. 10
ARRIFLEX 535A ................................................ 25, 165
ARRIMACRO .............................................. 30, 38, 172
B
battery ............................................................. 17, 171
black bar in the display ..................................... 31, 163
button
CAL .............................................. 45, 48, 166, 175
MODE .............................. 12, 25, 32, 34, 172, 177
ON ..................................................................... 27
OPEN ....................................... 12, 25, 26, 51, 172
PHASE ............................................ 12, 25, 26, 172
PROG ................................................................. 25
RAMP ..................................................... 12, 25, 31
RELEASE ............................................................. 18
SEL ........................... 12, 25, 34, 39, 172, 175, 177
SET ........................... 12, 25, 32, 34, 172, 175, 177
Index
10.Index
C
cable .............................................17, 20, 21, 24, 171
CAL button ......................................... 45, 48, 166, 175
calibration ................................................41, 168, 174
CAM mode ................................................ 12, 25, 163
camera display .........................................................25
camera program ....................................................... 25
camera-internal settings ...................................... 28, 29
capping shutter .......................................................164
CCU ........................................................................ 25
CCU socket ................................................ 21, 24, 171
charger ............................................................17, 171
CLM-1 ............................................... 17, 37, 166, 171
CLM-2 ......................................... 17, 22, 37, 166, 171
console ................................................. 17, 22, 171
console mounting ................................................. 22
CLOSE position ...................................................46, 51
compensation
angle .................................................................. 15
iris ......................................................................15
187
Index
iris / angle 50 % ................................................. 15
max. angle ..........................................................15
max. iris .............................................................. 15
off ......................................................................15
rotary switch............................ 13, 15, 25, 165, 173
user .................................................................... 15
CONST LIGHT ................ 61, 73, 87, 99, 127, 161, 178
D
dark phase ............................................................... 30
decimal positions ...................................................... 34
delay in adjusting/ramps .......................................... 30
depth of field .............................. 10, 11, 55, 66, 80, 92
display ..................................................................... 25
ADJ ................................................42, 45, 50, 175
ANGLE RANGE ...................... 29, 56, 68, 112, 115,
118, 138, 143, 149, 167
CONST LIGHT ........... 61, 73, 87, 99, 127, 161, 178
DO CAL ................................................ 41, 48, 166
DONE ..................................................... 42, 44, 50
ERR ................................................................... 168
FALSE ............................................................... 169
IRIS RANGE ........................... 29, 82, 94, 109, 115,
122, 134, 143, 155, 167
IRIS TBL ................................... 38, 40, 44, 166, 174
LENS ERROR ...............................................49, 168
NO ANGLE .................................................77, 165
188
NO FUNC ................................................... 30, 163
NO IRIS ...................................................... 37, 166
NOT PS/CCU .................................................... 165
OFF ANGLE ........................................................ 81
ONLY 25 .......................................................... 165
PR ..................................................................... 164
PROG ............................ 31, 62, 66, 71, 88, 92, 97,
128, 132, 136, 140, 147, 152, 159, 177
RA ........................................................ 62, 88, 128
SCU .................................................................. 164
SEC RANGE ...................................................... 167
SINGLE FRANE .................................................. 164
SPEED RANGE ............................................ 29, 167
STORE ........................................................ 47, 176
SU OR ESU ....................................................... 164
TBL DEL ............................................................... 39
TBL EDIT .......................................... 39, 44, 45, 175
TBL ERROR ........................................................ 169
TBL LOAD ................................................ 39, 40, 48
TBL STORE ..................................................... 39, 47
USER .................................................................. 48
DO CAL ..................................................... 41, 48, 166
DONE .........................................................42, 44, 50
dovetail adapter ............................................... 17, 171
drive gear ................................................................ 23
G
electronically adjustable mirror shutter ................ 77, 165
elements for operating ............................................... 25
end value ................................................................. 33
end-stops ................................................................. 33
calibrating ................................................... 49, 174
entering values ....................................................... 177
EPROM versions ......................................... 17, 30, 171
ERR ........................................................................168
ESU-1 .................................................................... 164
exposure compensation ............................................. 10
exposure fluctuations ................................................. 11
gear ring ............................................................23, 40
adapter ............................................................... 40
adapter ring ........................................................ 40
standard ............................................................. 40
F
factory pre-defined lenses .................................. 40, 175
fade in ................................... 58, 70, 84, 96, 124, 158
fade out .................................58, 70, 84, 96, 124, 158
FALSE .................................................................... 169
fixed values ...................................................... 33, 183
focal length selecting ................................................. 41
forward run .............................................................. 25
fps ........................................................................... 14
functions .................................................................. 12
Index
E
H
handwheel ....................................... 12, 25, 33, 34, 39
end stops ............................................................. 33
without function ................................................... 31
High-speed lenses .............................................41, 175
high-speed lenses ..................................................... 41
HMI light .................................................................. 11
I
ICU-1 .................................................................27, 29
inconsistent exposure ................................................ 11
iris ........................................................................... 14
defining end-stops / limit values ............... 53, 56, 60,
64, 68, 73, 86, 99, 127, 148, 167
memory areas ..................................................... 39
motor ........................................................ 166, 171
ON / OFF switch ........................................... 26, 37
open temporarily ................................................. 51
ring .................................................................... 45
table ................................................................... 38
189
Index
190
IRIS RANGE ................................ 29, 82, 94, 109, 115,
122, 134, 143, 155, 167
IRIS sliding switch ........................... 13, 26, 37, 38, 166
iris socket ................................................................. 23
iris table ...................................................38, 166, 174
checking ......................................... 42, 46, 50, 175
CLOSE position ..............................................46, 51
deleting an old table ............................................ 44
end-stops programming ..................................... 172
loading ......................................... 40, 48, 174, 175
programming ...................................................... 44
re-editing ............................................................ 51
standard iris scale ........................................ 46, 175
storing ........................................................ 47, 176
t-stop scale linear ................................................. 51
t-stop scale non linear .......................................... 51
wrong memory area ............................................ 49
wrong selection .................................................... 49
IRIS TBL ........................................ 38, 40, 44, 166, 174
L
LCC ......................................................................... 25
LCD ......................................................................... 27
LCS ..........................................................................17
LED
READY .......................................................... 27, 30
RF .......................................................................27
RUN ............................................................. 12, 25
lens control motor ............................................... 17, 37
LENS ERROR .................................................... 49, 168
lenses
factory-defined ............................................ 40, 175
focal length .........................................................41
High-speed ..........................................................41
pre-defined .........................................................40
selection .............................................................. 40
several lenses remote controlled ............................ 21
Standard .............................................................41
Ultra Primes .........................................................41
user-defined .......................................... 41, 44, 175
Variable Primes.................................................... 41
limit values ....................................................... 33, 183
O
main menu .............................................................163
master values ................................... 13, 173, 178, 183
memory area ................................................39, 47, 48
number ............................................................... 47
selection .............................................................. 48
mirror shutter
angle on the camera ............................................ 28
electronically adjustable ....................................... 77
mode
CAM ...........................................................12, 163
program ............................................................164
WRC ................................................................... 13
MODE button ......................... 12, 25, 32, 34, 172, 177
motor ........................................... 17, 22, 37, 166, 171
mounting .................................................................. 24
OFF ANGLE ............................................................. 81
ON button ........................................................ 27, 173
ONLY 25 ...............................................................165
OPEN button .................................. 12, 25, 26, 51, 172
operating elements .................................................... 25
N
NO ANGLE ...................................................... 77, 165
NO FUNC ........................................................ 30, 163
NO IRIS ..................................................... 23, 37, 166
non-linar phase ........................................................ 30
NORM ..................................................................... 26
NOT PS/CCU ................................................... 26, 165
Index
M
P
PHASE button ....................................... 12, 25, 26, 172
PR ..........................................................................164
pre-defined lenses ..................................................... 40
PROG .................................31, 62, 66, 71, 88, 92, 97,
128, 132, 136, 140, 147, 152, 159, 177
PROG button ............................................................ 25
program mode .......................................................164
projection speed .....................................................183
PS/CCU mode .......................................................... 25
PS/CCU sliding switch ...................................... 26, 171
R
RA ............................................................. 62, 88, 128
radio channel ........................................................... 21
countries ............................................................. 21
setting ................................................................. 21
radio connection .................................................17, 27
191
Index
192
radio link ................................................................. 17
ramp ...............................................................13, 183
angle .................................................................. 14
duration ............................................................ 178
fps ......................................................................14
iris ......................................................................14
reversing .............................. 63, 67, 72, 89, 93, 98,
129, 133, 137, 141, 147, 153, 160
time ............................ 13, 59, 71, 85, 97, 125, 159
under 6 fps ..........................................................30
RAMP button ................................................ 12, 25, 31
range of functions ....................................................... 9
READY LED ........................................................ 27, 30
flashes ................................................................ 30
light up red ..........................................................30
RELEASE button ........................................................ 18
reverse run ............................................................... 25
RF LED ..................................................................... 27
rotary switch
COMPENSATION .................... 13, 15, 25, 165, 173
WRC ...............................................13, 14, 25, 173
RS socket ..........................................................20, 171
RUN LED ............................................................12, 25
S
safety Instructions ........................................................ 7
screen time .............................. 74, 100, 131, 135, 139,
145, 151, 157, 162, 178, 183
SCU ....................................................................... 164
SEC RANGE ...........................................................167
SEL button ...................... 12, 25, 34, 39, 172, 175, 177
SET button ...................... 12, 25, 32, 34, 172, 175, 177
setting values on the camera ...................................... 28
setup ........................................................................17
shutter angle
mechanically locked ........................................... 165
setting on the camera ........................................... 28
settings ................................................................ 25
single frame unit ..................................................... 164
SINGLE FRANE ...................................................... 164
slave values .............................................. 13, 173, 183
sliding switch
IRIS ........................................... 13, 26, 37, 38, 166
PS-CCU/NORM .......................................... 26, 171
WRC/CAM .....................................12, 25, 26, 172
socket
CCU ..................................................... 21, 24, 171
IRIS ..................................................................... 23
RS ............................................................... 20, 171
speed ramps .............................................................11
SPEED RANGE ................................................. 29, 167
T
t-stop scale
linear .................................................................. 46
non-linear ........................................................... 46
t-stops ...................................................... 45, 168, 169
assigning .............................................. 38, 45, 174
checking ............................................... 42, 46, 175
CLOSE position .................................................... 46
delete an assignment .................................... 45, 175
full t-stops for checking ......................................... 42
linear scale .......................................................... 51
non linear scale ................................................... 51
not correctly assigned ........................................... 46
programming ............................. 53, 56, 60, 63, 67,
72, 86, 93, 98, 107, 114,
117, 121, 126, 133, 137,
141, 147, 153, 160, 172
standard range .......................... 38, 45, 46, 51, 175
tolerances ................................... 53, 57, 60, 63, 67,
72, 88, 93, 98, 107, 114,
117, 121, 126, 133, 137,
147, 153, 160
table ........................................................................ 38
deleting an old table ............................................ 44
menu .................................................................. 39
tbl ............................................................................ 38
TBL DEL .................................................................... 39
TBL EDIT ..................................................... 44, 45, 175
TBL ERROR .............................................................169
TBL LOAD .................................................... 39, 40, 48
TBL STORE .........................................................39, 47
telecommunications regulations .................................. 21
trouble shooting ...................................................... 163
Index
speed settings ........................................................... 25
on the camera ..................................................... 28
standard lenses ................................................. 41, 175
standard t-stop range .......................................... 45, 46
start value ................................................................ 33
STORE ............................................................. 47, 176
storing of programs and values .................................. 28
stroboscopic effects ................................................... 11
SU OR ESU ............................................................164
submenu .................................................... 32, 33, 178
table ................................................................... 39
switch
ON/OFF ..................................................... 27, 173
symbol
angle ............................................................59, 71
explanation of the symbols ..................................... 7
photo .................................................................... 7
193
Index
U
W
UC-C1 ....................................................... 17, 20, 171
UC-R1 ........................................................ 17, 21, 171
Ultra Primes ................................................ 39, 41, 175
UMC-1 ................................................17, 19, 37, 171
universal motor controller .......................................... 17
universal radio module .............................................. 17
unmounting .............................................................. 24
URM-1 .................................................17, 19, 37, 171
USER .......................................................................48
user mode ........................ 15, 58, 70, 84, 96, 124, 158
user-defined lenses ............................................ 41, 175
WAC-1 ............................................................ 17, 171
warnings .......................................................... 29, 163
WBU-2 ............................................................ 17, 171
WC-W1-S ........................................................ 24, 171
WHA-1 ............................................................ 24, 171
wireless handgrip attachment ..................................... 24
wireless main unit ..................................................... 17
wireless mode ...........................................................17
wireless operation ..................................................... 19
WMU-1 ........................................................... 17, 171
WRC mode .................................................. 13, 26, 28
WRC rotary switch ................................ 13, 14, 25, 173
WRC-1 ...................................................... 17, 24, 171
WRC/CAM sliding switch .....................12, 25, 26, 172
V
values
entering ............................................................ 177
Variable Primes .......................................... 39, 41, 175
viewfinder checking .................................................. 51
vignetting .................................. 53, 57, 60, 63, 67, 72,
88, 93, 98, 107, 114,
117, 121, 126, 133,
137, 147, 153, 160
VSU ....................................................................... 164
194
Z
Zeiss High-speed lenses ........................................... 175
Zeiss standard lenses............................................... 175
Zeiss Ultra Primes ............................................. 39, 175
Zeiss Variable Primes ........................................ 39, 175
ZMU .................................................................. 27, 29
Main
Main
Main
Menu
Menu
Menu
press MODE-key to
press MODE-key
enter table-menu
to leave menu
select
tbl
standard-lens:
LOAd
values can be checked
WRC-1: Iris Table Editing
active lens-table
active lens-table
active lens-table
deleting
editing
storing
tbl
tbL
tbL
deL
Edit
StorE
load
press SEL
MODE
to confirm
select
lens group:
UP
handwheel
VAr P,
HS 35, Std 35,
HS 16 Std 16
press SEL
press SEL
coming from
to confirm
to confirm
tbL
"tbL"
USEr
dEL
press SEL
press SEL
press SEL
press SEL to confirm
to confirm
to confirm
to confirm
tabel is deleted
select
UP
focal length:
10, 14, 16…
VAr P
16-30, 29-60,
55-105
edit
press SEL
to confirm
StorE
MODE
MODE
1-10
tbL I
F1.0 – 64,CLOSE
MODE
select number
with handwheel
I means: A value is stored in this position
USEr
1-10
handwheel
donE
select with handwheel
press SEL
1 second…
press SEL to confirm
to confirm
press SEL
"AdJ" 1
donE
to confirm
F XX
1 second…
dO
"AdJ"
Main
adjust with handwheel
Main
CAL
F XX
Menu
press SEL to confirm
Menu
press
adjust F XX
CAL-key
with handwheel
press SET
to confirm
adjusted value
must be
within the tolerance
"" display blinking
action
display
donE
decision
1 second
jump
195
technical data are subject to change without notice
© ARRI 2000
available languages:
Deutsch K 5.43660.0
English K 5.43668.0
ARNOLD & RICHTER
CINE TECHNIK
TÜRKENSTR. 89 • D-80799 MÜNCHEN • TEL. (089) 3809-0
FAX (089) 3809 - 1244 • http://www.arri.de