Download Allied Telesis AT-MC101XL User's Manual
Transcript
4. For the AT-PC232/POE or the AT-PC2002/POE, install the AC power cord and secure it with the retaining clip provided with the media converter as shown in Figure 5, “Securing AC Power Cord with the Retaining Clip”. 4. DINRAIL Mounting Bracket Installation Guide For the AT-PC232/POE or the AT-PC2002/POE, install the AC power cord and secure it with the retaining clip provided with the media converter as shown in Figure 5, “Securing AC Power Cord with the Retaining Clip”. Overview Overview SPEE (Mbp D DUPL s) EX MODE 10 100 HALF FULL 1 This guide provides assembly instructions for assembling and mounting a DINRAIL mounting bracket with one of the following Allied Telesis products: AUTO NEG OFF ON SPEE (Mbp D DUPL s) EX MODE 10 100 • AT-MC101XL, AT-MC102XL, AT-MC103XL and LH, AT-MC104XL, and AT-MC605 Media Converters • AT-MC1004, AT-MC1008/GB, AT-MC1008/SP, and AT-GS2002/SP Media Converters • AT-PC232/POE and AT-PC2002/POE Media Converters • AT-FS201, AT-FS202, AT-FS232, AT-FS232/1, and AT-FS232/2 Media Converters 2 2 1 3 4 2 POR 2 T 100-2 40VA C~ 1382 HALF FULL 1 This guide provides assembly instructions for assembling and mounting a DINRAIL mounting bracket with one of the following Allied Telesis products: AUTO NEG OFF ON • AT-MC101XL, AT-MC102XL, AT-MC103XL and LH, AT-MC104XL, and AT-MC605 Media Converters • AT-MC1004, AT-MC1008/GB, AT-MC1008/SP, and AT-GS2002/SP Media Converters • AT-PC232/POE and AT-PC2002/POE Media Converters • AT-FS201, AT-FS202, AT-FS232, AT-FS232/1, and AT-FS232/2 Media Converters 2 2 1 3 4 2 POR 2 T 100-2 40VA C~ 1382 Verifying the Package Contents Verifying the Package Contents Figure 5 - Securing AC Power Cord with the Retaining Clip 5. Install the mounting bracket on the DINRAIL. As shown in Figure 6, “Mounting the Bracket on the DINRAIL”, the bracket may be oriented either with the bracket screw above or below the DINRAIL.. Slide the hook towards the DINRAIL until it is snug and then tighten the bracket screw. Make sure that these components are included in your package: • • • • 10 DINRAIL mounting brackets 20 M3 mounting screws 10 tie-wraps This installation guide If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. Figure 5 - Securing AC Power Cord with the Retaining Clip 5. Install the mounting bracket on the DINRAIL. As shown in Figure 6, “Mounting the Bracket on the DINRAIL”, the bracket may be oriented either with the bracket screw above or below the DINRAIL.. Slide the hook towards the DINRAIL until it is snug and then tighten the bracket screw. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. 1. Find your media converter model in Figure 1, 2 or 3 on pages 2 and 3 as listed here: Find your media converter model in Figure 1, 2 or 3 on pages 2 and 3 as listed here: Figure 1 AT-MC101XL AT-MC102XL AT-MC103XL and LH AT-MC104XL AT-MC1004 AT-MC1008/GB AT-MC1008/SP AT-GS2002/SP AT-FS232 AT-FS201 AT-FS202 • • • • • • • • • • • 1519 AT-MC101XL AT-MC102XL AT-MC103XL and LH AT-MC104XL AT-MC1004 AT-MC1008/GB AT-MC1008/SP AT-GS2002/SP AT-FS232 AT-FS201 AT-FS202 Figure 2 Figure 6 - Mounting the Bracket on the DINRAIL • AT-MC605 • AT-MC605 Figure 3 Figure 3 • AT-PC232/POE • AT-PC2002/POE • AT-PC232/POE • AT-PC2002/POE Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Page 4 10 DINRAIL mounting brackets 20 M3 mounting screws 10 tie-wraps This installation guide 1. Figure 2 PN 613-001150 Rev B • • • • Assembling a DINRAIL Bracket and Meda Converter • • • • • • • • • • • Figure 6 - Mounting the Bracket on the DINRAIL Make sure that these components are included in your package: Assembling a DINRAIL Bracket and Meda Converter Figure 1 1519 DINRAIL Mounting Bracket Installation Guide Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. PN 613-001150 Rev B Page 1 PN 613-001150 Rev B Page 4 PN 613-001150 Rev B Page 1 2. 2. X -F e s a B 0 0 1 X T 2 B X R IN G G IN X R G G ID ID R R B E D O IM LT U M 1 2 E D O IM LT U M 1 3 2 S F TA X T L T O R /C O FD P X -F e s a B 0 0 1 3 2 S F TA L T O R /C O FD P K LN C E E L M E E L M E 8 L U .3 U .3 2 2 0 0 /8 /8 .3 .3 2 2 L 0 0 8 M E S D LT O M IE IE M E S D LT O M R R E T E T R R E 1 T S UC AS OD CL PR D LE V V 1 T S UC AS OD CL PR D LE N N O O C U A M 2 O T X X I- I- D D M M I/ I/ D D M 2 O T T R O P U A T R O P / X e-T -T WR as e P UTO B as A EG 10 00B N 0M 1 10 K LN / FD L O C K LN / FD L O C / X e-T -T WR as e P UTO B as A EG 10 00B N 0M 1 10 Slide your media converter into the bracket and align the its mounting holes with those on the DINRAIL bracket as shown in the figure for your media converter. Secure the media converter to the bracket using the two M3 mounting screws provided. K LN Slide your media converter into the bracket and align the its mounting holes with those on the DINRAIL bracket as shown in the figure for your media converter. Secure the media converter to the bracket using the two M3 mounting screws provided. K LIN T X X R R X X e-F as 0B 10 X T E D O M K N L T C A I LT U /M T E D O M K N L T C A I LT U /M E D O M E D O M E D O M X e-F as 0B 10 E L G IN S E L G IN S L X X E D O M E L G IN S E L G IN S L X 4 0 1 C M TA T 4 0 1 C M TA T TS T TS /L M N O T 1 UC SS OD CLA PR ER LAS K LIN /L M N O T 1 UC SS OD CLA PR ER LAS X X X I LT U 4 T C A /L M N O R W P /L M R W P N O R E T R E V N O C 4 T C A R E T R E V N O C IA D E M X e-F as 0B INK L 10 E D O M IA D E M X e-F as 0B INK L 10 E D O M T M E N R E H T E I LT U T M E N R E H T E R T S A F R T S A F R E IB F R E IB F 1522 1522 Figure 3 - Attaching the DINRAIL Bracket to an AT-PC232/POE or AT-PC2002/POE Media Converter 1517 Figure 1 - Attaching the DINRAIL Bracket to an AT-MC10x, AT-MC1004, AT-MC1008/GB, AT-MC1008/SP, AT-GS2002/SP, AT-FS232, AT-FS201, or AT-FS202 Media Converter 3. For all of the media converters except the AT-PC232/ POE and the AT-PC2002/POE, install the DC power cord and secure it to the bracket with a tie-wrap, as shown in Figure 4, “Securing the DC power cord to the DINRAIL bracket”. Figure 3 - Attaching the DINRAIL Bracket to an AT-PC232/POE or AT-PC2002/POE Media Converter 1517 3. Figure 1 - Attaching the DINRAIL Bracket to an AT-MC10x, AT-MC1004, AT-MC1008/GB, AT-MC1008/SP, AT-GS2002/SP, AT-FS232, AT-FS201, or AT-FS202 Media Converter For all of the media converters except the AT-PC232/ POE and the AT-PC2002/POE, install the DC power cord and secure it to the bracket with a tie-wrap, as shown in Figure 4, “Securing the DC power cord to the DINRAIL bracket”. R PW T/ e- X as T B e10 as T 0B C 10 K/A LN 0M 10 T/ e- X as T B e10 as T 0B C 10 K/A LN 0M 10 R PW V FA B B H O H O E N P T E N R P T E N R E H T 9d E B IT M LI D E TE RA 9d E H T E IT M LI D E TE RA D N E T TL IN X E OV PR L S D V B D N E T TL IN FIG 6d N O IT C LIM L S NO D ST FA FIG 6d N O IT C LIM L S NO D ST X E OV PR L S D V BR SC 5 60 C M TA V BR SC 5 60 C M TA E N V D S L 12VD C C 1523 1521 1521 Figure 2 - Attaching the DINRAIL Bracket to an AT-MC605 Media Converter PN 613-001150 Rev B 12VD K N LI E AT R E BR LIN SC OV PR K N LI E AT R E BR LIN SC OV PR D L V S 1523 Page 2 Figure 4 - Securing the DC power cord to the DINRAIL bracket PN 613-001150 Rev B Page 3 Figure 2 - Attaching the DINRAIL Bracket to an AT-MC605 Media Converter PN 613-001150 Rev B Page 2 Figure 4 - Securing the DC power cord to the DINRAIL bracket PN 613-001150 Rev B Page 3