Download GE JBP90 Electric Kitchen Range

Installation
Instructions
Self Cleaning Free-Standing
Electric Range
EER2000, EER3000, EER3001, EER3002, JBP10, JBP24, JBP26, JBP30,
JBP35, JBP48, JBP64, JBP66, JBP68, JBP69, JBP71, JBP78, JBP80,
JBP82, JBP90, JBP91, JBP95, JB500, JB600, JB700, JB800
“If you have questions, Call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
Skill Level: High
Average
Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See the Owners Manual for warranty
information.
CAUTION: Before you begin
Read these instructions carefully and
completely.
• IMPORTANT- Save these instructions for
local inspector’s use.
• IMPORTANT- Observe all governing codes
and ordinances.
Parts Included
• NOTE TO INSTALLER- Be sure to leave
these instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• WARNING- This appliance must be
properly grounded.
Materials Needed
Lag Bolts Anchor Sleeves
(For Concrete Floors Only)
( UL Approved 40 AMP)
4- Wire Cord OR 3 -Wire Cord
4’long
4’long
Anti-Tip Bracket and leg leveler
Tools You Will Need
1/4”Nut
driver
Adjustable wrench
Level
Pub. No. 31-10513
229C4053P493
;yy;
y;
Pencil
Safety
Glasses
4
5/16” Hex Head
Nut driver
1
2
1
Tape Measure
Drill with
1/8” Bit
Phillips
Screwdriver
3
Flat-Bladed
Screwdriver
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
WARNING: To reduce the risk of
tipping, the appliance must be
secured by properly installed anti-tip
bracket packed with the appliance.
WARNING: For personal safety
remove house fuse or open circuit
breaker before beginning
installation. Failure to do so could result in
serious injury or even death.
WARNING
All rough-in and spacing dimensions must be met
for safe use of your range. Electricity to the range
can be disconnected at the outlet without moving
the range if the outlet is in the preferred location
(remove lower drawer).
To reduce the risk of burns or fire when reaching
over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet
storage space is to be provided above the
cooktop, the risk can be reduced by installing a
range hood that sticks out at least 5” beyond the
front of the cabinets. Cabinets installed above a
cooktop must be no deeper than 13”.
Be sure your appliance is properly installed and
grounded by a qualified technician.
Make sure the cabinets and wall coverings around
the range can withstand the temperatures (up to
200°F.) generated by the range.
• All ranges can tip
• Injury to persons could result
• Install anti-tip bracket
packed with range
• See Installation Instructions
If you pull the range out and away from the wall
for any reason, make sure the Anti-Tip bracket
is engaged when the range is pushed back
against the wall.
2
Installation Instructions
Pre- Installation Checklist
Move the Range Indoors
Remove Installation Instructions from
literature pack and read it carefully
before you begin. Be sure to place all
literature, Use and Care, Installation
Instruction, etc. in a safe place for
future reference.
Follow directions on the front of the shipping
carton to remove the outer carton and packing
materials.
EASY INSTALLATION OF YOUR NEW
FREE-STANDING RANGE
Before you begin-Read these instructions completely and carefully.
IMPORTANT- Save these instructions for local inspector's use.
IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave these instructions with the consumer.
OWNER- Keep these instructions for future reference.
Note- This appliance must be properly grounded (if applicable).
FOR YOUR SAFETY
ELECTRICAL REQUIREMENTS
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
The shipping base should be removed before
taking the range indoors.
Open the oven door as far
as it will go.
Leave door handle protection on the range
until installation is completed.
Slip appliance dolly
UNDER THE SIDE
when moving the
range indoors. Do
not handle from the
front or rear, damage
will occur.
Push the hinge locks down
toward the door frame, to the
unlocked position. This may
require a flat blade screwdriver.
Preparing the Range
Place hands on both sides of the
door. As you close the door, lift up
and away from the range.
Remove packaging materials. Any packaging
materials must be removed during installation.
This will include adhesive tape, wire ties,
cardboard and protective plastic. Failure to
remove these materials could result in damage
to the appliance once the appliance has been
turned on and surfaces have heated.
DO NOT LIFT THE DOOR
BY THE HANDLE!
Lift door up until the hinges
clear the slots.
Open oven door and remove literature pack,
broiler pan and grid, and oven racks.
Hinge
Clears
Slot
Oven Racks
NOTE: The oven door is very heavy. Be sure you have
a firm grip before lifting the oven door off the hinges.
Use caution once the door is removed. Do not lay the
door on its handle. This could cause dents or scratches.
EASY
INSTAL
LATOF YOUR NEW
EASY
INSTALLATION
ION
30"
Before
OF
WA
IMPOR you begin-30" WALL
OVEN
LL OV YOUR
Read
IMPOR TANTthese
TANT- Save
EN
NEW
Broiler Pan
and Grid
Hinge
Arm
Close the oven door to the
broil stop position.
Protect the kitchen floor! Flatten and place a
piece of the shippiing carton in front of the
installation location to protect the flooring.
Note
these
instru
to Install OBSE
instru
ctions
OWNE
Before
you begin-Read
and carefully.
RVE instructions
ctionscompletely
er- Bethese
compl
ALL
Note- R- Keep
for inspector's
IMPORTANTSave these
instructions
for local
GOVE
sure
etelyuse.
these
This
to leave RNINGlocal inspec and
applia
IMPORTANT- OBSERVE
ALL
GOVERNING
CODES AND ORDIANCES.
instru
carefu
CODE
these
tor's
nce
ctions
Note to Installer- Be suremust
to leave
these instructions
with
the consumer.
S AND
use. lly.
instru
for future
be
ctions
ORDIA
OWNER- Keep these instructionsprope
for future
reference.
with
FOR
NCES
rly grounrefere
the
YOUR
Note- This
appliance must be properly grounded
(if applicable).
nce.
consu .
ded
SAFET
mer.
(if applic
Before
Y
able).
instru you begincarefu ctions complRead
these
ELECTRICAL REQUIREMENTS
lly. YOUR SAFETY
IMPORFOR
etely
and
ELECT
instru TANTRICAL
Before
begin-Read these
ctionsyouSave
Before you begin-Read
IMPOR
these
REQU these
Before
completely and
TANT- for local
IREME
instructions completely
and
GOVEinstructions
instru you beginNTS
RNING OBSE inspector's
carefully.
Note carefully.
RVE
carefu ctions complRead
to Install CODE Save ALL
use.
these IMPORTANTIMPORTANTSave these
these
S ANDthese
lly.
erIMPOR
etely
instru
inspector's use.
Befor localORDIA
OWNE instructions
instructions for local
inspector's use.
and
ctions sure
instru TANTNCES
R-IMPORTANTto leave
OBSERVE
ALL
Save OBSERVE ALL
for future
Keep
with
IMPORTANT.
IMPORctions
the AND ORDIANCES.
these
these CODES
for localCODES
GOVERNING
Noterefere
GOVERNING
AND ORDIANCES.
instru consumer.
GOVE TANTinspec
ctions
tonce.
Installer- Be
sure to leave
prope ThisNote
applia
Note toOBSE
Installer- Be sure
Note RNING
tor's to leave
RVE
Beforerly groun
nce
these instructions
ALL
theseCODE
instructions
with theuse.
consumer.
must with the consumer. these to Install
you
S
ded
instru
AND
be instructions
begin- (if
er- Be
OWNERKeep
these
OWNERKeep these
instructions
applic
ORDIA
OWNE instru
Read
carefu ctionsfor
ctions sure
future
reference.
compl
R- Keep
to leave NCES
theseable).
for futurewith
reference.
for future
IMPOR lly. Note- This
.
etelyappliance must be
the
and
Note-these
This appliance
must be
Noterefere
instru TANTinstru consumer.
properly
grounded (if applicable). prope This properly
nce. grounded
Save
ctions
(if applicable).
applia
IMPORctions for
these
Before
you begin-Read these
Before
Beforerly groun
nceyou begin-Read these
local
TANTGOVE
instructions
inspeccompletely and
instructions
and
ded mustcompletely
instru you beginOBSE
(if applicbe
Note RNING carefully.
tor's
Read
carefully.
carefu ctions compl
CODE RVE ALL
to
use.
able).
these
these Install IMPORTANTSave these
IMPOR lly.
IMPORTANTSave these
etely
er- Be S AND ORDIA
OWNE instructionsinstructions
and
sure
for local inspector'sinstru
use. TANT- instructions
for local inspector's use.
R- Keep
to leave NCES
for future
with
ctions Save
.
IMPORTANTOBSERVE
ALL
IMPOR
these
the
IMPORTANTOBSERVE
ALL
these
for local
Noterefere
instru consu
GOVERNING
CODES AND ORDIANCES.
GOVE TANTGOVERNING
inspec CODES AND ORDIANCES.
OBSE
ctions mer.
prope This appliance.
Note RNING
tor's Be sure to leave
RVE
Note
to Installerrly groun nceNote to Installer- Be sure to leave
CODE
to
use.
ALL
must instructions with the consumer.
these Install
S AND
ded these
instructions with the consumer.
er- these
(if applicbe
OWNE instructionsBeOWNEROWNER- Keep these instructions
sure ORDIA
Keep these instructions
able).
R- Keep
to leave NCES
for future
with
for future reference.
reference. .
the
these for future
consu
Noterefere
Note- This appliance must be
instruThis
Noteappliance must be
ctions mer.
prope This appliance.
properly grounded (if applicable).
rly groun nce properly grounded (if applicable).
ded must be
(if applic
able).
Hinge
Unlocked
Position
Hinge
Slot
Literature
Pack
3
Installation Instructions
A
Installation Required Clearances
See Ilustrations below for all rough-in and spacing
dimensions.
The range may be placed with 0” clearance (flush) at
the back wall and side walls of the cabinet.
**30" MIN
MINIMUM DIMENSIONS BETWEEN
COOKTOP, WALLS, AND ABOVE THE
COOKTOP.
*
**
***
***6"
MIN
**15" MIN
Make sure the wall covering, countertop
and cabinets around the range can withstand the heat (up to 200°F.) generated by
the range.
Allow 30” Minimum clearance between
surface units and bottom of unprotected
wood or metal cabinet, and 15” Minimum
between countertop and adjacent cabinet
bottom.
Recommended spacing to heat sensitive
surfaces.
*0"
*0"
Acceptable electrical
outlet area.
2 1/2"
Orient the electrical
receptacle so the
length is parallel to the floor.
25"
2 1/2"
7 1/2"
36"
30"
NOTE: Use a 4 foot power cord to prevent interference
with the storage drawer. Power cords 4.5 or 6 foot long
may have to be dressed to allow for proper drawer closing.
4
Installation Instructions
B Electrical Connections
Electrical Requirements
B1 Making the Electrical Connection
Remove the wire cover (on the back of the
range) by removing 5 screws using a 1/4” nut
driver. Do not discard these screws.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual properly grounded branch circuit;
protected by a circuit breaker or fuse having
amperage as specified on the rating plate. The
rating plate is located above the storage drawer
on the oven frame.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have the
electrician show you where your main range
disconnect is located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
oven according to governing codes could result in
a hazardous condition. If there are no local
codes, your range must be wired and fused to
meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,
construction utilize a 4 conductor connection to
an electric range. When installing an electric
range in new construction, follow the instructions
in the section on NEW CONSTRUCTION AND
FOUR CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for use
with aluminum wiring must be used.
3
RE
STRAIN
RELIEF
5 Screws to
remove
wire cover
WIRE
COVER
When reinstalling the one-piece wire
cover, make sure that wires do not
become pinched between wire cover
and mainback.
B2
All new constructions, mobile
homes and installations where
local codes do not allow
grounding through neutral.
These will require a four-wire flexible cord kit. If
the range is rated between 8,750 and 16,500
watts, the cord kit must be rated for 40 amps125/250 volts. If the range is rated between
16,501 and 22,500 watts, the cord kit must be
rated for 50 amps-125/250 volts. For existing
construction, a three wire flexible cord kit may
be used, and the same ratings apply as described above.
• When using a cord kit rated 40 Amps, remove
the knockout in the connection plate. You
must use a clamp or strain relief to hold the
cord.
• Terminations must be either closed loop
terminals or open end spade lugs.
• On some models, a filter capacitor may be
connected between the black and white leads
on the junction block.
5
continued on following page
Installation Instructions
B Electrical Connections cont.
NEW CONSTRUCTION AND FOUR
WIRE CORD CONNECTION KIT
B3
Complete 4 wire
cord kit. Below are
step by step
instructions on
how to install the
kit.
Gound
Screw and
Ground Strap
Location
Strain
Relief
Clamp
Remove the screws on
the terminal block with
a 1/4” nut driver or
phillips screwdriver.
Remove
3 screws
Remove the ground
screw using a 5/16”
nut driver, then
remove and discard
the ground strap. Do
not discard the
ground screw, you
will need it later.
Install the four-wire
cord and strain
relief through the
hole in the
connection plate.
Connect the red
and black leads to
the outside
terminals and the
white lead to the
center terminal.
Red or
Black
White
Ground
(Green)
B10 Push the cord upward (to relieve strain),
while tightening the strain relief clamp.
Knockout in center
of connection plate
may be taken out
B7
B9
Ground
Screw
Red or
Black
B5
B6
Attach the green lead
below the junction
block with the ground
screw that was
removed earlier.
3 Screws
Connection
Plate
B4
B8
B11 Re-install the wire cover with the 5
screws removed earlier. Make sure the
wires do not become pinched between
the wire cover and mainback.
Ground
Screw
Ground
Strap
Wire
Cover
4 wire
cord kit
Connection
Plate
Strain
Relief
Clamp
6
Three-wire connection continued on following page
Installation Instructions
B Electrical Connections cont.
Connect the outer wires to the outside
B7a terminals and the center wire to the
center terminal. Do not remove the
ground strap
THREE- WIRE CORD CONNECTION KIT
B3a
Complete 3
wire cord kit.
Below are step
by step
instructions on
how to install
the kit.
Grounded
Neutral
Terminal
(White)
3
Screws
Ground Strap
Ground Screw
Center
Wire
Connection
Plate
B4a Remove the screws on
the terminal block with a
1/4” nut driver or phillips
screwdriver.
Grounded
Neutral
Terminal
(White)
Outer
Wire
Strain
Relief
Clamp
Center
Wire
Remove
3 screws
B8a
Knockout in center
of connection plate
may be taken out
Install the three-wire
cord and strain
relief through the
hole in the
connection plate.
Push the cord upward (to relieve strain),
while tightening the strain relief clamp.
B9a Re-install the wire cover with the 5
screws removed earlier. Make sure the
wires do not become pinched between
the wire cover and mainback.
B5a
B6a
Outer
Wire
3 wire
cord kit
Wire
Cover
Connection
Plate
Strain
Relief
Clamp
Special note: If local codes require an
undgrounded neutral, you must do the
following:
a. Remove ground strap.
b. Fasten the white wire to the center terminal.
c. Use grounding terminal or lead to ground unit
in accordance with local codes.
7
Installation Instructions
C
C1
Installing the Anti-Tip Bracket
Locating The Bracket
C2
The anti-tip bracket, provided with your literature
and broiler pan, must be properly installed to
prevent the range from tipping. Please refer to
the instructions provided with your anti-tip
bracket.
INSTALLATION–WOOD CONSTRUCTION
a. Locate the centers of the four holes identified
in Fig. 1 as Floor-Wood and Wall.
b. Drill a 1/8" pilot hole through the pre-marked
areas. Note the angle of the wall screw in
Fig. 2.
c. Mount the Anti-Tip bracket with the four
screws provided.
a. Decide whether the bracket will be
installed on the right or left side of range
location.
b. If the bracket side of the range has an
adjacent cabinet, place the bracket
against the back wall and cabinet as
shown in Fig. 1. If there is a countertop
overhang, offset the bracket by the
amount of overhang. If there is no
adjacent cabinet, place the bracket to the
outside edge of the range side panel and
back wall.
Adjacent Cabinet
Or Final Location
Of Range Side Panel
Attachment To Wall
Bracket
Wall
Plate
Screw Must
Enter Wood
Or Metal
Fig. 2
INSTALLATION–CONCRETE CONSTRUCTION
Wall
a. For concrete installation you will need two
1/4"x 1-1/2" lag screws, and two sleeve
anchors.
b. Locate the center of the four holes identified
in Fig. 1 as Floor-Concrete and Wall. Drill
the recommended size holes in each.
c. Install the sleeve anchors into the predrilled
concrete holes and install the lag and wall
screws through the Anti-Tip bracket. Make
sure the screws are securely tightened.
Floor-Wood
Bracket
Side
Rear
Leveling
Leg
Installing The Bracket in Wood
or Concrete
Floor-Concrete
Fig. 1
8
Installation Instructions
D
Installing the Range
Storage Drawer Removal
D1
Pull the drawer
out until it stops
D2
Lift the front of
the drawer until
the stops clear
the guide.
D3
Remove the
drawer.
CAUTION: The oven door is heavy.
You may need help lifting the door
high enough to slide it into the
hinges slots. Do not lift the door by
the handle.
Replacing the Oven Door
D9
Stop
Final Check of the Anti-Tip Bracket
D4
Pick the Oven Door up
by placing both hands on
each side. The door is
heavy so you may need
help. Do not lift the door
by the handle.
Place the notch of the
D10 hinge arm into the bottom edge of the hinge
slot.
When installation is
complete and the
range is in place,
inspect to be sure the
rear leveling leg is fully
inserted into the slot of
the Anti-Tip Bracket.
Hinge Arm
Hinge Notch
Open the oven door
D11 as far as it will open.
Level the Range
The range must be level for proper cooking and
baking.
D5 Install the oven racks.(See Owner’s
Manual for instructions.)
Put
a spirit level or a glass SPIRIT
D6
LEVEL
measuring cup partially
filled with water on one of
the oven racks.
D7 Remove the
storage drawer.
The front leveling
legs can be
LEG
LEVELER
accessed from the
RAISE
bottom and the
RANGE
rear legs from the
top.
Bottom Edge
Of Slot
D12
D13
Push the hinge locks
up against the front
frame of the oven
cavity, to the locked
position.
Hinge in
Locked Position
Notch of
Hinge Securely
Fitted into Bottom
of Hinge Slot
Close the oven door.
LOWER
RANGE
D8 Use an adjustable wrench to adjust all four
leg levelers until the range is level.
9
Continued on following page
Installation Instructions
D
Installing the Range cont.
Replacing the Storage Drawer
D13
Place the drawer
rail on the guides.
D14 Push the drawer
in until it stops.
Stop
D15
Lift the front of the drawer and push in
until the stops clear the guides.
D16
Lower the front of the drawer and
push in until it closes.
SPECIAL INSTRUCTIONS IF YOU HAVE
PROBLEMS WHILE REPLACING THE
STORAGE DRAWER
IF DRAWER WON'T CLOSE
Drawer Does
Not Close
Completely
Drawer Front Panel
Tipped Away From
Body Side
Power Cord May Be
Obstructing Drawer
In This Area
Rear Drawer Support
Is Resting On Top of
Guide Rail
Remove and replace, making sure the power
cord is not obstructing the drawer and/or the
rail is in the guide.
IF DRAWER IS CROOKED
Rear Drawer Support is
On Top of Guide Rail
On the High Side
Drawer Front Panel
Tipped to One Side
Remove and replace making sure the rail is in
the guide.
10
Installation Instructions
E
Final Check List
Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced.
Be sure power is in service to the building.
Check to be sure that all packing materials and tape on metal panel (if applicable) under
control knobs have been removed.
F
Operation Check List
Check to make sure the Clock display is energized. If a series of horizontal red lines appear
in the display, disconnect power immediately. Recheck the range wiring connections. If
change is made to connections, retest again. If no change is required, have building wiring
checked for proper connections and voltage. It is recommended that the clock be changed if
the red lines appear.
Push in and turn any one of the four surface knobs to “MED” setting to observe that the
element glows within 60 seconds. Turn the knob off when glow is detected. If the glow is not
detected within the time limit, recheck the range wiring connections. If change is required,
retest again. If no change is required, have building wiring checked for proper connections
and voltage.
11
NOTES
12
Pub. No. 31-10513
229C4053P493