Download Sub-Zero Design Guide
Transcript
INTERNATIONAL DESIGN GUIDE Contents Built-In Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PRO 48 Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . 34 Integrated Refrigeration . . . . . . . . . . . . . . . . . . . . . . . 39 Wine Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information. Built-In Refrigeration 914 mm 3 914 mm 914 mm subzero.com/specs 914 mm Built-In Refrigeration. For the built-in line, Sub-Zero designers and engineers took a fresh look at everything, 2134 2134 mm mm inside and out. Exterior refinements include redesigned grilles and lower-profile hinges. Inside, new technology in food preservation makes the built-in line nothing short of revolutionary. BUILT-IN MODELS 914 mm 762 mm 914 mm 914 mm 2134 2134 mm mm 762 mm 914 mm 2134 mm ICBBI-36R 762 mm 914 mm ICBBI-36F ICBBI-30U 914 mm 1067 mm 914 mm 1067 mm 2134 2134 mm mm ICBBI-36U 10671219 mm mm 1067 mm 1219 mm 1219 mm 2134 mm ICBBI-36S 914 mm ICBBI-42S 1067 mm ICBBI-42SD 1067 mm ICBBI-48S 1219 mm ICBBI-48SD 1219 mm KEY FEATURES • Three distinct design approaches: overlay, flush inset and stainless steel. 2134 •mm Handle options coordinate with handles of Wolf cooking products. • Dual refrigeration; two compressors preserve food’s goodness in two sealed compartments. • Energy efficient. • Advanced air purification system. • Crisper and deli drawers form a lower-temperature zone for produce and meats. • Flip-up grille provides easy access for quick routine maintenance. • All models are Star-K certified. 1219 mm Built-In Refrigeration 4 Built-In Models All Refrigerator / All Freezer Models SPECIFICATIONS OVERALL DIMENSIONS Interior Capacity R (L) F (L) ICBBI-36R 662 ICBBI-36F 640 914 mm 610 mm ALL REFRIGERATOR / ALL FREEZER MODELS OVER-AND-UNDER MODELS ICBBI-30U ICBBI-36U 362 451 116 149 346 455 453 533 531 227 227 230 270 274 SIDE-BY-SIDE MODELS ICBBI-36S ICBBI-42S ICBBI-42SD ICBBI-48S ICBBI-48SD 2134 mm 1873 mm Shipping Weight kg ALL REFRIGERATOR / ALL FREEZER MODELS ICBBI-36R ICBBI-36F 191 184 OVER-AND-UNDER MODELS ICBBI-30U ICBBI-36U 210 234 HEIGHT DIMENSIONS ± 13 SIDE-BY-SIDE MODELS ICBBI-36S ICBBI-42S ICBBI-42SD ICBBI-48S ICBBI-48SD 244 264 276 286 298 mm 102 mm 606 mm 606 mm 432 mm 946 mm 60 mm MODELS ICBBI-36R AND ICBBI-36F Shipping weights and overall dimensions are based on stainless steel models. For flush inset applications, add 13 mm to door clearance dimensions. Built-In Refrigeration 5 subzero.com/specs Over-and-Under Models OVERALL DIMENSIONS 762 mm 610 mm 914 mm 610 mm 2134 mm 2134 mm HEIGHT DIMENSIONS ± 13 1289 mm 1289 mm 584 mm 584 mm mm 102 mm HEIGHT DIMENSIONS ± 13 606 mm 102 mm 606 mm 606 mm 368 mm 600 mm mm 432 mm 796 mm 600 mm 946 mm 60 mm 60 mm MODEL ICBBI-30U MODEL ICBBI-36U 606 mm Built-In Refrigeration 6 Side-by-Side Models OVERALL DIMENSIONS 914 mm 610 mm 1067 mm 610 mm 2134 mm 2134 mm 1873 mm HEIGHT DIMENSIONS ± 13 mm 1873 mm 102 mm HEIGHT DIMENSIONS ± 13 606 mm mm 102 mm 606 mm 216 mm 260 mm 606 mm 222 mm 318 mm 565 mm 668 mm 60 mm 60 mm MODEL ICBBI-36S Overall dimensions are based on stainless steel models. For flush inset applications, add 13 mm to door clearance dimensions. MODELS ICBBI-42S AND ICBBI-42SD 606 mm Built-In Refrigeration 7 subzero.com/specs Side-by-Side Models OVERALL DIMENSIONS 1219 mm 610 mm 2134 mm 1873 mm HEIGHT DIMENSIONS ± 13 mm 102 mm 606 mm 248 mm 356 mm 762 mm 60 mm MODELS ICBBI-48S AND ICBBI-48SD 606 mm Built-In Refrigeration 8 Built-In Models STANDARD INSTALLATION TOP VIEW 620 mm MINIMUM OPENING DEPTH 620 mm MINIMUM OPENING DEPTH SIDE VIEW 2127 mm OPENING HEIGHT A OPENING WIDTH FRONT VIEW Opening Width A IMPORTANT NOTE: If two units are installed side by side, ICBBI-36R and ICBBI-36F 902 mm refer to pages 21–22 for dual standard installations. ICBBI-30U 746 mm Stainless steel models are ready to install out of the box. ICBBI-36U 902 mm ICBBI-36S 902 mm ICBBI-42S and ICBBI-42SD 1054 mm ICBBI-48S and ICBBI-48SD 1206 mm Built-In Refrigeration 9 subzero.com/specs Planning Information ELECTRICAL REQUIREMENTS PLUMBING REQUIREMENTS International models from the factory designed without a transformer require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device. For built-in models with an automatic ice maker, a pressure limiting valve and 5 meters of flexible 6mm pipe with fittings is included in the refrigerator carton. Connect the pressure limiting valve close to the water tap, CHECKING THE WATER FLOW IS IN THE RIGHT DIRECTION. Ensure water connection is ½” BSP male threaded outlet. Tape the 6mm water line to the wall and floor to ensure it isn’t squashed when the refrigerator is pushed into the cavity. Locate the water tap either in the cabinet above a minimum of 2200mm from the floor, or in the cabinet alongside. The water line must not interfere with installation of the anti-tip brackets. Built-in models should have the electrical supply either in the cabinet above the refrigerator a MINIMUM OF 2200MM ABOVE THE FLOOR or in the cabinet alongside. If freestanding then locate the power point as per the diagram below. A separate circuit servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. IMPORTANT NOTE: A reverse osmosis system can be used provided there is constant water pressure of 2.1 bar to 6.9 bar supplied to the unit at all times. Electrical Requirements Power Supply Plumbing Requirements 220-240 V AC, 50/60 Hz Circuit Breaker 10 amp Receptacle 3-prong grounding-type 1. 1. Water Supply Line 6mm plastic line Water Pressure 2.1–6.9 bar Water line for Connection 5m FRONT VIEW 1. 178 mm 2,200 mm minimum FROM FLOOR pressure pressure limitinglimiting valve valve 6mm flexi hose 6mm flexi hose & tape &totape wall to wall & floor.& floor. 2. 2. Built in. Alternative location of power & water supply depending on ease of access. pressure pressure limiting valve valve limiting 6mm flexi 6mmhose flexi hose & tape&to wallto wall tape & floor. & floor. 1. Built in. Water supply above fridge. Location of 6mm flexible hose. Tape to wall and floor with pressure limiting valve next to tap. 2. 2. Built in. Water supply beside fridge. Location of 6mm flexible hose. Tape to wall and floor with pressure limiting valve next to tap. E 152 mm 1918 mm FROM FLOOR Freestanding location of power supply. Built-In Refrigeration 10 Overlay Panels If you and your client have ordered an overlay model, you will be adding panels and handles to give the unit a more custom look. The overlay panel design option is available for all built-in overlay models. For exact door panel dimensions, refer to overlay panel specifications on the following pages. IMPORTANT NOTE: Overlay models can be used in an overlay or a flush inset application. Be aware that the application specified will affect panel sizes, rough opening dimensions and installation. The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. The most common way to achieve this look is to work with three panels—the decorative overlay panel, which is typically 19 mm, a 3 mm spacer panel and a 6 mm backer panel. Depending on your cabinet manufacturer, this could also be one panel routed for different dimensions. The illustrations provide a cross section view of the threepanel assembly, showing placement of the trim and a rear view of the three-panel assembly with critical dimensions, standard for all built-in models. Overlay grille panels for the panel grille match the design of the overlay door panels. Dimensions for the grille panel are listed in the overlay panel specifications on the following pages. IMPORTANT NOTE: When installing two units in a side-byside application, refer to pages 21–22 for dual standard installations. Be aware that rough opening dimensions are different for this application. Do not exceed overlay panel dimensions, as this could cause damage to panels and the Sub-Zero unit. NOT APPLICABLE IN AUSTRALIA Regardless of the physical construction of the panels (three-panel assembly or routed panel), you will need to follow the overlay panel specifications on the following pages for exact sizing and panel placement to ensure a proper fit. Overlay Panel Requirements MAX WEIGHT PER PANEL All Overlay Models Grille Panel 23 kg 6 kg 16 mm SPACER PANEL OVERLAY PANEL BACKER PANEL BACKER PANEL TRIM 8 mm min 3 mm MIN PANEL THICKNESS All Overlay Panels OVERLAY PANEL SPACER PANEL 19 mm typical 6 3 mm mm Panel assembly cross section. Panel assembly rear view. Built-In Refrigeration 11 subzero.com/specs Overlay Panels H H H A H A H A A H A H W H W ICBBI-30U / ICBBI-36U Model ICBBI-30U Model ICBBI-36U H REFRIGERATOR W H REFRIGERATOR W 914 mm 892 mm 908 mm H 1273 mm 1253 mm 1268 mm W 914 mm 892 mm 908 mm H 483 mm 459 mm 475 mm W 914 mm 892 mm 908 mm H 235 mm* 211 mm 227 mm NOT APPLICABLE IN AUSTRALIA Overlay Panel Spacer Panel Backer Panel HFREEZER Overlay Panel Spacer Panel Backer Panel A B GRILLE Overlay Panel Spacer Panel Backer Panel 762 mm 740 mm 756 mm W 762 mm 740 mm 756 mm 1273 mm 1253 mm 1268 mm H 483 mm 459 mm 475 mm WH 762 mm 740 mm 756 mm 235 mm* 211 mm 227 mm Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel W *Panel height may be increased by 13 mm to hide upper main frame. For more information, refer to the built-in panel configurator at subzero.com/trade/panels. Grille panel dimensions listed are for a standard 2134 mm finished height. For a 2108 mm finished height, subtract 25 mm from grille panel height dimensions. For a 2235 mm finished height, add 102 mm to height dimensions. A 2108 mm or 2235 mm panel grille must be ordered to accept a 2108 mm or 2235 mm custom panel. Width dimensions do not vary. H H A A AH H A A H H A AH A A H A Built-In Refrigeration 12 H W W B B W W W H W W H H W Overlay Panels H H H H H H H H A A B W W W W W B W ICBBI-36S / ICBBI-42S / ICBBI-48S W W ICBBI-48SD Model ICBBI-36S Models ICBBI-48S and ICBBI-48SD REFRIGERATOR W H REFRIGERATOR W H NOT APPLICABLE IN AUSTRALIA Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel 510 mm 487 mm 503 mm W 398 mm 376 mm 392 mm W 914 mm 892 mm 908 mm 1772 mm 1751 mm 1767 mm H 1772 mm 1751 mm 1767 mm H 235 mm* 211 mm 227 mm Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel ICBBI-48SD Dispenser Cut-Out Model ICBBI-42S REFRIGERATOR Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel W 637 mm 614 mm 630 mm W 424 mm 402 mm 418 mm W 1067 mm 1045 mm 1060 mm H 1772 mm 1751 mm 1767 mm H 1772 mm 1751 mm 1767 mm H 235 mm* 211 mm 227 mm Cut-Out Location 730 mm 708 mm 724 mm 1772 mm 1751 mm 1767 mm W 483 mm 460 mm 476 mm H 1772 mm 1751 mm 1767 mm W 1219 mm 1197 mm 1213 mm H 235 mm* 211 mm 227 mm W 149 mm H 316 mm AB 51 mm 732 mm *Panel height may be increased by 13 mm to hide upper main frame. For more information, refer to the built-in panel configurator at subzero.com/trade/panels. Grille panel dimensions listed are for a standard 2134 mm finished height. For a 2108 mm finished height, subtract 25 mm from grille panel height dimensions. For a 2235 mm finished height, add 102 mm to height dimensions. A 2108 mm or 2235 mm panel grille must be ordered to accept a 2108 mm or 2235 mm custom panel. Width dimensions do not vary. Built-In Refrigeration 13 subzero.com/specs Flush Inset Application It is necessary to consider the following points when planning for a flush inset application: • The flush inset depth is 56 mm deeper than the standard opening. • The flush inset width is 64 mm wider than the standard opening. STANDARD INSTALLATION STANDARD INSTALLATION 620 mm minimum 620 mm minimum OPENING DEPTH • The flush inset height is 6 mm higher than the standard opening. 620 mm minimum OPENING DEPTH TOP VIEW FLUSH INSET INSTALLATIONFLUSH INSET INSTALLATION WITH 19 mm PANEL WITH 19 mm PANEL 620 mm 675 mm minimum minimum OPENING DEPTH TOP VIEW TOP VIEW 56 mm IMPORTANT NOTE: The flush inset application is not a separate model. This is an overlay unit in a flush installation. The same model is used in an overlay or flush inset application. Rough opening dimensions for the flush inset application assume the use of a 19 mm decorative panel. The illustrations at right show the difference between standard and flush inset installations. Standard installation. FLUSH INSET DEPTH TOP VIEW 56 32mm mm • Panel widths increase to achieve the flush inset look. • You must allow a 13 mm reveal around the perimeter of the unit and grille to allow for proper door swing and airflow. 675 mm minimum OPENING FLUSH INSETDEPTH DEPTH Flush inset installation. 32 m Built-In Refrigeration 14 620 mm 675 minimum mm minimum OPENING FLUSH INSET DEPTH Built-In Models CLEAT DEPTH TO CLEAT 76 mm FLUSH INSET INSTALLATION typical 56 mm TOP VIEW 32 mm 675mm 620 mm minimum minimum FLUSH INSET DEPTH TOP VIEW DEPTH TO CLEAT 32 mm 620 mm 675 minimum mm minimum OPENING UNIT WITH 19 mm PANEL FLUSH INSET DEPTH CLEAT TOP VIEW CLEAT DEPTH TO CLEAT 76 mm typical DETAIL A 56 mm 56 mm 6 mm 32 mm CLEAT 620 mm minimum DEPTH TO CLEAT 675 mm minimum Detail A 56 mm FLUSH INSET DEPTH 76 mm typical CLEAT SHADED AREA MUST BE FINISHED 102 mm 2127 mm HEIGHT TO CLEAT 2134 mm A 32 mm WIDTH TO CLEAT B FLUSH INSET WIDTH FLUSH INSET HEIGHT 32 mm 620 mm minimum OPENING DEPTH TO CLEAT 56 mm CLEAT 32 mm Detail B 76 mm typical 102 mm SHADED AREA MUST BE FINISHED 620 mm minimum OPENING DEPTH TO CLEAT DETAIL B SIDE VIEW Flush Inset Opening Widths 56 mm 32 mm FRONT VIEW A B ICBBI-30U and ICBWS-30 746 mm 813 mm ICBBI-36U 902 mm 965 mm ICBBI-36S 902 mm 965 mm ICBBI-42S 1054 mm 1118 mm ICBBI-48S, ICBBI-48SD & ICBBI-48SID 1206 mm 1270 mm IMPORTANT NOTE: Dimensions assume a 19 mm panel thickness. IMPORTANT NOTE: If two units are installed side by side, refer to pages 23–27 for dual flush inset installations. Built-In Refrigeration 15 subzero.com/specs Flush Inset Panels The flush inset application allows decorative panels on the front of the unit to be flush with surrounding cabinetry and is available for all built-in overlay models. For exact panel dimensions, refer to flush inset panel specifications on the following pages. The flush inset design allows decorative panels to cover the door trim for a seamless appearance that blends with the design of the room. The most common way to achieve this look is to work with three panels—the decorative flush inset panel, which is typically 19 mm, a 3 mm spacer panel and a 6 mm backer panel. Depending on your cabinet manufacturer, this could also be one panel routed for different dimensions. Regardless of the physical construction of the panels (three-panel assembly or routed panel), you will need to follow the flush inset panel specifications on the following pages for exact sizing and panel placement to ensure a proper fit. The illustration below provides a rear view of the threepanel assembly with critical dimensions, standard for all built-in models. IMPORTANT NOTE: The inside edges of the rough opening as well as the sides and a portion of the back side of the decorative panels will need to be finished, as they will be exposed when the doors are open. IMPORTANT NOTE: For flush inset panels thicker than 19 mm, a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale templates at the end of this section. IMPORTANT NOTE: When installing two units side by side in a flush inset application, refer to pages 23–27 for dual flush inset installations. Be aware that rough opening dimensions, panel sizes and offsets are different for this application. FLUSH INSET PANEL SPACER PANEL Do not exceed flush inset panel dimensions, as this could cause damage to panels and the Sub-Zero unit. BACKER PANEL Flush Inset Panel Requirements MAX WEIGHT PER PANEL All Flush Inset Models Grille Panel 23 kg 6 kg MIN PANEL THICKNESS All Flush Inset Panels 19 mm typical 3 mm 6 mm 16 mm Three-panel assembly. TOP VIEW Built-In Refrigeration TOP VIEW DOOR / DRAWER / GRILLE BACKER SPACER TOP VIEW TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE BACKER CABINETRY SPACER 16 CABINETRY DOOR DOORDOOR TOP VIEW DOOR TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE DOOR / DRAWER / GRILLE FLUSH INSET PANEL FLUSH INSET PANEL Flush Inset Panels PANEL OFFSETS 8 mm BACKER SPACER 16 SPACER TOP VIEW mm DOOR / DRAWER / GRILLE INSET PANEL Illustrations A–F provide panel offsets and revealsFLUSH for all built-in models in a flush inset application. Refer to the 8 mm chart below for reference to the illustrations relating to BACKER SPACER your specific model. CABINETRY Grille Top A C CABINETRY D E F GRILLE Door Bottom / Drawer Top Drawer Bottom Doors (hinge) / Grille Sides GRILLE A CABINETRY B C D F Doors (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom mm GRILLE 8 mm 13 13 mm CABINETRY 16 16 SPACER mm 16 mm CABINETRY 3 mm 8 mm GRILLE CABINETRY DOOR 6 mm 16 mm 6 mm REVEAL 3 mm SIDE VIEW GRILLE 8 mm CABINETRY 3 mm 8 mm GRILLE SIDE VIEW 8 mm4 DRAWER 2 mm 8 mm mm DOOR 8 mm DRAWER 24 E Illus. mm mm 8 mm DOOR SIDE VIEW 16 mm 4DRAWER mm 8 mm SIDE VIEW 8 mm GRILLE 4 mm 3 mm 8 mm REVEAL 8 mm GRILLE 4 mm 13 mm 13 mm 13 mm 13 8 DOOR mm2 GRILLE mm4 8 mm mm DOOR GRILLE 3 mmVIEW SIDE 8 mm 8 mm 2 4 mm 8 mm mm SIDE VIEW SIDE VIEW 13 mm 13 m 8 mm 2DOOR 4 GRILLE mm 8 mm mm DOOR GRILLE 3 SIDEmm VIEW 8 mm 2 4 mm 8 mm mm SIDE VIEW SIDE VIEW 13 mm 8 mm DOOR SIDE VIEW 13 2 DOOR mm 8 mm Illus. D 8 mm DOOR 6 mm REVEAL 13 mm 13 mm 2 mm 8 mm 3 mm 6 mm mm 13 mm 16 mm DRAWER 8 mm DOOR 3DOOR mm Illus. B SIDE VIEW DOOR 8 mm DOOR 3 mm 8 mm 3 mm 13 13 mm 16 mm DRAWER TOP VIEW REVEAL REVEAL 8 mm 13 mm SIDE VIEW DOOR DOOR 6 mm FLUSH INSET PANEL 8 mm DRAWER 6 mm mm Illus. C DOOR 8 mm DOOR DOOR 3 mm TOP VIEWREVEAL Illus. A Grille Bottom / Door Top SIDE-BY-SIDE TOP VIEW 16 8 mm 3 DOOR mm DOOR / DRAWER / GRILLE FLUSH INSET PANEL Illus. OVER-AND-UNDER Door / Drawer / Grille Sides 13 mm CABINETRY mm CABINETRY BACKER INSET PANEL For additional information on model-specific panelFLUSH reveals, visit the specification library section of our website, 8 mm subzerotrade.com. Panel Offsets 8 mm 13 mm BACKER CABINETRY DOOR / DRAWER 2 mm 8 mm SIDE VIEW DOOR / DRAWER SIDE VIEW 2 mm 16 mm DOOR / DRAWER 8 mm 4 2 mm 8 mm mm SIDE VIEW SIDE VIEW DOOR / DRAWER 16 mm 8 mm 42 mm mm 8 mm SIDE VIEW 16 8 mm DOOR / DRAWER 2 mm SIDE VIEW 8 DOOR / mm DRAWER 8 mm 8 mm m Illus. F mm SIDE VIEW 4 mm 8 mm SIDE VIEW SIDE VIEW 2 8 mm mm 2 mm SIDE VIEW SIDE VIEW m 8 mm m Built-In Refrigeration 17 subzero.com/specs Flush Inset Panels H H H A H A H A A H A H W H W ICBBI-30U / ICBBI-36U Model ICBBI-30U Model ICBBI-36U H REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel HFREEZER Flush Inset Panel Spacer Panel Backer Panel A B GRILLE Flush Inset Panel Spacer Panel Backer Panel W 787 mm 740 mm 756 mm W 787 mm 740 mm 756 mm H 1273 mm 1253 mm 1268 mm H 483 mm 459 mm 475 mm WH 787 mm 740 mm 756 mm 235 mm 211 mm 227 mm REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel W 940 mm 892 mm 908 mm H 1273 mm 1253 mm 1268 mm W 940 mm 892 mm 908 mm H 483 mm 459 mm 475 mm W 940 mm 892 mm 908 mm H 235 mm 211 mm 227 mm W Grille panel dimensions listed are for a standard 2134 mm finished height. For a 2108 mm finished height, subtract 25 mm from grille panel height dimensions. For a 2235 mm finished height, add 102 mm to height dimensions. A 2108 mm or 2235 mm panel grille must be ordered to accept a 2108 mm or 2235 mm custom panel. Width dimensions do not vary. H H A HA A H A A H H A HA A A H A Built-In Refrigeration 18 H W W B B W W W H W W H H W Flush Inset Panels H H H H H H H H A A B W W W WW B W W ICBBI-36S / ICBBI-42S / ICBBI-48S W ICBBI-48SD Model ICBBI-36S Models ICBBI-48S and ICBBI-48SD REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel W 522 mm 487 mm 503 mm W 411 mm 376 mm 392 mm W 940 mm 892 mm 908 mm H 1770 mm 1751 mm 1767 mm H 1770 mm 1751 mm 1767 mm H 235 mm 211 mm 227 mm REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel DISPENSER (ICBBI-48SD) Cut-Out Model ICBBI-42S Cut-Out Location REFRIGERATOR W H Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel 649 mm 614 mm 630 mm W 437 mm 402 mm 418 mm W 1092 mm 1045 mm 1060 mm 1770 mm 1751 mm 1767 mm H 1770 mm 1751 mm 1767 mm H 235 mm 211 mm 227 mm W 743 mm 708 mm 724 mm H 1770 mm 1751 mm 1767 mm W 495 mm 460 mm 476 mm H 1770 mm 1751 mm 1767 mm W 1245 mm 1197 mm 1213 mm H 235 mm 211 mm 227 mm W H 149 mm 316 mm A 51 mm B 732 mm Grille panel dimensions listed are for a standard 2134 mm finished height. For a 2108 mm finished height, subtract 25 mm from grille panel height dimensions. For a 2235 mm finished height, add 102 mm to height dimensions. A 2108 mm or 2235 mm panel grille must be ordered to accept a 2108 mm or 2235 mm custom panel. Width dimensions do not vary. Built-In Refrigeration 19 subzero.com/specs Dispenser MODEL ICBBI-48SD The refrigerator door panel must include a cut-out to accommodate the dispenser glasswell and bezel. The thickness of the panel in this area can range from 6 mm to a maximum of 29 mm. IMPORTANT NOTE: Regardless of the thickness of the panel for model ICBBI-48SD, you must plan for a flat landing area for the decorative bezel surrounding the glasswell area. The illustration to the right provides exact bezel dimensions. Refer to the appropriate panel specifications page for exact cut-out location. This landing area can be accomplished in a number of different ways. For overlay and flush inset models, mounting placement of the refrigerator door handle must assure proper access to the glasswell and adequate clearance under the handle. The handle placement illustration shows the relation of the refrigerator door handle to the glasswell bezel on stainless steel models. 16 mm One option (flush) is to rout the panel so the bezel will be flush with rails and stiles. You must rout a space to accommodate the height and width of the bezel. The width of the stile immediately to the left of the bezel must be 44 mm. Do not cut the entire stile to this dimension. The other option (proud) shows a boxed out landing area for the bezel using stiles and rails to create this space. In this application, the bezel will sit proud of the stiles and rails. The total thickness of the panels at this level must not exceed 29 mm. 2 mm 160 mm 25 mm 3 mm GLASSWELL RADIUS 51 mm 327 mm Dispenser dimensions. Handle placement. HANDLE Built-In Refrigeration 20 Side Panels Side panels can be used with every design application. When planning for side panels with the installation of a built-in model, you need to be aware of the space configuration to achieve a pleasing fit. Depending on the exact panel you are using with your unit, the height of the panel may vary. IMPORTANT NOTE: The use of side panels may change the width of your rough opening. The side panel will need to be a minimum of 620 mm minimum deep and 13 mm thick. Refer to the illustrations below for side panel dimensions. Routing will be necessary so that the side panel fits flush against the side of the unit. 620 mm minimum FRONT OF SIDE PANEL ROUT TO 3 48 mm 2134 mm 25 mm (OVER-AND-UNDER MODELS) 146 mm 521 mm 102 mm OPTIONAL TOE KICK CUT-OUT MAIN FRAME Routing detail. 108 mm 5 mm 48 mm 3 mm 13 mm mm ROUT TO 25 mm 67 mm Side panel dimensions. SIDE PANEL ROUTING IMPORTANT NOTE: If you have a model ICBBI-30U or ICBBI-36U, extra routing will be necessary to prevent the panel from hitting the refrigerator lower hinge plate. When installing a built-in unit with a custom side panel, an accessory kit (7003407) is required. Stainless steel and white enamel side panels are also available through your authorized Sub-Zero dealer. Built-In Refrigeration 21 subzero.com/specs Dual Installation STANDARD APPLICATION Dual Installation Panel Requirements Two overlay or stainless steel units may be placed side by side in a dual installation. Some standard applications will require a dual installation kit, available through your authorized Sub-Zero dealer. If you are installing two units side by side in a flush inset application, refer to page 23. MAX WEIGHT PER PANEL All Models Dual Wide Grille Panel MIN PANEL THICKNESS Overlay and Flush Inset Panels A custom filler strip can be used between two units in an overlay or stainless steel design application. It is recommended that the filler strip be at least 51 mm wide to prevent condensation between the units. Be sure to add the filler strip width to your rough opening width. Refer to the full-scale template on page 32. Dual installations without a filler strip can only be accomplished using two units with opposite hinges as shown in illustration A below. The dual installations shown in illustrations B and C require a filler strip. IMPORTANT NOTE: For the application shown in illustration A, a dual installation accessory kit is required. Refer to page 27 for information on dual installation kits. WITHOUT STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT FILLER STRIP FILLER WITHOUT FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED Illus. A Illus. B 23 kg 12 kg Illus. C WITHOUT STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT WITHOUT FILLER STRIP FILLER FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED 16 mm Built-In Refrigeration 22 Dual Installation STANDARD INSTALLATION TOP VIEW 620 mm minimum OPENING DEPTH TWO UNITS WITH 19 mm PANEL 620 mm minimum OPENING DEPTH 2127 mm OPENING HEIGHT SIDE VIEW A OPENING WIDTH FRONT VIEW Opening Widths A IMPORTANT NOTE: A dual installation kit will be required Two 762 mm Models 1518 mm for this installation. 762 mm and 914 mm Models 1670 mm Stainless steel models are ready to install out of the box. Two 914 mm Models 1822 mm Built-In Refrigeration 23 subzero.com/specs Dual Installation FLUSH INSET APPLICATION Dual Installation Panel Requirements Installing two built-in models side by side in a flush inset application will require adjustments to the dimensions of your finished rough opening, panel sizes and panel offsets. It will also require a dual installation kit, available through your authorized Sub-Zero dealer. MAX WEIGHT PER PANEL All Models Dual Wide Grille Panel MIN PANEL THICKNESS Flush Inset Panels Dual installations without a filler strip can only be accomplished using two units with opposite hinges as shown in illustration A below. The dual installations shown in illustrations B and C require a filler strip. Refer to the full-scale template on page 33. Illustration A is the only application that will accommodate the dual wide grille. IMPORTANT NOTE: The application shown in illustration A can only be achieved by installing dual flush inset panels. Failure to install dual flush inset panels will cause the handle side of the panels to collide when closing. In this application a dual installation accessory kit is also required. WITHOUT FILLER WITHOUT STRIP FILLER STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT FILLER STRIP REQUIRED FILLER STRIP REQUIRED Dual flush inset panels and dual installation kits are avail able through your authorized Sub-Zero dealer. Refer to pages 25–26 for dual flush inset panel specifications and page 27 for information on dual installation kits. WITHOUT FILLER WITHOUT STRIP FILLER STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT FILLER STRIP REQUIRED FILLER STRIP REQUIRED Illus. A Illus. B Illus. C 23 kg 12 kg 16 mm Built-In Refrigeration 24 620 mm 675 minimum mm minimum OPENING FLUSH INSET DEPTH Dual Installation 76 mm typical 56 mm TOP VIEW 32 mm 620 mm 675 mm minimum minimum DEPTH TO CLEAT 32 mm TWO UNITS WITH 19 mm PANEL 620 mm 675 minimum mm minimum OPENING FLUSH INSET DEPTH CLEAT TOP VIEW CLEAT DEPTH TO CLEAT 76 mm typical DETAIL A 56 mm 56 mm 6 mm CLEAT DEPTH TO CLEAT FLUSH INSET INSTALLATION FLUSH INSET DEPTH TOP VIEW 32 mm CLEAT 620 mm minimum DEPTH TO CLEAT 675 mm minimum Detail A 56 mm FLUSH INSET DEPTH 76 mm typical CLEAT 2127 mm HEIGHT TO CLEAT 2134 mm A 32 mm 32 mm WIDTH TO CLEAT B FLUSH INSET WIDTH FLUSH INSET HEIGHT SHADED AREA MUST BE FINISHED 102 mm 620 mm minimum OPENING DEPTH TO CLEAT 56 mm CLEAT 32 mm Detail B 76 mm typical 102 mm SHADED AREA MUST BE FINISHED 620 mm minimum DETAIL B SIDE VIEW Opening Widths FRONT VIEW A B Two 762 mm Models 1518 mm 1581 mm 762 mm and 914 mm Models 1670 mm 1734 mm Two 914 mm Models 1822 mm 1886 mm OPENING DEPTH TO CLEAT 56 mm 32 mm IMPORTANT NOTE: Dimensions assume a 19 mm panel thickness. A dual installation kit will be required for this installation. TOP VIEW Built-In Refrigeration TOP VIEW DOOR / DRAWER / GRILLE BACKER SPACER TOP VIEW TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE BACKER CABINETRY SPACER 25 CABINETRY subzero.com/specs DOOR DOORDOOR TOP VIEW DOOR TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE DOOR / DRAWER / GRILLE FLUSH INSET PANEL FLUSH INSET PANEL Dual Installation FLUSH INSET PANEL OFFSETS 8 mm 8 mm 13 BACKER SPACER 16 mmSPACER TOP VIEW 16 Doors (handle) Sides Grille Top Grille Bottom / Door Top Drawer Bottom DOOR 8 mm CABINETRY Do not exceed flush inset panel dimensions, as this DOOR could cause damage to panels and the Sub-Zero unit. DRAWER 8 mm DOOR 3DOOR mm 6 mm DOOR 3 8 mm 3 mm 13 16 mm DOOR 6 mm REVEAL 13 mm 8 mm CABINETRY 4 mm 3 mm 8 mm 13 mm 8 mm4 DRAWER 2 mm 8 mm mm DOOR SIDE VIEW 16 mm DRAWER 4 E Illus. mm 8 mm DOOR SIDE VIEW DRAWER 4 mm 13 8 mm 2 4 mm 8 mm mm SIDE VIEW SIDE VIEW 13 mm DOOR 13 m 8 mm 2 4 mm 8 mm mm DOOR 2 GRILLE mm 8 mm 3 SIDEmm VIEW SIDE VIEW 8 mm SIDE VIEW 13 DOOR Illus. D 8 mm DOOR 8 mm GRILLE 8 DOOR mm2 GRILLE mm4 8 mm mm DOOR GRILLE 3 mmVIEW SIDE 8 mm SIDE VIEW 8 mm REVEAL 13 mm 13 mm 2 mm 8 mm GRILLE Illus. B GRILLE 6 mm REVEAL Illus. A 3 mm 8 mm 3 mm 6 mm mm 13 mm 16 mm DRAWER 8 mm mm TOP VIEW REVEAL REVEAL Illus. C A B C D E F DUAL TRIM DOOR 6 mm FLUSH INSET PANEL Illus. Doors (hinge) / Drawer / Grille Sides 6 mm mm GRILLE SIDE VIEW Door Bottom / Drawer Top 13 16 SPACER mm GRILLE OVER-AND-UNDER 8 mm DOOR DOOR 3 mm TOP VIEWREVEAL mm CABINETRY 8 Illustrations A–F provide panel offsets and reveals for all mm CABINETRY CABINETRY built-in models in a flush inset application. Refer to the 13 mm chart below for reference to the illustrations relating to your specific model. All reveals are 13 mm unless other3 wise specified. mm SIDE VIEW GRILLE GRILLE For additional information on model-specific panel reveals, visit the specification library section of our website, subzerotrade.com. 16 8 mm 3 DOOR mm mm 8 mm 13 mm BACKER CABINETRY IMPORTANT NOTE: If a filler strip is not used, dual installations can only be accomplished using two units with opposite hinges. mm CABINETRY DOOR / DRAWER / GRILLE FLUSH INSET PANEL INSET PANEL When installing two built-in models side by side inFLUSH a flush inset application, you must decrease the width of the 8 mm decorative flush inset panels by 13 mm. Adjustments to the panel offsets will also need to be made. These adjustments are needed to achieve a proper fit and to ensure the panels do not collide when closing. Panel dimensions in the chart below have been adjusted to reflect the decrease in panel dimensions. Panel Offsets 13 mm BACKER CABINETRY DOOR / DRAWER 2 mm 8 mm DOOR / DRAWER SIDE VIEW 2 mm 16 mm DOOR / DRAWER 8 mm 4 2 mm 8 mm mm SIDE VIEW SIDE VIEW 16 mm 8 mm 42 mm mm 8 mm SIDE VIEW 16 8 mm DOOR / DRAWER 2 mm SIDE VIEW 8 DOOR / mm DRAWER 8 mm 8 mm m Illus. F mm SIDE VIEW 2 mm SIDE VIEW m 8 mm 4 mm 8 mm SIDE VIEW SIDE VIEW m Built-In Refrigeration 26 Dual Installation—Flush Inset Panels H H H A H A H A A H A H W H W ICBBI-30U / ICBBI-36U ICBBI-30U ICBBI-36U H REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel HFREEZER Flush Inset Panel Spacer Panel Backer Panel A B GRILLE Flush Inset Panel Spacer Panel Backer Panel W 775 mm 740 mm 756 mm W 775 mm 740 mm 756 mm H 1273 mm 1253 mm 1268 mm H 483 mm 459 mm 475 mm WH 775 mm 740 mm 756 mm 235 mm 211 mm 227 mm REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel W 927 mm 892 mm 908 mm FREEZER Flush Inset Panel Spacer Panel Backer Panel W 927 mm 892 mm 908 mm GRILLE Flush Inset Panel Spacer Panel Backer Panel W 927 mm 892 mm 908 mm H 1273 mm 1253 mm 1268 mm H 483 mm 459 mm 475 mm H 235 mm 211 mm 227 mm W Grille panel dimensions listed are for a standard 2134 mm finished height. For a 2108 mm finished height, subtract 25 mm from grille panel height dimensions. For a 2235 mm finished height, add 102 mm to height dimensions. Width dimensions do not vary. For dual wide grilles, refer to page 27. Built-In Refrigeration 27 subzero.com/specs Dual Installation Kit INSTALLATION WITH DUAL WIDE GRILLE INSTALLATION WITH INDIVIDUAL GRILLES This kit will replace the existing grilles that ship with the units and span the entire width of both units. The kit includes a 6 mm center trim strip (required for proper installation of the dual wide grille), heater, dual kickplate and mounting hardware. Dual wide grilles are available for all built-in models and design applications. The overlay dual installation kit with grille will accept overlay and dual flush inset panels. For dual wide grille panel dimensions, refer to the panel specifications below for your design application. Grille panel dimensions listed are for a standard 2134 mm finished height. This kit is available for those who choose to utilize the individual grilles that ship with each unit. The kit includes a 6 mm filler strip (which fills the reveal between the units and grilles), heater and mounting hardware. This dual installation kit is not required if a custom filler strip is used. The filler strip should be a minimum of 51 mm wide. Refer to the full-scale template on page 32 for more information. Dual Wide Grille—Overlay TWO 762 mm MODELS Overlay Panel Spacer Panel Backer Panel 762 mm AND 914 mm MODELS Overlay Panel Spacer Panel Backer Panel TWO 914 mm MODELS Overlay Panel Spacer Panel Backer Panel W 1530 mm 1508 mm 1524 mm W 1683 mm 1661 mm 1676 mm W 1835 mm 1813 mm 1829 mm H 235 mm 211 mm 227 mm H 235 mm 211 mm 227 mm H 235 mm 211 mm 227 mm Dual Wide Grille—Flush Inset TWO 762 mm MODELS Flush Inset Panel Spacer Panel Backer Panel 762 mm AND 914 mm MODELS Flush Inset Panel Spacer Panel Backer Panel TWO 914 mm MODELS Flush Inset Panel Spacer Panel Backer Panel W 1556 mm 1508 mm 1524 mm W 1708 mm 1661 mm 1676 mm W 1861 mm 1813 mm 1829 mm H 235 mm 211 mm 227 mm H 235 mm 211 mm 227 mm H 235 mm 211 mm 227 mm Built-In Refrigeration 28 Accessories These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero. com. • Flush inset front panels in stainless steel with handle options. • Side panels in stainless steel and white enamel. • Grilles for a 2108 mm or 2235 mm finished height. STANDARD HANDLES Refer to the chart below for standard handle lengths and the stud spacing of tubular and pro handles used on built-in models. Standard Handles Tubular Handle Pro Handle 1622 mm 1146 mm 1114 mm 1114 mm ICBBI-30U AND ICBBI-36U DOOR • Tubular and pro handles to match the style of Wolf ovens and ranges. Tubular Handle Pro Handle • Dual installation kits with and without dual wide grille. Tubular Handle Pro Handle • Retrofit kits for use with 600 series panels. Length Stud Spacing FULL-HEIGHT DOOR 1124 mm 952 mm 921 mm 921 mm ICBBI-30U DRAWER 633 mm 447 mm 414 mm 414 mm ICBBI-36U DRAWER Tubular Handle Pro Handle 770 mm 597 mm 567 mm 567 mm Built-In Refrigeration 29 subzero.com/specs Overlay Panel Thickness FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 16 mm thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. DEPTH OF TUBULAR AND PRO HANDLES 51 mm 25 mm 76 mm 32 mm PANEL 25 mm PANEL 19 mm PANEL 3 mm SPACER PANEL 6 mm BACKER PANEL DOOR PANEL THICKNESS OVERLAY AND FLUSH INSET APPLICATIONS Built-In Refrigeration 30 Overlay Application FULL-SCALE TEMPLATE 606 mm OVERALL WIDTH OF UNIT TO REAR OF UNIT 0 mm 6 mm 13 mm 19 mm 25 mm 32 mm 38 mm 44 mm 51 mm 57 mm 63 mm 70 mm 76 mm 83 mm 89 mm 25 mm THICK PANEL 19 mm THICK OVERLAY PANEL (TYPICAL) 6 mm BACKER PANEL DOOR OPENING 90° TOP VIEW 0 mm 25 mm SCALE Built-In Refrigeration 31 subzero.com/specs Flush Inset Application FULL-SCALE TEMPLATE 610 mm TO BACK WALL For panels thicker than 19 mm, a 90° door stop may be required to prevent interference with adjacent cabinets. 32 mm 56 mm ASSUMES 19 mm FLUSH INSET PANEL THICKNESS 25 mm THICK PANEL 19 mm THICK FLUSH INSET PANEL (TYPICAL) 6 mm BACKER PANEL 0 mm DOOR OPENING 110° TOP VIEW 25 mm SCALE Built-In Refrigeration 32 FILLER STRIP 32 mm APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE DOOR OPEN 110° Dual Installation—Standard FULL-SCALE TEMPLATE Typical overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Depending on panel thickness, a 90° door stop may be required. 0 mm STANDARD TOP VIEW 25 mm SCALE DOOR CLOSED Built-In Refrigeration 33 subzero.com/specs FILLER STRIP 38 mm 13 mm PROFILE OF 19 mm FLUSH INSET PANEL AND TUBULAR HANDLE Dual Installation—Flush Inset FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maximum 110° door opening. Depending on panel thickness, a 90° door stop may be required. 0 mm FLUSH INSET TOP VIEW 25 mm SCALE DOOR CLOSED DOOR OPEN 110° PRO 48 Refrigeration 34 PRO 48 Refrigeration. Freshness finds unmistakable expression in the Sub-Zero PRO 48. A 363 kg monument to food preservation—equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel. The PRO 48 is available with or without a glass door and may be either built in or freestanding. PRO 48 MODELS 1219 mm KEY FEATURES 1219 mm 1219 mm 1219 mm • Can be used freestanding or installed as a standard or flush built-in application. • Handles coordinate with handles of Wolf ranges. • Stainless steel interior as well as exterior. 2134 mm 2134 mm 2134 mm 2134 mm • Dual refrigeration system enhanced with triple evaporators allow independent control of storage conditions in refrigerator cabinet and drawer compartments. • Exterior temperature display. • Flip-up grille provides easy access for quick routine maintenance. ICB648PRO ICB648PROG • Star-K certified. PRO 48 Refrigeration 35 subzero.com/specs PRO 48 Models OVERALL DIMENSIONS 1219 mm 657 mm 2134 mm 1070 mm 775 mm 102 mm HEIGHT DIMENSIONS ± 13 mm 767 mm 606 mm 368 mm 533 mm SPECIFICATIONS 781 mm 60 mm MODELS ICB648PRO AND ICB648PROG Capacity / Weight INTERIOR CAPACITY R (L) F (L) ICB648PRO and ICB648PROG 520 332 SHIPPING WEIGHT KG ICB648PRO ICB648PROG 390 397 PRO 48 Refrigeration 36 PRO 48 Models STANDARD AND FLUSH BUILT-IN INSTALLATIONS TOP VIEW OPENING DEPTH OPENING DEPTH OPENING HEIGHT SIDE VIEW Opening Dimensions Opening Width OPENING WIDTH FRONT VIEW Standard Flush 1206 mm 1219 mm Opening Height 2127 mm 2137 mm Opening Depth 620 mm min 670 mm min IMPORTANT NOTE: For standard built-in installations, the face frame of the unit will extend 51 mm beyond cabinetry. In flush built-in installations, the front of the face frame will be flush with surrounding cabinetry. PRO 48 Refrigeration 37 subzero.com/specs Planning Information PRO 48 models can be used freestanding or installed as a standard or flush built-in application. For standard built-in installations, the face frame of the unit will extend 51 mm beyond cabinetry. In flush built-in installations, the front of the face frame will be flush with surrounding cabinetry. ELECTRICAL REQUIREMENTS International models from the factory designed without a transformer require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device. For Pro 48 models the electrical supply should be either in the cabinet above the refrigerator a MINIMUM OF 2200mm ABOVE THE FLOOR or in the cabinet alongside. If freestanding then locate the power point as per the diagram below. A separate circuit, servicing only this appliance, is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Electrical Requirements PRO 48 models come with an automatic ice maker. a pressure limiting valve and 5 meters of flexible 6mm pipe with fittings is included in the refrigerator carton. Connect the pressure limiting valve close to the water tap, CHECKING THE WATER FLOW IS IN THE RIGHT DIRECTION. Ensure water connection is ½” BSP male threaded outlet. Tape the 6mm water line to the wall and floor to ensure it isn’t squashed when the refrigerator is pushed into the cavity. Locate the water tap either in the cabinet above a minimum of 2200mm from the floor, or in the cabinet alongside. The water line must not interfere with installation of the anti-tip brackets. IMPORTANT NOTE: A reverse osmosis system can be used provided there is constant water pressure of 2.1 bar to 6.9 bar supplied to the unit at all times. 1. Plumbing Requirements Power Supply 220-240 V AC, 50/60 Hz Circuit Breaker 10 amp Receptacle PLUMBING REQUIREMENTS 3-prong grounding-type Water Supply Line Water Pressure pressure limiting valve 6mm flexi hose & tape to wall 2.1–6.9 bar Water Line for Connection 5m FRONT VIEW 1. 1. 6mm plastic line 178 mm 2,200 mm FROM FLOOR pressure limiting valve 6mm flexi hose & tape to wall 2. 2. Pro 48. Alternative location of power & water supply depending on ease of access. pressure limiting valve 6mm flexi hose & tape to wall 1. Pro 48. Water supply above fridge. Location of 6mm flexible hose. Tape to wall and floor with pressure limiting valve next to tap. pressure limiting valve 6mm flexi hose & tape to wall 2. Pro 48. Water supply beside fridge. Location of 6mm flexible hose. Tape to wall and floor with pressure limiting valve next to tap. E 152 mm 1918 mm FROM FLOOR Freestanding location of power supply. PRO 48 Refrigeration Accessories These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. • Freestanding kit, which contains two stainless steel side panels and top lid. • Stainless steel side panel. • Refrigerator drawer dividers for compartmentalized storage. • Stainless steel slide-out refrigerator bin. • Dozen egg container. • 90° door stop. 38 Integrated Refrigeration 39 subzero.com/specs Integrated Refrigeration. With custom cabinet fronts and hardware, Sub-Zero invented integrated drawers and tall units that disappear into the decor. Integrated units fit flush with other cabinets, making integrated refrigeration as practical and beautiful in the master suite, bar or theatre room as in the kitchen. INTEGRATED MODELS KEY FEATURES 686 mm 686 mm 686 mm • Custom cabinet fronts and hardware allow for 914 mm686 mm 914 mm infinite design options. 686 mm 686 mm • Point-of-use refrigeration that can be placed anywhere in the home. 686 mm 2032 mm 686 mm 6 m 876 mm 2032 686 mmmm 2032 mm 876 mm 2032 686 mmmm 686 mm 876 mm 2032 mm 876 mm 2032 2032 2032 686 mm • Dual refrigeration; two compressors preserve mm mm mm food’s goodness in self-contained compartments. 876 mm Energy efficient. • • Drawer model is Star-K certified. ICB700TR 686 mm 32 m ICB700TCI 914 mm686 mm 2032 686 mmmm 2032 mm 686 mm 914 mm 2032 mm 686 mm 876 mm 876 mm ICB736TR ICB736TCI 686 mm 2032 mm 686 mm 876 mm ICB700BR 686 mm 2032 mm 686 mm 876 mm 2032 mm Integrated Refrigeration 40 Overall Dimensions 686 mm TALL MODELS 914 mm TALL MODELS 686 mm 610 mm 914 mm 610 mm 356 mm 356 mm 33 mm 21 mm 1976 mm 1995 mm 2032 mm 2032 mm TO TOP OF OPENNG 10 mm 13 mm 13 mm 337 mm 876 mm 260 mm 337 mm 876 mm 260 mm 518 mm 248 mm HEIGHT DIMENSIONS ± 13 TO TOP OF OPENNG 10 mm 518 mm 102 mm mm 248 mm HEIGHT DIMENSIONS ± 13 610 mm 610 mm 178 mm 117 mm 495 mm 102 mm mm 648 mm 495 mm DIMENSIONS WILL VARY WITH PANEL THICKNESS MODELS ICB700TR AND ICB700TCI DIMENSIONS WILL VARY WITH PANEL THICKNESS MODELS ICB736TR AND ICB736TCI Overall dimensions do not include panels or handles. 876 mm Integrated Refrigeration 41 subzero.com/specs Overall Dimensions Capacity and Weight DRAWER MODELS Interior Capacity 10 mm 686 mm 610 mm R (L) F (L) 439 288 143 590 378 200 686 mm TALL MODELS ICB700TR ICB700TCI 914 mm TALL MODELS 13 mm ICB736TR ICB736TCI 337 mm 876 mm 686 mm DRAWER MODEL ICB700BR 260 mm 518 mm 248 mm HEIGHT DIMENSIONS ± 13 mm 610 mm 495 mm 657 mm DIMENSIONS WILL VARY WITH PANEL THICKNESS MODEL ICB700BR 102 mm 149 Shipping Weight kg ICB700TR and ICB700TCI 163 ICB736TR and ICB736TCI 218 ICB700BR 86 Integrated Refrigeration 42 Opening Dimensions INTEGRATED MODELS IMPORTANT NOTE: The depth of each integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 645 mm. TOP VIEW 645 mm minimum OPENING DEPTH 645 mm minimum OPENING DEPTH B OPENING HEIGHT SIDE VIEW A OPENING WIDTH FRONT VIEW Opening Dimensions A B ICB700TR, ICB700TCI 686 mm 2032 mm ICB736TR, ICB736TCI 914 mm 2032 mm ICB700BR 686 mm 876 mm Integrated Refrigeration 43 subzero.com/specs Electrical Requirements International models from the factory require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. 1. 1. The electrical supply should be easily accessible either in the cabinet above the refrigerator a MINIMUM OF 2200MM ABOVE THE FLOOR or in the cabinet along2,200 mm FROM side. A separate circuit, servicing only this appliance, is FLOOR required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. 2. pressure limiting valve 6mm flexi hose & tape to wall Electrical Requirements 1. 1. Power Supply 220-240 V AC, 50/60 Hz Circuit Breaker 2,200 mm FROM FLOOR pressure limiting valve 6mm flexi hose & tape to wall 3-prong grounding-type pressure limiting valve 6mm flexi hose & tape to wall 2. 2. Integrated. Tall models. Alternative location of power and water supply depending on ease of access. 10 amp Receptacle Integrated. Under bench model. Location of power. pressure limiting valve 6mm flexi hose & tape to wall 2. Integrated Refrigeration 44 Plumbing Requirements For integrated models with an automatic ice maker, a pressure limiting valve and 5 meters of flexible 6mm pipe with fittings is included in the refrigerator carton. Connect the pressure limiting valve close to the water tap, CHECKING THE WATER FLOW IS IN THE RIGHT DIRECTION. Ensure water connection is ½” BSP male threaded outlet. Tape the 6mm water line to the wall and floor to ensure it isn’t squashed when the refrigerator is pushed into the cavity. Locate the water tap either in the cabinet above a minimum of 2200mm from the floor, or in the cabinet alongside. Do not use self‑piercing valves. 1. IMPORTANT NOTE: An in-line filter is required 1.when water conditions have a high sediment content. The ice maker operates on constant water pressure between 1.4 bar and 6.9 bar. 2,200 mm FROM pressure limiting valve IMPORTANT NOTE: FLOOR In some cases, a reverse osmosis 6mm flexi hose & tape to wall water filter system may not be able to maintain the minimum pressure consistently. 2. Plumbing Requirements 1. Water Supply Line Water Pressure Water Line for Connection pressure limiting valve 6mm flexi hose & tape to wall pressure limiting valve 6mm flexi hose & tape to wall 2. 1. Integrated. Water supply above fridge. Location of 6mm flexible hose. Tape to wall and floor with pressure limiting valve next to tap. pressure limiting valve 6mm flexi hose & tape to wall 2. 2. Integrated. Water supply beside fridge. Location of 6mm flexible hose. Tape to wall and floor with pressure limiting valve next to tap. 6mm plastic line 1.4–6.9 bar 5m Integrated Refrigeration 45 subzero.com/specs Cabinetry Applications FRAMELESS CABINETRY 679 mm 908 mm PANEL WIDTH PANEL WIDTH A A 1153 mm 1153 mm 2029 mm 2029 mm A A 345 mm 345 mm A 876 mm A 424 mm 424 mm 102 mm 102mm 914 mm 686 mm FINISHED OPENING ALL REVEALS (A) ARE 3 FINISHED OPENING mm. 686 mm MODELS 914 mm MODELS TALL AND DRAWER MODELS TALL MODELS Typical Panel Dimensions 686 mm MODELS Door Top Drawer Bottom Drawer 914 mm MODELS Door Top Drawer Bottom Drawer W 679 mm 679 mm 679 mm W 908 mm 908 mm 908 mm H 1153 mm 345 mm 424 mm H 1153 mm 345 mm 424 mm Panel dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible with adjustments to panel dimensions. Integrated Refrigeration 46 Cabinetry Applications DOOR PANEL HEIGHT TOE KICK CLEARANCE The height of the door panel can extend beyond the typical panel height, provided you do not exceed the panel weight limit. The illustration below shows how the panel may be extended and what you need to consider to finish the area behind the door panel. The toe kick clearance can vary with the height of the panel. You must keep a minimum space of 102 mm clear below the bottom edge of the panel for proper venting. In addition, any decorative base molding must be removable to clean the condenser and for service. IMPORTANT NOTE: The decorative valance used to finish the area behind the door panel must stay behind the front plane of the finished molding. 38 mm INTEGRATED UNIT (SIDE VIEW) DECORATIVE VALANCE CANNOT EXTEND BEYOND THE FRONT OF THE MOLDING 3 mm DOOR PANEL OVERALL HEIGHT 635 mm TO WALL DECORATIVE VALANCE HEIGHT OF PANEL KICKPLATE / GRILLE CAN BE ADJUSTED FORWARD KICKPLATE / GRILLE 3 mm REMOVABLE MOLDING MINIMUM HEIGHT BASE MOLDING MUST BE REMOVABLE HINGE 102 mm TO 229 mm TYPICAL HEIGHT OF DOOR PANEL 635 mm TO WALL FROM FLOOR INTEGRATED UNIT (SIDE VIEW) 67 mm TO 102 mm UPPER VALANCE KICKPLATE / GRILLE AREA TALL MODELS ALL INTEGRATED MODELS Integrated Refrigeration 47 subzero.com/specs Cabinetry Applications Integrated refrigeration is compatible with virtually any style and look of cabinetry. These models can be used with framed as well as frameless cabinetry. Because of the precise application and the look you may want to achieve, keep the following considerations in mind: The thickness of the front panels can vary. A minimum 16 mm thick panel is required, but the thickness can be increased provided the panel weight limit is not exceeded. IMPORTANT NOTE: The depth of each integrated model is 610 mm from the front of the unit to its back. You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You may have to move the unit back into drywall or bring the cabinets forward to achieve a flush fit. Reveals between panels can vary. A reveal of 3 mm is typical, but reveals can be increased to up to 6 mm. As reveals between cabinetry and the unit decrease, the potential exists for severe finger pinching while the door is closing. When 19 mm or thicker panels are used with a reveal of less than 6 mm, door panels may cause damage to the unit when the door is opened to the maximum 105°. Use the built-in 90° door stop. IMPORTANT NOTE: The inside edges of the rough opening as well as the sides and a portion of the backside of the decorative panels will need to be finished, as they will be exposed when the doors are open. D-style handles are recommended. For the cabinet door, handles must be located near the edge of the panel opposite the hinge, centered top to bottom. Locate handles in the top center area of the drawer panels. Illustrations on the following pages show typical applications of frameless and framed cabinetry. Also refer to the full-scale illustration at the end of this section for specifics on door openings. Panel Requirements TALL AND DRAWER MODELS MAX WEIGHT 686 mm Door Panel 686 mm Drawer Panel 914 mm Door Panel 914 mm Drawer Panel 18 kg 5 kg 24 kg 7 kg PANEL THICKNESS MINIMUM All Panels 16 mm INTEGRATED UNIT CABINET INTEGRATED CABINET UNIT Integrated PANEL DOOR Refrigeration 3 mm REVEAL 48 CABINET INTEGRATED UNIT DOOR PANEL FINISHED OPENING PANEL DOOR 3 mm REVEAL FINISHED Cabinetry Applications OPENING Dual Installations 3 mm FINISHED The illustrations below show typicalREVEAL applications of framed OPENING and frameless cabinetry. Refer to the full-scale templates INTEGRATED CABINET at the end of this section for UNITspecifics on door openings. DOOR CABINET 3 mm PANEL INTEGRATED UNIT REVEAL CABINET 3 mm REVEAL Typical Panel Dimensions 686 mm MODELS DOOR 3 mm REVEAL FINISHED OPENING Framed—full overlay. Door Top Drawer Bottom Drawer PANEL 914 mm MODELS Door Top Drawer Bottom Drawer FINISHED OPENING CABINET INTEGRATED UNIT INTEGRATED UNIT 3 mm 3 mm REVEAL PANEL CABINET FINISHED OPENING FINISHED OPENING DOOR Framed—beaded inset. DOOR 3 mm REVEAL PANEL UNIT FINISHED OPENING PANEL Frameless cabinetry. 3 mm REVEAL FINISHED OPENING CABINET INTEGRATED UNIT DOOR PANEL COLDER WARMER REFRIGERATOR COLDER ICE ALARM ON/OFF UNIT CABINET 3 mm REVEAL DOOR PANEL 3 mm REVEAL FINISHED OPENING H 1153 mm 345 mm 424 mm IMPORTANT NOTE: If a 686 mm unit is installed next to a 914 mm tall unit, the decorative front panels will align, however, the face frames will not. This is only apparent when both doors are open at the same time. Due to a more robust hinge on 914 mm units, the face frame was reconfigured to maintain a consistent overall panel height. Refer to the illustration below. PANEL REVEAL W 910 mm 910 mm 910 mm H 1153 mm 345 mm 424 mm A dual installation kit is required for installations with 51 mm or less space between the units. Dual installation kits are available through your authorized Sub-Zero dealer. DOOR DOOR W 681 mm 681 mm 681 mm Framed—standard overlay. UNIT CABINET CABINET INTEGRATED UNIT FINISHED OPENING PANEL DOOR Two integrated units may be placed side by side in a dual installation. Depending on the models specified, opening widths will be 1372 mm, 1600 mm or 1829 mm. Panel width dimensions will vary slightly from single installations. Refer to the chart below for typical panel dimensions. The dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible with adjustments to panel dimensions. FINISHED OPENING Face frame alignment. WARMER Integrated Refrigeration 49 subzero.com/specs Accessories These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero. com. • Stainless steel front panels with handles. • Tubular and pro handles to match the style of Wolf ovens and ranges. • Crisper drawer with shelf assembly, deli drawer with shelf and crisper cover with lid for certain models. • Dual installation kit. • Harness kit for Star-K compliance. STANDARD HANDLES Refer to the chart below for standard handle lengths and the stud spacing of tubular and pro handles used on integrated models. Standard Handles Length Stud Spacing DOOR Tubular Handle Pro Handle 1046 mm 1006 mm 845 mm 973 mm 686 mm MODEL DRAWERS Tubular Handle Pro Handle 614 mm 533 mm 413 mm 500 mm 914 mm MODEL DRAWERS Tubular Handle Pro Handle 843 mm 762 mm 641 mm 730 mm Integrated Refrigeration 50 INTEGRATED INTEGRATED DOOR DOOR MAXIMUM 105° OPENING MAXIMUM 105° OPENING Maximum Door Opening FULL-SCALE TEMPLATE If the panel is thicker than 19 mm, use the built-in 90° door stop to prevent damage to the panel and face frame at the maximum door opening. 105° OPENING LINE OF LINE OF INTERFERENCE INTERFERENCE TOP VIEW—1/4 SCALE LINE OF INTERFERENCE LINE OF INTERFERENCE MAXIMUM 105° OPENING MAXIMUM 105° OPENING 3 mm MINIMUM 3 mmREVEAL MINIMUM REVEAL FRAMED PANEL FRAMED PANEL 19 mm 19 mm MOUNTINGMOUNTING BRACKET BRACKET INTEGRATED DOOR CLOSED INTEGRATED DOOR CLOSED LINE OF INTERFERENCE LINE OF INTERFERENCE SIDE MOLDING SIDE AND MOLDING AND INSTALLATION HARDWARE INSTALLATION HARDWARE 0 mm DOOR CLOSED TOP VIEW—FULL-SCALE 25 mm SCALE Wine Storage 51 subzero.com/specs Wine Storage. Wine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced shelves, soft lighting, custom cabinetry if desired—Sub-Zero helps make a wine collection an element of beauty in the home. WINE STORAGE MODELS 686 mm 606 mm 864 mm 864 mm ICB424G 384 mm 865 mm 606 mm 865 mm 864868 mmmm 384 mm 865 mm 762 mm 762 mm 762 mm 762 mm762 mm 686 mm 686 mm 686 686 mm mm686 686mm mm 686 mm 686 mm686 mm 2032 2032 2032 20322032 2032 2032 mm mm mm mm mm 606616 mmmm606 616 mm606 616 mmmm616 mmmm mm 616 mm mm 864 868 864 mm mm mm 384 mm 865 mm 868 mm 868 mm 2134 2032 mm mm 2134 mm 2134 mm 2134 mm 868 mm ICB424FSG 384 mm 2032 2134 2032 mm mmmm 384 mm ICB427G ICB427RG ICBWS-30 865 mm KEY FEATURES • Integrated, overlay, flush inset and stainless steel design options. • Two independent storage zones maintain temperature, humidity and UV protection. • Full-view glass door standard on all models. • Cherrywood shelf fronts display the wine beautifully. • Freestanding model ICB424FSG does not require panels or surrounding cabinetry. • Rust-proof metal shelves accommodate 750 ml bottles, half-bottles and magnums. • Discreet interior lighting with illuminated display shelf. Wine Storage 52 Overall Dimensions UNDERCOUNTER WINE STORAGE 606 mm 610 mm 864 mm 102 mm 645 mm 60 mm MODEL ICB424G Overall dimensions are based on stainless steel panels and handles. Wine Storage 53 subzero.com/specs Overall Dimensions FULL-SIZE WINE STORAGE 686 mm 686 mm 610 mm 610 mm 356 mm 356 mm 21 mm 21 mm 1995 mm 1995 mm 2032 mm 2032 mm OPENING HEIGHT 13 mm 518 mm 227 mm HEIGHT DIMENSIONS ± 13 102 mm mm OPENING HEIGHT 10 mm 337 mm 876 mm 260 mm 248 mm HEIGHT DIMENSIONS ± 13 102 mm mm 610 mm 610 mm 117 mm 117 mm 648 mm 495 mm 648 mm DIMENSIONS WILL VARY WITH PANEL THICKNESS DIMENSIONS WILL VARY WITH PANEL THICKNESS MODEL ICB427G MODEL ICB427RG WITH REFRIGERATOR DRAWERS Overall dimensions do not include panels or handles. Wine Storage 54 Overall Dimensions Capacity and Weight FULL-SIZE WINE STORAGE Storage Capacity 762 mm 610 mm Bottles (750 ml) R (L) ICB424G46 ICB427G132 ICB427RG ICBWS-30 78 150 147 2134 mm 1873 mm HEIGHT DIMENSIONS ± 13 mm 102 mm 606 mm 606 mm 432 mm 796 mm 60 mm MODEL ICBWS-30 Overall dimensions are based on the stainless steel model. For flush inset applications, add 13 mm to door clearance dimensions. ICB424G 88 ICB424FSG 100 ICB427G 179 ICB427RG 186 ICBWS-30 202 Wine Storage 55 subzero.com/specs Opening Dimensions UNDERCOUNTER WINE STORAGE FULL-SIZE WINE STORAGE TOP VIEW TOP VIEW 645 mm 620 mm minimum minimum OPENING DEPTH OPENING DEPTH 620 mm minimum OPENING DEPTH 876 mm OPENING HEIGHT 610 mm OPENING WIDTH 645 mm minimum SIDE VIEW FRONT VIEW OPENING DEPTH 2032 mm OPENING HEIGHT 686 mm OPENING WIDTH MODEL ICB424G SIDE VIEW FRONT VIEW MODELS ICB427G AND ICB427RG IMPORTANT NOTE: The depth of each integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 645 mm. Wine Storage 56 Opening Dimensions Planning Information FULL-SIZE WINE STORAGE All wine storage models must be installed so that the door can open a minimum of 90° or you will have problems pulling the wine shelves out. For corner installations, you need to allow for a minimum 76 mm filler so the door can open to 90°. If you are using larger-handle hardware, you will also need to take that into account. Refer to door clearance specifications. TOP VIEW 620 mm minimum OPENING DEPTH For a maximum 90° door opening, use the door stop built into the hinge system of model ICB427G. A 90° door stop is shipped with model ICBWS-30. If you will be connecting the unit to a home security system, you must allow a minimum of 914 mm of the system’s wiring to be routed in the electrical area designated for your model. 620 mm minimum OPENING DEPTH SIDE VIEW MODEL ICBWS-30 2127 mm OPENING HEIGHT 746 mm OPENING WIDTH FRONT VIEW Wine Storage 57 subzero.com/specs Planning Information DUAL INSTALLATIONS 1. If you are installing a wine storage unit next to an existing Sub-Zero unit, you may have to allow for a filler strip. If you are installing a model ICB427G or ICB427RG next 2,200 mm FROM to an existing integrated unit, with 51 mm or less between FLOOR the units, an optional heater kit will need to be installed to prevent moisture from forming between the units. These optional heater kits are available through your authorized 2. Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. ELECTRICAL REQUIREMENTS International models from the factory require a 220-240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. Electrical Requirements 1. The electrical supply should be either in the cabinet above the refrigerator a MINIMUM OF 2200MM ABOVE THE FLOOR or in the cabinet alongside. A separate circuit, servicing only this appliance, is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Receptacle 1. Power Supply Circuit Breaker 2,200 mm FROM FLOOR 2. 1. 2,200 mm FROM FLOOR 2. Built in Tall Models. Alternative location of power and water supply depending on ease of access. 2,200 mm FROM FLOOR 2. Integrated Tall Models. Alternative location of power and water supply depending on ease of access. Under Bench Model. Location of power. 1. 2,200 mm FROM FLOOR 2. 220-240 V AC, 50/60 Hz 10 amp 3-prong grounding-type Wine Storage 58 Door Panels Overlay Panels Unless you are installing a stainless steel model, you will need to provide a frame for the glass door. If you order a stainless steel unit, models ICB424G, ICB424FSG and ICBWS-30 will be shipped with their panels and hardware installed. For models ICB427G and ICB427RG, optional stainless steel panels or custom panels will need to be installed. MODEL ICB424G The glass door is designed to be exposed to room air circulation. Decorative overlays on the glass should be kept to a minimum. Also, rails and stiles can be increased in size but should not exceed the cabinet manufacturers’ standard width and cannot exceed the overall door panel dimensions listed in the charts. The back sides of rails and stiles that will be visible through the glass door will need to be finished. Also, the inside edges of the frames must be finished to match the front surface. The overlay panel applied to model ICB424G should not be confused with the built-in overlay panel application. The overlay panel will consist of just a frame and would be either the 16 mm or 19 mm thick panel you may be using. It is affixed directly to the door itself with screws through a series of predrilled holes in the door frame. A backer and spacer panel is not required. Model ICB424G can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit so that it extends 6 mm beyond the front surface of surrounding cabinetry. This will prevent interference between the door panel and adjoining cabinetry at the maximum 145° door swing. Refer to the full-scale template at the end of this section. Overlay Panels FREESTANDING MODEL ICB424FSG Model ICB424FSG does not require any panels or surrounding cabinetry. It has a beautiful stainless steel exterior that is designed to be used in a freestanding application. PANEL DIMENSIONS ICB424G W H 603 mm 764 mm MIN WIDTH Stiles and Rails 57 mm MAX PANEL WEIGHT Door Frame 5 kg MIN PANEL THICKNESS All Panels 16 mm Wine Storage 59 subzero.com/specs Integrated Panels MODELS ICB427G AND ICB427RG The integrated full panels or frame panels for glass doors for these models will follow some of the identical planning processes used with the integrated line. The installation of the door panels is completely different, however. Rather than using the mounting hardware we used with the integrated line, door panels for both models ICB427G and ICB427RG will be applied with screws applied through our door. The drawer panels for the model ICB427RG will be applied using the integrated technique of mounting brackets. IMPORTANT NOTE: The depth of models ICB427G and ICB427RG is 610 mm from the front of the unit to its back. You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You may have to move the unit back into the drywall or bring the cabinets forward. Refer to the integrated section. Panel dimensions listed in the chart assume the models finish off at 2032 mm in height overall and have a 102 mm toe kick for the model ICB427G. If you finish off at 2134 mm, for instance, you must add an additional 102 mm to the finished height of the panel and 102 mm to the top rail. Likewise, if you allow for a 152 mm toe kick for the model ICB427G, you must subtract 51 mm from the bottom rail. The height of the door panel for models ICB427G and ICB427RG can extend beyond the typical panel height, provided you do not exceed the panel weight limit. Refer to specifications on page 46 of the integrated section. The toe kick area on model ICB427G cannot be larger than 152 mm, and on model ICB427RG, no larger than 229 mm. The toe kick area for either model cannot be less than 102 mm. If you are installing an optional lock kit on models ICB427G or ICB427RG, you may have to order door panels that exceed the 2032 mm finished height. Consult the lock kit installation instructions and see if your panels will allow for an adequate installation. These instructions are available on our website, subzero.com. Integrated Panels ICB427G Door ICB427RG Door Top Drawer Bottom Drawer W 679 mm W 679 mm 679 mm 679 mm H 1927 mm H 1153 mm 345 mm 424 mm Panel Requirements MIN WIDTH Stiles Top Rail Bottom Rail (ICB427G) Bottom Rail (ICB427RG) 57 mm 95 mm 203 mm 76 mm MAX PANEL WEIGHT Door Frame Drawer Panel (ICB427RG) 9 kg 5 kg MIN PANEL THICKNESS All Panels 16 mm A A A H H Wine Storage 60 A W W Model ICBWS-30 OVERLAY PANEL OVERLAY PANEL SPECIFICATIONS Overlay model ICBWS-30 can be used in an overlay or flush inset application. The specific application will affect panel sizes, opening dimensions and the installation. A A Overlay model ICBWS-30 will be shipped without handle hardware and with an overlay panel grille as standard equipment. Along with the door panel, you will need to provide a panel for the grille and hardware to complement your surrounding cabinetry. The overlay design allows the decorative panel to cover the door trim for a more seamless appearance. The most common way to achieve this look is to work with three panels—the decorative overlay panel, which is typically 19 mm, a 3 mm spacer panel and a 6 mm backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions. The illustrations below will give you a better idea of the panel construction and how it interacts with our frame. The size of the overlay panel is critical, it must fit over the door frame. H H H H A A W W ICBWS-30 Overlay DOOR Overlay Panel Spacer Panel Backer Panel W H 762 mm 740 mm 756 mm 1772 mm 1751 mm 1767 mm NOT APPLICABLE IN AUSTRALIA IMPORTANT NOTE: Do not cover the glass door with a solid panel. The window cut-out edges of the overlay, spacer and backer panels will need to be finished, as they will be exposed. GRILLE Overlay Panel Spacer Panel Backer Panel WINDOW Cut-Out W H 762 mm 740 mm 756 mm 235 mm 211 mm 227 mm W H 597 mm 1607 mm A Location 83 mm Overlay Panel Requirements MODEL ICBWS-30 Max Panel Weight Min Panel Thickness OVERLAY PANEL SPACER PANEL 34 kg 16 mm SPACER PANEL OVERLAY PANEL DOOR FRAME 8 mm min 3 mm 2 1/4" (57) Rail / Stile .10" (3) Spacer Panel Do not exceed overlay panel dimensions, as this could cause damage to panels and.10" the Sub-Zero unit. (3) Overlay Panel BACKER PANEL TRIM Grille panel dimensions listed are for a standard 2134 mm overall height of the unit. For a 2108 mm overall height, subtract 25 mm from grille panel height dimensions. For a 2235 mm overall height, add 102 mm to height dimensions. Width dimensions do not vary. BACKER PANEL GLASS 1/4" (6) Backer Panel 5/16" (8) min Door Frame 19 mm typical 6 3 mm mm Panel assembly cross section. Panel assembly rear view. 5/32" (4) 1/16" (2) Glass Door/ Grille Trim A A A H H Wine Storage 61 subzero.com/specs A W W Model ICBWS-30 FLUSH INSET PANEL FLUSH INSET PANEL SPECIFICATIONS Overlay model ICBWS-30 used in a flush inset application allows the decorative panel to cover the door trim for a seamless appearance. The most common way to achieve this look is to work with three panels—the decorative flush inset panel, which is typically 19 mm, a 3 mm spacer panel and a 6 mm backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions. The illustrations below will give you a better idea of the panel construction and how it interacts with our frame. The size of the flush inset panel is critical, it must fit over the door frame. IMPORTANT NOTE: Do not cover the glass door with a solid panel. The inside edges of the rough opening as well as the sides and a portion of the back side of the decorative panels will need to be finished, as they will be exposed when the doors are open. The window cut-out edges of the overlay, spacer and backer panels will also need to be finished. IMPORTANT NOTE: For flush inset panels thicker than 19 mm, a 90° door stop may be required to prevent interference with adjacent cabinets. A A H H H H A A W W ICBWS-30 Flush Inset DOOR Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel WINDOW Cut-Out W 787 mm 740 mm 756 mm H 1770 mm 1751 mm 1767 mm W 787 mm 740 mm 756 mm H 235 mm 211 mm 227 mm W 597 mm H 1581 mm Flush Inset Panel Requirements Location A 95 mm MODEL ICBWS-30 Max Panel Weight Min Panel Thickness FLUSH INSET PANEL SPACER PANEL 34 kg 16 mm SPACER PANEL FLUSH INSET PANEL Do not exceed flush inset panel dimensions, as this could cause damage to panels and the Sub-Zero unit. BACKER PANEL BACKER PANEL TRIM 14 mm 8 mm min Panel assembly cross section. Grille panel dimensions listed are for a standard 2134 mm overall height of the unit. For a 2108 mm overall height, subtract 25 mm from grille panel height dimensions. For a 2235 mm overall height, add 102 mm to height dimensions. Width dimensions do not vary. 19 mm typical 3 mm 6 mm Panel assembly rear view. Wine Storage 62 TOP VIEW TOP VIEW R / DRAWER / GRILLE ER ER DOOR CABINETRY Model ICBWS-30 SH INSET PANEL 8 mm FLUSH INSET PANEL DOOR TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE DUAL INSTALLATIONS 8 mm and reveals for Illustrations A–D provide panel offsets 13 3 mm mm BACKER CABINETRY model ICBWS-30 in a flush inset application. Refer to the 16 6 mm SPACER mm REVEAL chart below for reference to the illustrations. When two models ICBWS-30 or a model ICBWS-30 and DOOR DOOR built-in unit are installed side by side, a dual installation kit may be required. Contact your Sub‑Zero dealer for the proper components and installation instructions. For questions relative to the installation, contact your 8 mm Sub-Zero dealer. 3To mmobtain local dealer information, visit mm website, subzero.com. the find a showroom section of6our FLUSH INSET PANEL For additional information on panel reveals, visit the specimm fication library section of our website, 8subzerotrade.com. 13 16 mm mm Panel Offsets REVEAL Illus. MODEL ICBWS-30 Grille Top CABINETRY GRILLE OOR WER TOP VIEW Grille Bottom / Door Top Door Bottom 8 13 mm 3 mm 8 mm mm GRILLE DOOR DOOR TOP VIEW SIDE SPACER VIEW 13 mm 2 13 mm mm 8 mm DOOR 3 SIDEmm VIEW 8 mm DOOR 8 mm 3 mm BACKER CABINETRY 6 mm REVEAL GRILLE FLUSH INSET PANEL 8 mm 8 mm 3 mm 13 16 mm SIDE VIEW mm Illus. A 8 mm 2 mm TOP VIEW A custom filler strip can be used in between two units in an overlay or stainless steel design application. It is recommended that the filler strip 8 be at least 51 mm wide, mm GRILLE to prevent condensation between4 the units. Be sure to mm DOOR add the filler strip width to your rough opening width. 13 mm Dual installations without a filler strip can only be accomplished using two units with opposite hinges as shown in DOOR 2 illustration A below. The dual installations shown in illusmm 8 trations B and C require a filler mmstrip. 6 mm SIDE VIEW IMPORTANT NOTE: For the application shown in illustraREVEAL tion A, a dual installation accessory kit is required. Illus. B GRILLE 16 mm CABINETRY 4 mm Two overlay or stainless steel units may be placed side by side in a dual installation. Some dual standard installations will require a dual installation kit, available through your Sub‑Zero dealer. 4 mm CABINETRY DOOR / DRAWER / GRILLE DUAL STANDARD INSTALLATIONS A B C D Door / Grille Sides DOOR 8 mm SIDE VIEWGRILLE DOOR / DRAWER 8 mm 4 mm 13 mm 13 mm 2 mm 8 mm 3 mm SIDE VIEW 8 mm 8 mm SIDE VIEW 2 mm 16 mm SIDE VIEW Illus. D 8 mm 2 GRILLE mm DOOR DRAWER Illus. C DOOR / DRAWER WITHOUT STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRE WITHOUT FILLER STRIP FILLER WITHOUT FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED DOOR 4 mm 8 mm DOOR / DRAWER 8 mm 4 mm Illus. A Illus. B Illus. C 8 mm 13 mm 2 mm 8 mm 2 REQUIRED WITHOUT STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT WITHOUT FILLER STRIP FILLER FILLER STRIP REQUIRED FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRE SIDE VIEW SIDE VIEW SIDE VIEW mm A A A H H Wine Storage 63 subzero.com/specs A W W Model ICBWS-30 DUAL FLUSH INSET INSTALLATIONS DUAL FLUSH INSET PANEL SPECIFICATIONS Installing two models ICBWS-30 or a model ICBWS-30 and built‑in unit side by side in a flush inset application will require adjustments to the dimensions of your finished rough opening, panel sizes and panel offsets. It will also require a dual installation kit, available through your Sub‑Zero dealer. Dual installations without a filler strip can only be accomplished using two units with opposite hinges as shown in illustration A below. The dual installations shown in illustrations B and C require a filler strip. Illustration A is the only application that will accommodate the dual wide grille. IMPORTANT NOTE: The application shown in illustration A can only be achieved by installing dual flush inset panels. Failure to install dual flush inset panels will cause the handle side of the panels to collide when closing. In this application a dual installation accessory kit is also required. Dual flush inset panels and dual installation kits are available through your Sub‑Zero dealer. Refer to the illustration and chart for dual flush inset panel specifications. A A H H H H A A W W ICBWS-30 Dual Flush Inset DOOR Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel WINDOW Cut-Out W 775 mm 740 mm 756 mm H 1770 mm 1751 mm 1767 mm W H 775 mm 740 mm 756 mm 235 mm 211 mm 227 mm W 584 mm Location H 1581 mm A 95 mm WITHOUT STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT FILLER STRIP FILLER WITHOUT FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED Grille panel dimensions listed are for a standard 2134 mm overall height of the unit. For a 2108 mm overall height, subtract 25 mm from grille panel height dimensions. For a 2235 mm overall height, add 102 mm to height dimensions. Width dimensions do not vary. Illus. A Illus. B Illus. C WITHOUT STRIP FILLER STRIP FILLER STRIP REQUIRED FILLER STRIP REQUIRED WITHOUT WITHOUT FILLER STRIP FILLER FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED FILLER STRIP REQUIRED TOP VIEW Wine Storage TOP VIEW DOOR / DRAWER / GRILLE BACKER SPACER 64 DOOR TOP VIEW TOP VIEW 8 mm DUAL FLUSH INSET PANELS TOP VIEW TOP VIEW DOOR / DRAWER / GRILLE DOOR / DRAWER / GRILLE FLUSH INSET PANEL Model ICBWS-30 DOOR CABINETRY 13 16 mm mm 8 mm 3 mm BACKER SPACER BACKER CABINETRY SPACER When installing two models ICBWS-30 or a modelFLUSH INSET PANEL ICBWS-30 and built‑in unit side by side in a flush inset 8 mm application, you must decrease the width of the decorative flush inset panels by 13 mm. Adjustments to the panel offsets will also need to be made. These adjustments are needed to achieve a proper fit and to ensure the panels do not collide when closing. Panel dimensions in the chart below have been adjusted to reflect the decrease in panel CABINETRY dimensions. 8 mm 13 For additional information on panel reveals, visit the specification library section of our website, subzerotrade.com. 8 mm 13 mm CABINETRY 16 16 SPACER mm 8 mm 2 DOOR TOP VIEW 8 mm DOOR 3DOOR mm 6 mm DOOR 3 DOOR 6 mm REVEAL REVEAL FLUSH INSET PANEL 8 mm 8 mm 3 mm 13 mm 16 8 mm 3 mm 6 mm mm GRILLE Illus. A 4 mm 3 mm GRILLE 8 CABINETRY mm REVEAL Illus. B 13 mm CABINETRY DOOR 13 mm 6 mm REVEAL 8 mm 2 13 mm mm 8 mm 3 SIDEmm VIEW 8 mm 13 mm 8 mm GRILLE 8 mm 4GRILLE mm 4 mm 13 mm DOOR 13 m 8 mm 2 4 mm 8 mm mm DOOR 2 GRILLE mm 8 mm 3 SIDEmm VIEW SIDE VIEW 8 mm Illus. C DOOR / DRAWER Panel Offsets mm 8 mm mm DUAL TRIM mm GRILLE SIDE VIEW Do not exceed the flush inset decorative panel dimensions. Exceeding dimensions could cause damage to the panels and the Sub-Zero unit. DOOR DOOR TOP VIEW TOP VIEWREVEAL mm BACKER CABINETRY Illustrations A–E provide panel offsets and reveals for model ICBWS-30 in a flush inset application. Refer to the chart below for reference to the illustrations. All reveals are 13 mm unless otherwise specified. SIDE VIEW GRILLE DOOR DOOR / DRAWER / GRILLE FLUSH INSET PANEL 13 mm IMPORTANT NOTE: If a filler strip is not used, dual installations can only be accomplished using two units with 3 mm opposite hinges. GRILLE CABINETRY 6 mm SIDE VIEW 13 DOOR Illus. D 2 mm 8 mm SIDE VIEW SIDE VIEW Illus. DOOR MODEL ICBWS-30 Doors (hinge) / Grille Sides 16 mm Doors (handle) Sides Grille Top DRAWER 4 mm Grille Bottom / Door Top 8 mm Door Bottom DOOR A B C D E 8 mm 2 mm DOOR 16 mmSIDE VIEW SIDE VIEW DRAWER DRAWER 4 E Illus. mm 8 mm DOOR SIDE VIEW DRAWER 8 mm 8 mm DOOR / DRAWER DOOR / DRAWER 2 mm 2 mm 16 mm 8 mm 8 mm 42 mm mm 8 mm SIDE VIEW 16 mm SIDE VIEW DOOR / DRAWER 2 mm SIDE VIEW 8 mm m 8 mm 4 mm 8 mm SIDE VIEW SIDE VIEW m Wine Storage 65 subzero.com/specs Side Panels Handle Hardware MODEL ICBWS-30 For overlay and integrated models, handle hardware must be provided. Optional stainless steel tubular and pro handles are available through your authorized Sub-Zero dealer. When planning for side panels with the installation of the model ICBWS-30, you need to be aware of the space configuration to achieve a pleasing fit. Depending on the exact panel you are using, the height of the panel may vary. IMPORTANT NOTE: The use of side panels may change the width of your rough opening. When installing a model ICBWS-30 with a custom side panel, an accessory kit (7003407) is required. Stainless steel side panels are also available through your authorized Sub-Zero dealer. The side panel will need to be a minimum of 620 mm deep and 13 mm thick. Refer to the illustrations below for side panel dimensions. Routing will be necessary so that the side panel fits flush against the side of the unit. 620 mm minimum FRONT OF SIDE PANEL ROUT TO 3 25 mm 3 mm 13 mm mm 48 mm 2134 mm 25 mm MAIN FRAME Routing detail. 102 mm OPTIONAL TOE KICK CUT-OUT 48 mm 67 mm Side panel dimensions. SIDE PANEL ROUTING The door frame has numerous mounting holes on each side to accommodate handle hardware. Using the predrilled holes to attach the handle will provide the best alignment and strength. IMPORTANT NOTE: Refer to the full-scale template at the end of this section for a profile of the door frame and position of the glass. Do not drill through the glass. Wine Storage 66 Accessories Door Frame Profile These optional accessories are available through your authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero. com. FULL-SCALE TEMPLATE • Front panels in stainless steel with handle options. • Grilles for a 2108 mm or 2235 mm finished height for model ICBWS-30. • Side panels in stainless steel and white enamel for model ICBWS-30. The full-scale template below shows an example of the door frame profile for wine storage models and the relationship to the overlay panel (rails and stiles). Dimension A ICB424G ICB427G and ICB427RG ICBWS-30 25 mm 22 mm 24 mm • Tubular and pro handles to match the style of Wolf ovens and ranges. • Door lock kits. • Dual installation kits. • Harness kit for Star-K compliance. GLASS STANDARD HANDLES Refer to the chart below for standard handle lengths and the stud spacing of tubular and pro handles used on wine storage models. Standard Handles Length Stud Spacing ICB424G, ICB424FSG, ICB427RG DRAWERS Tubular Handle Pro Handle 614 mm 533 mm 413 mm 500 mm CABINET DOOR PROFILE CL A A 57 mm RAIL/STILE ICB427G AND ICB427RG DOOR Tubular Handle Pro Handle 1046 mm 1006 mm 845 mm 973 mm ICBWS-30 Tubular Handle Pro Handle 1622 mm 1147 mm 1114 mm 1114 mm DOOR FRAME PROFILE DOOR FRAME PROFILE MODEL ICB424G SHOWN Wine Storage 67 subzero.com/specs Wine Shelf Wood Facing FULL-SCALE TEMPLATE Dimension A For each model, the wine storage shelves have a natural cherrywood facing. You can replace these strips with wood more complementary to your design and surrounding cabinetry. Refer to the full-scale template below. ICB424G and ICB424FSG ICB427G and ICB427RG ICBWS-30 To remove the cherry strips, take the shelves out and remove the screws. Reverse the procedure to affix the new wood facing. IMPORTANT NOTE: If you choose to stain or seal the wood facing, be aware that some of these substances are hazardous and will damage stored wine. 16 mm MAXIMUM THICKNESS 3 mm 38 mm 21 mm A (WIDTH) FRONT VIEW WINE SHELF WOOD FACING WINE STORAGE MODELS 2 mm 9 mm 14 mm SIDE VIEW 495 mm 532 mm 624 mm Wine Storage 68 Door Clearance FULL-SCALE TEMPLATE Model ICB424G should extend a minimum of 6 mm beyond the front surface of adjoining cabinetry to allow for the maximum 145° door opening. The unit can be installed flush with adjacent cabinetry, however, there is potential for interference with the panel if the door is opened past 90°. MODEL ICB424 DOOR CLOSED 13 mm 19 mm DOOR PANEL 6 mm 3 mm MAXIMUM DOOR OPENING 145° 0 mm DOOR OPENING 145° TOP VIEW 25 mm SCALE Sub-Zero & Wolf Australian Distributor 1/151 Barkly Avenue Burnley Victoria 3121 Telephone 03 9421 0232 Facsimile 03 9421 0242 [email protected] www.subzerowolf.com.au ISZDG 2/ 2013