Download Magnavox 19MD311B Service manual
Transcript
19” LCD TV/DVD chassis FL11.8 SERVICE MANUAL Contents TYPE A LD190SS2 SYLVANIA (Serial No.: DS1) 19MD301B/F7 MAGNAVOX (Serial No.: DS1) LD190EM2 EMERSON (Serial No.: DS1) LD190EM2 EMERSON (Serial No.: DS2) 19MD311B/F7 MAGNAVOX (Serial No.: DS1) This service manual contains information of different types of models. Make sure to refer to the section describing your model. © 2011 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes. with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. 110426 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 How to Initialize the LCD TV/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1 Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1 Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-1 SPECIFICATIONS < LCD TV Section > < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit --- MHz ±2.3 ±2.1 TV.ch.4 CA.ch.31 CA.ch.87 dBµ dBµ dBµ 18 18 18 20 20 23 Condition Unit Nominal Limit --- kHz --- ±100 ch.4 ch.10 ch.41 dBm dBm dBm ------- -76/0 -76/0 -76/+4 Description Condition Unit Nominal Limit 1. Native Pixel Resolution Horizontal Vertical pixels pixels 1366 768 ----- --- cd/m2 230 --- Horizontal Vertical ° ° -85 to 85 -80 to 80 ----- Condition Unit Nominal Limit Horizontal Vertical % % 5 5 5±5 5±5 --x y °K 12000 0.272 0.278 --±3% ±3% Horizontal Vertical line line 400 350 ----- 1. AFT Pull-In Range 2. Synchronizing Sens. < TUNER / ATSC > Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max) < LCD PANEL > 2. Brightness (w / filter) 3. Viewing Angle < VIDEO > Description 1. Over Scan 2. Color Temperature 3. Resolution (composite video) < AUDIO > All items are measured across 8 Ω load at speaker output terminal with L.P.F. Description 1. Audio Output 10% Distortion (ATSC 0 dBfs) 2. Audio Distortion (NTSC) 3. Audio Freq. Response (NTSC) Condition Unit Nominal Limit Lch/Rch W 1.5/1.5 1.3/1.3 500mW: Lch/Rch % 0.5/0.5 2.0/2.0 -6dB: Lch -6dB: Rch Hz Hz 70 to 10 k 70 to 10 k ----- 1-1 FL11.8SP <DVD Section> < DVD > Description Condition Unit Nominal Limit 1. Horizontal Resolution (TDV-540 TIT.2 CHP.16) --- Line 350 330 2. Audio Distortion (LPCM 48 kHz, W/LPF) (PTD 1-NOR TIT.1 CHP.1) L R % 0.03 0.07 L, 20 Hz R, 20 Hz L, 20 kHz R, 20 kHz dB 0 +4/-5 L R dB 85 75 3. Audio freq. response (LPCM 48 kHz) (PTD 1-NOR TIT.1 CHP.5 -- 10) 4. Audio S/N (LPCM 48 kHz, W/LPF, A-WTD) (PTD 1-NOR TIT.1 CHP.1 -- 2) Note: Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications. 1-2 FL11.8SP LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 11.8 inches (30 cm) away from the pickup lens when the diode is turned on. Do not look directly at the laser beam. CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Drive Mechanism Assembly Laser Beam Radiation Laser Pickup Turntable Location: Top of Shield Box 2-1 TVDVDN_LBSP(1EM435619)(A1DN2UH).fm IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Safety Precautions for LCD TV Circuit d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test. 1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage. READING SHOULD NOT BE ABOVE 0.5 mA DEVICE BEING TESTED b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. LEAKAGE CURRENT TESTER _ + TEST ALL EXPOSED METAL SURFACES ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position. EARTH GROUND ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. 2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel. 3-1 LTVN_ISP 7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. 3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 3-2 LTVN_ISP Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it. I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet. L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly. 3-3 LTVN_ISP Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Chassis or Secondary Conductor Primary Circuit Table 1: Ratings for selected area AC Line Voltage Region Clearance Distance (d), (d’) 110 to 130 V U.S.A. or Canada ≥ 3.2 mm (0.126 inches) d' d Note: This table is unofficial and for reference only. Be sure to confirm the precise values. Fig. 1 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Exposed Accessible Part Z AC Voltmeter (High Impedance) Measuring Method: (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table. B Earth Ground Power Cord Plug Prongs Fig. 2 Table 2: Leakage current ratings for selected areas AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to: 110 to 130 V U.S.A. or Canada 0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible parts Note: This table is unofficial and for reference only. Be sure to confirm the precise values. 3-4 LTVN_ISP STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is indicated as shown. Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder. Top View Out Bottom View In Input 2. For other ICs, pin 1 and every fifth pin are indicated as shown. 5 Pb free mark Pin 1 How to Remove / Install Flat Pack-IC 1. Removal 10 With Hot-Air Flat Pack-IC Desoldering Machine: 3. The 1st pin of every male connector is indicated as shown. 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) Pin 1 Instructions for Connectors 1. When you connect or disconnect the FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord. 2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle. Fig. S-1-1 2. Remove the flat pack-IC with tweezers while applying the hot air. FFC Cable 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Connector 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CBA CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. * Be careful to avoid a short circuit. 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape 4-1 TVDVDN_SN With Soldering Iron: around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. Flat Pack-IC CBA Desoldering Braid Hot-air Flat Pack-IC Desoldering Machine Soldering Iron Fig. S-1-3 Masking Tape Tweezers 2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) Flat Pack-IC Fig. S-1-2 Sharp Pin Fine Tip Soldering Iron Fig. S-1-4 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) 4-2 TVDVDN_SN With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Example : 5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Pin 1 of the Flat Pack-IC is indicated by a " " mark. Hot Air Blower or Fig. S-1-7 Presolder Iron Wire Soldering Iron To Solid Mounting Point Fig. S-1-5 Flat Pack-IC CBA CBA Fig. S-1-8 Fine Tip Soldering Iron Flat Pack-IC Tweezers Fig. S-1-6 4-3 TVDVDN_SN Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. <Incorrect> CBA <Correct> Grounding Band 1MΩ CBA 1MΩ Conductive Sheet or Copper Plate 4-4 TVDVDN_SN CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Step/ Loc. No. This flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were. [1] Stand Assembly [6] Digital Main CBA Unit [2] Rear Cabinet [7] Jack CBA [3] DVD Holder [4] DVD Mechanism [5] DVD Main CBA Unit [8] Main CBA [11] Speaker [9] Stand Holder [12] Function CBA [10] LCD Module Assembly [13] Front Cabinet Removal Note [8] Main CBA 7(S-14), CN102, D4 CN201, CN872, D6 CN1001, CN1002 --- [9] Stand Holder D4 2(S-15), (S-16) --- LCD [10] Module Assembly D5 --------------- --- [11] Speaker D5 4(S-17), Speaker Holder --- Function [12] CBA 2(S-18), LED Lens*2, D5 Function Knob*2, D6 Shield Plate*2 --- D5 --------------- --- ↓ (3) ↓ (5) [13] Front Cabinet ↓ (1) ↓ (2) ↓ (4) *2: LD190EM2, 19MD311B/F7 Note: Part Fig. No. Removal (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures. Note [1] Stand Assembly D1 3(S-1) [2] Rear Cabinet D1 10(S-2), 2(S-3), (S-4) --- [3] DVD Holder D2 4(S-5), 3(S-6), CN901, D6 CN902 --- --- (2) Parts to be removed or installed. 2(S-7b)*1, [4] Fig. No. *1: Refer to the following "Reference Notes in the Table." 2. Disassembly Method Step/ Loc. No. Part (S-7a), DVD D2 CN201, CN301, Mechanism D6 CN801 [5] DVD Main CBA Unit D2 --------------D6 [6] 4(S-8), (S-9), (S-10), 4(S-11), 2(H-1), Digital Main D3 CN301, CN302, CBA Unit D6 CN303, CN3005, Shield Box, Jack Holder(D) [7] Jack CBA 4(S-12), (S-13), D3 CN702, CN871, D6 Jack Holder(A) (3) Fig. No. showing procedure of part location (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector e.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2) 1 2 3 4 5 6 (5) Refer to the following "Reference Notes in the Table." --- --- --- 5-1 FL11.8-A_DC Reference Notes 5. How to eject manually 1 1) Remove the Rear Cabinet. 1. CAUTION 1: Electrostatic breakdown of the laser diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc., during unpacking or repair work. To avoid damage of pickup follow next procedures. 2) Rotate the gear in the direction of the arrow as shown below. 1) Short-circuit the three short lands of FPC cable with solder before removing the FFC cable (CN201). If you disconnect the FFC cable (CN201) before short-circuiting the three short lands of FPC cable, the laser diode of pickup will be destroyed. (Fig. D2) 2) Disconnect the connectors (CN301 and CN801). Remove the screw (S-7a) and remove the DVD Main CBA Unit. (Fig. D2) B 2. Reassembly Notes of New DVD Mechanism: a. To remove the Chassis Cover, remove the two screws (S-7b) as shown in Fig. D2. b. To avoid damaging the pickup unit (laser diode), confirm that the three short lands (either of two places) are short-circuited by soldering as shown in Fig. D2. The gear is turned to the direction of the arrow. c. Connect the FFC cables of the new DVD Mechanism to the three connectors (CN201, CN301, CN801) on the DVD Main CBA Unit. d. After confirming that the FFC cables are securely connected to the three connectors, remove the solder from the three short lands. If the solder is not removed, the laser diode will not light and it will not be possible to read discs. e. Insert the Pin on the Chassis Cover into the Hole on the Main Chassis as shown in Fig. D2. Then tighten the two screws (S-7b) to install the Chassis Cover. View from the "B" angle 3. CAUTION 2: When reassembling, confirm the FFC cable (CN201) is connected completely. Then remove the solder from the three short lands of FPC cable. (Fig. D2) 6. How to eject manually 2 4. How to eject a disc in emergency Press and hold [EJECT] on the unit for more than 5 seconds. 1) Remove the Rear Cabinet. 2) To remove the DVD Main CBA Unit, remove the screw (S-7a) in Fig. D2. Do not disconnect connectors. 3) To remove the Chassis Cover, remove the two screws (S-7b) as shown in Fig. D2. 4) Remove a disc. 5-2 FL11.8-A_DC (S-2) (S-4) (S-2) (S-2) (S-2) [2] Rear Cabinet (S-3) (S-2) (S-1) [1] Stand Assembly Fig. D1 5-3 FL11.8-A_DC [3] DVD Holder (S-5) (S-7a) (S-5) [5] DVD Main CBA Unit (S-6) [4] DVD Mechanism A Remove the two screws (S-7b), then short-circuit the three short lands by soldering as shown in View from the "A" angle. Chassis Cover Pin (S-7b) Either of two places A FPC Cable View from the "A" angle Hole Main Chassis Fig. D2 5-4 FL11.8-A_DC [6] Digital Main CBA Unit Jack Holder(D) (S-11) (S-10) (S-8) (S-9) Shield Box (S-8) (H-1) (S-13) Jack Holder(A) (S-12) [7] Jack CBA Fig. D3 5-5 FL11.8-A_DC [8] Main CBA (S-14) (S-15) (S-14) [9] Stand Holder (S-16) (S-14) (S-14) Fig. D4 5-6 FL11.8-A_DC [LD190SS2, 19MD301B/F7] [13] Front Cabinet [12] Function CBA Speaker Holder (S-18) (S-17) Speaker Holder (S-17) [11] Speaker [LD190EM2, 19MD311B/F7] [13] Front Cabinet [11] Speaker Speaker Holder LED Lens (S-17) Shield Plate Speaker Holder (S-17) Function Knob [12] Function CBA [10] LCD Module Assembly (S-18) 5-7 Fig. D5 FL11.8-A_DC TV Cable Wiring Diagram To DVD Mechanism CN301 CN401 CN801 CN201 DVD Main CBA Unit To LCD Module Assembly CN601 To LCD Module Assembly To LCD Module Assembly Digital Main CBA Unit Main CBA CN3005 CN201 CN1001 CN301 CN3002 CN302 CN3006 CN303 CN3003 CN1002 CN902 CN901 CN702 CN701 CN102 CN872 AC Cord CN871 Jack CBA To Speaker Function CBA To Speaker CN101B Fig. D6 5-8 FL11.8-A_DC ELECTRICAL ADJUSTMENT INSTRUCTIONS How to set up the service mode: General Note: “CBA” is abbreviation for “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available. 1. Turn the power on. 2. Press [MENU] button to display Setup menu. 3. Select “Features”. 4. Select “Current Software Info”. 5. Press [0], [4], [2], [5], [7], [4] and [INFO] buttons on the remote control unit in this order. The following screen appears. Test Equipment Required 1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst) "*" differs depending on the models. Code : *******-***-*-*****-**** Pic code : **-*******-*****-** 2. Remote control unit MIPS : Push 0key 3. Color Analyzer Press "POWER" key to exit. Tuner : ****-*****-**** Safety : safety_Non 6-1 FL11.8EA 1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. Test Point Adj. Point 1. Enter the Service mode. Screen 2. Each time the [7] button on the remote control unit is pressed, the display changes as follows. [CHANNEL UP/DOWN ] buttons M. EQ. Spec. Color analyzer See below Purity Check Mode Figure White mode To avoid interference from ambient light, this adjustment should be performed in a dark room. [7] button Perpendicularity [7] button Black mode L = 1.18 inches Color Analyzer [7] button Red mode 1. Operate the unit for more than 60 minutes. 2. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. [7] button Green mode 3. Enter the Service mode. 4. Press [3] button on the remote control unit. 5. Press [CHANNEL UP/DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum. [7] button Blue mode 6. To cancel or to exit from the VCOM Adjustment, press [CH RETURN] or [PREV CH] button. [7] button White 20% mode Note: When entering this mode, the default setting is White mode. 3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button. 6-2 FL11.8EA The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA. Purpose: To mix red and blue beams correctly for pure white. 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment. [DRIVE] Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment. Symptom of Misadjustment: White becomes bluish or reddish. 6. In each color mode, press [CHANNEL UP/DOWN] buttons to adjust the values of color. Test Point Adj. Point 7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005). 3. White Balance Adjustment Screen [VOLUME DOWN] button Mode Input [VIDEO1] C/D White Raster (APL 70%) or (APL 40%) M. EQ. Spec. Pattern Generator, Color analyzer x= 0.272 ± 0.005 y= 0.278 ± 0.005 8. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button. Figure To avoid interference from ambient light, this adjustment should be performed in a dark room. Perpendicularity L = 1.18 inches Color Analyzer INPUT: WHITE 70%, 40% 1. Operate the unit for more than 60 minutes. 2. Input the White Raster(70%=70IRE, 40%=40IRE). INPUT SIGNAL 0IRE 0IRE Low Light Hight Light 100IRE 100IRE 40%=40IRE 70%=70IRE 3. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCDPanel surface. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. 4. Enter the Service mode. Press [VOLUME DOWN] button on the remote control unit and select “C/D” mode. 6-3 FL11.8EA HOW TO INITIALIZE THE LCD TV/DVD The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV/DVD using the following procedure. < DVD Section > < LCD TV Section > 1. Turn the power on. 1. Turn the power on. 2. To enter the service mode, press the service button on the service remote control unit. 2. Enter the service mode. - To cancel the service mode, press [POWER] button on the remote control unit. - To cancel the service mode, press [POWER] button on the service remote control unit. 3. Press [INFO] button on the remote control unit to initialize the LCD television. 3. To put the LCD TV/DVD into the DVD mode, press [CH RETURN] or [PREV CH] on the remote control unit. 4. “INITIALIZED” will appear in the upper right of the screen. “INITIALIZED” color will change to green from red when initializing is completed. 4. To put the LCD TV/DVD into the Flash clear mode, press [INPUT SELECT] or [SOURCE] buttons on the remote control unit within five seconds. The following screen appears. Flash Memory Clear : OK CHUCKING ON When “OK” appears on the screen, the factory default will be set. 5. To exit this mode, press[CHANNEL UP/DOWN] button to go to TV mode, or press [POWER] button to turn the power off. Note: The name of buttons may vary with the brand of unit. 7-1 FL11.11INT FIRMWARE RENEWAL MODE < DVD Section > 5. After programming is finished, the disc will be ejected automatically. Fig. c appears on the screen and the checksum will be shown in (*2). 1. Turn the power on and press [EJECT] button on the remote control unit to put the LCD TV/DVD into DVD mode. Then remove the disc. "*******" differ depending on the models. 2. To put the LCD TV/DVD into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in this order. Fig. a appears on the screen. F/W Version Up Mode (*2) VERSION : Completed SUM : **** Model No : ****** VERSION : *.** ************.*** "*******" differs depending on the models. F/W Version Up Mode Model No : ****** VERSION : *.** Please insert a DISC for F/W Version Up. Fig. c Completed Program Mode Screen At this time, no button is available. 6. Remove the disc. EXIT: SELECT 7. Unplug the AC cord from the AC outlet then plug in again. Fig. a Version Up Mode Screen 8. Press [EJECT] button on the remote control unit to put the LCD TV/DVD into DVD mode again. 3. Insert the disc for version up into the disc slot. 9. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in this order. Fig. d appears on the screen. 4. The LCD TV/DVD enters the F/W version up mode automatically. Fig. b appears on the screen. Make sure to insert the proper F/W for the state of this model. "*******" differs depending on the models. "*******" differ depending on the models. F/W Version Up Mode (*1) VERSION : Reading... MODEL : ****** Version : *.** Region : * Model No : ****** VERSION : *.** ************.*** EEPROM CLEAR : CLEAR Fig. d 10. Press [CLEAR] button on the remote control unit. Fig. e appears on the screen. Fig. b Programing Mode Screen "*******" differs depending on the models. The appearance shown in (*1) of Fig. b is described as follows: No. Appearance State 1 Reading... Sending files into the memory 2 Erasing... Erasing previous version data 3 Programming... Writing new version data EXIT: SELECT MODEL : ****** Version : *.** Region : * EEPROM CLEAR : OK EEPROM CLEAR : CLEAR EXIT: SELECT Fig. e When “OK” appears on the screen, the factory default will be set. The firmware renewal mode is now complete. 11. To exit this mode, press [CHANNEL UP/DOWN] button to go to TV mode, or press [POWER] button to turn the power off. 8-1 FL11.8FW < LCD TV Section > 4. The update will start and the following will appear on the screen. Equipment Required "*" differs depending on the models. Software Upgrade a. USB storage device b. Remote Control Unit Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Firmware Update Procedure Current Version: *******-***-*-***-**** New Version: *******-***-*-***-**** Note: There are two states (the User Upgrade and the Factory Upgrade) in firmware update. User Upgrade Factory upgrade *1 Downloading... 0% Upgrade the firmware only. The setting values are not initialized. Note: If the above screen isn’t displayed, repeat from step 1. Upgrade the firmware and initialize the setting values. The appearance shown in *1 is described as follows. Appearance The identification of User Upgrade and Factory Upgrade are done by the filename. Downloading... Downloading the firmware from the USB storage device. Writing... Writing the downloaded firmware in flash memory. Checking... Checking the new firmware. 1. Turn the power off and unplug the AC Cord. 2. Insert the USB storage device to the USB port as shown below. Rear Cabinet State USB port 5. When the firmware update is completed, the following will appear on the screen. Software Upgrade USB storage device The software upgrade is completed. Remove USB storage device, turn TV off then on again. Remove the USB storage device from the USB port. Turn the power off and turn the power on again. Note: 3. Plug the AC cord in the wall outlet and turn the power on. When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed. 8-2 FL11.8FW TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. No Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Yes Is normal state restored when once unplugged power cord is plugged again several seconds? No Yes Is the INV+31V line voltage normal? Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (D601, D602, D603, D604, Q601, Q602, T601) No Yes Check each rectifying circuit of the secondary circuit and service it if defective. FLOW CHART NO.2 The fuse blows out. Check the presence that the primary component is leaking or shorted and service it if defective. Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective. After servicing, replace the fuse. FLOW CHART NO.3 When the output voltage fluctuates. Does the photocoupler circuit on the secondary side operate normally? No Check IC601, D633, Q631 and their periphery circuit, and service it if defective. Yes Check IC601, D608, D610 and their periphery, circuit and service it if defective. FLOW CHART NO.4 When buzz sound can be heard in the vicinity of power circuit. Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (IC631, IC901, Q201, Q205, Q206, Q634, Q635, Q636, Q637, Q640, Q641, Q643, Q901, Q903, Q904, D631, D632, D636, D638, D639, D640, D641, D643) FLOW CHART NO.5 INV+31V is not output. Is approximately +31V voltage supplied to the cathode of D632? No Check C632, D632, D633 and their periphery circuit, and service it if defective. Yes Check D667, R655 and their periphery circuit, and service it if defective. 9-1 FL11.8TR FLOW CHART NO.6 PANEL+24.5V is not output. Is approximately +30V voltage supplied to the collector of Q205? No See FLOW CHART No.5 <INV+31V is not output.> Yes Check Q202, Q203, D203, P-ON-H1 line and their periphery circuit, and service it if defective. FLOW CHART NO.7 PANEL+13V is not output. Is approximately +15V voltage supplied to the collector of Q201? No Check C631, D631, D668 and their periphery circuit, and service it if defective. Yes Is approximately +13V voltage supplied to the base of Q201? No Check Q202, Q203, D201, D202, D210 and their periphery circuit, and service it if defective. Yes Replace Q201. FLOW CHART NO.8 P-ON+7V is not output. Is approximately +7V voltage supplied to the cathode of D641? No Check C641, D641 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.9 P-ON+5V is not output. (PANEL+13V is outputted normally.) Is approximately +6.8V voltage supplied to the collector of Q635? No See FLOW CHART No.8 <P-ON+7V is not output.> Yes Is approximately +6V voltage supplied to the base of Q635 and the base of Q636? No Check D659 and their periphery circuit, and service it if defective. Yes Replace Q635 and Q636. 9-2 FL11.8TR FLOW CHART NO.10 TUNER+5V is not output. (PANEL+13V is outputted normally.) Is approximately +6.7V voltage supplied to the collector of Q637? No See FLOW CHART No.8 <P-ON+7V is not output.> Yes Is approximately +6V voltage supplied to the base of Q637? No Check D659 and their periphery circuit, and service it if defective. Yes Replace Q637. FLOW CHART NO.11 P-ON+3V is not output. Is approximately +3V voltage supplied to the cathode of D638? No Check C638, D638 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.12 P-ON+3.3V(PANEL+3.3V) is not output. Is approximately +5V voltage supplied to the cathode of D639? No Check C639, D639 and their periphery circuit, and service it if defective. Yes Is the "H" signal (approximately +3.5V) inputted to the base of Q640? No Check Q638, Q639, P-ON-H2 line and their periphery circuit, and service it if defective. Yes Replace Q640. FLOW CHART NO.13 EV+3.3V is not output. Is approximately +4.6V voltage supplied to the collector of Q903? No Check C638, D638 and their periphery circuit, and service it if defective. Yes Check Q903, D905 and their periphery circuit, and service it if defective. 9-3 FL11.8TR FLOW CHART NO.14 DVD-ON+3.3V is not output. Is approximately +5V voltage supplied to the collector of Q904? No Check C638, D638 and their periphery circuit, and service it if defective. Yes Check Q904, D906, and their periphery circuit, and service it if defective. FLOW CHART NO.15 EV+9V is not output. (PANEL+13V is outputted normally.) Is approximately +13V voltage supplied to the collector of Q905? No Check C643, D643, D644 and their periphery circuit, and service it if defective. Yes Check Q905, D901 and their periphery circuit, and service it if defective. FLOW CHART NO.16 EV+1.2V is not output. Is approximately +5V voltage supplied to the emitter of Q901? No Check C640, D640 and their periphery circuit, and service it if defective. Yes Is approximately +4V voltage supplied to Pin(3) of IC901? No Check Q901, Q902, DVD-MAIN PWR line and their periphery circuit, and service it if defective. Yes Replace IC901. FLOW CHART NO.17 P-ON+9V is not output. (PANEL+13V is outputted normally.) Is approximately +13V voltage supplied to the collector of Q641? No Check C643, D643, D644 and their periphery circuit, and service it if defective. Yes Is approximately +10V voltage supplied to the base of Q641? No Check D666 and their periphery circuit, and service it if defective. Yes Replace Q641. 9-4 FL11.8TR FLOW CHART NO.18 AL+3.3V is not output. Is approximately +34V voltage supplied to the collector of Q634? No See FLOW CHART No.5 <INV+31V is not output.> Yes Is approximately +5V voltage supplied to Pin(1) of IC631? No Check Q634, D650 and their periphery circuit, and service it if defective. Yes Replace IC631. FLOW CHART NO.19 LCD-7.1V is not output. Is approximately -9V voltage supplied to the Anode of D636? No Check C636, D636, D637 and their periphery circuit, and service it if defective. Yes Is approximately -8V voltage supplied to the base of Q206? No Check Q202, Q203, D204, P-ON-H1 line and their periphery circuit, and service it if defective. Yes Replace Q206. 9-5 FL11.8TR [ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Are the contact point and installation state of the key switches (SW104~SW109, SW951~SW953) normal? No Re-install the switches (SW104~SW109, SW951~SW953) correctly or replace the poor switch. Yes When pressing each switches (SW104~SW109, SW951~SW953) do the voltage of Pin(29) of CN302 and Pin(2) of CN303 decrease? No Check the switches (SW104~SW109, SW951~SW953) and their periphery, and service it if defective. Yes Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. Operation is possible from the unit. Is 3.3V voltage supplied to Pin(2) terminal of the remote control receiver (RS101)? No Check AL+3.3V line and service it if defective. Yes No Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS101) when the infrared remote control is activated? Replace the remote control receiver(RS101) or the remote control unit. Yes Is the "L" pulse supplied to Pin(25) of CN301? No Yes Check the line between Pin(1) terminal of remote control receiver(RS101) and Pin(25) of CN301, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.3 Picture does not appear normally.(Video input) Are the video signal inputted to Pin(4) of CN302? No Yes Check the line between Pin(4) of CN302 and JK752, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. 9-6 FL11.8TR FLOW CHART NO.4 Picture does not appear normally.(Tuner input) Are the DIF signal inputted to Pin(26,28) of CN302? No Yes Check the line between Pin(26, 28) of CN302 and Pin(10, 11) of TU302, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Are the video signal outputted to Pin(6, 8) of CN302? No Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y Check the line between Pin(6, 8) of CN302 and JK751, and service it if defective. Yes Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Are the video signal inputted to Pin(15, 17, 19) of CN302? No Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr Check the line between Pin(15, 17, 19) of CN302 and input terminals(JK731, JK732, JK733), and service it if defective. Yes Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.7 Picture does not appear normally.(DVD PB) Are the video signal inputted to Pin(1, 3, 5) of CN902? No Replace DVD Main CBA Unit. Pin(9) : DVD-Y Pin(11) : DVD-Pb Pin(13) : DVD-Pr Yes Replace Digital Main CBA Unit or LCD Module Assembly. 9-7 FL11.8TR [ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Are the audio(L/R) signals inputted to Pin(2, 15) of IC771? No Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Yes No Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Are the audio(L/R) signals inputted to Pin(4, 11) of IC771? No Check the line between Pin(4, 11) of IC771 and input terminal(JK741, JK742), and service it if defective. Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. 9-8 FL11.8TR FLOW CHART NO.3 Audio is not outputted normally.(Tuner input) Are the DIF signals outputted to Pin(26, 28) of CN302? No Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Check TU302 and their periphery circuit, and service it if defective. Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.4 Audio is not outputted normally.(HDMI Audio input) Are the audio(L/R) signals inputted to Pin(5, 14) of IC771? No Check the line between Pin(5, 14) of IC771 and input terminal(JK721, JK722), and service it if defective. Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. 9-9 FL11.8TR FLOW CHART NO.5 Audio is not outputted normally.(PC Audio input) Are the audio(L/R) signals inputted to Pin(1, 12) of IC771? No Check the line between Pin(1, 12) of IC771 and input terminal(JK711), and service it if defective. Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. 9-10 FL11.8TR 10-1 X3101 25MHz OSC 6 5 2 1 3 DIGITAL MAIN CBA UNIT SCK SI SO CS WP IC3006 (MEMORY) TO AUDIO BLOCK DIAGRAM C7-SPD-EN DVD-SPD-EN INPUT0 INPUT1 AUDIO-MUTE SCK SIN SOUT CS WP H21 G22 H22 AB21 W20 W17 T19 U20 U21 N21 M19 M3 U19 DVD-REMOTE W18 LED-CONT L21 DVD-P-ON V20 Q3033 BUFFER AL+3.3V SCL K3 SDA K2 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ C7-SPD-EN DVD-SPD-EN INPUT0 INPUT1 AUDIO-MUTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN T22 XIN25 DVD-DISC-OUT T21 XOUT25 DVD-AUDIO-MUTE DVD-MAIN-PWR V19 Y21 AA22 Y20 AA21 Y17 W22 K1 L4 L19 Q3006 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ 16 6 7 8 13 11 9 15 25 5 CN3003 LED-CONT DVD-P-ON DVD-REMOTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT DVD-AUDIO-MUTE DVD-MAIN-PWR 22 SCL 21 SDA CN3006 11 15 5 29 26 28 CN3002 Q3005 CN303 16 6 7 8 13 11 9 15 25 5 CN302 22 21 CN301 11 15 5 29 26 28 REMOTE LED1 P-ON-H2 P-ON-H1 REMOTE LED1 P-ON-H2 P-ON-H1 CN301 25 27 1 9 CN3002 25 27 1 9 KEY-IN2 G20 KEY-IN1 G21 K21 K19 K20 Y22 CN302 29 CN3006 29 KEY-IN1 DVD-LED L20 CN303 2 3 CN3003 2 KEY-IN2 3 DVD-LED IC3005 (MAIN MICRO CONTROLLER) DRIVE IC201,Q207, Q208,Q209 * TU302 MAIN CBA 9 SCL 8 SDA * TU301 4 SCL 5 SDA (TUNER UNIT) (TUNER UNIT) LED-CONT DVD-P-ON DVD-REMOTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT FUNCTION CBA KEY SWITCH KEY SWITCH D950 DVD D104 POWER AL+3.3V D103 STANDBY LED-CONT DVD-P-ON DVD-REMOTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DVD SYSTEM CONTROL / SERVO BLOCK DIAGRAM DVD MAIN CBA UNIT TO INVERTER BLOCK DIAGRAM TO POWER SUPPLY BLOCK DIAGRAM REMOTE P-ON-H1 LED1 KEY-IN1 KEY-IN2 DVD-LED CN101B 2 5 4 6 7 8 CN601 DVD-AUDIO-MUTE 4 DVD-AUDIO-MUTE 13 CN902 2 26 25 24 21 22 23 3 CN901 CN401 2 26 25 24 21 22 23 3 BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3 DVD-MAIN-PWR P-ON-H2 P-ON-H1 PROTECT1 PROTECT2 VCOM Either TU301 or TU302 is used for Main CBA. Q171 Q172 CN102 2 5 4 6 7 8 REMOTE SENSOR RS101 1. System Control Block Diagram BLOCK DIAGRAMS FL11.8BLS C 10-2 JACK CBA Y CN701 27 28 26 19 20 18 16 DIF-OUT1 12 DIF-OUT2 13 IF-AGC 14 (TUNER UNIT) * TU301 DIF-OUT1 11 DIF-OUT2 10 IF-AGC 9 (TUNER UNIT) * TU302 CN702 VIDEO-IN 27 S-VIDEO-C-IN 28 S-VIDEO-Y-IN 26 S-VIDEO-SW 19 COM-VIDEO-Y-IN 20 COM-VIDEO-Pb-IN 18 COM-VIDEO-Pr-IN 16 MAIN CBA Either TU301 or TU302 is used for Main CBA. JK731 COMPONENT -Y-IN JK732 COMPONENT -Pb-IN JK733 COMPONENT -Pr-IN JK751 S-VIDEO -IN JK752 VIDEO-IN WF4 WF2 WF9 WF5 WF3 WF8 WF10 WF6 WF1 JK3001 PC-RGB IN 13 DVD-Pr 11 DVD-Pb 9 DVD-Y CN902 CN302 26 DIF-OUT1 28 DIF-OUT2 24 IF-AGC CN3006 4 6 8 5 15 17 19 CN601 4 6 8 CN3006 26 28 24 CN3003 22 20 18 14 13 3 2 1 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN 22 DVD-Y 20 DVD-Pb 18 DVD-Pr CN303 CN302 4 6 8 5 15 17 19 BUFFER IC3014 IC3013 BUFFER DVD MAIN CBA UNIT DVD-Pr DVD-Pb DVD-Y DIF-OUT1 DIF-OUT2 IF-AGC DVD-Y DVD-Pb DVD-Pr VGA-VSYNC VGA-HSYNC VGA-B-IN VGA-G-IN VGA-R-IN VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DIGITAL MAIN CBA UNIT AUDIO SIGNAL TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM VIDEO SIGNAL 2. Video Block Diagram FL11.8BLV 10-3 CN872 1 2 SP(L) GND SP(R) GND SP861 SPEAKER L-CH SP862 SPEAKER R-CH BUFFER Q841 Q771 CN701 13 15 24 22 23 AUDIO(L) AUDIO(R) INPUT1 INPUT0 SPDIF MAIN CBA 8 9 DRIVE 6 MUTE CONTROL 1 DRIVE 4 IC801 (AUDIO AMP) Q773 BUFFER Q722 Q774 BUFFER CN701 CN702 3,4 HEADPHONE(R) 3,4 9,10 HEADPHONE(L) 9,10 1,2 SP(R) 1,2 9 10 CONTROL LOGIC 13 3 IC771 (AUDIO SELECTOR) 15 11 12 14 2 4 1 5 CN871 1 2 JK851 HEADPHONE JACK JK841 DIGITAL AUDIO-OUT (COAXIAL) JK721 HDMIAUDIO(L)-IN JK722 HDMIAUDIO(R)-IN JK711 PC-AUDIO-IN JK741 COMPONENTAUDIO(L)-IN JK742 COMPONENTAUDIO(R)-IN JK753 AUDIO(L) -IN JK754 AUDIO(R) -IN JACK CBA 3 5 BUFFER Q906 WF12 3 1 Q801 5 7 IC803 (OP AMP) CN702 13 15 24 22 23 Q907 BUFFER 1 7 IC902 (OP AMP) CN902 CN601 5 DVD-AUDIO(L) 12 3 DVD-AUDIO(R) 14 1 DVD-SPDIF 16 WF7 CN303 28 DVD-SPDIF CN3003 28 CN3006 2 20 CN302 2 SPDIF 20 AUDIO-MUTE CN3006 13 11 10 12 CN3002 8 6 AUDIO(L) AUDIO(R) INPUT1 INPUT0 CN301 8 AMP(R)-OUT 6 AMP(L)-OUT CN302 13 11 10 12 CN303 CN3003 24 DVD-AUDIO(L) 24 26 DVD-AUDIO(R) 26 WF13 WF11 4 4 2 2 6 2 C7-SPD-EN DVD-SPD-EN C7-SPDIF AMP(L)-OUT AMP(R)-OUT DIGITAL MAIN CBA UNIT 1 IC3017 (BUFFER GATE) 1 IC3016 (BUFFER GATE) 7 1 IC3015 (OP AMP) INPUT1 INPUT0 AUDIO-MUTE DVD-AUDIO(L) DVD-AUDIO(R) AUDIO(L) AUDIO(R) DVD-AUDIO(L) DVD-AUDIO(R) DVD-SPDIF DVD MAIN CBA UNIT TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO SIGNAL 3. Audio Block Diagram FL11.8BLA 10-4 JK3004 HDMI-IN2 JK3003 HDMI-IN1 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL TMDS-D0(+) 7 TMDS-D0(-) 9 TMDS-D1(+) 4 TMDS-D1(-) 6 TMDS-D2(+) 1 TMDS-D2(-) 3 TMDS-CLOCK(+) 10 TMDS-CLOCK(-) 12 SDA 16 SCL 15 7 9 4 6 1 3 10 12 16 15 Q3018 Q3020 TO AUDIO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM BUFFER Q3016 BUFFER Q3015 C7-SPDIF BUFFER BUFFER DVD-AUDIO(L) DVD-AUDIO(R) AUDIO(L) AUDIO(R) AMP(L)-OUT AMP(R)-OUT IF-AGC S-VIDEO-SW DIF-OUT1 DIF-OUT2 VGA-HSYNC VGA-VSYNC VGA-R-IN VGA-G-IN VGA-B-IN VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DVD-Y DVD-Pb DVD-Pr DIGITAL MAIN CBA UNIT SW A19 B19 A18 B18 A17 B17 A20 B20 C17 D17 E19 E20 D21 D22 C21 C22 F19 F20 D16 D15 L2 C1 A2 C4 B5 G1 G2 HDMI I/F J1 IF-AGC AB22 S-VIDEO-SW F2 F1 B14 HSIN B15 VSIN D9 C11 C8 A12 B7 A8 A11 B12 D8 C12 A7 B8 VIDEO DECODER AUDIO DECODER AUDIO I/F DEMODULATOR /MPEG DECODER A/D CONVERTER IC3005 (DIGITAL SIGNAL PROCESS) DIGITAL SIGNAL PROCESS LVDS TX TP POL CPV OE STV B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, H1,H3,H7,H9 M2,M3,M7,M8, SD-A(0-12) N2,N3,N7,N8, P2,P3,P7,P8,R2 W5,W7,AA4-AA8, AB3-AB8 SD-DQ(0-15) IC3002 (DDR2 SDRAM) CN3005 23 22 21 20 19 18 13 12 11 10 9 8 16 15 6 5 4 3 1 AUDIO SIGNAL N4,P2,P4,R1-R4,T2, T4,U4,V1,V4,W1-W3 AA17 AB17 AA16 AB16 AA15 AB15 AA13 AB13 AA12 AB12 AA11 AB11 AA14 AB14 AB19 Y19 AA18 AB20 AA19 VIDEO SIGNAL LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) LLVCLK(+) LLVCLK(-) TP POL CPV OE1 STV LCD MODULE ASSEMBLY 4. Digital Signal Process Block Diagram FL11.8BLD TO SYSTEM CONTROL BLOCK DIAGRAM PANEL+15V INV+31V 10-5 MAIN CBA PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ Q1003 Q1023, Q1024 SW Q1002,Q1011 SW+16V Q1019 2 1 15 16 3 4 DTC 14 V-REF 8 11 6 5 2 3 7 1 IC1002 (COMPARATOR) 5 6 OSC PWM CONTROL LOGIC IC1001(PWM CONTROL) 12 VCC Q1014 DRIVE Q1001, Q1007, Q1016 DRIVE Q1010, Q1017, Q1018 Q1004,Q1006, Q1008,Q1012 SW+16V CURRENT CONTROL SWITCH Q1005 1 3 6 5 8 7 OVER VOLTAGE PROTECTOR Q1015 OVER VOLTAGE PROTECTOR Q1009 T1002 2 4 CN1002 1 2 CN1001 1 2 LCD MODULE ASSEMBLY BACK LIGHT BACK LIGHT 5. Inverter Block Diagram FL11.8BLINV AC601 AC CORD LINE FILTER L601 10-6 BRIDGE RECTIFIER D601- D604 MAIN CBA Q602 SWITCHING CONTROL Q601 SWITCHING 4A/125V F601 4A/125V HOT CIRCUIT. BE CAREFUL. FEED BACK Q631 COLD 2 3 HOT 1 12 13 14 16 9 10 15 11 4 IC601 6 7 4 3 2 T601 CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Q634 +5V REG. 4A/125V Q633 Q904,D906 SW+3.3V Q201,D202 SW+13V Q903,D905 SW+3.3V Q202,Q203 SWITCHING Q205 SW+24.5V 3 IC631 +3.3V REG. 2 Q637 SW+5V Q638,Q639 SWITCHING Q901,Q902 SWITCHING Q635,Q636 SW+5V Q640,D662 SW+3.3V IC901 +1.2V REG. Q641 SW+9V Q905 SW+9V Q402 Q206 SW-7.1V CN901 1 9 6~8 10 11,12 4,5 CN301 10 16 21,22 19,20 14 CN201 8 2,3 4 6,7 10 DVD-MAIN-PWR P-ON-H1 P-ON-H2 PROTECT1 PROTECT2 VCOM DVD MAIN CBA UNIT DIGITAL MAIN CBA UNIT CN3002 10 16 21,22 19,20 13,14 CN401 AL+3.3V 1 9 DVD-ON+3.3V EV+3.3V 6~8 DVD-ON+5V 10 11,12 EV+9V 4,5 EV+1.2V P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V TO SYSTEM CONTROL BLOCK DIAGRAM PANEL+15V P-ON+3.3V P-ON+9V INV+31V P-ON+5V SP+14V TUNER+5V AL+3.3V AL+3.3V DVD-ON+3.3V EV+3.3V DVD-ON+5V EV+9V EV+1.2V P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V LCD MODULE ASSEMBLY NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. PANEL-7.1V PANEL+13V PANEL+24.5V PANEL+3.3V VCOM CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 6. Power Supply Block Diagram FL11.8BLP 10-7 DISC-IN CN301 SP(+) 1 SP(-) 2 LOAD-DISC 6 GND 3 SL(-) 4 SL(+) 5 TS(+) TS(-) FS(+) FS(-) CN5001 CN801 1 LED-POWER 1 2 DVD-DISC-OUT 2 3 DVD-DISC-IN 3 DISC-OUT SENSOR CBA M SLED MOTOR M SPINDLE MOTOR LOAD-DISC DRIVE CBA TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM Q804 +3.3V 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. - 17 18 12 11 SLED MOTOR DRIVE + SPINDLE MOTOR DRIVE - + - + - + TRACKING ACTUATOR DRIVE FOCUS ACTUATOR DRIVE - + - + - 23 6 4 5 3 1 2 25 24 27 26 VREF RESET 3 IC462 + 1 +3.3V 14 13 15 16 RESET 1 IC461 IC301 (SERVO DRIVE) 2 +3.3V 5 6 3 2 IC202 (OP AMP) 7 1 61 DVD-DISC-OUT 63 DVD-DISC-IN DVD-SCLK DVD-CS DVD-SDATA DVD-REMOTE DVD-P-ON 65 LOAD-DISC 121 SP-ROT 122 SL-ADS 67 SLD 66 SPDL 123 TD-OFST 126 TRACKING DRIVE 127 FOCUS DRIVE 124 FD-OFST 70 RESET 53 54 56 49 77 IC101 (MICRO CONTROLLER) DVD-SCLK DVD-CS DVD-SDATA DVD-REMOTE DVD-P-ON LED-CONT DVD-DISC-OUT DVD-DISC-IN TO SYSTEM CONTROL BLOCK DIAGRAM DVD MAIN CBA UNIT 7. DVD System Control / Servo Block Diagram FL11.8BLSD FS PICKUP TS DETECTOR FS(+) FS(-) TS(+) TS(-) CD-LD DVD-LD PD-MONI GND(DVD-PD) GND(CD-PD) GND(LD) C D A B CD/DVD ~ ~ 13 42 53 ~ CN201 2 3 1 4 CD 4 1 3 6 FS(+) FS(-) TS(+) TS(-) IC201 (SW) DVD Q253,Q254 CN201 10 AMP 8 AMP Q251,Q252 7 6 5 9 159 DATA RAM INST. ROM INTERRUPT CONTROLLER RF SIGNAL PROCESS CIRCUIT SDRAM DATA(0-15) 62 CD/DVD 106 104 105 103 99 100 98 97 115 116 113 114 178 TO DVD SYSTEM CONTROL / SERVO BLOCK DIAGRAM SDRAM DATA(0-15) CN201 16 18 17 15 19 ~ ~ ~ SDRAM TIMER ECC CPU I/F BCU DMA DECODER I/F STREAM I/F CPU I/F DVD MAIN CBA UNIT BCU DEBUG 21~30 34~42 212 READ MEMORY UMAC 1~4 7~14 17~18 215 216 WATCH DOG TIMER 32BIT CPU DVD/CD FORMATTER IC101 (MICRO CONTROLLER) 22 194 26 SDRAM ADDRESS(0-10) SDRAM ADDRESS(0-10) 29 209 34 EXTERNAL MEMORY I/F 2 INST CACHE VIDEO I/F AUDIO I/F INST. ROM DATA RAM INST. ROM DATA RAM DATA CACHE 32BIT CPU REMOTE CONTROL WATCH DOG TIMER TIMER INTERRUPT CONTROLLER GENERAL I/O SERIAL I/O PROCESSOR DSP DECODER NTSC/PAL ENCODER AUDIO D/A CONVERTER Pr Pb Y 129 130 131 FDQ (0-15) FADR (0-19) D/A D/A D/A 151 146 144 152 1 9 16 25 48 29 36 38 45 TO VIDEO BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO AUDIO BLOCK DIAGRAM AUDIO SIGNAL FLASH ROM IC103 (FLASH ROM) DVD-Pr DVD-Pb DVD-Y DVDAUDIO-MUTE DVD-AUDIO(R) DVD-AUDIO(L) DVD-SPDIF ~ ~ ~ 10-8 ~ IC503 (SDRAM) VIDEO SIGNAL 8. DVD Digital Signal Process Block Diagram FL11.8BLDD SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards. Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in µF (P = 10-6 µF). 5. All voltages are DC voltages unless otherwise specified. 6. This schematic diagrams are masterized version that should cover the entire FL11.8 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the FL11.8 chassis. Please refer to the parts lists for each models. 7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version. 11-1 FL11.8SC LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 3. Note: 1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.: Unit: Volts Unit: Volts 1 2 5.0 The same voltage for both TV & DVD modes 3 5.0 <0> TV mode DVD mode Indicates that the voltage is not consistent here. 5. How to read converged lines 1-D3 Distinction Area Line Number (1 to 3 digits) 3 AREA D3 2 Examples: 1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 1 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1". 1-B1 AREA B1 1-D3 A B C D 6. Test Point Information : Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin. The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function. 11-2 FL11.8SC Main 1 Schematic Diagram MAIN CBA 4 R1117 WIRE JS1010 OPEN JS1011 R1118 1.2 Q1020 OPEN R1034 OPEN R1033 OPEN Q1011 2SA950-Y (SW+16V) 15.9 16.9 31.431.531.431.4 8 7 6 5 R1099 15.2 1K C1020 0.1 C1023 10/50V C1052 0.1 R1031 4.7K D1019 OPEN D1031 Q1002 OPEN KTC3199-GR-AT/P SWITCHING BACKLIGHT-ON 0.1 R1004 10K R1001 2.2K C1034 0.01 0.7 R1005 24K R1067 1K R1065 2.7K 3 R1066 2.7K C1035 0.01 15.1 C1011 1000 /35V C1018 0.1 0 D1016 1SS133 0.8 R1039 68K 0 Q1008 KTC3199-GR-AT/P SWITCHING BACKLIGHT-ON R1100 WIRE R1049 0.8 12K 0.1 Q1012 KTC3199 R1042 0 -GR-AT/P 22K SWITCHING BACKLIGHT-ON 0.1 0.7 Q1004 KTC3199 R1048 0 -GR-AT/P 22K JS1004 SWITCHING OPEN BACKLIGHT-ON JS1005 2 R1035 1K R1021 OPEN R1105 3.3K D1033 OPEN R1013 12K D1007 1SS133 D1012 1SS133 8 4 7 1 6 D1013 C1001 D1010 2200P 1SS133 1SS133 D1009 1SS133 3 5 C1008 10P/6KV R1032 0.33/2W C1054 0.1 R1103 OPEN C1024 0.01 R1036 15K R1040 6.2K R1052 D1045 100K 1SS133 R1043 5.1K C1036 OPEN 0.3 0.3 5.2 5.2 15.93.3 0 0 16 15 14 13 12 11 10 9 V-REF CTL VCC DRIVE PWM CONTROL LOGIC DRIVE OSC DTC GND 1 2 3 4 5 6 7 8 1.5 2.6 0.7 1.3 1.6 3.8 0 3.3 C1031 2700P /100V R1053 OPEN JS1007 R1109 2.2K R1046 C1028 24K 0.01 R1112 0 C1021 OPEN R1064 33K R1061 33K C1012 220P /500V D1023 1SS133 C1042 0.22 R1083 1M IC1002 KIA358F-EL (OP AMP) D1040 OPEN BACK LIGHT D1001 1SS133 LCD MODULE ASSEMBLY R1014 27K D1004 1SS133 0 0 R1062 R1051 R1050 390K 390K 390K R1029 1.8K R1090 47K R1086 100K C1015 10P /6KV CN1001 2 1 C1039 0.01 D1024 1SS133 R1011 D1030 16BSB-T26 12K R1104 OPEN D1037 1SS133 D1022 1SS133 1 2 3 4 0.2 3.6 0.2 3.6 R1087 68K 3.8 15.80 1.7 1.1 8 7 6 5 VCC D1020 5V1BSB-T26 C1043 R1089 0.22 12K GND 1 2 3 4 0.2 1.7 1.1 3.6 D1025 1SS133 R1088 1M C1041 0.01 R1059 10k 0.2 Q1014 KTC3199-GR-AT/P (SWITCHING) R1045 240K D1041 OPEN C1033 10/50V Q1015 KTC3199-GR-AT/P OVER VOLTAGE PROTECTOR 0.7 C1032 R1060 0.01 10K C1002 0.022 /100V R1082 68K 0 Q1019 KTC3199-GR-AT/P OVER VOLTAGE PROTECTOR 3.3 0 R1084 C1040 0 100K 1000P Q1009 R1012 KTC3199-GR-AT/P 27K OVER VOLTAGE PROTECTOR 0.1 0.7 0 R1023 10K C1003 0.01 C1009 10/50V R1009 1K 3.3 D1011 1SS133 D1006 R1022 1SS133 33K R1094 12K BACK LIGHT R1056 R1057 R1055 R1054 100k OPEN 100K 5.6K 0 D1038 WIRE R1019 390 C1055 OPEN 31.431.431.431.4 8 7 6 5 C1053 100/25V C1013 OPEN C1010 10/50V R1020 D1034 1K 9V1BSB-T26 R1081 100K R1047 OPEN Q1003 KTC3199-GR-AT/P OVER VOLTAGE PROTECTOR 0.4 C1004 R1016 0.01 OPEN R1015 D1005 10K 6V2BSB-T26 D1027 D1036 1SS133 1SS133 R1018 390 D1026 1SS133 2 R1010 10 R1044 5.1K C1045 0.1 D1028 4V7BSB-T26 R1037 C1025 0 0.01 C1016 6800P R1095 1.2K R1030 12K C1026 0.1 Q1022 OPEN CURRENT CONTROL SWITCH IC1001 TL494CDR PWM CONTROL C1027 10/50V R1108 WIRE R1091 12K C1059 D1003 OPEN 1SS133 D1008 1SS133 D1002 1SS133 R1038 240K R1041 1K R1110 Q1023 10K KTC3199 -GR-AT/P (SWITCHING) 3.7 0.2 0 R1106 10K R1092 12K T1002 INVERTER TRANS D1015 1SS133 CN1002 2 1 C1014 10P /6KV R1111 10K D1035 OPEN D1014 1SS133 R1024 22K R1107 10K 5.2 Q1024 KTA1267 4.9 -GR-AT/P (SWITCHING) 1.9 C1058 OPEN 1 2 3 4 Q1017 KTC3199-GR-AT/P 0.2 3.5 0.2 3.5 (DRIVE) R1101 OPEN JS1013 OPEN 15.6 3.5 R1102 D1039 C1017 R1002 R1006 180 OPEN OPEN 3.7 C1047 OPEN 180 R1007 OPEN 10 3.5 3.7 Q1001 Q1018 R1008 D1029 KTA1267-GR-AT/P 12K KTC3199 16BSB-T26 0 (DRIVE) -GR-AT/P (DRIVE) JS1012 15.6 3.6 C1048 3.7 OPEN 3.6 3.7 Q1007 KTA1267-GR-AT/P 0 (DRIVE) C1050 C1005 R1017 R1093 OPEN 12K 0.022 12K /100V D1018 10BSB-T26 R1028 1K R1027 5.1K C1038 D1021 0.1 15BSB-T26 R1026 2.2K Q1010 KTC3199 -GR-AT/P (SWITCHING) 3.7 Q1016 0.3 KTC3199 0 -GR-AT/P (SWITCHING) R1069 1K R1025 1.5K R1070 1K CONTINUE MAIN 4 INV+31V PANEL+15V CONTINUE MAIN 4 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ C1049 OPEN 3.7 0.4 R1068 1K 0 0 Q1006 KTA1267-GR-AT/P (SW+16V) 15.8 15.9 R1074 100K R1003 2.2K C1007 2200P C1019 220P /500V Q1005 TPC8214-H CURRENT CONTROL SWITCH R1096 OPEN R1097 OPEN C1006 10P/6KV R1058 10K C1044 0.1 C1056 0.1 R1113 OPEN JS1006 OPEN R1114 OPEN Q1025 OPEN (SWITCHING) 1 R1115 OPEN R1116 OPEN C1057 OPEN R1071 R1072 4.3K 0 R1073 1.2K A B C1037 1 C D 11-3 E F FL11.8SCM1 Main 2 Schematic Diagram *Either TU301 or TU302 is used for MAIN CBA. 4 CONTINUE MAIN 4 TU-VT+31V TUNER+5V P-ON+9V DVD-M+10V(EV+9V DVD+5V AL+3.3V P-ON+5V 3 2 5 6 7 8 JS304 2 3 4 5 6 7 8 JS306 D904 OPEN 5.3 R918 10K 5.2 4.5 R914 2.7 /1/2W C305 0.1 C301 0.1 0.8 R916 10K R925 5.6 4.6 R924 5.6 4.0 R922 22 C306 22/50V C302 0.1 D303 5V6BSB-T26 C303 330/10V C311 47P L303 LK1608R22KT C310 47P L302 LK1608R22KT R305 82 5.2 R928 180 4.1 R927 10 VIN R912 1K R913 3.9 /1/2W C916 1000/6.3V C913 OPEN C912 0.1 C911 0.1 R919 150 R920 3.3K C914 0.1 C917 220/6.3V D907 1SS133 R926 470 C918 100/10V C920 0.1 R909 100 D906 3V9BSB-T26 R679 10K D417 1SS133 R303 0 R302 0 D301 OPEN D302 OPEN C314 OPEN C315 OPEN D415 1SS133 WF6 WF5 WF4 WF7 R233 10K R225 0 C209 47/25V R227 100K C214 1000P R226 10K WF1 13.3 5.8 SPDIF VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN S-VIDEO-Y-IN INPUT1 AUDIO(R) INPUT0 AUDIO(L) COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN AUDIO-MUTE 6.0 Q207 2SC2655-Y (V-COM DRIVE) R228 WIRE 5.8 6.0 Q208 0 2SA1020-Y (V-COM DRIVE) R229 10K IC201 TL3472CDR (COMPARATOR) C210 OPEN C211 OPEN C212 OPEN C213 OPEN C928 100/16V R231 1.5K R238 0 13.2 6.1 5.8 5.8 8 7 6 5 VCC 1 C216 1 C217 47/25V R905 10K R230 10K R232 15K 5.2 0 GND 4 0.2 0.2 0 0 2 3 R908 2.2K C907 390P BC902 0 R237 OPEN C908 OPEN R907 2.2K 4.0 Q907 KTC3199-GR-AT/P (BUFFER) C906 4.6 390P WF2 WF3 9.2 C215 0.1 R224 1 C909 OPEN BC901 BK1608HS601-T 9.2 3.9 C929 Q906 0.1 KTC3199-GR-AT/P 4.6 (BUFFER) R940 10K R904 10K R234 1K 0.2 Q209 KTC3199-GR-AT/P (V-COM DRIVE) JS801 0 R931 100K R943 10K C925 270P C905 OPEN L901 WIRE R942 100K WF10 IC902 NJM4558M(TE1) (OP AMP) JS802 0 R941 100K C927 1000P 9.2 4.9 4.7 4.6 8 7 6 5 VCC 1 JS803 0 JS804 0 R901 OPEN R902 OPEN GND 4 4.6 4.6 4.6 0 2 3 R903 OPEN C926 1000P JS805 OPEN R935 10K KEY-IN1 KEY-IN2 DVD-LED PROTECT1 C901 OPEN WF9 C902 OPEN WF8 C903 OPEN WF11 C924 1 R936 10K C923 270P CONTINUE MAIN 3 C922 1 R933 100K CN901 3.4 1 3.3 2 3.4 3 1.3 4 1.3 5 3.4 6 3.4 7 3.4 8 3.4 9 5.2 10 9.6 11 9.6 12 0 13 0 14 0 15 0 16 0 17 0 18 0 19 2.5 2.4 3.4 2.4 2.7 0 R921 10K 3.4 Q904 KTC3199-GR-AT/P (SW+3.3V) C919 22/50V R304 82 C915 0.1 R910 0.3 1.3 3.9 D905 KIA431-AT/P R929 1.2 R911 0.3 3.4 Q903 2SC2120-Y (SW+3.3V) R923 220 CN302 29 3.4 28 0.2 0 27 26 1.7 25 0 24 0 23 3.3 22 3.3 21 3.3 20 0 19 0 18 0 17 0 16 0 15 0 14 0 13 4.0 12 0 11 4.0 10 0 9 0 8 0 7 0 6 0 5 3.3 4 0 3 0 2 1.7 1 0 3 R917 390 0.2 Q902 KTC3199-GR-AT/P 0 (SWITCHING) R915 10K C309 1000P R306 OPEN L301 BEAD 2 0 JS301 OPEN R313 0 R307 OPEN 1 Q901 2SA950-Y (SWITCHING) 9 10 11 JS305 BC301 BK1608HS601-T CONTINUE MAIN 3 1 4 VOUT NU NU NU SCL SDA +32V +5V NU IF-AGC DIF-OUT2 DIF-OUT1 1 3 GND SCL NU NU DIF-OUT1 DIF-OUT2 IF-AGC +5V NU NU NU NU 9 10 11 12 13 14 15 16 17 18 19 2 JS303 OPEN CONTINUE MAIN 4 VCOM-PWM VCOM RESET PANEL+13V IC901 AP1117TG-U/TO-220 (+1.2V REG.) TUNER UNIT 1 JS308 OPEN JS307 OPEN C304 0.1 TO DIGITAL MAIN CBA UNIT CN3006 KEY-IN1 DIF-OUT2 GND DIF-OUT1 GND IF-AGC RESET SCL SDA AUDIO-MUTE COM-VIDEO-Pr-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Y-IN GND AUDIO(L) INPUT0 AUDIO(R) INPUT1 GND S-VIDEO-Y-IN GND S-VIDEO-C-IN S-VIDEO-SW VIDEO-IN GND SPDIF GND * TU302 TUNER UNIT NU NU NU +5V NU +32V GND SDA * TU301 C904 OPEN WF12 20 21 22 23 24 25 26 TO DVD MAIN CBA UNIT CN401 AL+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON TO DIGITAL MAIN CN303 CBA UNIT CN3003 0 1 GND 3.4 2 KEY-IN2 0.6 3 DVD-LED 4 P-ON-H3(NU) 3.2 5 DVD-MAIN-PWR 0 6 DVD-P-ON 2.7 7 DVD-REMOTE 2.4 8 DVD-SDATA 3.4 9 DVD-DISC-IN 0 10 GND 2.5 11 DVD-CS 0 12 GND 2.5 13 DVD-SCLK 0 14 GND 3.4 15 DVD-DISC-OUT 3.3 16 LED-CONT 0 17 GND 0.9 18 DVD-Pr 0 19 GND 0.9 20 DVD-Pb 0 21 GND 0.6 22 DVD-Y 0 23 GND 4.0 24 DVD-AUDIO(L) 3.4 25 DVD-AUDIO-MUTE 3.8 26 DVD-AUDIO(R) 0 27 GND 1.7 28 DVD-SPDIF 0 29 GND CN902 0.9 13 0 12 0.9 11 0 10 0.6 9 0 8 0 7 0 6 1.6 5 3.4 4 1.6 3 0 2 1.7 1 TO DVD MAIN CBA UNIT CN601 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF WF13 MAIN CBA G H I J 11-4 K L FL11.8SCM2 Main 3 Schematic Diagram MAIN CBA CN862A 1 2 3 4 C801 OPEN 4 CONTINUE MAIN 4 LED1 REMOTE P-ON-H1-SW CN872 SP862 SPEAKER R-CH 1 SP(R) 2 SP-GND TO FUNCTION CBA CN101B CN102 1 2 3 4 5 6 7 8 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED CN702 JS103 OPEN CONTINUE MAIN 4 3 (NO CONNECTION) SP(R) SP(R) SP-GND SP-GND C805 330/25V JS101 WIRE C807 0.022 R804 8.2 P-ON+5V P-ON+9V P-ON+3.3V AL+3.3V SP+14V D808 20BSB-T26 R806 WIRE CONTINUE MAIN 2 C802 0.1 BC801 BK1608HS601-T KEY-IN1 KEY-IN2 DVD-LED PROTECT1 C806 330/25V R807 WIRE R815 470 R808 4.7K C812 470/25V C831 100/16V R816 470 R809 360 D804 1SS133 C811 0.1 CONTINUE MAIN 4 PROTECT1 AMP(R)-OUT AMP(L)-OUT R810 5.6K R836 100K R821 100K C827 1 R409 2.2K D414 6V2BSB-T26 R834 10K R818 15K R838 10K R819 10K R820 4.7K R837 100K C828 390P C832 0.1 IC803 NJM4558M(TE1) (OP AMP) D805 1SS133 C813 100/25V C825 1 C830 1000P 2 D413 1SS133 2.1 1 0 2 GND 7.0 3 RIPPLE FILTER 6.9 4 0 5 GND C816 1000P R817 18K 12.9 0 9.2 4.6 4.6 4.6 8 7 6 5 VCC R803 10K 0 7.0 6 14.4 7 VCC 13.0 8 R842 100K C833 0.1 D809 20BSB-T26 IC801 TDA1517P/N3 (AUDIO AMP) C809 1 R811 10K C808 0.022 R805 8.2 C838 OPEN DRIVE NU 18 0 NU 17 0 R678 10K NU 16 0 NU 15 0 NU 14 0 NU 13 0 NU 12 0 NU 11 0 MUTE CONTROL 2.1 9 DRIVE NU 10 0 C818 0.1 CONTINUE MAIN 2 SPDIF VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN S-VIDEO-Y-IN INPUT1 AUDIO(R) INPUT0 AUDIO(L) COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN AUDIO-MUTE C819 0.1 C820 OPEN C829 1000P C821 0.1 R826 10K R830 10K R823 100K C810 1 1 R813 10K M N R814 5.6K TO JACK CBA CN701 SP(R) SP(R) HEADPHONE(R) HEADPHONE(R) GND GND GND GND HEADPHONE(L) HEADPHONE(L) GND GND AUDIO(L) P-ON+9V AUDIO(R) COM-VIDEO-Pr-IN GND COM-VIDEO-Pb-IN S-VIDEO-SW COM-VIDEO-Y-IN GND INPUT0 SPDIF INPUT1 GND S-VIDEO-Y-IN VIDEO-IN S-VIDEO-C-IN GND Q801 KTC3199-GR-AT/P (AUDIO-MUTE) GND 1 2 3 4 4.6 0 4.6 0 C826 390P 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 C817 1000P O P 11-5 Q R FL11.8SCM3 Main 4 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V CONTINUE MAIN 1 INV+31V PANEL+15V CONTINUE MAIN 3 PROTECT1 AMP(R)-OUT AMP(L)-OUT MAIN CBA R930 6.8/2W T601 POWER TRANS 3 15 R401 D401 1 FR104-B 4A 125V C601 0.47 /300V R601 1M /1/2W D602 1N5397BD D612 1ZB2220 -YBB 4 R602 1.2/3W 10 D604 1N5397BD 16 6 C606 560P/2KV 13 D640 SB240-B/P D639 FR151-B/P R608 150 0 0.4 D607 39BSB-T26 R610 0.39/2W R655 470 C655 22/50V 5.2 15.4 R201 5.6/1W D668 27BSB-T26 13.9 D210 R207 6.8K R208 6.8K R609 1.5K D610 0 D644 OPEN R221 22K C644 OPEN D636 FR104-B C636 100/25V C692 2200P/250V R631 12K D637 36BSB-T26 -9.2 -8.5 31.2 24.9 R219 10 R216 2.7K R217 2.7K D203 C656 0.1 R222 120 D641 SB360BH 6.9 R203 510 R666 6.1 22K R635 220 4.0 R670 270 6.9 Q639 KTA1267-QR-AT/P (SWITCHING) C683 0.1 3.3 Q640 2SC4881F (SW+3.3V) C652 1000 /6.3V R204 2.2K D661 OPEN 0.2 24.3 Q205 KTC3199 -GR-AT/P (SW+24.5V) D205 24BSC-T26 D206 0 R665 3.9 R664 3.9 R235 OPEN C205 OPEN R218 8.2K D662 KIA431-AT/P R223 15K C684 0.1 R698 OPEN R673 3.6K R671 10 C651 OPEN C685 0.1 R674 10K R669 10K C661 3.3/50V R668 22K Q635 2SC2120-Y (SW+5V) 6.8 5.2 5.9 6.8 5.9 5.9 C648 47/25V 5.2 Q637 2SC2120-Y (SW+5V) C650 220/10V D412 5.2 Q636 2SC2120-Y (SW+5V) C649 220/10V R662 39 R661 680 D660 WIRE D411 6.7 R663 3.3 R690 3.3 C204 10/50V 0.7 Q638 KTC3199-GR-AT/P (SWITCHING) D659 KIA431B-AT/P C646 0.1 C207 10/50V D645 R699 56 R632 1.1K R633 10K R406 47K R660 10K R408 47K R407 47K C220 0.1 D207 7V5BSA-T26 3.1 -1.3 0 Q402 KTC3199 -GR-AT/P (SWITCHING) D405 C221 0.1 R637 220 R636 OPEN 2 C645 2200P /100V 4 3 30.6 6.3 Q631 5.7 KTC3199 -GR-AT/P (FEED BACK) R638 D656 2.7K D648 HZS5.6NB2TE-EQ 1 R645 7.5K R644 22K R643 22K R642 22K R639 820 R646 820 R653 820 R654 820 R681 820 D649 3V3BSB-T26 R651 15 R656 R650 680 680 D654 FR154 6.4 Q634 KTC3199 6.7 -GR-AT/P (+5V REG) R652 R649 WIRE 680 D650 6V8BSA-T26 D646 R658 2.7K D647 OPEN R641 120 R640 18K 0.2 0 COLD 0.7 Q633 KTC3199-GR-AT/P (SWITCHING) R688 1 5.8 D651 5.1 D652 OPEN R689 33 R683 3.3/1W 5.0 Q643 R684 2SA950-Y 3.3/1W (SWITCHING) D657 4V7BSB-T26 C647 100/10V IC631 LD1117V (+3.3V REG.) R682 WIRE D416 10BSB-T26 R413 22K R634 12K D403 OPEN D655 FR154 31.8 COM 1 30.6 R611 2.2K HOT C681 0.1 31.6 0.4 C607 0.082 /100V R411 22K D404 D410 C641 3300/10V IC601 LTV817MCF ERROR VOLTAGE DET 13.3 R412 22K D408 R667 1K R212 22K D204 Q206 KTC3199-GR-AT/P (SW-7.1V) -9.1 C608 1800P /100V R220 47K C206 OPEN C202 0.01 R205 1.5K C201 470/25V R202 9.1K D202 KIA431-AT/P D643 FR252 C643 1000/25V 13.3 Q201 2SD400 (SW+13V) Q203 KTC3199 -GR-AT/P (SWITCHING) 0.7 R211 10K R215 330 C691 4700P/250V 2 D201 31.7 Q202 KTA1267 -QR-AT/P (SWITCHING) R213 27K 0.1 D605 4V3BSB-T26 D609 OPEN D409 D667 OPEN R672 0.18/1W R214 31.1 3.3K R612 220 0 D653 C682 0.1 C640 1000/10V R607 150 D608 R240 3.9K D209 R206 47K D642 R677 1K D406 R210 6.8K D208 31.8 5.8 R209 56K 24.3 0.4 Q210 KTC3199 -GR-AT/P (SWITCHING) C605 1200P /100V Q602 2SC2120-Y SWITCHING CONTROL R239 150 C653 22/50V R680 OPEN D407 R176 OPEN C638 2200/6.3V C631 470/25V C604 0.039 /100V Q171 0 KTC3199 -GR-AT/P (SWITCHING) C654 100/16V C639 2200/10V D631 SB2A0BD D606 27BSB-T26 9.9 D633 1ZB43BB D638 SB240-B/P 12 9.2 Q641 KTC3199 -GR-AT/P (SW+9V) R403 36K R675 1K C632 1000/35V BC601 BEAD Q601 TK5A50D (SWITCHING) 13.8 4.7 0 Q172 0 KTC3199 -GR-AT/P (SWITCHING) R172 22K 0 0.6 R175 22K D901 10BSC-T26 D666 10BSB-T26 D665 WIRE D603 1N5397BD 7 D 134.0 G 5.8 S 0.2 R676 22 D632 30PHA20 L601 LINE FILTER R603 390K R604 390K R606 330K R605 390K R404 OPEN 0 C921 OPEN C203 0.1 C633 1500P/1KV 14 3 -3.7 Q401 KTC3199 -GR-AT/P (RESET) 9 C603 270 /200V R171 22K R932 WIRE R906 560 R173 OPEN R174 OPEN 5.9 R402 5.6K C401 1/50V D601 1N5397BD SA601 SURGE ABSORBER D402 10BSB-T26 D909 1N4005 C910 47/25V Q905 2SD400 (SW+9V) 10.3 1 R659 2.7 /1/2W R685 620 VIN F601 4A/125V 11 D902 1N4005 VOUT AC601 AC CORD 2 D903 1N4005 D908 1N4005 C402 OPEN 4 9.6 11.6 HOT CIRCUIT. BE CAREFUL. 2 3 2.1 3.4 5.1 D670 SB160 R405 OPEN R647 47K C219 0.1 R648 10K R414 OPEN C218 0.1 R686 1K TO DIGITAL MAIN CBA UNIT CN3002 P-ON-H2 GND GND GND PROTECT3 AMP(L)-OUT GND AMP(R)-OUT P-ON-H1 P-ON+3V PROTECT1 GND LED-R P-ON+5V PROTECT2 P-ON+7V GND GND P-ON+3.3V P-ON+3.3V AL+3.3V AL+3.3V GND GND REMOTE BACKLIGHT-SW LED1 BACKLIGHT-ADJ VCOM-PWM CONTINUE MAIN 1 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ CONTINUE MAIN 2 VCOM-PWM VCOM RESET PANEL+13V CONTINUE MAIN 3 LED1 REMOTE P-ON-H1-SW CONTINUE MAIN 2 TU-VT+31V TUNER+5V P-ON+9V DVD-M+10V(EV+9V DVD+5V AL+3.3V P-ON+5V CONTINUE MAIN 3 P-ON+5V P-ON+9V P-ON+3.3V AL+3.3V SP+14V TO LCD MODULE CN201 ASSEMBLY 1 GND 2 PANEL+13V 3 PANEL+13V 4 PANEL+24.5V 5 GND 6 PANEL+3.3V 7 PANEL+3.3V 8 PANEL-7.1V 9 GND 10 VCOM 11 GND CN301 3.3 1 0 2 0 3 0 4 3.3 5 2.6 6 0 7 2.6 8 3.2 9 3.4 10 2.1 11 0 12 0.6 13 5.2 14 0 15 6.9 16 0 17 0 18 3.3 19 3.3 20 3.3 21 3.3 22 0 23 0 24 3.3 25 3.2 26 0.6 27 0.9 28 0.7 29 UNLESS OTHERWISE SPECIFIED: DIODES ARE 1SS133. S T U V 11-6 W X Y FL11.8SCM4 Jack Schematic Diagram BC841 BK1608HS601-T C843 0.1 4 3.6 JK841 DIGITAL AUDIO-OUT (COAXIAL) R844 220 C841 1 C845 33P C773 1 R847 10K R846 100 9.2 4.3 Q841 KTC3199-GR-AT/P (BUFFER) C842 1 R848 10K R845 100K BC771 BEAD R843 110 R788 82K C704 1 C703 1 PC-AUDIO-IN VDD 16 9.0 15 5.1 D708 EDZTE618.2B 4.6 3 4.6 4 14 5.1 13 4.6 5.1 5 0 6 INH 0 7 VEE 12 5.1 11 4.6 JK721 3 C724 1 JK722 R728 56K R722 100K R795 100K 0 8 GND R727 56K R721 100K HDMIAUDIO(R)-IN R794 100K SW CTL R773 10K R772 10K 5.1 1 5.1 2 R793 100K C771 100/16V C772 0.1 D702 EDZTE618.2B R792 100K HDMIAUDIO(L)-IN IC771 TC4052BF(ELNF) (AUDIO SELECTOR) R791 82K R717 56K R711 100K C723 1 R790 82K R718 56K R712 100K JK711 R789 82K C744 1 JK742 R748 56K R742 100K R784 100K 10 9.2 9 9.2 R785 100K R786 100K C731 39P JK732 2 COMPONENT -Pb-IN R732 75 C732 39P JK733 COMPONENT -Pr-IN R733 75 D706 8V2BSB-T26 R774 10K 0 Q771 KTC3199-GR-AT/P (INVERTER) C751 100P 9.1 Q722 KTC3199-GR-AT/P (INVERTER) D709 8V2BSB-T26 R775 10K 0 0 9.2 1 C752 100P R752 75 C753 100P R753 75 R754 100K JK754 AUDIO(R)-IN C734 0 R735 10 C735 0 R736 10 C736 0 R756 10 C754 0 R757 10 C755 0 R758 10 JK753 AUDIO(L)-IN R734 10 R755 100K D710 EDZTE618.2B R779 OPEN R778 OPEN 9.2 4.6 Q773 KTC3199-GR-AT/P C776 4.0 (BUFFER) 33P 4.6 R777 OPEN R797 2.2K R796 2.2K C756 0 C757 1 R763 56K C758 1 R764 56K CN871 1 SP(L) 2 SP-GND D707 EDZTE618.2B JS701 0 D704 EDZTE618.2B C861 OPEN JACK CBA A C775 Q774 4.0 33P KTC3199-GR-AT/P (BUFFER) R751 75 JK752 VIDEO-IN L853 WIRE CN701 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 C733 39P JK751 S-VIDEO-IN C Y SW C852 OPEN L854 OPEN 0 D701 EDZTE618.2B JK731 R731 75 C851 OPEN R787 100K JK851 HEADPHONE JACK D705 8V2BSB-T26 R776 OPEN COMPONENT -Y-IN R783 82K R851 L851 180 WIRE R747 56K R741 100K COMPONENTAUDIO(R)-IN R782 82K D703 EDZTE618.2B C743 1 JK741 R781 82K R852 L852 180 WIRE 9.2 COMPONENTAUDIO(L)-IN R780 82K B C D 11-7 CN861A 1 2 3 4 TO MAIN CBA CN702 SP(R) SP(R) HEADPHONE(R) HEADPHONE(R) GND GND GND GND HEADPHONE(L) HEADPHONE(L) GND GND AUDIO(L) P-ON+9V AUDIO(R) COM-VIDEO-Pr-IN GND COM-VIDEO-Pb-IN S-VIDEO-SW COM-VIDEO-Y-IN GND INPUT0 SPDIF INPUT1 GND S-VIDEO-Y-IN VIDEO-IN S-VIDEO-C-IN GND SP861 SPEAKER L-CH (NO CONNECTION) SP(L) SP(L) SP-GND SP-GND E F FL11.8SCJ Function Schematic Diagram C107 1 D103 L-53HT STANDBY R950 220 RS101 KSM-712TH2E (REMOTE SENSOR) D104 333GT/E POWER R108 220 C950 OPEN R109 220 C106 OPEN C105 OPEN CN101B 1 2 3 4 5 6 7 8 VOUT Vcc GND 2 R107 3.3K R106 100 D950 LTL-307Y DVD 1 2 3 R110 1K D952 OPEN C103 47/16V C111 OPEN C110 OPEN C104 330P C109 0.1 D101 EDZTE61 6.8B R111 18K R112 8.2K R113 4.7K R114 2.7K R115 4.7K R116 220 R118 10K SW104 VOL DOWN SW105 VOL UP SW106 MENU SW107 CH DOWN SW108 CH UP SW109 POWER R955 OPEN R954 OPEN R953 2.2K R952 2.2K SW955 OPEN SW954 OPEN SW953 EJECT SW952 STOP 1 D105 OPEN TO MAIN CBA CN102 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED C108 0.1 R956 10K R951 WIRE SW951 PLAY D951 OPEN C951 0.1 FUNCTION CBA UNLESS OTHERWISE SPECIFIED: SWITCHES ARE SKHHLMA010. A B C 11-8 FL11.8SCF Digital Main 1 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT TO MAIN CBA CN303 4 3 CN3003 GND 29 DVD-SPDIF 28 GND 27 DVD-AUDIO(R) 26 DVD-AUDIO-MUTE 25 DVD-AUDIO(L) 24 GND 23 DVD-Y 22 GND 21 DVD-Pb 20 GND 19 DVD-Pr 18 GND 17 LED-CONT 16 DVD-DISC-OUT 15 GND 14 DVD-SCLK 13 GND 12 DVD-CS 11 GND 10 DVD-DISC-IN 9 DVD-SDATA 8 DVD-REMOTE 7 DVD-P-ON 6 DVD-MAIN-PWR 5 P-ON-H3(NU) 4 DVD-LED 3 KEY-IN2 2 GND 1 CONTINUE DIGITAL 4 DVD-LED DVD-MAIN-PWR DVD-P-ON DVD-SDATA DVD-CS DVD-SCLK LED-CONT CONTINUE DIGITAL 3 KEY-IN2 DVD-AUDIO(L) DVD-SPDIF DVD-AUDIO-MUTE DVD-AUDIO(R) R3417 100 C3295 33P R3419 680 C3296 OPEN C3294 33P R3420 100 R3473 680 C3266 OPEN R3418 1000P R3474 1000P C3267 33P CONTINUE DIGITAL 5 LCD+12V C3268 33P 8 C3269 33P R3471 100 R3472 100 C3270 100P C3271 100P 1 R3425 100 C3272 100P R3426 100 C3273 100P R3427 100 C3281 1000P C3280 100P C3279 100P C3278 100P C3277 100P C3276 100P C3275 100P R3430 100 R3433 100 6 5 R3007 OPEN 2 3 4 R3006 OPEN Q3001 OPEN R3428 100 R3432 100 7 Q3002 OPEN C3002 OPEN C3078 OPEN R3002 OPEN R3001 OPEN R3429 100 C3274 100P CONTINUE DIGITAL 2 DVD-REMOTE DVD-DISC-IN DVD-DISC-OUT DVD-Pr DVD-Pb DVD-Y *1 IC3005(1/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 0 0 0 0 OPEN OPEN 0 0 0 0 OPEN OPEN OPEN OPEN 0 0 OPEN OPEN R3123 R3121 OPEN OPEN R3152 1K R3127 R3126 R3129 R3128 R3088 5.6K A B CN3005 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO LCD MODULE ASSEMBLY GND LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) GND LLVCLK(+) LLVCLK(-) GND LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) GND TP POL CPV OE1 XA0 STV CONTINUE DIGITAL 5 P-ON+3.3V TO DIGITAL MAIN 2 IC3005(2/6) REFR W14 TO LCD MODULE ASSEMBLY LCD+12V LCD+12V LCD+12V LCD+12V LCD+12V GND GND GND RX0(+) RX0(-) RX1(+) RX1(-) RX2(+) RX2(-) GND RXCLK(+) RXCLK(-) GND RX3(+) RX3(-) NU NU NU NU GND GND GND GND GND GND GND OPEN R3165 R3166 R3167 R3168 R3115 R3113 R3169 R3170 R3112 R3114 R3116 R3117 R3118 R3119 R3120 R3122 R3124 R3125 R3155 0 0 R3161 OPEN 1 R3164 R3163 OPEN OPEN OPEN OPEN OPEN LVDS TX AA17 AB17 Y16 W16 AB16 AA16 AB15 AA15 Y15 W15 AB14 AA14 AB13 AA13 Y13 W13 Y12 W12 AB12 AA12 Y11 W11 AB11 AA11 R3157 R3158 R3159 R3160 R3162 2 CN3004 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 OPEN 0 OPEN 0 CONTINUE DIGITAL 4 STV RESET-LCD OE CPV POL TP CONTINUE DIGITAL 2 RESET-LCD C D 11-9 E F FL11.8SCD1 Digital Main 2 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3144 100 R3142 100 R3138 100 DIGITAL MAIN CBA UNIT *1 IC3005(2/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 4 TO DIGITAL MAIN 3 IC3005(3/6) R3193 4.7K R3369 L3024 C3243 OPEN OPEN OPEN F1 DEMODULATOR /MPEG DECODER C3226 10P R3361 0 R3354 0 R3345 0 R3338 0 IC3012 AT24C02BN-SH-T (MEMORY) F2 C3219 C3220 C3221 C3222 0.1 10 0.1 0.1 R3344 0 R3337 0 C3225 10P A1 NU E2 NU E1 NU R3194 2.2K R3202 2.2K IF-AGC J1 C3177 0.33 C3178 0.1 R3353 0 R3360 0 L3023 OPEN C3242 R3368 OPEN OPEN C3084 OPEN HDMA-SCL Y18 HDMI-SDA W19 R3188 R3187 R3218 R3190 10K WP 7 3 A2 SCL 6 4 GND SDA 5 C3211 0.1 DVD-DISC-IN N21 DVD-DISC-OUT M19 R3228 22 R3467 R3466 OPEN OPEN R3229 22 R3296 R3298 C3194 C3195 C3196 HSIN B14 VSIN B15 C11 C8 D9 C3197 C3198 C3199 C3200 C3201 C3202 C14 A11 B12 D8 A8 B7 NU A10 NU C7 A12 G C3093 33P C3098 33P Q3033 2SC4081UBTLQ (BEFFER) R3436 10K R3297 OPEN R3295 OPEN R3156 100 R3172 100 R3435 100 C3099 100P C3101 100P C3100 33P C3102 33P C3103 33P R3175 100 100 100 0.1 0.1 0.1 0.01 0.1 0.1 0.1 0.1 0.1 C3104 33P IC3013 SN74LVC1G126DCKR (BUFFER GATE) 1 VCC 5 C3293 OPEN C3292 OPEN C3291 OPEN R3403 R3402 R3401 R3400 R3399 C3105 1000P C3112 100P R3154 R3171 R3179 C3214 0.1 2 C3107 33P R3181 0 C3111 100P 100 100 0 3 GND 4 IC3014 SN74LVC1G126DCKR (BUFFER GATE) 1 VCC 5 0 0 0 0 0 3 GND R3398 0 C3203 0.1 D3027 D3040 1SS400 1SS400 R3343 100 C3290 C3284 C3285 C3286 0.01 0.1 0.1 0.1 H D3050 OPEN R3347 10K R3286 47 Q3010 OPEN R3460 0 R3459 0 R3458 0 JK3001 D-SUB CONNECTOR R3183 OPEN 91 91 91 R3184 OPEN R3356 75 D3049 OPEN R3364 75 D3053 OPEN R3377 75 D3055 OPEN R3186 OPEN I J 11-10 CN3006 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO MAIN CBA CN302 KEY-IN1 DIF-OUT2 GND DIF-OUT1 GND IF-AGC RESET SCL SDA AUDIO-MUTE COM-VIDEO-Pr-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Y-IN GND AUDIO(L) INPUT0 AUDIO(R) INPUT1 GND S-VIDEO-Y-IN GND S-VIDEO-C-IN S-VIDEO-SW VIDEO-IN GND SPDIF GND CONTINUE DIGITAL 3 AUDIO(L) AUDIO(R) SPDIF CONTINUE DIGITAL 6 WP HDMI-SDA HDMI-SCL CONTINUE DIGITAL 1 RESET-LCD D3045 OPEN R3416 R3185 OPEN OPEN R3476 R3477 R3478 0.1 0.1 0.1 0.1 0.1 0.1 0.1 R3358 10K R3284 47 R3285 47 C3204 C3205 C3206 C3207 C3208 C3209 C3210 R3376 100 R3180 OPEN CONTINUE DIGITAL 3 KEY-IN1 LIGHT-SENS RESET CONTINUE DIGITAL 5 P-ON+5V AL+3.3V-2 P-ON+3.3V 4 R3339 100 OPEN OPEN OPEN TO DIGITAL TO DIGITAL MAIN 6 MAIN 1 IC3005(6/6) IC3005(1/6) C3092 1000P 2 A15 C12 A7 B8 B6 C9 E3 B9 A13 A14 B13 B11 A9 A6 B10 D3041 OPEN C3095 33P C3287 C3288 C3289 1 NU NU NU NU NU NU NU NU NU NU NU R3321 4.7K R3333 100 R3334 100 C3089 33P OPEN OPEN OPEN OPEN OPEN OPEN DIGITAL SIGNAL PROCESS NU DVD-Y DVD-Pb DVD-Pr R3326 4.7K 22 22 22 C3259 C3257 C3258 C3254 C3255 C3256 A/D CONVERTER R3310 10K R3437 10K R3219 22 SW VCC 8 2 A1 C3074 1000P R3189 10K DVD-REMOTE W18 2 1 A0 Q3012 2SK3018 (BUFFER) D3054 OPEN INPUT0 K1 INPUT1 L4 S-VIDEO-SW AB22 3 R3134 100 C3086 1000P Q3011 2SK3018 (BUFFER) C3235 33P L3022 0.27uH C3087 33P R3404 100 D3056 OPEN R3192 4.7K CONTINUE DIGITAL 4 AUDIO-MUTE SDA SCL 11 6 1 12 7 2 13 8 3 14 9 4 15 10 5 CONTINUE DIGITAL 1 DVD-REMOTE DVD-DISC-IN DVD-DISC-OUT DVD-Pr DVD-Pb DVD-Y K L FL11.8SCD2 Digital Main 3 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT 4 CONTINUE DIGITAL 2 AUDIO(L) AUDIO(R) SPDIF R3335 R3336 3.9K 3.9K L3038 BLM21PG221SN1D R3331 OPEN R3327 OPEN L3040 BLM21PG221SN1D IC3017 SN74LVC1G126DCKR (BUFFER GATE) 1 VCC 5 3 GND C3250 0.1 IC3015 NJM4558M(TE1) (OP AMP) *1 IC3005(3/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER R3320 OPEN C3224 10 C3248 220P R3325 4.7K C3249 10 R3362 0 C3245 OPEN R3332 4.7K C3229 82P LRCLK M1 ACLK L3 M2 DVD-AUDIO-MUTE M3 BCLK L1 STXD0 AB10 SRXD0 AA10 SCLK0 Y10 SPDIF L2 DTV-ON-H1 M21 P-ON-H2 K20 HDMI-HPD1 J19 HDMI-HPD0 J20 REMOTE K21 HDMI-CEC K22 RESET-N T20 NU P18 HDMI-HPD2 J22 VCOM-PWM AB21 TO DIGITAL MAIN 2 IC3005(2/6) 2 AUDIO I/F TO DIGITAL MAIN 6 IC3005(6/6) MADIN0 KEY-IN1 KEY-IN2 PROTECT1 PROTECT2 PROTECT3 DTV-ON-H2 LED-R C4 NU C3 C1 NU C2 NU B2 NU B1 B5 NU B4 A2 NU A3 NU A4 NU A5 NU B3 1 M OPEN OPEN OPEN 100 OPEN OPEN OPEN OPEN 100 100 R3211 R3212 R3213 22 22 22 2 6 15 14 13 5 LPF LPF 3 GND 4 IC3010 OPEN AUDIO D/A CONVERTER R3355 R3350 24K 150K C3237 82P R3342 4.7K 2 3 R3214 R3205 22 100 R3312 R3313 R3314 R3315 R3316 R3317 R3318 R3465 22 OPEN 22 22 22 22 22 22 C3215 0.1 C3216 10 4 5 10 NU AUDIO SERIAL PORT 6 7 8 C3232 82P IC3009 PST8420UR (RESET) 1 GND OUT 4 R3178 10K C3106 0.1 C3252 0.1 R3191 100 R3182 4.7K C3116 OPEN CD 3 CONTINUE DIGITAL 6 HDMI-CEC HDMI-HPD0 HDMI-HPD1 HDMI-HPD2 CONTINUE DIGITAL 2 KEY-IN1 LIGHT-SENS RESET CONTINUE DIGITAL 5 PROTECT1 PROTECT2 PROTECT3 DTV-ON-H2 DTV-ON-H1 LED-R P-ON-H2 REMOTE VCOM-PWM 22 R3446 10K C3218 10 C3283 10 R3445 CONTINUE DIGITAL 1 KEY-IN2 DVD-AUDIO(L) DVD-SPDIF DVD-AUDIO-MUTE DVD-AUDIO(R) 1K R3447 10K N C3120 0.01 CONTINUE DIGITAL 4 CPU-RESET-N MADIN0 C3113 0.033 R3475 100K R3444 C3109 OPEN 9 NU C3217 10 C3282 10 R3173 OPEN ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR SYSTEM CLOCK MANAGER SERIAL CONTROL PORT 1 12 11 GND VCC DAC DAC 4X/8X OVERSAMPLING DIGITAL FILTER /FUNCTION CONTROLLER ZERO DETECT 2 VDD H19 G21 G20 H21 G22 H22 H20 J21 G1 G2 NU G3 R3195 R3196 R3197 R3208 R3198 R3199 R3200 R3201 R3209 R3210 8 7 VCC 1 R3394 12K C3110 OPEN C3230 82P R3440 100 4 R3176 OPEN C3108 OPEN R3341 4.7K R3393 12K R3438 OPEN 3 R3330 4.7K R3174 OPEN L3013 OPEN R3177 OPEN 16 C3251 100/16V R3439 100 4 2 C3223 R3322 10 4.7K C3227 82P 2 3 GND C3241 82P R3359 R3352 R3351 0 24K 150K R3311 OPEN IC3016 SN74LVC1G126DCKR (BUFFER GATE) 1 VCC 5 CONTINUE DIGITAL 4 C7-SPD-EN DVD-SPD-EN C3244 OPEN CONTINUE DIGITAL 5 P-ON+3.3V P-ON+5V AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT AL+3.3V O P 11-11 Q R FL11.8SCD3 Digital Main 4 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3064 100 *1 IC3005(4/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER C3050 0.1 DVD-CS U21 R5 SD-VREF0 V7 SD-VREF1 R3065 100 4 C3029 C3030 C3031 C3032 C3033 C3034 C3035 C3036 C3037 C3038 C3039 C3040 C3041 C3042 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 IC3002 K4T51163QG-HCF7 (DDR2 SDRAM) *A VDD 1-V3 2-V3 3-V3 SD-DQ8 SD-DQ14 SD-DQ15 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ13 3 4-V3 5-V3 6-V3 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ3 SD-DQ4 SD-DQ2 SD-DQ1 SD-DQ0 SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 C3009 0.1 VREF J2 CKE CK CK CS RAS CAS WE BA2/NU BA1 BA0 A12 A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ODT R3026 100 C3010 R3027 0.1 100 K2 J8 K8 L8 K7 L7 K3 L1 L3 L2 R2 P7 M2 P3 P8 P2 N7 N3 N8 N2 M7 M3 M8 K9 E2 A2 R8 R7 R3 NU NU NU NU NU B7 A8 B3 B9 B1 D9 D1 D3 D7 C2 C8 F7 E8 F3 F9 F1 H9 H1 H3 H7 G2 G8 UDQS UDQS/NU UDM DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 LDQS LDQS/NU LDM DQ7 DQ6 DQ5 DQ4 DQ3 VSS *B DQ2 *A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1 DQ1 *B:A3,A7,B2,B8,D2,D8,E3,E7, DQ0 F2,F8,H2,H8,J3,J7,N1,P9 R3049 120 2 IC3006 W25X32VSSIGE (MEMORY) R3104 10K 1 (USB JACK) USB+5V USB(-) USB(+) GND CN3009 1 L3025 2 3 4 1 CS VCC 8 2 SO NU 7 3 WP SCK 6 4 GND SI 5 EXC24CG900U C3246 1 R3102 10K L3004 BLM21PG221SN1D R3107 10K C3073 0.1 R3071 130 D3052 OPEN R3153 330 R3108 10K R3441 OPEN S Q3009 2SB1732TL (SW+5V) R3150 10K C3096 1 R3146 1K R3147 10K R3151 330 Q3008 2SC4081UBTLQ (SWITCHING) T R3148 15K C3091 OPEN D3002 AS431AKTR-E1 DVD-SDATA M32TRST-N RESET-LCD LED-CONT DVD-SCLK ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS BACKLIGHT-ADJ C7-SPD-EN LED1 DVD-LED C3051 0.1 P2 N4 T2 R4 P4 R2 R3 R1 V1 T4 W2 V4 W3 W1 U4 V2 N3 U3 P1 N2 U1 U2 SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 SD-UDM SD-LDM SD-UDQSN SD-UDQS SD-LDQSN SD-LDQS AB2 AA3 W6 Y4 AA1 Y2 W8 AA2 AB8 AB5 AB6 AA7 AA5 AA8 AB4 AA6 AA4 AB7 W5 W7 AB3 Y8 Y6 W9 AA9 SD-RAS SD-CAS SD-WE SD-CS SD-CLKN SD-CLK SD-CKE SD-ODT SD-A12 SD-A11 SD-A10 SD-A9 SD-A8 SD-A7 SD-A6 SD-A5 SD-A4 SD-A3 SD-A2 SD-A1 SD-A0 SD-BA2 SD-BA1 SD-BA0 NU 3-S3 6-S3 2-S3 1-S3 5-S3 4-S3 R3029 R3030 R3031 R3028 R3024 R3015 R3016 R3048 R3035 R3036 R3037 R3038 R3039 R3040 R3041 R3042 R3043 R3044 R3045 R3046 R3047 R3032 R3033 R3034 R3070 22 22 22 22 4.7 4.7 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 130 R3091 R3092 R3089 R3094 R3093 47 47 47 47 47 CPV STV TP NU OE POL AUDIO-MUTE GPY10 T19 U22 V22 L21 U20 P22 R21 P19 P20 P21 M22 N22 W17 Y17 K19 L20 R3451 R3226 R3227 R3449 R3225 R3448 R3215 R3216 R3217 R3230 R3231 R3232 R3233 AA18 AA19 AB19 R3454 22 AA20 AB20 Y19 L19 L22 TXD0 R19 RXD0 R20 R3234 R3421 10K 100 R3422 100 R3468 100 R3469 100 XIN25 T22 XOUT25 T21 DVD-MAIN-PWR DVD-P-ON BACKLIGHT-SW P-ON-H1 OE2 U19 V20 W20 Y22 AB18 C3184 15P X3001 25MHz C3183 15P R3235 1M R3223 510 R3442 R3443 R3095 R3096 R3090 22 22 R3224 10K 100 22 22 22 R3098 4.7K NU J3 NU F22 AA21 WP AA22 SOUT Y20 CS V19 SCK Y21 SIN NU J4 NU H3 SCL K3 SDA K2 R3396 4.7K C3253 OPEN R3461 R3462 R3463 R3131 22 R3470 100 R3099 6.04K C3076 10 C3075 0.1 C3072 10 C3071 0.1 R3206 R3207 R3140 33K R3141 180 22 22 CONTINUE DIGITAL 1 DVD-LED DVD-MAIN-PWR DVD-P-ON DVD-SDATA DVD-CS DVD-SCLK LED-CONT CONTINUE DIGITAL 6 GPIO6 CONTINUE DIGITAL 5 GPY10 P-ON-H1 LED1 BACKLIGHT-SW BACKLIGHT-ADJ CPU-RESET-N OE2 CONTINUE DIGITAL 3 CPU-RESET-N MADIN0 CONTINUE DIGITAL 5 P-ON+1.8V P-ON+3.3V L3043 BLM21PG221SN1D AL+3.3V P-ON+5V R3204 4.7K R3203 4.7K R3136 1.6 L3041 BLM21PG221SN1D 100 100 100 (NO CONNECTION) P-ON+5V UART0-TX UART0-RX GND CONTINUE DIGITAL 2 AUDIO-MUTE SDA SCL R3139 33K R3135 2.4 CN3010 1 2 3 4 R3395 4.7K 22 22 22 22 OPEN W22 V21 H2 H1 (NO CONNECTION) P-ON+5V UART0-TX NU NU UART0-RX M32TDI AL+3.3V M32TDO M32TRST-N RESET-LCD GND M32TMS ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS CPU-RESET-N CONTINUE DIGITAL 3 C7-SPD-EN DVD-SPD-EN CONTINUE DIGITAL 1 STV RESET-LCD OE CPV POL TP 22 22 22 10K 22 22 22 USB-EN W21 DVD-SPD-EN GPIO6 USB(+) USB(-) CN3007 1 2 3 4 5 R3452 OPEN 6 7 R3450 OPEN 8 9 10 R3453 11 OPEN 12 13 14 15 16 17 18 19 20 DIGITAL MAIN CBA UNIT U V 11-12 W X FL11.8SCD4 Digital Main 5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3068 R3058 R3083 DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 3 PROTECT1 PROTECT2 PROTECT3 DTV-ON-H2 DTV-ON-H1 LED-R P-ON-H2 REMOTE VCOM-PWM CONTINUE DIGITAL 4 GPY10 P-ON-H1 LED1 BACKLIGHT-SW BACKLIGHT-ADJ CPU-RESET-N OE2 CONTINUE DIGITAL 4 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V CONTINUE DIGITAL 1 P-ON+3.3V 100 100 100 *1 IC3005(5/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 2 *A:L9~L14,M13,M20, N18~N20,P9,V6, V8,V16 *B:K9~K14,K18,M5, M9~M12,M18,N9, N12,P3,P5,P12, P14,R18,T3,U5, U18,V5,V9,V12, V14,V17,W4,Y3, Y7,Y14,AB1,AB9 1 R3221 100 IC3004 BD7820FP-E2 (+1.8V REG.) AVDD33 AVDD33 AVDD33 AVDD33 AVDD33 VDD33HDMI VDD33HDMI VDD33HDMI VDD33HDMI VDD33IO AVDD33PLL AVDD33AUD MIXVDD33 MIXVDD33 MIXVDD33 MIXVDD33 MIXVDD33 C3124 0.1 C3125 0.1 C3126 0.1 C3127 0.1 C3128 0.1 C3129 0.1 C3130 0.1 C3131 0.1 C3132 0.1 C3133 10 C3134 OPEN C3136 0.1 C3137 0.1 C3138 0.1 C 1 2 3 4 5 R3009 100 R3017 OPEN C3004 1000P L3001 2uH C3023 10 C3018 100/16V C3024 10 C3027 0.1 R3061 1K R3060 1K R3059 390 C3049 100/4V C3263 1 C3139 10 C3140 0.1 C3141 0.1 C3142 0.1 C3143 0.1 C3144 0.1 C3145 0.1 Q3003 2SC4081UB-TLQ (SWITCHING) Q3004 R3079 2SC4081UB-TLQ 10K (SWITCHING) CONTINUE DIGITAL 2 P-ON+5V AL+3.3V-2 P-ON+3.3V CONTINUE DIGITAL 6 AL+3.3V-2 P-ON+3.3V C3054 1 R3086 2.2K R3084 2.2K R3077 10K L3014 BLM21PG221SN1D C3114 10 C3115 100 C3117 0.1 C3118 0.1 C3119 0.1 C3146 0.1 C3147 0.1 C3148 0.1 C3149 0.1 C3150 0.1 C3153 OPEN C3264 0.01 C3151 0.1 C3152 0.1 C3155 10 C3156 0.1 C3160 0.1 C3161 0.1 1 2 3 4 5 C3068 10 C3069 10 D3105 1SS400 C3053 0.1 R3110 1K R3109 390 C3070 0.1 R3111 1K C3162 0.1 C3082 0.1 C3081 10 R3062 OPEN R3424 D3103 100 1SS400 L3003 BLM21PG221SN1D C3080 10 C3165 0.1 C3170 0.1 C3171 0.1 C3172 0.1 C3166 0.1 C3167 10 C3168 0.1 C3169 0.1 C3174 0.1 C3175 0.1 Q3101 2SC4081UB-TLQ (SWITCHING) C3265 10 R3097 2.2K C3176 10 R3340 6.8K 2 VIN 3 SW 4 GND R3100 22K C3011 0 C3008 100P R3050 0 C3015 10 C3016 0.1 R3054 0 C3019 10 C3022 0.1 C3028 10 C3043 0.1 R3063 OPEN D3001 SK22A L3044 BLM21PG221SN1D R3066 0 C3046 1000P C3094 47/4V C3097 10 C3047 0.1 100 C3048 1000P R3101 100 C3067 1000P R3133 10K R3087 R3085 R3078 R3074 R3149 0 R3145 6.04K C3057 1000P R3143 15K Z AA BB 11-13 C3055 1000P C3062 1000P C3090 1 R3137 6.8K C3088 0.015 C3044 1000P R3464 OPEN D3101 1SS400 D3102 1SS400 EN 7 FB 5 C3045 10 R3072 Q3006 2SA1774 (SWITCHING) COMP 6 L3009 10uH C3231 0.1 C3228 0.1 R3106 22K R3105 1K Q3005 2SC4081UB-TLQ IC3008 (SWITCHING) BD9321EFJ-E2 (DC-DC CONVERTER) C3083 0.1 1 BST SS 8 C3085 0.1 R3319 1K C3006 1000P R3423 47K L3020 BLM21PG221SN1D C3173 0.1 R3003 OPEN C3005 1000P R3073 0 D3104 1SS400 C3164 0.1 100 100 C3077 100/16V D3106 1SS400 L3019 BLM21PG221SN1D C3163 10 R3011 R3014 R3005 OPEN C3157 0.1 C3052 10 C3159 0.1 R3004 OPEN BC3001 2.2uH L3017 BLM21PG221SN1D C3066 220/16V C3154 10 CONTINUE DIGITAL 1 LCD+12V IC3007 BD7820FP-E2 (+1.8V REG.) C3079 100/4V CONTINUE DIGITAL 6 HDMI-VDD33 Y 100 L3016 BLM21PG221SN1D C6 C13 D2 D10 E8 E18 G18 E17 J18 D14 H5 F5 D1 D5 E4 E5 F4 REXT D11 LPF H4 C3123 0.1 C N1 N5 T1 T5 V3 Y1 Y5 Y9 J9 J10 J11 J12 E10 E12 D13 J13 E15 C3122 0.1 OUT VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VDD18 VDD18 VDD18 VDD18 AVDD18 AVDD18 VDD18HDMI VDD18HDMI VPPOTP C3121 0.1 OUT M4 V13 V15 V18 W10 P10 N10 P11 P13 T18 L3015 BLM21PG221SN1D R3010 GND VCCQ33 VCCQ33 VCCQ33 VCCQ33 VCCQ33 PLLAVCC PLLAVCC PLLAVCC PLLAVCC PLLAVCC C3003 100P VCC *A V10 N11 V11 N13 N14 R3008 100 R3222 10K C3182 0.1 C3181 0.1 VDD12 PLLDVDD PLLDVDD PLLDVDD PLLDVDD PLLDVDD Q3013 SSM3K309T (SW+3.3V) GND C3179 0.1 R3220 0 VCC C3180 0.1 CTL K5 J2 K4 R22 L18 M14 CTL VDDA33RU VDDA33USB VDDA33USB VCC33STB VCC33STB VDDSTB S 3 VSS NU NU AVSS18 AVSS18 AVSS AVSS AVSS AVSS AVSS VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSIO AVSS33PLL AVSS33AUD AVSS33AUD MIXVSS33 MIXVSS33 MIXVSS33 VSSAUSB G *B C5 D4 E9 E11 C10 D3 D7 D12 E7 E13 E16 F18 G19 H18 J14 E14 J5 G4 G5 D6 E6 F3 L5 D 4 CC C3061 1000P C3063 0 OPEN OPEN 100 100 TO MAIN CBA CN301 VCOM-PWM BACKLIGHT-ADJ LED1 BACKLIGHT-SW REMOTE OE2 GND AL+3.3V AL+3.3V P-ON+3.3V P-ON+3.3V GND GND P-ON+7V PROTECT2 P-ON+5V P-ON+5V/LED-R GND PROTECT1 P-ON+3V P-ON-H1 AMP(R)-OUT GND AMP(L)-OUT PROTECT3 GND GND GND P-ON-H2 CONTINUE DIGITAL 3 P-ON+3.3V P-ON+5V AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT AL+3.3V CN3002 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C3065 0 DD FL11.8SCD5 Digital Main 6 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. *1 IC3005(6/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER DIGITAL MAIN CBA UNIT R3244 R3243 R3242 R3241 R3240 R3239 R3238 R3261 C19 C20 D19 D20 A21 A22 B21 B22 DDC0-SCL A16 DDC0-SDA C16 4 3 R3252 R3251 R3250 R3249 R3248 R3247 R3246 R3245 TO DIGITAL MAIN 3 IC3005(3/6) VIDEO DECODER PLL-XFC-P E22 PLL-XFC-X E21 0 0 0 0 0 0 0 0 R3275 OPEN R3387 R3370 OPEN OPEN R3237 27K CONTINUE DIGITAL 2 L3032 EXC28CG900U R3391 0 C3185 0.01 R3236 560 R3292 OPEN Q3022 OPEN (BUFFER) C3262 OPEN R3411 OPEN R3300 OPEN R3272 6.8K 1 R3273 47K R3301 10K C3261 1 Q3020 2SK3018 (BUFFER) R3410 2.7K D3058 1SS400 R3413 OPEN R3373 OPEN Q3015 R3266 2SK3018 4.7K (BUFFER) C3189 0.022 R3382 0 R3366 0 R3276 R3388 47K 0 Q3024 2SK3018 (BUFFER) R3293 10K R3270 C3187 4.7 7.5K C3186 0.1 R3271 C3188 2200P 3K R3407 1K R3263 4.7K R3383 10K L3034 EXC28CG900U Q3016 R3267 2SK3018 4.7K (BUFFER) R3405 100 R3264 4.7K L3036 EXC28CG900U Q3019 OPEN (BUFFER) R3415 82K D3057 RB751S-40TE61 C3190 OPEN Q3017 R3268 OPEN OPEN (BUFFER) Q3034 2SC4081UBTLQ (SWITCHING) WP HDMI-SDA HDMI-SCL R3412 OPEN R3408 OPEN 0 0 0 0 0 0 0 0 IC3011 BU9883FV-WE2 (HDMI SERIAL EEPROM) R3262 OPEN L3039 BLM21PG221SN1D CONTINUE DIGITAL 4 GPI06 R3371 OPEN R3386 OPEN R3260 R3259 R3258 R3257 R3256 R3255 R3254 R3253 R3456 4.7K 1 VCC1 VCC2 16 2 SCL1 SCL2 15 3 SDA1 SDA2 14 4 WPB R3455 4.7K CONTINUE DIGITAL 3 HDMI-CEC HDMI-HPD0 HDMI-HPD1 HDMI-HPD2 OPEN OPEN R3278 OPEN D3060 OPEN Q3018 2SK3018 (BUFFER) CONTINUE DIGITAL 5 AL+3.3V-2 P-ON+3.3V HDMICONNECTOR-1 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT R3390 OPEN CONTINUE DIGITAL 5 HDMI-VDD33 Q3014 2SK3018 (BUFFER) Q3030 OPEN (SWITCHING) JK3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 R3372 19 1K L3028 OPEN PWR0 C15 PWR1 B16 PWR2 C18 TO DIGITAL PLL-XFC-A F21 MAIN 2 IC3005(2/6) 2 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN L3030 EXC28CG900U A17 B17 A18 B18 A19 B19 A20 B20 DDC2-SCL D17 DDC2-SDA C17 EXT-RES D18 AUDIO DECODER HDMICONNECTOR-3 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT R3381 R3365 C21 C22 D21 D22 E19 E20 F19 F20 DDC1-SCL D15 DDC1-SDA D16 HDMI I/F JK3002 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 L3026 OPEN C3192 0.1 R3282 100 R3281 100 5 VCC-OUT 6 SDA0 NU 13 C3191 0.1 R3392 0 R3384 R3367 C3212 0.1 C3213 0.1 GND 12 SDA3 11 7 SCL0 SCL3 10 8 VCC0 VCC3 9 R3294 10K R3274 47K Q3023 2SK3018 (BUFFER) R3277 47K 0 0 R3389 0 R3374 1K C3260 R3409 1 2.7K D3059 1SS400 R3302 10K Q3031 2SC4081UBTLQ (SWITCHING) JK3004 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 HDMICONNECTOR-2 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT R3414 OPEN R3375 OPEN R3406 1K R3385 10K EE FF GG HH 11-14 II Q3032 2SC4081UBTLQ (SWITCHING) JJ FL11.8SCD6 DVD Main 1 Schematic Diagram 2 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. DVD MAIN CBA UNIT CONTINUE DVD MAIN 2 FD-OFST TD-OFST VREFH VREF165 SLD STBY FOCUS DRIVE TRACKING DRIVE SPDL LPCO1 LPCO2 LPC VIN1RF VIN2RF VIN3RF VIN4RF VIN5 VIN6 VIN7 VIN8 CD/DVD IC202 LM324PWR (OP AMP) 1 2 3 VCC 4 5 6 7 R280 1K R281 10K R283 10K R279 47K R277 47K C281 0.1 R278 47K R285 22K R269 2K C289 3300P C288 3300P R284 10K R282 10K R234 R233 R232 R231 CONTINUE DVD MAIN 2 LOAD-DISC SP-ROT SL-ADS 8 CONTINUE DVD MAIN 2 EV+1.2V EV+3.3V(D) EV+3.3V(A) CONTINUE DVD MAIN 3 EV+3.3V(D) R264 1K C280 0.1 R286 2.2K C284 6800P R276 47K 1K 1K 1K 1K R813 0 R815 4.7K 2.2K 2.2K 2.2K 2.2K 1 1 1 1 4 14 13 12 11 10 9 GND R225 R226 R227 R228 C217 C218 C219 C220 3 PICK UP UNIT TS FS DETECTOR 7 9 11 2 3 6 5 4 2 SPINDLE MOTOR DRIVE CBA M L201 47uH C201 0.1 TS(+) FS(+) FS(-) TS(-) GND(CD-PD) GND(DVD-PD) PD-MONI DVD-LD GND(LD) CD-LD GND NU VREF NU B C A D CD/DVD DVD-ON+5V SP(+) SP(-) GND SL(-) SL(+) LOAD-DISC M SLED MOTOR CN201 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 C232 0.01 R251 3.3 Q253 KTC3875SGR-RTK/P (AMP) C259 1 C313 220P R308 68K C253 R255 100/6.3V 560 R252 2.2 C802 0.01 SENSOR CBA A 1 STBY 28 2 27 3 26 4 25 5 24 6 23 7 GND 22 DET. AMP R313 10K C311 0.1 C302 820P C421 47P C422 47P C423 47P R302 220 C314 3300P R301 R305 1.5K 1K C301 0.1 C425 47P C426 47P C427 47P C305 6800P DET. AMP R258 180 IC201 SN74LVC1G3157DCKR (SW) 6 0.1 GND VCC 21 8 VCC VCC 5 3.3 4 0 C215 0.1 9 VCC 20 10 GND GND 19 11 C317 0.1 R319 1.5 C318 0.1 R818 1K 12 13 14 R320 1.5 SPINDLE MOTOR DRIVE SLED MOTOR DRIVE 18 TRACKING ACTUATOR DRIVE FOCUS ACTUATOR DRIVE 16 17 R471 100K C316 0.1 1 VCC D 11-15 E CONTINUE DVD MAIN 2 DVD-P-ON DVD-SCLK DVD-SDATA DVD-CS DVD-REMOTE PWRCON RESET CONTINUE DVD MAIN 3 RESET *2 R318 1.5 C 1K 1K 1K 1K 1K 1K C473 0.1 15 R817 1K B R411 R403 R406 R404 R407 R402 C471 0.1 C315 0.1 R317 1.5 C310 0.1 R816 15K R812 15K TO MAIN CBA CN901 AV+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON C257 1 Q251 KTC3875SGR-RTK/P (AMP) DISC-OUT CONTINUE DVD MAIN 2 DVD-DISC-IN DVD-DISC-OUT R315 91K C308 0.039 C250 0.1 C804 0.1 R805 R806 0 0 DISC-IN R268 180 0 3 Q804 KTA1504SY-RTK/P (LED DRIVE) C801 0.01 IC301 SA5624G (SERVO DRIVE) C303 68P R322 10K 0.3 (0) 1 0 2 R801 R803 4.7K 4.7K R265 470 R303 22K Q252 KTA1504SY-RTK/P (AMP) C233 0.01 R811 10K 1 C263 47 /6.3V R262 2.2 Q254 KTA1504SY-RTK/P (AMP) CN301 1 2 3 4 5 R325 1K 6 CN801 LED-POWER 1 DVD-DISC-OUT 2 DVD-DISC-IN 3 GND 4 C210 0.1 R261 5.6 LOAD-DISC CN5001 1 2 3 4 C202 180P C203 0.1 CN401 1 2 3 4 C417 C408 5 L401 150P 330/6.3V 0 6 C418 7 L402 0.1 0 8 9 L403 C402 C416 10 0 0.1 0.1 11 12 C405 0.1 13 14 C403 15 0.1 16 17 C412 C411 C410 18 0 0 0 19 20 21 22 23 24 25 26 3 2 1 3 VOUT GND VCC VOUT GND NU NU 5 IC461 4 2 IC462 BMR-110529 PST3229NR (RESET) (RESET) F FL11.8SCDV1 DVD Main 2 Schematic Diagram CONTINUE DVD MAIN 3 FDQ(0~15) CONTINUE DVD MAIN 3 MA(0~10) MDQ(0~15) FADR(0~19) FDQ3 FDQ11 FDQ4 FDQ12 FDQ5 FDQ13 FDQ6 FDQ14 FDQ7 FDQ15 R141 10K 3 CONTINUE DVD MAIN 1 DVD-P-ON DVD-SCLK DVD-SDATA DVD-CS DVD-REMOTE PWRCON RESET 72-I1 75-G1 74-H1 76-G1 68-G1 69-G2 70-I1 CONTINUE DVD MAIN 1 DVD-DISC-IN DVD-DISC-OUT 78-H1 79-H1 30-L2 FADR18 FADR17 FADR7 FADR6 FADR5 FADR4 FADR3 FADR2 FADR1 69-G2 R131 10K 68-G2 75-G2 76-G2 1 EXT MEMORY DATA1 EXT MEMORY EXT MEMORY EXT MEMORY GND VDD(+3.3V) EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY GND VDD(+3.3V) EXT MEMORY EXT MEMORY GND VDD(+1.2V) EXT ADR16 EXT ADR15 EXT ADR14 EXT ADR13 EXT ADR12 EXT ADR11 EXT ADR10 EXT ADR9 EXT ADR8 EXT ADR19 EXT WE GND VDD(+3.3V) EXT ADR18 EXT ADR17 EXT ADR7 EXT ADR6 EXT ADR5 EXT ADR4 EXT ADR3 EXT ADR2 EXT ADR1 GND VDD(+1.2V) NU PWRCON NU NU DVD-REMOTE NU GND VDD(+3.3V) DVD-SCLK DVD-CS MDQ2 MDQ13 MDQ5 MDQ10 MDQ4 MDQ11 MDQ3 MDQ12 MDQ7 MDQ8 MDQ6 MDQ9 23-L2 20-L2 19-L2 29-L2 26-L2 25-L2 24-L2 MA9 27-L2 22-L2 DATA9 DATA2 DATA10 EXT MEMORY DATA(0-15) SDRAM DATA(0-15) DATA3 DATA11 DATA4 DATA12 DATA5 DATA13 DATA6 DATA14 SDRAM ADDRESS(0-10) EXTERNAL MEMORY INTERFACE ECC DECODER INTERFACE STREAM INTERFACE DATA7 DATA15 DSP DECODER I/O PROCESSOR AUDIO INTERFACE DMA INST. ROM BCU 32BIT CPU DATA RAM INST. ROM UMAC DATA RAM INST. ROM AUDIO D/A CONVERTER DATA RAM DAC READ MEMORY INTERRUPT CONTROLLER DAC TIMER WATCH DOG TIMER VIDEO INTERFACE NTSC/PAL ENCODER CPU INTERFACE DAC DAC DAC CPU INTERFACE SERIAL GENERAL I/O DEBUG BCU INTERRUPT CONTROLLER WATCH DOG TIMER TIMER REMOTE CONTROL 32BIT CPU INST. CACHE DATA CACHE RF SIGNAL PROCESS CIRCUIT DVD/CD FORMATTER SDRAM DATA1 162 SDRAM DATA14 161 SDRAM DATA0 160 SDRAM DATA15 159 VDD(+1.2V) 158 GND 157 OSC-OUT 156 OSC-IN 155 VDD(+3.3V) 154 GND 153 152 151 NU 150 NU 149 NU 148 VDD(+3.3V) 147 146 GND 145 144 GND 143 VDD(+3.3V) 142 VDD(+3.3V) 141 GND 140 139 138 GND 137 COMP2 136 I-REF1 135 V-REF 134 COMP1 133 VDD(+3.3V) 132 131 130 129 VDD(+3.3V) 128 FOCUS DRIVE 127 TRACKING DRIVE 126 GND 125 FD-OFST 124 TD-OFST 123 SL-ADS 122 SP-ROT 121 120 119 118 117 116 115 114 113 112 111 110 V-REF(H) 109 MDQ1 MDQ14 MDQ0 MDQ15 R191 680 C191 15P 66-H1 65-K2 64-K2 CONTINUE DVD MAIN 1 LOAD-DISC SP-ROT SL-ADS R192 X101 1M 27MHz C192 22P R195 2.2K C197 100/6.3V C118 0.1 C196 0.1 CONTINUE DVD MAIN 3 DVD-SPDIF DVD-AUDIO(R) DVD-AUDIO-MUTE DVD-AUDIO(L) DVD-Y DVD-Pb DVD-Pr C195 0.1 C623 22P C125 1 R112 15K C120 1 37-G4 38-G4 R114 18K C329 150P C328 150P C122 0.1 R113 R128 39K 430 C135 4.7 C116 0.1 6-G4 7-G4 64-L4 65-L4 19-J4 20-J4 22-I4 23-I4 24-I4 25-I4 26-I4 27-I4 28-I4 29-I4 30-G2 31-H4 32-H4 CONTINUE DVD MAIN 3 DQM0 DQM1 DQM3 NWE NCAS NRAS NCSM BA0 BA1 MCK EXT-WE EXT-CE EXT-OE 50-G3 49-G3 48-G3 47-G3 R241 1K R242 1K 34-G4 33-G4 C212 120P L108 2.2uH C226 0.1 C225 0.1 C101 C102 100P 1000P G C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 820P 1000P 0.1 120P 1000P 100P 0.1 0.01 150P 0.1 1000P 47P 180P H C230 C222 0.018 0.1 C231 5600P C211 0.1 C237 0.1 C117 C119 820P 1000P 40-G4 42-G3 41-G4 C223 0.033 43-G3 44-G3 46-G3 45-G3 R291 10K 72-G2 R202 10K 70-G2 74-G2 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 79-G2 53-G3 78-G2 36-G4 66-L4 39-G4 35-G4 2 FADR16 FADR15 FADR14 FADR13 FADR12 FADR11 FADR10 FADR9 FADR8 FADR19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 VDD(+3.3V) GND FDQ1 FDQ9 FDQ2 FDQ10 CONTINUE DVD MAIN 1 EV+1.2V EV+3.3V(D) EV+3.3V(A) 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 V-REF-H5 V-REF-L5 IC101 MN2DS0018VP MICRO CONTROLLER 6-K2 7-K2 33-K1 34-K1 35-H1 36-H1 37-K2 38-K2 39-H1 40-J1 41-J1 42-J1 43-J1 44-J1 45-J1 46-J1 47-K1 48-K1 49-K1 50-K1 53-H1 EXT MEMORY DATA8 EXT MEMORY DATA0 EXT OE EXT CE EXT ADR0 VDD(+1.2V) GND SDRAM ADDRESS3 SDRAM ADDRESS4 SDRAM ADDRESS2 SDRAM ADDRESS5 VDD(+3.3V) GND SDRAM ADDRESS1 SDRAM ADDRESS6 SDRAM ADDRESS0 SDRAM ADDRESS7 SDRAM ADDRESS10 SDRAM ADDRESS8 SDRAM BA1 VDD(+3.3V) GND SDRAM ADDRESS9 SDRAM BA0 SDRAM DATA MASK3 NU SDRAM CS SDRAM RAS SDRAM CAS VDD(+1.2V) GND SDRAM MCK VDD(+3.3V) SDRAM MCK GND SDRAM WE SDRAM DATA MASK1 SDRAM DATA MASK0 SDRAM DATA7 SDRAM DATA8 SDRAM DATA6 SDRAM DATA9 VDD(+3.3V) GND SDRAM DATA5 SDRAM DATA10 SDRAM DATA4 SDRAM DATA11 SDRAM DATA3 SDRAM DATA12 VDD(+3.3V) GND SDRAM DATA2 SDRAM DATA13 CONTINUE DVD MAIN 1 FD-OFST TD-OFST VREFH VREF165 SLD STBY FOCUS DRIVE TRACKING DRIVE SPDL LPCO1 LPCO2 LPC VIN1RF VIN2RF VIN3RF VIN4RF VIN5 VIN6 VIN7 VIN8 CD/DVD R102 BEAD R101 56 NU DVD-SDATA NU NU NU NU DVD-DISC-OUT CD/DVD DVD-DISC-IN STBY LOAD-DISC SPDL SLD GND VDD(+3.3V) RESET NU NU NU NU NU NU DVD-P-ON NU NU NU NU GND VDD(+1.2V) VDD(+3.3V) PLFIL1 V-REF-H7 GND V-REF-L7 GND CCAPA CDATA VDD(+3.3V) NU NU 4 28-L2 32-L2 31-L2 MA3 MA4 MA2 MA5 FDQ0 FDQ8 MA1 MA6 MA0 MA7 MA10 MA8 FADR0 C239 0.1 C128 0.1 C130 0.1 C131 0.1 C136 330/6.3V C123 220/6.3V C134 220P C214 560P DVD MAIN CBA UNIT I J 11-16 K L FL11.8SCDV2 2- 11M2 M2 MA4 MA5 MA6 MA8 MA7 MA9 MDQ8 MDQ9 MDQ10 MDQ11 MDQ12 MDQ14 MDQ13 MDQ15 DVD Main 3 Schematic Diagram DVD MAIN CBA UNIT 3M2 R510 47K 4 C501 0.1 C502 180P C503 150P C504 220P C505 100P C506 0.1 C513 100P C514 680P 3 A4 VSS A3 VDD A5 A6 BA1 A7 A9 BA0 A8 NU UDQM CS CLK CKE CAS RAS UDQM NU A10/AP LDQM A1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 A2 9 A0 8 WE 7 VDD 6 DQ7 VSSQ DQ5 5 DQ6 DQ2 4 VDDQ DQ1 3 DQ4 VDQD 2 VSSQ DQ0 1 DQ3 VDD IC503 EM638165TSA-6G (SDRAM) L501 0 MA3 MA1 MA2 MA0 MA10 MDQ7 MDQ6 MDQ5 MDQ4 MDQ3 MDQ2 MDQ1 1- 5- 6- 7- 8- 9- 10M2 M2 M2 M2 M2 M2 M2 MDQ0 CONTINUE DVD MAIN 2 MA(0~10) MDQ(0~15) VSS DQ8 VDDQ DQ9 DQ10 VSSQ DQ11 VDDQ DQ12 DQ14 DQ13 VSSQ VSS DQ15 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 CONTINUE DVD MAIN 2 FDQ(0~15) FADR(0~19) IC103 MX29LV160DBTI-70G (FLASH ROM) CONTINUE DVD MAIN 1 EV+3.3V(D) 2 CONTINUE DVD MAIN 2 DQM0 DQM1 DQM3 NWE NCAS NRAS NCSM BA0 BA1 MCK EXT-WE EXT-CE EXT-OE 1-O3 2-O4 3-O4 5-O3 6-O3 7-O3 8-O3 9-O3 10-O3 11-O4 1 A15 A16 48 FADR14 2 A14 BYTE 47 FADR13 3 A13 VSS 46 FADR12 4 A12 DQ15/A-1 45 FADR11 5 A11 DQ7 44 FDQ7 DQ14 43 FDQ14 FDQ15 FADR10 6 A10 FADR9 7 A9 DQ6 42 FDQ6 FADR8 8 A8 DQ13 41 FDQ13 FADR19 CONTINUE DVD MAIN 1 RESET 1 FADR16 FADR15 DQ5 40 FDQ5 10 NU DQ12 39 FDQ12 11 WE DQ4 38 FDQ4 12 RP VCC 37 13 NU DQ11 36 9 A19 FDQ11 C561 0.1 14 NU DQ3 35 FDQ3 15 NU DQ10 34 FDQ10 L614 BEAD FADR18 16 A18 DQ2 33 FDQ2 L613 BEAD FADR17 17 A17 DQ9 32 FDQ9 FADR7 18 A7 DQ1 31 FDQ1 FADR6 19 A6 DQ8 30 FADR5 20 A5 DQ0 29 FADR4 21 A4 OE 28 FADR3 22 A3 VSS 27 FADR2 23 A2 CE 26 FADR1 24 A1 A0 25 L612 BEAD FDQ8 FDQ0 C612 0 R565 47 R567 47 C610 0.01 L618 0 CN601 4 5 6 7 8 9 10 11 12 13 14 15 16 TO MAIN CBA CN902 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF C608 22P R604 0.1 N C613 22P C620 22P FADR0 M CONTINUE DVD MAIN 2 DVD-SPDIF DVD-AUDIO(R) DVD-AUDIO-MUTE DVD-AUDIO(L) DVD-Y DVD-Pb DVD-Pr L104 BEAD R623 0 R611 2.2K R624 0 R621 0 R106 300 O P 11-17 Q C603 100P C604 100P C625 0.1 R604 0.1 R FL11.8SCDV3 Main CBA Top View J053 29 J003 GND CN301 GND 1 J059 DIF J060 28 DIF + 2 forA J086 29 GND CN302 J062 2 1 GND J043 29 28 CN303 P-ON-H1 AMP-R AMP-L J017 J033 J034 KEY-IN1 LED-R J159 SP-GND 1 2 J242 29 C831 J083 CN702 08 J030 GND D9 Q801 C910 2 1 C806 D909 J029 P-ON+9V C653 J247 SP-GND C654 D665 8 D805 J020 GND J009 D804 D809 AMP-R-HP J021 C813 D AMP-R-HP CN102 1 J025 GND J019 RIPPLE REJECTION J007 AMP-L-HP J008 SP-GND J084 J181 GND J072 A-Protect IC801 D808 D414 11-18 Q172 R838 D907 GND R675 J230 M+10V SW D666 Q641 GND J077 R806 R807 J065 GND R638 R635 GND J073 GND D905 R676 J105 SP+14V 31V R658 C645 J032 J028 SP-GND Q631 D656 P-ON+9V R906 C812 C P-ON+9V J026 J027 GND GND GND J080 C838 D646 J180 C608 GND J022 C917 D645 R637 J038 D413 J081 J074 GND D903 J104 J103 D902 C918 C916 J047 GND GND IC601 J102 R609 R612 TRANS-D R932 C919 R634 D644 D648 D407 28 C928 R933 R927 C921 D906 R919 Q905 D647 Q602 D412 25 CN901 GND J185 Q904 R929 J107 GND R928 R926 R925 GND J042 R922 R924 J052 C604 Q601 R611 B 26 2 Q903 IC901 R923 P-ON SW C606 D609 C607 D607 GND D606 GND J183 P-ON+9V JS101 DVD-LED GND 13 CN902 1 C643 R608 R606 R604 01 FH6 R Q633 S-SW D415 GND J108 DVD-LED JS103 GND R913 C640 D610 C692 R603 02 R607 C605 J082 J044 M+9V GND J075 R905 12 2 GND J046 J125 P-ON+5V P-ON+9V D901 PCB STUD D612 R912 HOT R605 COLD A C904 D401 D643 BC601 610 P-ON-H2 1 D605 D608 DVD-MAIN-PWR J124 Q907 R930 RISK OF FIREREPLACE FUSE AS MARKED TM601 AC601 TM602 J036 J050 J045 D640 J237 31V D638 D601 31V FET-G LCD+13V J070 J079 DVD-A-POW T601 J100 GND Q171 GND J195 D904 R904 L901 D631 D636 C638 C6 / BLACK J035 Q902 J GND J051 J126 Q906 4 R91 J188 31V FH6 F601 4A/125V R601 83 J236 31V D604 TOOL NO. 1 2 3 4 5 6 7 8 9 10 CN862A J192 D641 CN1002 R6 Q401 R602 C601 C819 PROTECT1 R679 R917 R172 Q901 Q634 D650 R826 R652 R682 A3 GND J061 A-MUTE GND R6 C7A3 D639 C603 1 J054 D651 D416 P-ON+5V 91 / WHITE RCV-IN J055 D649 R651 A01NMPW E234498 IC631 C639 R689 COLD CN872 LED1 ALL+3.3V J037 84 R656 Q643 D637 J189 HOT ALL+3.3V C647 R650 R688 D632 D402 C401 C631 R631 SA601 J040 J069 INV+31V for ALL+3.3V J111 J120 ALL+3.3V R649 C632 GND D603 D611 J039 J231 P-ON-H2 C636 D602 GND J048 D301 DVD-Y Q637 GND J232 P-ON-H2 J066 J049 C650 DVD-Pb D642 C648 for TU+5V D302 SDA IF-AGC D417 P-ON+3.3V PROTECT2 R661 SCL J010 J011 J149 J128 D659 J056 D652 C633 L601 28 J106 GND J071 J068 LED1 L301 D657 GND GND J136 D670 ALL+3.3V J140 GND J138 J135 TU301 TU302 R680 GND J141 P-ON+5V J148 P-ON-H2 for TU+5V 31V TU+5.0V J101 J137 GND J063 GND D411 LCD+13V TUNER A S J041 LCD+13V GND J234 RESET J139 INV+31V C641 COLD HOT J246 J151 J187 3.5Vfor1.8V R240 6.7Vfor1.0V P-ON-H1 J160 J239 INV+31V 59 R6 C306 GND ALL+3.3V J018 D653 P-ON+3.3V J067 J109 P-ON+5.0V GND GND J119 J150 J152 J153 RCV-IN R411 J127 GND D409 J205 Q402 GND R406 GND R698 J224 D410 PROTECT2 J147 J133 for P-ON+5V J123 D668 D1037 D303 J191 GND Q636 J193 6.7Vfor5.0V D633 2 Q203 R662 J114 D654 J002 D208 J142 J134 P-ON-H2 PROTECT C1014 C303 J161 R663 J1015 31V GND J245 J001 D408 D209 J143 5.5Vfor3.3V D655 3 R215 D203 Q202 J144 5.5Vfor3.3V 5.5Vfor3.3V BA01N4F0101 4 C1011 R699 D406 J158 VGH+24.5V J176 VCOM-PWM Q209 5.5Vfor3.3V J130 R690 R1117 C655 P-ON+3.3V C649 Q635 J129 J113 J122 J157 GND R664 R1034 15V R655 D667 C204 GND R1118 R1097 R1033 Q638 J1001 Q640 J165 GND J146 J145 D1019 VT+32V R671 J177 GND J154 GND GND GND R1096 D661 R670 D202 R218 R20 1 Q206 Q1011 GND GND J118 J076 GND 15V J078 R1026 J132 J131 P-ON-H2 5V-S JS307 D403 J194 Q639 D662 C217 LCD+13V J229 Q201 R222 R1031 GND J116 JS306 J085 J240 J162 J170 LCD SW R665 D1046 J1005 GND 32V-S JS308 5V-A forS J197 Q1020 32V-A JS305 D404 GND R217 J164 LCD+13V J163 P-ON+5.0V J190 Q205 J166 NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. 6.7Vfor1.0V J058 TU+5V R219 D204 D660 R235 D205 R216 R1047 C661 R239 C205 R207 R208 J186 GND Q1012 D210 Q1002 GND J1004 GND C209 ADJ SW J200 Q1024 R1108 JS1005 Q1004 J241 GND D201 D207 R223 J227 J1003 Q210 J057 J064 D206 J1006 R1100 C1023 LCD+13V C201 VT+32V 2IN+ D1030 C1019 J1018 GND J172 R672 R1030 Q208 R229 C207 J209 R228 J178 VGL-7.1V C1027 J1017 C1002 D1021 J171 R226 Q207 J174 VCOM J175 GND REF+5V DTC FB D1031 J203 C652 R1013 PROTECT3 VGL-7.1V LCD+13V Q1008 D1040 J215 REG C1059 P-ON+3.3V J117 R1102 D1039 D1029 R1032 D C1012 D1047 JS1011 R1092 JS1007 C1053 JS1006 Q1006 J168 BL-SW J179 J169 J228 R1008 T1002 C1006 D1018 R1003 D1028 D1002 R1049 J208 DRIVE Q1018 R1065 R1101 Q1017 G R1007 D1003 R1103 JS1013 G 4 H.V CAUTION D405 D1045 JS1004 IC Vcc R1006 R1010 JS1012 R1091 Q1023 R1095 C1031 GND D1025 Q1001 CN1001 C1015 JS1010 D R1094 D1015 D1013 R1093 C1007 D1008 R1017 D1012 D1010 C1008 C1001 J204 J214 BL-ON 15V R1074 C1005 C1058 D1007 D1014 D1026 Q1007 D1009 C1 J210 2IN+ R1066 C1033 GND R1002 R1001 J221 D1022 D1027 J213 J222 BL-ON 15V D1023 J211 R1029 GND Q1016 D1020 D1035 D1036 D1005 J225 J220 -INB J201 GND D1006 D1011 Q1015 R1044 C1009 GND GND Q1009 J223 R1012 D1001 D1004 R1014 R1111 C1013 Q1003 D1038 GND J199 D1024 J173 GND J167 BL-ADJ D1041 J216 -INA C1010 CN201 D1033 INV+31V J1002 Q1010 Q1014 4A/125V GND J219 D1034 5 C1055 Q1019 Q1025 GND J226 R1113 D1016 Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. VGH+24.5V BL-ON+15V CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. C805 E BA01N4F01014 Main CBA Bottom View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Q1019 R1084 C1040 C1055 D1034 R1058 C1044 R1059 R1056 R1114 R1116 C218 R1057 C1057 R1115 R1113 BL-ON+15V R1089 D1005 R1015 D1036 D1035 R1112 C1013 R1016 GND Q1009 GND R1111 J225 C1042 D1004 D1026 D1014 D1007 D1010 D1012 C1007 R1094 D1008 R1017 R1093 CN1001 C1015 Q1005 C1003 R1023 R1022 R1081 R1018 R1082 R1083 R1086 C1039 R1087 D1042 D1032 C1032 R1060 R1061 C1019 4 JS1011 R1032 D C1012 D1047 H.V CAUTION T1002 Q1022 R1024 R673 C1006 R1035 C1059 R1013 Q640 C651 R655 R674 R1039 C1002 D1021 C1038 C1018 R671 J122 R1014 D1001 R1012 J223 R1019 D1022 Q1015 C1001 JS1010 D D1003 J1018 GND D1046 R667 C652 J245 GND J1015 31V C1011 C632 84 R1062 C1014 CN1002 C1021 D641 D401 Q401 R631 D631 D636 D603 J236 31V D638 C638 31V J237 IC901 Q903 D601 R902 R901 C901 R928 J042 C643 GND D906 R920 D612 C644 91 C6 C692 D610 J047 GND C916 R676 D902 C918 R634 D644 C646 C919 C920 R932 D666 J230 M+10V SW FH6 01 C607 R601 D607 D608 R611 IC601 D609 Q602 TRANS-D R609 R612 J102 R641 GND R681 R653 R654 Q601 R640 C604 SA601 R604 BC601 C606 GND J052 C820 R647 D606 J100 FH6 02 FET-G R605 R606 R608 J103 CN872 1 AC601 C801 CN862A R61 0 J180 C608 R636 C645 R646 R658 R638 J065 GND R635 R639 J072 A-Protect R409 GND J181 GND J084 C819 Q631 D656 R642 R644 R643 R645 AMP-R-HP J021 D809 C807 R804 R816 C813 C811 R818 C808 R815 R805 J025 D414 C601 R603 P-ON SW R807 R806 GND J077 C654 R819 R817 R808 J104 Q641 J105 SP+14V 31V C653 R675 R842 C833 D646 D611 C603 R607 C605 D648 2 D643 T601 Q633 L601 31V J189 J188 31V R930 R637 D602 D604 R401 C640 GND R913 J242 R602 D647 C812 J002 R1064 C636 D605 D645 R1051 D632 R404 C633 83 L901 R942 R941 R921 C902 R927 GND C402 J192 GND R933 C904 C924 C922 C928 R936 R929 D1037 C401 D402 R402 R403 C631 D637 R689 R912 R925 3 PROTECT R1050 R1009 R688 R686 R685 D668 IC631 GND J195 C923 R931 1 D903 R820 RIPPLE REJECTION J007 AMP-L-HP SP-GND J008 C1041 R1088 D1025 Q1001 C1005 C1036 C1058 D1030 C1026 R1026 R666 Q638 J1001 15V R6 R682 Q901 R935 C926 D901 R910 R911 C912 C921 C914 J107 GND D907 C910 C821 Q801 R809 J009 E R906 C1008 R1091 D633 4 R923 Q904 D1011 J001 D640 D665 D805 1 GND D804 08 CN902 Q905 J219 R1001 J221 C1048 R1021 Q1008 D1039 R1011 C1049 R1025 C1052 R1033 R1097 R670 D639 2 13 D905 R919 D909 C810 R803 D9 J030 GND 12 R922 D1015 D1013 D1002 D654 R6 R91 R924 C917 J019 CN102 GND C802 C809 C816 R810 C817 R814 R813 J029 P-ON+9V IC801 D808 J020 J073 J080 J074 GND GND 8 AMP-R-HP BC902 R943 C927 R940 C925 R926 GND J185 2 WF13 PIN 1 OF CN902 J028 SP-GND IC902 R811 C832 C830 R834 C828 C806 1 J247 SP-GND WF12 PIN 3 OF CN902 C907 C203 CN901 J081 C1033 R1092 C641 R918 C906 GND J083 BC801 R838 R173 25 P-ON+9V GND CN702 C818 WF11 PIN 5 OF CN902 R652 C929 R908 R903 C903 C915 C911 C913 C908 C909 C831 R171 2 G D662 C639 8 R905 26 GND C838 5 Q907 JS1012 J1017 J113 Q643 1 J022 J032 R907 J075 P-ON+9V R909 C826 Q172 8 Q902 R648 C829 R826 R175 R174 P-ON+9V J026 J027 GND 4 J079 DVD-A-POW J183 P-ON+9V D413 5 1 Q906 BC901 J045 DVD-LED JS103 R649 R916 R414 J037 R830 R823 R172 Q171 JS101 DVD-LED 28 29 WF9 PIN 11 OF CN902 WF8 PIN 9 OF CN902 IC803 1 R904 D1009 J215 REG VT+32V C1004 D1006 D1027 D655 D904 P-ON+5V J108 GND D412 J038 GND J070 GND D407 4 J050 J125 M+9V J044 GND R917 J124 P-ON-H2 D415 WF10 PIN 13 OF CN902 DVD-MAIN-PWR P-ON+5V J051 J126 LCD+13V J046 R821 C825 J082 GND GND R836 C827 R678 GND S-SW GND J036 R1103 Q1017 C1017 R1102 R1101 C1034 R1068 Q1010 R1028 D1018 R668 R669 J1005 GND D667 C656 R915 R413 R837 R679 Q634 D650 R1020 R1072 C1037 R1071 R1073 GND Q1016 J213 Q1018 R1067 J208 DRIVE R1049 R1027 C1023 J227 R1096 R1118 R1034 31V R650 R651 D1020 R1104 C1047 R1029 BL-ON 15V R1040 R1066 JS1004 IC Vcc R1036 R1041 C1054 D1031 JS1005 R1100 J1004 GND D661 J123 R656 D649 D651 D416 GND C1043 J226 C1050 R1090 R1070 C1025 R1038 C1053 FB JS1006 DTC JS1007 R1108 Q1004 GND J241 J078 C661 D652 GND J055 J061 A-MUTE C1031 R1037 R1045 R1043 R1046 C1028 R1055 R1054 C1056 R1109 R1095 C1045 REF+5V 15V GND D660 59 R6 J120 R1030 2IN+ D1028 R1117 C655 J114 6.7Vfor5.0V INV+31V D1040 J203 J1003 5 Q1003 C1009 GND R1002 Q639 D1019 J139 INV+31V D1029 C1010 J201 GND J222 R1007 R1008 D1016 Q1014 D1023 R1010 G JS1013 D670 C905 J232 Q1006 GND Q1020 R690 2 1 INV+31V C1016 R1004 J076 J136 C1035 R1069 R1106 Q1012 R1099 GND GND R1003 D1024 -INB J220 Q1007 R1006 R1047 R664 J135 GND J214 BL-ON 15V R1074 R1065 J116 P-ON-H2 R665 D642 R662 J049 DVD-Pb J149 J039 J040 J054 J041 J034 J035 J033 J017 J069 J053 ALL+3.3V J118 J130 J117 5.5Vfor3.3V R663 GND J143 GND J210 2IN+ R672 VGH+24.5V 5.5Vfor3.3V 1 16 9 Q1025 -INA J216 IC1002 R1044 8 J204 Q1011 Q206 J154 GND GND J165 J186 GND J129 J134 P-ON-H2 for ALL+3.3V J111 ALL+3.3V C647 J131 5.5Vfor3.3V J148 P-ON-H2 for TU+5V Q637 J231 P-ON-H2 GND J144 J239 C650 J048 DVD-Y J132 J145 J234 RESET for TU+5V R1031 C1020 R221 C206 1 R20 R202 C304 P-ON+3.3V RCV-IN ALL+3.3V LED1 PROTECT1 J159 AMP-R SP-GND AMP-L CN303 P-ON-H1 KEY-IN1 LED-R 29 D659 R661 C648 GND GND J133 for P-ON+5V GND J199 IC1001 C1 J211 VT+32V 5.5Vfor3.3V J138 J200 R222 R220 C202 R203 R218 28 J128 Q1002 J194 GND PROTECT2 R1005 Q201 R205 R223 J163 C1027 J209 J1006 R208 J166 D1038 C1024 D202 R204 C204 J157 INV+31V D203 Q202 R633 GND J146 J193 GND R660 GND J140 GND R1052 R1042 R1048 C213 C212 C210 C211 R227 C214 C207 J172 D207 GND D1041 D1045 R1053 J177 GND R215 J164 C221 C215 C209 Q209 R206 D209 LCD+13V GND D1033 ADJ SW R1110 R1107 Q1024 R225 R224 R237 R238 J229 R234 D408 R214 R212 D403 Q636 P-ON+5V C219 C220 R210 LCD+13V C216 C217 R230 R232 R231 R233 J224 VGL-7.1V D204 J1002 Q1023 R1105 R209 D406 J158 VGH+24.5V J176 VCOM-PWM R699 R698 J170 LCD SW R632 J066 P-ON-H2 2 IF-AGC R217 J137 J141 ALL+3.3V R219 C649 Q635 J142 GND J011 GND J197 J101 J228 J171 LCD+13V C201 Q205 R405 J160 J179 J169 D210 R207 J161 LCD+13V D657 D411 TU301 TU302 R680 R677 1 GND J043 J010 SDA D417 WF1 PIN 4 OF CN302 R240 LCD+13V VCOM J174 J175 R216 R412 R303 R302 GND J056 SCL D301 R211 J147 8 C205 D205 D208 R213 C301 L301 C685 C309 R313 J162 P-ON-H1 R176 J062 CN302 TUNER S A D302 3.5Vfor1.8V JS303 C314 JS301 JS804 JS802 29 PROTECT2 J168 D201 Q203 GND J191 J167 BL-SW J178 D206 R239 GND BL-ADJ PROTECT3 VGL-7.1V LCD+13V R229 J190 CN201 J173 GND P-ON+3.3V IC201 5 Q208 R235 D303 TU+5.0V WF3 PIN 6 OF CN302 R228 Q210 C303 C315 JS805 JS801 forA J086 J059 DIF J060 DIF + 28 GND J063 JS803 J153 6.7Vfor1.0V J187 J151 J240 P-ON+3.3V 1 4 Q207 D410 J152 GND GND J150 J119 J067 J109 forS 2 WF2 PIN 8 OF CN302 R406 GND P-ON+3.3V J246 J085 D405 R226 J064 5V-S JS307 D404 1 WF7 PIN 13 OF CN302 P-ON+5.0V RCV-IN BC301 C306 J018 D653 ALL+3.3V J068 LED1 C302 TU+5V JS306 GND R407 J205 R408 GND Q402 D409 R411 J127 GND J106 GND R304 R307 R306 R305 JS304 L303 L302 32V-A JS305 5V-A C311 C310 GND CN301 32V-S JS308 GND C305 J058 P-ON+5.0V J071 J003 GND C681 C682 29 WF5 PIN 17 OF CN302 WF4 PIN 15 OF CN302 C683 C684 28 WF6 PIN 19 OF CN302 CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V J057 6.7Vfor1.0V Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. C805 D C B 11-19 A BA01N4F01014 Jack & Function CBA Top View Function CBA Not Used POW. CL862 ST.BY D103 C7A3 A3 b DVD D950 /GREEN P PATTERN SW955 /RED P /ORANGE CN862B D952 C108 J901 RCV-IN SW954 AGING R951 D104 R954 C951 D951 C109 R116 D105 CN101B CN101A R106 R950 RS101 B CL861 b BA94N0F0102 2 b P LC7 19/22W BASE Not Used CN861B Not Used C103 SW109 POWER SW951 PLAY STOP SW952 SW953 EJECT SW108 CH.UP SW107 CH.DOWN MENU SW106 VOL.UP SW105 SW104 VOL.DOWN CN101 J803 GND JACK CBA J810 P-ON+9V JK751 R757 JK841 R758 JK711 JK741 JK721 JK752 R774 R775 P-ON+9V J807 COM-Y J809 2 1 BA94N0F0102 JK731 J818 SPDIF R756 Q841 J813 PC-AUDIO-L R763 28 29 J822 GND V-R J812 V-R BC771 R782 D706 R851 C7A3 A3 L852 AMP-R-SP J805 J804 HP-GND A J806 1 BA94N0F0102 2 J808 HP-GND R852 AMP-L-HP C771 L851 CN871 J816 GND D709 4 2 J802 SP-L-GND J821 L853 CN861A J801 Q722 L854 Q773 R788 D705 1 J820 GND JK851 R789 Q771 AMP-L-SP TOOL NO. 1 2 3 4 5 6 7 8 9 10 JK754 JK733 2 J815 PC AUDIO-L J817 Q774 JK753 JK742 JK722 J814 GND JK732 J811 SEL-R CN701 J819 11-20 BA94N0F01022 Jack & Function CBA Bottom View Not Used Function CBA Not Used C105 C110 R712 R711 R753 R734 R844 R718 JK721 R792 R717 J813 C757 PC-AUDIO-L JK741 C841 C731 R 8 4 3R 7 3 1 C845 R763 JK722 JK754 R755 V-R J812 R793 R732 R733 JK742 CN701 J811 SEL-R R747 R721 V-R C743 JS701 R741 C732 JK732 R794 J819 R787 C773 R735C735 C723 R727 R764 GND J814 R754 C736 R742 GND J822 D704 C724 R722 R786 JK733 R736 R783 R797 R777 IC771 R773 Q771 R796 J820 GND R779 C775 R772 Q773 CN861A 9 Q722 8 D710 C771 R778 J816 GND L853 L851 R776 C776 J821 J801 AMP-L-SP J802 SP-L-GND R852 C861 CN871 L854 16 1 D703 Q774 C733 D701 C744 R784 R748 C772 J808 HP-GND J806 HP-GND C852 AMP-L-HP C851 R782 D705 R788 R780 D702 J817 D706 JK851 D707 R789 D708R791 R790 J815 PC AUDIO-L BC771 R781 2 R728 11-21 CN101A CN101 R774 R785 C753 R795 R775 C704 C703 R851 CN101B C734 R848 BA94N0F0102 R752 J809 C756 JK711 R751 JK752 J901 RCV-IN JK841 C752 J818 SPDIF JK731 JK751 R757 R758 COM-Y J807 C755 Q841 R756 C751 BC841 C842 R847 R845 R846 J810 C843 P-ON+9V P-ON+9V VOL.UP SW105 C754 JK753 R111 J803 GND SW108 CH.UP SW107 CH.DOWN MENU SW106 R112 JACK CBA C758 SW104 VOL.DOWN R956 D105 D952 D951 C109 R115 R114 SW951 PLAY STOP SW952 R118 R113 C951 R955 R953 R954 D104 C103 SW109 POWER C950 R950 R106 R951 R952 L852 AMP-R-SP J805 J804 CL861 CL862 P C111 PATTERN SW955 DVD D950 ST.BY D103 SW953 EJECT CN861B CN862B POW. C104 R116 R107 SW954 AGING C106 R108 D709 C107 R109 C108 D101 R S 1 0 1R 1 1 0 P b Not Used BA94N0F01022 b P b WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) WF1 Pin 4 of CN302 CVBS WF2 0.2V WF6 20µs 0.2V 20µs AUDIO 0.2V 20µs Pin 19 of CN302 VIDEO-Pr WF7 0.2V Pin 17 of CN302 VIDEO-Pb Pin 6 of CN302 S-VIDEO-C WF4 20µs Pin 8 of CN302 S-VIDEO-Y WF3 WF5 0.2V 20µs Pin 13 of CN302 0.1V 0.5ms Pin 15 of CN302 VIDEO-Y 0.2V 20µs 12-1 LC9NWF1 WF8 ~ WF13 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) DVD Video (Play MODE) WF8 DVD-Y WF9 DVD-Pb WF10 DVD-Pr Pin 9 of CN902 0.5V WF11 DVD-AUDIO(L) 20µs Pin 11 of CN902 0.5V WF12 WF13 20µs 0.5ms 0.5V 0.5ms Pin 1 of CN902 DVD-SPDIF 12-2 0.5V Pin 3 of CN902 DVD-AUDIO(R) 20µs Pin 13 of CN902 0.5V Pin 5 of CN902 1V 0.1µs FL11.8WF2 CN302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CL3702 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 CL3701 P-ON-H2 GND GND GND PROTECT3 AMP(L)-OUT GND AMP(R)-OUT P-ON-H1 P-ON+3V PROTECT1 GND P-ON+5V/LED-R P-ON+5V PROTECT2 P-ON+7V GND GND P-ON+3.3V P-ON+3.3V AL+3.3V AL+3.3V GND GND REMOTE BACKLIGHT-SW LED1 BACKLIGHT-ADJ VCOM-PWM CN3006 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN3002 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CL4001 GND KEY-IN2 DVD-LED P-ON-H3(NU) DVD-MAIN-PWR DVD-P-ON DVD-REMOTE DVD-SDATA DVD-DISC-IN GND DVD-CS GND DVD-SCLK GND DVD-DISC-OUT LED-CONT GND DVD-Pr GND DVD-Pb GND DVD-Y GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF GND CN303 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 TO DVD MAIN CBA UNIT CN401 (CL901) GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED CN102 1 2 3 4 5 6 7 8 CN901 AL+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON SP(R) SP-GND CN872 1 2 MAIN CBA TO WIRING 2/2 DIAGRAM FUNCTION CBA CN101B 1 2 3 4 5 6 7 8 CL862 TO WIRING 2/2 DIAGRAM SP862 SPEAKER R-CH TUNER UNIT 13-1 13 12 11 10 9 TO 8 DVD MAIN CBA UNIT 7 6 CN601 5 (CL902) 4 3 2 1 AC601 AC CORD DIGITAL MAIN CBA UNIT CL201 GND PANEL+13V PANEL+13V PANEL+24.5V GND PANEL+3.3V PANEL+3.3V PANEL-7.1V GND VCOM GND CN702 1 2 3 4 5 6 7 CN902 8 DVD-Pr 9 GND 10 DVD-Pb 11 GND 12 DVD-Y 13 GND 14 GND 15 GND DVD-AUDIO(L) 16 17 DVD-AUDIO-MUTE 18 DVD-AUDIO(R) 19 GND 20 DVD-SPDIF 21 22 23 24 25 26 27 28 29 CN871 1 2 JACK CBA CL701 CN701 SP(R) 1 SP(R) 2 HEADPHONE(R) 3 HEADPHONE(R) 4 GND 5 6 GND 7 GND 8 GND HEADPHONE(L) 9 HEADPHONE(L) 10 11 GND 12 GND 13 AUDIO(L) 14 P-ON+9V 15 AUDIO(R) COM-VIDEO-Pr-IN 16 17 GND COM-VIDEO-Pb-IN 18 19 S-VIDEO-SW COM-VIDEO-Y-IN 20 21 GND 22 INPUT0 23 SPDIF 24 INPUT1 25 GND S-VIDEO-Y-IN 26 27 VIDEO-IN S-VIDEO-C-IN 28 29 GND LCD MODULE ASSEMBLY BACK LIGHT CN1002 1 2 CN201 1 2 3 4 5 6 7 8 9 10 11 BACK LIGHT CN1001 1 2 SP(L) SP-GND S-VIDEO -IN DIGITAL AUDIO-OUT (COAXIAL) AUDIO(R) -IN AUDIO(L) -IN VIDEO-IN HDMIAUDIO(R)-IN HDMIAUDIO(L)-IN COMPONENTAUDIO(R)-IN COMPONENTAUDIO(L)-IN COMPONENT -Pr-IN COMPONENT -Pb-IN CL861 CN3005 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 COMPONENT -Y-IN CL3902 STV XAO OE1 CPV POL TP GND LLV5(-) LLV5(+) LLV4(-) LLV4(+) LLV3(-) LLV3(+) GND LLVCLK(-) LLVCLK(+) GND LLV2(-) LLN2(+) LLV1(-) LLV1(+) LLV0(-) LLV0(+) GND SP861 SPEAKER L-CH HDMICONNECTOR-2 HDMICONNECTOR-1 PC-RGB-IN USB JACK Wiring 1/2 Diagram WIRING DIAGRAM FL11.8WI1 PICKUP DETECTOR 7 9 11 2 3 6 5 4 TS DRIVE CBA LOAD-DISC 1 2 3 4 SENSOR CBA LED-POWER DVD-DISC-OUT DVD-DISC-IN GND DISC-IN 1 2 3 4 DISC-OUT CN5001 CN5001 is soldered directly to the PCB. CN801 AL+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON CN401 (CL901) TO MAIN CBA CN901 TO WIRING 1/2 DIAGRAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 FS 1 2 3 4 5 6 SLED MOTOR M SP(+) SP(-) GND SL(-) SL(+) LOAD-DISC SPINDLE MOTOR M CN201 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN301 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF DVD-ON+5V CD/DVD D A C B NU VREF NU GND CD-LD GND(LD) DVD-LD PD-MONI GND(DVD-PD) GND(CD-PD) TS(-) FS(-) FS(+) TS(+) DVD MAIN CBA UNIT 4 5 6 7 8 9 10 11 12 13 14 15 16 CN601 (CL902) TO MAIN CBA CN902 DVD MECHANISM Wiring 2/2 Diagram 13-2 FL11.8WI2 SYSTEM CONTROL TIMING CHARTS Disc In ~ Play/Play ~ Disc Out Disc In Disc IN (TL221) Disc Rotation Play Disc Stop Disc Out 3.3V 0V Sled Drive (TP303) 1.65V Disc Drive (TP301) 1.65V Focus Drive (TP304) 1.65V 0V 0V 0V Tracking Drive (TP302) 1.65V 0V 14-1 TVDVDN_TI LEAD IDENTIFICATIONS KTA1267-GR-AT/P E C B 2SA950-Y(TE2 F T) 2SA1020-Y(TE6 F M) 2SC2120-Y(TE2 F T) 2SC2655-Y(TE6 F M) 2SD400(F) KTC3199-GR-AT/P E C B LD1117V 8 7 6 5 1: 4 2: 3 3: 4: 1 2 1: Vin 2: Vo 3: GND 1 2 3 2SC4881F GD S B C E NJM4558M(TE1) KIA358F-EL LTV817MCF TL3472CDR TK5A50D 8 5 1 4 A K E C 1 2 3 4 TC4052BF(ELNF) TL494CDR 9 16 8 1 TDA1517P AP1117TG-U 10 18 1: GND 2: Vout 3: Vin 9 1 1 2 3 TPC8214-H 8 5 1 4 Note: A: Anode K: Cathode E: Emitter C: Collector B: Base R: Reference S: Source G: Gate D: Drain 15-1 FL11.8LE EXPLODED VIEWS Cabinet [LD190SS2, 19MD301B/F7] Digital Main CBA Unit A1 L12 B1 L4 CL3701 CL3702 L12 CL4001 A10 L3 B7 B44 B7 A24 CL3902 CL101 A42 B9 Jack CBA CL201 A5 L4 L11 L1 L3 A9 SP861 L2 L2 L3 L1 Function CBA A3 A15 B3 B10 B8 SP862 CL862 B3 CL701 L3 CL861 L8 B8 L9 L3 L8 A4 B2 LCD1 B13 L1 L1 Main CBA S5 L3 L4 L3 B11 L5 L13 B14 L1 A8 AC601 L1 CL901 L5 L9 DVD Main CBA Unit A6 S5 CL902 See Electrical Parts List for parts with this mark. L1 Stand Assembly 1B1 L6 L17 16-1 FL11.8-A_CEX Cabinet [LD190EM2, 19MD311B/F7] Digital Main CBA Unit A1 L12 B1 L4 CL3701 CL3702 L12 CL4001 A10 L3 B7 B44 B7 A24 B9 CL3902 Jack CBA CL201 L4 L11 A42 L1 L3 A9 B28 SP861 L2 L2 L3 L1 SP862 B3 CL701 L3 A13 A15 B3 B10 CL861 B8 CL862 A11 B8 L8 CL101 L9 L3 L8 A4 B2 LCD1 B13 L1 L1 Function CBA L1 Main CBA S5 L3 L4 L3 B11 L5 L13 B14 L1 A8 AC601 L1 CL901 L5 L9 DVD Main CBA Unit A6 S5 CL902 See Electrical Parts List for parts with this mark. L1 Stand Assembly 1B1 L6 L17 16-2 FL11.8-A_CEX Packing L17 X4 X3 X6 X2 Stand Assembly X1 S6 Fixlon Tape S5 S2 S4 X10 Tape Packing Tape S5 S3 FR ON S3 T FR ON T Packing Tape Some Ref. Numbers are not in sequence. S1 16-3 FL11.8PEX PARTS LIST [LD190SS2 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. Ref. No. Description SP861 SPEAKER S0307F04 SP862 SPEAKER S0307F04 Part No. DS16070XQ001 DS16070XQ001 PACKING NOTE: Parts that are not assigned part numbers (---------) are not available. S1 CARTON A1DN2UH 1EM434618 S2 STYROFORM TOP A94N0UH 1EM023965 S3 STYROFORM BOTTOM A94N0UH 1EM023966 S4 SET BAG A81N0UH 1EM323958 S5 SERIAL NO. LABEL A01PBUH ---------- S6 STAND BAG A81N0UH 1EM425888 ACCESSORIES Ref. No. Description STAND ASSEMBLY A9DN1UH Part No. X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A 1ESA23635 X2# OWNERS MANUAL A1DN2UH 1EMN27585 A1 FRONT CABINET A94N1UH 1EM123293 X3 REMOTE CONTROL NF033UD NF033UD A3 CONTROL PLATE A94N0UH 1EM325657 X4 DRY BATTERY(SUNRISE) R6SSE/2S XB0M451MS002 A4 REAR CABINET A9DN0UH 1EM124315 X6 QUICK START GUIDE A1DN2UH 1EMN27586 A5 DECORATION PLATE A1DN2UH 1EM225964 X10 REGISTRATION CARD (SYLVANIA) A017DUH 1EMN27080 A6# RATING LABEL A1DN2UH ---------- A8 JACK LABEL A9DN0UH 1EM430877 A9 JACK HOLDER(A) A94N0UH 1EM222783 A10 JACK HOLDER(D) A94N0UH 1EM222784 A15 CAUTION LABEL A1DF2UH ---------- A24 ENERGY STAR LABEL ---------- A42 ENERGY GUIDE LABEL ---------- 1B1 DVD MECHA SLOT E7 N7XT3KVM N7XT3KVM B1 SHIELD BOX A17F4UH 1EM225624 B2 STAND HOLDER A94N0UH 1EM325619 B3 WALL MOUNT BRACKET A84N0UH 1EM323797 B7 GASKET A8AF0UH 1EM425861 B8 SPEAKER HOLDER A94N0UH 1EM325677 B9 LASER CAUTION LABEL ---------- B10 FELT A94F0UH 1EM428797 B11 DVD HOLDER A94N0UH 1EM123213 B44 THERMAL SHEET TMS-14-20 12X12 XK10000X4011 CL201 WIRE ASSEMBLY 11PIN FFC 11PIN 75MM WX1A94N0-105 CL701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 CL861 WIRE ASSEMBLY 2PIN 2PIN/75MM/AWG 26 WX1A01N0-002 CL862 WIRE ASSEMBLY 2PIN 2PIN/75MM/AWG 26 WX1A01N0-002 CL901 WIRE ASSEMBLY 26PIN FFC 26PIN 240MM WX1A94N0-112 CL902 WIRE ASSEMBLY 13PIN FFC 13PIN 60MM WX1A94N0-103 CL3701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 CL3702 WIRE ASSEMBLY 29PIN FFC 29PIN 70MM WX1A94F0-111 CL3902 WIRE ASSEMBLY 24PIN FFC 24PIN 65MM WX1A94N0-106 CL4001 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 L1 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100 L2 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 L3 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 L4 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080 L5 SCREW TAP TIGHT M3X10 BIND HEAD+BLK NI GBHS3100 L6 SCREW P-TIGHT 3X12 WASHER HEAD+ GCJP3120 L8 ASSEMBLED SCREW M3X10 1EM420633A L9 DOUBLE SEMS SCREW M4X10 + BLK FPH34100 L11 HEX SCREW #4-40 7MM 1EM430139 L12 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B L17 STAND SCREW KIT A1DN2UH 1ESA27868 LCD1 LCD MODULE 18.5INCH WIDE CMO 18.5INCH UJ19MXA WXGA 2011/04/22 17-1 A1DN2CA.fm Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. Ref. No. Description Part No. C603 CAP ELECTROLYTIC 270µF/200V CEA271DYG005 C604 POLYESTER FILM CAP. (PB FREE) 0.039µF/ 100V J CA2A393DT018 C605 POLYESTER FILM CAP. (PB FREE) 0.0012µF/ 100V J CA2A122DT018 C606 CERAMIC CAP. 560pF/2KV CA3D561PAN04 C607 POLYESTER FILM CAP. (PB FREE) 0.082µF/ 100V J CA2A823DT018 1. Parts that are not assigned part numbers (---------) are not available. C608 POLYESTER FILM CAP. (PB FREE) 0.0018µF/ 100V J CA2A182DT018 C631 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C632 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZPDL102 C633 CERAMIC CAP. B K 1500pF/1KV CCD3AKN0B152 C636# ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C638 ELECTROLYTIC CAP. 2200µF/6.3V M CE0KMZPDL222 C639 ELECTROLYTIC CAP. 2200µF/6.3V M CE0KMZPDL222 C640 ELECTROLYTIC CAP. 1000µF/10V M CE1AMASDL102 C641 ELECTROLYTIC CAP. 3300µF/10V M CE1AMZPDL332 C643 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZPDL102 C645 POLYESTER FILM CAP. (PB FREE) 0.0022µF/ 100V J CA2A222DT018 C646 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C647 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMAVSL101 NOTES: C.....±0.25% D.....±0.5% F.....±1% G.....±2% J......±5% K.....±10% M.....±20% N.....±30% Z.....+80/-20% DIGITAL MAIN CBA UNIT Ref. No. Description DIGITAL MAIN CBA UNIT Part No. A1DN2MMA-003 DVD MAIN CBA UNIT Ref. No. Description DVD MAIN CBA UNIT Part No. N7ETGKUP MAIN CBA Ref. No. Description MAIN CBA Consists of the following: Part No. A1DN2MP1-001 CAPACITORS C648 ELECTROLYTIC CAP. 47µF/25V M H7 CE1EMAVSL470 C649 ELECTROLYTIC CAP. 220µF/10V M H7 CE1AMAVSL221 C650 ELECTROLYTIC CAP. 220µF/10V M H7 CE1AMAVSL221 C652 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C653 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C654 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 CE1JMAVSL220 C655 ELECTROLYTIC CAP. 22µF/50V M H7 C656 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C661 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3 C681 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C682 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C683 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C684 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C201 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471 C685 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C202 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C691# CAP CERAMIC 4700pF/250V/M/KX CA2E472MR101 C203 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C692# SAFTY CAP. 2200pF/250V KX CA2E222MR101 C204 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C802 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C207 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C805 ELECTROLYTIC CAP. 330µF/25V M CE1EMASDL331 C209 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C806 ELECTROLYTIC CAP. 330µF/25V M CE1EMASDL331 C214 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C807 CHIP CERAMIC CAP.(1608) B K 0.022µF/25V CHD1EK30B223 C215 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C808 CHIP CERAMIC CAP.(1608) B K 0.022µF/25V CHD1EK30B223 C216 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 C809 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 CHD1CK30B105 C217 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C810 CHIP CERAMIC CAP. (1608) B K 1µF/16V C218 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C811 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C219 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C812 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471 C220 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C813 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C221 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C816 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C301 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C817 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C302 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C818 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C303 ELECTROLYTIC CAP. 330µF/10V M CE1AMASDL331 C819 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 C304 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C821 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C825 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 CHD1JJ3CH391 C306 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C826 CHIP CERAMIC CAP.(1608) CH J 390pF/50V C309 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C827 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 C310 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C828 CHIP CERAMIC CAP.(1608) CH J 390pF/50V CHD1JJ3CH391 C311 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C829 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C401 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 C830 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C601# CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004 C831 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 2011/04/22 17-2 A1DN2EL.fm Ref. No. C832 Description CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V Ref. No. Part No. CHD1JZ30F104 C1053 Description ELECTROLYTIC CAP. 100µF/25V M H7 Part No. CE1EMASSL101 C833 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1054 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C906 CHIP CERAMIC CAP.(1608) CH J 390pF/50V CHD1JJ3CH391 C1056 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C907 CHIP CERAMIC CAP.(1608) CH J 390pF/50V CHD1JJ3CH391 C910 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 CN102 J3PHC08JG029 C911 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 PH CONNECTOR TOP 8P B8B-PH-K-S (LF)(SN) C912 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 CN201 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CONNECTORS C914 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 CN301 C915 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 CN302 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 C916 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 CN303 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CE0KMASDL221 CN702 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CN872 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 C917 ELECTROLYTIC CAP. 220µF/6.3V M C918 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101 C919 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C920 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 CN901 FFC CONNECTOR IMSA-9615S-26A-PP-A JC96J26ER007 CN902 JC62G13UG026 C922 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 CONNECTOR PRINT MES 00 6232 013 006 800+ C923 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271 CN1001# CONNECTOR PRINT OSU KW05-120-02-00 J30502KET001 C924 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 CN1002# CONNECTOR PRINT OSU KW05-120-02-00 J30502KET001 C925 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271 C926 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 D201 SWITCHING DIODE 1SS133(T-77) C927 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 D202 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 C928 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 D203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C929 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 D204 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1001 CAP CERAMIC (AX) 2200pF/50V/B/K CA1J222TU061 D205 DIODE ZENER 24BSC-T26 NDTC024BST26 C1002 POLYESTER FILM CAP. (PB FREE) 0.022µF/ 100V J CA2A223DT018 D206 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1003 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D207 DIODE ZENER 7V5BSA-T26 NDTA7R5BST26 C1004 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D208 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1005 POLYESTER FILM CAP. (PB FREE) 0.022µF/ 100V J CA2A223DT018 D209 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1006 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D303 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 C1007 CAP CERAMIC (AX) 2200pF/50V/B/K CA1J222TU061 D401 DIODE FR104-B NDLZ000FR104 DIODE ZENER 10BSB-T26 NDTB010BST26 DIODES QDTZ001SS133 C1008 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D402 C1009 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D404 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1010 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1011 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZPDL102 D406 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1012 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221 D407 C1014 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D408 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1015 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D409 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1016 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 D410 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 QDTZ001SS133 C1018 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D411 C1019 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221 D412 SWITCHING DIODE 1SS133(T-77) C1020 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D413 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1023 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D414 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26 QDTZ001SS133 C1024 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D415 SWITCHING DIODE 1SS133(T-77) C1025 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D416 DIODE ZENER 10BSB-T26 NDTB010BST26 C1026 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D417 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1027 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D601# DIODE 1N5397BD NDL1001N5397 DIODE 1N5397BD NDL1001N5397 NDL1001N5397 C1028 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D602# C1031 POLYESTER FILM CAP. (PB FREE) 0.0027µF/ 100V J CA2A272DT018 D603# DIODE 1N5397BD D604# DIODE 1N5397BD NDL1001N5397 C1032 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D605 DIODE ZENER 4V3BSB-T26 NDTB4R3BST26 NDTB027BST26 C1033 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D606# DIODE ZENER 27BSB-T26 C1034 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D607# DIODE ZENER 39BSB-T26 NDTB039BST26 C1035 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D608# SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1037 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 D610 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1038 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D612 DIODE ZENER 1ZB220-YBB NDWZ01ZB220Y C1039 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D631 DIODE SCHOTTKY SB2A0BD NDWZ000SB2A0 C1040 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 D632 DIODE SCHOTTKY 30PHA20 QDLZ030PHA20 C1041 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D633# DIODE ZENER 1ZB43BB NDWZ0001ZB43 C1042 CHIP CERAMIC CAP.(1608) F Z 0.22µF/50V CHD1JZ30F224 D636 DIODE FR104-B NDLZ000FR104 C1043 CHIP CERAMIC CAP.(1608) B K 0.22µF/16V CHD1CK30B224 D637# DIODE ZENER 36BSB-T26 NDTB036BST26 C1044 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D638 SCHOTTKY BARRIER DIODE SB240-B/P NDWZ000SB240 D639 DIODE FAST RECOVERY FR151-B/P NDWZ0FR151BP C1045 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1052 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 2011/04/22 17-3 A1DN2EL.fm Ref. No. D640 Description Ref. No. Part No. Description Part No. SCHOTTKY BARRIER DIODE SB240-B/P NDWZ000SB240 D1036 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D641 DIODE SCHOTTKY SB360BH NDWZ000SB360 D1037 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D642 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1038 WIRE CP STP-S-0.50 XZ40F0REN001 D643 FAST RECOVERY DIODE FR252 NDWZ000FR252 D1045 SWITCHING DIODE 1SS133(T-77) D645 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D646 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC201 IC TL3472CDR D648 DIODE ZENER HZS5.6NB2TE-EQ QDTB0HZS5R6N IC601# PHOTO COUPLER LTV817MCF NPECLTV817MF D649# DIODE ZENER 3V3BSB-T26 NDTB3R3BST26 IC631 IC LD1117V NSZBA0SSS046 D650 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 IC801 AUDIO AMP IC TDA1517P/N3 112 NSCA0SNXP003 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC803 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 D653 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC901 IC REGULATOR AP1117TG-U/TO-220/3P NSCA0SDES002 D654 DIODE FR154 NDLZ000FR154 IC902 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 D655 DIODE FR154 NDLZ000FR154 IC1001 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC PULSE-WIDTH-MODULATION CONT TL494CDR NSCA0T0TY006 D656 D657 DIODE ZENER 4V7BSB-T26 NDTB4R7BST26 IC1002 IC OPERATIONNAL AMPLIFIER KIA358F-EL NSZBA0TJY030 QDTZ001SS133 ICS NSZBA0TTY115 COILS D659 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038 D660 WIRE CP STP-S-0.50 XZ40F0REN001 L301 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 D662 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 L302 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 D665 WIRE CP STP-S-0.50 XZ40F0REN001 L303 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 LINE FILTER 5.0MH 96005 LLBG00ZKT004 XZ40F0REN001 D666 DIODE ZENER 10BSB-T26 NDTB010BST26 L601# D668# DIODE ZENER 27BSB-T26 NDTB027BST26 L901 WIRE CP STP-S-0.50 TRANSISTORS D670 SCHOTTKY BARRIER DIODE SB160 NDWZ000SB160 D804 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q171 TRANSISTOR KTC3199-GR-AT/P D805 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q172 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D808 DIODE ZENER 20BSB-T26 NDTB020BST26 Q201 TRANSISTOR 2SD400(F) QQUF002SD400 NQS4KTC3199P D809 DIODE ZENER 20BSB-T26 NDTB020BST26 Q202 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D901 DIODE ZENER 10BSC-T26 NDTC010BST26 Q203 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D902 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q205 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D903 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q206 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D905 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 Q207 TRANSISTOR 2SC2655-Y(TE6 F M) QQSY2SC2655F D906 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26 Q208 TRANSISTOR 2SA1020-Y(TE6 F M) QQSY2SA1020F D907 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q209 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D908 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q210 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D909 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q401 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1001 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q402 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1002 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q601# FET MOS TK5A50D(FUNAI QEWZTK5A50DQ D1003 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q602# TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1004 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q631 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1005 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26 Q633 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1006 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q634 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1007 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q635 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1008 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q636 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1009 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q637 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1010 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q638 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1011 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q639 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D1012 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q640 QQWZ2SC4881F D1013 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 NPN TRANSISTOR POWER 2SC4881F HFE MAX320 D1014 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q641 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1015 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q643 TRANSISTOR 2SA950-Y(TE2 F T) QQSY02SA950F D1016 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q801 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1018 DIODE ZENER 10BSB-T26 NDTB010BST26 Q901 TRANSISTOR 2SA950-Y(TE2 F T) QQSY02SA950F D1020 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26 Q902 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1021 DIODE ZENER 15BSB-T26 NDTB015BST26 Q903 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1022 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q904 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1023 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q905 TRANSISTOR 2SD400(F) QQUF002SD400 D1024 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q906 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1025 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q907 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1026 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1001 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1027 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1002 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1028# DIODE ZENER 4V7BSB-T26 NDTB4R7BST26 Q1003 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1029 DIODE ZENER 16BSB-T26 NDTB016BST26 Q1004 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1030 DIODE ZENER 16BSB-T26 NDTB016BST26 Q1005# FET MOS SMD TPC8214-H QF2ZTPC8214H D1034 DIODE ZENER 9V1BSB-T26 NDTB9R1BST26 Q1006 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P 2011/04/22 17-4 A1DN2EL.fm Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W F 36.0k Ω RTW3602HH008 R406 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 R407 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 NQS4KTC3199P R408 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 TRANSISTOR 2SA950-Y(TE2 F T) QQSY02SA950F R409 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 Q1012 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R411 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 Q1014 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R412 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 Q1015 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R413 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 Q1016 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R601# GLASS GLAZE RES. 1/2W J 1M Ω RXX2JZLZ0105 Q1017 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R602 CEMENT RES. 3W K 1.2 Ω RW031R2PG007 Q1018 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R603 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 Q1019 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R604 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 Q1023 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R605 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 Q1024 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R606 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 R607 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 Q1007 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R403 Q1008 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1009 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1010 TRANSISTOR KTC3199-GR-AT/P Q1011 RESISTORS R171 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R608 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R172 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R609 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 R175 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R610# METAL OXIDE FILM RES. 2W J 0.39 Ω RN02R39ZU001 R201 METAL OXIDE FILM RES. 1W J 5.6 Ω RN015R6ZU001 R611 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R202 RES CHIP 1608 1/10W F 9.10k Ω RTW9101HH008 R612 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R203 RES CHIP 1608 1/10W F 510 Ω RTW5100HH008 R631 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R204 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 R632 RES CHIP 1608 1/10W D 1.10k Ω RTW1101HH007 R205 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 R633 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007 R206 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 R634 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R207 RES CARBON FILM T 1/4W J 6.8k Ω RCX4682T1001 R635 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R208 RES CARBON FILM T 1/4W J 6.8k Ω RCX4682T1001 R637 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R209 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 R638 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R210 RES CHIP 1608 1/10W J 6.8k Ω RRJ682RYL002 R639 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R211 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R640 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R212 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R641 RES CHIP 1608 1/10W F 120 Ω RTW1200HH008 R213 RES CHIP 1608 1/10W J 27k Ω RRJ273RYL002 R642 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 R214 RES CHIP 1608 1/10W J 3.3k Ω RRJ332RYL002 R643 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 R215 RES CARBON FILM T 1/4W J 330 Ω RCX4331T1001 R644 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 R216 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R645 RES CHIP 1608 1/10W F 7.50k Ω RTW7501HH008 R217 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R646 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R218 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001 R647 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 R219 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R648 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R220 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 R649# RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R221 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R650 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R222 RES CARBON FILM T 1/4W J 120 Ω RCX4121T1001 R651# RES CARBON FILM T 1/4W J 15 Ω RCX4150T1001 R223 RES CARBON FILM T 1/4W J 15k Ω RCX4153T1001 R652 WIRE CP STP-S-0.50 XZ40F0REN001 R224 RES CHIP 1608 1/10W J 1 Ω RRJ1R0RYL002 R653 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R225 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R654 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R226 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R655 RES CARBON FILM T 1/4W J 470 Ω RCX4471T1001 R227 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R656 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R228 WIRE CP STP-S-0.50 XZ40F0REN001 R658 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R229 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R659 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 R230 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R660 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007 R231 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 R661 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R232 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R662 RES CARBON FILM T 1/4W J 39 Ω RCX4390T1001 R233 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R663 RES CARBON FILM T 1/4W J 3.3 Ω RCX43R3T1001 R234 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R664 RES CARBON FILM T 1/4W J 3.9 Ω RCX43R9T1001 R238 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R665 RES CARBON FILM T 1/4W J 3.9 Ω RCX43R9T1001 R239 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R666 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R240 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 R667 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R302 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R668 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R303 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R669 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R304 RES CHIP 1608 1/10W J 82 Ω RRJ820RYL002 R670 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 R305 RES CHIP 1608 1/10W J 82 Ω RRJ820RYL002 R671 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R313 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R672 METAL OXIDE RES. 1W J 0.18 Ω RN01R18ZU001 R401# RES CHIP 1608 1/10W J 1 Ω RRJ1R0RYL002 R673 RES CHIP 1608 1/10W F 3.60k Ω RTW3601HH008 R402 RES CHIP 1608 1/10W F 5.60k Ω RTW5601HH008 R674 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 R675 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 2011/04/22 17-5 A1DN2EL.fm Ref. No. Description Part No. Ref. No. Description Part No. RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001 R927 RES CARBON FILM T 1/4W J 10 Ω R677 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R928 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R678 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R929 RES CARBON FILM T 1/4W J 1.2 Ω RCX41R2T1001 RN026R8ZU001 R676 RCX4100T1001 R679 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R930 METAL OXIDE FILM RES. 2W J 6.8 Ω R681 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R931 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R682 WIRE CP STP-S-0.50 XZ40F0REN001 R932 WIRE CP STP-S-0.50 XZ40F0REN001 R683 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R933 RES CARBON FILM T 1/4W J 100k Ω RCX4104T1001 R684 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R935 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R685 RES CHIP 1608 1/10W F 620 Ω RTW6200HH008 R936 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R686 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R940 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R688 RES CARBON FILM T 1/4W J 1.0 Ω RCX41R0T1001 R941 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R689 RES CARBON FILM T 1/4W J 33 Ω RCX4330T1001 R942 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R690 RES CARBON FILM T 1/4W J 3.3 Ω RCX43R3T1001 R943 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R699 RES CARBON FILM T 1/4W J 56 Ω RCX4560T1001 R1001 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R803 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1002 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R804 RES CHIP 1608 1/10W J 8.2 Ω RRJ8R2RYL002 R1003 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R805 RES CHIP 1608 1/10W J 8.2 Ω RRJ8R2RYL002 R1004 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R806 WIRE CP STP-S-0.50 XZ40F0REN001 R1005 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R807 WIRE CP STP-S-0.50 XZ40F0REN001 R1006 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R808 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R1007 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R809 RES CHIP 1608 1/10W J 360 Ω RRJ361RYL002 R1008 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R810 RES CHIP 1608 1/10W J 5.6k Ω RRJ562RYL002 R1009 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R811 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1010 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R813 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1011 RES CHIP 1608 1/10W J 12k Ω RRJ123RYL002 R814 RES CHIP 1608 1/10W J 5.6k Ω RRJ562RYL002 R1012 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R815 RES CHIP 1608 1/10W J 470 Ω RRJ471RYL002 R1013 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R816 RES CHIP 1608 1/10W J 470 Ω RRJ471RYL002 R1014 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R817 RES CHIP 1608 1/10W J 18k Ω RRJ183RYL002 R1015 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R818 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R1017 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R819 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1018 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R820 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R1019 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R821 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1020 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R823 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1022 RES CHIP 1608 1/10W J 33k Ω RRJ333RYL002 R826 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1023 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R830 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1024 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 R834 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1025 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 R836 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1026 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R837 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1027 RES CHIP 1608 1/10W J 5.1k Ω RRJ512RYL002 R838 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1028 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R842 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1029 RES CARBON FILM T 1/4W J 1.8k Ω RCX4182T1001 R904 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1030 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R905 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1031 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001 R906 RES CARBON FILM T 1/4W J 560 Ω RCX4561T1001 R1032# METAL OXIDE FILM RES. 2W J 0.33 Ω RN02R33ZU001 R907 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 R1035 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R908 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 R1036 RES CHIP 1608 1/10W F 15.0k Ω RTW1502HH008 R909 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 R1037 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R910 RES CHIP.(1608) 1/10W J 0.30 Ω RRXAR30HH007 R1038 RES CHIP 1608 1/10W J 240k Ω RRJ244RYL002 R911 RES CHIP.(1608) 1/10W J 0.30 Ω RRXAR30HH007 R1039 RES CHIP 1608 1/10W F 68.0k Ω RTW6802HH008 R912 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R1040 RES CHIP 1608 1/10W F 6.20k Ω RTW6201HH008 R913 RES. CARBON FILM J 1/2W J 3.3 Ω RCX23R3T1003 R1041 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R914 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 R1042 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R915 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1043 RES CHIP 1608 1/10W F 5.10k Ω RTW5101HH008 R916 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1044 RES CARBON FILM T 1/4W G 5.1k Ω RCX4512T1002 R917 RES CARBON FILM T 1/4W J 390 Ω RCX4391T1001 R1045 RES CHIP 1608 1/10W J 240k Ω RRJ244RYL002 R918 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1046 RES CHIP 1608 1/10W J 24k Ω RRJ243RYL002 R919 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R1048 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R920 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008 R1049 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R921 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 R1050 RES CHIP 1608 1/10W J 390k Ω RRJ394RYL002 R922 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001 R1051 RES CHIP 1608 1/10W J 390k Ω RRJ394RYL002 R923 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R1052 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 R924 RES CARBON FILM T 1/4W J 5.6 Ω RCX45R6T1001 R1054 RES CHIP 1608 1/10W F 5.60k Ω RTW5601HH008 R925 RES CARBON FILM T 1/4W J 5.6 Ω RCX45R6T1001 R1055 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 R926 RES CARBON FILM T 1/4W J 470 Ω RCX4471T1001 R1056 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 2011/04/22 17-6 A1DN2EL.fm Ref. No. R1058 Description Ref. No. Part No. Description Part No. RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 JS1005 WIRE CP STP-S-0.50 XZ40F0REN001 R1059 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 JS1007 WIRE CP STP-S-0.50 XZ40F0REN001 R1060 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 JS1011 WIRE CP STP-S-0.50 XZ40F0REN001 R1061 RES CHIP 1608 1/10W J 33k Ω RRJ333RYL002 JS1012 WIRE CP STP-S-0.50 XZ40F0REN001 R1062 RES CHIP 1608 1/10W J 390k Ω RRJ394RYL002 L13 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080 R1064 RES CHIP 1608 1/10W J 33k Ω RRJ333RYL002 SA601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB R1065 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 T601# TRANS POWER BCK-28-9923 LTT2PC0XB044 R1066 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 TM601 EYELET TYPE D-1 0VM406868 R1067 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 TM602 EYELET TYPE D-1 0VM406868 R1068 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 T1002# TRANS INVERTER HVT-160 LTZ3PZ0XB014 R1069 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 TU302 TUNER UNIT ATSC TDAU4-D05A UTNATS0AL002 R1070 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1071 RES CHIP 1608 1/10W F 4.30k Ω RTW4301HH008 R1072 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1073 RES CHIP 1608 1/10W F 1.20k Ω RTW1201HH008 R1074 RES CARBON FILM T 1/4W J 100k Ω R1081 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 R1082 RES CHIP 1608 1/10W F 68.0k Ω RTW6802HH008 R1083 RES CHIP 1608 1/10W F 1.00M Ω RTW1004HH008 R1084 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1086 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 R1087 RES CHIP 1608 1/10W F 68.0k Ω RTW6802HH008 R1088 RES CHIP 1608 1/10W F 1.00M Ω RTW1004HH008 JACK ASSEMBLY Ref. No. RCX4104T1001 Description Part No. JACK ASSEMBLY Consists of the following A1DN2MJC-001 JACK CBA(MJC-A) FUNCTION CBA(MJC-B) A1DN2MJC-001-JK A1DN2MJC-001-FN JACK CBA Ref. No. Description JACK CBA(MJC-A) Consists of the following Part No. ---------- R1089 RES CHIP 1608 1/10W F 12.0k Ω RTW1202HH008 R1090 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 R1091 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C703 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1092 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C704 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1093 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C723 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1094 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C724 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1095 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001 C731 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 R1099 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 C732 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 R1100 WIRE CP STP-S-0.50 XZ40F0REN001 C733 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 R1105 RES CHIP 1608 1/10W J 3.3k Ω RRJ332RYL002 C734 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1106 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 C735 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1107 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 C736 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1108 WIRE CP STP-S-0.50 XZ40F0REN001 C743 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1109 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 C744 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1110 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 C751 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 CAPACITORS R1111 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 C752 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R1112 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C753 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R1117 WIRE CP STP-S-0.50 XZ40F0REN001 C754 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1118 RES CARBON FILM T 1/4W J 1.2 Ω RCX41R2T1001 C755 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C756 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 CHD1CZ30F105 MISCELLANEOUS AC CORD PB8K9F9110A-057 WAC0172LW008 C757 CHIP CERAMIC CAP. (1608) F Z 1µF/16V B13 HEAT SINK PMU A8A70UH 1EM324377 C758 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 B14 POW HEAT SINK A7120UH 1EM423993 C771 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101 BC301 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 C772 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 C773 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 BC801 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 C775 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 BC901 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 C776 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 BC902 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C841 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 F601# FUSE STC4A125V U/CT PAGE20CW3402 C842 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 CHD1JJ3CH330 AC601# FH601 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 C843 FH602 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 C845 CHIP CERAMIC CAP.(1608) CH J 33pF/50V JS101 WIRE CP STP-S-0.50 XZ40F0REN001 JS304 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 CN701 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 JS305 WIRE CP STP-S-0.50 XZ40F0REN001 CN871 J3PHC02JG029 JS306 WIRE CP STP-S-0.50 XZ40F0REN001 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) JS801 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 D701 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 JS803 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 D702 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 JS804 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 D703 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 D704 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 JS802 2011/04/22 CONNECTORS DIODES 17-7 A1DN2EL.fm Ref. No. Description Ref. No. Part No. Description Part No. DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 R791 RES CHIP 1608 1/10W J 82k Ω RRJ823RYL002 D706 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 R792 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 D707 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R793 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 D708 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R794 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 D709 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 R795 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 D710 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R796 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 R797 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 QSZBA0TTS162 R843 RES CHIP 1608 1/10W J 110 Ω RRJ111RYL002 R844 RES CHIP 1608 1/10W J 220 Ω RRJ221RYL002 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 D705 IC IC771 IC SWITCHING TC4052BF(ELNF) COILS L851 WIRE CP STP-S-0.50 XZ40F0REN001 R845 L852 WIRE CP STP-S-0.50 XZ40F0REN001 R846 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 L853 WIRE CP STP-S-0.50 XZ40F0REN001 R847 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R848 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 NQS4KTC3199P R851 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R852 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 TRANSISTORS Q722 TRANSISTOR KTC3199-GR-AT/P Q771 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q773 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q774 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P BC771 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 Q841 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P BC841 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 JK711 JACK HPEP SML PCB S PJ-358H JXSJ020YUQ01 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 MISCELLANEOUS RESISTORS R711 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK721 R712 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK722 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 R717 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 JK731 JACK RCA PCB S GREEN 01/RCA-101H(GN) JXRJ010YUQ03 RRJ563RYL002 JK732 JACK RCA PCB S BLUE 01/RCA-101H(BL) JXRJ010YUQ04 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 R718 RES CHIP 1608 1/10W J 56k Ω R721 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK733 R722 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK741 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 R727 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 JK742 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 R728 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 JK751 JACK SW DIN PCB L DIN-435C(777D) JYEL040YUQ03 JACK RCA PCB L RCA-101S(1)-03 JXRL010YUQ12 R731 RES CHIP 1608 1/10W F 75.0 Ω RTW75R0HH008 JK752 R732 RES CHIP 1608 1/10W F 75.0 Ω RTW75R0HH008 JK753 JACK RCA PCB L RCA-101S(1)-04 JXRL010YUQ13 R733 RES CHIP 1608 1/10W F 75.0 Ω RTW75R0HH008 JK754 JACK SW RCA PCB L RCA-102F(RD) JYRL010YUQ05 R734 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 JK841 JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06 JACK SW HPEP SML PCB L PJ-350 JYSL010YUQ03 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R735 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 JK851 R736 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 JS701 R741 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R742 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R747 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 R748 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 FUNCTION CBA Ref. No. Description FUNCTION CBA(MJC-B) Consists of the following: Part No. ---------- R751 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R752 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R753 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 C103 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470 R754 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 C104 CHIP CERAMIC CAP. B K 330pF/50V CHD1JK30B331 R755 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 C107 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R756 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 C108 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 R757 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 C109 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 R758 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 C951 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 R763 RES CARBON FILM T 1/4W J 56k Ω RCX4563T1001 R764 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 RES CHIP 1608 1/10W J 10k Ω D101 ZENER DIODE EDZTE61 6.8B R772 RRJ103RYL002 LED L-53HT NP4Z000L53HT R773 RES CHIP 1608 1/10W J 10k Ω D103 RRJ103RYL002 D104 LED GREEN 333GT/E(FNA) NPWZ33GTEFNA D950 LED (YELLOW) LTL-307Y NPWZ0LTL307Y R774 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R775 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R780 RES CHIP 1608 1/10W J 82k Ω RRJ823RYL002 R781 RES CHIP 1608 1/10W J 82k Ω RRJ823RYL002 R782 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001 R783 RES CHIP 1608 1/10W J 82k Ω RRJ823RYL002 R784 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R785 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R786 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R787 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R788 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001 R789 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001 R790 RES CHIP 1608 1/10W J 82k Ω RRJ823RYL002 2011/04/22 CAPACITORS DIODES QD1B00EDZ6R8 RESISTORS 17-8 R106 RES CARBON FILM T 1/4W J 100 Ω R107 RES CHIP 1608 1/10W J 3.3k Ω RRJ332RYL002 R108 RES CHIP 1608 1/10W J 220 Ω RRJ221RYL002 RCX4101T1001 R109 RES CHIP 1608 1/10W J 220 Ω RRJ221RYL002 R110 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R111 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R112 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R113 RES CHIP 1608 1/10W F 4.70k Ω RTW4701HH008 R114 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008 R115 RES CHIP 1608 1/10W F 4.70k Ω RTW4701HH008 R116 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 A1DN2EL.fm Ref. No. Description Part No. R118 RES CHIP 1608 1/10W F 10.0k Ω R950 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R951 WIRE CP STP-S-0.50 XZ40F0REN001 RTW1002HH008 R952 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 R953 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 R956 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 SWITCHES SW104 TACT SWITCH SKHHLMA010 SST0101AL049 SW105 TACT SWITCH SKHHLMA010 SST0101AL049 SW106 TACT SWITCH SKHHLMA010 SST0101AL049 SW107 TACT SWITCH SKHHLMA010 SST0101AL049 SW108 TACT SWITCH SKHHLMA010 SST0101AL049 SW109 TACT SWITCH SKHHLMA010 SST0101AL049 SW951 TACT SWITCH SKHHLMA010 SST0101AL049 SW952 TACT SWITCH SKHHLMA010 SST0101AL049 SW953 TACT SWITCH SKHHLMA010 SST0101AL049 MISCELLANEOUS CL101 WIRE ASSEMBLY 8PIN 8PIN/100MM/AWG 26 RS101 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 2011/04/22 WX1A01N0-001 17-9 A1DN2EL.fm PARTS LIST [19MD301B/F7 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LD190SS2 (Serial No.: DS1) Ref. No. Description STAND ASSEMBLY A9DN0UH Part No. 1ESA24416 A1 FRONT CABINET A94N0UH 1EM023465A A5 DECORATION PLATE A1DN0UH 1EM225963 A6# RATING LABEL A1DN0UH ---------- L17 STAND SCREW KIT A1DN0UH 1ESA28791 S1 CARTON A1DN0UH 1EM434659 X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579 X2# OWNERS MANUAL A1DA0UH 1EMN28219 X3 REMOTE CONTROL NF801UD 192/ ECNLC7D1/NF801UD NF801UD X4 DRY BATTERY R03/2S XB0M451T0006 X6 QUICK START GUIDE A1DN0UH 1EMN28180 X10 REGISTRATION CARD (MAGNAVOX) A17N0UH 1EMN27759 2011/04/22 17-10 A1DN0CA.fm Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25% D.....±0.5% F.....±1% G.....±2% J......±5% K.....±10% M.....±20% N.....±30% Z.....+80/-20% Different parts from the original model LD190SS2 (Serial No.: DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A1DN0MMA-001 DVD MAIN CBA UNIT N7EX2KUP 2011/04/22 17-11 A1DN0EL.fm PARTS LIST [LD190EM2 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LD190SS2 (Serial No.: DS1) Ref. No. Description Part No. STAND ASSEMBLY A9DN0UH 1ESA24416 A1 FRONT CABINET A1DN1UH 1EM027809 A3 Not used A5 Not used A6# RATING LABEL A1DN1UH ---------- A11 FUNCTION KNOB A1DN1UH 1EM330659 A13 LED LENS A1DN1UH 1EM330660 B28 SHIELD PLATE A1DN1UH 1EM330661 L17 STAND SCREW KIT A1DN0UH 1ESA28791 S1 CARTON A1DN1UH 1EM434822 S2 STYROFOAM TOP A1DN1UH 1EM027810 S3 STYROFOAM BOTTOM A1DN1UH 1EM027811 X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579 X2# OWNERS MANUAL A1DA1UH 1EMN27999 X6 QUICK START GUIDE A1DN1UH 1EMN27682 X10 REGISTRATION CARD (EMERSON) A17N1UH 1EMN27763 2011/04/22 17-12 A1DN1CA.fm Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25% D.....±0.5% F.....±1% G.....±2% J......±5% K.....±10% M.....±20% N.....±30% Z.....+80/-20% Different parts from the original model LD190SS2 (Serial No.: DS1) There are no different parts from the original model LD190SS2 (Serial No.: DS1). Refer to the parts list for the original model LD190SS2 (Serial No.: DS1). 2011/04/22 17-13 A1DN1EL.fm PARTS LIST [LD190EM2 (Serial No.: DS2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LD190SS2 (Serial No.: DS1) Ref. No. Description Part No. STAND ASSEMBLY A9DN0UH 1ESA24416 A1 FRONT CABINET A1DN1UH 1EM027809 A3 Not used A5 Not used A6# RATING LABEL A1DN1UH ---------- A11 FUNCTION KNOB A1DN1UH 1EM330659 A13 LED LENS A1DN1UH 1EM330660 B28 SHIELD PLATE A1DN1UH 1EM330661 L17 STAND SCREW KIT A1DN0UH 1ESA28791 LCD1 LCD MODULE 18.5INCH WIDE CPT 18.5INCH WXGA UJ19PXA S1 CARTON A1DN1UH 1EM434822 S2 STYROFOAM TOP A1DN1UH 1EM027810 S3 STYROFOAM BOTTOM A1DN1UH 1EM027811 X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579 X2# OWNERS MANUAL A1DA1UH 1EMN27999 X6 QUICK START GUIDE A1DN1UH 1EMN27682 X10 REGISTRATION CARD (EMERSON) A17N1UH 1EMN27763 2011/04/22 17-14 A1DN5CA.fm Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25% D.....±0.5% F.....±1% G.....±2% J......±5% K.....±10% M.....±20% N.....±30% Z.....+80/-20% Different parts from the original model LD190SS2 (Serial No.: DS1) Ref. No. Description DIGITAL MAIN CBA UNIT 2011/04/22 Part No. A1DN5MMA-001 17-15 A1DN5EL.fm 19MD311B/F7(A1DN4UH)(Serial No.: DS1) 20110407 19MD311B/F7(A1DN4UH)(Serial No.: DS1) Different parts from the original model LD190SS2(DS1) Ref. No. Description MECHANICAL PARTS STAND ASSEMBLY A9DN0UH A1 FRONT CABINET A1DN4UH A3 Not used A5 Not used A6! RATING LABEL A1DN4UH A11 FUNCTION KNOB A1DN1UH A13 LED LENS A1DN1UH B28 SHIELD PLATE A1DN1UH L17 STAND SCREW KIT A1DN0UH S1 CARTON A1DN4UH S2 STYROFOAM TOP A1DN1UH S3 STYROFOAM BOTTOM A1DN1UH X1 POLYETHYLENE BAG HDPE 180X340XT0.03 X2! OWNERS MANUAL A1DA0UH X3 REMOTE CONTROL NF801UD 192/ECNLC7D1/NF801UD X4 DRY BATTERY R03/2S X6 QUICK START GUIDE A1DN0UH X10 REGISTRATION CARD (MAGNAVOX) A17N0UH Parts No. 1ESA24416 1EM126514 ---------1EM330659 1EM330660 1EM330661 1ESA28791 1EM435966 1EM027810 1EM027811 1EM435579 1EMN28219A NF801UD XB0M451T0006 1EMN28180A 1EMN27759 ELECTRICAL PARTS DIGITAL MAIN CBA UNIT A1DN0MMA-001 DVD MAIN CBA UNIT N7EX2KUP 1 / 1 page REVISION HISTORY Chassis FL11.8 • 2011-02-07 LD190SS2 (Serial No. : DS1) added • 2011-04-11 19MD301B/F7 (Serial No. : DS1) added • 2011-04-11 LD190EM2 (Serial No. : DS1) added • 2011-04-25 LD190EM2 (Serial No. : DS2) added • TBD 19MD311B/F7 (Serial No. : DS1) added 18-1 FL11.8REV COMPARISON LIST OF MODEL NAME Chassis FL11.8 LD190SS2 (DS1) A1DN2UH 19MD301B/F7 (DS1) A1DN0UH LD190EM2 (DS1) A1DN1UH (DS2) A1DN5UH (DS1) A1DN4UH 19MD311B/F7 FL11.8COM