Download Sharp SJ-43N-BE Service manual
Transcript
SJ-P43N/43N SJ-P47N/47N SERVICE MANUAL S6511SE47ATUET REFRIGERATOR-FREEZER MODELS SJ-P43N-SL1/WH1 SJ-43N-SL1/WH1 SJ-P47N-SL1/WH1 SJ-47N-SL1/WH1 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. SJ-P43N,SJ-P47N SJ-43N,SJ-47N DESTINATION .........................E This equipment complies with the requirements of Directives 96/57/EC, 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Refrigerant; HFC-134a Refer to "HFC-134a COOLING UNIT" Service Manual for handling this refrigerant. TABLE OF CONTENTS page ENERGY LABEL ................................................................................................................................................ 2 INSTALLATION ................................................................................................................................................. 2 CAUTIONS AND INFORMATIONS ................................................................................................................... 3 SPECIFICATIONS ............................................................................................................................................. 4 THE FICHE ........................................................................................................................................................ 5 DESIGNATION OF VARIOUS PARTS .............................................................................................................. 6 DIMENSIONS .................................................................................................................................................... 7 LIST OF ELECTRICAL PARTS ......................................................................................................................... 9 WIRING DIAGRAM .......................................................................................................................................... 10 FUNCTIONS .................................................................................................................................................... 14 ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS .............................................................. 18 COOLING UNIT ............................................................................................................................................... 25 REPLACEMENT PARTS LIST ........................................................................................................................ 27 SHARP CORPORATION 1 SJ-P43N/43N SJ-P47N/47N ENERGY LABEL Usage of "the ENERGY LABEL" When displaying this refrigerator in the shop-window, attach the "ENERGY LABEL" to it in the following procedure. Fix the data part of "ENERGY LABEL (DATA)" on the data part of "ENERGY LABEL (BASE)" E A B C D E F G "ENERGY LABEL (DATA)" (This label is in Operation manual) Data part "ENERGY LABEL (BASE)" of each language Refrigerator INSTALLATION Free standing type To ensure adequate ventilation for this refrigerator, install with 6 cm space at the rear and both sides, with a minimum space of 9 cm above the refrigerator. 9cm 6cm 6cm This refrigerator shall be used under the ordinary place condition between +5˚C and +38˚C of ambient temperature, and also not be left under -10˚C for long days. To be used this refrigerator within the range of the rated voltage+6% 2 SJ-P43N/43N SJ-P47N/47N CAUTIONS AND INFORMATIONS In case of following troubles, the cause is not related with the failure of refrigerator. Please mention the correct way to the customer for the use of refrigerator when the repairing. 1. Some foods froze in the refrigerator compartment. Do not place food directly in front of cold air outlet. This may lead to the food freezing. cold air flow IN OUT 2. Some plastic parts were cracked or split. Some household cleaning chemicals may affect the internal food liner and plastic parts resulting in splitting or cracks occurring. When cleaning all plastic parts inside this refrigerator, only use diluted dishwashing liquid(soapy water). Make sure that all plastic parts are thoroughly rinsed with water after cleaning. 3. IT IS NORMAL for the refrigerator to produce the following sounds. Cracking or crunching sound; Sound produced by expansion and contraction of inner walls and internal parts during cooling. Squeaking sound; Sound produced by expansion and contraction of internal parts. Sound of flowing fluid (gurgling sound, fizzing sound); Sound of refrigerant flowing in pipes (sound may become louder from time to time). 3 SJ-P43N/43N SJ-P47N/47N SPECIFICATIONS Items Type Outer dimensions (Including spacer) Height Width Depth Rated storage volume (Rated volume) Gross volume Defrosting System Start Finish Temperature control No-frost freezer Interior lamp Caster Evaporating pan Refrigerator R glass shelf ass'y Compartment V glass shelf ass'y Vegetable case V parting plate R door pocket Egg tray R door pocket S Bottle pocket Bottle stopper Door pocket Fresh case Freezer Freezer tray Compartment Ice cube maker Ice storage box Door pocket Deodorizing unit Plasmacluster RATING Items Rated voltage (V~) Rated frequency (Hz) Climate class Rated current (A) Rated input of heating elements (W) Refrigerant (Charging quantity) [Non-flammable] Insulation blowing gas [Flammable] Net Weight (kg) PLUG TYPE Plug cord Plug type Destination mark COLOR Items Outside color Inside color SJ-P43N SJ-43N 2-Door 1700mm(66.9") 680mm(26.8") 660mm(26.0") 347 liter (12.3cu.ft) F: 99liter (3.5 cu.ft) R: 248 liter(8.8 cu.ft) 370 liter (13.1cu.ft) F: 107liter (3.8 cu.ft) R: 263 liter(9.3 cu.ft) Heater system Automatic Automatic Automatic (Adjustable) Yes 1 2 1 2 1 1 1 1 1 2 1 1 1 1 1 Twin ice cube maker 1 2 2 ( Honeycomb type) Yes No SJ-P47N SJ-47N 2-Door 1820mm(71.7") 680mm(26.8") 660mm(26.0") 384 liter (13.6 cu.ft) F: 99 liter (3.5 cu.ft) R: 285 liter(10.1 cu.ft) 407 liter (14.4 cu.ft) F: 107 liter (3.8 cu.ft) R: 300 liter(10.6 cu.ft) Yes No SJ-P43N SJ-43N 220-240 50 ST 1.2-1.3 128-152 HFC-134a(105g) Cyclo pentane (HC) 70 66 SJ-P47N SJ-47N 72 68 2 pin + Earth CS Receptacle E -SL1 Silver White -WH1 White 4 SJ-P43N/43N SJ-P47N/47N THE FICHE (according to ANNEX NO. 1 2 3 4 5 6 : 94/2/EC) Description Items Trade mark Model name Type Energy efficiency class Eco-award mark Energy consumption (220V 50Hz at 25 C) Remarks SJ-P43N,SJ-43N Category; 7 SJ-P47N,SJ-47N Category; 7 B B 500 kWh/year 550 kWh/year fridge / freezer A++/A+/A~G 880/92 EN153 7 Net storage volume of fresh food storage compartment 248 L 285L 8 Net storage volume of frozen food storage compartment 88 L 88 L 11 L 11 L 4-STAR 4-STAR 2-STAR 2-STAR No frost 9h 6.0 kg /24h ST No frost 9h 6.0 kg /24h ST 39 dB(A) re 1 pw 39 dB(A) re 1 pw 86/594/EEC 746 kWh/year E max 9 10 11 12 13 14 Star rating of frozen food compartment No frost Temperature rise time Freezing capacity Climate class Noise at 25 at 25 (96/57/EC) 15 Maximum allowable electricity consumption (Emax) 709 kWh/year (1.94) 5 (2.04) (kWh/day) SJ-P43N/43N SJ-P47N/47N DESIGNATION OF VARIOUS PARTS The names in parenthesis are the denominations used in the REPLACEMENT PARTS LIST. 17 1 18 2 3 26 19 4 5 6 7 5 8 20 Plasmacluster 21 22 9 23 24 10 11 12 13 25 19 14 15 16 20 NOTE : 2 star section for storing frozen food only. (not freezing) Figure D-1. External Description 1. Freezer temp. control knob 2. Freezer shelf(Freezer tray) 3. Ice cube maker 4. Ice cube box(Ice storage box) 5. Deodorizing unit 6. Fresh case 7. Refrigerator temp. control knob 8. Light(Lamp) 9. Refrigerator shelf (R grass shelf ass'y) 10. Shelf (V grass shelf ass'y) 11. Vegetable crisper(Vegetable case) 12. Divider(V parting plate) 13. Evaporating pan 14. Casters 15. Foot cover(Ventilating grille) 16. Adjustable feet(Adjustable leg ass'y) 17. Fan switch 18. Fan & light switch 19. Utility pocket(Door pocket) 20. Magnetic door seal(Door packing) 21. Egg holder(Egg tray) 22. Egg pocket(R door pocket) 23. Small pocket(R door pocket S) 24. Bottle guard(Bottle stopper) 25. Bottle pocket 26. Plasmacluster panel (Only for SJ-P43N,P47N) Upper hinge cover Mark: Cold air flow Hot pipe Fan motor Panel P.W.B (Only for SJ-P43N,SJ-P47N) Freezer compartment Defrost thermostat Evaporator Freezer temp. control knob Defrost heater Ionizer (Only for SJ-P43N,SJ-P47N) Hot pipe Refrigerator compartment Damper thermostat Refrigerator temp. control knob Drain pipe Vegetable case Evaporating pan Main P.W.B (Only for SJ-P43N,SJ-P47N) Foot cover Compressor Starting relay, Overload relay(Protector) Defrost timer Adjustable leg ass’y Caster Figure D-2. Constructions 6 SJ-P43N/43N SJ-P47N/47N DIMENSIONS OUTER DIMENSIONS AND CLEARANCE more than 60 more than 680 more than 60 1 more than 60 680 73 16 1320 1022.5 1700 1260 9.5 595 90 660 470 1210 1: Not include the handle (Unit : mm) Fig. E-1(SJ-P43N,SJ-43N) more than 60 more than 680 90 more than 1 60 more than 680 60 1320 1820 1260 9.5 595 470 73 16 1142.5 660 1210 1: Not include the handle (Unit : mm) Fig. E-2(SJ-P47N,SJ-47N) 7 SJ-P43N/43N SJ-P47N/47N INNER DIMENSIONS 502 89 229 The dimensions between shelves can be changed by setting the shelves on the other rails. 232 99 242 99 242 536 536 510 307 307 (172) 126 246 225 502 82 349 226 539 508.5 112 118 518 531 (172.5) 89 (133) 502 321 210 502 188 526 (Unit: mm) 502 89 229 Fig. E-3(SJ-P43N,SJ-43N) 232 99 242 510 126 539 502 225 307 307 (192) 536 99 242 82 526 349 226 536 246 628.5 112 118 518 531 (222.5) 89 (183) 502 321 210 502 188 (Unit: mm) Fig. E-4(SJ-P47N,SJ-47N) 8 SJ-P43N/43N SJ-P47N/47N LIST OF ELECTRICAL PARTS ITEMS Thermostat TYPE NAME MM1-8149 Defrost thermostat Thermo. fuse Fan motor Defrost heater Door switch Damper thermostat Defrost timer S101 SF70E 3R00121A MM6-4264 DSD-5 MM1-6173 ND1004M2 Lamp socket Lamp Compressor — — FL1568SD RATING 125V 6A 250V 3A 250V 8A 250V 10A 220-240V 50/60Hz 220-240V 378Ω 250V 0.25A — 220-240V 50/60Hz 250V 1A 240V 15W 220-240V/50Hz SPECIFICATIONS (At normal notch) ON/OFF : -20 / -25˚C Open/Close : 8 / 1˚C Working temp. : 70˚C Working with ø100 fan 140W at 230V 4 terminals push-button type Open/Close : 5 / 0˚C Integration type Cycle time : 10h44m/8h57m(50/60Hz) Delay time : 4m20s/3m37s(50/60Hz) E-12(Hard plastic body type) E-12 Cooling capacity : 188W (50Hz) Main coil : 13.3Ω Common Aux. coil : 25.6Ω (at 25˚C) Aux. coil Starting relay PETOSAT Overload relay(Protector) 1.8C36A1 Ionizer-K(Plasmacluster unit) FTRN-A014CBKZ (Only for SJ-P43N,P47N) — — DC12V 9 22 Ω 300V 3 terminals Open/ Close : 130/60˚C 3.5kV p-p Main coil SJ-P43N/43N SJ-P47N/47N WIRING DIAGRAM Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set. Defrost timer F-Thermostat (BR) (GY) (R) CONNECTED IN TERMINAL BOX TM Lamp CONNECTOR Source Plug MAIN PWB L FM : GRAY : BROWN (live) : ORANGE : YELLOW : RED : PINK : BLUE(neutral) : BLACK : SKY-BLUE : GREEN-YELLOW (earth) : WHITE (W) PC (G-Y) Thermo. fuse DOOR PWB (Y) (BK) Protector (OR) (SB) GY BR OR Y R P BL BK SB G-Y W Fan motor Defrost heater Door switch Compressor Defrost thermo. C M A (BL) Starting relay PC : Plasmacluster unit (Ionizer-K) Figure W-1. Wiring Diagram (SJ-P43N,P47N) Defrost timer (BR) CONNECTED IN TERMINAL BOX F-Thermostat CONNECTOR L FM Thermo. fuse (BK) (Y) Protector Fan motor (SB) : GRAY : BROWN (live) : ORANGE : YELLOW : RED : PINK : BLUE(neutral) : BLACK : SKY-BLUE : GREEN-YELLOW (earth) : WHITE TM Lamp Source Plug GY BR OR Y R P BL BK SB G-Y W (GY) (R) (OR) (W) (G-Y) Defrost heater Door switch Compressor Defrost thermo. C M A (BL) Starting relay Figure W-2. Wiring Diagram (SJ-43N,47N) 10 SJ-P43N/43N SJ-P47N/47N E.V. cover ass’y Cabinet ass’y Lead EV-cover ass’y Fan motor FM F-thermostat Def thermo. ass’y Fuse ass’y F-Door GY-1 OR-1 R-1 BR-1 Y-1 BL-1 BK-1 W-1 1 5 2 6 3 7 4 8 1 5 2 6 3 7 4 8 1 2 (W-1) 1 2 Y-2 1 2 3 1 2 3 DOOR HARNESS 1 2 3 Def. heater ass’y CAB HARNESS PANEL PWB Door switch 2 (PUSH OPEN) 1 (NEUTRAL) 3 (PUSH CLOSE) 4 (PUSH OPEN) 1 2 3 4 BL-2 (OR-1) SB-1 R lamp box ass’y Lamp 15W 1 2 L Lamp socket 1 2 BR-2 (SB-1) 1 2 Terminal box Terminal box B CLUSTER HARNESS PU ORANGE 1 2 3 4 TM 1 2 3 4 (Y-1) (Y-2) (BK-1) (R-1) GY-2 BROWN BLUE 1 2 3 GRAY Defrost timer EARTH OR-4 1 BR-6 2 BL-3 GY-3 3 4 PWB HARNESS MAIN PWB 1 2 Overload relay Terminal block (Protector) GY BR OR Y R P BL BK SB G-Y W : GRAY : BROWN (live) : ORANGE : YELLOW : RED : PINK : BLUE (neutral) : BLACK : SKY-BLUE : GREEN-YELLOW (earth) : WHITE 1 Compressor E C M A BL Source plug / cord Starting relay Figure W-3. Electric Accessories Layout (SJ-P43N,P47N) 11 CLUSTER HARNESS 1 1 2 2 1 2 Plasmacluster unit (Ionizer-K) SJ-P43N/43N SJ-P47N/47N E.V. cover ass’y Cabinet ass’y Lead EV-cover ass’y Fan motor FM F-thermostat Def thermo. ass’y Fuse ass’y Def. heater ass’y GY-1 OR-1 R-1 BR-1 Y-1 BL-1 BK-1 W-1 1 5 2 6 3 7 4 8 1 5 2 6 3 7 4 8 1 2 (W-1) 1 2 Y-2 Door switch 2 (PUSH OPEN) 1 (NEUTRAL) 3 (PUSH CLOSE) 4 (PUSH OPEN) 1 2 3 4 BL-2 (OR-1) SB-1 R lamp box ass’y Lamp 15W L Lamp socket 1 2 1 2 BR-2 (SB-1) Terminal box TM 1 2 3 4 1 2 3 4 (Y-1) (Y-2) (BK-1) (R-1) GY-2 BLUE GRAY EARTH Defrost timer GY BR OR Y R P BL BK SB G-Y W BROWN : GRAY : BROWN (live) : ORANGE : YELLOW : RED : PINK : BLUE (neutral) : BLACK : SKY-BLUE : GREEN-YELLOW (earth) : WHITE Overload relay Terminal block (Protector) 1 Compressor E C M A BL Source plug / cord Starting relay Figure W-4. Electric Accessories Layout (SJ-43N,47N) 12 13 LED1 ZD1 PC R21 (1/2W) 680 SW CN4 2 3 1 CN2 CN3 (MAIN PWB) PC : PLASMACLUSTER UNIT (IONIZER-K) (PANEL PWB) F-FM CN1 2 1 2 3 1 1 7 3 5 R17 (1/2W) 1.8 R11 1K R1 R2 VRS1 C15 100 10V R18 10K C13 0.1 Q3 KTA1046 TRNS C10 1 50V C9 0.1 D7 ISS270A Q1 KRA101M C3 0.1 50V C7 0.1 R7 1K (A/D) 13 C2 2200 35V 10 RS2 RS3 4.7K R20 RS1 R8 10K R19 OPEN I IC1 C16 0.1 O I C19 1000 25V 11 IC2 O G C18 0.1 7805 C5 1 50V C20 100 10V PST993E IC3 3 1 2 C6 0.1 C4 0.1 RS1,2,3=43K(1/2W), RS3=OPEN, VRS1,2=560V RS1,2,3=18K(1/2W), RS3=10K(1/8W), VRS1,2=270V RS1,2,3=18K(1/2W), RS3=SHORT, VRS1,2=270V CST4.00MGW 1M R6 C8 0.1 CF1 C17 100 10V 12 5V [ NOTE ] 1. Resistance which is not specified : 5% 1/8W 2. Rated voltage of the condenser which is not specified : 25V 220 240V 120V 110 120V TMP47C241N IC4 VDD VAREF R40(AINO) K03 K02 R41(AIN1) K01 R42(AIN2) K00 R43(AIN3) R71(WT0) HOLD R80(INT2) RESET XOU R81(T2) XIN R82(INT1) TEST P10 R92 P11 R91 P12 R90 P13 P20 VSS INPUT VOLTAGE C12 0.1 G 7812 12V Figure W-5. Circuit Diagram (Only for SJ-P43N,P47N) R14 1K R5 2.2K R4 10K D3 Q6 KRA101M D4 D6 IN4005E D5 PC1 PC123 Q2 KRC101M R15 4.7K R13 4.7K 12V R9 1K Q7 KRA101M D2 ISS270A R3 Q4 KRC101M R10 2.2K Q5 KRA101M C11 0.1 2A VRS2 12V R16 10K 9 8 7 6 5 C1 0.1 250V 2A D1 IN4007E R12 2.2K 4 3 2 1 HS SJ-P43N/43N SJ-P47N/47N SJ-P43N/43N SJ-P47N/47N FUNCTIONS 1. ADJUSTABLE TEMPERATURE CONTROL (1) Temperature control of freezer Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and cool air circulating fan , and allows the freezer temperature to keep at a suitable temperature. However adjust the freezer temp. control knob as follows depending upon the storing condition of foods. PURPOSE KNOB SETTING MAX(Coldest) For making ice rapidly or fast freezing. When restocking with fresh food. MED For normal freezing. For storing frozen food for a short period (up to one month). When frozen food or ice cream is not stored. MIN Figure F-1. 2 star section for storing frozen food only.(not freezing) (2) Temperature control of refrigerator Damper-thermostat senses temperature of the refrigerator and changes the opening angle of the damper automatically. However, as the Damper-thermostat has no function to switch on or off the compressor and fan motor, the freezer temperature control causes temperature in the refrigerator to vary to some extent. However, adjust the refrigerator temp. control knob as follows depending upon the cooling condition. PURPOSE KNOB SETTING Coldest For keeping freshness of food longer. When the refrigerator does not provide sufficient cooling. MED For normal operation. When the refrigerator provides excessive cooling. MIN Figure F-2. NOTE: The refrigerator temperature is affected also by the freezer temperature. If the freezer temp. control knob is set at the position "MAX", the temperature tends to be lower than the following values, and if set at near the position "MIN", temperature tends to be higher. If the refrigerator is operated for a long time with the freezer temperature control sets the "MAX" position, foods stored in the refrigerator compartment may also freeze. When refrigerator temperature control sets to the "Coldest", some foods stored may freeze. In this case adjust control set back to the "MED" position. When refrigerator temperature control sets to the "Coldest", some foods stored in Fresh case may also become frozen. (3) Reference value of temperature SETTING OF FREEZER TEMP. CONTROL KNOB MAX (Coldest) MED MIN Freezer temperature Approx. -21 C Approx. -18 C 2 star section temperature -15 C -12 C SETTING OF REFRIGERATOR TEMP. CONTROL KNOB Coldest MED MIN Approx. -15 C Refrigerator temperature Approx. 0 Approx. 3 Approx. 6 -9 C Fresh case temperature Approx. -3 Approx. 1 Approx. 4 The values shown above refer to the case where the freezer temp. control knob is set at "MED". The values shown above refer to the measurement carried out center area and 1/3 of overall height from the bottom at each of the refrigerator and the freezer after machine has been operated at an ambient temperature of 30˚C with no food stored and the door closed until the temperature is stabilized. The values vary depending upon frequency of opening and closing the door, ambient temperature, amount of stored foods and manner of storing foods. 14 SJ-P43N/43N SJ-P47N/47N 2. DEFROSTING (1) No defrosting operation is necessary No defrosting operation is necessary. As this machine is so designed that a built-in evaporator cools air and a fan circulates cooled air, neither the freezer nor the refrigerator is frosted, though the evaporator is frosted. The frosted evaporator is defrosted automatically due to the function of defrosting timer and heater, requiring no defrosting operation. (2) Where is melted frost brought 1. Melted frost is brought into the evaporating pan at the back of the set and is evaporated here by the heat of compressor. 2. Be sure to use Evaporating pan as inserted so as to be level with the outer case. (3) The following circuit diagrams in the table show automatic defrosting function of the refrigerator with timer and defrost thermostat. Operation 1. Cooling (Normal) Electric diagram Defrost thermostat ON Compressor running Timer motor running Thermo. fuse Defrost heater TM Defrost thermostat (ON) COMP Compressor Timer contact Timer motor SOURCE Thermostat Description The integration timer integrates running time of the compressor. When it reaches cycle time of defrost timer, the timer contact is changed to start defrosting. Figure F-3. Defrost thermostat ON (Time 20 to 30 min.) Thermo. fuse Defrost heater TM Defrost thermostat (ON) COMP Compressor Thermostat SOURCE Compressor stops Timer motor stops Timer contact Timer motor 2. Defrosting The timer contact is changed to start defrosting, the timer motor stops, and power is supplied to the defrost heater. It takes about 20 to 30 min. to defrost. When little frosted, the defrosting takes little time. When much frosted, the defrosting takes much time. Figure F-4 . Defrost thermostat OFF Thermo. fuse Defrost heater TM Defrost thermostat (OFF) COMP Compressor Thermostat SOURCE Compressor stops Timer motor running Timer contact (Time approx. 5 min.) Timer motor 3. Drain When the defrost thermostat becomes OFF, the timer motor starts running. During the operation time (delay time of defrost time) defrosted water is drained outside the refrigerator. Figure F-5. Defrost thermostat OFF SOURCE Thermostat Compressor running Timer motor stops Timer contact Thermo. fuse Defrost heater TM Defrost thermostat (OFF) Figure F-6. 15 COMP Compressor (Time approx. 5 min.) Timer motor 4. Restart Timer contact is changed to cooling operation and the compressor starts running and the timer motor stops. Defrost thermostat contact becomes ON when it’s cooled. And the timer motor starts running. (Figure F-3.) SJ-P43N/43N SJ-P47N/47N (4) As a reference to determine the causes of trouble, malfunction and phenomena are described below. Refer to the following when repairing. 1. Disconnection of defrost heater As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is started, the freezer temperature rises and a portion of ice and stored foods are melted. 2. Melted thermo. fuse or opened-circuit due to the defect of defrost thermostat. When the above mentioned trouble occurs in cooling operation, the timer motor does not run, defrosting will not take place, and consequently freezing is caused. In the above mentioned condition, when the timer shaft is turned by hand to defrost, the timer motor runs during the operation time. However, the motor stops from the time when the contact is changed, and freezing causes. NOTE: As the thermo. fuse assembly is intended to prevent dangers, do not use it under shorted condition even for a short period. 3. DEW PREVENTION The hot pipe, namely D.P.-condenser, is arranged around the flange part of cabinet and the C-partition plate, preventing dew from being generated on the cabinet. NOTE: D.P.-condenser pipe may be felt hot if touched by hand while the compressor is in operation. If you are asked about this, please explain that the hot pipe serve to prevent the dew generation. Hot pipe Figure F-7 4. INSPECTION OF INITIAL STARTING (1) Inspection of cooling unit 1. Set the temperature control knob to "MAX" and check that the compressor starts to operate. 2. Depress the door switch to run the fan and check that cool air is blown out of the cold air outlet of the freezer and the refrigerator. 3. When the compressor does not work, check that the timer is not set to "defrost" position. 4 It takes about an hour and a half or two hours to put food in the refrigerator after starting operation. NOTE: After return the temperature control knob to "MED" position. When the refrigerator is operated initially after installed, the compressor may vibrate excessively for 1 to 2 min. However, vibration becomes normal if it is continuously operated. (2) Inspection of defrost device Operate the refrigerator for 20 to 30 min. and then check the defrost device in the following procedures : Allow 5 min. to restart the compressor since immediate starting after stopping will cause unsmooth operation. 1. Turn the timer shaft clockwise with a screw driver. At this time, make certains the timer clinks and the compressor stops. 2. After more than 5 min., turn the shaft further to operate. Make certain cooling operation is started again. 16 SJ-P43N/43N SJ-P47N/47N 5. PLASMACLUSTER (Only for SJ-P43N,P47N) (1) Plasmacluster is what thing. The ionizer inside the refrigerator will release cluster ions, which are collective mass of positive and negative ions, into the the freezer and refrigertor compartments. The cluster ions inactivate airborne fungus. (2) Plasmacluster Panel 1.When the refrigerator will be operated, the Plasmacluster lamp of the panel will light up. 2.By pushing the button, the lamp goes out or lights up. 3.Under the lamp is lighting, Plasmacluster operation is controlled as follows. Plasmacluster panel Lamp Plasmacluster Button (3) Plasmacluster Control. 1.Plasmacluster operation will be performed when the following conditions gather. 1) Lamp : Under lighting 2) Compressor : Under operation 3) Door : Closed 4) Within "The Plasmacluster operation time". 2.If the sum total of Plasmacluster operation time will reach at the set time ("The Plasmacluster operation Time") , Plasmacluster operation will stop. 3.After an operation stop, the Plasmacluster will be not operated during the set time ("The Plasmacluster operation compulsive stop time") . Time chart A Compressor ON Fan motor Door Plasmacluster t1 t2 t3 Time chart B Compressor Fan motor Door Plasmacluster t1 t2 t3 The Plasmacluster operation time = t1 + t2 + t3 17 SJ-P43N/43N SJ-P47N/47N ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING. 1. R-AIR GUIDER ASSEMBLY A-sealer ag1 Damper thermo. Thermo. cap. sealer R air guider S Plasma holder (Only for SJ-43N,SJ-47N) A-sealer ag3 Ionizer-K A-sealer ag2 Dial sealer Plasma harness (Only for SJ-P43N,SJ-P47N) R air guider Figure A-1 Less than 160 mm (1) Forming sensor of Damper thermo. Less than 12 mm 8 +1 mm 5 +1 mm Damper thermostat NOTE Minimum bending radius is R5mm. There should be no gas leak by reforming of sensor tube. After forming, fix it to the refrigerator. Figure A-2 (2) Setting R air guider S (Only for SJ-43N,SJ-47N) and sticking sealers to R air guider. R air guider S (Only for SJ-43N,47N) A-sealer ag1 R air guider A-sealer ag1 Masking tape OVERLAP 15mm R air guider A-sealer ag2 A-sealer ag1 A-sealer ag2 Dial sealer A-sealer ag1 Figure A-3 18 A-sealer ag3 OVERLAP AREA DATUM DATUM OVERLAP 8mm OVERLAP 15mm DATUM SJ-P43N/43N SJ-P47N/47N (3) Fixing of the Ionizer-K.(Only for SJ-P43N,P47N) (3)-1 Connect Ionizer-K and connector of the lead wire. (3)-2 Insert Ionizer-K to Plasma holder. (3)-3 Insert the (3)-2 assembly to R air guider A. R air guider A Plasma harness Ionizer-K 2P Connector should insert surely. Plasma harness Plasma holder Ionizer-K A Paper tape W30×100mm B B Paper tape W30×40mm 2P 2P 2P A SEC. A—A Paper tape W30×40mm SEC. B—B 19 SJ-P43N/43N SJ-P47N/47N 2. FAN LOUVER AND E.V COVER ASSEMBLY 2-1. How to remove the Fan louver (1) Take out 2 screws. (2) Insert the screwdriver into the air hole of the Fan louver. (3) Press the Fan louver to the left side with the screwdriver,and pull it toward yourself to take off the Fan louver. (4) Fan louver Claw (4) Claw (1) Screw (4) Claw (3) (3) Claw (1) Screw (2) Figure A-4 2-2. E.v cover assembly Motor cushion Fan motor holder B Fan motor holder A E.v cover sealer C Defrost thermo. ass’y L-band C E.v cover Propeller fan 100 Fan motor Fan clamp U-sealer handle E.v cover sealer G Lead EV-cover ass’y E.v cover sealer F E.v cover sealer C E.v cover sealer A E.v cover AL A L-band C E.v cover sealer B F-thermostat Fuse ass’y E.v cover sealer E E.v cover sealer D Figure A-5 (1) Sticking of Sealers to E.V cover (2) Fixing of Fan motor and Fan (2)-1 Stick U-sealer handle to Fan motor holder A. Fan motor holder A E.v cover sealer A C 7 + 2mm E.v cover sealer C STICK START STICK START E.v cover 0 + 1mm E.v cover sealer G U-sealer handle STICK START E.v cover sealer B SEC. C-C [back side] Figure A-7 Figure A-6 20 C U-sealer handle SJ-P43N/43N SJ-P47N/47N (2)-2 Insert the terminals of Lead EV-cover ass'y to Fan motor. (2)-3 Fix two Motor cushions to Fan motor, and set it at Fan motor holder A and B. Then fix with Tapping screw. (2)-4 Set Fan clamp to Propeller fan 100 and insert it to the shaft of Fan motor. Fan clamp Fan motor holder B D Fan clamp Motor cushion Fan motor holder A Slit of each Fan clamp and Propeller fan should not be at same position. Slit Fan clamp Propeller fan 100 Tapping screw Propeller fan Fan motor ○ × 4 + 0.5mm Note Propeller fan should not be taken out from shaft when pulled by 3 kgf. Shaft Lead EV-cover ass’y RED Detail of D BROWN Figure A-8 Figure A-9 (3) Setting of Fan motor ass'y , Defrost thermo. ass'y and Fuse ass'y. E.v cover Lead e.v cover ass’y Tapping screw L-band C more than 3.5mm more than 3.5mm Aluminum tape L-band C F E.v cover sealer C Take out lead wire from square hole to front and fix with L-band C, then seal with E.v cover sealer C F Tapping screw Set metal side below [front side] Defrost thermo. ass’y H Aluminum tape E.v cover sealer F G H Fuse ass’y E.v cover AL A Aluminum tape Turn up lead wire CUT Fuse ass’y ATTENTION Defrost thermo. ass’y E.v cover sealer E 10 + 5mm [back side] Aluminum tape L-band C Detail of G Not come out of claw. SEC. F F SEC. H H E.v cover sealer E [Front side] Figure A-10 21 SJ-P43N/43N SJ-P47N/47N (4) Inserting of pins After inserting, fix with vinyl tape. F-thermostat 2 (RED, inserted) Defrost thermo. 3 (PINK) Fuse 8 (WHITE) Fan motor 1 , 5 WIRE COLOR FOR FAN MOTOR 100-110V : WHITE 127V : YELLOW 220-240V : BLUE 1 2 3 4 5 6 7 8 F-thermostat 6 (BROWN, inserted) Vinyl tape Fuse 8 (BLACK) Defrost thermo. 7 (BLUE) Note Pins should be inserted surely, and check by pulling it. Figure A-11 Figure A-12 (5) Setting of F-thermostat (5)-3 Set to E.V cover. Stick E.v cover sealer D. (5)-1 Form capillary tube of F-thermostat. E.v cover sealer D 21mm B R10mm R10mm Note F-thermostat • Bending radius of capillary tube should be from R5mm to R10mm. 8.5mm 50mm Figure A-13 (5)-2 Insert terminal of Lead EV-cover ass'y. B SEC. B B RED (front side) BROWN Figure A-15 (back side) Figure A-14 22 SJ-P43N/43N SJ-P47N/47N (2) Replacement of Def. heater ass'y. (2)-1 Remove the center screw of Drain support al to take it off from the food liner. 3. DEFROST HEATER (1) Taking-out Evaporator (1)-1. Take out E.v cover ass'y (Fig. A-16). Drain support al Evaporator Screw Food liner convex part Fig. A-19 Fig. A-16 (2)-2 Raise the protrusion part of Drain support al. Then remove Heater cover. (1)-2. As shown in Fig. A-17, pull the upper part of Evaporator toward you, pull it diagonally so that the pipe of Evaporator does not contact the convex part of food liner. Protrusion parts Food liner convex part Drain support al Evaporator Pipe Heater cover Protrusion part of Drain support al(2 pcs.) Fig. A-17 (1)-3. As shown in Fig. A-18, bend the removed Evaporator horizontally so that Defrost heater can be replaced easily. NOTE: When pulling Evaporator and bending the pipes, pay attention so as not to break and deform the pipes. Still, take care not to hurt yourself by fin of Evaporator. Def. heater ass’y Heater cover Fig. A-20 (2)-3 Open Def.heater fixed part of Drain support al to the right and left, then remove Def.heater ass'y. Evaporator Fixed parts Fig. A-18 Drain support al Def.heater ass’y Fig. A-21 23 SJ-P43N/43N SJ-P47N/47N (2)-4. Replace Def. heater ass'y with new one. (2)-7. Stick the longer wire to the Drain support by aluminum tape (2 pieces), and wind vinyl tape (2 pieces) to lead wires of Def. heater ass'y by aluminum tape as shown in Fig. A-25. Note: Glass cloth tape part shall be both side of Drain support to protect the lead wire from damaged. Heater cover Glass cloth tape Glass cloth tape Def.heater ass’y A A Sec. AA [back side] aluminum tape (W25 X L40) Drain support al Fig. A-22 Glass cloth tape Glass cloth tape (2)-5. Wind the Glass cloth tape (3M: No. 27) to lead wire of Def. heater ass'y. (2 places) (more than 2 turns) [bottom side] Fig. A-25 Def. heater ass’y 360 + 5 (2)-8. Set Heater cover on Drain support, and bend top edge c and d to outside as shown in Fig. A-26. (40) (40) 50 + 5 Heater cover top edge Glass cloth tape (W40 x L25) Def.heater ass’y Drain support al Lead wire Heater cover Glass cloth tape Wind the Glass cloth tape more than 2 turns. c Sec. BB Fig. A-23 B d (2)-6. Bend a and b of Drain support al to right angle (90˚) to set Def. heater ass'y. (Fig. A-24) Def.heater ass’y B Fig. A-26 This side is longer wire (2)-9. Wind up Leading wire sealer as shown in Fig. A-27 a This side is shorter wire Drain support al Heater cover Leading wire sealer Drain support al 0 19 Def.heater ass’y 0 +2 b Def.heater ass’y Fig. A-24 Fig. A-27 (2)-10. Set the assembly above on the food liner by fixing a screw. 24 SJ-P43N/43N SJ-P47N/47N (3) Installing of Evaporator (3)-1. Install Evaporator as shown in Fig. A-16 in the reverse order of Fig. A-17. (3)-2. Correct the deformed fin. NOTE 1. When installing Evaporator, take care not to deform significantly and break the pipes. 2. Take care not to damage the lead wires and hurt yourself by the fin of Evaporator. COOLING UNIT Mark: Refrigerant flow Mark: Brazing portion Hot pipe L (Side condenser) Hot pipe (DP-condenser) Hot pipe R (Side condenser) Evaporator Back condenser Suction pipe Eva-pan pipe Compressor Capillary tube Dryer Figure C-1. Cooling unit 25 SJ-P43N/43N SJ-P47N/47N Dryer Capillary tube Charge pipe Hot pipe Evaporator Charge pipe Compressor Suction pipe S.P. connector Eva-pan pipe Back condenser Figure C-2. Location From Eva-pan pipe ass’y to Back condenser In From Back condenser out to Hot pipe From Compressor to Discharge p connector From Suction pipe to SP connector From Hot pipe to Dryer From Dryer to Capillary tube From SP connector to Compressor From Compressor to Charge pipe Figure C-3. Location 26 From Discharge p connector to Eva-pan pipe ass’y SJ-P43N/43N SJ-P47N/47N REPLACEMENT PARTS LIST(SJ-P43N/43N-SL1/WH1) REF. NO. PART NO. DESCRIPTION Q'TY CODE SJ-P43N SJ-P43N SJ-43N -SL1 -WH1 -SL1 SJ-43N -WH1 ELECTRIC PARTS 11111111111111111111- 1 2 3 4 5 6 7 8 9 10 11 17 20 21 22 33 45 46 50 55 RTHM-A103CBZZ RSTT-A134CBE0 QSWTDA047CBZZ PDMP-A050CBEZ FTHM-A039CBKZ RMOTRA046CBE0 QSOCAA084CBEZ RLMP-A029CBEZ QACC-A156CBZZ QSW-PA090CBZA RHOG-A161CBZZ FFS-TA061CBKZ FW-VZA146CBEZ FHETBA161CBEZ FCNW-A733CBKZ QCNW-A886CBE0 FTRN-A014CBKZ QCNW-B104CBZZ FPWB-A337CBKZ FPWB-A336CBKZ F-themostat Starting relay Defrost timer Damper thermo Defrost thermo.ass’y Fan motor Lamp socket Lamp15w Source cord Door switch Protector Fuse ass’y Lead ev-cover ass’y Def.heater ass’y Relay wire ass’y Olr cord Ionaizer-k Plasma harness Main pwb Panel pwb ass’y 222222222222222222222222222222222222222222222222222- 2 4 7 7- 1 7- 2 8 8- 2 13 14 15 16 17 19 20 21 22 23 24 26 27 28 29 29 29 31 38 38 39 43 44 45 46 47 49 50 55 56 57 63 64 65 66 67 68 69 70 71 72 73 77 78 JKNB-A036CBFC LANG-A059CBPZ FLEGPA083CBKZ FAJS-A015CBKZ LHLD-A533CBPZ FLEGPA084CBKZ LHLD-A534CBPZ DHNG-A437CBMZ DHNG-A419CBMZ DHNG-A418CBMZ GCOV-A210CBFZ LCRA-A022CBPZ LHLD-A389CBF0 NFANPA011CBF0 PSEL-C067CBEZ PSEL-C068CBEZ PSEL-C066CBEZ PCOVPA308CBFA PCOV-A277CBFA GCOVPA142CBRA HGRL-A206CBRA GCOV-A228CBFA GCOV-A228CBFF GCOV-A228CBFH JKNB-A033CBFC PGID-A161CBFZ PGID-A168CBFZ PGID-A162CBFZ LPLTPA323CBMA HGRL-A237CBFA HGRL-A238CBFA PFIL-A050CBEZ LHLD-A672CBFZ LSTPPA108CBFA LSTPPA118CBFA HGRL-A209CBFA PFPFPB345CBFZ PSEL-C095CBEZ LHLD-A484CBFA LHLD-A485CBFA PSEL-B209CBE0 PSHEMA225CBPZ LPLTMA633CBPZ PSEL-A415CBE0 PSEL-C069CBEZ PSEL-C135CBEZ PSEL-A552CBE0 PSEL-C078CBEZ PSEL-C079CBEZ LHLD-A391CBE0 LPLTMA399CBP0 F-temp. control knob Eva holder 47 Leg holder l ass’y Adjustable leg ass’y Leg holder l Leg holder r ass’y Leg holder r Upper hinge ass’y Bottom hinge r ass’y Center hinge r ass’y E.v cover Fan clamp Motor cushion Propeller fan 100 E.v cover sealer a E.v cover sealer b E.v cover sealer c Terminal cover R lamp cover R-c box cover Fan louver Upper hinge cover Upper hinge cover Upper hinge cover R-temp.control knob R-air guider R-air guider R-air guider s Panel base F deodo.louver R deodo.louver Deodorizer Plasma holder Chilled stopper Case stopper v Multi louver s R-louver insu.s A-sealer r-louver Fan motor holder b Fan motor holder a U-sealer handle Heater cover Drain support al E.v cover sealer c E.v cover sealer d E.v cover sealer e Dial sealer A-sealer ag1 A-sealer ag2 Sl-5n clip Dryer support 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - AV AS AZ AW AM AZ AL AH AQ AS AX AM AL AY AP AE AZ AF BC AT 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 AC AC AF AE AL AF AP AE AD AE AR AC AF AD AA AA AC AE AE AQ AS AE AF AE AC AG AK AC AN AE AC AM AE AC AC AM AE AB AH AH AB AC AF AC AA AC AC AC AB AD AD MECHANICAL PARTS 27 SJ-P43N/43N SJ-P47N/47N REF. NO. PART NO. DESCRIPTION Q'TY CODE SJ-P43N SJ-P43N SJ-43N -SL1 -WH1 -SL1 2222222222222- 79 80 81 82 83 87 91 93 94 95 99 100 101 LBND-A019CBE0 PBOX-A132CBFA PBOX-A143CBFA PCOVPA373CBFA PSEL-C080CBEZ LBND-A018CBE0 HGRL-A202CBFA PCAP-A068CBFA PSEL-C137CBEZ PSHEMA231CBEZ PSEL-A562CBE0 PSEL-C138CBEZ PSEL-C139CBEZ Nylon band Terminal box Terminal box-b Terminal cover-b A-sealer ag3 Fastening band a F return cover C sliding cap a E.v cover sealer f Ev cover al a Leading wire sealer E.v cover sealer g Ev-insulation 47 SJ-43N -WH1 1 1 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 4 1 1 1 1 2 AB AF AH AN AA AP AF AC AB AC AC AA AC 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 - BS BS BS BU AD AC AD AK AN AN AT AH AN AD AH AM BU BT BS BS AD AC AF AV AN AP AD AK BA AH 4 8 8 1 4 4 8 8 1 4 4 8 2 1 1 4 4 8 2 1 1 4 AC AC AH AH AC AB 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 AR AH AM AL AH AS AT AN AN AM AG AX AL AV AN AR AU AS AR AW AS DOOR PARTS 333333333333333333333333333333- 5 5 5 5 5- 1 5- 2 5- 3 5- 4 5- 5 5- 5 6 7 8 9 10 11 15 15 15 15 15- 1 15- 2 15- 3 17 19 20 21 22 30 31 FDORFB832CBKZ FDORFB833CBKZ FDORFB847CBKZ FDORFB848CBKZ LSTPPA131CBFA NBRGPA033CBFA LSTPMA008CBM0 GDAI-A071CBMZ HBDGDA946CBEA HBDGDA946CBEC FPACGA346CBKZ HDECQA475CBMA HDECQA476CBRA LPLTMA686CBPZ LPLTPA374CBFA HDECQA478CBMA FDORRB640CBKZ FDORRB642CBKZ FDORRB661CBKZ FDORRB662CBKZ LSTPPA084CBFA NBRGPA022CBFA LSTP-A058CBM0 FPACGA348CBKZ HDECQA477CBRA HDECQA479CBMA LPLTMA687CBPZ LPLTPA375CBFA GCOVPA177CBRA HBDG-A005CBEA F-door ass’y F-door ass’y F-door ass’y F-door ass’y Fd-stopper spring r Nylon bearing 3f F-door stopper r Badge base Badge Badge F-door packing Hd cap Handle trim f Hd support f Handle base f Hd cover ft R-door ass’y R-door ass’y R-door ass’y R-door ass’y Rd-stopper spring r Nylon bearing 3s R-door stopper r R-door packing Handle trim r Hd cover rb Hd support r Handle base r Panel cover Pc badge 444444- 1 3 11 12 15 17 LBND-A023CBE0 LX-VZA022CBZZ QTAN-A012CBE0 QTAN-A013CBE0 LX-BZA090CBZZ LX-WZA035CBZZ L-band c Special screw Solderless term. b Solderless term. a Special screw Washer 555555555555555555555- 1 2 3 4 5 6 9 13 13 14 15 16 17 18 19 24 242425 2525- UPOK-A180CBRA UPOKPA268CBFA UPOK-A179CBRA UPOK-A181CBRA UTNA-A282CBFA FSRA-A193CBYZ USRA-A270CBFA HGRL-A239CBFA HGRL-A239CBFC USRA-A268CBFA GGAD-A032CBFA UYOK-A401CBFA UYOK-A399CBFA UYOK-A400CBFA GDORPA072CBRA FTNA-A394CBKZ UTNA-A377CBEZ UWAKPA014CBFA FTNA-A395CBKZ UTNA-A378CBEZ UWAKPA015CBFA Bottle pocket R door pocket s Door pocket R door pocket Egg tray Ice cube maker Freezer tray Ventilating grille Ventilating grille Evaporating pan V parting plate Vegetable case Ice storage box Fresh case Fresh door hs R glass shelf ass’y Glass shelf r G guard r V glass shelf ass’y Glass shelf v G guard v OTHER PARTS ATTACHMENT PARTS 1 2 1 2 28 SJ-P43N/43N SJ-P47N/47N REF. NO. PART NO. DESCRIPTION Q'TY CODE SJ-P43N SJ-P43N SJ-43N -SL1 -WH1 -SL1 5- 31 5- 32 5- 35 LRALPA136CBFA LRALPA137CBFA UPOKPA269CBFA Ice tray holder l Ice tray holder r Bottle stopper 666666666666666- PCMPLA215CBEZ PSPAGA042CBE0 FFRM-A120CBKZ FDRY-A006CBK0 PCLI-A050CBE0 PSPAFA034CBE0 PPIPCA386CBEZ PPIPCA252CBE0 FPIPCA172CBKZ PCOVPA246CBE0 PGUM-A004CBF0 QTAN-A045CBE0 FPIPCA162CBKZ LANG-A058CBPZ PGUM-A003CBF0 Compressor Rubber grommet Base frame ass’y Dryer ass’y Clip Sleeve S.p connector Charge pipe Discharge p. ass’y Terminal cover Absorbent rubber a Terminal block Eva pan pipe s ass’y Absorbent rubber clm Absorbent rubber b TINS-A684CBRZ TLAB-A876CBRZ SPAKCA167CBZZ CPADBA799YDKZ CPADBA057CBKZ SPADBA190CBFZ SPADBA191CBFZ SPADBC435YDEZ SPADBC436YDEZ TLAB-B274CBRZ TLAB-A637CBR0 TLAB-A638CBR0 TLAB-A639CBR0 TLAB-A640CBR0 TLAB-A641CBR0 TLAB-A642CBR0 TLAB-A643CBR0 TLAB-A644CBR0 TLAB-A985CBRZ TLAB-A939CBRZ TINS-A682CBRZ Operation manual Warning label Packing case 43n Bottom pad ass’y Top pad ass’y Corner post fl Corner post fr Corner post bl Corner post br Energy label Energy label (GB) Energy label (D) Energy label (F) Energy label (E) Energy label (I) Energy label (GR) Energy label (P) Energy label (NL) Two star label Caution label rof Caution sheet weee SJ-43N -WH1 1 1 1 1 1 1 1 1 1 1 1 1 AG AG AC 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 BW AE AG AX AD AD AF AD AM AL AH AQ AS AC AH 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AF AC AZ AV AR AK AL AG AG AE AG AG AG AG AG AG AG AG AF AD AC CYCLE PARTS 1 2 4 5 6 9 11 18 19 21 24 25 26 28 29 MISCELLANEOUS 909090909090909090909090909090909090909090- 1 2 3 6 7 8 9 10 11 12 13 13 13 13 13 13 13 13 19 21 34 HOW TO ORDER REPLACEMENT PARTS To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 3. PART NO. 2. REF. NO. 4. DESCRIPTION 29 SJ-P43N/43N SJ-P47N/47N REPLACEMENT PARTS LIST(SJ-P47N/47N-SL1/WH1) REF. NO. PART NO. DESCRIPTION Q'TY CODE SJ-P47N SJ-P47N SJ-47N -SL1 -WH1 -SL1 SJ-47N -WH1 ELECTRIC PARTS 11111111111111111111- 1 2 3 4 5 6 7 8 9 10 11 17 20 21 22 33 45 46 50 55 RTHM-A103CBZZ RSTT-A134CBE0 QSWTDA047CBZZ PDMP-A050CBEZ FTHM-A039CBKZ RMOTRA046CBE0 QSOCAA084CBEZ RLMP-A029CBEZ QACC-A156CBZZ QSW-PA090CBZA RHOG-A161CBZZ FFS-TA061CBKZ FW-VZA146CBEZ FHETBA161CBEZ FCNW-A733CBKZ QCNW-A886CBE0 FTRN-A014CBKZ QCNW-B104CBZZ FPWB-A337CBKZ FPWB-A336CBKZ F-themostat Starting relay Defrost timer Damper thermo Defrost thermo.ass’y Fan motor Lamp socket Lamp15w Source cord Door switch Protector Fuse ass’y Lead ev-cover ass’y Def.heater ass’y Relay wire ass’y Olr cord Ionaizer-k Plasma harness Main pwb Panel pwb ass’y 222222222222222222222222222222222222222222222222222- 2 4 7 7- 1 7- 2 8 8- 2 13 14 15 16 17 19 20 21 22 23 24 26 27 28 29 29 29 31 38 38 39 43 44 45 46 47 49 50 55 56 57 63 64 65 66 67 68 69 70 71 72 73 77 78 JKNB-A036CBFC LANG-A059CBPZ FLEGPA083CBKZ FAJS-A015CBKZ LHLD-A533CBPZ FLEGPA084CBKZ LHLD-A534CBPZ DHNG-A437CBMZ DHNG-A419CBMZ DHNG-A418CBMZ GCOV-A210CBFZ LCRA-A022CBPZ LHLD-A389CBF0 NFANPA011CBF0 PSEL-C067CBEZ PSEL-C068CBEZ PSEL-C066CBEZ PCOVPA308CBFA PCOV-A277CBFA GCOVPA142CBRA HGRL-A206CBRA GCOV-A228CBFA GCOV-A228CBFF GCOV-A228CBFH JKNB-A033CBFC PGID-A161CBFZ PGID-A168CBFZ PGID-A162CBFZ LPLTPA323CBMA HGRL-A237CBFA HGRL-A238CBFA PFIL-A050CBEZ LHLD-A672CBFZ LSTPPA108CBFA LSTPPA118CBFA HGRL-A205CBFA PFPFPB334CBFZ PSEL-C085CBEZ LHLD-A484CBFA LHLD-A485CBFA PSEL-B209CBE0 PSHEMA225CBPZ LPLTMA633CBPZ PSEL-A415CBE0 PSEL-C069CBEZ PSEL-C135CBEZ PSEL-A552CBE0 PSEL-C078CBEZ PSEL-C079CBEZ LHLD-A391CBE0 LPLTMA399CBP0 F-temp. control knob Eva holder 47 Leg holder l ass’y Adjustable leg ass’y Leg holder l Leg holder r ass’y Leg holder r Upper hinge ass’y Bottom hinge r ass’y Center hinge r ass’y E.v cover Fan clamp Motor cushion Propeller fan 100 E.v cover sealer a E.v cover sealer b E.v cover sealer c Terminal cover R lamp cover R-c box cover Fan louver Upper hinge cover Upper hinge cover Upper hinge cover R-temp.control knob R-air guider R-air guider R-air guider s Panel base F deodo.louver R deodo.louver Deodorizer Plasma holder Chilled stopper Case stopper v Multi louver l R-louver insu.l A-sealer r-louver Fan motor holder b Fan motor holder a U-sealer handle Heater cover Drain support al E.v cover sealer c E.v cover sealer d E.v cover sealer e Dial sealer A-sealer ag1 A-sealer ag2 Sl-5n clip Dryer support 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - AV AS AZ AW AM AZ AL AH AQ AS AX AM AL AY AP AE AZ AF BC AT 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 AC AC AF AE AL AF AP AE AD AE AR AC AF AD AA AA AC AE AE AQ AS AE AF AE AC AG AK AC AN AE AC AM AE AC AC AM AE AC AH AH AB AC AF AC AA AC AC AC AB AD AD MECHANICAL PARTS 30 SJ-P43N/43N SJ-P47N/47N REF. NO. PART NO. DESCRIPTION Q'TY CODE SJ-P47N SJ-P47N SJ-47N -SL1 -WH1 -SL1 2222222222222- 79 80 81 82 83 87 91 93 94 95 99 100 101 LBND-A019CBE0 PBOX-A132CBFA PBOX-A143CBFA PCOVPA373CBFA PSEL-C080CBEZ LBND-A018CBE0 HGRL-A202CBFA PCAP-A068CBFA PSEL-C137CBEZ PSHEMA231CBEZ PSEL-A562CBE0 PSEL-C138CBEZ PSEL-C139CBEZ Nylon band Terminal box Terminal box-b Terminal cover-b A-sealer ag3 Fastening band a F return cover C sliding cap a E.v cover sealer f Ev cover al a Leading wire sealer E.v cover sealer g Ev-insulation 47 SJ-47N -WH1 1 1 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 4 1 1 1 1 2 AB AF AH AN AA AP AF AC AB AC AC AA AC 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 - BS BS BS BU AD AC AD AK AN AN AT AH AN AD AH AM BW BU BU BS AD AC AF AV AN AP AD AK BA AH 4 8 8 1 4 4 8 8 1 4 4 8 2 1 1 4 4 8 2 1 1 4 AC AC AH AH AC AB 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 AR AH AM AL AH AS AT AN AN AM AG AX AL AV AN AR AU AS AR AW AS DOOR PARTS 333333333333333333333333333333- 5 5 5 5 5- 1 5- 2 5- 3 5- 4 5- 5 5- 5 6 7 8 9 10 11 15 15 15 15 15- 1 15- 2 15- 3 17 19 20 21 22 30 31 FDORFB832CBKZ FDORFB833CBKZ FDORFB847CBKZ FDORFB848CBKZ LSTPPA131CBFA NBRGPA033CBFA LSTPMA008CBM0 GDAI-A071CBMZ HBDGDA946CBEA HBDGDA946CBEC FPACGA346CBKZ HDECQA475CBMA HDECQA476CBRA LPLTMA686CBPZ LPLTPA374CBFA HDECQA478CBMA FDORRB639CBKZ FDORRB641CBKZ FDORRB659CBKZ FDORRB660CBKZ LSTPPA084CBFA NBRGPA022CBFA LSTP-A058CBM0 FPACGA347CBKZ HDECQA477CBRA HDECQA479CBMA LPLTMA687CBPZ LPLTPA375CBFA GCOVPA177CBRA HBDG-A005CBEA F-door ass’y F-door ass’y F-door ass’y F-door ass’y Fd-stopper spring r Nylon bearing 3f F-door stopper r Badge base Badge Badge F-door packing Hd cap Handle trim f Hd support f Handle base f Hd cover ft R-door ass’y R-door ass’y R-door ass’y R-door ass’y Rd-stopper spring r Nylon bearing 3s R-door stopper r R-door packing Handle trim r Hd cover rb Hd support r Handle base r Panel cover Pc badge OTHER PARTS 444444- 1 3 11 12 15 17 LBND-A023CBE0 LX-VZA022CBZZ QTAN-A012CBE0 QTAN-A013CBE0 LX-BZA090CBZZ LX-WZA035CBZZ L-band c Special screw Solderless term. b Solderless term. a Special screw Washer 555555555555555555555- 1 2 3 4 5 6 9 13 13 14 15 16 17 18 19 24 242425 2525- UPOK-A180CBRA UPOKPA268CBFA UPOK-A179CBRA UPOK-A181CBRA UTNA-A282CBFA FSRA-A193CBYZ USRA-A270CBFA HGRL-A239CBFA HGRL-A239CBFC USRA-A268CBFA GGAD-A032CBFA UYOK-A401CBFA UYOK-A399CBFA UYOK-A400CBFA GDORPA072CBRA FTNA-A394CBKZ UTNA-A377CBEZ UWAKPA014CBFA FTNA-A395CBKZ UTNA-A378CBEZ UWAKPA015CBFA Bottle pocket R door pocket s Door pocket R door pocket Egg tray Ice cube maker Freezer tray Ventilating grille Ventilating grille Evaporating pan V parting plate Vegetable case Ice storage box Fresh case Fresh door hs R glass shelf ass’y Glass shelf r G guard r V glass shelf ass’y Glass shelf v G guard v ATTACHMENT PARTS 1 2 1 2 31 SJ-P43N/43N SJ-P47N/47N REF. NO. PART NO. DESCRIPTION Q'TY CODE SJ-P47N SJ-P47N SJ-47N -SL1 -WH1 -SL1 5- 31 5- 32 5- 35 LRALPA136CBFA LRALPA137CBFA UPOKPA269CBFA Ice tray holder l Ice tray holder r Bottle stopper 666666666666666- PCMPLA215CBEZ PSPAGA042CBE0 FFRM-A120CBKZ FDRY-A006CBK0 PCLI-A050CBE0 PSPAFA034CBE0 PPIPCA386CBEZ PPIPCA252CBE0 FPIPCA172CBKZ PCOVPA246CBE0 PGUM-A004CBF0 QTAN-A045CBE0 FPIPCA162CBKZ LANG-A058CBPZ PGUM-A003CBF0 Compressor Rubber grommet Base frame ass’y Dryer ass’y Clip Sleeve S.p connector Charge pipe Discharge p. ass’y Terminal cover Absorbent rubber a Terminal block Eva pan pipe s ass’y Absorbent rubber clm Absorbent rubber b TINS-A684CBRZ TLAB-A876CBRZ SPAKCA166CBZZ CPADBA799YDKZ CPADBA057CBKZ SPADBA190CBFZ SPADBA191CBFZ SPADBC435YDEZ SPADBC436YDEZ TLAB-B273CBRZ TLAB-A637CBR0 TLAB-A638CBR0 TLAB-A639CBR0 TLAB-A640CBR0 TLAB-A641CBR0 TLAB-A642CBR0 TLAB-A643CBR0 TLAB-A644CBR0 TLAB-B055CBEZ TLAB-A985CBRZ TLAB-A939CBRZ TINS-A682CBRZ Operation manual Warning label Packing case 47n Bottom pad ass’y Top pad ass’y Corner post fl Corner post fr Corner post bl Corner post br Energy label Energy label (GB) Energy label (D) Energy label (F) Energy label (E) Energy label (I) Energy label (GR) Energy label (P) Energy label (NL) R-door pocket label Two star label Caution label rof Caution sheet weee SJ-47N -WH1 1 1 1 1 1 1 1 1 1 1 1 1 AG AG AC 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 1 4 1 1 1 4 1 2 1 1 2 1 1 2 2 BW AE AG AX AD AD AF AD AM AL AH AQ AS AC AH 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AF AC BA AV AR AK AL AG AG AE AG AG AG AG AG AG AG AG AC AF AD AC CYCLE PARTS 1 2 4 5 6 9 11 18 19 21 24 25 26 28 29 MISCELLANEOUS 90909090909090909090909090909090909090909090- 1 2 3 6 7 8 9 10 11 12 13 13 13 13 13 13 13 13 15 19 21 34 HOW TO ORDER REPLACEMENT PARTS To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 3. PART NO. 2. REF. NO. 4. DESCRIPTION 32 SJ-P43N/43N SJ-P47N/47N 1 2 3 4 5 6 DOOR PARTS A SJ-P43N,P47N A SJ-43N,47N 3-6 3-6 3-5 3-5 3-5-2 3-10 3-11 B B 3-9 3-8 1-55 3-31 C 2-43 3-5-4 3-30 C 3-5-5 3-7 3-5-3 3-5-3 3-5-1 3-5-1 3-15 D D 3-15-2 3-7 3-19 3-21 5-3 5-5 E E 5-4 3-22 90-15 3-20 5-2 F F 5-2 5-35 3-17 G G 3-15-3 5-1 3-15-1 5-3 SJ-P43N SJ-43N SJ-P47N SJ-47N H 1 2 3 4 33 5 6 H SJ-P43N/43N SJ-P47N/47N 1 2 3 4 5 6 CABINET PARTS A A 5-9 5-31 B B 5-6 5-17 5-32 2-93 5-18 C C 2-29 2-13 2-93 5-19 D D 5-24 2-91 5-24-1 5-24-2 2-49 1-10 E E 2-49 4-3 2-15 5-25 5-25-1 5-25-2 F F 5-15 2-14 5-13 2-93 2-8 G G 5-16 2-7 2-93 2-7-2 2-7-1 2-8-2 2-7-1 SJ-P43N SJ-43N SJ-P47N SJ-47N H 1 2 3 4 34 5 6 H SJ-P43N/43N SJ-P47N/47N 1 2 3 4 5 6 CABINET PARTS A A 2-19 1-6 2-63 2-64 2-19 2-23 2-17 1-5 2-16 4-1 2-100 2-65 2-20 1-20 4-1 B B 2-94 2-68 2-21 2-28 2-95 2-22 2-101 1-1 1-9 1-17 2-4 2-70 C 2-44 C 2-69 2-46 4-11 (4-12) 2-2 2-66 1-21 2-72 1-4 2-24 2-79 1-3 2-67 2-99 2-39 (Only for SJ-43N,47N) 2-47 D 2-38 2-78 2-83 6-18 2-73 6-5 1-45 2-71 2-77 2-80 1-50 2-81 1-46 2-82 (Only for SJ-P43N,P47N) 2-46 D (Only for SJ-P43N,P47N) 2-45 2-27 1-22 E E 2-87 2-50 6-28 6-24 1-7 2-31 1-8 6-26 6-29 90-2 5-14 F F 2-57 6-11 6-1 2-56 2-26 4-17 6-18 6-19 2-55 1-33 1-11 6-9 6-2 6-25 4-15 6-21 6-6 G G 1-2 6-4 SJ-P43N SJ-43N SJ-P47N SJ-47N H 1 2 3 4 35 5 6 H SJ-P43N/43N SJ-P47N/47N COPYRIGHT © 2005 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. 43ATUE/ 43ATTE/ 43BTUE/ 43BTTE/ 47ATUE/ 47ATTE/ 47BTUE/ 47BTTE 36 2005 SHARP CORP. (01K0.01E) Printed in Japan