Download Honeywell HRDP DVR DVR User Manual

MazdaGuide550_0351A.hls
8/10/05
3:23 PM
Page 1
9. Return to the vehicle and firmly press,
hold for 2 seconds and release the
®
programmed HomeLink button. Fig. 5
Hold for 2 seconds and
release
Auto-Dimming Mirror User Guide
10. Repeat Step 9 a second time and
possibly a third time (depending on
brand of device).
®
HomeLink should now activate your
rolling code equipped device.
Congratulations! Your new Mazda is equipped with an Automatic-Dimming Mirror,
manufactured by Gentex Corporation. During nighttime driving, this safety feature will
automatically detect and eliminate dangerous rearview mirror glare.
Fig. 5
Gate Operator / Canadian Programming:
Your new mirror may or may not have all of the features shown in this User Guide.
Please refer only to the sections that pertain to the model mirror you have in your new
vehicle.
Canadian radio-frequency laws require transmitter signals to “time-out” or quit after
®
several seconds of transmission – which may not be long enough for HomeLink to pick
up the signal during programming. Similar to this Canadian law, some U.S. gate
operators are designed to “time-out” in the same manner.
Auto-Dimming Mirror with Compass
If you live in Canada or you are having difficulties programming a gate operator by using
the “Programming” procedures (regardless of where you live), replace “Programming
®
HomeLink step 4 with the following:
ON/OFF
ON/OFF
BUTTON
BUTTON
NOTE: If programming a garage door opener or gate operator, it is advised to unplug
the device during the “cycling” process to prevent possible overheating.
DISPLAY
DISPLAY
WINDOW
WINDOW
LED
LED
SENSOR
SENSOR
To Operate the Auto-Dimming Feature:
Feature:
®
4. Continue to press and hold the HomeLink button while you press and release
- every 2 seconds (“cycle”) your hand-held transmitter until the frequency signal
®
has successfully been accepted by HomeLink . (The indicator light will flash
slowly and then rapidly.)
Proceed with “Programming” step 5 to complete.
®
NOTE: Programmed HomeLink codes can be intentionally erased (when selling
vehicle etc.) by holding the 2 outer buttons (as shown in Fig. 1) for 20 seconds until LED
indicator begins to flash. Do not hold buttons for more than 30 seconds.
If you have any questions or are having difficulty programming your
®
HomeLink buttons, please refer to www.homelink.com or call
1-800-355-3515.
Push the “ ” switch to turn the mirror
mirror on/off.
on/off. The
The auto-dimming
auto-dimming feature
featureisis
enabled when the green LED indicator
indicator is
is on.
on.
To Operate the Compass Feature:
Feature:
1.
2.
2.
3.
3.
Push the display “ ” switch. The
The vehicle’s
vehicle’s directional
directional heading
heading will
will be
bedisplayed.
displayed.
Pushing the
the ““ ”” switch
switch aa second
second time
time will
will turn
turn off
off the
the visual
visual display.
display.
Pushing
If
the
display
reads
“C”,
calibrate
the
compass
by
driving
the
vehicle
in
If the display reads “C”, calibrate the compass by driving the vehicle inup
upto
to33
complete circles
complete
circles at
at less
less than
than 55 MPH.
MPH.
CALIBRATION
CALIBRATION PROCEDURE
PROCEDURE
Cleaning the mirror:
When cleaning the mirror, use a paper towel or similar material dampened with
glass cleaner. Do not spray glass cleaner directly onto the mirror as damage to
internal circuitry may result.
Troubleshooting Guidelines:
1. “C” or “CAL” is displayed in the display window
a. Perform calibration procedure.
2. Inaccurate compass direction
a. Perform compass zone setting procedure and then calibration procedure
b. Vehicle magnetics may have changed.
- Press and hold the “ ” button or the “ ” button (if mirror has) for 9
seconds until a “C” or “CAL” appears in the display window.
- Perform calibration procedure.
4. To adjust for compass variance:
a. Press the “ ” button for more than 9 seconds, or until the current zone
number appears in the display.
b. Find your current location and variance zone number on the zone map below.
c. Press the “ ” button until the new zone number appears in the display.
After you stop pressing the button, the display will show a compass heading
within a few seconds.
NOTE: Installing items such as a ski rack, antenna, luggage rack or recent body
repair can cause changes to the vehicle’s magnetic field. This may require
that the compass be recalibrated by performing the recalibration procedure.
3. The temperature display is reading significantly low
a. The temperature display may have been changed to degrees Celsius. Refer
to the section of this User Guide pertaining to the temperature feature to
correct.
4. The display window shows “SC” or “OC” instead of temperature
a. These problems must be corrected at your authorized Dealer Service Center.
FCC: NZLCTHL3. IC: 4112A-NZLCTHL3
550-0351 B
MazdaGuide550_0351A.hls
8/10/05
3:23 PM
Page 3
Auto-Dimming Mirror with Compass and HomeLink®
and
Auto-Dimming Mirror with Compass, HomeLink®
and Temperature
To Operate the HomeLink® Feature:
Please refer to the programming instructions outlined in this User Guide or:
®
a. visit the HomeLink website at www.homelink.com
®
b. call the HomeLink customer support line at 1-800-355-3515
HomeLink® Programming Instructions:
DISPLAY WINDOW
WINDOW
DISPLAY
(Larger window
window for
for
(Larger
Temp. model)
model)
Temp.
HOMELINK
HOMELINK
BUTTONS
BUTTONS
LED
LED
AUTO-DIMMING
AUTO-DIMMING
ON/OFF BUTTON
BUTTON
ON/OFF
SENSOR
SENSOR
DISPLAY
DISPLAY
BUTTON
BUTTON
To Operate the Auto-Dimming Feature:
Push the
th e ““ ” switch to turn the mirror on/off. The auto-dimming feature is enabled
Push
when the
the green
green LED
LED indicator
indicator is
is on.
on.
when
WARNING! Before programming HomeLink to a garage door opener or gate
operator, make sure that people and objects are out of the way of the device to prevent
potential harm or damage. When programming a garage door opener, it is advised to
®
park outside of the garage. Do not use HomeLink with any garage door opener that
lacks safety stop and reverse features as required by U.S. federal safety standards (this
includes any garage door opener model manufactured before April 1, 1982). A garage
door that cannot detect an object – signaling the door to stop and reverse – does not
®
meet current U.S. federal safety standards. For more information, contact HomeLink at
www.homelink.com or by calling 1-800-355-3515.
®
1. To begin, press and hold the 2 outer
®
HomeLink buttons (to clear memory) until
the indicator light (LED) blinks slowly
(approximately 20 seconds). Fig. 1
To Operate the Compass Feature:
1. Push
Push the
the display
display ““ ”” switch.
switch. The
The vehicle’s
vehicle’s directional
directional heading
heading will
will be
be displayed.
displayed.
1.
2. Pushing
Pushing the
the ““ ”” switch
switch aa second
second time
time will
will turn
turn off
off the
the visual
visual display.
display.
2.
3. If the display
display reads
reads “C”
“C” or
or “CAL”,
“CAL”, calibrate
calibrate the
the compass
compass by
by driving
driving the
the vehicle
vehicle in
in
3.
up to
to 33 complete
complete circles
circles at
at less
less than
than 55 MPH.
MPH.
up
2. Release both buttons.
CALIBRATION PROCEDURE
PROCEDURE
CALIBRATION
Fig. 1
Press and Hold for 20 seconds…
LED blinks slowly…
Release buttons
Press and hold both…
LED blinks fast…
Release both buttons
4. To adjust for compass variance:
a. Press the “ ” button for more than 9 seconds, or until the current zone
number appears in the display.
b. Find your current location and variance zone number on the zone map below.
c. Press the “ ” button until the new zone number appears in the display. After
you stop pressing the button, the display will show a compass heading within
a few seconds.
NOTE: Do not hold the buttons for longer than
30 seconds. Do not repeat this step when
programming additional devices to remaining
buttons.
3. Position the end of the hand-held transmitter
®
1-3 inches away from the HomeLink button
you wish to program while keeping the
the indicator light in view.
4. Simultaneously press and hold both the
®
chosen HomeLink and hand-held transmitter
buttons. Fig. 2
Do not release the buttons until step 5 has
been completed.
NOTE: Some gate operator and garage door
openers may require you to replace this
Programming step 4 with procedures noted in the
“Gate Operator / Canadian Programming” section.
Fig. 2
®
5. After the HomeLink indicator light changes
from a slow to a rapidly blinking light, release
®
both the HomeLink and hand-held transmitter
buttons.
Fig. 3
Press button…
Fast blink for 2
seconds then constant
= rolling code…
Continue programming
instructions
®
®
HomeLink and the HomeLink house are registered trademarks of Johnson Controls, Inc.
®
If the indicator light blinks rapidly for 2 seconds
and then turns to a constant light, the device being
programmed utilizes rolling code and
programming is not complete until the following
steps are completed. Fig. 3
7. On the garage door opener receiver
(motor-head unit) locate the “learn” or “smart”
button. This can usually be found where the
hanging antenna wire is attached to the
motor-head unit.
To Operate the Temperature Feature:
1. Push the “ ” switch. The vehicle’s directional heading and outside temperature will
be displayed.
2. Pushing the “ ” switch a second time will turn off the visual display.
3. The temperature display can be changed to Celsius by depressing the “ ” switch for
3 seconds, until a “°C” appears by itself in the display window. Pushing the “ ” switch
again will toggle the display between Celsius and Fahrenheit. Five seconds of no
switch activity returns the display to its normal directional and temperature reading.
6. Press and hold the just-trained HomeLink
button and observe the indicator light.
8. Firmly press and release the “learn” or
“smart” button. Fig. 4
Fig. 4
Press “Learn” button…
30 SECONDS TO GET TO VEHICLE
NOTE: You have 30 seconds to initiate step 9.