Download Clarion DPH910 Specifications
Transcript
Power Guard Circuit This by far is the most important feature the APA4300HX offers, as the amplifier’s input stage prevents the generation of clipping distortion by holding down the gain when overdrive distortion is detected at the output stage. By removing only distortion elements, the amplifier protects speakers from potential damage while also maintaining the amplifiers superior sound qualities. Power Guard Clarion Amp Conventional Amp multiple satellite speakers in stereo, as well as a subwoofer in a bridge mono configuration. This eliminates the need for active crossovers while allowing for a multi-speaker system. 2-Ohm Stability Clarion APA4320 and APA2160 amplifiers are designed to driver lower impedance loads for increased power output and can be bridged for mono operation across a 2-ohm load. This allows the amplifiers to run multiple speakers in more complex systems. The result is an amplifier that can provide 150% more power in 2-ohm stereo, or more than 300% in 2-ohm bridged mono. Multi-Channel Amplifiers 4-Part Digital Meter The APA4300HX offers this unique feature so users will always be in tune with its performance. This four-part digital meter allows the user to monitor the amplifier’s real-time power output level and consumption, voltage level and internal temperature. Low-Loss High-Output Power Supply Clarion equips the APA4300HX’s power supply with a high-performance, low-loss, MOS-FET-based PWM-type DC/DC converter. The amplifier’s circuit structure boasts large-capacity, low-impedance capacitors, and a large toroidal choke coil, a super thin circuit board and a copper bus bar. The result is a power supply that maintains stability, even during sudden signal changes. Toroidal Choke Coils Used in the power supply circuitry, these type of coils are resistant to magnetic noise and have a low DC resistance. This contributes to the amplifier’s high efficiency, lownoise power supply. Amplifier Technologies Clarion’s amplifier power supply technologies include an input voltage compensation circuit, an active regulator feedback circuit, and voltage-input protection. The incorporated double-sided circuit boards use heavy-duty copper/tin-plated bus bars and direct-mount connectors. Built-in crossovers are standard on all amplifier models. Other features include a discrete driver and highcurrent output transistor pairs, along with a solid-state muting circuit. These features provide Clarion’s amplifier line with stable and well-protected power supplies, quieter operation, better signal-to-noise ratios and transient response, as well as the ability to handle lower impedance loads. This translates into amplifiers with great reliability and flexibility. Mixed Mode Operation Clarion’s multi-channel amplifiers provide four channels of amplification on one circuit board, all enclosed in a single chassis. Moreover, all models are equipped with on-board high-pass/low-pass electronic crossovers. This configuration provides maximum system flexibility using a single amplifier. For example, the front channels can drive full-range speakers with front crossovers “off,” while rear channels are set to low-pass and bridged to drive a single subwoofer. Or, the front channels can be set to high-pass to drive a pair of satellite speakers, and rear channels set to low-pass to drive a pair of woofers. Pulse-Width-Regulated MOS-FET Power Supply This type of power supply converts the battery voltage to a higher voltage (i.e., +30 volts or greater) than the amplifier requires for maximum power output. Unless the power supply increases 12-volt battery power, the amplifier cannot produce more than about 25 watts (rms). The power supply delivers the proper amounts of current and voltage to the amplifier’s output stages over a wide range of loads, and varies the pulse width to accommodate different load conditions. Pulse-width regulation adjusts the width of the power supply’s switching pulses to serve constantly-changing audio power needs. When music dynamics increase, or the volume is raised, the pulses stay on longer to charge the power supply capacitors across the DC rail in the power supply. By using this type of power supply, Clarion can build a smaller amplifier that generates less heat and is more efficient. Another advantage to this type of supply is that it can deliver its rated power over a wide range of input voltages. This means the amplifiers will deliver their rated power over a voltage swing of 11.6 to 14.7 volts. The result is an amplifier that can produce maximum power into a 2-ohm load without losing output power under lower voltage conditions. Pulse Width Increases Pulse Width Decreases Amplifier Circuit Information The input and output of Clarion’s amplifiers incorporate complex circuitry for both the input and output sections. This offers better noise suppression, fast transient response and minimum distortion. This includes highimpedance differential input stages, global feedback, and premium devices with very high slew rates. High-impedance differential input stages separate the input signal ground from the common chassis ground. This creates a very effective ground-loop isolation circuit that reduces the possibility of charging system noise from entering the signal path. Feedback is a method of controlling the distortion in an amplifier’s output by feeding a portion of the output signal to the input of the amplifier. At Clarion, we use global feedback circuits instead of the more commonly-used local feedback type (i.e., the ability of a device to quickly respond to an input signal). This reduces distortion, boosts the signal-to-noise ratio, and increases the amplifier’s overall transient response. These advanced circuit topologies ensure that Clarion’s amplifiers will accurately reproduce all the dynamics and subtleties found in today’s digital recordings. At the same time, noise suppression circuits work to effectively eliminate induced electrical system noise, which contributes to the dynamic range of the amplifiers. APA4300HX4/3/2-Channel Amplifier • 600 Watts Maximum Power Output • Bridgeable 3/2-Channel Mode Operation • Power Guard Circuit • Low-Loss Power Supply • Stable Down to 1-Ohm Load in Stereo • Variable 4-Channel Low- and High-Pass Filter (50 to 200Hz) • Bass Extender (40Hz to 120Hz, 0 to +12dB) • Four-Part Digital Display • Aluminum Housing Built-In Cooling Fan • Speaker Level Input Terminal • 100kHz Frequency Reproduction • Gold-Plated Connectors Cosmetic Design: The APA4320 and APA2160 The versatility these two amplifiers offer is directly related to the compact design both offer. This is made possible by an exclusive heat sink design and aluminum die-cast body, which offers efficient heat dissipation during operation. This eliminates the need for an internal fan, resulting in an amplifier with a smaller footprint. Clarion further enhances the look of the amplifier with a stylish ovalshaped emblem, which incorporates three blue LEDs. Gold-Plated RCA Connectors and Terminals Superior conductivity is achieved by using gold-plated RCA and power supply terminals to minimize contact resistance and noise. Moreover, because gold is unaffected by external magnetic fields, magnetic distortion is reduced. Gapped E-Core Choke Coils APA4320 4/3/2-Channel Amplifier • 640 Watts Maximum Power Output • Bass Extender Control (0 to 15dB @ 45Hz) • Adjustable High- and Low-Pass Crossover (55Hz to 550Hz, 12dB/Oct.) • Mixed Mode Operation • 3/2-Channel Operation • MOS-FET Output Design • Double-Sided FR4 PC Board • Gold-Plated RCA Connectors Utilized in the power supply, the Gapped E-Core choke coils offer low impedance and resistance to harmful magnetic impedance. This results in a more efficient amplifier and a low-noise power supply. Variable High-/Low-Pass Crossover Amplifiers armed with these two features allows users to make frequency adjustments over all channels so that a multi-amplifier and subwoofer system can be configured with ease. APA2160 2/1-Channel Amplifier More Current Supplied • 320 Watts Maximum Power Output • Bass Extender Control (0dB to 15dB @ 45Hz) • Adjustable High- and Low-Pass Crossovers (55Hz to 550Hz, 12dB/Oct.) • Mixed Mode Operation • 2/1-Channel Operation • MOS-FET Output Design • Speaker Level Input Terminals • Double-Sided FR4 PC Board • Gold-Plated RCA Connectors Less Current Supplied Higher Audio Signal Lower Audio Signal This feature is the key behind the versatility of the APA4320 and APA2160 amplifiers. By utilizing an inverting circuit, a single 2-channel amplifier can drive 28 Amplifier Breakdown 2005 Product Application Guide 2005 Product Application Guide 29