Download Sears 113.243311 Operating instructions

FULL ONE YEAR WARRANTY
If within
one year from the date of purchase,
or workmanship.
Sears
will repair
it, free
WARRANTYSERVICE
IS AVAILABLE
CENTER/DEPARTMENTTHROUGHOUT
THiS
WARRANTY
This warranty
to state.
APPLIES
gives
SEARS.
general
ONLY
ON CRAFTSMAN
this Craftsman
Band Saw fails due to a defect
THiS
PRODUCT
THE
IS IN
legal rights, and you may also have other
ROEBUCK
AND
safety
in materia!
698/731A,
instructions
Sears Tower,
for
NEARESTSEARS
USE
you specific
CO..
SAW
of charge.
BY SIMPLY
CONTACTING
THE UNITED
STATES
WHILE
SAND
iN THE
UNITED
rights which
Chicago,
SERVICE
STATES
vary from
state
IL 60684
power
tools
1. KNOW YOUR POWER TOOL
mask if cutting
(plugs or muffs)
Read and understand
the owner's manua
and labels
affixed to the tool. Learn its a pplication
ana limitations
as well as the specific potential
hazards peculiar to this
13. SECURE WORK
toot.
2. GROUND
This
toot
Use clamps or a v=se to hold work when practical.
It's
safer than using your hand, frees both hands to operate
tool.
ALL TOOLS
is equipped
with
an
approved
3-conductor
cord and a 3-prong grounding
type plug to fit the proper
grounding
type receptacle.
The green conductor
in the
cord is the grounding
wire. Never connect
the green w_re
to a live terminal.
3. KEEP GUARDS
- in working
ment.
14. DON'T OVERREACH
Keeo orooer
and in proper
adjustment
Keep
once.
and align-
KEYS AND WRENCHES
17. AVOID
Cluttered
areas and benches
mvite
accidents.
must not be slippery due to wax or sawdust.
DANGEROUS
Floor
Make
7. KEEP CHILDREN
should
ENVIRONMENT
MAKE
WORKSHOP
C MILD-PROOF
-- with
padlocks,
switches
master
Consult
Follow
switch
starter
Do
9. DON'T FORCE TOOL
rate for which
or attachment
to do
a job
it was not
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
(rings,
wristwatches)
To get caught iF moving
parts.
NONSLIP
footwear
is recommended.
Wear protective
hair covering
to contain
long hair. Roll long sleeves
above the elbow.
GOGGLES
before
p[uggmg
accessories.
accessories.
may cause hazards,
not
store
materials
above
is t_pped
or near me tool
to stand on the tool
or if the
such that
to reach them.
PARTS
Before further use of the tool, a guaro or other part that
=s damaged should be carefully
checked to ensure that _t
will operate properly
and perform
its mtended
function.
Check for alignment
of moving parts, binding
of moving
parts, breakage
of parts, mountmg,
and any other conditions
that may affect
its operation
A guard or other
cart that
s damaged
should
be properly
reoaired
or
replaced.
TOOL
Don't
force tool
designed for,
13osltion
ACCESSORIES
accessories
20. CHECK DAMAGED
and safer at the
as
STARTING
is an "OFF"
Serious injury could occur if the tool
cutting tool is accidentally
contacted.
or by removing
sucn
19. NEVER STAND ON TOOL
work area_
it _snecessary
It will do the job better
it was designed.
accessories
the owner's manual for recommended
the instructions
that accompany
the
The use of improper
keys,
12. USE SAFETY
ACCIDENTAL
sure
18. USE RECOMMENDED
AWAY
be kept a safe distance from
changing
In.
Don't
use power tools in damp or wet locations
or expose mere to rain. Keep work area well lighted, Provide
adequate surrounding work space,
10. USE RIGHT
oerformchangmg
TOOLS
before
servicing;
when
blades, bits, cutters, etc.
5. KEEP WORK AREA CLEAN
8,
at all times.
tools sharp and clean for best and safest
Follow
mstructions
for luOncatlng
and
16. DISCONNECT
Form habit of checking
to see that keys and adjusting
wrenches are removed from toot before turning
it on
All visitors
and balance
TOOLS WiTH CARE
accessories.
4. REMOVE ADJUSTING
0. AVOID
footing
15. MAINTAIN
IN PLACE
oraer,
operation
is dusty,
and ear protectors
during extended
periods of operation.
21. DIRECTION
OF FEED
Feed work into a blade or cutter against the direction
rotation
of the blade or cutter only.
22. NEVER LEAVETOOL
UNATTENDED
(Head Protection)
Wear safety goggles (must comply with ANSI Z87.1) at all
times. "Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses." Also. use face or dust
Turn
power off.
complete stop.
2
Don't
o!
RUNNING
leave tool
until
it comes to a