Transcript
OVALYN UNIVERSAL ACCESS™ UNDERCOUNTER SINK VITREOUS CHINA BARRIER FREE OVALYN UNIVERSAL ACCESS™ SINK • Made from vitreous china • Unglazed rim for under counter mount • Rear overflow • Supplied with mounting kit (047194-0070A) and template ❏ 9482.000 Nominal Dimensions: 489 x 400mm (19-1/4" x 15-3/4") Bowl sizes: 425mm (16-3/4") wide 337mm (13-1/4") front to back 140mm (5-1/2") deep 102mm (4") bowl depth 51mm (2) MIN. Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.2M for Vitreous China Fixtures • CAN/CSA B45 series • 1995 National Building Code, section 3.7 and CAN/CSA-B651-M90 and OBC 3.7. 37mm(1-7/16) DIA. HOLE TYP. 610mm (24) 51mm (2) C/L 267mm (10-1/2) 140mm (5-1/2) 400mm (15-3/4) UNDER COUNTER BASIN RIM 337mm (13-1/4) COUNTER TOP CUTOUT 45° *311mm (12-1/4) 140mm (5-1/2) 203mm (8) MIN. 864mm (34) MOUNTING CLIP (SEE DETAIL) 425mm (16-3/4) 489mm (19-1/4) SEALING COMPOUND To Be Specified: ❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Fawn Beige ❏ Black ❏ Faucet*: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap: FINISHED WALL 70mm (2-3/4) DRAWING FOR DIMENSIONAL PURPOSES ONLY. IT IS NOT AN EXACT REPRESENTATION. 686mm (27) MIN. 152mm (6) MAX. BARRIER FREE CLEARANCE COUNTERTOP (BY OTHERS) 16mm +3mm(1/8) (5/8) -2mm(1/16) 229mm (9) MIN. DETAIL OF MOUNTING CLIP (KIT No.047194-0070A) 92mm (3-5/8) BRASS INSERT 19mm (3/4) MIN. LAVA *262mm (10-1/2) 203mm (8) SUPPLIES AS REQ'D 1-1/4 O.D. TAILPIECE 1-1/4 O.D. WASTE CLIP MACH. SCREW REFER TO INSTRUCTIONS PROVIDED WITH KIT FOR ADDITIONAL INFORMATION * See faucet section for additional models available For Universal Design Options, top of counter may be mounted at 813mm (32") minimum from finished floor to meet ADA and ANSI A117.1 requirements. A 838mm (33") minimum mounting height is required for Ontario. Check local codes for heights and faucet handles requirements. MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES CHECK LOCAL CODES. Countertop 864mm (34") from finished floor. Lavatory installed 51mm (2") MIN. from front edge of countertop. Countertop thickness to be 25mm (1") maximum. © 2008 AS America Inc. NOTES: DIMENSIONS SHOWN FOR LOCATION OF SUPPLIED AND “P" TRAP ARE *SUGGESTED. ▼ UNDERCOUNTER MOUNTING KIT SUPPLIED WITH BASIN. FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. USE ENCLOSED TEMPLATE FOR COUNTERTOP CUTOUT SEALING COMPOUND SUPPLIED BY OTHERS. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. J55 Revised 2/08