Download Macrom M-HPB30.B User manual
Transcript
USER MANUAL M-HPB30.B M-HPB30.W Table of contents EN Warranty Safety information Specifications Product overview Charge the battery Switch On/Off Pairing and connecting with a Bluetooth device Re-connecting with a Bluetooth device Adjust the Volume Manage phone calls Listen to music Auxiliary input Micro USB input Product care -2- 3 3 3 4 5 5 6 6 6 7 7 8 8 8 EN Warranty Thank you for purchasing this Macrom product. Should your product need warranty service, please return it to the shop where you buy it or to the Macrom distributor in your country . The warranty does not cover damage due to improper use and or installation, incorrect connections to power supply and audio video sources, exposure to excessive humidity, unauthorized repair attempts or modifications. Safety information To prevent hearing damage when listening the headphones gradually turn up the volume until you reach a pleasant and safe listening level. Pay attention to do not use the headphones when your full attention to your surroundings is required. For example is not safe (or even illegal in some countries) to use headphones while driving a vehicle or crossing a street. Specifications M-HPB30 can make and receive calls hands-free with compatible mobile phones and listen to music from a compatible music players. The operating range is within 10 meters. M-HPB30 is compliant with the following Bluetooth® specifications: Bluetooth V4.0 and supports HSP, HFP, A2DP and AVRCP profiles. Power supply input 5V DC - 0.5 A. -3- EN Product overview Size adjustment. Track forward Pause/Play MFB (Multi function button) Track back Volume up Volume down USB micro connector Status indicator LED Auxiliary input -4- EN Charge the battery Use the Micro USB cable provided with the product to charge the battery. Plug it in the connector located under the rigth ear cup of the headphone, then plug the other end into a compatible USB charger or a USB port of a computer. The status indicator LED is steady red while charging or steady blue if the battery is fully charged. For a faster charge please remember to power off the headphone before charging the battery. The fully charged battery allows up to 16 hours of continuous music playback or phone calls. The maximum standby time is approximately 100 hours. Is possible to listen to music and/or make phone calls while charging the battery. If the battery needs to be charged the headphone will prompt a three tones every 30 seconds and the status indicator LED flashes red. Switch On/Off To switch ON, press and hold the MFB key about 3 seconds until the headphone prompts 4 ascending tones and the status indicator LED blinks blue. To switch OFF, press and hold the MFB key about 3 seconds until the headphone prompts 4 descending tones and the status indicator LED switch off. -5- EN Pairing and connecting with a Bluetooth device To enter pairing mode, make sure the headphone is powered off then press and hold the MFB key about 6 seconds until the headphone prompts 4 ascending tones and after a while 2 more tones and the status indicator LED blinks red and blue alternately. From the Bluetooth function of the device to be paired search for new device named “M-HPB30”. Select it and if requested enter “0000” passcode. When pairing is completed successfully the indicator LED blinks blue and the headphone prompts two tones. If the pairing procedure is not successful, please switch off the headphone and repeat the above steps. The specific pairing procedure may vary, so please refer to your device user manual for further information. When in pairing mode, if no device is paired within 2 minutes, the headphone will return to standby mode automatically. Re-connecting with a Bluetooth device Every time the headphone is switched on, it will connect to the last connected device automatically. When the headphone is in standby mode and doesn’t connect to any HFP devices, short press MFB button once, it will connect to last connected source device automatically. Adjust the Volume To adjust the headphone volume during a call or while listening to music press the volume up or down keys. When the volume is turned to maximum or minimal levels, one tone is prompted. Please remember that excessive sound pressure from headphones can damage your hearing. -6- To receive a phone call from the mobile phone use it as usual. To manage the phone from the headphone refer to the commands below: Pick up a call: Short press MFB key when the phone rings. Reject a call: Press and hold MFB key for 2 seconds. Hung up a call: Short press MFB key once. Swap call audio: Press and hold MFB key for 2 seconds. Microphone mute/un-mute: Short press MFB key twice. Redial the last number: Short press MFB key twice. Take an incoming call dropping the first one: Short press key once. key twice. Reject an incoming call keeping the first one: Short press Switch calls: Press and hold key for 2 seconds. Hung up current mutiple calls: Short press key once or twice to keep second call active. With some mobile phones, if an incoming call is accepted using the phone commands the conversation will be automatically transferred to the phone. To transfer it back to the headphone use the audio source switch of the phone. Refer to the phone user manual for further information. Listen to music Connect the headphone to a compatible music player that supports A2DP profile. Please note that the music functions available depends on your music player. If a call is received or originated while listening to music, the music will be paused until the call ends. To manage music from the headphone refer to the commands below: Pause/Play: Short press key. Track back: Short press ◄ key. Track forward: Short press ► key. Fast back: Press and hold ► key. Fast forward: Press and hold ◄ key. -7- EN Manage phone calls EN Auxiliary input To connect a device to the auxiliary input use the cable provided with the unit. If a connector is plugged in the auxiliary input the Bluetooth function is automatically disabled. Bluetooth functions is automatically resumed when the connector is removed from the auxiliary input. Micro USB input To listen music from a computer, use the micro USB cable provided with the headphone. Plug it in the micro USB connector located under the rigth ear cup of the headphone, then plug the other end into an USB port of a computer. When the headphone is plugged to computer the Bluetooth function is automatically disabled. Bluetooth functions is automatically resumed when the micro USB cable is removed from the micro USB connector. If the automatically reconnection does not work, please switch off the headphone and repeat the pairing procedure. Product care Please remember that your Macrom product is an electronic device, and so needs to be treated with care: Do not subject it to mechanical shock or vibrations. Do not subject it to eccessive heat. Keep it away from water and excessively humid areas. Keep it away from high electromagnetic fields. There are no user-serviceable parts inside. Opening the product or try to repair it will terminate the warranty. -8- The BLUETOOTH ® worldmark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by ALDINET S.p.A. is under license. The MACROM brand is a registered trademark of ALDINET S.p.A. Declaration of Conformity ALDINET S.p.A Viale C. Colombo, 8 - 20090 Trezzano s/N (MI) - Itlaly Tel. +39 02 484781 w w w . m a c r o m . i t