Download American Standard High Hamilton Elongated Space-saving One-Piece Toilet 2096.333 User's Manual

HIGH HAMILTON™ELONGATED
SPACE-SAVING ONE-PIECE TOILET
VITREOUS CHINA
BARRIER FREE
HIGH HAMILTON™ ELONGATED SPACESAVING ONE-PIECE TOILET
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• One-piece toilet features a higher (427mm
16-13/16”) bowl for added comfort
• Elongated siphon action bowl and tank
with unique space-saving feature
• Fits into the same space as a conventional
round front toilet
• Color-matched trip lever
• Internal trapway area fully glazed
• Includes color-matched Rise and Shine™
plastic seat and cover (#5324.019) with
easy-to-clean lift-off hinge system
• 2 bolt caps
• 100% factory flush tested
❏
❏
2096.016
2096.333
• Right-hand trip lever
FINISHED WALL
Nominal Dimensions:
692 x 457 x 699mm
(27-1/4" x 18" x 27-1/2")
692mm
(27-1/4)
184mm
(7-1/4)
13mm
(1/2)
Fixture only, supply by others
481mm
(18-15/16)
C/L
Compliance Certifications Meets or Exceeds the Following Specifications:
• ASME A112.19.2M (and 19.6M) for Vitreous
China Fixtures - includes Flush Performance,
Ball Pass Diameter, Trap Seal Depth and
all Dimensions
427mm
(16-13/16)
FINISHED
FLOOR
16mm
(5/8)
164mm
(6-7/16)
To Be Specified
Color:
❏
Supply with stop:
MEETS THE AMERICAN DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
● When installed, top of seat meets minimum requirement of
432 to 483mm (17" to 19") from the finished floor.
699mm
(27-1/2)
SUPPLY AS
REQUIRED
76mm
(3)
❏
457mm
(18)
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
305mm
(12)
*152mm
(6)
*152mm
(6)
243mm
(9-9/16)
229mm
(9)
368mm
(14-1/2)
NOTE: Roughing-in information shown on reverse side of page
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12")
FROM FINISHED WALL TO C/L OF OUTLET.
DIMENSIONS SHOWN FOR LOCATION OF SUPPLY ARE SUGGESTED.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance
established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for use
of superseded or voided pages.
*
10
© 2004 American Standard Inc.
Revised 10/04
HIGH HAMILTON™ELONGATED
SPACE-SAVING ONE-PIECE TOILET
VITREOUS CHINA
BARRIER FREE
2096.333 RIGHT HAND HOLE TRIP LEVER
FINISHED WALL
692mm
(27-1/4)
184mm
(7-1/4)
13mm
(1/2)
457mm
(18)
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
481mm
(18-15/16)
C/L
427mm
(16-13/16)
699mm
(27-1/2)
SUPPLY AS
REQUIRED
FINISHED
FLOOR
76mm
(3)
16mm
(5/8)
164mm
(6-7/16)
*152mm
(6)
*152mm
(6)
243mm
(9-9/16)
229mm
(9)
305mm
(12)
368mm
(14-1/2)
MEETS THE AMERICAN DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
● When installed, top of seat meets minimum requirement of
432 to 483mm (17" to 19") from the finished floor.
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12")
FROM FINISHED WALL TO C/L OF OUTLET.
DIMENSIONS SHOWN FOR LOCATION OF SUPPLY ARE SUGGESTED.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance
established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for use
of superseded or voided pages.
*
11
© 2004 American Standard Inc.