Download SERVICE MANUAL

Self Diagnosis
Supported model
SERVICE MANUAL
MODEL
KV-HF21M50
KV-XF21M80
COMMANDER
DEST. CHASSIS NO.
RM-952
Malaysia SCC-U21GA
RM-952
India
BG-3S CHASSIS
MODEL
COMMANDER DEST. CHASSIS NO.
SCC-U22G
TRINITRON ® COLOR TV
KV-HF21M50/XF21M80
RM-952
SPECIFICATIONS
Note
Power requirements
110-240 V AC, 50/60 Hz
For KV-XF21M80
220-240 V AC, 50/60 Hz
For KV-HF21M50
Power consumption (W) Indicated on the rear of the TV
Television system
B/G, I, D/K, M
Color system
PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58
Channel coverage
B/G
VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41
I
UHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K
VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
M
VHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘ (Antenna)
75-ohm external terminal
Audio output
5W + 5W
Number of terminal
D (Video)
Input: 2 Output: 1
Phono jacks; 1 VP-P, 75 ohms
≥ (Audio)
Input: 2 Output: 1
Phono jacks; 500 mVrms
Output: 1
Minijack
2 (Headphone)
Picture tube
21 inch
Tube size (cm)
54
Measured diagonally
Screen size (cm)
51
Measured diagonally
Dimension (w/h/d, mm)
640 × 456 × 488
Mass (kg)
27
Design and specifications are subject to change without notice.
CAUTION
SAFETY-RELATED COMPONENT WARNING!!
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
–2–
KV-HF21M50/XF21M80
RM-952
TABLE OF CONTENTS
Section
Title
Page
SELF DIAGNOSIS FUNCTION ................................ 4
Section
5-1.
5-2.
5-3
5-4.
(1)
(2)
(3)
(4)
5-5.
2. DISASSEMBLY
2-6.
2-7.
2-8.
Rear Cover Removal ................................................
Chassis Assy Removal .............................................
F Bracket Removal ..................................................
Service Position .......................................................
Replacement of Parts ...............................................
2-5-1.
Replacement of Control Button .......................
2-5-2.
Replacement of Light Guide ............................
Terminal Bracket Removal ......................................
Degauss Coil Removal .............................................
Picture Tube Removal ..............................................
22
22
22
22
23
23
23
24
24
24
Beam Landing ..........................................................
Convergence .............................................................
Focus Adjustment ....................................................
G2 (Screen) and White Balance Adjustments .........
6-1.
4-5.
Adjustments with Commander ................................
Adjustment Method .................................................
Picture Quality Adjustments ....................................
A Board Adjustment After IC003 (Memory)
Replacement .............................................................
Picture Distortion Adjustment .................................
39
42
44
45
47
50
56
61
65
Chassis ..................................................................... 67
7. ELECTRICAL PARTS LIST ....................................... 71
26
27
29
29
4. CIRCUIT ADJUSTMENT
4-1.
4-2.
4-3.
4-4.
Block Diagram .........................................................
Frame Schematic Diagram ......................................
Circuit Boards Location ..........................................
Schematic Diagrams and Printed Wiring Boards ...
Schematic Diagram of A (1/2) Board ......................
Schematic Diagram of A (2/2) Board ......................
Schematic Diagrams of C3 and C5 Boards .............
Schematic Diagrams of VM1 and F Boards ...........
Semiconductors ........................................................
6. EXPLODED VIEW
3. SET-UP ADJUSTMENTS
3-1.
3-2.
3-3.
3-4.
Page
5. DIAGRAMS
1. GENERAL ........................................................................ 8
2-1.
2-2.
2-3.
2-4.
2-5.
Title
30
31
36
36
37
–3–
KV-HF21M50/XF21M80
RM-952
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1.
DIAGNOSTIC TEST INDICATORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
No. of times
Self-diagnostic
STANDBY/TIMER display/Diagnostic
lamp flashes
result
Detected
Symptoms
Probable
Cause
Location
Does not light
—
• Power cord is not plugged
in.
• Fuse is burned out F4601
(F)
• Power does not come on.
• No power is supplied to the
TV.
• AC power supply is faulty.
• +B overcurrent
(OCP) or
overvoltage
(OVP)
• Vertical deflection
stopped
• Horizontal
deflection
overdrive
2 times
002:000 or
002:001~255
003:001~255
004:001~255
at the same time
• H.OUT Q511 is shorted. (A
board)
• IC1800 is shorted.
(C5 board)(KV-XF21M80)
• -13V is not supplied. (A
board)
• IC 503 faulty (A board)
• IC 301 faulty (A board)
• Power does not come on.
• Load on power line is
shorted.
• Has entered standby state
after horizontal raster.
• Vertical deflection pulse is
stopped.
• Power line is shorted or
power supply is stopped.
• White balance
failure (no
PICTURE)
5 times
005:000 or
005:001~225
• G2 is improperly adjusted.
(Note 2)
• CRT problem.
• Video OUT IC1800 is faulty.
(C5 board)(KV-XF21M80)
• IC301 is faulty. (A board)
• No connection A board to
C3 board (KV-HF21M50) &
C5 board (KV-XF21M80).
• No raster is generated.
• CRT cathode current
detection reference pulse
output is small.
—
101:00 or
101:001~225
• Discharge CRT (C3 & C5 Board) • Power is shut down shortly,
• Static discharge
after this return back to
• External noise
normal.
• Detect Micro latch up.
• Power does not
turn on
• Micro reset
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
–4–
KV-HF21M50/XF21M80
RM-952
2.
DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
2 times
5 times
Lamp ON 0.3 sec.
Lamp OFF 0.3 sec.
Lamp OFF 3 sec.
STANDBY/SLEEP lamp
Diagnostic Item
+B overcurrent/overvoltage
Vertical deflection stopped
Flash Count*
2 times
White balance failure
5 times
* One flash count is not used for self-diagnostic.
3.
STOPPING THE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.
–5–
KV-HF21M50/XF21M80
RM-952
4.
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] / channel [5] / Sound volume [-] / Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
SELF DIAGNOSTIC
002 : 000
003 : 000
004 : 000
005 : 001
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
101 : 000
5.
HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
–6–
KV-HF21M50/XF21M80
RM-952
6.
SELF-DIAGNOSTIC CIRCUIT
IC301
Y/CHROMA JUNGLE
FROM
CRT
FROM
[+B] Q604 C
IC001
SYSTEM
21 IK-IN
18
MP/
PROTECT
SDA 35
IO-8DAT 45
IC003
MEMORY
5 B-DAT
O-LED 51
46 IO-SDAT
[V] Q509/507
[+B overcurrent ªOCPº]
Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Vertical deflection stopped]
Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Vertical deflection overcurrent]
Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[White balance failure]
If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
–7–
SECTION 1
GENERAL
RM-952
Using Your New TV
WARNING
• Dangerously high voltages are present inside the TV.
• Operate the TV only between 110 – 240 V AC. (For KV_XF21M80)/220-240V AC
(For HF21M50)
Getting Started
Step 1
Connect the antenna (For KV-XF21M80)(India)
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
Do not open the cabinet and the rear cover of the
TV. Refer servicing to qualified personnel.
Install the TV in a stable position. Do not allow
children to climb onto it.
Rear of TV
IEC connector
(not supplied)
Antenna cable
(not supplied)
–8–
To prevent fire or shock hazard, do not expose
the TV to rain or moisture.
Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.
or
: Signal flow
Connecting a VCR
To watch the video, press …
(see page 12).
Rear of TV
Do not install the TV in a confined space, such
as a bookcase or built-in cabinet.
Do not block the ventilation openings of the TV.
Clean the TV with a dry and soft cloth.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.
Antenna cable (not supplied)
To antenna
VCR
output
To ˘
(antenna)
Do not pull the power cord to disconnect the TV.
Pull it out by the plug.
Do not plug in too many appliances to the same
power socket. Do not damage the power cord.
R
L(MONO)
AUDIO VIDEO
1
VIDEO IN
VIDEO OUT
To … 1
(video input)
To video and
audio outputs
: Signal flow
Audio/Video cable
(not supplied)
Disconnect the power cord during lightning
storms or if you are not going to use the TV for
several days.
2
Do not install the TV in hot, humid or excessively
dusty places.
4
Using Your New TV
(yellow)
-L (MONO) (white)
-R (red)
KV-HF21M50/XF21M80
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
Using Your New TV
Step 1
Connect the antenna (For KV-HF21M50)(Malaysia)
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
Rear of TV
Using Your New TV
Notes
• If you connect a monaural VCR, connect the yellow plug to
(the
yellow jack) and the black plug to -L (MONO) (the white jack).
• If you connect a VCR to the ˘ (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV.
• When no signal is input to the connected video equipment, the TV screen
becomes blue.
Getting Started
CAUTION
Do not connect the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
Step 2
IEC connector
(not supplied)
Insert the batteries
into the remote
Antenna cable
(not supplied)
Note
• Do not use old batteries nor use different types of batteries together.
or
: Signal flow
Step 3
Preset the channels automatically
Front of TV
–9–
Connecting a VCR
To watch the video, press …
1
(see page 12).
Rear of TV
Antenna cable (not supplied)
To antenna
VCR
output
2
ONE-PUSH AUTOMATIC PROGRAMING
1
1
VHF LOW B/G
To ˘
(antenna)
R
ONE-PUSH AUTOMATIC PROGRAMMING
Tips
• If you want to stop automatic channel presetting, press SELECT twice.
• If your TV has preset an unwanted channel or cannot preset a particular
channel, then preset your TV manually (see page 9).
L(MONO)
AUDIO VIDEO
1
VIDEO IN
VIDEO OUT
To … 1
(video input)
To video and
audio outputs
Note
• During automatic channel presetting, your TV screen will indicate “B/G”,
“I”, “D/K” or “M” for the TV system.
: Signal flow
Audio/Video cable
(not supplied)
Using Your New TV
Now You Are Ready. . .
To watch your TV, see page 11.
Using Your New TV
5
RM-952
KV-HF21M50/XF21M80
4
(yellow)
-L (MONO) (white)
-R (red)
RM-952
Connecting optional components
(For KV-XF21M80)
(For KV-HF21M50)
You can connect optional audio/video components, such as a VCR, multi disc player,
camcorder, video game or stereo system.
You can connect optional audio/video components, such as a VCR, multi disc player,
camcorder, video game or stereo system.
To watch the picture of the connected equipment, press …
To watch the picture of the connected equipment, press …
(see page 12).
Connecting a camcorder/video game equipment
using the … (video input) jacks
(see page 12).
Connecting a camcorder/video game equipment
using the … (video input) jacks
Front of TV
Front of TV
Audio/Video cable (not supplied)
Audio/Video cable (not supplied)
To video and
audio outputs
To… 2
(video input)
Camcorder
ONE-PUSH AUTOMATIC PROGRAMING
ONE-PUSH AUTOMATIC PROGRAMING
To video and
audio outputs
To… 2
(video input)
ONE-PUSH AUTOMATIC PROGRAMING
Camcorder
– 10 –
or
2
Video game
equipment
or
Video game
equipment
:Signal flow
2
Note
• You can also connect video equipment to the … 1 (video input) jacks at
the rear of your TV.
Connecting audio/video equipment using the Ú
(monitor output) jacks
Antenna cable (not supplied)
Rear of TV
L(MONO)
VCR
To
antenna
output
Audio system
or
1
To video and
audio inputs
To Ú
(monitor
output)
Audio/Video cable
(not supplied)
To
audio
inputs
or
(yellow)
-L (MONO)
(white)
-R (red)
:Signal flow
Note
• When connecting a monaural VCR, connect the yellow plug to
(the
yellow jack) and the black plug to -L (MONO) (the white jack).
6
Using Your New TV
: Signal flow
Note
• You can also connect video equipment to the … 1 (video input) jacks at
the rear of your TV.
6
Using Your New TV
KV-HF21M50/XF21M80
Connecting optional components
Presetting
channels
Securing the TV
u
To prevent the TV from falling, secure the TV using one of the following methods:
or
B
You can preset up to 100 TV channels in
numerical sequence from program
number 1 using the remote and the
buttons on your TV as well.
Using Your New TV
A
With the supplied screws, attach the band to the TV stand and to the rear of
the TV using the provided hole.
Put the cord or chain through the clamps to secure the TV against a wall or
pillar.
1
2
3
4
5
6
7
8
9
÷
0
JUMP
SOUND
MODE
Á
PROGR
Number buttons
. +/–
PROGR +/–
SELECT
PIC MODE
+ or –
FAVORITE
ONE-PUSH AUTOMATIC PROGRAMING
20
mm
TV
3.8mm
Presetting channels automatically
– 11 –
A
B
1
Press U to turn on the TV.
2
Press AUTO PROGR.
VHF LOW B/G
or
Note
• During automatic channel presetting, your TV screen will indicate “B/G”,
“I”, “D/K” or “M” for the TV system.
Note
• Use only the supplied screws. Use of other screws may damage the TV.
To preset channels automatically from a specified program number
(1) Press SELECT until “AUTO PROGRAM” appears.
(2) Press + or –.
The on-screen display will start flashing.
(3) Press PROGR +/– or the number buttons until the desired program number
appears.
Using Your New TV
7
8
Using Your New TV
RM-952
KV-HF21M50/XF21M80
(4) Press + or –.
RM-952
1
To change the color system setting
SELECT
If the color is abnormal when receiving programs through the ˘ (antenna) terminal
or the … (video input) jack
MANUAL PROGRAM
Using Your New TV
2
Press SELECT until
“MANUAL PROGRAM”
appears.
Press + or –.
VHF LOW B/G
3
Press PROGR +/– or the
number buttons until the
desired program number
appears.
1
PROGR
or
2
3
4
5
6
7
8
9
-/--
0
(1) Press SELECT until “COL SYS” appears.
COL SYS: AUTO
(2) Press + or – to select the appropriate color system until the color is optimal.
PAL
AUTO
SECAM
NTSC 3.58
NTSC 4.43
Tip
• Normally set “COL SYS” to “AUTO”.
– 12 –
Skipping program numbers
4
5
Press + or – until the
desired channel picture
appears.
1
Press SELECT.
SELECT
1
Press PROGR +/– or the number buttons until the unused or unwanted
program number appears.
2
3
4
5
Press SELECT until “MANUAL PROGRAM” appears.
Press + or –.
Press PIC MODE.
Press SELECT.
To preset the skipped program number again
To change the TV system setting
Preset the channel automatically or manually.
If the picture or sound is abnormal when receiving programs through the ˘ (antenna)
terminal
Tip
• You can also use SELECT and . +/– on the TV to preset channels and
skip program numbers.
(1) Press SELECT until “TV SYS” appears.
To use the fine tuning (FINE) function
The fine tuning (FINE) function may help to reduce the following problems: double
images and lines moving across the TV screen.
TV SYS: B/G
(2) Press + or – to select the appropriate TV system until the picture or sound quality
is optimal.
B/G
I
D/K
You can use the fine tuning function as below:
1) Select the program number you want to adjust.
2) Press SELECT until “MANUAL PROGRAM” appears on the screen.
3) Press + or – on the remote control once.
to display “FINE” on the screen.
4) Press
5) Press + or – continuously until the above problems are minimized.
The + or – icon on the screen flashes while tuning.
6) Press SELECT to return to normal screen.
M
continued
Using Your New TV
9
10
Using Your New TV
KV-HF21M50/XF21M80
Presetting channels (continued)
Presetting channels manually
Watching the TV
This section explains functions used
while watching the TV. Most operations
can be done using the remote.
Watching the TV (continued)
¤
u
…
;
1
2
Additional tasks
3
5
6
7
8
9
÷
0
JUMP
JUMP
SOUND
MODE
Á
PROGR
. +/–
PROGR +/–
SELECT p
SELECT
Using Your New TV
Number buttons
4
To
Do this
Turn off temporarily
Press u. The u indicator on the TV lights up red.
Turn off completely
Press U on the TV.
Mute the sound
Press ¤.
Watch the video input
(VCR, camcorder, etc.)
to select “VIDEO 1” or “VIDEO 2”.
Press …
To return to the TV program, press ;.
Jump back to the previous channel
Press JUMP.
.
Display the on-screen information*
Press
Adjust the volume of each TV
program automatically
Press SELECT repeatedly until “INTELLIGENT VOL”
appears, then press + or – to select “ON”.
PIC MODE p
+ or –
FAVORITE
FAVORITE
ONE-PUSH AUTOMATIC PROGRAMING
To cancel, select “OFF”.
TV
– 13 –
1
2
Press U to turn on the TV.
Changing the on-screen display language
When the TV is in the
standby mode (the u
indicator on the TV is lit
red), press u on the remote
or PROGR +/– on the TV.
Press PROGR +/– or the
number buttons to select
the TV program.
For double digit numbers,
press ÷, then the number
(e.g., for 25, press ÷, then
2 and 5).
3
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information
disappears after about 3 seconds.
1
1
PROGR
or
2
2
3
4
5
6
7
8
9
-/--
0
Press SELECT until
“LANGUAGE /
:
ENGLISH”appears on the
screen.
SELECT
LANGUAGE /
: ENGLISH
Press + or – to select
“
“.
LANGUAGE /
:
Tip
• You can also use SELECT and . +/– on the TV to select the on-screen
display language.
Press . +/– to adjust the
volume.
Using Your New TV
11
12
Using Your New TV
RM-952
KV-HF21M50/XF21M80
continued
RM-952
Setting the Wake Up timer
Changing the on-screen display language
(For KV-HF21M50)
2
Press SELECT until
: ENGLISH”
“LANGUAGE /
appears on the screen.
Press
until the
desired period of time
appears.
WAKE UP TIMER:10M
After 10 minutes
SELECT
b
LANGUAGE /
: ENGLISH
Press + or – to select
“.
“
b
/ LANGUAGE:
WAKE UP TIMER:12H00M
After 12 hours
2
Select the TV program or video mode you want to display when you wake
up.
3
Press u or set the Sleep timer if you want the TV to turn off automatically.
The
– 14 –
Tip
• You can also use SELECT and . +/– on the TV to select the on-screen
display language.
WAKE UP TIMER:OFF
No Wake Up timer
Using Your New TV
1
1
indicator on the TV lights up orange.
To cancel the Wake Up timer
Press
until “WAKE UP TIMER: OFF” appears or turn off the
TV’s main power.
Notes
• The Wake Up timer starts immediately after the on-screen display
disappears.
• If no buttons or controls are pressed for more than two hours after the
TV is turned on using the Wake Up timer, the TV automatically goes into
the standby mode. To continue watching the TV, press any button or
control on the TV or the remote.
Setting the Sleep timer
Press
until the
desired period of time
appears.
SLEEP TIMER:30M
After 30 minutes
SLEEP TIMER:60M
After 60 minutes
SLEEP TIMER:OFF
No Sleep Timer
SLEEP TIMER:90M
After 90 minutes
To cancel the Sleep timer
Press
12
Using Your New TV
until “SLEEP TIMER: OFF” appears or turn the TV off.
Using Your New TV
13
KV-HF21M50/XF21M80
Watching the TV (continued)
Advanced Operations
Customizing the
picture and sound
SOUND
MODE
Á
Adjusting the picture and sound settings
PROGR
SOUND MODE
1
SELECT
+ or –
You can customize the picture and
sound by selecting the picture and
sound modes or by adjusting its
settings.
Press SELECT until the
desired setting appears.
SELECT
PICTURE
60
PIC MODE
FAVORITE
Each time you press
SELECT, the setting
item will change as follows:
You can change the sound effect by
selecting the surround mode.
Selecting the picture and sound modes
PICTURE
COLOR
BRIGHT
BALANCE
TREBLE
BASS
2
Press + or – to adjust the item.
3
To adjust other items, repeat steps 1 to 2.
HUE*
SHARP
To select the picture mode
Press PIC MODE
repeatedly until you get
the desired picture mode.
PIC MODE
DYNAMIC
STANDARD
SOFT
* “HUE” can be adjusted for the NTSC system only.
To
DYNAMIC
receive high contrast pictures.
STANDARD
receive normal contrast pictures.
SOFT
receive mild pictures.
Notes
• When you select a picture or sound mode, the adjusted settings will be
reset according to the selected mode.
• You can also use SELECT and ¸ +/– on the TV to adjust the sound and
picture settings.
Selecting the surround mode
1
To select the sound mode
Press SOUND MODE
repeatedly until you get
the desired sound mode.
SOUND
MODE
≥ DYNAMIC
≥ DRAMA
≥ SOFT
2
To
DYNAMIC
listen to dynamic and clear sound that emphasizes the low and
high sound.
SELECT
Press + or – to select the
desired surround sound.
SURROUND: MOVIE
MOVIE
MUSIC
OFF
DRAMA
listen to sound that emphasizes vocals and background music.
Select
To
SOFT
receive soft sound.
MOVIE
listen to sound that spreads out over a large area, giving the feeling
of being at a movie theatre.
Advanced Operations
MUSIC
listen to the sound that gives the feeling of being at a live concert.
OFF
turn off the surround sound.
Advanced Operations
15
RM-952
KV-HF21M50/XF21M80
14
Select
Press SELECT repeatedly
until “SURROUND”
appears.
Advanced Operations
– 15 –
Select
RM-952
1
You can display six of your favorite
channels for quick and easy selection.
You can change the favorite channel
setting as well.
Blocking the
channels
(CHILD LOCK)
3
2
Number
buttons
6
4
5
7
8
9
÷
0
JUMP
SOUND
MODE
Á
PROGR
You can prevent a child from watching
certain programs by using the buttons
on the remote control.
PROGR +/–
+ or –
FAVORITE
2
3
4
5
6
7
8
9
÷
0
JUMP
SOUND
MODE
Á
PROGR
FAVORITE
Selecting a favorite channel
1
1
SELECT
Press FAVORITE.
FAVORITE CH
FAVORITE
+ or –
FAVORITE
– 16 –
1.PR01 2.PR02 3.PR03
4.PR04 5.PR05 6.PR06
TV
2
Press the number button
from 1 to 6 to select the
desired channel.
1
2
3
4
5
6
1
1
2
When you use the FAVORITE CH
feature for the first time, six preset channels will appear.
Select the TV program you want to lock.
Press SELECT until “CHILD
LOCK” appears on the
screen.
Changing the favorite channel setting
1
2
3
4
5
16
Press SELECT until
“FAVORITE CH SET UP”
appears.
3
SELECT
FAVORITE CH SET UP
1.PR01 2.PR02 3.PR03
4.PR04 5.PR05 6.PR06
Press + or – to select the
favorite channel you want
to change (e.g. 3 PR03).
Press PROGR +/–, or
number buttons to
change the program
number.
FAVORITE CH SET UP
1.PR01 2.PR02 3.PR03
4.PR04 5.PR05 6.PR06
PROGR
or
1
2
3
4
5
6
7
8
9
-/--
0
FAVORITE CH SET UP
1.PR01 2.PR02 3.PR08
4.PR04 5.PR05 6.PR06
SELECT
CHILD LOCK: OFF
Press + or – to select
“ON”.
1
symbol appears on
The
the screen.
To unlock the channel,
press + or – to select
symbol
“OFF”. The
disappears from the screen.
CHILD LOCK: ON
Note
• If you preset a locked channel, that particular channel will be unlocked
automatically.
Repeat steps 2 and 3 to set other favorite channels.
Press SELECT.
Advanced Operations
Advanced Operations
17
KV-HF21M50/XF21M80
Viewing your
favorite channels
Additional Information
Self-diagnosis
function (For KV-XF21M80)
Your TV is equipped with a self-diagnosis function. If there is a
problem with your TV, the u indicator flashes red. The number of
times the u indicator flashes indicates the possible causes.
Front of TV
ONE-PUSH AUTOMATIC PROGRAMING
u indicator
– 17 –
1
Check that the u indicator flashes red a number of times between 3-second
intervals.
2
3
4
Count the number of times the u indicator flashes.
Press U (main power) to turn off your TV.
Inform your nearest Sony service center about the number of times the
u indicator flashes.
Be sure to note the model name and serial number located on the rear of
your TV.
RM-952
KV-HF21M50/XF21M80
18 Additional Information
RM-952
Troubleshooting Shortcuts
(For KV-HF21M50)
For better viewing, please check the following connections.
Antenna connection
AC Connection
Check the antenna direction.
Incorrect antenna direction may cause:
• Snowy
picture
UHF
• Distorted
picture
VHF
• Noisy/
distorted
sound
• Double image
picture
Check connection on
the AC socket.
Loose connection may cause:
• no power
• no picture with no sound
– 18 –
Wall antenna
terminal
Booster
Check the antenna
type.
Wrong type of antenna
may cause:
Check connection
on the wall
antenna terminal.
VCR
Check if you need
booster to increase
signal level.
Connection
to TV
Check connection
on the VCR and on
the TV.
Too strong signal level
may cause:
Loose connection may
cause:
• No picture
• Snowy picture
• Distorted picture
• Snowy picture
• Snowy picture
• Distorted sound
• Noisy sound
• Distorted sound
For more information, please see
“Troubleshooting” on page 20, 21 and
22 or consult your dealer for
guidance.
• No picture
18
Additional Information
Additional Information
Additional Information
Loose connection may
cause:
19
KV-HF21M50/XF21M80
Additional Information
Troubleshooting
Troubleshooting (continued)
If you find any problem while viewing your TV, please check the following guide. If
any problem persists, contact your Sony dealer .
Symptom
Snowy picture
Solutions
Symptom
Distorted picture
– 19 –
Possible cause
• The volume level is too low.
• Press ¤ to cancel the muting.
• The sound is muted.
Dotted lines or stripes
• Do not use a hair dryer or other
equipment near the TV.
• Adjust the antenna direction for
minimum interference. Contact a Sony
dealer for advice.
• There is local interference
from cars, neon signs, hair
dryers, power generators,
etc.
Double images or
“ghosts”
• Use a highly directional antenna.
• Use the fine tuning (FINE) function.
(page 10)
• Broadcast signals are
reflected by nearby
mountains or buildings.
• Adjust the antenna direction. Contact a
Sony dealer for advice.
• The antenna direction is
inapproprite.
Possible cause
• Check the antenna cable and connection • Connection is loose or the
on the TV, VCR and on the wall. (page 4)
cable is damaged.
• Press SELECT until “MANUAL
• Channel presetting is
PROGRAM” appears on the screen then
inappropriate or
preset the channel again. (page 9)
incomplete.
Noisy sound
Solutions
• Press ¸ + to increase the volume level.
Good picture
• Check the antenna type (VHF/UHF).
Contact a Sony dealer for advice.
• The antenna type is
inappropriate.
• Adjust the antenna direction. Contact a
Sony dealer for advice.
• The antenna direction is
inappropriate.
• Try using a booster.
• Signal transmission is low.
No sound
• Turn off or disconnect the booster if it is • Broadcast signals are too
in use.
strong.
Noisy sound
• Turn off or disconnect the booster if it is • Use of a booster is
inappropriate.
in use.
• If the sound of all the channels are
noisy, check the TV system (TV SYS)
setting (page 9), then press AUTO
PROGR to preset the channels again.
(page 8)
Noisy sound
• If the sound of some channels are noisy,
select the channel, then select the
appropriate TV system (TV SYS).
(page 9)
No picture
No sound
• The TV system setting or
channel presetting is
inappropriate or
incomplete.
• Check the power cord, antenna and the
VCR connections.
• The power cord, antenna
or VCR is not connected.
• Press u (power).
• The TV is not turned on.
No color
Additional Information
Good picture
• Press U (main power) on the TV to turn
off the TV for about five seconds, then
turn it on again.
• Press SELECT until “COLOR” appears • The color level setting is
too low.
on the screen, then press + or – to adjust
the color level. (page 15)
• Press SELECT until “COL SYS ” appears • The color system setting is
inappropriate.
on the screen, then check the color
system setting (usually set this to
“AUTO”). (page 10).
Abnormal color patches
• Adjust the antenna direction. Contact a
Sony dealer for advice.
• The antenna direction is
inapproriate.
• Keep external speakers or other
electrical equipment away from the TV.
Do not move the TV while the TV is
turned on. Press U (main power) on
the TV to turn off the TV for about five
minutes, then turn it on again.
• The magnetic disturbance
from external speakers or
other equipment, or the
direction of the earth’s
magnetic field may affect
the TV.
Additional Information
19
20 Additional Information
RM-952
KV-HF21M50/XF21M80
continued
RM-952
Solutions
Possible cause
Lines moving across the
TV screen.
• Use the fine tuning (FINE) function.
(page 10)
• There is interference from
external sources, e.g.,
heavy machineries, nearby
broadcast station.
The u (standby) indicator
on your TV flashes red for
about 3 seconds per
interval.
• Contact your nearest Sony service
center.
• Your TV may need service.
TV cabinet creaks.
—
– 20 –
A “boom” sound is heard
when the TV is turned on.
—
Refer to the pages indicated in parentheses ( ) for details.
Front panel
• Changes in room
temperature sometimes
make the TV cabinet
expand or contract, making
a noise. This does not
indicate a malfunction.
ONE-PUSH AUTOMATIC PROGRAMING
• The TV’s demagnetizing
function is working. This
does not indicate a
malfunction.
2
ONE-PUSH AUTOMATIC PROGRAMMING
1
U (main power) button (11)
2 PROGR +/– (program) buttons (11)
3
4
¸ +/– (volume) buttons (11)
… (TV/video) button (12)
5 AUTO PROGR (program) button (5)
6 SELECT button (10)
7
Additional Information
21
2 (headphone) jack
22 Additional Information
KV-HF21M50/XF21M80
Identifying parts and controls
Symptom
Self-diagnosis
function (For KVHF21M50)
Remote Control
9
Your TV is equipped with a self-diagnosis function. If there is a
problem with your TV, the u indicator flashes red. The number of
times the u indicator flashes indicates the possible causes.
!º
!¡
Front of TV
!™
1
2
1
2
3
4
5
6
7
8
9
÷
0
JUMP
SOUND
MODE
Á
PROGR
!¶
3
4
1
2
3
4
5
6
7
8
9
÷
0
JUMP
SOUND
MODE
Á
PROGR
!§
5
!£
SELECT p
!¢
PIC MODE p
FAVORITE
ONE-PUSH AUTOMATIC PROGRAMING
SELECT p
6
PIC MODE p
7
FAVORITE
8
!∞
TV
TV
u indicator
– 21 –
1
Check that the u indicator flashes red a number of times between 3-second
intervals.
2
3
4
Count the number of times the u indicator flashes.
1 u (power) button (11)
2 ; (TV) button (12)
3 Number buttons (11)
4 JUMP button (12)
5 PROGR +/– buttons (11)
6 SELECT button (9)
7 PIC MODE button (14)
8 +/– buttons (9)
(display) button (12)
9
!º ¤ (muting) button (12)
!¡ … (video) button (12)
!™ . +/– (volume) buttons (11)
!£ A/B button
(not used for this models)
!¢ Timer setting buttons (13)
(wake up timer)
(sleep timer)
!∞ FAVORITE button (16)
Press U (main power) to turn off your TV.
Inform your nearest Sony service center about the number of times the
u indicator flashes.
Be sure to note the model name and serial number located on the rear of
your TV.
23
Names/symbols of buttons on the
remote are indicated in different
colors to represent the available
functions.
Label color
Button function
White
For general TV operations
Green
For Teletext operations
Additional Information
23
RM-952
KV-HF21M50/XF21M80
Additional Information
!§ SOUND MODE button (14)
!¶ Teletext operation buttons
(not used for this models)
(text)
(enlarge)
(reveal)
(hold)
(index)
(text clear)
p (FASTEXT: red, green, yellow, blue)
DISASSEMBLY
2-3. F BRACKET REMOVAL
RM-952
2-1. REAR COVER REMOVAL
2 Rear cover
2 F board
1 Three connectors
Lever
– 22 –
1 Two screws
(+BVTP 4 × 16)
1 Eight screws
(+BVTP 4 × 16)
2-2. CHASSIS ASSY REMOVAL
2-4. SERVICE POSITION
(Note: Remove F Bracket first.)
Lever
Lever
One screw
(+BVTP 4x16)
1 Chassis assy
KV-HF21M50/XF21M80
SECTION 2
2-5. REPLACEMENT OF PARTS
For replacement of the Multi Button (KV-XF21M80), cut the welded portions from them,
exchange with the new parts, and fix them with screws (+BVTP) respectively.
2-5-2. REPLACEMENT OF LIGHT GUIDE
For replacement of light guide (KV-XF21M80), cut the welded portions from it,
exchange with new parts, fix it with screw (+BVTP)
2-5-1. REPLACEMENT OF MULTI BUTTON
Light guide
Light guide
Cut
Multi button
Cut
One screw
(+BVTP 3 × 12)
(XF21M80)
Multi button
Two screws
(+BVTP 3 × 12)
For replacement of Light Guide (KV-HF21M50), pull it out to exchange with the new
part.
– 23 –
(XF21M80)
For replacement of the Multi Button (KV-HF21M50), unscrew it to exchange with new
parts, and fix it with screws (+BVTP).
Light guide
Multi button
(HF21M50)
(HF21M50)
RM-952
KV-HF21M50/XF21M80
Two screws
(+BVTP 3 × 12)
2-8. PICTURE TUBE REMOVAL
4 C3 (KV-HF21M50)
/C5 board (KV-XF21M80)
RM-952
Terminal board bracket
3 F board
7 Neck assy
One screw
(+BVTP 4x16)
5 Deflection yoke
2 A board
6 Four screws
(Tapping screws)
A board
– 24 –
1 Anode cap
2-7. DEGAUSS COIL REMOVAL
Cushion
1 Demagnetization coil
2 Tension spring
Picture tube
KV-HF21M50/XF21M80
2-6. TERMINAL BRACKET REMOVAL
• REMOVAL OF ANODE-CAP
NOTE : After removing the anode, short circuit the anode of the picture tube and
the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.
• REMOVING PROCEDURES
a
a
1 Turn up one side of the rubber cap in the direction indicated by the arrow a.
b
b
– 25 –
2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
c
Anode button
3 When one side of the rubber cap is separated from the anode button, the anode-cap
can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow c.
•
HOW TO HANDLE AN ANODE-CAP
RM-952
KV-HF21M50/XF21M80
1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built into the rubber.
3 Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.
KV-HF21M50/XF21M80
SECTION 3
RM-952
SET-UP ADJUSTMENTS
•
•
The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.
These adjustments should be performed with rated power
supply voltage unless otherwise noted.
Controls and switches should be set as follows unless otherwise noted:
PICTURE control ........................................................... normal
BRIGHTNESS control ................................................... normal
Perform the adjustments in the following order :
1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note : Test Equipment Required.
1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope
................................................................................................................................................................................................................................
Preparation :
• In order to reduce the influence of geomagnetism on the set's
picture tube, face it east or west.
• Switch on the set's power and degauss with the degausser.
Neck assy
DY
3-1. BEAM LANDING
1. Input a white signal with the pattern generator.
Contrast
normal
Brightness
2. Position neck assy as shown in Fig3-2.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the purity
control so that the green is at the center and the blue and the red
take up equally sized areas on each side.
(See Figures 3-1 through 3-3.)
5. Move the deflection yoke forward and adjust so that the entire
screen is green. (See Figure 3-1.)
6. Switch the raster signal to blue, then to red and verify the
condition.
7. When the position of the deflection yoke has been decided,
fasten the deflection yoke with the screws and DY spacers.
8. If the beam does not land correctly in all the corners, use a
magnet to adjust it.
(See Figure 3-4.)
Note:
Neck Assy is exactly behind
DY (no gap between Neck
Assy and DY)
}
Fig. 3-2
Blue
Red
Green
Fig. 3-3
Purity control corrects
this area.
b
a
c
d
Disk magnets or rotatable
disk magnets correct
these areas (a-d).
Deflection yoke positioning
corrects these areas.
b
c
a
Fig. 3-1
d
Fig. 3-4
– 26 –
KV-HF21M50/XF21M80
RM-952
3-2. CONVERGENCE
Preparation :
• Before starting this adjustment, adjust the focus, horizontal size
and vertical size.
• Minimize the brightness setting.
• Provide dot pattern.
1 V. STAT
a
b
(1)
b
Horizontal and Vertical Static Convergence
Center dot
b
a
B
B
G
G
R
R
2 H. STAT VR
R
a
G
b
B
R
G
B
R
H. STAT VR
G
B
B
R
G
V.STAT Magnet
3
a
b
b
a
B
R
G
RV 702
b
G
R
B
4 BMC (Hexapole) Magnet.
If the red, green and blue dots are not balanced or aligned, then
use the BMC magnet to adjust in the manner described below.
C3 board (KV-HF21M50)
C5 board (KV-XF21M80)
(Moving vertically), adjust the V.STAT magnet so that the red, green
and blue dots are on top of each other at the center of the screen.
Purity
R G
B
R
B
R
G
B
R
G
B
R
G B
BMC
G
G
R
BMC (Hexapole)
Purity
V.STAT
V.STAT
– 27 –
B
KV-HF21M50/XF21M80
RM-952
4 Y separation axis correction magnet adjustment.
Red
Blue
1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN]
and [BRIGHTNESS] to [STANDARD] .
Neck assy
2. Adjust the Y separation axis correction magnet on the neck
assembly so that the horizontal lines at the top and bottom of
the screen are straight.
Neck assy
Red
VM1 board
Blue
VM1 board
Note
1. The Red and Blue magnets should be equally far from the
horizontal center line.
2. Do not separate the Red and Blue magnets too far. (Less than
8 mm)
(2) Dynamic Convergence Adjustment
Preparation:
• Before starting this adjustment, adjust the horizontal static
convergence and the vertical static convergence
RB
B
R
YCH
TLV
on DY
YCH
TLV
– 28 –
KV-HF21M50/XF21M80
RM-952
3-4. G2 (SCREEN) AND WHITE BALANCE
ADJUSTMENTS
(3) Screen-corner Convergence
b
1.
1)
2)
3)
G2 (SCREEN) ADJUSTMENT
Set the PICTURE to normal.
Put to VIDEO input mode without signals.
Connect R, G and B of the C3/C5 board cathode to the oscilloscope.
4) Adjust BRIGHTNESS to obtain the cathode voltage to the value
below.
5) Adjust G2 (Screen) on FBT until picture shows the point
before cut-off.
a
a-d : screen-corner
misconvergence
c
d
Fix a Permalloy assy corresponding to the misconverged
areas.
Fix a Permalloy assy
corresponding to the
misconverged areas
175 V ±2(VDC)
b
0V
a
2. WHITE BALANCE ADJUSTMENT
1) Set to Service Mode (Refer Section 5-1: ADJUSTMENTS
WITH COMMANDER).
2) Input white raster signal.
3) Set the PICTURE to minimum.
4) Select GCT (WHB 4) and BCT (WHB 5) with [1] and [4], and
adjust the level with [3] and [6] for the best white balance.
5) Set the PICTURE to maximum.
6) Select GDR (WHB 1) and BDR (WHB 2) with [1] and [4], and
adjust the level with [3] and [6] for the best white balance.
7) Write into the memory by pressing [MUTING] then [0].
c
d
a to d : Permalloy assembly
3-3. FOCUS ADJUSTMENT
Adjust FOCUS control on the flyback transformer for the best
focus.
3. SUB BRIGHT ADJUSTMENT
1) Set to service mode.
2) Input a staircase signal of black to white from the pattern
generator.
3) BRIGHTNESS .... 50%.
PICTURE ............ MINIMUM
4) Select SBR (WHB7) with [1] and [4], and adjust SBR (WHB7)
level with [3] and [6] so that the second stripe from the right is
dimly lit.
White
second from the right
Black
FOCUS
SCREEN
FLYBACK TRANSFORMER (T503)
– 29 –
KV-HF21M50/XF21M80
SECTION 4
RM-952
CIRCUIT ADJUSTMENTS
4-1. ADJUSTMENTS WITH COMMANDER
Service adjustments are made with the RM-952 that comes with
this unit.
a. ENTERING SERVICE MODE
With the unit on standby
↓
[DISPLAY]
↓
5
↓
1, 4
↓
3, 6
↓
Select the adjustment item.
[MUTING]
Writes.
↓
7, 8, 5, -
VOL (+)
↓
[POWER]
This operation sequence puts the unit into service mode.
2, -
Raise/lower the data value.
Executes the writing.
All the data becomes the values in memory.
All user control goes to the standard state.
Service data initialization (Be sure not to use
usually.)
Write 50Hz adjustment data to 60Hz, or vice
versa.
b. METHOD OF CANCELLATION FROM SERVICE
MODE
Set the standby condition (Press [POWER] button on the commander),
then press [POWER] button again, hereupon it becomes TV mode.
c.
1)
2)
3)
4)
METHOD OF WRITE INTO MEMORY
Set to Service Mode.
Press [1] (UP) and [4] (DOWN), select an item of adjustment.
Press [MUTING] button and it will indicate WRITE on the screen.
Press [0] button to write into memory.
d. MEMORY WRITE CONFIRMATION METHOD
1) After adjustment, pull out the plug from AC outlet, and then
plug into AC outlet again.
2) Turn the power switch ON and set to Service Mode.
3) Call the adjusted items again to confirm adjustments were made.
1
2
3
4
5
6
7
8
9
÷
0
JUMP
SOUND
MODE
Á
PROGR
The screen display is :
FAVORITE
Device Name
Marking of virgin NVM
Item Name
Item No
Mode
Data
TV
GEO
00
HPS
1C
p
SERVICE
622S
or
623S
1.0C
59
7F
0
000A
Suffix No
(OEM Code)
Software version
50
PAL, SECAM : 50
NTSC
Total Power-On time (hours)
– 30 –
: 60
RM-952
KV-HF21M50/XF21M80
RM-952
4-2. ADJUSTMENT METHOD
Item Number 00 of device GEO
This explanation uses H-Position as an example.
1. Select “GEO 00 HPS” with the 1 and 4 buttons.
2. Raise/lower the data with the 3 and 6 buttons.
3. Select the optimum state. (The standard is 1F for PAL reception.)
4. Write with the [MUTING] button. (The display changes to
WRITE.)
5. Execute the writing with the - button. (The WRITE
display will be changed to red color while excuting, and back
to SERVICE.)
GEO
00
622S 1.0C
or
623S
GEO
00
622S 1.0C
or
623S
HPS
1F
59
7F
SERVICE 50
0
HPS
1F
WRITE
50
59
7F
0
000A
000A
Use the same method for all Items. Use 1 and 4 to select the
adjustment item, use 3 and 6 to adjust, write with [MUTING],
then execute the write with -.
Note : 1. In [WRITE], the data for all items are written into memory
together.
2. For adjustment items that have different standard data
between 50Hz or 60Hz, be sure to use the respective
input signal after adjustment.
GREEN
Adjusted with [3]
and [6] buttons.
GREEN
Written with [MUTING]
GEO
00
622S 1.0C
or
623S
HPS
1F
59
7F
SERVICE 50
0
000A
RED
The WRITE display
then the display
returns to a green
SERVICE.
Write executed with [0]
– 31 –
Device
Name
GEO
Functionality
No
Name
Note
Data Range
Function
Register
No. (bit)
Slava
Address
RAM Address
(bit)
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
50/60HZ
CXA2130S(88H)
50/60HZ
50/60HZ
12 (7-2)
11 (7-2)
13 (7-2)
15 (7-4)
0F (7-2)
0E (7-2)
10 (7-4)
10 (3-0)
16 (7-4)
16 (3-0)
14 (7-2)
18 (7-2)
18 (1)
17 (7-4)
17 (3-0)
82 (7-2)
81 (7-2)
83 (7-2)
85 (7-4)
7F (7-2)
7E (7-2)
80 (7-4)
80 (3-0)
86 (7-4)
86 (3-0)
84 (7-2)
88 (7-2)
67 (1)
87 (7-4)
87 (3-0)
DYNAMIC/others
DYNAMIC/others
DYNAMIC/others
SECAM/others
SECAM/others
SECAM/others
09 (7-2)
0A (7-2)
0B (7-2)
07 (3-0)
08 (7-4)
08 (3-0)
CXA2130S(88H)
8F (7-2)
90 (7-2)
91 (7-2)
93 (3-0)
94 (7-4)
94 (3-0)
97
98
CXA2130S(88H)
96
99
9A
9B
CXA2130S(88H)
85 (3-0)
1A3 (1-0)
8C (3-0)
6A (1-0)
6A (3-2)
6B (1-0)
6B (7-2)
59 (1)
58 (1)
58 (0)
198 (1)
55 (1)
199 (0)
HPS
HSZ
PAP
TLT
VPS
VSZ
SCO
VLN
BOW
AGL
UPN
LPN
HBL
LBL
RBL
7
1F
1F
7
1F
1F
7
7
7
7
1F
2F
1
7
7
3F
3F
3F
0F
3F
3F
0F
0F
0F
0F
3F
3F
1
0F
0F
H Position
H Size
Pin Amp
Trapezium
V Position
V Size
S Correction
V Linearity
AFC Bow
AFC-Angle
Upper Pin
Lower Pin
H Blanking on/off
Left H Blanking
Right H Blanking
WHB
0
1
2
3
4
5
6
7
RDR
GDR
BDR
RCT
GCT
BCT
BMN
SBR
2A
2A
2A
7
7
7
15
28
3F
3F
3F
0F
0F
0F
1F
3F
R Drive
G Drive
B Drive
R Cutoff
G Cutoff
B Cutoff
Brightness Minimum Data
Sub Brightness Control
SAJ
0
1
2
3
PMX
SHU
SSH
SCL
33
8
3
1F
3F
0F
0F
3F
Picture Maximum Data
Sub Hue Control
Sub Sharpness Control
Sub Color Control
0
1
2
3
4
5
6
7
8
9
10
11
12
EHT
GMA
YDL
SST
SSP
SLV
SBF
DYC
ABL
VTH
SF0
DCX
SHT
4
2
6
1
1
2
22
0
1
1
1
1
1
0F
03
0F
03
03
03
3F
1
1
1
1
1
1
EHT Comp
50/60HZ
Gamma Correction
NTSC/others
Y Delay
PAL/SECAM/NTSC
SECAM ID Start Position
SECAM ID Stop Position
SECAM ID Level
SECAM BELL fO
Dynamic Color on/off
ABL Mode Switching (except STANDARD)
ABL Detection Vth Switching
FO Switching for Sharpness
NTSC/others
DC Trans. Ratio Switching
Pre-/Overshoot ratio Switch
NTSC/others
– 32 –
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VP
A
TV/Video
TV/Video
NTSC/others
15 (3-0)
0B (1-0)
0C (3-0)
1B (1-0)
1B (3-2)
1C (1-0)
1C (7-2)
0A (1)
09 (1)
09 (0)
05 (1)
06 (1)
06 (0)
RM-952
Note for
Different Data
KV-HF21M50/XF21M80
Adjustment Item Table
Adjustment Item Table
Device
Name
VP
AP
– 33 –
MSP
Functionality
No
Name
Note
Data Range
Function
0
1
7
0
0
1
0
1
1
1
1
1
0
0
1
03
0F
1
1
1
1
3
1
1
1
1
1
1
H Drive Pulse Width Switch
AFC Gain Control
H Oscillation
Slice Level of H Sync Sep.
Slice Level of V Sync Sep.
Macro Vision C/m off/on
YUV Switch Control
CD mode for Video
R ON
G ON
B ON
P ON
BLK Off
VM Off
0
1
2
3
4
5
6
7
8
INF
INS
PH1
PH2
PH3
PH4
BCS
TCS
TRF
0
0
0
0
0
0
2
2
2
3F
3F
3
3
3
3
3
3
3
Input Attenuation When surround off
Input Attenuation When surround on
Phase 1 Register Selection
Phase 2 Register Selection
Phase 3 Register Selection
Phase 4 Register Selection
Bass Center Shift
Treble Center Shift
RF Treble Offset
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
WST
WBT
WLL
WAC
WDL
NDL
SDL
AGC
REL
CRM
ACO
FP
FPM
FH
FHM
WGP
NIP
ERR
VOL
15
EA
5
0
30
20
10
1
28
0
1
1B
32
36
65
2A
6D
50
6D
FF
FF
FF
0F
FF
FF
FF
1
3F
1
1
7F
7F
7F
7F
7F
7F
FF
FF
W/G Stereo Threshold
W/G Bilingual Threshold
W/G Monaural Threshold
W/G Agreement Count
W/G Search Delay
NICAM Search Delay
Stereo status Read Delay
AGC Switch Auto/Constant
AGC Gain at Constant Mode
Carrier muting on/off
Audio Clock out on/off
FM Prescale for non-M system
FM Prescale for M system
FM Prescale for HDEV
FM Prescale for HDEV and M
W/G Prescale
NICAM Prescale
Auto FM switch Threshold
Loud Speaker gain 7000h to 7ffoh
TV/Video/Text
50/60Hz
Video only
not memorized
not memorized
not memorized
not memorized
Slava
Address
00 (6)
0F (1-0)
0C (7-4)
0D (1)
0D (0)
0E (0)
01 (0)
0D (5-4)
01 (3)
01 (2)
01 (1)
00 (7)
12 (0)
13 (0)
00 (5-0)
4F (6)
8D (1-0)
5B (7-4)
5C (1)
5C (0)
7E (0)
50 (0)
1A1 (5-4)
50 (3)
50 (2)
50 (1)
4F (7)
61 (0)
62 (0)
TDA7429
19D (5-0)
1A0 (5-0)
76 (1-0)
76 (3-2)
76 (5-4)
76 (7-6)
1A8 (1-0)
1A9 (1-0)
1A9 (5-4)
MSP3415D(84H)
(844)
157 (7-0)
158 (7-0)
159 (7-0)
15A (3-0)
15B (7-0)
15C (7-0)
15D (7-0)
108 (7)
108 (6-1)
107 (9)
10C (5)
16C (6-0)
16D (6-0)
16E (6-0)
16F (6-0)
170 (6-0)
138 (6-0)
166 (7-0)
1A7 (7-0)
02
#4 (3-0)
#5 (3-0)
#5 (3-0)
BB (7)
BB (6-1)
BB (9)
83 (5)
0E (7-0)
0E (7-0)
0E (7-0)
0E (7-0)
0E (7-0)
10 (7-0)
21 (10-3)
0000 (15-4)
RAM Address
(bit)
RM-952
HDW
AFC
HOS
HSS
VSS
HMS
YUV
CDV
RON
GON
BON
PON
BLK
VMC
Register
No. (bit)
KV-HF21M50/XF21M80
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Note for
Different Data
Device
Name
Functionality
No
Name
Note
Data Range
Function
Note for
Different Data
Register
No. (bit)
RAM Address
(bit)
(58H)
18D (1-0)
18D (6-4)
TXT
0
1
TXH
TXV
1
0
3
3
Teletext Horizontal Position
Teletext Vertical Position
OPM
0
1
2
3
4
5
6
7
8
OSH
COM
APC
TSY
MUT
AFM
RFB
TVO
DBL
0A
0
1
0
0
0
0
0
0
3F
03
1
03
1
1
3
7
1
OSD H Position
Comb Selection
APC Switch
TV Sys at Auto TV Sys
No Signal Mute
Auto FM switch
C-BPF Control
Tilt to V-Angle offset
Disable Blueback Function
Option-Misc
AC (7-2)
A5 (7-6)
A4 (5)
A4 (4-3)
A4 (0)
A4 (1)
A5 (5-4)
A5 (2-0)
A4 (2)
OPB
0
1
2
OP1
OP2
OP3
FF
1
0
FF
FF
FF
Optional Bits 1 (see below)
Optional Bits 2 (see below)
Optional Bits 3 (see below)
Option-Bits
45
46
47
– 34 –
NOTE
shaded items are fixed data.
•
• Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode.
• Note for Different Data
Those are the standard data values written on the microprocessor. Therefore, the data values of the modes and stored respectively in the
memory.
In case of a device replacement, adjustment by rewriting the data value is necessary for some items.
RM-952
Slava
Address
KV-HF21M50/XF21M80
Adjustment Item Table
KV-HF21M50/XF21M80
RM-952
ITEM INFORMATION.
No. OPB0 OP1
XTAL 4.43
XTAL 3.58
SECAM
2nd. Lang
B/G
I
D/K
M
KV-HF21M50
1
1
1
1
1
1
1
1
KV-XF21M80
1
1
1
1
1
1
1
1
TOP
NICAM
HDEV
Thai Bil
Dis. Fav
DVD Input
KV-HF21M50
0
0
0
0
0
0
1
0
KV-XF21M80
0
0
0
0
0
0
1
0
Pic Rot
2199
Auto PIC
Auto TV sys
US ST
AV Mono
11 KEY
Color SW
KV-HF21M50
0
0
1
0
0
0
0
0
KV-XF21M80
1
0
1
0
0
0
0
0
Item
No. OPB1 OP2
Item
AV Input
No. OPB2 OP3
Item
– 35 –
KV-HF21M50/XF21M80
RM-952
4-3. PICTURE QUALITY ADJUSTMENTS
SUB COLOR ADJUSTMENT
BELL FILTER ADJUSTMENT
1. Input a PAL color-bar.
2. Set to the following condition:
PICTURE 100%, BRIGHTNESS 50%, COLOR 50%
3. Connect an oscilloscope to pin 1 (B OUT) of CN305, A board.
4. Set to Service Mode and select SAJ 3 ‘SCL’ with 1 and 4 of
the commander then adjust to VB2=VB3=VB4 with 3 and
6.
5. Press [MUTING] → - of the commander to write the data.
6. Adjust SAJ 3 ‘SCL’ as step 2 to 5 when receiving NTSC colorbar.
1. Input SECAM color-bar signal.
2. Connect the dual-trace oscilloscope to the pin 9 (R-Y) of
CN303 (not mounted).
3. Adjust SERVICE MODE, ITEMS ‘SBF’ as shown below.
4-4. A BOARD ADJUSTMENT AFTER IC003
(MEMORY) REPLACEMENT
VB1 VB2
When replacing IC003 (MEMORY), be sure to change IC001 (µCOM) to the following new IC at the same time.
IC001(µ-CON):CXP86449-622S (KV-XF21M80)
CXP86449-623S (KV-HF21M50)
VB3 VB4
VB2 = VB3 = VB4
1. Enter to Service Mode.
SUB HUE ADJUSTMENT
1. Select Video 1.
2. Input a NTSC color-bar, video into Video 1.
3. Set the following condition:
PICTURE 100%, BRIGHTNESS 50%, COLOR 50%
4. Connect an oscilloscope to pin 1 (B OUT) of CN305, A board.
5. Select SAJ 1 ‘SHU’ with 1 and 4 of the commander by setting to Service Mode and adjust to VB1=VB2=VB3=VB4 with
3 and 6.
2. Press commander buttons 5 and - (Data Initialize), and 2
and - (Data Copy) to initialize the data.
3. Call each item number and check if the respective screen shows
the normal picture.
In cases where items are not well adjusted, rectify the items
with fine adjustment.
Write the data per each item number ([MUTING] +-).
4. Select item numbers “OPB0” (OP1), “OPB1” (OP2) and
“OPB2” (OP3) and respectively set the bit per model with
command buttons 3 and 6.
VB1 VB2
VB3 VB4
5. Press commander buttons 8 and - (Test Normal) to return
to the data that was set on the shipment from the factory.
(This will also cancel Service Mode.)
VB1 = VB2 = VB3 = VB4
6. Press [MUTING] → - of the commander to write the data.
– 36 –
KV-HF21M50/XF21M80
RM-952
4-5. PICTURE DISTORTION ADJUSTMENT
Item Number 00 – 0B
GEO 0
HSH (H POSITION)
GEO 1
HSZ (H SIZE)
GEO 2
PAP (PIN AMP)
GEO 3
TILT (TRAPEZIUM)
GEO 4
VSH (V POSITION)
GEO 5
VSZ (V SIZE)
GEO 6
SCR (VERTICAL S-Correction)
GEO 7
VLN (V LINEARITY)
GEO 8
VBOW (AFC.BOW)
GEO 9
AGL (AFC.ANGLE)
GEO 0A UCP (UPPER CORNER PIN)
GEO 0B LCP (LOWER CORNER PIN)
– 37 –
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
RM-952
SECTION 5
DIAGRAM
5-1. BLOCK DIAGRAM
MAIN. TUVIF
TU101
BTF-LG433(I)
<slave: C0H>
TV V in
TV L in
TV R in
SP ASSY
AUDIO OUT
IC201
TA8223K
AUDIO
PROSESSOR
IC203
TDA7429S
COMB FILTER
(Glass Combs)
<slave: 80H>
CN304
V1 out
COMB Y in
COMB C in
9
Mon out
TV V in
JACK BLOCK
J401 6P
V1 V in
VIDEO IN 1
V1 R in
RED OUT
43
V1 V in
YC JUNGLE
IC301
CXA2130S
R out
STV5112
Q704-712
6
12
V1 L in
CRT SOCKET
22 R out
7
23 G out
GREEN OUT
G out
24 B out
BLUE OUT
B out
DY
Y21RSA-S
<slave:88H>
NECK ASSY
IK in
21
C3(KV-HF21M50)/C5(KV-XF21M80)
H. DRIVE H-DRIVE
19
Q506
2SC2688
E/W
11
3P
V2 V in
VIDEO IN 2
(FRONT)
V2 L in
V2 V in
HDT
T501
PIN-CONT
IC502
NJM2903D
VM1
H-OUT
Q511
2SC4927
H. PULSE
18
PIN-OUT
Q505
IRF614
PMC
L509
VD+
13
V2 R in
HLC
L510
15
28 29 30 31
VM out
Y in
V in
Y out
U out
V out
37 39 40
R G B
BLK
5V REG & RESET
IC002 MM1319AF
STB TRANS
T604
STB SW TR
Q605
2SK2845
V out 2
L out 2
+B
Additional
Color Matrix
R out 2
DGC
Audio Front Vcc
SYSTEM
Ucom
IC001
CXP86441
– 39 –
FBT
T503
NX-1748
V-OUT
IC503
TDA8172
VD-
14
32 31 30
MONITOR
OUT
VM DRIVE
Q5902/5906
4
U in
J902
CRT
A51LPT70X
– 40 –
SIRCS
I2L
RECEIVER
SBX1981-11
IC901
*+audio 3D Vcc
MEMORY
IC003
ST24C08FB6
(*This is not
+9V
used for
these models)
+5V
SRT
T603
*-audio 3D Vcc
9V REC IC603
5V REC IC604
11V
7V
– 41 –
POWER IC
IC601
STR-F6656
THP
THP600
LINE FILTER
T601
AC CORD
LINE
FILTER
T4601
T4602
F
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
RM-952
E
CN1801
VD + OUT
GND
VD - OUT
15V
N/S ROT
N/S MUTE
PICTURE
TUBE
G2
CN702
1
C3(HF21M50)
1
2
3
4
5
6
C3(HF21M50)
C5(XF21M80)
CN5901
(RGB OUT)
C5(XF21M80)
(RGB OUT)
VM
GND
9V
VM MUTE
GND
NC
+B
CN701
1
1
2
3
CN704
CRT
FBT
5-3. CIRCUIT BOARDS LOCATION
CN1802 (For XF21M80 only)
N/S COIL NC
NS COIL
N/S COIL +
5-2. FRAME SCHEMATIC DIAGRAM
1
2
3
200V
E
H1
CN703
1
2
3
4
5
6
B
G
R
GND
IK
9V
1
2
3
4
5
6
7
VM1
VELOCITY
MODULATION
CN306
VM
GND
9V
VM MUTE
GND
NC
+B
1
2
3
4
5
6
7
H+
H+
HHVV+
1
2
3
4
5
6
DY1
CN604
DY ASSY
1
2
3
1
2
3
F
NECK ASSY
DGC
NC
DGC
200V
GND
H1
CN505
B
G
R
GND
IK
9V
CN305
1
2
3
4
5
6
VD +
GND
VD 15V
N/S ROT
N/S MUTE
1
2
3
4
5
6
1
2
CN507
CN4601
AC IN
AC IN
DGC
VM1
A
F
(POWER SUPPLY, HV, MICON, Y/C JUNGLE)
(CISPR)
– 42 –
AC IN
AC IN
CN601
2
1
1
GND
CN104
1
CN4603
GND
CN4602
AC OUT
AC OUT
1
2
A
– 43 –
– 44 –
KV-HF21M50/XF21M80
RM-952
5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
Note:
• All capacitors are in µF unless otherwise noted.
• All electrolytic capacitors are rated at 50V unless otherwise noted.
• All resistors are in ohms.
kΩ = 1000Ω, MΩ = 1000kΩ
• Indication of resistance which does not have rating electrical
power is as follows.
Pitch: 5 mm
Rating electrical power 1/4W (CHIP: 1/10W)
•
: nonflammable resistor.
•
¢
: internal component.
•
: panel designation or adjustment for repair.
• All variable and adjustable resistors have characteristic curve B unless
otherwise noted.
•
•
•
•
•
•
•
•
•
•
Readings are taken with a color-bar signal input.
no mark : PAL
(
) : SECAM
[
] : NTSC 3.58
«
» : NTSC 4.43
Readings are taken with a 10 MΩ digital multimeter.
Voltage are dc with respect to ground unless otherwise
noted.
Voltage variations may be noted due to normal production
tolerances.
All voltages are in V.
: Cannot be measured.
*
Circled numbers are waveform references.
: B + bus.
: B – bus.
: signal path.
Reference information
RESISTOR
: RN
: RC
: FPRD
: FUSE
: RS
: RB
: RW
:*
COIL
: LF-8L
CAPACITOR
: TA
: PS
: PP
: PT
: MPS
: MPP
: ALB
: ALT
: ALR
METAL FILM
SOLID
NONFLAMMABLE CARBON
NONFLAMMABLE FUSIBLE
NONFLAMMABLE METAL OXIDE
NONFLAMMABLE CEMENT
NONFLAMMABLE WIREWOUND
ADJUSTMENT RESISTOR
MICRO INDUCTOR
TANTALUM
STYROL
POLYPROPYLENE
MYLAR
METALIZED POLYESTER
METALIZED POLYPROPYLENE
BIPOLAR
HIGH TEMPERATURE
HIGH RIPPLE
Note: The component identified by shading and
mark ! are critical for safety. Replace only with
part number specified.
– 45 –
KV-HF21M50/XF21M80
RM-952
A BOARD WAVEFORMS
1
2
3
4 PAL
4 SECAM
4.5Vp-p (V)
3.8Vp-p (V)
3.7Vp-p (V)
1.1Vp-p (H)
1.3Vp-p (H)
4 NTSC 3.58
4 NTSC 4.43
5 PAL/NTSC 3.58
5 SECAM/NTSC 4.43
6
1.2Vp-p (H)
0.8Vp-p (H)
PAL : 0.9Vp-p (V)
NTSC 3.58 : 0.6Vp-p (V)
1.0Vp-p (V)
0.8Vp-p (H)
7 PAL
7 SECAM
7 NTSC 3.58
7 NTSC 4.43
8 PAL
1.1Vp-p (H)
1.0Vp-p (H)
0.7Vp-p (H)
8 SECAM
8 NTSC
9
1.1Vp-p (H)
0.8Vp-p (H)
0.8Vp-p (H)
11
3.1Vp-p (H)
13 NTSC 4.43
0.9Vp-p (H)
12 PAL/NTSC 3.58
3.0Vp-p (H)
14
125Vp-p
1.2Vp-p (H)
10 PAL/NTSC
PAL : 2.7Vp-p (H)
NTSC : 2.8Vp-p (H)
12 SECAM
12 NTSC 4.43
3.0Vp-p (H)
3.1Vp-p (H)
15
16
920Vp-p
1.4Vp-p (V)
– 46 –
1.1Vp-p (H)
10 SECAM
0.8Vp-p (H)
13 PAL/SECAM/NTSC 3.58
1.0Vp-p (H)
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
RM-952
A BOARD IC001 CXP86449-622S (KV-XF21M80)
A BOARD IC001 CXP86449-623S (KV-HF21M50)
TEX
TX
EXTAL
XTAL
RST
MP
VDD
VSS
TO
8-BIT TIMER 1
XLC
EXLC
R
G
B
I
YS
YM
HSYNC
VSYNC
HS0
PORT A
8-BIT TIMER/
COUNTER 0
8
PB0~PB7
6
PC0~PC5
2
2
PC6~PC7
8
PD0~PD7
2
PE0~PE1
2
PE2~PE3
3
PE4~PE6
8
PF0~PF7
5
PG3~PG6*, PG7
PORT D
EC
RAM
352/704/1536 BYTES
PA0~PA7
PORT B
SERIAL INTERFACE
UNIT
ROM
12K/16K/24K/32K
40K/48K/60K BYTES
8
PORT C
FIFO
CLOCK GENERATOR
/SYSTEM CONTROL
2
PRESCALER/
TIME-BASE TIMER
ON SCREEN
DISPLAY
PORT E
S1
SO
SCK
REMOCON
SPC700 CPU CORE
PORT F
RMC
A/D CONVERTER
6CH
IC
PORT G
INT0
INT1
INT2
6
INTERRUPT CONTROLLER
AN0~AN5
A BOARD
WATCHDOG TMER
32kHZ
TIMER/COUNTER
HSYNC COUNTER 0
2
HS1
I2C BUS
INTERFACE UNIT
HSYNC COUNTER 1
8-BIT PWM 8CH
(6CH)
14BIT PWM 1CH
PWM
PWM0~PWM7
(PWM0~PWM5)
ADJ
SCL1
SCL0
SDA1
SDA0
8 (6)
A BOARD ✽ MARK LIST
C003
C202
C203
C204
C205
C206
C207
C323
C329
CN507
CP301
D320
D321
D401
D402
D403
D404
D405
D406
D901
D902
D903
D904
D905
IC001
IC901
KV-HF21M50
100P :CHIP
0.0082 :CHIP
0.0082 :CHIP
0.0033 :PP
0.0033 :CHIP
0.0033 :CHIP
0.033 :PP
#
#
#
#
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
UDZS-TE17-9.1B
CXP86449-623S
SBX1981-51
KV-XF21M80
#
0.01 :CHIP
0.01 :CHIP
0.082 :PP
0.0047 :CHIP
0.0047 :CHIP
0.082 :PP
22
22
4P
COMB FILTER BLOCK
#
#
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
RD9.1S-B
CXP86449-622S
SBX1981-11
Q003
Q004
Q205
Q206
Q207
Q315
Q511
Q603
Q901
Q902
R003
R203
R204
R205
R206
R208
R209
R210
R212
R230
R346
R347
R622
KV-HF21M50
UN2111
UN2111
UN2213
UN2213
UN2213
UN2213
2SD2578-CA
UN2111
UN2213
UN2213
0 :CHIP
3.9K :CHIP
3.3K :CHIP
3.3K :CHIP
3.9K :CHIP
3.3K :CHIP
3.3K :CHIP
120 :CHIP
120 :CHIP
3.3K :CHIP
#
#
33 3W :RS
KV-XF21M80
DTA114EKA-T146
DTC114EK
TR DTC144EKA
TR DTC144EKA
TR DTC144EKA
TR DTC144EKA
2SC4927-01
DTA114EKA-T146
TR DTC144EKA
TR DTC144EKA
10K :CHIP
2.2K :CHIP
6.8K :CHIP
6.8K :CHIP
2.2K :CHIP
6.8K :CHIP
6.8K :CHIP
150 :CHIP
150 :CHIP
6.8K :CHIP
1.2K :CHIP
1.2K :CHIP
8.2 3W :RS
Note) The parts indicated as “#” in this circuit diagram are not listed
here, as they are not used for these models.
NOTE:
The circuit indicated at left contains high voltage of over
600 Vp-p. Please pay attention when inspecting or repairing it to prevent an electric shock.
IC001
IC002
IC003
IC100
IC201
IC203
IC204
IC301
IC502
IC503
IC601
IC602
IC603
IC604
IC901
PH600
B-10
C-9
A-9
B-5
B-11
C-3
B-2
B-6
E-6
J-5
I-8
H-6
D-8
D-10
I-13
H-7
TRANSISTOR
Q001
Q002
Q003
Q004
Q101
Q201
Q202
Q203
Q204
Q205
Q206
Q207
Q301
Q302
Q303
Q304
Q305
Q306
Q307
Q308
Q309
Q310
Q311
Q312
Q313
Q315
Q401
Q402
Q403
Q404
Q501
Q502
Q503
Q505
Q506
Q507
Q509
Q511
Q600
Q601
Q602
Q603
Q604
Q605
Q606
Q607
Q901
Q902
B-8
B-8
C-9
C-9
A-4
A-11
A-11
C-11
C-11
A-12
A-11
A-11
B-8
A-6
A-6
B-6
B-5
B-5
C-7
C-7
C-7
D-7
D-9
B-7
B-8
B-5
D-2
D-1
D-2
C-3
D-6
E-7
F-6
D-6
D-2
H-6
F-6
F-1
C-12
F-11
J-7
I-7
H-6
E-12
F-11
H-13
H-13
H-13
DIODE
D001
D002
D003
B-8
C-8
C-9
D004
D005
D006
D203
D300
D301
D302
D303
D304
D305
D306
D307
D308
D309
D310
D311
D312
D313
D315
D316
D317
D314
D319
D320
D321
D401
D402
D403
D404
D405
D406
D407
D408
D409
D504
D505
D506
D507
D508
D509
D510
D511
D512
D513
D517
D518
D519
D520
D521
D522
D525
D526
D527
D528
D529
D530
D531
D532
D533
D534
D600
D601
D602
D603
D604
D605
D606
D607
D608
D609
D610
D611
D612
D613
D-8
B-8
A-3
C-11
A-9
B-9
B-6
B-5
B-5
B-5
C-5
C-5
B-5
B-6
A-6
C-6
C-6
A-8
B-7
C-7
B-9
A-9
C-6
C-6
B-6
D-2
C-3
B-1
C-2
C-1
B-1
C-2
C-1
A-1
D-5
H-6
F-6
F-6
I-5
E-6
F-5
F-5
G-5
I-5
F-2
F-2
F-2
E-5
I-4
J-4
F-5
F-6
F-3
F-3
F-5
F-2
E-6
E-6
D-2
E-6
G-13
I-8
G-13
F-11
J-7
G-10
E-11
F-10
E-11
H-8
J-8
I-7
F-8
I-7
D614
D615
D616
D617
D618
D620
D621
D622
D623
D624
D625
D627
D628
D629
D630
D631
D632
D633
D634
D635
D636
D637
D638
D901
D902
D903
D904
D905
D906
H-7
E-7
E-9
F-8
F-9
D-8
F-8
F-7
F-12
F-12
D-12
F-8
G-5
F-9
E-9
G-12
F-12
E-12
F-11
F-12
D-12
F-11
E-11
C-13
D-13
C-13
D-13
F-13
I-13
A
PRINTED WIRING BOARD
[POWER SUPPLY, HV, MICON, Y/C JUNGLE]
– A Board –
1
2
3
4
5
6
7
8
9
10
11
12
13
A
B
C
D
E
F
G
H
I
J
Schematic diagrams
– 53 –
– 54 –
– 55 –
C3 C5
boards /
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
RM-952
(3) Schematic Diagrams of C3 and C5 boards
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
(KV-XF21M80)
(KV-HF21M50)
A
B
C
D
D
E
F
G
H
I
– 56 –
– 57 –
– 58 –
20
21
22
PRINTED WIRING BOARDS
C3
[RGB OUT]
C5
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
[RGB OUT]
– C3 Board –
– C5 Board –
C3 BOARD WAVEFORMS
C5 BOARD WAVEFORMS
1
2 PAL
2 SECAM
1
2
3 PAL/SECAM
112Vp-p (H)
25Vp-p (H)
89Vp-p (H)
90Vp-p (H)
126Vp-p (H)
2 NTSC 3.58
2 NTSC 4.43
3
3 NTSC
4
80Vp-p (H)
93Vp-p (H)
PAL/SECAM : 95Vp-p (H)
NTSC : 86Vp-p (H)
110Vp-p (H)
30Vp-p (H)
122Vp-p (H)
4
75Vp-p (H)
– 59 –
– 60 –
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
(4) Schematic Diagrams of VM1 and F boards
1
2
3
4
5
6
7
8
9
10
11
12
A
B
C
D
D
NECK ASSY
E
F
G
VM1
(VELOCITY MODULATION)
H
Schematic diagrams
F VM1
boards /
– 61 –
– 62 –
13
14
VM1
[VELOCITY MODULATION]
F
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
[CISPR]
PRINTED WIRING BOARDS
– F Board –
– VM1 Board –
– 63 –
– 64 –
KV-HF21M50/XF21M80
KV-HF21M50/XF21M80
RM-952
RM-952
5-5. SEMICONDUCTORS
DIODE
IC
TRANSISTOR
AK04V0
AU-01Z-V1
EL1Z
ERA22-08
GP08D
RD33EB3T
RGP02-17EL-6433
CATHODE
D1NS4
D1N20R
RD20ES-B2
RD30ESB2
RD39ES-B2
RD6.8ES-B1
RD9.1ES-L2
1SS119-25
11EFS2
11EQS04
11ES2-NTA2B
5P-6M
CATHODE
GATE
DTA114EKA-T146
DTC114EK
UN2111
UN2211
UN2213
UN2216
2SA1162-G
2SC2712-YG
2SD2114K
2SC4927-01
G1
S1
NC
S2
G2 D2
1
C
ANODE
STR-F6654
TR DTC144EKA
2SA1175-HFE
2SC2785-HFE
E C
B
1
Zig-zag In -line Package
Pin 6~99
IRF614
ANODE
(GRN)
CATHODE
ANODE
(GRN)
1
E C
B
TA8223K
TOP VIEW
Single In -line Package
Pin 6~98
2SA1091-O
G
ERC04-06SE
ERC06-15S
RS3FS
RU-1P
31DQ06-FC5
MARKING SIDE VIEW
MM1319AFBE (7PIN)
NJM2903M (8PIN)
LETTER SIDE
DTZ10B
DTZ-TT11-15B
MA111
UDZS-TE17-6.8B
UDZS-TE17-5.1B
UDZS-TE17.9B
RD10S-B
RD5.1SB-T2
RD9.1S-B
1SS355
TOP VIEW
Dual In-line Package
Pin 6~98
E
L204
******
SPB-26MVWF
ANODE
2SD774-34
B
LED
TDA8172
D1
ANODE
CATHODE
D4SB60L
CXA2130S (64PIN)
CXP86449-622S (64PIN)
CXP86449-623S (64PIN)
ST24C08FB6 (8PIN)
TDA7429S (42 PIN)
D S
2SK2845-LB102
NJM78M09FA
TA7805S
1
ANODE
CATHODE
15
E C
B
CATHODE
2SA1606-E
2SA1837
2SC4159
2SC4793
DA204K
3
LA6510
E
B
C
2SD2578-CA
2
SBX1981-11(12)
1
1
ANODE
3
10
2
1
ERD29-08J
B
FMU-G26S
C E
CATHODE
2SC2458-YGR
2SD2144S-UVW
SE-135N
ANODE
1
2
3
1
2
ON3171-R
E
3
4
3
C B
2SC2611
EG01CV0
LETTER SIDE
CATHODE
1
4
3
1
2
ANODE
E
– 65 –
C B
– 66 –
○
○
○
KV-HF21M50/XF21M80
○
KV-HF21M50/XF21M80
○
RM-952
○
RM-952
○
○
○
SECTION 6
○
Items marked " * " are not stocked since
they are seldom required for routine
service. Some delay should be
anticipated when ordering these items.
○
○
○
○
○
○
The components identified by
shading and mark ! are critical
for safety.
Replace only with part number
specified.
○
○
•
○
NOTE:
• Items with no part number and no description are not stocked because they
are seldom required for routine service.
• The construction parts of an assembled
part are indicated with a collation
number in the remark column.
○
○
○
EXPLODED VIEWS
○
6-1. CHASSIS (KV-XF21M80)
○
REF. NO.
PART NO.
DESCRIPTION
REMARK
○
8 : BVTP3 × 12 7-685-648-79
L : BVTP4 × 16 7-685-663-71
○
(KV-XF21M80)
X-4036-849-2
4-047-464-01
4-067-183-01
4-036-405-11
4-067-181-01
BEZNET ASSY
CATCHER, PUSH
BUTTON, POWER
SPRING, COMPRESSION
BUTTON, MULTI
2-6, 39
○
○
○
○
○
○
○
1
2
3
4
5
○
○
6
7
8
9
10
○
○
34
○
○
38
GUIDE, LIGHT
SPEAKER (13X7CM)
CUSHION, SPEAKER(S)
SCREW (WASHER HEAD) (+P 4X16)
SCREW (5), TAPPING
○
○
27
* 4-067-180-01
1-529-125-11
* 4-069-797-31
4-302-404-03
4-365-808-01
○
31
12
○
r
○
9
○
28
○
24 33
17
○
37
18
○
10
16
○
29
11
○
35
○
7
15
4-046-600-11 SPACER, DY
* 3-704-372-41 HOLDER, HV CABLE
! 8-738-809-05 PICTURE TUBE (A51LPT70X) (KV-XF21M80)
8-451-505-11 DEFLECTION YOKE (Y21RSA-S)
* A-1331-948-A C5 BOARD, MOUNTED
16
17
18
19
20
!
!
*
*
4-369-318-61
1-416-946-11
X-4036-465-2
4-070-139-01
4-070-138-01
SPRING, TENSION
COIL, DEMAGNETIC
COVER ASSY, REAR
PWB(L), GUIDE
PWB(R), GUIDE
○
○
○
L
8
11
12
13
14
15
○
○
25
L
r
26
○
○
○
14
13
r
5
21
22
○
16
36
○
30
○
○
10
23
24
25
26
22
○
○
r
35
23
27
28
29
30
! 1-574-062-52 CORD, POWER (WITH CONNECTOR) 2.5A/
250V
1-452-032-00 MAGNET,DISC
4-051-736-41 PIECE A(90), CONV, CORRECT
* A-1342-488-A VM1 BOARD, MOUNTED
* 4-070-140-11 BRACKET, TERMINAL
○
○
○
21
○
○
○
6
2
○
○
○
33
9
8-598-449-10 TUNER, FSS BTF-LG433
! 1-453-293-11 TRANSFORMER ASSY, FLYBACK (NX-1748//
M3A4)
* A-1298-983-A A BOARD, COMPLETE
4-057-714-01 PIECE ASSY, TLH CORRECTION
! 4-022-115-21 HOLDER, AC CORD
○
4
○
19
CIRCULAR DISC MAGNET B
F BOARD, MOUNTED
NA299-S2
HOLDER, DGC
BAFFLE, SPEAKER
36
37
38
39
1-452-728-41
4-069-652-51
4-069-653-51
4-067-185-01
COIL, NA ROTATION (RT-154)
CUSHION (HS BAND)
CUSHION, DGC
DOOR, CONTROL
20
○
– 67 –
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
1
○
○
7
1-452-094-00
* A-1241-372-A
8-453-011-31
4-064-883-11
4-070-142-01
○
8
3
○
39
31
32
33
34
35
– 68 –
○
○
○
KV-HF21M50/XF21M80
○
KV-HF21M50/XF21M80
○
RM-952
○
○
○
○
○
○
RM-952
○
6-2. CHASSIS (KV-HF21M50)
○
○
○
○
○
○
○
○
○
○
○
8 : BVTP3 × 12 7-685-648-79
L : BVTP4 × 16 7-685-663-71
PART NO.
DESCRIPTION
REMARK
○
○
REF. NO.
○
(KV-HF21M50)
6
7
8
9
10
○
○
○
34
○
26
○
39
○
30
○
○
27
○
17
○
8
14
○
r
○
7
24
L
○
13
25
○
12
○
29
○
○
9
* 3-704-372-11 HOLDER, HV CABLE
! 8-738-812-05 PICTURE TUBE (A51LPT70X)
8-451-505-11 DEFLECTION YOKE (Y21RSA-S)
* A-1331-884-A C3 BOARD, MOUNTED
4-369-318-61 SPRING, TENSION
16
17
18
19
20
!
!
*
*
21
! 1-453-293-11 TRANSFORMER ASSY, FLYBACK (NX-1748//
M3A4)
* A-1299-015-A A BOARD, COMPLETE
4-057-714-01 PIECE ASSY, TLH CORRECTION
4-022-115-12 HOLDER, AC CORD
! 1-574-062-52 CORD, POWER (WITH CONNECTOR) 2.5A/
250V
22
23
24
25
○
○
32
21
○
○
○
32
1-416-946-11
X-4036-465-2
4-070-189-01
4-070-187-01
8-598-449-10
COIL, DEMAGNETIC
COVER ASSY, REAR
PWB(L), GUIDE
PWB(R), GUIDE
TUNER, FSS BTF-LG433
22
26
27
28
29
30
1-452-032-00
4-051-736-41
* A-1342-453-A
* 4-067-167-11
1-452-094-00
MAGNET,DISC
PIECE A(90), CONV, CORRECT
VM1 BOARD, MOUNTED
BRACKET, TERMINAL
CIRCULAR DISC MAGNET B
31
32
33
34
35
4-069-651-02
* A-1241-355-A
8-453-011-31
4-064-883-11
4-069-652-02
BLOTTING SHEET
F BOARD, MOUNTED
NA299-S2
HOLDER, DGC
CUSHION (HS BAND)
36
37
38
39
4-067-191-01
4-067-193-01
4-067-192-91
4-054-981-01
○
○
○
20
○
2
○
○
○
39
8
3
○
18
○
○
○
– 69 –
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
19
1
○
36
38
6
7
○
4
○
37
GUIDE, LIGHT
SPEAKER (15X6.5 CM)
CUSHION, SPEAKER
SCREW (5), TAPPING
SPACER, DY
11
12
13
14
15
○
5
4-067-197-01
1-503-902-11
* 4-379-189-11
4-365-808-01
4-046-600-11
○
○
○
15
r
2-6, 36,37
○
16
○
35
23 33
○
○
9
15
○
28
10
BEZNET ASSY
CATCHER, PUSH
BUTTON, POWER
SPRING, COMPRESSION
BUTTON, MULTI
○
11
r
X-4036-989-1
4-047-464-01
4-067-190-01
4-036-405-11
4-067-196-01
○
○
○
○
○
○
○
1
2
3
4
5
– 70 –
PANEL (R)
PANEL (L)
DOOR, CONTROL
SCREW, STEP TAPPING
KV-HF21M50/XF21M80
SECTION 7
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
NOTE:
RM-952
ELECTRICAL PARTS LIST
DESCRIPTION
REMARK
REF. NO. PART NO.
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
• Items marked " ∗ " are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
When indicating parts by reference
number, please include the board name.
• All variable and adjustable resistors have
characteristic curve B, unless otherwise
noted.
REF.NO. PART NO.
DESCRIPTION
REMARK
* A-1299-015-A A BOARD, COMPLETE (KV-HF21M50)
********************
* A-1298-983-A A BOARD, COMPLETE (KV-XF21M80)
********************
X-4036-448-3
X-4036-449-3
X-4036-450-3
* 4-040-983-41
* 4-055-304-01
HEAT SINK ASSY (KV-XF21M80 ONLY)
HEAT SINK ASSY (KV-XF21M80 ONLY)
HEAT SINK ASSY (KV-XF21M80 ONLY)
TERMINAL BOARD (D) (KV-XF21M80 ONLY)
HOLDER, LED
4-066-910-61
4-066-911-61
4-066-912-61
* 4-067-182-02
* 4-070-141-01
HEAT SINK (KV-XF21M80 ONLY)
HEAT SINK (KV-XF21M80 ONLY)
HEAT SINK (KV-XF21M80 ONLY)
HOLDER, FBT (KV-HF21M50)
HOLDER, FBT (KV-XF21M80)
4-382-854-11
4-382-854-21
7-685-648-79
SCREW (M3X10), P, SW (+)
SCREW (M3X14), P, SW (+)
SCREW +BVTP 3X12 TYPE2 N-S
<CAPACITOR>
C003
1-163-251-11
C004
C005
C006
C007
REF.NO. PART NO.
REMARK
• All resistors are in ohms
• F : nonflammable
CAPACITORS
• MF : µF, PF : µµF
COILS
• MMH : mH, UH : µH
DESCRIPTION
REMARK
C042
C043
C044
C047
C048
1-163-251-11
1-163-251-11
1-163-251-11
1-163-251-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C050
C051
C053
C054
C055
1-163-251-11
1-163-251-11
1-163-251-11
1-163-251-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C103
C104
C107
C108
C109
1-164-004-51
1-126-933-11
1-163-005-51
1-126-933-11
1-163-005-51
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1MF
100MF
470PF
100MF
470PF
10%
20%
10%
20%
10%
25V
16V
50V
16V
50V
C110
C111
C112
C113
C114
1-163-005-51
1-163-005-51
1-126-933-11
1-126-967-11
1-126-967-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
470PF
470PF
100MF
47MF
47MF
10%
10%
20%
20%
20%
50V
50V
16V
50V
50V
CERAMIC CHIP
(KV-HF21M50)
CERAMIC CHIP
(KV-XF21M80)
CERAMIC CHIP
(KV-HF21M50)
CERAMIC CHIP
(KV-XF21M80)
FILM
(KV-HF21M50)
0.0082MF
10%
50V
0.01MF
10%
50V
0.0082MF
10%
50V
0.01MF
10%
50V
0.033MF
5%
50V
FILM
(KV-XF21M80)
CERAMIC CHIP
(KV-HF21M50)
CERAMIC CHIP
(KV-XF21M80)
CERAMIC CHIP
(KV-HF21M50)
CERAMIC CHIP
(KV-XF21M80)
0.082MF
5%
50V
0.0033MF
10%
50V
0.0047MF
10%
50V
0.0033MF
10%
50V
0.0047MF
10%
50V
0.033MF
5%
50V
0.082MF
5%
50V
10MF
10MF
100MF
20%
20%
20%
50V
50V
16V
470MF
100MF
20%
20%
25V
16V
5%
50V
C202
1-163-020-00
1-163-001-51
1-163-001-51
1-164-004-51
1-126-933-11
CERAMIC CHIP 100PF
(KV-HF21M50 ONLY)
CERAMIC CHIP 220PF
CERAMIC CHIP 220PF
CERAMIC CHIP 0.1MF
ELECT
100MF
10%
10%
10%
20%
50V
50V
25V
16V
C202
1-164-232-11
C203
1-163-020-00
C203
1-164-232-11
C008
C010
C012
C013
C014
1-163-251-11
1-163-251-11
1-163-251-11
1-164-232-11
1-126-967-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
100PF
100PF
0.01MF
47MF
5%
5%
5%
10%
20%
50V
50V
50V
50V
50V
C204
1-136-159-00
C204
1-136-164-00
C015
C016
C017
C019
C022
1-163-009-11
1-163-113-00
1-163-113-00
1-104-665-11
1-163-227-51
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.001MF
68PF
68PF
100MF
10PF
10%
10%
10%
20%
0.5PF
50V
50V
50V
25V
50V
C205
1-164-182-11
C205
1-163-017-00
C206
1-164-182-11
C023
C024
C026
C027
C028
1-163-227-51
1-163-227-51
1-164-004-51
1-164-004-51
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
10PF
0.1MF
0.1MF
0.022MF
0.5PF
0.5PF
10%
10%
10%
50V
50V
25V
25V
50V
C206
1-163-017-00
C207
1-136-159-00
C207
1-136-164-00
C030
C031
C032
C034
C041
1-126-965-11
1-164-004-51
1-107-823-51
1-163-031-11
1-163-251-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22MF
0.1MF
000000000
0.01MF
100PF
20%
10%
10%
50V
25V
16V
50V
50V
C208
C209
C210
1-125-797-91
1-125-797-91
1-126-933-11
FILM
(KV-HF21M50)
FILM
(KV-XF21M80)
ELECT
ELECT
ELECT
C211
C212
1-126-941-11
1-126-933-11
ELECT
ELECT
5%
A
DESCRIPTION
– 71 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
A
REF. NO. PART NO.
DESCRIPTION
REMARK
C213
C214
C215
1-126-933-11
1-126-942-61
1-126-942-61
ELECT
ELECT
ELECT
100MF
1000MF
1000MF
20%
20%
20%
16V
25V
25V
C216
C217
C218
C219
C220
1-164-232-11
1-125-797-91
1-136-167-00
1-136-167-00
1-126-942-61
CERAMIC CHIP
ELECT
FILM
FILM
ELECT
0.01MF
10MF
0.15MF
0.15MF
1000MF
10%
20%
5%
5%
20%
50V
50V
50V
50V
25V
C221
C223
C224
C225
C226
1-125-797-91
1-126-965-11
1-163-133-00
1-109-982-51
1-109-982-51
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10MF
22MF
470PF
1MF
1MF
20%
20%
10%
10%
10%
50V
50V
50V
10V
10V
C227
C228
C229
C230
C231
1-163-037-11
1-163-024-00
1-163-018-00
1-163-024-00
1-163-018-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022MF
0.018MF
0.0056MF
0.018MF
0.0056MF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C232
C233
C234
C235
C236
1-163-037-11
1-164-004-51
1-164-004-51
1-164-004-51
1-164-004-51
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022MF
0.1MF
0.1MF
0.1MF
0.1MF
10%
10%
10%
10%
10%
50V
25V
25V
25V
25V
C238
C240
C241
C242
C243
1-164-505-51
1-164-505-51
1-164-346-51
1-164-505-51
1-216-295-61
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
SHORT CHIP
2.2MF
2.2MF
1MF
2.2MF
0
10%
10%
10%
10%
16V
16V
16V
16V
C244
C245
C246
C247
C248
1-164-700-51
1-164-346-51
1-163-018-00
1-164-346-51
1-163-010-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.68MF
1MF
0.0056MF
1MF
0.0012MF
C249
C250
C251
C252
C253
1-164-004-51
1-216-295-61
1-163-017-00
1-164-346-51
1-163-037-11
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C254
C255
C256
C259
C264
1-126-965-11
1-163-037-11
1-164-004-51
1-126-933-11
1-164-505-51
C265
C301
C302
C303
C304
10%
10%
10%
10%
16V
16V
50V
16V
50V
0.1MF
0
0.0047MF
1MF
0.022MF
10%
25V
10%
10%
10%
50V
16V
50V
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
22MF
0.022MF
0.1MF
100MF
2.2MF
20%
10%
10%
20%
10%
50V
50V
25V
16V
16V
1-164-505-51
1-126-935-11
1-163-005-51
1-125-797-91
1-126-967-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
2.2MF
470MF
470PF
10MF
47MF
10%
20%
10%
20%
20%
16V
16V
50V
50V
50V
C305
C306
C307
C308
C309
1-164-004-51
1-163-233-51
1-163-233-51
1-163-125-00
1-126-957-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1MF
18PF
18PF
220PF
0.22MF
10%
5%
5%
5%
20%
25V
50V
50V
50V
50V
C310
C311
C312
C313
C315
1-125-805-91
1-125-797-91
1-164-346-51
1-164-346-51
1-164-004-51
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7MF
10MF
1MF
1MF
0.1MF
20%
20%
10%
10%
10%
50V
50V
16V
16V
25V
REF. NO. PART NO.
DESCRIPTION
REMARK
C316
C317
C318
C319
C320
1-126-967-11
1-164-004-51
1-163-031-11
1-163-031-11
1-163-031-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47MF
0.1MF
0.01MF
0.01MF
0.01MF
C322
C323
1-163-005-51
1-126-965-11
C324
C325
C327
1-163-017-00
1-125-799-91
1-126-965-11
CERAMIC CHIP 470PF
ELECT
22MF
(KV-XF21M80 ONLY)
CERAMIC CHIP 0.0047MF
ELECT
1MF
ELECT
22MF
C328
C329
1-164-004-51
1-126-965-11
C330
C331
C332
20%
10%
50V
25V
50V
50V
50V
10%
20%
50V
50V
10%
20%
20%
50V
63V
50V
10%
20%
25V
50V
1-164-004-51
1-220-948-91
1-125-805-91
CERAMIC CHIP 0.1MF
ELECT
22MF
(KV-XF21M80 ONLY)
CERAMIC CHIP 0.1MF
METAL
100
ELECT
4.7MF
10%
5%
20%
25V
1/2W
50V
C335
C336
C337
C338
C341
1-164-004-51
1-164-004-51
1-125-800-91
1-163-017-00
1-115-340-51
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1MF
0.1MF
2.2MF
0.0047MF
0.22MF
10%
10%
20%
10%
10%
25V
25V
63V
50V
25V
C342
C401
C402
C403
C404
1-163-125-00
1-164-346-51
1-164-346-51
1-163-005-51
1-163-005-51
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
1MF
1MF
470PF
470PF
5%
10%
10%
10%
10%
50V
16V
16V
50V
50V
C405
C406
C407
C408
C409
1-126-935-11
1-164-346-51
1-164-346-51
1-163-133-00
1-125-805-91
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
470MF
1MF
1MF
470PF
4.7MF
20%
10%
10%
10%
20%
16V
16V
16V
50V
50V
C415
C502
C506
C507
C510
1-163-133-00
1-163-145-00
1-107-638-11
1-161-830-00
1-102-112-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC
CERAMIC
470PF
0.0015MF
33MF
0.0047MF
330PF
10%
5%
20%
10%
50V
50V
160V
500V
50V
C513
C514
C517
C518
C519
1-163-263-51
1-106-383-00
1-164-182-11
1-126-933-11
1-102-212-00
CERAMIC CHIP
MYLAR
CERAMIC CHIP
ELECT
CERAMIC
330PF
0.047MF
3300PF
100MF
820PF
10%
10%
10%
20%
10%
50V
200V
50V
16V
500V
C521
C522
C523
C524
C526
1-104-666-11
1-126-933-11
1-102-002-00
1-126-967-11
1-130-495-00
ELECT
ELECT
CERAMIC
ELECT
MYLAR
220MF
100MF
680PF
47MF
0.1MF
20%
20%
10%
20%
5%
25V
16V
500V
50V
50V
C527
C528
C530
C531
C532
1-102-820-00
1-162-134-11
1-137-372-11
1-109-953-11
1-128-528-11
CERAMIC
CERAMIC
FILM
ELECT
ELECT
330PF
470PF
0.022MF
2.2MF
470MF
5%
10%
5%
20%
20%
50V
2KV
50V
50V
25V
C533
C536
C537
C538
C539
1-128-528-11
1-136-165-00
1-107-911-11
1-136-076-00
1-129-746-91
ELECT
FILM
ELECT
FILM
FILM
470MF
0.1MF
220MF
0.0085MF
0.039MF
20%
5%
20%
3%
5%
25V
50V
50V
2KV
400V
– 72 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
A
DESCRIPTION
REMARK
C540
C546
C549
C550
C551
1-136-171-00
1-165-319-11
1-163-017-00
1-106-220-00
1-125-799-91
FILM
CERAMIC CHIP
CERAMIC CHIP
MYLAR
ELECT
0.33MF
0.1MF
0.0047MF
0.1MF
1MF
10%
10%
20%
50V
50V
50V
100V
63V
C552
C553
C554
C556
C557
1-162-116-00
1-162-116-00
1-137-417-11
1-128-528-11
1-126-941-11
CERAMIC
CERAMIC
MYLAR
ELECT
ELECT
680PF
680PF
0.0047MF
470MF
470MF
10%
10%
10%
20%
20%
2KV
2KV
200V
25V
25V
C558
C560
C561
C562
C564
1-123-024-21
1-102-228-00
1-136-557-11
1-102-228-00
1-163-038-00
ELECT
CERAMIC
FILM
CERAMIC
CERAMIC CHIP
33MF
470PF
0.0033MF
470PF
0.1MF
10%
5%
10%
160V
500V
630V
500V
25V
C565
C566
C567
C568
C570
1-107-655-11
1-102-244-00
1-115-521-11
1-102-228-00
1-115-520-11
ELECT
CERAMIC
FILM
CERAMIC
FILM
47MF
220PF
0.82MF
470PF
0.68MF
20%
10%
5%
10%
5%
250V
500V
250V
500V
250V
C573
C574
C577
C582
C600 !
1-106-379-12
1-107-636-11
1-106-395-00
1-164-004-51
1-104-705-51
MYLAR
ELECT
MYLAR
CERAMIC CHIP
FILM
0.033MF
10MF
0.15MF
0.1MF
0.1MF
10%
20%
10%
10%
20%
200V
160V
200V
25V
250V
C602
1-104-704-51
C604
1-163-009-11
C605 ! 1-127-942-51
C606 ! 1-127-942-51
C607
1-161-830-00
FILM
CERAMIC CHIP
CERAMIC
CERAMIC
CERAMIC
0.1MF
0.001MF
330PF
330PF
0.0047MF
20%
10%
10%
10%
99%
250V
50V
250V
250V
500V
C608
C609
C610
C611
C612
1-161-830-00
1-126-968-11
1-125-797-91
1-161-830-00
1-161-830-00
CERAMIC
ELECT
ELECT
CERAMIC
CERAMIC
C613
C614
C616
C617
C618
1-117-752-11
1-125-797-91
1-130-202-00
1-107-792-11
1-125-893-11
0.0047MF
100MF
10MF
0.0047MF
0.0047MF
5%
99%
20%
20%
99%
99%
500V
50V
50V
500V
500V
ELECT(BLOCK) 330MF
ELECT
10MF
FILM
0.022MF
CERAMIC
100PF
FILM
680PF
20%
20%
10%
5%
3%
450V
50V
400V
1KV
1.5KV
C619 ! 1-119-886-51
C620
1-163-133-00
C621
1-102-114-00
C622
1-102-074-00
C623
1-104-665-11
CERAMIC
CERAMIC CHIP
CERAMIC
CERAMIC
ELECT
470PF
470PF
470PF
0.001MF
100MF
10%
10%
10%
10%
20%
250V
50V
50V
50V
25V
C624
C627
C628
C629
C630
1-104-331-11
1-102-002-00
1-126-942-61
1-125-797-91
1-124-347-00
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
0.0022MF
680PF
1000MF
10MF
100MF
10%
10%
20%
20%
20%
1KV
500V
25V
50V
160V
C633
C634
C635
C636
C639
1-104-999-11
1-126-934-11
1-104-665-11
1-104-760-51
1-164-004-51
MYLAR
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1MF
220MF
100MF
0.047MF
0.1MF
10%
20%
20%
10%
10%
200V
16V
10V
50V
25V
C640
C641
1-164-004-51
1-102-002-00
CERAMIC CHIP
CERAMIC
0.1MF
680PF
10%
10%
25V
500V
REF. NO. PART NO.
DESCRIPTION
REMARK
C642
C643
C644
1-126-943-11
1-126-933-11
1-104-331-11
ELECT
ELECT
CERAMIC
2200MF
100MF
0.0022MF
20%
20%
10%
25V
16V
1KV
C645
C646
C647
C649
C650
1-137-605-11
1-107-679-91
1-163-275-11
1-126-940-11
1-163-275-11
FILM
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01MF
10MF
0.001MF
330MF
0.001MF
10%
20%
5%
20%
5%
250V
450V
50V
25V
50V
C651
C652
C653
C657
C658
1-163-133-00
1-126-965-11
1-126-967-11
1-101-821-00
1-164-004-51
CERAMIC CHIP
ELECT
ELECT
CERAMIC
CERAMIC CHIP
470PF
22MF
47MF
0.0022MF
0.1MF
10%
20%
20%
10%
50V
50V
50V
500V
25V
C901
C902
C905
C906
C907
1-136-153-00
1-136-153-00
1-125-805-91
1-164-346-51
1-163-133-00
FILM
FILM
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01MF
0.01MF
4.7MF
1MF
470PF
5%
5%
20%
10%
10%
50V
50V
50V
16V
50V
C908
C909
C910
C911
C912
1-163-133-00
1-164-346-51
1-126-967-11
1-126-967-11
1-164-004-51
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
470PF
1MF
47MF
47MF
0.1MF
10%
10%
20%
20%
10%
50V
16V
50V
50V
25V
C913
C914
1-126-933-11
1-163-133-00
ELECT
CERAMIC CHIP
100MF
470PF
20%
10%
16V
50V
<CONNECTOR>
CN104
CN202
CN203
CN204
CN305
*
*
*
*
1-695-915-11
1-785-608-11
1-564-506-11
1-564-506-11
1-564-509-11
TAB (CONTACT)
PIN, CONNECTOR 4P
PLUG, CONNECTOR 3P
PLUG, CONNECTOR 3P
PLUG, CONNECTOR 6P
CN306 * 1-564-510-11
CN505 1-508-765-00
CN506 4-352-844-01
CN507 * 1-564-507-11
CN601 * 1-580-843-11
PLUG, CONNECTOR 7P
PIN, CONNECTOR (5MM PITCH) 3P
PIN, LEAD, COATING
PLUG, CONNECTOR 4P (KV-XF21M80 ONLY)
PIN, CONNECTOR (POWER)
CN602
CN604
CN609
CN901
PIN, CONNECTOR (5MM PITCH) 2P
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR (5MM PITCH) 1P
PLUG, CONNECTOR 4P
*
*
*
*
1-508-786-00
1-573-963-11
1-508-784-21
1-564-507-11
<COMPOSITION CIRCUIT BLOCK>
CP301
1-467-554-21
FILTER BLOCK, COMB (KV-XF21M80 ONLY)
<DIODE>
D001
D005
D006
D203
D300
8-719-988-61
8-719-988-61
8-719-988-61
8-719-914-42
1-216-295-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE DA204K
SHORT CHIP
0
D301
D306
D307
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
– 73 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
A
REF. NO. PART NO.
DESCRIPTION
REMARK
D308
D309
8-719-988-61
8-719-159-10
DIODE 1SS355TE-17
DIODE RD5.1SB-T2
D311
D312
D313
D314
D315
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D316
D320
D321
D401
D402
8-719-069-57
8-719-069-60
8-719-069-60
8-719-158-35
8-719-158-35
DIODE UDZS-TE17-6.8B
DIODE UDZS-TE17-9.1B (KV-HF21M50 ONLY)
DIODE UDZS-TE17-9.1B (KV-HF21M50 ONLY)
DIODE RD9.1SB
DIODE RD9.1SB
D403
D404
D405
D406
D504
8-719-158-35
8-719-158-35
8-719-158-35
8-719-158-35
8-719-302-43
DIODE RD9.1SB
DIODE RD9.1SB
DIODE RD9.1SB
DIODE RD9.1SB
DIODE EL1Z
D505
D506
D507
D508
D509
8-719-988-61
8-719-911-19
8-719-988-61
8-719-988-61
1-216-073-61
DIODE 1SS355TE-17
DIODE 1SS119-25
DIODE 1SS355TE-17
DIODE 1SS355TE-17
RES,CHIP
10G
D510
D511
D512
D513
D517
8-719-988-61
8-719-988-61
8-719-988-61
8-719-908-03
8-719-945-80
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE GP08D
DIODE ERC06-15S
D518
D520
D521
D522
D523
8-719-900-26
1-216-295-61
8-719-302-43
8-719-302-43
8-719-302-43
DIODE ERD29-08J
SHORT CHIP
0
DIODE EL1Z
DIODE EL1Z
DIODE EL1Z
D527
D528
D531
D532
D602
8-719-908-03
8-719-908-03
8-719-988-61
8-719-988-61
8-719-911-19
DIODE GP08D
DIODE GP08D
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS119-25
D603
D604
D605
D606
D607
8-719-150-92
8-719-028-72
8-719-510-53
8-719-108-18
8-719-073-01
DIODE RD33EB3T
DIODE RGP02-17EL-6433
DIODE D4SB60L
THYRISTOR 5P6M
DIODE MA111-(K8).S0
D608
D609
D610
D611
D613
8-719-110-53
8-719-311-31
8-719-043-76
8-719-046-74
8-719-046-74
DIODE RD20ESB2
DIODE RU-1P
DIODE AK04V0
DIODE AU-01Z-V1
DIODE AU-01Z-V1
D614
D618
D620
D622
8-719-046-74
8-719-067-18
8-719-110-72
8-719-071-39
D623
D624
D625
D627
D628
8-719-978-65
8-719-073-01
8-719-158-39
8-719-073-84
8-719-911-19
REF. NO. PART NO.
DESCRIPTION
REMARK
D631
D632
D633
D634
D635
8-719-068-00
8-719-068-00
8-719-948-45
8-719-073-01
8-719-073-01
DIODE ERC04-06SE
DIODE ERC04-06SE
DIODE ERA22-08
DIODE MA111-(K8).S0
DIODE MA111-(K8).S0
D636
D637
D638
D901
D901
8-719-510-02
8-719-109-96
8-719-510-48
8-719-069-60
8-719-158-35
DIODE D1NS4
DIODE RD6.8ESB1
DIODE D1N20R
DIODE UDZS-TE17-9.1B (KV-HF21M50)
DIODE RD9.1SB (KV-XF21M80)
D902
D902
D903
D903
D904
8-719-069-60
8-719-158-35
8-719-069-60
8-719-158-35
8-719-069-60
DIODE UDZS-TE17-9.1B (KV-HF21M50)
DIODE RD9.1SB (KV-XF21M80)
DIODE UDZS-TE17-9.1B (KV-HF21M50)
DIODE RD9.1SB (KV-XF21M80)
DIODE UDZS-TE17-9.1B (KV-HF21M50)
D904
D905
D905
D906
8-719-158-35
8-719-069-60
8-719-158-35
8-719-045-19
DIODE RD9.1SB (KV-XF21M80)
DIODE UDZS-TE17-9.1B (KV-HF21M50)
DIODE RD9.1SB (KV-XF21M80)
DIODE SPB-26MVWF
<CONNECTOR>
5%
1/10W
DY1
* 1-580-798-11
CONNECTOR PIN (DY) 6P
<FERRITE BEAD>
FB103
FB501
FB502
FB600
FB601
1-410-397-21
1-410-397-21
1-410-397-21
1-410-397-21
1-410-397-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
1.1UH
1.1UH
1.1UH
1.1UH
1.1UH
FB602
FB603
FB604
FB607
FB608
1-410-397-21
1-410-397-21
1-410-397-21
1-410-397-21
1-412-911-31
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
1.1UH
1.1UH
1.1UH
1.1UH
0UH
FB611
FB613
FB615
1-410-397-21
1-410-397-21
1-410-397-21
FERRITE
FERRITE
FERRITE
1.1UH
1.1UH
1.1UH
<IC>
IC001
IC001
IC002
IC003
IC201
8-752-906-21
8-752-906-20
8-759-371-21
8-759-370-34
8-759-336-30
IC CXP86449-623S (KV-HF21M50)
IC CXP86449-622S (KV-XF21M80)
IC MM1319AFBE
IC ST24C08FB6
IC TA8223K
DIODE AU-01Z-V1
DIODE RN4Z
DIODE RD30ESB2
DIODE FMU-G26S
IC203
IC301
IC502
IC503
IC601
8-759-553-40
8-752-088-39
8-759-700-07
8-759-980-58
8-749-013-75
IC TDA7429S
IC CXA2130S
IC NJM2903M
IC TDA8172
IC STR-F6654
DIODE DTZ-TT11-15B
DIODE MA111-(K8).S0
DIODE RD10SB
DIODE 31DQ06-FC5
DIODE 1SS119-25
IC602
IC603
IC604
IC901
IC901
8-749-920-61
8-759-701-59
8-759-231-53
8-742-041-11
8-742-041-12
IC SE-135N
IC NJM78M09FA
IC TA7805S
HYB IC SBX1981-51 (KV-HF21M50)
HYB IC SBX1981-11 (KV-XF21M80)
– 74 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
A
DESCRIPTION
REMARK
<JACK>
J401
J901
J902
1-779-850-11
1-770-786-11
1-770-329-11
JACK BLOCK, PIN 6P
JACK
JACK, PIN 3P
<CHIP CONDUCTOR>
REF. NO. PART NO.
DESCRIPTION
REMARK
L508
L509
1-412-525-31
1-459-390-00
INDUCTOR
INDUCTOR
10UH
390UH
L510
L512
L513
L515
L518
1-416-972-11
1-412-549-31
1-412-549-31
1-459-104-00
1-408-611-31
COIL, HORIZONTAL LINEARITY
INDUCTOR
1MMH
INDUCTOR
1MMH
COIL, WITH CORE
INDUCTOR
47UH
L601
L901
L902
L905
1-412-527-11
1-408-603-31
1-408-603-31
1-414-856-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
JR002
JR003
JR004
JR005
JR006
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JR007
JR008
JR009
JR010
JR011
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JR012
JR013
JR014
JR015
JR016
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JR018
JR019
JR102
JR109
JR202
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Q002
Q003
Q003
Q004
Q004
8-729-230-49
8-729-424-08
8-729-027-23
8-729-421-22
8-729-900-53
TRANSISTOR 2SC2712-YG
TRANSISTOR UN2111 (KV-HF21M50)
TRANSISTOR DTA114EKA-T146 (KV-XF21M80)
TRANSISTOR UN2211 (KV-HF21M50)
TRANSISTOR DTC114EK (KV-XF21M80)
JR301
JR303
JR401
JR403
JR404
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Q101
Q201
Q202
Q203
Q203
8-729-230-49
8-729-424-67
8-729-424-67
8-729-421-19
1-801-806-11
TRANSISTOR 2SC2712-YG
TRANSISTOR UN2216
TRANSISTOR UN2216
TRANSISTOR UN2213 (KV-HF21M50)
TRANSISTOR DTC144EKA-T146 (KV-XF21M80)
JR405
JR500
JR501
JR600
1-216-295-61
1-216-295-61
1-216-295-61
1-216-295-61
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
Q204
Q204
Q205
Q205
Q206
8-729-026-49
8-729-216-22
8-729-421-19
1-801-806-11
8-729-421-19
TRANSISTOR 2SA1037AK-T146-R
TRANSISTOR 2SA1162-G
TRANSISTOR UN2213 (KV-HF21M50)
TRANSISTOR DTC144EKA-T146 (KV-XF21M80)
TRANSISTOR UN2213 (KV-HF21M50)
Q206
Q207
Q207
Q301
Q302
1-801-806-11
8-729-421-19
1-801-806-11
8-729-216-22
8-729-230-49
TRANSISTOR DTC144EKA-T146 (KV-XF21M80)
TRANSISTOR UN2213 (KV-HF21M50)
TRANSISTOR DTC144EKA-T146 (KV-XF21M80)
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC2712-YG
Q303
Q305
Q306
Q307
Q308
8-729-216-22
8-729-216-22
8-729-216-22
8-729-230-49
8-729-216-22
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC2712-YG
TRANSISTOR 2SA1162-G
Q312
Q313
Q315
Q315
Q401
8-729-216-22
8-729-230-49
8-729-421-19
1-801-806-11
8-729-424-67
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC2712-YG
TRANSISTOR UN2213 (KV-HF21M50)
TRANSISTOR DTC144EK-T146 (KV-XF21M80)
TRANSISTOR UN2216
Q402
Q403
Q404
Q503
Q505
8-729-424-67
8-729-216-22
8-729-216-22
8-729-230-49
8-729-931-45
TRANSISTOR UN2216
TRANSISTOR 2SA1162-G
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC2712-YG
TRANSISTOR IRF614
15UH
10UH
10UH
10UH
<PHOTO COUPLER>
PH600 ! 8-749-924-35
PHOTO COUPLER ON3171-R
<IC LINK>
<COIL>
L002
L003
L005
L101
L102
1-414-856-11
1-414-180-11
1-414-233-22
1-414-856-11
1-414-856-11
INDUCTOR
INDUCTOR
INDUCTOR CHIP
INDUCTOR
INDUCTOR
10UH
3.3UH
0UH
10UH
10UH
L103
L104
L105
L204
L301
1-414-856-11
1-414-856-11
1-414-856-11
1-414-856-11
1-414-189-31
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10UH
10UH
10UH
10UH
100UH
L302
L501
L502
L503
L504
1-414-185-41
1-412-525-31
1-422-613-11
1-412-525-31
1-412-525-31
INDUCTOR
INDUCTOR
COIL, AIR CORE
INDUCTOR
INDUCTOR
22UH
10UH
L505
L506
L507
1-412-525-31
1-412-525-31
1-459-111-00
INDUCTOR
INDUCTOR
INDUCTOR
10UH
10UH
10MMH
10UH
10UH
PS200
1-532-675-21
LINK, IC 1.5A/150V
<TRANSISTOR>
– 75 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
A
REF. NO. PART NO.
DESCRIPTION
REMARK
REF. NO. PART NO.
DESCRIPTION
REMARK
Q506
Q507
Q509
Q511
Q511
8-729-140-96
8-729-216-22
8-729-230-49
8-729-048-07
8-729-016-32
TRANSISTOR 2SD774-34
TRANSISTOR 2SA1162-G
TRANSISTOR 2SC2712-YG
TRANSISTOR 2SD2578-CA (KV-HF21M50)
TRANSISTOR 2SC4927-01 (KV-XF21M80)
R046
R047
R048
R050
R053
1-216-049-61
1-414-233-22
1-216-073-61
1-216-073-61
1-216-049-61
RES,CHIP
INDUCTOR CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
0UH
10G
10G
1K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
Q601
Q602
Q603
Q603
Q604
8-729-023-22
8-729-230-49
8-729-424-08
8-729-027-23
8-729-200-17
TRANSISTOR 2SD2114K
TRANSISTOR 2SC2712-YG
TRANSISTOR UN2111 (KV-HF21M50)
TRANSISTOR DTA114EKA-T146 (KV-XF21M80)
TRANSISTOR 2SA1091-O
R055
R056
R061
R062
R063
1-216-073-61
1-216-073-61
1-216-033-61
1-216-041-61
1-216-037-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10G
10G
220
470
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q605
Q606
Q607
Q608
Q901
8-729-044-30
8-729-230-49
8-729-922-37
8-729-230-49
8-729-421-19
TRANSISTOR 2SK2845-LB102
TRANSISTOR 2SC2712-YG
TRANSISTOR 2SD2144S-UVW
TRANSISTOR 2SC2712-YG
TRANSISTOR UN2213 (KV-HF21M50)
R064
R065
R066
R105
R109
1-216-037-61
1-216-037-61
1-216-049-61
1-216-295-61
1-216-041-61
RES,CHIP
RES,CHIP
RES,CHIP
SHORT CHIP
RES,CHIP
330
330
1K
0
470
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
Q901
Q902
Q902
1-801-806-11
8-729-421-19
1-801-806-11
TRANSISTOR DTC144EKA-T146 (KV-XF21M80)
TRANSISTOR UN2213 (KV-HF21M50)
TRANSISTOR DTC144EKA-T146 (KV-XF21M80)
R111
R112
R113
R202
R203
1-216-025-61
1-216-025-61
1-216-047-00
1-216-053-61
1-216-063-91
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
(KV-HF21M50)
100
100
820
1.5K
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R203
1-216-057-61
2.2K
5%
1/10W
R204
1-216-061-00
3.3K
5%
1/10W
R204
1-216-069-61
6.8K
5%
1/10W
R205
1-216-061-00
3.3K
5%
1/10W
R205
1-216-069-61
RES,CHIP
(KV-XF21M80)
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
6.8K
5%
1/10W
R206
1-216-063-91
3.9K
5%
1/10W
R206
1-216-057-61
2.2K
5%
1/10W
R207
R208
1-216-053-61
1-216-061-00
1.5K
3.3K
5%
5%
1/10W
1/10W
R208
1-216-069-61
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
RES,CHIP
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
6.8K
5%
1/10W
R209
1-216-061-00
3.3K
5%
1/10W
R209
1-216-069-61
6.8K
5%
1/10W
R210
1-216-027-00
120
5%
1/10W
R210
1-216-029-61
150
5%
1/10W
R212
1-216-027-00
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
RES,CHIP
(KV-HF21M50)
120
5%
1/10W
R212
1-216-029-61
150
5%
1/10W
R213
R214
R215
R216
1-216-073-61
1-216-073-61
1-216-059-61
1-216-059-61
RES,CHIP
(KV-XF21M80)
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10G
10G
2.7K
2.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R217
R218
R219
1-216-067-00
1-216-067-00
1-216-025-61
METAL CHIP
METAL CHIP
RES,CHIP
5.6K
5.6K
100
5%
5%
5%
1/10W
1/10W
1/10W
<RESISTOR>
R001
R002
R003
R003
1-414-233-22
1-216-025-61
1-216-295-91
1-216-073-61
0UH
100
5%
0 (KV-HF21M50)
10G
5%
1/10W
1-216-025-61
INDUCTOR CHIP
RES,CHIP
SHORT
RES,CHIP
(KV-XF21M80)
RES,CHIP
R004
100
5%
1/10W
R005
R007
R008
R010
R011
1-216-025-61
1-216-295-61
1-216-065-61
1-216-065-61
1-216-065-61
RES,CHIP
SHORT CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
0
4.7K
4.7K
4.7K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R012
R013
R014
R015
R016
1-216-065-61
1-216-065-61
1-216-025-61
1-216-025-61
1-216-025-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
4.7K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R017
R018
R019
R021
R022
1-216-049-61
1-216-033-61
1-216-073-61
1-216-073-61
1-216-033-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
220
10G
10G
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R024
R025
R026
R027
R029
1-216-057-61
1-216-057-61
1-216-057-61
1-216-073-61
1-216-049-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
2.2K
2.2K
10G
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R031
R035
R036
R037
R040
1-216-049-61
1-216-025-61
1-216-025-61
1-216-025-61
1-216-025-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R041
R042
R043
R044
R045
1-216-025-61
1-216-295-61
1-216-049-61
1-216-025-61
1-414-233-22
RES,CHIP
SHORT CHIP
RES,CHIP
RES,CHIP
INDUCTOR CHIP
100
0
1K
100
0UH
5%
1/10W
5%
5%
1/10W
1/10W
1/10W
– 76 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
A
DESCRIPTION
REMARK
R220
R221
1-216-025-61
1-216-295-61
RES,CHIP
SHORT CHIP
100
0
R222
R225
R226
R227
R228
1-216-295-61
1-216-033-61
1-216-033-61
1-216-033-61
1-249-389-11
SHORT CHIP
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
R229
R230
1-216-073-61
1-216-061-00
R230
1-216-069-61
R231
R234
1-216-295-61
1-249-389-11
RES,CHIP
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
SHORT CHIP
CARBON
R235
R236
R237
R301
R302
1-216-069-61
1-216-069-61
1-216-308-61
1-216-073-61
1-216-295-61
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
SHORT CHIP
R303
R304
R305
R306
R307
1-216-049-61
1-216-073-61
1-216-051-61
1-216-073-61
1-216-025-61
R308
R309
R310
R311
R312
REF. NO. PART NO.
DESCRIPTION
REMARK
5%
1/10W
R357
R358
R359
1-216-079-00
1-216-049-61
1-216-033-61
METAL CHIP
RES,CHIP
RES,CHIP
18K
1K
220
5%
5%
5%
1/10W
1/10W
1/10W
0
220
220
220
4.7
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
R360
R361
R362
R363
R364
1-216-033-61
1-216-073-61
1-216-075-61
1-216-079-00
1-216-295-61
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
SHORT CHIP
220
10G
12K
18K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
10G
3.3K
5%
5%
1/10W
1/10W
6.8K
5%
1/10W
0
4.7
R365
R366
R367
R370
R376
1-216-033-61
1-216-073-61
1-216-073-61
1-216-033-61
1-216-081-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
220
10G
10G
220
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
1/4W
6.8K
6.8K
4.7
10G
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R377
R378
R401
R402
R403
1-216-121-61
1-216-031-61
1-216-049-61
1-216-073-61
1-216-073-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1M
180
1K
10G
10G
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
10G
1.2K
10G
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R404
R405
R406
R407
1-216-073-61
1-216-049-61
1-216-073-61
1-216-049-91
10G
1K
10G
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R407
1-216-049-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
(KV-HF21M50)
RES,CHIP
(KV-XF21M80)
1K
5%
1/10W
1-216-025-61
1-216-025-61
1-216-025-61
1-216-017-61
1-216-041-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100
100
100
47
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R408
R409
R410
R411
R412
1-216-049-61
1-216-041-61
1-216-113-61
1-216-113-61
1-216-041-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
1K
470
470K
470K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R313
R314
R316
R317
R318
1-216-053-61
1-216-045-00
1-216-053-61
1-216-077-61
1-216-051-61
RES,CHIP
METAL CHIP
RES,CHIP
REGISTER
RES,CHIP
1.5K
680
1.5K
0
1.2K
5%
5%
5%
1/10W
1/10W
1/10W
RES,CHIP
RES,CHIP
RES,CHIP
REGISTER
REGISTER
68
470K
470K
0
0
1/10W
1/10W
1/10W
1/10W
1-216-021-61
1-216-113-61
1-216-113-61
1-216-077-61
1-216-077-61
5%
5%
5%
5%
R413
R414
R415
R416
R417
R319
R320
R321
R322
R326
1-216-025-61
1-216-065-61
1-216-073-61
1-216-033-61
1-216-295-61
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
SHORT CHIP
100
4.7K
10G
220
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R418
R419
R426
R505
R506
1-216-113-61
1-216-022-00
1-216-033-61
1-216-101-61
1-216-085-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
470K
75
220
150K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R331
R332
R333
R334
R335
1-216-295-61
1-216-033-61
1-216-073-61
1-216-129-61
1-216-045-00
SHORT CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
0
220
10G
2.2M
680
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R507
R508
R509
R510
R511
1-249-389-11
1-215-910-00
1-215-911-11
1-215-885-00
1-215-911-11
CARBON
METAL OXIDE
METAL OXIDE
METAL OXIDE
METAL OXIDE
4.7
68
100
68
100
5%
5%
5%
5%
5%
1/4W
3W
3W
2W
3W
R338
R340
R345
R346
1-216-033-61
1-216-025-61
1-216-081-61
1-216-051-61
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R347
1-216-051-61
RES,CHIP
220
RES,CHIP
100
RES,CHIP
22K
RES,CHIP
1.2K
(KV-XF21M80 ONLY)
RES,CHIP
1.2K
(KV-XF21M80 ONLY)
5%
1/10W
R516
R518
R520
R522
R523
1-216-081-61
1-220-948-91
1-215-445-00
1-216-675-91
1-220-952-91
RES,CHIP
METAL
METAL
METAL CHIP
METAL MELF
22K
100
10K
10K
330
5%
5%
1%
0.50%
5%
1/10W
1/2W
1/4W
1/10W
1/2W
R348
R349
R350
R351
R354
1-216-675-91
1-216-073-61
1-216-061-61
1-216-053-61
1-216-057-61
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
10G
3.3G
1.5K
2.2K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R525
R526
R527
R528
R529
1-218-776-11
1-208-798-11
1-216-001-61
1-216-683-11
1-216-635-11
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
1M
4.7K
10
22K
220
0.50%
0.50%
5%
0.50%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
RES,CHIP
RES,CHIP
2.2K
2.2K
5%
5%
1/10W
1/10W
1-220-963-91
1-220-958-91
1-216-361-00
METAL MELF
REGISTER
METAL OXIDE
3.3K
0
0.22
1/2W
1-216-057-61
1-216-057-61
R531
R533
R534
5%
R355
R356
5%
2W
– 77 –
F
F
F
F
F
F
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
A
REF. NO. PART NO.
DESCRIPTION
REMARK
R535
R536
1-216-067-00
1-216-067-00
METAL CHIP
METAL CHIP
5.6K
5.6K
5%
5%
1/10W
1/10W
R537
R540
R541
R542
R543
1-216-683-11
1-216-065-61
1-216-065-61
1-216-295-61
1-249-426-11
METAL CHIP
RES,CHIP
RES,CHIP
SHORT CHIP
CARBON
22K
4.7K
4.7K
0
5.6K
0.50% 1/10W
5%
1/10W
5%
1/10W
5%
R544
R545
R546
R547
R549
1-215-918-00
1-216-077-61
1-216-077-61
1-216-085-00
1-215-451-00
METAL OXIDE
REGISTER
REGISTER
METAL CHIP
METAL
1.5K
0
0
33K
18K
R550
R551
R552
R553
R554
1-216-097-61
1-220-961-91
1-216-057-61
1-215-457-00
1-215-457-00
RES,CHIP
METAL CHIP
RES,CHIP
METAL
METAL
R556
R557
R558
R559
R560
1-215-437-00
1-216-345-11
1-220-961-91
1-220-969-91
1-216-073-61
R562
R565
R567
R568
R570
REF. NO. PART NO.
DESCRIPTION
REMARK
R616
R617
R619
R620
R622
1-260-302-51
1-247-791-91
1-260-128-11
1-215-915-11
1-215-908-00
CARBON
CARBON
CARBON
METAL OXIDE
METAL OXIDE
(KV-HF21M50)
6.8
22
270K
470
33
5%
5%
5%
5%
5%
1/2W F
1/4W
1/2W
3W
F
3W
F
1/4W F
R622
1-216-400-11
8.2
5%
3W
5%
3W
82K
0
1K
6.8
1/10W
1/10W
1/4W
1-216-095-61
1-216-089-61
1-216-049-61
1-240-251-11
5%
5%
1%
R623
R624
R626
R627
METAL OXIDE
(KV-XF21M80)
RES,CHIP
REGISTER
RES,CHIP
CMT,MELF
5%
5%
1/10W
10W
100K
2.2K
2.2K
33K
33K
5%
5%
5%
1%
1%
1/10W
1/2W
1/10W
1/4W
1/4W
R629
R630
R631
R632
R634 !
1-247-747-11
1-249-429-11
1-216-089-61
1-202-933-61
1-218-265-91
CARBON
CARBON
REGISTER
FUSIBLE
METAL
470
10K
0
0.1
8.2M
5%
5%
1/2W F
1/4W F
10%
5%
1/2W F
1W
METAL
METAL OXIDE
METAL CHIP
METAL CHIP
RES,CHIP
4.7K
0.47
2.2K
10K
10G
1%
5%
5%
5%
5%
1/4W
1W
F
1/2W
1/2W
1/10W
R635
R636
R637
R639
R640
1-216-492-11
1-215-924-00
1-216-492-11
1-216-363-00
1-220-956-91
METAL OXIDE
METAL OXIDE
METAL OXIDE
METAL OXIDE
METAL MELF
82K
15K
82K
0.33
680
5%
5%
5%
5%
5%
3W
3W
3W
2W
1/2W
1-249-401-11
1-216-073-61
1-216-105-61
1-249-383-11
1-216-069-61
CARBON
RES,CHIP
METAL CHIP
CARBON
RES,CHIP
47
10G
220K
1.5
6.8K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W F
1/10W
R641
R642
R643
R644
R646
1-216-362-11
1-220-959-91
1-220-963-91
1-220-959-91
1-215-924-00
METAL OXIDE
METAL MELF
METAL MELF
METAL MELF
METAL OXIDE
0.27
1.5K
3.3K
1.5K
15K
5%
5%
5%
5%
5%
2W
F
1/2W
1/2W
1/2W
3W
F
R571
R573
R577
R578
R579
1-215-437-00
1-216-089-61
1-215-913-11
1-216-369-00
1-216-097-61
METAL
REGISTER
METAL OXIDE
METAL OXIDE
RES,CHIP
4.7K
0
220
1
100K
1%
1/4W
CARBON
RES,CHIP
REGISTER
METAL OXIDE
METAL OXIDE
47
2.2K
0
22
22K
1/4W
1/10W
3W
F
2W
F
1/10W
1-249-401-11
1-216-057-61
1-220-958-91
1-215-882-00
1-215-900-11
5%
5%
5%
5%
5%
R647
R648
R649
R650
R652
5%
5%
2W
2W
R580
R581
R585
R588
R589
1-216-699-91
1-208-798-11
1-249-391-11
1-215-888-00
1-215-888-00
METAL CHIP
RES,CHIP
CARBON
METAL OXIDE
METAL OXIDE
100K
4.7K
6.8
220
220
0.50%
0.50%
5%
5%
5%
1/10W
1/10W
1/4W F
2W
F
2W
F
R653
R657
R659
R660
R661
1-215-873-00
1-260-127-11
1-216-049-61
1-216-073-61
1-215-873-00
METAL OXIDE
CARBON
RES,CHIP
RES,CHIP
METAL OXIDE
4.7K
220K
1K
10G
4.7K
5%
5%
5%
5%
5%
1W
F
1/2W
1/10W
1/10W
1W
F
R590
R591
R593
R594
R596
1-215-465-00
1-260-288-11
1-260-288-11
1-260-288-11
1-215-920-11
METAL
CARBON
CARBON
CARBON
METAL OXIDE
68K
0.47
0.47
0.47
3.3K
1%
5%
5%
5%
5%
1/4W
1/2W
1/2W
1/2W
3W
R680
R901
R902
1-216-308-61
1-220-952-91
1-249-411-11
4.7
330
330
5%
5%
5%
1/10W
1/2W
1/4W
R902
1-220-952-91
330
5%
1/2W
R903
1-216-022-00
METAL CHIP
METAL MELF
CARBON
(KV-HF21M50)
METAL MELF
(KV-XF21M80)
METAL CHIP
75
5%
1/10W
R597
R599
R600
R601
R602
1-247-750-11
1-249-389-11
1-220-976-91
1-249-418-11
1-249-389-11
CARBON
CARBON
METAL MELF
CARBON
CARBON
680
4.7
56K
1.2K
4.7
5%
5%
5%
5%
5%
1/2W F
1/4W
1/2W
1/4W F
1/4W F
R904
R905
R906
R907
R908
1-216-033-61
1-216-113-61
1-216-077-61
1-216-113-61
1-216-077-61
RES,CHIP
RES,CHIP
REGISTER
RES,CHIP
REGISTER
220
470K
0
470K
0
5%
5%
1/10W
1/10W
5%
1/10W
R603
R604
R607
R608
R609
1-215-485-00
1-216-097-61
1-220-965-91
1-240-205-91
1-216-057-61
METAL
RES,CHIP
METAL CHIP
CARBON
RES,CHIP
470K
100K
4.7K
22M
2.2K
1%
5%
5%
5%
5%
1/4W
1/10W
1/2W
1/2W
1/10W
R909
R910
R911
R912
R913
1-216-065-61
1-216-065-61
1-216-067-00
1-216-041-61
1-216-049-61
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
4.7K
4.7K
5.6K
470
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R610
R611
R612
R614
R615
1-216-073-61
1-216-089-61
1-216-045-00
1-216-041-61
1-216-350-11
RES,CHIP
REGISTER
METAL CHIP
RES,CHIP
METAL OXIDE
10G
0
680
470
1.2
5%
1/10W
5%
5%
5%
1/10W
1/10W
1W
F
R914
R915
R916
1-216-055-61
1-216-061-61
1-216-017-61
RES,CHIP
RES,CHIP
RES,CHIP
1.8K
3.3G
47
5%
5%
5%
1/10W
1/10W
1/10W
F
F
F
F
F
– 78 –
F
F
F
F
F
F
F
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
R917
R918
1-216-041-61
1-216-041-61
A C3 (KV-HF21M50)
DESCRIPTION
RES,CHIP
RES,CHIP
REMARK
470
470
5%
5%
1/10W
1/10W
<RELAY>
RY601 ! 1-755-266-11
RELAY, AC POWER
<SWITCH>
S502
1-572-707-11
S600 ! 1-571-433-31
S901
1-692-431-21
S902
1-692-431-21
S903
1-692-431-21
SWITCH, LEVER
SWITCH, PUSH (AC POWER)
SWITCH, TACTILE
SWITCH, TACTILE
SWITCH, TACTILE
S904
S905
S906
S907
SWITCH, TACTILE
SWITCH, TACTILE
SWITCH, TACTILE
SWITCH, TACTILE
1-692-431-21
1-692-431-21
1-692-431-21
1-692-431-21
REF. NO. PART NO.
T601
1-424-682-11
T603 ! 1-433-513-31
T604 ! 1-431-852-11
1-102-114-00
1-102-114-00
1-102-114-00
1-102-116-00
1-102-116-00
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
470PF
470PF
470PF
680PF
680PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C714
C716
C717
C736
C737
1-102-116-00
1-126-933-11
1-101-880-00
1-102-114-00
1-102-114-00
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
680PF
100MF
47PF
470PF
470PF
10%
20%
5%
10%
10%
50V
16V
50V
50V
50V
C746
1-102-114-00
CERAMIC
470PF
10%
50V
<CONNECTOR>
CN701 1-508-765-00
CN702 1-695-915-11
CN703 * 1-564-509-11
CN704 1-695-915-11
TRANSFORMER, HORIZONTAL DRIVE
TRANSFORMER ASSY, FLYBACK (NX-1748//
M3A4)
TRANSFORMER, LINE FILTER
TRANSFORMER, CONVERTER (SRT)
TRANSFORMER, CONVERTER (SRT)
THERMISTOR, POSITIVE
<TUNER>
TU101
8-598-449-10
TUNER, FSS BTF-LG433
D701
D702
D703
D707
D708
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
D709
D710
D711
D712
D713
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
D714
D715
D716
D717
8-719-911-19
8-719-911-19
8-719-911-19
8-719-121-26
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE RD9.1ESL2
<CRYSTAL>
X001
X301
X302
1-579-125-11
1-781-134-21
1-781-132-21
PIN, CONNECTOR (5MM PITCH) 3P
TAB (CONTACT)
PLUG, CONNECTOR 6P
TAB (CONTACT)
<DIODE>
<THERMISTOR>
THP600 1-810-961-11
REMARK
C708
C709
C710
C712
C713
<TRANSFORMER>
T501
1-437-195-11
T503 ! 1-453-293-11
DESCRIPTION
<JACK>
J701 ! 1-540-071-22
VIBRATOR, CERAMIC
VIBRATOR, CRYSTAL
VIBRATOR, CRYSTAL
SOCKET, CRT
<COIL>
****************************************************************************
L701
L710
L711
L712
1-410-667-31
1-408-613-31
1-408-613-31
1-408-613-31
* A-1331-884-A C3 BOARD, MOUNTED (KV-HF21M50 ONLY)
*********************
7-682-948-01
SCREW +PSW 3X8
<CAPACITOR>
C701
C702
C703
C704
C706
1-162-114-00
1-102-074-00
1-107-651-11
1-130-202-00
1-104-664-11
CERAMIC
CERAMIC
ELECT
FILM
ELECT
0.0047MF
0.001MF
4.7MF
0.022MF
47MF
10%
20%
5%
20%
2KV
50V
250V
400V
16V
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
22UH
68UH
68UH
68UH
<TRANSISTOR>
Q704
Q705
Q706
Q707
Q708
8-729-326-11
8-729-326-11
8-729-326-11
8-729-200-17
8-729-200-17
TRANSISTOR 2SC2611
TRANSISTOR 2SC2611
TRANSISTOR 2SC2611
TRANSISTOR 2SA1091-O
TRANSISTOR 2SA1091-O
Q709
Q710
Q711
Q712
8-729-200-17
8-729-119-78
8-729-119-78
8-729-119-78
TRANSISTOR 2SA1091-O
TRANSISTOR 2SC2785-HFE
TRANSISTOR 2SC2785-HFE
TRANSISTOR 2SC2785-HFE
– 79 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
C3 (KV-HF21M50) C5 (KV-XF21M80)
REF. NO. PART NO.
DESCRIPTION
REMARK
<RESISTOR>
REF. NO. PART NO.
1-102-114-00
1-102-114-00
1-102-114-00
1-102-116-00
1-102-116-00
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
470PF
470PF
470PF
680PF
680PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C714
C716
C717
C736
C737
1-102-116-00
1-126-933-11
1-101-880-00
1-102-114-00
1-102-114-00
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
680PF
100MF
47PF
470PF
470PF
10%
20%
5%
10%
10%
50V
16V
50V
50V
50V
C746
C1803
C1804
C1809
1-102-114-00
1-125-797-91
1-125-797-91
1-126-942-61
CERAMIC
ELECT
ELECT
ELECT
470PF
10MF
10MF
1000MF
10%
20%
20%
20%
50V
50V
50V
25V
1-249-496-11
1-216-380-11
1-215-417-00
1-215-413-00
1-216-379-11
CARBON
METAL OXIDE
METAL
METAL
METAL OXIDE
100K
8.2
680
470
6.8
5%
5%
1%
1%
5%
1/2W
2W
F
1/4W
1/4W
2W
F
R710
R711
R712
R713
R714
1-215-922-11
1-247-752-11
1-215-922-11
1-247-752-11
1-215-922-11
METAL OXIDE
CARBON
METAL OXIDE
CARBON
METAL OXIDE
6.8K
1K
6.8K
1K
6.8K
5%
5%
5%
5%
5%
3W
F
1/2W
3W
F
1/2W
3W
F
R715
R719
R720
R721
R722
1-247-752-11
1-215-480-00
1-249-923-11
1-215-489-00
1-249-923-11
CARBON
METAL
CARBON
METAL
CARBON
1K
300K
1K
680K
1K
5%
1%
5%
1%
5%
1/2W
1/4W
1/4W F
1/4W
1/4W F
R723
R724
R725
R726
R727
1-215-479-00
1-249-923-11
1-249-421-11
1-249-421-11
1-249-421-11
METAL
CARBON
CARBON
CARBON
CARBON
270K
1K
2.2K
2.2K
2.2K
1%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W
1/4W
CN701
CN702
CN703 *
CN704
CN1801*
R728
R729
R730
R731
R732
1-249-407-11
1-249-407-11
1-249-407-11
1-249-407-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
150
150
150
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
CN1802* 1-564-506-11
R733
R734
R738
R739
R740
1-249-406-11
1-247-739-11
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
120
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/2W
1/4W
1/4W
1/4W
R755
R756
R757
1-249-418-11
1-249-418-11
1-249-418-11
CARBON
CARBON
CARBON
1.2K
1.2K
1.2K
5%
5%
5%
1/4W
1/4W
1/4W
<CONNECTOR>
1-508-765-00
1-695-915-11
1-564-509-11
1-695-915-11
1-564-507-11
RES, ADJ, METAL FILM 110M
****************************************************************************
PLUG, CONNECTOR 3P
D701
D702
D703
D707
D708
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
D709
D710
D711
D712
D713
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
D714
D715
D716
D717
D1803
8-719-911-19
8-719-911-19
8-719-911-19
8-719-121-26
8-719-911-19
DIODE 1SS119-25
DIODE 1SS119-25
DIODE 1SS119-25
DIODE RD9.1ESL2
DIODE 1SS119-25
D1804
D1808
8-719-911-19
8-719-908-03
DIODE 1SS119-25
DIODE GP08D
* A-1331-948-A C5 BOARD, MOUNTED (KV-XF21M80 ONLY)
*********************
<IC>
IC1800
7-682-948-01
PIN, CONNECTOR (5MM PITCH) 3P
TAB (CONTACT)
PLUG, CONNECTOR 6P
TAB (CONTACT)
PLUG, CONNECTOR 4P
<DIODE>
<VARIABLE RESISTOR>
1-241-656-21
REMARK
C708
C709
C710
C712
C713
R703
R705
R706
R707
R708
RV702
DESCRIPTION
8-759-822-38
IC LA6510
SCREW +PSW 3X8
<JACK>
<CAPACITOR>
J701 ! 1-540-071-22
C701
C702
C703
C704
C706
1-162-114-00
1-102-074-00
1-107-651-11
1-130-202-00
1-104-664-11
CERAMIC
CERAMIC
ELECT
FILM
ELECT
0.0047MF
0.001MF
4.7MF
0.022MF
47MF
10%
20%
5%
20%
2KV
50V
250V
400V
16V
SOCKET, CRT
<COIL>
L701
L710
L711
– 80 –
1-410-667-31
1-408-609-41
1-408-609-41
INDUCTOR
INDUCTOR
INDUCTOR
22UH
33UH
33UH
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
L712
1-408-609-41
C5 (KV-XF21M80) F
DESCRIPTION
INDUCTOR
REMARK
33UH
<TRANSISTOR>
Q704
Q705
Q706
Q707
Q708
8-729-326-11
8-729-326-11
8-729-326-11
8-729-200-17
8-729-200-17
TRANSISTOR 2SC2611
TRANSISTOR 2SC2611
TRANSISTOR 2SC2611
TRANSISTOR 2SA1091-O
TRANSISTOR 2SA1091-O
Q709
Q710
Q711
Q712
Q1802
8-729-200-17
8-729-119-78
8-729-119-78
8-729-119-78
8-729-119-78
TRANSISTOR 2SA1091-O
TRANSISTOR 2SC2785-HFE
TRANSISTOR 2SC2785-HFE
TRANSISTOR 2SC2785-HFE
TRANSISTOR 2SC2785-HFE
REF. NO. PART NO.
DESCRIPTION
REMARK
R1811
R1812
R1821
R1822
R1823
1-220-974-91
1-220-974-91
1-220-974-91
1-220-974-91
1-220-966-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
33K
33K
33K
5.6K
5%
5%
5%
5%
5%
1/2W
1/2W
1/2W
1/2W
1/2W
R1824
1-220-974-91
METAL CHIP
33K
5%
1/2W
<VARIABLE RESISTOR>
RV702
1-241-656-21
RES, ADJ, METAL FILM 110M
****************************************************************************
<RESISTOR>
R703
R705
R706
R707
R708
1-249-496-11
1-216-380-11
1-215-417-00
1-215-413-00
1-216-379-11
CARBON
METAL OXIDE
METAL
METAL
METAL OXIDE
100K
8.2
680
470
6.8
5%
5%
1%
1%
5%
1/2W
2W
F
1/4W
1/4W
2W
F
R710
R711
R712
R713
R714
1-215-922-11
1-247-752-11
1-215-922-11
1-247-752-11
1-215-922-11
METAL OXIDE
CARBON
METAL OXIDE
CARBON
METAL OXIDE
6.8K
1K
6.8K
1K
6.8K
5%
5%
5%
5%
5%
3W
F
1/2W
3W
F
1/2W
3W
F
R715
R719
R720
R721
R722
1-247-752-11
1-215-480-00
1-249-923-11
1-215-489-00
1-249-923-11
CARBON
METAL
CARBON
METAL
CARBON
1K
300K
1K
680K
1K
5%
1%
5%
1%
5%
1/2W
1/4W
1/4W F
1/4W
1/4W F
R723
R724
R725
R726
R727
1-215-479-00
1-249-923-11
1-220-961-91
1-220-961-91
1-220-961-91
METAL
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
270K
1K
2.2K
2.2K
2.2K
1%
5%
5%
5%
5%
1/4W
1/4W F
1/2W
1/2W
1/2W
R728
R729
R730
R731
R732
1-220-949-91
1-220-949-91
1-220-949-91
1-249-399-11
1-249-399-11
METAL MELF
METAL MELF
METAL MELF
CARBON
CARBON
150
150
150
33
33
5%
5%
5%
5%
5%
1/2W
1/2W
1/2W
1/4W
1/4W
R733
R734
R738
R739
R740
1-249-399-11
1-247-739-11
1-220-948-91
1-220-948-91
1-220-948-91
CARBON
CARBON
METAL
METAL
METAL
33
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/2W
1/2W
1/2W
1/2W
R755
R756
R757
R1802
R1803
1-249-418-11
1-249-418-11
1-249-418-11
1-249-387-11
1-249-387-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.2K
1.2K
1.2K
3.3
3.3
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W F
1/4W F
R1805
R1806
R1808
R1809
R1810
1-220-969-91
1-220-965-91
1-220-965-91
1-220-974-91
1-220-974-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
4.7K
4.7K
33K
33K
5%
5%
5%
5%
5%
1/2W
1/2W
1/2W
1/2W
1/2W
* A-1241-355-A F BOARD, MOUNTED (KV-HF21M50)
*******************
* A-1241-372-A F BOARD, MOUNTED (KV-XF21M80)
*******************
1-533-223-11
* 4-374-846-01
HOLDER, FUSE
COVER, CAPACITOR, CAP TYPE
<CAPACITOR>
C654 ! 1-117-703-11
C4602 ! 1-104-708-51
CERAMIC
FILM
0.0047MF
0.47MF
99%
20%
250V
250V
<CONNECTOR>
CN4601* 1-580-843-11
CN4602* 1-580-843-11
CN4603 1-695-915-11
PIN, CONNECTOR (POWER)
PIN, CONNECTOR (POWER)
TAB (CONTACT)
<FUSE>
F4601 ! 1-532-237-11
FUSE, TIME-LAG (BET) 3.15A/250V
<RESISTOR>
R4601 ! 1-202-719-91
SOLID
1M
10%
1/2W
<TRANSFORMER>
T4601
T4602
T4601
T4602
1-424-682-11
1-424-682-11
1-431-747-11
1-431-747-11
TRANSFORMER, LINE FILTER (KV-HF21M50)
TRANSFORMER, LINE FILTER (KV-HF21M50)
TRANSFORMER, LINE FILTER (KV-XF21M80)
TRANSFORMER, LINE FILTER (KV-XF21M80)
<VARISTOR>
VDR461 1-801-073-31
VARISTOR TNR14V471K660
****************************************************************************
– 81 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
VM1
REF. NO. PART NO.
DESCRIPTION
REMARK
* A-1342-453-A VM1 BOARD, MOUNTED (KV-HF21M50)
***********************
* A-1342-488-A VM1 BOARD, MOUNTED (KV-XF21M80)
***********************
4-382-854-11
SCREW (M3X10), P, SW (+)
<CAPACITOR>
C5902
C5903
C5905
C5906
C5907
1-107-883-11
1-161-830-00
1-126-925-11
1-130-491-00
1-107-638-11
ELECT
CERAMIC
ELECT
MYLAR
ELECT
330MF
0.0047MF
470MF
0.047MF
33MF
20%
20%
5%
20%
16V
500V
10V
50V
160V
C5908
C5909
C5910
C5911
C5912
1-106-383-00
1-126-968-11
1-130-471-00
1-107-949-11
1-104-999-11
MYLAR
ELECT
MYLAR
ELECT
MYLAR
0.047MF
100MF
0.001MF
2.2MF
0.1MF
10%
20%
5%
20%
10%
200V
50V
50V
160V
200V
C5913
C5914
C5916
C5917
C5918
1-130-471-00
1-126-933-11
1-130-491-00
1-126-925-11
1-115-341-51
MYLAR
ELECT
MYLAR
ELECT
CERAMIC
0.001MF
100MF
0.047MF
470MF
120PF
5%
20%
5%
20%
10%
50V
16V
50V
10V
500V
C5920
C5921
1-125-797-91
1-101-888-00
ELECT
CERAMIC
10MF
68PF
20%
5%
50V
50V
<CONNECTOR>
CN5901* 1-564-510-11
CN5904* 1-770-723-11
PLUG, CONNECTOR 7P
CONNECTOR, BOARD TO BOARD 8P
REF. NO. PART NO.
DESCRIPTION
REMARK
<RESISTOR>
R5901
R5902
R5903
R5904
R5905
1-220-951-91
1-249-414-11
1-247-735-11
1-220-952-91
1-220-958-91
METAL
CARBON
CARBON
METAL MELF
REGISTER
220
560
47
330
0
5%
5%
5%
5%
1/2W
1/4W F
1/2W F
1/2W
R5906
R5907
R5908
R5909
R5910
1-220-958-91
1-220-958-91
1-249-383-11
1-220-951-91
1-220-946-81
REGISTER
REGISTER
CARBON
METAL
METAL MELF
0
0
1.5
220
68
5%
5%
5%
1/4W F
1/2W
1/2W
R5911
R5912
R5914
R5915
R5916
1-249-439-11
1-220-975-91
1-220-946-81
1-220-969-91
1-220-959-91
CARBON
METAL MELF
METAL MELF
METAL CHIP
METAL MELF
68K
47K
68
10K
1.5K
5%
5%
5%
5%
5%
1/4W
1/2W
1/2W
1/2W
1/2W
R5917
R5918
R5919
R5920
R5921
1-220-957-91
1-220-969-91
1-249-417-11
1-249-439-11
1-215-912-11
METAL MELF
METAL CHIP
CARBON
CARBON
METAL OXIDE
820
10K
1K
68K
150
5%
5%
5%
5%
5%
1/2W
1/2W
1/4W F
1/4W
3W
F
R5922
R5923
R5925
R5929
R5930
1-220-955-91
1-249-383-11
1-249-401-11
1-215-880-00
1-220-954-91
METAL MELF
CARBON
CARBON
METAL OXIDE
METAL MELF
560
1.5
47
10
470
5%
5%
5%
5%
5%
1/2W
1/4W F
1/4W F
2W
F
1/2W
R5931
R5932
R5933
R5934
R5935
1-220-954-91
1-220-954-91
1-220-954-91
1-220-970-91
1-220-969-91
METAL MELF
METAL MELF
METAL MELF
METAL MELF
METAL CHIP
470
470
470
12K
10K
5%
5%
5%
5%
5%
1/2W
1/2W
1/2W
1/2W
1/2W
<DIODE>
D5901
D5902
D5903
D5904
D5905
8-719-911-19
8-719-110-88
8-719-911-19
8-719-110-88
8-719-911-19
DIODE 1SS119-25
DIODE RD39ESB2
DIODE 1SS119-25
DIODE RD39ESB2
DIODE 1SS119-25
D5906
D5907
1-249-406-11
1-249-406-11
CARBON
CARBON
****************************************************************************
MISCELLANEOUS
*************
120
120
5%
5%
1/4W
1/4W
! 1-416-946-11
1-417-151-21
<COIL>
L5901
L5902
1-414-187-11
1-414-856-11
INDUCTOR
INDUCTOR
1-452-032-00
1-452-094-00
1-452-728-41
47UH
10UH
<TRANSISTOR>
Q5901
Q5902
Q5903
Q5904
Q5905
8-729-230-45
8-729-017-05
8-729-230-45
8-729-119-76
8-729-230-45
TRANSISTOR 2SC2458-YGR
TRANSISTOR 2SA1837
TRANSISTOR 2SC2458-YGR
TRANSISTOR 2SA1175-HFE
TRANSISTOR 2SC2458-YGR
Q5906
Q5908
Q5909
8-729-017-06
8-729-119-78
8-729-119-78
TRANSISTOR 2SC4793
TRANSISTOR 2SC2785-HFE
TRANSISTOR 2SC2785-HFE
COIL, DEMAGNETIC
MATCHING TRANSFORMER, ANTENNA
(KV-HF21M50 ONLY)
MAGNET,DISC
CIRCULAR DISC MAGNET B
COIL, NA ROTATION (RT-154)
(KV-HF21M50 ONLY)
1-501-372-81
1-503-902-11
1-529-125-11
! 1-574-062-52
8-451-505-11
ANTENNA, TELESCOPIC (KV-HF21M50 ONLY)
SPEAKER (15X6.5CM) (KV-HF21M50)
SPEAKER (13X7CM) (KV-XF21M80)
CORD, POWER (WITH CONNECTOR) 2.5A/250V
DEFLECTION YOKE (Y21RSA-S)
8-453-011-31
! 8-738-812-05
! 8-738-809-05
NA299-S2
PICTURE TUBE (A51LPT70X) (KV-HF21M50)
PICTURE TUBE (A51LPT70X) (KV-XF21M80)
****************************************************************************
– 82 –
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
DESCRIPTION
REMARK
REF. NO. PART NO.
ACCESSORIES AND PACKING MATERIALS (KV-HF21M50)
***************************************
1-417-151-21
1-501-372-81
3-701-910-00
3-867-625-12
* 4-039-372-01
MATCHING TRANSFORMER, ANTENNA
ANTENNA, TELESCOPIC
SCREW, SPECIAL (DIA. 3.8X20)
MANUAL, INSTRUCTION
BAG, PROTECTION
* 4-067-165-01
* 4-067-166-01
* 4-067-175-01
4-392-003-11
4-392-004-11
CUSHION,(LOWER)(ASS’Y)
CUSHION (UPPER)(ASS’Y)
INDIVIDUAL CARTON
BAND, HOLD
CLIP
****************************************************************************
ACCESSORIES AND PACKING MATERIALS (KV-XF21M80)
***************************************
3-701-910-00
3-866-882-11
* 4-053-003-01
* 4-070-796-01
* 4-070-797-01
SCREW, SPECIAL (DIA. 3.8X20)
MANUAL, INSTRUCTION
BAG, PROTECTION
CUSHION (UPPER)(ASSY)
CUSHION (LOWER)(ASSY)
* 4-071-142-01
4-392-003-31
4-392-004-21
INDIVIDUAL CARTON
BAND, HOLD
CLIP
****************************************************************************
REMOTE COMMANDER
**********************
1-418-163-11
9-939-697-01
REMOTE COMMANDER (RM-952)
BATTERY COVER, REMOTE COMMANDER
– 83 –
DESCRIPTION
REMARK
KV-HF21M50/XF21M80
RM-952
The components identified by shading
and mark ! are critical for safety.
Replace only with part number specified.
REF. NO. PART NO.
DESCRIPTION
REMARK
REF. NO. PART NO.
Sony Corporation
9-965-751-01
Sony TV Industries (M) Sdn. Bhd.
TV Business of General Area
– 84 –
DESCRIPTION
REMARK
English
99GM70040-1
Printed in Malaysia
 1999.7