Download CPD-E500/E500E
Transcript
CPD-E500/E500E SERVICE MANUAL CPD-E500 US Model Canadian Model Chassis No. SCC-L22P-A CPD-E500E AEP Model Chassis No. SCC-L22N-A G1 CHASSIS SPECIFICATIONS CRT Viewable image size Resolution Maximum Recommended Standard image area Deflection frequency* 0.24 mm aperture grille pitch 21 inches measured diagonally 90-degree deflection FD Trinitron Approx. 403.8 × 302.2 mm (w/h) (16 × 12 inches) 19.8" viewing image AC input voltage/current Power consumption Dimensions Horizontal: 2048 dots Vertical: 1536 lines Horizontal: 1600 dots Vertical: 1200 lines Approx. 388 × 291 mm (w/h) (15 3/8 × 11 1/2 inches) or Approx. 364 × 291 mm (w/h) (14 3/8 × 11 1/2 inches) Horizontal: 30 to 109 kHz Vertical: 48 to 160 Hz * Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.3 µsec. • Vertical blanking width should be more than 450 µsec. ** If the input signal is Generalized Timing Formula (GTF) compliant, the GTF feature of the monitor will automatically provide an optimal image for the screen. Mass Plug and Play Supplied accessories 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A Approx. 145 W Approx. 497 × 480 × 478 mm (w/h/d) (19 5/8 × 19 × 18 7/8 inches) Approx. 32 kg (70 lb 9 oz) DDC1/2B/2Bi, GTF** See page 6 Design and specifications are subject to change without notice. TRINITRON COLOR COMPUTER DISPLAY ® CPD-E500/E500E SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below. To Exposed Metal Parts on Set 0.15 µF 1.5 kΩ AC Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) WARNING!! NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE DEGAUSS COIL HAS BEEN REMOVED. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ¡ ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. AVERTISSEMENT!! NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE DEMAGNETISATION EST ENLEVÉE. ATTENTION AUX COMPOSANTS RELATIFS À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE MARQUE ¡ SONT CRITIQUES POUR LA SÉCURITÉ. NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT IDENTIFIÉS DANS LE PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENT EST SUSPECTÉ. –2– CPD-E500/E500E Power saving function This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below. Power mode Power consumption 1 (power) indicator normal operation ≤ 145 W green 1 standby ≤ 15 W green and orange alternate 2 suspend (sleep)* ≤ 15 W green and orange alternate 3 active off** (deep sleep)* Approx. 1 W orange power off 0W off * “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency. ** When your computer enters a power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters a power saving mode. DIAGNOSIS If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cable and check the condition of your computer. This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer, the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard. If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition. If the 1 (power) indicator is flashing orange MENU RESET Press the 1 (power) button twice to turn the monitor off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. 1 (power) indicator If the 1 (power) indicator is green If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board. 1 Disconnect the video input cable or turn off the connected computer. 2 Press the 1 (power) button twice to turn the monitor off and then on. 3 Move the control button , for 2 seconds before the monitor enters power saving mode. MENU –3– CPD-E500/E500E TIMING SPECIFICATION MODE AT PRODUCTION MODE 1 RESOLUTION 1600 X 1200 CLOCK 229.500 MHz — HORIZONTAL — H-FREQ 106.250 kHz usec H. TOTAL 9.412 H. BLK 2.440 H. FP 0.279 H. SYNC 0.837 H. BP 1.325 H. ACTIV 6.972 — VERTICAL — V. FREQ(HZ) 85.000 Hz lines V. TOTAL V. BLK 1250 50 V. FP 1 V. SYNC 3 V. BP V. ACTIV 46 1200 — SYNC — INT(G) EXT(H/V)/POLARITY EXT(CS) /POLARITY INT/NON INT NO YES P/P NO NON INT 99.11.18 VER. –4– CPD-E500/E500E TABLE OF CONTENTS Section Title Page 1. GENERAL ................................................................. 1-1 2. DISASSEMBLY 2-1. Cabinet Removal ............................................... 2-2. D Board Removal .............................................. 2-3. G Board Removal .............................................. 2-4-1. A Board, I/O Terminal Board Assembly Removal (CPD-E500E) ...................................... 2-4-2. A Board, Terminal Bracket Removal (CPD-E500) ........................................ 2-5. N Board Removal .............................................. 2-6. Service Position .................................................. 2-7. Bezel Assembly, H1 Board Removal ................ 2-8. Picture Tube Removal ....................................... 2-9. J Board Removal ............................................... 2-10-1. Harness Location (CPD-E500E) ....................... 2-10-2.Harness Location (CPD-E500) ......................... 2-1 2-1 2-2 2-3 2-3 2-4 2-4 2-5 2-5 2-6 2-7 2-8 3. SAFETY RELATED ADJUSTMENT ............. 3-1 4. ADJUSTMENTS ..................................................... 4-1 5. DIAGRAMS 5-1. 5-2. 5-3. 5-4. (1) (2) (3) (4) (5) 5-5. Block Diagrams .................................................. Frame Schematic Diagram ................................. Circuit Boards Location ..................................... Schematic Diagrams and Printed Wiring Boards ................................................................. Schematic Diagram of A Board ........................ Schematic Diagrams of H1, J Boards ............... Schematic Diagram of D Board ........................ Schematic Diagrams of N (a, b, c) Board Schematic Diagram of G Board ........................ Semiconductors ................................................. 5-1 5-7 5-9 5-9 5-11 5-17 5-19 5-23 5-31 5-35 6. EXPLODED VIEWS 6-1. 6-2. 6-3. Chassis ............................................................... 6-1 Picture Tube ...................................................... 6-2 Packing Materials ............................................... 6-3 7. ELECTRICAL PARTS LIST ............................ 7-1 Note: Hand degauss must be used on stand-by or power-off condition. This model has an automatic earth magnetism correction function by using an earth magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimes gets magnetized, and the system may not work properly as a result. –5– SECTION 1 The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. GENERAL Use of the tilt-swivel Precautions Warning on power connections • Use the supplied power cord. If you use a different power cord, be sure that it is compatible with your local power supply. For the customers in the U.S.A. If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards. Example of plug types This monitor can be adjusted within the angles shown below. To find the center of the monitor’s turning radius, align the center of the monitor’s screen with the centering dots on the stand. Hold the monitor at the bottom with both hands when you turn it horizontally or vertically. Be careful not to pinch your fingers at the back of the monitor when you tilt the monitor up vertically. Identifying parts and controls See the pages in parentheses for further details. Front Rear MENU AC IN RESET 90˚ 15˚ MENU RESET 90˚ 5˚ for 100 to 120 V AC for 200 to 240 V AC • Before disconnecting the power cord, wait at least 30 seconds after turning off the power to allow the static electricity on the screen’s surface to discharge. • After the power is turned on, the screen is demagnetized (degaussed) for about 2 seconds. This generates a strong magnetic field around the screen which may affect data stored on magnetic tapes and disks placed near the monitor. Be sure to keep magnetic recording equipment, tapes, and disks away from the monitor. 1-1 The equipment should be installed near an easily accessible outlet. Installation Do not install the monitor in the following places: • on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies, etc.) that may block the ventilation holes • near heat sources such as radiators or air ducts, or in a place subject to direct sunlight • in a place subject to severe temperature changes • in a place subject to mechanical vibration or shock • on an unstable surface • near equipment which generates magnetism, such as a transformer or high voltage power lines • near or on an electrically charged metal surface Maintenance • Clean the screen with a soft cloth. If you use a glass cleaning liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the screen’s coating. • Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube. • Clean the cabinet, panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzene. Transportation Centering dots 1 RESET (reset) button (page 14) This button resets the adjustments to the factory settings. 4 AC IN connector (page 6) This connector provides AC power to the monitor. 2 Control button (page 9) The control button is used to display the menu and make adjustments to the monitor, including brightness and contrast adjustments. 5 Video input connector (HD15) (page 6) This connector inputs RGB video signals (0.700 Vp-p, positive) and sync signals. 3 1 (power) switch and indicator (pages 7, 14, 18) This button turns the monitor on and off. The power indicator lights up in green when the monitor is turned on, and either flashes in green and orange, or lights up in orange when the monitor is in power saving mode. US 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin No. Signal 1 Red 2 Green (Sync on Green) 3 Blue 4 ID (Ground) 5 DDC Ground* 6 Red Ground 7 Green Ground 8 Blue Ground 9 DDC + 5V* 10 Ground 11 ID (Ground) 12 Bi-Directional Data (SDA)* 13 H. Sync 14 V. Sync 15 Data Clock (SCL)* * DDC (Display Data Channel) is a standard of VESA. When you transport this monitor for repair or shipment, use the original carton and packing materials. 4 5 x Connecting to a Macintosh or compatible computer Setup Before using your monitor, check that the following accessories are included in your carton: • Power cord (1) • Macintosh adapter (for beige system) (1) • Setup Disk (1) • Warranty card (1) • Notes on cleaning the screen’s surface (1) • This instruction manual (1) AC IN Note Do not touch the pins of the video signal cable connector as this might bend the pins. x Connecting to an IBM PC/AT or compatible computer AC IN Selecting the on-screen menu language (LANG) First turn on the monitor, then turn on the computer. English, French, German, Spanish, Italian, Dutch, Swedish, Russian and Japanese versions of the on-screen menus are available. The default setting is English. 1 Press the center of the control button. See page 9 for more information on using the control button. The installation of your monitor is complete. If necessary, use the monitor’s controls to adjust the picture. Step 1: Connect your monitor to your computer Turn off the monitor and computer before connecting. Step 3: Turn on the monitor and computer MENU Macintosh adapter (for beige system) (supplied)* to video Macintosh or compatible computer output 1-2 * Connect the supplied Macintosh adapter to the computer before connecting the cable. This adapter is compatible with Macintosh LC, Performa, Quadra, Power Macintosh, and Power Macintosh G3 series computers that have two rows of pins. If you are connecting to the other version of Power Macintosh G3 series with three rows of pins or models other than those stated above, you will need a different adapter (not supplied). Step 2: Connect the power cord With the monitor and computer switched off, first connect the power cord to the monitor, then connect it to a power outlet. For customers using Windows NT4.0 Monitor setup in Windows NT4.0 is different from Windows 95/98 and does not involve the selection of monitor type. Refer to the Windows NT4.0 instruction manual for further details on adjusting the resolution, refresh rate, and number of colors. to video output GEOM EXIT COLOR LANG SIZE OPTION LANG and press the center of the control button again. MENU AC IN MENU CONV 2 Move the control button to highlight For more information about the on-screen messages, see “Trouble symptoms and remedies” on page 16. For customers using Windows 95/98 To maximize the potential of your monitor, install the new model information file from the supplied Setup Disk onto your PC. This monitor complies with the “VESA DDC” Plug & Play standard. If your PC/graphics board complies with DDC, select “Plug & Play Monitor (VESA DDC)” or this monitor’s model name as the monitor type in the “Control Panel” of Windows 95/98. If your PC/graphics board has difficulty communicating with this monitor, load the Setup Disk and select this monitor’s model name as the monitor type. OK SCREEN CENTER If no picture appears on your screen • Check that the monitor is correctly connected to the computer. • If NO INPUT SIGNAL appears on the screen, confirm that your computer’s graphic board is completely seated in the correct bus slot. • If you are replacing an old monitor with this model and OUT OF SCAN RANGE appears on the screen, reconnect the old monitor. Then adjust the computer’s graphic board so that the horizontal frequency is between 30 – 109 kHz, and the vertical frequency is between 48 – 160 Hz. MENU L ANGUAGE ENGL I SH FRANÇA I S DEUT SCH ESPAÑOL I T A L I ANO NEDER L ANDS SVENSKA US 3 Move the control button m/M to select a language. • • • • • • • • • ENGLISH FRANÇAIS: French DEUTSCH: German ESPAÑOL: Spanish ITALIANO: Italian NEDERLANDS: Dutch SVENSKA: Swedish : Russian : Japanese To close the menu Press the center of the control button once to return to the main MENU, and twice to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds. IBM PC/AT or compatible computer to AC IN to a power outlet To reset to English Press the RESET button while the LANGUAGE menu is displayed on the screen. power cord (supplied) 6 7 Customizing Your Monitor You can make numerous adjustments to your monitor using the on-screen menu. 6 CONV (page 11) Select the CONV menu to adjust the picture’s horizontal and vertical convergence. CONVERGENCE x Using the control button 1 Display the main MENU. TOP BOT 26 Press the center of the control button to display the main MENU on your screen. MENU Navigating the menu Press the center of the control button to display the main MENU on your screen. See page 9 for more information on using the control button. 7 LANG (page 7) Select the LANG menu to choose the on-screen menu’s language. L ANGUAGE ENGL I SH FRANÇA I S DEUT SCH ESPAÑOL I T A L I ANO NEDER L ANDS SVENSKA Adjusting the brightness and contrast Brightness and contrast adjustments are made using a separate BRIGHTNESS/CONTRAST menu. These settings are stored in memory for all input signals. 1 Move the control button in any direction. The BRIGHTNESS/CONTRAST menu appears on the screen. BR I GHTNESS / CONTRAS T 2 Select the menu you want to adjust. MENU MENU OK SCREEN CENTER MENU CONV GEOM EXIT COLOR LANG SIZE OPTION 8 OPTION (page 13) Select the OPTION menu to adjust the monitor’s options. The options include: • degaussing the screen • changing the on-screen menu position • locking the controls OPT I ON DEGAUS S ON FRONT MENU x Displaying the current input signal 26 1-3 MENU OK SCREEN CENTER 2 SIZE (page 10) Selects the SIZE menu to adjust the picture’s size, centering or zoom. US BR I GHTNESS / CONTRAS T 3 Adjust the menu. Move the control button left (<) or right (,) to make the adjustment. MENU MENU 56 s RGB 76 : 56 76 For more information about using the sRGB mode, see “Adjusting the color of the picture (COLOR)” on page 12. CONV The menu automatically disappears after about 3 seconds. S I Z E / CENTER 26 3 GEOM (page 10) Select the GEOM menu to adjust the picture’s rotation and shape. ), and </, to adjust the contrast If you are using the sRGB mode The horizontal and vertical frequencies of the current input signal are displayed in the main MENU. If the signal matches one of this monitor’s factory preset modes, the resolution is also displayed. S I Z E / CENTER brightness ( (6). If you selected the sRGB mode in the COLOR menu, the following BRIGHTNESS/CONTRAST menu appears on the screen. REAR 1 CENTER (page 10) Selects the CENTER menu to adjust the picture’s centering, size or zoom. 26 2 Move the control button m/M to adjust the MENU 9 EXIT Select EXIT to close the menu. Use the control button to select one of the following menus. 26 Highlight the desired menu by moving the control button towards the rear to go up (M), towards the front to go down (m), and left (<) or right (,) to move sideways. the resolution of the current input signal GEOMETRY GEOM EXIT COLOR LANG SIZE OPTION 68 . 7kHz / 85Hz 1024 768 4 Close the menu. the horizontal and vertical frequencies of the current input signal Press the center of the control button once to return to the main MENU, and twice to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds. MENU 26 4 COLOR (page 12) Select the COLOR menu to adjust the picture’s color temperature. You can use this to match the monitor’s colors to a printed picture’s colors. COLOR EASY 5 SCREEN (page 11) Select the SCREEN menu to adjust the picture’s quality. You can adjust the landing and moire cancellation effect. 8 EXPERT 5 0 0 0K 6 5 0 0K s RG B 9 3 0 0K 5 0 0 0K x Resetting the adjustments Press the RESET button. See page 14 for more information on resetting the adjustments. SCREEN RESET L AND I NG 26 9 Adjusting the size of the picture (SIZE) Adjusting the shape of the picture (GEOM) This setting is stored in memory for the current input signal. The GEOM settings allow you to adjust the rotation and shape of the picture. The (rotation) setting is stored in memory for all input signals. All other settings are stored in memory for the current input signal. 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight SIZE and press the center of the control button again. The SIZE/CENTER menu appears on the screen. 3 First move the control button m/M to select for horizontal adjustment, or for vertical adjustment. Then move the control button </, to adjust the size. 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight GEOM and press the center of the control button again. The GEOMETRY menu appears on the screen. 3 First move the control button m/M to select the Adjusting the centering of the picture (CENTER) desired adjustment item. Then move the control button </, to make the adjustment. Select To This setting is stored in memory for the current input signal. rotate the picture 1 Press the center of the control button. expand or contract the picture sides The main MENU appears on the screen. 2 Move the control button to highlight 1-4 CENTER and press the center of the control button again. The SIZE/CENTER menu appears on the screen. shift the picture sides to the left or right adjust the picture width at the top of the screen shift the picture to the left or right at the top of the screen Adjusting the convergence (CONV) The CONV settings allow you to adjust the quality of the picture by controlling the convergence. The convergence refers to the alignment of the red, green, and blue color signals. If you see red or blue shadows around letters or lines, adjust the convergence. These settings are stored in memory for all input signals. 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight CONV and press the center of the control button again. The CONVERGENCE menu appears on the screen. 3 First move the control button m/M to select the desired adjustment item. Then move the control button </, to make the adjustment. Select To horizontally shift red or blue shadows vertically shift red or blue shadows Adjusting the quality of the picture (SCREEN) The SCREEN settings allow you to adjust the quality of the picture by controlling the moire and landing. • If the color is irregular at the corners of the screen, adjust the landing. • If elliptical or wavy patterns appear on the screen, cancel the moire. The CANCEL MOIRE and MOIRE ADJUST settings are stored in memory for the current input signal. All other settings are stored in memory for all input signals. 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight SCREEN and press the center of the control button again. The SCREEN menu appears on the screen. 3 First move the control button m/M to select the desired adjustment item. Then move the control button </, to make the adjustment. TOP V CONVER TOP vertically shift red or blue shadows at the top of the screen Select To BOT V CONVER BOTTOM vertically shift red or blue shadows at the bottom of the screen LANDING reduce any color irregularities in the screen’s top left corner to a minimum. LANDING reduce any color irregularities in the screen’s top right corner to a minimum. LANDING reduce any color irregularities in the screen’s bottom left corner to a minimum. Enlarging or reducing the picture (ZOOM) LANDING reduce any color irregularities in the screen’s bottom right corner to a minimum. This setting is stored in memory for the current input signal. CANCEL MOIRE* 3 First move the control button m/M to select for horizontal adjustment, or for vertical adjustment. Then move the control button </, to adjust the centering. 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight SIZE or CENTER and press the center of the control button again. The SIZE/CENTER menu appears on the screen. 3 Move the control button m/M to select (zoom), and move </, to enlarge or reduce the picture. MOIRE ADJUST turn the moire cancellation function ON or OFF. (MOIRE ADJUST) appears in the menu when you select ON. adjust the degree of moire cancellation until the moire is at a minimum. • Moire is a type of natural interference which produces soft, wavy lines on your screen. It may appear due to interference between the pattern of the picture on the screen and the phosphor pitch pattern of the monitor. Example of moire Note Adjustment stops when either the horizontal or vertical size reaches its maximum or minimum value. Note The picture may become fuzzy when CANCEL MOIRE is set to ON. 10 11 US Adjusting the color of the picture (COLOR) The COLOR settings allow you to adjust the picture’s color temperature by changing the color level of the white color field. Colors appear reddish if the temperature is low, and bluish if the temperature is high. This adjustment is useful for matching the monitor’s color to a printed picture’s colors. These settings are stored in memory for all input signals. EXPERT mode sRGB mode You can make additional adjustments to the color in greater detail by selecting the EXPERT mode. The sRGB color setting is an industry standard color space protocol designed to correlate the displayed and printed colors of sRGB compliant computer products. To adjust the colors to the sRGB profile, simply select the sRGB mode in the COLOR menu. However, in order to display the sRGB colors correctly (γ=2.2, 6500K), you must set your computer to the sRGB profile and adjust the brightness ( ) and contrast (6) to the numbers shown in the menu. For information on how to change the brightness ( ) and contrast (6), see page 9. COLOR EASY EXPERT 5 0 0 0K 6 5 0 0K R B I AS G B I AS B B I AS R GA I N G GA I N B GA I N s RG B 9 3 0 0K 50 50 50 50 50 50 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight COLOR and press the center of the control button again. The COLOR menu appears on the screen. 3 Move the control button </, to select the adjustment mode. There are three types of adjustment modes, EASY, EXPERT and sRGB. 4 First move the control button m/M to select the desired adjustment item. Then move the control button </, to make the adjustment. Adjust the selected mode according to the following instructions. EASY mode COLOR 1-5 EASY 5 0 0 0K EXPERT 6 5 0 0K s RG B 9 3 0 0K 5 0 0 0K 1 Move the control button m/M to select the color temperature row 1. Then move the control button </, to select a color temperature. 2 Move the control button m/M to select the adjustment item 2. Then move the control button </, to adjust the BIAS (black level). This adjusts the dark areas of an image. 3 Move the control button m/M to select the adjustment item 3. Then move the control button </, to adjust the GAIN (white level). This adjusts the light areas of an image. You can adjust the R (red), G (green), B (blue) component of the input signal when making changes to items 2 and 3. If you fine tune the color temperature, the new color settings are stored in memory for each of the three color temperatures and item 1 of the on-screen menu change as follows. • [5000K]t[ 1] • [6500K]t[ 2] • [9300K]t[ 3] Note Your computer and other connected products (such as a printer), must be sRGB compliant. COLOR EASY : 56 EXPERT s RG B : 7 6 FOR s RG B Additional settings (OPTION) You can manually degauss (demagnetize) the monitor, change the menu position, and lock the controls. 1 Press the center of the control button. The main MENU appears on the screen. 2 Move the control button to highlight OPTION and press the center of the control button again. The OPTION menu appears on the screen. 3 Move the control button m/M to select the desired adjustment item. Adjust the selected item according to the following instructions. Degaussing the screen The monitor is automatically demagnetized (degaussed) when the power is turned on. To manually degauss the monitor, first move the control button m/M to select (DEGAUSS). Then move the control button ,. The screen is degaussed for about 2 seconds. If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. US Changing the menu’s position Change the menu’s position if it is blocking an image on the screen. To change the menu’s on-screen position, first move the control button m/M to select (OSD H POSITION) for horizontal adjustment, or (OSD V POSITION) for vertical adjustment. Then move the control button </, to shift the on-screen menu. Locking the controls 1 Move the control button m/M to select the color temperature row 1. Then move the control button </, to select a color temperature. The preset color temperatures are 5000K, 6500K, and 9300K. Since the default setting is 9300K, the whites will change from a bluish hue to a reddish hue as the temperature is lowered to 6500K and 5000K. 2 If necessary, fine tune the color temperature. To protect adjustment data by locking the controls, first move the control button m/M to select (CONTROL LOCK). Then move the control button ,, to select ON. Only the 1 (power) switch, EXIT, and (CONTROL LOCK) of the OPTION menu will operate. If any other items are selected, the mark appears on the screen. To cancel the control lock Repeat the procedure above and set (CONTROL LOCK) to OFF. Move the control button m/M to select the color temperature row 2. Then move the control button </, to fine tune the color temperature. If you fine tune the color temperature, the new color settings are stored in memory for each of the three color temperatures and item 1 of the on-screen menu changes as follows. • [5000K]t[ 1] • [6500K]t[ 2] • [9300K]t[ 3] 12 13 Resetting the adjustments This monitor has the following three reset methods. Use the RESET button to reset the adjustments. RESET Resetting a single adjustment item Use the control button to select the adjustment item you want to reset, and press the RESET button. Resetting all of the adjustment data for the current input signal Press the RESET button when no menu is displayed on the screen. Note that the following items are not reset by this method: • on-screen menu language (page 7) • adjustment mode in the COLOR menu (EASY, EXPERT, sRGB) (page 12) • on-screen menu position (page 13) • control lock (page 13) 1-6 Resetting all of the adjustment data for all input signals Press and hold the RESET button for more than two seconds. Note The RESET button does not function when (CONTROL LOCK) Technical Features Troubleshooting Before contacting technical support, refer to this section. Preset and user modes When the monitor receives an input signal, it automatically matches the signal to one of the factory preset modes stored in the monitor’s memory to provide a high quality picture at the center of the screen. (See Appendix for a list of the factory preset modes.) For input signals that do not match one of the factory preset modes, the digital Multiscan technology of this monitor ensures that a clear picture appears on the screen for any timing in the monitor’s frequency range (horizontal: 30 – 109 kHz, vertical: 48 – 160 Hz). If the picture is adjusted, the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received. Note for Windows users If thin lines appear on your screen (damper wires) The lines you are experiencing on your screen are normal for the Trinitron monitor and are not a malfunction. These are shadows from the damper wires used to stabilize the aperture grille and are most noticeable when the screen’s background is light (usually white). The aperture grille is the essential element that makes a Trinitron picture tube unique by allowing more light to reach the screen, resulting in a brighter, more detailed picture. Damper wires On-screen messages If there is something wrong with the input signal, one of the following messages appears on the screen. If NO INPUT SIGNAL appears on the screen I NFORMA T I ON MON I TOR I S WORK I NG I NPUT : 6 8 . 7 kHz / NO I NPUT S I GNA L 8 5H z WH I T E RED GREEN B L UE 1 The frequencies of the current input signal If the monitor recognizes the frequencies of the current input signal, the horizontal and vertical frequencies are displayed. For Windows users, check your video board manual or the utility program which comes with your graphic board and select the highest available refresh rate to maximize monitor performance. 2 The input signal condition NO INPUT SINGAL This indicates that no signal is input. Power saving function If OUT OF SCAN RANGE appears on the screen This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below. Power mode Power consumption 1 (power) indicator normal operation ≤ 145 W green 1 standby ≤ 15 W green and orange alternate 2 suspend (sleep)* ≤ 15 W green and orange alternate 3 active off** (deep sleep)* Approx. 1 W orange power off 0W off is set to ON. * “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency. ** When your computer enters a power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters a power saving mode. I NFORMA T I ON MON I TOR I S WORK I NG I NPUT : 1 3 0 . 0 kHz / US 7 5H z OUT OF SCAN RANGE CHANGE S I GNA L T I M I NG WH I T E RED GREEN B L UE 1 The frequencies of the current input signal If the monitor recognizes the frequencies of the current input signal, the horizontal and vertical frequencies are displayed. 2 The input signal condition OUT OF SCAN RANGE This indicates that the input signal is not supported by the monitor’s specifications. 3 The remedies CHANGE SIGNAL TIMING appears on the screen. If you are replacing an old monitor with this monitor, reconnect the old monitor. Then adjust the computer’s graphic board so that the horizontal frequency is between 30 - 109 kHz, and the vertical frequency is between 48 - 160 Hz. For more information, see “Trouble symptoms and remedies” on page 16 14 15 Trouble symptoms and remedies If the problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual. Use the self-diagnosis function (page 18) if the following recommendations do not resolve the problem. Symptom Check these items No picture If the 1 (power) indicator is not lit • Check that the power cord is properly connected. • Check that the 1 (power) switch is in the “on” position. If the NO INPUT SIGNAL message appears on the screen, or if the 1 (power) indicator is either orange or alternating between green and orange • Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets. (page 6). • Check that the HD15 video input connector’s pins are not bent or pushed in. If the OUT OF SCAN RANGE message appears on the screen xProblems caused by the connected computer or other equipment • The computer is in power saving mode. Try pressing any key on the computer keyboard or moving the mouse. • Check that the computer’s power is “on.” • Check that the graphic board is completely seated in the proper bus slot. xProblems caused by the connected computer or other equipment • Check that the video frequency range is within that specified for the monitor. If you replaced an old monitor with this monitor, reconnect the old monitor and adjust the frequency range to the following. Horizontal: 30 – 109 kHz Vertical: 48 – 160 Hz If no message is displayed and the 1 (power) indicator is green or flashing orange • Use the Self-diagnosis function (page 18). If using Windows 95/98 • If you replaced an old monitor with this monitor, reconnect the old monitor and do the following. Install the Setup Disk (page 7) and select this monitor (“CPD-E500”) from among the Sony monitors in the Windows 95/98 monitor selection screen. 1-7 If using a Macintosh system Picture flickers, bounces, oscillates, or is scrambled • Check that the supplied Macintosh adapter and the video signal cable are properly connected (page 6). • Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions. • Move the monitor away from power lines or place a magnetic shield near the monitor. • Try plugging the monitor into a different AC outlet, preferably on a different circuit. • Try turning the monitor 90° to the left or right. Symptom Check these items Picture is ghosting • Eliminate the use of video cable extensions and/or video switch boxes. • Check that all plugs are firmly seated in their sockets. Picture is not centered or sized properly • Adjust the size (page 10) or centering (page 10). Note that some video modes do not fill the screen to the edges. Edges of the image are curved • Adjust the geometry (page 10). Wavy or elliptical pattern (moire) is visible • Set CANCEL MOIRE to ON and adjust the degree of moire cancellation until the moire is at a minimum (page 11). xProblems caused by the connected computer or other equipment • Change your desktop pattern. Color is not uniform • Degauss the monitor* (page 13). If you place equipment that generates a magnetic field, such as a speaker, near the monitor, or if you change the direction the monitor faces, color may lose uniformity. • Adjust the landing (page 11). White does not look white • Adjust the color temperature (page 12). Letters and lines show red or blue shadows at the edges • Adjust the convergence (page 11). Monitor buttons do not operate ( appears on the screen) • If the control lock is set to ON, set it to OFF (page 13). A hum is heard right after the power is turned on • This is the sound of the auto-degauss cycle. When the power is turned on, the monitor is automatically degaussed for two seconds. * If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a malfunction. Displaying this monitor’s name, serial number, and date of manufacture. While the monitor is receiving a video signal, press and hold the center of the control button for more than five seconds to display this monitor’s information box. MENU US If the problem persists, call your authorized Sony dealer and give the following information. • Model name: CPD-E500 • Serial number • Name and specifications of your computer and graphics board. Example INFORMATION b MODEL : CPD E500 SER NO : 1234567 MANUFACTURED : 1999-52 xProblems caused by the connected computer or other equipment • Check your graphics board manual for the proper monitor setting. • Confirm that the graphics mode (VESA, Macintosh 21" Color, etc.) and the frequency of the input signal are supported by this monitor (Appendix). Even if the frequency is within the proper range, some graphics boards may have a sync pulse that is too narrow for the monitor to sync correctly. • Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture. Picture is fuzzy 16 • Adjust the brightness and contrast (page 9). • Degauss the monitor* (page 13). • If CANCEL MOIRE is ON, the picture may become fuzzy. Decrease the moire cancellation effect or set CANCEL MOIRE to OFF (page 11). 17 Self-diagnosis function This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer, the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard. MENU RESET Specifications CRT Viewable image size Resolution Maximum Recommended 1 (power) indicator Standard image area If the 1 (power) indicator is green 1 Disconnect the video input cable or turn off the connected computer. Deflection frequency* 2 Press the 1 (power) button twice to turn the monitor off and then on. AC input voltage/current Power consumption Dimensions 3 Move the control button , for 2 seconds before the monitor enters power saving mode. 1-8 MENU If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cable and check the condition of your computer. If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition. If the 1 (power) indicator is flashing orange Press the 1 (power) button twice to turn the monitor off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board. 18 Mass Plug and Play Supplied accessories 0.24 mm aperture grille pitch 21 inches measured diagonally 90-degree deflection FD Trinitron Approx. 403.8 × 302.2 mm (w/h) (16 × 12 inches) 19.8" viewing image Horizontal: 2048 dots Vertical: 1536 lines Horizontal: 1600 dots Vertical: 1200 lines Approx. 388 × 291 mm (w/h) (15 3/8 × 11 1/2 inches) or Approx. 364 × 291 mm (w/h) (14 3/8 × 11 1/2 inches) Horizontal: 30 to 109 kHz Vertical: 48 to 160 Hz 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A Approx. 145 W Approx. 497 × 480 × 478 mm (w/h/d) (19 5/8 × 19 × 18 7/8 inches) Approx. 32 kg (70 lb 9 oz) DDC1/2B/2Bi, GTF** See page 6 * Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.3 µsec. • Vertical blanking width should be more than 450 µsec. ** If the input signal is Generalized Timing Formula (GTF) compliant, the GTF feature of the monitor will automatically provide an optimal image for the screen. Design and specifications are subject to change without notice. CPD-E500/E500E SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL Push in the tip of a screwdriver about 5mm to unlock the claw. Cabinet Cabinet 5 6 Four screws (+ BVTT 4 x 8) Bezel assembly 3 Bezel assembly Two claws Top cover 4 2 3 7 8 Two claws Three screws (+ BVTT 4 x 8) Cabinet Two screws (+ BVTP 4 x 16) 1 Pig tail cover CPD-E500 (U/C) Video shield 2-2. D BOARD REMOVAL 3 Screw (+ P 3.5 x 20) 5 D board 4 Two screws (+ BVTP 3 x 12) 1 Three screws (+ BVTT 4 x 8) B GND CN504 CN505 Two hooks 2 2-1 A Open the D block in the direction of the arrow A . and remove of the arrow B . CPD-E500/E500E 2-3. G BOARD REMOVAL 3 Four screws (+BVTP 3 x 8) 4 1 Three screws (+ BVTT 4 x 8) CN654 CN653 CN652 G shield CN602 6 B G board CN650 7 GND GND 8 Two screws (+ BVTP 3 x 8) AC inlet (3P) A Two hooks 2 Open the G block in the direction of the arrow A . and remove of the arrow B . 5 2-2 Two printed circuit board holders CPD-E500/E500E 2-4-1. A BOARD, I/O TERMINAL BOARD ASSEMBLY REMOVAL (CPD-E500E) 4 A board (2/2) 3 A board (1/2) 1 When installing I/O terminal board assembly, be sure to apply screw lock on 2 spots after screws (HD15) are fixed. Three screws (+BVTT 4 x 8) A board (1/2) 2 Screw (M4) (EXT tooth washer) A board (1/2) Screw lock 6 5 Terminal bracket Two screws (HD15) 2-4-2. A BOARD, TERMINAL BRACKET REMOVAL (CPD-E500) 4 A board (2/2) 3 A board (1/2) 1 Three screws (+BVTT 4 x 8) A board (1/2) 2 5 2-3 Screw (M4) (EXT tooth washer) Terminal board bracket CPD-E500/E500E 2-5. N BOARD REMOVAL CPD-E500 (U/C) CN5003 CN5002 CN001 CN5001 CN002 CN010 CN011 CN007 2 1 N board Printed circuit board holder 2-6. SERVICE POSITION CAUTION : SHORT D,G boards Rear shield If the claw is hooked, opening and closing the board is impossible. Do not try to do it by force. D board (Refer to 2-2.) If the claw is hooked, opening and closing the board is impossible. Do not try to do it by force. CN602 G board (Refer to 2-3.) AC inlet (3P) 2-4 CPD-E500/E500E 2-7. BEZEL ASSEMBLY, H1 BOARD REMOVAL 1 Before removing the bezel assembly, secure the picture tube by attaching two screws to the picture tube shield at the positions shown with an arrow (diagonal two places) to prevent the picture tube from falling. (Use the screws +BVTT 4 x 8 that fix top cover.) 2 Four screws (Tapping screw 5) Picture tube shield 7 H1 board CN801 4 8 3 Menu button Two screws (+ BVTP 4 x 16) 6 Two H printed circuit board brackets 5 H printed circuit board cover Bezel assembly 2-8. PICTURE TUBE REMOVAL 6 1 Open the D block. (Refer to 2-2.) Four screws (Tapping screw 5) 3 10 5 A board Deflection yoke Anode cap (See page 2-6.) 2 CN4 CN5 4 CN801 8 7 Neck assembly Three connectors 9 GND Picture tube Bezel assembly 2-5 Open the G block. (Refer to 2-3.) CPD-E500/E500E 2-9. J BOARD REMOVAL 1 2 Two screws (+BVTT 4 x 8) Remove the picture tube. (Refer to 2-8.) 4pin GND 2pin CN601 4pin J board 5 3 CN891 Picture tube shield complete assembly. Two hooks 4 Claw • REMOVAL OF ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode. • REMOVING PROCEDURES c b a Anode Button 1 Turn up one side of the rubber cap in the direction indicated by the arrow a. 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b. • HOW TO HANDLE AN ANODE-CAP 1 Don’t scratch the surface of anode-caps with sharp shaped material! 2 Don’t press the rubber hardly not to damage inside of anodecaps! A material fitting called as shatter-hook terminal is built in the rubber. 3 Don’t turn the foot of rubber over hardly! The shatter-hook terminal will stick out or damage the rubber. 2-6 3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling up it in the direction of the arrow c. CPD-E500/E500E 2-10-1. HARNESS LOCATION (CPD-E500E) H1 board J board Picture tube CN891 CN801 CN5 4pin 4pin CN4 CN5003 CN509 CN502 CN5002 CN602 CN654 CN508 CN505 CN001 FBT CN504 CN5001 CN010 CN653 CN007 CN603 CN652 CN011 CN601 CN650 CN506 CN501 AC inlet D board N board Rear shield Terminal bracket CN401 CN403 CN405 CN407 CN408 A board 2-7 CN406 G board CPD-E500/E500E 2-10-2. HARNESS LOCATION (CPD-E500) H1 board J board Picture tube CN891 CN801 CN5 4pin 4pin CN4 CN5003 CN5002 CN602 CN654 CN508 CN505 CN509 CN502 CN002 CN001 FBT CN504 CN5001 CN010 CN653 CN007 CN603 CN652 CN011 CN601 CN650 CN506 CN501 AC inlet D board N board Rear shield Terminal board bracket CN402 CN403 CN405 CN407 CN408 A board 2-8 CN406 G board CPD-E500/E500E SECTION 3 SAFETY RELATED ADJUSTMENT When replacing or repairing the shown below table, the following operational checks must be performed as a safety precaution against X-rays emissions from the unit. c) Beam Current Protector Circuit Check (1st Protector): D Board 1) Apply 4.5 V DC to CN504 0 pin on the D board, and check high voltage value. 2) Connect constant current source to a section between T902 (FBT) qa pin and qs pin (GND) on the D board, and check that high voltage checked in 1) lowers by 1.50 kV or more when the specified current flows to the qa pin. [Specification]: 2.00 +0.00/–0.01 mA Part Replaced ([) HV ADJ RV901 Part Replaced (]) HV Regulator Circuit Check D Board C920, IC901, R923 R924, R929, R945, RV901, T902(FBT) • Mounted D Board HV Protector Circuit Check D Board C922, C925, C926, D912, D914, D915, D921, Q907, Q908, R921, R922, R932, R937, R939, T902(FBT) • Mounted D Board Beam Current Protector Circuit Check d) Beam Current Protector Circuit Check (2nd Protector): D Board 1) Connect constant current source to a section between T902 (FBT) qa pin and qs pin (GND) on the D board, and check that the voltage of CN504 0 pin becomes 0 V or less when the specified current flows to the qa pin. [Specification]: 1.70 +0.00/–0.01 mA D Board C910, C921, C933, D901, D902, D913, IC503, IC901, R901, R920, R928, R930, R931, R940, R941, T902(FBT) • Mounted D Board G Board IC652 • Mounted G Board N Board IC001, R031, R032 • Mounted N Board e) Beam Current Protector Circuit Check : G Board 1) Apply 264 V AC. 2) Enter about 5 V to CN650 4 pin on the G board, and check that the output voltage of CN653 2 pin is about 15 V. 3) Enter about 0±0.2 V to CN654 4 pin, and check that the output voltage of CN653 2 pin becomes 1.0 V or less. * Confirm one minute after turning on the power. a) HV Regulator Circuit Check 1) Enter black crosshatch signal (black on white background), and check that high voltage is in the specified range. [Specification]: 27.00 ±0.10 kV 2) Check that the voltage of D912 cathode on the D board is 27.0 V or more. f) Beam Current Protector Circuit Check : N Board 1) Check that the protector operates, when the voltage of CN010 qh pin on the N board is lowered to 0 V or less (for more than 2 seconds). b) HV Protector Circuit Check 1) Enter black crosshatch signal (black on white background). 2) Apply the specified voltage to the D912 cathode on the D board, and check that high voltage is 0.1 kV or less. [Specification]: 31.90 +0.00/–0.05 V 3-1 CPD-E500/E500E SECTION 4 ADJUSTMENTS Note: Hand degauss must be used on stand-by or power-off condition. This model has an automatic earth magnetism correction function by using an earth magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimes gets magnetized, and the system may not work properly as a result. • Landing Rough Adjustment 1. Enter the full white signal. (or the full black dots signal). 2. Adjust the contrast to the maximum. 3. Make the screen monogreen. Note: Off the outputs from R ch and B ch of SG. 4. Reverse the DY, and adjust coarsely the purity magnet so that a green raster positions in the center of screen. 5. Adjust the tilt of DY, and fix lightly with a clamp. Note: “TILT” = “128”. • Write terrestrial magnetism sensor reading VX and VY to “LCC VX” and LCC VY” respectively. Adjust the landing by moving “LCC NS”, “LCC LT”, “LCC LB”, “LCC RT” and “LCC RB”. However, the register adjustment must be limited within the following range. “LCC NS” 128 ± 15 “LCC LT”, “LCC LB”, “LCC RT”, “LCC RB” 128 ± 40 Save the service data. • Landing Fine Adjustment 1. Put the set inside the Helmholtz coil. (“LCC SW” = “12”) 2. Input the single green signal and set the “CONTRAST”= “255”. Note: After the W/B adjustment with 9300K, measure an average of ΣIk when a full white signal is entered in the CONT MAX/BRT CENT status. Then make adjustment so that the specified screen can be attained after aging for 2 hours with Ik equivalent to 30% of the average value. 3. Demagnetize the metal part of the chassis with the hand degausser and coil degausser, and the CRT surface with the hand degausser. Input AC 230V to AC IN, turn on and off the power to perform auto degaussing. (Perform auto degaussing by setting “FUNCTION SW”=1. Return to the original value after use.) Demagnetize the CRT surface with the hand degausser again. Note: (1) Hand degauss must be used on stand-by or power-off condition. This model has an automatic earth magnetism correction function by using an earth magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimes gets magnetized, and the system may not work properly as a result. (2) Adjust in a non-magnetic field. (3) If adjusting in a magnetic fields, add the shift from the nonmagnetic field in your estimation. 4. Attach the wobbling coil to the designated part of the CRT neck. 5. Attach the sensor of the landing adjustment unit on the CRT surface. 6. Adjust the DY position and purity, and the DY tilt, and landing of the center and 4 corners with the landing checker. After adjustment, set “LCC SW” to “13”. <Specifications> Adjust so that the green is within the specification given right. 4 corner adjust target : within ± 1 The red and blue must be within the specification given right with respect to the green. A difference between red and blue must be within the specification given right. (µm) 0 ± 3 0 ± 7.5 0 ± 3 0 ± 3 0 ± 7.5 0 ± 3 0 ± 3 0 ± 7.5 0 ± 3 ±6 ±6 (µm) ±6 ±6 ±6 ±6 ±6 ±6 ±6 10 10 (µm) 10 10 7 10 10 10 10 * Adjustment and measurement should be made at the points one inch inside the fluorescent screen. 7. Tighten DY screw Note: Torque 22 ± 2 kg•cm (2.2 ± 0.2 Nm) autodegauss it. 8. For the up/down swing, swing the DY and insert a wedge so that the up and down pins are equal at the top and bottom. Adjust the H.TRP VR of DY so that the horizontal trapezoid is equal at the left and right. Insert the wedge firmly so that the DY does not shake. 9. Check the landing of each corner, and if it does not satisfy the specification, adjust the landing of four corners using “LCC LT“, “LCC LB”, “LCC RT” and “LCC RB”. However, the register adjustment must be limited within the following range. “LCC NS” 128 ± 15 “LCC LT”, “LCC LB”, “LCC RT”, “LCC RB” 128 ± 40 After adjustment, save the service data. 10. Remove the sensor and wobbling coil. 11. Switch the signal to R.G.B., and check that each color is pure. 12. Check that the DY is not tilting, and fix the purity Mg with a white pen. Fix wedges with RTV. 4-1 CPD-E500/E500E Connect the communication cable of the computer to the connector located on the D board. Run the service software and then follow the instruction. 1 1-690-391-21 2 A-1500-819-A Interface Unit 3 3-702-691-01 Connector Attachment IBM AT Computer as a Jig To BUS CONNECTOR D-sub (9 Pin [female]) mini Din (8Pin) *The parts above ( 1 4 Pin 4 Pin 3 ) are necessary for DAS adjustment. • Convergence Rough Adjustment (1) Receive an image of the white crosshatch signals (white lines on black). (2) Place the protrusions of the 6-fold poles magnet attached to the CRT neck upon each other. (3) Make rough adjustment of the H and V direction convergence by using 4-fold poles magnet. • White Balance Adjustment Specification 1. 9300K x=0.283 ± 0.005 y=0.298 ± 0.005 (All White) 2. 6500K x=0.313 ± 0.005 y=0.329 ± 0.005 (All White) 3. 5000K x=0.346 ± 0.005 y=0.359 ± 0.005 (All White) Purity 4-pole magnet 6-pole magnet YCH H-TRP YBH 4 Pin 2-pole magnet TLH • Vertical and Horizontal Position and Size Specification A b APH XBV b XCV B a * Set so that the protruding parts of the 2 magnet rings agree with each other. XCV a b B 4:3 5:4 A 388 364 B 291 291 2.0 mm 2.0 mm • Focus adjustment Adjust the focus volume 1 and 2 for the optimum focus. TLH XBV R B R TLV a MODE B B R YCH R YBH R B B R R B R B Focus 1 • Convergence Specification Focus 2 B V A fH 60kHz 60kHz> A 0.20 mm 0.24 mm B 0.24 mm 0.28 mm FBT 4-2 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS CN402 2 9 1 7 INPUT INPUT 12 7 A 11 6 TO N BOARD CN002 RIN2 GOUT BOUT BIN1 GIN1 B1 TO N BOARD CN001 B2 TO N BOARD CN001 21 DDC SCL 1 19 DDC +5V 1 18 VS1 17 HS/VS1 16 DDC SDA 1 20 G. SYNC DET 7 SYNC ON G 6 CLP 2 C. BLK 4 SCL 13 SDA 14 H. SYNC 25 RXD 18 3 RXD TXD 20 4 TXD +15V 24 +15V 25 2 +15V –15V 22 4 –15V –15V 23 1 +12V HDF 14 6 +80V VDF 12 ABL 10 HV DET 8 S0 7 H CENT 6 S6 5 HSPBAL 4 HLINBAL 3 H SIZE 2 H SHAPE 1 2 VDF TO G BOARD CN653 F TO G BOARD CN654 HV DET S0 17 25 CLP 21 C. BLK 30 D/A5 SCL 22 H. SYNC 5 V. SYNC 6 HFBP 7 D/A4 CLP D/A3 BLK D/A2 SCL SDA 4 9 13 1 17 18 19 20 21 8 SCL 26 15 27 14 28 13 15 16 XT1 XT0 1 8 4 5 H OUT, BUFF Q515, 520 CN508 +220V 5 +220V 4 H CENT L 3 H CENT N 2 H CENT H 1 IC502 H CENT OUT H CENT H 5 H DRV Q502, 503 HSP HDIN 3 ECO SW 14 4 PWR SW DGUS SW 12 5 DGUS SW HTR SW 10 6 HTR SW TH DET 25 +VIN OUT 2 4 V RET 3 VSHAPE 1 +12V 4 1 STBY+5V 2 1W+5V +80V 4 +80V +220V 6 +220V +12V 8 +12V 1 G2 1 G2 5V 5V-2 17 DRIFT CORRECT Q401 10 PS401 1A IC405 (1/2) – + 7 G2 CONT Q406, 407, 410 CN506 HV REG SW Q905 +220V HDIN PWMOUT H ERRIN 3 12 – + HVD 11 T902 FBT 5 HV DRV Q903, 904 HV OUT Q906 2 PIN OUT Q508 17 RV901 HV DET H DRV Q701-705 2 11 5 PIN AMP Q524 HFBP +15V HD +12V 7 8 O2 14 14 5 15 7 IC701 V DY OUT V RET 3 V SHAPE 5 OUT VCC – +12V + OUT 4 11 2 V+ V– CN509 2 1 V– 3 5 V+ O4 O3 9 3 VSHAPE Q523 –4 HL OUT Q516, 518 14 13 HLIN 3 2 4 1 V RET FV FV 6 HV DET Q907, 908 +80V –15V FC 16 S5 S1 HV ADJ FC T503 HST GAIN SW Q526 S5-1 HV HV 1 2 T701 DFT L505 HOC +220V S3 T901 HRC 3 15 V DRV Q706, 707 PIN DRV Q504, 505 6 TO G BOARD CN650 2 5 ERROUT 5 PWMOUT S4 S2 IC503 AMP S0-4, S6 S CAP CHANGE Q501, 506, 507, 510-513, 517, 525 2 V. DY C 3 V. DY H 9 H. DY H 10 H. DY H 5 H. DY C 6 H. DY C 1 T505 HLC S5 RY501 S5 RELAY DRV Q519 B-SS3525<U/C>-BD1-EPS05 5-1 E TO G BOARD CN652 6 IC901 HV CONTROL HDF O1 6 HEATER X401 8MHz 12 10 14 +1 8 HD 9 11 VDF ABL DET HFBP 7 –VIN ABL 19 11 5 5 –3 S1 1 HEATER+ 7 11 H SIZE 21 24 T502 HCT HSP 22 KB HEATER+ 5 GND 14 TH DET TH DET Q521, 522 +12V VEE S5-1 23 TH DET BOUT HD IC501 PIN CONTROL H SIZE 16 GOUT VCC H CENT L 3 H CENT Q514 PWR SW KB 7 +220V HLIN ECO SW 1 V901 PICTURE TUBE CN405 BIN BUFFER Q101, Q201, Q301 14 H OUT Q509 HSPBAL 1W+5V 3 3 ROUT GIN HFBP CN502 S5 25 GCI PWM1 IC404 OSD Hfly T501 HDT H CENT H 2 2 KG CN406 26 RCI VDD (DEFLECTION) S6 18 KG 17 BCI VS RIN 12 SDA VCC KICK Q402 H CENT N 1 1W+5V 4 5 3 IC406 CUTOFF AMP SYNC SEP OUT H CENT STBY+5V S3 BOUT 6 KR (VIDEO AMP, RGB OUT) D G 1 24 BIN 19 10 ECS ABL DET 20 S4 GOUT ABL HDF STBY+5V S2 33 GIN KR G. DET S5 TO N BOARD CN011 8 CN501 CN505 D BOUT 38 CN408 5 G2 SDA 3 HSPBAL TO N BOARD CN010 STBY+5V GOUT BIN SCL 4 H CENT C 2 11 GIN SDA 23 CN503 16 29 IC407 A 14 21 G DET IN 5V CN504 6 9 HFBP STBY+5V 32 8 V. SYNC CN407 ROUT 23 R DET IN RIN1 V-DET HOST GND 1 RIN GIN2 B DET IN 14 CN403 12 HV 11 41 FC 13 8 3 ROUT BIK 4 RIN GIK CONNECTOR PANEL 1 10 14 9 2 RIK CN401 HD15 5 35 ROUT PWM4 15 BIN2 PWM3 3 PWM2 5 [ AEP ] 6 11 V-DET 7 12 OSD BLK 8 13 IC403 RGB AMP IC402 RGB DRIVE AV 9 14 1 2 OSD R 10 15 3 ROUT 4 FV IC401 INPUT SELECT 5 OSD B 6 FBLK 4 RIN2 OSD G 2 GIN2 BOUT BIN2 GOUT [ U/C ] 5-2 V. DY H. DY µ-COM, V.CONV, H. CONV, LCC, GEO MAGNETIC SENSOR N UIN4 IC012 ROM P54/INT4 DDC SDA 1 2 HS/CS 1 6 VS 1 5 HOST GND 1 1 DET1 UPWM19 46 47 HS1 104 VC1 103 29 UBI1 UPWM22 UBI2 UPWM20 UIN2 UPWM18 UIN1 P52/INT2 UPWM13 CLP 20 C. BLK 18 SYNC ON G 16 G. SYNC DET 15 SCL 9 SDA 8 H. SYNC 14 V. SYNC 13 HFBP 12 53 51 108 SOG DET D SCL 41 D SDA 42 HSOUT 98 VS OSD UOUT3 UPWM9 UOUT7 SDA1 HV DET 18 H CENT 20 HSPBAL 22 HLINBAL 23 HSIZE 24 HSHAPE 25 TXD 6 RXD 8 +15V 1 +15V 2 +15V –15V 3 +15V –15V 4 STBY+5V 10 S0 19 128 86 138 126 144 136 133 45 44 AIN12 P90 DAC0 RESET 61 21 Q012 UPWM12 2 S3 3 S5 4 S2 5 S1 7 TH DET 1 PWR SW 12 DGUS SW 14 HTR SW 16 VRET 23 ECO SW 10 58 60 56 55 88 15, 94 95 93 92 UPWM15 P10/A0 UPWM11 P11/A1 UPWM10 AIN1 TXD AIN2 HFBP 18 HD 20 VSHAPE 25 +12V 22 +12V STBY+5V 6 STBY+5V 1W+5V 8 1W+5V HD VSP X001 24.756MHz 64 8 LCC-RB (–) 5 LCC-RT (+) 6 LCC-RT (–) 1 LCC-NS (+) 2 LCC-NS (–) 5 ROTATION (+) 6 ROTATION (–) 3 H CONV (+) 4 H CONV (–) 1 V CONV (+) 2 V CONV (–) 6 1W+5V 7 STBY+5V 1 LED0 2 LED1 3 KEY DET 8 ENV DRI PA0 PA6 PA4 P12/A2 UOUT8 PA3 UPWM4 PA5 UPWM3 PA2 UPWM5 PA1 AIN11 P42/D2, P93 UPWM2 UPWM1 AIN13 P94 P95 P92 UOUT5 INT1 6 131 LCC-RB LCC-RT CN5003 + – 7 8 IC5201 (1/2) 4 2 IC5401 (2/2) 83 6 84 + – 7 39 5 38 6 40 7 LCC-NS CN5001 + – 3 8 ROTATION H. CONV V. CONV IC5401 (1/2) SDA 4 SCL + – 3 IC002 WDT WC 33 3 34 8 2 CK RESET SW Q008 1W+5V +15V STBY+5V 3 LED0 LED0 4 LED1 LED1 76 KEYDET KEY DET 77 ENV ENV UIN6 ACTIVE OFF DET Q004-006 19 8 ECO SW Q007 5 18 IC010 H. V. OSC, AFC, H. DRV, V. SHAPE 124 99 1 13 HD SW Q011 HC1 25 120 35 117 34 122 33 114 29 111 27 90 13 96 9 67 5 109 8 66 4 AFC FIL HD DUTY 3 VC1 11 14 1CLR 1Q 5 2CLR 1CK 2CK 2Q 9 BSHPLVL IC004 ECO DET DVSHAPE VDC REG9V 21 CURRENT MILLER Q001-003 +12V [ AEP ] HPHASE HFREQ 1 HPLL 13 AFC SW VSH HS FBP HD VSAWRST VSHAPE 1CLR 1Q 5 2CLR 30 15 HC2 6 VC2 11 3 1CK 2CK 2Q 9 XTB IC005 ECO DET XTD B-SS3525<U/C>-BD2-EPS05 5-3 LCC-LT 2 RXD UOUT4 63 LCC-RB (+) IC5201 (2/2) 148 14 UPWM7 ECO SW HFBP LCC-LT (–) 7 140 P41/D1 UPWM6 59 2 LCC-LB CN007 AIN10 P15/A5 54 LCC-LT (+) UPWM8 P46/D6 STBY+5V LCC-LB (–) 1 8 + – 3 HFBP 14 71 P45/D5 TO D BOARD CN505 SDA1 4 149 IC003 EEP ROM AIN0 4 IC5101 (1/2) 153 VSOSD VDF Q010 + – LCC-LB (+) 157 75 89 12 CN011 D SCL1 152 CN010 16 6 SDA2 P82 HDF 2 IC5101 (2/2) [ AEP ] GS5001 GEOSENSOR SCL1 ABL SDA IC011 ROM 7 SCL2 AIN8 6 + – 3 UIN5 AIN7 7 4 UOUT1 HFBP + – IC5301 (1/2) 3 SOG DET 3 S4 5 CN5002 8 ECO SW 4 DDC SCL 1 SCL1 VS1 DDC+5V 1 S6 6 156 IC006 TO D BOARD CN504 7 [ U/C ] UPWM21 5 C VS1 8 + – 7 HSOUT TO A BOARD CN403 STBY+5V 8 SCL UIN3 UPWM17 B2 7 6 HD TO A BOARD CN403 6 VSP B1 DET2 31 CN001 [ AEP ] 107 5 VCLK 4 106 VC2 IC001 CPU/DSP VCC HOST GND 2 HS2 UBI4 VCC 1 UBI3 VS2 2 VS 2 49 SCL2 HS/CS 2 48 VCLK 5 SDA2 6 DDC SDA 2 SCL DDC SCL 2 IC5301 (2/2) DET1 SDA 7 SCL2 VS2 DDC+5V 2 SDA1 A TO CONNECTOR PANEL CN002 SDA2 DET2 [ U/C ] 5-4 I TO H1 BOARD CN801 G (POWER SUPPLY) CN654 4 IC650 +220V SHUNT REG S891 POWER T620 PIT TH601 CN891 CN603 1 AC L OUT AC L OUT 1 3 AC L IN AC L IN 3 5 D650 D610 RECT J (POWER SW) 1 3 RY602 3 T601 9 1 VCC CATHODE 4 H CENT L 4 +220V 5 +220V 6 +80V 4 –15V 1 +12V 2 +15V 2 3 5 4 +80V 6 +220V 8 D652 2 11 1 12 +12V 9 HEATER 1 SYBY+5V 2 1W+5V 2 1W+5V 1 STBY+5V 3 ECO SW 6 HTR SW 4 PWR SW 5 DGUS SW 6 CN652 T621 PRT 1 DGC 1 DGC 4 Q603 REG OUT START UP IN OUT 3 2 7 3 PROTECTOR POWER SW Q650-654, 667 E TO A BOARD CN405 5 VCC SW Q631-633 PH620 CN801 TO N BOARD CN007 1 6 4 REG SW Q621 RELAY DRV Q691 I IC654 +12V REG RY603 DGC F TO D BOARD CN501 PS650 2.0A L410 AFC CN601 G TO D BOARD CN508 GND 5 1 1 9 10 7 3 H CENT N 3 CN653 10 L SEN AC N 2 DRAIN 1 4 AC SEN F601 6.3A CN602 2 7 8 AC L H CENT H 6 3 AC INLET 1 1W+5V 6 1W+5V STBY+5V 7 STBY+5V LED0 1 LED1 2 KEY DET 3 ENV DRI 8 LED DRV Q801, 802 STBY+5V IC630 REG 8 LED DRV Q803, 804 7 R VCC SW Q610 6 2 1 8 1 G REG SW Q630 IN 4 OUT 2 4 VCC OUT CTL 3 2 MENU STBY+5V 4 VCC OUT CTL PH630 3 1 IC651 HEATER REG 5 S801 RESET 2 2 POWER S812 4 PROTECT Q670 IC652 STBY+5V REG 2 D801 1 IC653 1W+5V REG T630 SRT 3 3 VADJ 1 IC680 2 CN650 4 1 5 HEATER SW Q671 3 TH801 1 FUNCTION KEY H1 (USER CONTROL) B-SS3525 <U/C> -BD3-EPS05 5-5 5-6 H TO D BOARD CN502 5-2. FRAME SCHEMATIC DIAGRAM [ U/C ] CN402 6P WHT :S-MICRO 1 2 3 4 5 6 3 8 2 7 [ AEP ] 1 6 15 11 13 12 CN407 8P KB GND KG GND KR GND HEATER+ GND 9 14 VIDEO AMP, RGB OUT 5 4 9 15 A GND 2 IN 2 GND 2 IN 2 GND 2 IN 2 10 5 10 B B G G R R 14 4 HD15D-SUB 8 13 INPUT 3 INPUT CN408 8P 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 KB GND KG GND KR GND HEATER+ GND PICTURE TUBE H CN401 HD15D-SUB C BLOCK 7 G2 N.C G2 G2 GND KB KR G2 G4 KG G1 GM HV (CRT SOCKET)FV GND FC 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 CN403 21P L-FPC STBY+5V 1W+5V GND +80V N.C +220V N.C +12V HEATER 1 2 3 4 5 6 7 8 9 CN405 9P WHT-L :S-MICRO 11 1 CN406 2P WHT :VH 6 ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND NC SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 12 2 CONNECTOR PANEL RCV 1 CHASSIS GND (DEFLECTION) TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO_SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAPE CN509 10P :VH GND 1 V.DY C 2 V.DY H 3 NC 4 H.DY C 5 H.DY C 6 NC 7 NC 8 H.DY H 9 H.DY H 10 H.DY FASTEN V.DY CN503 4P WHT 1 2 3 4 5 6 7 8 CRT SHIELD CN801 11P WHT-L :S-MICRO 5-8 1 2 3 4 ECS STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND GND STBY+5V RXD TXD 1 2 3 4 5 6 7 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 H1(USER CONTROL) 5-7 HV N.C G2 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 CN508 8P WHT :S-MICRO LED0 LED1 KEY_DET NC GND 1W+5V STBY+5V ENV_DRI GND LED0 1 LED1 2 KEY_DET 3 NC 4 GND 5 1W+5V 6 STBY+5V 7 ENV_DRI 8 GND 9 GND 10 GND 11 1 2 3 4 5 6 7 8 9 CN007 9P WHT :S-MICRO CN5003 2P WHT :S-MICRO LCC-NS(+) LCC-NS(-) 1 2 LCC-NS LCC-RB LCC-RT(+) LCC-RT(-) LCC-RB(+) LCC-RB(-) LCC-RT LCC-LB LCC-LT(+) LCC-LT(-) LCC-LB(+) LCC-LB(-) CN5002 8P YEL :S-MICRO 1 2 3 4 5 6 7 8 LCC-LT ROTATION CN506 2P WHT :VH 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND NC SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 CN001 21P :FFC 8 7 6 5 4 3 2 1 GND DDC+5V 2 DDC SCL 2 DDC SDA 2 HOST GND 2 GND HS/CS2 VS2 V CONV(+) V CONV(-) H CONV(+) H CONV(-) ROTATION(+) ROTATION(-) AC L N.C AC N 1 2 3 4 5 6 1 2 3 1 2 3 4 5 6 7 H.CONV J(POWER SW) STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND V.CONV CN602 3P WHT :VH CN650 7P WHT :S-MICRO GND D CN502 7P WHT :S-MICRO AC L OUT N.C AC L IN CN603 3P 1 2 3 CN507 1P +12V +15V GND -15V GND +80V 1 2 3 CN891 3P WHT :VH AC L OUT N.C AC L IN 1 2 3 4 5 6 CN5001 6P WHT :S-MICRO POWER GND TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO_SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAPE FC FBT +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE CN505 25P :FFC CN011 25P FFC CN653 6P WHT :S-MICRO +12V +15V GND -15V GND +80V 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 CN604 1P 1 G POWER SUPPLY µ-COM, V.CONV,H.CONV,LCC, GEO MAGNETIC SENSOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 FV CN501 6P WHT :S-MICRO DGC N.C N.C DGC 1 2 3 4 5 6 7 8 CN504 25P :FFC H CENT H H CENT N H CENT L +220V +220V N.C GND GND STBY+5V 1W+5V GND +80V N.C +220V N.C +12V HEATER CN652 9P WHT :S-MICRO 1 2 3 4 N H CENT H H CENT N H CENT L +220V +220V N.C GND GND CN601 4P WHT :VH DGC CN654 8P WHT :S-MICRO CN010 25P FFC +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE 1 2 3 4 5 6 7 8 9 CN002 8P WHT :S-MICRO CONNECTOR PANEL GND B-SS3525<U/C>-KESSENZU-EPS05 5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 5-3. CIRCUIT BOARDS LOCATION Note: D • All capacitors are in µF unless otherwise noted. (pF: µµF) Capacitors without voltage indication are all 50 V. • Indication of resistance, which does not have one for rating electrical power, is as follows. A Pitch: 5 mm Rating electrical power 1/4 W (CHIP : 1/10 W) • All resistors are in ohms. • f : nonflammable resistor. • Ï : fusible resistor. f : internal component. • • p : panel designation, and adjustment for repair. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. e : earth-ground. • • E : earth-chassis. • The components identified by [ in this basic schematic diagram have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. • When replacing components identified by ] , make the necessary adjustments indicated. (See page 3-1) • When replacing the part in below table, be sure to perform the related adjustment. N G H1 J Note: The components identified by shading and mark ! are critical for safety. Replace only with part number specified. Terminal name of semiconductors in silk screen printed circuit ( ) Part Replaced ([) HV ADJ RV901 Device 1 HV Regulator Circuit Check Base HV Protector Circuit Check Beam Current Protector Circuit Check D Board C920, IC901, R923 R924, R929, R945, RV901, T902(FBT) • Mounted D Board • • • • 2 Transistor 3 Diode Emitter Collector Base Emitter Cathode Anode Cathode 4 D Board C922, C925, C926, D912, D914, D915, D921, Q907, Q908, R921, R922, R932, R937, R939, T902(FBT) • Mounted D Board Diode Anode (NC) Cathode 5 Diode Anode (NC) Common 6 7 Diode Anode Diode Cathode Common Anode Cathode Common D Board C910, C921, C933, D901, D902, D913, IC503, IC901, R901, R920, R928, R930, R931, R940, R941, T902(FBT) • Mounted D Board G Board IC652 • Mounted G Board N Board IC001, R031, R032 • Mounted N Board 8 Diode Anode Anode Common 9 Diode Anode Anode Common 0 Diode Cathode Cathode Common qa Diode qs Diode qd Transistor (FET) Cathode Anode Anode Cathode Drain Cathode Cathode Anode Anode Source Gate D D G Transistor (FET) qg Transistor (FET) Source Drain Gate Transistor Emitter Collector Base – All voltages are in V. Readings are taken with a 10 M digital multimeter. Readings are taken with a color-bar signal input. Voltage variations may be noted due to normal production tolerances. * : Can not be measured. Circled numbers are waveform references. s : B + bus. S : B – bus. Source Gate qf qh Drain One sheet of N board circuit diagram is divided into three sheets, each having the code N-a to N-c. For example, the destination ab1 on the code N-a sheet is connected to ab1 on the N-b sheet. a b 1 Ref. No. Circuit diagram division code 5-10 G S S D D G G S S Discrete semiconductot (Chip semiconductors that are not actually used are included.) • Divided circuit diagram 5-9 Circuit Terminal name Collector Transistor Part Replaced (]) Note: Les composants identifiés par un tramé et une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • • • • * Printed symbol Ver.1.6 (1) Schematic Diagram of A Board 9 D/A_4 NC D/A_5 VCC_5V GND D/A_3 2.9 CLP SDA 23 SOG_OUT G_E.P. VCC G_OUT 2.7 GND 65.5 79.0 B_OUT R_OUT B_E.P 2.7 B_IN 2.6 2.7 58.1 KB GND KG GND KR GND HEATER + GND KB GND KG GND KR GND HEATER + GND 1 2 3 4 5 6 7 8 FC GND SK401 FC 11 10 G2 9 8 7 SG201 SG101 SG402 C417 4700p 2kV B R418 220k 1/2W (G2) +B 1 3 4 5 6 7 8 IC406 H8D2972 CUT OFF AMP R117 1M :CHIP D106 HSU83TRF R111 470 :CHIP 10 11 12 13 14 15 16 17 (G2) C115 0.1 250V G2 R118 1M :CHIP C120 0.1 250V R_CUTOFF C220 0.1 250V 1.2 1.2 1.2 5.8 5.8 5.8 105 103 109 107 103 101 1.7 R426 220k :CHIP C320 0.1 250V R404 2.2k :CHIP R405 680 :CHIP 5V FB102 D105 HSS83TD D107 HSU83TRF Q401 12V 2SC2412K DRIFT CORRECT 0.5 C464 0.01 B:CHIP +80V R220 470k :CHIP C440 0.01 B:CHIP FB403 1.1µH C442 0.01 B:CHIP C434 R414 1000p 47k 500V :CHIP B C433 12V 1000p 500V B C435 C437 0.01 * B:CHIP C444 11.9 1000p 500V Q407 B DTA114TUA FB411 1.1µH FB405 1.1µH 5V-2 R321 R320 470k 470k :CHIP :CHIP C467 1 250V R120 470k :CHIP R409 2.2M :CHIP D405 1SS119 PS401 1A L405 22µH 4.3 FB404 1.1µH BCI VS AVDD Hfly OVDD AV FBLK 25 GCI HS 24 22 C415 0.22 16V B:CHIP BOUT I L404 100µH C423 47 25V 21 5V PWM4 PWM0 PWM3 PWM1 PWM2 18 XT0 16 15 3.5 R119 15k :CHIP 17 11 ROUT 12 0 XT1 R459 10M :RN 12V R128 4.7k :CHIP R209 13k :RN-CP D203 1PS181-115 2 3 C213 0.22 16V B:CHIP R228 4.7k :CHIP C208 0.1 R222 25V 22k B:CHIP :CHIP Q301 2SC2412K BUFFER R454 2.2M :CHIP G2 CONT R451 560K :CHIP 2.7 6 5 C457 0.01 B:CHIP 8 C456 * 2.7 R464 2.2k :CHIP IC405(1/2) R450 NJM2904M(TE2) 4.7k G2 CONT :CHIP R463 100k :CHIP C313 R309 0.22 13k 16V :RN-CP B:CHIP 5V R461 220k :CHIP 3.8 7 4 R230 470k :CHIP Q410 534 2SC5022-02 1 IC405(2/2) NJM2904M(TE2) G2 CONT R_BKG R219 15k :CHIP C308 0.1 R322 25V 4.3 22k B:CHIP :CHIP C314 0.1 25V B:CHIP R328 4.7k D303 :CHIP 1PS181-115 5V 4.9 R442 1k 12V :CHIP 4.3 R449 22k :CHIP 4.3 D403 MTZJ-T-77-39B 4.3 Q406 2SB709A G2 CONT R453 10k :CHIP A(VIDEO AMP,RGB OUT) R330 470k :CHIP B-SS3525<U/C>-A..-P1-EPS05 G_BKG R319 15k :CHIP B_BKG +5V +5V Schematic diagram 5-11 R457 10M :RN R460 10k :CHIP G2 R455 100k :CHIP 1 2 R458 2.2M 1W :RN 4.9 19 GOUT 13 10 14 R419 220 :CHIP R130 470k :CHIP 5V C214 0.1 25V B:CHIP C430 0.01 B:CHIP 20 9 DVSS 3 2 C441 0.01 B:CHIP 0 R417 1M 2.3 :CHIP 1 DVDD 10 S C432 0.22 16V B:CHIP X401 8MHz 4.3 B_IK 0 R412 220k :CHIP C450 0.47 B:CHIP G_IK 0 3.4 L403 100µH C446 47 25V C113 0.22 16V B:CHIP 4.9 4.3 0.7 C425 100p CH:CHIP C114 0.1 25V B:CHIP 2SC2412K BUFFER R_IK 23 C426 100p CH:CHIP R406 100k :CHIP C438 0.1 B:CHIP 0.3 Q402 2SJ360-TE12L VCC KICK R109 13k :RN-CP D103 1PS181-115 A board l 5-12 STBY +5V 1W+5V GND +80V NC +220V NC +12V HEATER TO G BOARD CN652 CN406 2P WHT :VH G2 CONT 2.6 4.9 5V Q201 26 3 4 SCL 5 0.5 5V 4.3 6 R438 4.7k :CHIP C427 22p CH:CHIP RCI SDA 7 4.9 8 5V R122 22k :CHIP 28 27 1 2 ADCREF AGND 4.9 0.1 25V B:CHIP 1 2 3 4 5 6 7 8 9 4.3 R161 470 :CHIP OSCREF FB406 1.1µH 1.5KV 5V C108 Q101 2SC2412K BUFFER R261 470 :CHIP FILTER CN405 9P WHT-L :S-MICRO FB402 1.1µH R439 470 :CHIP C431 1000p B:CHIP 9 8 +220V R490 4.7k :CHIP R361 470 :CHIP IC404 CXD9514M OSD IMR 104 D205 HSS83TD 11.8 R436 2.2k :CHIP 6 G1 KR KG 7 C436 0.22 16V B:CHIP R430 100 :CHIP C419 1000p 500V B 3 4 H1 4.7 5 H2 C424 1000p 500V B R218 1M :CHIP G1 G1 KB L402 22µH SG401 FV 13 1 5V R415 100k :CHIP C416 2.2 C215 0.1 250V FB202 R114 22 :CHIP 4.9 SCL D305 HSS83TD 1 2 3 4 5 6 7 8 TO D BOARD R315 47 1/2W SG301 :SURGE R215 47 1/2W :SURGE R115 47 1/2W :SURGE R217 1M :CHIP D206 HSU83TRF R137 470 D207 HSU83TRF 22 20 C410 0.01 B:CHIP C406 0.01 B:CHIP R138 47 :CHIP R110 100k :CHIP R491 4.7k :CHIP C315 0.1 250V D307 HSU83TRF B_CUTOFF 5V FB202 R214 22 :CHIP G_CUTOFF INPUT_SW B_DET_IN R314 22 :CHIP R210 100k :CHIP 2.7 +220V R317 1M :CHIP CN408 8P 522 82.6 35 34 32 31 ABL_IN FV :CHIP C463 0.01 B:CHIP (GND) CN407 8P D306 R311 R318 220 1M HSU83TRF :CHIP R113 47 :CHIP 29 28 GND1(B) R212 22 :CHIP R211 220 :CHIP R_OUT R_BASE G_OUT G_BASE B_OUT B_BASE 5V (GND) C109 12p CH:CHIP C458 0.1 :CHIP C462 0.1 C459 :CHIP 22 100V 2.7 12V R310 100k :CHIP R112 22 :CHIP +80V C209 10p CH:CHIP R238 R237 47 470 :CHIP C110 0.001 CH:CHIP 9 10 11 12 13 14 15 12V R407 470k:RN-CP R403 22k :CHIP 30 13 14 D/A_2 27 VCC2 C312 0.22 16V B:CHIP R402 1k :CHIP 25 G_DET_IN NC BLK R213 47 :CHIP R216 4.7k :CHIP R312 22 :CHIP 8 12V 2.8 24 3.4 V_DET D/A_1 7 R116 4.7k :CHIP 6 26 25 V_DET_C GND 15 GND OSD_B 16 R_DET_IN 23 2.7 4.3 6 R307 680 :CHIP C422 0.22 16V B:CHIP 0.7 17 VCC1 VCC2 0 C407 0.01 B:CHIP 18 G.DET 4.4 24 HOLD_CR2 GND 5 5 B_IK G_IK R_IK B_IN G_IN R_IN VBB GND VCC1(B)CONT_DAC B_OUT VBB 41 40 39 38 37 36 B-IN C420 0.22 16V B:CHIP 2.7 R202 100k :CHIP 21 9 10 11 12 13 14 R488 47k :CHIP 33 10 GND1(G) 11 G_BUF.IN 2.0 4.9 5V D402 1PS184-115 42 1 2 3 7 OSD_G Main_Brightness 4 C309 C421 10p 0.01 B:CHIP CH:CHIP C210 0.001 CH:CHIP 12V VCC1(G)CONT_REF 3 14 13 C BLOCK 3 2 C310 0.001 CH:CHIP 4.6 2.6 C413 * R411 4.7k 5V :CHIP R441 1M :CHIP GND 4 1 R316 4.7k :CHIP R207 680 :CHIP 12 +220V D406 1PS226-115 C449 1 B:CHIP R313 47 :CHIP 2 R221 470k :CHIP R121 470k :CHIP D407 1PS226-115 H NC 12 HOLD_CR1 SYNC_SEP.OUT 18 7 VDD A6 Y6 A5 Y5 A4 Y4 A1 Y1 A2 Y2 A3 Y3 GND R107 C443 680 0.01 B:CHIP :CHIP 8 1 2 3 4 5 G 1 R420 2 100 :CHIP R421 3 100 :CHIP 4 R422 5 100 :CHIP 6 R424 :CHIP 7 1k R428 :CHIP 8 100R427 1k :CHIP 9 10 R425 11 * 12 R443 100 :CHIP 13 R444 100 :CHIP 14 15 R445 * 16 R446 * 17 18 R447 * 19 R448 * 20 R456 * 21 SOG_IN 0.1 6 F ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND INPUT_SEL SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 TO N-a BOARD CN001 G_IN 8 30 27 B_IN1 28 G_BUF.OUT 26 GND C206 1 10V B:CHIP 5V E 4 6 31 C212 0.22 16V B:CHIP 0.6 CN403 21P L-FPC GND2 1 R337 470 2.6 G_OUT 0 GND 2.6 IC407 SN74HC04ANSR G SYNC BUFFER 0.5 NC 9 B_OUT 29 G_IN1 4.5 D GND1(R) R_OUT 19 C408 0.01 B:CHIP C405 0.1 25V B:CHIP OSD_R 5 36 35 33 32 34 1 2 4 5 6 8 9 7 5V-2 5V R431 470k :CHIP C207 0.1 25V B:CHIP 2.6 R413 C404 100k :CHIP 220p CH:CHIP 12 7 2 C112 0.22 16V B:CHIP C307 0.1 25V B:CHIP 0.6 C304 * 11 6 1 C216 0.01 B:CHIP 22 R303 * GND VCC2 21 INPUT (HD15) C403 220p CH:CHIP C204 C303 * * R_IN1 20 C D302 * B 2.7 VCC1(R) 0 VCC2 2.7 0 2.5 R306 * 13 8 3 GND 19 CN401 * VCC2 10 14 9 4 R_IN 2.4 D202 * R206 * R203 * VCC2 G_OUT OSD_BLK R338 47 :CHIP C411 * 2.6 D102 * G 5 B_IN2 C107 0.1 25V B:CHIP 2.6 C401 C402 10 47 25V 10 15 VCC2 GND 11 [ AEP ] D301 1PS226-115 C205 0.01 B:CHIP G_IN2 12 AEP: N.C U/C: TO CONNECTOR PANEL R_OUT 13 6 5 4 3 2 1 2 2 2 2 2 2 2.4 2.5 3 C102 C201 47 0.01 25V B:CHIP R205 47 :CHIP G R201 C202 75 47 C301 :RN 25V 0.01 B:CHIP R305 47 :CHIP B R301 C302 C103 75 * 47 :RN R106 25V * R R103 C104 C203 * * * VCC2 VCC2 14 B R R101 75 :RN R_IN2 15 R IN R GND G IN G GND B IN B GND D201 1PS226-115 +12V IC402 M52749FP-TP RGB DRIVE 5V 16 CN402 6P WHT :S-MICRO 5V D101 1PS226-115 C101 0.01 B:CHIP R105 47 :CHIP 17 A IC401 M52757FP-TP INPUT SELECT 11 IC403 FA4301 RGB AMP 12V 5V-2 10 95.6 8 R_E.P. 7 6 VBB R_IN 5 GND 4 VBB 3 G_IN 2 2.6 1 G2 G2(NC) TO D BOARD CN506 OUTPUT (R) GND2 (R) Vcc2 (G) OUTPUT (G) GND2 (G) Vcc2 (B) OUTPUT (B) GND2 (B) G Buffer out Sync SEP in Sync SEP out Vcc3 V-DET in3 GND4 V-DET in2 Vcc4 V-DET in1 IC401 M52757FP Vcc2 (R) • A BOARD 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 [ U/C ] CONNECTOR PANEL RCV TO A BOARD CN402 G V901 PICTURE TUBE 21TKC H R G Sync Sepa B OR KB KR G2 G4 KG G1 GM HV 5 10 4 9 3 8 2 7 1 6 11 15 14 13 TO D BOARD T902(FBT)HV 12 HD15D-SUB 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Input1 (B) Vcc1 (B) Input2 (R) GND1 Input2 (G) GND5 Input2 (B) Sync DET1 Sync DET2 S-DET out Vcc5 Video DET-Hold 17 18 SWITCH 2 Vcc1 (G) Input1 (R) 1 Input1 (G) TO N BOARD CN002 Vcc1 (R) B-SS3525<U/C>-A..-P2 V-DET out G DET INPUT • A BOARD WAVEFORMS [U/C] – – – – – – 47/ 25V 100/ :CHIP 220/ 16V – CN401 HD15D–SUB – D102 D202 D302 1PS226–115 1PS226–115 1PS226–115 – – – R103 R106 R203 R206 R303 R306 R425 R445 R446 R447 R448 R456 75/ :RN 47/ :CHIP 75/ :RN 47/ :CHIP 75/ :RN 47/ :CHIP 1K/ :CHIP 100/ :CHIP 100/ :CHIP 47/ :CHIP 47/ :CHIP 100/ :CHIP – – – – – – – – – – – – 2 1 4.7 Vp-p (H) 4 66.0 Vp-p (H) 5 64.0 Vp-p (H) 7 65.0 Vp-p (H) 0 • A BOARD 3 IC402 M52749FP 4.8 Vp-p (H) 6 4.6 Vp-p (H) 8 64.0 Vp-p (H) OSD IN (R) 4 INPUT (R) 2 VCC1 (R) 3 GND1 (R) 5 OSD IN (G) 9 INPUT (G) 6 VCC1 (G) 8 64.0 Vp-p (H) 9 64.0 Vp-p (H) CLAMP SUB CONTRAST MAIN CONTRAST Retrace BLK IN [AEP] 0.01/ B:CHIP 47/ 25V 0.01/ B:CHIP 47/ 25V 0.01/ B:CHIP 47/ 25V 220/ 16V 0.01/ B:CHIP 470/ :16V 0.22/ 16V/ B:CHIP Main Brightness Ref. No. C103 C104 C203 C204 C303 C304 C411 C413 C437 C456 VCC2 • A BOARD * MARK LIST 42 34 30 OSD MIX AMP RETRACE BLANKING 41 RETRACE BLANKING 38 OUTPUT (G) RETRACE BLANKING 33 OUTPUT (B) OUTPUT (R) CLAMP F/B CLAMP SUB CONTRAST MAIN CONTRAST OSD MIX AMP CLAMP F/B GND1 (G) 10 OSD IN (B) 13 2.2 Vp-p (8MHz) INPUT (B) 11 CLAMP SUB CONTRAST MAIN CONTRAST OSD MIX AMP VCC1 (B) 12 35 Contrast ref. CLAMP F/B GND1 (B) 16 INPUT (SOG) 7 31 Contrast cont. OSD LEVEL 4bit Main CONTRAST 8bit ABL IN 17 19 VCC=5V Sync On Green Sep B SUB CONT 8bit G SUB CONT 8bit R SUB CONT 8bit SOG Sep OUT 20 23 SDA BUS I/F DAC 22 SCL 5-13 32 36 39 GND GND GND2 D/A OUT1 D/A OUT2 D/A OUT5 5-14 D/A OUT3 25 26 27 28 29 D/A OUT4 1 OSD BLK IN GND – : Not used 14 Clamp Pulse IN 24 GND (5V) 21 A — A BOARD (Conductor Side) — 1 2 3 VIDEO AMP RGB OUT • A BOARD SEMICONDUCTOR LOCATION — A BOARD (Component Side) — 1 2 IC Component ( Conductor Side ) ( Side ) IC401 IC402 IC403 IC404 IC405 IC406 IC407 A A-2 A-3 B-3 B-2 A-2 C-3 D-2 A-1 D-2 A TRANSISTOR Component ( Conductor Side ) ( Side ) Q101 Q201 Q301 Q401 Q402 Q406 Q407 Q410 * C-1 C-1 C-1 A-3 D-3 D-3 D-3 D-2 D-1 1 1 1 1 qg 1 2 – DIODE B Component ( Conductor Side ) ( Side ) D101 D102 D103 D105 D106 D107 D201 D202 D203 D205 D206 D207 D301 D302 D303 D305 D306 D307 D402 D403 D405 D406 D407 C * 6 B-1 B-3 A-3 A-1 B-1 A-2 A-2 B-1 B-3 A-3 A-1 A-1 A-1 A-2 B-1 A-1 A-3 A-1 A-1 A-1 A-3 A-2 D-3 D-2 D-2 D-3 A-2 D-1 7 qa – 3 3 6 7 qa – 3 3 6 6 qa – 3 3 9 – – 6 6 B C CRYSTAL Component ( Conductor Side ) ( Side ) X401 C-2 C-2 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) D D NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. Schematic diagram Ò A board 5-15 5-16 3 H1 (2) Schematic Diagrams of H1, J Boards 1 2 3 4 5 6 7 USER CONTROL 8 9 J 10 POWER SW 11 12 A Q803 2SA1309A LED DRIVE C802 47 16V 4.9 Q804 2SA1309A LED DRIVE R824 0.2 R823 1k :RN CN891 3P WHT :VH R813 22k 4.9 2.2 B — J BOARD — 1W+5V Q801 2SC3311A 1.5k LED DRIVE :RN STBY+5V CN801 11P WHT-L :S-MICRO R811 10k 4.4 0 1 2 3 4 5 6 7 8 9 10 11 R812 10k 3.7 0.1 R822 470 :RN G Q802 2SC3311A LED DRIVE R R821 150 :RN D801 SPR-325MVW POWER C R804 220 R803 220 R802 470 S891 POWER AC L OUT 1 NC 2 AC L IN 3 R801 1k TH801 10K LED0 LED1 KEY_DET NC GND 1W+5V STBY+5V ENV_DRI GND GND GND TO G BOARD CN603 J (POWER SW) TO N-a BOARD CN007 B-SS9116<NH.>-J.. TO CRT SHIELD R814 100k S801 MENU D R853 100 R852 100 R815 10k :RN C806 47 16V R851 470 S812 G RESET E H1(USER CONTROL) B-SS3525<U/C>-H1.-EPS05 F — H1 BOARD — G H I J 5-17 5-18 13 14 (3) Schematic Diagram of D Board 5 7 6 8 H I R932 1k :CHIP C925 47 -15V R933 C922 0.1 33k :RN-CP 100V :PT C701 22 100V R719 3.3k :RN-CP C706 0.1 25V B:CHIP C712 0.22 100V :PT R727 1 :FPRD 2 OUT D710 HZS5.1NB2 R716 39k :CHIP 1.7 R720 R721 10k 10k :CHIP :CHIP D706 EGP10PKG23 Q707 R713 2SC4634LS-CB11 V DRIVE 2.7k Q706 2SA1037AK V DRIVE :CHIP 4 + 6 Vcc D510 HZS5.1NB2TD +VIN -VIN VEE OUT VCC D515 HZS5.6NB2TD C710 220 35V :HT ABL C567 R559 2200p 10k R941 B:CHIP :CHIP 100 :CHIP 5.0 0 0 7 6 5 4 3 2 5 R582 100 1/2W :RN IC503 BA10324AF AMP 1.8 1.8 1.1 R1505 4.7k :RN-CP R725 1.8 1/2W :RN 4.8 S 0 4.8 S R522 R514 C519 R537 C517 R530 100k C505 47k 0.01 47k 0.01 1k :CHIP 0.01 B:CHIP :CHIP R531 B:CHIP B:CHIP 100k R1506 R513 R526 R524 :CHIP 1k 1k 100k 1k :CHIP :CHIP :CHIP :CHIP R504 1k :CHIP 4.8 S 1.1 3 0 C557 R538 C526 R542 47k 0.01 1k 0.01 B:CHIP:CHIP R539 B:CHIP 100k R1507 :CHIP 100k :CHIP 0 Q513 2SK3262 S-CAP CHANGE S 0 1 R501 47 2W :RS 0.01 :PT C531 0.1 250V :PP R587 100 2W :RS T505 HLC RY501 R584 47k R512 22k :RN S 1 D517 ERA91-02TP1 4 Q512 2SK3262 S-CAP CHANGE R726 1.8 1/2W :RN Schematic diagram Ò H1 J boards D board l 4 2 Q518 2SD2394-EF HL OUT Q516 0.5 2SB1565EF HL OUT Q523 2SC2412K C566 C528 0.22 250V :CQ T503 HST 1 2 3 4 5 6 7 8 9 10 3 C572 0.001 B:CHIP R1510 10k :CHIP R591 100 2 R594 C538 R567 R580 100 100 22k 0.01 :RN-CP B:CHIP 1/2W 1/2W :RN :RN R598 10k :RN-CP C565 R599 0.1 1.8k R503 25V 1k B:CHIP :RN-CP:CHIP 9 10 11 12 13 14 0 0 8 3 4 5 R940 10k :CHIP 1 O2 -2 +2 VCC +1 -1 O1 2.5 Q524 2SA1037AK PIN AMP D512 4.4 1SS355TE-17 +15V 4.8 S 0 R505 1k :CHIP R515 1k :CHIP TH501 TH502 1.2 R728 220 1W :RS D708 GP08DPKG23 D707 HZS5.1NB2TD CN509 10P :VH VV+ 7.7 C568 C577 0.047 B:CHIP R510 10 C536 47 10k :RN-CP C562 0.01 B:CHIP R595 2.2k :CHIP C537 C544 0.056 400V Q517 0.027 :PP 2SK3262 400V R583 47k C550 0.15 400V S-CAP CHANGE S 0 D516 1SS133T-77 L503 1mH R577 33 1/2W :FPRD S R551 R563 1k 1k :CHIP :CHIP R552 C535 R558 R565 C542 R573 R545 C530 R548 100k 100k 0.01 47k 0.01 47k 100k 0.01 47k :CHIPB:CHIP :CHIP B:CHIP :CHIPB:CHIP V- C711 6800p B:CHIP C707 C709 R724 0.01 2.2k 0.1 B:CHIP :RN-CP :PT HCENT HSPBAL ABL_DET C545 22p 500V CH C555 2.2 250V C556 1.2 250V :PP L504 4.7mH R581 100 R588 68 1/2W 1/2W :FPRD C559 14.7 2.2 0 250V R585 10k :CHIP V+ UP OUT 7 5 Schematic diagrams 5-19 C512 220p CH:CHIP D522 D504 1SS355TE-17 1SS355TE-17 S C560 0.01 B:CHIP Q519 DTC114GKA RELAY DRIVE D(DEFLECTION) 0.6 1.1 1.1 R711 C720 R717 10k 1k 10 :CHIP :CHIP R536 C504 22k 4700p :RN-CP B:CHIP C561 47 25V 7.7 R543 R517 C525 R1518 12k 33k 100 0.047 :CHIP :RN-CP :RN-CP B:CHIP R541 R518 R1503 R1504 C575 3.9k 0 47k 20k R597 0.01 :RN-CP :RN-CP :RN-CP CH:CHIP 10k :CHIP :CHIP C527 0.01 B:CHIP R521 C508 4.7k 22 :RN-CP 0 13.9 1.8 -13.4 400V R732 470k 198.1 1/2W :SURGE C704 470p 2kV B R511 4.7k :CHIP R507 C501 100k 0.01 :CHIP B:CHIP OUT VEE Vcc 1 3 1.1 VSHAPE R729 1 1/2W :FPRD C713 1000 25V IC701 LA7841L V DY OUT PUMP R710 10k :CHIP C574 4700p B:CHIP C564 C551 1 4700p B:CHIP D923 1SS355TE-17 R575 7.5k :RN-CP C521 C509 Q501 Q511 Q510 Q506 Q525 0.39 2SK3262 0.82 Q507 2SK3262 2SK3262 2SK3262 2SK3262 2SK3262 250V S-CAP S-CAP CHANGE 250V S-CAP S-CAP CHANGE :PP S-CAP S-CAP CHANGE :PP CHANGE CHANGE CHANGE 28.5 -0.1 1.8 R723 3.3k :RN-CP R709 1k :CHIP R528 1SS355TE-17 12k :RN-CP R519 22k :CHIP HVDET HLIN R722 1 1/2W :FPRD C708 1000 25V HFBP VRET D520 C933 1 R718 18k :RN-CP R714 2.2k :CHIP R570 2.2k 1/2W :FPRD -15V -15V +15V C529 100 25V ABL R934 C903 10 4.7k :RN-CP DGUS HD 1 2 3 4 5 6 7 8 9 D519 1SS355TE-17 C921 0.22 100V :PT R571 4.7k R527 R556 8.2k 22k :RN-CP :RN-CP Q526 DTA143TKA GAIN SW R593 10k :CHIP 18 17 16 15 14 13 12 11 10 IC501 BA9759F PIN CONTROL R928 R930 5.1k 1.2k :RN-CP :RN-CP 7 +15V R576 1k 1W :RS 15V R701 2SC2362KG 1k H DRIVE :CHIP R731 R704 1.8 2.7k 1.5k :CHIP :RN-CP HTR C563 1500p B:CHIP C548 470p 2kV B S5 Q703 2SA1049 H DRIVE R578 1k :CHIP D513 1SS133T-77 27.4 R708 15 2W :RS 28.9 10 D514 1SS133T-77 R579 1k :CHIP R586 22k :RN-CP 0.7 28.1 Q705 2SA1358 H DRIVE 5 C554 100p 2kV :HR 0.1 Q520 2SC2412K BUFF 4 C546 100p 2kV :HR C547 1500p 630V :PP D511 FMQ-G5GS 2 8 2 1 T502 HCT R1517 47k :CHIP S6 R707 4.7 :FPRD C511 68p CH:CHIP C524 470p CH:CHIP C515 0.01 B:CHIP 1.2k D910 :RN-CP 1SS133T-77 R922 4.7 :FPRD 12 11 10 9 2 3 4 5 Q701 ECO C516 470 16V D913 1SS133T-77 R534 39k :RN-CP R920 47k :CHIP D912 EGP10GPKG 2 C571 10p CH:CHIP C543 3600p 1.8kV R546 0.22 3W :RS 3 R533 1 1/2W :FUSE C520 1000 25V 8 6 6 29.6 29.5 2.5 R921 10k 1 R535 4.7k :CHIP R931 D914 1SS133T-77 T701 DFT 12 D915 0 HZS33NB2TD Q908 DTC114GKA HV DET C926 10 11 R529 2.2k R523 0.47 220 :CHIP Q503 :MPS :CHIP C518 2SA1036K 0.47 H DRIVE :MPS 1 5 4 R566 R569 R564 33k C541 47k 12k 2200p :RN-CP :RN-CP :RN-CP B:CHIP R557 27 1W :RS 28.4 14.7 9 10 C506 4.3 :PT R532 33 1W :RS O3 -3 +3 VEE +4 -4 O4 R937 4.7k :CHIP +12V R706 4.7 :FPRD 29.3 R590 2.2k :CHIP R502 2.7k :CHIP C924 R935 0.1 47k 100V :CHIP :PT 16 7 3 5 82.5 75.5 R715 4.7 :FPRD Q515 2SC5570 H OUT 528 -0.9 D508 D5SC4M T501 HDT C703 2200p 1kV :E R572 0.47 C549 0.1 3W :PT C532 R555 R562 10k 12k 0.001 B:CHIP :RN-CP :RN-CP R544 1k :CHIP C702 47 100V Q704 2SC3421 H DRIVE R705 470 :FPRD R924 10k :CHIP Q509 2SC3746 C522 H OUT 4700p :PT D5061.8 C523 1SS133T-77 4700p -14.4 4.3 4 FC FC TO A BOARD 18 1 Q514 2SC3209LK H CENT 4.5 S0 HDF C916 2000p 1.2kV :PP 8 14.7 FB507 1.1µH S1 D703 1SS133T-77 C715 0.1 25V B:CHIP S 3 C540 0.001 200V :PT 5.0 D509 1SS133T-77 S5-1 Q702 2SC2459 H DRIVE D701 1SS133T-77 S1 D907 HZS16NB2TD R939 1k :CHIP R703 39k :RN R730 10k :CHIP Q906 2SK2655 HV OUT 5 C918 4700p 100V :PT C917 0.33 250V :PP Q907 DTA114GKA HV DET 31.4 R509 1k :CHIP C513 4700p B:CHIP 9.4 C558 100 25V R702 10 :FPRD S2 6 Q904 2SA1036K HV DRIVE +80V S5-1 2 2 R916 22 :FPRD 8.2 D921 1SS355TE-17 R925 330k 1/2W :RC C923 SG901 3300p FV TO 200V FV A BOARD :PT SG903 R927 14 1k 1/2W :RC R926 15 1k 1/2W SG902 :RC R918 68 :10W 192 8.3 S4 S3 S5 RV901 100k HD D909 C920 0.022HZS16NB2TD :PT C539 4700p B:CHIP C534 220 R561 25V 8.2k :HT :RN D709 ERA22-06AVRBT 4 ≠≠ S5 ≠ TO N-a BOARD CN011 1 8.9 VDF G 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R923 270k :RN-CP C507 0.22 :MPS 9.0 R912 1k :CHIP D702 1SS133T-77 R929 10k :RN-CP R919 4.7k 1/2W :RC L902 15µH 6 D906 YG911S3R Q903 2SC2411K C915 HV DRIVE 0.22 :MPS C914 C912 0.047 0.047 200V 200V :PT :PT 29.9 TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAP 8 D904 1SS355TE-17 THDET HV 17 217 R911 470 :CHIP 6 -7.6 1 9 13 R914 22 CN505 25P :FFC TO PICTURE TUBE HV 10 5 25 24 23 22 21 TXD 20 19 RXD 18 17 16 15 HDF 14 13 VDF 12 11 10 ABL_DET 9 HVDET 8 S0 7 HCENT 6 S6 5 4 HSPBAL HLIN 3 HSIZE 2 HSP 1 5 R547 2.2 10W :RN S3 F HV ADJ T902 :FBT FB901 1.1µH R915 4.7k :CHIP D507 YG911S3R +12V Q502 R508 2SC2412K 220 H DRIVE VCC TO N-a BOARD CN010 +220V R550 0.47 1/2W :FPRD 4 R1515 47 3W :RS HSP HSIZE D923 1SS355TE-17 VSHAPE VRET E Q505 2SA1036K PIN DRIVE +15V S4 C913 33 400V CN504 25P :FFC +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE +15V D919 1SS133T-77 15 400V 82.0 2 R554 15k :RN-CP R904 R906 220 220 :CHIP :CHIP Q905 T901 2SJ569LS HRC D905 HV REG SW 1 147 HZS13NB2TD R908 6.8 3W L901 :RS 100µH HCENT L 82.5 R568 3.9k :CHIP 78.4 R540 47 3W :RS 200V :PT 200V :PT D902 HZS12NB2TD 9 L502 2.2mH FB502 1.1µH D505 HZS13NB2TD C514 C573 9.0 R520 0.022 0.022 22 2 D R1501 1k :CHIP +B RXD TXD C502 0.22 :MPS 3.1 D920 C931 10 R907 22k :CHIP 2 9.1 HZS4.7NB2TD 161 G ≠≠ S5 ≠ 9 10 10 HCENT N D R525 4.7k :CHIP C533 220 25V :HT 218 C908 0.01 B:CHIP 0 1 3.3 8 Q508 2SJ569LS PIN OUT S Q504 2SC2411K PIN DRIVE R1502 220 :CHIP C927 47p CH:CHIP FB501 1.1µH S2 7 C510 33 250V L501 100µH 9.0 9.0 6 14 13 R574 C552 IC502 LA6500-FA 100k 0.01 H CENT OUT :CHIP B:CHIP R560 10k :RN-CP R553 220 +90V L505 HOC C930 10p CH:CHIP R902 680k :RN-CP R549 0.47 1/2W HCENT H :FPRD 2.0 5 C905 270p CH:CHIP C902 100 25V 4 D918 1SS133T-77 1 2 3 4 180p CH:CHIP C928 470p CH:CHIP 2.5 3 9.3 9.1 C901 0.01 B:CHIP DGUS HTR 2 C919 4700p 2kV :E S TO ECS 1 D917 +15V 1SS355TE-17 ECO CN503 4P WHT GND STBY+5V RXD TXD R943 4.7k :CHIP R917 220 1/2W :FUSE R945 100 :CHIP - C TO G BOARD CN650 C935 1000p CH:CHIP 9.0 IC901 BA9758FS HV CONTROL 1 2 3 4 5 6 7 D908 ERA34-10TP1 20 19 18 17 16 15 14 13 12 11 CN502 7P WHT :S-MICRO STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND 2.5 FB504 1.1µH R903 47k :CHIP C910 C932 3.3 0.01 B:CHIP C929 0.1 25V B:CHIP 9.0 TO G BOARD CN653 FB503 FB506 FB505 1.1µH 1.1µH 1.1µH 1 2 3 4 5 6 D922 ERA34-10TP1 D901 1SS133T-77 SVcc VREG9 PVcc NC AGC PWMOUT PGND SAWOUT HVD NC HVDCAP SGND 3.2 NC HDIN SLOW SW3.5 DELAY NC 8.9 + ERROUT B +12V +15V GND -15V GND +80V C909 470 16V 2.0 C907 CN501 6P WHT :S-MICRO 12 CN508 8P WHT :S-MICRO 2.5 R901 100k :CHIP 11 8 7 6 5 4 HCENT L 3 HCENT N 2 HCENT H 1 CN506 2P WHT :VH 1 2 G2 G2(NC) A 10 TO G BOARD CN654 GND GND NC +220V +220V H CENT L H CENT N H CENT H TO A BOARD CN406 9 HFBP 4 SAWR PWMOUT3.6 SAWOUT PGND SGND SLOW SW 6.8 HDIN ERRIN NC 2.5 REFIN MIX+ NC 2.5 MIXERROUT MIXOUT 3 PVCC 2 VREG9 1 Q521 Q522 2SC2412K 2SC2412K TH DET TH DET R516 1k R506 1k :CHIP B-SS9194<U/C>-D..-EPS05 :CHIP THDET R589 2.2k :CHIP C503 0.01 B:CHIP 5-20 GND V.DY V.DY NC H.DY H.DY NC NC H.DY H.DY C H C C H.DY FASTEN H H V.DY D • D BOARD WAVEFORMS — D BOARD — 2 1 8.8 Vp-p (H) 50.6 Vp-p (H) 1 3 2 3 4 568 Vp-p (H) 1.9 Vp-p (H) 5 4 DEFLECTION 6 54.5 Vp-p (H) A 2.1 Vp-p (H) • D BOARD SEMICONDUCTOR LOCATION IC IC501 IC502 IC503 IC701 IC901 DIODE C-4 A-1 C-4 A-5 C-1 TRANSISTOR Q501 Q502 Q503 Q504 Q505 Q506 Q507 Q508 Q509 Q510 Q511 Q512 Q513 Q514 Q515 Q516 Q517 Q518 Q519 Q520 Q521 Q522 Q523 Q524 Q525 Q526 Q701 Q702 Q703 Q704 Q705 Q706 Q707 Q903 Q904 Q905 Q906 Q907 Q908 B-5 A-4 A-4 C-4 D-4 B-5 C-5 A-2 A-4 C-5 C-5 C-5 C-5 B-2 A-3 B-4 D-5 B-4 D-4 B-5 B-5 C-5 D-4 B-3 C-5 C-4 D-4 D-3 D-4 D-3 D-4 D-3 D-3 B-3 C-3 C-3 C-3 B-2 B-2 * – 1 1 1 1 – – – – – – – – – – – – – 1 1 1 1 1 1 – 1 – – – – – 1 – 1 1 – – 1 1 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D515 D516 D517 D519 D520 D522 D701 D702 D703 D706 D707 D708 D709 D710 D901 D902 D904 D905 D906 D907 D908 D909 D910 D912 D913 D914 D915 D917 D918 D919 D920 D921 D922 D923 D-4 A-1 A-4 A-2 A-3 B-2 A-1 A-2 B-3 B-2 B-3 B-2 B-4 B-3 C-4 D-4 C-4 D-4 D-4 D-4 D-2 A-5 A-5 B-2 D-3 B-1 B-2 B-3 C-3 C-3 B-3 C-3 C-1 C-2 C-2 B-1 C-2 C-2 B-2 B-1 B-1 B-1 B-2 C-3 C-4 * 3 – – – – – – – 3 – – – – – 3 3 3 – – – – – – – – – – 3 – – – – – – – – – – 3 – – – 3 – 3 B C D VARIABLE RESISTOR RV901 B-1 NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) 5-21 5-22 5 • Divided circuit diagram 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 R081 1k :CHIP R021 100 :CHIP R020 100 :CHIP R019 100 :CHIP CBLK CLP R048 1k :CHIP R1007 1k :CHIP D036 HZS5.6NB2TD ABLDET VDF RXD TXD INPUTSEL SCL SDA SOG SOGDET HSOUT1 VSOSD R1006 1k :CHIP R025 100 :CHIP R022 100 :CHIP R026 100 :CHIP R006 * R005 * R015 * R016 * R018 * R017 * R039 100 :CHIP R040 100 :CHIP R032 3.9k D040 HZS5.6NB2TD R031 5.6k :RN-CP R030 1k PWR_SW DGS PRT_DET ECO_SW S1 THDET S4 S3 S5 S2 :CHIP :RN-CP HVDET R1029 100 :CHIP S0 HCENT R1025 100 :CHIP S6 HSHPBAL R1040 100 :CHIP HLINBAL HSIZE HSP R034 1k :CHIP R1034 100 :CHIP R1032 100 :CHIP R1033 100 :CHIP R1031 100 :CHIP R1030 100 :CHIP R1035 100 :CHIP R1037 100 :CHIP VRET R1038 100 :CHIP HTR R024 100 :CHIP R1039 100 :CHIP R1041 100 :CHIP L003 1000µH R1043 100 :CHIP D026 1PS226-115 ENV KEYDET INPUT_SW LED1 D018 HZS5.6NB2TD D025 1PS226-115 LED0 R1042 100 :CHIP R082 1k :CHIP R085 1k :CHIP R047 1k :CHIP FB002 FB001 1.1µH 1.1µH R086 1k :CHIP FB003 1.1µH C091 100 16V L002 100µH -15V +15V R050 * D014 * 5 R052 * 7 8 6 9 6 7 30 7 31 6 28 9 R011 4.7 :FPRD R012 * R013 * 26 12 25 13 24 R014 * 6 5 R1058 10k :CHIP R1059 1k :CHIP R1054 10k :CHIP R1056 10k :CHIP R004 R003 100 100 :CHIP :CHIP 7 R055 * R046 * R054 15k :CHIP 8 4 IC011 * 3 21 16 22 15 23 14 19 18 20 17 C069 0.1 B:CHIP D005 D006 D007 D011 D012 D010 D009 D008 R1057 1k :CHIP R1052 10k :CHIP R1053 1k :CHIP R1055 1k :CHIP * * * * * * * * HOST G 1 HOST G 2 HC1 HS/CS1 HC2 HS/CS2 VC1 VS1 VS2 VC2 DSCL2 VC2 DSDA2 DSDA1 DSCL1 D020 1SS355TE-17 ECO SOGDET ECO_SW HDSW VCC+4.5V HC1 VC1 HC2 OFFDET Q004 DTA124EUA ACTIVE OFF DET C082 47 25V R1070 C085 2.2k 0.01 :CHIP B:CHIP R045 1k Q011 2SA1037AK :CHIP HD SW -15V +15V ac1 ab7 ab6 ab5 ab4 N-a board l D001 1PS226 D002 1PS226 D003 * D004 * C012 * D015 * C011 * 2 R1063 4.7k :CHIP 1 R1049 10k :CHIP C087 10 D022 1PS184-115 C084 10 Q006 DTC123EKA ACTIVE OFF DET D038 UDZ-TE-17-2.2B Q007 R1045 4.7k Q005 DTC124EKA ECO SW DTA114GKA :CHIP ACTIVE OFF DET R1051 100k :CHIP 11 27 10 R044 1.8k :RN-CP R075 270 :RN R076 270 :RN C064 R1047 C1005 3300p 10k C065 25V :CHIP 470p B:CHIP Q003 Q001 CH:CHIP 1 Q002 2SA1037AK 2SA1037AK 2SA1037AK R060 C068 2.2k CURRENT CURRENT CURRENT 0.22 :CHIP MILLER MILLER MILLER :MPS R1027 R1026 R063 R064 R062 2.2k 330k R058:CHIP 27 27 27 :CHIP 5.6k :RN-CP :RN-CP :RN-CP :CHIP C063 C070 C066 R1028 2200p C071 1000 2200p 680 CH:CHIP680p 16V CH:CHIP :RN-CP B:CHIP D024 * D021 1SS355TE-17 D023 1PS184-115 R053 * R1050 10k :CHIP 29 8 R1022 2.2k :RN-CP R1023 2.2k :RN-CP ab3 Schematic diagram R007 2.2k :CHIP R008 2.2k :CHIP C001 0.001 B:CHIP R009 2.2k :CHIP R010 2.2k :CHIP C002 0.001 B:CHIP R051 * 5 9 IC012 * 6 C010 * 7 C009 * 8 8 4 11 3 12 2 13 4 5 R059 2.2k :CHIP C099 0.1 25V B:CHIP 1 10 14 5 IC005 SC74AHCT74PWR ECO DET 4 10 3 11 2 12 1 13 3 IC004 * 2 32 C094 0.1 C067 25V 0.1 B:CHIP 25V B:CHIP 1 14 C083 0.01 B:CHIP C089 0.01 B:CHIP 33 4 34 3 35 2 36 1 C078 0.22 :MPS C079 C080 0.01 47 B:CHIP IC010 LA7865M-TLM H.V.OSC,AFC, H.DRV,V.SHAPE • N BOARD * MARK LIST ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND NC SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO_SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAPE 1 2 3 4 5 6 7 8 9 SDA 5-24 5-23 SCL VSS C072 C073 0.1 1000 25V B:CHIP ab2 ab1 -a N (H.OSC,V.OSC,AFC,H.DRV,V.SHAPE) I B-SS3525<U/C>-N..-P1-EPS05 AEP:N.C U/C:TO CONNECTOR PANEL NC NC GND HS VCC NC 2Q 1Q 2Q GND GND VCC12 VCLK NC HSOUT VSHAPE Ref. No. C009 C010 C011 C012 LED0 LED1 KEY DET NC GND 1W+5V STBY+5V ENV_DRI GND HSDLY C074 C075 680p 100p CH:CHIP CH:CHIP R1024 18k :RN-CP C077 0.1 B:CHIP +12V STBY+5V H D016 HZS5.6NB2TD D017 HZS5.6NB2TD STBY+5V VSOSD G VSHP_C NC NC SDA VDC 1Q HPHASE 2PR 1Q VSAWRST 2Q 2CK 1Q 2PR 1PR 2CK 1PR DVSHAPE VDC VCC4.5 NC REG9V VCC12 SCL VSS AFC_SW GND HD NC FBP FILTER HD_DUTY F VCLK – : Not used VCC NC 2D 1CK NC DVSHAPE 1D VSHPLVL VSHPLVL S/HC 2Q NC 2CLR 2D 1CK 2CLR 1D VCC 1CLR VCC 1CLR NC 1W+5V GND DDC+5V 2 DDC SCL 2 DDC SDA 2 HOST GND 2 GND HS/CS2 VS2 MOIRE – – 4.7/ :FPRD 47/ :CHIP 47/ :CHIP – – – – – 47K/ :CHIP 15K/ :CHIP 15K/ :CHIP 1K/ :CHIP SUB+5V 8 7 6 5 4 3 2 1 VCO_C 100/ :CHIP 100/ :CHIP – – – 4.7/ :FPRD 47/ :CHIP 47/ :CHIP 1K/ :CHIP 10K/ :CHIP 0/ :CHIP 1K/ :CHIP 1K/ :CHIP 15K/ :CHIP 1W+5V CN002 8P :S-MICRO AFC_FIL R005 R006 R011 R012 R013 R015 R016 R017 R018 R046 R050 R051 R052 R055 HFBP HPLL – – 24LC21AT/SN E NC HPLL SN74AHCT74PWR 24LC21AT/SN – VSH HFREQ IC004 IC011 IC012 VSH FBP_DLY1 IREF_R – – HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD – – – HZS5.6NB2TD – 1PS184-115 – – VSAWRST FBP_DLY 1PS226 1PS226 – – – HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD – HZS5.6NB2TD – 1PS184-115 1PS184-115 D HFREQ D003 D004 D005 D006 D007 D008 D009 D010 D011 D012 D014 D015 D024 C HPHASE AFCSW [U/C] 0.1/ B:CHIP 47 – – R1061 10k :CHIP [AEP] – – 0.1/ B:CHIP 47 B Circuit diagram division cod CN001 21P :FFC A Ref. No. ab1 on the code N-a sheet is connected to ab1 on the N-b sheet. 14 13 12 11 10 9 8 7 CN010 25P FFC CN007 9P WHT :S-MICRO TO A BOARD CN403 TO D BOARD CN504 CN011 25P FFC TO D BOARD CN505 TO H1 BOARD CN801 6 5 4 3 2 1 each having the code N-a to N-c. For example, the destination (4) Schematic Diagrams of N (a, b, c) Board a b 1 One sheet of N board circuit diagram is divided into three sheets, ab7 ab6 +15V C096 0.01 B:CHIP C008 0.1 25V B:CHIP R1067 2.2k :CHIP 8 7 6 5 R1064 1k :CHIP Vcc 0 - + 1 2 3 R080 0 :CHIP 4 0 - + VDD R079 0 :CHIP D028 1SS355TE-17 C095 2200 10V R1068 2.2k :CHIP C028 3p CJ:CHIP R023 4.7k :CHIP C029 39p CH:CHIP C1007 0.1 B:CHIP R1071 22k :CHIP C041 10 C040 10 C039 10 C038 10 R1021 4.7k :CHIP R1020 4.7k :CHIP EEPWC HOST G1 HOST G2 R1015 1k :CHIP R1062 1k :CHIP C1004 0.01 B:CHIP C037 10 C036 0.022 B:CHIP C5008 47 25V R5003 0 :CHIP 14 13 12 11 10 9 GS5001 3 4 C5005 47 25V R5010 0 :CHIP 1 2 5 7 8 6 8 7 GEOMAGNETIC SENSOR R5005 22k :CHIP C5009 0.1 25V B:CHIP R5006 R5007 1k 10k :CHIP :CHIP 2 R5011 10k :CHIP 3 R5015 C5004 C5003 C5002 100 47 10 1k 16V :CHIP 25V 4 6 R037 10k :CHIP 5 1 C023 0.01 B:CHIP R056 10k :CHIP R057 10k :CHIP C006 C013 C014 0.01 22 22p CH:CHIP B:CHIP 2 C027 0.1 B:CHIP 8 3 7 4 C007 R066 22p 1k CH:CHIP :CHIP R077 10k :CHIP R084 10k :CHIP 6 IC002 MM1170BFB WDT 5 +15V STBY+5V VY VX HDSW LED1 LED0 ECO INPUT_SW PRT_DET D013 HZS10NB2TD R029 10k :CHIP R067 10k :CHIP C024 C025 0.001 2200p B:CHIP B:CHIP C003 0.01 B:CHIP C053 0.01 B:CHIP Q008 DTC114GKAT146 SW C033 C026 100 0.01 25V B:CHIP R049 10k :CHIP R035 10k :CHIP C086 0.01 B:CHIP R1069 1k :CHIP IC003 M24C16-MN6T EEP ROM A0 R078 1M :CHIP X001 24.756MHz C1003 47 25V WDP STBY+5V C042 0.01 B:CHIP C043 22 P82 SDA1 SCL1 GND1 P50/X1OUT VDD2 RESET P90 P55/INT5 P54/INT4 P53/INT3 P52/INT2 P51/INT0 TEST ICE P35/SCOUT P34/CLK P33/WR P32/RD P47/D7 VDD1 P46/D6 P45/D5 P44/D4 P43/D3 P42/D2 P41/D1 P40/D0 P31/CSIO P30/A8 P17/A7 P16/A6 P15/A5 P14/A4 P13/A3 P12/A2 P11/A1 P10/A0 MVBIAS VPP R091 1k :CHIP 158 GND20 R1066 10k :CHIP C090 0.01 B:CHIP 157 UPWM22 D027 1SS355TE-17 R093 R092 1k 1k :CHIP:CHIP C031 10 R095 R094 1k 1k :CHIP:CHIP 155 VDD17 R1065 1.5M :CHIP DSDA1 DSCL1 154 VDD16 VCC TC C022 0.01 B:CHIP C021 0.01 B:CHIP 148 UPWM17 R1017 1k :CHIP R042 10k :CHIP C051 0.01 B:CHIP 147 VDD15 R1016 1k :CHIP R1004 1k :CHIP C050 10 C045 0.022 B:CHIP C046 0.022 B:CHIP C047 0.022 B:CHIP C048 0.01 B:CHIP C049 10 146 VDD14 VX VY 139 VDD13 R097 R098 R096 4.7k 10k 10k :CHIP :CHIP :CHIP 137 VDD12 A1 RESET HVDET 134 GND14 A2 NC C015 0.01 B:CHIP C016 0.01 B:CHIP C017 0.01 B:CHIP C019 0.01 B:CHIP 130 GND13 WC CK VS THDET ABLDET C020 AIN5 AIN6 AIN7 AIN8 AIN9 AIN10 AVDD2 AIN11 AIN12 AIN13 GND5 INT1 P92 P93 P94 P95 P96 UOUT7 UOUT8 VDD3 VDD UBI5 UIN1 UIN2 GND6 UIN3 UIN4 UIN5 UIN6 GND7 UPWM1 VDD5 VDD6 UPWM2 GND8 GND9 UPWM3 VDD7 VDD8 UPWM4 129 GND12 SCL RCT R061 1k :CHIP CLPDLY R090 10k :CHIP HPHASESW R1018 1k :CHIP VRET C018 0.01 0.01 B:CHIP HTR B:CHIP R1036 PWR_SW 100 :CHIP DGS HSOUT1 R1019 MOIREPLS 1k :CHIP C005 150p CH:CHIP R036 2.2k :RN-CP SOG R1013 2.2k :CHIP R1012 2.2k :CHIP R1010 1k :CHIP 125 VDD9 VSS GND ENV KEYDET MOIRECONT 124 UPWM6 D029 HZS5.1NB2TD C062 470 10V C055 47 25V C058 2200p CH:CHIP 127 VDD10 R1001 R1003 1k 1k R1002 R099 1k :CHIP :CHIP1k :CHIP :CHIP 132 VDD11 R1005 1k :CHIP 142 UPWM14 C044 0.022 B:CHIP OFFDET VSAWRST VSH HPLL AFCSW C061 0.01 B:CHIP VS1 HS/CS1 HS/CS2 VS2 R043 1k :CHIP C097 10 123 GND11 SDA VCC I HSOUT HFBP HFREQ HPHASE DVSHAPE VSHPLVL R1009 1k :CHIP R1011 1k :CHIP C098 0.01 B:CHIP MOIREPLS 122 UPWM5 bc3 bc2 bc1 5-26 5-25 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 8 7 6 S3 143 GND17 C052 100 16V J VCC+4.5V VDC MOIRE R1014 1k :CHIP C1006 2200p B:CHIP C054 0.1 B:CHIP GND 141 GND16 STBY+5V R1044 R1008 4.7k 4.7k :RN-CP :CHIP C056 22 160 VDD18 5 SDA SCL 159 GND21 4 TXD RXD 156 UPWM21 LCCLB LCCRB ab5 ab4 ab3 C059 C057 10 10 STBY+5V H 151 GND19 153 UPWM20 3 INPUTSEL Q012 DTC124EKA INV. 152 UPWM19 LCCLT LCCRT 2 CBLK 150 GND18 149 UPWM18 G 145 HDCONT F 1 S4 S2 S1 S0 CLP HCONV LCCNS IC001 CXD8744Q CPU/DSP 140 UPWM13 ROTATION 144 UPWM15 HLINBAL 138 UPWM12 HCENT 133 UPWM10 HSP STBY+5V S6 S5 Q010 2SA1037AK INV. 131 UPWM9 VCONV 135 GND15 E 128 UPWM8 VDF 136 UPWM11 HSIZE 126 UPWM7 HSHPBAL 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 (µ-COM,GEO MAGNETIC SENSOR) STBY+5V 121 GND10 IC006 TL082CPS-E20 ABL DET AMP C AIN4 80 AVSS2 79 AIN3 78 AIN2 77 AIN1 76 AIN0 75 TEMP AVDD1 74 DAC1 73 AVSS1 72 DAC0 71 HDF0 GND4 70 P91 69 UOUT6 68 UOUT5 67 UOUT4 66 OSCVDD 65 XTO 64 XTB 63 OSCVSS 62 PA6 61 PA5 60 PA4 59 PA3 58 GND3 57 PA2 56 PA1 55 PA0 54 UOUT3 53 UOUT2 52 UOUT1 51 GND2 50 UBI4 49 UBI3 48 UBI2 47 UBI1 46 TXD 45 RXD 44 SCK2/P85 43 SDA2 42 SCL2 41 D ab2 ab1 B N -b A 14 13 12 11 10 9 8 7 6 5 4 3 2 1 B-SS3525<U/C>-N..-P2-EPS05 R5507 1.2 :FPRD R5508 1.2 :FPRD R5502 22k :CHIP R5506 6.8k :CHIP R5509 1.2 :FPRD R5503 22k :CHIP C5303 0.1 25V B:CHIP FB5303 1.1µH 7 6 R5319 10k :CHIP 8 5 R5119 10k :CHIP 6 6 C5310 47 25V C5206 0.01 B:CHIP C5404 0.01 B:CHIP R5322 22 1W :RS R5315 22 1W :RS R5122 22 1W :RS R5115 22 1W :RS R5206 22 1W :RS R5607 68 1W :RS R5415 150 2W :RS LCC-RT(+) LCC-RT(-) LCC-RB(+) LCC-RB(-) LCC-LT(+) LCC-LT(-) LCC-LB(+) LCC-LB(-) 1 2 3 4 5 6 7 8 LCC-NS(+) LCC-NS(-) B-SS9116<NH.>-N..-P3-EPS05 1 2 1 2 3 4 5 6 V CONV(+) V CONV(-) H CONV(+) H CONV(-) ROTATION+ ROTATION- LCC-LT LCC-LB LCC-RT LCC-RB LCC-NS V.CONV H.CONV ROTATION I R5510 1.2 :FPRD R5316 10k :CHIP C5308 0.1 25V B:CHIP 9 4 R5308 4.7 :CHIP 10 3 FB5301 1.1µH C5301 0.1 25V B:CHIP FB5103 1.1µH 7 R5313 10k :CHIP C5304 0.01 B:CHIP 2 C5306 0.1 25V B:CHIP C5103 0.1 25V B:CHIP C5108 0.1 25V B:CHIP R5108 4.7 :CHIP 5 8 4 9 3 R5113 10k :CHIP 6 R5208 R5205 6.8k 10k :CHIP :CHIP C5101 0.1 25V B:CHIP 7 FB5201 1.1µH 8 C5110 47 25V 2 R5109 4.7 :CHIP C5106 0.1 25V B:CHIP 9 FB5101 1.1µH 1 10 R5309 4.7 :CHIP 1 C5305 47 25V R5310 10k :CHIP R5116 10k :CHIP C5105 47 25V R5110 10k :CHIP C5205 0.1 25V B:CHIP C5203 0.1 25V B:CHIP R5209 4.7 :CHIP 5 10 4 R5605 100k :CHIP C5606 0.01 B:CHIP 3 FB5401 1.1µH 7 R5406 R5413 27k 100k :CHIP :CHIP C5607 0.1 25V B:CHIP R5603 15k :CHIP 2 C5602 0.1 B:CHIP FB5601 1.1µH 1 R5610 4.7 :CHIP R5602 22k :CHIP R5604 22k :CHIP R5410 22k :CHIP C5401 0.1 25V B:CHIP C5406 0.1 25V B:CHIP R5409 4.7 :CHIP 5 8 4 9 3 10 2 C5409 0.01 B:CHIP 1 R5407 33k :CHIP CN5002 8P YEL :S-MICRO -15V +15V LCCLB STBY+5V ac1 bc3 STBY+5V LCCLT LCCRB C5501 47 LCCRT LCCNS R5207 10k :CHIP R5504 47k :CHIP R5505 47k :CHIP R5408 4.7 :CHIP N -c C5413 0.1 25V B:CHIP 5-28 5-27 ROTATION HCONV VCONV FB5403 1.1µH N -c board l + + + + +15V R5416 22k :CHIP R5422 120 2W :RS Ò N -b board VEE VEE VEE VEE R5419 100k :CHIP Schematic diagram - C5403 0.01 B:CHIP Schematic diagram OUT2 + OUT2 + OUT2 + - C5408 470p B:CHIP H OUT2 + CN5003 2P WHT :S-MICRO V.S2 V.S2 V.S2 - CN5001 6P WHT :S-MICRO G VCC OUT1 VCC OUT1 VCC OUT1 V.S2 -15V V.S1 V.S1 V.S1 VCC OUT1 -15V IC5301 LA6515 AMP IC5101 LA6515 AMP +15V IC5201 LA6515 AMP IC5401 LA6515 AMP D V.S1 E bc2 bc1 C 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B F (H.V.CONV,LCC) N — N BOARD (Conductor Side) — 1 2 3 µ-COM, V.CONV, H.CONV, LCC, GEO MAGNETIC SENSOR • N BOARD SEMICONDUCTOR LOCATION — N BOARD (Component Side) — 1 2 IC Component ( Conductor Side ) ( Side ) IC001 IC002 IC003 IC004 IC005 IC006 IC010 IC011 IC012 IC5101 IC5201 IC5301 IC5401 A C-2 C-2 C-2 B-2 B-2 D-1 C-2 B-2 B-2 A-2 B-2 A-1 B-1 A A-2 B-2 A-2 B-2 TRANSISTOR Component ( Conductor Side ) ( Side ) Q001 Q002 Q003 Q004 Q005 Q006 Q007 Q008 Q010 Q011 Q012 B C-1 C-1 C-1 B-1 C-1 C-1 B-3 C-2 C-1 C-2 D-2 * 1 1 1 2 2 2 1 1 1 2 2 B DIODE Component ( Conductor Side ) ( Side ) D001 D002 D003 D004 D005 D006 D007 D008 D009 D010 D011 D012 D013 D014 D015 D016 D017 D018 D020 D021 D022 D023 D024 D025 D026 D027 D028 D029 D036 D038 D040 C D A-1 A-1 C-3 B-2 A-2 A-2 C-3 C-3 C-3 A-2 C-3 C-2 B-2 B-2 B-1 B-1 B-1 C-3 C-3 B-2 B-2 B-1 B-2 D-2 D-2 D-3 D-3 D-3 C-1 B-1 A-1 A-1 C-1 C-1 C-1 A-1 C-1 C-2 B-2 B-2 B-2 B-1 D-1 D-1 C-1 D-1 * 7 7 6 7 – – – – – – – – – 8 8 – – – 3 3 8 8 8 6 6 3 3 – – 3 – C D CRYSTAL ( X001 Conductor Side C-2 ) (Component Side ) C-1 : Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) * 5-29 5-30 3 (5) Schematic Diagram of G Board 1 2 3 4 5 7 6 8 9 10 11 12 14 13 A G(POWER SUPPLY) CN604 1P IC650 DM-57N +220V SHUNT REG 5.7 GND 1 5 R653 470 2.5 4 3 180 2 B R649 47k :FPRD C661 2200p 1kV B C662 0.01 :PT T620 PIT CN654 8P WHT :S-MICRO 1 R652 470k :CHIP R650 2.2k :CHIP D650 D4SBL40 L650 22µH 5 9 8 7 12 11 L610 AFC R654 1 1/2W :RF C651 4.7 250V C650 100 250V 6 1 2 3 4 5 6 7 8 H CENT H H CENT N H CENT L TO D BOARD +220V CN508 +220V N.C GND GND 7 D610 D4SB60L D613 RM11A 0 GND 2.5 COMP 13.7 VCC 380 CATHODE R615 6.8k 3 4 D 5 6 7 8 9 10 C614 100p :CHIP Q621 2SC3311A REG SW 3 R611 0.47 2W R610 0.33 2W C610 330 450V R630 3.3 :FPRD C607 470p 250V B E1 C622 470p 1kV :HR D690 1SS119 4 181 R614 100 R634 1M 1/2W 379 1 2 3 0 D637 1SS119 1 C629 0.01 :PT 8 AC L NC AC N H 1 2 3 R693 68 1/2W DGC 3 5 2 14.7 15V 4 6 1 D692 1SS119 THP601 CN601 4P WHT :VH DGC NC NC DGC C601 1 275V 6 VDR602 Q691 2SC3311A RELAY DRIVE 0 1 2 3 1.5 R695 C634 4.7k 1000p :CHIP B:CHIP 2.5 0 2.1 3 SG601 AC INLET F601 6.3A 7 C624 0.33 :MPS D654 D2S4MTA1 C659 2200 10V 14.8 D634 1SS119 R617 1k 4 11.9 IN OUT GND 3 C666 10 6 7 5 5 D683 1SS119 14.3 0.2 0.7 R662 10k :CHIP C663 22 3 2 4 1 R683 C687 10 2.2k :CHIP 6.8 Q670 R684 10k 1.2 2SA1037AK PROTECT R685 6.8 1k :CHIP IN OUT GND 6.8 :CHIP D680 YG802C09 3 Q667 2SA1037AK PROTECT R688 150k :RN D664 RD22ESB2 4.0 R681 4.0 10k :CHIP R682 1k R666 :CHIP 10k :CHIP R668 33k :RN 4.0 0 R667 47k :CHIP C665 47 10V 993 Q630 2SK2647-01MR REG SW L680 22µH 0 C680 6800 10V R618 1 2W :RS C682 R670 R671 4700p 12k 12k :PT :RN-CP:RN-CP 3 2 C633 2200p B:CHIP PH630 ON3171-R C630 470p B:CHIP 3 2.5 1 2 R686 220 6.7 :CHIP R687 22k :CHIP R678 1.5 3W :RS C681 47 10V IC651 BA00AST-V5 HEATER REG 1 2.4 R616 6.8k :RN-CP IC652 BA05ST-V5 STBY+5V REG 5.6 IC680 HA17431PA-TZ RECT R672 3.6k :RN-CP 1 2 R673 10k :CHIP 3 4 5 1 2 3 C683 47 10V 4 C685 R675 100 5.1k 10V :RN-CP 3.5 R674 100k :CHIP 5 R676 3.3k :RN-CP C684 100 10V R677 2.7k :RN-CP 4.7 CN650 7P WHT :S-MICRO 1.2 Q671 2SA1037AK HEATER SW 1 2 3 4 5 6 7 D681 RD5.6ESB2 5.6 1 2 3 4 I B-SS3525<U/C>-G..-EPS05 Schematic diagram G board l 5-31 TO A BOARD CN405 R663 10k :CHIP C686 47 10V 2 IC653 BA05T 1W+5V REG STBY+5V 1W+5V GND +80V N.C +220V N.C +12V HEATER Q653 2SC2412K PROTECT 5.0 1 6.1 TO D BOARD CN501 R680 180k :RN R664 R665 10k 2.2k :CHIP :CHIP 0.1 6 5 R658 10k :CHIP Q651 Q654 2SC2458 R659 1k POWER SW :CHIP 2SA1037AK SW 11.4 D665 D663 1SS1191SS119 11.4 R661 100 Q652 2SC2412K 0.1 PROTECT 0.2 Q650 2SA1309A POWER SW 3 3 C667 47 16V D660 RD22ESB2 R660 10k :CHIP 1 2 3 4 5 6 7 8 9 IC654 µPC2912HF +12V REG D661 RD12ESB2 R655 4.7k :CHIP 14.3 7 8 11.2 C625 0.15 :MPS 0.3 R636 R632 22k 120 3.2 :RN D666 1SS119 D656 1SS119 +12V +15V GND -15V GND +80V CN652 9P WHT :S-MICRO R656 1 1/2W :FPRD T621 PRT 8 2 4.9 R609 6.8k R608 :CHIP 10k :CHIP D653 D2S4MTA1 C658 2200 10V 4 4 4 R694 C692 0.1 10k :CHIP B:CHIP C660 47 PH620 ON3171-R S 5 IC630 FA13842P REG RY603 CN602 3P WHT :VH 0 16.1 T601 :LFT 2 R626 1 1W :RS 4 4.7 4 C657 R638 47 0.1 25V :RF L653 22µH 2 C631 100 25V 4.9 C602 1 275V C656 2200 25V 1 C626 0.15 :MPS T630 SRT 3 G 351 C627 470p 1kV :HR D633 ERB38-06V1 D631 D1NL20U 1.4 R607 100k :CHIP 12 2 2 R613 47k :CHIP FB630 0.45µH D635 RD20ESB2 R601 330k 1/2W :SURGE 1 R623 100k 1W :RS D620 1SS119 D632 P6KE200AG23 189 R604 470k :CHIP 11 C655 47 25V R657 1 R606 100k :CHIP VDR601 16.1 R602 27k 2W :RS R605 470k :CHIP 0.5 C604 470p 250V B C603 470p 250V B TO J BOARD CN891 0 Q633 2SC2412K VCC SW FB632 1.1µH B2 D612 15.2 R612 10k 1SS119 2SC4015 VCC SW Q632 2SC4015 VCC SW 2 1 1 Q610 2SA1309A 15.9 VCC SW 188 CN603 3P L652 22µH C654 2200 25V R624 100k 1W :RS R625 1 1W :RS C623 0.33 :MPS R628 68k :CHIP R621 18k R629 22k :CHIP R603 470k AC L OUT NC AC L IN -1.1 348 R622 47k :CHIP 1 R635 27k 2W Q631 :RS E2 R627 22k :CHIP R696 150 1/4W R633 1M 1/2W F B1 R637 0.1 :RF D655 0.47 D1NL20U :FPRD C612 C613 0.22 47 :MPS 2 TH601 E CN653 6P WHT :S-MICRO 1 2 3 4 5 6 10 C2 -1.1 -1.0 C611 1 400V 9 D652 D4SBS4 380 C1 C653 4.7 100V 4.8 CTL 5.5 Vcc GND 5.0 OUT VADJ 1.2 2 4 3 348 Q603 MX0842AB-F REG OUT START UP JW604 1 C620 0.027 800V :PP C621 470p 1kV :HR PS650 2.0A JW605 DRAIN 240 GATE 90.6 AC SEN 0.1 SOURCE 2.4 L SEN C605 4700p 250V R620 0.1 1/2W :RF C652 100 100V 2.8 CTL 6.8 Vcc GND 5.0 OUT NC IC610 MZ1530 PFI L611 68µH RY602 15V 8 D682 RD9.1ESB C606 4700p 250V L651 22µH D651 D1NL20U 1 2 3 4 5 6 C 5-32 STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND TO D BOARD CN502 G POWER SUPPLY — G BOARD — 1 2 3 4 • G BOARD SEMICONDUCTOR LOCATION 5 IC IC610 IC630 IC650 IC651 IC652 IC653 IC654 IC680 A A-4 C-3 A-1 C-1 C-1 C-1 B-1 C-2 TRANSISTOR Q603 Q610 Q621 Q630 Q631 Q632 Q633 Q650 Q651 Q652 Q653 Q654 Q667 Q670 Q671 Q691 B A-3 C-2 C-3 C-3 B-3 C-3 C-3 B-2 B-1 C-1 B-1 B-2 C-1 C-2 C-1 C-2 *– – – – – – 1 – – 1 1 1 1 1 1 – DIODE D610 D612 D613 D620 D631 D632 D633 D634 D635 D637 D650 D651 D652 D653 D654 D655 D656 D660 D661 D663 D664 D665 D666 D680 D681 D682 D683 D690 D692 C NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. B-4 C-2 A-4 C-2 C-2 B-3 B-3 C-3 C-3 C-3 A-2 B-2 A-1 A-2 A-1 B-2 B-2 B-1 C-2 C-1 B-1 B-1 C-2 B-2 C-1 C-1 C-2 C-3 C-4 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) 5-33 5-34 5-5. SEMICONDUCTORS BA00AST-V5 BA05ST-V5 LA6500-FA BA9759F-E2 n M52749FP-TP HA17431PA HA17431PA-TZ MX0842AB-F 2SC4015TV2 n D1NL20U-TR D2S4MF D2S4MTA1 FMQ-G5GS RD9.1ES-L2 RD9.1ES-T1B 1PS226-115 CATHODE 1 E TOP VIEW 1 C B TOP VIEW 18pin SOP 42pin SOP 1 5 M52757FP-TP CXD8744Q-0007 H8D2972 n BA05T 2SA1049-GR 2SA1049TP-GR 2SC2458-YGR 2SC2458TP-YGR TOP VIEW 1 1 3 8 160pin QFP 2 3 BA10324AF-E2 SN74AHCT74PWR SN74HC04ANS SN74HC04ANSR XRA10324AF B µPC2912HF (12) ~ ~ – n D5SC4M 1PS184-115 TOP VIEW 1 10pin SIP LA7841L MARKING SIDE VIEW MARKING SIDE VIEW 1 G 12 5pin SIP 1 7pin SIP FA13842P M24C16-MN6T MM1170BFB LA7865M-TLM n 36 19 3 DTA114GKAT146 DTA114TUA-T106 DTA124EUA-T106 DTC114GKA DTC114GKAT146 DTC124EK DTC124EKA-T146 2SA1036K-Q 2SA1036K-T-146-Q 2SA1037AK-T146-QR 2SA1037AK-T146-R 2SA1162-G 2SB709A-QRS-TX 2SC1623-L5L6 2SC2411K-CQ 2SC2411K-T-146-CQ 2SC2412K-T-146-QR TOP VIEW 1 C TOP VIEW B 8pin DIP 1 18 EC B S D 2SJ569LS-CB11 2SK2655-01R-F165 2SK3262-01MR-F119 2SB1565EF 2SC3746 2SC5022-02 D S G B C E 2SC2362K-G 2SC2362KG-AA 2SK2103T100 G D S n MZ1530 2SK2647-01MR-F91 DTA124ESA DTA124ESA-TP 2SA1175-HFE 2SA1309A-QRSTA 2SC2459-GR-TPE4 2SC2784 2SC2785-HFE 2SC3311A-QRSTA MARKING SIDE VIEW 20pin SOP 1 1 15pin SIP 10 HZS10NB2TD HZS12NB2TD HZS13NB2TD HZS16NB2TD HZS33NB2 HZS33NB2TD HZS4.7NB2 HZS4.7NB2TD HZS5.1NB2TD HZS5.6NB2TD MTZJ-T-77-39B MTZJ-39B RD10ESB2 RD12ES-B2 RD12ES-T1B2 RD13ES-B2 RD20ES-B2 RD20ES-T1B2 RD22ES-B2 RD22ES-T1B2 RD5.1ESB2 RD5.6ES-T1B2 RD5.6ESB2 RD6.8ES-B2 1SS119-25 1SS119-25TD 1SS133T-77 CATHODE ANODE E C B 2SC3209LK 2SC3209LK-TP ERA22-06AVRBT ERA22-08 ERA34-10TP1 ERB38-06V1 GP08D GP08DPKG23 HSS83TD P6KE200AG23 RD2.2M-T1B RGP02-20EL-6394 ANODE CATHODE G D YG911S3R CATHODE ANODE 1PS181-115 S E C B ANODE 5-35 E C B ANODE (RED) YG802C09 ON3171-R 5-36 ANODE CATHODE ANODE (GRN) CATHODE LETTER SIDE 1SS376TE-17 SPR-325MVW ANODE E FA4301 EGP10D EGP10GPKG23 ERA91-02 ERA91-02TP1 CATHODE BA9758FS-E2 TOP VIEW + – 2SA1358-Y 2SC3421-Y MARKING SIDE VIEW NJM2904M NJM2904M(TE2) TL082CPS-E20 NJM082M 24LC21AT/SN 8pin SOP B 2SD2394-EF ~ 14pin SOP n C ~ DM-57N TOP VIEW E LA6515 28pin SOP 1 CATHODE + 36pin SOP CXD9514M 1 n 1 CATHODE 17 1 1 RM11A RM11C ANODE TOP VIEW C E 10 1SS355TE-17 HSU83TRF D4SB60L D4SBL40 D4SBS4 D4SBS4-F n 1 ANODE 2SC5570(LBSONY) CPD-E500/E500E SECTION 6 EXPLODED VIEWS • Items with no part number and no description are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column. • Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified ! marked are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 6-1. CHASSIS z x x 7-685-648-79 7-685-663-71 7-685-646-79 7-685-881-09 f +BVTP 3X12 +BVTP 4X16 +BVTP 3X8 +BVTT 4X8 15 5 4 14 16 2 17 12 3 18 13 11 1 10 [U/C model] [AEP model] 9 19 7 5 8 6 REF.NO. PART NO. 1 1 1 2 3 4 5 6 7 7 7 8 9 DESCRIPTION REMARK REF.NO. PART NO. * A-1346-859-B D BOARD, COMPLETE [AEP] 2 * A-1346-827-B D BOARD, COMPLETE 2 [U/C for Japan-made set] * A-1346-860-B D BOARD, COMPLETE 2 [U/C for Mexico-made set] ! X-4560-175-1 TRANSFORMER ASSY, FLYBACK (NX-4502//J1D4) 4-062-115-01 SCREW +P 3.5X20 TYPE2 * 4-060-359-01 HOLDER, PRINTED CIRCUIT BOARD * 3-701-903-11 HOLDER, PRINTED CIRCUIT BOARD 4-070-730-01 HOLDER, PRINTED CIRCUIT BOARD * A-1316-480-A G BOARD, COMPLETE [AEP] * A-1316-443-B G BOARD, COMPLETE [U/C for Japan-made set] * A-1316-481-A G BOARD, COMPLETE [U/C for Mexico-made set] ! 1-251-382-31 INLET, AC 3P (WITH NOISE FILTER) 4-205-206-01 SCREW (HD15) [AEP] 6-1 9 10 11 11 11 DESCRIPTION REMARK 7-685-881-09 SCREW +BVTP 4X8 (S) [U/C] 4-074-915-01 COVER, PIG TAIL [only U/C] * A-1298-988-B A BOARD, COMPLETE [AEP] * A-1299-191-A A BOARD, COMPLETE [U/C for Japan-made set] * A-1299-135-A A BOARD, COMPLETE [U/C for Mexico-made set] 12 13 14 15 15 1-900-246-08 1-900-250-06 * 4-069-570-01 4-071-452-11 4-071-493-11 CONNECTOR ASSY (F) CONNECTOR ASSY (F) SPACER, PRINTED CIRCUIT BOARD CABINET [AEP] CABINET [U/C] 16 17 17 18 19 * 4-063-711-01 4-039-358-01 7-685-663-71 4-389-025-11 1-792-123-11 SUPPORT, HV CABLE SCREW (4X16), (+) BV TAPPING [AEP] SCREW +BVTP 4X16 TYPE2 IT-3 [U/C] SCREW (M4) (EXT TOOTH WASHER) CORD, CONNECTION [only U/C] CPD-E500/E500E 6-2. PICTURE TUBE x f 7-685-663-71 7-685-881-09 +BVTP 4X16 +BVTT 4X8 The components identified ! marked are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 70 71 69 73 67 74 75 76 56 63 68 62 61 REF.NO. PART NO. 54 55 55 55 56 56 56 57 58 59 60 61 58 59 72 51 54 57 60 53 53 54 66 54 52 51 51 52 52 53 65 64 X-4037-550-1 X-4200-569-1 4-071-152-22 4-204-957-01 3-653-339-21 55 DESCRIPTION REMARK BEZEL ASSY [U/C] BEZEL ASSY [AEP] BUTTON, POWER [U/C] BUTTON, POWER [AEP] SPRING, COMPRESSION [U/C] REF.NO. PART NO. 52,53 52,53 4-071-155-02 BUTTON, MENU [U/C for Mexico-made set] 4-204-970-01 BUTTON, MENU [AEP] * A-1388-260-B J BOARD, COMPLETE [AEP] * A-1388-250-B J BOARD, COMPLETE [U/C for Japan-made set] * A-1388-261-B J BOARD, COMPLETE [U/C for Mexico-made set] * 4-394-972-21 X-4036-844-2 * 4-061-996-11 ! 8-738-813-61 ! 8-451-509-11 CAP, POWER STAND ASSY CUSHION ITC ASSY (21TKC-R1) DEFLECTION YOKE Y21TKM-M 59 61-63 6-2 REMARK 65 ! 1-452-912-61 NECK ASSEMBLY (NA-2914) 2-162-100-21 SPACER, DEFLECTION YOKE * 4-047-316-01 SPRING, EXTENSION [U/C for Japan-made set, AEP] * 4-061-573-01 SPRING, TENSION [U/C for Mexico-made set] ! 1-419-130-21 COIL, LANDING CORRECTION 66 67 68 69 69 ! 1-419-128-21 ! 1-419-129-21 4-062-670-01 4-203-648-01 4-365-808-01 62 63 64 64 3-653-339-11 SPRING, COMPRESSION [AEP] * A-1372-799-A H1 BOARD, COMPLETE [U/C for Japan-made set] * A-1372-770-A H1 BOARD, COMPLETE [U/C for Mexico-made set] * A-1646-206-A H1 BOARD, COMPLETE [AEP] 4-070-665-02 BUTTON, MENU [U/C for Japan-made set] DESCRIPTION 70 71 71 71 72 72 73 74 75 76 COIL, DEGAUSSING COIL, LANDING CORRECTION SPACER, PICTURE TUBE SCREW (5), SELF TAPPING [AEP] SCREW (5), TAPPING [U/C] 4-070-730-01 HOLDER, PRINTED CIRCUIT BOARD * A-1394-950-B N BOARD, COMPLETE [AEP] * A-1394-984-A N BOARD, COMPLETE [U/C for Japan-made set] * A-1394-973-A N BOARD, COMPLETE [U/C for Mexico-made set] 7-685-663-71 SCREW +BVTP 4X16 TYPE2 IT-3 [U/C] 4-039-358-01 4-308-870-00 1-452-032-00 1-452-094-00 4-051-736-21 SCREW (4X16), (+) BV TAPPING [AEP] CLIP, LEAD WIRE MAGNET, DISK; 10mm φ MAGNET, ROTATABLE DISK; 15mm φ PIECE A (90), CONV. CORRECT CPD-E500/E500E 6-3. PACKING MATERIALS The components identified ! marked are critical for safety. Replace only with the part number specified. 109 105 106 107 108 Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 103 104 101 102 REF.NO. PART NO. 101 101 101 102 102 102 103 103 103 104 DESCRIPTION REMARK REF.NO. PART NO. * 4-075-604-01 INDIVIDUAL CARTON [U/C for Japan-made set] * 4-074-479-01 INDIVIDUAL CARTON [U/C for Mexico-made set] * 4-205-252-01 CARTON [AEP] * 4-071-781-01 CUSHION (LOWER) (ASSY) [AEP] * 4-071-731-01 CUSHION (LOWER) (ASSY) [U/C for Japan-made set] * 4-072-876-01 CUSHION (LOWER) (ASSY) [U/C for Mexico-made set] * 4-071-780-01 CUSHION (UPPER) (ASSY) [AEP] * 4-071-730-01 CUSHION (UPPER) (ASSY) [U/C for Japan-made set] * 4-072-875-01 CUSHION (UPPER) (ASSY) [U/C for Mexico-made set] * 4-041-927-31 BAG, POLYETHYLENE [U/C for Japan-made set] 6-3 104 104 105 105 106 106 107 107 108 108 109 DESCRIPTION REMARK * 4-047-293-01 BAG, POLYETHYLENE [U/C for Mexico-made set] * 4-368-079-01 BAG, POLYETHYLENE [AEP] ! 1-782-783-31 CORD SET, POWER [U/C] ! 1-782-784-21 CORD SET, POWER [AEP] 4-075-164-11 MANUAL, INSTRUCTION [U/C] 4-075-164-21 1-772-380-11 1-772-380-21 1-785-512-21 MANUAL, INSTRUCTION [AEP] DISK, INFORMATION [AEP] DISK, INFORMATION [U/C] CONNECTOR, DSUB (15P CHANGER) [U/C] 1-785-512-31 CONNECTOR, DSUB (15P CHANGER) [AEP] 1-791-500-11 CABLE [only AEP] The components identified ! marked are critical for safety. Replace only with the part number specified. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. SECTION 7 A ELECTRICAL PARTS LIST REF.NO. PART NO. NOTE: DESCRIPTION The components identified ! marked are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. REMARK identified REF.NO.by PART DESCRIPTION REMARK The components [ in NO. this • Items marked " * " are not stocked since manual have been carefully factory- they are seldom required for routine selected for each set in order to satisfy service. Some delay should be anticipated regulations regarding X-ray radiation. when ordering these items. Should replacement be required, replace only with the value originally used. RESISTORS • All resistors are in ohms • All variable and adjustable resistors have • F : nonflammable characteristic curve B, unless otherwise noted. When indicating parts by reference number, please include the board name. REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. REMARK * A-1298-988-B A BOARD, COMPLETE [AEP] * A-1299-135-A A BOARD, COMPLETE [U/C for Mexico-made set] * A-1299-191-A A BOARD, COMPLETE [U/C for Japan-made set] *************************** DESCRIPTION REMARK C302 C303 1-104-664-11 ELECT 47µF 1-163-021-91 CERAMIC CHIP0.01µF C304 1-104-664-11 ELECT C307 C308 1-164-004-11 CERAMIC CHIP0.1µF 1-164-004-11 CERAMIC CHIP0.1µF 20% 25V 10% 50V [AEP] 20% 25V [AEP] 10% 25V 10% 25V C309 C310 C312 C313 C314 1-163-227-11 1-163-275-11 1-164-489-11 1-164-489-11 1-164-004-11 CERAMIC CHIP10pF CERAMIC CHIP0.001µF CERAMIC CHIP0.22µF CERAMIC CHIP0.22µF CERAMIC CHIP0.1µF 0.5pF 5% 10% 10% 10% 50V 50V 16V 16V 25V C315 C320 C401 C402 C403 1-104-341-11 1-104-341-11 1-126-964-11 1-104-664-11 1-163-259-91 FILM 0.1µF FILM 0.1µF ELECT 10µF ELECT 47µF CERAMIC CHIP220pF 10% 10% 20% 20% 5% 250V 250V 50V 25V 50V CERAMIC CHIP220pF CERAMIC CHIP0.1µF CERAMIC CHIP0.01µF CERAMIC CHIP0.01µF CERAMIC CHIP0.01µF 5% 10% 10% 10% 10% 50V 25V 50V 50V 50V 47µF 7-682-950-01 SCREW +PSW 3X12 (IC403) <CAPACITOR> C101 C102 C103 1-163-021-91 CERAMIC CHIP 0.01µF 1-104-664-11 ELECT 47µF 1-163-021-91 CERAMIC CHIP 0.01µF C104 1-104-664-11 ELECT C107 1-164-004-11 CERAMIC CHIP 0.1µF 10% 50V 20% 25V 10% 50V [AEP] 20% 25V [AEP] 10% 25V C108 C109 C110 C112 C113 1-164-004-11 1-163-229-11 1-163-275-11 1-164-489-11 1-164-489-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 12pF CERAMIC CHIP 0.001µF CERAMIC CHIP 0.22µF CERAMIC CHIP 0.22µF 10% 5% 5% 10% 10% 25V 50V 50V 16V 16V C404 C405 C406 C407 C408 1-163-259-91 1-164-004-11 1-163-021-91 1-163-021-91 1-163-021-91 C114 C115 C120 C201 C202 1-164-004-11 1-104-341-11 1-104-341-11 1-163-021-91 1-104-664-11 CERAMIC CHIP 0.1µF FILM 0.1µF FILM 0.1µF CERAMIC CHIP 0.01µF ELECT 47µF 10% 10% 10% 10% 20% 25V 250V 250V 50V 25V C410 C411 1-163-021-91 CERAMIC CHIP0.01µF 1-104-664-11 ELECT 47µF C411 1-126-934-11 ELECT C413 1-163-021-91 CERAMIC CHIP0.01µF C203 1-163-021-91 CERAMIC CHIP 0.01µF C413 1-216-025-91 RES, CHIP C204 1-104-664-11 ELECT C205 C206 C207 1-163-021-91 CERAMIC CHIP 0.01µF 1-109-982-11 CERAMIC CHIP 1µF 1-164-004-11 CERAMIC CHIP 0.1µF 10% 50V [AEP] 20% 25V [AEP] 10% 50V 10% 10V 10% 25V C208 C209 C210 C212 C213 1-164-004-11 1-163-227-11 1-163-275-11 1-164-489-11 1-164-489-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 10pF CERAMIC CHIP 0.001µF CERAMIC CHIP 0.22µF CERAMIC CHIP 0.22µF 10% 0.5pF 5% 10% 10% 25V 50V 50V 16V 16V C415 C416 C417 C419 C420 1-164-489-11 1-126-961-11 1-104-574-11 1-162-318-11 1-164-489-11 CERAMIC CHIP0.22µF ELECT 2.2µF CERAMIC 0.0047µF CERAMIC 0.001µF CERAMIC CHIP0.22µF 10% 20% 10% 10% 10% 16V 50V 2KV 500V 16V C214 C215 C216 C220 C301 1-164-004-11 1-104-341-11 1-163-021-91 1-104-341-11 1-163-021-91 CERAMIC CHIP 0.1µF FILM 0.1µF CERAMIC CHIP 0.01µF FILM 0.1µF CERAMIC CHIP 0.01µF 10% 10% 10% 10% 10% 25V 250V 50V 250V 50V C421 C422 C423 C424 C425 1-163-021-91 1-164-489-11 1-104-664-11 1-162-318-11 1-163-251-11 CERAMIC CHIP0.01µF CERAMIC CHIP0.22µF ELECT 47µF CERAMIC 0.001µF CERAMIC CHIP100pF 10% 10% 20% 10% 5% 50V 16V 25V 500V 50V C426 C427 C430 1-163-251-11 CERAMIC CHIP100pF 1-163-235-11 CERAMIC CHIP22pF 1-163-021-91 CERAMIC CHIP0.01µF 47µF 47µF 7-1 220µF 100 10% 50V 20% 25V [U/C] 20% 16V [AEP] 10% 50V [AEP] 5% 1/10W [U/C] 5% 50V 5% 50V 10% 50V CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. A REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK C431 C432 1-163-275-11 CERAMIC CHIP0.001µF 1-164-489-11 CERAMIC CHIP0.22µF 5% 50V 10% 16V D402 D403 8-719-066-11 DIODE 1PS184-115 8-719-982-36 ZENER DIODE MTZJ-39B C433 C434 C435 C436 C437 1-162-318-11 1-162-318-11 1-163-021-91 1-164-489-11 1-126-934-11 10% 10% 10% 10% 20% D405 D406 D407 8-719-911-19 DIODE 1SS119-25 8-719-062-51 DIODE 1PS226-115 8-719-062-51 DIODE 1PS226-115 CERAMIC 0.001µF CERAMIC 0.001µF CERAMIC CHIP0.01µF CERAMIC CHIP0.22µF ELECT 220µF 470µF 500V 500V 50V 16V 16V [U/C] C437 1-126-935-11 ELECT C438 C440 C441 C442 1-115-339-11 1-163-021-91 1-163-021-91 1-163-021-91 CERAMIC CHIP0.1µF CERAMIC CHIP0.01µF CERAMIC CHIP0.01µF CERAMIC CHIP0.01µF 20% 16V [AEP] 10% 50V 10% 50V 10% 50V 10% 50V C443 C444 C446 C449 C450 1-163-021-91 1-162-318-11 1-104-664-11 1-109-982-11 1-107-823-11 CERAMIC CHIP0.01µF CERAMIC 0.001µF ELECT 47µF CERAMIC CHIP1µF CERAMIC CHIP0.47µF 10% 10% 20% 10% 10% C456 1-164-489-11 CERAMIC CHIP0.22µF C457 C458 C459 C462 1-163-021-91 1-115-339-11 1-128-560-11 1-115-339-11 C463 C464 C467 1-163-021-91 CERAMIC CHIP0.01µF 1-163-021-91 CERAMIC CHIP0.01µF 1-107-957-11 ELECT 1µF 50V 500V 25V 10V 16V <FERRITE BEAD> FB102 FB202 FB302 FB402 FB403 1-500-419-22 1-500-419-22 1-500-419-22 1-412-911-11 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH FB404 FB405 FB406 FB411 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH <IC> CERAMIC CHIP0.01µF CERAMIC CHIP0.1µF ELECT 22µF CERAMIC CHIP0.1µF 10% 16V [AEP] 10% 50V 10% 50V 20% 100V 10% 50V 10% 50V 10% 50V 20% 250V IC401 IC402 IC403 IC404 IC405 8-759-584-87 8-759-584-86 8-749-015-91 8-759-585-72 8-759-701-01 IC M52757FP-TP IC M52749FP-TP IC FA4301 IC CXD9514M IC NJM2904M IC406 8-749-015-92 IC H8D2972 IC407 8-759-925-74 IC SN74HC04ANS <COIL> <CONNECTOR> CN401 1-793-183-11 CN402*1-564-509-11 CN403 1-784-463-11 CN405*1-564-524-11 CN406*1-766-179-11 L402 L403 L404 L405 CONNECTOR, D SUB 15P [AEP] PLUG, CONNECTOR 6P CONNECTOR, FFC/FPC 21P PLUG, CONNECTOR 9P PIN, CONNECTOR (PC BOARD) 2P 1-412-529-11 1-412-537-31 1-414-940-21 1-412-529-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 22µH 100µH 100µH 22µH <IC LINK> PS401!1-533-590-31 LINK, IC (1A/90V AC, 60V DC) <DIODE> D101 D102 D103 D105 D106 8-719-062-51 8-719-062-51 8-719-066-10 8-719-051-85 8-719-052-12 DIODE 1PS226-115 DIODE 1PS226-115 [AEP] DIODE 1PS181-115 DIODE HSS83TD DIODE 1SS376TE-17 D107 D201 D202 D203 D205 8-719-052-12 8-719-062-51 8-719-062-51 8-719-066-10 8-719-051-85 DIODE 1SS376TE-17 DIODE 1PS226-115 DIODE 1PS226-115 [AEP] DIODE 1PS181-115 DIODE HSS83TD D206 D207 D301 D302 D303 8-719-052-12 8-719-052-12 8-719-062-51 8-719-062-51 8-719-066-10 DIODE 1SS376TE-17 DIODE 1SS376TE-17 DIODE 1PS226-115 DIODE 1PS226-115 [AEP] DIODE 1PS181-115 D305 D306 D307 8-719-051-85 DIODE HSS83TD 8-719-052-12 DIODE 1SS376TE-17 8-719-052-12 DIODE 1SS376TE-17 <TRANSISTOR> Q101 Q201 Q301 Q401 Q402 8-729-120-28 8-729-120-28 8-729-120-28 8-729-120-28 8-729-050-41 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SJ360TE12L Q406 Q407 Q410 8-729-216-22 TRANSISTOR 2SA1162-G 8-729-028-74 TRANSISTOR DTA114TUA-T106 8-729-032-61 TRANSISTOR 2SC5022-02 <RESISTOR> 7-2 R101 R103 1-215-394-00 METAL 1-215-394-00 METAL 75 75 1% 1% R105 R106 1-216-017-91 RES,CHIP 1-216-017-91 RES, CHIP 47 47 5% 5% 1/4W 1/4W [AEP] 1/10W 1/10W [AEP] The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK REF.NO. PART NO. R107 1-216-045-00 RES,CHIP 680 5% 1/10W R109 R110 R111 R112 R113 1-216-678-11 1-216-097-91 1-216-041-00 1-216-009-91 1-216-017-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 13K 100K 470 22 47 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R114 R115 R116 R117 R118 1-216-009-91 1-219-742-11 1-216-065-91 1-216-121-91 1-216-121-91 RES,CHIP CARBON RES,CHIP RES,CHIP RES,CHIP 22 47 4.7K 1M 1M 5% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R119 R120 R121 R122 R128 1-216-077-91 1-216-113-00 1-216-113-00 1-216-081-00 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 15K 470K 470K 22K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R130 R137 R138 R161 R201 1-216-113-00 1-249-413-11 1-216-017-91 1-216-041-00 1-215-394-00 RES,CHIP CARBON RES,CHIP RES,CHIP METAL 470K 470 47 470 75 5% 5% 5% 5% 1% 1/10W 1/4W 1/10W 1/10W 1/4W R202 R203 1-216-097-91 RES,CHIP 1-215-394-00 METAL 100K 75 5% 1% R205 R206 1-216-017-91 RES,CHIP 1-216-017-91 RES,CHIP 47 47 5% 5% R207 1-216-045-00 RES,CHIP 680 5% 1/10W 1/4W [AEP] 1/10W 1/10W [AEP] 1/10W R209 R210 R211 R212 R213 1-216-678-11 1-216-097-91 1-216-033-00 1-216-009-91 1-216-017-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 13K 100K 220 22 47 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R214 R215 R216 R217 R218 1-216-009-91 1-219-742-11 1-216-065-91 1-216-121-91 1-216-121-91 RES,CHIP CARBON RES,CHIP RES,CHIP RES,CHIP 22 47 4.7K 1M 1M 5% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R219 R220 R221 R222 R228 1-216-077-91 1-216-113-00 1-216-113-00 1-216-081-00 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 15K 470K 470K 22K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R230 R237 R238 R261 R301 1-216-113-00 1-249-413-11 1-216-017-91 1-216-041-00 1-215-394-00 RES,CHIP CARBON RES,CHIP RES,CHIP METAL 470K 470 47 470 75 5% 5% 5% 5% 1% 1/10W 1/4W 1/10W 1/10W 1/4W R303 1-215-394-00 METAL 75 1% R305 R306 1-216-017-91 RES,CHIP 1-216-017-91 RES,CHIP 47 47 R307 R309 1-216-045-00 RES,CHIP 1-216-678-11 METAL CHIP 680 13K 1/4W [AEP] 5% 1/10W 5% 1/10W [AEP] 5% 1/10W 0.5% 1/10W R310 1-216-097-91 RES,CHIP 100K 5% 1/10W 7-3 A DESCRIPTION REMARK R311 R312 R313 R314 1-216-033-00 1-216-009-91 1-216-017-91 1-216-009-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP 220 22 47 22 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R315 R316 R317 R318 R319 1-219-742-11 1-216-065-91 1-216-121-91 1-216-121-91 1-216-077-91 CARBON RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47 4.7K 1M 1M 15K 5% 5% 5% 5% 5% 1/2W 1/10W 1/10W 1/10W 1/10W R320 R321 R322 R328 R330 1-216-113-00 1-216-113-00 1-216-081-00 1-216-065-91 1-216-113-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 470K 470K 22K 4.7K 470K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R337 R338 R361 R402 R403 1-249-413-11 1-216-017-91 1-216-041-00 1-216-049-91 1-216-081-00 CARBON RES,CHIP RES,CHIP RES,CHIP RES,CHIP 470 47 470 1K 22K 5% 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R404 R405 R406 R407 R409 1-216-057-00 1-216-045-00 1-216-097-91 1-218-768-11 1-216-129-00 RES,CHIP RES,CHIP RES,CHIP METAL CHIP RES,CHIP 2.2K 680 100K 470K 2.2M 5% 5% 5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R411 R412 R413 R414 R415 1-216-065-91 1-216-105-91 1-216-097-91 1-216-089-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 220K 100K 47K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R417 R418 R419 R420 R421 1-216-121-91 1-260-127-11 1-216-033-00 1-216-025-91 1-216-025-91 RES,CHIP CARBON RES,CHIP RES,CHIP RES,CHIP 1M 220K 220 100 100 5% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R422 R424 R425 1-216-025-91 RES,CHIP 1-216-049-91 RES,CHIP 1-216-049-91 RES,CHIP 100 1K 1K 5% 5% 5% R426 R427 1-216-105-91 RES,CHIP 1-216-049-91 RES,CHIP 220K 1K 5% 5% 1/10W 1/10W 1/10W [AEP] 1/10W 1/10W R428 R430 R431 R436 R438 1-216-025-91 1-216-025-91 1-216-113-00 1-216-057-00 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 470K 2.2K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R439 R441 R442 R443 R444 1-216-041-00 1-216-121-91 1-216-049-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 470 1M 1K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R445 1-216-025-91 RES,CHIP 100 5% R446 1-216-025-91 RES,CHIP 100 5% R447 1-216-017-91 RES,CHIP 47 5% R448 1-216-017-91 RES,CHIP 47 5% 1/10W [AEP] 1/10W [AEP] 1/10W [AEP] 1/10W [AEP] CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. AG REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. R449 1-216-081-00 RES,CHIP 22K 5% 1/10W R450 R451 R453 R454 R455 1-216-065-91 1-216-115-00 1-216-073-00 1-216-129-00 1-216-097-91 4.7K 560K 10K 2.2M 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R456 1-216-025-91 RES,CHIP 100 5% R457 R458 R459 R460 1-211-895-11 1-219-398-51 1-211-895-11 1-216-073-00 METAL METAL METAL RES,CHIP 10M 2.2M 10M 10K 1/10W [AEP] 10% 1/4W 5% 1W 10% 1/4W 5% 1/10W R461 R463 R464 R488 R490 1-216-105-91 1-216-097-91 1-216-057-00 1-216-089-91 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 220K 100K 2.2K 47K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R491 1-216-065-91 RES,CHIP 4.7K 5% 1/10W RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP <SPARK GAP> SG101 SG201 SG301 SG401 SG402 1-576-354-21 1-576-354-21 1-576-354-21 1-576-354-21 1-519-422-11 GAP, SPARK GAP, SPARK GAP, SPARK GAP, SPARK GAP, SPARK <SOCKET> SK401!1-451-499-11 SOCKET, PICTURE TUBE <CRYSTAL> X401 The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION C607 C610 C611 C612 1-113-900-11 1-117-849-11 1-137-479-11 1-136-169-00 CERAMIC ELECT FILM FILM C613 C614 C620 C621 C622 1-126-967-11 1-163-251-11 1-128-990-11 1-104-330-91 1-104-330-91 C623 C624 C625 C626 C627 REMARK 470pF 330µF 1µF 0.22µF 10% 20% 10% 5% 250V 450V 400V 50V ELECT 47µF CERAMIC CHIP100pF FILM 27000pF CERAMIC 470pF CERAMIC 470pF 20% 5% 5% 10% 10% 50V 50V 800V 1KV 1KV 1-136-171-00 1-136-171-00 1-136-167-00 1-136-167-00 1-104-330-91 FILM FILM FILM FILM CERAMIC 5% 5% 5% 5% 10% 50V 50V 50V 50V 1KV C629 C630 C631 C633 C634 1-137-370-11 1-163-005-11 1-104-665-11 1-164-161-11 1-163-009-11 FILM 0.01µF CERAMIC CHIP470pF ELECT 100µF CERAMIC CHIP0.0022µF CERAMIC CHIP0.001µF 5% 10% 20% 10% 10% 50V 50V 25V 50V 50V C650 C651 C652 C653 C654 1-107-656-11 1-107-651-11 1-128-563-11 1-128-581-11 1-126-943-11 ELECT ELECT ELECT ELECT ELECT 100µF 4.7µF 100µF 4.7µF 2200µF 20% 20% 20% 20% 20% 250V 250V 100V 100V 25V C655 C656 C657 C658 C659 1-104-664-11 1-126-943-11 1-104-664-11 1-126-927-11 1-128-339-11 ELECT ELECT ELECT ELECT ELECT 47µF 2200µF 47µF 2200µF 2200µF 20% 20% 20% 20% 20% 25V 25V 25V 10V 10V C660 C661 C662 C663 C665 1-126-967-11 1-107-429-11 1-137-370-11 1-126-965-11 1-107-909-11 ELECT CERAMIC FILM ELECT ELECT 47µF 0.0022µF 0.01µF 22µF 47µF 20% 10% 5% 20% 20% 50V 1KV 50V 50V 10V C666 C667 C680 C681 C682 1-126-964-11 1-107-909-11 1-115-747-51 1-104-664-11 1-137-368-11 ELECT ELECT ELECT ELECT FILM 10µF 47µF 0.0068F 47µF 0.0047µF 20% 20% 20% 20% 5% 50V 16V 10V 10V 50V C683 C684 C685 C686 C687 1-104-664-11 1-128-526-11 1-128-526-11 1-104-664-11 1-126-964-11 ELECT ELECT ELECT ELECT ELECT 47µF 100µF 100µF 47µF 10µF 20% 20% 20% 20% 20% 10V 10V 10V 10V 50V C692 1-115-339-11 CERAMIC CHIP0.1µF 0.33µF 0.33µF 0.15µF 0.15µF 470pF 1-781-472-21 VIBRATOR, CERAMIC (8MHz) **************************************************************************** * A-1316-443-B G BOARD, COMPLETE [U/C for Japan-made set] * A-1316-480-A G BOARD, COMPLETE [AEP] * A-1316-481-A G BOARD, COMPLETE [U/C for Mexico-made set] *************************** 1-533-223-11 HOLDER, FUSE (F601) 4-382-854-11 SCREW (M3X10), P, SW (+) (D610, D652, D680, IC610, IC654, Q603, Q630) 10% 50V <CONNECTOR> <CAPACITOR> C601 ! 1-113-513-11 C602 ! 1-113-513-11 C603 ! 1-113-900-51 C604 ! 1-113-900-51 C605 ! 1-113-926-91 FILM FILM CERAMIC CERAMIC CERAMIC 1µF 1µF 470pF 470pF 0.0047µF C606 ! 1-113-926-91 CERAMIC 0.0047µF 20% 20% 10% 10% CN601*1-580-689-11 CN602*1-691-960-11 CN603*1-691-960-11 CN650*1-564-510-11 CN652*1-564-512-11 275V 275V 250V 250V 250V PIN, CONNECTOR (PC BOARD) 4P PIN, CONNECTOR (PC BOARD) 3P PIN, CONNECTOR (PC BOARD) 3P PLUG, CONNECTOR 7P PLUG, CONNECTOR 9P CN653*1-564-509-11 PLUG, CONNECTOR 6P CN654*1-564-511-11 PLUG, CONNECTOR 8P 250V 7-4 The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK REF.NO. PART NO. <DIODE> G DESCRIPTION REMARK L651 L652 1-414-742-21 INDUCTOR 1-412-529-11 INDUCTOR 22µH 22µH L653 L680 1-412-529-11 INDUCTOR 1-414-742-21 INDUCTOR 22µH 22µH D610 ! 8-719-510-53 D612 8-719-911-19 D613 8-719-304-63 D620 8-719-911-19 D631 8-719-063-73 DIODE D4SB60L DIODE 1SS119-25 DIODE RM11C DIODE 1SS119-25 DIODE D1NL20U-TR D632 D633 D634 D635 D637 8-719-059-23 8-719-069-63 8-719-911-19 8-719-110-53 8-719-911-19 DIODE P6KE200AG23 DIODE ERB38-06V1 DIODE 1SS119-25 ZENER DIODE RD20ESB2 DIODE 1SS119-25 D650 D651 D652 D653 D654 8-719-064-49 8-719-063-73 8-719-052-91 8-719-022-97 8-719-022-97 DIODE D4SBL40 DIODE D1NL20U-TR DIODE D4SBS4-F DIODE D2S4MF DIODE D2S4MF D655 D656 D660 D661 D663 8-719-063-73 8-719-911-19 8-719-110-57 8-719-110-31 8-719-911-19 DIODE D1NL20U-TR DIODE 1SS119-25 ZENER DIODE RD22ESB2 ZENER DIODE RD12ESB2 DIODE 1SS119-25 Q603 Q610 Q621 Q630 Q631 8-729-045-39 8-729-119-76 8-729-119-78 8-729-045-03 8-729-041-66 TRANSISTOR MX0842AB-F TRANSISTOR 2SA1175-HFE TRANSISTOR 2SC2785-HFE TRANSISTOR 2SK2647-01MR-F91 TRANSISTOR 2SC4015TV2 D664 D665 D666 D680 D681 8-719-110-57 8-719-911-19 8-719-911-19 8-719-989-87 8-719-109-89 ZENER DIODE RD22ESB2 DIODE 1SS119-25 DIODE 1SS119-25 DIODE YG802C09 ZENER DIODE RD5.6ESB2 Q632 Q633 Q650 Q651 Q652 8-729-041-66 8-729-120-28 8-729-119-76 8-729-230-45 8-729-120-28 TRANSISTOR 2SC4015TV2 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1175-HFE TRANSISTOR 2SC2458-YGR TRANSISTOR 2SC1623-L5L6 D682 D683 D690 D692 8-719-121-26 8-719-911-19 8-719-911-19 8-719-911-19 ZENER DIODE RD9.1ESL2 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 Q653 Q654 Q667 Q670 Q671 8-729-120-28 8-729-026-49 8-729-026-49 8-729-026-49 8-729-026-49 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SA1037AK-T146-R Q691 8-729-119-78 TRANSISTOR 2SC2785-HFE <PHOTO COUPLER> PH620 8-749-924-35 PHOTO COUPLER ON3171-R PH630 8-749-924-35 PHOTO COUPLER ON3171-R <IC LINK> PS650!1-533-593-31 LINK, IC (2A/90V AC, 60V DC) <TRANSISTOR> <FUSE> F601 ! 1-576-233-11 FUSE (H.B.C.) (6.3A/250V) <RESISTOR> <FERRITE BEAD> FB630 1-410-396-41 FERRITE FB632!1-410-397-31 FERRITE 0.45µH 1.1µH <IC> IC610 IC630 IC650 IC651 IC652 8-749-015-89 8-759-535-32 8-749-012-49 8-759-592-79 8-759-496-15 IC MZ1530 IC FA13842P IC DM-57N IC BA00AST-V5 IC BA05ST-V5 IC653 8-759-450-47 IC BA05T IC654 8-759-643-66 IC µPC2912HF(12) IC680 8-759-321-95 IC HA17431PA <COIL> L610 L611 L650 1-419-126-21 COIL, CHOKE (AFC) 1-411-674-11 INDUCTOR 68µH 1-414-742-21 INDUCTOR 22µH 216µH 7-5 R601 ! 1-220-825-91 R602 1-216-465-11 R603 1-247-895-91 R604 1-216-113-00 R605 1-216-113-00 CARBON METAL OXIDE CARBON RES,CHIP RES,CHIP 330K 27K 470K 470K 470K 5% 5% 5% 5% 5% 1/2W 2W F 1/4W 1/10W 1/10W R606 R607 R608 R609 R610 1-216-097-91 1-216-097-91 1-216-073-00 1-216-069-00 1-217-152-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL 100K 100K 10K 6.8K 0.33 5% 5% 5% 5% 10% 1/10W 1/10W 1/10W 1/10W 2W R611 R612 R613 R614 R615 1-217-153-00 1-249-429-11 1-216-089-91 1-247-807-31 1-249-427-11 METAL CARBON RES,CHIP CARBON CARBON 0.47 10K 47K 100 6.8K 10% 5% 5% 5% 5% 2W 1/4W 1/10W 1/4W 1/4W R616 R617 R618 R620 R621 1-216-671-11 1-249-417-11 1-216-369-00 1-202-933-61 1-249-432-11 METAL CHIP CARBON METAL OXIDE FUSIBLE CARBON 6.8K 1K 1 0.1 18K 0.5% 5% 5% 10% 5% 1/10W 1/4W 2W F 1/2W F 1/4W CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. GD REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK R622 R623 R624 R625 R626 1-216-089-91 1-218-642-11 1-218-642-11 1-216-349-00 1-216-349-00 RES,CHIP METAL OXIDE METAL OXIDE METAL OXIDE METAL OXIDE 47K 100K 100K 1 1 5% 5% 5% 5% 5% 1/10W 1W F 1W F 1W F 1W F R695 R696 R627 R628 R629 R630 R632 1-216-683-11 1-216-695-11 1-216-683-11 1-249-387-11 1-215-399-00 METAL CHIP METAL CHIP METAL CHIP CARBON METAL 22K 68K 22K 3.3 120 0.5% 0.5% 0.5% 5% 1% 1/10W 1/10W 1/10W 1/4W F 1/4W RY602!1-755-318-11 RELAY, POWER RY603!1-755-067-21 RELAY R633 R634 R635 R636 R637 1-260-135-11 1-260-135-11 1-216-465-11 1-247-863-91 1-219-134-11 CARBON CARBON METAL OXIDE CARBON FUSIBLE 1M 1M 27K 22K 0.1 5% 5% 5% 5% 10% 1/2W 1/2W 2W F 1/4W 1/4W SG601!1-533-982-11 GAP, SPARK R638 R649 R650 R652 R653 1-219-134-11 1-249-437-11 1-216-057-00 1-216-113-00 1-249-413-11 FUSIBLE CARBON RES,CHIP RES,CHIP CARBON 0.1 47K 2.2K 470K 470 10% 5% 5% 5% 5% 1/4W 1/4W F 1/10W 1/10W 1/4W R654 R655 R656 R657 R658 1-211-796-11 1-216-065-91 1-260-292-11 1-249-443-11 1-216-073-00 FUSIBLE RES,CHIP CARBON CARBON RES,CHIP 1 4.7K 1 0.47 10K 5% 5% 5% 5% 5% 1/2W F 1/10W 1/2W 1/4W F 1/10W R659 R660 R661 R662 R663 1-216-049-91 1-216-073-00 1-247-807-31 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP CARBON RES,CHIP RES,CHIP 1K 10K 100 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W 1/10W 1/10W R664 R665 R666 R667 R668 1-216-073-00 1-216-057-00 1-216-073-00 1-216-089-91 1-215-457-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL 10K 2.2K 10K 47K 33K 5% 5% 5% 5% 1% 1/10W 1/10W 1/10W 1/10W 1/4W R670 R671 R672 R673 R674 1-216-677-11 1-216-677-11 1-216-664-11 1-216-073-00 1-216-097-91 METAL CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 12K 12K 3.6K 10K 100K 0.5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R675 R676 R677 R678 R680 1-216-668-11 1-216-663-11 1-216-661-11 1-216-391-11 1-215-475-00 METAL CHIP METAL CHIP METAL CHIP METAL OXIDE METAL 5.1K 3.3K 2.7K 1.5 180K 0.5% 0.5% 0.5% 5% 1% 1/10W 1/10W 1/10W 3W F 1/4W R681 R682 R683 R684 R685 1-216-073-00 1-216-049-91 1-216-057-00 1-216-073-00 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 1K 2.2K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R686 R687 R688 R693 R694 1-216-033-00 1-216-081-00 1-215-473-00 1-260-085-11 1-216-073-00 RES,CHIP RES,CHIP METAL CARBON RES,CHIP 220 22K 150K 68 10K 5% 5% 1% 5% 5% 1/10W 1/10W 1/4W 1/2W 1/10W 1-216-065-91 RES,CHIP 1-249-407-11 CARBON 4.7K 150 5% 5% 1/10W 1/4W <RELAY> <SPARK GAP> <TRANSFORMER> T601 ! 1-429-180-11 TRANSFORMER, LINE FILTER T620 1-433-894-11 TRANSFORMER, CONVERTER (PIT) T621 1-429-992-11 TRANSFORMER, CONVERTER (PRT) T630 1-433-895-31 TRANSFORMER, CONVERTER (SRT) <THERMISTOR> TH601 ! 1-809-260-11 THERMISTOR, POWER THP601! 1-809-827-31 THERMISTOR, POSITIVE <VARISTOR> VDR601! 1-801-268-51 VARISTOR TNR14V471K660 VDR602! 1-810-622-11 VARISTOR *************************************************************************** * A-1346-827-B D BOARD, COMPLETE [U/C for Japan-made set] * A-1346-859-B D BOARD, COMPLETE [AEP] * A-1346-860-B D BOARD, COMPLETE [U/C for Mexico-made set] *************************** 3-710-578-01 4-070-828-01 4-070-829-01 4-070-829-02 4-070-830-01 COVER, VOLUME, 6 MOLD (RV901) INSULATING SHEET (Q515) INSULATING SHEET (IC502) [U/C] INSULATING SHEET (IC502) [AEP] INSULATING SHEET (IC701) 4-382-854-11 SCREW (M3X10), P, SW (+) (IC701, Q704, Q705, Q905, Q906, R918) 7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT(B) (D511, IC502, Q508, Q515, R547) <CAPACITOR> 7-6 C501 C502 C503 C504 C505 1-163-021-91 1-136-169-00 1-163-021-91 1-163-017-00 1-163-021-91 CERAMIC CHIP0.01µF FILM 0.22µF CERAMIC CHIP0.01µF CERAMIC CHIP0.0047µF CERAMIC CHIP0.01µF C506 C507 1-137-194-81 FILM 1-136-169-00 FILM 0.47µF 0.22µF 10% 5% 10% 10% 10% 50V 50V 50V 50V 50V 5% 5% 50V 50V The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK C508 C509 C510 1-126-965-11 ELECT 1-115-521-11 FILM 1-117-398-11 ELECT 22µF 0.82µF 33µF C511 C512 C513 C514 C515 1-163-113-00 1-163-259-91 1-163-017-00 1-106-375-12 1-163-021-91 CERAMIC CHIP 68pF CERAMIC CHIP 220pF CERAMIC CHIP 0.0047µF MYLAR 0.022µF CERAMIC CHIP 0.01µF 5% 50V 5% 50V 10% 50V 200V 10% 50V C516 C517 C518 C519 C520 1-126-935-11 1-163-021-91 1-137-194-81 1-163-021-91 1-107-914-11 ELECT 470µF CERAMIC CHIP 0.01µF FILM 0.47µF CERAMIC CHIP 0.01µF ELECT 1000µF 20% 10% 5% 10% 20% 16V 50V 50V 50V 25V C521 C522 C523 C524 C525 1-117-666-11 1-137-368-11 1-137-368-11 1-163-133-00 1-104-760-11 FILM 0.39µF FILM 0.0047µF FILM 0.0047µF CERAMIC CHIP 470pF CERAMIC CHIP 0.047µF 5% 5% 5% 5% 10% 250V 50V 50V 50V 50V C526 C527 C528 C529 C530 1-163-021-91 1-163-021-91 1-117-663-11 1-104-665-11 1-163-021-91 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF FILM 0.22µF ELECT 100µF CERAMIC CHIP 0.01µF 10% 10% 5% 20% 10% 50V 50V 250V 25V 50V C531 C532 C533 C534 C535 1-107-846-11 1-163-009-11 1-107-889-11 1-107-889-11 1-163-021-91 FILM 0.1µF CERAMIC CHIP 0.001µF ELECT 220µF ELECT 220µF CERAMIC CHIP 0.01µF 5% 10% 20% 20% 10% 250V 50V 25V 25V 50V C536 C537 C538 C539 C540 1-126-967-11 1-113-694-11 1-163-021-91 1-163-017-00 1-106-343-00 ELECT 47µF FILM 0.056µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.0047µF MYLAR 0.001µF 20% 5% 10% 10% 10% 50V 400V 50V 50V 200V C541 C542 C543 C544 C545 1-164-161-11 1-163-021-91 1-135-350-11 1-125-925-11 1-107-597-11 CERAMIC CHIP 0.0022µF CERAMIC CHIP 0.01µF FILM 3600pF FILM MELF 0.027µF CERAMIC 22pF 10% 10% 3% 5% 5% 50V 50V 1.8KV 400V 500V C546 C547 C548 C549 C550 1-107-444-11 1-130-061-91 1-162-134-11 1-130-495-00 1-127-833-11 CERAMIC FILM CERAMIC FILM FILM 5% 5% 10% 5% 5% 2KV 630V 2KV 50V 400V C551 C552 C554 C555 C556 1-163-017-00 1-163-021-91 1-107-444-11 1-107-683-11 1-115-356-11 CERAMIC CHIP 0.0047µF CERAMIC CHIP 0.01µF CERAMIC 100pF ELECT 2.2µF FILM 1.2µF 10% 50V 10% 50V 5% 2KV 250V 5% 250V C557 C558 C559 C560 C561 1-163-021-91 1-104-665-11 1-107-649-11 1-163-021-91 1-104-664-11 CERAMIC CHIP 0.01µF ELECT 100µF ELECT 2.2µF ELECT 0.01µF ELECT 47µF 10% 20% 20% 10% 20% C562 C563 C564 1-163-021-91 CERAMIC CHIP 0.01µF 10% 50V 1-163-011-11 CERAMIC CHIP 0.0015µF 10% 50V 1-126-960-11 ELECT 1µF 20% 50V 100pF 0.0015µF 470pF 0.1µF 0.15µF REF.NO. PART NO. 20% 50V 5% 250V 20% 250V 50V 25V 250V 50V 25V 7-7 D DESCRIPTION REMARK C565 C566 1-164-004-11 CERAMIC CHIP0.1µF 1-137-370-11 FILM 0.01µF 10% 25V 5% 50V C567 C568 C571 C572 C573 1-164-161-11 1-104-760-11 1-163-227-11 1-163-009-11 1-106-375-12 CERAMIC CHIP0.0022µF CERAMIC CHIP0.047µF CERAMIC CHIP10pF CERAMIC CHIP0.001µF MYLAR 0.022µF 10% 10% 0.5pF 10% 50V 50V 50V 50V 200V C574 C575 C577 C701 C702 1-163-017-00 1-163-021-91 1-126-964-11 1-128-560-11 1-128-562-11 CERAMIC CHIP0.0047µF CERAMIC CHIP0.01µF ELECT 10µF ELECT 22µF ELECT 47µF 10% 10% 20% 20% 20% 50V 50V 50V 100V 100V C703 C704 C706 C707 C708 1-104-331-11 1-104-568-11 1-164-004-11 1-130-495-00 1-126-942-61 CERAMIC 0.0022µF CERAMIC 470pF CERAMIC CHIP0.1µF FILM 0.1µF ELECT 1000µF 10% 10% 10% 5% 20% 1KV 2KV 25V 50V 25V C709 C710 C711 C712 C713 1-163-021-91 1-107-894-11 1-163-019-00 1-106-228-00 1-126-942-61 CERAMIC CHIP0.01µF ELECT 220µF CERAMIC CHIP0.0068µF MYLAR 0.22µF ELECT 1000µF 10% 20% 10% 10% 20% 50V 35V 50V 100V 25V C715 C720 C901 C902 C903 1-164-004-11 1-126-964-11 1-163-021-91 1-104-665-11 1-126-964-11 CERAMIC CHIP0.1µF ELECT 10µF CERAMIC CHIP0.01µF ELECT 100µF ELECT 10µF 10% 20% 10% 20% 20% 25V 50V 50V 25V 50V C905 C907 C908 C909 C910 1-163-127-00 1-163-257-11 1-163-021-91 1-126-935-11 1-126-962-11 CERAMIC CHIP270pF CERAMIC CHIP180pF CERAMIC CHIP0.01µF ELECT 470µF ELECT 3.3µF 5% 5% 10% 20% 20% 50V 50V 50V 16V 50V C912 C913 C914 C915 C916 1-106-383-00 1-119-748-11 1-106-383-00 1-136-169-00 1-117-626-11 MYLAR ELECT MYLAR FILM FILM 0.047µF 33µF 0.047µF 0.22µF 2000pF 10% 20% 10% 5% 3% 200V 400V 200V 50V 1.2KV C917 C918 C919 C920 C921 1-117-665-11 1-106-359-00 1-115-350-51 1-137-372-11 1-106-228-00 FILM MYLAR CERAMIC FILM MYLAR 0.33µF 0.0047µF 0.0047µF 0.022µF 0.22µF 5% 250V 10% 100V 2KV 5% 50V 10% 100V C922 C923 C924 C925 C926 1-106-220-00 1-106-355-12 1-106-220-00 1-126-967-11 1-126-964-11 MYLAR MYLAR MYLAR ELECT ELECT 0.1µF 0.0033µF 0.1µF 47µF 10µF 10% 10% 10% 20% 20% 100V 200V 100V 50V 50V C927 C928 C929 C930 C931 1-163-243-11 1-163-133-00 1-164-004-11 1-163-227-11 1-126-964-11 CERAMIC CHIP47pF CERAMIC CHIP470pF CERAMIC CHIP0.1µF CERAMIC CHIP10pF ELECT 10µF 5% 5% 10% 0.5pF 20% 50V 50V 25V 50V 50V C932 C933 C935 1-163-021-91 CERAMIC CHIP0.01µF 1-126-960-11 ELECT 1µF 1-163-275-11 CERAMIC CHIP0.001µF 10% 50V 20% 50V 5% 50V CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. D REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. <CONNECTOR> CN501*1-564-509-11 CN502*1-564-510-11 CN503*1-508-879-11 CN504 1-784-786-11 CN505 1-784-786-11 D923 PLUG, CONNECTOR 6P PLUG, CONNECTOR 7P BASE POST CONNECTOR, FFC 25P CONNECTOR, FFC 25P The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK 8-719-988-61 DIODE 1SS355TE-17 <FERRITE BEAD> FB501 FB502 FB503 FB504 FB505 CN506 1-764-101-11 PIN, CONNECTOR (PC BOARD) 2P CN508*1-564-511-11 PLUG, CONNECTOR 8P CN509*1-778-955-11 PIN, CONNECTOR (PC BOARD) 10P <DIODE> 1-410-397-21 1-410-397-21 1-412-911-11 1-412-911-11 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH FB506 1-410-397-21 FERRITE FB507 1-410-397-21 FERRITE FB901 1-410-397-21 FERRITE 1.1µH 1.1µH 1.1µH D504 D505 D506 D507 D508 8-719-988-61 8-719-110-36 8-719-991-33 8-719-063-89 8-719-031-79 DIODE 1SS355TE-17 ZENER DIODE RD13ESB2 DIODE 1SS133T-77 DIODE YG911S3R DIODE D5SC4M D509 D510 D511 D512 D513 8-719-991-33 8-719-109-85 8-719-066-36 8-719-988-61 8-719-991-33 DIODE 1SS133T-77 ZENER DIODE RD5.1ESB2 DIODE FMQ-G5GS DIODE 1SS355TE-17 DIODE 1SS133T-77 D514 D515 D516 D517 D519 8-719-991-33 8-719-109-89 8-719-991-33 8-719-951-30 8-719-988-61 DIODE 1SS133T-77 ZENER DIODE RD5.6ESB2 DIODE 1SS133T-77 DIODE ERA91-02 DIODE 1SS355TE-17 JR002 JR003 JR004 JR005 JR006 1-216-296-91 1-216-295-91 1-216-295-91 1-216-296-91 1-216-295-91 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 D520 D522 D701 D702 D703 8-719-988-61 8-719-988-61 8-719-991-33 8-719-991-33 8-719-991-33 DIODE 1SS355TE-17 DIODE 1SS355TE-17 DIODE 1SS133T-77 DIODE 1SS133T-77 DIODE 1SS133T-77 JR008 JR009 JR010 JR011 JR012 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-296-91 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 D706 D707 D708 D709 D710 8-719-979-58 8-719-109-85 8-719-908-03 8-719-948-45 8-719-109-85 DIODE EGP10D ZENER DIODE RD5.1ESB2 DIODE GP08D DIODE ERA22-08 ZENER DIODE RD5.1ESB2 JR013 JR014 JR015 JR016 1-216-295-91 1-216-296-91 1-216-296-91 1-216-295-91 SHORT SHORT SHORT SHORT 0 0 0 0 D901 D902 D904 D905 D906 8-719-991-33 8-719-110-31 8-719-988-61 8-719-110-36 8-719-063-89 DIODE 1SS133T-77 ZENER DIODE RD12ESB2 DIODE 1SS355TE-17 ZENER DIODE RD13ESB2 DIODE YG911S3R D907 D908 D909 D910 D912 8-719-930-97 8-719-018-82 8-719-930-97 8-719-991-33 8-719-979-58 ZENER DIODE HZS16NB2TD DIODE RGP02-20EL-6394 ZENER DIODE HZS16NB2TD DIODE 1SS133T-77 DIODE EGP10D INDUCTOR COIL, CHOKE COIL, CHOKE COIL, CHOKE COIL, CHOKE 100µH 2.2mH 1mH 4.7mH 5mH D913 D914 D915 D917 D918 8-719-991-33 8-719-991-33 8-719-929-72 8-719-988-61 8-719-991-33 DIODE 1SS133T-77 DIODE 1SS133T-77 ZENER DIODE HZS33NB2 DIODE 1SS355TE-17 DIODE 1SS133T-77 D919 D920 D921 D922 8-719-991-33 8-719-928-85 8-719-988-61 8-719-018-82 DIODE 1SS133T-77 ZENER DIODE HZS4.7NB2 DIODE 1SS355TE-17 DIODE RGP02-20EL-6394 <IC> IC501 IC502 IC503 IC701 IC901 8-759-585-82 8-759-803-42 8-759-058-50 8-759-444-82 8-759-585-81 IC BA9759F-E2 IC LA6500-FA IC XRA10324AF IC LA7841L IC BA9758FS-E2 <CHIP CONDUCTOR> <COIL> L501 L502 L503 L504 L505 1-412-537-31 1-406-673-11 1-406-671-11 1-406-675-11 1-416-401-31 L901 L902 1-412-537-31 INDUCTOR 100µH 1-406-660-41 COIL, CHOKE 15µH <TRANSISTOR> 7-8 Q501 Q502 Q503 Q504 Q505 8-729-048-49 8-729-120-28 8-729-901-97 8-729-901-87 8-729-901-97 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1036K-Q TRANSISTOR 2SC2411K-CQ TRANSISTOR 2SA1036K-Q Q506 Q507 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119 The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK Q508 Q509 Q510 8-729-048-53 TRANSISTOR 2SJ569LS-CB11 8-729-820-73 TRANSISTOR 2SC3746 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119 Q511 Q512 Q513 Q514 Q515 8-729-048-49 8-729-048-49 8-729-048-49 8-729-140-50 8-729-048-48 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SC3209LK TRANSISTOR 2SC5570 (LBSONY) Q516 Q517 Q518 Q519 Q520 8-729-024-95 8-729-048-49 8-729-019-01 8-729-033-25 8-729-120-28 TRANSISTOR 2SB1565EF TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SD2394-EF TRANSISTOR DTC114GKA TRANSISTOR 2SC1623-L5L6 Q521 Q522 Q523 Q524 Q525 8-729-120-28 8-729-120-28 8-729-120-28 8-729-026-49 8-729-048-49 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SK3262-01MR-F119 Q526 Q701 Q702 Q703 Q704 8-729-027-35 8-729-800-32 8-729-178-43 8-729-204-91 8-729-207-82 TRANSISTOR DTA143TKA-T146 TRANSISTOR 2SC2362K-G TRANSISTOR 2SC2784-E TRANSISTOR 2SA1049-GR TRANSISTOR 2SC3421-Y Q705 Q706 Q707 Q903 Q904 8-729-207-89 8-729-026-49 8-729-046-80 8-729-901-87 8-729-901-97 TRANSISTOR 2SA1358-Y TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SC4634LS-CB11 TRANSISTOR 2SC2411K-CQ TRANSISTOR 2SA1036K-Q Q905 Q906 Q907 Q908 8-729-048-53 8-729-044-21 8-729-033-26 8-729-033-25 TRANSISTOR 2SJ569LS-CB11 TRANSISTOR 2SK2655-01R-F165 TRANSISTOR DTA114GKAT146 TRANSISTOR DTC114GKA REF.NO. PART NO. D DESCRIPTION REMARK R522 R523 R524 R525 1-249-437-11 1-216-033-00 1-216-049-91 1-216-065-91 CARBON RES,CHIP RES,CHIP RES,CHIP 47K 220 1K 4.7K 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/10W R526 R527 R528 R529 R530 1-216-097-91 1-216-673-11 1-216-677-11 1-216-057-00 1-216-049-91 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 100K 8.2K 12K 2.2K 1K 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R531 R532 R533 R534 R535 1-216-097-91 1-215-860-11 1-211-796-11 1-216-689-11 1-216-065-91 RES,CHIP METAL OXIDE FUSIBLE METAL CHIP RES,CHIP 100K 33 1 39K 4.7K 5% 5% 5% 0.5% 5% 1/10W 1W F 1/2W F 1/10W 1/10W R536 R537 R538 R539 R540 1-216-683-11 1-249-437-11 1-216-049-91 1-216-097-91 1-215-909-11 METAL CHIP CARBON RES,CHIP RES,CHIP METAL OXIDE 22K 47K 1K 100K 47 0.5% 5% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 3W F R541 R542 R543 R544 R545 1-216-295-91 1-249-437-11 1-216-677-11 1-216-049-91 1-216-097-91 SHORT CARBON METAL CHIP RES,CHIP RES,CHIP 0 47K 12K 1K 100K 5% 0.5% 5% 5% 1/4W 1/10W 1/10W 1/10W R546 R547 R548 R549 R550 1-216-381-11 1-219-726-11 1-249-437-11 1-260-288-11 1-260-288-11 METAL OXIDE METAL CARBON CARBON CARBON 0.22 2.2 47K 0.47 0.47 5% 5% 5% 5% 5% 3W F 10W 1/4W 1/2W 1/2W R551 R552 R553 R554 R555 1-216-049-91 1-216-097-91 1-247-815-91 1-216-679-11 1-216-675-91 RES,CHIP RES,CHIP CARBON METAL CHIP METAL CHIP 1K 100K 220 15K 10K 5% 5% 5% 0.5% 0.5% 1/10W 1/10W 1/4W 1/10W 1/10W R556 R557 R558 R559 R560 1-216-683-11 1-216-423-11 1-249-437-11 1-216-073-00 1-216-675-91 METAL CHIP METAL OXIDE CARBON RES,CHIP METAL CHIP 22K 27 47K 10K 10K 0.5% 5% 5% 5% 0.5% 1/10W 1W F 1/4W 1/10W 1/10W R561 R562 R563 R564 R565 1-215-443-00 1-216-677-11 1-216-049-91 1-216-677-11 1-216-097-91 METAL METAL CHIP RES,CHIP METAL CHIP RES,CHIP 8.2K 12K 1K 12K 100K 1% 0.5% 5% 0.5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R566 R567 R568 R569 R570 1-216-687-11 1-214-840-00 1-216-665-11 1-216-691-11 1-260-332-51 METAL CHIP METAL METAL CHIP METAL CHIP CARBON 33K 100 3.9K 47K 2.2K 0.5% 1% 0.5% 0.5% 5% 1/10W 1/2W 1/10W 1/10W 1/2W R571 R572 R573 R574 R575 1-249-425-11 1-216-385-11 1-249-437-11 1-216-097-91 1-216-672-11 CARBON METAL OXIDE CARBON RES,CHIP METAL CHIP 4.7K 0.47 47K 100K 7.5K 5% 5% 5% 5% 0.5% 1/4W 3W F 1/4W 1/10W 1/10W R576 R577 1-215-869-11 METAL OXIDE 1K 1-260-310-71 CARBON 33 5% 5% 1W F 1/2W <RESISTOR> R501 R502 R503 R504 R505 1-215-884-11 1-216-059-00 1-216-049-91 1-216-049-91 1-216-049-91 METAL OXIDE RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47 2.7K 1K 1K 1K 5% 5% 5% 5% 5% 2W F 1/10W 1/10W 1/10W 1/10W R506 R507 R508 R509 R510 1-216-049-91 1-216-097-91 1-247-815-91 1-216-049-91 1-216-675-91 RES,CHIP RES,CHIP CARBON RES,CHIP METAL CHIP 1K 100K 220 1K 10K 5% 5% 5% 5% 0.5% 1/10W 1/10W 1/4W 1/10W 1/10W R511 R512 R513 R514 R515 1-216-065-91 1-215-453-00 1-216-049-91 1-216-097-91 1-216-049-91 RES,CHIP METAL RES,CHIP RES,CHIP RES,CHIP 4.7K 22K 1K 100K 1K 5% 1% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 1/10W R516 R517 R518 R519 R520 1-216-049-91 1-216-687-11 1-216-691-11 1-216-081-00 1-247-791-91 RES,CHIP METAL CHIP METAL CHIP RES,CHIP CARBON 1K 33K 47K 22K 22 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W R521 1-216-667-11 METAL CHIP 4.7K 0.5% 1/10W 7-9 CPD-E500/E500E D REF.NO. PART NO. The components identified by [ in this manual have been carefully factoryselected for eachset in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK R578 R579 R580 1-216-049-91 RES,CHIP 1-216-049-91 RES,CHIP 1-214-840-00 METAL 1K 1K 100 5% 5% 1% 1/10W 1/10W 1/2W R581 R582 R583 R584 R585 1-260-316-51 1-214-840-00 1-249-437-11 1-249-437-11 1-216-073-00 CARBON METAL CARBON CARBON RES,CHIP 100 100 47K 47K 10K 5% 1% 5% 5% 5% 1/2W 1/2W 1/4W 1/4W 1/10W R586 R587 R588 R589 R590 1-216-683-11 1-215-886-11 1-260-085-11 1-216-057-00 1-216-057-00 METAL CHIP METAL OXIDE CARBON RES,CHIP RES,CHIP 22K 100 68 2.2K 2.2K 0.5% 5% 5% 5% 5% 1/10W 2W F 1/2W 1/10W 1/10W R591 R593 R594 R595 R597 1-247-807-31 1-216-073-00 1-216-683-11 1-216-659-11 1-216-073-00 CARBON RES,CHIP METAL CHIP METAL CHIP RES,CHIP 100 10K 22K 2.2K 10K 5% 5% 0.5% 0.5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R598 R599 R701 R702 R703 1-216-675-91 1-216-657-11 1-216-049-91 1-249-393-11 1-215-459-00 METAL CHIP METAL CHIP RES,CHIP CARBON METAL 10K 1.8K 1K 10 39K 0.5% 0.5% 5% 5% 1% 1/10W 1/10W 1/10W 1/4W F 1/4W R704 R705 R706 R707 R708 1-216-655-11 1-249-413-11 1-249-389-11 1-249-389-11 1-215-881-11 METAL CHIP CARBON CARBON CARBON METAL OXIDE 1.5K 470 4.7 4.7 15 0.5% 5% 5% 5% 5% 1/10W 1/4W F 1/4W F 1/4W F 2W F R709 R710 R711 R713 R714 1-216-049-91 1-216-073-00 1-216-049-91 1-216-059-00 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 10K 1K 2.7K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R715 R716 R717 R718 R719 1-249-389-11 1-216-689-11 1-216-073-00 1-216-681-11 1-216-663-11 CARBON RES,CHIP RES,CHIP METAL CHIP METAL CHIP 4.7 39K 10K 18K 3.3K 5% 5% 5% 0.5% 0.5% 1/4W F 1/10W 1/10W 1/10W 1/10W R720 R721 R722 R723 R724 1-216-073-00 1-216-073-00 1-260-292-11 1-216-663-11 1-216-659-11 RES,CHIP RES,CHIP CARBON METAL CHIP METAL CHIP 10K 10K 1 3.3K 2.2K 5% 5% 5% 0.5% 0.5% 1/10W 1/10W 1/2W 1/10W 1/10W R725 R726 R727 R728 R729 1-214-798-21 1-214-798-21 1-249-381-11 1-215-865-11 1-260-292-11 METAL METAL CARBON METAL OXIDE CARBON 1.8 1.8 1 220 1 1% 1% 5% 5% 5% 1/2W 1/2W 1/4W F 1W F 1/2W R730 R731 R732 R901 R902 1-216-073-00 1-216-059-00 1-219-510-11 1-216-097-91 1-216-117-00 RES,CHIP RES,CHIP CARBON RES,CHIP RES,CHIP 10K 2.7K 470K 100K 680K 5% 5% 5% 5% 5% 1/10W 1/10W 1/2W 1/10W 1/10W R903 R904 R906 1-216-089-91 RES,CHIP 1-216-033-00 RES,CHIP 1-216-033-00 RES,CHIP 47K 220 220 5% 5% 5% 1/10W 1/10W 1/10W REF.NO. PART NO. The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK R907 R908 1-216-081-00 RES,CHIP 22K 1-216-399-00 METAL OXIDE 6.8 5% 5% 1/10W 3W F R911 R912 R914 R915 R916 1-216-041-00 1-216-049-91 1-247-791-91 1-216-065-91 1-249-397-11 RES,CHIP RES,CHIP CARBON RES,CHIP CARBON 470 1K 22 4.7K 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W 1/10W 1/4W F R917 R918 R919 R920 R921 1-211-824-71 1-219-727-11 1-219-748-11 1-216-089-91 1-249-429-11 FUSIBLE METAL CARBON RES,CHIP CARBON 220 68 4.7K 47K 10K 5% 5% 5% 5% 5% 1/2W F 10W 1/2W 1/10W 1/4W R922 R923 R924 R925 R926 1-249-389-11 1-218-762-11 1-216-073-00 1-220-825-11 1-219-746-11 CARBON METAL CHIP RES,CHIP CARBON CARBON 4.7 270K 10K 330K 1K 5% 0.5% 5% 5% 5% 1/4W F 1/10W 1/10W 1/2W 1/2W R927 R928 R929 R930 R931 1-219-746-11 1-216-668-11 1-216-675-91 1-216-653-11 1-216-653-11 CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 5.1K 10K 1.2K 1.2K 5% 0.5% 0.5% 0.5% 0.5% 1/2W 1/10W 1/10W 1/10W 1/10W R932 R933 R934 R935 R937 1-216-049-91 1-216-687-11 1-216-667-11 1-216-089-91 1-216-065-91 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 1K 33K 4.7K 47K 4.7K 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R939 R940 R941 R943 R945 1-216-049-91 1-216-073-00 1-216-025-91 1-216-065-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 10K 100 4.7K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1501 R1502 R1503 R1504 R1505 1-216-049-91 1-216-033-00 1-216-682-11 1-216-665-11 1-216-667-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 1K 220 20K 3.9K 4.7K 5% 5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R1506 R1507 R1510 R1515 R1517 1-216-049-91 1-216-097-91 1-216-073-00 1-215-909-11 1-216-089-91 RES,CHIP RES,CHIP RES,CHIP METAL OXIDE RES,CHIP 1K 100K 10K 47 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 3W F 1/10W 100 5% 1/10W R1518 1-216-025-91 RES,CHIP <VARIABLE RESISTOR> [ RV901!1-241-767-21 RES, ADJ, CERMET <RELAY> RY501 1-755-198-11 RELAY 7-10 100K (HV ADJ) The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. <SPARK GAP> D H1 JN DESCRIPTION REMARK R804 R811 1-247-815-91 CARBON 1-249-429-11 CARBON 220 10K 5% 5% 1/4W 1/4W <TRANSFORMER> R812 R813 R814 R815 R821 1-249-429-11 1-247-863-91 1-249-441-11 1-215-445-00 1-215-401-11 CARBON CARBON CARBON METAL METAL 10K 22K 100K 10K 150 5% 5% 5% 1% 1% 1/4W 1/4W 1/4W 1/4W 1/4W 1-435-070-11 1-429-301-11 1-431-413-21 1-419-127-11 1-431-414-11 R822 R823 R824 R851 R852 1-215-413-00 1-215-421-00 1-215-425-00 1-249-413-11 1-247-807-31 METAL METAL METAL CARBON CARBON 470 1K 1.5K 470 100 1% 1% 1% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R853 1-247-807-31 CARBON 100 5% 1/4W SG901 1-517-499-21 GAP, SPARK SG902 1-519-422-11 GAP, SPARK SG903 1-519-422-11 GAP, SPARK T501 T502 T503 T505 T701 CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. TRANSFORMER, HORIZONTAL DRIVE TRANSFORMER, FERRITE (HCT) TRANSFORMER, FERRITE (HST) COIL, HORIZONTAL LINEARITY TRANSFORMER, FERRITE (DFT) T901 1-416-402-11 INDUCTOR 500µH T902 ! X-4560-175-1 TRANSFORMER ASSY, FLYBACK (NX-4502//J1D4) <SWITCH> <THERMISTOR> S801 S812 1-771-734-11 SWITCH, TACTILE (MENU) 1-554-303-21 SWITCH, KEY BOARD (RESET) TH501 1-807-796-11 THERMISTOR TH502 1-807-796-11 THERMISTOR <THERMISTOR> TH801 1-807-796-11 THERMISTOR *************************************************************************** * A-1372-770-A H1 BOARD, COMPLETE [U/C for Mexico-made set] * A-1372-799-A H1 BOARD, COMPLETE [U/C for Japan-made set] * A-1646-206-A H1 BOARD, COMPLETE [AEP] **************************** *************************************************************************** * A-1388-250-B J BOARD, COMPLETE [U/C for Japan-made set] * A-1388-260-B J BOARD, COMPLETE [AEP] * A-1388-261-B J BOARD, COMPLETE [U/C for Mexico-made set] ************************** <CAPACITOR> C802 C806 1-126-791-11 ELECT 1-126-786-11 ELECT 10µF 47µF 20% 16V 20% 16V <CONNECTOR> CN891*1-691-960-11 PIN, CONNECTOR (PC BOARD) 3P <CONNECTOR> CN801*1-564-526-11 PLUG, CONNECTOR 11P <SWITCH> S891 ! 1-571-433-31 SWITCH, PUSH (AC POWER) <DIODE> D801 8-719-064-11 DIODE SPR-325MVW (POWER) *************************************************************************** <TRANSISTOR> Q801 Q802 Q803 Q804 8-729-119-78 8-729-119-78 8-729-029-40 8-729-029-40 * A-1394-950-B N BOARD, COMPLETE [AEP] * A-1394-973-A N BOARD, COMPLETE [U/C for Mexico-made set] * A-1394-984-A N BOARD, COMPLETE [U/C for Japan-made set] *************************** TRANSISTOR 2SC2785-HFE TRANSISTOR 2SC2785-HFE TRANSISTOR DTA124ESA TRANSISTOR DTA124ESA <RESISTOR> <CAPACITOR> R801 R802 R803 1-249-417-11 CARBON 1-249-413-11 CARBON 1-247-815-91 CARBON 1K 470 220 5% 5% 5% 1/4W 1/4W 1/4W C001 C002 7-11 1-163-009-11 CERAMIC CHIP0.001µF 1-163-009-11 CERAMIC CHIP0.001µF 10% 50V 10% 50V CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. N REF.NO. PART NO. DESCRIPTION REMARK C003 C005 C006 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-255-11 CERAMIC CHIP 150pF 1-163-235-11 CERAMIC CHIP 22pF 10% 50V 5% 50V 5% 50V C007 C008 1-163-235-11 CERAMIC CHIP 22pF 1-164-004-11 CERAMIC CHIP 0.1µF C009 1-115-339-11 CERAMIC CHIP 0.1µF C010 1-126-967-11 ELECT C011 1-115-339-11 CERAMIC CHIP 0.1µF 5% 50V 10% 25V [AEP] 10% 50V [U/C] 20% 50V [U/C] 10% 50V [AEP] C012 1-126-967-11 ELECT C013 C014 C015 C016 1-126-965-11 1-163-021-91 1-163-021-91 1-163-021-91 ELECT 22µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF 20% 50V [AEP] 20% 50V 10% 50V 10% 50V 10% 50V C017 C018 C019 C020 C021 1-163-021-91 1-163-021-91 1-163-021-91 1-163-021-91 1-163-021-91 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C022 C023 C024 C025 C026 1-163-021-91 1-163-021-91 1-164-161-11 1-163-009-11 1-104-665-11 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 2200PF CERAMIC CHIP 0.001µF ELECT 100µF 10% 10% 10% 10% 20% 50V 50V 50V 50V 25V C027 C028 C029 C031 C033 1-115-339-11 1-163-220-11 1-163-241-11 1-126-964-11 1-163-021-91 CERAMIC CHIP 0.1µF CERAMIC CHIP 3pF CERAMIC CHIP 39pF ELECT 10µF CERAMIC CHIP 0.01µF 10% 50V 0.25pF 50V 5% 50V 20% 50V 10% 50V C036 C037 C038 C039 C040 1-163-037-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 CERAMIC CHIP 0.022µF ELECT 10µF ELECT 10µF ELECT 10µF ELECT 10µF 10% 20% 20% 20% 20% 50V 50V 50V 50V 50V C041 C042 C043 C044 C045 1-126-964-11 1-163-021-91 1-126-965-11 1-163-037-11 1-163-037-11 ELECT 10µF CERAMIC CHIP 0.01µF ELECT 22µF CERAMIC CHIP 0.022µF CERAMIC CHIP 0.022µF 20% 10% 20% 10% 10% 50V 50V 50V 50V 50V C046 C047 C048 C049 C050 1-163-037-11 1-163-037-11 1-163-021-91 1-126-964-11 1-126-964-11 CERAMIC CHIP 0.022µF CERAMIC CHIP 0.022µF CERAMIC CHIP 0.01µF ELECT 10µF ELECT 10µF 10% 10% 10% 20% 20% 50V 50V 50V 50V 50V C051 C052 C053 C054 C055 1-163-021-91 1-126-933-11 1-163-021-91 1-115-339-11 1-104-664-11 CERAMIC CHIP 0.01µF ELECT 100µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF ELECT 47µF 10% 20% 10% 10% 20% 50V 16V 50V 50V 25V C056 C057 C058 C059 1-126-965-11 1-126-964-11 1-164-690-91 1-126-964-11 ELECT 22µF ELECT 10µF CERAMIC CHIP 0.0022µF ELECT 10µF 20% 20% 5% 20% 50V 50V 50V 50V 47µF 47µF REF.NO. PART NO. 7-12 The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK C061 1-163-021-91 CERAMIC CHIP 0.01µF 10% 50V C062 C063 C064 C065 C066 1-126-925-11 1-164-690-91 1-115-419-11 1-126-960-11 1-164-690-91 ELECT 470µF CERAMIC CHIP 0.0022µF CERAMIC CHIP 3300pF ELECT 1µF CERAMIC CHIP 0.0022µF 20% 5% 5% 20% 5% 10V 50V 25V 50V 50V C067 C068 C069 C070 C071 1-164-004-11 1-136-169-00 1-115-339-11 1-126-767-11 1-163-007-11 CERAMIC CHIP 0.1µF FILM 0.22µF CERAMIC CHIP 0.1µF ELECT 1000µF CERAMIC CHIP 680pF 10% 5% 10% 20% 10% 25V 50V 50V 16V 50V C072 C073 C074 C075 C077 1-126-942-61 1-115-339-11 1-163-137-00 1-163-251-11 1-115-339-11 ELECT 1000µF CERAMIC CHIP 0.1µF CERAMIC CHIP 680pF CERAMIC CHIP 100pF CERAMIC CHIP 0.1µF 20% 10% 5% 5% 10% 25V 50V 50V 50V 50V C078 C079 C080 C082 C083 1-136-169-00 1-163-021-91 1-126-967-11 1-104-664-11 1-163-021-91 FILM 0.22µF CERAMIC CHIP 0.01µF ELECT 47µF ELECT 47µF CERAMIC CHIP 0.01µF 5% 10% 20% 20% 10% 50V 50V 50V 25V 50V C084 C085 C086 C087 C089 1-126-964-11 1-163-021-91 1-163-021-91 1-126-964-11 1-163-021-91 ELECT 10µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF ELECT 10µF CERAMIC CHIP 0.01µF 20% 10% 10% 20% 10% 50V 50V 50V 50V 50V C090 C091 C094 C095 C096 1-163-021-91 1-126-933-11 1-164-004-11 1-117-722-11 1-163-021-91 CERAMIC CHIP 0.01µF ELECT 100µF CERAMIC CHIP 0.1µF ELECT 2200µF CERAMIC CHIP 0.01µF 10% 20% 10% 20% 10% 50V 16V 25V 10V 50V C097 C098 C099 C1003 C1004 1-126-964-11 1-163-021-91 1-164-004-11 1-104-664-11 1-163-021-91 ELECT 10µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF ELECT 47µF CERAMIC CHIP 0.01µF 20% 10% 10% 20% 10% 50V 50V 25V 25V 50V C1005 C1006 C1007 C5002 C5003 1-163-005-11 1-164-161-11 1-115-339-11 1-126-964-11 1-126-933-11 CERAMIC CHIP 470pF CERAMIC CHIP 0.0022µF CERAMIC CHIP 0.1µF ELECT 10µF ELECT 100µF 10% 10% 10% 20% 20% 50V 50V 50V 50V 16V C5004 C5005 C5008 C5009 C5101 1-104-664-11 1-104-664-11 1-104-664-11 1-164-004-11 1-164-004-11 ELECT 47µF ELECT 47µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF 20% 20% 20% 10% 10% 25V 25V 25V 25V 25V C5103 C5105 C5106 C5108 C5110 1-164-004-11 1-104-664-11 1-164-004-11 1-164-004-11 1-104-664-11 CERAMIC CHIP 0.1µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF ELECT 47µF 10% 20% 10% 10% 20% 25V 25V 25V 25V 25V C5203 C5205 C5206 C5301 C5303 1-164-004-11 1-164-004-11 1-163-021-91 1-164-004-11 1-164-004-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF 10% 10% 10% 10% 10% 25V 25V 50V 25V 25V The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK C5304 C5305 C5306 C5308 C5310 1-163-021-91 1-104-664-11 1-164-004-11 1-164-004-11 1-104-664-11 CERAMIC CHIP 0.01µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF ELECT 47µF 10% 20% 10% 10% 20% 50V 25V 25V 25V 25V C5401 C5403 C5404 C5406 C5408 1-164-004-11 1-163-021-91 1-163-021-91 1-164-004-11 1-163-005-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF CERAMIC CHIP 470pF 10% 10% 10% 10% 10% 25V 50V 50V 25V 50V C5409 C5413 C5501 C5602 C5606 1-163-021-91 1-164-004-11 1-126-967-11 1-115-339-11 1-163-021-91 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.01µF 10% 10% 20% 10% 10% 50V 25V 50V 50V 50V C5607 1-164-004-11 CERAMIC CHIP 0.1µF REF.NO. PART NO. N DESCRIPTION REMARK D027 D028 D029 D036 D038 8-719-988-61 8-719-988-61 8-719-109-85 8-719-109-89 8-719-045-99 DIODE 1SS355TE-17 DIODE 1SS355TE-17 ZENER DIODE RD5.1ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD2.2M-T1B D040 8-719-109-89 ZENER DIODE RD5.6ESB2 <FERRITE BEAD> 10% 25V FB001 1-410-397-21 FB002 1-410-397-21 FB003 1-410-397-21 FB5101 1-412-911-11 FB5103 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH FB5201 1-412-911-11 FB5301 1-412-911-11 FB5303 1-412-911-11 FB5401 1-412-911-11 FB5403 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH FB5601 1-412-911-11 FERRITE 1.1µH <CONNECTOR> CN001 1-784-500-11 CN002*1-564-511-11 CN007*1-564-512-11 CN010 1-784-786-11 CN011 1-784-786-11 CONNECTOR, FFC/FPC 21P PLUG, CONNECTOR 8P PLUG, CONNECTOR 9P CONNECTOR, FFC 25P CONNECTOR, FFC 25P <SENSOR> GS5001 1-418-473-11 SENSOR UNIT, GEOMAGNETIC CN5001*1-564-509-11PLUG, CONNECTOR 6P CN5002*1-564-511-11PLUG, CONNECTOR 8P CN5003*1-564-505-11PLUG, CONNECTOR 2P <IC> <DIODE> D001 D002 D003 D004 D005 8-719-062-51 8-719-062-51 8-719-109-89 8-719-109-89 8-719-109-89 DIODE 1PS226-115 DIODE 1PS226-115 DIODE 1PS226-115 [AEP] DIODE 1PS226-115 [AEP] ZENER DIODE RD5.6ESB2 [U/C] D006 D007 D008 D009 D010 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-89 ZENER DIODE RD5.6ESB2 [U/C] ZENER DIODE RD5.6ESB2 [U/C] ZENER DIODE RD5.6ESB2 [AEP] ZENER DIODE RD5.6ESB2 [AEP] ZENER DIODE RD5.6ESB2 [AEP] D011 D012 D013 D014 D015 8-719-109-89 8-719-109-89 8-719-110-17 8-719-066-11 8-719-066-11 ZENER DIODE RD5.6ESB2 [U/C] ZENER DIODE RD5.6ESB2 [AEP] ZENER DIODE RD10ESB2 DIODE 1PS184-115 [U/C] DIODE 1PS184-115 [AEP] D016 D017 D018 D020 D021 8-719-109-89 8-719-109-89 8-719-109-89 8-719-988-61 8-719-988-61 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 DIODE 1SS355TE-17 DIODE 1SS355TE-17 D022 D023 D024 D025 D026 8-719-066-11 8-719-066-11 8-719-066-11 8-719-062-51 8-719-062-51 DIODE 1PS184-115 DIODE 1PS184-115 DIODE 1PS184-115 [AEP] DIODE 1PS226-115 DIODE 1PS226-115 IC001 IC002 IC003 IC004 IC005 8-759-658-88 8-759-162-80 8-759-527-77 8-759-639-81 8-759-639-81 IC CXD8744Q-0007 IC MM1170BFB IC M24C16-MN6T IC SN74AHCT74PWR [AEP] IC SN74AHCT74PWR IC006 IC010 IC011 IC012 IC5101 8-759-700-78 8-759-585-70 8-759-442-20 8-759-442-20 8-759-822-07 NJM082M IC LA7865M-TLM IC 24LC21AT/SN [AEP] IC 24LC21AT/SN [U/C] IC LA6515 IC5201 8-759-822-07 IC LA6515 IC5301 8-759-822-07 IC LA6515 IC5401 8-759-822-07 IC LA6515 <COIL> L002 L003 1-406-665-11 COIL, CHOKE 100µH 1-406-671-11 COIL, CHOKE 1mH <TRANSISTOR> 7-13 Q001 Q002 Q003 Q004 Q005 8-729-026-49 8-729-026-49 8-729-026-49 8-729-028-83 8-729-033-26 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SA1037AK-T146-R TRANSISTOR DTA124EUA-T106 TRANSISTOR DTA114GKAT146 Q006 Q007 Q008 8-729-027-49 TRANSISTOR DTC123EKA-T146 8-729-901-00 TRANSISTOR DTC124EK 8-729-033-25 TRANSISTOR DTC114GKA CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. N REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. The components identified ! marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK Q010 Q011 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R R049 R050 1-216-073-00 RES,CHIP 1-216-089-91 RES,CHIP 10K 47K Q012 8-729-901-00 TRANSISTOR DTC124EK R050 1-216-295-91 SHORT 0 5% 5% 1/10W 1/10W [U/C] [AEP] <RESISTOR> R051 1-216-077-91 RES,CHIP 15K 5% 1/10W 1/10W 1/10W [AEP] 1/10W [AEP] 1/10W R051 1-216-049-91 RES,CHIP 1K 5% R052 1-216-077-91 RES,CHIP 15K 5% R052 1-216-049-91 RES,CHIP 1K 5% R053 1-216-065-91 RES,CHIP 4.7K 5% 1/10W 1/10W 1/10W 1/4W [U/C] 1/10W [U/C] R054 R055 1-216-077-91 RES,CHIP 1-216-049-91 RES,CHIP 15K 1K 5% 5% R055 1-216-077-91 RES,CHIP 15K 5% R056 R057 1-216-073-00 RES,CHIP 1-216-073-00 RES,CHIP 10K 10K 5% 5% 1/10W 1/10W [U/C] 1/10W [AEP] 1/10W 1/10W R058 R059 R060 R061 R062 1-216-067-00 1-216-057-00 1-216-057-00 1-216-049-91 1-216-613-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 5.6K 2.2K 2.2K 1K 27 5% 5% 5% 5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R063 R064 R066 R067 R075 1-216-613-11 1-216-613-11 1-216-049-91 1-216-073-00 1-215-407-00 METAL CHIP METAL CHIP RES,CHIP RES,CHIP METAL 27 27 1K 10K 270 0.5% 0.5% 5% 5% 1% 1/10W 1/10W 1/10W 1/10W 1/4W R076 R077 R078 R079 R080 1-215-407-00 1-216-073-00 1-216-121-91 1-216-295-91 1-216-295-91 METAL RES,CHIP RES,CHIP SHORT SHORT 270 10K 1M 0 0 1% 5% 5% 1/4W 1/10W 1/10W R081 R082 R084 R085 R086 1-216-049-91 1-216-049-91 1-216-073-00 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 10K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R090 R091 R092 R093 R094 1-216-073-00 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R095 R096 R097 R098 R099 1-216-049-91 1-216-065-91 1-216-073-00 1-216-073-00 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 4.7K 10K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1001 R1002 R1003 R1004 R1005 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1006 1-216-049-91 RES,CHIP 1K 5% 1/10W R003 R004 R005 1-216-025-91 RES,CHIP 1-216-025-91 RES,CHIP 1-216-025-91 RES,CHIP 100 100 100 5% 5% 5% R006 1-216-025-91 RES,CHIP 100 5% R007 1-216-057-00 RES,CHIP 2.2K 5% R008 R009 R010 R011 1-216-057-00 1-216-057-00 1-216-057-00 1-249-389-11 2.2K 2.2K 2.2K 4.7 5% 5% 5% 5% R012 1-216-017-91 RES,CHIP 47 5% R013 1-216-017-91 RES,CHIP 47 5% R014 R015 1-216-049-91 RES,CHIP 1-249-389-11 CARBON 1K 4.7 5% 5% R016 1-216-017-91 RES,CHIP 47 5% R017 1-216-017-91 RES,CHIP 47 5% R018 1-216-049-91 RES,CHIP 1K 5% R019 R020 R021 R022 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 100 5% 5% 5% 5% 1/10W [AEP] 1/10W 1/10W 1/10W 1/10W R023 R024 R025 R026 R029 1-216-065-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 100 100 100 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R030 R031 R032 R034 R035 1-216-049-91 1-216-669-11 1-216-665-11 1-216-049-91 1-216-065-91 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 1K 5.6K 3.9K 1K 4.7K 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R036 R037 R039 R040 R042 1-216-659-11 1-216-073-00 1-216-025-91 1-216-025-91 1-216-073-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 2.2K 10K 100 100 10K 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R043 R044 R045 R046 1-216-049-91 1-216-657-11 1-216-049-91 1-216-073-00 RES,CHIP METAL CHIP RES,CHIP RES,CHIP 1K 1.8K 1K 10K 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W [AEP] R047 R048 1-216-049-91 RES,CHIP 1-216-049-91 RES,CHIP 1K 1K 5% 5% 1/10W 1/10W RES,CHIP RES,CHIP RES,CHIP CARBON 1/10W [U/C] 1/10W 1/4W [AEP] 1/10W [AEP] 1/10W [AEP] 7-14 1/10W [U/C] 1/10W [AEP] 1/10W [U/C] 1/10W [AEP] 1/10W The components identified ! marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. CPD-E500/E500E Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK R1007 R1008 R1009 R1010 1-216-049-91 1-216-667-11 1-216-049-91 1-216-049-91 RES,CHIP METAL CHIP RES,CHIP RES,CHIP 1K 4.7K 1K 1K 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W R1011 R1012 R1013 R1014 R1015 1-216-049-91 1-216-057-00 1-216-057-00 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 2.2K 2.2K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1016 R1017 R1018 R1019 R1020 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 1K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1021 R1022 R1023 R1024 R1025 1-216-065-91 1-216-659-11 1-216-659-11 1-216-681-11 1-216-025-91 RES,CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 4.7K 2.2K 2.2K 18K 100 5% 0.5% 0.5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1026 R1027 R1028 R1029 R1030 1-216-109-00 1-216-659-11 1-216-647-11 1-216-025-91 1-216-025-91 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 330K 2.2K 680 100 100 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1031 R1032 R1033 R1034 R1035 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1036 R1037 R1038 R1039 R1040 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1041 R1042 R1043 R1044 R1045 1-216-025-91 1-216-025-91 1-216-025-91 1-216-667-11 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP METAL CHIP RES,CHIP 100 100 100 4.7K 4.7K 5% 5% 5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1047 R1049 R1050 R1051 R1052 1-216-073-00 1-216-065-91 1-216-073-00 1-216-097-91 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 4.7K 10K 100K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1053 R1054 R1055 R1056 R1057 1-216-049-91 1-216-073-00 1-216-049-91 1-216-073-00 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 10K 1K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1058 R1059 R1061 R1062 R1063 1-216-073-00 1-216-049-91 1-216-073-00 1-216-049-91 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 1K 10K 1K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1064 1-216-049-91 RES,CHIP R1065 1-216-125-00 RES,CHIP 1K 1.5M 5% 5% 1/10W 1/10W REF.NO. PART NO. 7-15 N DESCRIPTION REMARK R1066 1-216-073-00 RES,CHIP R1067 1-216-057-00 RES,CHIP R1068 1-216-057-00 RES,CHIP 10K 2.2K 2.2K 5% 5% 5% 1/10W 1/10W 1/10W R1069 R1070 R1071 R5003 R5005 1-216-049-91 1-216-057-00 1-216-081-00 1-216-295-91 1-216-081-00 RES,CHIP RES,CHIP RES,CHIP SHORT RES,CHIP 1K 2.2K 22K 0 22K 5% 5% 5% 1/10W 1/10W 1/10W 5% 1/10W R5006 R5007 R5010 R5011 R5015 1-216-073-00 1-216-049-91 1-216-295-91 1-216-073-00 1-216-049-91 RES,CHIP RES,CHIP SHORT RES,CHIP RES,CHIP 10K 1K 0 10K 1K 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R5108 R5109 R5110 R5113 R5115 1-216-308-00 1-216-308-00 1-216-073-00 1-216-073-00 1-215-859-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL OXIDE 4.7 4.7 10K 10K 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1W F R5116 R5119 R5122 R5205 R5206 1-216-073-00 1-216-073-00 1-215-859-00 1-216-073-00 1-215-859-00 RES,CHIP RES,CHIP METAL OXIDE RES,CHIP METAL OXIDE 10K 10K 22 10K 22 5% 5% 5% 5% 5% 1/10W 1/10W 1W F 1/10W 1W F R5207 R5208 R5209 R5308 R5309 1-216-073-00 1-216-069-00 1-216-308-00 1-216-308-00 1-216-308-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 6.8K 4.7 4.7 4.7 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R5310 R5313 R5315 R5316 R5319 1-216-073-00 1-216-073-00 1-215-859-00 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP METAL OXIDE RES,CHIP RES,CHIP 10K 10K 22 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1W F 1/10W 1/10W R5322 R5406 R5407 R5408 R5409 1-215-859-00 1-216-083-00 1-216-085-00 1-216-308-00 1-216-308-00 METAL OXIDE RES,CHIP RES,CHIP RES,CHIP RES,CHIP 22 27K 33K 4.7 4.7 5% 5% 5% 5% 5% 1W F 1/10W 1/10W 1/10W 1/10W R5410 R5413 R5415 R5416 R5419 1-216-081-00 1-216-097-91 1-215-887-00 1-216-081-00 1-216-097-91 RES,CHIP RES,CHIP METAL OXIDE RES,CHIP RES,CHIP 22K 100K 150 22K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 2W F 1/10W 1/10W R5422 R5502 R5503 R5504 R5505 1-216-451-11 1-216-081-00 1-216-081-00 1-216-089-91 1-216-089-91 METAL OXIDE RES,CHIP RES,CHIP RES,CHIP RES,CHIP 120 22K 22K 47K 47K 5% 5% 5% 5% 5% 2W F 1/10W 1/10W 1/10W 1/10W R5506 R5507 R5508 R5509 R5510 1-216-069-00 1-249-382-11 1-249-382-11 1-249-382-11 1-249-382-11 RES,CHIP CARBON CARBON CARBON CARBON 6.8K 1.2 1.2 1.2 1.2 5% 5% 5% 5% 5% 1/10W 1/4W F 1/4W F 1/4W F 1/4W F R5602 1-216-081-00 RES,CHIP R5603 1-216-077-91 RES,CHIP R5604 1-216-081-00 RES,CHIP 22K 15K 22K 5% 5% 5% 1/10W 1/10W 1/10W CPD-E500/E500E N DESCRIPTION REMARK R5605 1-216-097-91 RES,CHIP 100K R5607 1-215-862-11 METAL OXIDE 68 5% 5% 1/10W 1W F R5610 1-216-308-00 RES,CHIP 5% 1/10W 4.7 CPD-E500/E500E REF.NO. PART NO. <CRYSTAL> X001 1-760-682-21 VIBRATOR, CRYSTAL (24.756MHz) 9-978-667-01 1999LL05253-1 Sony Corporation 9-978-667-01 Computer Display Company Computer Display DIV. – 80 – English 1999LL05253-1 Printed in Japan 1999.12