Download RADWAG PS1000.R2 User manual

User manual no.:
LMI-38-06/04/13/ENG
Precision balances
PS/X
series
BALANCES AND SCALES
RADWAG 26 – 600 Radom, Bracka 28, POLAND
Phone: +48 (0-48) 38 48 800, fax. +48 (0-48) 385 00 10
[email protected]
www.radwag.com
APRILE 2013
-2-
Table of Contents
1. TECHNICAL DATA ........................................................................................................5
Balances PS/X series with weighing pan 128 x 128 mm: ........................................5
Balances PS/X series with weighing pan 195 x 195 mm: ........................................6
2. BASIC INFORMATION ..................................................................................................7
2.1. Intended use ......................................................................................................7
2.2. Inappropriate use ..............................................................................................7
2.3. Warranty .............................................................................................................7
2.4. Monitoring metrological parameters of the balance ......................................7
2.5. Data included in this user manual ...................................................................8
2.6. Staff training ......................................................................................................8
3. TRANSPORT AND STORAGE ......................................................................................8
3.1. Delivery check ...................................................................................................8
3.2. Packaging...........................................................................................................8
4. UNPACKING, ASSEMBLING AND STARTUP ..............................................................9
4.1. Assembling and place of use ...........................................................................9
4.2. Unpacking ........................................................................................................10
4.3. Leveling ............................................................................................................11
4.4. Standard equipment ........................................................................................11
4.5. Cleaning ...........................................................................................................11
4.6. Plugging to mains ...........................................................................................11
4.7. Connecting peripheral devices ......................................................................11
5. BASIC FUNCTIONS .....................................................................................................12
6. DESCRIPTION .............................................................................................................13
6.1. Graphic display................................................................................................13
6.2. Keyboard ..........................................................................................................14
6.3. Sockets and interfaces ...................................................................................15
7. USER MENU ................................................................................................................15
7.1. Moving through the menu...............................................................................19
7.2. User menu - content ........................................................................................21
8. WEIGHING ...................................................................................................................23
8.1. User log in function .........................................................................................25
9. BALANCE ADJUSTMENT ...........................................................................................28
9.1. Automatic balance adjustment.......................................................................28
9.2. Adjustment test ...............................................................................................31
9.3. Manual adjustment ..........................................................................................31
9.4. Adjustment report printout .............................................................................33
10. DETERMINING CONTENT OF A PRINTOUT FOR GLP PROCEDURES...................35
11. DATE AND TIME SETTINGS .......................................................................................35
12. SETTING BALANCE OPERATING PARAMETERS....................................................38
12.1. lter settings ......................................................................................................38
12.2. Value release....................................................................................................38
12.3. Time interval of display refreshment .............................................................38
12.4. Autozero function ............................................................................................39
-3-
12.5. Last digit...........................................................................................................39
12.6. Negative ...........................................................................................................39
12.7. Operating conditions ......................................................................................39
13. RS 232 FUNCTIONS ....................................................................................................40
14. PRINTOUTS .................................................................................................................41
15. SETTING ACCESSIBILITY OF MEASURING UNITS..................................................41
16. SETTING ACCESSIBILITY OF WORKING MODES ...................................................42
17. OTHER PARAMETERS ...............................................................................................43
18. WORKING MODES ......................................................................................................45
18.1. Parts counting of the same mass ..................................................................45
18.2. Checkweighing ................................................................................................48
18.3. Filling ................................................................................................................52
18.4. Percent setup ...................................................................................................53
18.5. Animal weighing ..............................................................................................57
18.6. Density determination of solids and liquids .................................................58
18.7. Formulation ......................................................................................................60
18.8. Statistics...........................................................................................................64
19. PRINTOUTS .................................................................................................................67
19.1. Standard printout ............................................................................................67
19.2. Non-standard printouts ...................................................................................68
20. COOPERATION WITH A PRINTER OR A COMPUTER .............................................74
20.1. Cross-section through connecting cables ....................................................74
21. COOPERATION WITH A CITIZEN LABEL PRINTER .................................................75
22. COOPERATION WITH EPSON RECEIPT PRINTER ..................................................80
23. UNDER HOOK WEIGHING ..........................................................................................81
24. CONNECTING EXTERNAL BUTTONS .......................................................................81
25. LIST OF COMMANDS COMPUTER - BALANCE .......................................................81
26. ERROR MESSAGES....................................................................................................84
-4-
1.
TECHNICAL DATA
Balances PS/X series with weighing pan 128 x 128 mm:
PS 200 /
2000/X
PS 250/X
PS 450/X
PS 750/X
PS 1000/X
Max.
capacity
200 / 2000g
250g
450g
750g
1000g
Tare range
-2000g
-250g
-450g
-750g
-1000g
Min. load
0,02 g
0,02 g
Readability
0,001/0,01 g
0,001 g
Repeatability
0,001/0,01 g
0,001 g
0,0015 g
Linearity
± 0,002 / 0,01g
± 0,002 g
± 0,003 g
Working
temperature
Power
supply
Sensitivity
drift
Pan size
+10 °C ÷ +40 °C
13,5-16 V DC / 2.1 A
2 ppm/°C in temperature +15°C - +35°C
128 x 128mm
Dimensions:
-5-
Balances PS/X series with weighing pan 195 x 195 mm:
PS 1500/X
PS 2500/X
PS 4500/X
PS 6000/X
PS 8000/X
Max. capacity
1500g
2500 g
4500 g
6000g
8000g
Tare range
-1500g
-2500 g
-4500 g
-6000g
-8000g
Min. load
0,5 g
Readability
0,01 g
Repeatability
0,01 g
0,015g
0,015g
Linearity
± 0,02 g
± 0,03 g
± 0,03 g
Working
temperature
+10 °C ÷ +40 °C
Power supply
13,5-16 V DC / 2.1 A
Sensitivity drift
2 ppm/°C in temperature +15°C - +35°C
Pan size
195 x 195mm
Dimensions:
-6-
2.
BASIC INFORMATION
2.1. Intended use
Precision balance PS/X series is designed to determining the weighing value of loads
in laboratory environment. It is intended for application as a non-automatic weighing
instrument only, i.e. the material to be weighed should be manually and carefully
placed in the center of the weighing pan. Weighing result should be read only after
stable reading has been obtained – stability pictogram is visible on balance’s display.
2.2. Inappropriate use
Do not use the balance as a dynamic weighing instrument. Even if small quantities of
weighed material are added or removed from the weighing pan of the instrument, the
reading should be taken only after stabilization of the measurement result. Do not
place any magnetic materials on the weighing pan, as this can cause damage of the
measuring system of the instrument. Be sure to avoid impact shock and overloading
the balance in excess of the prescribed maximum measuring range (max capacity),
minus any possible tare weight that has been applied. Never use the balance in an
environment endangered by an explosion. This balance has not been adjusted for
operation in explosive areas. There must not be any modification made to the balance.
2.3. Warranty
Warranty is not valid at the following:
•
•
•
•
•
•
Non-observation of the guidelines of this user manual,
Use of balance other than specified in this manual,
Alternation to or opening of the device (damaged of the protective stickers),
Mechanical damage and damage caused by media, natural water, and tear,
Inappropriate assembling or defects of electric installation,
Overloading of the measuring instrument.
2.4. Monitoring metrological parameters of the balance
Metrological characteristics of the balance requires periodical inspection carried out by
its operator. Inspection frequency is conditioned by ambient conditions in which the
balance is used, types of performed processes and accepted quality management
system in an organization.
-7-
2.5. Data included in this user manual
Please read the user manual carefully before assembling and startup, even if the user
is experienced with this type of weighing instruments.
2.6. Staff training
This balance should only be operated and maintained by personnel who is trained and
experienced in using this type of balances.
3.
TRANSPORT AND STORAGE
3.1. Delivery check
Please check the packaging immediately upon delivery and the device during
unpacking for any visible signs of external damage.
3.2. Packaging
Please retain all parts of the original packaging should the balance be transported in
the future. Only the original packaging should be used for dispatching the balance.
Before packing, disconnect all attached cables and remove any loose/movable parts
(weighing pan, anti-draft shields, etc.). Please place balance and its components in
their original packaging, and protect them against damage during transport.
-8-
4.
UNPACKING, ASSEMBLING AND STARTUP
4.1. Assembling and place of use
•
Balance should be stored and used in locations free of vibrations and shakes, free
of air movement and dust,
•
Ambient air temperature should not exceed the range of: +10 C ÷ +40 C
•
During balance operation, ambient temperature in the weighing room should not
change more than 3°C within one hour,
•
The balance should be located on a stable wall console desk or a stable working
table which is not affected by vibrations and distant from heat sources,
•
Take special safety measures when weighing magnetic objects, as part of the
balance is a strong magnet. Should such loads be weighed, use under hook
weighing option, which removes the weighed load from area influenced by the
balance’s magnet. For assembling the hook for under hook weighing option see the
bottom section of balance’s housing,
•
In order to avoid influence of static electricity on the measurement process, ground
the balance’s housing. The grounding bolt is located at the back of balance’s
housing.
o
-9-
o
4.2. Unpacking
Carefully remove the balance from its packaging, remove the plastic, foil and
cardboard transport protective elements and gently place the balance in its intended
place of use. Assemble the weighing pan, and other elements according to below
scheme:
Assembling components of a balance with measuring accuracy 10 mg:
Remove the protective tape securing
the mass spring on one of the rubber
mandrels (2),
Assembly the weighing pan (1) onto
the rubber mandrels (3),
On assembling check whether the
weighing pan is placed firmly on the
rubber mandrels.
Assembling components of a balance with measuring accuracy 1mg:
Remove the protective tape securing the
mass spring on one of the rubber
mandrels (3),
Assembly the weighing pan (2) onto the
rubber mandrels (4),
Assembly the anti-draft shield (1) onto
the top housing of the balance,
On assembling check whether the
weighing pan is placed firmly on the
rubber mandrels.
Fig. 1. Assembling components of a balance PS/X series
- 10 -
4.3. Leveling
Before plugging to mains, level the device using two adjusting feet
located at the back of balance’s housing. Turn the adjusting feet in a
way that the air bubble of the level is placed centrally. The level is
located at the back wall of balance’s housing.
4.4. Standard equipment
•
•
•
•
Balance.
Weighing pan and protecting (anti-draft) components.
Power adapter.
User manual on a CD.
4.5. Cleaning
Balance should be cleaned with damp cloth by gentle wiping the smudges of dirt. In
order to clean the weighing pan of the balance, it is required to remove it from the
weighing chamber.
CAUTION!!!
Cleaning of the pan when assembled may cause damage of the measuring
system of the balance.
4.6. Plugging to mains
Balance can be plugged to mains only with a power adapter that comes
standard with the balance. Nominal power supply of the power adapter
(specified on the data plate of the power adapter) should be compatible to the
power from mains.
Plug the balance to mains – the plugging socket is located at the back of balance’s
housing. Balance display will light and show name and number of software, after
which balance will display 0.000g (for balances with resolution 1mg) or 0.00g (for
balances with resolution 10mg).
If indication is other than zero, press ZERO/TARE key.
Before unplugging the balance from mains it is obligatory to switch off the display
by pressing ON/OFF key on balance’s overlay.
4.7. Connecting peripheral devices
The balance must be unplugged from the mains before connecting or disconnecting
any peripheral
devices (printer, PC computer). Use only peripheral devices
recommended by the manufacturer with your balance. These have been ideally
coordinated to your balance. On connecting a peripheral device, plug the balance to
mains.
- 11 -
5.
BASIC FUNCTIONS
Balance PS/X series enables determining mass in the following measuring units:
Fig. 2. Measuring units
Apart from determining mass of weighed object using different measuring units, the
software balance PS/X series comprises the following working modes:
−
−
−
−
−
−
−
−
Parts counting
Checkweighing
Dosing
Percent setup
Animal weighing
Determining density of solids and liquids
Formulation
Statistics from completed measuring series
Both the measuring units and the working modes can be set as inaccessible in the
user menu. This option is implemented for the purpose of adjusting balance to user needs
and requirements, i.e. providing access only to those functions and units which are
required by a user.
Determining accessibility attribute of a working mode / measuring unit is set in
balance’s menu and it is described further in this user manual.
- 12 -
6.
DESCRIPTION
6.1. Graphic display
Fig. 3. Balance graphic display
1.
Mass indication of weighed load or counted parts,
2.
Measuring unit,
3.
Pictogram denoting whether measurement result is stable,
4.
„BARGRAPH” presenting which part of accessible measuring range is in use,
5.
Text informing on enabled working mode,
6.
Current date,
7.
Current time,
8.
Pictogram denoting, that the indication is in precise ZERO point.
- 13 -
6.2. Keyboard
Each button of the balance’s keyboard operates as a dual-function key, i.e. it can either
carry out a specific function or be used to move in balance’s menu structure.
ON/OFF key enables switching on and off balance’s display. If
switched off balance components other than the display are
powered, and balance is in stand-by mode.
F key. Function key, which enables quick entering the settings
of an active working mode
MODE key for selecting balance’s working mode.
UNITS key, changes measuring units.
PRINT/ENTER key - Sends current display status to a
peripheral device (PRINT) or accepts selected value of a
parameter or function (ENTER).
ESC/ZERO TARE key – zeroing / tarring of balance’s
indication.
Adjustment – function key of immediate initiating the
adjustment / calibration process.
Function key for entering the main menu of a balance.
Navigating arrows for moving in balance’s menu or changing
parameter value
- 14 -
6.3. Sockets and interfaces
1.
2.
3.
4.
5.
Power supply socket
Keyboard PS/2 type socket
USB port (only in non legalization
balances)
RS 232 socket
Additional display socket
Fig. 4. Interfaces of a balance PS/X series
7.
USER MENU
User menu of a balance PS/X series consists of 9 main menu groups named using letter P
and a corresponding number. The name and content of the menu is presented below.
P1 Adjustment
01 Internal adjust.
02 External adjust.
03 User adjust.
04 Adjustment test
05 Weight correction
06 Automatic adjust
07 Auto adjust. time
08 Report printout
|********|
|********|
|********|
|********|
| * * * * * *0.0 |
| * * * * * *0.3 |
| * * * * * *0.3 |
| * * * * * *0.1 |
P2 GLP
01 User
02 Project
03 Print time
04 Print date
05 Print user
06 Print project
07 Print Id
08 Print adjustment
09 Print adjust diff.
| Smith John |
| AR – 65/04 |
| * * * * * * 0 | no
| * * * * * **. 0 | no
| * * * * * * * 0 | no
| * * * * * * * 0 | no
| * * * * * * *.0 | no
| * * * * * * *.0 | no
| * * * * * ** .1 | yes
P3 Date/Time
01 Date format
02 Time format
03 Time
04 Date
05 Display time
function
function
function
function
both
3 hours
yes
| * * * * * * * 0 | D/M/R
| * * * * * * * 0 | 24 hours
| * * * * * * * * | function
| * * * * * * * * | function
| * * * * * * * 1 | yes
- 15 -
06 Display date
P4 Readout
01 Filter
02 Value release
03 Display refresh
04 Autozero
05 Last digit
06 Negative
07 Environment
| * * * * * * * 1 | yes
| * * * * * * * 3 | normal (average)
| * * * * * * * 1 | fast+reliable
| * * * * * * * 1 | 0.08 s
| * * * * * * * 1 | yes
| * * * * * * * 1 | always
| * * * * * * * 0 | no
| * * * * *0.1 | stable
P5 RS - 232
01 Interface
02 Baud rate
03 Parity
04 Data bits
05 Stop bits
06 Automatic printout
07 Interval
08 Min. mass
09 Print stable
10 Printer type
11 Paper cut
12 Erase statistics
| * * * * * * * 0 | RS 232
| * * * * * * * 1 | 4800
| * * * * * * * 0 | no
| * * * * * * * 2 | 8 bits
| * * * * * * * 1 | 1 bit
| * * * * * * * 0 | no
| * * * * * * * 1 | * 0.1 s
| * * * * * * * 4 | 10 d
| * * * * * * * 1 | yes
| * * * * * * * 0 | standard
| * * * * * * * 0 | no
| * * * * * * * 0 | no
P6 Printout
01 Printout no.
02 Printout 1 start
03 Printout 1 stop
04 Printout 2 start
05 Printout 2 stop
... . . . . . . . . . .
10 Printout editing
11 String 1
11 String 2
... . . . . . . . . . .
90 String 80
| * * * * * * * 0 | standard
|*******1|
|*******1|
|*******1|
|*******1|
|*******0|
| * * * * * * * * | function
|*******1|
|*******4|
|*******1|
|*******0|
P7 Units
01 Grams
02 Milligrams
03 Carats
04 Pounds
05 Ounce
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
- 16 -
06
07
08
09
10
11
12
13
14
15
16
Ounce troy
Dwt
Taele Hk.
Taele S.
Taele T.
Mommes
Grains
Newton
Tical’ e
Custom unit
Custom unit coef.
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
|
1.0 |
P8 Working modes
01 Parts counting
02 Checkweighing
03 Filling
04 Percent setup
05 Animal weighing
06 Density
07 Formulation
08 Statistics
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
| * * * * * * * 1 | yes
P9 Other
01 ID setting
02 Autom. ID print
03 Beep
04 Language
05 Backlight
06 Brightness
07 Contrast
08 Screen saver
09 Temperature
10 Factory no.
11 Software no.
12 Parameter printout
13 Upload parameters
14 Password protect
| * * * * * * * * | function
| * * * * * * * 0 | no
| * * * * * * * 1 | yes
| * * * * * * * 1 | English
| * * * * * * * 1 | yes
| * * * * * * * * | function
| * * * * * * * * | function
| * * * * * * * 0 | no
| * * * * * * * * | function
| 114493 * * * |
| MBS w.04 |
| * * * * * * * * | function
| * * * * * * * * | function
| * * * * * * * * | function
- 17 -
Parameters type in the user menu:
•
•
•
function – having a specific operation, e.g. balance adjustment
selectable – enables selecting one of a few available values, which are
permanently set in balance’s memory, like: display refreshing, screen saver,
determining availability of a measuring unit or a working mode.
Enabling data entering – balance user can enter a value of a parameter, e.g. set
date, time, user no, strings (texts) in a printout.
Balance menu on the display – graphic presentation
While in the weighing mode press SETUP key. The display opens balance’s main menu
(display I). Press UP or DOWN navigating arrows on the balance’s overlay to move the
cursor upwards or downwards in the menu content. Place the cursor next to a menu option
to be previewed. Press RIGHT ARROW navigating key on balance’s overlay to open the
submenu content (display II).
Fig. 5. Balance menu
1 – balance menu no.
2 – cursor for selecting a menu option
3 – menu content name
4 – name of selected menu option (setting)
5 – submenu number
6 – submenu name
7 – attribute set for a submenu option
8 – value (description) of an attribute set a submenu option
- 18 -
7.1. Moving through the menu
Moving in the user menu can be carried out using:
Balance keyboard,
External PC keyboard PS/2 type connected to balance’s socket,
Commands sent from a connected computer to a balance
7.1.1. Moving through user menu using a balance keyboard
Setup key. Entering balance’s main menu
Moving the cursor down in the menu list
Moving the cursor up in the menu list
Selecting submenu for activating. On pressing the key, the display
indicates the content of a selected group.
Exit to previous menu level, e.g. to main menu
Esc/TARE key. Abandon parameter changes
7.1.2. Return to weighing mode
Changes introduced in balance memory will be saved on returning to
weighing with procedure of saving changes. Press ESC key for a few times
until the display shows a question: Save? As displayed, select one of
available options:
ENTER
ESC
– save changes and go back to menu;
– abandon changes and go back to menu.
Fig. 6. Return to weighing mode
- 19 -
7.1.3. Moving through user menu using external computer keyboard PS/2
type
Al keys and buttons located on balance’s overlay have their equivalents on a computer
keyboard PS/2 type. See below table for reference:
- equivalents of function keys
Description
ON/OFF key enables switching on and off
balance’s display
Function key for entering the main menu of a
balance
Selecting balance’s working mode, e.g.:
animal weighing
Selecting measuring unit
PRINT key
TARE key
- equivalents of navigating arrows
Moving the cursor up in the menu list
Exit to higher level in menu structure , e.g. to
main menu
Entering settings of a selected submenu.
Moving the cursor down in the menu list
- 20 -
Key on
balance’s
overlay
- equivalents of ENTER / PRINT key and ESC key
Accepting entered value of a parameter
Abandon parameter changes and exit to to main
menu
7.1.4.
Moving through user menu using virtual keyboard, via RS 232
interface
Most of the functions controlled or set using keys on balance’s overlay or an external
computer keyboard PS/2 type can be carried out by a set of commands sent from a
computer to a balance.
The commands enable moving through user menu, setting parameters or controlling
balance operation. The list of commands is provided at the end of this user manual.
7.2. User menu - content
The content of balance’s menu is presented in point 6 of this user manual.
Menu structure of a balance PS/X series is described in point 5 of this user manual. When
in the main weighing window press Setup key to enter the main menu settings. The display
opens a list with main menu. By pressing up and down navigating arrows move the cursor
and place it next to a submenu to be edited.
Fig. 7. Balance main menu – submenu selection
In order to edit a submenu, press RIGHT ARROW key, which opens the content of
selected submenu. When inside the submenu structure, the user can select an option to be
edited (modified) by placing the cursor next to submenu name (use up and down
navigating arrows). When the cursor is placed next to desired option press RIGHT
ARROW key to enter submenu settings.
- 21 -
Balance reactions for above procedure:
-
A specific process (e.g. balance adjustment) which is carried out in a submenu
described as a function;
Editing an attribute of a submenu (flickering digit of a submenu setting enables
changing parameter value of entering a sequence of characters)
Fig. 8. Balance submenu – selection buttons
- 22 -
8.
WEIGHING
Basic working conditions for obtaining reliable measurement results:
- Stable and constant temperature in a weighing room,
- Stable foundation of a balance,
- Selecting adequate balance settings adjusted to ambient conditions at a
workstation.
Before start of weighing process or in case of essential change of ambient
conditions at a workstation (e.g. ambient temperature change at a workstation more
than 1°C/h) the balance requires adjusting. The procedure of balance adjustment is
described in point 9.1 of this user manual.
Before start of weighing procedure, it is recommended to load the balance’s
weighing pan a few times with mass close to balance max capacity, Check if
unloaded balance indicates “precise zero”
(the pictogram is visible on in the
upper left corner of balance’s display) (and only if parameter P4 06 Autozero is set
to 1: yes) and whether measurement is stable –
(the pictogram is visible in the
upper right corner of the display. If the mass indication is other than zero, press
zeroing key
If the working conditions are unfavourable (i.e. unstable measurement result), then
the display previews dashes (horizontal lines). After exceeding a preset amount of
time for zeroing the indication, the balance returns to weighing mode without zeroing
the indication. In such case the user should wait for stabilization of working
conditions and once again press →0/T← key.
Press Units key to set a measuring unit. Place weighed object on balance’s
weighing pan and read the result only on stabilization of the measurement. If the
measuring unit is not displayed on pressing the Units key, then go to the
corresponding submenu and check the accessibility attribute of the measuring unit.
Mass indication of a load placed on balance’s weighing pan can be zeroed for
multiple times. Pay attention not to exceed maximal capacity of a balance by
applying multiple zeroing function.
During times between carrying out the following measurement series do not unplug
the balance from mains. It is recommended to switch off balance’s display by
pressing ON/OFF key. On repeated pressing of the ON/OFF key the balance is
ready for operation and does not require thermal stabilization.
A balance PS 200/2000/X is a dual range instrument. The accuracy of the I weighing
range is d1=0.001g, and of the II range is d2=0.01g.
- 23 -
Fig. 9. Dual range balance – measurement result in the I weighing range
Transmission from weighing with the accuracy of the I weighing range to the accuracy of
the II weighing range takes place automatically on exceeding Max1 point i.e. 200g. The
moment of entering into weighing with the accuracy of the II weighing range is signaled on
balance’s display by a pictogram II located on the right side of the display and an additional
tags over the last but one digit.
Fig. 10. Dual range balance – measurement result in the II weighing range
From now on the balance measures mass of weighed loads with the accuracy of the II
weighing range.
Fig. 10-1. Dual range balance – measurement result in the II weighing range
In order to return to weighing with the accuracy of the I weighing range:
•
Take the weighed load off the weighing pan
Fig. 10-2. Dual range balance – measurement result in the II weighing range
- 24 -
•
When the indication returns to zero and pictograms: →0← and
(precise
zero point and stable measurement) light up on the display, press →0/T← key
Fig. 10-3. Dual range balance – measurement result in the I weighing range
The balance returns to weighing with the accuracy d1=0.001g and the pictogram of the II
weighing range and the tag over the last but one digit are blanked.
8.1. User log in function
The users of a balance PX/X series can have their specific access code to the balance’s
menu. The password system is determined by balance’s administrator, i.e. a user of the
higher order in relation to the other balance users. The access password can comprise up
to 6 digits.
Balance software enables determining:
•
A single Administrator, who has access to all balance settings and software
functions, including changing the password of the administrator and other users.
•
A single User who is authorized to access balance settings and functions, as set
by the balance administrator.
Setting passwords and access levels
•
•
•
•
Remember, that after the first entering the password settings (see parameter P9
14 Password protection), the user should set a password for the balance
Administrator.
The software requires inserting an administrator password when entering
parameter P9 14 Password protection only if the administrator password is other
than “0”.
On the following entering this parameter, the software will require inserting the
administrator’s password. Access to parameter settings of submenu P9 14
Password protection will be granted only on entering correct password.
Unless the password is correct, the balance displays a message on incorrect
password and goes back to displaying previous screen.
Depending on the settings, the inserted password is previewed either as a
sequence of digits or as asterisks (the initial value of each entered digit is always
= 0)
Following the point 6.1.1 menu P9 Other contains the following options:
- 25 -
Fig. 11. Password – function activating
Fig. 11-1. Password protection – menu content
- Administrator
the field for inserting administrator’s password. Balance administrator has access to
all balance functions and settings
- User
the field for inserting user’s password, Balance user has access to the functions and
settings which attribute is set to YES (password protection) and to other balance
settings and functions
- Startup
if the option is set to YES, then on balance startup the software requires entering a
password
- Functions
if the option is set to YES (password protection), then use of functions other than
weighing is accessible only on entering a password (of an administrator or a user)
- Settings
if the option is set to YES (password protection), then changes to the balance settings
can only be carried out on entering a password
- Cal + GLP only
if the option is set to YES, then a user is authorized (with no need to enter a
password) to carry out adjustment / calibration procedure and change settings in the
submenu P2 GLP. Changes of any other balance settings require entering a
password.
- Asterisk
if the option is set to YES , then on balance startup the entered password is
previewed in a form of asterisks.
- 26 -
Entering Administrator’s password
Enter a password for the balance administrator (a sequence of 6 digits) and for the
user. Balance administrator has full access to balance menu. The user access is
limited to the one described in previous point (balance menu, startup, adjustment, etc.
options can be attributed YES/NO).
It is very important to remember the password, as if option “password on startup” is
enabled (set to YES), then on the following plugging the balance to mains, the
software will request for entering the password. If it is entered incorrectly, then balance
operating will be blocked.
While entering the password use balance keys presented on Fig. 2 or use external
keyboard PS/2 type connectable to balance’s socket.
Set accessibility criterion to other balance settings and functions, depending on
access level required by the balance user.
Fig. 12. Keys on balance overlay – entering values while editing fields of balance
menu
- 27 -
9.
BALANCE ADJUSTMENT
In order to ensure the highest measuring accuracy, it is recommended to periodically
introduce to balance memory a corrective factor of indications in relation to a mass
standard – i.e. balance adjustment.
Adjustment should be carried out:
- Before the beginning of a weighing procedure,
- If long breaks between following measuring series occur
- If temperature inside the balance changes more than: 1°C within last hour
Types of adjustment
Internal automatic adjustment
* triggered by temperature change
* triggered by elapsing time
Manual internal adjustment
* initiated from balance’s keyboard (triggered by pressing CAL key)
Adjustment with an external weight
* with declared mass which cannot be modified
* with optional mass which needs to be specified before process initiation
Caution:
In case of verified balances only the automatic internal adjustment and manual internal
adjustment systems are available for a user.
Remember to perform the adjustment when there is no load on the pan!
9.1. Automatic balance adjustment
Activation of automatic internal adjustment is triggered on:
Elapsing a specified amount of time from last carried out adjustment process, or
Ambient temperature changes by a value specified by the balance manufacturer
On recognizing any of the above case, balance’s display shows the following message
box.
Fig. 13. Automatic internal adjustment – display content
The time delay enables the user to take the weighed load of the weighing pan, if a
weighing process is in progress. Pressing T/O key causes temporary delay of the
adjustment process initiation. In approximately 5 minutes the needs for adjustment is
triggered once again.
- 28 -
Automatic adjustment settings
Fig. 14. Settings of automatic balance adjustment
1 – main menu number
2 – marker of selected function
3 – function name
4 – name of an active function / mode / process
5 – selecting factor triggering auto-adjustment process (time / temperature)
6 – determining time interval between the following auto-adjustment
processes
7 – value of set auto-adjustment triggering factors
8 – value of set time interval between the following automatic adjustment
processes
Changing the values of automatic adjustment triggering factor and automatic adjustment
time causes changes in description of the above fields (fields in fig no. 9 and 10).
01 Internal automatic adjustment
Initiates internal automatic adjustment process, which is carried out fully automatically
with no operator’s activity. If balance’s weighing pan is loaded, then the balance
displays a command ordering unloading it.
02 External adjustment
Adjustment process carried out with an external weight, which value is saved in
balance’s memory. The function is disabled in verified balances.
03 User adjustment
Adjustment process carried out with an optional weight. Mass of the weight is specified
before process initiation. The function is disabled in verified balances.
- 29 -
04 Adjustment test
Mass comparison of internal adjustment weight with its value saved in balance memory
05 Internal weight correction
The function enables correcting the value of internal adjustment weight. The function is
disabled in verified balances
06 Automatic adjustment
Determination of factors triggering start of automatic internal adjustment:
0
no
– none of factors will cause start of adjustment
1
time
– adjustment triggered by time interval set in point 07
2
temperature – adjustment triggered by change of temperature
3
both
– adjustment triggered by time and temperature
Function not available in verified balances.
07 Time of automatic adjustment
Determination of time interval, after which automatic adjustment process is initiated.
Function not available in verified balances.
Return to weighing mode
Changes introduced in balance memory will be saved on returning to
weighing with procedure of saving changes. Press ESC key for a few times
until the display shows a question: Save? As displayed, select one of
available options:
ENTER – save changes and go back to menu;
ESC
– abandon changes and go back to menu.
(see point 7.1.2. Return to weighing)
- 30 -
9.2. Adjustment test
Adjustment test is a comparison of internal adjustment weight with its value stored in
balance’s memory. This process is carried out automatically and its result is shown on the
display.
Fig. 15. Adjustment test
Cal. – the value of internal adjustment weight
Curr. – weighing result of the internal adjustment weight
Dev. – deviation calculated between the both values
Return to weighing mode
Changes introduced in balance memory will be saved on returning to
weighing with procedure of saving changes. Press ESC key for a few times
until the display shows a question: Save? As displayed, select one of
available options:
ENTER – save changes and go back to menu;
ESC
– abandon changes and go back to menu.
(see point 7.1.2. Return to weighing)
9.3. Manual adjustment
9.3.1. Internal adjustment
Press CAL key on balance’s overlay, or
1.
2.
3.
4.
5.
Go to submenu P1 – Adjustment.
Place the marker next to a function 01 Internal adjustment.
Press RIGHT ARROW KEY.
The balance automatically carries out internal adjustment process. While
adjustment process is in progress do not load the weighing pan with any weight.
On completing the internal adjustment procedure the balance saves adjustment
data in its memory and returns to weighing mode.
Caution:
In order to abort adjustment process press ESC key.
If during internal adjustment process the weighing pan is loaded, then the
balance displays an error message. The adjustment process is automatically
stopped. On taking off the load from the weighing pan, the process is resumed
and completed.
If the DRH function is enabled in balance settings, then balance user cannot
abort the adjustment process once initiated.
- 31 -
9.3.2. External adjustment
The external adjustment in balances PS/X series should be carried out with an external
mass standard / weight class: F1
1.
2.
3.
4.
5.
6.
7.
8.
Go to menu P1 – Adjustment.
Set the marker next to a function 02 External adjustment.
Press RIGHT ARROW KEY.
The software displays a command to take off any load from the weighing pan (the
weighing pan must by empty). On unloading the weighing pan, press ENTER key.
The balance determines mass of an empty weighing pan.
Load a weight / mass standard which mass is given on the display and press
ENTER key.
On completing adjustment process the balance returns to displaying submenu P1
- Adjustment
Return to weighing mode – in accordance with point 7.1.2.
If the DRH function is enabled in balance settings, then external adjustment
process is disabled. The DRH function is enabled in verified balances (which are
subject to conformity assessment.
9.3.3. User adjustment
The external adjustment in balances PS/X series should be carried out with an external
mass standard / weight class: F1
- Go to menu P1 – Adjustment and set the marker next to a function 03 User
adjustment.
- Press RIGHT ARROW KEY.
- The balance displays a command to enter mass of an adjustment weight. The first
digit of the weight value is flicering, and it is ready for editing.
Fig. 16. User adjustment – declaring weight value
- Use function kwys (as specified in point 6.1.1 of this user manual) to enter the value
of the external weight/mass standard.
- Accept the weight’s value as entered. The balance initiates adjustment process by
indicating process commands on the display.
- The balances shows a command on determining mass of the empty weighing pan,
which is followed by a command to place a weighed with pre-determined mass.
- 32 -
- On placing the determined weight on the weighing pan accept it by pressing Enter
key.
- On completing adjustment process the balance returns to displaying submenu P1 Adjustment.
- Return to weighing mode – in accordance with point 7.1.2.
It is recommended that the mass of an external adjustment weight is
approximately ¾ of balance’s maximum capacity.
If the DRH function is enabled in balance settings, then external adjustment
process is disabled.
9.4. Adjustment report printout
On completion of any type of adjustment process, the balance enables preparing a report
from adjustment process. The report can be printed on a connected printer and sent to a
computer and saved in a form of file for records.
P1 08 Report printout :
P1 08 Report printout :
1: yes
0: no
– report printout enabled
– report printout disabled
Remember, that if the parameter is set for 1 (YES), then a report is generated and sent
automatically.
Fig. 17. Submenu: Adjustment
The content of the report from adjustment process depends on settings of GLP
parameters. Any option in the GLP submenu which attribute is YES is included in a report
from adjustment process.
- 33 -
Fig. 18. Submenu GLP - settings
Apart from information set in menu group the report contains: type of completed
adjustment process (description Calibration:) and deviation from the adjustment process
(description Deviation:).
Fig. 19. An example of a report from adjustment process
- 34 -
10. DETERMINING CONTENT OF A PRINTOUT FOR GLP PROCEDURES
Menu P2 GLP is group of the parameters which enables declaring variables that are
present on a printout from adjustment process. Fields referring to:
- user (max 8 alphanumeric characters)
- project (max 8 alphanumeric characters)
are editable are enable entering a text using balance’s keyboard or connectable external
computer keyboard PS/2 type. The other fields listed in the GLP are set:
- 1
yes (print on a report)
- 0
no (do not print on a report)
The content of submenu GLP is provided in point 8 of this user manual.
For the purpose of more convenient moving in the user menu and changing menu settings
it is recommended to use external computer keyboard PS/2 type.
11. DATE AND TIME SETTINGS
The balance PS/X series features an internal real-time clock, and its parameters are
editable. Go to submenu P3 Date/Time following prompts given on below figure.
FIg. 20. Submenu Date / Time
01 Date format
Enables two types of setting date format:
- 1
date format
Month/Day/Year
- 0
date format
Day/Month/Year
On selecting appropriate date format accept it by pressing ENTER key.
02 Time format
Enables two types of setting time format:
- 1
time format
12 hours
- 0
time format
24 hours
- 35 -
On selecting appropriate time format accept it by pressing ENTER key.
12 hour time format is differentiated by letters PM or AM present on printouts.
03 Time
Press RIGHT ARROW KEY to enter parameter 03 Time, as presented on below figure.
Fig. 21. Submenu Date / Time – time setting
Place the marker next to a value to be edited (Hour, Minute, Second). Activate a field for
editing by pressing RIGHT ARROW KEY. Press UP and DOWN ARROWS to set numeric
values of hour / minute / second.
Fig. 22. Submenu Date / Time – time setting – controlling keys
Accept set value (the last digit stops flickering).
Repeat the activity for other time values. On setting the new time value press ENTER key.
The balance returns to displaying submenu P3 Date/Time. The time value visible in the
upper bar graph of the display is changed.
On setting required time value return to weighing mode as specified in point 7.1.2 of this
user manual.
- 36 -
04 Date
Press RIGHT ARROW KEY to enter parameter 04 Data. As specified in the previous point
(03 Time) set current date. On setting required date return to weighing mode as specified
in point 7.1.2 of this user manual.
Fig. 23. Submenu Date / Time – date setting
05 Display time
Available settings
1 – YES time displaying enabled, the upper bargraph of the display contains time,
0 – NO time displaying disabled.
06 Display date
Available settings
1 – YES date displaying enabled, the upper bargraph of the display contains date,
0 – NO date displaying disabled.
Return to weighing mode
(see point 7.1.2. – Return to weighing mode)
- 37 -
12. SETTING BALANCE OPERATING PARAMETERS
Balance PS/X series, in menu group <P4 Readout> enables adjusting balance operation
to current ambient conditions at a workstation (filter) and required user needs (display
refreshment, autozero, displaying last digit).
Fig. 24. Submenu Readout – internal settings
12.1. lter settings
Depending on the ambient conditions at a workstation, the balance enables setting the
filtering value. In case of very good operating conditions it is recommended to set the
filtering value to very fast (parameter value 01 Filter set to 1). If the operating conditions
are harsh (air drafts, vibrations) set the filter to slow or very slow (parameter value 01 Filter
set to 4 or 5). The effectiveness of filter operation differs in relation to the measuring range.
The filter operates with lower accuracy while the mass indication is quickly increasing after
placing a load on the weighing pan. Filter accuracy is increased when weighed mass is
within filter’s set operation range (parameter: filter operation range is available only in
balance’s service menu, and it is inaccessible for the user). Depending on filter settings the
weighing time is either shorter (low filter values) or longer (high filter settings).
12.2. Value release
Select one of available value release options: fast, fast+reliable or reliable. Depending on
accepted criterion the weighing time will be shorter or longer.
12.3. Time interval of display refreshment
The parameter determines time interval in which display indication is refreshed.
In case of the higher refreshment values, the display does not indicate intermediate and
unstable mass values occurring while loading and unloading weighed mass on the
weighing pan. For low refreshment values the display indicates any changes in the value
of weighed mass – which is required while dosing loose or liquid materials. The time
interval of display refreshment is set in seconds.
- 38 -
12.4. Autozero function
Dla zapewnienia dokładnych wskazań wagi wprowadzono programową funkcję
„AUTOZERO”. Zadaniem tej funkcji jest automatyczna kontrola i korekta zerowego
wskazania wagi.
If AUTOZERO function is enabled, then each weighing process starts from precise zero
point. There are, however, some cases when this function can be a disturbing factor of
measuring process; for instance very slow placing of a load on the weighing pan (e.g. load
pouring) – in such case system of zero indication correction can also correct actual
indication of loaded mass. AUTOZERO function is enabled or disabled in parameter P4 03
as specified in point 6.1.1 of this user manual.
12.5. Last digit
In order to ensure adequate operating comfort with a balance, the user can determine
presence of the last digit on the display and criteria of its displaying.
Available settings are:
0
never
1
always
2
when stable
12.6. Negative
The function aids previewing mass value and other indications on the display. Depending
on user needs it is possible to enable or disable the function.
12.7. Operating conditions
This parameter enables two settings: stable or unstable. Setting the parameter to stable
causes much faster operation of the balance, i.e. the weighing time is shorter than
compared to setting: unstable. This parameter refers to operating and ambient conditions
at a workstation. If the conditions are unstable, then it is recommended to set the
parameter to unstable. The default setting of the parameter is: stable.
- 39 -
13. RS 232 FUNCTIONS
Balance PS/X series enables defining parameters of balance communication with a
computer or a printer.
Fig. 25. Submenu RS 232 - settings
01 Interface
02 Baud rate
03 Parity
04 Data bits
05 Stop bits
06 Handshake
07 Automatic printout
08 Interval
/ 0 : RS232
1 : USB*
2 : RS232+USB*
/ 0 : 2400
1 : 4800
2 : 9600 3 : 19200
/ 0 : no
1 : even
2 : odd
/ 1 : 7 bits
2 : 8 bits
/ 1 : 1 bit
2 : 2 bits
/ 0 : no
1 : RTS/CTS
2 : XON/XOFF
/ 0 : no
1 : continuous 2 : with interval 3: when stable
the interval determines the period of time in which the
balance sends display indication to a printer/computer. The
interval is set according to a relation x 0.1 s = interval time).
The available range of the parameter setting from 1 to 9999.
09 Min mass
Minimamum mass for enabling automatic operation of the
RS 232. The following measurement data is sent only if
taking off the load the mass indication returns below the set
value mininum threshold
10 Print stable
0 : no
1 : yes
11 Printer type
Epson or standard
12 Paper cut
Available only in EPSON printers featuring this function. If
the function is set to YES then paper cut option is carried out
automatically.
13 Clear stat.
/0: no
1: on header
2: on footer
The option is enabled in <STATISTICS> mode, where the
header is printout no.1, and the footer is printout no. 2.
Means of designing the printouts and operation of
<STATISTICS> mode is described further in this user
manual.
* - only in non legalization balances
On setting appropriate parameter values return to the weighing mode in accordance with
point 7.1.2. of this user manual.
- 40 -
14. PRINTOUTS
Printouts menu is dedicated for creating non-standard printout templates and selecting
type of a printout which is printed. Detailed description of non-standard printouts is
provided in point 19. of this user manual.
15. SETTING ACCESSIBILITY OF MEASURING UNITS
This group of parameters enables setting accessibility of measuring units, which are
available for an operator after pressing the Units key on balance’s overlay.
All measuring units which attribute is set to
1: yes
are accessible from the main menu level under a key for toggling between the measuring
units.
The measuring units described as 09 Taele Hk., 10 Taele S., 11 Taele T . the following
relations occur:
•
If the attribute of all three measuring units is set to 1: yes, then the software will
display only the first one, i.e. 09 Taele Hk
•
If the measurement should be carried out using 11 Taele T unit, then the attribute
of the other two units should be set to 0 : no
Enter group of parameters P7 Units.
Fig. 26. Measuring units - settings
After setting the required parameter values return to weighing mode in accordance with
point 7.1.2. of this user manual.
Caution:
In case of verified balances the available measuring units are limited to: [g], [mg], [ct] –
even if set to 1 – YES in balance’s menu
- 41 -
16. SETTING ACCESSIBILITY OF WORKING MODES
This group of parameters enables setting accessibility of working modes, which are
available for an operator after pressing the Mode key on balance’s overlay.
Fig. 27. Working modes - settings
All working modes which attribute is set to 1: yes are accessible from the main menu level
under a key for toggling between the working modes. Changes to the parameter values are
carried out in accordance with point 7.1.1 of this user manual.
- 42 -
17. OTHER PARAMETERS
Depending on user needs the balance enables setting parameters influencing its operation.
These parameters are grouped in menu P9 Other, for instance: beep sound on pressing a
key/button, screen contrast, etc. Enter submenu P9 Other to change its settings.
01
ID settings
The submenu contains 6 codes each comprising 6 digits. The codes are used in
printouts for specifying a product, operator, product batch, etc.
02
Automatic ID Printout
If set to YES, then it prints all numeric codes. If set to NO, then the codes are not
printed.
03
Beep sound
Determines whether each pressing of a key/button on balance overlay is confirmed by
a beep sound, available settings: YES/NO.
04
Language
Selecting language version of software menu, available settings Polish or English
05
Backlight
Determines whether the backlight of the balance’s graphic display should be enabled
or disabled (enabling the backlight option improves data visibility on the display)
06
Screen brightness
Enables changing the brightness of the balance’s graphic display – entering the
function opens a window for setting brightness level using buttons on the balance’s
overlay
07
Screen contrast
Enables changing the contrast of the balance’s graphic display – entering the function
opens a window for setting contrast level using buttons on the balance’s overlay
08
Screen saver
Switching on the screen saver causes blanking displayed values after a set amount of
time. The indication on the display does not change while blanking.
09
Temperature
This function serves for information purpose only, and it enables previewing
temperature value that is measured inside the balance by a sensor. Return to menu
by pressing ESC key.
10
Balance no.
This function serves for information purpose only, and it enables previewing factory
number of a balance.
11
Software no.
Enables previewing number of software revision operating in a balance.
- 43 -
12
Parameter printout
Enabling this function causes printing balance parameters set in the user menu. The
user specifies numbers of parameters that should be printed.
Fig. 28. Submenu Other - parameter printout
On entering this option and selecting user settings, the balance starts sending current
parameter values to a connected printer via RS 232 interface.
13
Acquire (upload) parameters
Enabling this function causes uploading all parameters sent via RS 232 interface from
a connected computer. On completing uploading process the balance informs a user
on number of accepted and changed parameters, and number of incorrectly declared
parameters which are rejected by the balance. Printing and uploading balance
parameters is a very simple and intuitive means of setting new values of balance
parameters. On printing to a file current parameter values on a connected computer,
the user can simply and quickly change parameter values. After saving made
changes, the updated file is sent from the computer level to balance’s software. On
completing of uploading process and saving changes the balance accepts new
parameter settings. The procedure requires that a user is familiar with balance
parameters and has good knowledge of computers.
14
Password protection
This submenu enables setting a password limiting access to a balance for an
Administrator and a user (see point 8.1. of this user manual: USER LOG IN)
- 44 -
18. WORKING MODES
18.1. Parts counting of the same mass
The parts counting mode can be carried out suing three means:
- inserting mass of a single part
- determining mass of a single part from a standard quantity
- selecting a part for counting from balance’s database
18.1.1. Counting by inserting mass of a single part
Activate parts counting mode.
Fig. 29. Parts counting – main menu
Set reference mass and press ENTER key or move the cursor next to the field 07 Run and
press RIGHT ARROW KEY. The display indications change to specific for the parts
counting mode.
Fig. 30. Parts counting – display content
APW
WGH
pcs
– mass of a single part [g]
– mass of all parts placed on balance’s weighing pan
– marker of the parts counting mode
- 45 -
Return to weighing mode
Press MODE key, the display indicates list of available
working modes
move the cursor next to a field: MO Weighing
Press RIGHT ARROW KEY, the software returns to weighing mode and
displays current measurement result
18.1.2. Counting by determining mass of a single part from a standard
quantity
Enable parts counting mode regardless on mass that has to be specified in field 01. Move
the cursor next to a field 07 Run and press RIGHT ARROW KEY. While in parts counting
mode press F key. The display opens a window for specifying standard quantity of counted
parts (fields 01 – 04) or set the standard quantity in field 05 – Sample.
Fig. 31. Counting by determining mass of a single part from a standard
quantity
Next, press RIGHT ARROW KEY and follow commands presented on the display.
Fig. 32. Display content with enabled AAC function
123-
mass of a single part
mass of all counted parts
the pictogram of enabled Automatic Accuracy Correction function
- 46 -
The display indicates mass of counted parts, that are loaded on balance’s weighing pan
(i.e. 10 parts). If the added amount of parts is below the currently counted one, then the
software automatically corrects mass of a single part. In this case it is APW = 5.2282
corrected to 5.1837. from now on the following parts are counted according to the new
mass of a single part.
This means enables counting mass of a single part from a standard quantity.
The software comprises four conditions for operation of
Automatic Accuracy Correction function
1.
2.
3.
4.
After adding the number of parts placed on balance’s weighing pan must be
greater than before adding
After adding the number of parts loaded on balance’s weighing pan must be less
than twice the quantity which was indicated on the display before adding
current quantity of parts must contain within a tolerance ± 0,3 of the total value,
stable measurement result.
If a user claims, that standard quantity is sufficient, it is possible to save the mass of a
single part in balance’s memory by pressing RIGHT ARROW KEY on balance’s overlay.
Fig. 33. Automatic Accuracy Correction – saving single part mass in the
database
Set the cursor next to a desired field and insert name for weighed parts. Press Enter key
(for saving the name) and Enter key (for saving the value). Next to the inserted name there
is mass of a single part. Now the record in the database is ready for recalling by using field
02 Recall standard.
- 47 -
18.1.3.
Selecting a part for counting from balance’s database
Enable parts counting mode in accordance with below figure.
Fig. 34. Selecting a part for counting from the database
Select a record from the database, and start part counting process.
18.2. Checkweighing
Checkweighing is a process intended for precise determining mass of a weighed sample
with set and enabled checkweighing thresholds (limits). The thresholds are to visualize (by
means of a bargraph located on the left side of the display) and monitor checkweighing
process.
Mode activating
FIg. 35. Checkweighing – mode activating
- 48 -
Display content
Fig. 36. Checkweighing – display content
1 – measurement result
2 – bargraph
3 – working mode name
4 – difference between mass of weighed sample and the center of the tolerance field
(HI/LO)
5 – the values of low (LO) and high (HI) checkweighing thresholds
6 – a pictogram indicating the weighing range of currently weighed sample
(available indications: LO, OK and HI).
Remember to set the 02 Hi Threshold first, as the software automatically checks
whether inserted values are correct and hold within the measuring range of a
balance.
If set values are recognized by the software as incorrect, the balance displays an error
message and returns to parameter settings without saving changes.
Checkweighing with use of database of thresholds (limits)
Checkweighing process can be carried out with use of the DATABASE OF THRESHOLDS,
which is a programmable collection of records comprising:
− 500 records
− Name of a product in each record (max 10 alphanumeric characters)
− The value of HI threshold for each record
− The value of LO threshold for each record
Programming the database of thresholds
- 49 -
Fig. 37. Checkweighing – submenu content
− Move the cursor to a field “Database of thresholds (limits)” and press RIGHT
ARROW KEY
− Select number of a record by moving the cursor next to a desired field and press
RIGHT ARROW KEY
Fig. 38. Checkweighing – programming database of thresholds (limits)
− Move the cursor to a field “Database of thresholds (limits)” and press RIGHT
ARROW KEY
Fig. 39. Checkweighing – programming database of thresholds – inserting
thresholds values
− Enter a name for a selected record (name of a product to be weighed)
- 50 -
− Enter the value of HI threshold (limit)
− Enter the value of LO threshold (limit)
− Accept entered values by double pressing of ENTER key
Fig. 40. Checkweighing – mode operation with enabled checkweighing
limits
− Move the cursor to a field “START” and press RIGHT ARROW KEY
− The balance is ready to weigh a product with set checkweighing thresholds (limits)
Fig. 41. Checkweighing – display content
1 – measurement result
2 – pictogram of stable measurement result
3 – working mode name
4 – the value of HI threshold (limit)
5 – the value of LO threshold (limit)
6 – a pictogram indicating the weighing range of currently weighed sample
(LO – OK – HI)
7 – name of a product saved in the database of thresholds
8 – difference between the measurement result and the center of set tolerance field
9 – a pictogram indicating the current “position” of weighed sample in relation to set
checkweighing thresholds (limits)
10 – a bargraph indicating the range of applied measuring range of a balance.
- 51 -
Selecting other product from the database of thresholds (limits)
− While in checkweighing mode press SETUP key
− A message box is opened on the display. Go to the database of thresholds (limits)
and select another record from the database or set other HI and LO thresholds
values if the database is disabled.
18.3. Filling
Filling (dosing) mode is intended for precise measuring or adding a product until reaching a
pre-defined target value. Before the beginning of a measuring cycle the user should set a
target mass, which is simultaneous the HI dosing threshold.
Mode activating
Fig. 42. Filling – mode activating
- 52 -
Display content
Fig. 43. Filling – display content
1 – mass to be placed on the weighing pan to reach a pre-defined target value
2 – bargraph
3 – working mode name
4 – TR (target) the value of target mass which is declared in mode parameters
(see Fig. 42 M3 01 Target mass)
5 – WGH mass currently placed on balance’s weighing pan
18.4. Percent setup
The purpose of this working mode is comparing mass of a weighed load with reference
mass which is specified in mode settings. The result of the comparison process is
displayed in percent.
The reference mass can be set in the options of the working mode or determined by
weighing (see procedure description at the end of point. 18.4. of this user manual).
Working mode Percent Setup can cooperate with additional working modes:
checkweighing, filling and statistics.
Mode activating
Fig. 44. Percent setup – mode activating
- 53 -
Display content
Fig. 45. Percent setup – display content
1 – percent value, i.e. relation between mass of a load placed on balance’s weighing
pan and reference mass saved in parameter settings
2 – working mode name
3 – REF – reference mass (see Fig. 44 – M4 01)
4 – WGH mass currently placed on balance’s weighing pan
Percent setup in cooperation with other working modes
While activating the working mode go to its settings and set parameters: M4 03, 04, 05 to
YES. Then move the cursor next to START field and start working mode operation.
Caution:
On enabling the Checkweighing mode in working mode settings remember to set
the HI and LO checkweighing thresholds (limits) as values expressed in %.
On enabling the Filling mode in working mode settings remember to set the
target value expressed in %.
On enabling Statistics mode in working mode settings remember to move the
cursor to a field: Erase to erase previous statistics, and then move the cursor to
a field Statistics and change its attribute from NO to YES. Accept the settings by
pressing Enter key
- 54 -
Fig. 46. Percent setup – cooperation with other working modes
1 – percent value, i.e. relation between mass of a load placed on balance’s weighing
pan and reference mass saved in parameter settings
2 – pictogram of stable measurement result
3 – working mode name
4 – REF reference mass
5 – WGH mass currently placed on balance’s weighing pan
6 – a pictogram indicating the weighing range of currently weighed sample
(LO – OK – HI)
7 – statistics mode enabled (N=0 – equals to no measurement records in current
statistics)
8 – dosing mode enabled (load mass between 90 – 110%)
On completing a measurement series, e.g. 10 measurements (no, of measurement
N=10) the user can preview the result of carried out statistics from the measurement
series.
−
Enter working mode submenu
−
Set the cursor next to a parameter 05 Statistics
−
Press F key to enter the parameter 05 Statistics
−
Set the cursor next to a parameter 02 Results
−
Enter the parameter to preview results from completed statistics
−
Press ENTER key to print statistics result on a connected printer/computer
−
Return to working mode submenu and higher menu levels by pressing ESC
key.
- 55 -
Fig. 47. Percent setup – cooperation with other working modes –
Statistics
Determining reference mass by weighing a standard
The percent setup mode enables determining reference mass by weighing an accepted
standard.
In such case, when in the main mode window press F key. The software initiates the
procedure by displaying a command. Follow this and other commands visible on the
display.
On completing the procedure the software automatically returns to displaying the main
window of the percent setup mode.
- 56 -
18.5. Animal weighing
The working mode applies a selection of filters which are designed to correctly determine
mass of an object (animal) moving on balance’s weighing pan.
Mode activating
Fig. 48. Animal weighing – display content
Internal mode settings:
-
FILTER (determines the speed (weighing time) required for stabilization of the
final measurement result, the faster the filter setting, the shorter the measurement
time.
-
THRESHOLD (its value is expressed in balance reading units, it is the value
below which the weighing results must come down to automatically enable the
following measurement of weighed object)
-
AUTO START (the function used for automatic startup of the following
measurement processes)
-
STATISTICS (calculation of statistics for each weighed object)
-
RUN (Start measuring process)
- 57 -
18.6. Density determination of solids and liquids
Additional equipment of a balance PS/X series includes a kit dedicated for determining
density of solids and liquids.
Fig. 49. Components of a density kit for balances with a weighing pan 128x128 mm.
1
2
3
4
Stand (weighing pan with a
hanger)
Bottom weighing pan for
determining density of solids
Flexible connection of the
bottom pan
Top weighing pan for
determining density of solids
7
Thermometer
8
Thermometer handle
9
Sinker
10
Beaker basis
5
Beaker
11
6
Hook
12
- 58 -
Additional stand for a set of pans
or a sinker
Additional set of pans for
determining density of solids,
which density is lower than density
of water
18.6.1.
Density determining of liquids
The basic component needed for determining density of liquids is a glass sinker with
precisely determined volume, which value is indicated on sinker’s hook.
Before carrying out density determining process enter the sinker’s volume value to
balance’s memory.
The density determining process is based on comparing mass of the sinker, first by
weighing it in the air, and second by immersing it in the tested liquid.
The result of liquid density is automatically calculated by the balance software, and
indicated on its display.
The measurement result can be sent for multiple times to a connected printer or computer
via RS 232 interface and on pressing PRINT key.
18.6.2.
Density determining of solids
Density of solids can be determined in one of three types of liquids:
−
−
−
WATER (distilled water),
ALCOHOL (spirit 100% +/- 0.1% in reference temperature: 20 °C),
OTHER (another liquid with known density)
The density determining process is based on comparing mass of a sample, which is first
weighed it in the air (i.e. placed on the top weighing pan) and mass of the same sample
which is immersed in the liquid (i.e. placed on the bottom weighing pan of the density kit).
Based on obtained measurement results, the software calculates the density of tested
sample and indicates on the balance’s display. The measurement result can be sent for
multiple times to a connected printer or computer via RS 232 interface and on pressing
PRINT key
Detailed description of the density determining process is described in the user
manual attached to the kit for determining density of solids and liquids.
- 59 -
18.7. Formulation
Formulation mode is intended for preparing mixtures in accordance with pre-defined
formulas. It is highly recommended for pharmacies. The software of balance PS/X series
features calculation memory, therefore it stores mass of each ingredient of a mixture and
sums of weighed ingredients.
While using formulation mode the balance’s display shows and continuously updates the
following data:
1. Mass of a load placed on balance’s weighing pan
2. Name of currently weighed ingredient (max 10 characters)
3. “WGH” Mass to be added while weighing a specific ingredient
4. “IC” Number of ingredients which are already weighed in a prepared mixture
5. “SUM” Sum of ingredients mass which are already weighed in a prepared mixture
Mode activating
Fig. 50. Formulation – internal mode settings
parameter 01 Prompts (Hints)
on enabling, the balance’s graphic display indicates name and mass of each weighed
ingredient in a formulation, i.e. data specified in parameter 04 Formulation
parameter 02 Automatic printout
on enabling the parameter, and on confirmation the software automatically sends mass of
each weighed ingredient via RS 232 interface to a connected printer or computer
- 60 -
parameter 03 No. of ingredients
here the user can set number of ingredients in a prepared mixture (maximum no. of
ingredients: 20)
parameter 04 Formulation
entering this parameter settings opens another submenu for specifying names (max 10
characters) and settings (target mass) for each ingredient in a prepared mixture.
parameter 05 Formulation printout
enabling this function causes printing parameters of an active formulation on a connected
printer. The printout contains names and settings of each ingredient in a formulation and
total sum of a complete formulation.
parameter 06 Statistics
enabling (YES) or disabling (NO) of statistical calculations.
CAUTION:
The statistical calculations refer only to the total mass of prepared mixture (mass of each
ingredient in a formulation is not included in the statistics).
parameter 07 Start
startup of Formula making mode
Display content in formula making mode
Fig. 51. Formulation – display content
1 – previewing mass currently placed on balance’s weighing pan.
2 – pictogram of stable measurement result
3 – working mode name
4 – target mass of the currently weighed ingredient, as specified in the parameter
04 Formulation
5 – Sum of all weighed ingredients of a formulation which are saved in balance’s
calculating memory
6 – Number of already weighed ingredients in a prepared formulation
7 – name of currently weighed ingredient
8 – bargraphs on the left side of the display, which denote the mass to be added
(dosed) to reach pre-defined mass of each weighed ingredient. While reaching
the target mass the descriptions on accuracy visible on the bargraph are
changing.
- 61 -
Fig. 52. Bargraphs – automatic scaling
Means of preparing mixtures – in accordance with data set in working mode settings
on ingredients and their mass
Go to parameter 04 Formulation and enter names and mass of the ingredients in a
formulation. Remember the following conditions:
− Each name can comprise maximum 10 characters,
− Each name has to be accepted by pressing ENTER key, and next set ingredient’s
mass to be weighed in a formula making process
Fig. 53. Declaring a formulation
−
−
−
−
−
Total mass of a prepared formulation and mass of the vessel in which the
formulation is prepared must not exceed maximum measuring range (max.
capacity) of a balance
A formulation can contain maximum 20 ingredients
Parameter 03 No. of ingredients enables specifying number of the ingredients in a
prepared formulation
Remember that maximum number of ingredients in a formulation is 20
While preparing a formulation the software orders dosing the ingredients in
accordance with the their sequence as set in parameter 04 Formulation; e.g. if a
- 62 -
−
−
•
•
•
•
•
•
•
•
user sets 10 ingredients in parameter 04 Formulation, and then sets no. of
ingredients in a formulation to 8, then the software will complete formula making
process after weighing the first 8 ingredients.
The software prepares a list of ingredients in accordance with the sequence set in
parameter 04 Formulation, and always starts the formula making process from the
first ingredient on the list, and ends the process on an ingredient number as set in
parameter 03 No. of ingredients.
If a user needs a documentation from a formula making process, e.g. in a form of
a printout, then set parameter 02 Automatic printout to 1 : YES. In such case
each accepted mass of an ingredient (by pressing UNITS key) is automatically
printed on a connected printer or computer.
Set parameter 01 Prompts (Hints) to 1 : YES.
Enter Formulation mode by pressing ENTER key.
Tare mass of a vessel for formula making process.
Weigh the first ingredient of a formulation (ingredient’s mass is visible in the WGH
field)
Press UNITS key. Mass of the first ingredient is saved in balance memory. The
parameters visible on the display will change to:
ingredient 2, mass WGH, IC=1, SUM=. . . .
Mass indication on the display will zero.
Repeat the process for all the ingredients set in a formulation
After weighing the last ingredient of a prepared formulation and saving its mass in
balance memory (by pressing UNITS key) the display automatically changes to
the total mass of prepared formulation. The mass value is also locked on the
display, and there are prompts on possible activities.
Means of preparing mixtures without entering data to balance memory on
formulation ingredients and their mass
If a user needs a documentation from a formula making process, e.g. in a form of a
printout, then set parameter 02 Automatic printout to 1 : YES.
In such case each accepted mass of an ingredient (by pressing UNITS key) is
automatically printed on a connected printer or computer.
•
•
•
•
•
•
•
•
•
Set parameter 01 Prompts (Hints) to 0 : NO.
Enter Formulation mode by pressing ENTER key
Tare mass of a vessel for formula making process
Pour an ingredient no. 1 to the vessel until reaching desired target value (follow
criteria on prepared formulation).
Press UNITS key. Mass of the first ingredient is saved in balance memory. The
parameters visible on the display will change to: IC=1, SUM=. . .
Mass indication on the display will zero.Press UNITS key.
Repeat the process for all the ingredients set in a formulation
After weighing the last ingredient of a prepared formulation press →0/T← key.
The formula making process is completed. The indication with total sum of
prepared formulation is locked on the display.
Press PRINT key to print (send) a report from a completed formulation to a
connected printer of computer.
- 63 -
Statistical calculations
Statistical calculations are carried out only on total mass of prepared formulation (mass of
each ingredient in a formulation is not included in the statistics). If a user wants to run
statistics if the formula making mode, then:
1. Go to parameter 06 Statistics
2. Erase results of previous statistical calculations
3. Set parameter 06 Statistics to YES
4. Enter the formula making mode
5. Carry out required series of measurements
6. Once again go to parameter 06 Statistics
7. Enter parameter 06 02 Results
8. In order to print statistics press PRINT key.
18.8. Statistics
Mode activating
Fig. 54. Statistics – mode activating
The very first process after entering the Statistics mode should be erasing the results of
previous statistical calculations. It is carried out by using option M8 01 Erase.
All statistical data are updated on an ongoing basis after saving a measurement result in
balance memory. Adding another measurement to a series is carried out on placing a
weighed load on balance weighing pan, stabilization of measurement result (the measuring
unit appears on the display) and pressing ENTER key.
The user determines whether statistical data should be visible on the graphic of a balance
display while carrying out the measuring process. This parameter is set in statistics mode
submenu (the data is visible on setting the parameter to “YES”).
- 64 -
Independently on the settings (YES / NO) on the printout of final result of statistical
calculations (enabled by pressing F key) comprises the following data.
N
:
SUM :
X
:
MIN :
MAX :
D
:
SDV :
RDV :
5
161.121 g
32.224 g
20.486 g
35.578 g
15.092 g
6.581 g
20.4 %
(number of measurements)
(total mass of all statistical records in a measured series)
(average mass of all statistical records in a measured series)
(minimum mass)
(maximum mass)
(difference Max- Min)
(standard deviation)
(variance factor)
Fig. 55. Statistics – display content including a series of measurements
1.
2.
3.
4.
5.
6.
7.
Mass currently placed on the weighing pan
Number of measurement in a measuring series
Sum of all completed measurements in a series
Average mass of all completed measurements in a series
Minimum saved mass in a carried out measuring series
Maximum saved mass in a carried out measuring series
The difference between the minimum and maximum saved mass in a measuring
series
8. Precisely calculated standard deviation value
9. Variance factor value
10. Measuring unit [g]
11. Working mode name
Statistics mode features a special option enabling quick calculating of statistics from a
measuring series with a possibility of generating reports from the completed calculations.
The user can declare the content of a header and footer in a printout of statistical report.
The header <PRINTOUT 1>, and the footer <PRINTOUT 2> are settable in non-standard
printouts.
In order to correctly use the option, the user has to create templates 1 and 2 using the nonstandard printouts (see point 19.2). As the templates are ready, the option can be enabled
in mode settings.
- 65 -
Means of operation:
−
−
Press
key to print the header (PRINTOUT 1)
Carry out a measuring series (set all options of the GLP menu to NO), and accept
each measurement result by pressing <ENTER> key
On completing a measuring series press F key to print a statistics from the series
In order to continue the measuring series accept it by pressing <ENTER> key or
−
Press
−
−
key to print a footer (PRINTOUT 2).
For the purpose of increasing the speed of statistical calculations it is possible to enable
the option of automatic erasing statistics. The option is set in parameter: P5 (RS 232) 12
<Erase statistics>.
0 - no (the statistics are not erased. Erasing is carried out by entering mode settings and
selecting option <ERASE>
1 – on header (the statistics is erased directly on pressing
printout of a header)
2 – on footer (the statistics is erased directly on pressing
- 66 -
key which precedes
key after printing a footer).
19. PRINTOUTS
19.1. Standard printout
A balance PS/X series features 2 basic types of printouts. The first one is a standard
printout which comprises of a measurement result and all variables set in the GLP
submenu which attribute is set to YES. In case of fields User and Project the user can
enter alphanumeric data.
Fig. 56. Declaring variables for a standard printout – submenu GLP
An example of a standard printout:
Fig. 57 An example of a standard printout
(all options in the GLP menu are set to YES, i.e. present on a printed)
- 67 -
Rys. 58 Przykład wydruku standardowego
A question mark (?) preceding the mass of a measured load on a printout indicates that the
result was unstable.
19.2. Non-standard printouts
Principles of creating non-standard printout templates:
− balance enables creating up to 4 custom printout templates,
− each template must have the string of text start and end specified, e.g. Printout
no. 1 Start – 1 and Printout no. 1 Stop – 40. In this case the Printout no. 1
contains text strings from 1 to 40.
− Next insert the texts into the specified text strings, i.e. 1 ÷ 40.
it is recommended to use an external computer keyboard connected to balance’s
port. This means of text input is much simpler and quicker.
− Non-standard printout templates may overlap each other, i.e.:
Printout 1 Start – 1
Printout 1 Stop – 40
Printout 2 Start – 20
Printout 2 Stop – 40
Non-standard printout templates are easily created using printout editing option.
Caution: while text input it is necessary to add all required special signs, such as CRLF,
tabulator, etc. When using printout editing option, all of the special signs are selectable
from available menu. they are grouped on the one side of text editing option, and
included in a printout by adding them to the field Printout.
Fig. 59. Menu Printouts – mode activating
- 68 -
A non-standard printout can contain:
− Variables dependent on an enabled working mode and other user needs (mass,
date, project no.)
− Texts inserted in balance’s user menu
− A custom non-standard printout can contain up to 640 characters inserted in 80
text strings, 8 character each. (starting with parameter String 1 to String 80). A
balance user can create up to 4 non-standard printout template).
19.2.1.
Inserting text into strings
Variables available in all working modes and having the same value
%%
Printout of a single character “%”
%N
Current net mass in basic measuring unit
%d
Current date
%t
Current time
%i
Balance factory no.
%R
Software no.
%P
Project no.
%U
User no.
%F
Name of an active working mode
%C
Date and time of last completed adjustment process
%K
Type of last completed adjustment process
%I
Deviation in last completed adjustment process
%1
Code 1
%2
Code 2
%3
Code 3
%4
Code 4
%5
Code 5
%6
Code 6
Variables dependent on a currently enabled working mode
Working mode in which the variable is
Variable Description
active
%W
Mass of a single part PARTS COUNTING
%H
HI high threshold
%L
LO Low threshold
%Z
Target mass
CHECKWEIGHING
DOSING
- 69 -
%B
Reference mass
%A
Filter
%b
Threshold (limit)
%i
Liquid
%p
Procedure
%c
Temperature
%a
Liquid density
%v
Sinker volume
PERCENT SETUP
ANIMAL WEIGHING
DENSITY DETERMINATION
Static variables available in all working modes except for weighing (basic mode)
%n
Measurement no.
%x
Average value
%S
Sum
%m
Minimum value
%M
Maximum value
%D
Difference between max and min value
%s
Standard deviation
%r
Variance factor
Variable available in all working modes and accepting a value related to an enabled
working mode
%V – Mass in current measuring unit. Variable value is combined with an active
working mode, e.g. number of counted parts in Parts Counting mode or
deviation from reference mass in % in the Percent Setup mode
Special signs for designing a non-standard printout template
\\
Single “\” sign
\c
CRLF
\r
CR
\n
LF
\t
Tabulator
\s
Skip to the following text ”string”
\0
End of a printout template
Each text string (Text 1 ÷ 89 Text 80) can contain up to 8 characters (letters, digits, special
signs, space). Inputting a sentence comprising multiple words and signs requires using a
set of neighbouring 8-character text strings. A user can add special signs to include
needed variables in a non-standard printout template.
- 70 -
Example no 1:
Maximum mass cannot exceed 11.250 g!
Inputting this sentence requires using 36 characters grouped in the neighbouring text
strings. Enter text strings settings and input 8 characters from the above text into each of
the text strings until completing the sentence.
Text string no
19
20
21
22
23
Text 10
Text 11
Text 12
Text 13
Text 14
Text
1
M
m
n
e
0
2
a
a
o
d
3
x
s
t
g
4
i
s
1
!
5
m
e
1
6
u
c
x
.
7
m
a
c
2
8
n
e
5
Example no. 2:
“RADWAG” Balances & Scales
Date:
Hour:
Load mass
*****Signature:.........
***<active working mode >***
Enter text strings settings and input 8 characters from the above text into each of the text
strings until completing the printout.
Text string no
25
26
27
28
29
30
31
32
33
34
35
36
37
Text 16
Text 17
Text 18
Text 19
Text 20
Text 21
Text 22
Text 23
Text 24
Text 25
Text 26
Text 27
Text 28
Text
1
2
“
R
B
s
e
s
e
:
r
:
L
o
s
:
*
*
n
a
.
.
.
\
*
*
- 71 -
3
A
a
&
d
%
a
%
*
t
.
c
*
4
D
l
\
\
t
d
N
*
u
.
*
5
W
a
S
c
c
\
\
*
r
.
*
6
A
n
c
D
H
r
m
c
S
e
.
*
7
G
c
a
a
o
\
a
\
i
:
.
%
8
“
e
l
t
U
n
s
c
g
.
.
F
Principles of inserting texts
− Using keys on balance’s overlay
Toggling upwards through all available characters: digits, letters, and signs by
one value.
Toggling downwards through all available characters: digits, letters, and signs
by one value.
Selecting a character for modification by moving the cursor to the RIGHT (the
following pressing of the the right arrow key causes activating a character for
modification (character is flickering; if no character is inserted, then repeated
pressing of this key causes adding a space in the text)
Selecting a character for modification by moving the cursor to the LEFT
(another pressing of the left arrow key causes a erasing a flickering character,
and causes flieckering of a character located on the left from the erased one.)
Accept an inserted character
−
Using computer keyboard PS/2 type
Press F2 key to enter main menu of a balance. Press F3 or use navigating arrows
to place the cursor next to a group of parameters P6 Printouts and by pressing F2
key enter the submenu group. Then, using the navigating arrows place the cursor
next to a desired parameter and press F2 key to activate text inserting procedure.
Use keyboard text keys to insert a text into the strings (max 8 characters per one
text string) and accept it by pressing Enter key. Repeat the process for the other
text strings.
19.2.2. Designing texts using Printout Editing mode
Mode activating
Fig. 60. Non-standard printouts – printout editing
- 72 -
Rys. 60-1. Non-standard printouts – printout editing
On enabling the printout editing mode select a number of a non-standard printout (1-4) and
the place for the beginning of text in a printout (text strings from 1 to 80). Then, go to Edit
option to design a printout template. On pressing RIGHT ARROW KEY, the software
enters printout editing mode.
Fig. 61. Printout editing – selecting printout components
Use navigating arrow keys (up and down) to move the cursor between the following
fields. Press RIGHT ARROW KEY to add a selected component to a printout template.
On completing editing of a printout template press ENTER/PRINT key. The display shows
a message asking whether to create a printout template – once again press ENTER/PRINT
key to confirm.
19.2.3.
Activating non-standard printouts
If an active printout template is set to STANDARD, then a printout comprises data on
measured mass and variables declared in the GLP menu (see point 18.1 Standard
printout – Fig. 60. Declaring variables for a printout – submenu GLP).
If a user wants to enable a non-standard printout template (1 to 4), then they need to select
a non-standard printout template and specify its beginning and end (the text strings of
printout start and stop).
- 73 -
20. COOPERATION WITH A PRINTER OR A COMPUTER
Each pressing of < PRINT > key causes sending to a connected printer or computer a
signal corresponding to current mass indication (display status) with enabled measuring
unit. The default baud rate setting of a balance is 9600 bit/sec. If a peripheral device (a
printer or a computer) requires other baud rate settings then it needs to be changed in
balance parameter settings.
20.1. Cross-section through connecting cables
Fig. 62. Connecting cables balance-computer
- 74 -
a balance: slot DB 9/F – a computer slot DB 9/F (with control of data transmission)
Balance
2 (RxD)
3 (TxD)
4 (DTR)
5 (GND)
6 (DSR)
7 (RTS)
8 (CTS)
Computer
3 (TxD)
2 (RxD)
6 DSR
5 (GND)
6 (DTR)
8 (CTS)
7 (RTS)
21. COOPERATION WITH A CITIZEN LABEL PRINTER
Ensuring correct balance cooperation with a label printer requires acting as specified in the
following description. Use computer software “ETISOFT LABELS” to design a label
template according to user needs:
− Design size of a label
− Design number and type of data to be included in a label
CAUTION:
In order to correctly print variables from a balance on a label printer, the variables should
have a required space (number of characters) designed on a label. Number of characters
needed for each variable is specified in a below tables: 2, 3 and table 4.
Save a label template on a computer disc and name it using alphanumeric characters.
Assign designed label template to memory of a printer CITIZEN CLP-521:
−
−
Set baud rate for RS 232 interface of a label printer to 9600b/s
An instance of a designed label template named “Label01”
Fig. 63. A label template
Design a non-standard printout in a balance which enables printing a label (i.e. following
the data included in the designed label template). Set required printout parameters, e.g.:
− Printout no.
− Text string for start and stop of a selected printout
- 75 -
−
After each measurement result the printer should print 3 labels
Principles for designing a printout:
− Insert into text strings data to be included in a printout – group of parameters P6
Printouts; parameters: Text 01 ÷ Text 80.
When designing a printout template use variables for controlling label printout (table 1)
and variables for sending specific data from a balance.
TABLE 1
\02L\c
rlabel name\c
Give name of alabel
X\c
Srart of variables editing
\02U01NN\c
Variable no. 1; NN – variable symbol
\02U02NN\c
Variable no. 2; NN – variable symbol
\02U03NN\c
Variable no. 3; NN – variable symbol
\02UnnNN\c
Variable no. nn. NN – variable symbol
Paper offset by nnn value in [mm] – depending on label
size
End of variables of editing
\02fnnn\c
E\c
−
Beginning of a label
\02Ennnn\c
Print nnnn quantity of labels
\02G\c
End of a label
An instance of a printout template for a label (following parameters from table no.
1)
Fig. 64. Label template saved in a factory menu
−
On adding data on a non-standard printout set other printout parameters, such
as:
Printout no.
–1
Printout no. 1 start – 1
Printout no. 1 stop – 10
- 76 -
Fig. 65. Declaring printout content
−
On setting printout parameters go back to the weighing mode with procedure of
saving carried out changes.
Next, connect a label printer to balance’s communication interface using a dedicated
cable (see figure on cross-section of a connecting cable given in this user manual).
Check transmission parameters of a balance and printer – they should be equal.
Place a weighed load on balance’s weighing pan and on stabilization of measurement
result press PRINT key on balance’s overlay. The balance sends data to a connected
printer complying with saved template, and the printer prints 3 labels as designed in
the software.
Presentation of a label:
Fig. 66. A presentation of a printed label
- 77 -
TABLE 2
Variables independent on enabled working mode
Number of characters
needed for a variable
Variable description
%%
1
Printout of a single character “%”
%N
16 or 18 *
Current net mass in basic measuring unit
%d
10
Current date
%t
8 (for 24-hour version)
Current time
%i
8
Balance factory no.
%R
8
Software no.
%P
8
Project no.
%U
8
User no.
%F
X **
Name of an active working mode
%C
25
Date and time of last completed adjustment
process
%K
X **
Type of last completed adjustment process
%I
16 or 18 *
Deviation in last completed adjustment
process
%1
6
Code 1
%2
6
Code 2
%3
6
Code 3
%4
6
Code 4
%5
6
Code 5
%6
6
Code 6
16 or 18 *
Mass in current measuring unit. Variable
value is combined with an active working
mode, e.g. number of counted parts in
Parts Counting mode or deviation from
reference mass in % in the Percent Setup
mode
Variable
%V
* depending on settings of a digit marker and printout parameter: to a printer / PC
** depending on the length of a name
- 78 -
TABLE 3
Variables dependent on a currently enabled working mode
Number of
Working mode in which the
Description
Variable
characters
variable is active
%W
16 or 18 *
Mass of a single part
PARTS COUNTING
%H
16 or 18 *
HI high threshold
%L
16 or 18 *
LO Low threshold
%Z
16 or 18 *
Target mass
DOSING
%B
16 or 18 *
Reference mass
PERCENT SETUP
%A
14
Filter
%b
14
Threshold (limit)
%i
14
Liquid
%p
14
Procedure
%c
14
Temperature
%a
16
Liquid density
%v
16
Sinker volume
CHECKWEIGHING
ANIMAL WEIGHING
DENSITY DETERMINATION
TABLE 4
Static variables available in all working modes except for weighing (basic mode)
%x
Number of
Description
characters
7
Measurement no.
16
Average value
%S
16
Sum
%m
16
Minimum value
%M
16
Maximum value
%D
16
Difference between max and min value
%s
16
Standard deviation
%r
16
Variance factor
Variable
%n
* depending on settings of a digit marker and printout parameter: to a printer / PC
** depending on the length of a name
- 79 -
22. COOPERATION WITH EPSON RECEIPT PRINTER
For the purpose of using Polish letters in the printouts it is necessary to:
− On the beginning of a printout that is programmed in a balance add a formula on
coding page change to CP 852
Recording scheme:
\1B\74\12\c
−
Design a label template using according to user needs and bearing in mind the
following relations for use of Polish letters:
CP 852
CP 852
ą
ć
ę
ł
ń
ó
ś
ź
ż
\A5
\86
\A9
\88
\E4
\A2
\98
\AB
\BE
Ą
Ć
Ę
Ł
Ń
Ó
Ś
Ź
Ż
\A4
\8F
\A8
\9D
\E3
\E0
\97
\8D
\BD
(instead of using Polish letters insert their code equivalents)
If after completing a printout the paper should be cut, then at the end of a designed printout
template add a text:
\1D\56\41\08\C
Cross-section through connecting cable
balance– Citizen printer , balance – Epson printer
Fig. 67. Cross-section through connecting cable: balance – Epson / Citizen printer
- 80 -
23. UNDER HOOK WEIGHING
A balance PS/X series comes standard with a possibility for weighing loads under the
weighing pan. Follow below description for enabling under hook weighing process:
1.
2.
3.
4.
5.
Remove plastic hole plug located in the bottom of balance’s base,
There is suspension place for hook visible in the hole – the suspension is installed
permanently to balance mechanism,
In the hole install the hook for under hook weighing - the hook does not come
standard with a balance),
Tare mass of the hook to balance’s memory
Weigh loads using under hook option.
CAUTION:
1. The suspension for hook must not be turned, twisted or manipulated in any
direction. Such actions may cause damage to balance mechanism.
2. Mass of all additional elements of the under hook weighing kit, like: a hook, a
weighing pan, a string, etc. should be zeroed by pressing TARE key.
24. CONNECTING EXTERNAL BUTTONS
A balance PS/X series enables connecting external buttons for tarring or printing
measurement results without the need to touch balance’s keyboard with operator’s hands.
The buttons are connected using a dedicated splitter connected to balance’s RS 232
interface.
Additionally the splitter enables connecting a printer or a computer.
The splitter and buttons are additional equipment (optional) of a balance PS/X series.
25. LIST OF COMMANDS COMPUTER - BALANCE
Function
Command
INTERFACE RESET
R CR LF (zeroing currently carried out commands, restoring factory default
settings)
Function
Command
SEND ALL IMPLEMENTED COMMANDS
PC CR LF (sends information on all commands implemented in the
balance’s software)
Function
Command
SEND MEASUREMENT RESULT IN BASIC MEASURING UNIT
S CR LF (sends result in basic measuring unit on stabilization of indication)
Function
IMMEDIATELY SEND MEASUREMENT RESULT IN BASIC MEASURING
UNIT
SI CR LF
Command
- 81 -
Function
Command
SEND MEASUREMENT RESULT IN CURRENT MEASURING UNIT
SU CR LF sends result in current measuring unit on stabilization of
indication)
Function
Command
IMMEDIATELY SEND MEASUREMENT RESULT IN CURRENT
MEASURING UNIT
SUI CR LF
Function
Command
ZERO BALANCE
Z CR LF (zeroing of indication on stabilization)
Function
Command
IMMEDIATELY ZERO BALANCE
ZI CR LF
Function
Command
TARE WHEN STABLE
T CR LF
Function
Command
IMMEDIATELY TARE BALANCE
TI CR LF
Function
SWITCH OFF CONTINUOUS TRANSMISSION IN BASIC MEASURING
UNIT
C0 CR LF
Command
Function
Command
Function
Command
Function
SWITCH ON CONTINUOUS TRANSMISSION IN BASIC MEASURING
UNIT
C1 CR LF
SWITCH OFF CONTINUOUS TRANSMISSION IN CURRENT
MEASURING UNIT
CU0 CR LF
Command
SWITCH ON CONTINUOUS TRANSMISSION IN CURRENT MEASURING
UNIT
CU1 CR LF
Function
Command
GIVE FACTORY NUMBER
NB CR LF
Function
Command
GIVE MEASURING RANGE
FS CR LF
Function
Command
GIVE SOFTWARE REVISION
RV CR LF
Function
Command
GIVE OR CHANGE DATE IN A BALANCE
PD CR LF (causes sending data on set date or changes the date)
Function
Command
GIVE OR CHANGE TIME IN A BALANCE
PD CR LF (causes sending data on set time or changes the time)
- 82 -
Function
Command
GIVE ENABLED WORKING MODE
PM CR LF
Function
Command
SEND SETUP
PS CR LF (causes sending complete data on balance setup – printout of
parameters)
Function
Command
“BEEP” SOUND
B CR LF (causes immediate activating of beep sound in a balance)
Function
Command
GIVE LAST CODE ERROR
ER CR LF (causes sending code of last saved error in a balance)
Function
Command
SEND TEXT STRING
DS CR LF (causes previewing a sequence of characters)
Function
Command
ERASE TEXT STRING
CS CR LF (causes erasing a text string and restoring default display status)
Function
Command
SHOW HEADER
DH CR LF (causes previewing a sequence of characters in the upper bar of
the display)
Function
Command
ERASE HEADER
CH CR LF (causes erasing a text string from the upper bar of the display)
Function
Command
SHOW FOOTER
DF CR LF (causes previewing a sequence of characters in the bottom bar
of the display)
Function
Command
ERASE FOOTER
CF CR LF (causes erasing a text string from the bottom bar of the display)
Function
Command
CARRY OUT INTERNAL ADJUSTMENT PROCESS
CL CR LF
Function
Command
LOCK KEYBOARD
KL CR LF
Function
Command
UNLOCK KEYBOARD
KU CR LF
Function
Command
SWITCH OFF KEYBOARD “ECHO“
E0 CR LF (disables sending codes of pressed keys and buttons)
Function
Command
SWITCH ON KEYBOARD ”ECHO“
E1 CR LF
Function
Command
SWITCH OFF THE BALANCE
O0 CR LF (equal to pressing ON/OFF button)
- 83 -
Function
Command
SWITCH ON THE BALANCE
O1 CR LF (equal to pressing ON/OFF button)
Function
Command
DISABLE ZUTOZERO
A0 CR LF
Function
Command
ENABLE AUTOZERO
A1 CR LF
If a non-existing or incorrect command finished with CR LF is sent to a balance, it
responses with E S CR LF. Spaces between characters should be omitted, as they are
added only for the purpose of proper legibility.
26. ERROR MESSAGES
Message
"Control sum error."
" A/D converter error"
"Measuring range
exceeded"
"Measuring range
exceeded"
"A/D Null"
Error
code
1.1
1.2
2.1
2.2
2.3
"A/D Full"
2.4
"Tare/Zero out of range"
2.5
"Tare out of range"
2.6
"Zero out of range”
2.7
"Result > 4% Max"
2.8
"Result > 1% Max"
2.9
"Part < 1 Div"
2.10
“Part < 10 Div"
2.11
"Ref < 1000 Div"
2.12
"Out of range"
"Incorrect value "
3.1
3.2
"DRH - locked"
3.3
Error description
Error related to data transmission
Converter error
Maximum capacity (measuring range) of the
balance exceeded (over load)
Maximum capacity (measuring range) of the
balance exceeded (over load)
No divisions from the converter
Maximum quantity of divisions from
converter exceeded
Permissible value of zeroing or tarring range
exceeded
Permissible value of tarring range exceeded
Permissible value of zeroing range
exceeded
Too high start mass (balance started with a
load on the weighing pan)
The difference between mass of a currently
measured adjustment weight and mass
saved in balance memory is greater than
(difference >1%)
Mass value of a single part in Parts Counting
mode is smaller than balance reading unit
Load value placed on the weighing pan
while determining mass a single part in Parts
Counting mode is smaller than 10 reading
units of a balance
Value of a reference mass in Percent Setup
mode in smaller than 1000 reading units
Parameter value exceeds permissible value
Impermissible parameter value
Parameter change blocked (DRH function in
the factory menu is enabled)
- 84 -
"Overwriting error "
"Parity error"
"Frame error"
"CTS transmission
suspended "
"XOFF transmission
suspended "
"Incorrect date"
4.1
4.2
4.3
"Time value exceeded"
6.1
4.4
Errors relating to data transmission to a
computer or a printer connected to a
balance
4.5
5.1
Error of date setting
Timeout error for carrying out a given
process (e.g. zeroing).
User manual no.:
LMI-38-06/04/13/ENG
- 85 -
MANUFACTURER
OF ELECTRONIC WEIGHING INSTRUMENTS
RADWAG WAGI ELEKTRONICZNE
26-600 Radom
28 Bracka
POLAND
phone +48 48 38 48 800
fax. + 48 48 385 00 10
e-mail: [email protected]
www.radwag.com
- 86 -