Download GE Profile JT980 Electric Double Oven

Installation
Instructions
30” Built-In Trivection™
Wall Oven
JT930, JT980, ZET3038, ZET3058
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com
BEFORE YOU BEGIN
FOR YOUR SAFETY:
Read these instructions completely
and carefully.
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F) generated
by the oven.
•
IMPORTANT
•
IMPORTANT
•
•
•
•
•
•
— Save these
instructions for local inspector’s use.
— Observe all
governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these
instructions for future reference.
Skill level – Installation of this appliance
requires basic mechanical and advanced
electrical skills.
Completion time – 1 to 3 hours
Proper installation is the responsibility of
the installer.
Product failure due to improper installation
is not covered under the Warranty.
WARNING:
The electrical power to
the oven supply line must be shut off while
line connections are being made. Failure to
do so could result in serious injury or death.
• To prevent damage to the door and to
prevent excessive microwave leakage, do
NOT remove the door on the single wall
oven or the upper oven door on the double
wall oven.
WARNING
— This appliance must
be properly grounded.
•
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT
permitted on these products.
229C4053P546-2
31-10557-2
04-04 JR
1
Installation Instructions
PREPARE TO INSTALL THE OVEN
TOOLS YOU WILL NEED
PARTS INCLUDED
Metal
Bottom Trim
Drill with 1/8” Bit
(Extension may be
required)
Safety Glasses
12 Screws
Plastic
Bottom Trim
Straight Edge or
Square
Adjustable Wrench
(for 1-7/16” Nut)
OR
Pencil
Phillips Screwdriver
Metal Bottom
Trim Assembly
Level
Tape Measure
Gloves
Hand or Sabre Saw
MATERIALS YOU MAY NEED
Strain Relief
Clamp for 1/2”
conduit
Junction Box
Wire Nuts
60” of String for Single Ovens
96” of String for Double Ovens
2
Installation Instructions
1 PRE-INSTALLATION
1 PRE-INSTALLATION (CONT.)
All installation information on the following
pages is to be used for SINGLE and DOUBLE
oven installation!
A
NOTE: To prevent damage to the door and
to prevent excessive microwave leakage, do
NOT remove the door on single wall oven
models or the upper oven door on double
wall oven models.
Remove packaging materials. Check
behind hinges. Remove plastic on trims
and panel, all tape around the oven and
any shipping screws securing the oven
to the base pad. Use caution when lifting
the oven forward; the ovens are front
heavy.
E
The lower oven door on the double
wall oven may be removed as an added
convenience during installation.
See Step 4.
DO NOT LIFT THE OVEN BY THE HANDLE!
Oven Racks
EASY
INSTA
LLAT
EASY INSTALLATION
OF
IONYOUR NEW
30"
OF
WAOVEN
30" WALL
LL OV YOUR
NEW
EN
Broiler Pan
and Grid
Befo
re
IMPO you begin
-Read
IMPO RTANTSave
these
Note RTANTto Insta OBSE these instruinstru
OWN
ction
Before
you
begin-Read
completely
RVE instructions
ller- these
ERs compand carefully.
ALL ctions
Be instructions
Note
Keep
IMPORTANTfor local inspector’s use.
- ThisSave these
these sure to GOVERNIfor local letely
and
leave
appli
inspe
IMPORTANT- OBSERVE
ALL GOVERNING
CODES AND
ORDIANCES.
ance instruction these NG COD
ctor’s carefully.
Note to Installer- Be suremust
to leave these
with
the consumer.
instru ES
s forinstructions
use.
AND
be prop
ction
futur
OWNER- Keep these instructions
for future
reference.
e refer s withORDIANC
erly
FOR
grou
Note- This
appliance must be properly grounded
(if ence
applicable).
ES.
the
YOUR
nded
cons
.
SAFE
umer
(if appli
Befo
TY
.
re
cable
instru you begin
).
-Read
caref ctions
comp
ully.
ELECTRICAL REQUIREMENTS
IMPO FOR YOUR SAFETY
letely these
and
ELEC
instru RTANTTRIC
Save
ction you begin-Read these
IMPOBefore
AL REQU these
Before you begin-Read
these
RTAN s for local
Befo
completely and
GOV instructions
instructions
completely
and
IREM
re
ERNI T- OBSE inspe
instru you begin
ENTS
Note carefully.
ctor’s
NG
carefully.
RVE
-Read
caref ctions
use.
ALL
IMPORTANTSave these
Insta CODES
these to
compSave these
IMPORTANTully.
AND
llerIMPO
instru
letely these
for local inspector’s use.
OWN instructions
instructions for localand
inspector’s use.
ction Be sure ORDIANC
ERinstru RTANTto leave
OBSERVE
ALL ES.
for futur IMPORTANTKeep s with
Save OBSERVE ALL
IMPORTANTthe AND ORDIANCES. IMPO ction
these CODES
these
s for
eGOVERNING
Note
refer
GOVERNING
instru cons
localCODES AND ORDIANCES.
umer
ence
GOV RTAN
Tprop ThisNote
to
Installer- Be
sure to leave
ction
inspe
ERNI
.
Note toOBSE
InstallerBe ctor’s
sure to leave
erly appliance.
s
Note
NG
RVE
grou
these instructions
with the consumer.
Befo
these COD
instructions
with theuse.
consumer.
nded must
re
these to Insta
ES ANDALL
be
ller- Keep
instru youOWNERKeep
begin (if
OWNERinstructions
applithese instructions
Be surethese
OWN instru
ORD
cable
-Read
caref ctionsfor future
reference.
IANC
ER- forction
future
reference.
comp
to leave
s with
).
for futur Keep
ully.
these
ES.
IMPO
letelyappliance
Note- This
must be
the
Note-these
This appliance
e refer
Note
consmust be
and
instru
instru RTANT-properly grounded
(if applicable). prop - This properly
umer
ence grounded
(if applicable).
Save
ction
.
.
IMPO ctions Beforethese
erly appli
s these
anceyou begin-Read
for local you begin-Read these
grouBefore
Befo
GOV RTANT- instructions
nded must
re
instructions
and
ERNI
OBSE inspe completely and
be
instru you begin
(if applicompletely
Note
ctor’s
NG carefully.
COD RVE ALL
-Read
cable
caref ctions carefully.
use.
these to Insta
comp
ES
ully.
).
Save these
AND
ller-IMPORTANTIMPO
IMPORTANTSave these
letely these
OWN instruction Be sure ORD
andfor local inspector’s use.
instructions forIANC
local inspector’s instru
use. RTAN
ERinstructions
T- Save
to leave
for futur Keep s with
ES. ALL
IMPORTANTOBSERVE
IMPO ctions
the
IMPORTANTOBSERVE ALL
these
e refer these
Note
for local
instru consCODES
GOVERNING
GOV RTANTumer AND ORDIANCES.
GOVERNING CODES AND ORDIANCES.
prop This applience.
ction
ERNI
OBSE inspe
erly
Note to InstallerNote
ctor’s Be sure to leave
s Be. sure to leave
NG
to InstallerRVE
grou ance must
CODNote
use.
ALL
nded these instructions with the consumer.
these to Insta
ES AND
instructions with the consumer.
ller- these
(if appli be
OWN instruction BeOWNEROWNERKeep these instructions
Keep
these instructions
sure ORD
cable
IANC
ERto leave
for futur Keep s with
).
for future reference.
ES.
for future
reference.
the
these
e
Note
cons
refer
Note- This appliance must be
Noteappliance
must be
instruThis
umer
prop This applience.
ction
properly grounded (if applicable).
. (if applicable).
properly
grounded
erly
s
grou ance must
nded
(if appli be
cable
).
Literature
Pack
B
Open oven door and remove literature
pack, broiler pan and grid and oven
racks.
C
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
D
Be sure to place all literature, Owner’s
Manual, Installation Instructions, etc.
in a safe place for future reference.
3
F
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 225 lbs. single, 375 lbs.
double.)
G
Remove the bottom trim from the top
of the oven. It will be installed at the end
of the installation process.
Installation Instructions
SINGLE BUILT-IN OVEN CUTOUT OPTIONS
2 CUTOUT OPTIONS FOR SINGLE
BUILT-IN OVENS
A
NOTE: If the cabinet does not have a front
frame and the sides are less than 3/4” thick,
shim both sides equally to establish the
cutout width.
Skip to Step 3 for Double Built-In Oven models.
There are 4 installation options for single built-in ovens.
Choose the appropriate one for your application:
A
WALL MOUNT—SINGLE BUILT-IN OVEN OPTION
B
WALL MOUNT—SINGLE BUILT-IN OVEN BELOW
AN ADVANTIUM™ OVEN OPTION
C
WALL MOUNT—SINGLE BUILT-IN OVEN ABOVE
A WARMING DRAWER OPTION
D
UNDER COUNTER—SINGLE BUILT-IN OVEN
OPTION
A
WALL MOUNT—SINGLE BUILT-IN OVEN
OPTION
3 1/2”
Cutout Width
28 1/2” Min
28 5/8” Max.
All corners must
be cut square
Allow 11/16”
on sides for
overlap of oven
beyond cutout
If the cabinet does not have a solid bottom,
two braces or runners must be installed level
with the bottom of the cutout to support the
weight of the oven. For single ovens, the
runners and braces must support 225 lbs.
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.
CL
7”
Required Junction
Box Area
Opening
between
inside walls
must be at
Least 28 1/2”
Wide
Suitable
Bracing to
Support
Runners
21 5/8”
Over Centerline
of Cabinet
6”
Cutout Height
27 1/4” Min.
27 5/16” Max.
NOTE: This oven is not approved for
stackable or side by side installation.
12”
21”
Allow a minimum of
21” for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
Cabinet Width
Recommended
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
Allow 1” minimum
at top and 1 1/4”
minimum at bottom
for overlap of oven
beyond cutout
Recommended
cutout location
from floor
32 1/2”
Cabinet
Width 30”
30”
32
23
28
28
27
27
WALL MOUNT—SINGLE BUILT-IN OVEN
OPTION (CONT.)
1/2”
1/2” Min.
1/2” Min.
5/8” Max.
1/4” Min.
5/16” Max.
4
2” x 4” or
equivalent
runners
level with
bottom of
cutout
Installation Instructions
B
WALL MOUNT—SINGLE BUILT-IN OVEN
BELOW AN ADVANTIUM OVEN OPTION
30”
C
24”
Min.
Advantium
cutout
WALL MOUNT—SINGLE BUILT-IN OVEN
ABOVE A WARMING DRAWER OPTION
23 1/2” Min.
inside
Construct
solid bottom
min. 3/8”
plywood
supported
by 2 x 4 or
1 x 2 runners,
all four sides
Construct
solid bottom
min. 3/8”
plywood
Oven
cutout
2” Min.
2” Min.
Oven
cutout
Warming
drawer cutout
A
• When installed over a single wall oven,
allow at least 2” between the two openings.
This separation will provide clearance for
bottom overlap of the Advantium oven and
top overlap of the single wall oven.
• If you are replacing a GE/Monogram electric
double oven with the combined installation
of an Advantium and single wall oven, the
middle rail separating the two openings
may need to be larger than the 2” min.
shown.
• Always maintain 36 3/4” min. distance from
the floor to the Advantium oven cutout in
any installation combination.
• When installed in combination with a
GE/Monogram single wall oven, use
separate electrical junction boxes.
• Refer to Advantium oven installation
instructions for electrical requirements and
installation details of that product.
• Advantium ovens are approved for
installation above only certain specified
wall oven models. See the label attached
to the top of the oven for approved
Advantium oven models.
Bottom of warming drawer must be 1”
above toekick
• A 2” min. clearance between oven and
warming drawer cutouts is required.
• Additional clearance may be required if
2 x 4 blocks are used to support the solid
floor of the oven above. Check to be sure
that oven supports above the Warming
Drawer location do not obstruct the
required interior depth and height.
• Refer to warming drawer installation
instructions for electrical requirements and
installation details of that product.
• Warming drawers are approved for
installation below only certain specified
wall oven models. See the label attached to
the top of the oven for approved warming
drawer models.
5
NOTE: A single wall oven can be installed in
combination with the Advantium oven above
and a warming drawer below as long as the
dimensions and information on this page are
applied to the combination installation.
Installation Instructions
SINGLE BUILT-IN OVEN CUTOUT OPTIONS
D
(CONT.)
UNDER COUNTER—SINGLE BUILT-IN OVEN OPTION
3 1/2”
7”
25”
Required Junction
Box Area
Top and/or side fillers
may be necessary if unit
is positioned between
existing cabinets. Be
sure they are attached
securely, since they will
anchor the oven in the
cabinet.
28 1/2” Min.
28 5/8” Max.
Allow 1” at top,
1 1/4” at bottom
and 11/16” at
sides for overlap
of oven beyond
cutout
27 1/4” Min.
27 5/16” Max.
6”
36” Typical
Countertop
Height
12”
24”
3/4”
Support Platform
Required
5 9/16”
Reference dimension for
maximum support height with
typical 36” countertop height
Must Support 225 lbs.
NOTE: This oven is not approved to be installed under a cooktop.
6
Installation Instructions
DOUBLE BUILT-IN OVEN CUTOUT
3 CUTOUT FOR DOUBLE BUILT-IN
OVEN
Cutout Width
28 1/2” Min
28 5/8” Max.
3 CUTOUT FOR DOUBLE BUILT-IN
OVEN (CONT.)
If the cabinet does not have a solid bottom,
two braces or runners must be installed level
with the bottom of the cutout to support the
weight of the oven. For double ovens, the
runners and braces must support 375 lbs.
7” from side cutout
All corners
must be cut
square
Allow 11/16”
on sides for
overlap of oven
beyond cutout
Allow a
minimum
of 21” for
clearance
to adjacent
corners,
drawers,
walls, etc.
when door
is open
Opening
between
inside
walls must
be at Least
28 1/2”
Wide
Allow 1”
minimum at
top and 1 1/4”
minimum at
bottom for
overlap of oven
beyond cutout
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.
Required
Junction
Box Area
CL
7”
Cutout Height
51 13/16” Min.
51 15/16” Max.
25”
Suitable
Bracing to
Support
Runners
21”
21 5/8”
Over Centerline
of Cabinet
Recommended
cutout location
from floor 12”
Cabinet
Width 30”
Cabinet Width
30”
Recommended
Cutout Location
from Floor
12”
Cutout Depth
23 1/2” Min.
Cutout Width
28 1/2” Min.
28 5/8” Max.
Cutout Height
51 13/16” Min.
51 15/16” Max.
NOTE: If the cabinet does not have a front
frame and the sides are less than 3/4” thick,
shim both sides equally to establish the
cutout width.
7
2” x 4” or
equivalent
runners
level with
bottom of
cutout
Installation Instructions
REMOVE THE LOWER OVEN DOOR
ON DOUBLE WALL OVEN MODELS ONLY
To prevent damage
to the door and to
prevent excessive
microwave exposure,
do NOT remove the door on the
single wall oven or the upper oven
door on the double wall oven.
4 ON DOUBLE WALL OVEN
MODELS, REMOVE THE LOWER
DOOR ONLY (CONT.)
D
NOTE: The oven door is heavy. You may need
help lifting the door high enough to slide it
into the hinge slots. Do not lift the door by
the handle.
Close door to the door removal position,
which is halfway between the broil stop
position and fully closed.
4 ON DOUBLE WALL OVEN
MODELS, REMOVE THE LOWER
DOOR ONLY:
A
Fully open the door.
B
Pull the hinge locks down toward the
door frame, to the unlocked position.
A tool, such as a small flat-blade
screwdriver, may be required.
Removal position
E
Slot
Hinge lock
Pull hinge locks down to unlock
C
Firmly grasp both sides of the door at
the top.
8
Lift door up and out until the hinge arm
is clear of the slot.
Installation Instructions
ELECTRICAL CONNECTIONS
ELECTRICAL REQUIREMENTS
ATTENTION INSTALLER
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
(Rating Plate is located on oven frame.)
All electric wall ovens must be hard wired
(direct wired) into an approved junction box.
A plug and receptacle is NOT permitted on
these products.
DO NOT shorten the flexible conduit. The
conduit strain relief clamp must be securely
attached to the junction box and the flexible
conduit must be securely attached to the
clamp. If the flexible conduit will not fit within
the clamp, do not install the oven until a
clamp of the proper size is obtained.
We recommend you have the electrical wiring
and hookup of your oven connected by a
qualified electrician. After installation, have
the electrician show you where your main
oven disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your oven according to governing codes
could result in a hazardous condition. If there
are no local codes, your oven must be wired
and fused to meet the requirements of the
National Electrical Code, ANSI/NFPA No.
70 – Latest Edition. You can get a copy by
writing:
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are UL
recognized for connection to heavier gauge
household wiring. The insulation of these 3
leads is rated at temperatures much higher
than the temperature rating of household
wiring. The current carrying capacity of the
conductor is governed by the wire gauge and
the temperature rating of the insulation
around the wire.
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
WARNING:
Improper connection
of aluminum house wiring to copper leads
can result in an electrical hazard or fire. Use
only connectors designed for joining copper
to aluminum and follow the manufacturer’s
recommended procedure closely.
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a four-conductor
connection to an electric oven. When
installing an electric oven in new
construction, a mobile home, recreational
vehicle or an area where local codes prohibit
grounding through the neutral conductor,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR-CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase
A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors
approved for use with aluminum wiring
must be used.
9
Installation Instructions
ELECTRICAL CONNECTIONS
(CONT.)
5 TURN OFF ELECTRICITY
7 NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH
CIRCUIT CONNECTION
Turn off the circuit breaker or remove fuses to
the oven branch circuit.
•
•
•
•
When installing in new construction, or
When installing in a mobile home, or
When installing in a recreational vehicle, or
When local codes do not permit grounding
through neutral:
A Cut the neutral (white) lead from the
crimp. Re-strip the neutral (white) lead to
expose the proper length of conductor.
6 CONNECT CONDUIT
With the oven supported on a table or
platform in front of the cabinet opening,
connect the flexible conduit to the electrical
junction box as shown below. Position the
conduit in such a manner that it will lie
behind the oven in a natural loop when the
oven is installed. You will need to purchase
an appropriate strain relief clamp to complete
the connection of the conduit to the
junction box.
Ground Wire
Junction Box Location
Conduit
Ground
Wire
Bare
Ground
Junction Box Cover
B
Attach the appliance grounding lead
(green or bare copper) in accordance
with local codes. If the residence
grounding conductor is aluminum,
see WARNING under ATTENTION
INSTALLER.
C
Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray)
in accordance with local codes, using a
wire nut.
D
Connect the oven red lead to the branch
circuit red lead and the oven black lead
to the branch circuit black lead in
accordance with local codes, using
wire nuts. If the residence red, black or
white leads are aluminum conductors,
see WARNING under ATTENTION
INSTALLER.
E
Install Junction Box Cover.
Red
White
Black
Place oven on a
support to assist in
connecting conduit
Strain Relief Clamp
(not included) must be
used at Junction Box
10
Installation Instructions
8 THREE-CONDUCTOR BRANCH
CIRCUIT CONNECTION
When connecting to a three-conductor branch
circuit, if local codes permit:
A Connect the bare oven ground conductor
with the crimped neutral (white) lead to
the branch circuit neutral (white or gray
in color), using a wire nut.
Ground and
Neutral Wires
Junction Box Cover
B
Connect the oven red lead to the branch
circuit red lead in accordance with local
codes, using a wire nut.
C
Connect the oven black lead to the
branch circuit black lead in accordance
with local codes, using a wire nut. If the
residence red, black or white leads are
aluminum conductors, see WARNING
under ATTENTION INSTALLER.
D
Install Junction Box Cover.
11
Installation Instructions
SECURE THE OVEN IN THE OPENING
9 SLIDE THE OVEN INTO THE
OPENING
A
10 DRILL THE PILOT HOLES AND
MOUNT THE OVEN
Loop (do not tie) the correct length of
string around the conduit before the
oven is slid into place. This will keep the
conduit from falling improperly behind
the oven. For the single wall oven, locate
string toward the middle at the bottom
of the oven. For the double wall oven,
locate string toward the right side at the
bottom of the oven.
NOTE: Before drilling the pilot holes, make
sure the oven is pushed as far back into the
opening as it will go, is level and is centered.
A
Pull out on
string loop
while pushing
the oven into
the cabinet
B
Mounting
Hole
Locations
On a single wall oven, lift the oven into
cabinet cutout using the bottom of the
oven and the bottom of the door as a
grip. Carefully push against the front
edges of the door. On a double wall
oven, lift the oven into cabinet cutout
using the lower oven opening as a grip.
Carefully push against oven front frame.
Do not push against outside edges.
C
As you slide the oven back, pull the
string so that the conduit will lie behind
the oven in a natural loop.
D
Once the oven is in the cutout, place the
level on an oven rack inside the oven
to make sure the oven is level from front
to back and from side to side. Use shims
as required.
Drill six 1/8” pilot holes through the
mounting holes (top and bottom) of the
side trim, for the #8 screws provided.
Drill ten holes for the Double Oven.
The screws must
be a minimum of
1/4” from the front
of the cutout. (Door
not shown in this
view.)
WARNING:
Mounting screws must
be used. Failure to do so could result in the
oven falling out of the cabinet, causing
serious injury.
B
Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 3/4” particle board screws.
These may be purchased at any hardware
store.
NOTE: If marks, blemishes or the cutout
opening are visible above the installed oven,
it may be necessary to add wood shims
under the runners and front trim until the
marks or opening are covered.
Once the oven is level and all the way in the
opening, remove the string by pulling on one
end of the loop.
12
Installation Instructions
To install a single metal bottom trim assembly (on some models), see Step 11.
To install a metal bottom trim with a plastic bottom trim (on some models), see Steps 11 and 12.
11 INSTALL THE METAL
BOTTOM TRIM
12 INSTALL THE PLASTIC BOTTOM
TRIM (ON SOME MODELS)
A
With oven installed, take the bottom trim
and center it on the bottom front edge of
the cabinet opening.
B
Using the trim as a template, mark the
center of each slot (two total) where the
mounting holes will be drilled.
C
Remove the trim.
D
Drill pilot holes into the center of each
template mark.
E
Place the bottom metal trim over the
pre-drilled mounting holes, making sure
it is centered.
F
A
Make sure flat side is up on the plastic
bottom trim.
B
Find the key slot on the back of the trim.
Key Hole Slot and Wide Flange at Top
C
Using trim screws provided, secure the
bottom trim to the bottom edge of the
cabinet. If a plastic bottom trim is
supplied, proceed to Step 12.
Match the key slot with the rivet on the
bottom of the side trim, and lower the
trim onto the rivet.
Side Trim
Trim Screws
Lower Trim Mounting Rivet on
End of Metal Lower Trim
Side Trim
Metal Lower Trim
D
Push the trim down, at both ends, until it
snaps securely into place.
Single Wall Oven – Door may not be removed.
Side Trim
Trim Screws
Side Trim
Push Trim Down at Both Ends
Until it Snaps Securely Into Place
CAUTION:
Be sure you do not tip
the oven forward during installation or you
may bend the bottom trim. The bottom trim
provides an opening for cooling air to enter
the cabinet. This opening should never be
blocked.
Metal Lower Trim
Double Wall Oven – Lower oven door only may be
removed.
IMPORTANT: If this unit is ever removed from
the cabinet or the oven is ever pulled out for
service, the trim must be removed first or
damage to the trim will occur.
13
Installation Instructions
REPLACE THE LOWER OVEN DOOR
ON DOUBLE WALL OVEN MODELS
13 ON DOUBLE WALL OVEN
MODELS, REPLACE THE LOWER
DOOR:
A
Firmly grasp both sides of the door at
the top.
Hinge arm
Bottom
edge of slot
Indentation
B
With the door at the same angle as the
removal position, seat the indentation of
the hinge arm into the bottom edge of
the hinge slot. The notch in the hinge
arm must be fully seated into the bottom
of the slot.
C
Fully open the door. If the door will not
fully open, the indentation is not seated
correctly in the bottom edge of the slot.
D
Push the hinge locks up against the front
frame of the oven cavity, to the locked
position.
Hinge arm
Hinge lock
Push hinge locks up to lock
E
Close the oven door.
14
Installation Instructions
FINAL CHECKLISTS
14 PRE-TEST CHECKLIST
15 OPERATION CHECKLIST
A
Remove all protective film.
A
B
Check to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Remove all items from the inside of
the oven.
B
Check that conduit is securely connected
to the junction box.
C
Turn on the power to the oven. (Refer
to your Owner’s Manual.) Verify that the
bake and broil functions make the oven
hot. Verify by feeling heat coming off the
elements within 20 seconds.
D
See your Owner’s Manual for
troubleshooting list.
C
Check that the bottom trim is installed
properly (see Steps 11 and 12).
D
Check to be sure the mounting screws
are installed and flush with the side trim
(see Steps 9 and 10).
NOTE TO ELECTRICIAN:
The power leads supplied with this appliance
are UL recognized for connections to larger
gauge household wiring. The insulation of
these leads is rated at temperatures much
higher than the temperature rating of
household wiring. The current carrying
capacity of a conductor is governed by the
wire gauge and also the temperature rating
of the insulation around the wire.
NOTE: ALUMINUM WIRING
A
WARNING: IMPROPER
CONNECTION OF ALUMINUM HOUSE
WIRING TO THE COPPER LEADS CAN
RESULT IN AN ELECTRICAL HAZARD
OR FIRE.
B
Splice copper wires to aluminum wiring
using special connectors designed and
UL approved for joining copper to
aluminum, and follow the manufacturer’s
recommended connector procedure
closely.
NOTE: Wire used, location and enclosure
of splices, etc., must conform to good
wiring practice and local codes.
15
16
Printed in the United States