1
Download Biostar GF7050V-M7 SE motherboard
Transcript
GF7050V-M7 SE Setup Manual FCC Information and Copyright This equipment has been tes ted and found to comply with the limits of a Class B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protec tion against harmful interference in a residential installation. T his equipment generates , uses , and c an radiate radio frequency energy and, if not ins talled and used in accordance with the instructions , may cause harmful interference to radio communications . There is no guarantee that interference will not occur in a particular ins tallation. The vendor makes no representations or warranties with respec t to the contents here and s pecially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make c hanges to the c ontents here without obligation to notify any party beforehand. D uplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be c hanged without notice and we will not be res ponsible for any mis takes found in this user’s manual. All the brand and produc t names are trademarks of their respec tive companies . Table of Contents Chapter 1: Introduction.....................................................1 1.1 Before You Start................................................................... 1 1.2 Package Checklist................................................................ 1 1.3 Motherboard Features.......................................................... 2 1.4 Rear Panel Connectors.......................................................... 3 1.5 Motherboard Layout ............................................................ 4 Chapter 2: Hardware Installation........................................5 2.1 Installing Central Processing Unit (CPU) ................................ 5 2.2 FAN Headers........................................................................ 7 2.3 Installing System Memory...................................................... 8 2.4 Connectors and Slots ............................................................10 Chapter 3: Headers & Jumpers Setup................................. 12 3.1 How to Setup Jumpers..........................................................12 3.2 Detail Settings.....................................................................12 Chapter 4: RAID Functions ............................................... 19 4.1 Operation System................................................................19 4.2 Raid Arrays.........................................................................19 4.3 How RAID Works.................................................................19 Chapter 5: Useful Help ..................................................... 22 5.1 Driver Installation Note .......................................................22 5.2 Software .............................................................................23 5.3 Extra Information................................................................27 5.4 AMI BIOS Beep Code............................................................29 5.5 Troubleshooting...................................................................30 A ppendencies: SPEC In Other Language............................. 32 German................................................................................................32 France..................................................................................................34 Italian..................................................................................................36 Spanish ................................................................................................38 Portuguese...........................................................................................40 Polish...................................................................................................42 Russian ................................................................................................44 Arabic..................................................................................................46 Japanese ..............................................................................................48 GF7050V-M7 SE CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU ST ART Thank you for choosing our product. Be fore you start installing the mothe rboard, please make sure you follow the instructions be low: Prepare a dry and stable work ing environment with sufficie nt lighting. Always disconne ct the compute r from powe r outle t be fore ope ration. Before you take the mothe rboard out from anti-static bag, ground yourse lf prope rly by touching any safe ly grounde d appliance, or use grounded wrist strap to remove the static charge. Avoid touching the compone nts on mothe rboard or the rear side of the board unless ne cessary. Hold the board on the edge , do not try to be nd or flex the board. 1.2 Do not leave any unfastene d small parts inside the case afte r installation. Loose parts will cause short circuits which may damage the equipment. Keep the compute r from dange rous a rea, such as hea t source , humid air and wate r. PACKAGE CHECKLIST HDD Cable X 1 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Se tup Drive r C D X 1 (full ve rsion manual files inside ) Se rial ATA Cable X 1 FDD Cable X 1 (optional) Se rial ATA Powe r Cable X 1 (optional) USB 2.0 Cable X1 (optional) S/PDIF out Cable X 1 (optional) Note: The package contents may differ by area or your motherboard version. 1 Motherboard Manual 1.3 MOT HERBOARD FEAT URES SPEC LGA 775 CPU Supports Hyper-Threading / Execute Disable Bit / Intel Core2Duo / Core2Quad / Celeron 4xx / Enhanced Intel SpeedStep® / Intel Architecture-64 Pentium D / Pentium 4 processor / Extended Memory 64 Technology / Virtualization Supports 45nm CPU Technology FSB 1333 MHz Chipset GeForce 7050/nForce 610i Graphics GeForce 7050/nForce 610i Max Shared Video Memory is 512MB(under OS) ITE 8718F Environment Control initiatives, Provides the most commonly used legacy H/W Monitor Super I/O functionality. Fan Speed Controller Low Pin Count Interface ITE's "Smart Guardian" function Super I/O DIMM Slots x 2 Main Memory Each DIMM supports 256MB/512MB/1GB/ 2GB DDR2 Single Channel Mode DDR2 memory module Registered DIMM and ECC DIMM is not supported Max Memory Capacity 4GB Supports DDR2 533 / 667 / 800 IDE Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode Integrated IDE Controller supports PIO Mode 0~4, Data transfer rates up to 3.0 Gb/s. SATA Integrated Serial ATA Controller SATA Version 2.0 specification compliant. RAID 0 / 1 / 0+1 support LAN Sound Codec 10 / 100 Mb/s auto negotiation Realtek 8201CL PHY Half / Full duplex capability 5.1 channels audio out ALC662 High-Definition Audio support PCI Express x16 slot x1 Supports PCI-E x16 expansion cards PCI Express x1 slot x1 Supports PCI-E x1 expansion cards PCI slot x2 Supports PCI expansion cards On Board Floppy connector x1 Each connector supports 2 Floppy drives Connector IDE Connector x1 Each connector supports 2 IDE device Slots 2 Printer Port Connector x1 Each connector supports 1 Printer port SATA Connector x4 Each connector supports 1 SATA devices GF7050V-M7 SE SPEC Back Panel I/O Front Panel Connector x1 Supports front panel facilities Front Audio Connector x1 Supports front panel audio function CD-in Connector x1 Supports CD audio-in function S/PDIF out connector x1 Supports digital audio out function CPU Fan header x1 CPU Fan power supply (with Smart Fan function) System Fan header x1 System Fan Power supply Clear CMOS header x1 Restore CMOS data to factory default USB connector x2 Each connector supports 2 front panel USB ports Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/2 Keyboard PS/2 Mouse x1 Connects to PS/2 Mouse Serial Port x1 Provide RS-232 Serial connection VGA port x1 Connects to monitor. LAN port x1 Connects to RJ-45 ethernet cable USB Port x4 Connects to USB devices Audio Jack x3 Provide Audio-In/Out and microphone connection Board Size 185 (W) x 244 (L) mm Micro ATX form Factor Biostar Reserves the right to add or remove support OS Support Windows XP / VISTA 1.4 for any OS with or without notice. REAR PANEL CONNECT ORS PS/2 M ouse LAN Lin e In/ Surr ound Line Out Mic In 1/ Bas s/ Center PS/2 Key board C OM 1 VGA1 USBX2 USBX2 Since the audio c hip s upports High Definiti on Audio Specific ation, the func tion of eac h audi o jack c an be defined by software. T he input / output function of each audio jac k listed above represents the default s etti ng. However, when c onnecti ng exter nal microphone to the audio port, pleas e us e the Line In (Blue) and Mic In (Pi nk) audio j ac k. 3 Motherboard Manual 1.5 MOT HERBOARD LAYOUT JKB MS1 JCFAN1 JKB_PWR1 COM1 JCOM1 LGA775 JATXPWR3 JATXPWR2 CPU1 DIMMA2 DIMMA1 JVGA1 JUSB1 JUSB_PWR1 JUSBLAN1 JAUDIO1 IDE1 GeForce 7050/ nForce 610i LAN BIOS JCDIN1 PEX1_1 PEX16_1 SATA4 SATA3 BAT1 SATA2 PCI1 SATA1 Super I/O JSPDIF_OUT1 JCMOS1 PCI2 JAUDIOF1 Codec JPRNT1 JUSB_PWR2 FDD1 Not e: ■ repre sents the 1st pin. 4 JUSB2 JUSB3 JPANEL1 JSFAN1 GF7050V-M7 SE CHAPTER 2: HARDWARE INSTALLATION 2.1 INST ALLING CENT RAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin-Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle. 5 Motherboard Manual Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the JCFAN1. This completes the installation. 6 GF7050V-M7 SE 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. JCFAN1: CPU Fan Heade r 4 1 Assignment Ground +12V FAN RPM rate sense Smart Fan Control Pin 1 2 3 4 JSFAN1: System Fan He ader Pin 1 2 3 1 Assignment Ground +12V FAN RPM rate sense 3 Note: The JCFAN1 and JSFAN1 s upport 4-pin and 3-pin head connec tor. When connecting with wires onto c onnectors, please note that the red wire is the positi ve and s houl d be connected to pi n#2, and the bl ac k wire is Ground and s hould be c onnected to GND. 7 Motherboard Manual 2.3 INST ALLING SYST EM MEMORY DIMMA1 DIMMA2 A. Memory Modules 1. 8 Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. GF7050V-M7 SE 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. B. Memory Capacity DIMM Socket Location DIMMA1 256MB/512MB/1024MB/2048MB DIMMA2 256MB/512MB/1024MB/2048MB DDR2 Module Total Memory Size Max is 4GB. 9 Motherboard Manual 2.4 CONNECT ORS AND SLOT S FDD1: Floppy Disk Conne ctor The motherboard prov ides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the prov ided f loppy drive ribbon cables. 2 34 1 33 IDE1: Hard Disk Conne ctor The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 f unctionality. The IDE connector can connect a master and a slave drive, so y ou can connect up to two hard disk driv es. 40 2 10 39 1 GF7050V-M7 SE PEX16_1: PCI-Express x16 Slot - PCI-Express 1.0a compliant. - Maximum theoretical realized bandwidth of 2GB/s simultaneously per direction, f or an aggregate of 4GB/s totally. - x8 Speed by Chipset Specif ication. PEX1_1: PCI-Expre ss x1 Slot - PCI-Express 1.0a compliant. Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. - 2X bandwidth ov er the traditional PCI architecture. PEX1 _1 PEX16_1 PCI1~PCI2: Pe riphe ral Component Interconne ct Slots The motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 11 Motherboard Manual CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW T O SET UP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DET AIL SETT INGS JPANEL1: Front Panel Heade r This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connections. It allows user to connect the PC case’s f ront panel switch f unctions. PWR_LED ON/OFF ++ - 9 1 + SPK Pin 1 2 3 4 5 6 7 8 12 Assignment +5V N/A N/A Speaker HDD LED (+) HDD LED (-) Ground Reset control Functio n Speaker Connector Hard drive LED Reset button Pin 9 10 11 12 13 14 15 16 16 8 RST HLED Assignment N/A N/A N/A Power LED (+) Power LED (+) Power LED (-) Power button Ground Functio n N/A N/A Power LED Power-on button GF7050V-M7 SE JATXPWR1: ATX Powe r Source Conne ctor This connector allows user to connect 24-pin power connector on the ATX power supply. 12 24 1 13 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage +5V +12V +12V +3.3V +3.3V -12V Ground PS_ON Ground Ground Ground -5V +5V +5V +5V Ground JATXPWR2: ATX Powe r Source Conne ctor By connecting this connector, it will provide +12V to CPU power circuit. 3 2 4 1 Pin 1 2 3 4 Assignment +12V +12V Ground Ground Note: Befor e power on the s ystem, pleas e make sure that both J ATXPWR1 and JAT XPWR2 connectors have been pl ugged-in. 13 Motherboard Manual JUSB2/JUSB3: Heade rs for USB 2.0 Ports at Front Panel This motherboard prov ides 2 USB 2.0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB dev ices, like USB card reader. JUSB2 JUSB3 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC SATA1~SATA4: Se rial ATA Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA interf ace, it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s. SATA1 SATA 2 SATA3 S ATA4 1 4 7 14 Pin Assignment 1 Ground 2 T X+ 3 T X- 4 Ground 5 RX- 6 RX+ 7 Ground GF7050V-M7 SE JSPDIF_O UT1: Digital Audio out Conne ctors This connector allows user to connect the PCI bracket SPDIF output header. Pin 1 2 3 3 Assignment +5V SPDIF_OUT 1 Ground 1 JAUDIO F1: Front Panel Audio Heade r This header allows user to connect the front audio output cable with the PC f ront panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense 15 Motherboard Manual JCDIN1: CD-RO M Audio-in Connector This connector allows user to connect the audio source f rom the variaty dev ices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.. Pin 1 1 2 3 4 4 Assignment Left Channel Input Ground Ground Right Channel Input JCMO S1: Cle ar CMOS Heade r By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting and the CMOS data, please carefully f ollow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (Default). 1 1 3 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Proce dures: 16 1. 2. 3. 4. 5. Remov e AC power line. Set the jumper to “Pin 2-3 close”. Wait f or f ive seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. 6. Reset your desired password or clear the CMOS data. GF7050V-M7 SE JUSB_PWR1/JUSB_PWR2: Powe r Source Heade rs for USB Ports Pin 1-2 Close: JUSB_PWR1: +5V for USB ports at JUSB1/JUSBLAN1. JUSB_PWR2: +5V for USB ports at f ront panel (JUSB2/JUSB3). Pin 2-3 Close: JUSB_PWR1: +5V STB for USB ports at JUSB1/JUSBLAN1. JUSB_PWR2: +5V STB for USB ports at f ront panel (JUSB2/JUSB3). JUSB_PWR1 3 3 1 Pin 1-2 close 1 JUSB_PWR2 3 1 3 1 Pin 2-3 close JKB_PWR1: Power Source Heade r for PS/2 Ke yboard and Mouse 3 1 3 1 Pin 1-2 close +5V for PS/2 keyboard and mouse. 3 1 Pin 2-3 close +5V STB for PS/2 keyboard and mouse. 17 Motherboard Manual JPRNT1: Printe r Port Connector This header allows you to connector printer on the PC. 2 1 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 18 Assignment -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 25 Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key GF7050V-M7 SE CHAPTER 4: RAID FUNCTIONS 4.1 O PERAT ION SYST EM z Supports Windows XP Home/Prof essional Edition and Windows Vista. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1. 4.3 HOW RAID WORKS RAID 0: The controller “ stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth. Features and Benefits Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the platf orm. Uses: Intended for non-critical data requiring high data throughput, or any env ironment that does not require f ault tolerance. Benefits: prov ides increased data throughput, especially f or large files. No capacity loss penalty f or parity. Drawbacks: Does not deliver any fault tolerance. If any drive in the array f ails, all data is lost. Fault Tolerance: No. Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 19 Motherboard Manual RAID 1: Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media. Features and Benefits Drives: Minimum 2, and maximum is 2. Uses: RAID 1 is ideal f or small databases or any other application that requires f ault tolerance and minimal capacity. Benefits: Prov ides 100% data redundancy. Should one driv e f ail, the controller switches to the other drive. Drawbacks: Requires 2 driv es for the storage space of one driv e. Perf ormance is impaired during driv e rebuilds. Fault Tolerance: Yes. Block 1 Block 2 Block 3 20 Block 1 Block 2 Block 3 GF7050V-M7 SE RAID 0+1: RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1 solution for improved performance plus resiliency. Features and Benefits Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. Benefits: Optimizes for both fault tolerance and perf ormance, allowing for automatic redundancy. May be simultaneously used with other RAID lev els in an array, and allows for spare disks. Drawbacks: Requires twice the available disk space f or data redundancy, the same as RAID level 1. Fault Tolerance: Yes. GeF or ce 7050/ nF orce 610i Block 1 Bl ock 3 Bl ock 5 ※ Bl ock 2 Bl ock 4 Bl ock 6 Bl ock 1 Block 3 Block 5 Block 2 Block 4 Block 6 For more detailed setup information, please refer to the Driver CD, or go to http://www.nvidia.com/object/IO_28159.html to download the NVIDIA RAID User’s Guide. 21 Motherboard Manual CHAPTER 5: USEFUL HELP 5.1 DRIVER INST ALLAT ION NOT E After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you ins ert the Driver CD, please use file brows er to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat R eader to open the manual file. Pleas e download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep 2.html 22 GF7050V-M7 SE 5.2 SOFT WARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility. eHot-Line (Optional) eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Before you use this utility, please set Outlook Express as your default e-mail client application program. re pre sen ts i mp orta nt i n fo rmati on that you m ust p rovi de . With ou t th is in formati on , you may n ot b e abl e to se nd ou t th e ma il . * Th i s bl ock wi ll sho w the in fo rma ti on wh ich wou l d b e co ll ecte d i n the mai l. cri be cond i ti on * Des of yo ur system. ect yo ur are a o r * Sel the a re a cl ose to y ou . Pro vid e th e e -mai l ad dre ss th at yo u w oul d li ke to se nd the cop y to. de the na me o f * Provi the m emory mod ul e manu factur er. Pro vid e th e n ame of the po we r sup pl y man ufactu rer an d th e mod el no . Send th e ma il ou t. Exi t thi s di a log . Sa ve th ese in forma ti o n to a .txt fi le 23 Motherboard Manual After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Sav e”. Your system information will be saved to a .txt file. Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail. We w ill not share customer’s data w ith any other third parties, so please feel free to provide your system information while using eHot-Line service. If you are not using Outlook Express a s your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web http://www.biostar.com.tw/app/en-us/about/contact.php for getting our contact information. 24 GF7050V-M7 SE BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. AWARD BIO S Show current BI OS information AMI BIO S Clear CMOS function (Only for AWARD BIOS) Save current BIOS to a .bin file Update BIOS with a BIOS file <Backup BIOS> Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save. After the saving process, finish dialog will show. Click on OK to complete the BIOS Backup procedure. 25 Motherboard Manual <Update BIOS> Before doing this, please download the proper BIOS file from the website. For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show f or asking you backup current BIOS. Click Yes for BIOS backup and ref er to the Backup BIOS procedure; or click No to skip this procedure. Af ter the BIOS Backup procedure, the open dialog will show f or requesting the BIOS f ile which is going to be updated. Please choose the proper BIOS f ile f or updating, then click on Open. The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process. Af ter the BIOS Update process, click on OK to restart the system. While the system boots up and the f ull screen logo shows, press key to enter BIOS setup. <Delete> In the BIOS setup, use the Load Optimized Defaults function and then Save and Exit Setup to exit BIOS setup. BIOS Update is completed. All the i nfor mati on and content above about the software are subject to be changed without notice. For better perfor mance, the software is being continuously updated. The information and pictures described above are for your refer ence onl y. The actual information and s ettings on board may be slightl y different from this manual. 26 GF7050V-M7 SE 5.3 EXT RA INFORMAT ION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU 0protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again. 27 Motherboard Manual BIO-Flasher BIO-Flasher is a BIOS flashing utility prov iding y ou an easy and simple way to update y our BIOS v ia USB pen drive or f loppy disk. The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12> during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIO-Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, sav e the BIOS f ile into a USB pen driv e or a f loppy disk. 3. Insert the USB pen drive or the f loppy disk that contains the BIOS file to the USB port or the floppy disk drive. 4. Power on or reset the computer and then press <F12> during the POST process. A select dialog as the picture on the right appears. Select the device contains the BIOS file and press <Enter> to enter the utility. 5. The utility will show the BIOS f iles and their respective inf ormation. Select the proper BIOS f ile and press <Enter> then <Y> to perf orm the BIOS update process. 6. Af ter the update process, the utility will ask y ou to reboot the system. Press <Y> to proceed. BIOS update completes. z z 28 This utility only allows storage device with FAT32/16 format and single partition. Shutting down or res etting the s ystem while updating the BIOS will lead to system boot failure. GF7050V-M7 SE 5.4 AMI BIO S BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in f loppy drive A:) “AMIBOOT.ROM” f ile not f ound in root directory of diskette in A: Insert next diskette if multiple diskettes are used f or recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.ROM” f ile size error BIOS ROM image mismatch (file layout does not match image present in f lash device) POST BIOS Beep Codes Number of Beeps 1 3 6 7 8 Description Memory ref resh timer error Base memory read/write test error Key board controller BAT command failed General exception error (processor exception interrupt error) Display memory error (system video adapter) Troubleshooting POST BIOS Beep Codes Number of Beeps 1, 3 6, 7 8 Troubleshooting Action Reseat the memory, or replace with known good modules. Fatal error indicating a serious problem with the system. Consult y our system manufacturer. Bef ore declaring the motherboard beyond all hope, eliminate the possibility of interf erence by a malf unctioning add-in card. Remov e all expansion cards except the v ideo adapter. z If beep codes are generated when all other expansion cards are absent, consult y our system manufacturer’s technical support. z If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malf unction. Insert the cards back into the system one at a time until the problem happens again. This will rev eal the malf unctioning card. If the system video adapter is an add-in card, replace or reseat the video adapter. If the v ideo adapter is an integrated part of the sy stem board, the board may be faulty. 29 Motherboard Manual 5.5 TROUBLESHOOT ING Probable Solution 1. Make sure power cable is No power to the system at all securely plugged in. Power light don’t illuminate, f an inside power supply does not turn 2. Replace cable. on. 3. Contact technical support. 2. Indicator light on key board does not turn on. System inoperativ e. Keyboard lights Using even pressure on both ends of are on, power indicator lights are lit, the DIMM, press down firmly until the and hard driv e is spinning. module snaps into place. 1. System does not boot from hard disk 1. driv e, can be booted f rom optical driv e. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the driv e type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. 1. Back up data and applications System only boots f rom optical driv e. f iles. Hard disk can be read and applications can be used but booting from hard disk 2. Ref ormat the hard driv e. is impossible. Re-install applications and data using backup disks. Screen message says “Invalid Rev iew system’s equipment. Make sure Conf iguration” or “CMOS Failure.” correct inf ormation is in setup. Cannot boot system after installing 1. Set master/slave jumpers second hard driv e. correctly. 2. Run SETUP program and select correct driv e types. Call the drive manuf acturers f or compatibility with other drives. 30 GF7050V-M7 SE This page is intentionally left blank. 31 Motherboard Manual APPENDENCIES: SPEC IN OTHER LANGUAGE GERMAN Spezifikationen LGA 775 CPU Unterstützt Hyper-Threading / Execute Disable Bit Intel Core2Duo / Core2Quad / Celeron 4xx / / Enhanced Intel SpeedStep® / Intel Pentium 4 / Pentium D Prozessoren Architecture-64 / Extended Memory 64 Unterstützt 45nm CPU Technology / Virtualization Technology FSB 1333 MHz Chipsatz GeForce 7050/nForce 610i Grafik GeForce 7050/nForce 610i Max. 512MB gemeinsam benutzter Videospeicher (under OS) Super E/A ITE 8718F Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen. Lüfterdrehzahl-Controller Low Pin Count-Schnittstelle "Smart Guardian"-Funktion von ITE DDR2 DIMM-Steckplätze x 2 Arbeitsspeich er Jeder DIMM unterstützt 256MB/512MB/1GB/ Ein-Kanal DDR2 Speichermodul 2GB DDR2. registrierte DIMMs. ECC DIMMs werden nicht Max. 4GB Arbeitsspeicher unterstützt. Unterstützt DDR2 533 / 667 / 800 IDE Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus Integrierter IDE-Controller Unterstützt PIO-Modus 0~4 Datentransferrate bis zu 3Gb/s SATA Integrierter Serial ATA-Controller Konform mit der SATA-Spezifikation Version 2.0 Unterstützt RAID 0 / 1 / 0+1 LAN 10 / 100 Mb/s Auto-Negotiation Realtek 8201CL PHY Halb-/ Vollduplex-Funktion 5.1-Kanal-Audioausgabe Audio-Codec ALC662 Unterstützt High-Definition Audio Steckplätze 32 PCI Express x16 Steckplatz x1 PCI Express x 1-Steckplatz x1 GF7050V-M7 SE Spezifikationen PCI-Steckplatz x2 Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion x1 Unterstützt die digitale Audioausgabefunktion Onboard-Ans S/PDIF-Ausgangsanschluss chluss CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB-Anschluss x2 System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse Rückseiten-E /A Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 PS/2-Maus x1 Serieller Anschluss x1 VGA-Anschluss x1 LAN-Anschluss x1 USB-Anschluss x4 Audioanschluss x3 Platinengröße 185 mm (B) X 244 mm (L) OS-Unterstüt zung Biostar behält sich das Recht vor, ohne Windows XP / VISTA Ankündigung die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen. 33 Motherboard Manual FRANCE SPEC Prend en charge les technologies LGA 775 UC Processeurs Intel Core2Duo / Core2Quad / Celeron 4xx / Pentium 4 / Pentium D Hyper-Threading / d'exécution de bit de désactivation / Intel SpeedStep® optimisée/ d'architecture Intel 64 / de mémoire étendue 64 Prend en charge le 45nm UC / de virtualisation Bus frontal 1333 MHz Chipset GeForce 7050/nForce 610i Mémoire vidéo partagée maximale de 512 Mo Graphiques GeForce 7050/nForce 610i Super E/S (under OS) ITE 8718F Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée. Contrôleur de vitesse de ventilateur Interface à faible compte de broches Fonction "Gardien intelligent" de l'ITE Fentes DDR2 DIMM x 2 Mémoire principale Chaque DIMM prend en charge des DDR2 de 256Mo/512Mo et 1Go/2Go Module de mémoire DDR2 à mode à simple voie Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en Capacité mémoire maximale de 4 Go Prend en charge la DDR2 533 / 667 / 800 charge Mode principale de Bus Ultra DMA 33 / 66 / 100 / IDE Contrôleur IDE intégré 133 Prend en charge le mode PIO 0~4, Taux de transfert jusqu'à 3 Go/s. SATA Contrôleur Serial ATA intégré : Conforme à la spécification SATA Version 2.0 Prise en charge RAID 0 / 1 / 0+1 LAN 10 / 100 Mb/s négociation automatique Realtek 8201CL PHY Half / Full duplex capability Sortie audio à 5.1 voies Codec audio ALC662 Fentes Connecteur embarqué 34 Prise en charge de l'audio haute définition PCI Express x16 Steckplatz x1 PCI Express x1 Steckplatz x1 Fente PCI x2 Connecteur de disquette x1 Chaque connector prend en charge 2 lecteurs de disquettes GF7050V-M7 SE SPEC Connecteur IDE x1 Connecteur de Port d'imprimante x1 Connecteur SATA x4 Connecteur du panneau avant x1 Connecteur Audio du panneau avant x1 Connecteur d'entrée CD x1 Connecteur de sortie S/PDIF x1 Embase de ventilateur UC x1 Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB x2 Connecteur d'alimentation (24 broches) x1 Connecteur d'alimentation (4 broches) x1 Clavier PS/2 x1 Souris PS/2 x1 E/S du Port série x1 panneau Port VGA x1 arrière Port LAN x1 Dimensions de la carte Port USB x4 Fiche audio x3 Chaque connecteur prend en charge 2 périphériques IDE Chaque connector prend en charge 1 Port d'imprimante Chaque connecteur prend en charge 1 périphérique SATA Prend en charge les équipements du panneau avant Prend en charge la fonction audio du panneau avant Prend en charge la fonction d'entrée audio de CD Prend en charge la fonction de sortie audio numérique Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Alimentation électrique du ventilateur système Chaque connecteur prend en charge 2 ports USB de panneau avant 185mm (l) X 244 mm (H) Support SE Windows XP / VISTA Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis. 35 Motherboard Manual IT ALIAN SPECIFICA LGA 775 CPU Supporto di Hyper -Threadi ng / Execute Processore Intel Core 2Duo / Core 2Quad / Disable Bit / Enha nced I ntel Spee dStep® / Celeron 4xx / Pe ntium 4 / Pentium D Architettura Intel 64 / Tecnologi a Extende d Supporto 45nm CPU Memory 64 / Tec nologia Virtualization FSB 1333 MHz Chipset GeForce 7050/nForce 610i Grafica GeForce 7050/nForce 610i Super I/O La memoria video condivisa massima è di 512MB (under OS) ITE 8718F Funzioni di co ntrollo dell’ambiente: Fornisce le funzio nalità legacy Super I/O Monitoraggio hardware usate più comunemente. Controller velocità ventolina Interfaccia LPC (L ow Pin Count) Funzione "Smart Guardi an" di I TE Alloggi DIMM DDR 2 x 2 Memoria principale Ciascun DIMM supporta DDR 2 256MB/ Modulo di memoria DDR2 a canale singolo 512MB e 1GB/2GB DIMM registrati e DIMM ECC no n sono Capacità massima della memori a 4GB supportati Supporto di DDR2 533 / 667 / 800 Modalità Bus Master Ultra DMA 33 / 66 / 100 IDE Controller IDE i ntegrato / 133 Supporto modalità PIO Mode 0- 4 Velocità di trasferimento dei dati fi no a 3 SATA Gb/s. Controller Serial ATA inte grato Compatibile specifiche SATA Versione 2.0. Supporto RAID 0 / 1 / 0+1 LAN Codec audio Alloggi 36 Negoziazione automatica 10 / 100 Mb/s Realtek 8201CL PHY Capacità Half / Full Duplex Uscita audio 5.1 ca nali ALC662 Supporto audio High- Defi nition (HD) Fente PCI Express x 16 x1 Fente PCI Express x 1 x1 GF7050V-M7 SE SPECIFICA Alloggio PCI x2 Connettore flo ppy x1 Ciascun connettore supporta 2 unità Floppy Connettore IDE x1 Ciascun connettore supporta 2 unità IDE Connettore Porta stampa nte x1 Connettore SATA x4 Ciascun connettore supporta 1 unità SATA Connettore pa nnello fro ntale x1 Supporta i servizi del pa nnell o fr ontale Connettore audio frontale x1 Supporta la funzione a udio pannello fr ontale Connettore CD-in x1 Supporta la funzione i nput audio C D Connettore output SPDIF x1 Supporta la funzio ne d’output a udio digitale Collettore ventolina CPU x1 Collettore ventolina sistema x1 Collettore cancellazione CMOS x1 Connettore USB x2 Connettore alimentazione ( 24 pin) x1 Connettore alimentazione ( 4 pi n) x1 Tastiera PS/2 x1 Mouse PS/2 x1 I/O Porta seriale x1 pannello Porta VGA x1 posteriore Porta LAN x1 Porta USB x4 Connettore audio x3 Connettori su scheda Dimension i scheda supportati stampante Alimentazione ve ntolina CPU (co n funzione Smart Fan) Alimentazione ve ntolina di sistema Ciascun connettore supporta 2 porte USB pannello frontale 185 mm (lar ghezza) x 244 mm (altezza) Sistemi operativi Ciascun connettore supporta 1 P orta Biostar si riserva il diritto di aggiungere o Windows XP / VISTA rimuovere il supporto di qualsiasi sistema operativo se nza pre avviso. 37 Motherboard Manual SPANISH Especificación CPU FSB Conjunto de chips Gráficos LGA 775 Admite Hyper-Threading / Bit de deshabilitación de Procesador Intel Core2Duo / Core2Quad / ejecución / Intel SpeedStep® Mejorado / Intel Celeron 4xx / Pentium 4 / Pentium D Architecture-64 / Tecnología Extended Memory 64 / Admite 45nm CPU Tecnología de virtualización 1333 MHz GeForce 7050/nForce 610i Memoria máxima de vídeo compartida de 512MB GeForce 7050/nForce 610i (under OS) Súper E/S ITE 8718F Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S. Controlador de velocidad de ventilador Interfaz de cuenta Low Pin Función "Guardia inteligente" de ITE Ranuras DIMM DDR2 x 2 Memoria principal Cada DIMM admite DDR de 256MB/512MB y Módulo de memoria DDR2 de canal Sencillo 1GB/2GB No admite DIMM registrados o DIMM compatibles Capacidad máxima de memoria de 4GB con ECC Admite DDR2 de 533 / 667 / 800 IDE Modo bus maestro Ultra DMA 33 / 66 / 100 / 133 Controlador IDE integrado Soporte los Modos PIO 0~4. Tasas de transferencia de hasta 3 Gb/s. SATA Controlador ATA Serie Integrado Compatible con la versión SATA 2.0. Admite RAID 0 / 1 / 0+1 Red Local Códecs de Negociación de 10 / 100 Mb/s Realtek 8201CL PHY Funciones Half / Full dúplex Salida de sonido de 5.1 canales ALC662 sonido Ranuras 38 Soporte de sonido Alta Definición Ranura PCI Express x16 X1 Ranura PCI Express x1 X1 GF7050V-M7 SE Especificación Conectores en placa Ranura PCI X2 Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible Conector IDE X1 Cada conector soporta 2 dispositivos IDE Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Conector SATA X4 Cada conector soporta 1 dispositivos SATA Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Conector de entrada de CD X1 Soporta función de entrada de sonido de CD Conector de salida S/PDIF X1 Soporta función de salida de sonido digital Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Cabecera de ventilador de sistema X1 Cabecera de borrado de CMOS X1 Conector USB X2 Conector de alimentación X1 Fuente de alimentación de ventilador de sistema Cada conector soporta 2 puertos USB frontales (24 patillas) Conector de alimentación X1 (4 patillas) Teclado PS/2 X1 Ratón PS/2 X1 Panel Puerto serie X1 trasero de Puerto VGA X1 E/S Puerto de red local X1 Puerto USB X4 Conector de sonido X3 Tamaño de la placa 185 mm. (A) X 244 mm. (H) Soporte de sistema operativo Windows XP / VISTA Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo. 39 Motherboard Manual PORT UGUESE ESPECIFICAÇÕES CPU LGA 775 Suporta as tecnologias Hyper-Threading / Processador Intel Core2Duo / Core2Quad / Execute Disable Bit / Enhanced Intel Celeron 4xx / Pentium 4 / Pentium D SpeedStep® / Intel Arquitecture -64 / Extended Suporta 45nm CPU Memory 64 / Virtualization FSB 1333 MHz Chipset GeForce 7050/nForce 610i Placa gráfica Memória de vídeo máxima partilhada: 512 MB GeForce 7050/nForce 610i (under OS) ITE 8718F Iniciativas para controlo do ambiente Especificaçã Proporciona as funcionalidades mais utilizadas Monitorização do hardware o Super I/O em termos da especificação Super I/O. Controlador da velocidade da ventoinha Interface LPC (Low Pin Count). Função "Smart Guardian" da ITE Ranhuras DIMM DDR2 x2 Memória principal Cada módulo DIMM suporta uma memória Módulo de memória DDR2 de canal simples DDR2 de 256 MB/512 MB & 1 GB/2 GB Os módulos DIMM registados e os DIMM ECC Capacidade máxima de memória: 4 GB não são suportados Suporta módulos DDR2 533 / 667 / 800 IDE Modo Bus master Ultra DMA 33 / 66 / 100 / 133 Controlador IDE integrado Suporta o modo PIO 0~4. Velocidades de transmissão de dados até 3 Gb/s. SATA Compatibilidade com a especificação SATA Controlador Serial ATA integrado versão 2.0. Suporta as funções RAID 0 / 1 / 0+1 LAN Codec de som Ranhuras 40 Auto negociação de 10 / 100 Mb/s Realtek 8201CL PHY Capacidade semi/full-duplex Saída de áudio de 5.1 canais ALC662 Suporta a especificação High-Definition Audio Ranhura PCI Express x16 x1 Ranhura PCI Express x1 x1 Ranhura PCI x2 GF7050V-M7 SE ESPECIFICAÇÕES Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes Conector IDE x1 Cada conector suporta 2 dispositivos IDE Conector da para impressora x1 Cada conector suporta 1 Porta para impressora Conector SATA x4 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector para entrada de CDs x1 Suporta a entrada de áudio a partir de CDs x1 Suporta a saída de áudio digital Conectores Conector de saída S/PDIF na placa Entradas/S aídas no painel traseiro Tamanho da placa Conector da ventoinha da CPU x1 Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB x2 Conector de alimentação (24 pinos) x1 Conector de alimentação (4 pinos) x1 Teclado PS/2 x1 Rato PS/2 x1 Porta série x1 Porta VGA x1 Porta LAN x1 Porta USB x4 Tomada de audio x3 suportados Smart Fan) Alimentação da ventoinha do sistema Cada conector suporta 2 portas USB no painel frontal 185 mm (L) X 244 mm (A) Sistemas operativos Alimentação da ventoinha da CPU (com a função A Biostar reserva-se o direito de adicionar ou Windows XP / VISTA remover suporte para qualquer sistema operativo com ou sem aviso prévio. 41 Motherboard Manual POLISH SPEC Procesor LGA 775 Obsługa Hyper-Threading / Execute Disable Bit / Procesor Intel Core2Duo / Core2Quad / Enhanced Intel SpeedStep® / Intel Celeron 4xx / Pentium 4 / Pentium D Architecture-64 / Extended Memory 64 Obsługa 45nm Procesor Technology / Virtualization Technology FSB 1333 MHz Chipset GeForce 7050/nForce 610i Grafika GeForce 7050/nForce 610i Maks. wielkość współdzielonej pamięci video wynosi 512MB (under OS) Gniazda DDR2 DIMM x 2 Pamięć główna Każde gniazdo DIMM obsługuje moduły 256MB/ Moduł pamięci DDR2 z trybem pojedynczego 512MB oraz 1GB/2GB DDR2 kanału Maks. wielkość pamięci 4GB Brak obsługi Registered DIMM oraz ECC DIMM Obsługa DDR2 533 / 667 / 800 ITE 8718F Super I/O Funkcje kontroli warunków pracy, Zapewnia najbardziej powszechne funkcje Super Monitor H/W I/O. Kontroler prędkości wentylatora Interfejs Low Pin Count Funkcja ITE "Smart Guardian" IDE Zintegrowany kontroler IDE SATA Zintegrowany kontroler Serial ATA Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master obsługa PIO tryb 0~4 Transfer danych do 3 Gb/s. Zgodność ze specyfikacją SATA w wersji 2.0. Obsługa RAID 0 / 1 / 0+1 10 / 100 Mb/s z automatyczną negocjacją LAN szybkości Realtek 8201CL PHY Działanie w trybie połowicznego / pełnego dupleksu Kodek dźwiękowy Gniazda 42 5.1 kanałowe wyjście audio ALC662 Obsługa High-Definition Audio Gniazdo PCI Express x16 x1 Gniazdo PCI Express x1 x1 Gniazdo PCI x2 GF7050V-M7 SE SPEC Złącza Złącze napędu dyskietek x1 Każde złącze obsługuje 2 napędy dyskietek Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE Złącze Port drukarki x1 Każde złącze obsługuje 1 Port drukarki Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA Złącze panela przedniego x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia audio wbudowane Złącze główkowe wentylatora procesora x1 Fan) Złącze główkowe wentylatora Back Panel I/O Wymiary płyty operacyjne Zasilanie wentylatora systemowego systemowego x1 Złącze główkowe kasowania CMOS x1 Złącze USB x2 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Port szeregowy x1 Port VGA x1 Port LAN x1 Port USB x4 Gniazdo audio x3 Każde złącze obsługuje 2 porty USB na panelu przednim 185 mm (S) X 244 mm (W) Obsluga systemu Zasilanie wentylatora procesora (z funkcją Smart Biostar zastrzega sobie prawo dodawania lub Windows XP / VISTA odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia. go 43 Motherboard Manual RUSSIAN СПЕЦ CPU Поддержка технологий Hyper-Threading / LGA 775 Execute Disable Bit / Enhanced Intel (центральн Процессор Intel Core2Duo / Core2Quad / ый SpeedStep® / Intel Architecture-64 / Extended Celeron 4xx / Pentium 4 / Pentium D Memory 64 Technology / технологии процессор) Поддержка технологий 45nm CPU FSB Набор микросхем Графика виртуализация 1333 МГц GeForce 7050/nForce 610i Максимальная совместно используемая видео GeForce 7050/nForce 610i память составляет 512 МБ (under OS) Слоты DDR2 DIMM x 2 Основная память Каждый модуль DIMM поддерживает 256МБ /512МБ & 1ГБ/2ГБ DDR2 IDE SATA Локальная сеть Звуковой кодек Слоты Встроенны й разъём 44 DDR2 Не поддерживает зарегистрированные Максимальная ёмкость памяти 4 ГБ модули DIMM and ECC DIMM Поддержка DDR2 533 / 667 / 800 Super I/O Модуль памяти с одноканальным режимом ITE 8718F Инициативы по охране окружающей среды, Обеспечивает наиболее используемые Аппаратный монитор действующие функциональные возможности Регулятор скорости Super I/O. Функция ITE "Smart Guardian" Интерфейс с низким количеством выводов (Интеллектуальная защита) Режим "хозяина" шины Ultra DMA 33 / 66 / 100 Встроенное устройство управления / 133 встроенными интерфейсами устройств Поддержка режима PIO 0~4, Встроенное последовательное устройство управления ATA скорость передачи данных до 3 гигабит/с. Соответствие спецификации SATA версия 2.0. Поддержка RAID 0 / 1 / 0+1 Автоматическое согласование 10 / 100 Мб/с Realtek 8201CL PHY Частичная / полная дуплексная способность 5.1канальный звуковой выход ALC662 Звуковая поддержка High-Definition Слот PCI Express x16 x1 Слот PCI Express x1 x1 Слот PCI x2 Разъём НГМД x1 Разъём IDE x1 Каждый разъём поддерживает 2 накопителя на гибких магнитных дисках Каждый разъём поддерживает 2 встроенных интерфейса накопителей GF7050V-M7 SE СПЕЦ Разъём Порт подключения принтера x1 Разъём SATA x4 Разъём на лицевой панели x1 Входной звуковой разъём x1 Разъём ввода для CD x1 Разъём вывода для S/PDIF x1 Каждый разъём поддерживает 1 устройство SATA Поддержка устройств на лицевой панели Поддержка звуковых функций на лицевой панели Поддержка функции ввода для CD Поддержка вывода цифровой звуковой функции Источник питания для вентилятора Контактирующее приспособление вентилятора центрального процессора x1 Контактирующее приспособление вентилятора системы Каждый разъём поддерживает 1 Порт подключения принтера x1 центрального процессора (с функцией интеллектуального вентилятора) Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB-разъём x2 Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Клавиатура PS/2 x1 Задняя Мышь PS/2 x1 панель Последовательный порт x1 средств Порт VGA x1 ввода-выв Порт LAN x1 USB-порт x4 Гнездо для подключения наушников x3 ода Размер панели Поддержка OS Каждый разъём поддерживает 2 USB-порта на лицевой панели 185 мм (Ш) X 244 мм (В) Biostar сохраняет за собой право добавлять Windows XP / VISTA или удалять средства обеспечения для OS с или без предварительного уведомления. 45 Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت Hyper-Threading / Execute Disable Bit /ﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت LGA 775 وﺣﺪة اﻟﻤﻌ ﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ Intel Core2Duo / Core2Quad / Celeron 4xxﻡﻌ ﺎﻟﺠﺎت Enhanced Intel SpeedStep® / Intel ﺑ ﺘﺮدد ﻳﺼﻞ إﻟﻰ/ Pentium 4 / Pentium D Architecture-64 / Extended Memory 64 45nm CPUﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت Technology / Virtualization Technology اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ﻡﻴﺠﺎ هﺮﺕﺰ 1333ﺕﺮدد ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ GeForce 7050/nForce 610i ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت GeForce 7050/nForce 610i ﻡﻴﺠﺎ ﺑﺎﻳﺖ)512(under OSأﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ 2ﻋﺪدDDR2 DIMMﻓﺘﺤ ﺔ ﻡﻴﺠﺎ 256/512ﺳﻌﺔ DDR2ﺕﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮعDIMMﺕﺪﻋﻢ آﻞ ﻓﺘﺤﺔ أﺣﺎدﻳﺔ اﻟﻘﻨﺎةDDR2وﺣﺪة ذاآﺮة اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﺑﺎﻳﺖ و 2/1ﺝﻴﺠﺎ ﺑﺎﻳﺖ ECCوﺕﻠﻚ اﻟﺘﻲﻻ ﺕﺘﻮاﻓﻖ ﻡﻊDIMMﻻ ﺕﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 4ﺝﻴﺠﺎ ﺑﺎﻳﺖ ﻡﻴﺠﺎ ﺑﺎﻳﺖ533 / 667 / 800 ﺳﻌﺎتDDR2ﺕﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ: ITE 8718F Super I/O ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣ ﺎﻟﺔ اﻷﺝﻬﺰة اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎ Super I/O .ﺕﻮﻓﺮ وﻇﻴﻔﺔ ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ Low Pin Count Interfaceﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ ITEﻡﻦ""Smart Guardianوﻇﻴﻔﺔ Ultra DMA 33 / 66 / 100 / 133ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ ﻡﻨﻔﺬ IDE ﻡﺘﻜﺎﻡﻞIDEﻡﺘﺤﻜﻢ SATA ﻡﺘﻜﺎﻡﻞSerial ATAﻡﺘﺤﻜﻢ وﺿﻊ رﺋﻴﺴﻲ PIO Mode 0~4دﻋﻢ وﺿﻊ ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺕﺼﻞ إﻟﻰ 3ﺝﻴﺠﺎﺑﺖ /ﺙﺎﻥﻴﺔ. 2.0.اﻹﺹﺪارSATAﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت RAID 0 / 1 / 0+1ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ ﺵﺒﻜﺔ دا ﺥﻠﻴﺔ ﺕﻔﺎوض ﺕﻠﻘﺎﺋﻲ 100/10ﻡﻴﺠﺎ ﺑﺎﻳﺖ /ﺙﺎﻥﻴﺔ Realtek 8201CL PHY 100/10 آﻮدﻳﻚ اﻟﺼﻮت إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ/اﻟﻨﺼﻔﻲ ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت5.1 ALC662 ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ اﻟﺼﻮت ﻋ ﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻡﻦ اﻟﻔﺘﺤﺎت ﻓﺘﺤﺔ PCI Expressx16 ﻋﺪد 1 ﻓﺘﺤﺔ PCI Expressx1 ﻋﺪد 1 ﻓﺘﺤﺔ PCI ﻋﺪد 2 46 GF7050V-M7 SE اﻟﻤﻮاﺻﻔﺎت ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ ﻡﻨﻔﺬIDE ﻋﺪد 1 IDEﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ ﻋﺪد 1 ﻡﻨﻔﺬSATA ﻋﺪد 4 SATAﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﺕﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ ﻡﻨﻔﺬCD-IN ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ اﻟﻠﻮﺣﺔ ﻡﻨﻔﺬ ﺥﺮجS/PDIF ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ ﻋﺪد 1 (Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌ ﺎﻟﺠﺔ ) ﻡﻊ وﻇﻴﻔﺔ وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم وﺹﻠﺔ ﻡﺴﺢCMOS ﻋﺪد 1 ﻡﻨﻔﺬUSB ﻋﺪد 2 ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ﻋﺪد 1 ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ) 4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻡﻔﺎﺕﻴﺢPS/2 ﻋﺪد 1 ﻡﺎوس PS/2 ﻋﺪد 1 ﻡﻨﻔﺬ ﺕﺴﻠﺴﻠﻲ ﻋﺪد 1 ﻡﻨﻔﺬ VGA ﻋﺪد 1 ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺕﺼﺎل ﻡﺤﻠﻴﺔ ﻋﺪد 1 ﻡﻨﺎﻓﺬ USB ﻋﺪد 4 ﻡﻘﺒﺲ ﺹﻮت ﻋﺪد 3 ﻡﻨﺎﻓﺬ دﺥﻞ /ﺥﺮج اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﺣﺠﻢ اﻟﻠﻮﺣﺔ دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔUSBﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ 185ﻡﻢ )ﻋﺮض ( 244 Xﻡﻢ ) ارﺕﻔﺎع( Windows XP / VISTA ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أوBiostarﺕﺤﺘﻔﻆ ﺑﺪون إﺥﻄﺎر. 47 Motherboard Manual JAPANESE 仕様 Hyper-Threading / Execute Disable Bit / LGA 775 CPU Intel Core2Duo / Core2Quad / Celeron 4xx / Pentium 4 / Pentium D processor Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technologyをサポート 45nm CPU をサポートします します FSB 1333 MHz チップセット GeForce 7050/nForce 610i グラフィック GeForce 7050/nForce 610i 最大の共有ビデオメモリは512MBです (under OS) ス DDR2 DIMMスロット x 2 各DIMMは256MB/512MB/1GB/2GB DDR2をサポ シングル チャンネルモードDDR2メモリモジュール メインメモリ ート 登録済みDIMMとECC DIMMはサポートされません 最大メモリ容量 4GB DDR2 533 / 667 / 800 をサポート ITE 8718F Super I/O IDE 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O機能を H/Wモニター 採用しています。 ファン速度コントローラ/ モニター 低ピンカウントインターフェイス ITEの「スマートガーディアン」機能 Ultra DMA 33 / 66 / 100 / 133バスマスタモード 統合IDEコントローラ PIO Mode 0~4のサポート 最高3 Gb/秒のデータ転送速度 SATA SATAバージョン2.0仕様に準拠。 統合シリアルATAコントローラ RAID 0 / 1 / 0+1 のサポート 10 / 100 Mb/秒のオートネゴシエーション 10/100 LAN Realtek 8201CL PHY 半/全二重機能 サウンド Codec スロット 48 5.1チャンネルオーディオアウト ALC662 ハイデフィニションオーディオのサポート PCI Express x16スロット x1 PCI Express x1スロット x1 PCIスロット x2 GF7050V-M7 SE 仕様 フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートし ます IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします x1 CDオーディオイン機能をサポートします S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x2 オンボードコ CDインコネクタ ネクタ 各コネクタは2つのフロントパネルUSBポートをサポ ートします 背面パネル I/O 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 シリアルポート x1 VGAポート x1 LANポート x1 USBポート x4 オーディオジャック x3 ボードサイズ 185 mm (幅) X 244 mm (高さ) OSサポート Windows XP / VISTA Biostarは事前のサポートなしにOSサポートを追加ま たは削除する権利を留保します。 2008/03/12 49
