Download Finisar XFP 1310nm 10km SMF
Transcript
Finisar Productt Specificaation 10Gb b/s 10km m Datacom m XFP O Optical Transceivver FTLX1413D3B BCL PRO ODUCT FEA ATURES • Supports 8.5Gb/s to 10.5Gb/s 1 bit rates* • Power disssipation <1..5W • Commerccial temperatture range: -5°C to 75 5°C • RoHS-6 Compliant C (llead-free) • Hot-plugg gable XFP fo ootprint • Single power supply: 3.3V • Maximum m link length h of 10km APPL LICATIONS S • Uncooled d 1310nm DF FB laser • 100GBASE-LR R/LW 10G E Ethernet • Duplex LC connectorr • • No Refereence Clock required r 12200-SM-LL--L 10G Fibree Channel annd 800-SM-L LC-L 8G Fibbre Channel • Built-in digital d diagno ostic functions • 100G CPRI 413D3BCL Small Form m Factor 10G Gb/s (XFP) trransceivers aare compliannt Finisar’s FTLX14 with the current XFP X Multi-S Source Agreeement (MSA A) Specificaation1. Theyy comply witth Gigabit Ethern net 10GBAS SE-LR/LW per p IEEE 8002.3ae, 10G Fibre Channnel 1200-SM M10-G LL-L L, 8G Fibre Channel C 800-SM-LC-L, and 10G CP PRI. This traansceiver cann also suppoort OTN N/FEC protoccols OTU1ee and OTU2e upon requuest.Digital diagnostics functions arre availaable via a 2-wire 2 seriall interface, as a specifiedd in the XFP P MSA. If S SONET/SDH H comp pliance is required, r pleease see Fiinisar Part Number FT TLX1413M33BCL. Thhe transcceiver is Ro oHS compliiant and leaad free per Directive 22002/95/EC3, and Finisaar Application Notee AN-20384. PRO ODUCT SEL LECTION FTLX14 F 413D3B BCL * Please contact Finisar F for higher h data raate support © Finiisar Corporatio on March 2013 3 Rev C1 Pagee 1 FTLX1413D3BCL Datacom XFP Product Specification – March 2013 I. Finisar Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 29 30 CML-O CML-O CML-I CML-I GND GND TDTD+ GND Name/Description Module Ground Optional –5.2 Power Supply – Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply – Not required Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply – Not required Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply – Not required Module Ground Reference Clock non-inverted input, AC coupled on the host board – Not required Reference Clock inverted input, AC coupled on the host board – Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 3 3 1 1 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k – 10kohms on host board to a voltage between 3.15V and 3.6V. 3. A Reference Clock input is not required by the FTLX1413D3BCL. If present, it will be ignored. © Finisar Corporation March 2013 Rev C1 Page 2 Finisar FTLX X1413D3BCL Datacom D XFP Product P Speciffication – Marcch 2013 Diagram D of Ho ost Board Con nnector Block Pin Numbers and Name II. Absolute Maximum Ratings Parameeter Maxim mum Supply Voltage V Storag ge Temperaturee Case Operating O Tem mperature © Finiisar Corporatio on March 2013 3 Symbol Vcc3 TS TOP Min -0.5 -40 -5 Rev C1 Typ Max 4.0 85 75 Unit V °C °C Reff. Pagee 3 Finisar FTLX1413D3BCL Datacom XFP Product Specification – March 2013 III. Electrical Characteristics (TOP = -5 to 75 °C, VCC3 = 3.13 to 3.45 Volts) Parameter Supply Voltage Supply Current Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc3 Icc3 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 3.13 Typ Max 3.45 600 1.5 Unit V mA W Ω mV V V us 2 820 Vcc GND+ 0.8 10 mV ps ps V V 4 5 5 6 6 7 100 120 2.0 GND 340 Vcc – 0.5 GND 650 850 38 38 VccHOST GND+0.5 See Note 7 below Ref. 1 3 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 – 80 % 6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1. © Finisar Corporation March 2013 Rev C1 Page 4 Finisar FTLX1413D3BCL Datacom XFP Product Specification – March 2013 IV. Optical Characteristics (TOP = -5 to 75 °C, VCC3 = 3.13 to 3.45 Volts) Parameter Transmitter Optical Modulation Amplitude (OMA) Maximum Launch Power Optical Wavelength Sidemode Supression ratio Optical Extinction Ratio Transmitter and Dispersion Penalty Average Launch power of OFF transmitter Tx Jitter Relative Intensity Noise Receiver Receiver Sensitivity (OMA) @ 10.5Gb/s Stressed Receiver Sensitivity (OMA) @ 10.5Gb/s Maximum Input Power Optical Center Wavelength Receiver Reflectance LOS De-Assert LOS Assert LOS Hysteresis Symbol Min POMA PMAX λ SSRmin ER TDP POFF Typ Max Unit -4.8 0 dBm -6.0 1260 30 3.5 0.5 1355 dBm nm dB dB dB dBm 3.2 -30 Txj RIN Per 802.3ae requirements -130 Ref. dB/Hz RSENS1 -12.6 dBm 1 RSENS2 -10.3 dBm 2 PMAX λC Rrx LOSD LOSA +0.5 1260 -32 0.5 1600 -12 -18 dBm nm dB dBm dBm dB Notes: 1. Measured with worst ER; BER<10-12; 231 – 1 PRBS. 2. Per IEEE 802.3ae. Equivalent to –13.3 dBm average power at Infinite ER. 8.5Gb/s Fibre-Channel: To operate the FTLX1413D3BCL at 8.5Gb/s Fibre-Channel, the EEPROM-Table 0, Byte 117, Bit 0 must be set as follows; . • EEPROM Byte 117, Bit 0, value “1” for 8GFC: • EEPROM Byte 117, Bit 0 value “0” for 10Gb/s rates: o (It is also possible to bypass the CDRs with, Byte 111, Bit 0.) By default, a power cycling the transceiver will return the transceiver to normal 10Gb/s operation with the CDRs active. © Finisar Corporation March 2013 Rev C1 Page 5 Finisar FTLX1413D3BCL Datacom XFP Product Specification – March 2013 V. General Specifications Parameter Bit Rate Bit Error Ratio Max. Supported Link Length Symbol BR BER LMAX Min 8.5 Typ Max 10.5 10-12 10 Units Gb/s km Ref. 1 2 1 Notes: 1. 10GBASE-LR/LW, 1200-SM-LL-L, 800-SM-LC-L, and 10G CPRI 2. Tested with a 231 – 1 PRBS VI. Environmental Specifications Finisar FTLX1413D3BCL transceivers have a commercial operating case temperature range of -5°C to +75°C. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -5 -40 Typ Max 75 85 Units °C °C Ref. Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TÜV R72101686 Electrical Safety Electrical Safety TÜV EN 60825-1: 2007, EN60825-2:2004+A1 IEC 60825-1: 2007 (2nd Edition) IEC 60825-2: 2010 (3rd Edition) EN 60950:2006+A11 CLASS 3862.07 CLASS 3862.87 2283290 UL/CSA Certificate Number 9210176-77 R72101686 Copies of the referenced certificates are available at Finisar Corporation upon request. © Finisar Corporation March 2013 Rev C1 Page 6 FTLX1413D3BCL Datacom XFP Product Specification – March 2013 Finisar VIII. Digital Diagnostic Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: • • • • • Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information including memory map definitions, please see Finisar Application Note AN-2035 “Digital Diagnostic Monitoring Interface for XFP Optical Transceivers”, or the XFP MSA Specification1. © Finisar Corporation March 2013 Rev C1 Page 7 FTLX1413D3BCL Datacom XFP Product Specification – March 2013 IX. Finisar Mechanical Specifications Finisar’s XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA). 77.95 22.15 18.35 13.30 8.50 LATCHED 16.00 UNLATCHED 20.85 39.00 R1.00 XFP Transceiver (dimensions are in mm) © Finisar Corporation March 2013 Rev C1 Page 8 FTLX X1413D3BCL Datacom D XFP Product P Speciffication – Marcch 2013 X. Finisar PCB Layou ut and Bezeel Recommeendations XFP Host Bo oard Mechaniical Layout (d dimensions aree in mm) © Finiisar Corporatio on March 2013 3 Rev C1 Pagee 9 FTLX X1413D3BCL Datacom D XFP Product P Speciffication – Marcch 2013 Finisar XF FP Detail Host Board Mech hanical Layoutt (dimensions are in mm) XFP Recom mmended Bezzel Design (dim mensions are iin mm) © Finiisar Corporatio on March 2013 3 Rev C1 Page 110 FTLX1413D3BCL Datacom XFP Product Specification – March 2013 Finisar XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 – August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP Optical Transceivers” – Finisar Corporation, December 2003 3. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. January 27, 2003. 4. “Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers”, Finisar Corporation, January 21, 2005. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation March 2013 Rev C1 Page 11