Download Hoist Push-Button Switches

Transcript
Hoist Push-Button Switches
COB 80 series
For Indirect Operation of Electrical Machinery
Note 2 : Variable resister rating
・Standard product: RV24YN (Carbon mixed variable resister) ・Specified product: RA25Y (Wire wound variable resister)
Resistance law: B
Resistance law: B
Resistance value Rated current Resistance value Rated current
10Ω
1.2W
1kΩ
1.2W
20Ω
1.2W
2kΩ
1.2W
50Ω
1.2W
5kΩ
1.2W
100Ω
1.2W
10kΩ
1.2W
200Ω
1.2W
500Ω
1.2W
(Source: Volume maker standard rating list)
Rated current Resistance value Rated current
0.4W
20kΩ
0.25W
0.4W
50kΩ
0.25W
0.4W
100kΩ
0.25W
0.4W
200kΩ
0.25W
0.4W
500kΩ
0.25W
0.3W
1MΩ
0.25W
0.3W
2MΩ
0.25W
0.3W
(Source: Volume maker standard rating list)
L
R
Parallel resister
Ⅴ Button markings, markings sheet
Standard markings (Black characters)
Special markings (Black characters)
切
上
下
東
西
南
北
主
上
主
下
補
上
補
下
高
低
高
上
高
下
低
上
低
下
巻
上
巻
下
両
上
両
下
片
上
片
下
前
後
左
右
起
伏
伸
縮
正
逆
停
開
昇
降
元
先
陸
海
山
柱
早
速
遅
高
速
低
速
閉
非
警
ブ
ザ
電
源
照
明
ON
吸
出
内
外
主
補
連
単
始
点
滅
照
ラ
OFF
UP
DOWN
U
D
EAST
WEST
SOUT
NORT
E
S
ラ
入
ラ
切
ブ
入
ブ
切
商
自
手
自
動
手
動
自
入
自
切
IN
OUT
N
FOR
REV
STOP
F
R
L
1
2
B
U1
D1
U2
D2
A
INV
ブ
水
平
日
上
高
A
B
B
下
高
上
低
下
低
開
閉
停
止
前
進
運
転
切
削
A
(Plain red)
W
スタート 原点
入切
上
昇
下
降
電
入
電
切
照
入
後
退
起
動
照
切
※Characters other than the above can also be produced. Please contact us for details.
Attachment of the marked board
Please attach the marking stickers to the
transparent chip, and use a gem clip, or suchlike to
push and tease out the button packing surface
without damage, and fit the chip into it.
Marking
sticker
Transparent chip
Case
Markings sheet
Markings sheets on which standard characters are set are also available.
COB80No801
COB80No803
入
切
上
下
左
東
西
南
UP
IN
HIGH
RAISE
RIGHT
FWD
FWD
右
DOWN
OUT
LOW
LOWER
LEFT
REV
REV
北
ON
START
OPEN
FAST
NORTH
EAST
OFF
STOP
CLOSE
SLOW
SOUTH
WEST
COB80No802
主
上
主
下
補
上
補
下
電
源
照
明
ブ
ザ
切
COB80No804
東
西
南
北
COB80No805
UP
COMM
DOWN
STOP
Liquid Level
Relays
Button packing
Foot
Switches
入
Operating Push
Button Switches
The following methods should be used to counteract the above.
1. Light does not come on if the voltage is maintained at the same as or lower
than discharge lamp through partial pressure by inserting a parallel resister.
Lower resistance value is more effective, but about 100kΩ/W is sufficient.
2.Light does not come on if the voltage is maintained at the same as or lower
than discharge lamp through partial pressure based on parallel resistance.
100kΩ/W or less is needed.
Hoist Push-Button
Switches
Reference :Erroneous lighting of the neon lamp (half-lighting when switch is turned off)
When the switch is turned off, the neon lamp may appear half lit. The following three causes can be considered.
1. Effect from inductive power within the parallel line
2. Effect from current leaking from the condenser between contacts
3. Effect from current leaking due to reduced insulation between contacts
Power
Switches
Resistance value
50Ω
100Ω
200Ω
500Ω
1kΩ
2kΩ
5kΩ
10kΩ
36