Download Hoist Push-Button Switches

Transcript
Hoist Push-Button Switches
COB 80 series
For Indirect Operation of Electrical Machinery
(4/5)
Product name/
appearance
Pilot lamp
Power
Switches
type
General
mass (g)
UN 80 G■
UN 80 GD■
UN 80 GD24BC
UN 80 GD12BC
20
20
20
20
Electromagnetic buzzer UN 80Z□
50
Hoist Push-Button
Switches
UN 80V
50
Plug for spare hole UN 80H
10
Volume
Rating
Memo
・This lamp is installed in a switch unit hole.
・UN 80 G■ (Neon lamp) Note 1
・UN 80 GD■ (LED lamp) Note 1
・6V/48V DC and 24V/48V AC can also be produced.
・M4 screws (pressure terminal type) and soldered terminals can also be produced.
・Insulation resistance: 100 MΩ or more (500 V DC Megger)
・Withstand voltage: 1500 V AC / minute
・Marked on the positive (+) side of the LED lamp.
・Two button holes are needed for installation.
・This is a loud alert buzzer.
・M4 screws (pressure terminal type)
・Appearance from the case surface is
same as UN 80H. (Photo of appearance
・Insulation resistance: 100 MΩ or more (500 V DC Megger)
・Withstand voltage: 1000 V AC / minute
on rear.)
・Variable resister: RV24YN, knob attachment (Please ・Aluminum faceplate is prepared.
specify rating.) Note 2
・Degree of protection is IP53.
・Soldered terminal
・Insulation resistance: 100 MΩ or more (500 V DC Megger)
・Withstand voltage: 500 V AC / minute
・This rubber cover also improves the
・Packing for spare hole: Black rubber
appearance.
・Packing holder: Steel plate
Operating Push
Button Switches
Remarks :
1. Specification code for rated voltage must be entered on □ at the end of each type.
2. Specification code for lamp voltage and color in ■ at the end of each type.
Product name/
appearance
type
Alert buzzer switch UN L
Rating
General
mass (g)
Hole sizeφ12
Foot
Switches
40
40
40
40
Pilot lamp
LNR 082B■
LER 082B■
LER 082B24BC
LER 082B12BC
30
30
30
30
A
・Cannot be installed on
COB 81 or 82.
・There are no size φ12 or
φ19 holes in the cases if
neither an alert buzzer
switch nor pilot lamp is
specified for COB 83 to 86
and COB 803 to 807.
Withstand voltage 2000 V AC
・LNR 103B■,
LNR 082B■
(Neon lamp) Note 1
・LER 103B■,
LER 082B■
(LED lamp) Note 1
6V DC can also be produced.
・Soldered terminal
LAR
M
Hole sizeφ19
LNR 103B■
LER 103B■
LER 103B24BC
LER 103B12BC
Memo
・Soldered terminal
・Standard button character is 警 .
・Rated insulation voltage AC250V
・Installation position: Hole size φ19
Rated thermal current 5A
・The following button markings are also
Rated operating voltage AC220V
available.
Rated operating current 3A
(Inductive load AC12)
(ALARM)
ブ B
Insulation resistance 100MΩ
10
Pilot lamp
(5/5)
(Plain)
・Installation position: Hole size φ19
・Installation position: Hole size φ12
Caution : Cannot be installed on cases with
dual cabling.
Remark : Specification code for lamp voltage and color in ■ at the end of each type.
Note 1 : Rating for electromagnetic buzzer and pilot lamp is as follows.
Liquid Level
Relays
■ Electromagnetic buzzer rating
Rated voltage
Type
UN 80Z24
24V AC
UN 80Z100
100V AC
200V AC
UN 80Z200
■ Pilot lamp rating
Type
2R
UN 80 G
1R
LNR 103B
2G
LNR 082B
(Neon lamp) 1G
2O
1O
2W
1W
Rated voltage Color
200V AC
Red
100V AC
200V AC
Green
100V AC
200V AC
Orange
100V AC
200V AC
White
100V AC
Type
UN 80 GD
LER 103B
LER 082B
(LED lamp)
24R
12R
24G
12G
24O
12O
24W
12W
24BC
12BC
Rated voltage Color
Red
24V DC
12V DC
24V DC
Green
12V DC
24V DC
Orange
12V DC
24V DC
White
12V DC
24V DC
Blue
12V DC
Caution : When lead wire is soldered to the pilot lamp of the soldered terminal, solder the lead wire outputting to the terminal from inside of the
main unit at the same time.
35