Download Onkyo TX-DS494 Receiver

Before using this unit
3. After batteries are installed and seated correctly,
replace the compartment cover.
Setting the AM tuning step frequency
(Worldwide models only)
Worldwide models are equipped with a switch that controls the
AM band tuning steps. Please set this switch to match the AM
band tuning step frequency in your area.
U.S.A. and Canada: 10 kHz
Other areas: 9 kHz
AM FREQUENCY
STEP
10 k Hz
9 k Hz
SUB
WOOFER
PRE OUT
ANTENNA
R
MONITOR
OUT
MONITOR
OUT
IN
FM
75
IN
CENTER
SPEAKER
IN
L
R
OPTICAL
COAXIAL
DVD
CAUTION:
SPEAKER IMPEDANCE
2
1
A
6 OHMS MIN. PER EACH
SPEAKER TERMINAL
AC OUTLETS
SWITCHED
TOTAL 100W MAX.
AV RECEIVER
FRONT
R
IN
AM FREQUENCY
STEP
MODEL NO. TX-DS494
L
RATING: AC 120 / 220 -230 V
50 / 60 Hz 260 W
10 k Hz
9 k Hz
SURR
CD
L
SURROUND
SPEAKERS
REMOTE
CONTROL
IN
GND VIDEO 1
PHONO
L
S VIDEO
IN
DIGITAL INPUT
TAPE
R
VIDEO 2
DVD VIDEO 1
L
OUT
AM
R
OUT
VOLTAGE SELECTOR
L
120 V
220-230 V
B
VIDEO 2
IN
R
CENTER
R
L
VIDEO
SUB
WOOFER
R
MULTI
CHANNEL INPUT
L
FRONT SPEAKERS
Setting the voltage selector (Worldwide models only)
Worldwide models are equipped with a voltage selector to
conform with local power supplies. Be sure to set this switch to
match the voltage of the power supply in your area before
plugging in the unit.
Determine the proper voltage for your area: 220-230 V or 120 V. If
the preset voltage is not correct for your area, insert a screwdriver
into the groove in the switch. Slide the switch all the way to the
right (120 V) or to the left (220-230 V), whichever is appropriate.
SUB
WOOFER
PRE OUT
ANTENNA
R
MONITOR
OUT
MONITOR
OUT
IN
FM
75
IN
COAXIAL
DVD
CENTER
SPEAKER
IN
R
L
OPTICAL
CAUTION:
SPEAKER IMPEDANCE
1
2
A
R
L
R
OUT
TX-DS494
AC OUTLETS
SWITCHED
TOTAL 100W MAX.
MODEL NO. TX-DS494
L
RATING: AC 120 / 220 -230 V
50 / 60 Hz 260 W
SURR
Remote control sensor
SURROUND
SPEAKERS
6 OHMS MIN. PER EACH
SPEAKER TERMINAL
AV RECEIVER
FRONT
IN
CD
Point the remote controller toward the remote control sensor. The
STANDBY indicator lights up when the unit receives a signal
from the remote controller.
REMOTE
CONTROL
IN
GND VIDEO 1
PHONO
Using the remote controller
STANDBY indicator
L
S VIDEO
IN
DIGITAL INPUT
TAPE
R
VIDEO 2
DVD VIDEO 1
L
OUT
AM
Notes:
• Do not mix new batteries with old batteries or different kinds
of batteries.
• To avoid corrosion, remove the batteries if the remote
controller is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both batteries at the same time.
• The life of the batteries supplied is about six months but this
will vary depending on usage.
AM FREQUENCY
STEP
10 k Hz
9 k Hz
VOLTAGE SELECTOR
L
220-230 V
B
VIDEO 2
120 V
IN
R
CENTER
R
L
VIDEO
SUB
WOOFER
MULTI
CHANNEL INPUT
R
30°
L
FRONT SPEAKERS
30°
VOLTAGE SELECTOR
220-230 V
Approx. 5 meters
(16 feet)
120 V
Installing batteries into the remote controller
1. Remove the battery compartment cover by
pressing and sliding the cover.
2. Insert two AA (R6 or UM-3) batteries into the
battery compartment. Carefully follow the
polarity diagram (positive (+) and negative (–)
symbols) inside the battery compartment.
Notes:
• Place the unit away from strong light such as direct sunlight or
inverted fluorescent light which can prevent proper operation
of the remote controller.
• Using another remote controller of the same type in the same
room or using the unit near equipment which uses infrared rays
may cause operational interference.
• Do not put objects on the remote controller. Its buttons may be
pressed by mistake and drain the batteries.
• Make sure the audio rack doors do not have colored glass.
Placing the unit behind such doors may prevent proper remote
controller operation.
• If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.
5